Miele W 2209I Technical data

Operating and Installation instructions
Rangehood
DA 3460
DA 3490
To avoid the risk of accidents
or damage to the appliance,
it is essential to read these
instructions before it is installed
and used for the first time.
en - AU, NZ
M.-Nr. 09 727 360
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Grease filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fitting and replacing the charcoal filter (optional accessory) . . . . . . . . . . . . . . . 18
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Positioning the appliance in the wall housing unit . . . . . . . . . . . . . . . . . . . . . . . . . 25
Attaching the lightshield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Weight of a lightshield matching existing furniture. . . . . . . . . . . . . . . . . . . . . . 29
Adjusting the building-in depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fitting the grease filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Set up for extraction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Set up for recirculation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Operation with control module DSM 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.
3
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on the safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This rangehood is designed for
domestic use and for use in similar
environments by guests in hotel or motel
rooms, bed & breakfasts and other
typical living quarters. This does not
include common/shared facilities or
commercial facilities within hotels,
motels or bed & breakfasts.
~ It must only be used to extract
vapours and remove odours from
cooking.
~ This appliance is not suitable for
outdoor use.
Any other usage is at the owner's risk.
Miele cannot be held liable for damage
resulting from incorrect or improper use
or operation.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
have been given supervision or
instruction concerning its use by a
person responsible for their safety.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions. This appliance is not a toy!
To avoid the risk of injury, keep children
well away and do not allow them to play
with it or to use the controls. They will
not understand the potential dangers
posed by it. They should be supervised
whenever you are working in the
kitchen.
~ Older children may use the
rangehood only when its operation has
been clearly explained to them and
they are able to use it safely. They must
be aware of the potential dangers
caused by incorrect operation.
~ Please be aware that on
rangehoods with halogen lighting, the
lamps will get very hot during use and
remain hot for some time after switching
off. To safeguard against burning, keep
children well away from the lamps at all
times.
4
Warning and Safety instructions
Technical safety
~ Before installation, check the
rangehood for visible signs of damage.
Under no circumstances should you
use a damaged appliance. A damaged
appliance is dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
on-site electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in any doubt.
~ The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly, and where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
~ Installation, maintenance and
repairs may only be carried out by a
Miele authorised person in accordance
with current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
– it is switched off at the isolator, or
– the screw-out fuse is removed (in
countries where this is applicable), or
– the mains fuse is disconnected, or
– it is switched off at the wall socket
and the plug withdrawn.
5
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ This rangehood must not be
installed and operated in mobile
installations (e.g. on a ship).
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the warranty.
~ Great care should be taken when
using the rangehood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas cooktops or ovens which draw air
in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Warning and Safety instructions
There must be adequate ventilation of
the room when the rangehood is used
at the same time as appliances burning
gas or other fuels.
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the rangehood
and the heater are in operation
simultaneously, an underpressure of
0.04 mbar (4 pa) is the maximum
permissible in the room.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter must be sought.
If the rangehood is being operated in
recirculation mode, the above
restrictions do not apply.
Ventilation can be maintained by air
inlets which must not be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the rangehood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
7
Warning and Safety instructions
Correct use
~ Never use an open flame beneath
the rangehood. To avoid the danger of
fire, do not flambé or grill over an open
flame.
When switched on, the rangehood
could draw flames into the filter. Fat
particles drawn into the rangehood
present a fire hazard.
~ When using the rangehood over a
gas cooktop, ensure that any burners in
use are always covered by a pan.
Switch the cooking zone off when a pan
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The rangehood can become damaged
when exposed to excessive heat.
~ Always switch the rangehood on
when a cooking zone is in use,
otherwise condensation may collect in
the rangehood, which could cause
corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc., do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the rangehood on fire.
~ Do not use the rangehood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
8
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ There is a fire risk if cleaning is not
carried out in accordance with the
instructions.
~ The rangehood can get very hot
during cooking due to heat rising from
the cooktop.
Do not touch the housing or the grease
filters until the rangehood has cooled
down.
~ Do not use a steam-cleaner to clean
this appliance. Pressurised steam
could reach the electrical components
and cause a short circuit.
~ CAUTION: Accessible parts may
become hot when used with cooking
appliances.
Warning and Safety instructions
Correct installation
Accessories
~ Refer to the cooktop manufacturer's
instructions as to whether a rangehood
may be operated above the cooktop.
~ Only use genuine Miele spare parts
~ The minimum safety distances
between the top of the cooktop and the
bottom of the rangehood given in the
"Appliance dimensions" section of this
booklet must be maintained, unless the
cooktop manufacturer states that a
greater safety distance is required.
and accessories with this appliance. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the warranty, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
If more than one cooking appliance is
fitted beneath the rangehood, and they
have different minimum safety
distances to the rangehood, select the
greater distance.
~ Follow the cooktop manufacturer's
instructions on the use of flammable
materials over the cooktop when
installing a wood or laminate lightshield
onto the rangehood.
~ Safety regulations prohibit the fitting
of a rangehood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from Miele or
from builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
~ Ensure exhaust ventilation complies
with all relevant regulations.
9
Description of the appliance
10
Description of the appliance
a Exhaust socket C 150 mm
h On/Off touch control for the fan
b Controls
i Touch controls to select the fan
power setting
c Grease filter
d Pull-out deflector plate
j Touch control for the cooktop
lighting
e Cooktop lighting
f Charcoal filter
(special accessory for recirculation
mode)
g Drop-down lightshield to conceal
control panel
The front of the deflector plate can be
fitted with a lightshield to match your
kitchen furniture.
11
Description of the functions
The rangehood works with
. . . air extraction:
. . . air recirculation:
(air recirculation conversion kit required)
The air is drawn in, cleaned by the
grease filter and then directed outside.
If the on-site ventilation system does
not have a non-return flap, then the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the rangehood
is switched off.
When the rangehood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
Please note, the performance of
this rangehood hinges greatly on
the installed ducting to vent the
vapours. Poor choice of ducting
results in poor rangehood
performance. For ducting
recommendations, please refer to
the relevant section in these
operating instructions or contact
a specialised installer.
12
The air is drawn in and cleaned first by
the grease filter and then by a charcoal
filter. The cleaned air is then recirculated
back into the kitchen.
Charcoal filters are available to order
from Miele or via the internet at
www.miele-shop.com (check availability).
See back cover for contact details and
"Technical Data" for model number.
Before using the rangehood in
recirculation mode, ensure that the
charcoal filter is in place; see
"Cleaning and care".
Operation
The rangehood is operated by pulling
out and pushing in the deflector plate.
To switch the fan on
^ Pull out the deflector plate.
The fan will come on at power setting 2.
The K symbol and the 2 light up.
To select a power setting
To switch the fan off
^ Push the deflector plate back in. The
next time the deflector plate is pulled
out, the rangehood will operate at
power setting 2 again.
or
^ Press the On/Off K touch control for
the fan.
^ To select a lower power setting,
press the "–" symbol, or to select a
higher power setting, press the "+"
symbol.
All the indicator lights will go out.
Depending on the intensity of the
cooking vapours, levels 1 to 3 are
usually sufficient for normal cooking.
or
Intensive setting
When the lighting is switched on, the
indicator light I lights up.
^ When frying or cooking food with a
strong aroma, you may wish to select
the Intensive setting "IS" (yellow
indicator light).
Pull the deflector plate right out to
achieve optimum extraction and to
prevent unnecessary noise levels.
To switch the lighting on
^ Pull out the deflector plate.
^ Press the touch control for the
lighting I.
To switch the lighting off
^ Push the deflector plate back in.
or
^ Press the touch control for the
lighting I.
The indicator light will go out.
13
Operation
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it always only runs for 10 minutes before
reverting automatically to setting 3.
^ To set this option, both the fan and
the cooktop lighting must be
switched off and the deflector plate
pushed in.
^ Press the – and + touch controls at
the same time for approx. 10
seconds until the power level
indicator light 1 lights up in the
display.
^ Then press in turn,
– the cooktop lighting touch control I,
– then the – touch control, and
– the cooktop lighting touch control I
again.
If Automatic switch-off is not activated,
the 1 and IS indicator lights will flash.
^ Press the + touch control to activate
the Automatic switch-off.
The indicator lights for fan power
levels 1 and IS will now light up
constantly.
Press the – control to deactivate the
Automatic switch-off function.
^ Press the On/Off control K to
confirm.
^ If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the original
setting.
14
Safety switch-off
If the rangehood hasn't been operated
for 10 hours, the fan will switch off
automatically. The lighting will remain
switched on.
^ Pressing the On/Off K touch control
will switch the fan back on again.
Cleaning and care
,Before any cleaning or
maintenance work is carried out,
disconnect the rangehood from the
mains supply. Ensure that
– it is switched off at the wall
socket and the plug is removed,
or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed
(in countries where this is
applicable).
,Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off. Do not
touch the surface directly when
changing a lamp, as grease particles
from your fingers will adhere to the
surface and damage it.
The halogen lamps can also be
damaged if water is used to clean
them.
Wait several minutes after switching
off before beginning cleaning.
Housing
General notes
The surfaces and controls are
susceptible to scratches and
abrasion. Please observe the
following cleaning instructions.
^ Wipe the surfaces dry using a soft
cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate the electronics and cause
damage.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents. These will damage
the surface material.
Important for appliances with
stainless steel housing
(This infomation does not apply to the
controls).
Stainless steel surfaces can be cleaned
with a proprietary non-abrasive
cleaning agent designed specifically
for use on stainless steel.
To prevent immediate resoiling, the
Original Miele care product for stainless
steel can be purchased from Miele or at
www.miele-shop.com (depending on
country). Apply sparingly with a soft
cloth following the instructions on the
packaging.
^ All external surfaces and controls can
be cleaned using warm water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
15
Cleaning and care
Controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long.
Remove soiling straight away.
Observe the "General notes" on
cleaning earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
Do not pull the grease filter
downwards to remove while it is at
the back of the canopy.
^ Push in the deflector plate.
Grease filter
The re-usable metal grease filter in the
appliance removes solid particles from
the kitchen vapours (grease, dust, etc.)
preventing soiling of the rangehood.
To avoid a build-up of fat, it should be
cleaned every 3-4 weeks on average,
or sooner if necessary.
,An oversaturated filter is a fire
hazard.
^ Grip the front of the deflector plate
together with the grease filter, and
pull outwards as shown.
^ Then lower the filter to remove.
To avoid damaging the filter or the
cooktop below, make sure you hold
the filter securely at all times when
handling it.
^ Slide the switch for the fan to position
“0”.
16
Cleaning and care
Cleaning the grease filter by hand
^ Clean the filter with a soft nylon brush
in a mild solution of hot water and a
little washing-up liquid.
Do not use undiluted washing-up
liquid.
Do not use:
^ After cleaning, leave the filter to dry
for a while on an absorbent surface
before putting it back in place.
^ When removing the filter for cleaning,
also clean off any residues of oil or
fat from the now accessible housing
to prevent the risk of these catching
fire.
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
Cleaning the grease filter in the
dishwasher
^ Place the filter as upright as possible
in the lower basket. Ensure the spray
arm is not obstructed.
^ Do not wash at more than 65 °C. If a
Miele dishwasher is being used,
select the Sensor wash programme.
^ Use a dishwasher detergent.
Depending on the cleaning agent
used, cleaning the filter in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filter in any way.
^ When putting it back, make sure that
the red plastic guides are at the
front and facing upwards.
^ Replace the grease filter in the front
of the deflector plate, press it
upwards and push it in together with
the deflector plate. It will slide onto
the fixing pins at the back. Finally,
push the grease filter back a little
more.
17
Cleaning and care
Fitting and replacing the
charcoal filter (optional
accessory)
If the rangehood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filter.
This is designed to absorb cooking
odours.
It is fitted in the canopy above the
grease filter.
Replacement charcoal filters can be
obtained from Miele or via the
internet at www.miele-shop.com
(depending on country).
See back cover for contact details,
and "Technical data" for type and
reference number.
Follow the instructions supplied with the
charcoal filter when fitting it.
Replace the charcoal filter at least
every six months or more frequently if
necessary.
Used charcoal filters can be disposed
of with the normal household waste.
18
Cleaning and care
Changing a halogen lamp
^ Pull out the deflector plate, and
remove the grease filter as described
earlier.
^ Switch off the fan and the lighting.
,Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off. Do not
touch the surface directly when
changing a lamp, as grease
particles from your fingers will
adhere to the surface and damage
it. Please follow the manufacturer’s
instructions.
^ Remove the charcoal filter if the
rangehood is being used in
recirculation mode.
,Before any cleaning or
maintenance work, disconnect the
rangehood from the mains supply.
Ensure that
– it is switched off at the wall
socket
and the plug is withdrawn, or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed
(in countries where this is
applicable).
^ Push down the lighting unit slightly
via the opening in the safety panel.
^ The halogen lamp is now accessible
to be unscrewed anti-clockwise.
^ Replace it with a new halogen lamp
(specification: GU/GZ 10, 230 V,
50 W). Screw the lamp into the
socket and push it upwards.
Please follow the manufacturer's
instructions.
^ Replace the grease filter and, if being
used in recirculation mode, the
charcoal filter.
19
Appliance dimensions
DA 3460
20
DA 3490
Appliance dimensions
1) In extraction mode: when measuring
for the height of the wall housing unit
and the cut-out, account must be taken
of any accessories fitted, e.g. silencer,
DSM module.
2) Recirculation is possible with
conversion kit DUU 151.
3) DSM 400 is available as an optional
accessory.
* Installation is also possible in a
600 mm wide wall unit.
Safety distances between cooktop
and rangehood (S)
The minimum safety distances
between the top of a cooktop and
the bottom of the rangehood are
as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:
Cooking appliance
Distance
S
Electric cooktop
600 mm
Open electric grill
650 mm
Deep fat fryer (electric)
650 mm
Multi-burner gas cooktop
with maximum 45.4 MJ/h
total output, with no burner
having a greater output
than 16.2 MJ/h.
650 mm
Multi-burner gas cooktop
with total output greater
than 45.4 MJ/h, or a gas
cooktop including a single
burner with an output
greater than 16.2 MJ/h.
760 mm
Single gas cooktop with a
maximum output of
21.6 MJ/h
650 mm
Single gas cooktop with a
maximum output greater
than 21.6 MJ/h
760 mm
See "Warning and Safety"
instructions for further information.
21
Installation
Installation accessories
22
Installation
a 1 exhaust connection
for exhaust ducting C 150 mm.
b 1 non-return flap
for fitting into the exhaust socket on
the motor unit (not needed for
recirculation mode).
c 2 brackets
to support the appliance in the wall
unit.
d 1 spacer strip
to conceal the gap between the rear
of the appliance and the wall.
e Conversion kit for recirculation
mode
including exhaust grille and flexible
aluminium hose with clip (the
conversion kit is not supplied with
the rangehood but is available as an
optional extra; see "Technical data").
f DML 400 installation kit (available
as an optional accessory)
contains hinging and screws for
attaching a lightshield to match
kitchen furniture (lightshield not
supplied with rangehood but is
available as an optional extra).
8 screws 4 x 15 mm
for securing the rangehood to the wall
unit.
8 screws M4 x 12 mm
for securing the rangehood to the
brackets.
4 of the screws can be used instead of
the plastic rivets to secure the spacer
strip.
2 screws 4 x 15 mm,
for securing the rangehood to the rear
wall.
4 plastic rivets
for securing the spacer strip to the rear
of the appliance.
23
Installation
24
Installation
Positioning the appliance in
the wall housing unit
To position the appliance correctly,
cut the spacer strip to the required
depth T, and then attach it to the
back of the appliance.
T= Wall unit depth K minus depth of
appliance G
^ Example a shows installation without
a lightshield and the front edge of the
pushed in deflector plate is aligned
with the front of the wall housing unit.
^ Screw the spacer strip to the bottom
of the sides of the housing, flush with
the rear wall.
^ Example b shows installation with a
lightshield to blend in with
surrounding kitchen furniture. The
installation position is adjusted by the
thickness b of the front panel plus
5 mm for the bracket DML 400.
^ Cut the spacer strip supplied to
measurement T.
Score along the groove for the
smaller measurement as shown, and
remove the surplus.
^ Draw a vertical line up both inside
walls of the housing from the front of
the spacer strip.
25
Installation
^ Screw the brackets onto the right and
left inside walls of the housing unit as
shown. The back edge of the
brackets should align with the vertical
line drawn up from the front of the
spacer strip, and the lower edge
aligned with the lower edge of the
housing unit side wall.
The brackets are designed for
furniture units with a thickness of 16
mm and 19 mm. Orientate the
bracket so that the vertical depth
matches the thickness of the panel,
as shown.
26
Do not remove the protective film
between the deflector plate and the
appliance housing until the
rangehood has been placed in the
housing unit.
The rangehood should be installed
without the grease filter fitted. If the
grease fitted, remove before installing
the rangehood (see "Cleaning and
care").
Installation
^ When installing a 90 cm wide
appliance in a 60 cm wide wall unit,
unscrew the brackets on the
deflector plate while it is pulled out.
Note for dismantling the rangehood:
Undoing the screws on the left and
right inside the housing releases the
brackets, allowing the appliance to
be removed from the unit.
^ Push the rangehood back against the
spacer strip.
^ Pull out the deflector plate.
^ Secure the appliance to the brackets
using 2 screws on each side.
^ Remove the protective film between
the deflector plate and the housing.
^ Lift the appliance up into the housing
from below, and engage in the
brackets.
27
Installation
^ Loosen the fixing bracket screws on
the top of the housing.
^ Align the housing unit and screw the
brackets onto the housing.
^ Push the brackets onto the rear of the
wall unit or the wall.
^ Secure the spacer strip to the back of
the appliance from behind using 4
plastic rivets as shown.
^ Secure the brackets to the rear wall.
If the rear wall of the wall unit is not
robust enough, the brackets must
be secured to the wall behind the
unit.
Ensure that the correct fixing
materials are used to do this.
28
Installation
Attaching the lightshield
Adjusting the building-in depth
^ Attach the lightshield (if using).
A DML 400 installation kit, available as
an optional accessory, is required for
this.
Follow the installation instructions
supplied.
Warning: Failure to install the screws or
fixing device in accordance with the
instructions may result in electrical
hazards.
^ The position of the deflector plate
can be brought forward by up to
35 mm using the adjusting screws on
either side of the canopy.
Then align the deflector plate with the
front of the adjacent furniture units.
Weight of a lightshield matching
existing furniture
The lightshield must not exceed 1300 g
in weight.
This applies to lightshields with a depth
of up to 30 mm.
For larger or heavier lightshields, the
weight must be reduced, e.g. by
trimming it down at the back.
29
Installation
Fitting the grease filter
^ Remove the protective strip around
the edge of the grease filter.
Fit the grease filter.
^ To do this, pull out the deflector
plate.
^ Turn the grease filter so that the red
plastic guides are at the front and
facing upwards.
^ Replace the grease filter in the front
of the deflector plate, press it
upwards and push it in together with
the deflector plate. It will slide onto
the fixing pins at the back. Finally,
push the grease filter back a little
more.
30
Set up for extraction mode
^ In case the on-site ventilation system
does not have a non-return flap, a
non-return flap is supplied with the
appliance. It must be fitted in the
exhaust socket in the motor unit.
Depending on the model, the
non-return flap may already be fitted.
^ When using C 150 mm ducting,
secure the exhaust connection
supplied to the exhaust ducting with
a hose clip.
Installation
Set up for recirculation mode
If site conditions are not suitable for the
rangehood to be used with air
extraction, the appliance must be set
up for recirculation.
For this, a conversion kit DUU 151,
available from Miele, is required.
^ Place the exhaust ducting on the
exhaust socket for the rangehood.
You will also need a charcoal filter (see
"Technical data").
^ See "Connection for air extraction" for
further instructions on fitting the
ducting.
^ A non-return flap is not required for
recirculation mode. Depending on
the model, it may already be fitted.
Pull the non-return flap out of the
exhaust connection.
31
Installation
Electrical connection
Refer to the notes in “Electrical
connection” and “Warning and
Safety instructions” before
connecting to the electricity supply.
^ Plug the connection cable into a wall
socket.
^ Fit the conversion kit as described in
the installation instructions supplied
with the kit.
^ Make sure that the slats on the
exhaust grille are directed towards
the middle of the room, and not
towards the wall or the ceiling.
A non-return flap is not used in
recirculation mode.
^ Fit the charcoal filter (see "Cleaning
and care").
32
Connection for air extraction
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the rangehood at the same time as
another heating appliance which
relies on air from the same room.
The rangehood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for the extraction ducting.
– The exhaust ducting should not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
– Where ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the rangehood.
– If the exhaust air is to be ducted into
the open air, the installation of a
telescopic wall vent or roof vent
(available as an optional accessory)
is recommended.
To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the
cross-sectional area must not be
smaller than the cross-sectional area
of the exhaust connection.
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Important:
If exhaust ducting with a diameter of
less than 150 mm, or if flat ducting is
used, the noise level of the
rangehood will increase and
extraction will be less efficient.
– All ducting, pipework and fittings
must be of non-flammable materials.
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
33
Connection for air extraction
Condensate trap
(optional accessory)
For installations in areas where the
exhaust ducting is exposed to cold
temperatures, we recommend
insulating the exhaust ducting and
installing a condensate trap to collect
and evaporate any condensate which
may occur. Condensate traps are
available for C 125 mm or C 150 mm
ducting.
When installing a condensate trap,
ensure that it is positioned vertically
and, if possible, directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.
34
Connection for air extraction
Silencer
(DASD 150, optional accessory)
...with air extraction:
To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system.
The silencer not only reduces noise
from the fan, but also sounds from
outside (e.g. traffic noise).
For this reason, the silencer must be
positioned as close as possible to where
the ducting leaves the building a.
...in recirculation mode:
The silencer needs to be positioned
between the fan and the exhaust grille
b. Ensure there is adequate space for
fitting it.
In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted in
the system.
35
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
Connection of this appliance should be
made via a suitable isolator which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
36
If the switch is not accessible after
installation, an additional means of
disconnection must be provided for all
poles.
For extra safety, it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.
Important
This appliance is supplied for
connection to an AC 230 V single
phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
Brown
= live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
If the connection cable is damaged, it
must be replaced by the manufacturer
or similarly qualified persons to avoid a
hazard.
Operation with control module DSM 400
The Miele DSM 400 can be used to
combine the rangehood with other
components.
Installation
Follow the installation instructions
suppled.
Warning: Failure to install the screws or
fixing device in accordance with the
instructions may result in electrical
hazards.
It enables the following:
Potential free connection
This is used for controlling another
appliance with the help of the
rangehood's On/Off button s.
If in any doubt, the advice of a
competent builder must be sought.
The control module must be installed
above the rangehood housing.
All electrical work must be carried
out by a competent, qualified
electrician.
Connection to a light switch
The control module can be used to
switch on the rangehood lighting via a
light switch in the house.
37
After sales service
In the event of a fault which you cannot
correct yourself, please contact:
– Miele
You will find the telephone number
and address of Miele on the back
cover of the manual.
Please quote the model and serial
number when contacting Miele. These
are shown on the data plate which is
visible when the grease filters are
removed.
Warranty
The warranty for this appliance is
2 years.
For further information, please refer to
your warranty booklet.
38
Technical data
Rated load . . . . . . . . . . . . . . . . . . 395 W
Fan motor . . . . . . . . . . . . . . . . . 295 W
Cooktop lighting . . . . . . . . . . 2 x 50 W
Voltage . . . . . . . . . . . . . . . . . AC 230 V
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
Fuse rating . . . . . . . . . . . . . . . . . . . 10 A
Electrical cable length . . . . . . . . . 1.5 m
Weight
DA 3460. . . . . . . . . . . . . . . . . . . 12.5 kg
DA 3490. . . . . . . . . . . . . . . . . . . 14.5 kg
Fan performance
Extraction power according to
EN 61591
Extraction system ø 150 mm:
Setting I . . . . . . . . . . . . . . . . . . 280 m3/h
Setting II . . . . . . . . . . . . . . . . . 420 m3/h
Setting III . . . . . . . . . . . . . . . . . 570 m3/h
Intensive setting . . . . . . . . . . . 720 m3/h
Recirculation with charcoal filter:
Setting I . . . . . . . . . . . . . . . . . . 220 m3/h
Setting II . . . . . . . . . . . . . . . . . 320 m3/h
Setting III . . . . . . . . . . . . . . . . . 420 m3/h
Intensive setting . . . . . . . . . . . 500 m3/h
Optional accessories for
recirculation mode:
- Conversion kit DUU 151
- Miele charcoal filter DKF13-1
39
Alteration rights reserved / 3513
M.-Nr. 09 727 360 / 01