Owner's manual | Barco R9002400 Owner`s manual

BARCO PROJECTION SYSTEMS
CiNE
9
R9002400
R9002401
OWNER'S MANUAL
Date :
31012002
Rev. :
02
Art. No. :
R5976194
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, january 2002.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO n.v./Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : +32/56/368211
Fax : +32/56/351651
E-mail : [email protected]
Visite Barco at the web : http://www.barco.com
Printed in Belgium
Table of Content
i
CONTENT
SAFETY INSTRUCTIONS..................................................................................................... 1-1
Safety Instructions .............................................................................................................................................. 1-1
Notice on Safety ...............................................................................................................................................................................
installation INSTRUCTIONS ...................................................................................................... ......................................................
OWNER’S RECORD ................................................................................................................. ......................................................
Safety indication on the product ......................................................................................................................................................
Safety Warning .................................................................................................................................................................................
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) ............................................................................................
On Safety .........................................................................................................................................................................................
Caution on Fire Hazard ....................................................................................................................................................................
On installation ...................................................................................................................................................................................
On servicing .....................................................................................................................................................................................
On cleaning ......................................................................................................................................................................................
On repacking ....................................................................................................................................................................................
On illumination ..................................................................................................................................................................................
1-1
1-1
1-1
1-1
1-2
1-2
1-2
1-3
1-3
1-3
1-3
1-4
1-4
Note .................................................................................................................................................................... 1-4
Definition ........................................................................................................................................................................................... 1-4
CONNECTIONS ................................................................................................................... 2-1
Power Connection to Projector ........................................................................................................................... 2-1
AC Power (mains) Cord Connection ............................................................................................................................................... 2-1
Power Check .................................................................................................................................................................................... 2-1
Switching On/Off .............................................................................................................................................................................. 2-1
Source Connections ........................................................................................................................................... 2-2
Input locations .................................................................................................................................................... 2-2
Input facilities .................................................................................................................................................................................... 2-2
Which source to which input ............................................................................................................................................................ 2-2
Composite Video source. ................................................................................................................................... 2-3
Which signals to the Video Input ? ...................................................................................................................................................
Video input selection ........................................................................................................................................................................
Note on Loop-through ......................................................................................................................................................................
75 W Termination Switch for Video ...................................................................................................................................................
2-3
2-3
2-3
2-3
S-Video or Video source to port 2 ...................................................................................................................... 2-3
Which Signals to port 2 ....................................................................................................................................................................
Pin configuration 4 pin connector ....................................................................................................................................................
Input selection port 2 ........................................................................................................................................................................
Input Priority setting .........................................................................................................................................................................
Note on Loop-through ......................................................................................................................................................................
75 W Termination Switch for port 2 ..................................................................................................................................................
2-3
2-3
2-4
2-4
2-4
2-4
RGB Analog source to port 3 .............................................................................................................................. 2-5
Which signal to port 3 ....................................................................................................................................................................... 2-5
Pin configuration D9 connector of the Analog input. ............................................................................ ........................................... 2-5
RGB Analog source with composite sync to port 4/5. ........................................................................................ 2-5
Which signal to port 4/5 .................................................................................................................................................................... 2-5
RGBS or RGsB input selection ....................................................................................................................................................... 2-5
RGB Analog source with Tri-level sync to port 4/5. ............................................................................................. 2-6
Which signal to port4/5 ..................................................................................................................................................................... 2-6
RGB3S or RG3sB input selection ................................................................................................................................................... 2-6
Component source to port 4/5. ........................................................................................................................... 2-6
Which signal to port 4/5 .................................................................................................................................................................... 2-6
Component video input selection ..................................................................................................................................................... 2-6
RS232 Connection .............................................................................................................................................. 2-6
RS232 input and RS232 output of the projector. ............................................................................................................................. 2-6
Communication port for communication with peripherals .................................................................................... 2-6
Connecting a RCVDS 05 switcher to the projector. ........................................................................................................................ 2-6
GETTING STARTED ............................................................................................................ 3-1
Remote Control & Local Keypad ........................................................................................................................ 3-1
Battery Installation in the RCU ......................................................................................................................................................... 3-1
How to replace the batteries in the RCU ? ...................................................................................................................................... 3-1
Overview of Functions ..................................................................................................................................................................... 3-2
Operating the Projector ....................................................................................................................................... 3-3
5976194 BARCOCINE 9 31012002
i-1
Table of Content
Switching on ..................................................................................................................................................................................... 3-3
Start up in Operational Mode ........................................................................................................................................................... 3-3
Start up in Stand by Mode ................................................................................................................................................................ 3-3
Stationary Image Warning .................................................................................................................................. 3-3
RCU Commands to the Projector ....................................................................................................................... 3-4
Pointing the RCU to the reflective screen ....................................................................................................................................... 3-4
Point the front of the RCU towards one of the IR sensors in the projector. ................................................................................... 3-4
RCU used in a hardwired configuration. ......................................................................................................................................... 3-4
Projector address ............................................................................................................................................... 3-5
Why a projector address ? .............................................................................................................................................................. 3-5
Set up an Individual Projector Address ........................................................................................................................................... 3-5
How to control the projector or projectors ? ................................................................................................................................... 3-5
Common Address ............................................................................................................................................................................ 3-5
Before using the RCU ...................................................................................................................................................................... 3-5
Display the Projector Address on the Screen. ............................................................................................................................... 3-5
How to program an address into the RCU? .................................................................................................................................... 3-5
Controlling the Projector ..................................................................................................................................... 3-6
Input selection modes ......................................................................................................................................................................
When the source is selected ...........................................................................................................................................................
Picture controls ............................................................................................................... .................................................................
Sound controls .................................................................................................................................................................................
The Pause key. ................................................................................................................................................................................
The Freeze key. ...............................................................................................................................................................................
3-6
3-6
3-7
3-7
3-7
3-7
START UP OF THE ADJUSTMENT MODE ......................................................................... 4-1
Adjustment Mode ............................................................................................................................................... 4-1
Start Up ............................................................................................................................................................................................. 4-1
Possible Paths .................................................................................................................................................................................. 4-1
MAIN MENU ......................................................................................................................... 5-1
Main Menu .......................................................................................................................................................... 5-1
Overview Flowchart ......................................................................................................................................................................... 5-1
Image Control ..................................................................................................................................................... 5-2
Starting Up ........................................................................................................................................................................................ 5-2
Line Multiplier ..................................................................................................................................................... 5-2
Why Line Multiplying ......................................................................................................................................................................... 5-2
How to change the Multiplier Setting ................................................................................................................................................ 5-2
Line Multiplier ON/OFF .................................................................................................................................................................... 5-2
Multiplier Mode ................................................................................................................................................... 5-3
What can be selected within the multiplier mode ? ......................................................................................................................... 5-3
How to start up the Multiplier Mode menu ? .................................................................................................................................... 5-3
How to change the scan rate ? ....................................................................................................................................................... 5-3
Motion Processing .............................................................................................................................................. 5-3
Why Motion Processing ? ................................................................................................................................................................ 5-3
How to activate ? .............................................................................................................................................................................. 5-3
Video Equalizing ................................................................................................................................................. 5-4
What can be done ? ......................................................................................................................................................................... 5-4
How to select Video Equalizing ? ..................................................................................................................................................... 5-4
How to adjust the Video Equalizing ? ............................................................................................................................................... 5-4
Noise Reduction ................................................................................................................................................. 5-4
What can be done ? ......................................................................................................................................................................... 5-4
How to select and adjust the Noise Reduction ? ............................................................................................................................ 5-4
Contrast Enhancement ....................................................................................................................................... 5-4
What can be done ? ......................................................................................................................................................................... 5-4
How to select and adjust the contrast enhancement ? .................................................................................................................. 5-5
Color Adjust ........................................................................................................................................................ 5-5
What can be done ? ......................................................................................................................................................................... 5-5
How to select 'Color Adjust' and to select a new color temperature? ........................................................................................... 5-5
Format Select ..................................................................................................................................................... 5-5
What can be done ? .........................................................................................................................................................................
How to select a 'Format' ? ...............................................................................................................................................................
How to add a name to a 'Format' ? ..................................................................................................................................................
How to store the settings to a new 'Format' ? .................................................................................................................................
5-5
5-5
5-6
5-6
IRIS control ......................................................................................................................................................... 5-6
Start Up ............................................................................................................................................................................................. 5-6
Note .................................................................................................................................................................................................. 5-6
IRIS Touch Up .................................................................................................................................................... 5-6
What can be done ? ......................................................................................................................................................................... 5-6
How to start up the IRIS Touch Up ? ............................................................................................................................................... 5-7
IRIS Auto Converge ............................................................................................................................................. 5-7
What can be done ? ......................................................................................................................................................................... 5-7
i-2
5976194 BARCOCINE 9 31012002
Table of Content
How to start up the IRIS Auto Converge ? ...................................................................................................................................... 5-7
Sound Control ..................................................................................................................................................... 5-8
What can be done ? ......................................................................................................................................................................... 5-8
How to start up and to select the Sound Control ? ......................................................................................................................... 5-8
Function Keys .................................................................................................................................................... 5-8
What can be done ? ......................................................................................................................................................................... 5-8
How to get an overview of the programmed keys ? ....................................................................................................................... 5-8
Service Menus .................................................................................................................................................... 5-8
What can be done ? ......................................................................................................................................................................... 5-8
How to enter the Service Menu ? .................................................................................................................................................... 5-9
ENTERING THE SERVICE MENUS ..................................................................................... 6-1
Service menus .................................................................................................................................................... 6-1
What is available in the Service menus ? ........................................................................................................................................ 6-1
How to enter the Service Menus ? .................................................................................................................................................. 6-1
Password Protection ........................................................................................................................................................................ 6-1
Entering the password ..................................................................................................................................................................... 6-1
RANDOM ACCESS ADJUSTMENT MODE ........................................................................ 7-1
Random access adjustment mode. .................................................................................................................... 7-1
Starting Up ........................................................................................................................................................................................ 7-1
Overview Flowchart ......................................................................................................................................................................... 7-1
Selecting Setup Pattern ..................................................................................................................................... 7-2
Set up of the Selected Setup Pattern ? ........................................................................................................................................... 7-2
Note: .................................................................................................................................................................................................. 7-2
Internal Cross Hatch Pattern .............................................................................................................................. 7-3
When using the Internal Cross Hatch Pattern ? ................................................................................................. 7-3
Factory Preset Frequencies ............................................................................................................................................................ 7-3
Random access adjustment mode selection menu. ........................................................................................... 7-3
What is possible ? ............................................................................................................................................................................ 7-3
Picture Tuning .................................................................................................................................................... 7-4
Start up the Picture Tuning ............................................................................................................................................................... 7-4
Color Balance ..................................................................................................................................................... 7-4
What can be done ? ........................................................................................................................................... 7-4
How to select the Color Balance ? .................................................................................................................................................. 7-4
Fixed Color Balance ......................................................................................................................................................................... 7-4
Custom Color Balance. .................................................................................................................................................................... 7-4
Sync Fast/Slow Adjustment ............................................................................................................................... 7-5
What can be done ? ......................................................................................................................................................................... 7-5
How to setup the sync function ? .................................................................................................................................................... 7-5
Note .................................................................................................................................................................................................. 7-5
Peaking .............................................................................................................................................................. 7-6
What can be done ? ......................................................................................................................................................................... 7-6
How to set up ? ................................................................................................................................................................................ 7-6
Clamp Tuning ...................................................................................................................................................... 7-6
What can be done ? ......................................................................................................................................................................... 7-6
How to set up ? ................................................................................................................................................................................ 7-6
Port 2 : Video or S-Video .................................................................................................................................... 7-7
What can be done ? ......................................................................................................................................................................... 7-7
How to configure port 2 ? ................................................................................................................................................................. 7-7
Line Multiplier ..................................................................................................................................................... 7-7
What can be done ? ......................................................................................................................................................................... 7-7
How to select when a line multiplier is built in ? ............................................................................. .................................................. 7-7
Switching the multiplier ON/OFF ..................................................................................................................................................... 7-8
Motion Processing .............................................................................................................................................. 7-8
Why Motion Processing ? ................................................................................................................................................................ 7-8
How to activate ? .............................................................................................................................................................................. 7-8
Output Mode ....................................................................................................................................................... 7-9
What can be done ? ......................................................................................................................................................................... 7-9
How to select a new scan rate ? ..................................................................................................................................................... 7-9
Video Equalizing ................................................................................................................................................. 7-9
What can be done ? ......................................................................................................................................................................... 7-9
How to select Video Equalizing ? ..................................................................................................................................................... 7-9
How to adjust the Video Equalizing ? ............................................................................................................................................. 7-10
Noise Reduction ............................................................................................................................................... 7-10
What can be done ? ....................................................................................................................................................................... 7-10
How to select and adjust the Noise Reduction ? .......................................................................................................................... 7-10
Contrast Enhancement ..................................................................................................................................... 7-10
What can be done ? ....................................................................................................................................................................... 7-10
How to select and adjust the contrast enhancement ? ................................................................................................................ 7-10
5976194 BARCOCINE 9 31012002
i-3
Table of Content
Advanced Settings ............................................................................................................................................ 7-11
How to select the Advanced Settings ? ........................................................................................................................................ 7-11
Time Base Correction .................................................................................................................................................................... 7-11
Luminace Delay .............................................................................................................................................................................. 7-11
Clamp Gating .................................................................................................................................................................................. 7-12
Vertical Sync Reference ................................................................................................................................................................ 7-12
Factory Preset ................................................................................................................................................................................ 7-12
Limo Pro Options ............................................................................................................................................................................ 7-13
Coring ............................................................................................................................................................................................. 7-13
LTI ................................................................................................................................................................................................... 7-13
CTI .................................................................................................................................................................................................. 7-14
Geometry Adjustments ..................................................................................................................................... 7-14
What can be done ? ....................................................................................................................................................................... 7-14
Start Up ........................................................................................................................................................................................... 7-14
Important ........................................................................................................................................................................................ 7-14
Horizontal Phase Adjustment ........................................................................................................................... 7-14
Start Up ........................................................................................................................................................................................... 7-14
Note ................................................................................................................................................................................................ 7-14
How to adjust ? ............................................................................................................................................................................... 7-15
Raster Shift Adjustment ................................................................................................................................... 7-15
What has to be done ? ...................................................................................................................................................................
CAUTION .......................................................................................................................................................................................
Start up ...........................................................................................................................................................................................
Note ................................................................................................................................................................................................
Warning ...........................................................................................................................................................................................
7-15
7-15
7-15
7-15
7-15
Left-Right (east-west) Adjustments ................................................................................................................... 7-16
What can be adjusted ? ................................................................................................................................................................. 7-16
Start up ........................................................................................................................................................................................... 7-16
Note ................................................................................................................................................................................................ 7-16
Which adjustment can be executed ? ........................................................................................................................................... 7-16
How to enter an alignment ? .......................................................................................................................................................... 7-16
Warning ........................................................................................................................................................................................... 7-17
Seagull correction .......................................................................................................................................................................... 7-17
Left Side Correction .......................................................................................................................................... 7-18
What can be done ? .......................................................................................................................................................................
Warning ...........................................................................................................................................................................................
Start Up ...........................................................................................................................................................................................
Left Side Adjustments ....................................................................................................................................................................
7-18
7-18
7-18
7-18
Top-Bottom (north-south) Adjustments ............................................................................................................. 7-19
What can be adjusted ? ................................................................................................................................................................. 7-19
Start Up ........................................................................................................................................................................................... 7-19
Note ................................................................................................................................................................................................ 7-19
Which adjustment can be executed ? ........................................................................................................................................... 7-19
How to enter an alignment ? .......................................................................................................................................................... 7-19
Seagull correction .......................................................................................................................................................................... 7-20
Horizontal Size Adjustment .............................................................................................................................. 7-21
What can be done ? ....................................................................................................................................................................... 7-21
Start up ........................................................................................................................................................................................... 7-21
Hint .................................................................................................................................................................................................. 7-21
Vertical Linearity Adjustment ............................................................................................................................ 7-22
What can be done ? ....................................................................................................................................................................... 7-22
Start Up ........................................................................................................................................................................................... 7-22
Vertical Size Adjustment .................................................................................................................................. 7-22
What can be done ? ....................................................................................................................................................................... 7-22
Start up ........................................................................................................................................................................................... 7-22
Hint .................................................................................................................................................................................................. 7-22
Blanking Adjustments ...................................................................................................................................... 7-23
What can be done ? ....................................................................................................................................................................... 7-23
Start Up ........................................................................................................................................................................................... 7-23
How to adjust the Blanking ? ......................................................................................................................................................... 7-23
Convergence Adjustment .................................................................................................................................. 7-24
What has to be done ? ................................................................................................................................................................... 7-24
Note ................................................................................................................................................................................................ 7-24
Adjustment order ............................................................................................................................................................................ 7-24
Start up ........................................................................................................................................................................................... 7-24
How to adjust ? ............................................................................................................................................................................... 7-25
Focusing ........................................................................................................................................................... 7-25
What can be done ? .......................................................................................................................................................................
Start Up ...........................................................................................................................................................................................
Midpoint Focusing ..........................................................................................................................................................................
Top Image Focusing ......................................................................................................................................................................
Bottom Image Focusing .................................................................................................................................................................
i-4
7-25
7-25
7-26
7-26
7-26
5976194 BARCOCINE 9 31012002
Table of Content
Left Image Focusing ...................................................................................................................................................................... 7-26
Right Image Focusing .................................................................................................................................................................... 7-27
Blue on Source ............................................................................................................................................................................... 7-27
Color Select ...................................................................................................................................................... 7-27
What can be done ? ....................................................................................................................................................................... 7-27
Start Up ........................................................................................................................................................................................... 7-27
SERVICE MODE ................................................................................................................. 8-1
Service mode. ..................................................................................................................................................... 8-1
Start Up ............................................................................................................................................................................................. 8-1
Overview flowchart .......................................................................................................................................................................... 8-1
Projector Set-up ................................................................................................................................................. 8-2
What can be done ? ......................................................................................................................................................................... 8-2
Start up the Projector Set-Up .......................................................................................................................................................... 8-2
Identification ....................................................................................................................................................... 8-2
What can be seen ? ......................................................................................................................................................................... 8-2
How to start up ? .............................................................................................................................................................................. 8-3
Run Time ............................................................................................................................................................ 8-3
What can be displayed ? ..................................................................................................................................................................
Run Time Note ..................................................................................................................................................................................
How to start up ? ..............................................................................................................................................................................
How to Reset the CRT run times ? .................................................................................................................................................
8-3
8-3
8-3
8-3
Change password ............................................................................................................................................... 8-4
What can be done ? .........................................................................................................................................................................
Note ..................................................................................................................................................................................................
How to select ? .................................................................................................................................................................................
How to enter a new password ? ......................................................................................................................................................
8-4
8-4
8-4
8-4
Change Projector Address .................................................................................................................................. 8-4
What can be done ? ........................................................................................................................................... 8-4
How to change that address ? ........................................................................................................................................................ 8-4
Change Baudrate ................................................................................................................................................ 8-5
What can be set up ? ....................................................................................................................................................................... 8-5
How to set up ? ................................................................................................................................................................................ 8-5
Projector warm up .............................................................................................................................................. 8-5
What can be done ? ......................................................................................................................................................................... 8-5
How to select ? ................................................................................................................................................................................. 8-5
Warm up ON/OFF .............................................................................................................................................. 8-6
What can be done ? ......................................................................................................................................................................... 8-6
How to install ? ................................................................................................................................................................................. 8-6
Warm Up Frequency .......................................................................................................................................... 8-6
What can be done ? ......................................................................................................................................................................... 8-6
How to install a warm up frequency ? ............................................................................................................................................. 8-6
Projector Warm Up Time .................................................................................................................................... 8-6
What can be done ? ......................................................................................................................................................................... 8-6
How to program the warm up time ? ............................................................................................................................................... 8-6
Power up mode ................................................................................................................................................... 8-7
What can be done ? ......................................................................................................................................................................... 8-7
How to change the mode ? .............................................................................................................................................................. 8-7
Common Address ............................................................................................................................................... 8-7
What can be done ? ......................................................................................................................................................................... 8-7
Why 2 different common address ? ................................................................................................................................................ 8-7
How to change the common address ? .......................................................................................................................................... 8-7
Memory management ......................................................................................................................................... 8-8
What can be done ? ......................................................................................................................................................................... 8-8
How to select ? ................................................................................................................................................................................. 8-8
Copy a block ...................................................................................................................................................... 8-8
What can be done ? ......................................................................................................................................................................... 8-8
How to copy ? .................................................................................................................................................................................. 8-8
Copy softedge settings ....................................................................................................................................... 8-9
What can be done ? ......................................................................................................................................................................... 8-9
How to copy the softedge settings ? ............................................................................................................................................... 8-9
Deletion of blocks ............................................................................................................................................... 8-9
What can be done ? ......................................................................................................................................................................... 8-9
Deleting block by block ...................................................................................................................................... 8-9
What can be done ? ......................................................................................................................................................................... 8-9
How to delete a Block ? ................................................................................................................................................................... 8-9
Deletion of all blocks ........................................................................................................................................ 8-10
What can be done ? ....................................................................................................................................................................... 8-10
How to delete all blocks ? .............................................................................................................................................................. 8-10
Set to midposition ............................................................................................................................................ 8-10
5976194 BARCOCINE 9 31012002
i-5
Table of Content
What can be done ? ....................................................................................................................................................................... 8-10
How to Start Up ? ........................................................................................................................................................................... 8-10
R & B convergence mid .................................................................................................................................... 8-10
What can be done ? ....................................................................................................................................................................... 8-10
How to set convergence to midposition : ...................................................................................................................................... 8-11
Undo R & B convergence mid ........................................................................................................................... 8-11
What can be done ? ....................................................................................................................................................................... 8-11
How to Undo ? ................................................................................................................................................................................ 8-11
Green convergence mid .................................................................................................................................... 8-11
What can be done ? ....................................................................................................................................................................... 8-11
How to set Green settings to midposition ? .................................................................................................................................. 8-11
Undo green convergence mid ............................................................................................................................ 8-12
What can be done ? ....................................................................................................................................................................... 8-12
How to undo ? ................................................................................................................................................................................ 8-12
Undo Focus to Midposition ............................................................................................................................... 8-12
What can be done ? ....................................................................................................................................................................... 8-12
How to undo the Focus to midposition ? ....................................................................................................................................... 8-12
Focus to Midposition ........................................................................................................................................ 8-12
What can be done ? ....................................................................................................................................................................... 8-12
How to set the Focus settings to midposition ? ............................................................................................................................ 8-12
East-West to Midposition ................................................................................................................................. 8-13
What can be done ? ....................................................................................................................................................................... 8-13
How to set the E-W settings to midposition ? ................................................................................................................................ 8-13
Undo East-West to midposition ........................................................................................................................ 8-13
What can be done ? ....................................................................................................................................................................... 8-13
How to Undo the E-W to midposition ? .......................................................................................................................................... 8-13
North-South settings to Midposition ................................................................................................................. 8-13
What can be done ? ....................................................................................................................................................................... 8-13
How to set the N-S settings to midposition ? ................................................................................................................................ 8-14
Undo North-South setting to midposition .......................................................................................................... 8-14
What can be done ? ....................................................................................................................................................................... 8-14
How to Undo the N-S to midposition ? .......................................................................................................................................... 8-14
Digital Vertical Linearity to Midposition ............................................................................................................. 8-14
What can be done ? ....................................................................................................................................................................... 8-14
How to set the Digital Vertical Linearity to Midposition ? ............................................................................................................... 8-14
Undo Digital Vertical Linearity to Midposition ................................................................................................... 8-15
What can be done ? ....................................................................................................................................................................... 8-15
How to undo the digital vertical linearity to midposition ? .............................................................................................................. 8-15
Digital Horizontal Linearity to midposition ......................................................................................................... 8-15
What can be done ? ....................................................................................................................................................................... 8-15
How to set the Digital Horizontal Linearity to Midposition ? .......................................................................................................... 8-15
Undo Digital Horizontal Linearity to Midposition ............................................................................................... 8-15
What can be done ? ....................................................................................................................................................................... 8-15
How to undo the digital vertical linearity to midposition ? .............................................................................................................. 8-16
Astigmatism midposition .................................................................................................................................. 8-16
What can be done ? ....................................................................................................................................................................... 8-16
How to set the Astigmatism to Midposition ? ................................................................................................................................. 8-16
Undo Astigmatism setting to midposition ......................................................................................................... 8-16
What can be done ? ....................................................................................................................................................................... 8-16
How to undo the Astigmatism settings to midposition ? ................................................................................................................ 8-16
All settings to Midposition ................................................................................................................................ 8-17
What can be done ? ....................................................................................................................................................................... 8-17
How to set to midposition ? ............................................................................................................................................................ 8-17
Undo all settings to midpos .............................................................................................................................. 8-17
What can be done ? ....................................................................................................................................................................... 8-17
How to cancel 'Set to midposition' ? .............................................................................................................................................. 8-17
Common Settings ............................................................................................................................................. 8-18
What can be done ? ....................................................................................................................................................................... 8-18
How to select ? ............................................................................................................................................................................... 8-18
Dynaminc Astigmatism .................................................................................................................................... 8-18
What can be done ? .......................................................................................................................................................................
Start Up ...........................................................................................................................................................................................
How to adjust ? ...............................................................................................................................................................................
Focusing on current source ..........................................................................................................................................................
8-18
8-19
8-19
8-19
Gamma Corrections ......................................................................................................................................... 8-20
Gamma Corrections warning ? ..................................................................................................................................................... 8-20
Start Up ........................................................................................................................................................................................... 8-20
CRT run in cycle ............................................................................................................................................... 8-20
What can be done ? ....................................................................................................................................................................... 8-20
i-6
5976194 BARCOCINE 9 31012002
Table of Content
How to select CRT run in cycle ? .................................................................................................................................................. 8-20
CRT Drive Mode ................................................................................................................................................ 8-21
What can be done ? ....................................................................................................................................................................... 8-21
8-21
Available drive modes .................................................................................................................................................................... 8-21
How to change the drive mode ? ................................................................................................................................................... 8-21
CRT Drive mode warning .............................................................................................................................................................. 8-21
Memory banks .................................................................................................................................................. 8-21
What can be done ? ....................................................................................................................................................................... 8-21
How to select Memory Banks ? .................................................................................................................................................... 8-21
How to create a new memory bank ? ........................................................................................................................................... 8-22
How to recall a specific memorybank for the actual source ? ..................................................................................................... 8-22
Flyback Turnover Point ..................................................................................................................................... 8-22
What can be done ? ....................................................................................................................................................................... 8-22
Set Up of the Flyback Turnover Point ............................................................................................................................................ 8-22
Menu Position .................................................................................................................................................. 8-22
What can be done ? ....................................................................................................................................................................... 8-22
Voltage Diagnostics ......................................................................................................................................... 8-23
What can be seen ? ....................................................................................................................................................................... 8-23
How to start up ? ............................................................................................................................................................................ 8-23
How to change the position ? ........................................................................................................................................................ 8-23
I2C Diagnostics ................................................................................................................................................ 8-23
What can be seen ? ....................................................................................................................................................................... 8-23
How to select ? ............................................................................................................................................................................... 8-23
Projector Diagnostics ....................................................................................................................................... 8-24
What can be seen ? ....................................................................................................................................................................... 8-24
How to display the Projector Diagnostics ? .................................................................................................................................. 8-24
PROGRAMMABLE FUNCTION KEYS ................................................................................. 9-1
Programmable Function Keys ............................................................................................................................ 9-1
What can be done with these keys ................................................................................................................................................. 9-1
How can a Function Key be programmed ? ................................................................................................................................... 9-1
MESSAGES, WARNINGS AND FAILURES ...................................................................... 10-1
ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90 - 99 ............................................ A-1
Adjustment Blocks (memory blocks) ..................................................................................................................A-1
What are adjustment block ? ........................................................................................................................................................... A-1
Built up of block ................................................................................................................................................................................ A-1
Source numbers 90 - 99 ..................................................................................................................................... A-1
Why used ? ...................................................................................................................................................................................... A-1
How to create a second block ? ...................................................................................................................................................... A-1
5976194 BARCOCINE 9 31012002
i-7
Table of Content
i-8
5976194 BARCOCINE 9 31012002
Safety Instructions
1
SAFETY INSTRUCTIONS
Safety Instructions
Notice on Safety
This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology equipment including electrical business equipment.
These safety standards impose important requirements on the use of safety critical components, materials and isolation, in order
to protect the user or operator against risk of electric shock and energy hazard, and having access to live parts.
Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength,
enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment's normal operation
fails.
INSTALLATION INSTRUCTIONS
Before operating this equipment please read this manual thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers.
OWNER’S RECORD
The part number and serial number are located at the back side of the projector. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your BARCO dealer regarding this product.
PART NUMBER :
SER. NUMBER :
DEALER :
Safety indication on the product
The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may
cause a risk of electrical shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating and/or servicing instructions
are included in the technical documentation for this equipment.
5976194 BARCOCINE 9 31012002
1-1
Safety Instructions
Safety Warning
TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Note :
The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022.
* All the safety and operating instructions should be read before using this unit.
* The safety and operating instructions manual should be retained for future reference.
* All warnings on the equipment and in the documentation manuals should be adhered to.
* All instructions for operating and use of this equipment must be followed precisely.
On Safety
1. This product should be operated from an AC power source.
Power input is autoranging from 100 V(-10%) to 240V(+6%).
2. All equipment in the system is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin. This plug will only
fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable. (If the supplied power cable is not the correct one, consult your dealer.)
A. Mains lead (Power cord) with CEE 7 plug:
The wires of the mains lead are colored in accordance with the following code.
Green and yellow: earth (safety earth)
Blue:
neutral
Brown:
line (live)
B. Power cord with ANSI 73.11 plug:
The wires of the power cord are colored in accordance with the following code.
Green/yellow:
White:
Black:
ground
neutral
line (live)
3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
4. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the
extension cord does not exceed the extension cord ampere rating.
5. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked
by qualified service personnel before resuming operations.
6. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the projector due to lightning and AC power-line surges.
1-2
5976194 BARCOCINE 9 31012002
Safety Instructions
Caution on Fire Hazard
Do not place flammable or combustible materials near projector !
BARCO large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector
radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe.
Explosing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that
material, resulting in a fire. For this reason, it is absolutely necessary to leave an "exclusion zone" around all external surfaces of
the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less that 10 cm (4") for
Barco Retro Projectors. Do not cover the projector with any material while the projector is in operation.
Keep flammable and combustible materials away from the projector at all times. Mount the projector is a well ventilated area away
from sources of ignition and out of direct sun light. Never expose the pojector to rain or excessive moisture. In the event of fire,
use sand, CO2, or dry powder fire extinguishers; never use water on anelectrical fire.
Always have service performed on this projector by authorized BARCO service personnel. Always insist on genuine BARCO
replacement parts. Never use non-BARCO replacement parts as they may degrade the safety of this projector.
On installation
1. Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it.
2. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator
or heat register.
The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
4. Do not block the projector cooling fans or free air movement under and around the projector. Loose papers or other objects
may not be nearer to the projector than 4" on any side.
On servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the equipment.
c.If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed.
Note : Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.
Replacement parts - When replacement parts are required, be sure the service technician has used original BARCO replacement
parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions
may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void
warranty.
Safety check - Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
-
-
To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these
will damage the cabinet.
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating,
therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution,
or thinner.
5976194 BARCOCINE 9 31012002
1-3
Safety Instructions
On repacking
Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
In order to obtain the best quality for the projected image, it is essential that the ambient light which is allowed to fall on the screen
be kept to an absolute minimum.
When installing the projector and screen, care must be taken to avoid exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting fixtures.
The use of controlled ambient lighting, such as incandescent spot light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors and walls of the room in which the projector is to be installed are
non-reflecting, dark surfaces. Brighter surfaces will tend to reflect and diffuse the ambient light and hence reduce the contrast of
the projected image on the screen.
Note
Definition
Service personnel: Persons having appropriate technical training and experience necessary to be aware of hazards to which they
are exposed in performing a task and of measures to minimize the danger to themselves or other persons.
1-4
5976194 BARCOCINE 9 31012002
Connections
2
CONNECTIONS
Power Connection to Projector
AC Power (mains) Cord Connection
Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector
at the rear side of the projector.
7
KLV GH Y LFH F RPSOLHV ZLWKSDU W RI
WKH )&& U XOH V 2SHU D WLRQLV VXEM HF WWR
IR O O R Z L Q J WZ R F R Q G L W LR Q V 7K L V
6HHLQ VWDOODWLR QLQ VWUX FWLRQ VE HIR UHFR Q Q HFWLQ JWR WKHVX SS O\
GH Y LFH P D\QRWF D XV H KDU P IXOLQWHU 9R LUODQ RWLFHG
LQ VWDOODWLRQ DY DQ WG HUDFFR UG HUDX UpVHDX IHU H QFH DQGWKLVGH Y LF H PXV W
DF F H SWD Q\LQWHU IH U HQF H U H F H LY H G
LQF OXGLQJLQWH U IH U H QF H WKD WP D\F DXV H
XQGH VLU H GRSH UD WLRQ
9 QRP
,QRP
2))
21
)UHT
9
5
SH U LSKH U DOV
*
%
&RP S+6 \QF 96 \QF
6 9 ,'( 2
2 ))21
$PS
9,'(2
2))2 1
2KP
2KP
+ ]
POWER / MAINS
C OMM. P OR T
P ORT 3
P ORT 4/5
PORT 2
9QRP
,QRP
2))
21
PO W ER
)UHT
P ORT 1
JUHH QRSH UD WLRQ
UH GVWD QGE\
PROJECT OR MODE
9
$PS
+]
/ M A INS
Power Check
The power voltage is autoranging between 100V(-10%) and 240V (+6%).
Switching On/Off
The projector is switched ON and OFF using the power (mains) switch ON/OFF.
Pressed : ON
Not pressed : OFF
The projector can start in the 'operational mode' (image displayed) or in the 'stand by mode', depending on the power up setting in
the service mode.
Stand by indication lamp :
No light up : projector switched off
Green color : projector in Operational mode
Red color : projector is in Standby mode.
7KL V G H Y L F H F RP S O L HV ZL WK S DU W RI
WKH )& & U XO H V 2S HU D WLR Q L V V X EM H FW WR
I RO O R ZL QJ W ZR F RQ GL WL RQ V 7K L V
G HY LF H P D\ Q RW FD XV H K D UP IX O LQ WHU IHU H QF H D QG WK L V G HY L FH P X VW
D FF HS W DQ \ L Q WH U IH U HQ F H U HF HL Y HG L QF O XG L QJ L QWH UIH UH QF H WK DW P D \F D XV H
X QG HV L UH G R S HU DWL R Q
9,'(2
2))21
2KP
POR T 1
JUHHQRSHUDWLRQ
UHGVWDQGE\
PROJECTOR MODE
5976194 BARCOCINE 9 31012002
2-1
Connections
When starting up the projector, with the power switch or via the stand-by key, the projector can start up in two ways if the "CRT run
in" cycle option is switched OFF.
- full white image (projector warm up) or
- immediate image display.
The way of starting up can be set in the service mode.
Source Connections
Input locations
Input facilities
The following source types can be connected to the inputs :
- Composite Video (only in R9002401)
- S-Video (only in R9002401)
- RGBS or RGsB
- RGB3S or RG3sB
- (R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) [component input]
- (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) [component input]
7KLVGHYLFH FRPSOLHVZLWKSDUWRI
WKH)&&UXOH V2SHUDWLRQLVVXEMHFWWR
6HHLQVWDOODWLRQLQVWUXFWLRQVEHI RUHFRQQHFWLQJWRWKHVXSSO\
IR O O R ZL Q J WZR FR Q G L WL R Q V 7K L V
GHYLFHPD\ QRWFDXVHKDUPIXOLQWHU
9RLUODQRWLFHG
LQVWDOODWLRQDY DQWGHUDFFRUGHUDXUpVHDX
IHUHQFHDQG WKLVGHYLFHPXVW
DFFHSWDQ\L QWHUIHUHQFHUHFHLYHG
LQFOXGLQJLQW HUIHUHQFHWKDWPD\FDXVH
XQGHVLUHGR SHUDWLRQ
9QR P
,QRP
2))
21
)UHT
9
$PS
5
SHULSKHUDOV
*
%
& RPS+6\QF96\QF
69,'(2
2))21
9,'(2
2KP
2)) 21
2KP
JUHHQRSHUDW LRQ
UHGVWDQGE\
+]
POWER / MAINS
COMM. PORT
PORT 4/5
PORT 3
3
4
PORT 2
5
2
PO RT 1
PROJECTOR MODE
1
Which source to which input
Image 1 and tabel 1 give an overview of the relation between source type, input terminals and selection key on the RCU.
1
2
3
4
5
*
Input signal Y/C (luma/chroma)
Input signal : R, G and B with automatic sync detection between seperate sync (separate composite sync or with separate
Hor and Vert. sync) or sync on green (composite sync).
Input signal : R-Y, Y and B-Y with separate composite sync or with separate Hor and Vert. sync or with composite sync
on Y.
Input signal : R, G and B with separate Tri level sync or with Tri-level sync on green (optional).
Input signal : R-Y, Y and B-Y with separate Tri level sync or with composite Tri-level sync (optional).
Video or S-Video : switchable in the Picture Tuning menu.
Source No Projector input
Press digit button
1
Comp. Video*
1
2
S-Video/Comp. Video*
2
3
RGB
3
4/5
RGB
4 or 5
4/5
Component video*
6
4/5
RGB with Tri level sync
7
4/5
Component video*
with Tri-level sync
8
*only in R9002401
2-2
5976194 BARCOCINE 9 31012002
Connections
Composite Video source.
Which signals to the Video Input ?
PRO JECTOR MOD E
PORT 2
P OR T 1
PORT 4/ 5
POR T 3
7 KLV
GHY
L FHFRPSOL H
VZL WKSDUW RI
COMM . PORT
POW ER / MA IN S
6HHLQVWD OODWL R
Q LQVWUXFWLRQV EHIRU HFRQ
QHFWL QJ
WRWKHVXSSO\ W KH)&& U
XOHV
2SHUD
W LRQLVV
X EM
HFWW R
9RLUO DQRWLFH G
LQVW DOODWLRQDYD QWGHUDFF RUGHU DXUp VH DX
I ROORZLQJWZRFRQGLW LRQV 7KLV
GHYLFHPD\QRW FDXVHKDUPI X
O LQWHU
I HUHQFH DQG WKLVGHYLFHPX VW
9
9 QR P
2 ))
21
, QR P
$ PS
)U H T
+]
POW ER / M AIN S
5
SHUL SK
HU DOV
CO MM. PORT
P OR T 3
*
%
DFFHSW D
Q \ LQWHU
I HU
HQFHUHFHLYHG
& RP S + 6 \ QF 9 6 \ QF
6 9 ,' ( 2
2 )) 2 1
9 ,' (2
2KP
PORT 4 /5
PORT 2
2 )) 2 1
2KP
POR T 1
JU H H QR S H U D WLR Q
LQ FOXGLQJLQW H
UI HUHQFH WKDWPD\FDXVH
XQGHVLUHGRSHUDWLRQ
U H G V W D QG E\
PROJECTO R M OD E
WRQH[WSURMHFWRU
&RPSRVLWH
RUWRDPRQLWRU
YLGHR
$XGLR2XW
79WXQHUHJ0DUFR3ROR
9&5
Composite video signals from a VCR, OFF air signal decoder, etc..
Video input selection
With the RCU : press digit button 1
Note on Loop-through
When using the loop-through Video output, then set the termination switch to the 'OFF' position.
75 W Termination Switch for Video
Terminate the video input of the projector using the 75 W switch next to the video input, when the projector operates alone or when
the projector is the last unit in loop-through configuration.
The switch is set to 'ON' : signal terminated
The switch is set to 'OFF' : signal not terminated.
S-Video or Video source to port 2
Which Signals to port 2
Input as S-Video input :
Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.
Input as Video input :
Composite video signals from a VCR, OFF air signal decoder, etc..
Pin configuration 4 pin connector
The following pin configuration can be used for S-Video signals and for Video signals.
3
1
2
4
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3:luminance signal(Y)
1Vpp ±3dB
Pin 4:chrominance signal(C)
300mVpp ±3dB
For video:
Pin 1:earth(ground) video
Pin 2:not connected
Pin 3:video signal
Pin 4:not connected
5976194 BARCOCINE 9 31012002
2-3
Connections
PRO JECTO R MOD E
PORT 2
P OR T 1
PO RT 4/ 5
POR T 3
CO MM . PORT
PO W ER / MA IN S
6HHLQVWD OODWL R
Q LQVWUXFWLRQV EHIRU HFRQ
QHFWL QJ
WRWKHVXSSO\ 7 KLV
GHY
L FHFRPSOL H
VZL WKSDUW RI
9RLUO DQRWLFH G
LQVW DOODWLRQDYD QWGHUDFF RUGHU DXUp VH DX
W KH)&& U
XOHV
2SHUD
W LRQLVV
X EM
HFWW R
I ROORZLQJWZRFRQGLW LRQV 7KLV
GHYLFHPD\QRW FDXVHKDUPI X
O LQWHU
I HUHQFH DQG WKLVGHYLFHPX VW
9 QR P
2 ))
21
9
, QR P
$ PS
)U H T
+]
PO W ER / M AIN S
5
SHUL SK
HU DOV
CO MM. PORT
*
P OR T 3
%
DFFHSW D
Q \ LQWHU
I HU
HQFHUHFHLYHG
& RP S + 6 \ QF 9 6 \ QF
PORT 4 /5
6 9 ,' ( 2
2 )) 2 1
9 ,' (2
2KP
2 )) 2 1
2KP
PORT 2
POR T 1
/XP D&K URP D
JU H H QR S H U D WLR Q
U H G V W D QG E\
LQ FOXGLQJLQW H
UI HUHQFH WKDWPD\FDXVH
XQGHVLUHGRSHUDWLRQ
PRO JECTO R M OD E
WRQH[W S UR MHFWR U
RUWR DP R QLWRU
$X GLR 2 XW
9&569+ 6
Input selection port 2
With the RCU, press digit button 2
Input Priority setting
Depending on the priority setting in the 'Picture Tuning menu', Video or S-Video can be displayed.
If the setting is not correct, handle as follow :
1
2
3
Press ADJUST key to start up the adjustment mode. The 'Adjustment main menu' will be displayed (menu 1).
Select 'Random Access'.
Press ENTER to select.
The 'Choose a setup pattern menu' will be displayed (menu 2).
4 Select 'Selected source'.
5 Press ENTER to display the 'Random Access' menu (menu 3).
6 Select 'Picture Tuning'.
7 Press ENTER to display the picture tuning menu (menu 4).
8 Select 'Port2 : Video'.
9 Press ENTER to toggle between VIDEO or S-VIDEO.
10 Press ADJUST to return to operational mode.
ADJUSTMENT MODE
Choose a setup pattern
from below :
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
COLOR BALANCE
SYNC : FAST
PORT2 : VIDEO
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
<ENTER> to accept
<EXIT> to return.
Select a path from below :
RANDOM ACCESS
SERVICE
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Source 01
Source 01
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
menu 3
menu 4
Note on Loop-through
When using the Port 2 loop-through output, set the Termination switch in the 'OFF' position.
75 W Termination Switch for port 2
Terminate the S-Video input of the projector using the 75 W switch next to the S-Video input, when the projector operates alone or
when the projector is the last unit in loop-through configuration.
The switch is set to 'ON' : signal terminated
The switch is set to 'OFF' : signal not terminated.
2-4
5976194 BARCOCINE 9 31012002
Connections
RGB Analog source to port 3
Which signal to port 3
Connect your RGB source with sync on green, composite or separate sync via an interface to Port 3.
Always use an interface when a computer and local monitor have to be connected to the projector as the signal cable coming from
the computer is limited to 60 cm due to interferences.
Pin configuration D9 connector of the Analog input.
Not connected
Ground RGBS
RED
GREEN
BLUE
Ground RGBS
Ground RGBS
Hor/comp. sync
Vert. sync
PORT 2
PRO JECTOR MOD E
P OR T 1
PORT 4/ 5
POR T 3
1
2
3
4
5
6
7
8
9
7 KLV
GHY
L FHFRPSOL H
VZL WKSDUW RI
COMM . PORT
POW ER / MA IN S
6HHLQVWD OODWL R
Q LQVWUXFWLRQV EHIRU HFRQ
QHFWL QJ
WRWKHVXSSO\ W KH)&& U
XOHV
2SHUD
W LRQLVV
X EM
HFWW R
9RLUO DQRWLFH G
LQVW DOODWLRQDYD QWGHUDFF RUGHU DXUp VH DX
I ROORZLQJWZRFRQGLW LRQV 7KLV
GHYLFHPD\QRW FDXVHKDUPI X
O LQWHU
I HUHQFH DQG WKLVGHYLFHPX VW
9 QR P
2 ))
21
9
, QR P
$ PS
)U H T
+]
POW ER / M AIN S
5
SHUL SK
HU DOV
CO MM. PORT
& RP S + 6 \ QF 9 6 \ QF
6 9 ,' ( 2
2 )) 2 1
9 ,' (2
2 )) 2 1
2KP
PORT 4 /5
P OR T 3
$1 $/ 2 *,1 7( 5) 0+]
21
DFFHSW D
Q \ LQWHU
I HU
HQFHUHFHLYHG
%
*
2KP
PORT 2
POR T 1
JU H H QR S H U D WLR Q
LQ FOXGLQJLQW H
UI HUHQFH WKDWPD\FDXVH
XQGHVLUHGRSHUDWLRQ
U H G V W D QG E\
PRO JECTO R M OD E
, 1 38 7
%
+
9
2 ))
5
*
, 13
,1 3
L Q
Y HU
R KPW HUP
Input selection port 3
With the RCU, press digit button 3
RGB Analog source with composite sync to port 4/5.
Which signal to port 4/5
RGB analog input terminals with separate H and V sync inputs, composite sync input or with sync on green (BNC terminals). The
projector detects automatically where the sync signal is located.
PRO JECTO R MOD E
PORT 2
P OR T 1
PO RT 4/ 5
POR T 3
7 KLV
GHY
L FHFRPSOL H
VZL WKSDUW RI
CO MM . PORT
PO W ER / MA IN S
6HHLQVWD OODWL R
Q LQVWUXFWLRQV EHIRU HFRQ
QHFWL QJ
WRWKHVXSSO\ W KH)&& U
XOHV
2SHUD
W LRQLVV
X EM
HFWW R
I ROORZLQJWZRFRQGLW LRQV 7KLV
9RLUO DQRWLFH G
LQVW DOODWLRQDYD QWGHUDFF RUGHU DXUp VH DX
GHYLFHPD\QRW FDXVHKDUPI X
O LQWHU
I HUHQFH DQG WKLVGHYLFHPX VW
9 QR P
, QR P
2 ))
21
)U H T
PO W ER / M AIN S
9
$ PS
5
SHUL SK
HU DOV
%
*
DFFHSW D
Q \ LQWHU
I HU
HQFHUHFHLYHG
& RP S + 6 \ QF 9 6 \ QF
6 9 ,' ( 2
2 )) 2 1
2KP
9 ,' (2
2 )) 2 1
2KP
JU H H QR S H U D WLR Q
LQ FOXGLQJLQW H
UI HUHQFH WKDWPD\FDXVH
XQGHVLUHGRSHUDWLRQ
U H G V W D QG E\
+]
CO MM. PORT
PORT 4 /5
P OR T 3
21
$1$/2* ,17 (5) 0+ ]
,1 387
%
PORT 2
+
POR T 1
PRO JECTO R M OD E
9
2))
5
*
,1 3
R
K P WH
UP
,1 3
LQ YHU
RGBS or RGsB input selection
With the RCU, press digit button 4 or 5.
4 when sync on green.
5 when separate sync
5976194 BARCOCINE 9 31012002
2-5
Connections
RGB Analog source with Tri-level sync to port 4/5.
Which signal to port4/5
RGB analog input terminals with Tri level sync input or with Tri-level sync on green (BNC terminals). The projector detects automatically
where the sync signal is located.
RGB3S or RG3sB input selection
With the RCU, press digit button 7
Component source to port 4/5.
Which signal to port 4/5
(R-Y)Y(B-Y) analog input terminals with sync input or with sync on the luminance (Y) input (BNC terminals). The projector detects
automatically where the sync signal is located.
Component video input selection
With the RCU, press digit button 6
RS232 Connection
RS232 input and RS232 output of the projector.
The projector is equipped with a RS232 port that allows them to communicate with a computer.
Applications
a) remote control:
- easy adjustment of the projector via a computer.
- allow storage of multiple projector configurations and set ups.
- wide range of control possibilities.
- address range from 0 to 255.
b) data communications:
- sending data to the projector or copying the data from the projector to a hard memory device.
Set up of the Baud Rate for Communication with a Computer.
See 'Changing the baud rate' in chapter 'Service mode'.
Communication port for communication with peripherals
Connecting a RCVDS 05 switcher to the projector.
-
2-6
Up to 10 inputs (20 inputs when video and S-video) with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers
are linked via the 5-cable output modules.
Serial communication with the projector.
Remote control buttons on the RCVDS to control the projector (source selection and analog settings)
The selected source number will be displayed on a 2 digit display and the selected input modules will be indicated with a LED
on the rear.
5976194 BARCOCINE 9 31012002
Getting Started
3
GETTING STARTED
Remote Control & Local Keypad
Battery Installation in the RCU
Two batteries are packed together with the RCU. Before using your RCU, install first these batteries.
1
2
3
4
Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU.
Lift up the top side of the cover at the same time.
Insert the batteries as indicated in the RCU.
Put the battery cover on its place.
How to replace the batteries in the RCU ?
To replace the batteries :
1
2
3
4
5
6
7
Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU.
Lift up the top side of the cover at the same time.
Push on the + side of the battery towards the - side
Lift up the battery at the same time.
Repeat for the second battery.
Insert the batteries as indicated in the RCU (battery type AA or LR6 or equivalent).
Put the battery cover on its place.
Note, only important if more than one projector is installed in the room :
1. the default address is zero (0) or (1). The standard RCU is setup for common address zero. To change the common address of
the RCU, contact a BARCO service center. If it is necessary to program the projector address into the RCU, see 'Projector Address'.
2. projector address has to be reprogrammed everytime the battery is changed, the RCU will always switch to the default address.
5976194 BARCOCINE 9 31012002
3-1
Getting Started
Overview of Functions
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely.
This remote control is used for source selection, control, adaptation and set-up. It includes automatic storing of :
- picture controls (Brightness, Sharpness,....)
- settings
Other functions on the control units are:
- switching between standby and operational modes
- switching to "pause" (blanked picture, full power for immediate restarting)
- direct access to all connected sources
- variable adjustment speed : when pushing continuously on the arrow keys or the picture keys, the adjustment will be executed
in an accelerated fashion.
)
)
)
)
)
$'-
(;,7
(17(5
3$86(
7(;7
6+$531
7,17
&2/25
%5,*+71
&2175
3+$6(
75(%/(
%$/$1&(
%$66
92/
stand-by
pause/park
sharpness
tint
color
brightness
contrast
1
Function keys : user programmable keys with functions for direct access.
2
ADJ. : ADJUST key, to enter or exit the adjustment mode.
3
Address key (recessed key), to enter the address of the projector (between 0 and 9). Press the recessed address key with a pencil,
followed by pressing one digit button between 0 and 9.
4
Selection key : no function for this projector
5
PAUSE : to stop projection for a short time, press 'PAUSE'. The image disappears but full power is retained for immediate
restarting.
6
STBY : stand-by button, to start projector when the power switch is switched on and to switch off the projector without switching
off the power switch.
7
Mute : no function in this projector
8
Help : on line help information (not yet available)
9
Digit buttons : direct input selection.
10 Audio controls : no function
11 Picture controls : use these buttons to obtain the desired picture analog level.
12 PHASE : not used.
3-2
5976194 BARCOCINE 9 31012002
Getting Started
13 FREEZ : press to freeze the projected image.
14 TEXT : when adjusting one of the image controls, e.g. contrast, during a meeting, the displayed bar scale can be removed by
pressing 'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again.
15 ENTER : to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.
16 Cursor Keys : to make menu selections when in the adjustment mode.or to increase or decrease the analog level of the image
controls when they are first selected.
17 EXIT : to leave the adjustment mode or to scroll upwards when in the adjustment mode.
18 RC operating indication : lights up when a button on the remote control is pressed. (This is a visual indicator to check the
operation of the remote control)
Operating the Projector
Switching on
Use the power switch to switch on.
When not pressed, the projector is switched off.
When pressed, the projector is switched on.
When switching on with the power switch, the projector can start now in :
- Operational mode (picture displayed)
- Stand by mode
The way of start up depends on the 'Power up' setting in the service mode.
Start up in Operational Mode
The projector can start up with the selected source or
the projector can start up with a warm up cycle message (menu 1).
When this warm up cycle message appears on the screen, the menu offers the possiblity to start with a x minutes taking warm up
periode (press ENTER) or to skip this cycle (press EXIT). The x minutes and the horizontal frequecy can be programmed in the 'Service
mode' under the item 'Projector Set Up'.
Note : This warm up periode is built in so that the projector can reach its maximum specifications and minimize all distortions.
When starting this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in. Every 30 seconds a text box
will be displayed on another place on the screen with the remaining time to go.
The image dimensions can be adjusted with the cursor keys to avoid scanning on the edges of the CRT's.
PROJECTOR WARM UP
A FULL WHITE PATTERN WILL BE
GENERATED FOR x MIN.
FOR IMMEDIATE USE OF THE
PROJCTOR, PRESS <EXIT>
WARNING : SKIPPING THIS
PROCEDURE CAN REDUCE THE
INITIAL PICTURE QUALITY OF THE
PROJECTED IMAGE;
YOU CAN ADJUST THE IMAGE
DIMENSTIONS WITH THE ARROW
KEYS TO AVOID SCANNING ON THE
EDGES OF THE CRT'S;
THIS OPTION CAN BE DISABLED IN
THE SERVICE MENU
with <ENTER>
<EXIT> to return
menu 1
To interrupt the warm up period, handle as follow :
1
Press EXIT, the warm up menu will be redisplayed with the remaining time indication.
2
Press EXIT again to quit the warm up cycle and to display the source.
Start up in Stand by Mode
The projector starts up in stand by.
Press a digit key corresponding to the desired source or press STBY key.
The projector displays the selected source or the warm up cycle message.
When this warm up message appears on the screen, handle as described in 'Start up in Operational Mode'.
Stationary Image Warning
Do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the CRT's.
5976194 BARCOCINE 9 31012002
3-3
Getting Started
RCU Commands to the Projector
Pointing the RCU to the reflective screen
Point the front of the RCU to the screen surface.
Ceiling
IR sensor
Screen
RCU
Point the front of the RCU towards one of the IR sensors in the projector.
Front of projector
Rear side of projector
1
, 7
8
2
6
5
(
6
75
2
5
,5
0
(
5
5
6
5
6
,1
,5
2
(
8
0
7
27(
6R
HLH
LQ
W
DW
OO
DH
WG
LR
Q
Q
VW
UX
R
QY
VDQ
EH
RU
H
FR
Q
Q
HF
W
LQ
U
WR
WK
HV
SS
O\
9
U
ODV
Q
R
LF
LL
Q
V
WD
OO
DF
W
LWL
RQ
D
W
I
GH
U
DF
F
R
UG
H
U
DJ
X
pV
HDX
X
2
)
)2
1
9
Q
R
P
,Q
R
P
)
U
HT
P
O
WERM
/
A
NS
I
45°
)
C
OMM. P
OR
T
PO
R T
3
*
%&
R
P
S
+
6
\Q
F9
6
\
Q
F
2K
P
)
)
)
$'-
3$ 86 (
7 ,17
3$86(
7( ;7
3+$6 (
RCU
7 ,1 7
& 2/25
& 2/25
% 5,*+ 71
75(% /(
%$ 66
2
K
P
(;,7
7KLV G
HY
LF F
HRPS
O LH
Z WLK 3
V
D WU RI
2S
H
UD
WL R
LVV
Q
XE
MH F
WR
IROO
RZ
LQJW Z
R FRQG
LW R
L QV
7
KV
L
WK
5
&&
OX HV
G
HY
LFH)
H
P
D
\Q
RX
WF
D
V
HK
DP
UIX
O LQ
WH
U
UH
H
Q
R
SH
DWLR
U
Q IHUH
QFHD
Q G W K
LVG
HY
LF H
PX
VW
2
)
)
2
1 J
D
FFHS
W D
Q \L Q
WH
UI
H UHQ
F
H UHF
HY
LH G
U
HG
VWD
Q
G
E
\
LQF
OXG
LQJ
LQWHUI
H UH
QF
WKD
H
WPD
\ FD
XV
H
P
ROE
JC T
O
R M
OD
E
X
QG
HV
LU H
G
R
SH
UD
WL
RQ
( 17 (5
3+$6 (
6 +$ 5 31
P
O
R T
1
)
$'-
7( ;7
9
,'
(2
)
)
( ;,7
( 17 ( 5
2
))
2
1
PORT2
45°
)
)
6
9
,'
(
2
PORT4/5
45°
45°
)
5
S
H
LS
U
H
K
UD
OV
9
$
P
S
+
]
& 21 75
6 +$ 5 3 1
%5 ,*+7 1
& 21 75
% $ /$ 1& (
75(% /(
% $/$1 & (
9 2/
% $ 66
9 2/
When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control
unit and the projector's IR sensor.
RCU used in a hardwired configuration.
56 ,1 56 287
,5
1
, 65 78 2
65 5
,
3-4
5(027(
(7 20(5
5976194 BARCOCINE 9 31012002
Getting Started
Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the rear panel
of the projector labelled 'REMOTE'.
Projector address
Why a projector address ?
As more than one projectorcan be installed in a room, the separate projectors should be separately addressable with a RCU or a
computer. So each projector has its own address.
Set up an Individual Projector Address
The set up of a projector address can be done via the software.
See 'Change Projector Address' in Chapter 'Service Mode'
How to control the projector or projectors ?
The projector's address may be set to any value between 0 and 255 which can be set in the Service Mode.
When the address is set, the projector can be controlled now with:
- the RCU for addresses between 0 and 9.
- the Computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
Note : A projector will respond to a RCU set to the common address ('0' or '1') regardless of what address is set in the projector itself.
Common Address
Every projector has a common address '0' or '1'. The choice between '0' and '1' can be selected in the Service mode.
Before using the RCU
The RCU is default programmed with address 0 or 1, 'common address'. With that 'common address' programmed into the RCU, every
projector, with the same common address set up, will listen to the commands given by this RCU. If it is necessary to control a specific
projector, than enter the projector address into the RCU (only when that address is between 0 and 9). The projector with the
corresponding address will listen to that specific RCU.
Display the Projector Address on the Screen.
Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box' (menu 1).
This text box disappears after a few seconds.
PROJECTOR ADDRESS
001
To continue using the RCU with that specific address, it is necessary to enter the same address with the digit buttons (address between
0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 003, then press
"3" digit button on the RCU to set the RCU's address to match the projector's address. Do not press 003 digits. This will address the
remote control to '0' and control all projectors in the room.
If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and control all projectors in the
room.
How to program an address into the RCU?
Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons within 5 seconds after
pushing the address key. That address can be any digit between 0 and 9.
5976194 BARCOCINE 9 31012002
3-5
Getting Started
Controlling the Projector
Input selection modes
Source No Projector input
Press button
1
Comp. Video
1
2
S-Video/Comp. Video
2
3
RGB
3
4/5
RGB (HV, SOG)
4 or 5
4/5
Component Video
6
4/5
RGB with Tri level sync 7
4/5
Component Video with
Tri-level sync
8
Input Selection via the RCU.
With the digit buttons, it is possible to select one of the above input modes.
When the source is selected
When a valid and available source is selected, there will be information displayed on the screen about that source. This information
includes :
- Source number
- Horizontal frequency
- Vertical frequency
Source 02
Fh= 15.6 kHz
Fv= 50 Hz
When the entry is a non valid source number, a warning appears on the screen : 'input not available'.
WARNING
input not
available
When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the
source becomes available. A message 'source not available' will be displayed for a short time.
WARNING
source not
available
When a Video or S-Video source is selected and no decoder is installed, the projector displays the folllowing message : 'Option not
installed'.
WARNING
Option not
installed !
3-6
5976194 BARCOCINE 9 31012002
Getting Started
Picture controls
The control keys are located on the right side of the key panel of the RCU and indicated with the name of the control and an icon.
When an image control is pressed, a text box with bar scale and the function name of the control, e.g. 'brightness...' appears on the
screen (only if text is ON). The length of the bar scale indicates the current memorized setting for this source. The bar scale changes
as the + or - side of the button of the control are pressed.
Brightness Control
A correct 'brightness' setting is important for good image reproduction. Adjust the brightness with the + button and - button until the
darkest parts of the picture appear black.
A bar scale gives a visual indication on the screen of the current brightness setting while pressing on the above indicated buttons.
If the bar scale is not visible on the screen, press 'TEXT' once and retry the above indicated buttons.
The bar scale increases when pressing on the + button (higher brightness) and decreases when pressing on the - button (lower
brightness).
Contrast Control
A correct 'contrast' setting is important for good image reproduction.
Adjust the contrast to the level you prefer, according to room lighting conditions.
A bar scale gives a visual indication on the screen of the current contrast setting while pressing the + or - buttons . If the bar scale
is not visible on the screen, press 'TEXT' key once and retry the above indicated buttons.
The bar scale increases when pressing on the + button (higher contrast) and decreases when pressing on the - button (lower contrast).
Color Saturation Control
Color saturation is only active for Video and S-Video. Adjust the color saturation using the + and - buttons . A bar scale gives a visual
indication on the screen of the current color setting while pressing on the above indicated buttons. If the bar scale is not visible on
the screen, press 'TEXT' key once and retry the above indicated buttons. The bar scale increases when pressing on the + button (richer
colors) and decreases when pressing the - button (lighter colors).
Tint Control
Tint is only active for Video and S-Video. Tint control is effective only when using the NTSC 4.43 or NTSC 3.58 system. A bar scale
gives a visual indication on the screen of the current tint setting while pressing the + or - buttons . If the bar scale is not visible on the
screen, press the 'TEXT' key once and retry the above indicated buttons.
The bar scale increases when pressing on the + button and decreases when pressing the - button.
Sharpness Control.
Sharpness control only active for Video and S-Video. A bar scale gives a visual indication on the screen of the current sharpness setting
while pressing the + or - buttons. If the bar scale is not visible on the screen, press 'TEXT' key once and retry the above indicated
buttons.
The bar scale increases when pressing on the + button (sharper picture) and decreases when pressing on the - button (softer picture).
Sound controls
These keys have no function with this projector.
The Pause key.
When the Pause key is pressed, the image projection is stopped but the projector remains with full power for immediate restart.
To restart the image :
1 Press the Pause key,
2 Select a source number.
The Freeze key.
When the Freeze key is pressed, the image is frozen until this key is pressed again.
5976194 BARCOCINE 9 31012002
3-7
Getting Started
3-8
5976194 BARCOCINE 9 31012002
Start up Adjustment mode
4
START UP OF THE ADJUSTMENT MODE
Adjustment Mode
Start Up
All picture adjustments are made while in the 'Adjustment mode'.
Press the ADJUST key.
The projector displays the 'Main menu' (menu 1).
MAIN MENU
Image Control
IRIS Control
Sound Control
Function keys
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
You are now in the 'Adjustment mode'. The cursor keys are used to make menu selections and also vertical and horizontal adjustments.
The ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used
to terminate the adjustment mode while a path selection menu (head menu) is displayed.
Possible Paths
Depending on the projector configuration the following paths are possible with the 'Main menu'.
Image Control - Allows to change the color temperature of the image and to select another format (adjustment) for the image.
IRIS-Control - This control allows to align the projector automatically using the autoconvergence unit IRIS built into the projector.
Sound Control - Allows to select the sound mode (only when a sound unit is built in).
Function Keys - Gives an overview of the programmed function for each key.
Service Menus - Installation and adjustment menus to set up the projector. Before entering a warning will be displayed.
5976194 BARCOCINE 9 31012002
4-1
Start up Adjustment mode
4-2
5976194 BARCOCINE 9 31012002
Main Menu
5
MAIN MENU
Main Menu
Overview Flowchart
COLOR ADJUST
IMAGE CONTROL
FORMAT SELECT
IRIS TOUCH UP
IRIS CONTROL
IRIS AUTO CONVERGE
IRIS FULL ALIGNMENT
NORMAL STEREO
SPATIAL STEREO
SOUND CONTROL
PSEUDO STEREO
MAIN MENU
MONO
F1
F2
FUNCTION KEYS
F3
F4
F5
IRIS
GUIDED
SERVICE MENUS
RANDOM ACCESS
INSTALLATION
SERVICE
5976194 BARCOCINE 9 31012002
5-1
Main Menu
Image Control
Starting Up
1
2
Push the cursor keys é or ê to select 'Image Control' (menu 1).
The selected item will change in color and a marker will be displayed in front of it.
Press ENTER to select.
The 'Image Control' menu will be displayed (menu 2a or 2b).
MAIN MENU
IMAGE CONTROL
Image Control
IRIS Control
Sound Control
Function keys
Image Processing
Color Adjust
Format Select
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2a
Line Multiplier
Why Line Multiplying
If a line multiplier is built in and in the ON state, video images can be displayed with different line and frame rates. That will improve
the video image quality.
How to change the Multiplier Setting
To set up the LIMO functions, handle as follow :
1
2
Push the cursor keys é or ê to select 'Image Processing' (menu 1)
Press ENTER to select the 'Image Processing' menu.
The Image Processing menu will be displayed (menu 2).
IMAGE CONTROL
IMAGE PROCESSING
Image Processing
Color Adjust
Format Select
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
Video Equalizing
Noise Reduction
Contrast Enhancement
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
Line Multiplier ON/OFF
To switch the line multiplier on/off, handle as follow :
1 Push the cursor keys é or ê to select 'Line Multiplier' (menu 1)
2 Press ENTER to toggle between ON and OFF.
When in the ON state, all multiplier functions are selectable.
IMAGE PROCESSING
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
Video Equalizing
Noise Reduction
Contrast Enhancement
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5-2
5976194 BARCOCINE 9 31012002
Main Menu
Multiplier Mode
What can be selected within the multiplier mode ?
The multiplier menu makes it possible to select different scan rate for the connected video signal.
How to start up the Multiplier Mode menu ?
1
2
Push the cursor keys é or ê to select 'Multiplier Mode' (menu 1).
Press ENTER to select and to display the Multiplier Mode menu (menu 2a or menu 2b)
Depending on the frequency of the input source, menu 2a or menu 2b will be displayed.
MULTIPLIER MODE
MULTIPLIER MODE
IMAGE PROCESSING
50 Hz
100 Hz
50 Hz
100 Hz
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
625 lines
625 lines
1250 lines
1250 lines
P
P
P
I
60 Hz
120 Hz
60 Hz
120 Hz
525 lines
525 lines
1050 lines
1050 lines
P
P
P
I
Video Equalizing
Noise Reduction
Contrast Enhancement
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2a
menu 1
menu 2b
How to change the scan rate ?
1
2
Push the cursor keys é or ê to select a new scan rate (menu 1).
Press ENTER to activate this scan rate.
e.g. 100 Hz 625 lines P ==>
Vertical frequency of the image : 100 Hz
Quantity of horizontal lines : 625 lines
Interlace mode : P = Non-interlaced image (progressive scan).
MULTIPLIER MODE
50 Hz
100 Hz
50 Hz
100 Hz
625 lines
625 lines
1250 lines
1250 lines
P
P
P
I
Select with é or ê
then <ENTER>
<EXIT> to return.
Motion Processing
Why Motion Processing ?
With this function it is possible to recognize whether the source material was originally film or video. That prevents the creation of
motion artifacts.
How to activate ?
1
2
Push the cursor keys é or ê to select 'Motion Processing' (menu 1).
Press ENTER to toggle between ON and OFF.
IMAGE PROCESSING
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
Video Equalizing
Noise Reduction
Contrast Enhancement
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
5-3
Main Menu
Video Equalizing
What can be done ?
The shapness of the image can be adjusted for 3 frequency ranges (low, medium and high) separately.
To make it a little bit easy, 7 pre-programmed factory presets are available. The customer is also free to adjust its own sharpness
for the 3 ranges.
How to select Video Equalizing ?
1
2
Push the cursor keys é or ê to select 'Video Equalizing' (menu 1).
Press ENTER to display the adjustment menu (menu 2).
How to adjust the Video Equalizing ?
1
2
Push the cursor keys ç or è to select 'Low' or Mid' or 'HI.' or 'Factory Preset : x'
Push the cursor keys é or ê to adjust the sharpness in the choosen band (low, mid, high) or to scroll through the factory preset
IMAGE PROCESSING
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
LOW
MID
HI.
FACTORY PRESET : x
Video Equalizing
Noise Reduction
Contrast Enhancement
Select with ç or è
Adjust or scroll presets
with é or ê
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
menu 1
(x = 1 to 7).
Factory preset 8 is equal to the custom adjustment as made with low, mid and high.
Noise Reduction
What can be done ?
Noisy, lower quality video images can be ameliorated by use of the Noise Reduction feature.
How to select and adjust the Noise Reduction ?
1
2
3
4
Push the cursor keys é or ê to select 'Noise Reduction' (menu 1).
Press ENTER to display the adjustment text box (menu 2).
Push the cursor keys é or ê to adjust the noise.
Press ENTER to return to the 'Image Processing' menu.
IMAGE PROCESSING
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
Video Equalizing
Noise Reduction
Contrast Enhancement
Dynamic
Noise Reduction
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Off
Max
menu 2
Contrast Enhancement
What can be done ?
Enhancing the contrast results in a more dynamic image.
5-4
5976194 BARCOCINE 9 31012002
Main Menu
How to select and adjust the contrast enhancement ?
1
2
3
4
Push the cursor keys é or ê to select 'Contrast Enhancement' (menu 1).
Press ENTER to display the adjustment text box (menu 2).
Push the cursor keys é or ê to adjust the contrast.
Press ENTER to return to the 'Image Processing' menu.
IMAGE PROCESSING
Line Multiplier : ON
Multiplier Mode
Motion Processing : ON
Video Equalizing
Noise Reduction
Contrast Enhancement
Contrast
Enhancem.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
-3
0
+3
menu 2
Color Adjust
What can be done ?
The color temperature of the image can be installed. The customer has the choise between 4 factory preset color temperatures
and one custom. This custom color temperature has to be adjusted in the 'Random Access Adjustment Mode'.
How to select 'Color Adjust' and to select a new color temperature?
1
2
3
4
Push the cursor keys é or ê to select 'Color Adjust' (menu 1).
Press ENTER to display the Color Adjust menu (menu 2).
Push the cursor keys é or ê to select the desired color temperature.
Press ENTER to activate that color temperature.
IMAGE CONTROL
COLOR ADJUST
Image Processing
Color Adjust
Format Select
Broadcast
Film
Video
Computer
Custom
3200
4900
6500
9300
°K
°K
°K
°K
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 1
Format Select
What can be done ?
For one source, up to 8 different sets of settings can be stored. A set of settings is called 'Format'. A 'Format' can be 'available'
or 'free'.
'Available' when settings are stored in this location.
'Free' when no setting are stored in this location. This location can be used for storing new adjustment settings for this source.
When 'available', a name of 8 characters can be programmed by the user.
How to select a 'Format' ?
1
2
3
4
Push the cursor keys é or ê to select 'Format Select' (menu 1).
Press ENTER to display the Format List (menu 2).
Push the cursor keys é or ê to select the desired 'Format'.
Press ENTER to select.
IMAGE CONTROL
Image Processing
Color Adjust
Format Select
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Format
Format
Fromat
Format
Format
Format
Format
Format
FORMAT LIST
Source 01
VIDEO
Available x x x x x x x x
Free
xxxxxxxx
Available x x x x x x x x
Free
xxxxxxxx
Free
xxxxxxxx
Free
xxxxxxxx
Free
xxxxxxxx
Free
xxxxxxxx
1
2
3
4
5
6
7
8
Select with é or ê
<ENTER> to select
<EXIT> to return
<TEXT> to enter a name
menu 2
5976194 BARCOCINE 9 31012002
5-5
Main Menu
How to add a name to a 'Format' ?
1
2
3
4
5
6
Push the cursor keys é or ê to select the Format to which a name has to be added (menu 1).
Press TEXT to display the compose menu (menu 2).
The position of the character which will be edited, will be indicated with a digit. Push the cursor keys é, ê, ç or èto select
the first character.
Press ENTER to select the choosen character. This character will be inserted on the indicated position. The 'edit character'
indication will be incremented with one.
Continue in the same way for the other characters.
When the name is completed, press EXIT to return to the 'Format List' menu (menu 3).
Format
Format
Fromat
Format
Format
Format
Format
Format
FORMAT LIST
Source 01
VIDEO
Available x x x x x x x x
Free
xxxxxxxx
Available x x x x x x x x
Free
xxxxxxxx
Free
xxxxxxxx
Free
xxxxxxxx
Free
xxxxxxxx
Free
xxxxxxxx
1
2
3
4
5
6
7
8
COMPOSE
A
J
S
\
0
B
K
T
:
1
C
L
U
2
D
M
V
E
N
W
F
O
X
G
P
Y
H
Q
Z
I
R
3
4
5
6
7
8
9
xxxxxxxx
Format
Format
Fromat
Format
Format
Format
Format
Format
FORMAT LIST
Source 01
VIDEO
1 Available x x x x x x x x
2 Free
xxxxxxxx
3 Available BARCO
4 Free
xxxxxxxx
5 Free
xxxxxxxx
6 Free
xxxxxxxx
7 Free
xxxxxxxx
8 Free
xxxxxxxx
Edit character 1
Select with é or ê
<ENTER> to select
<EXIT> to return
<TEXT> to enter a name
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return
menu 2
Select with é or ê
<ENTER> to select
<EXIT> to return
<TEXT> to enter a name
menu 3
How to store the settings to a new 'Format' ?
1
2
3
4
Push the cursor keys é or ê to select a free format.
Press ENTER to activate.
Make any adjustment to the image.
Quit the adjustment mode by pressing ADJUST.
The selected format will change from free to available.
IRIS control
With the IRIS functions it is possible to ameliorate the convergence and alignment of the image.
Start Up
1
2
Push the cursor keys é or ê to select 'IRIS control' (menu 1).
The selected item will change in color and a marker will be displayed in front of it.
Press ENTER to select.
The 'IRIS control' menu will be displayed (menu 2).
MAIN MENU
IRIS CONTROL
Image Control
IRIS Control
Sound Control
Function keys
IRIS Touch Up
IRIS Auto Converge
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
Note
Before starting one of the IRIS functions, be sure the projector has warmed up for at least 20 min. Only after 20 min the projector
has reached its full specifications.
IRIS Touch Up
What can be done ?
If you discover in the middle of the image a convergence misalignment between red, green and blue, the static convergence of this
currently selected source can be adjusted with the touch up function.
5-6
5976194 BARCOCINE 9 31012002
Main Menu
How to start up the IRIS Touch Up ?
1
2
Push the cursor keys é or ê to select 'IRIS Touch Up' (menu 1).
Press ENTER to activate the touch up function.
The process starts and when successfully completed, the projector will return to image display of the current source.
IRIS CONTROL
IRIS Touch Up
IRIS Auto Converge
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
IRIS Auto Converge
What can be done ?
The autoconvergence on the current source will be carried out automatically, starting from the existing settings. By projecting
alternately red and blue lines, 25 convergence areas are aligned onto the green pattern.
How to start up the IRIS Auto Converge ?
1
2
Push the cursor keys é or ê to select 'IRIS Auto Converge' (menu 1).
Press ENTER to activate the autoconvergence function.
The process starts and when successfully completed, the projector will return to image display of the current source.
IRIS CONTROL
IRIS Touch Up
IRIS Auto Converge
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
5-7
Main Menu
Sound Control
What can be done ?
When the sound option is available, the following sound modes can be selected : normal stereo, spatial stereo, pseudo stereo or
mono.
How to start up and to select the Sound Control ?
1
2
3
4
Push the cursor keys é or ê to select 'Sound Control' (menu 1).
Press ENTER to select the Sound Control function.
The Sound Control menu will be displayed (menu 2).
Push the cursor keys é or ê to select the desired sound mode (menu 2).
Press ENTER to activate the chosen sound mode.
MAIN MENU
SOUND CONTROL
Image Control
IRIS Control
Sound Control
Function keys
Select sound mode :
Normal Stereo
Spatial Stereo
Pseudo Stereo
Mono
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
Function Keys
What can be done ?
Quick access keys to customer pre-programmed adjustments. Almost any adjustment can be added to a function key. To program
a function key, it is necessary to enter into the 'Service Menu'. To activate a function key, just press the corresponding key.
The following functions are factory pre-programmed :
F1 = IRIS Touch up
F2 = Convergence Red on Green
F3 = Convergence Blue on Green
F4 = H & V Size
F5 = Color Balance
How to get an overview of the programmed keys ?
1
2
3
Push the cursor keys é or ê to select 'Function Keys' (menu 1).
Press ENTER to display an overview of the function keys (menu 2).
Press EXIT to return.
MAIN MENU
Image Control
IRIS Control
Sound Control
Function keys
FUNCTION KEYS
F1
F2
F3
F4
F5
:
:
:
:
:
IRIS Touch-up
Convergence Red on Green
Convergence Blue on Green
H & V Size
Color Balance
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
<EXIT> to return.
menu 2
Service Menus
What can be done ?
With the complete set of Service menus such as IRIS, Guide, Random Access, Installation and Service it is possible to adjust the
projector completely.
When entering the Service Menus, a warning will be displayed mentioning that only qualified service personnel may enter the Service
menus.
5-8
5976194 BARCOCINE 9 31012002
Main Menu
How to enter the Service Menu ?
1
2
3
Push the cursor keys é or ê to select 'Service Menus' (menu 1).
Press ENTER to select.
A warning will be displayed (menu 2). "Risk of incorrect adjustment of the projector. The following SERVICE menus are reserved
to and to be performed only by qualified personnel ! If qualified, press <ENTER> to continue, or if not, <EXIT> to return.
If qualified, press ENTER (menu 3).
If not qualified, press EXIT
MAIN MENU
Image Control
IRIS Control
Sound Control
Function keys
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE
PROJECTOR.
ADJUSTMENT MODE
Select a path from below :
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Source 01
Select with é or ê
then <ENTER>
<EXIT> to return.
The following
SERVICE menus
are reserved to,
and to be performed only
by qualified personnel !
If qualified, press
<ENTER> to continue, or
if not, <EXIT> to return.
menu 3
menu 2
5976194 BARCOCINE 9 31012002
5-9
Main Menu
5-10
5976194 BARCOCINE 9 31012002
Entering the Service Menus
6
ENTERING THE SERVICE MENUS
Service menus
What is available in the Service menus ?
A complete set of adjustments divided in different modes are available to adjust the projector
The different mode are :
IRIS : to autoalign and autoconverge the projector.
Guided : Guided should be selected if the user intends to perform a complete alignment of the projected image. All the necessary
geometry and convergence adjustments are executed in a predetermined sequence.
Random Access : Random Access should be selected if the user intends to make only a few adjustments or if the user is highly
qualified and knows the sequence of adjustments.
Installation : Installation should be selected if the projector has been relocated and/or a different screen size is desired.
Service : Service should be selected if the user intends to change predefined settings.
How to enter the Service Menus ?
1
2
3
4
Press the ADJUST key.
The projector displays the 'Main menu' (menu 1).
Push the cursor keys é or ê to select 'Service Menus'
Press ENTER to select.
A warning will be displayed (menu 2).
If qualified, press ENTER to continue
The Service menus main menu will be displayed (menu 3).
MAIN MENU
Image Control
IRIS Control
Sound Control
Function keys
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE
PROJECTOR.
ADJUSTMENT MODE
Select a path from below :
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Source 01
Select with é or ê
then <ENTER>
<EXIT> to return.
The following
SERVICE menus
are reserved to,
and to be performed only
by qualified personnel !
If qualified, press
<ENTER> to continue, or
if not, <EXIT> to return.
menu 3
menu 2
Password Protection
Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password.
(Password protection is only available when the password strap on the contoller module is ON. Contact a BARCO authorized
technician when no password is requested during the adjustment procedure and password protection is desired.)
enter
password
xxxx
Entering the password
Your password contains 4 digits.
Enter the digits with the numeric keys on the RCU.
Example : 2 3 1 9
For each digit entered, a 'X' appears on the screen under the displayed text 'enter password'.
When the password is correct, you gain access to the selected item.
When the entered password is wrong, the error message 'wrong password !!!' will be displayed.
5976194 BARCOCINE 9 31012002
6-1
Entering the Service Menus
When the password is correct, you gain access to the selected item.
When the entered password is wrong, the error message 'wrong password !!!' will be displayed.
Remark :
When the password is correctly entered, all other password protected items are accessible without re-entering the password.
When re-entering the adjustment mode, it will be necessary to enter your password again when selecting a password protected item.
6-2
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
7
RANDOM ACCESS ADJUSTMENT MODE
Random access adjustment mode.
Starting Up
Push the cursor keys up or down to highlight "RANDOM ACCESS" and then press ENTER.
Some items in the Random access mode are password protected (when the password function is enabled). Enter your password
to continue. All other password protected items are now also available if you stay in the adjustment mode.
ADJUSTMENT MODE
Select a path from below :
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Source 01
Select with é or ê
then <ENTER>
<EXIT> to return.
Overview Flowchart
PORT 2
COLOR BALANCE
SYNC
PICTURE TUNING
LINE MULTIPLIER
PEAKING
CLAMP TUNING
H PHASE
RANDOM ACCESS
ADJUSTMENT MODE
SETUP PATTERN SELECTION
V CENTERLINE BOW
V CENTERLINE SKEW
RASTER SHIFT
SIDE BOW
LEFT-RIGHT (E-W)
SIDE KEYSTONE
SEAGULL CORRECTION
GEOMETRY
LEFT KEYSTONE
LEFT SIDE CORRECTIONS
LEFT BOW
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP-BOTTOM (N-S)
TOP BOW
BOTTOM KEYSTONE
SIZE
VER LINEARITY
BOTTOM BOW
SEAGULL CORRECTION
TOP
BOTTOM
BLANKING
LEFT
next page
5976194 BARCOCINE 9 31012002
RIGHT
7-1
Random Access Adjustment Mode
previous page
RED
GREEN
BLUE
COLOR SELECT
RED AND GREEN
BLUE AND GREEN
RED AND BLUE
GREEN ONLY
RANDOM ACCESS
ADJUSTMENT MODE
CONVERGENCE
RED ON GREEN
BLUE ON GREEN
SETUP PATTERN SELECTION
RED
FOCUSING
GREEN
BLUE
ORBITING
CONTRAST MODULATION
SOFT EDGE CORRECTION
Selecting Setup Pattern
Set up of the Selected Setup Pattern ?
If an external source is connected to the projector, menu 1 will be displayed.
To select the desired setup pattern, handle as follow :
1 Push the cursor keys é or ê to highlight the desired setup pattern
2 Press ENTER to select.
Choose a setup pattern
from below :
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Source 01
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Genlocked pattern : internally generated cross hatch pattern, locked on the external source.
Internal # pattern : internally generated cross hatch pattern and locked on internal generated sync signals. (No external source
necessary)
If no external source is connected to the projector, the internal cross hatch pattern menu will be displayed.
Note:
The menus in this manual are created for an external source, connected to one of the inputs, and the 'Genlocked Pattern' is selected.
7-2
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Internal Cross Hatch Pattern
When using the Internal Cross Hatch Pattern ?
The Internal # pattern menu will be displayed if the internal cross hatch pattern has been selected or if no source is connected to
the projector.
Factory Preset Frequencies
The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are custom programmable.
To select a desired cross hatch frequency, handle as follow :
Push the cursor keys é or ê to highlight the desired cross hatch frequency (menu 1).
Push the cursor keys ç or è to scroll to another page.
Press ENTER if the desired block is selected.
1
2
3
kHz/Hz
15.6/50
15.7/60
31.2/50
31.5/60
31.2/50
31.5/60
33.7/60
15.8/60
21.8/60
61.0/76
35.5/87
44.2/70
48.5/60
61.0/76
72.1/67
89.3/67
PAL/SECAM
NTSC
EDTV
IDTV
HDTV EUREKA
HDTV ATV
HDTV HIVISION
EGA 1
EGA 2
VGA 1,2
VGA 4
Super VGA 2
Super VGA 1
Super VGA 3
Super VGA 4
SUN 3/260
INTERNAL # PATTERN
kHz / Hz
15.6/50
15.7/60
31.2/50
31.5/60
31.2/50
31.5/60
PAL/SECAM
NTSC
EDTV
IDTV
HDTV EUREKA
HDTV ATV
Select with é or ê
scroll with ç or è
<ENTER> to accept
<EXIT> to return
menu 1
Random access adjustment mode selection menu.
What is possible ?
This is the main menu for the Random Access adjustment mode.
Through this menu, the following adjustments and features are accessible :
- Picture Tuning
Sync slow/fast(only for RGB inputs)
Color Balance
Peaking
Clamp Tuning
Port 2 : Video/S-Video
Line Doubler / Multiplier
- Geometry
- Convergence
- Focussing
- Color select
And also Orbiting, Contrast modulation, Soft Edge if these options are installed.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
7-3
Random Access Adjustment Mode
Picture Tuning
Start up the Picture Tuning
1
2
Push the cursor keys é or ê to highlight Picture tuning (menu 1).
Press ENTER.
The Picture tuning menu will be displayed.
Depending on the input source, the 'Picture tuning' menu will display different items (menu 2).
- Color Balance
- Sync slow/fast
- Port 2 : Video/S-Video
- Line multiplier
- Peaking
- Clamp Tuning
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING
PORT2 : VIDEO
LINE MULTIPLIER : ON
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
<ENTER> to accept
<EXIT> to return.
menu 1
menu 2
Color Balance
What can be done ?
The Color Balance function is used to select or adjust the color temperature of white used by the projector.
The Color Balance can be adjusted on two different ways :
- fixed color balance. You have the choice between 3200 K (reddish), 4900 K, 6500 K (white) or 9300 K (bluish).
- Custom white and black balance.
How to select the Color Balance ?
Push the cursor keys é or ê to highlight 'Color Balance' (menu 1).
Press ENTER to select.
The color balance menu will be displayed (menu 2).
1
2
COLOR BALANCE
PICTURE TUNING
FIXED COLOR BALANCE
3200 4900 6500 9300
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING
PORT2 : VIDEO
LINE DOUBLER : ON
CUSTOM RED & BLUE GAIN
CUSTOM GREEN GAIN
CUSTOM RED & BLUE CUT OFF
CUSTOM GREEN CUT OFF
Select with arrow keys
then <ENTER>
Red & Blue :
adjust red with é or ê
Blue with ç or è
<EXIT> to return
Select with é or ê
<ENTER> to accept
<EXIT> to return.
menu 1
menu 2
Fixed Color Balance
To select a fixed color balance, handle as follow :
1. Highlight one of the 4 preprogrammed color temperatures with the cursor keys and
2. press ENTER to display the image with the desired color balance.
Custom Color Balance.
The custom color balance adjustment can be divided in two parts, the 'gain' adjustment and the 'cut off' adjustment.
Gain adjustment
1.
2.
3.
4.
7-4
Push the cursor key é or ê to select 'Custom Red & Blue gain' (menu 1).
Press ENTER to activate the adjustment.
Push the cursor key é or ê to adjust the red gain
Push the cursor key è or ç to adjust the blue gain.
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
5.
6.
7.
8.
9.
A bar scale indicates the amount of adjustment.
Press ENTER to return to the Color Balance menu.
Push the cursor key é or ê to select 'Custom Green Gain' (menu 2).
Press ENTER to activate the adjustment.
Push the cursor key é or ê to adjust the green gain.
Press ENTER to return to the Color Balance menu.
Cut Off adjustment
1.
2.
3.
4.
5
6.
7.
8.
9.
Push the cursor key é or ê to select 'Custom Red & Blue Cut off' (menu 3).
Press ENTER to activate the adjustment.
Push the cursor key é or ê to adjust the red cut-off
Push the cursor key è or ç to adjust the blue cut-off.
Press ENTER to return to the Color Balance menu.
Push the cursor key é or ê to select 'Custom Green cut off' (menu 4).
Press ENTER to activate the adjustment.
Push the cursor key é or ê to adjust the green cut-off.
Press ENTER to return to the Color Balance menu.
When the color balance is adjusted, press EXIT to return.
COLOR BALANCE
COLOR BALANCE
COLOR BALANCE
COLOR BALANCE
FIXED COLOR BALANCE
3200 4900 6500 9300
FIXED COLOR BALANCE
3200 4900 6500 9300
FIXED COLOR BALANCE
3200 4900 6500 9300
FIXED COLOR BALANCE
3200 4900 6500 9300
CUSTOM RED & BLUE GAIN
CUSTOM GREEN GAIN
CUSTOM RED & BLUE CUT OFF
CUSTOM GREEN CUT OFF
CUSTOM RED & BLUE GAIN
CUSTOM GREEN GAIN
CUSTOM RED & BLUE CUT OFF
CUSTOM GREEN CUT OFF
CUSTOM RED & BLUE GAIN
CUSTOM GREEN GAIN
CUSTOM RED & BLUE CUT OFF
CUSTOM GREEN CUT OFF
CUSTOM RED & BLUE GAIN
CUSTOM GREEN GAIN
CUSTOM RED & BLUE CUT OFF
CUSTOM GREEN CUT OFF
Select with arrow keys
then <ENTER>
Red & Blue :
adjust red with é or ê
Blue with ç or è
<EXIT> to return
Select with arrow keys
then <ENTER>
Red & Blue :
adjust red with é or ê
Blue with ç or è
<EXIT> to return
Select with arrow keys
then <ENTER>
Red & Blue :
adjust red with é or ê
Blue with ç or è
<EXIT> to return
Select with arrow keys
then <ENTER>
Red & Blue :
adjust red with é or ê
Blue with ç or è
<EXIT> to return
menu 1
menu 2
menu 3
menu 4
Sync Fast/Slow Adjustment
What can be done ?
The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image.
The sync slow/fast function is only available for RGB sources.
How to setup the sync function ?
To change the Sync setting, handle as follow :
1. Push the cursor keys é or ê to select Sync (menu 1)
2. Press ENTER to toggle between FAST and SLOW.
Note
SYNC is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video
playback equipment.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
PORT2 : VIDEO
LINE DOUBLER : ON
Select with é or ê
<ENTER> to accept
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
7-5
Random Access Adjustment Mode
Peaking
What can be done ?
Peaking improves the contours in an projected image.
How to set up ?
To change the peaking setting, handle as follow :
1. Push the cursor key é or ê to select Peaking (menu 1).
2. Press ENTER to display the peaking menu (menu 2).
During the creation of new settings for a RGB source the corresponding peaking is switched on as default.
The following frequency areas are available :
15 kHz - 45 kHz : Low frequency peaking.
45 kHz - 85 kHz : Mid frequency peaking.
85 kHz - 110 kHz : High frequency peaking.
If another peaking is desired or switch off, handle as follow :
1. Push the cursor key é or ê to select to select the desired frequency area or off (menu 2).
2. Press ENTER to activate.
PICTURE TUNING
PEAKING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
PORT2 : VIDEO
LINE DOUBLER : ON
OFF
LOW FREQUENCY
MID FREQUENCY
HIGH FREQUENCY
Select with é or ê
<ENTER> to accept
<EXIT> to return.
Select with é or ê
<ENTER> to accept
<EXIT> to return.
menu 1
menu 2
Clamp Tuning
What can be done ?
The clamp tuning can be switch between 'Normal' and 'Restoration'.
Normal : for all standard sources and all sources with a backporch > 0.8 µs or for sources with noise and spikes in the signal.
Restoration : for standard sources with a backporch between 0.4 µs and 0.8 µs or for sources with sync separate or sync on green.
How to set up ?
1. Push the cursor key é or ê to select Clamp Tuning (menu 1).
2. Press ENTER to toggle between 'Normal' and 'Restoration'.
3. Press EXIT to return to the picture tuning menu.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
PORT2 : VIDEO
LINE DOUBLER : ON
Select with é or ê
<ENTER> to accept
<EXIT> to return.
menu 1
7-6
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Port 2 : Video or S-Video
What can be done ?
Port 2 can be used as a Video or S-Video input.
How to configure port 2 ?
To change the Port 2 setting, handle as follow :
1. Push the cursor key é or ê to select Port 2 (menu 1).
2. Press ENTER to toggle between Video and S-Video.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
PORT2 : VIDEO
LINE DOUBLER : ON
Select with é or ê
<ENTER> to accept
<EXIT> to return.
menu 1
Line Multiplier*
What can be done ?
This menu item is only available when the projector is equipped with a line multiplier.
Line multiplying is only possible for Video, S-Video, Component Video images on standard line frequency and RGB signals on 15
kHz.
The multiplier eliminates the video line patterns and improves the image stability. In addition,
- the time base correction virtually eliminates the timing jitter caused by the common videocassette recorders.
- de-interlacing gets rid of line flicker.
- film mode processing makes sure that material that has been converted from 24 Hz cinema to video (2:2 and 3:2 pull down) is displayed
without artifacts.
- dynamic noise reduction can be used to improve noisy video sources.
- static contrast enhancement allows the user to adjust the image contrast to personal taste.
- several detail-enhancing filters bring out details.
The line multiplier when available is active.
The setting of the line multiplier will be saved together with the source number. Each time this source number is selected, the last
saved version will be loaded.
How to select when a line multiplier is built in ?
1. Push the cursor key é or ê to select Line Multiplier (menu 1).
2. Press ENTER to select.
The line multiplier menu will be displayed (menu 2).
IMAGE PROCESSING
PICTURE TUNING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
COLOR BALANCE
SYNC : FAST
DECODING : EBU
LINE MULTIPLIER
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
Select with é or ê
<ENTER> to accept
<EXIT> to return.
ADVANCED SETTINGS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
* only in R9002401
5976194 BARCOCINE 9 31012002
7-7
Random Access Adjustment Mode
Switching the multiplier ON/OFF
1. Push the cursor key é or ê to select Line Multiplier (menu 1).
2. ENTER to toggle between 'Line Multiplier : ON' and 'Line Multiplier : OFF'.
When the line multiplier is on, all items in the menu are accessible.
IMAGE PROCESSING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
ADVANCED SETTINGS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Motion Processing
Why Motion Processing ?
With this function it is possible to recognize whether the source material was originally film or video. That prevents the creation of
motion artifacts.
How to activate ?
1
2
Push the cursor keys é or ê to select 'Motion Processing' (menu 1).
Press ENTER to toggle between ON and OFF.
IMAGE PROCESSING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
ADVANCED SETTINGS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
7-8
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Output Mode
What can be done ?
Within the output mode menu, it is possible to select a new output mode for a given input signal. The input signal can be line multiplied,
interlaced or non-interlaced.
How to select a new scan rate ?
1
2
Push the cursor keys é or ê to select 'Output Mode' (menu 1).
Press ENTER to display the output mode menu (menu 2a or 2b)
Depending on the frequency of the input source, menu 2a or 2b will be displayed.
If your input signal is PAL or SECAM signal, menu 2a will be displayed. If it is a NTSC signal, menu 2b will be displayed.
IMAGE PROCESSING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
LINEMULTIPLIER
OUTPUT MODE
LINEMULTIPLIER
OUTPUT MODE
50Hz 625 Lines NI
100hz 625 Lines NI
50Hz 1250 Lines NI
100Hz 1250 Lines I
60Hz 525 Lines NI
120hz 525 Lines NI
60Hz 1050 Lines NI
120Hz 1050 Lines I
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
ADVANCED SETTINGS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
3
4
menu 2a
menu 2b
Push the cursor keys é or ê to select a new scan rate (menu 3).
Press ENTER to activate this scan rate.
e.g. 100 Hz 625 lines P ==>
Vertical frequency of the image : 50 Hz
Quantity of horizontal lines : 625 lines
Interlace mode : NI = Non-interlaced image (progressive scan).
LINEMULTIPLIER
OUTPUT MODE
50Hz 625 Lines NI
100hz 625 Lines NI
50Hz 1250 Lines NI
100Hz 1250 Lines I
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 3
Video Equalizing
What can be done ?
The sharpness of the image can be adjusted for 3 frequency bands (low, medium and high) separately.
In addition to the pre-programmed factory presets a customized adjustment of the sharpness for 3 ranges is also possible.
How to select Video Equalizing ?
1
2
Push the cursor keys é or ê to select 'Video Equalizing' (menu 1).
Press ENTER to display the adjustment menu (menu 2).
5976194 BARCOCINE 9 31012002
7-9
Random Access Adjustment Mode
How to adjust the Video Equalizing ?
1
2
Push the cursor keys ç or è to select 'Low' or Mid' or 'HI.' or 'Factory Preset : x'
Push the cursor keys é or ê to adjust the sharpness in the choosen band (low, mid, high) or to scroll through the factory preset
(x = 1 to 7).
Factory preset 8 is equal to the custom adjustment as made with low, mid and high.
IMAGE PROCESSING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
LOW
MID
HI.
FACTORY PRESET : x
ADVANCED SETTINGS
Select with ç or è
Adjust or scroll presets
with é or ê
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
Noise Reduction
What can be done ?
Noisy, lower quality video images can be ameliorated by use of the Noise Reduction feature.
How to select and adjust the Noise Reduction ?
1
2
3
4
Push the cursor keys é or ê to select 'Noise Reduction' (menu 1).
Press ENTER to display the adjustment text box (menu 2).
Push the cursor keys é or ê to adjust the noise.
Press ENTER to return to the 'Image Processing' menu.
IMAGE PROCESSING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
Dynamic
Noise Reduction
ADVANCED SETTINGS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Off
Max
menu 2
Contrast Enhancement
What can be done ?
Enhancing the contrast results in a more dynamic image.
How to select and adjust the contrast enhancement ?
1
2
3
4
Push the cursor keys é or ê to select 'Contrast Enhancement' (menu 1).
Press ENTER to display the adjustment text box (menu 2).
Push the cursor keys é or ê to adjust the contrast.
Press ENTER to return to the 'Image Processing' menu.
IMAGE PROCESSING
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
Contrast
Enhancem.
ADVANCED SETTINGS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
7-10
-3
0
+3
menu 2
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Advanced Settings
How to select the Advanced Settings ?
1. Push the cursor key é or ê to select 'Advanced Settings' (menu 1).
2. Press ENTER to select.
The advanced Settings menu will be displayed (menu 2).
A warning is displayed in the advanced settings menu : "Advanced adjustment should be performed only by qualified personnel".
IMAGE PROCESSING
LINE MULTIPLIER
LINE MULTIPLIER : ON
MOTION PROCESSING : ON
TIME BASE CORRECTION
LUMINANCE DELAY
V SYNC REF : INDIRECT
CLAMP GATING : OFF
FACTORY PRESET
OUTPUT MODE
VIDEO EQUALIZING
NOISE REDUCTION
CONTRAST ENHANCEMENT
ADVANCED SETTINGS
WARNING : ADVANCED
ADJUSTMENT SHOULD BE
PERFORMED ONLY BY QUALIFIED
PERSONNEL
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
Time Base Correction
Why Time Base Correction ?
With the Time Base Correction function it is possible to clean-up low quality videotape noise to obtain a more stable image.
How to activate ?
Push the cursor keys é or ê to select 'Time Base Correction' (menu 1).
Press ENTER to toggle between ON and OFF.
1
2
LINE MULTIPLIER
TIME BASE CORRECTION
LUMINANCE DELAY
V SYNC REF : INDIRECT
CLAMP GATING : OFF
FACTORY PRESET
WARNING : ADVANCED
ADJUSTMENT SHOULD BE
PERFORMED ONLY BY QUALIFIED
PERSONNEL
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Luminace Delay
When is it necessary ?
When a color shift is recognized on the screen. e.g. if color bars are projected and a line between the color is recognized.
How to adjust ?
1.
2.
3.
4.
Push the cursor key é or ê to select 'Luminance delay' (menu 1).
Press ENTER to activate.
Push the cursor key é or ê to adjust the luminance delay until the color shift is eliminated (menu 2).
Press ENTER to return to the 'Advanced Settings' menu.
LINE MULTIPLIER
TIME BASE CORRECTION
LUMINANCE DELAY
V SYNC REF : INDIRECT
CLAMP GATING : OFF
FACTORY PRESET
WARNING : ADVANCED
ADJUSTMENT SHOULD BE
PERFORMED ONLY BY QUALIFIED
PERSONNEL
Luminance
Delay
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
-
0
+
menu 2
7-11
Random Access Adjustment Mode
Vertical Sync Reference
Why necessary ?
DIRECT: This sync processing has the disadvantage that glitches and other disturbances in the video signal sometimes get passed
and hence may cause problems in the image.
INDIRECT: This sync processing throws away any disturbances that are not really sync signals. By source switching a rolling effect
on the image can occur. This sync processing is preferred especially with low quality material.
How to change the vertical sync reference ?
1. Push the cursor key é or ê to select 'V Sync Ref' (menu 1).
2. Press ENTER to toggle between 'direct' and ' indirect'.
Default position : indirect.
LINE MULTIPLIER
TIME BASE CORRECTION
LUMINANCE DELAY
V SYNC REF : INDIRECT
CLAMP GATING : OFF
FACTORY PRESET
WARNING : ADVANCED
ADJUSTMENT SHOULD BE
PERFORMED ONLY BY QUALIFIED
PERSONNEL
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Clamp Gating
Why necessary ?
Clamp Gating is useful when protection signals are present in the vertical interval of the video signal that would otherwise confuse
the LiMoPro
How to change the Clamp Gating ?
1. Push the cursor key é or ê to select 'Clamp Gating' (menu 1).
2. Press ENTER to toggle between ON and OFF.
Default position : OFF.
LINE MULTIPLIER
TIME BASE CORRECTION
LUMINANCE DELAY
V SYNC REF : INDIRECT
CLAMP GATING : OFF
FACTORY PRESET
WARNING : ADVANCED
ADJUSTMENT SHOULD BE
PERFORMED ONLY BY QUALIFIED
PERSONNEL
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Factory Preset
What can be done ?
All settings for the line multiplier can be set to factory preset settings.
What are the factory preset settings ?
The factory preset settings are :
Time base correction : on
Luminace delay : 0
Vertical sync reference : indirect
Clamp gating : off
7-12
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Limo Pro Options
How to select the Limo Plus Options ?
1. Push the cursor key é or ê to select 'Limo Plus Options' (menu 1).
2. Press ENTER to display the limo plus menu (menu 2).
LINE MULTIPLIER
LINE MULTIPLIER
TIME BASE CORRECTION
LUMINANCE DELAY
V SYNC REF : INDIRECT
CLAMP GATING : OFF
CORING
LTI
CTI
Warning : advanced adjustment
should be performed only by
qualified personnel !
LIMO PLUS OPTIONS
FACTORY PRESET
Select with é or ê
then <ENTER>
<EXIT> to return.
WARNING : ADVANCED
ADJUSTMENT SHOULD BE
PERFORMED ONLY BY QUALIFIED
PERSONNEL
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
menu 1
Coring
What can be done ?
With coring, a noise threshold will be set for all filters.
How to set up ?
1. Push the cursor key é or ê to select 'Coring' (menu 1).
2. Press ENTER to select coring.
3. Use the cursor keys to adjust the coring (noise threshold).
LINE MULTIPLIER
CORING
LTI
CTI
Warning : advanced adjustment
should be performed only by
qualified personnel !
Select with é or ê
then <ENTER>
<EXIT> to return.
Coring
0
menu 1
menu 2
LTI
What can be done ?
LTI = Luminance transient improvement.
This function makes the luminance transients sharper (from dark areas to highlight areas) without overshoot, undershoot or ringing.
How to set up ?
1. Push the cursor key é or ê to select 'LTI' (menu 1).
2. Press ENTER to select.
3. Use the cursor keys to change the LTI value. Only 7 steps are possible.
LINE MULTIPLIER
CORING
LTI
CTI
LTI
0
7
menu 2
Warning : advanced adjustment
should be performed only by
qualified personnel !
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Adjust LTI for max black and white transient improvement
5976194 BARCOCINE 9 31012002
7-13
Random Access Adjustment Mode
CTI
What can be done ?
CTI = Chrominance (color) transient improvement.
This function makes the chrominance transients (from one color to another) sharper without overshoot, undershoot or ringing.
How to set up ?
1. Push the cursor key é or ê to select 'CTI' (menu 1).
2. Press ENTER to select.
3. Use the cursor keys to change the CTI value. Only 7
steps are possible.
LINE MULTIPLIER
CORING
LTI
CTI
CTI
0
7
menu 2
Warning : advanced adjustment
should be performed only by
qualified personnel !
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Adjust CTI for max colour transient improvement
Geometry Adjustments
What can be done ?
The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other
color images. The following adjustments can be adjusted Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude,
Vertical Amplitude, Vertical Linearity and Horizontal Phase.
Start Up
To start up the geometry corrections, handle as follow :
1. Push the cursor key é or ê to highlight 'Geometry' (menu 1).
2. Press ENTER to select.
The Geometry menu will be displayed on the screen (menu 2).
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
Important
The convergence corrections are disabled during geometry corrections. The blanking corrections are only enabled during the
blanking adjustments.
Horizontal Phase Adjustment
Start Up
1. Push the cursor key é or ê to highlight 'H Phase' (menu 1).
2. Press ENTER to activate.
The external image with a text box in the middle will be projected.
Note
No horizontal phase adjustment is available on the internal # pattern.
7-14
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
How to adjust ?
If the raster shift is correctly adjusted, the H Phase text box is projected in the middle of the raster. At that moment, the "><" icon
indicates the middle of the raster.
Adjust the H Phase control until the middle of the projected image is equal with the middle of >< icon.
Image 1 : Push the cursor key to the right to correct.
Image 2 : Push the cursor key to the left to correct.
Note : If the genlocked pattern was selected during the start up of the random access mode, the external source will be displayed.
A bar scale and a number indicator (between 0 and 100) on the screen give a visual indication of the horizontal phase adjustment.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
Select with é or ê
then <ENTER>
<EXIT> to return.
><
H PHASE
><
H PHASE
70
menu 1
70
image 1
image 2
Raster Shift Adjustment
What has to be done ?
The green raster must be centered both horizontally and vertically on the center of the CRT surface. To center the green raster,
look into the green lens and use the cursor keys to move the raster.
CAUTION
It is necessary to look into the lenses to perform these adjustments. To avoid eye discomfort while looking into the lenses, reduce
the contrast and gradually increase the brightness level until the raster becomes visible on the face of the CRT.
Start up
To
1.
2.
3.
4.
5.
start the adjustment (image 1) :
push the cursor key é or ê to highlight Raster Shift (menu 1).
press ENTER to display the coarse shift menu (menu 2)
Select first green horizontal and adjust.
Continue with green vertical.
Shift red and blue on green.
Note
Horizontal and Vertical shifts for Red and Blue should end up with a setting close to 50%. If these settings are significantly greater
or lesser than 50%, contact a BARCO authorized service technician.
Warning
In order to ensure maximum CRT longevity and to avoid CRT damage, do not shift the raster outside the phosphor area of the CRT.
GEOMETRY
COARSE SHIFT
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
GREEN HORIZONTAL
GREEN VERTICAL
RED VERTICAL
BLUE VERTICAL
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
forbidden area
projected raster
crt faceplate border
menu 2
phosphor border
image 1
5976194 BARCOCINE 9 31012002
7-15
Random Access Adjustment Mode
Left-Right (east-west) Adjustments
What can be adjusted ?
Left-right and center adjustments affect only the vertical lines of the projected image. The skew, the bow, the keystone and the seagull
distorsion can be adjusted.
Start up
To start up the left-right and center adjustments, follow the next procedure :
1. Push the cursor key é or ê to highlight LEFT-RIGHT (E/W) (image 1).
2. Press ENTER to select.
The 'Left-Right' menu will be displayed (menu 2).
GEOMETRY
LEFT-RIGHT (E-W)
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Warning : Use this correction to
adjust the right side of the image !
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
menu 2
Note
Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be corrected in
the same manner. Convergence corrections are automatically disabled for the duration of these adjustments.
Which adjustment can be executed ?
The following adjustments can be executed
-
vertical centerline bow
vertical centerline skew
side keystone (left - right)
side bow (left - right)
All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines are straight.
How to enter an alignment ?
To
1.
2.
3.
7-16
enter an alignment :
Push the cursor key é or ê to highlight a function
Press ENTER to activate this function.
Press EXIT to return.
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Warning
Use this correction to adjust the right side of the image.
Corrects for curvature of the vertical lines in the middle of the
image.
LEFT-RIGHT
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
Corrects the tilting of the vertical lines in the middle of the
image.
Select with
or
then <ENTER>
<EXIT> to return.
Corrects for curvature of the vertical lines on the right side
Corrects the keystone geometry correction of the vert. lines
on the right side
Correct by pushing
the cursor keys to
the right
Correct by pushing
the cursor keys to
the left
Seagull correction
What can be done ?
Use this correction only if, after adjusting the vertical lines with the side bow or side keystone, still a 'S' deformation is visible on the
left and the right side of the image.
The default value on the bar scale for this correction is 50.
Start up
To correct the Seagull Correction :
1. Push the cursor key é or ê to highlight SEAGULL CORRECTION (menu 1)
2. Press ENTER to activate.
Eliminate the deformation by pushing the cursor key ç or è until a straight line is obtained (image 1).
LEFT-RIGHT (E-W)
V CENTERLINE BOW
V CENTERLINE SKEW
RIGHT BOW
RIGHT KEYSTONE
LEFT BOW
LEFT KEYSTONE
SEAGULL CORRECTION
Select with é or ê
then <ENTER>
<EXIT> to return.
image 1
menu 1
5976194 BARCOCINE 9 31012002
7-17
Random Access Adjustment Mode
Left Side Correction
What can be done ?
Fine tuning on the left side of the image for bow and keystone correction.
Only the green image is displayed while making the left side adjustments. The red and blue images will automatically be corrected
in the same manner.
The convergence corrections are automatically disabled for the duration of these adjustments.
Warning
Before starting the left side correction, insure that the side bow and keystone adjustments are done prior to these fine adjustments!
Start Up
1. Push the cursor key é or ê to highlight 'Left Side Correction' (menu 1).
2. Press ENTER to display the Left Side Correction menu (menu 2).
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
LEFT SIDE CORRECTION
LEFT KEYSTONE
LEFT BOW
Ensure that the side bow and
keystone adjustments are done prior
to these fine adjustments !
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
Left Side Adjustments
1. Push the cursor key é or ê to highlight the desired correction (menu 1).
2. Press ENTER to start the adjustment.
3. Press EXIT to return when the adjustment is finished.
LEFT SIDE CORRECTION
LEFT KEYSTONE
LEFT BOW
Ensure that the side bow and
keystone adjustments are
done prior to these fine
adjustments !
Correct the keystone geometry distortion of the
vertical lines
Select with é or ê
then <ENTER>
<EXIT> to return.
Correct the bow geometry distortion of the
vertical lines
Correct by pushing the
cursor keys to the
right
7-18
Correct by pushing the
cursor keys to the
left
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Top-Bottom (north-south) Adjustments
What can be adjusted ?
Top-Bottom and center adjustments affect only the horizontal lines of the projected image. The skew, the bow, the keystone and
the seagull deviation can be adjusted.
Start Up
To start up the Top-Bottom and center corrections, follow the next procedure :
1. Push the cursor key é or ê to highlight TOP-BOTTOM (N/S) (menu 1).
2. Press ENTER to select.
The Top-Bottom menu will be selected (menu 2).
GEOMETRY
TOP-BOTTOM (N-S)
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTIONS
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
Note
Only the green image is displayed while making top-botton adjustments. The red and blue images will automatically be corrected
in the same manner. Convergence corrections are automatically disabled for the duration of these adjustments.
Which adjustment can be executed ?
The following adjustments can be executed
-
horizontal centerline bow
horizontal centerline skew
Top bow
Top keystone
Bottom bow
Bottom keystone
All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100.
Adjust the next alignments until the horizontal lines are straight.
How to enter an alignment ?
To
1.
2.
3.
enter an alignment :
Push the cursor key é or ê to highlight a function
Press ENTER to activate this function.
Press EXIT to return.
5976194 BARCOCINE 9 31012002
7-19
Random Access Adjustment Mode
Corrects for curvature of the horizontal lines in the middle
of the image.
Corrects the tilting of the horizontal lines in the middle of
the image.
TOP-BOTTOM
H CENTERLINE BOW
H CENTERLINE SKEW
TOP BOW
TOP KEYSTONE
BOTTOM BOW
BOTTOM KEYSTONE
Corrects for curvature of the horizontal lines on the upper side
Select with
or
then <ENTER>
<EXIT> to return.
Corrects the keystone geometry correction of the hor. lines on
the upper side
Corrects for curvature of the horizontal lines on the lower side
Corrects the keystone geometry correction of the hor. lines on
the lower side
Correct by pushing
the cursor key down
Correct by pushing
the cursor key up
Seagull correction
What can be done ?
Use this correction after the image has been adjusted with top and bottom bow and keystone. If still a deformation (like a seagull)
on top and bottom of the image is visible, proceed to the seagull correction. Due to interaction, it is possible that the top and bottom
bow have to be readjusted after adjusting the seagull correction to obtain an improved image. The default value on the bar scale
of this correction is 50.
7-20
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Start up
To correct the Seagull Correction :
1. Push the cursor key é or ê to highlight SEAGULL CORRECTION (menu 1)
2. Press ENTER to activate.
Eliminate the deformation by pushing the cursor key é or ê until a straight line is obtained (image 1).
TOP-BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
image 1
Horizontal Size Adjustment
What can be done ?
To adjust (correct) a little bit the horizontal picture size (when the projector is on its correct position) in regard with the installed screen
Start up
1. Push the cursor key é or ê to highlight 'H Size' (menu 1).
2. Press ENTER to activate (menu 2).
3. Push the cursor key ç or è until the exact image width is obtained (horizontal size) (image 1).
Note :
- If the internal # pattern was selected, this pattern remains on the screen.
- If the genlocked pattern was selected, the external source will be displayed.
A bar scale and a numeric indicator help to gauge the size adjustment.
Hint
In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity, do not use an excessively small
horizontal size setting.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTIONS
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with é or ê
then <ENTER>
<EXIT> to return.
H SIZE
menu 1
70
menu 2
H size too
large
Ideal image width
H size too
small
image 1
5976194 BARCOCINE 9 31012002
7-21
Random Access Adjustment Mode
Vertical Linearity Adjustment
What can be done ?
The vertical linearity adjustment function corrects for vertical non-linearities which extend from the center of the image to the top and
bottom of the image.
Start Up
To start up the vertical linearity adjustment :
1. push the cursor key é or ê to highlight V Linearity (menu 1).
2. press ENTER to activate (menu 2).
Adjust the vertical linearity with the cursor keys until the distances between the horizontal lines of the set up pattern are equal
from top to bottom (image 1).
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with é or ê
then <ENTER>
<EXIT> to return.
V LINEARITY
menu 1
image 1
70
menu 2
Vertical Size Adjustment
What can be done ?
To adjust (correct) a little bit the horizontal picture size (when the projector is on its correct position) in regard with the installed screen
Start up
1. Push the cursor key é or ê to highlight 'V Size' (menu 1).
2. Press ENTER to activate (menu 2).
3. Push the cursor key é or ê until the exact image height is obtained (vertical size) (image 1).
Note :
- If the internal # pattern was selected, this pattern remains on the screen.
- If the genlocked pattern was selected, the external source will be displayed.
A bar scale and a numeric indicator help to gauge the size adjustment.
Hint
In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity, do not use an excessively small
horizontal size setting.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Ideal
Image
Hight
Image too
Tall
Ideal
Image
Hight
Image too
Short
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
image 1
7-22
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Blanking Adjustments
What can be done ?
Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and
to hide or black out unwanted information (or noise). A 0% on the bar scale indicates no blanking. The following blanking adjustment
are available : Top, Bottom, left and right blanking.
Start Up
To start up the Blanking adjustments, follow the next procedure :
1. Push the cursor key é or ê to highlight Blanking (menu 1).
2. Press ENTER to display the blanking menu (menu 2).
Therefore :
- If the internal # pattern was selected, this pattern remains on the screen.
- If the genlocked pattern was selected, the external source will be displayed.
GEOMETRY
BLANKING
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
How to adjust the Blanking ?
Adjust the next blanking alignments until the image is correctly framed or the unwanted information is blanked out (image 1).
To enter a blanking alignment :
1. Push the cursor key é or ê to highlight the desired blanking position.
2. Press ENTER to select.
3. Press the cursor key é or ê to adjust the blanking.
4. Press ENTER to continue.
Top blanking
Right blanking
Left blanking
Bottom blanking
image 1
5976194 BARCOCINE 9 31012002
7-23
Random Access Adjustment Mode
Adjustment of the blanking on the of the image
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
Adjustment of the blanking on the bottom of the image
Correct by pushing the cursor keys up or
down
Adjustment of the blanking on the left side
Adjustment of the blanking on the right side
Correct by pushing the cursor keys to the
right or to the left
Convergence Adjustment
What has to be done ?
Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on
the red image while superimposed on the green image and then on the blue image while superimposed on the green image. The
screen is devided into 25 areas (image 1)
Note
The green convergence adjustments can be added as an option. When these are available, start always with 'green only'. This option
will also be indicated on the convergence menu.
Adjustment order
Adjust first the 'green only' when available and continue with red on green and blue on green.
Start up
1. Push the cursor key é or ê to select desired adjustment.
2. Press ENTER to activate.
7-24
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
How to adjust ?
1. Use the cursor keys to move the box to the desired zone.
2. Press ENTER to begin the convergence adjustment.
Start the convergence adjustment with zone one and continue as mentioned in the image 1.
3. Use the cursor keys to make horizontal or vertical convergence adjustments in the selected zone (image 2).
4. Press ENTER to move to another zone.
5. Press EXIT to return to the convergence menu.
RANDOM ACCESS
ADJUSTMENT MODE
CONVERGENCE
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
Select with
or
then <ENTER>
<EXIT> to return.
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
25
23
9
15
17
24
22
8
14
16
5
4
1
2
3
20
18
6
10
12
21
19
7
11
13
menu 2
image 1
green image
CONVERGENCE
SEL : select area
using
arrow keys
ADJ : adjust area
using
arrow keys
red image
Toggle between
SEL and ADJ
with <ENTER>
<ENTER> continue
<EXIT> to return
CONVERGE
ADJUSTMENT
70
menu 3
image 2
image 3
Focusing
What can be done ?
After the lenses are mechanically correct focused, the CRT's can be electromagnetic focused until the image is on each point.
Start Up
1. Push the cursor key é or ê to highlight 'Focusing' (menu 1).
2. Press ENTER to display the focusing menu (menu 2).
The focusing has to be done for the three colors separately.
Start with Green and continue with Red and Blue.
The following items can be adjusted per color (menu 3) :
- Midpoint focusing
- Top image focusing
- Bottom image focusing
- Left image focusing
- Right image focusing
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
menu 2
FOCUSING
FOCUSING
RED
GREEN
BLUE
BLUE ON SOURCE
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
Select with
or
then <ENTER>
<EXIT> to return.
menu 3
7-25
Random Access Adjustment Mode
Midpoint Focusing
1.
2.
3.
4.
Push the cursor key é or ê to highlight 'Midpoint' (menu 1).
Press ENTER to start up the midpoint focusing.
Push the cursor key ç or è until the center of the image is sharp.
Press ENTER to return to the focusing menu.
FOCUSING
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
Top Image Focusing
1.
2.
3.
4.
Push the cursor key é or ê to highlight 'Top' (menu 1).
Press ENTER to start up the top image focusing.
Push the cursor key ç or è until the upper part of the image is sharp.
Press ENTER to return to the focusing menu.
FOCUSING
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
Bottom Image Focusing
1.
2.
3.
4.
Push the cursor key é or ê to highlight 'Bottom' (menu 1).
Press ENTER to start up the bottom image focusing.
Push the cursor key ç or è until the lower part of the image is sharp.
Press ENTER to return to the focusing menu.
FOCUSING
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
Left Image Focusing
1.
2.
3.
4.
Push the cursor key é or ê to highlight 'Left' (menu 1).
Press ENTER to start up the top image focusing.
Push the cursor key ç or è until the left part of the image is sharp.
Press ENTER to return to the focusing menu.
FOCUSING
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
7-26
5976194 BARCOCINE 9 31012002
Random Access Adjustment Mode
Right Image Focusing
1.
2.
3.
4.
Push the cursor key é or ê to highlight 'Right' (menu 1).
Press ENTER to start up the right image focusing.
Push the cursor key ç or è until the right part of the image is sharp.
Press ENTER to return to the focusing menu.
FOCUSING
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
Blue on Source
What can be done ?
After focusing the three colors, and a discoloring on a normal image is still visible, select blue on source and repeat the steps Midpoint,
Top, Bottom, Left and Right.
Start Up
1. Push the cursor key é or ê to highlight 'Blue on Source' (menu 1).
2. Press ENTER to start up.
Repeat the midpoint, top, bottom, left and right focusing.
FOCUSING
RED
GREEN
BLUE
BLUE ON SOURCE
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
Color Select
What can be done ?
Only one color (CRT) or a combination of colors can be switched on display the image.
Start Up
1.
2.
3.
4.
5.
Push the cursor key é or ê to highlight 'Color Select' (menu 1).
Press ENTER to display the color select menu (menu 2).
Select the desired color or color combination by pushing the cursor key é or ê .
Press ENTER to select.
Exit returns to the color select menu.
RANDOM ACCESS
ADJUSTMENT MODE
COLOR SELECT
RED
GREEN
BLUE
RED AND GREEN
BLUE AND GREEN
RED AND BLUE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
Select with
or
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
Select with
or
then <ENTER>
<EXIT> to return.
menu 2
7-27
Random Access Adjustment Mode
7-28
5976194 BARCOCINE 9 31012002
Service Mode
8
SERVICE MODE
Service mode.
Start Up
1. Push the cursor key é or ê to select to SERVICE (menu 1).
2. Press ENTER to select.
The service menu will be displayed (menu 2).
Some items in the Service mode are password protected (when the password function is active). Enter your password to continue.
All other password protected items are now also available if you stay in the adjustment mode.
ADJUSTMENT MODE
SERVICE MODE
Select a path from
below :
RANDOM ACCESS
INSTALLATION
SERVICE
source 1
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
Overview flowchart
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
PROJECTOR SET UP
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE
COMMON ADDRESS
COPY A BLOCK
COPY SOFT EDGE BLOCK
SERVICE MODE
MEMORY MANAGEMENT
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
DYNAMIC ASTIGMATISM
GAMMA CORRECTION
CRT RUN IN CYCLE
COMMON SETTINGS
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDAARD
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
5976194 BARCOCINE 9 31012002
8-1
Service Mode
Projector Set-up
What can be done ?
Within the projector set-up menu, the following items can be consultated or set to the
desired setting :
- Identification
- Total run time
- Change password
- Change projector address
- Change baudrate
- Projector warm up
- Power up mode
- Common address
Start up the Projector Set-Up
To select Projector Set-Up :
1. Push the cursor key é or ê to highlight Projector Set Up (menu 1).
2. Press ENTER to display the Projector set up menu (menu 2).
SERVICE MODE
PROJECTOR SET-UP
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
IDENTIFICATION
RUN TIME
CHANGE PASSWORD
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
menu 1
menu 2
Identification
What can be seen ?
The 'Identification' screen gives information concerning :
- Projector address. To change the address of your projector, contact a qualified service technician.
- Software version.
- Configuration.
Possible installations :
* Front-ceiling
* Front-table
* Rear-ceiling
* Rear-table
- Baud rate PC : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be
the same as the baud rate of the connected computer. When there is a difference, contact a qualified service technician to make
the appropriate changes.
- Text ON/OFF
Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed
The status can be changed by pressing the 'TEXT' key once on the RCU.
- Serial no. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.
- Projector Level : from 0 to 6. The higher the level the more software options installed. Contact your vendor for more information.
8-2
5976194 BARCOCINE 9 31012002
Service Mode
How to start up ?
To select Identification :
1. Push the cursor key é or ê to highlight Identification (menu 1).
2. Press ENTER to select.
The identification screen will be displayed (menu 2).
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
CINE 9
Proj. address : 001
Soft. Version : 6.00
Config. : Ceiling
Front
Baudrate PC : 9600
Text : ON
Serial No. : 103589552
Projector level : 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
menu 1
Run Time
What can be displayed ?
The total sytem run time since the first start up can be displayed plus the run time of the separate CRT's since the last reset.
Run Time Note
All projectors leave the factory after a burn-in period of approximately 100 hours.
How to start up ?
To select the different Run Times :
1. Push the cursor key é or ê to highlight 'Run Time (menu 1).
2. Press ENTER to display the run time menu (menu 2)
The amount of time the projector has played since its first start up at the factory will be displayed as the system run time.
The CRT run times will be displayed next to the respective colors.
PROJECTOR SET-UP
RUN TIME
IDENTIFICATION
RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
SYSTEM RUNTIME : 120 h
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
<ENTER> to reset
<EXIT> to return.
menu 1
CRT RUNTIME :
RED : 20 h
GREEN : 20 h
BLUE : 50 h
menu 2
How to Reset the CRT run times ?
1. Push the cursor key é or ê to highlight the color of the CRT for which the Run Time has to be reseted (menu 1).
2. Press ENTER to reset the run time.
3. Press EXIT to return to the Projector Set up menu.
RUN TIME
SYSTEM RUNTIME : 120 h
CRT RUNTIME :
RED : 20 h
GREEN : 20 h
BLUE : 50 h
Select with é or ê
<ENTER> to reset
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
8-3
Service Mode
Change password
What can be done ?
The password code (4 digits) can be changed to a new one.
This item is password protected. First the actual password should be entered before continuing.
Note
Password function is only active if the jumper on the controller is in the 'ON' position.
How to select ?
To select Change Password :
1. Push the cursor key é or ê to highlight 'Change Password' (menu 1).
2. Press ENTER to display the password menu (menu 2).
If it is the first time you enter a password protected item, enter your password and press ENTER.
The current password is displayed. The new password must consist of 4 digits between 0 and 9.
How to enter a new password ?
Handle as follow :
1. Push the cursor key ç or è to select the digits to be changed (menu 2).
2. Press a numeric keys to enter the new digit.
3. Repeat for the other digits.
4. Press ENTER to save the new password.
Before saving the new password, a confirmation screen will be displayed (menu 3).
5. When the displayed password is correct, press ENTER to save.
6. If not correct, press EXIT to cancel the saving.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
Select with é or ê
then <ENTER>
<EXIT> to return.
PASSWORD
CHANGE PASSWORD
Enter new password :
0000
Use ç and è to select,
and reprogram
with numeric keys.
<ENTER> to confirm
<EXIT> to return
Password will be
reprogrammed as xxxx
<ENTER> to confirm
<EXIT> to cancel
menu 3
menu 2
menu 1
Change Projector Address
What can be done ?
Every projector requires an individual address between O and 255. This address can be software installed.
How to change that address ?
To change that address, handle as follow :
PROJECTOR SET-UP
PROJECTOR ADDRESS
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
Enter new projector
address :
000
Use ç and è to select,
and reprogram
with numeric keys.
Highest address is 255
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
<ENTER> to confirm
<EXIT> to return.
menu 2
1. Push the cursor key é or ê to highlight 'Change Projector Address' (menu 1).
2. Press ENTER to select.
The Change Projector Address menu (menu 2) will be displayed and the actual address will be filled in. The first digit is highlighted.
3. Push the cursor key ç or è to select the digit to be changed.
4. Reprogram with the digit keys on the RCU.
5. Press ENTER to confirm.
8-4
5976194 BARCOCINE 9 31012002
Service Mode
Change Baudrate
What can be set up ?
The communication speed between projector and computer has 8 possible speeds. The baud rate speed can be software set up.
The following baud rates are available :
- 38400, 19200, 9600, 4800, 2400, 1200.
How to set up ?
To set up the baudrate :
1. Push the cursor key é or ê to highlight 'Change Baudrate' (menu 1).
2. Press ENTER to select.
The actual baud rate will be highlighted (menu 2)
3. Push the cursor key é or ê to select the desired baudrate.
4. Press ENTER to accept.
BAUDRATE
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
Select new
baudrate :
38400
9600
2400
Select with arrow
keys ;
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
19200
4800
1200
<ENTER> to accept
<EXIT> to return.
menu 2
Projector warm up
What can be done ?
When in the ON position (and the CRT run in cycle is OFF), the projector can start up with a warm up periode. The warm up time
can be set up by the customer as well as the frequency of the warm up source.
During the start up a warm up menu will be displayed. This menu offers the possibility to skip the warm up periode anyway by pressing
the EXIT key and offers the possibility to adjust the horizontal and vertical amplitude of this white image with the cursor keys. During
this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in.
Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go.
When EXIT is pressed during this warm up periode, the warm up menu will be redisplayed with the remaining time indication. Press
another time EXIT to interrupt the warm up cycle.
When the warm up option is OFF, when switching on the projector, it starts immediately with the projection of the selected source.
How to select ?
1. Push the cursor key é or ê to highlight 'Projector Warm up' (menu 1).
2. Press ENTER to select.
The projector warm up menu will be displayed (menu 2).
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
PROJECTOR WARM UP
WARM UP : ON
FREQUENCY : 64 kHz
TIME : 15 min
A FULL WHITE PATTERN
WILL BE GENERATED AT
POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
with <ENTER>
<EXIT> to return
menu 2
8-5
Service Mode
Warm up ON/OFF
What can be done ?
The warm up option can be toggle between on and off.
When in the on position, while starting up the projector, the warm up cycle will be executed.
When in the off position, the projector starts up with inmediate image projection.
How to install ?
1. Push the cursor key é or ê to highlight 'Warm up' (menu 1).
2. Press ENTER to toggle between ON and OFF.
PROJECTOR WARM UP
WARM UP : ON
FREQUENCY : 64 kHz
TIME : 15 min
A FULL WHITE PATTERN
WILL BE GENERATED AT
POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
with <ENTER>
<EXIT> to return
menu 1
Warm Up Frequency
What can be done ?
The line frequency of the white pattern on which the warm up will be executed, can be entered by selecting out of the displayed
list an available block.
How to install a warm up frequency ?
1.
2.
3.
4.
5.
Push the cursor key é or ê to highlight 'Frequency' (menu 1).
Press ENTER to display the projector warm up frequency selection menu (menu 2).
Select a block with the cursor keys.
Press ENTER to copy the settings of the selected block to the warm up block.
Press EXIT to return.
PROJECTOR WARM UP
WARM UP : ON
FREQUENCY : 64 kHz
TIME : 15 min
A FULL WHITE PATTERN
WILL BE GENERATED AT
POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
with <ENTER>
<EXIT> to return
Nr.
1
2
3
4
5
6
PROJECTOR
Src Fh Fv
1
15.6 50
3
31.2 60
15.6 50
2
31.5 50
33.7 60
WARM UP
inp
conf
video FC
RGB3S R T
intern FC
RGB3S FC
intern FC
Active block nr. 1
Select block to copy data from with é
or ê
<ENTER> to copy settings to warm up
block.
<EXIT> to return.
menu 2
menu 1
Projector Warm Up Time
What can be done ?
The warm up time can be programmed with the cursor keys.
How to program the warm up time ?
1. Push the cursor key é or ê to highlight 'Time' (menu 1).
2. Press ENTER to display the projector warm up time menu (menu 2).
3. Use the cursor keys to select the first digit and reprogram with the numeric keys. Repeat for the other digits.
The projector warm up time is given in minutes.
PROJECTOR WARM UP
WARM UP : ON
FREQUENCY : 64 kHz
TIME : 15 min
A FULL WHITE PATTERN
WILL BE GENERATED AT
POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
PROJECTOR WARM UP
Enter new time :
15 min
Use and to select
and reprogram
with numeric keys
<ENTER> to confirm
<EXIT> to return
with <ENTER>
<EXIT> to return
menu 1
8-6
menu 2
5976194 BARCOCINE 9 31012002
Service Mode
Power up mode
What can be done ?
When pressing the power switch, the projector can start up in 'operating mode' or in 'stand-by mode'.
Operating mode : the projector start up and displays image .
Stand-by mode : the projector start up in stand-by and waits until the stand-by button or a digit key is pressed.
How to change the mode ?
To change the Power up mode:
1. Push the cursor key é or ê to highlight Power Up (menu 1).
2. Press ENTER to toggle between 'Operating' and 'Standby'.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Common Address
What can be done ?
Every projector listens to a common address. This common address can be set to '0' or '1'. When a RCU is programmed with that
common address, every projector with that same common address will follow up the commands given by that RCU.
Why 2 different common address ?
The reason to have the choice to select between common addresses is, to avoid controlling of other IR controlled units, e.g. a TV
set with standard common address 0.
How to change the common address ?
1. Push the cursor key é or ê to highlight Common Address (menu 1).
2. Press ENTER to toggle between '0' and '1'.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
PROJECTOR WARM UP
POWER UP MODE : operating
COMMON ADDRESS : 0
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
8-7
Service Mode
Memory management
What can be done ?
Within the memory management menu, the following items can be consultated or executed :
- copy a block
- copy soft edge block
- delete a block
- delete all blocks
- set to midposition
How to select ?
To select Memory Management :
1. Push the cursor key é or ê to highlight Memory Management (menu 1).
2. Press ENTER to select.
The memory management menu will be displayed (menu 2).
SERVICE MODE
MEMORY MANAGEMENT
COPY A BLOCK
COPY SOFT EDGE BLOCK
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
menu 1
Copy a block
What can be done ?
The copy a block function copies the settings of a selected block into the active block.
How to copy ?
To copy a block :
1. Push the cursor key é or ê to highlight 'Copy a Block' (menu 1).
2. Press ENTER to select.
The copy menu will be displayed (menu 2).
To copy the settings of a closed block to the block you are working on (active block),
3. Push the cursor key é or ê to select a block.
4. Press ENTER to copy the selected block.
All current settings will be overwritten with the settings of the block which is copied.
A confirmation screen will be displayed (menu 3).
5. ENTER to confirm.
EXIT cancels the copy procedure and returns without copying the block.
MEMORY MANAGEMENT
COPY A BLOCK
COPY SOFT EDGE BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
Nr.
1
2
3
4
5
6
7
8
Src
1
3
2
-
COPY MODE
Fh Fv
inp
15.6 50
video
31.2 60
RGB3S
15.6 50
intern
31.5 50
RGB3S
33.7 60
intern
COPY BLOCK
conf
FC
RT
FC
FC
FC
Active block nr. 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
8-8
Select with é or ê
<ENTER> to copy
<EXIT> to return.
menu 2
All settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 3
5976194 BARCOCINE 9 31012002
Service Mode
Copy softedge settings
What can be done ?
The copy softedge settings copies the settings of the softedge of a selected block into the softedge settings of the active block.
How to copy the softedge settings ?
To copy the softedge settings :
1. Push the cursor key é or ê to highlight 'Copy Softedge settings' (menu 1).
2. Press ENTER to select.
The copy softedge settings menu will be displayed (menu 2).
To copy the softedge settings of a closed block to the block you are working on (active block) :
3. Push the cursor key é or ê to select a block.
4. Press ENTER to copy the softedge settings of the selected block.
All current soft edge settings will be overwritten with the soft edge settings of the block which is copied.
A confirmation screen will be displayed (menu 3).
5. ENTER to confirm.
EXIT cancels the copy procedure and returns without copying the softedge settings.
MEMORY MANAGEMENT
COPY A BLOCK
COPY SOFT EDGE BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
Nr.
1
2
3
4
5
6
7
8
COPY SOFTEDGE MODE
Src Fh Fv
inp
conf
1
15.6 50
video FC
3
31.2 60
RGB3S R T
15.6 50
intern FC
2
31.5 50
RGB3S FC
33.7 60
intern FC
Active block nr. 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
COPY SOFTEDGE SETTING
All softedge settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
Select with é or ê
<ENTER> to copy
<EXIT> to return.
menu 3
menu 2
Deletion of blocks
What can be done ?
The delete function is used to clear all data (settings) from an adjustment block.
A delete can be given :
- block by block
or
- for all blocks.
This item is password protected.
Deleting block by block
What can be done ?
The 'delete a block' function deletes the settings of a selected block.
How to delete a Block ?
Push the cursor key é or ê to highlight Delete a Block (menu 1).
Press ENTER to display the delete mode (menu 2).
Push the cursor key é or ê to select the desired adjustment block.
Press ENTER to delete the selected adjustment block.
A confirmation menu will be displayed (menu 3).
5. Press ENTER to confirm.
Press EXIT to cancel the deletion procedure
1.
2.
3.
4.
MEMORY MANAGEMENT
COPY A BLOCK
COPY SOFT EDGE BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
Nr.
1
2
3
4
5
6
7
8
Src
1
3
2
-
DELETE
Fh Fv
15.6 50
31.2 60
15.6 50
31.5 50
33.7 60
MODE
inp
video
RGB3S
intern
RGB3S
intern
DELETE BLOCK
conf
FC
RT
FC
FC
FC
The selected block
will be deleted !
Active block nr.
Select with é or ê
then <ENTER>
<EXIT> to return.
1
Select with é or ê
<ENTER> to copy
<EXIT> to return.
<ENTER> to confirm
<EXIT> to cancel
menu 3
menu 1
5976194 BARCOCINE 9 31012002
menu 2
8-9
Service Mode
Deletion of all blocks
What can be done ?
All blocks (all settings) can be deleted at the same time.
How to delete all blocks ?
1. Push the cursor key é or ê to highlight Delete all Blocks (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed (menu 2).
3. Press ENTER to confirm
Press EXIT to return without deleting any block.
Once ENTER is pressed, all block headers and adjustment settings are permanently removed and cannot be restored.
MEMORY MANAGEMENT
DELETE ALL BLOCKS
COPY A BLOCK
COPY SOFT EDGE BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
All blocks
will be deleted !
Select with é or ê
then <ENTER>
<EXIT> to return.
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Set to midposition
What can be done ?
All adjustment settings (geometry and convergence) can be set to mid position.
Item is password protected.
How to Start Up ?
1. Push the cursor key é or ê to highlight 'Set to Midposition' (menu 1).
2. Press ENTER to display the set to midposition menu (menu 2).
MEMORY MANAGEMENT
SET TO MIDPOSITION
COPY A BLOCK
COPY SOFT EDGE BLOCK
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
R & B convergence mid
What can be done ?
All convergence settings for red and blue are set to midposition.
Item is password protected.
8-10
5976194 BARCOCINE 9 31012002
Service Mode
How to set convergence to midposition :
1. Push the cursor key é or ê to highlight 'R & B Convergence Mid' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
R & B CONVERGENCE MID
Convergence settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 2
Undo R & B convergence mid
What can be done ?
When "R & B convergence mid" is selected, all convergence settings are set to their midposition. With the undo, it is possible to return
to the previous settings as long as the projector is playing on the same source (= same adjustment block).
'Undo R & B convergence mid' is displayed in the Set Midposition menu in stead off 'R & B convergence mid' when this latter is pressed.
How to Undo ?
1. Push the cursor key é or ê to highlight 'Undo R & B convergence mid' (menu 1).
2. Press ENTER execute the undo function.
SET TO MIDPOSITION
UNDO R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Green convergence mid
What can be done ?
The green convergence settings can be set to midposition.
Only available when the projector is equipped with green convergence adjustments.
How to set Green settings to midposition ?
1. Push the cursor key é or ê to highlight 'GR Convergence Mid' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the green convergence settings to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
GR CONVERGENCE MID
Convergence settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
5976194 BARCOCINE 9 31012002
8-11
Service Mode
Undo green convergence mid
What can be done ?
'Undo Gr convergence mid' is displayed in the Set Midposition menu in stead off 'Gr convergence mid' when this latter is pressed.
Only available when the projector is equipped with green convergence adjustmentes.
How to undo ?
1. Push the cursor key é or ê to highlight 'Undo Gr convergence mid' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
UNDO GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Focus to Midposition
What can be done ?
The focus settings can be set to midposition.
How to set the Focus settings to midposition ?
1. Push the cursor key é or ê to highlight 'Focus to midposition' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the focus settings to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
FOCUS TO MIDPOSITION
Focus settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Undo Focus to Midposition
What can be done ?
'Undo Focus to Midposition' is displayed in the Set Midposition menu in stead off 'Focus to midposition' when this latter is pressed.
As long the projector is running on the same source (= same adjustment block), undo the focus to midposition is possible.
How to undo the Focus to midposition ?
1. Push the cursor key é or ê to highlight 'Undo Focus to midposition' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
UNDO FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
8-12
5976194 BARCOCINE 9 31012002
Service Mode
East-West to Midposition
What can be done ?
The east-west settings can be set to midposition.
How to set the E-W settings to midposition ?
1. Push the cursor key é or ê to highlight 'E-W to midposition' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the E-W settings to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
E-W TO MIDPOSITION
E-W settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Undo East-West to midposition
What can be done ?
'Undo East-West to midposition' is displayed in the Set Midposition menu in stead off 'E-W to midposition' when this latter is pressed.
The settings for the E-W can be returned to previous installed settings as long the projector is playing on the same source ( = same
adjustment block).
How to Undo the E-W to midposition ?
1. Push the cursor key é or ê to highlight 'Undo E-W to midposition' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
UNDO E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
North-South settings to Midposition
What can be done ?
The north-south settings can be set to midposition.
5976194 BARCOCINE 9 31012002
8-13
Service Mode
How to set the N-S settings to midposition ?
1. Push the cursor key é or ê to highlight 'N-S to midposition' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the N-S settings to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
N-S TO MIDPOSITION
North-South settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Undo North-South setting to midposition
What can be done ?
'Undo N-S to midposition' is displayed in the Set Midposition menu in stead off 'N-S to midposition' when this latter is pressed.
The settings for the N-S can be returned to previous installed settings as long the projector is playing on the same source ( = same
adjustment block).
How to Undo the N-S to midposition ?
1. Push the cursor key é or ê to highlight 'Undo N-S to midposition' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
UNDO N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Digital Vertical Linearity to Midposition
What can be done ?
The digital vertical linearity settings for the different areas can be set to their midposition.
How to set the Digital Vertical Linearity to Midposition ?
1. Push the cursor key é or ê to highlight 'Dig Vert Linearity mid' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the Digital vertical linearity to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
DIG VERT LINIARITY TO
MIDPOSITION
Dig vert Linearity settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
8-14
5976194 BARCOCINE 9 31012002
Service Mode
Undo Digital Vertical Linearity to Midposition
What can be done ?
'Undo digital vertical linearity to midposition' is displayed in the Set Midposition menu in stead off 'Dig Vert Linearity to midposition' when
this latter is pressed.
The settings for the dig vert linearity can be returned to previous installed settings as long the projector is playing on the same source
( = same adjustment block).
How to undo the digital vertical linearity to midposition ?
1. Push the cursor key é or ê to highlight 'Undo dig vert linearity to midposition' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
UNDO DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Digital Horizontal Linearity to midposition
What can be done ?
The digital horizontal linearity settings for the different areas can be set to their midposition.
How to set the Digital Horizontal Linearity to Midposition ?
1. Push the cursor key é or ê to highlight 'Dig Hor Linearity mid' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the Digital horizontal linearity to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
DIG HOR LINIARITY TO
MIDPOSITION
Dig hor Linearity settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Undo Digital Horizontal Linearity to Midposition
What can be done ?
'Undo digital horizontal linearity to midposition' is displayed in the Set Midposition menu in stead off 'Dig Hor Linearity to midposition'
when this latter is pressed.
The settings for the dig hor linearity can be returned to previous installed settings as long the projector is playing on the same source
( = same adjustment block).
5976194 BARCOCINE 9 31012002
8-15
Service Mode
How to undo the digital vertical linearity to midposition ?
1. Push the cursor key é or ê to highlight 'Undo dig vert linearity to midposition' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
UNDO DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Astigmatism midposition
What can be done ?
The astigmatism settings for the different areas can be set to their midposition.
How to set the Astigmatism to Midposition ?
1. Push the cursor key é or ê to highlight 'Astigmatism' (menu 1).
2. Press ENTER to select.
A confirmation screen will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the Astigmatism to their midposition.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
ASTIGMATISM TO MIDPOSITION
Astigmatism settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Undo Astigmatism setting to midposition
What can be done ?
'Undo Astigmatism midposition' is displayed in the Set Midposition menu in stead off 'Astigmatism midposition' when this latter is pressed.
The settings for the astigmatism can be returned to previous installed settings as long the projector is playing on the same source
( = same adjustment block).
How to undo the Astigmatism settings to midposition ?
1. Push the cursor key é or ê to highlight 'Undo astigmatism midposition' (menu 1).
2. Press ENTER undo.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
UNDO ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
8-16
5976194 BARCOCINE 9 31012002
Service Mode
All settings to Midposition
What can be done ?
All adjustment settings can be set to midposition.
How to set to midposition ?
1. Push the cursor key é or ê to highlight 'All Settings to Midposition' (menu 1).
2. Press ENTER to select.
A confirmation menu will be displayed first (menu 2).
3. Press ENTER to confirm.
Press EXIT to cancel the operation 'set all settings to their midposition'.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
ALL SETTINGS TO MIDPOSITION
All settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
menu 2
menu 1
Undo all settings to midpos
What can be done ?
'Undo all settings to Midposition' is displayed in the Memory management menu in stead off 'All settings to midposition' when this latter
is pressed.
An undo is possible as long as the projector is running on the same source (= same adjustment block) even when some adjustments
as geometry or convergence are already readjusted. When undo is presssed all settings are reset to the previous settings.
How to cancel 'Set to midposition' ?
When "All settings to midpos" is selected, all settings are set to their midposition. To cancel this action :
1. Push the cursor key é or ê to highlight 'Undo all settings to midpos' (menu 1).
2. Press ENTER to cancel the set to midposition action.
Press EXIT to cancel the procedure 'undo set to midposition'.
SET TO MIDPOSITION
R&B CONVERGENCE MID
GREEN CONVERGENCE MID
FOCUS TO MIDPOSITION
E-W TO MIDPOSITION
N-S TO MIDPOSITION
DIG VERT LINEARITY MID
DIG HOR LINEARITY MID
ASTIGMATISM MIDPOSITION
UNDO ALL SETTINGS TO MIDPOS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
8-17
Service Mode
Common Settings
What can be done ?
Within the common settings menu, the following items can be set up or executed :
- Dynamic Astigmatism
- Gamma Correction
- CRT run in cycle
- CRT Drive mode
- Memory banks : on/off
- Flyback turnover point
- Menu Position : standard/middle
How to select ?
1. Push the cursor key é or ê to highlight 'Common Settings' (menu 1).
2. Press ENTER to select.
The common settings menu will be displayed (menu 2).
SERVICE MODE
COMMON SETTINGS
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
menu 2
Dynaminc Astigmatism
What can be done ?
The spot shape adjustments correct the spot shape in 25 different areas on the screen for the three colors separately.
The spot shape is adjusted according to the axial axises and the diagonal axises when using the cursor keys on the RCU.
These adjustments have to be done on a dot pattern (external source or genlocked pattern).
Spot shapes
before dynamic
astigmatism correction
Diagonal
astigmatism correction
(use the
and
arrow key)
Spot shapes
after dynamic
astigmatism correction
Axial
astigmatism correction
(use the
and
arrow key)
image 1
8-18
5976194 BARCOCINE 9 31012002
Service Mode
Start Up
To start up the dynamic astigmatism :
1. Push the cursor key é or ê to highlight 'Dynamic Astigmatism' (menu 1).
2. Press ENTER to display the dynamic astigmatism menu (menu 2).
The dynamic astigmatism can be adjusted on the selected source or on pattern lock on the selected source (genlocked pattern).
The way of adjusting is the same for both ways and for each color. The explanation will only be given for one color.
COMMON SETTINGS
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
DYNAMIC ASTIGMATISM
ON SELECTED SOURCE
RED
GREEN
BLUE
ON GENLOCKED PATTERN
RED
GREEN
BLUE
FOCUSING ON CURRENT SOURCE
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
How to adjust ?
The adjustment of the dynamic astigmatism is done on the selected source or genlocked pattern and for each color separately.
The menu will be displayed hereafter for a genlocked pattern on the green image.
To adjust, follow the next procedure :
1. Push the cursor key é or ê to highlight 'green under Genlocked Pattern' (menu 1).
2. Press ENTER to display the dynamic astigmatism adjustment menu (menu 2).
The screen is divided into 25 areas (5 x 5) (menu 3). In each area, the spot shape can be adjusted.
3. Use the cursor keys to select the desired area.
4. Increase the contrast level using the Contrast Control to near maximum. Using that "+" Sharpness Key, defocus the image until
the dots are large and easily visible.
DYNAMIC ASTIGMATISM
ON SELECTED SOURCE
RED
GREEN
BLUE
ON GENLOCKED PATTERN
RED
GREEN
BLUE
DYNAMIC ASTIGMATISM
SEL : select area using arrow keys
ADJ : adjust axial astig. using ç or
è , diagonal astig. using é or ê.
Toggle between SEL and ADJ with
<EXIT>
Toggle between 4-POLE and 6-POLE
with <ENTER>
Use the <SHARPNESS> keys for the
defocusing of the image.
FOCUSING ON CURRENT SOURCE
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
<ENTER> to continue
<EXIT> to return
menu 2
5. Press EXIT to toggle the cursor keys from selection keys to adjustment keys.
6. Adjust first the 4 pole correction.
Adjust the spot shape in the axial or diagonal direction, using the cursor keys. Adjust until the spot shape is circular.
Use the cursor key é or ê for the diagonal astigmatism adjustment and the cursor key è or ç for the axial astigmatism adjustment.
7. Press ENTER to toggle from the 4 pole correction to the 6 pole correction or vice versa.
8. Adjust the spot shape again using the cursor keys.
9. Press EXIT to return to the area selection screen.
10. Repeat from step 3 as may times as necessary.
Focusing on current source
When selecting this function, the 'Focusing' menus from the random access will be displayed.
For more explanation, see Random Access Adjustment mode § Focusing.
5976194 BARCOCINE 9 31012002
8-19
Service Mode
Gamma Corrections
Gamma Corrections warning ?
'The Gamma Corrections are factory adjusted using an ACTAS colour analyser !
Therefore, only qualified installation or service personnel should perform these adjustments !'
A warning will be displayed on the screen as there is a risk of incorrect adjustment of the projector..
Start Up
To start up the gamma corrections :
1. Push the cursor key é or ê to highlight 'Gamma Corrections' (menu 1).
2. Press ENTER to start up.
A warning screen will be displayed (menu 2).
If you are qualified, press ENTER to continue. If not qualified, press EXIT to return to the Common Settings menu. Further description
of the Gamma Corrections are given in the Installation manual, Appendix C.
COMMON SETTINGS
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
WARNING
RISK OF INCORRECT ADJUSTMENT
OF THE PROJECTOR
THE GAMMA CORRECTIONS ARE
FACTORY ADJUSTED USING AN
ACTAS COLOUR ANALYSER !
THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS !
<ENTER> TO CONTINUE
<EXIT> TO RETURN
menu 2
CRT run in cycle
What can be done ?
Only necessary when a new picture tube is installed.
The CRT run in cycle option can only be activated when memory blocks on an internal # pattern are available. When one or more
such blocks are available, a flashing white image (5sec on, 5 sec off) is generated and that for 5 min on the first internal block. In
the next 5 min, a second internal block will be used to generate the flashing white image. The image will also be shifted in a vertical
way to prevent a CRT burn in. To quit the CRT run in cycle option, press EXIT.
How to select CRT run in cycle ?
1. Push the cursor key é or ê to highlight 'CRT run in Cycle' (menu 1).
2. Press ENTER to start up.
If a memory block adjusted on an internal # pattern is available, the CRT run in cycle will start. If no such a block is available,
the projector cannot run the CRT run in option and leaves the adjustment mode.
If you still want to run CRT run in cycle, create first a memory block on an internal # pattern and restart the CRT run in option.
COMMON SETTINGS
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
Select with é or ê
then <ENTER>
<EXIT> to return.
CRT RUN IN CYCLE
A flashing white pattern will be
generated until <EXIT> is pressed.
The projector only uses memory
blocks adjusted on an internal
# pattern; if no such block is
available, the projector can't run
the procedure and leaves the
adjusment mode.
<ENTER> to continue
<EXIT> to cancel
menu 2
menu 1
8-20
5976194 BARCOCINE 9 31012002
Service Mode
CRT Drive Mode
What can be done ?
The projector CRT's can be driven with the normal current (normal mode), a lower current (economic mode) or with a higher current
(boost mode). The higher the current, the higher the light output but the lifetime will shorten.
Available drive modes
-
Normal
Economic : Lower drive current to the CRT's, the lifetime of the CRT's will enlarge but the light output will reduce.
Tempory boost : Higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output will be higher. This
situation is tempory, when restarting the projector, the drive mode is automatically set to normal.
Permanent boost : Higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output will be higher. This
setting will be saved in the EEPROM. When restarting the projector, it will start up in boost mode.
How to change the drive mode ?
To
1.
2.
3.
2.
change the drive mode :
Push the cursor key é or ê to highlight 'CRT Drive Mode' (menu 1).
Press ENTER to display the CRT Drive mode menu (menu 2).
Push the cursor key é or ê to highlight the desired drive mode (menu 3).
Press ENTER to activate the selected drive mode.
COMMON SETTINGS
CRT DRIVE MODE
NORMAL
ECONOMIC
TEMPORARY BOOST
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
PERMANENT BOOST
WARNING : permanent
boost mode reduces the
lifetime
of the CRT's !
Select with é or ê
then <ENTER>
<EXIT> to return.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 2
menu 1
CRT Drive mode warning
A warning, permanent BOOST mode in use, will be displayed to inform the user.
When text is on, this warning will be repeated every time a new source is selected.
WARNING
PERMANENT
BOOST MODE
IN USE !
Memory banks
What can be done ?
The user has the possibility to create 8 different memory banks (formats) for each source. But, the maximum allowed quantity of
memory banks for all sources together is 32.
The option to create different memory banks for the same source can be switched ON or OFF.
How to select Memory Banks ?
1. Push the cursor key é or ê to highlight 'Memory Banks' (menu 1).
2. Press ENTER to toggle between ON and OFF.
ON : different memory banks available.
OFF : only one memory bank available.
If different memory banks are available for a source and the memory bank option is toggled to OFF, only the first memory bank
will be used to display the source.
COMMON SETTINGS
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
8-21
Service Mode
How to create a new memory bank ?
1. Select your source. The projector selects the last used memory bank.
2. Press ENTER
3. Push the corresponding digit (between 1 and 8) of a non existing memory bank. (The memory banks can be created in random
order, e.g. first creating bank 5 and later bank 2.)
4. Make the necessary adjustments. When leaving the source, the new created memory bank will be saved for later use.
Example : When source 1, video 15.6 kHz /60Hz is create on bank 4 and the vertical frequency changes to 50Hz, the projector will
create a new block (due to the vertical frequency change) with the same bank number 4.
How to recall a specific memorybank for the actual source ?
When the memory bank option is ON and a source is selected, this source will be displayed with the last used memory bank settings.
An on-screen menu will give a indication of the memory bank nummer used (menu 1).
To switch to another memory bank :
1. Press ENTER to select the next memory bank in increasing order.
or
2. Enter the number of the desired memory bank with the digit keys.
In both cases, the on-screen indication will be update.
SOURCE XX
MEMORY
BANK
4
menu 1
Flyback Turnover Point
What can be done ?
The horizontal flyback time for horizontal frequencies can be long or short. The turnover point from long to short can be installed
by the user himself.
Set Up of the Flyback Turnover Point
To set up the flyback turnover point :
1. Push the cursor key é or ê to highlight 'Flyback turnover point' (menu 1).
2. Press ENTER to display the flyback turnover point (menu 2).
The actual turnover point frequency will be filled in.
3. Select the digits with the left or right cursor keys and enter the new value with the digit keys on the RCU.
The flyback turnover point frequency should be somewhere between 90 kHz and 130 kHz.
4. Press ENTER to select.
COMMON SETTINGS
FLYBACK TURNOVER POINT
Enter new frequency :
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
0 9 0 kHz
Use the ç or è to select,
and reprogram with
numeric keys
Lowest point is 90 kHz.
Highest point is 130 kHz.
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
<ENTER> to confirm
<EXIT> to return.
menu 2
Menu Position
What can be done ?
The bar scale menu, warning and message boxes can be displayed in the right lower corner or in the middle of the screen.
8-22
5976194 BARCOCINE 9 31012002
Service Mode
How to change the position ?
To change the position :
1. Push the cursor key é or ê to highlight 'Menu position' (menu 1).
2. Press ENTER to toggle between STANDARD or MIDDLE.
COMMON SETTINGS
DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS
CRT RUN IN CYCLE
CRT DRIVE MODE
MEMORYBANKS : ON
FLYBACK TURNOVER POINT
MENU POSITION : STANDARD
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
I2C Diagnostics
What can be seen ?
The I2C diagnostics menu gives an overview of the I2C failures inside the projector.
To scroll through the failure list, push the cursor key é or ê .
The I2C address, IC number and module name will be given in I2C diagnostic menu.
When no errors are detected, the following message will appear on the screen :
"No errors on i2c-bus detected".
How to select ?
1. Push the cursor key é or ê to highlight 'I²C Diagnostics' (menu 1).
2. Press ENTER to display the diagnostic menu (menu 2).
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
I2C DIAGNOSTICS
Failures :
addr IC number mod.name
48H IC200
DECODER
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
Scroll with
or
then <ENTER>
<EXIT> to return.
menu 2
Voltage Diagnostics
What can be seen ?
The real value of the different voltages will be displayed on the voltage diagnostics menu.
How to start up ?
1. Push the cursor key é or ê to highlight 'Voltage diagnostics' (menu 1).
2. Press ENTER to display the voltage diagnostic menu (menu 2).
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
5976194 BARCOCINE 9 31012002
VOLTAGE DIAGNOSTICS
+17V : 16.9 Volt
-17V : -17.1 Volt
+9V : +9 Volt
+12V : +11.9 Volt
-12V : -11.8 Volt
+30V : +29.8 Volt
-40V : -39.8 Volt
+110V : +110 Volt
+210V : +209 Volt
HTHD :
-conv :
+conv :
foc_lo :
foc_hi :
<EXIT> to return.
menu 2
8-23
Service Mode
Projector Diagnostics
What can be seen ?
A log of the last 5 failures with the run time when the failure happened is consultable in the Projector Diagnostics.
How to display the Projector Diagnostics ?
1. Push the cursor key é or ê to highlight 'Projector diagnostics' (menu 1).
2. Press ENTER to display the projector diagnostic menu (menu 2).
The last failure will be displayed.
3. Use the cursor keys to scroll through the failure log.
4. Press ENTER to switch to the voltage diagnostics (menu 3).
5. Press EXIT to return to the projector diagnostics menu.
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
VOLTAGE DIAGNOSTICS
PROJECTOR DIAGNOSTICS
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
8-24
PROJECTOR DIAGNOSTICS
Failure nr : 2
Runtime : 180h 30 min
Projector block nr : 4
Coincidence : ON
Deflection :
OFF
SF
: yes
SF vert : no
SF hor : no
IBCL fail :no
EHT fail :no
HD EHT : no
Fan Fail : yes
Arrow keys to scroll,
<ENTER> to see the voltages,
<EXIT> to return.
menu 2
VOLTAGE DIAGNOSTICS
+17V : 16.9 Volt
-17V : -17.1 Volt
+9V : +9 Volt
+12V : +11.9 Volt
-12V : -11.8 Volt
+30V : +29.8 Volt
-40V : -39.8 Volt
+110V : +110 Volt
+210V : +209 Volt
HTHD :
-conv :
+conv :
foc_lo :
foc_hi :
<EXIT> to return.
menu 3
5976194 BARCOCINE 9 31012002
Programmable Function Keys
9
PROGRAMMABLE FUNCTION KEYS
Programmable Function Keys
What can be done with these keys
The five function keys on top of the remote control can be programmed as short cut keys (quick access) to almost any adjustment
function.
See list futher in this chapter.
How can a Function Key be programmed ?
A function key can only be programmed when in the service menus.
Handle as follow :
1. Scroll through the menus until the desired function is on the menu.
2. Select this function by pushing the cursor keys up or down.
3. Press the desired function key for this function.
The following message : "Programming Function Key Fx" will be displayed.
The message will disappear automatically and the function key is programmed.
4. Leave the adjustment mode by pressing ADJUST.
5. The function key is available in the operational mode.
e.g. programming horizontal phase on key F4.
1. Press ADJUST to enter the main menu (menu 1).
2. Push the cursor keys é or ê to select 'Service menu'.
3. Press ENTER to go into the adjustment menus.
A warning will be displayed (menu 2).
4. If qualified, press ENTER otherwise press EXIT and call for technical assistance.
5. Select Randon by pushing the cursor keys é or ê .
6. Press ENTER to display the Random Access mode menu (menu 3).
7. Push the cursor keys é or ê to select 'Geometry'.
8. Press ENTER to display the Geometry menu (menu 4).
9. Push the cursor keys é or ê to select H PHASE (menu 4).
10. Press 'F4' to program this key.
11. Press ADJUST to return to operational mode.
MAIN MENU
Image Control
IRIS Control
Sound Control
Function keys
Service Menus
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 1
ADJUSTMENT MODE
GEOMETRY
Select a path from below :
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
V SIZE
V LINEARITY
H SIZE
BLANKING
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE
PROJECTOR.
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Source 01
Select with é or ê
then <ENTER>
<EXIT> to return.
The following
SERVICE menus
are reserved to,
and to be performed only
by qualified personnel !
If qualified, press
<ENTER> to continue, or
if not, <EXIT> to return.
menu 3
Select with é or ê
then <ENTER>
<EXIT> to return.
menu 4
menu 2
5976194 BARCOCINE 9 31012002
9-1
Programmable Function Keys
9-2
5976194 BARCOCINE 9 31012002
Messages, warnings and failures
10
MESSAGES, WARNINGS AND FAILURES
INPUT 01
RGB2
Fh= 15.6 kHz
Fv= 050 Hz
When selecting a new source,
information about this source will
be displayed on the screen. Source
number, horizontal and vertical frequencies of the displayed source.
SOURCE 01
RGB2
Announcement of the selected
source.
WARNING :
input not
available
WARNING :
enter
password
xxxx
TEXT on
SOURCE 01
RGB2
xxxkHz
xxHz
TEXT off
PROJECTOR
ADDRESS :
003
WRONG
PASSWORD
!!!
Message to enter your password.
Password contains 4 digits.
These messages will be displayed
on the screen when pushing the
TEXT key.
Text ON : the 'bar scale indication'
will be enabled during the change
of an analog control in the 'operational mode' + all warnings and
failures will be displayed.
Text OFF : the 'bar scale indication'
will be disabled during the change
of an analog control in the 'operational mode' + all warnings and
failures will not be displayed.
Indication of the projector address
when activating the 'ADDRESS'
button on the RCU with a pencil or
other small object.
Message when the entered password is wrong.
source not
available
WARNING :
invalid
key entry
WARNING :
end of adjust range
When using the projector with the
RCVDS, this warning will be displayed when selecting an input
slot of an RCVDS where the input
board is missing.
The input is a valid input but the
source is not connected to the
input terminals or the input source
is switched off.
When a wrong key is pressed on
the RCU.
End of adjustment range.
WARNING :
input
no longer
available
The input source is no longer available.
WARNING :
RCVDS not
available
The input source selector is not
available.
WARNING :
invalid
frequency
input
The entered frequency or applied
frequency of the source is out of
the projector's range.
WARNING :
permanent
BOOST mode in
use !!!
The CRT drive mode is switched to
permanent boost.
WARNING :
Option not
installed !
Option not installed. e.g. Video
selected but no decoder installed.
WARNING :
The entered password is incorrect
Invalid Code Entry
5976194 BARCOCINE 9 31012002
10-1
Messages, warnings and failures
FAILURE
I2C error
addr. : 7FH3
FAILURE
short
circuit on
I2C bus
FAILURE
RCVDS communication
error
FAILURE
Hardware failure. Call a qualified
service technician for repair.
Hardware failure. Call a qualified
service technician for repair.
Serial communication error between the RCVDS and the
projector.
input not valid
invalid input
FAILURE
PC communication error
FAN FAILED
Projector will
switch off
FAILURE
IRIS II
configuration
failed
10-2
error in the communication between
the projector and the PC.
projector switched off due to a fan
fail.
Error occured while configuring
the IRIS II module.
5976194 BARCOCINE 9 31012002
Adjustment Blocks and Source Numbers 90-99
A
ADJUSTMENT BLOCKS AND SOURCE
NUMBERS 90 - 99
Adjustment Blocks (memory blocks)
What are adjustment block ?
As the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector’s memory as numeric
values. These numeric values are used to control digital potentiometers which in turn, control the projector. Each source connected
to the projector has a unique set of adjustment data which is automatically downloaded into the projector’s digital potentiometers once
the source has been selected. This set of adjustment data is referred to as an “adjustment block”.
An adjustment table is automatically created for a source when the source is first connected to the projector and the Adjustment mode
is entered. If other sources have already been connected to the projector and geometry and convergence adjustments have been
performed on these sources, the projector will use Linear Digital Interpolation to create a new block for the new source. This block
will provide an initial set of adjustments for the new source that have been calculated by the projector from “previous experience”.
The projector’s memory has the capacity to store 32 adjustment blocks. The adjustment block consists of two parts, the block header
and the data representing the values for all adjustments (eg. Convergence and Geometry) in the projector for the source the block
corresponds to. The block header contains the basic characteristics of the source and the projector configuration used to display
the source.
Built up of block
Block Header
example of block header
Block Number
Source Number
Horizontal Frequency
Vertical Frequency
Input Type
Scan Switch Configuration
01
01
15.6 kHz
50 Hz
video
Front/Ceiling
The data representing the various adjustments for the source follows the block header.
Source numbers 90 - 99
Why used ?
Source numbers 90 - 99 do not correspond to physical inputs to the projector or RCVDS. They are used to assign an additional
adjustment block to a source. This additional adjustment block may contain different geometry and convergence settings, sync fast/
slow positions and enhanced blue on/off settings. The relationship between source numbers 0 - 9 and 90 - 99 (projector with RCVDS)
or 1 - 5 and 91 - 95 (stand-alone projector) is shown in the diagram below.
The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting
the corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector). Once this source number is selected,
the alternate block of adjustment data is in use and may be modified via the adjust mode of the projector. The alternate adjustment
block is automatically stored.
How to create a second block ?
Follow the steps below to create a second adjustment block for a source between 0 and 9.
1. Select the source between 0 and 9 that the second adjustment block is to be created for.
2. Select the corresponding source number between 90 and 99. The adjustment block for the source number between 0 and 9 is
copied to the corresponding source number between 90 and 99.
3. Enter the adjust mode and make any desired changes (geometry, convergence, sync fast/slow, enhanced blue on/off) to the second
adjustment block.
4. Exit the adjust mode.
Note : the above also applies to source number 1 - 5 and 91 - 95 of a stand alone projector (no RCVDS)
5976194 BARCOCINE 9 31012002
A-1
Adjustment Blocks and Source Numbers 90-99
sou r c e
input 0
source
input 1
Block header A
source number 90
Block header A, different analog settings
source number 1
Block header B
source number 91
Block header B, different analog settings
source number 2
Block header C
source number 92
Block header C, different analog settings
○ ○ ○
source
input 2
source number 0
source
input 9
A-2
source number 9
Block header J
source number 99
Block header J, different analog settings
5976194 BARCOCINE 9 31012002