Siemens WM14Y890GB Instruction manual

w
WM14Y890GB
w
w
.d
ev
ic
em
an
ua
ls
.e
u
en Instruction Manual
and Installation
Instructions
Washing machine
www.siemens-home.com
Your new washing machine
You have chosen a premium washing machine made by
Siemens. Thanks to its innovative technologies, the washing
machine is distinguished by its perfect washing performance and
its economic consumption of water and energy.
Please take a couple of minutes to read and become familiar
with the advantages of your washing machine.
To meet the high quality demands of the Siemens brand, each
washing machine, which leaves our factory, is inspected
thoroughly to ensure that it functions properly and is in perfect
condition.
ua
ls
.e
u
Further information on our products, accessories, spare parts
and services can be found at: www.siemens-home.com or
contact our customer service centres.
em
an
If the instructions for use and assembly describe various models,
reference is made to the differences at the appropriate places.
ev
ã Warning!
ic
Explanation of the symbols
w
w
.d
This combination of symbol and signal word indicates a
potentially dangerous situation which may result in death or
serious injuries unless it is avoided.
w
ã Caution!
This combination of symbol and signal word indicates a
potentially dangerous situation which may result in slight or
minor injuries or damage to property and the environment.
²
Instructions on how best to use the appliance as well as other
useful information.
2
Contents
neIstrucMaioanstdionucIsalrInio stalla t
Before washing
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Intended use
Safety instructions
Protection of the environment
Getting to know your appliance
Detergent drawer
Operating elements/Display elements
The main points in brief
4
5
8
9
10
11
12
Operating the appliance
em
an
ua
ls
.e
u
Before each washing
Washing
After washing
Programme overview
Programme settings/options
Anti-stain system
Intelligent Dosing System
Consumption values
Appliance settings
Sensors – Your washing machine is so intelligent
ic
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
13
19
22
23
30
33
34
39
40
41
w
.d
Care and maintenance
Emergency lock release, e.g. if power failure occurs
Information on the display panel
Faults, what to do?
Customer service
w
w
Ø
Ø
Ø
Ø
Ø
ev
Cleaning
leaning and maintenance
42
48
49
50
52
Installing the appliance
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Index
Standard accessories
Installation
Remove transportation protection devices
Connecting the water
Alignment
Electrical connection
Before the 1st washing
Transportation, e.g. if moving house
53
55
59
61
65
66
68
69
70
3
Intended use
Beforwangeshi
Ø For use in the household only.
Ø The washing machine is suitable for washing machine-
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
washable textiles and hand-washable wool in wash liquor.
Ø The washing machine is suitable to be operated with cold
drinking water and commercially available detergents and
care products which are suitable for use in washing
machines.
Ø When dosing all detergents, cleaning aids, cleaning products
and cleaning agents, always follow the manufacturer's
instructions.
Ø The washing machine may be operated by children from 8
years of age, by persons who have limited physical, sensory
or mental abilities and by persons who have inadequate
experience or knowledge, provided they are supervised or
have been instructed by a responsible person.
Ø Keep pets away from the washing machine!
ead and follow the operating and installation instructions and all
Read
other information enclosed with the washing machine.
Retain documents for subsequent use.
4
Safety instructions
ã Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
– Never pull out the mains plug by tugging the power
cord.
– Insert/pull out the mains plug with dry hands only.
ã Warning!
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
Risk to children!
– Do not leave children unsupervised near the
washing machine.
– Children must not play with the washing machine.
– This will prevent children from locking themselves
in and suffocating.
On redundant appliances:
– Pull out the mains plug!
– Sever the power cord and discard together with
the plug.
– Destroy the lock on the washing-machine door.
– Children must not perform any cleaning or
maintenance work without supervision.
– When playing, children may become entangled in
the packaging/film and packaging parts or pull
them over their heads and suffocate.
Keep packaging, plastic film and packaging parts
out of the reach of children.
– When washing at high temperatures, the glass of
the washing machine door becomes hot.
5
Prevent children from touching the hot washing
machine door.
– Detergents and care products may cause
intoxication if consumed or eye and skin irritation if
touched.
Keep detergents and care products out of the reach
of children.
ã Warning!
em
an
ua
ls
.e
u
Risk of explosion!
Items of washing pretreated with solvent detergents,
e.g. stain remover/petroleum ether, may cause an
explosion when the washing machine has been
loaded.
Before hand thoroughly rinse items of washing by
hand.
ic
ã Caution!
w
w
w
.d
ev
Danger of scalding!
When washing at high temperatures, you may be
scalded if you touch the hot wash liquor (e.g.
if draining hot wash liquor into a washbasin or if
draining the washing machine in an emergency). Allow
detergent solution to cool down.
ã Caution!
Risk of damaging appliance!
– Cover plate may break!
Do not climb on the washing machine.
– Opened washing machine door may break off or
washing machine may overturn!
Do not lean on the open washing machine door.
6
ã Caution!
Danger when reaching into/gripping the rotating
drum!
If you reach into the rotating drum, you may injure your
hands.
Do not grip the rotating drum. Wait until the drum stops
rotating.
ã Caution!
ic
em
an
ua
ls
.e
u
Risk of coming into contact with liquid detergents/
care products!
If the detergent drawer is opened while the washing
machine is running, detergent/care product may spray
out.
Caution when opening the detergent drawer.
In case of eye/skin contact, rinse thoroughly.
If accidentally swallowed, seek medical advice.
ev
ã Caution!
w
w
w
.d
Hazard due to detergent/softener running out of the
dispensers!
Leaking detergent/softener may impair the function of
the appliance, e.g. damage to electronics.
Before transporting the appliance, always drain
dispensers.
7
Protection of the environment
Packaging/Old appliance
)
Dispose of packaging in an environmentally friendly manner.
This appliance has been identified in accordance with the
European Directive 2002/96/EG on Waste Electrical and
Electronic Equipment (WEEE).
The Directive specifies the framework for an EU-wide valid return
and recycling of waste appliances.
Hints and tips
u
Ø Utilise the maximum amount of washing for the partic
particular
programme.
an
ua
ls
.e
Ø Wash normally soiled washing without Pre-wash.
Ø Instead of Cotton 90 °C programme select Cotton 60 °C
and ecoPerfect ¦ button. Comparable cleaning result with
significantly lower energy consumption.
em
Ø Detergent dosage using the intelligent dosing system helps
w
w
w
.d
ev
ic
save detergent and water.
Ø Energy saving mode: The display panel light goes out after
several minutes, Start/Reload Ü flashes. To activate the
light, select any button.
The energy-saving mode is not activated if a programme is
running.
Ø Automatic switch off: If the appliance is not operated for a
prolonged period, it automatically switches off before the
programme starts and when the programme has ended to
save energy. Switch on by pressing main switch # button.
Ø If the washing is then dried in the tumble dryer, select spin
speed according to the instructions of the dryer
manufacturer.
8
Getting to know your appliance
2SHUDWLQJ
HOHPHQWV
'LVSOD\
HOHPHQWV
'HWHUJHQWGUDZHU
'UXPOLJKW
'RRU
em
an
ua
ls
.e
u
GHSHQGLQJ
RQPRGHO
w
w
w
.d
ev
ic
6HUYLFHIODS
2SHQLQJ
FODFN
DQGFORVLQJWKHGRRU
6HUYLFHIODS
9
an
ua
ls
L
.e
u
Detergent drawer
.d
ev
ic
em
Intelligent Dosing System (i-Dos):
Your washing machine features an intelligent dosing system for liquid detergent and
softener. Dispensers i-Dos ô (1.3 l) and i-Dos iIô (0.5 l) in the detergent drawer are
used
sed for this. You can select whether you want to use one liquid detergent and one
softener or two liquid detergents.
Depending on the selected programme and settings, the optimum amounts of detergent/
softener are dosed via the i-Dos containers.
w
w
w
At the factory the dosage has been preset for:
– i-Dos ô ¨ detergent for lightly soiled washing and
– i-Dos iIô © softener for normally soft washing.
Overview
verview of the i-Dos settings starting on ~ Page 23
0{
ð
¼ü½
10
ð
for intelligent dosage: liquid detergent
Dispenser ô
Dispenser i ô for intelligent dosage: softener or liquid detergent
Dispenser À Á for manual dosage. ~ Page 38
Operating elements/Display elements
M NO P
S
ua
ls
QR
.e
u
V
T
KU
i Indicator lights for intelligent dosage
m
n
o
p
em
ic
ev
.d
w
l
w
k
q Start
Start/Reload Ü button to start, interrupt
~ Page 35
and cancel the programme (e.g. reload
washing).
Button ecoPerfect ¦
h
Simultaneously hold down Basic
~ Page 17, ~ Page 30
Settings 3 sec. for appliance settings
Press the main switch # button. Switch
(end signal, button signal, language,
on
n and off the appliance.
autom. switch off, i-Dos settings) for
Programme selector – can be rotated in
approx. 3 seconds. Overview of all
either direction. Programme Overview,
settings ~ Page 40
refer to ~ Page 23
r
Display panel for settings and
Button speedPerfect
Perfect G
information.
~ Page 17, ~ Page 30
s Select × Options for additional
Buttons Temperature, Spin,
programme options.
Finish in-time ~ Page 17, ~ Page 30
Overview of all options ~ Page 32
i-Dos iIô button,
Dosage ~ Page 18, ~ Page 31
i-Dos ô button,
Dosage ~ Page 18, ~ Page 31
w
j
an
² All buttons are sensitive, they only need to be touc
touched gently.
11
The main points in brief
@
1
Insert mains plug.
Turn the tap on.
@
Open the washing
machine door.
@
@
To switch on, press
the # button.
Select the
programme, e.g.
Cotton.
Dosage: automatic
Please load laundry: max. 8kg
ú
Finished, remove washing
End of the programme
12
@
w
v
@
Select
Start/Reload Ü.
w
w
4
If required, change programme settings of the
selected programme and select programme
settings/options.
.d
Close the washing
machine door.
ev
ic
em
FODFN
@
Do not exceed maximum load.
ua
@
Insert the washing.
an
Sort the washing.
3
ls
.e
u
2
@
For switching the
machine on, press
the # button.
Turn off the mains
supply (for models
without Aqua-Stop).
Before each washing
atnighepOpcielr
²
– Install and connect washing machine properly.
Refer to ~ Page 55
– Before the 1st wash, wash once without any washing.
~ Page 68
1. Preparing the washing
ua
an
Coloureds 60 °C, 40 °C, 30 °C
em
Easy-Care 60 °C, 40 °C, 30 °C
ev
ic
Delicates 40 °C, 30 °C
.d
Hand and machine-washable silk and woollens cold, 40 °C,
30 °C
w
Do not wash laundry in the washing machine.
w
²
Cottons 95 °C, 90 °C
rotecting the washing and the machine:
Protecting
w
<;
:98
B A>
AL>
K
WAL
>K
Ž
ls
.e
u
Sorting the washing according to:
Ø Type of fabric/fibre.
Ø Colour.
Ø Soiling.
Ø Follow manufacturer’s care information.
Ø Care label specifications:
– When dosing all detergents, cleaning aids, cleaning products
and cleaning agents, always follow the manufacturer's
instructions.
– Keep detergents and agents for the pretreatment of washing
(e.g. stain remover, prewash sprays, ...) away from the
surfaces of the washing machine. Using a damp cloth,
immediately remove any fine spray residue and other
residue/droplets.
– Empty pockets.
– Remove metal parts (paper clips, etc.).
– Wash delicates in the net/bag (tights, underwired bras).
– Close zips, button up covers.
– Brush sand out of pockets and collars.
– Remove curtain fittings or include in the net/bag.
– Wash new items separately.
13
2. Preparing the appliance
Insert mains plug.
Turn on water tap.
3. Selecting a programme and puting the washing in the
drum
.e
u
1. Open the washing machine door.
ls
2. Check whether the drum has been completely emptied. If
em
an
ua
required, empty. Otherwise, the load display may malfunction.
~ Page 41
ic
3. Press the # button. The appliance is switched on.
w
w
.d
ev
The Siemens logo is indicated on the display panel and all
programme indicator lamps are lit.
w
Then always the Cotton programme preset at the factory is
displayed.
Displays for the Cotton programme:
c
c
c
60°C
1400B
2:31h
b
b
b
c
– The indicator lamp is lit on the programme selector and
the main menu for the selected programme is indicated
on the display panel.
– For appliances with drum light:
14
After switching on the appliance, after opening and
closing the washing machine door as well as after starting
the programme, the drum is lit. The light goes out
automatically.
4. Select a programme.
You can use the saved programme
or select another programme, Programme Overview, refer to
~ Page 23,
or select other programmes (see Others programmes) and
choose one programme as follows:
other programmes selected using Others and choose e.g.
Outdoor:
800 B
1:04h
Down
own
Outdoor
Rinse
è
c
b
ls
.e
Additional programms
u
30 °C
ua
Main menu
c
800B
1:04h
b
b
ev
.d
30°C
c
ic
c
em
an
– Select programme using the buttons under the arrows.
The selection is acknowledged by a tick.
– Wait or back by pressing Main menu button, selected
programme is indicated on the display panel.
Outdoor
b
w
b
c
w
w
– To change the programme, select button under the black
highlighted programme and change programme.
5. Insert the washing.
Dosage: 30%
Please load laundry: max. 8kg
ú
The load screen for the selected programme (e.g. for Cottons) is
indicated on the display panel. The load screen is indicated when
the door is opened or when the amount of washing is changed.
15
²
– Unfold and load presorted items of washing. Mix large and
small items. Washing items of different size distribute
themselves better during the spin cycle. Individual items of
washing may cause an unbalanced load. ~ Page 41
– Do not load washing until the main menu for the saved
programme is displayed after the Siemens logo.
– The load screen is indicated when the door is opened or
when the amount of washing is changed.
– The load bar progresses as the washing machine is loaded. If
the max. load is exceeded, the bar flashes. Do not exceed
indicated max. load. Overfilling reduces the washing result
and encourages creasing.
em
an
ua
ls
.e
u
²
– Unfold and load presorted items of washing. Mix large and
small items. Washing items of different size distribute
themselves better during the spin cycle. Individual items of
washing may cause imbalances.
– Do not load washing until the main menu for the saved
programme is displayed after the Siemens logo.
– The load bar progresses as the washing machine is loaded. If
the max. load is exceeded, the bar flashes. Do not exceed
indicated max. load. Overfilling reduces the washing result
and encourages creasing.
ev
w
c
w
FODFN
Take care not to trap any items of clothing between the loading
door and rubber seal.
Close the door.
.d
²
ic
4. Changing the settings of the selected programme
c
c
c
i-Dos iIô ©
i-Dos ø øô ¨
1400B
2:31h
b
b
b
w
60°C
The main menu for the selected programme is indicated again on
the display panel.
You can use the displayed presettings or adjust the selected
programme optimally to the items of washing by changing the
presettings or selecting additional settings/options.
16
Ø Change Temperature, Spin, Finish in time:
Selecting and changing e.g. the Temperature:
c
c
c
70
60°C
50
1400B
2:31h
i-Dos iIô ©
i-Dos øø ô ¨
b
b
b
The arrows on the display panel indicate which buttons are
used to change the settings. The settings are active without
acknowledgement and are displayed in the main menu.
ic
em
an
ua
ls
.e
u
– If the buttons are held down, the set values automatically run
through.
– The respective programme duration is displayed by selecting
the programme. The programme duration is adjusted while
the programme is running if the programme duration requires
changing, e.g. due to changes in the programme settings/
options, foam detection, unbalanced load detection, the load
or soiling.
Ø ecoPerfect ¦:
For saving energy with a comparable washing effect to the
standard programme. When selected, the display lamp is lit.
ev
Ø speedPerfect
erfect G :
w
w
.d
For a shorter wash time with a comparable washing effect to
the standard programme. Observe maximum load. Refer to
When selected, the display lamp is lit.
w
²
c
Ø ß Options. Overview of all options ~ Page 32
Select ß Options and e.g. z Water Plus button:
60°C
Extra rinse
zWater Plus
Rinse Hold
b
1400B
c
2:31h
z
on
è
b
c
– Select option by pressing the two buttons displayed on the
left.
17
– Select/deselect option by pressing the two buttons
displayed on the right. The selected options are
immediately active.
In the case of multi-level settings keep touching the
buttons to run through the settings automatically.
– Wait or back to the main menu by pressing ß Options
button.
Ø i-Dos iIô for dosing a softener or a second liquid
detergent:
Selecting i-Dos iIô and changing dosage strength:
1400 B
60°C
c
b
c
.e
b
iIô ª
u
i-Dos iIô dosage
2:31h
normal
ª strong
off
è
em
an
ua
ls
strong: for especially soft washing (softener) or for heavily
soiled or stained washing (detergent) when container
content: Detergent set
Ø i-Dos ô for dosing a liquid detergent:
Selecting i-Dos ô and changing dosage strength:
1400 B
ic
60°C
b
c
w
Do not manually dose additional detergent into detergent
drawer À Á, if intelligent dosage for detergent has been
activated; prevents overdosage and foaming.
6. Starting the programme
Ø Select Start/Reload Ü. The indicator light is on.
18
è
normal: for normally soiled washing.
w
²
c
ô©
w
.d
b
ev
i-Dos ô dosage
2:31h
light
© normal
strong
Washing
During the wash cycle the programme progress is indicated by a
bar on the display panel. The bar progresses in the course of the
wash cycle and provides information about the current
programme progress.
The arrows are switched on and off according to the programme
progress. They indicate the programme settings/options which
can be changed/added as the programme progresses.
c
1400B
b
c
i-Dos iIô ©
i-Dos ø øô ¨
an
b
2:31
2
:31h
ua
60°C
Load adjust active
ls
c
.e
Ø Load adjust active ~ Page 41
u
Some programme sequence steps explained:
em
Ø Prewash, wash, rinse, spin, drain ... are displayed during the
wash cycle.
w
.d
ev
ic
Ø Rinsing with aqua sensor ~ Page 41
Ø Extra rinse: foam
Ø Other displays ~ Page 49
During washing
w
w
Ø Childlock
o prevent the set functions of the washing machine from
To
being accidentally changed, the childproof lock can be
activated.
Activate/deactivate: press Finish in for approx. 5 seconds.
w Childlock has been activated
Display panel goes back to the Main menu after approx.
3 seconds.
19
If the programme selector is adjusted or a button is selected
while the childproof lock is active, the w symbol flashes
briefly.
Ø Topping up washing
When the programme has started, washing can be reloaded
or taken out as required.
Select Start/Reload Ü.
c
60°C
Pause:
c
1400B
i-Dos iIô ©
i-Dos ø øô ¨
2:31h
Reload is possible
b
b
– If there is a high water level, high temperature or if the drum
is rotating, the washing machine door remains locked for
reasons of safety and reload is not possible. Follow the
information on the display panel. To continue the programme,
select the Start/Reload Ü button. The washing machine
door is locked and the programme continues automatically.
– Load display is not active during relosding.
– Do not leave washing machine door open for a prolonged
period – water could run out of the washing.
Ø Changing the programme
iff you have mistakenly started a wrong programme:
ic
em
an
ua
ls
.e
u
²
c
w
w
w
.d
ev
1. Select Start/Reload
Start/Reload Ü.
2. Select another programme.
3. Select Start/Reload
Start
Ü . The new programme starts from
the beginning.
Ø Cancelling the programme
For
For programmes at high temperature:
Start/Reload Ü.
1. Select Start/
2. Cool down washing: select Rinse/Freshen Up
(see Others programmes).
3. Select Start/Reload Ü .
For programmes at low temperature:
1. Select Start/Reload Ü.
2. Select Spin * or Drain *.
(* see Others programmes)
3. Select Start/Reload Ü.
20
Ø End of programme by Rinse Hold
Rinse hold reached:
Select "spin" or "drain"
and then "start".
Spin
Drain
b
b
1. Select Spin (If required, adjust the spin speed) or Drain.
2. Select Start/Reload Ü.
End of the programme
u
Finished, remove washing is indicated on the display panel.
v
ua
ls
.e
Finished, remove washing
w
w
.d
ev
ic
Dose less detergent in the next wash cycle with the same load.
Reduce basic dosage. ~ Page 36
w
²
em
an
If Foam has been detected is also indicated on the display panel,
the washing machine has detected too much foam during the
wash programme and therefore automatically activates additional
rinse cycles to eliminate the foam.
21
After washing
1. Open washing machine door and remove washing..
ú
#
– Do not leave any items of washing in the drum. In the next
wash they may shrink or discolour something else.
– Remove any foreign objects from the drum and the rubber
seal – risk of rust.
– Leave detergent drawer and door open so that residual water
can evaporate.
an
Before switching the machine off:
em
– Always remove the washing. Otherwise, the load display may
malfunction.
– Always wait until the programme ends, as the appliance
could still be locked. Then switch the appliance on and wait
for the unlocking device.
2. Press the # button. Appliance is switched off.
w
w
w
.d
ev
ic
²
ua
ls
.e
u
²
Remove the washing.
Switch off the device.
3. Turn off the water tap.
Not required for Aqua-Stop models. ~ Page 72
22
Programme overview
The presettings of the
programmes are highlighted in
bold.
Options/Information
Name of the programme
Brief explanation of the programme and
for which textiles it is suitable.
max. load
selectable temperature as °C
selectable spin speeds in rpm, the
max. spin speed depends on the
model
u
possible programme options
ua
ls
.e
for the Less Ironing programme
option possible spin speeds
in rpm
possible automatic dosage of a
softener and a detergent
Ý can be selected/deselected
‒ cannot be selected
an
em
ic
Cotton
Hard-wearing textiles, heat-resistant
textiles made of cotton or linen.
ev
² .* reduced load for speedPerfect
speed
G
w
w
.d
option
Easy-Care
Textiles
extiles made of synthetic materials or
blended fabrics.
w
Õ
Programme/Type of washing
max. 8 kg/5 kg *
cold – 60 – 90 °C
0 ... 1400 ... 1600 rpm
¦,G,ã,!,æ,l,z ,$,ç
at æ: 0 ... 800 rpm
detergent Ý, softener Ý
max. 3.5 kg
cold – 40 – 60 °C
0 ... 1200 rpm
¦,G,ã,!,æ,l,z ,$,ç
at æ: 0 ... 600 ...800 rpm
detergent Ý, softener Ý
Mixed Fabrics
Mixed load consisting of textiles made of
cotton and synthetics.
max. 3.5 kg
cold – 40 °C
0 ... 1400 ... 1600 rpm
¦,G,ã,!,æ,l,z ,$,ç
at æ: 0 ... 600 ... 800 rpm
detergent Ý, softener Ý
23
The presettings of the
programmes are highlighted in
bold.
Programme/Type of washing
Options/Information
Delicates/Silk
For delicate, washable textiles, e.g. made
of silk, satin, synthetic fibres or blended
fabrics (e.g. silk blouses, silk scarf).
max. 2 kg
cold – 30 – 40 °C
0 ... 600 ... 800 rpm
².For machine wash use detergent
¦,G,ã ,!,æ,l ,z,$,ç
at æ: 0 ... 600 rpm
suitable for delicates and/or silk.
detergent Ý, softener Ý
W Wool
max. 2 kg
Hand or machine-washable wool or richwool textiles.
Especially gentle wash programme to
prevent shrinkage, longer programme
pauses (textiles rest in wash liquor).
u
0 ... 800 rpm
.e
$,ç
ls
detergent ‒, softener Ý
ua
².Wool is of animal origin, e.g.: angora,
cold – 30 – 40 °C
².For
or machine wash use detergent
suitable for wool.
em
an
alpaca, lama, sheep.
w
w
.d
ev
ic
Dark Wash
Dark
ark textiles made of cotton and dark
easy-care textiles.
Wash textiles inside out.
w
Rapi 15’
Extra
xtra short programme approx.
15 minutes, suitable for lightly soiled
washing as a small amounts of laundry.
max. 3.5 kg
cold – 30 – 40 °C
0 ... 800 ... 1200 rpm
¦,G,ã ,!,æ,l ,z,$,ç
at æ: 0 ... 600 ... 800 rpm
detergent Ý, softener Ý
max. 2 kg
cold – 30 – 40 °C
0 ... 800 ... 1200 rpm
$,ç
detergent Ý, softener Ý
Textile Guard
Washing followed by water proofing
of weatherproof and outdoor clothing
with membrane coating and waterresistant textiles. ~ Page 28
max. 1 kg
cold – 30 – 40 °C
0 ... 800 rpm
¦,G,ã ,l,z,ç
detergent ?, softener ‒
24
The presettings of the
programmes are highlighted in
bold.
Programme/Type of washing
Options/Information
Shirts/Blouses
Shirts/Blouses made of cotton, linen,
synthetics fibres or blended fabrics.
For non-iron shirts the shirts/blouses are
given only a short spin using the æ Less
Ironing option, hang up dripping wet.
~ Self-smoothing effect.
max. 2 kg
² .Wash shirts/blouses made of
delicates/silk in Delicates/Silk
programme.
cold – 40 – 60 °C
0 ... 800 rpm
¦,G,ã,!,æ,l,z ,$,ç
at æ: 0 ... 400 rpm
detergent Ý, softener Ý
u
max. 1 kg
cold – 30 – 40 °C
.e
Lingerie
For delicate, washable underwear e.g.
made of velvet, lace, Lycra, silk or satin.
ls
0 ... 600 rpm
ua
¦,G,ã,æ,l ,z,$,ç
an
at æ: 0 ... 400 rpm
detergent ‒, softener Ý
em
Curtains
3.5
.5 kg heavy curtains or 25 – 30 m² light
curtains.
cold – 30 – 40 °C
0 ... 400 ... 800 rpm
¦,G,ã,!,l,z ,$,ç
detergent Ý, softener Ý
w
.d
ev
ic
re-wash option has been preset.
² .Pre-wash
² .Reduced
educed rinse and final spin cycle.
² .For
or machine wash use detergent
max. 3.5 kg
w
suitable for curtains.
3
w
2
Auto
Hard-wearing
ard-wearing textiles.
The degree of soiling and the type of
washing are automatically detected and
the washing sequence as well as
intelligent dosage are optimally adjusted.
Auto Soft
Gentler treatment of washing. The degree
of soiling and the type of washing are
automatically detected and the washing
sequence as well as intelligent dosage
are optimally adjusted.
max. 6 kg
automatic, up to 40 °C
automatic, up to 1400 rpm
ã,$,ç
detergent Ý, softener Ý
max. 3.5 kg
automatic, up to 30 °C
automatic, up to 1000 rpm
ã,$,ç
detergent Ý, softener Ý
25
see ... Others
The presettings of the
programmes are highlighted in
bold.
Programme/Type of washing
Options/Information
Down Wear
Machine-washable textiles filled with
down, pillows, blankets.
max. 2 kg
cold – 40 – 60 °C
² Wash large items individually. Use
0 ... 1200 rpm
¦,G,ã,l,z,$
mild detergent. Measure detergent sparingly.
detergent ‒, softener ‒
max. 2 kg
Outdoor
Weatherproof and outdoor clothing with a
membrane coating and water-resistant
textiles.
u
0 ... 800 rpm
.e
¦,G,ã,æ,l,z,$,ç
ls
at æ: 0 ... 600 rpm
detergent ‒, softener ‒
ua
² Use special detergents suitable for
machine wash. Pour detergent into
dispenser À Á according to manufacturer’s specifications.
cold - 30 – 40 °C
an
² The laundry must not be treated with
fabric softener.
ev
ic
em
² Before washing, remove all fabric
softener
oftener residue from detergent drawer
(all dispensers).
w
w
w
.d
Rinse
Extra rinse with spin.
0 ... 1200 ... 1600 rpm
æ,l,z,$,ç
at æ: 0 ... 800 rpm
detergent ‒, softener Ý
Spin
Extra spin with selectable spin speed.
0 ... 1200 ... 1600 rpm
æ,ç
at æ: 0 ... 800 rpm
detergent ‒, softener ‒
26
see ... Others
The presettings of the
programmes are highlighted in
bold.
Programme/Type of washing
Options/Information
Spin/Low program
Extra spin cycle at reduced speed and
with especially gentle spin mechanism.
0 ... 800 ... 1200 rpm
æ,ç
at æ: 0 ... 600 rpm
detergent ‒, softener ‒
-
ls
-
u
-
.e
Drain
The rinsing water when Rinse Hold $
(without final spin) is activated.
w
w
w
.d
ev
ic
em
an
ua
detergent ‒, softener ‒
27
Automatic programmes
The degree of soiling and the type of washing are automatically
detected and the washing sequence as well as intelligent dosage
are optimally adjusted.
Ø Automatic: for durable textiles
Ø Automatic Soft: gentler treatment of washing
Textile Guard
²
– The laundry must not be treated with fabric softener.
– Use special detergents suitable for machine wash. Dosage
according to manufacturer’s instructions.
1. Set programme selector to Textile Guard.
2. Dose special detergent for outdoor textiles in
u
dispenser À Á .
.e
3. Select Start/Reload Ü. Programme stops before last rinse
ua
ls
cycle.
ic
em
an
Rinse hold reached:
Please
lease add to detergent drawer À
the
he water proofing agent
and then select "start"
ev
4. Dose textile-guard agent (max. 170 ml) in dispenser À Á.
.d
5. Select Start/Reload
Start/Reload Ü. After-treatment of the washing
w
²
w
Starching
w
according to manufacturer’s instructions.
The washing should not be treated with fabric softener.
Select Rinsing programme.
Manually dose liquid starch into dispenser À Á (if required,
clean beforehand) according to manufacturer’s instructions.
Select Start/Reload Ü .
Dyeing/Discolouring
Dye in household quantities only. Salt may attack stainless steel!
Observe specifications of the dye manufacturer! Do not discolour
washing in the washing machine!
28
Soaking
1. Dose detergent with i-Dos or pour into dispenser À Á
according to manufacturer’s instructions.
2. Set programme selector to Cotton 30 °C and select
Start/Reload Ü .
3. After approx. 10 minutes select Start/Reload Ü to stop the
programme.
4. After the required soaking time reselect Start/Reload Ü ,
w
w
.d
ev
ic
em
an
ua
ls
.e
u
Insert washing of the same colour. No additional detergent
required, the soaking solution is used for washing.
w
²
if the programme is to be continued or change the
programme.
29
Programme settings/options
Notes
ls
Buttons
.e
u
Depending on the programme, you can use the programme
options to adjust the washing process even more efficiently to
your items of washing.
Programme settings/options:
Ø Are active without acknowledgement.
Ø Can be selected or deselected or changed depending on the
programme progress.
Ø Settings i-Dos iIô and i-Dos ô are retained after appliance
is switched off. All other programme settings/options must be
reset for reselection.
efore and during the programme the presettings
Before
can be changed for as long as the arrows are displayed.
Maximum spin speed depends on the programme
and model.
an
ua
Temperature
em
Spin
Delays the Finished in time (end of programme).
Before the programme starts, the end of the programme can be preselected in h steps up to
maximum 24h.
When the programme has started, the preselected
time is displayed e.g. for 8h and counts down until
the wash programme starts. Then the programme duration is displayed, e.g. 2:30h.
When the programme has started, the preselected
time can be changed as follows:
1. Select Start/Reload Ü.
2. Select Finish in button and change Finish in time.
3. Select Start/Reload Ü .
w
w
w
.d
ev
ic
Finish in
To activate/deactivate the Childlock.
30
ecoPerfect ¦
For saving energy.
speedPerfectG
For a shorter wash time.
Buttons
Notes
To change the softener dosage strength (or detergent when container content: detergent set) for the
selected programme permanently until the next
change:
– light: slightly soft washing
– normal: normally soft washing
– strong: especially soft washing
i-Dos ô
light – normal –
strong – off
To change the detergent dosage strength for the selected programme permanently until the next change:
– light: lightly soiled washing
– normal: normally soiled washing
– strong: heavily soiled or stained washing
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
i-Dos iIô
light – normal –
strong – off
31
Press ß Options button to select: Notes
Pre-wash
on – off
For heavily soiled washing.
For intelligent dosage: Selected detergent is used
for prewash and main wash. To prevent overdosage,
select medium i-Dos setting.
For manual dosage: Divide detergent for pre-wash
and main wash. Put detergent for prewash in the
drum and pour detergent for main wash in
dispenser À Á .
Less Ironing
on – off
Reduces creasing by special spin sequence followed
by fluffing and reduced spin speed.
Extra rinse
ö + 1 Rinse
÷ + 2 Rinses
ø + 3 Rinses
Additional
dditional rinse cycles depending on the programme, prolonged programme duration.
² Residual moisture of the washing slightly increased.
ls
.e
u
² Recommended application: for particularly sensitive
ive skin or/and in areas with very soft water.
Increased water level, more gentle treatment of the
washing.
Rinse Hold
on – off
The washing remains in the water after the last rinse
cycle. End the programme.
32
an
em
ic
Reduced noise values by adjusted spin sequence
and deactivated end signal. Especially suitable for
washing at night.
ev
Stains
Selectable treatment of stains, see
~ Page 33
w
ß
w
w
.d
Silent Wash
on – off
ua
Water Plus
on – off
² Residual moisture of the washing slightly increased.
For washing stained laundry.
Anti-stain system
General information about stains
The Stains additional programme option for treating special
stains can be found via the Ö Options button.
A total of 16 different stains can be selected. The washing
machine adjusts the washing temperature, drum movement and
soaking time specific to the type of stain. Hot or cold water, gentle
or intensive washing control and long or short soaking provide
the wash programme with a special sequence for each type of
stain. The result: stains are treated optimally.
ua
em
í egg
Blood is first “dissolved” in cold water, then the selected wash
programme starts.
Egg particles are removed by soaking in the lukewarm water
bath, selecting a wash cycle with a high water level and running
additional rinse cycles.
an
ë blood
ls
.e
u
The treatment of two stains explained in the following
example
.d
ev
ic
For the other stains we have developed comparable solutions in
intensive studies.
w
á soil + sand
ì grass
ä coffee
î cosmetics
w
å baby food
ë blood
í egg
ò strawberry
w
Selectable treatment of stains
ó orange
â red wine
ê chocolate
à sweat
ï dirty socks
ð grease + oil
ñ tea
é tomatoes
33
Intelligent Dosing System
Your washing machine features an intelligent dosing system for
liquid detergent and softener. Dispensers i-Dos ô (1.3 l) and iDos iIô (0.5 l) in the detergent drawer are used for this. You
can select whether you want to use one liquid detergent and one
softener or two liquid detergents.
Depending on the selected programme and settings, the
optimum amounts of detergent/softener are dosed via the i-Dos
containers.
u
Switching on the appliance
w
.d
ev
ic
em
an
ua
ls
.e
The appliance has been preset at the factory for the dosing of a
liquid detergent and a softener, indicated by corresponding
changeable inserts in the fill covers:
Ø Þ Color detergent, pre-installed.
Ø i Softener only i-Dos MIô , pre-installed,
Ø ß Standard/universal detergent, enclosed.
If required, attach the enclosed programme selector label:
w
Filling dispenser
w
1. Open detergent drawer.
2. Open fill cover.
3. Pour detergent/softener. Fill dispenser maximum up to max
marking.
4. Close fill cover.
5. Slowly push in detergent drawer all the way.
When the appliance is switched on, the completely inserted
drawer is indicated by:
Ø Associated display is lit when intelligent dosage i-Dos ô /iDos i ô is selected. ~ Page 35
Ø Display flashes once and goes out, if intelligent dosage is not
selected. ~ Page 35
34
²
ua
Ø Illuminated displays on the drawer handle
an
In daily use
ls
.e
u
When selecting your detergent and care product, follow the
instructions of the manufacturers. We recommend the use of
standard, universal and color liquid and gel-like detergents for all
machine-washable, coloured textiles made of cotton and
synthetic materials.
Ø Use only self-flowing liquid products and gels which the
manufacturer recommends adding to a detergent drawer.
Ø Do not mix different liquid detergents. If changing the liquid
detergent (type, manufacturer, ...), empty the dispenser
completely. ~ Page 43
Ø Do not use any solvent-based, corrosive or gas-emitting
products (e.g. liquid beach).
Ø Do not mix detergent and softener.
Ø Do not use any superimposed or highly thickened products.
Ø To prevent product from drying, do not leave the fil
fill cover
open for a long time.
w
w
w
.d
ev
ic
em
– Display is lit if intelligent dosage is selected for the
dispenser. In the case of the combined container i ô
the indicator light is lit for the stored container content
(i for softener/ô for detergent). ~ Page 40
– Display flashes if the fill level for the container is below
the minimum when intelligent dosage has been selected.
– Display flashes briefly when drawer has been inserted
correctly.
Ø Selecting and deselecting intelligent dosage/adjusti
dosage/adjusting
dosage strength
The intelligent dosage of detergent and softener is selected
in the factory for all permitted programmes. Refer to The
dosage strength for detergent has been preset to light (lightly
soiled washing) and for softener to medium (normally soft
washing) and can be individually changed for each
programme. Refer to ~ Page 18
In addition to intelligent dosage, washing additives (e.g. stain
remover) can be added manually via dispenser À Á .
~ Page 38
²
The selection (on/off) of i-Dos MIô and i-Dos ô is retained for
each programme until the next change occurs, even if the
machine is switched off.
35
Ø Reloading detergent/softener
The flashing of the associated illuminated display when
intelligent dosage is selected and a corresponding message
on the display panel indicate that the level is below the
minimum. There are still enough contents for approx.
3 washes.
The same detergent or softener can be topped up at any
time. If the product/manufacturer is changed, we recommend
cleaning the dispensers beforehand. ~ Page 43 If required,
adjusting the basic dosage. ~ Page 36
Standard settings
Ø If required, change basic dosages for detergent and softener:
w
w
.d
ev
ic
em
an
ua
ls
.e
u
The basic dosage amount to be set corresponds:
For detergents – to the manufacturer’s recommendation for
normal soiling and to the particular water hardness.
For softeners – to the manufacturer’s recommendation for
medium softness and to the particular water hardness.
This information can be found on the package label of the
detergent/softener or ask the manufacturer directly.
To determine the existing water hardness, use a test strip or
check with your water utility company.
My water hardness:
w
Here is an example of the detergent dosage on a package
label:
Degree of soiling ヾ
Water hardness ゝ
²
36
light
normal
heavy
very
heavy
soft/medium
55 ml
75 ml
120 ml
160 ml
hard/very hard
75 ml
95 ml
150 ml
180 ml
– Factory setting of the basic dosage: for detergent 75 ml and
for softener 36 ml.
– In the case of more concentrated detergents reduce the
basic dosage amount.
Ø If intensive foaming occurs repeatedly during washing, please
w
w
.d
ev
ic
em
an
ua
ls
.e
u
– An additional changeable insert for a second detergent is
enclosed and can be fitted in the fill cover.
– When the i-Dos i Iô container content is switched from
softener to detergent,, the basic dosage amount of detergent
for this container is set to the factory setting (75 ml) and the
dosage for this detergent is set to off in all permitted
programmes. Then select the detergent dosage (light, normal
or strong) via the i-Dos iIô button on the display panel.
~ Page 18
The i-Dos ô container is automatically deactivated if the
detergent dosage is activated for the i-Dos iIô container.
The settings are retained for this programme until the next
change.
– When the i-Dos i Iô container content is switched to
softener,, the basic dosage amount is set to factory setting
(36 ml) and the dosage is set to normal in all permitted
programmes.
– Switching over the container contents requires an additional
acknowledgement via the display panel.
w
²
check the basic dosage setting and dosage strength.
Furthermore, some liquid detergents may have a tendency to
excessive foaming. If the basic dosage settings and dosage
strengths are correct, it is recommended to use a different
liquid detergent.
Change basic dosage amount. ~ Page 40
Ø If required, convert i-Dos iIô dispenser contents.
Instead of softener, a second liquid detergent can also be
used in dispenser i-Dos iIô.
Change dispenser content. ~ Page 40
i
Cancel
A change to the i-Dos content
resets the i-Dos iIô settings
to their standard value.
Continue
37
Manual dosage
In the case of programmes in which intelligent dosage is not
possible or not requested (then set intelligent dosage to off),
detergent is added to detergent drawer À Á .
In addition to intelligent dosage of detergents - cleaning agents
such as water softener, bleach or stain remover can also be
dosed here.
1. Pull out the detergent drawer.
2. Dosing in dispenser À Á according to:
– Dosage recommendation on the display panel, e.g. for
Cottons:
ú
ua
ls
.e
u
Dosage: 70%
Please load laundry: max. 8kg
ev
.d
– When dosing all detergents, cleaning aids and cleaning
agents, always follow the manufacturer's instructions.
– Dilute viscous fabric softener and fabric conditioner with
water. Prevents blockage of the overflow!
– If detergent is dosed manually, no additional detergent via
intelligent dosage (set intelligent dosage to off). It prevents
overdosage and foaming.
w
w
w
²
ic
em
an
Depending on the amount of washing in the washing
machine, a dosing recommendation is indicated on the
display panel.
– Soiling.
(~ Page 36) or ask your water supply
– Water hardness (~
company.
– Manufacturer’s instructions.
38
Consumption values
Load
Energy
consumption ***
Water ***
Programme
duration ***
Cotton 30 °C *
8 kg
0.38 kWh
57 l
2:21 h
Cotton 40 °C *
8 kg
0.97 kWh
57 l
2:31 h
Cotton 60 °C *
8 kg
1.31 kWh
57 l
2:31 h
Cotton 90 °C
8 kg
2.40 kWh
68 l
2:21 h
Easy-Care 40 °C *
3.5 kg
0.55 kWh
41 l
1:35 h
Mixed Fabrics 40 °C
3.5 kg
0.58 kWh
37 l
0:53 h
Delicates/Silk 30 °C
2 kg
0.14 kWh
34 l
0:43 h
Wool 30 °C
2 kg
0.19 kWh
u
Programme
0:40 h
.e
39 l
ls
Programme setting for tests according to currently valid European standard EN60456.
Information about comparability tests: To test the test programmes, wash indicated load
size at maximum spin speed.
an
ua
*
Additonal
function
Load
Cotton 40/60 °C
ecoPerfect **
em
Programme
8/4 kg
Annual energy Annual water
consumption consumption
189 kWh
10500 l
w
w
w
.d
ev
ic
*** Programme setting for testing and energy labelling according to directive 2010/30/EU
with cold water (15 °C).
*** The values may deviate from the stated values depending on water pressure and hardness, room temperature, type and amount of laundry, detergents used, fluctuations in
the mains voltage and selected additional functions.
39
Appliance settings
By pressing the Basic Settings 3 sec. buttons, appliance settings
can be changed, e.g. button signal.
Simultaneously hold down Basic Settings 3 sec. buttons for
approx. 3 seconds:
Language
end signal
button signal
b
c
off
è
b
c
u
Ø If the buttons are held down, the settings automatical
automatically run
Settings are retained after appliance is switched off.
em
²
an
ua
ls
.e
through.
Ø Select Setting with the two left buttons.
Ø Select displayed value with the two right buttons (s
(selection
acknowledged by a tick).
asic Settings 3 sec. buttons again.
Ø Wait or hold down Basic
Set values
end signal
ff – quiet – medium –
off
loud – very loud
Notes
Adjust volume of the end signal.
button signal
off – quiet – medium –
loud – very loud
Adjust volume of the button signals.
Auto
power-off of
the appliance
in 15 – 30 – 60 min –
never
The appliance automatically switches off after ...
min. (= 0 kWh energy consumption); to switch
on, press main switch button # .
w
w
w
.d
ev
ic
Settings
language
German
GB English
...
Change displayed language.
i-Dos i ô
content
Softener –
Detergent
Select dispenser contents.
i-Dos i ô
10 ml – 200 ml
i-Dos ô
10 ml – 200 ml
Set basic dosage according to
recommendation of the detergent/softener
manufacturer.
40
Sensors – Your washing machine is so
intelligent
Load adjust
Depending on the type of textile and load, the load adjust
optimally adjusts the water consumption in each programme.
Aqua-Sensor
ua
ls
.e
u
During the wash and rinse cycles the Aqua sensor checks the
degree of turbidity (turbidity is caused by dirt and detergent
residue) of the washing and rinsing water. The duration and
number of rinse cycles are specified depending on the water
turbidity and, if required, an additional amount of detergent is
dosed in the automatic programmes.
an
Load sensor/Load display
em
ev
ic
To ensure that the load sensor measures all the laundry, the drum
must be empty before the washing machine is switched on.
.d
²
The load sensor detects the load level in the washing machine
when the door is open. This is indicated by a progressing bar on
the display panel.
w
Dosing recommendation
w
w
The dosing recommendation indicates a recommended
detergent dosage as a %, depending on the selected programme
and the detected load. The indicated % refers to the
recommendation of the detergent manufacturer.
²
By observing the recommended dosage, you will protect the
environment and reduce your household costs.
Unbalanced load detection system
²
The automatic unbalanced load detection system spins the
laundry several times to ensure even distribution.
For reasons of safety the speed is reduced or does not perform
a spin cycle if the washing is very unevenly distributed.
Distribute small and large items of washing in the drum. Faults,
what to do? ~ Page 50
41
Care and maintenance
eaniClgandmi ntencea
ã Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
Switch off the appliance. Pull out the mains
plug!
ã Caution!
ic
ã Caution!
em
an
ua
ls
.e
u
Fire and explosion hazard!
If solvent cleaning agents, e.g. petroleum
ether, are used in the washing machine,
components may be damaged and toxic
fumes generated.
Do not use solvent-based cleaning agents.
w
w
w
.d
ev
Washing machine may be damaged!
If solvent cleaning agents, e.g. petroleum
ether, are used on the washing machine,
the surfaces may be damaged.
Do not use solvent-based cleaning agents.
Machine housing/Control panel
Ø Remove detergent residue immediately.
Ø Wipe with a soft, damp cloth.
Ø Do not clean the appliance with a water jet.
Drum
Use chlorine-free cleaning agent, not steel wool.
42
Descaling
Not required if detergent dosed correctly. However, if this does
occur, follow the instructions of the descaling agent
manufacturer. Suitable descalers can be purchased on our
website or from customer service. ~ Page 52
i-Dos Clean the detergent drawer
Ø Drain dispensers
ua
ls
.e
u
The dispensers have drainage openings with removable
stoppers in the front area. To drain the dispensers, first
remove the drawer handle as illustrated:
1. Open detergent drawer.
w
.d
ev
ic
em
an
2. Pull release lever (A) on the back of the drawer handle
(bottom middle) gently towards yourself and
simultaneously ...
w
w
... pull up released drawer handle (B).
3. To drain the the dispensers, carefully remove the
respective sealing plug and drain the contents into a
suitable receptacle.
4. Reinsert sealing plug all the way.
43
Ø Cleaning dispensers/detergent drawer
To clean the drained dispensers, the detergent drawer can
be completely removed.
²
1. Drain dispensers before removing them.
Re-attach drawer handle only after cleaning.
2. Open drawer.
3. Press release lever and completely remove drawer.
an
ua
ls
.e
u
4. Carefully remove drawer cover.
ã Caution!
w
w
w
.d
ev
ic
em
Detergent drawer may be damaged!
The detergent drawer contains electrical
components. They may be damaged if they
come into contact with water.
– Do not clean the cover in the dishwasher
and do not immerse in water.
– Protect rear drawer plug from moisture,
detergent or softener residue; if required
clean outer surfaces with a soft, damp
cloth. Dry before re-inserting.
5. Clean tray and cover with soft, damp cloth or hand
shower. Clean inner surface also with a soft, damp cloth.
44
6. Dry tray and cover and re-assemble.
7. Push on drawer handle from above until it locks in place.
8. Push in detergent drawer all the way.
.e
u
Drain pump blocked
ls
ã Warning!
ic
.d
ev
Turn the tap off to prevent more water from flowing in and to
ensure that it is drained via the pump.
w
w
1. Switch off the appliance. Pull out the mains plug!
2. Open service flap.
w
²
em
an
ua
Danger of scalding!
Wash liquor is hot when washing at high
temperatures. You may be scalded if you
touch the hot wash liquor.
Allow detergent solution to cool down.
3. Take the drainage hose out of the holder.
45
4. Remove sealing cap, allow detergent solution to flow out.
Have a suitable container ready.
Push up the closing cap and place the drain hose back in its
holder.
Note: Residual water may run out.
5. Carefully unscrew the pump cover. Clean the interior, pump
cover thread and pump housing (fan impeller in the
detergent-solution pump must rotate).
6. Reinsert and screw on pump cover. Handle should be
vertical.
u
7. Close the service flap. If required, lock disengaged service
ls
ua
To prevent unused detergent from flowing into the outlet during
the next wash cycle: Pour 1 litre of water into dispenser À Á
and start the Drain programme.
em
an
²
.e
flap beforehand.
ic
Drainage hose on the siphon blocked
ev
1. Switch off the appliance. Pull out the mains plug!
.d
Note: Residual water may run out!
w
w
2. Loosen hose clip, carefully remove drainage hose.
3. Clean drainage hose and siphon spigot.
4. Re-attach drainage hose and secure connection point with
w
hose clip.
46
Filter blocked in water inlet hose
u
First, release water pressure in the supply hose:
1. Turn off the tap!
2. Select any programme (except Spin/Drain).
3. Select Start/Pause Ü. Leave programme for approx. 40
seconds.
4. Press the # button. Appliance is switched off. Pull out the
mains plug!
5. Clean the filter:
Disconnect the hose from the water tap.
Clean filter with small brush.
ls
.e
and/or for standard and Aqua-Secure models:
ic
em
an
ua
Remove hose from the rear of the appliance.
w
w
w
.d
ev
Take out filter with pliers and clean.
6. Connect the hose and check for leaks.
47
Emergency lock release, e.g. if power
failure occurs
The programme continues running when the power supply is
restored. If the washing is still to be removed, the door can be
opened as described below:
ã Warning!
.e
u
Danger of scalding!
Wash liquor and washing may be hot.
If touched, there is a risk of scalding.
If required, leave to cool down.
ls
ã Caution!
.d
ev
ic
em
an
ua
Danger when reaching into/gripping the
rotating drum!
If you reach into the rotating drum, you may
injure your hands.
Do not grip the rotating drum. Wait until the
drum stops rotating.
w
ã Caution!
w
w
Water damage possible!
Leaking water may cause damage.
Do not open the door if you can still see
water through the glass.
1. Switch off the appliance. Pull out the mains plug!
2. Drain the water.
3. Pull down emergency release with a tool and release.
Door can then be opened.
48
Information on the display panel
Display
Cause/Remedy
The door cannot be
locked, please open
the door again, then
close it and select
"start/pause".
– Washing may be caught. Please open and close washing
machine door again and select Start/Pause Ü .
– If required, shut washing machine door or remove washing and
shut again.
– If required, switch appliance off and on again; set programme
and make individual settings; start programme.
u
Push in detergent drawer correctly. ~ Page 34
ua
Please close
detergent drawer.
Set i-Dos iIô, i-Dos ô to off.
Call customer Service. Appliance can continue to be operated with
manual dosage. ~ Page 38
.e
i-Dos iIô, i-Dos ô
error; deactivate
i-Dos iIô, i-Dos ô
Level i-Dos container below minimum, Top up ~ Page 34
ls
Please re-fill
i-Dos iIô, i-Dos ô
container
– Turn on tap fully.
– Supply hose kinked/jammed.
– Water pressure too low. Clean the filter. ~ Page 47
Please clean pump
– Drain pump blocked. Clean the drain pump.
– The water drainage pipe/drain hose is blocked. Clean the
drainage hose on the siphon. ~ Page 46
Pause: Reload is not
possible
Water level or temperature is too high.
Select Start/Pause
Start/Pause Ü to continue the programme.
.d
w
Water level or temperature is too high.
Select Start/Pause Ü to continue the programme.
w
w
Door cannot be
unlocked: Water
level or temperature
is too high
ev
ic
em
an
Please open tap
aquaStop has been
activated!
Please call customer
service
not applicable without Aqua-Stop
Water in the base pan, appliance leaking.
Call customer service! ~ Page 52
Auto power-off in ...
seconds,
Appliance automatically switches off after ... seconds if it is not
operated for a prolonged period. In order to cancel the
programme, press any button. ~ Page 40
Water cooling
To protect the wastewater pipes, the hot detergent solution is
cooled before being drained.
Other displays
Error E: XXX
Switch off appliance, wait 5 seconds and switch on again. If the
display is indicated again, call customer service. ~ Page 52
49
Faults, what to do?
Faults
Cause/Remedy
Water is running out.
– Correctly attach/replace drainage hose.
– Tighten screw-fitting on the supply hose.
Water not flowing in.
Detergent not
washed in.
–
–
–
–
Washing-machine
door cannot be
opened.
– Safety function active. Stop programme?
– Rinse Hold $ (without final spin) selected?
– Can be opened via emergency release only? ~ Page 48
Programme does
not start.
– Start/Reload Ü or Finish in time selected?
– Door closed?
– Childlock active? Deactivate.
Detergent solution is
not drained.
– Rinse Hold $ (without final spin) selected?
– Clean the drain pump.
– Clean outlet pipe and/or drainage hose.
Water not visible in
the drum.
Not a fault – water below the visible area.
Spin result not
satisfactory.
Washing wet/too
damp.
– Not a fault – unbalanced load detection system has stopped the
spin cycle, washing unevenly distributed.
Distribute small and large items of washing in the drum.
– Less Ironing æ selected?
– Too low speed selected? ~ Page 23
Not a fault – unbalanced load detection system adjusts imbalance.
w
w
Spin cycle actuated
several times.
w
.d
ev
ic
em
an
ua
ls
.e
u
Start/Reload Ü not selected?
Tap not open?
Filter blocked? Clean the filter. ~ Page 47
Supply hose kinked or jammed?
Residual water in the
dispenser for care
product.
– Not a fault – effect of the care product not impaired.
– If required, clean insert.
Odour formation in
the washing
machine.
Run Cotton 90 °C programme without washing.
Use standard detergent.
Loud noise
formation, vibrations
and “wandering”
during spin cycle.
– Appliance aligned?
Align the appliance. ~ Page 65
– Appliance feet fixed?
Secure appliance feet. ~ Page 65
– Transportation safety devices removed?
Remove transportation protection devices. ~ Page 59
50
Cause/Remedy
Display panel/
indicator lights do
not function while
the appliance is
running.
– Power failure?
– Fuse tripped? Switch on/replace fuse.
– If the fault occurs repeatedly, call customer service. ~ Page 52
The programme
takes longer than
usual.
– Not a fault – unbalanced load detection system adjusts
imbalance by repeatedly distributing the washing.
– Not a fault – foam detection system active – several rinse cycles
are switched on.
Detergent residue
on the washing.
– Occasionally phosphate-free detergents contain water-insoluble
residue.
– Select Rinsing or brush the laundry after washing.
In the pause status
Start/Reload Ü
flashes very quickly
and a signal sounds.
– Water level too high. Washing cannot be reloaded. Immediately
close washing machine door.
– Select Start/Reload Ü to continue the programme.
.e
u
Faults
w
w
w
.d
ev
ic
em
an
ua
ls
If a fault cannot be rectified (switching the machine on and off) or a repair is required:
– Switch off the appliance and pull out the mains plug.
– Turn off the tap and call customer service. ~ Page 52
51
Customer service
If you cannot rectify the fault yourself, Faults, what to
do?~ Page 50, please contact our customer service. We will
always finds a suitable solution to avoid unnecessary visits by
technicians.
Please give customer service the product number (E-Nr.) and the
production number (FD) of the appliance.
(1U
)'
Production number
ls
.e
u
Product number
These instructions can
be found on: inside of
washing machine
door */open service
flap * and rear of the appliance.
* depending on model
w
w
w
.d
ev
ic
em
an
ua
Rely on the competence of the manufacturer.
Contact us. You can therefore be sure that the repair is carried
out by trained service technicians who carry original spare parts.
52
Standard accessories
singthelceInianappl
GHSHQGLQJRQPRGHO
$TXD6WRS
6WDQGDUG$TXD6HFXUH
0DLQVFDEOH
:DWHURXWOHW
.e
u
:DWHULQOHW
.d
ev
6SDQQHU
(OERZ
IRUVHFXULQJWKH
ZDWHURXWOHWKRVH
ic
em
&RYHUVZLWKKRVHFOLS
an
ua
ls
,QVWUXFWLRQPDQXDODQG
,QVWDOODWLRQLQVWUXFWLRQV
w
w
w
Also required for connection of the water drainage hose to a
siphon:
1 hose clip Ø 24–40 mm (DIY store) is also required for
connection to a siphon. Connecting the water ~ Page 63
Useful tools:
Ø Spirit level for alignment.
Ø Socket wrench
size 13: for loosening the transportation protection devices
~ Page 59 and
size 17: for aligning the appliance feet. ~ Page 65
53
Hose and cable lengths
GHSHQGLQJRQPRGHO
&RQQHFWLRQRQOHIWVLGH
&RQQHFWLRQRQULJKWVLGH
RU
aFP
aFP
aFP
aFP
aFPaFP
.e
If the hose holders are used, the possible hose lengths are
reduced!
ls
²
PD[
FP
u
aFPaFP
ic
em
an
ua
Available from dealer/customer service:
Ø Extension for Aqua-Stop or cold water inlet hose
(approx. 2.50 m).
Order no. WMZ2380, WZ10130, CZ11350, Z7070X0
Ø Longer supply hose (approx. 2.20 m), for standard mod
model.
ev
Technical specifications
w
w
w
.d
Dimensions
60 x 59 x 85 cm
(width x depth x height)
depending on modell: 63–83 kg
Weight
Mains connection
Nominal voltage 220–240 V, 50 Hz
Nominal current 10 A
Nominal power 2300 W
Water pressure
100–1000 kPa (1–10 bar)
54
Installation
²
Humidity in the drum is caused by the final inspection.
Secure installation
ã Warning!
ic
ev
ã Caution!
em
an
ua
ls
.e
u
Risk of injury!
– The washing machine is heavy – caution:
take care when lifting it.
– If the washing machine is raised by
protruding components (e.g. washing
machine door), the components may
break off and cause injuries.
Donot lift the washing machine by its
projecting parts.
w
w
w
.d
Risk of stumbling!
If the hoses and power cord are installed
improperly, there is a risk of tripping and
injury.
Lay hoses and cables in such a way that
there is no risk of stumbling.
ã Caution!
Washing machine may be damaged!
– Frozen hoses may tear/burst.
Do not install the washing machine in an
area where there is a risk of frost or
outdoors.
55
²
– If the washing machine is raised by
protruding components (e.g. washing
machine door), the components may
break off and the washing machine may
be damaged.
Donot lift the washing machine by its
projecting parts.
– In addition to the safety information listed here, the local
water and electricity supplier may have special requirements.
– If in doubt, have the appliance connected by a technician.
ã Warning!
.d
ev
ic
em
an
ua
ls
.e
u
Risk of injury!
– The washing machine is heavy –
caution: take care when lifting it.
– If the washing machine is raised by
protruding components (e.g. washing
machine door), the components may
break off and cause injuries.
Do not lift the washing machine by its
projecting parts.
w
w
ã Caution!
w
Risk of stumbling!
If the hoses and power cord are installed
incorrectly, there is a risk of tripping and
injury.
Lay hoses and cables in such a way that
there is no risk of stumbling.
ã Caution!
Washing machine may be damaged!
– Frozen hoses may tear/burst.
Do not install the washing machine in an
56
– In addition to the safety information listed here, the local
water and electricity supplier may have special requirements.
– If in doubt, have the appliance connected by a technician.
.e
u
²
area where there is a risk of frost or
outdoors.
– If the washing machine is raised by
protruding components (e.g. washing
machine door), the components may
break off and the washing machine may
be damaged.
Do not lift the washing machine by its
projecting parts.
ua
Stability is important to prevent the washing machine from
wandering!
– The installation area must be firm and level.
– Soft floors/floor coverings are not suitable.
em
an
²
ls
Installation area
ev
ic
Installing the appliance on a base or on a wooden joist
ceiling
.d
ã Warning!
w
w
w
Washing machine may be damaged!!
The washing machine may wander during
the spin cycle and topple/fall off the base.
Always secure the washing machine feet
with fixing brackets.
Holding brackets: order no. WMZ 2200,
WX 9756, CZ 110600, Z 7080X0
²
If installing on a wooden joist ceiling:
– If possible, install the washing machine in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to
the floor.
57
Appliance installed under/between kitchen units
ã Warning!
– 60 cm cavity width required.
– Install washing machine only under a continuous worktop
connected firmly to the adjacent cupboards.
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
²
Danger of death from electric shock!
Danger of death if live parts are touched.
The appliance cover plate must not be
removed.
58
Remove transportation protection
devices
ã Caution!
ua
ls
.e
u
Washing machine may be damaged!
Transit bolts which have not been removed
may damage e.g. the drum while the
washing machine is running.
Before using the appliance for the first time,
remove the 4 transportation protection
devices completely and keep in a safe
place.
an
ã Caution!
.d
ev
ic
em
Washing machine may be damaged!
To prevent damage in transit when
transporting the washing machine
subsequently, always re-install the transit
bolts prior to transportation.
w
w
w
Keep screw and sleeve screwed together.
1. Take the hoses out of the holders.
59
2. Take hoses out of the elbow and remove elbow.
3. Loosen and remove all 4 transportation lock screws.
ua
ls
.e
u
4. Take the power cord out of the holders. Remove sleeves.
ev
ic
em
an
5. Prepare/separate cover.
w
w
w
.d
6. Insert covers.
²
Lock covers firmly by pressing on the locking hook.
7. Insert hose holder.
8. Secure hoses in the hose holders.
60
Connecting the water
ã Warning!
– To prevent leakage or water damage, follow the instructions
in this chapter!
– Operate the washing machine with cold drinking water only.
– Do not connect to the mixer tap of an unpressurised hotwater apparatus.
– Use only the supplied inlet hose or one purchased from an
authorised specialist outlet, not a used one!
– If in doubt, have the appliance connected by a technician.
ua
ls
.e
u
²
Danger of death from electric shock!
Danger of death if live parts are touched.
Do not immerse Aqua-Stop safety device in
water (contains an electric valve).
em
Water inlet hose: do not kink, crush, modify or sever (strength is
no longer guaranteed).
ic
²
an
Water inlet hose
w
w
.d
ev
Optimum water pressure in the mains: 100–1000 kPa (1–
10 bar)
Ø When the tap is turned on, the water flow is at leas
least 8 l/min.
Ø If the water pressure is higher, install a pressure reducing
valve.
w
1. Connect the water supply hose.
ã Warning!
Threads for screw connections may be
damaged!
If the screw connections are tightened too
tightly using a tool (pliers), the threads may
be damaged.
Tighten plastic screw-fittings by hand only.
61
to the tap (¾" = 26.4 mm):
PD[
ƒ
PLQPP
PD[
ƒ
Aqua-Stop and Aqua-Secure Standard
on the appliance:
for Standard and Aqua-Secure models
2. Carefully turn on the tap and check that the connection points
u
.e
Screw connection is under water pipe pressure.
ua
ls
²
are not leaking.
– Do not kink or protract the the water supply hose.
– Height difference between the placement area and drainage
point: 0–maximum 100 cm
ic
em
²
an
Water drainage hose
ev
Drainage into a wash basin
.d
ã Warning!
w
w
w
Water damage possible!
If the attached drainage hose slips out of
the washbasin due to high water pressure
when draining the washing machine,
leaking water may cause damage.
Secure the drainage hose to prevent it from
slipping out of the sink.
62
ã Caution!
u
The appliance may be damaged.
If the end of the drainage hose is immersed
in the drained water, water may be drawn
back into the appliance!
– The plug must not be in the plug hole.
– When the water is being pumped out of
the washing machine, check that the
water drains away quickly enough.
– The end of the drainage hose must not
be immersed in the drained water!
ev
ã Warning!
ic
Drainage into a siphon
em
an
ua
ls
.e
Installing the drainage hose:
w
w
w
.d
Water damage possible!
If the drainage hose slips off the siphon
connection due to high water pressure
when draining the washing machine,
leaking water may cause damage.
Connection point must be secured with
hose clip, Ø 24–40 mm (specialist outlet).
Connecting
63
Drainage into a plastic pipe with rubber sleeve or into
a gully:
ã Warning!
Water damage possible!
If the drainage hose slips off the plastic
pipe due to high water pressure when
draining the washing machine, leaking
water may cause damage.
Secure the drainage hose to prevent it from
slipping out of the sink.
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
Connecting
64
Alignment
1. Loosen lock nut in a clockwise direction with a wrench.
2. Check alignment of the washing machine with a spirit level
an
All four feet must be firmly on the floor.
The washing machine must not wobble!
3. Tighten the lock nut against the housing.
Grip the foot and do not adjust the height.
w
w
– The lock nuts on all four appliance feet must be screwed
tightly against the housing!
– Loud noise formation, intense vibrations and “wandering”
may be due to incorrect alignment!
w
²
.d
ev
ic
em
²
ua
ls
.e
u
and, if required, correct. Adjust the height by rotating the foot.
65
Electrical connection
Electrical safety
ã Warning!
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
Danger of death from electric shock!
Danger of death if live parts are touched.
– Never pull out the mains plug by tugging
the power cord.
– Insert/pull out the mains plug with dry
hands only.
– Never pull out the mains plug during
operation.
– Connect the washing machine to an
alternating current via a correctly
installed earthed socket only.
– The mains voltage and voltage
specifications on the washing machine
(appliance rating plate) must match.
– Connected load as well as required fuse
are indicated on the appliance rating
plate.
Ensure that:
– Mains plug and socket match fit.
– Cable cross-section is adequate.
– Earthing system has been installed
correctly.
– A damaged power cord may
be replaced by an electrician only.
A replacement mains cable can be
obtained from customer service.
– Do not use multiple plugs/couplings or
extension cables.
66
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
– If a residual-current-operated circuit
breaker is used, use only a type which
features this symbol: z.
Only this symbol guarantees compliance
with currently valid regulations.
– The mains plug must be accessible at all
times.
67
Before the 1st washing
²
The washing machine must have been installed and connected
properly. See chapter Installing ~ Page 65
1. Check the machine.
Never switch on a damaged machine. Inform your customer
service. ~ Page 52
2. Fill dispensers ô / M ô . ~ Page 34
3. Remove protective film from the fascia.
4. Insert mains plug.
5. Turn the tap on.
6. Switch on the appliance.
7. Close the washing machine door. Do not load any washing.
8. To prevent unused detergent from flowing into the outlet
during the first wash: Pour 1 litre of water into dispenser À Á
and start the Drain programme.
9. Select and start the Cotton 90 °C programme.
10. When the programme ends, switch off the appliance.
.d
ev
ic
em
an
ua
ls
.e
u
²
The washing machine was inspected thoroughly before leaving
the factory. To remove any water left over from testing
procedures, the first washing cycle should be carried out without
laundry in the machine.
w
w
w
Your washing machine is now ready for use.
68
Transportation, e.g. if moving house
Preparatory work
1. Turn off the tap.
2. Release the water pressure in the supply hose.
Maintenance – Filter in the water inlet hose ~ Page 47
3. Drain any residual detergent solution.
Maintenance – Drain pump blocked
u
4. Isolate the washing machine from the power supply.
5. Remove the hoses.
6. Drain dispensers. ~ Page 43
.e
Installing transportation protection devices
em
an
ua
ls
1. Remove covers and keep in a safe place.
ic
If required, use a screwdriver.
w
w
w
.d
ev
2. Insert all 4 sleeves.
²
Clamp mains cable on the holders. Insert and tighten the
bolts.
Before switching on the
appliance:
– Always remove the transportation protection devices!
~ Page 59
– To prevent unused detergent from flowing into the outlet
during the next wash cycle: Pour 1 litre of water into
dispenser À Á and start the Drain programme.
69
Index
A
Alignment, 65
Anti-stain system, 33
B
Basic Settings 3 sec., 11
Button
ecoPerfect, 11, 17, 30
Finish in, 11, 17, 30
i-Dos i Iô, 11, 18, 31
i-Dos ô, 11, 18, 31
C
Cancelling
the programme, 20
Care, 42
Drum, 42
Machine housing/Control
panel, 42
Changing
the programme, 20
Childlock, 19, 30
D
Descaling, 43
Detergent drawer, 10
Discolouring, 28
Display panel, 11
E
ecoPerfect, 11, 17, 30
Electrical connection, 66
Emergency lock release, 48
Aqua-Sensor, 41
Automatic programmes, 28
Options, 11, 17
speedPerfect, 11, 17, 30
Spin, 11, 17, 30
Start/Reload, 11
Temperature, 11, 17, 30
Dosing recommendation, 41
Drain pump blocked, 45
Drum light, 14
Dyeing, 28
End of the programme, 21
Extra rinse, 32
F
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
Cleaning
Detergent drawer, 43
the filter, 47
the siphon, 46
Connecting the water, 61
Water drainage, 62
Water supply, 61
Consumption values, 39
Customer service, 52
Fascia, 11
Faults, what to do?, 50
Finish in, 11, 17, 30
G
Getting to know your
appliance, 9
H
Hints and tips, 8
Hose and cable lengths, 54
I
i-Dos, 10, 23, 31
Clean the dispenser, 43
Drain dispensers, 43
Filling dispenser, 34
In daily use, 35
Standard settings, 36
Switching on the
appliance, 34
i-Dos iIô, 11, 18
i-Dos ô, 11, 18
Information on the display
panel, 49
Insert
the laundry, 16
70
Installation, 55
Installing transportation
protection devices, 69
Intended use, 4
L
Less Ironing, 32
Load adjust, 41
Load sensor/Load display, 41
M
Maintenance, 42
Manual dosage, 38
O
Old appliance, 8
Option
Extra rinse, 32
Less Ironing, 32
Pre-wash, 32
Rinse Hold, 32
Silent Wash, 32
Stains, 32
Water Plus, 32
Options, 17, 30
Options button, 11
P
Packaging, 8
Pre-wash, 32
Programme overview, 23
Programme selector, 11
Programme sequence
steps, 19
Programme setting, 16, 17
Programme settings, 30
Protection of the
environment, 8
Q
Quick-reference
R
Rinse Hold, 21, 32
S
Safety instructions, 5
Selecting
the programme, 15
Settings 3 sec., 40
Silent Wash, 32
Soaking, 29
Sorting
the washing, 13
speedPerfect, 11, 17, 30
Spin, 11, 17, 30
Stains, 32
Standard accessories, 53
Starching, 28
Starting
the programme, 18
T
Technical specifications, 54
Temperature, 11, 17, 30
Textileguard, 28
Topping up
washing, 20
Transport bolts, 59
U
Unbalanced load detection
system, 41
Unloading
the laundry, 22
W
Water Plus, 32
instructions, 12
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
Insert the laundry, 14
Insert the washing
the laundry, 15
71
Aqua-Stop warranty
For appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of
sale and in addition to our appliance warranty we shall pay damages
under the following conditions:
1. If water damage is caused by a fault in our water safety system, we
em
an
ua
ls
.e
u
Aqua-Stop have been correctly installed and connected according to
our instructions; this also includes a correctly installed Aqua-Stop
extension (original accessory).
4. Our guarantee does not apply to defective cables/hoses or to fittings
up to the connection on the tap.
5. Appliances which feature Aqua-Stop can be left unattended during
operation and it is not necessary to turn off the tap afterwards.
6. The tap should only be turned off if you are away for a prolonged
period, e.g. several weeks holiday.
w
w
w
.d
ev
ic
To book an engineer visit and product advice
GB
0844 8928999
Calls from a BT landline will be charged at
up to 3 pence per minute.
IE
01450 2655
Please find the contact data of all countries in the enclosed customer
service list.
Siemens-Electrogeräte GmbH
Carl-Wery-Str. 34, 81739 München
Germany
9000755818 (9202)
*9000755818*
shall make reparation for the damage with respect to private users.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and