Miele T 8007 WP Operating instructions

Operating instructions
for heat pump tumble dryer
T 8007 WP SUPERTRONIC
To avoid the risk of accidents or
damage to the appliance it is
essential to read these instructions
before it is installed and used for the
first time.
en - GB
M.-Nr. 09 459 300
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and should be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Disposing of your old
appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice.
Ensure that it presents no danger to
children while being stored for
disposal.
2
Energy saving tips
To avoid unnecessarily long drying
times and high consumption of energy:
– Make sure that your laundry is
thoroughly spun before drying.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
– Load according to the optimum
amount of laundry recommended for
the programme being used.
Underloading is uneconomical.
Overloading gives a poorer quality of
drying, and may cause unnecessary
creasing.
– Make sure that the room temperature
is not too high. If there are other heat
producing appliances in the room in
which the dryer is located, make sure
the room is well ventilated and switch
the other appliances off, if possible.
– After every cycle remove fluff from
the surfaces of the fluff filters.
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selector sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Structure of the main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Miele{home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Garment care label symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1. Sort the laundry and loading the drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2. Select a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Switch the dryer on with the K button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
– Programmes with drying levels (sensor drying) . . . . . . . . . . . . . . . . . . . . . . 25
– Programmes which operate by time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
– Other programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Select an extra option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Start at / Finish at . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3. Start the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Starting a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Time left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting a different programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start at / Finish at: Changing the time of day . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cancelling a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Adding or removing laundry after a programme has started . . . . . . . . . . . . . . 29
4. End of the programme - unload the drum . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3
Contents
Extra options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Freshen up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Gentle tumble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Favourite programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Emptying the condensed water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Make sure you clean all the filters at the correct intervals. . . . . . . . . . . . . . . . . . . 40
When to clean the surfaces of the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . 40
When to clean the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Cleaning the surfaces of the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cleaning with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Replacing the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Removing the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cleaning the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cleaning the cover for the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cleaning the heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Check and fault messages in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
An unsatisfactory drying result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Other problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Cleaning the cooling fins (bottom right grille) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
After Sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4
Contents
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Transporting the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Building under a continuous worktop/ in a row of kitchen units . . . . . . . . . . . . . 57
Levelling the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Arranging the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
External drainage via a sink or gully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Installation conditions requiring a non-return valve . . . . . . . . . . . . . . . . . . . . . 60
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Open the Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Language J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Drying levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Display / keypad illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Anti-crease. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5
Warning and Safety instructions
~ It is essential to read these instructions.
This tumble dryer conforms to current safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the tumble dryer,
please read these instructions carefully before using it for the first
time. They contain important information on its safety, installation,
use and maintenance.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
~ This tumble dryer is not designed for commercial use. It is
intended for use in domestic households and similar working and
residential environments.
~ The tumble dryer is not intended for outdoor use.
~ It must only be used as a domestic appliance to dry items which
have been washed in a water solution and which are marked on the
manufacturer's care label as being suitable for tumble drying. If
using dry cleaning kits, do so at your own risk, and follow the
instructions provided on the packaging.
Any other usage is not supported by the manufacturer and could be
dangerous. Miele cannot be held liable for damage resulting from
incorrect or improper use or operation.
6
Warning and Safety instructions
~ The tumble dryer can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience or
knowledge, if they are are supervised whilst using it or have been
shown how to use it in a safe way and understand the hazards
involved.
Safety with children
~ Children under 8 years of age must be kept away from the tumble
dryer unless they are constantly supervised.
~ Children 8 years and older may only use, clean or maintain the
tumble dryer without supervision if they have been shown how to do
so in a safe way and understand the hazards involved.
~ The tumble dryer is not a toy! To prevent the risk of injury, do not
allow children to play with it or near it, or to play with the controls.
7
Warning and Safety instructions
Technical safety
~ Before setting up the tumble dryer, check it for any externally
visible damage.
Do not install or use a damaged tumble dryer.
~ Before connecting the tumble dryer, ensure that the connection
data on the data plate (voltage and frequency) match the mains
electricity supply. If in any doubt, consult a qualified electrician.
~ The electrical safety of this tumble dryer can only be guaranteed
when correctly earthed. It is most important that this basic safety
requirement is observed and regularly tested, and where there is
any doubt, the household wiring system should be inspected by a
qualified electrician. Miele cannot be held liable for the
consequences of an inadequate earthing system (e.g. electric
shock).
~ Do not connect the tumble dryer to the mains electricity supply by
an extension lead. Extension leads do not guarantee the required
safety of the tumble dryer (e.g. danger of overheating).
~ If the electrical connection cable is faulty it must only be replaced
by a Miele approved service technician to protect the user from
danger.
~ Unauthorised repairs could result in unforeseen dangers for the
user, for which Miele cannot accept liability. Repairs should only be
undertaken by a Miele approved service technician, otherwise any
subsequent damage will not be covered by the guarantee. Ensure
current is not supplied to the tumble dryer until after maintenance or
repair work has been carried out.
~ Faulty components must only be replaced by genuine Miele
original spare parts. Only when these parts are fitted can the safety
standards of the tumble dryer be guaranteed.
8
Warning and Safety instructions
~ The tumble dryer must be isolated from the electricity supply in
the event of a fault and during cleaning and maintenance.
~ The tumble dryer must not be used in a non-stationary location
(e.g. on a ship).
~ Do not make any alterations to the tumble dryer, unless
authorised to do so by Miele.
~ Heat pump technology and refrigerant:
The heat pump in this tumble dryer uses a refrigerant which is
condensed by the compressor and led in a closed circuit through
the heat exchanger unit where heat exchange with the circulating
drying air takes place.
– The humming noises caused by the heat pump are normal and do
not impair the efficient functioning of the dryer.
– The refrigerant is not flammable or explosive.
– In general it is not necessary to leave the dryer standing for any
length of time before it is put into operation provided it has been
transported correctly (see "Installation").
However, if it has not been transported as described, ensure that
the recommended standing time prior to first operation is
observed. Otherwise the heat pump can be damaged.
~ In areas which may be subject to infestation by cockroaches or
other vermin, pay particular attention to keeping the tumble dryer
and its surroundings in a clean condition at all times. Any damage
which may be caused by cockroaches or other vermin will not be
covered by the guarantee.
9
Warning and Safety instructions
Correct use
~ To prevent the risk of fire, the following textiles must not be dried
in this appliance:
– items which have not been washed.
– items, such as workwear, which have not been thoroughly
cleaned and which are still soiled with grease, oil or other
deposits (such as cosmetics, lotions etc).
If items have not been thoroughly cleaned there is a danger that
these might self-ignite when heated, even after they have been
removed from the dryer at the end of the programme.
– items (e.g. mops and floor cloths) which have been treated with
inflammable cleaning agents or which contain residues of
acetone, alcohol, benzine, petrol, kerosene, stain remover,
turpentine, wax and wax remover or other chemicals.
– items which have been splashed with hair lacquer, hair spray, nail
varnish remover or similar substances.
When washing such heavily soiled items, ensure that you use
additional detergent and select a high temperature. If in doubt,
wash the items several times.
~ Remove all items such as lighters and matches from pockets.
~ Warning: Do not switch the tumble dryer off before the drying
programme has finished. If this is done, the laundry must be hung
up or spread out to cool it down.
10
Warning and Safety instructions
~ Danger.
This tumble dryer must not be connected to a controllable socket
(e.g. a timer switch or a peak load shut-off device).
If the dryer programme were to be interrupted before the end of the
cooling down phase, the laundry could self-combust.
~ To prevent the risk of fire, the following must not be tumble dried:
– items which have been cleaned using chemicals (e.g.
professional dry-cleaning agents).
– fabrics which contain a large proportion of rubber, foam rubber or
rubber-like materials. For example, products made from latex
foam rubber, shower caps, waterproof textiles, rubberised articles
and items of clothing and pillows with foam rubber filling.
– damaged items which contain padding or fillings (e.g. pillows,
jackets). When damaged, the filling can get out with the risk of
igniting in the dryer.
~ In many programmes, the heating phase is followed by a cooling
down phase to ensure that the items are not too hot to handle when
you remove them (this also avoids the danger of the laundry
self-igniting). The programme is not finished until the cooling down
phase has been completed.
As soon as the programme has finished, remove all laundry from the
drum.
~ Fabric conditioner and similar products must be used according
to the instructions on the manufacturer's packaging.
~ Do not let anyone sit or lean on the door, as this can cause the
tumble dryer to tip up.
~ Always close the door after use. This way you will avoid the
danger of:
– children climbing into the dryer or hiding things in it.
– pets or other small animals climbing into it.
11
Warning and Safety instructions
~ The tumble dryer must not be used:
– without the fluff filters in place or if the fluff filters are damaged in
any way.
– without the fine filters in place of if the fine filters are damaged in
any way.
This would cause an excessive build-up of fluff which in turn would
cause a fault.
~ After every cycle remove fluff from the surfaces of the fluff filters.
~ The fluff filters and the fine filters must be thoroughly dried after
cleaning. Damp or wet filters could cause operational faults.
~ Do not install the tumble dryer in a room where there is a risk of
frost occurring. At temperatures around freezing point the tumble
dryer may not be able to operate properly. There is a risk of damage
if the condensed water is allowed to freeze in the pump and in the
drain hose.
~ If the water is drained externally instead of being collected in the
condensed water container, make sure the drain hose is securely
attached if you hang it in a sink or basin to avoid the hose slipping
and the water causing damage.
~ Condensed water is not drinking water. It can cause health
problems in both people and animals.
~ Always keep the area around the tumble dryer free of dust and
fluff. Dust drawn into the tumble dryer can cause blockages in the
heat exchanger unit over time.
~ The tumble dryer must not be hosed down.
12
Warning and Safety instructions
Accessories
~ Only use genuine Miele original spare parts and accessories with
this tumble dryer.
If non-Miele parts are used, guarantee, performance and product
liability claims may be invalidated.
Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.
13
Operating the tumble dryer
Control panel
a Miele{home
Symbol for Miele|home enabled
appliance
b Information sensor :
The sensor lights up when
information about the menu in the
display is available.
c Service interface
This is used by service technicians
to run diagnostic checks on your
machine, or to update programming
data in the future.
d Selector sensors
A sensor is active when it is lit up.
See next page for more information.
e Display
–
–
–
–
–
–
14
For showing:
the functions selected
the programme sequence
information
error messages
the time of day
the position of an entry using the
scroll bar
f Clear sensor U
– For returning to the previous menu.
– For returning to the main menu when
touched twice.
– For deleting the values set
previously.
– For cancelling the programme.
g Start sensor
The programme selected is started
by touching this sensor when it is
illuminated green.
h K button
For switching the dryer on and off.
To save energy the dryer will switch
off automatically 15 minutes after the
end of the programme/anti-crease
phase or 15 minutes after the dryer is
switched on if it is not operated.
i / button
For opening the door. The dryer
does not need to be switched on at
the mains.
Operating the tumble dryer
Selector sensors
The selector sensors are on the left and right of the display.
They light up when they are active. The selector sensors are
used for the following:
Selecting an option
A dot (#) next to an option indicates that it can be selected.
The selector sensor on the left is active when the dot (#) is in
front of the word, the selector sensor on the right is active
when the dot (#) is behind the word or symbol.
Scrolling through the menus
If the menu lists more options than are visible in the display, a
scroll bar will appear on the right to show the position in the
list:
\
\
\
Main menu
10:21
$ Favourite programmes
# Cottons
[
m [
! Minimum iron
The sensors on the right can be used to scroll up or down the
list. Each touch of the sensor will move the list up or down
one line.
A dotted line will appear under the last option in the list.
Changing a value in the display
Time
+ $
10 :21
– #
OK !
[
[
[
Use the + and - sensors on the right to alter the value
highlighted. Once altered confirm the value with the lOK
sensor at the bottom right hand side.
15
Operating the tumble dryer
Favourite programmes
Programme sequence display
You can save up to ten of your own
customised programmes under names
of your choice.
Symbols in the display show which
section of the programme has been
reached.
Drying assistant
This helps you find the correct wash
programme. The drying assistant
guides you step by step so that you
can select the best programme for the
fabrics and garments you want to dry.
Settings menu
The Settings menu ! is used to alter the
tumble dryer's electronics to suit
different requirements. See "Settings
menu" for more details.
Information sensor :
The Information sensor : will light up if
information about an option is available.
Touch the sensor if you want to read
the information.
Symbol Programme sequence
R
G
Drying
I
Machine iron
G
Hand iron rr
H
Hand iron r
E
Normal
F
Normal+
7
Cooling down / Cancel
C
Cool air
D
Warm air
O
16
Start at / Finish at
Anti-crease/Finish
Operating the tumble dryer
Structure of the main menu
Favourite programmes
– Favourite programmes
(listed alphabetically)
– Create
– Change
– Delete
Cottons
– Minimum iron
– Delicates
– ....
– Drying level: (depending on programme)
– ....
– Duration (depending on programme)
– Extras (depending on programme)
– Start at
– Finish at
Drying tips
– Cottons*
– Delicates*
– Cotton + synthetic*
– Woollens
– Silks
– Microfibre*
– Linen*
* This option has further choices.
17
Operating the tumble dryer
Settings !
– Language !
– Time*
– Buzzer
– Drying levels*
– Code
– Keypad tone
– Brightness
– Contrast
– Display / keypad illumination
– Memory
– Anti-crease
– Miele|home**
– Remote control**
* This option has further sub-menus.
** Appears if the dryer has been fitted with the optional communication module.
18
Miele{home
a Communication-enabled appliances
Possible connections (optional)
b Communication module
g PC, Notebook
c SuperVision master appliance
h iPod* or iPhone*
d Power supply
i Connection with a domestic bus
system display
e Miele|home Gateway
f (WLAN) Router
j Possible internet conection
* iPod and iPhone are registered trade
marks of Apple Inc.
19
Miele{home
Depending on country, this appliance is
communication enabled and can be
linked into the Miele|home system via
a communication module b(optional
accessory).
Miele|home enabled appliances send
information via the household power
supply network d to the master
appliance c about the operational
status of the appliances, as well as
information about the progress of the
programme.
Displaying information, controlling
appliances
– SuperVision master appliance c
The status of other communication
enabled appliances in the system
can be shown in the display of the
SuperVision master appliance.
– Mobile terminal appliances g/h
A PC, Notebook or an iPod* /
iPhone* can be used within the
operating radius of a WLAN to
display status information about the
networked appliances and to carry
out some operational commands.
– Household network i
Miele|home enables smarter living.
With the Miele|home Gateway e
communication-enabled appliances
can be integrated into the domestic
bus system.
* iPod und iPhone are registered trade
marks of Apple Inc.
20
Optional accessories required
– Communication module
This must be fitted by a Miele service
technician.
– Miele|home Gateway
Both of these are supplied with their
own installation and operating
instructions.
Further information
For further information about
Miele|home, SuperVision and future
options please contact Miele.
Before using for the first time
Before using the dryer for the first time ensure that it is
correctly installed and connected. See "Installation".
,If the tumble dryer has not been transported as
described in "Installation" then it must be left to stand for at
least 1 hour before it is connected to the electricity supply.
Otherwise the heat pump may become damaged.
Preparing the dryer for use is done in five steps. The dryer
guides you automatically through steps 1. to 5.
1. Welcome screen
^ Switch the dryer on with the K button.
The welcome screen will appear in the display for 3 seconds.
The display for setting the language will then appear.
2. Set the language
\
\
\
Sprache
10:21
$ deutsch (
p
# english
! español
OK
!
[
[
[
^ Select the language you want.
^ The sensors on the right can be used to scroll up or down
the list.
^ Confirm the language you have selected with OK.
21
Before using for the first time
3. Set the time of day (if required)
Enter the time of day.
Time
+ $
10 :21
– #
OK !
[
[
[
^ Use + and - to set the hour.
^ Confirm with OK. Then set the minutes and confirm with OK.
4. Miele|home message
This communication enabled dryer can transmit programme
data through the power lines to the Miele|home system if it
has been fitted with a communication module (optional
accessory).
^ Confirm the message with OK.
5. Continue setting the dryer up as described in the Operating instruction manual.
The dryer is correctly set up once a programme lasting
longer than one hour has been run (See "2. Selecting a
programme").
The welcome screen and request to set the language will
appear in the screen after switching the dryer on again if a
programme lasting less than 1 hour was run.
^ Confirm the message with OK.
22
Notes on laundry care
Garment care label symbols
Drying
q/r Normal/low temperature
Drying is carried out at a low
temperature in every
programme, so you do not need
to sort your garments according
to whether they have the q or
r symbol.
s
Do not tumble dry
Tips on drying
– Always observe the maximum
recommended loads given in the
"Programme chart". Never overload
the drum.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
– Do not put soaking wet items into the
tumble dryer. Spin fabrics for at least
30 seconds before drying.
– Use the Automatic plus programme
for drying mixed loads of cotton and
minimum iron fabrics.
– Open jackets so that they can dry
evenly.
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the garment care
label, as the surface of the fabric
may otherwise become rough.
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry
these textiles. When purchasing
these garments it is advisable to take
their shrinkage properties into
account.
– Minimum iron fabrics tend to crease
more, the larger the load. This is also
the case for garments made from
very fine weave fabrics, such as
shirts or blouses.
Make sure you select a suitable
programme. If in doubt, divide the
garments into smaller loads and
select the Gentle tumble extra
option.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– New dark coloured garments should
be washed and dried separately
from light coloured garments to avoid
the danger of colours running and
discolouring other garments or even
plastic components in the dryer.
Dark coloured fibres can also settle
on light coloured garments and vice
versa.
– Use the Drying basket programme
for drying / airing items which are not
suitable for drying with mechanical
action. Important: You must use a
Miele drying basket (optional
accessory).
23
1. Sort the laundry and loading the drum
Prepare the laundry
Load the tumble dryer
To ensure an even drying result sort the
washed laundry according to:
..
. . . the drying level required,
. . . the type of fibre or weave,
. . . size,
. . . the moisture content after spinning.
^ Press the a button to open the
door.
,Make sure that objects, e.g.
detergent dispensing balls, have
been removed from the laundry.
They could melt and cause damage
to the dryer or the laundry.
– Check seams and stitching to ensure
that padding and linings are intact.
^ Load the laundry loosely into the
drum.
Do not overload the drum. See the
"Programme chart" for
recommended loads for each
programme.
Overloading can cause unnecessary
wear and tear to the laundry, and
give a disappointing drying result.
^ Before closing the door make sure
the fluff filter is correctly positioned.
– Fasten duvet covers, pillow cases
etc. to prevent small items from
being rolled up inside them.
– Fasten zips, hooks and eyes etc.
– Tie fabric belts and apron strings.
– Sew in or remove underwiring from
bras.
Check the laundry is right inside the
drum so that it cannot get trapped or
damaged when the door is shut.
^ Shut the door either with a gentle
swing, or lean against it and push it
shut.
24
2. Select a programme
Switch the dryer on with the K button
\
\
\
Main menu
10:21
$ Favourite programmes
# Cottons
[
m [
! Minimum iron
^ Select the programme you want: Use the right hand
sensors to show more programmes.
An additional menu may appear depending on the programme selected:
– Programmes with drying levels (sensor drying)
e.g. Cottons ... : You have a choice of drying levels with this
programme.
\
\
\
Cottons
1-8 kg 2:03 h
$ Drying level:
Normal
# Extras
# Start at
[
10:21
m [
^ Touch the Drying level sensor.
\
\
\
Drying levels
10:21
$ Normal (
# Hand iron r
! Hand iron rr
p
OK
!
[
[
[
^ If there are more than 3 levels to choose from: Use the right
hand sensors to show more levels.
^ Touch the left hand sensor to confirm the drying level
required.
^ Confirm with OK.
25
2. Select a programme
– Programmes which operate by time
e.g. Warm air ... : You have to select a duration.
\
\
\
Warm air
1-7 kg 0:20 h
$ Duration
0:25
h:min
10:21
+ $
– #
# Extras
OK !
# Start at
^ Touch the Duration sensor.
^ Use the + and - sensors on the right to alter the value
which is highlighted.
^ Confirm the value you have set with OK.
– Cool air:
20 mins
- 1 hour
– Warm air:
20 mins
- 2 hours
– Basket programme: 40 mins
- 2:30 hours
– Other programmes
e.g. Gentle smoothing ... : These programmes have fixed
drying levels / durations and cannot be altered.
\
\
26
Gentle smoothing 1 kg 1:06 h
$ Start at
# Finish at
10:21
[
[
[
2. Select a programme
Select an extra option
\
\
Extras
10:21
$ 9
Freshen up
# 8
Gentle tumble
OK !
[
^ Select the Extra you require.
When you select
– Freshen up the items are aired until they are at the Normal
drying level.
– Gentle tumble drum rotation is reduced for less
mechanical action.
A tick 9 will appear to show which Extra has been selected.
^ Confirm with OK.
Start at / Finish at
You can set the start (Start at) or the end (Finish at) time of
a programme.
The start and end time can be set in steps of 15 minutes. You
can delay the programme start time or the programme end
time up to a maximum of 24 hours. With the first 15 minute
step the time will be adjusted to the next quarter of an hour.
^ Select the Start at or the Finish at option.
\
\
\
Cottons
1-8 kg 2:03 h
10:21
+ !
$ Extras
# Start at
01:27
– !
! Finish at
03:30
OK !
[
[
[
^ Use + and - to select the time you want for Start at or Finish
at. Confirm the time you have selected with OK.
Please note: Selecting or deselecting an Extra or altering the
drying level subsequently, can postpone the programme end
time.
27
3. Start the programme
Starting a programme
^ Touch the green illuminated Start sensor.
Cottons
G
10:21
Normal - Extras (See :)
Time left: 2:03 h
Change !
[
– The time left counts down in the display.
– Symbols in the display show which section of the
programme has been reached.
Time left
The following factors all affect the estimated time left: the
residual moisture after spinning; the type of textile; the load;
the ambient room temperature; fluctuations in the power
supply or a programme interruption.
The time left is continually monitored and altered during
drying. This is why the time shown in the display may
fluctuate during the programme. This is quite normal.
Programmes can also finish earlier than expected, if, for
example, particularly fine fabric is being dried, the load is
very small or items were partially dry beforehand.
Some changes can be made after starting a programme:
Selecting a different programme
You cannot change to another programme once a
programme has started (this prevents unintentional
alterations).
You will need to cancel the current programme before you
can select a new one.
Start at / Finish at: Changing the time of day
^ Touch the Change sensor.
^ Select the Start at or the Finish at option.
^ Use + or - to alter the time of day.
^ Confirm the time you have selected with the OK sensor.
28
3. Start the programme
Cancelling a programme
^ Touch the U sensor.
Cottons
:
\
10:21
Cancel programme?
! Continue
Cancel !
[
^ Select Cancel.
The items will be cooled down 7, depending on the
temperature reached and how long they have been dried
for.
If you select U and Cancel again, O Finish will appear in
the display.
^ Press the s button to switch the dryer off.
^ Press the s button to switch the dryer on.
^ Select another programme and start it.
An alternative way to cancel
^ Press the a button.
Adding or removing laundry after a programme has started
^ Press the a button.
^ Open the door.
^ Add or remove items as required.
^ Close the door.
^ Select a programme.
^ Touch the Start sensor.
29
4. End of the programme - unload the drum
Before the end of a programme
There is a cooling down phase at the
end of the drying sequence: 7 (=
Cooling down) appears in the display.
The programme is not finished until the
cooling down phase has been
completed.
End of the programme - unload the
drum
O Anti-crease and Finish will appear in
the display to indicate that the
programme has finished. The buzzer
will sound at intervals.
The dryer has an energy saving mode:
After the programme has finished, the
display will go out and the Start sensor
will flash slowly (see also "Settings
menu - Display / Keypad illumination".
During the Anti-crease phase, the drum
will rotate at intervals to prevent laundry
creasing. This is quite normal.
^ Press the a button to open the
door.
^ Remove the laundry.
Check that all items have been
removed from the drum. If items are
left in the dryer, they could be
damaged by overdrying when the
dryer is next used.
The dryer will switch off automatically
15 minutes after the end of a
programme / the end of the anti-crease
phase.
(If the dryer is signed on to the
Miele|home system, it will not switch
off automatically).
30
^ Press the s button to switch the
dryer off.
The buzzer will sound.
^ Close the door.
^ Empty the condensed water
container unless the dryer has been
connected for external drainage, in
which case it does not have to be
emptied.
Drum lighting
To give a good view of the inside of the
drum so that no items are overlooked:
The lighting comes on when the door is
opened if the dryer is switched on. It
will go out after a short while if the door
is left open and after the door is closed
to save energy.
Extra options
The drying air is heated up for a
specific length of time. After this, the
garments are aired to the Normal
drying level without any more heat
being added.
Use the Freshen up extra option to
eliminate or reduce unwanted smells in
clean (dry or damp) clothing. Items
must be suitable for drying in a tumble
dryer. Dampen the garments a little
beforehand or add a fabric conditioner
sheet. Odours will not be removed as
effectively from any parts of the
garments which are made of synthetic
fibres.
This dryer offers the following extras:
ble
tum
p
nu
he
Gentle tumble
e
ntl
Ge
Optional extras
s
Fre
Freshen up
Cottons
#
#
Minimum iron
#
#
Shirts
#
#
Denim
#
#
Sportswear
#
Warm air
#
However, you have to choose either the
Freshen up or Gentle tumble option.
For drying items which can be dried in
a tumble dryer but which are
particularly susceptible to creasing or
which are not suitable for drying with a
great deal of mechanical action. When
this option is selected, the drum will
rotate less frequently.
The programme duration is longer.
Note
You can alter the drying levels for some
programmes (see "Settings menu").
This dryer also has a buzzer and an
anti-crease phase at the end of the
programme which can be altered (see
"Settings").
31
Favourite programmes
You can save up to ten programmes with the settings you
have selected for them under names of your choice. The
name can have up to 12 characters.
The favourite programmes which have been set are stored
alphabetically.
To save a favourite programme
There are two ways of saving a programme as a favourite.
1. Open the Favorite programmes menu and select Create.
You can then select a programme in the usual way.
2. If you alter a drying level or select an Extra when you
select the programme: Also select Save as.
To enter a name for a favourite programme
Name: ? A A A A A A A A A A A
\
\
10:21
) A B C D E F G H I J K L M N O P Q R S *
!
[
Select character
^ Select the first character and confirm this with Select
character.
Use the * sensor to scroll to the right to select the rest of
the characters.
^ After the first letter in upper case has been entered the
display will change automatically to display letters in lower
case. After a space has been entered the display will revert
to upper case again.
32
Favourite programmes
To save a name for a favourite programme
\
\
\
Name: D r y _ _ _ _ _ _ _
$
Space
10:21
Delete character
) g h i j k l m n o p q r s t u v w x
!
Select character
y
$
*
Confirm name
!
[
[
[
^ Select Confirm name.
To select a favourite programme
^ Call up the Favorite programmes menu. The saved
programmes will appear in alphabetical order.
^ Select the favourite programme you want.
^ Touch the green illuminated Start sensor. The programme
will start.
To change a favourite programme
^ Select the Change option.
^ Select the favourite programme you wish to change.
^ Make any changes and then save it under the same name.
The altered parameters will be active the next time the
favourite programme is started.
To delete a favourite programme
If you have already saved ten favourite programmes then you
will have to delete one of them before you can save a new
programme.
^ Select the Delete option.
^ Select the favourite programme you wish to delete.
^ Confirm the deletion.
33
Programme chart
Cottons
Max. load 8 kg*
Extra dry, Normal+, Normal**
Use for Single and multi-layered cotton fabric such as Towelling, T-shirts,
underwear, flannelette bed linen and baby clothes.
Notes
– Select Extra dry for multi-layered and very thick fabrics.
– Do not use Extra dry for loopknit fabrics (e.g. T-shirts, underwear,
baby clothes), as they have a tendency to shrink.
Hand iron r, Hand iron rr, Machine iron
Use for Cotton or linen fabrics e.g. Table linen, bed linen, starched laundry.
Note
To prevent laundry from drying out, it should be rolled up until you are
ready for ironing.
Minimum iron
Max. load 3.5 kg*
Normal+, Normal, Hand iron r
Use for Minimum iron cotton, synthetic and mixed fibre fabric. e.g. tops,
dresses, trousers, skirts and table cloths.
Delicates
Max. load 2.5 kg*
Normal+, Normal, Hand iron r, Hand iron rr
Use for Synthetic, mixed fibre, rayon and easy care cotton, e.g. shirts, blouses,
lingerie and appliquéd garments.
* Weight of dry laundry
Note for test institutes:
– ** Test programme (without selecting any Extra options) in accordance with
Regulation 392/2012/EU for energy labelling measured in accordance
with EN 61121.
– When selecting the Cottons programme, drain the condensed water away
through the drainage hose.
34
Programme chart
Automatic plus
Max. load 5 kg*
Normal+, Normal, Hand iron r
Use for
Mixed loads of garments suitable for the Cottons and Minimum iron
programmes. Sort according to colour.
Shirts
Max. load 2 kg*
Normal, Hand iron r
Use for
Shirts and blouses.
Denim
Max. load 3 kg*
Normal, Hand iron r
Use for
Denim garments, e.g. jeans, jackets, skirts, shirts.
Express
Max. load 3.5 kg*
Extra dry, Normal+, Normal, Hand iron r, Hand iron rr, Machine iron
Use for
Fabrics which can tolerate high temperatures and which can be dried
using the Cottons programme.
Note
– Short programme duration.
Woollens
Max. load 2 kg*
Use for
Woollen garments and fabrics containing wool blends.
Notes
– This programme only fluffs up woollen garments. They are not dried
completely.
– Remove garments as soon as the programme has finished.
Silks
Max. load 1 kg*
Use for
Silks (those suitable for drying in a tumble dryer), e.g. blouses and
shirts.
Notes
– Smooths out creasing.
– Remove garments as soon as the programme has finished.
* Weight of dry laundry
35
Programme chart
Sportswear
Max. load 3 kg*
Normal+, Normal, Hand iron r
Use for
Sportswear which is suitable for drying in a tumble dryer.
Outerwear
Max. load 2.5 kg*
Normal, Hand iron r
Use for
Outerwear which is suitable for drying in a tumble dryer.
Cottons hygiene
Max. load 3.5 kg*
Normal
Use for
Cotton and linen fabric which is in direct contact with the skin, e.g.
underwear, baby clothes, bed linen, towelling.
Note
The temperature is held constant for a longer period of time (longer
temperature holding time) to deactivate micro-organisms, e.g. bacteria
or house dustmites, and also to reduce the number of allergens in the
laundry.
To ensure that the micro-organisms are deactivated, do not interrupt
the programme.
Proofing
Max. load 2 kg*
Normal
Use for
Drying microfibre fabric, skiwear, fine, closeweave cotton garments
(poplin) or tablecloths which are suitable for drying in a tumble dryer
and have been treated to provide a water and dirt resistant finish.
Notes
– This programme includes a proofing fixing phase.
– Only use proofing agents containing fluorochemical compounds
which are stated by the manufacturer as being "suitable for use on
membrane textiles".
– Do not dry items which have been treated with proofing agents
containing paraffin. Fire hazard.
* Weight of dry laundry
36
Programme chart
Pillows
1-2 pillows up to 80 x 40 cm
Large pillows
1 pillow up to 80 x 80 cm
Normal
Use for
Pillows suitable for drying in a tumble dryer, with feather, down or
synthetic fillings.
Note
Please observe the instructions on the care label. Pillows can still feel
damp after being dried. You can use this programme several times
until the pillow feels dry.
Gentle smoothing
Max. load 1 kg*
Use for
– Cotton and linen fabric
– Minimum iron mixed fibre, cotton or synthetic fabric, e.g. trousers,
anoraks, shirts
Notes
– Suitable for dry and damp laundry.
Dry garments are time-controlled, damp garments are smoothed to
the Hand iron stage.
– Smooths out creasing caused during the spin cycle in the washing
machine.
– Remove garments as soon as the programme has finished so that
they are easy to iron.
* Weight of dry laundry
37
Programme chart
Cool air
Use for
Max. load 7 kg*
Any item which only needs airing.
Warm air
Max. load 7 kg*
Use for
– Drying voluminous and multi-layered fabric whose layers have
different drying characteristics, e.g. jackets, pillows.
– For drying individual items, e.g. bath towels, swimwear,
tea-towels.
Note
– Do not select the longest drying time to start with. Check the
items as you are drying them to find the optimum time.
Basket programme
Max. load for basket: 3 kg
Notes
– The drum does not rotate in this
programme.
For this reason, airing and drying may
only be carried out if the Miele drying
basket (optional accessory) is fitted in
the drum.
– Use this programme to dry items which
are suitable for drying in a tumble dryer
but which are not suitable for drying using mechanical action.
– A satisfactory drying result cannot be achieved without the drying
basket.
– It is essential to observe the operating instructions for the drying
basket.
Use for
See the operating instructions supplied with the drying basket.
* Weight of dry laundry
38
Cleaning and care
Emptying the condensed water
container
The condensed water will be collected
in the condensed water container.
Empty the condensed water
container after every drying
programme.
If the maximum level of the condensed
water container is reached
– the programme will be cancelled.
– Empty the container will appear in
the display.
To delete the message:
^ Switch the dryer off and then on
again.
^ Empty the container.
^ Replace the container in the dryer.
,Condensed water should not be
consumed. It could lead to health
problems for people and animals.
Condensed water can be put to
household use (e.g. in a steam iron or
humidifier). To ensure that any residual
particles of fluff in the condensed water
are removed before use, pass it
through a fine sieve or paper filter first.
^ Pull out the condensed water
container.
^ To prevent water running out, hold it
at the front and towards the back and
keep it in a horizontal position when
carrying it.
39
Cleaning and care
Make sure you clean all the
filters at the correct intervals
This tumble dryer has a multi-stage
filter system, consisting of the fluff
filters and a fine filter.
When to clean the fine filter
Only clean the fine filter when Clean
the plinth filter which is located in
front of the heat-exchanger appears
in the display.
– This dryer must not be used
without the fluff filters or fine filter
in place.
The grille in the bottom right must
always be in place.
– Make sure that the fluff filters and
the fine filter are not damaged.
Replace them immediately, if they
are damaged in any way (optional
accessories).
,If the above instructions are not
observed, an excessive build-up of
fluff can occur which in turn can
cause a fault.
When to clean the surfaces of the
fluff filters
Clean the surfaces of the fluff filters
after each drying programme.
The fluff filters located in the door
and the door opening collect fluff
from items being dried.
^ See "Cleaning the surfaces of the fluff
filters".
40
The plinth filter is located on the left
of the dryer behind the panel.
It collects finer fluff, hair and
detergent residues which have got
through the surfaces of the fluff filters
in the door and the door opening.
^ See "Fine filter".
^ To delete the message: Touch the
OK sensor.
Cleaning and care
Cleaning the surfaces of the
fluff filters
When to clean
Clean the surfaces of the fluff filters
in the door and the door opening
after each drying programme.
Cleaning them whilst dry
Note: You can also use a vacuum
cleaner to remove the fluff.
^ Use your fingers or a vacuum cleaner
to remove the fluff from the surface of
1 Fluff filter
2 Door seal
^ Open the door and pull the fluff filter
(1) out of the door as illustrated.
^ Remove any fluff from the hollow part
of the door with a bottle brush or a
vacuum cleaner.
^ Also clean the door seal (2) with a
damp cloth.
the filter.
^ Use your fingers or a vacuum cleaner
to remove the fluff from the two fluff
filters in the door opening.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.
^ Close the door.
41
Cleaning and care
Cleaning with water
If there is a great deal of compacted
fluff on any of the filters, they can be
removed and cleaned under hot
running water.
^ Open the door and pull the fluff filter
out of the door as described
previously.
The two filters in the door opening can
also be removed if you need to clean
them with water.
Replacing the filters
,Do not replace the filters if they
are damp or wet. Damp or wet filters
could cause operational faults.
^ Push the large filter back into the
door holder until it clicks into position.
Ensure it is facing the correct way.
^ Replace the filters in the door
opening by first inserting them at the
bottom and then pressing them into
place at the top.
^ Lock both dials (you will hear them
click).
^ Turn dial a until you hear it click.
^ Pull the filter by the dial out of the
door opening as shown b. Do the
same on the other side.
^ Rinse the filters under hot, running
water.
^ Dry the filters thoroughly with care.
^ Also clean the airways underneath
them, e.g. with a vacuum cleaner.
42
Cleaning and care
Fine filter
When to clean
Only clean the fine filter when Clean
the plinth filter which is located in
front of the heat-exchanger appears
in the display.
^ To delete the message: Touch the
OK sensor.
Removing the fine filter
^ Pull the filter out by the handle.
^ Switch the dryer off.
On the front left of the tumble dryer:
^ Pull the handle out of the filter.
Cleaning the fine filter
^ Press to open the access panel for
the fine filter (see arrow).
^ Clean the fine filter thoroughly under
running water.
The panel will spring open.
^ Then squeeze it thoroughly.
,It must not be replaced dripping
wet as this can cause a fault.
^ Use a damp cloth to remove any fluff
from the handle.
43
Cleaning and care
Cleaning the cover for the fine filter
Cleaning the heat exchanger
,Danger of injury.
Do not touch the cooling fins. You
could cut yourself.
,Prevent damage.
Carefully pass the vacuum cleaner
brush over the surface, without
applying any pressure.
Otherwise the cooling fins or the
struts in front of them could become
damaged.
^ Use a damp cloth to remove any
fluff. Make sure that you do not
damage the rubber seal when doing
this.
Visible soiling:
^ Check whether the cooling fins are
blocked with fluff (as follows).
^ Remove any visible soiling carefully
with a vacuum cleaner using a
dusting brush or a narrow crevice
nozzle.
44
Cleaning and care
Replacing
The filter must be fitted correctly and
the access flap closed to ensure
that water cannot leak from the
condenser system and to ensure
that the dryer functions efficiently.
Cleaning the tumble dryer
Disconnect the dryer from the mains
electricity supply.
^ Fit the filter back on the handle. Make
sure it is the correct way round.
To ensure that the filter is positioned
correctly in the front of the heat
exchanger unit:
^ Clean the housing, control panel and
door seal with a slightly damp cloth
and a mild detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable
proprietary stainless steel cleaner
following the manufacturer's
instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic sufaces and other
parts.
^ Dry all parts with a soft cloth.
^ First insert the handle with the filter
attached over the two guide pins.
Make sure that the yellow dot on
the handle is on the right.
^ Push the filter in completely.
^ Close the access flap.
45
Problem solving guide
With the help of the following notes minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical appliances should only be carried out by a
suitably qualified person in strict accordance with current local and national
safety regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
Check and fault messages in the display
Problem
You are asked to enter a
code.
1
Adjust the load
The programme is
cancelled, the buzzer
sounds.
N
Empty the container
Empty the container or
check the drain hose.
The programme is
cancelled, the buzzer
sounds.
46
Possible cause
Remedy
Access via a code has Enter the code (see
been activated.
Settings menu).
This is not a fault.
The electronic unit has
recognised that there
is no laundry or
insufficient laundry in
the drum and
cancelled the
programme. Drying
individual garments or
items which are
already dry can also
cause the programme
to be cancelled.
Use the Warm air
programme for drying
individual items.
– Open and shut the
door.
The condensed water – Empty out the
container is full or there
condensed water
is a kink in the drain
container or check the
hose.
drain hose.
To delete the message:
– Switch the dryer off
and then on again.
Problem solving guide
Problem
:
Clean the plinth
filter which is
located in front of
the heat-exhanger
appears at the
end of a
programme.
;
Fit plinth filter
Fit the plinth filter
appears and the
programme
cannot be
started.
;
Technical fault
F1
Comfort cooling
Possible cause
Remedy
This is a reminder to
clean the fine filter in
front of the heat
exchanger unit under
running water.
– Clean the fine filter. See
"Cleaning and care".
To delete the message:
– Touch the OK sensor.
The fine filter is
missing or has been
replaced the wrong
way round.
– Replace the fine filter
correctly.
– See "Cleaning and care".
Removing the fine
filter during a drying
cycle will cause the
programme to be
cancelled.
A programme cannot
be started while there
is a fault message in
the display.
– Switch the dryer off and then
on again.
The programme has
finished but the
laundry is still being
cooled down.
– Make a note of what is shown
in the display.
– Switch the dryer off and then
on again.
– If a programme still cannot
be started, Call Miele Service.
– You can either unload the
drum and leave the laundry
to cool at room temperature
or leave it in the dryer to
continue cooling.
47
Problem solving guide
Problem
,
Clean out airways
Possible cause
The cool air intake
panel is blocked.
Remedy *
– Move any objects, such as
a laundry basket, away
from the grille.
– Open a door or window to
keep the room temperature
down.
– Wait until the room has
cooled down before
restarting the programme.
appears after a
programme has
been cancelled. The temperature in
The laundry is
the room has risen
not properly dry. sharply.
To prevent the heat
pump overheating,
the dryer has
cancelled the drying
process with a
cooling down phase.
An excessive amount – Check and clean the
of fluff has built up.
surfaces of the fluff filters
and the fine filter.
Use a vacuum cleaner dusting
brush or small crevice nozzle
to vacuum up any soiling
carefully:
– From the heat exchanger
unit, bottom left (see
"Cleaning and care").
A prompt which has not A programme cannot – Follow the instructions in
the display.
been described
be started while there
is a fault message in – If a programme still cannot
previously appears in
the display.
the display.
be started, call Miele Service.
* To delete a fault message: Switch the dryer off and then on again.
48
Problem solving guide
An unsatisfactory drying result
Problem
The laundry is not
sufficiently dry.
Possible cause
The load consisted of
different fabrics.
Feathers are a natural
product and this is quite
normal.
Items made of synthetic Synthetic fibres tend to
fibres are charged with attract static charge.
static electricity after
drying.
Feather filled pillows
smell after drying.
Remedy
– Finish drying using the
Warm air programme.
– Select a different
programme next time*.
The smell will dissipate
after sufficient airing.
Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
programme or a fabric
conditioner sheet to the
load when drying.
Fluff is collected by the
fluff filters and can be
removed easily (see
"Cleaning and care").
Fluff is principally the
result of friction when
garments are being worn
and to some extent when
they are being washed.
Machine drying hardly
causes any fluff to form
and has no appreciable
effect on the lifetime of
the fabric.
* You can alter the drying levels for some programmes (see "Settings menu").
There is a build-up of
fluff.
49
Problem solving guide
Other problems
Problem
The drying
process goes
on too long or
even switches
off.
Possible cause
Remedy *
Ventilation to and from the
dryer may be insufficient,
e.g. because it is installed
in a room which is too
small. This can cause the
temperature in the room to
rise sharply.
– Detergent residues, hair
and fine fluff can clog the
fluff filters and the fine
filters.
– The cooling ribs can be
clogged.
Open a door or window while the
dryer is in operation for increased
air flow.
– Clean the fluff filters and fine
filter.
– Remove any visible fluff:
. . . From the heat exchanger
unit, bottom left, behind the flap
in the heat exchanger cavity
(see "Cleaning and care").
. . . From the cooling fins
behind the grille, bottom right
(see this section).
The cool air intake (bottom Move any objects, such as a
right grille) is blocked.
laundry basket, away from the
grille.
The fluff filters and fine filter The fluff filters and fine filter must
were wet when replaced.
be dry.
The laundry has not been
Make sure that your laundry is
spun sufficiently.
thoroughly spun at the
appropriate spin speed in the
washing machine.
The tumble dryer has been Do not exceed the maximum load
overloaded.
for the programme selected.
– Open zips next time.
Metallic components, e.g.
zips have prevented the
– If the problem occurs again,
dryer from registering the
dry garments with long zips
correct moisture level in the
using the Warm air programme
laundry.
(timed drying).
* Switch the dryer off and then on again before starting the programme.
50
Problem solving guide
Problem
Possible cause
Remedy
These noises are quite
normal and do not indicate a
fault.
The display and the
The display and sensor – Touch the Start sensor.
sensors are not lit up illumination switch off to
The display and sensors
and the Start sensor is save energy.
will light up.
flashing slowly.
– See "Settings menu,
Display / keypad
illumination".
The programme does No obvious cause.
– Is the dryer switched on?
not start.
– Is the plug correctly
inserted into the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
– If you cannot remedy the
problem, then there could
be a fault. Contact Miele
Service.
Power cut.
When power is restored, any programme which was
running will restart automatically.
The display is in a
A different language
Set the language you want.
different language.
has been selected.
The flag symbol J will guide
you.
– Switch the dryer off and
The interior drum
The lighting switches
lighting does not
off automatically (to
then on again.
come on.
save energy).
– If the lamp needs to be
replaced, follow the
instructions in "Changing
the lamp" at the end of this
section.
Access via a code has – When the code is entered
been activated.
the lighting will come back
on.
There are humming
noises.
The compressor is
operating.
51
Problem solving guide
Cleaning the cooling fins
(bottom right grille)
,In general, the cooling fins do
not need cleaning. They should only
be cleaned if the drying process is
taking an exceptionally long time
due to a very high level of dust or
fluff in the room in which the dryer is
installed.
,To prevent damaging the
cooling fins, only pass the vacuum
cleaner brush over them lightly,
without applying any pressure.
Use the yellow lever supplied to open
the bottom right grille.
^ Vacuum up any soiling carefully
using a vacuum cleaner dusting
brush or small crevice nozzle.
^ Insert the lever in the middle of the
gap at the top and lift it up gently
(see arrow) until the grille opens out
at the top.
^ Now remove the grille by pulling it
diagonally upwards.
^ Check whether the cooling fins are
clogged.
,Danger of injury.
Do not touch the cooling fins with
your hand. You could cut yourself.
52
^ To replace the grille, first insert the
bottom of the grille (as shown).
^ Then push the grille firmly into
position at the top.
Problem solving guide
Changing the lamp
Disconnect the tumble dryer from
the mains electricity supply.
^ Open the door.
You will find the interior light cover at
the top of the drum aperture.
The light specification and maximum
wattage is stated on the data plate
and on the light cover.
^ Turn the light anti-clockwise to
remove.
^ Replace the lamp.
^ To close the cover push it upwards
and press it on the left and right until
you hear it click into position.
,Ensure that it is fitted into
position securely, as any moisture
could cause a short circuit.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the light cover as illustrated.
^ Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele Dealer
or the Miele Spare Parts Department.
53
After Sales service
Repairs
Future updates (PC)
In the event of any faults which you
cannot remedy yourself, please contact
The indicator or check light marked PC
on the fascia panel is the interface used
by the Miele service technicians during
service work for testing purposes and
for updating the appliance's
programme data.
– your Miele dealer or
– the Miele Service Department (see
back cover for contact details).
When contacting your dealer or the
Service Department, please quote the
model and serial number of your
appliance, both of which are shown on
the data plate. This is visible when you
open the door.
Appliance guarantee
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. However you must activate
your cover by calling 0845 365 6640 or
registering online at www. miele.co.uk.
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
Optional accessories
Optional accessories for this dryer are
available from your Miele Dealer, the
Miele Spare Parts Department or via the
internet at www.miele-shop.com.
N.B. A call-out charge will be
applied for service visits where the
problem could have been resolved
as described in these instructions.
54
Please note that telephone calls may
be monitored and recorded for
training purposes.
Installation and connection
Front view
a Mains connection cable
f Four height adjustable screw feet
b Control panel
g Cool air intake grille (do not obstruct
with a laundry basket or other
objects)
c Condensed water container (empty
after every drying programme)
d Door
e Service panel for the fine filter (do
not open during drying)
h External drainage of condensed
water hose (see "External condensed
water outlet")
55
Installation and connection
Rear view
,If transporting the dryer at an
angle, only tip it towards its left side.
a Protruding lid for holding when
moving the dryer (see arrows)
b Mains connection cable
c Hose for external drainage of
condensed water
d Accessories for connection to a sink
drain outlet
Transporting the dryer
When moving the dryer, hold it by the
lid where it protrudes to the rear. To
manoeuvre the dryer out of its packing
case to its installation site you will also
need to hold it by the front feet.
,Only transport the dryer as
shown in the following illustrations.
,If the tumble dryer has not been
transported as described, then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply. Otherwise the
heat pump can be damaged.
56
Installation and connection
Installation site
,Make sure the dryer door can be
opened without hindrance after
installation.
,The cool air intake panel at the
front of the dryer must not be
blocked or covered, e.g. by a
laundry basket, as this would cause
a fault.
Building under a continuous worktop/
in a row of kitchen units
,It is very important to avoid a
build-up of heat.
The warm air which is expelled from
the rear of the dryer must be able to
dissipate.
Warm air which cannot dissipate
could cause a fault.
A build-up of heat can be avoided by:
– Adjusting the screw feet so that there
is a gap of at least 20 mm between
the floor and the bottom of the dryer.
– Creating a gap for the dryer in the
kitchen furniture plinth facing.
– Creating ventilation gaps in the
kitchen unit.
N.B. When built under, drying times
may be longer.
,The dryer should not be installed
next to a refrigeration appliance. The
warm air expelled from the rear of
the dryer would increase the
temperature around the refrigeration
appliance's heat exchanger causing
the compressor to run continuously.
If it is not possible to install the dryer
anywhere else, then the refrigeration
appliance must be sealed off from
the dryer.
,A building-under kit (Miele
accessory, available to order) with a
coverplate to replace the
appliance´s lid is required. It must
be fitted by a suitably qualified
person to ensure electrical safety.
N.B. If you wish to push the tumble
dryer under a worktop and there is
space to do this without removing
the lid the building-under kit is not
necessary. Otherwise the
building-under kit is essential.
– The building-under kit is supplied
with its own installation instructions.
– N.B. When built under, drying times
may be longer.
– The electrical socket must be
located in an accessible position
near the appliance.
With niche heights of:
– 830-840 mm, longer screw feet* are
required.
– 870-885 / 915-930 mm, one or two
raising kits* are required.
* Miele accessory available to order
57
Installation and connection
Levelling the appliance
Before moving the tumble dryer
again (e.g. when moving house)
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the tumble dryer is tipped up
when it is being moved. It is a good
idea to run the Cool air programme for
approximately 1 minute before moving
it. Any remaining condensed water will
then be fed into the condensed water
container or out through the drain hose.
The appliance must be perfectly level
to ensure safe and proper operation.
Washer-dryer stack
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. The
appropriate "WTV" stacking kit* to
match your dryer is required.
* Miele accessory available to order
,Stacking kits must only be
installed by a suitably qualified fitter.
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
,Do not block the gap between
the bottom of the tumble dryer and
the floor with plinth facings, deep
pile carpet etc. This would hinder a
sufficient flow of air to the dryer.
58
Installation and connection
External condensed water
outlet
General notes
^ There will be a small amount of
residual water in the drain hose.
Have a container ready to collect
this.
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose at
the back of the dryer. The condensed
water can also be drained off directly if
the tumble dryer is installed near a sink,
drain outlet etc. so that the condensed
water container does not have to be
emptied.
Drain hose length . . . . . . . . . . . . 1.50 m
Maximum delivery head . . . . . . . 1.50 m
Maximum drain hose length . . . . 4.00 m
,If the on-site water drainage
system is not fitted with a non-return
valve or an appropriate air gap, one
must be fitted to prevent the risk of
back-flow. (See "Installation conditions
requiring a non-return valve").
^ Pull the hose off its connection (see
arrow).
^ Allow any residual water to run into
the container.
^ Unwind the hose and pull it carefully
out of the holders.
The following optional accessories are
available:
– an extension hose
– a non-return valve kit for connection
to an external condensed water
outlet (includes an extension hose).
Maximum delivery head with
non-return valve fitted: 1.00 m
Arranging the drain hose
,Do not pull on the drain hose and
do not stretch it or allow it to become
kinked as it could get damaged.
^ Position the hose to the right or left
hand side as necessary.
Leave the hose in the middle holder to
prevent it from becoming kinked
inadvertently.
59
Installation and connection
External drainage via a sink or gully
^ See "Front view" illustration.
,If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Example: Connection to a sink drain
outlet
The drain hose with non-return valve
fitted can be connected directly to a
suitable sink drain outlet.
^ Use the bow-shaped guide to
prevent the drain hose from
becoming kinked.
Installation conditions requiring a
non-return valve
,Certain installation conditions
require the fitting of a non-return
valve for external water
connection (available as an
optional accessory). A non-return
valve will prevent the risk of
back-flow out of the dryer which
could cause damage.
A non-return valve is required:
– If the tumble dryer is connected to a
sink drain outlet (see the following
section).
– If the tumble dryer is connected to a
drainage system already in use by
another appliance, e.g. a dishwasher
or washing machine.
60
^ Remove the following from the back
of the dryer at the top:
Adapter 1 and hose clip 3 behind it.
Installation and connection
^ Fit adapter 1 to the sink drain outlet
using nut 2.
If this nut has a flat disc in it you
should take the disc out first.
^ Attach the end of hose 4 to adapter
1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
1 Adapter
2 Nut
3 Hose clip
4 End of the hose
5 Non-return valve
6 Tumble dryer drain hose
,Non-return valve 5 has to be
fitted with the arrow pointing in the
direction of flow (i.e. towards the
sink). Otherwise water will not drain
out of the appliance.
^ Fit non-return valve 5 to tumble dryer
drain hose 6 (make sure it is fitted in
the correct direction - see arrow on
non-return valve).
^ Secure the non-return valve using
hose clips.
61
Electrical connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
62
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING: THIS APPLIANCE
MUST BE EARTHED
Consumption data
Cottons Normal2
Cottons Normal
Cottons Normal
+ Gentle tumble
+ Freshen up
Cottons Hand iron rr
Load1
Final spin speed in a
domestic washing machine
Residual
moisture
kg
8.0
4.0
8.0
8.0
8.0
8.0
rpm
1000
1000
1200
1400
1600
1800
%
60
60
53
50
44
43
kWh
2.02
1.11
1.80
1.70
1.55
1.50
min.
154
89
139
132
118
116
8.0
3.0
8.0
8.0
8.0
8.0
8.0
3.5
1000
1000
1000
1200
1400
1600
1800
1200
60
60
60
53
50
44
43
40
2.05
0.95
1.40
1.20
1.15
0.95
0.95
0.60
153
75
111
97
91
77
75
51
Energy Duration
Minimum iron Normal
Minimum iron Normal
+ Gentle tumble
3.5
1200
40
0.60
53
+ Freshen up
3.5
1200
40
0.65
52
Minimum iron Hand iron
3.5
1200
40
0.50
45
Automatic plus Normal
5.0
800
50
1.35
109
Shirts Normal
2.0
600
60
0.70
57
+ Gentle tumble
2.0
600
60
0.75
60
Hygiene Normal
3.5
1000
60
1.70
140
Gentle smoothing
1.0
1000
60
0.30
30
Proofing Normal
2.0
800
50
1.20
99
Outerwear Normal
2.5
800
50
0.95
80
Denim Normal
3.0
900
60
1.30
107
+ Gentle tumble
3.0
900
60
1.40
115
Express Normal
3.5
1000
60
1.00
82
Woollens
2.0
1000
50
0.15
20
1
Weight of dry laundry
2
Test programme in accordance with Regulation 392/2012/EU for energy labelling measured in
accordance with EN 61121.
All data was calculated using EN 61121 unless otherwise stated.
Notes for test institutes:
– When selecting the Cottons programme, drain the condensed water away through the drainage
hose.
– Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual
moisture as per the above standard using the Cottons Normal programme without any extra
options.
Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any extra options selected.
63
Technical data
Height
850 mm
Width
595 mm
Depth
Depth with door open
596 mm
1071 mm
Height for building under
Width for building under
820 mm
600 mm
Depth for building under
Suitable for pushing under a
worktop
600 mm
yes
Suitable for stacking
Weight
yes
61 kg
Drum volume
Maximum capacity
111 litres
1-8 kg dry weight
Capacity of condensed water
container
Drain hose length
Approx. 4.2 litres
Maximum delivery head
Maximum drain hose length
1.5 m
4m
Length of connection cable
2m
1.5 m
Voltage
Connected load
Fuse rating
See data plate
Lamp wattage
Test certificates awarded
Energy consumption
64
see "Consumption data"
Settings menu
The Settings menu is used to alter the dryer's electronics to
suit different requirements.
Settings can be altered at any time.
Open the Settings menu
\
\
\
Main menu
10:21
$ Settings !
# Favourite programmes
# Cottons
[
m [
^ Use the top right hand sensor to select the Settings !
menu.
^ Confirm with OK.
To select a setting
\
\
\
Settings
10:21
$ Language !
# Time
! Drying levels
[
m [
^ The sensors on the right can be used to scroll up or down
the list.
Language J
The display can be set to appear in one of several different
languages.
To select the language you want, go to the Language J
sub-menu.
The flag after the word Language acts as a guide to prevent
a language which will not be understood from being set.
65
Settings menu
Time
The time can be set to appear as a 24 hour or 12 hour
clock. You can also use this setting to adjust the time of
day.
Clock format
\
\
Time
10:21
$ 24 h clock (
# 12 h clock
OK !
[
^ Select the format you want.
The dryer is delivered with the clock format set as a 24 hour
clock.
Set the time of day
Time
+ $
10 :21
- #
OK !
^ Use the + and - sensors to set the hour.
^ Confirm the hours with OK and then enter the minutes.
Drying levels
You can alter the drying levels for the Cottons, Minimum
iron and Automatic plus programmes.
The bars show you the setting.
The default is: the middle setting.
– Drier P P P P P P P
the programme duration increases.
– Damper P
the programme duration is shorter.
66
[
[
[
Settings menu
Code
The code prevents the dryer being used without your
knowledge.
When the code has been activated, you have to enter a code
after switching the dryer on. Otherwise the dryer cannot be
operated.
The door can be opened and items removed at any time.
To activate the code
The display will now request that a code is entered. The code
is 250 and cannot be altered.
Activate code
10:21
+ $
2
AA
Please enter code
– #
OK !
[
[
[
^ Use + to enter the first number.
^ Confirm the first number with OK and then enter the second
number. Repeat the process until all three numbers have
been entered.
^ After the last number has been entered, you must confirm
the code with OK.
Information
0
10:21
Input OK. Code active when machine is
switched off.
OK !
[
^ Confirm with OK.
^ Switch the dryer off.
67
Settings menu
To use the dryer when the lock code is activated
When the dryer is switched on again, the display will request
the code.
^ Enter code 250 with the + and - sensors.
The dryer is now unlocked and ready for use.
To deactivate the code
^ Proceed as for activating the code.
Information
1
Code OK. Ready
OK !
[
^ Confirm with OK.
You can now switch on the dryer without being asked to enter
a code.
68
Settings menu
Buzzer
When the buzzer function has been
activated, an audible tone sounds at
the end of a programme.
Off
Factory default
The buzzer is switched off but sounds
at maximum volume if there is a fault.
Normal
The buzzer sounds at the end of a
programme.
Loud
The buzzer sounds louder at the end of
a programme.
Keypad tone
An audible tone sounds each time a
button is pressed.
If you make an alteration it will appear
in the display immediately.
Display / keypad illumination
The display and sensor illumination
switches off to save energy.Start
flashes slowly to save energy.
The display and the sensors are not
illuminated.
– if a programme is not selected within
10 minutes of the tumble dryer being
switched on.
– 10 minutes after the end of a
programme.
Press the Start sensor to activate the
display and sensor illumination again.
Off after 10 minutes
The display and sensor illumination will
switch off 10 minutes after the
programme has started.
Off
"On" whilst programme is running
Factory default
Factory default
On
The display and sensors remain lit up
whilst the programme is running.
Brightness
Contrast
The display contrast and brightness
can be altered in stages.
The bars P P P P P P P show you
which level is set.
69
Settings menu
Memory
The electronics will memorise the
drying level and some of the extra
options selected for the current
drying programme and the duration
of a timed drying programme.
When the programme is chosen again
these settings will appear in the
display.
Off
Factory default
On
Anti-crease
Anti-crease helps prevent creasing, if
laundry is not normally removed immediately after the end of a
programme.
After the programme has finished, the
drum will continue to rotate at intervals.
There is no anti-crease phase with
Wollens.
Off
1 hour
2 hours
(Factory default)
70
Optional accessories
Optional accessories for this dryer are
available from your Miele Dealer or from
the Miele Spare Parts Department,
or via the internet at
www.miele-shop.com.
Fragrance flacon
For a pleasant fragrance when drying
your laundry.
Holder for fragrance flacon
The holder is required to fit the
fragrance flacon to the fluff filter.
The holder comes with its own
instructions.
Dryer basket
This enables items which must not be
subjected to mechanical action to be
dried or aired.
The dryer basket comes with its own
instructions.
71
Alteration rights reserved/0113
M.-Nr. 09 459 300 / 02