Bosch PPQ716B21A Operating instructions

This cooktop is for use with Natural Gas and Universal LPG
Leave this instructions with the owner
PPH616B21A, PPQ716B21A
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
Ú Table of contents
ecuIn[rotis]deumyosjatn
Safety considerations................................................................ 2
For your safety.....................................................................................2
What to do if you smell gas ..............................................................2
Warnings...............................................................................................2
Installation .................................................................................. 3
Warnings...............................................................................................2
Statutory requirements.......................................................................3
Preparing to install..............................................................................3
Clearances ...........................................................................................4
Installation of cooktop into the kitchen bench ..............................4
Connection ...........................................................................................5
Converting the cooktop from Nat. Gas to Universal LPG ...........6
Changing the nozzles of the burners on the cooktop .................6
Adjustment of the taps.......................................................................6
Operating instructions ...............................................................7
Burner locations..................................................................................7
Accessories .........................................................................................7
Operation..............................................................................................8
Cooking pans ......................................................................................9
Cleaning and maintenance...............................................................9
Service ............................................................................................... 10
Wiring diagram................................................................................. 11
Produktinfo
Additional information on products, accessories, replacement
parts and services can be found at www.bosch-home.com and
in the online shop www.bosch-eshop.com
Safety considerations
For your safety
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury
or death.
For pressure testing in excess of 3.5 kPa (1/2 psig) the
appliance and its individual shutoff valve must be disconnected
from the gas supply piping system.
Do not store flammable material near this appliance.
Important. When using a very large pot, leave a gap of at least
50 mm (2”) to avoid damaging any parts in bench top wood,
plastic or other non-heat resistant materials. Never leave oil or
hot fat unattended.
Do not spray aerosols in the vicinity of this appliance while it is
in operation.
The surfaces on heating and cooking appliances get hot when
in use. Be careful. Keep children away from the appliance.
What to do if you smell gas
Only use your appliance for the preparation of food and never
for room-heating purposes.
Do not store articles on or against this appliance.
Do not touch any electrical switch; do not use any phone in
your building.
This appliance leaves the factory set for the gas supply
indicated on the data label. Call the Service Centre if it needs
to be altered.
Inmediately call your gas supplier from a neighbour’s phone.
Follow the gas supplier’s instructions.
Do not tamper inside the appliance. If necessary, call your local
Service Centre.
If you cannot reach your gas supplier, call the fire department.
Overheated fat or oil can easily catch fire. Never leave the
appliance unattended when cooking food with fat or oil, e.g. chips.
Do not try to light the appliance.
Installation and service must be performed by an authorised
person.
Warnings
Never pour water on burning fat or oil. DANGER OF BURNS!
Cover the receptacle to smother the flames and turn the
cooktop off.
DO NOT MODIFY THIS APPLIANCE.
In the event of a fault, cut the gas and electricity supplies to the
appliance. Call our Service Centre to repair the fault.
Do not allow the flame to extend beyond the edge of the
cooking utensil. This instruction is based on safety
considerations.
Do not use unstable or uneven-based receptacles on cooking
plates or burners. They may accidentally tip over.
Do not forget that the unit becomes hot when in use. Common
sense is important. Just because the flame is out, does not
mean parts cannot still be hot.
This appliance shall not be used for space heating. This
instruction is based on safety considerations.
If a gas supply knob/valve jams, do not force it. Call your
official Service Centre immediately for them to repair or replace
it.
The illustrations used in this booklet are only intended as a
guide.
Be sure to disconnect the electrical supply before disassembly
of the appliance.
Grids become very hot during use. When operating the
appliance control knobs, take care not to make contact with the
grids.
Keep the appliance area clear and free from combustible
materials, gasoline and other flammable vapours and liquids.
Do not use this appliance neither in marine craft nor in
caravans.
This appliance must be installed in a position with the proper
level of ventilation. Do not obstruct the flow of combustion and
ventilation air.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Cabinets installed above the gas cooktop must have a
minimum clearance of 650 mm (24”).
The gas pressure regulator supplied with the appliance must be
installed in line with the gas pipe. (N.G. only).
2
Make sure you keep these instructions for use and assembly in
a safe place, so that you can hand them on with the appliance
if it ever changes owner.
Note: To avoid jeopardising the electrical safety of the
appliance, it is forbidden to use high-pressure or steam jet
cleaning devices.
SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY
SATISFIED, THE INSTALLER, AND NOT THE
MANUFACTURER, SHALL HELD LIABLE.
Installation
Statutory requirements
Preparing to install
This installation must conform with the following:
Refer to AS/NZS 5601.1 for piping size details. These built-in
cooktops are intended to be inserted in a benchtop cutout.
■
Manufacturer’s Installation instructions
■
Local Gas Fitting Regulations
Only an officially authorised technician should connect the
appliance.
■
Municipal Building Codes
Before you begin, turn off the gas and electricity supply.
■
Refer to AS/NZS 5601.1 for Gas Installations
■
S.A.A. Wiring Code
■
Local Electrical Regulations
■
Any other statutory regulations
D
5
PD[
5
E
PLQ
PLQ
D
5
B
E
PD[
5
PLQ
PLQ
3
Before connecting the unit, check whether the local connection
conditions (type of gas) are compatible with the unit’s setting.
Observe any special conditions imposed by local suppliers
(utilities). The specifications of this cooktop are stated on the
data label located on the bottom of the cooktop base.
A duplicate data label is supplied for adhesion to an accessible
location near the hotplate if the data label on the base of the
hotplate cannot be accessed when the hotplate is installed.
Clearances
A range hood fitted above the top must be installed according
to the installation instructions for the range hood. A minimum
distance of 650 mm is required for a range hood and 750 mm
for an exhaust fan.
Any adjoining wall surface situated within 200 mm from the
edge of any hob burner must be a suitable non-combustible
material for a height of 150 mm for the entire length of the hob.
Any combustible construction above the hotplate must be at
least 650 mm above the top of the burner and no construction
shall be within 450 mm above the top of the burner.
Installation of cooktop into the kitchen bench
Side clearances: If the distance measured from the periphery of
the nearest burner to any vertical surface is less than 200 mm,
the surface shall be protected in accordance with clauses
6.10.1.2 of AS/NZS 5601.1.
Make an appropriate size cut in the worktop surface,
depending on the installation method: standard (a) or flush (b).
For flush installation:
■
All cuts in the worktop surface should be done by a
specialised shop.
■
The cuts should be clean and precise, as the cut edge is on
the surface. The stability of the furniture should also be
ensured after cutting work.
■
Use only specially designed work surfaces, resistant to hightemperature and water (e.g. natural stone or tiled).
■
Surrounding furniture must be resistant to temperatures up to
90 °C.
Installation procedure:
a) Standard installation
Depending on the model, the adhesive seal may be factoryfitted. If this is the case, it should not be removed under any
circumstances, since the adhesive seal prevents leaks. If the
seal has not been factory-fitted, apply it to the underside of the
hob.
Fitting the appliance onto the kitchen unit:
PLQ
1. Remove the clips from the accessory bag and screw them
into the position indicated so that they can turn freely.
PLQ
2. Insert and centre the hob.
Press the sides of the hob until it is supported around its
entire perimeter.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the work
surface is.
A minimum depth of 50 mm from the top of the worktop
surface must be provided for the appliance.
If the base of the hotplate can be touched, a protecting shield
must be fitted.
■
The shield must be at least 10 mm from the lowest part of the
hotplate and must be capable of withstanding the appliance
temperatures. Minimum thickness of benchtop is 30 mm.
■
The shield material must be mdf or similar with minimum
thickness of 12 mm.
■
The shield overall dimensions must be 560 mm wide x
480 mm deep.
■
Provide cut-out in right hand rear of shield of 80 mm wide x
80 mm deep to provide for gas regulator / LP connection
fitting.
After installation of the shield the clearance around the top and
sides of shield will allow adequate ventilation. Ensure the side
and top clearances are not obstructed.
PLQ
PD[
PLQ
PLQ
PD[
PLQ
PLQ
b) Flush installation
1. Complete a normal installation of the appliance making sure
that it is surrounded by a uniform slot. The hob surface
should be slightly below the work surface.
For tile worktops, if necessary, raise the bearing surfaces with
strips resistant to water and temperatures.
2. Check the operation and position of appliance.
3. Fill the gap between the worktop and hob with conventional
If an oven is positioned below the cooktop the barrier does not
need to be fitted, but a space of 35 mm must be maintained
between the underside of the cooktop and the top of the oven.
4
silicone adhesive appropriate in the colour you desire.
Note: If unsuitable silicone adhesive is used on natural stone
surfaces then this can produce colours that can not be
removed. Our Technical Assistance Service can provide you
with the most suitable glue (code 310818). Please note the
manufacturers instructions for use.
Fit regulator (N.G.) or a test point (Universal LPG) directly to the
R 1/2’’ connection.
4. Smooth the silicone adhesive with a scraper or wet finger
moistened with soap and water before it forms a layer.
5. Allow the silicone adhesive to dry before using the appliance.
VLOLFRQH
“ Direction of gas flow is indicated on the rear of the regulator.
Position of the inlet connection:
“ a
a¸
Connection
a
Electrical
An electrical 10 amp socket needs to be within 1 m of the
hotplate to allow electrical connection. The socket must remain
accessible after installation of the appliance.
Important notes:
■
■
This appliance is connected to the mains (240 VAC) by
means of the connecting lead which must be fixed to the
kitchen unit to prevent it from coming into contact with hot
parts of the cooktop (or an oven installed underneath) and
remain accessible after installation of the cooktop.
When making this connection make sure that the lead cannot
come into contact with hot parts of the cooktop.
This appliance must be earthed. When connecting the
cooktop ensure that the earth wire is connected first and that
all wires are connected to the correct terminals.
99 a
/
1
9
9
Gas
During the planning stage, consider the position of supply
connections.
The cooktop must be connected to the gas supply with
upstream connection of an isolation valve in accordance with
the respectively valid regulations. We recommend that the
isolation valve be fitted prior to the cooktop to enable isolation
of cooktop from gas supply. The valve must be easily
accessible at all times.
To find out the factory set gas type, see bottom of cooktop next
to gas connection.
Remove plastic cap from gas supply line prior to installation.
Use pipe compound or thread sealant, properly theaded pipes
and careful assembly procedure so that there is no cross
threading, etc., which might cause damage or leakage.
Make sure that all connections peformed are free of leakage.
The manufacturer does not accept any liability for leakage on
connections performed by the installer or if the L-tube is moved
or twisted.
There are two ways to carry out the connection to the main gas
line:
■
The hotplate can be connected with rigid pipe as specified in
AS/NZS 5601.1
■
Flexible Hose: If installing with a hose assembly, install with a
hose assembly that complies with AS/NZS 1869 (AGA
Approved), 10 mm ID, class Bor D, no more than 1,2 m long
and in accordance with AS/NZS 5601.1.
Ensure that the hose does not contact the hot surfaces of the
hotplate, oven, dishwasher or any other appliance that may
be installed underneath or next to the hotplate. The hose
should not be subjected to abrasion, kinking or permanent
deformation and should be able to be inspected along its
entire length with the cooktop in the installed position. Unions
compatible with the hose fittings must be used and all
connections tested for gas leaks.
The supply connection point shall be accessible with the
appliance installed.
WARNING: Ensure that the hose assembly is restrained from
accidental contact with the flue outlet of an underbench oven.
Before Leaving- Check all connections for gas leaks with soap
and water. DO NOT use a naked flame for detecting leaks.
Ignite all burners both individually and concurrently to ensure
correct operation of gas valves, burners and ignition. Turn gas
taps to low flame position and observe stability of the flame for
each burner individually and all together. Adhere the duplicate
data plate to an accessible location near the hotplate. When
satisfied with the hotplate, please instruct the user on the
correct method of operation. In case the appliance fails to
operate correctly after all checks have been carried out, refer to
the authorised service provider in your area.
It should be expressly noted that we cannot accept any liability
for direct or indirect damage caused by wrong connection,
leakage or improper installation. When being repaired, the
appliance must always be disconnected from the mains supply;
if required, notify our customer service.
5
Converting the cooktop from Nat. Gas to
Universal LPG
Adjustment of the taps
To change injectors
2. Remove the control knobs from the taps. It has a flexible
All work involved in installation, setting and adaptation to a
different gas type must be carried out by authorised personnel
from our Service Centre and must comply with current
regulations and the conditions laid down by the local gas
company.
1. Set the control knobs to minimum.
rubber valve reinforcing ring. Press with the tip of the
screwdriver to access the tap's adjusting screw.
Request change-over injectors from our customer service
deparment (refer injector chart below for sizes).
Natural Gas
Universal LPG
Burner
Hourly Gas
Injector Hourly Gas
Injector
Consumption mark
Consumption mark
(MJ)
(MJ)
Auxiliary
3,60
90
3,50
50
Semi-rapid
6,50
120
6,00
67
Rapid
10,80
155
10,00
85
Double flame 12,00
160
11,00
91
Triple flame
182
13,50
100
16,00
Before conversion the cooktop must be disconnected from the
electricity and gas valves must be turned to the OFF position.
Changing the nozzles of the burners on the
cooktop
1. Remove the pan supports, burner covers and diffusers.
2. Change the nozzles using the spanner provided by our
Service Centre (code 340847, for double and triple flame
burners code 340808), taking special care to ensure that the
nozzle does not fall when it is removed from the burner or
when fitted.
Ensure that it is completely tightened in order to guarantee
the seal.
Never remove the valve reinforcing ring. The valve
reinforcing rings guarantee the watertightness of the
appliance's interior from liquids and dirt, which might
otherwise prevent its correct operation.
3. Adjust the minimum ring setting by turning the by-pass screw
using a flat head screwdriver.
To adjust the minimum flame for N.G. replace the control knob
onto the spindle, light the gas and turn the control knob to the
small flame position. Screw the adjustment screw anticlockwise to estabilish a minimum stable flame position. The
flame should remain alight and not burn back to the injector
when the valve is turned quickcly from ‘Full On’ to the
“Minimum flame” position and back a few times. To adjust the
minimum flame position for ULPG the screw must be fully
tightened down clockwise.
If the by-pass screw cannot be accessed, disassemble the
grease drip tray, which is fitted to the hob with a series of
screws. The following steps must be taken to remove it:
1. Remove all pan supports, burner caps, diffusers and control
knobs.
2. Remove the screws from the burners.
3. To reinstall the appliance, proceed in the reverse order to
disassembly.
Never remove the tap spindle. In the event of a malfunction,
change the whole tap.
Important: After finishing, stick the sticker, indicating the new
gas type, close to the specifications plate.
6
Operating instructions
Burner locations
334%$
33+%$
1
1
2
2
1 Pan supports
2 Control knobs
3 Auxiliary burner (up to 1 kW)
4 Semi-rapid burner (up to 1.75 kW)
5 Rapid burner (up to 3 kW)
6 Double-flame wok burner (up to 3.3 kW)
7 Triple-flame wok burner (up to 4 kW)
Accessories
The following accessories can be purchased from the
Technical Assistance Service:
Additional wok pan support
Simmer Cap
Only for use on wok burners
with pans with a round base.
Lid specially designed to
cook at minimum power. For
its use, the Simmer Cap
needs to be placed on the
auxiliary burner cap.
The additional wok pan support should be used to prolong the appliance's useful
life.
Additional coffee maker
support
Wok pan
The wok pan diffuses intense
heat uniformly, so that the
food is cooked in less time
and using less oil.
Only for use on the auxiliary
burner with pans which are no
more than 12 cm in diameter.
Always follow the manufacturer's instructions when
cooking with a wok pan.
--------
Simmer Plate
This accessory has been
designed to reduce the level
of heat at the lowest power
setting.
Place the accessory directly
on the pan support with the
cones facing upwards, never
directly over the burner. Centre the pan over the accessory.
Code
HEZ298126 Additional wok pan support: cast iron (3.3 kW)
HEZ298127 Additional wok pan support: cast iron (4 kW)
HEZ298110 Additional wok pan support: steel enamel
(3.3- 4 kW)
HEZ298114 Additional coffee maker support
HEZ298105 Simmer Plate
HEZ298128 Simmer Cap
HEZ298103 Wok pan
The manufacturer accepts no liability if these accessories are
not used or are used incorrectly.
7
Operation
Safety system
There are indications to show which burner each control knob
operates.
Depending on the model, your hob may have a safety system
(thermocouple) that prevents the flow of gas if the burners
accidentally switch off.
It is essential to ensure that all the burner parts and pan
supports are correctly installed for the appliance to work
correctly. Do not swap the burner caps around.
WKHUPRFRXSOH LJQLWLRQVSDUNHU
To ensure that this device is active:
1. Switch on the burner as usual.
2. Without releasing the control knob, press and hold it down
firmly for 4 seconds after lighting the flame.
Switching off a burner
Turn the corresponding control knob clockwise to the 0 setting.
Power levels
The progressive control knobs can be used to control the
power needed, from minimum to maximum power.
Setting
Large flame
Economy flame
Û
—
˜
Control off
Maximum capacity or aperture and electricity on
Minimum capacity or aperture
Warnings
It is normal to hear a soft whistling noise while the burner is
operating.
Switching on automatically
When first used, it is normal for the burner to give off odours.
This does not pose any risk and does not indicate a
malfunction. They will disappear in time.
If your hob can be switched on automatically (ignition
sparkers):
An orange-coloured flame is normal. This is caused by the
presence of dust in the atmosphere, spilt liquids, etc.
1. Press the chosen burner control knob and turn it
If the burner flames are accidentally blown out, switch off the
burner operating control knob and do not try to relight it for at
least 1 minute.
anticlockwise to the maximum power setting.
While the control knob is still pressed down, sparks are
produced on all burners. The flame ignites.
2. Release the control knob.
3. Turn the control knob to the required setting.
If it does not come on, turn the control knob to the off setting
and repeat the steps above. This time, press and hold the
control knob for longer (up to 10 seconds).
: Risk of deflagration!
If after 15 seconds the flame does not ignite, switch off the
burner and open a nearby window or door. Wait at least one
minute before trying to switch the burner back on.
8
A few seconds after the burner is switched off, a sound (thud)
will be produced. This is not a fault - this means that the safety
device is no longer operating.
Keep the burner as clean as possible. If the ignition sparkers
are dirty they will not light properly. Clean them periodically
using a small non-wire brush. Bear in mind that the ignition
sparkers must not suffer any serious impacts.
Use “Large” setting to bring the pan to the boil, then adjust the
flame between “Large flame” and “Economy flame” to maintain
the required pan temperature.
Important:
The use of a cooktop leads to the production of heat and
moisture in the kitchen. For this reason make sure that the
room is properly ventilated. Keep natural ventilation openings,
such as windows, open or provide a mechanical ventilation
device (e.g. a range hood or overhead exhaust fan). An orangy
flame is normal and simply indicates the presence of salt in the
atmosphere (from cooking). If the flame has yellow patches,
this is not a fault (of any kind).
Cooking recommendation
Burner
Very high - High
Medium
Wok burner
Boiling, steamReheating and keeping
ing, griddling,
things hot: cooked and pretoasting, paellas, cooked dishes
Asian food (wok).
Do not cook without using a lid
and make sure the lid is
properly fitted. This wastes
energy.
Low
Rapid burner Escalopes,
steaks, omelettes, frying
Rice, white
Steaming:
sauce, ragout fish, vegetables
Semi-rapid
burner
Steamed potatoes, fresh vegetables, vegetable
stews, pasta
Reheating, keeping things
hot and making tasty casseroles
Auxiliary
burner
Cooking: casseroles, rice pudding, caramel
Defrosting
Melting: butand slow
ter, chococooking: veg- late, jelly
etables, fruit
and frozen
products
Always centre the pan over the
burner, not to one side.
Otherwise it could tip over.
Do not place large pans on the
burners near the control
knobs. These may be
damaged by the very high
temperatures.
Place the pans on the pan
supports, never directly on the
burner.
Make sure that the pan
supports and burner caps are
correctly positioned before
using the appliance.
Pans should be placed on the
hob carefully.
Do not place anything, eg. flame
tamer, asbestos mat, between
pan and pan support as serious
damage to the appliance may
result.
Do not strike the hob and do
not place excessive weight on
it.
Never use two burners or heat
sources to heat one single
pan.
Do not remove the pan support
and enclose the burner with a
wok stand as this will
concentrate and deflect heat
onto the hotplate.
Do not use large pots or heavy
weights which can bend the pan
support or deflect flame onto the
hotplate.
Do not use grill pans,
earthenware casserole dishes,
etc. for a long period of time
on maximum power.
Cleaning and maintenance
Cleaning
Once the appliance is cool, use a sponge to clean it with soap
and water.
Cooking pans
Suitable pans
The chart below gives the correct pan usage for each burner.
After each use, clean the surface of the respective burner parts
once they have cooled down. If any residue is left (baked-on
food, drops of grease etc.), however little, it will become stuck
to the surface and more difficult to remove later. The holes and
grooves must be clean for the flame to ignite properly.
Burner
Minimum pan
diameter
Maximum pan
diameter
The movement of some pans may leave metal residue on the
pan supports.
Wok burner
22 cm
30 cm
Clean the burners and pan supports using soapy water and
scrub with a non-wire brush.
Rapid burner
22 cm
26 cm
Semi-rapid burner
14 cm
20 cm
Auxiliary burner
12 cm
16 cm
Precautions for use
The following advice is intended to help you save energy and
prevent pan damage:
Use pans which are the right
size for each burner.
Do not use small pans on
large burners. The flame must
not touch the sides of the pan.
Do not use damaged pans,
which do not sit evenly on the
hob. Pans may tip over.
If the pan supports are fitted with rubber rests, ensure that
these are also cleaned. The rests may come loose and the pan
support may scratch the hob.
Always dry the burners and pan supports completely. Water
droplets or damp patches on the hob at the start of cooking
may damage the enamel.
After cleaning and drying the burners, make sure the burner
caps are correctly positioned on the diffuser.
Caution!
■
Do not use steam cleaners. This could damage the hob.
■
Never use abrasive products, steel scourers, sharp
implements, knives, etc. to remove bits of hardened food
from the hob.
■
Do not use knives, scrapers or similar implements to clean
the point where the glass meets the burner trims, the metal
frames or the glass/aluminium panels, if fitted.
Only use pans with a thick, flat
base.
9
Maintenance
Always clean off any liquid as soon as it is spilt. This will
prevent food remains from sticking to the hob surface and you
will save yourself any unnecessary effort.
Never slide pans across the glass surface, as you may scratch
it. In addition, try not to drop heavy or sharp objects on the
glass. Never strike any part of the hob.
Grains of sand that may come from cleaning fruits and
vegetables will scratch the glass surface.
Melted sugar, or foods which contain a lot of sugar which may
have spilt, should be cleaned off the hotplate immediately,
using the glass scraper.
Service
DO NOT MODIFY THIS APPLIANCE.
Only authorized personnel from the Service Centre are qualified
to work on the appliance.
Fault
Sometimes certain faults detected can be easily resolved.
Before calling the Technical Assistance Service, bear in mind
the following advice:
Possible cause
The general electrical sys- Defective fuse.
tem is malfunctioning.
Solution
Check the fuse in the main fuse box and change it
if it is damaged.
The automatic safety switch or circuit breaker has Check the main control panel to see if the autotripped.
matic safety switch or circuit breaker has tripped.
The automatic switching
There may be food or cleaning products stuck
on function does not work. between the ignition sparkers and the burners.
The space between the ignition sparker and the
burner must be clean.
The burners are wet.
Dry the burner caps carefully.
The burner caps are not correctly positioned.
Check that the burner caps are correctly positioned.
The appliance is not earthed, is poorly connected Contact the installation technician.
or the earthing is faulty.
The burner flame is not uni- The burner components are not correctly posiform.
tioned.
The grooves on the burner are dirty.
Correctly place the parts on the appropriate
burner.
Clean the grooves on the burner.
The gas flow is not normal The gas supply is blocked by gas taps.
or there is no gas.
If the gas is supplied from a gas cylinder, check
that it is not empty.
Change the gas cylinder.
The kitchen smells of gas. A gas tap has been left on.
Turn off the taps.
Incorrect coupling of gas cylinder.
Check that the coupling is sound.
Possible gas leak.
Shut off the gas supply, ventilate the premises and
immediately notify an authorised installation technician to check and certify the installation. Do not
use the appliance until ensuring that there is no
gas leak in the installation or appliance itself.
The burner immediately
The control knob was not held down for long
switches off after releasing enough.
the control knob.
The grooves on the burner are dirty.
Any of the following are considered to be abnormal operation
and may require servicing:
■
Yellow tipping of the cooktop burner flame.
■
Sooting up of cooking utensils.
■
Burners not lighting properly.
Gas valves, which are difficult to turn in case the appliance fails
to operate correctly, contact the authorised service provider in
your area.
10
Open all gas taps.
Once the burner is on, hold the control knob down
a few seconds longer.
Clean the grooves on the burner.
Wiring diagram
A
Switch
B
Blue wire
C
Brown wire
D
Terminal
E
Ignition module
www.bosch-home.com
'(
!
01
&
!:PPH616B21A
ULPG
12
Test point pressure (kPa)
Injectors marks
90
LHF
50
67
120
LHR
RHF
67
120
85
155
RHR
100
C
182
39.10
,56.
43.40
In compliance with AS/NZS 3100 and AS 4551:2008
Preinstalled NG
220-240V, 0.8A, 50Hz
MADE IN SPAIN
Distributed by BSH Home Appliances Pty Ltd
CIF: A-28-893550
ROBERT BOSCH HAUSGERÄTE GMBH
&
!:PPQ716B21A
www.bosch-home.com
CIF: A-28-893550
ROBERT BOSCH HAUSGERÄTE GMBH
GMK 10044
'(
!
01
ULPG
12
Test point pressure (kPa)
Injectors marks
LHF
67
120
67
120
LHR
RHF
50
90
91
160
RHR
26.50
,56.
28.60
In compliance with AS/NZS 3100 and AS 4551:2008
Preinstalled NG
220-240V, 0.6A, 50Hz
MADE IN SPAIN
Distributed by BSH Home Appliances Pty Ltd
GMK 10044
11
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
*9000567217*
9000567217
A