English
EN
DE
FR
ES
IT
取扱説明書
RU
ZH
JA
日本語
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manuale di istruzioni
Руководство пользователя
中文
Русский
Italiano
Español
Français
Deutsch
POWER AMPLIFIER
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
CAUT I ON
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
The above warning is located on the top of the unit.
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
8
9
10
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11
12
13
14
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When
a cart is used, use caution
when moving the cart/apparatus combination to avoid injury
from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det
brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
2 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your
use of this product in a residential environment will not result
in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in
all installations. If this product is found to be the source of
interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park,
Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Power Amplifier
Model Name : XMV8280/XMV8140/XMV8280-D/
XMV8140-D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including
interference that may cause undesired operation.
See user manual instructions if interference to radio reception
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
(class B)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance
with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be
connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or colored GREEN or
GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
(3 wires)
In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
In Norway: Apparatet må tilkoples jordet stikkontakt.
In Sweden: Apparaten skall anslutas till jordat uttag.
(class I hokuo)
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(Perchlorate)
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으
로 하며, 모든 지역에서 사용할 수 있습니다.
(class b korea)
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited
to, the following:
Power supply/power cord
Water warning
• Do not place the power cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy
objects on it, or place it in a position where anyone could walk on, trip over,
or roll anything over it.
• Only use the voltage specified as correct for the device. The required voltage
is printed on the name plate of the device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one you
purchased, the included power cord may not be compatible. Please check
with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock, damage to
the device(s), or even fire.
Do not open
• This device contains no user-serviceable parts. Do not open the device or
attempt to disassemble the internal parts or modify them in any way. If it
should appear to be malfunctioning, discontinue use immediately and have
it inspected by qualified Yamaha service personnel.
• Do not expose the device to rain, use it near water or in damp or wet
conditions, or place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as
water seeps into the device, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the device inspected by qualified
Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit. A burning item may
fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately turn off the power
switch and disconnect the electric plug from the outlet. Then have the device
inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or
damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/power cord
• When removing the electric plug from the device or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be used
for extended periods of time, or during electrical storms.
Location
• Do not place the device in an unstable position where it might accidentally
fall over.
• Do not block the vents. This device has ventilation holes at the front/rear/
sides to prevent the internal temperature from becoming too high. In
particular, do not place the device on its side or upside down. Inadequate
ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
• Do not use the device in a confined, poorly-ventilated location. If this device
is to be used in a small space other than an EIA-standard rack, make sure
that there is adequate space between the device and surrounding walls or
other devices: at least 10 cm at the sides, 10 cm behind and 40 cm above.
Inadequate ventilation can result in overheating, possibly causing damage to
the device(s), or even fire.
• Do not place the device in a location where it may come into contact with
corrosive gases or salt air. Doing so may result in malfunction.
PA_en_1
4 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
• Keep device away from the reach of children.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn
off the power switch and disconnect the plug from the outlet. Even when the
power switch is turned off, electricity is still flowing to the product at the
minimum level. When you are not using the product for a long time, make
sure to unplug the power cord from the wall AC outlet.
• If the device is mounted in an EIA standard rack, carefully read the section
“Precautions for Rack Mounting” on page 8. Inadequate ventilation can
result in overheating, possibly causing damage to the device(s),
malfunction, or even fire.
Connections
• Before connecting the device to other devices, turn off the power for all
devices. Before turning the power on or off for all devices, set all volume
levels to minimum.
• Use only speaker cables for connecting speakers to the speaker connectors.
Use of other types of cables may result in fire.
1/2
Maintenance
Backup battery
• Remove the power plug from the AC outlet when cleaning the device.
Handling caution
• Do not insert your fingers or hands in any gaps or openings on the device
(vents).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into
any gaps or openings on the device (vents) If this happens, turn off the
power immediately and unplug the power cord from the AC outlet. Then
have the device inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid
use excessive force on the buttons, switches or connectors.
• Do not use speakers for a long period of time at a high or uncomfortable
volume level, since this can cause permanent hearing loss. If you experience
any hearing loss or ringing in the ears, consult a physician.
• This device has a built-in backup battery. When you unplug the power cord
from the AC outlet, the internal data is retained. However, if the backup
battery fully discharges, this data will be lost. When the backup battery is
running low, the display indicates “012.” and the ALERT indicator is
flashing. In this case, immediately save the data to external device such as a
computer, then have qualified Yamaha service personnel replace the backup
battery.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
European Models
Inrush Current based on EN 55103-1:2009
13A (on initial switch-on)
5A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.
 Handling and maintenance
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device,
TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car
during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one
location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the
power until the condensation has completely dried out.
• Do not use this device for any purpose other than driving loudspeakers.
• When turning on the AC power in your audio system, always turn on tthe device LAST, to avoid speaker damage. When turning the
power off, the device should be turned off FIRST for the same reason.
 Saving data
This device has a built-in backup battery that maintains data in internal memory even when the device’s power is switched off. The
backup battery will eventually become depleted, however, and when that happens the contents of the internal memory will be lost.*
To prevent loss of data be sure to replace the backup battery before it becomes fully depleted. When the remaining capacity of the
backup battery becomes so low that it needs to be replaced a “012.” message will appear on the display during operation or when the
device is powered on. If either of these messages appears do not turn off the power and immediately transfer any data you want to save
to a computer or other external storage device, then have qualified Yamaha service personnel replace the backup battery. The average
life of the internal backup battery is approximately 5 years, depending on operating conditions.
* Data items maintained in the internal memory by the backup battery are as follows:
• Device parameters (Attenuator values, Polarity settings, HPF settings, Analog/digital input setting, and [SIGNAL] indicator display
setting).
• Event log.
Data items other than those described above are stored in memory that does not require backup power, and will be retained even if the
backup battery fails.
Information
 About this manual
• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your
device.
• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
PA_en_1
2/2
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
5
Contents
Introduction.....................................................................................................................7
Features.................................................................................................................................. 7
Included items......................................................................................................................... 7
Related Manuals and Software ............................................................................................... 7
Firmware Updates................................................................................................................... 8
About Dante ............................................................................................................................ 8
Precautions for Rack Mounting ............................................................................................... 8
Controls and Functions .................................................................................................9
Front Panel.............................................................................................................................. 9
Rear Panel ............................................................................................................................ 12
Connections and Setting Up .......................................................................................16
Setup for Analog Signal Input ............................................................................................... 16
[REMOTE] and [FAULT OUTPUT] Connectors ..................................................................... 21
Operations.....................................................................................................................23
Front Panel Operations ......................................................................................................... 23
Initializing the Internal Memory ............................................................................................. 25
Appendix .......................................................................................................................26
Troubleshooting..................................................................................................................... 26
Alert Numbers and Content .................................................................................................. 27
Dante Messages (XMV8280-D/XMV8140-D only) ................................................................ 29
High-impedance and Low-impedance Connections ............................................................. 30
Specifications .............................................................................................................234
General Specifications ........................................................................................................ 234
Block Diagram..................................................................................................................... 236
Dimensions ......................................................................................................................... 236
Current Draw and Heat Dissipation .................................................................................... 237
* The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous
improvements to the product, this manual may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately
sold accessories may not be the same in every locale, please check with your Yamaha dealer.
6 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Introduction
Thank you for your purchase of the Yamaha XMV8280, XMV8140, XMV8280-D or XMV8140-D power
amplifier. Please read through this manual carefully before beginning use, so that you will be able to take full
advantage of your power amplifier’s superlative features and enjoy trouble-free operation for years to come.
After you have read the manual, keep it in a safe place for reference when needed.
NOTE
• When there are differences in the specifications of the XMV8280/XMV8280-D and the XMV8140/XMV8140-D, this manual will
use curly brackets { } to enclose information that applies only to the XMV8140/XMV8140-D.
(Example: 280W {140W}).
• Unless otherwise specified, illustrations are taken from the XMV8280/XMV8280-D.
• For the remainder of this manual, the XMV8280, XMV8140, XMV8280-D and XMV8140-D are referred to as “XMV” collectively.
• In this book, the matrix processor MTX series units are reffered to as “MTX” collectively.
Features
The XMV is a multi-channel power amplifier with the following features.
• Both high-impedance and low-impedance connections are supported
Both high-impedance connections to 70V/100V lines and
4Ω/8Ω low-impedance connections are supported. A rear
panel DIP switch allows this setting to be specified for every
two channels.
• Newly-developed “Double Power mode”
The newly-developed “Double Power mode” doubles the
amplifier output of each channel when low-impedance connections are used.
* The number of available channels will be halved.
• Settings can be made via application software
Although settings such as mute on/off and attenuator values
can be edited from the panel of the amplifier itself, you can
use an MTX series matrix processor and computer to edit the
settings of multiple XMV units.
• Support for the newly-developed “YDIF” digital
audio transmission format
(XMV8280/XMV8140 only)
This allows up to 16 channels of audio and word clock to be
transmitted and received via an Ethernet cable.
This model can receive eight channels of audio signals via
YDIF.
• Dante network for large-scale systems
(XMV8280-D/XMV8140-D only)
This enables audio signal transfer over long-distance with
Dante equipped devices (such as the MTX5-D) with standard Ethernet cables.
• High efficiency
The newly-developed output circuits allows high efficiency.
Included items (please check)
•
•
•
•
•
Owner’s Manual
Power cord
Euroblock plugs (3-pin, 3.50mm pitch) x 2
Euroblock plugs with tabs (3-pin, 5.08mm pitch) x 8
Cable ties x 8
Related Manuals and Software
You can easily configure a complete sound system featuring the
XMV by connecting it to MTX series matrix processors or to
MTX Editor system configuration software. The owner’s manual for the MTX and for MTX Editor, and MTX Editor itself
(subsequently referred to as “the editor”) can be downloaded
from the download page of the following website.
http://www.yamahaproaudio.com/
• List of related manuals
MTX3 Owner’s
Manual
This explains how to use the MTX3
matrix processor.
MTX5-D Owner’s
Manual
This explains how to use the MTX5-D
matrix processor.
MTX Editor User’s
Manual
This explains how to use MTX Editor.
MTX Setup Manual
This explains how to use and set up
the matrix processor MTX series that
is used along with the XMV power
amp.
The “MTX Editor User’s Manual” and “MTX Setup Manual”
are electronic files in PDF format.
You can read the books on a computer. Use Adobe® Reader®
to read the books on screen, search for words very quickly, print
specific pages, or click links to display sections of special interest. The ability to search for words, or to follow links directly to
relevant sections in the document, are helpful attributes of this
electronic file format. We encourage you to take advantage of
these benefits.
You can download the latest Adobe Reader application from the
website listed below.
http://www.adobe.com/
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
7
Introduction
Firmware Updates
Use the MTX Editor to update the firmware of the XMV or
check the firmware version. For operation details, refer to the
“MTX Editor User’s Manual.”
You can download the latest firmware from the “Downloads”
page on the following website.
http://www.yamahaproaudio.com/
About Dante
The XMV8280-D/XMV8140-D units feature Dante technology
as a protocol to transmit audio signals. Dante is a network protocol developed by Audinate. It is designed to deliver multichannel audio signals at various sampling and bit rates, as well
as device control signals over a Giga-bit Ethernet (GbE) network. Dante also offers the following benefits:
• It transmits up to 512 in/512 out, for a total 1024 channels
(theoretically) of audio over a GbE network.
(The XMV8280-D/XMV8140-D features eight inputs with a
24/32-bit resolution.)
• Dante-enabled devices will automatically configure their
network interfaces and find each other on the network. You
can label Dante devices and their audio channels with names
that make sense to you.
• Dante uses high accuracy network synchronization standards
to achieve sample-accurate playback with extremely low
latency and jitter.
(Four types of latency are available on the XMV8280-D/
XMV8140-D: 0.25 msec, 0.5 msec, 1.0 msec, and 5.0 msec.)
• Dante supports redundant connections via primary and secondary circuits to defend against unforeseen difficulties.
• Connecting a Dante-enabled device to a computer over
Ethernet enables you to directly input or output audio signals
without using any audio interface devices.
Visit Audinate website for more details on Dante.
http://www.audinate.com/
More information on Dante is also posted on the Yamaha Pro
Audio website:
http://www.yamahaproaudio.com/
NOTE
Please do not use the EEE function (*) of network switches in a
Dante network.
Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly.
This may cause EEE to be enabled in Dante networks when it
is not appropriate, resulting in poor synchronization performance and occasional dropouts.
Therefore we strongly recommend that:
- If you use managed switches, ensure that they allow EEE to
be disabled. Make sure that EEE is disabled on all ports
used for real-time Dante traffic.
- If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE
operation cannot be disabled in these switches.
* EEE (Energy Efficient Ethernet) is a technology that reduces switch
power consumption during periods of low network traffic. It is also
known as Green Ethernet and IEEE802.3az.
8 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Precautions for Rack Mounting
This unit is rated for operation at ambient temperatures
ranging from 0 to 40 degrees Celsius. When mounting
the unit with other XMV unit(s) or other device(s) in an
EIA standard equipment rack, internal temperatures can
exceed the specified upper limit, resulting in impaired
performance or failure. When rack mounting the unit,
always observe the following requirements to avoid heat
buildup:
• When mounting the unit in a rack with devices such as
power amplifiers that generate a significant amount of
heat, leave more than 1U of space between the XMV
and other equipment. Also either leave the open
spaces uncovered or install appropriate ventilating panels to minimize the possibility of heat buildup.
• To ensure sufficient airflow, leave the rear of the rack
open and position it at least 10 centimeters from walls
or other surfaces. If the rear of the rack can’t be left
open, install a commercially available fan or similar
ventilating option to secure sufficient airflow. If you’ve
installed a fan kit, there may be cases in which closing
the rear of the rack will produce a greater cooling effect.
Refer to the rack and/or fan unit manual for details.
Controls and Functions
Front Panel
XMV8280/XMV8140
q
!8 r e w
y
i
t
!8
!1 !0
!2 !3
!6 !7
u o
XMV8280-D/XMV8140-D
q
!8 r e w
y
i
t
q Power switch
Turns power to the unit ON or OFF. Setting the switch to the
upward position turns the power on; the [POWER] indicator
!0 will light green. Setting the switch to the downward position turns the power off. If the switch is in the upward position and the [POWER] indicator is flashing, the unit is in
standby mode.
CAUTION
u o
!8
!1 !0
!4 !5
!6 !7
w [PROTECTION] A–H indicators
When the protection system is active, the indicator will light
orange. If the audio output is muted, turn off the power and
wait for the XMV to cool before turning the power on again.
The protection circuit will operate and the [PROTECTION]
indicator will light in the following situations.
 If the amplifier overheats and the output lim-
iter operates
• To ensure that high-volume noise is not output from
the speakers, power-on the equipment starting with
the audio sources, then the mixer and processors
(such as the MTX), and finally the amplifiers. Reverse
this order when turning the system off.
The speaker output will be attenuated if the heat sink of
the amplifier section exceeds 80°C, and will be muted if
the heat sink exceeds 90°C. The [PROTECTION] indicator will light at 80°C or higher.
• Rapidly turning the power switch ON and OFF in succession can cause the unit to malfunction. After turning the power switch OFF, wait for about 5 seconds
before turning it ON again.
 If the power supply overheats and shuts-down
The fan will rotate at high speed if the power supply section exceeds 90°C, and the analog circuits will shut down
if it exceeds 100°C.
The [PROTECTION] indicator will light at 100°C or
higher.
• If you modified parameter settings, do not turn the
power switch OFF for at least one second. Otherwise,
the changes to the settings may be lost.
• Even when the power switch is turned off, a small
amount of current is flowing through the unit. If you
plan not to use the unit for a long period of time,
remove the power cable from the AC outlet.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
9
Controls and Functions
 When overcurrent is detected
If for any reason the impedance falls below the specification for the mode, the speaker output is muted to prevent
overcurrent; muting will be cancelled after approximately
one second. If overcurrent is detected after muting is cancelled, the output will be muted again.
 If DC output is detected
The power supply section will be shut down.
 If excessive total current or maximum current
is detected
The output signal will be lowered.
When the limiter operates, the speaker output will be limited
and the indicator will light red. Lower the attenuator value so
that the limiter does not activate, referring to “Changing the
attenuator setting” (page 20). The limiter will operate in the
following situations.
• When an instantaneous input overload is detected
• When an input overload has been occurring for a specific
duration
• When the heat sink of the amplifier section exceeds the
allowable temperature
r [SIGNAL] A–H indicators
The [SIGNAL] indicator will light in green when the input/
output signal level exceeds a certain level.
This encoder is used to edit parameters. For details on the
available parameters, refer to “Front Panel Operations”
(page 23).
When the [PANEL LOCK] indicator !6 is lit in orange, front
panel operations are locked, and settings cannot be edited.
Defeat the lock if you want to perform these operations.
When you mute an output channel by operating the unit
itself or by operations via the [REMOTE] connector @7 or
the editor, the indicator of the corresponding channel will
light yellow.
o [MUTE] button
By holding down the [MUTE] button and pressing the
[SELECT] button t, you can switch muting on/off for the
channel selected by the [SELECT] button. When muting
turns on, the [MUTE] indicator i will light in yellow.
When the [PANEL LOCK] indicator !6 is lit, front panel
operations are locked, and channel mute operations are not
possible. Defeat the lock if you want to perform these operations.
Indicator
illumination status
!0 [POWER] indicator
input
-40dBFS or
more
!1 [ALERT] indicator
[YDIF] connectors @0
(XMV8280/XMV8140)
Dante [SECONDARY] connector @1
(XMV8280-D/XMV8140-D)
[SPEAKERS] output connectors @6
u Encoder
[SIGNAL]
indicators
used for (*1)
Analog input connectors @4
Dante [PRIMARY] connector
@1
This is a 3-digit 7-segment display that shows information
such as the attenuator value of the channel selected by the
[SELECT] button t or the alert number (page 27).
i [MUTE] A–H indicators
e [LIMIT] A–H indicators
Connector
y Display
output
*2
*1 For details on switching the indicator between input and
output, refer to “Front Panel Operations” (page 23).
*2 Depends on the condition. Refer to “[SIGNAL] Indicator Lit
Level” (page 235).
t [SELECT] A–H buttons/indicators
Use these buttons to select the output channel that you want
to control. The indicator of the selected channel will light in
green.
By using these in conjunction with the [FUNCTION] button
!7, you can change the parameter that is controlled by the
encoder. Refer to “Front Panel Operations” (page 23).
When the [PANEL LOCK] indicator !6 is lit, front panel
operations are locked, and output channel operations are not
possible. Defeat the lock if you want to perform these operations.
10 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
This will light in green when the power supply is turned on
by the power switch q.
It will flash when the unit is switched to standby mode via
the [REMOTE] connector or the editor.
This will flash or light when an abnormality occurs in the
unit.
If this is flashing, note the indication in the display and refer
to “Alert Numbers and Content” (page 27).
If it is lit, stop operating the unit. After a time, the indicator
will change to flashing, and an alert number will appear in
the display.
!2 [NETWORK] indicator (XMV8280/XMV8140 only)
This will light green if the XMV is in a linked state with an
external device via the network connector !9. It will flash
while data is being communicated.
!3 [YDIF] indicator (XMV8280/XMV8140 only)
This will light green when the [YDIF] connector @0 is connected normally and a valid word clock is being input.
Controls and Functions
!4 [PRIMARY]/[SECONDARY] indicators
(XMV8280-D/XMV8140-D only)
These show the communication status of the Dante [PRIMARY]/[SECONDARY] connectors @1. They flash rapidly
in green if the Ethernet cables are connected properly.
!5 [SYNC] Indicators
(XMV8280-D/XMV8140-D only)
These show the operating status of the Dante network. If the
green (upper) indicator lights, the unit is operating as a word
clock slave and synchronizing to the word clock. If the green
indicator flashes, the unit is operating as the word clock master. If the power to the unit is turned on but the green indicator is turned off, the unit is not functioning properly. In this
case, refer to the “Warning Messages” section (see page 29).
If the orange indicator lights or flashes, refer to the “Warning
Messages” section.
!6 [PANEL LOCK] indicator
This lights or flashes according to the state of the front panel
lock. To specify the front panel lock setting, use the Device
setup DIP switch @3.
Indicator
Lit
Status
Front panel operations are locked. Lock
will be temporarily defeated if you press
the [FUNCTION] button !7 and the
[SELECT] A button t.
Unlit
Front panel operations are not locked.
Flashing
Lock is temporarily defeated. When the
XMV is restarted, it will be in a locked
state.
!7 [FUNCTION] button
Use this to check or change the operating mode of the
XMV’s front panel. For details on how to perform front
panel operations, refer to “Front Panel Operations” (page
23).
!8 Cooling vent
Located behind the vent is a variable speed cooling fan that
draws air in from the front and exhausts it through the rear.
The fan speed will automatically vary according to the temperature.
Please be sure that you do not block the air intakes or
exhaust vents. You should also clean the air intakes and
exhaust vents regularly. If the air intakes are clogged with
dust or debris, the unit will overheat, which may result in the
unit shutting down.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
11
Controls and Functions
Rear Panel
XMV8280/XMV8140
@4
@5
@7 @8
@9
@7 @8
@9
ON
@2
ON
!9 @0
ON
1
2
3
4
5
6
7
8
@3
@4
@6
XMV8280-D/XMV8140-D
@4
@5
ON
@2
ON
@1
ON
1
@3
2
3
4
5
6
7
8
@4
!9 Network connector (XMV8280/XMV8140 only)
This is a 100BASE-TX Ethernet connector that allows the
unit to be connected to a computer via an Ethernet cable.
NOTE
• Use a CAT5e or better STP (Shielded Twisted Pair) cable
for the network connection to prevent electromagnetic
interference.
• When using MTX Editor to control the XMV, you must connect the MTX.
@6
@0 [YDIF] connectors (XMV8280/XMV8140 only)
These are RJ-45 connectors that allow the unit to be connected via an Ethernet cable to another YDIF-equipped
device so that audio signals and word clock signals can be
transmitted and received. Using a ring connection (YDIF
connection), you can connect to other devices equipped with
a [YDIF] connector. For details on settings for receiving
audio signals via the [YDIF] connector, refer to “Front Panel
Operations” (page 23).
Cables used for this connection should be 30 meters or less
between devices. Up to eight devices can be connected in a
network with YDIF connection.
For information on connections that use [YDIF] connectors,
refer to the “MTX Setup Manual.”
NOTE
To prevent electromagnetic interference, make connections
to the [YDIF] connector using a CAT5e or better STP
(Shielded Twisted Pair) cable in which all pins are connected with a straight connection.
12 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Controls and Functions
@1 Dante [PRIMARY]/[SECONDARY] connectors
(XMV8280-D/XMV8140-D only)
These are RJ-45 connectors that allow the unit to be connected to another Dante device such as the MTX5-D via an
Ethernet cable. The Dante [PRIMARY] connector can also
be used to connect to a computer via an Ethernet cable. To
connect, refer to the “MTX Editor User’s Manual.”
NOTE
• Use a CAT5e or better STP (Shielded Twisted Pair) cable
for the connection to the Dante [PRIMARY]/[SECONDARY] connectors to prevent electromagnetic interference.
Make sure that the metal parts of the plugs are electrically
connected to the STP cable shield by conductive tape or
comparable means.
• Connect only Dante-compatible devices or GbE-compatible devices (including a computer).
• Since Dante-compatible equipment made by Yamaha
such as the XMV8280-D/XMV8140-D contains a built’-in
network switch, the number of hops will be two or more.
For this reason, the 0.15 msec Latency setting in Dante
Controller will be grayed-out and unavailable.
@3 Device setup DIP switch
This DIP switch is used to make settings for the XMV. Refer
to the following for details on the settings.
NOTE
To change the switch settings, turn off the power to the unit.
If you change the settings while the power is on, the change
will not be effective until you turn the unit off and then on.
Refer to the following for details.
Switch
Status
Indicates the switch is in the upward position.
Indicates the switch is in the downward position.
XMV8280/XMV8140
1
2
3
4
5
6
7
8
4
5
6
7
8
@2 [UNIT ID] rotary switch
If multiple devices such as XMVs or MTXs are connected
on the same network, this rotary switch enables you to specify the UNIT ID that identifies each unit individually.
XMV8280/XMV8140
With the combination of the device setup DIP switches
1–3 @3 for upper digits and the rotary switch for lower digits, the UNIT ID can be specified in a maximum of 127
values, from “01” to “7F.”
XMV8280-D/XMV8140-D
1
2
3
XMV8280-D/XMV8140-D
With the rotary switch (HIGH) used for upper digits and
the rotary switch (LOW) for lower digits, the UNIT ID can
be specified in a maximum of 254 values, from “01” to
“FE.”
NOTE
• Do not use “00” or “FF” as the UNIT ID.
NOTE
• After you set the [UNIT ID] rotary switch, turn the power to
the unit off and then on.
Switch 1 and 2 are not used for the XMV8280-D/XMV8140D. Use the swiches in the factory set state (upward).
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
13
Controls and Functions
 Switch 1–3 (UNIT ID)
(XMV8280/XMV8140 only)
Use the DIP switches 1–3 to specify the upper digit, and
use the [UNIT ID] rotary switch @2 to specify the lower
digit to set a maximum of 127 combinations of UNIT ID
in the range of 01 through 7F (127).
DIP Switches
Setting
 Switch 4 (LED DIMMER)
This specifies the brightness of the front panel indicators
and display.
DIP Switches
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 1.
from 10 through 1F.
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 2.
from 20 through 2F.
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 3.
from 30 through 3F.
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 4.
from 40 through 4F.
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 5.
from 50 through 5F.
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 6.
from 60 through 6F.
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 7.
from 70 through 7F.
ON
Reduced brightness. Use
this setting if the indicators
and the display are too
bright.
The brightness of the [POWER] indicator !0 will not be
reduced.
 Switch 5 (PANEL LOCK)
This specifies the front panel lock setting (locks all panel
operations including the [MUTE] button o and attenuation adjustments). By selecting the LOCK setting after
you’ve completed all settings, you can prevent the volume or mute settings from being inadvertently changed.
Even if the LOCK setting is selected, you can temporarily
unlock the panel by pressing the [FUNCTION] button !7
and the [SELECT] A button t. The panel will be relocked when one minute has passed without any operation being performed, or when you once again press the
[FUNCTION] button and the [SELECT] A button, or
when you turn off the power.
DIP Switches
Setting
UNLOCK
LOCK
(XMV8280-D/XMV8140-D only)
Setting
Normal brightness.
NOTE
 Switch 3 (SECONDARY PORT)
This sets the Dante [SECONDARY] connector @1 on the
rear panel as to whether it will be used for daisy chain
connection or redundant. For details on the connection,
refer to the “MTX Editor User’s Manual.”
Description
The Dante [SECONDARY] connector is used
for a daisy chain connection. A signal at the
DAISY CHAIN
Dante [PRIMARY] connector will be transmitted to the next device in
the chain as is.
The Dante [SECONDARY] connector is used
for a redundant network.
It will function as backup
REDUNDANT
connection, independent
of the network to which
the Dante [PRIMARY]
connector is connected.
Description
OFF
Description
The UNIT ID’s The setting range of the
upper digit is [UNIT ID] rotary switch is
set to 0.
from 01 through 0F.
DIP Switches
Setting
Description
The front panel will not be
locked.
Front panel operations
other than the power will be
locked.
 Switch 6 (IP SETTING)
This selects whether the UNIT ID value will be used as
the IP address for the unit to communicate with a computer, or whether the IP address will be assigned by the
editor or the DHCP server.
DIP Switches
Setting
Description
UNIT ID
The IP address will be
specified using the UNIT ID
value.
The IP address will be
192.168.0.xxx (xxx is the
UNIT ID value).
However, if the UNIT ID is
“FF,” xxx is 127.
PC
The IP address will be
specified by the editor or
the DHCP server.
NOTE
Set this to the “UNIT ID” position the first time you connect this device to a computer after purchase. After
specifying the IP address from MTX Editor, change this
switch to the “PC” position.
14 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Controls and Functions
 Switches 7 and 8 (START UP MODE)
These specify the startup mode.
DIP Switches
Setting
RESUME
Description
The unit will start up normally.
The internal memory will be
initialized. For details on the
INITIALIZE memory that will be initialized, refer to “Initializing the
Internal Memory” (page 25).
@4 Analog input connectors
These are Euroblock 3-pin analog audio input connectors.
For details on settings for receiving audio signals via the
analog input connectors, refer to “Front Panel Operations”
(page 23).
For details on how to attach Euroblock connectors, refer to
the “Connections and Setting Up” section entitled “Connecting the Analog Inputs (Euroblock)” (page 16).
 Impedance (switches 3 and 7)
When using a low impedance connection, set these as
appropriate for the impedance of the speakers that are
connected. Check the specifications of the speakers.
For example if two 8Ω speakers are connected in parallel,
the total impedance will be 4Ω.
 Double Power mode (switches 4 and 8)
When a low impedance connection is used, these
switches specify the output of the amplifier. If the 280W
{140W} setting is selected, input/output is enabled for
both channels. If the 560W {280W} setting is selected,
the output from the amplifier will be doubled, but input/
output will be disabled for channels B, D, F and H.
 70V/100V (switches 2 and 6)
When a high impedance connection is used, these
switches specify the maximum output voltage (Vrms) of
the amplifier.
@6 [SPEAKERS] output connectors
@5 [SPEAKERS] DIP switches
This DIP switch makes settings for the XMV’s amplifier in
groups of two channels.
The left set of switches 1 through 4 specify the output setting
for channels G and H, and switches 5 through 8 specify the
output setting for channels E and F. The right switches 1
through 4 specify the output setting for channels C and D,
and switches 5 through 8 specify the output setting for channels A and B.
These are barrier strip type speaker output connectors. For
details on how to make connections to a barrier strip, refer to
the “Connections and Setting Up” section entitled “Connecting Speaker Cables” (page 18).
@7 [REMOTE] connector
This is a Euroblock 3-pin connector that allows muting/
unmuting of all channels and power-on/standby to be controlled remotely. For details, refer to “[REMOTE] and
[FAULT OUTPUT] Connectors” (page 21).
@8 [FAULT OUTPUT] connector
Use these switches to make the following settings.
Description
Switches 1–4
Switches 5–8
280W{140W}, 8Ω
Low-impedance
Connection
560W{280W}*, 8Ω
280W{140W}, 4Ω
560W{280W}*, 4Ω
High-impedance
Connection
70V, 250W{125W}
100V, 250W{125W}
* If this setting is chosen, input/output will be disabled for
channels B, D, F and H.
This is a Euroblock 3-pin connector that allows an external
device to be notified when a fatal malfunction occurs in this
unit. NC and C will be shorted when the amplifier is operating normally; NO and C will be shorted when a problem
occurs (page 21).
If a problem occurs, the [PROTECTION] indicator w will
light in orange.
@9 [AC IN] connector
Connect the supplied AC power cord here. First connect the
AC power cord to the connector on the rear panel of this unit,
then plug it into an appropriate AC power outlet.
CAUTION
Before connecting or disconnecting the power cord,
make sure that the power to the unit is turned OFF.
 Low impedance connection / high impedance
connection (switches 1 and 5)
These select either a low impedance connection or a high
impedance connection. Set them as appropriate for the
connected speakers and the way in which the speakers are
connected. For details on connections, refer to “Highimpedance and Low-impedance Connections” (page 30).
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
15
Connections and Setting Up
 Connecting the Analog Inputs (Euroblock)
Setup for Analog Signal Input
This chapter explains how to set up the XMV to input analog
signals.
If you are using the XMV along with the MTX, refer to the
“MTX Setup Manual.” Refer to this manual for details regarding the following items, even if you are using the XMV along
with the MTX.
• Making settings for speaker output
• Connecting the speaker output connectors
• Making high pass filter (HPF) settings
• Lowering the brightness of the indicators and the display
• Locking the panel
Here we will make and verify the input/output settings as outlined below.
Explanation
Page
Rack-mounting the Unit
16
Checking the Device Setup DIP Switch Settings
16
Connecting the Analog Inputs (Euroblock)
16
Making Settings for Speaker Output
17
Connecting Speaker Cables
18
Connecting the Power Cord
18
Turning the Power On
19
Enabling Analog Input
19
Making High Pass Filter (HPF) Settings
19
Checking the Wiring
20
Lowering the Brightness of the Indicators and the
Display
20
Locking the Front Panel
20
CAUTION
Steps earlier than “Turning the Power On” must be performed with the power off. If you perform these steps with
the power on, the settings might not be applied, or you
might be subject to electrical shock if you touch the connectors.
 Rack-mounting the Unit
Refer to “Precautions for Rack Mounting” (page 8), and
mount the XMV in your rack.
 Checking the Device Setup DIP Switch Settings
Make sure that all of the rear panel’s device setup DIP
switches (page 13) are in the upward position.
1
2
3
4
5
6
7
8
16 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Connect the analog outputs of your mixer or other device to
the analog input connectors (page 15).
You must use the supplied Euroblock plugs with tabs.
If these have been lost, please contact your Yamaha dealer.
Cable preparation
approx.
7 mm
approx.20 mm
• To prepare the cable for attachment to a Euroblock
connector, strip the wire as shown in the illustration
using stranded wire to make connections. With a
Euroblock connection, stranded wires may be prone
to breakage because of metal fatigue due to the
weight of the cable or due to vibration. Bundle the
cables and the Euroblock tabs using the supplied
cable ties (page 17). When rackmounting your
equipment, use a lacing bar when possible to bundle and fasten the cables.
NOTE
Do not tin (plate with solder) the exposed end.
• If cables will be frequently connected and disconnected, as in the case of a portable installation, we
recommend that you use ferrules with insulation
sleeves. Use a ferrule whose conductor portion has
an external diameter of 1.6 mm or less, and a length
of approximately 7 mm (such as the AI0,5-6WH
made by the Phoenix Contact corporation).
1.6 mm or less
approx.
7 mm
Connections and Setting Up
 Making Settings for Speaker Output
1. Loosen terminal screws.
Loosen.
Slotted screwdriver
Use the rear panel [SPEAKERS] DIP switches to make the
appropriate settings for the XMV’s speaker output.
The method of connection will differ depending on whether
you’re using a low impedance connection or a high impedance connection.
Terminal screw
Low-impedance connection
Euroblock plug
8Ω/4Ω
Tab
NOTE
High-impedance connection
A slotted screwdriver with a blade width of about 3 millimeters is recommended.
3 mm or less
Speaker transformer
70V/100V
10W
10W
10W
10W
10W
2. Insert cables.
+ –
G
For details, refer to “High-impedance and Low-impedance
Connections” (page 30).
The explanation of the settings is divided into the following
sections.
3. Securely tighten terminal screws.
Pull the cables (not too strongly) to confirm that they are
securely connected.
4. Bundle the cables and the Euroblock tab
using the supplied cable tie.
 When using low impedance connections (page
17)
 When using low impedance connections with
Double Power mode (page 18)
 When using high impedance connections
(page 18)
Since these settings can be made independently for channels
A/B, channels C/D, channels E/F and channels G/H, you can
use more than one of the above methods
 When using low impedance connections
Depending on the impedance (4Ω or 8Ω) of the connected
speakers, set the [SPEAKERS] DIP switches as follows.
Setting
Switches 1–4
Switches 5–8
280W{140W}, 8Ω
NOTE
Trim any excess part of the cable tie as necessary.
5. Insert the Euroblock plug into the Analog
input connector of the device.
280W{140W}, 4Ω
NOTE
If you make settings for low impedance connections, the
HPF will automatically be turned OFF.
The XMV features a switch function between 8Ω and 4Ω to
guarantee the output in case it is connected to a speaker with
an impedance of 8Ω or higher.
If you connect a speaker with an impedance of 8Ω or higher,
set the [SPEAKERS] DIP switches to 8Ω. If you connect a
speaker with an impedance of 4Ω or higher, but lower than
8Ω, set the [SPEAKERS] DIP switches to 4Ω.
Total impedance(x)
4Ω
x
8Ω
x
8Ω
Setting
4Ω
8Ω
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
17
Connections and Setting Up
Double Power mode
If you use Double Power mode, input/output will be disabled for channels B, D, F and H.
Depending on the impedance (4Ω or 8Ω) of the connected
speakers, set the [SPEAKERS] DIP switches as follows.
Setting
Switches 1–4
Switches 5–8
560W{280W}, 8Ω
 If using a bare conductor
Wrap the conductor around the barrier strip terminal as
shown below, and tighten the screw. Be sure that the bare
wire does not touch the chassis.
15mm*
 When using low impedance connections with
560W{280W}, 4Ω
NOTE
If you make settings for low impedance connections, the
HPF will automatically be turned OFF.
Wire should
not touch
the chassis.
* Actual size
Speaker cable
 When using high impedance connections
Depending on the specifications (70V or 100V) of the
system in which this unit is being installed, set the
[SPEAKERS] DIP switches as follows.
Setting
Switches 1–4
Switches 5–8
70V
100V
NOTE
If you make settings for high impedance connections,
the HPF will automatically be set to 80 Hz.
 Connecting Speaker Cables
The [SPEAKERS] output connectors (page 15) on the rear
panel are barrier strip type connectors. We will explain connections using a spade lug and connections using a bare conductor.
CAUTION
Make sure that the power is turned off. If the power is
on, you risk electrical shock.
 If using a spade lug
From below, insert the spade lug all the way, and tighten
the screw.
<=0.31"
(<= 7.8mm)
=>0.15"
(=>3.7mm)
18 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
NOTE
• If the [SPEAKERS] DIP switches (page 15) are in Double Power mode (switch 4 or 8 is in the lowered position), audio will not be output from the corresponding
channel (channel B, D, F or H).
• Ensure that tension is not applied to the speaker cable.
• Connect the cables so that the amplifier’s “+” and “-”
symbols match those of the speaker. If they are
reversed, the polarity will be reversed.
TIPS
Since a large amount of current can flow in a speaker
cable, a magnetic field will be generated. If sensitive circuits such as a microphone input cable or a microphone
amp are located near a speaker cable, electromagnetic
induction may produce noise in the input cable or circuit.
Input cables and devices that contain sensitive circuits
should be kept at a distance from speaker cables; we
also recommend that you fasten the cables in place.
 Connecting the Power Cord
Connect the included power cord to the [AC IN] connector
(page 15) on the rear panel. First connect the AC power cord
to the connector on this unit, then plug it into an appropriate
AC power outlet.
CAUTION
You must turn off the power before connecting the
power cord.
Connections and Setting Up
 Turning the Power On
Use the front panel power switch (page 9) to turn the power
on.
CAUTION
Before you turn the power on, make sure that audio
signals are not being input to the analog input connectors. If audio signals are being input, excessive input
will be applied to the speakers when the power is
turned on, possibly damaging the speaker system or
damaging your hearing by high-volume sound. If there
is a problem with the speakers or the wiring, the protection circuit will operate immediately when the power
is turned on. Check whether there might be a problem
with the wiring.
 Enabling Analog Input
Using the front panel, enable analog input as follows.
1. While holding down the [FUNCTION] button, turn the encoder to make the display
indicate “SRC.”
The control mode will change to “Analog/digital input
selection.”
2. Take your finger off the [FUNCTION] button,
and turn the encoder to make the display
indicate “ANA.”
Input from the analog input connectors will be enabled.
NOTE
If a certain period of time elapses without any operation
being performed, the unit will return to Attenuation setting operating mode.
 Making High Pass Filter (HPF) Settings
If the unit is set for low impedance connections, the HPF
will be OFF. If the unit is set for high impedance connections, the 80 Hz HPF will be enabled.
If you want to change this setting, proceed as follows.
1. While holding down the [FUNCTION] button, turn the encoder to make the display
indicate “HPF.”
The control mode will change to “HPF.”
2. Press the [SELECT] button of the channel
for which you want to make HPF settings.
The [SELECT] indicator of the channel whose HPF you
are setting will light.
3. Turn the encoder to select the desired HPF
setting.
The available HPF settings are OFF / 40 Hz / 80 Hz.
NOTE
• In order to protect the amplifier, the HPF cannot be turned
OFF if high impedance connections are used.
• If you’re using a sub-woofer with high-impedance connections, we recommend that you change the HPF setting to
40 Hz.
• If you’re using a full-range speaker with high-impedance
connections, the amplifier’s protection circuit may operate
if the HPF is set to other than 80 Hz. We recommend that
you use the 80 Hz setting.
• If a certain period of time elapses without any operation
being performed, the unit will be placed in Attenuation setting operating mode.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
19
Connections and Setting Up
 Checking the Wiring
Here we’ll explain how to change the attenuation settings
and switch muting on/off, which you will need to do when
checking the wiring.
Before you check the wiring, we recommend that you set the
attenuator of all channels to the lowest setting (-99 dB) to
prevent speaker damage.
To check the wiring, you’ll need to be outputting an audio
signal from the mixer or other device that’s connected to the
analog input connectors.
NOTE
If the speakers are remotely located and you are unable to
check the signal output easily, changing the [SIGNAL] indicator (page 10) setting to “output” will allow you to check
whether current is flowing to the speakers. For details on
switching the indicator setting, refer to “Front Panel Operations” (page 23).
 Changing the attenuator setting
Here’s how to change the attenuator setting.
1. While holding down the [FUNCTION] button, turn the encoder to make the display
indicate “ATT.”
2. Press the [SELECT] button of the channel
whose setting you want to adjust.
The [SELECT] indicator of the selected channel will
light.
3. Turn the encoder to gradually raise the
attenuator setting from -99, and verify
that sound is produced from the speaker.
 Switching the mute setting on/off
While holding down the [MUTE] button,
press the [SELECT] button of the channel
that you want to control.
When mute is on, the [MUTE] indicator will light; when
mute is off, the [MUTE] indicator will be unlit.
 Lowering the Brightness of the Indicators
and the Display
If the front panel LED indicators are too bright, you can
lower their brightness.
After turning the power off, set the rear panel device setup
DIP switch 4 (LED DIMMER) to the lower position (ON).
The next time you turn the power on, the unit will start up
with decreased indicator brightness.
NOTE
The brightness of the [POWER] indicator will not be
reduced.
20 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
 Locking the Front Panel
By locking the panel you can disable front panel operations
other than controlling the power (front panel lock).
When this unit is used as part of an installed system, you can
lock down the settings by disabling operations from the front
panel, thus preventing inadvertent changes.
After turning the power off, set the rear panel device setup
DIP switch 5 (PANEL LOCK) to the lower position
(LOCK). The next time you turn the power on, the unit will
start up with the front panel locked.
Even in the locked state, you can temporarily defeat the
panel lock by pressing the [FUNCTION] button and the
[SELECT] A button. However, it will be re-locked when any
of the following conditions occur.
• One minutes elapses without any operation being performed after the panel is temporarily unlocked
• You press the [FUNCTION] button and the [SELECT] A
button
• You turn the power off
The lock status is shown by the front panel [PANEL LOCK]
indicator.
• Locked: lit
• Not locked: unlit
• Temporarily unlocked: flashing
Connections and Setting Up
[REMOTE] and [FAULT OUTPUT] Connectors
This chapter explains how to use and connect the [REMOTE]
connector and [FAULT OUTPUT] connector located on the rear
panel of the XMV.
 Using the [FAULT OUTPUT] Connector
(Euroblock 3-pin)
A lamp or other indicator can be connected to the rear panel
[FAULT OUTPUT] connector to inform an operator when a
problem occurs.
 Using the [REMOTE] Connector
(Euroblock 3-pin)
You can connect switches to the rear panel [REMOTE] connector (page 15), and use them to remotely mute/unmute all channels or switch the power standby/on status.
From the left, the [REMOTE] connector consists of MUTE
ALL, STANDBY, and GND pins.
The [REMOTE] connector uses a Euroblock plug.
For details on how to connect Euroblock plugs, refer to “Connecting the [REMOTE] Connector or [FAULT OUTPUT] Connector” (page 22).
The [FAULT OUTPUT] connector (page 15) consists of NO
(Normally Open), C (Common), and NC (Normally Closed)
pins. The [FAULT OUTPUT] connector is a relay circuit that
operates as follows.
Normal state
Fault condition
Power off
NO
Open
Closed
Closed
NC
Closed
Open
Open
• Muting/unmuting all channels
Turning mute on
Turning mute off
The [FAULT OUTPUT] connector uses a Euroblock plug. For
details on how to connect Euroblock plugs, refer to “Connecting
the [REMOTE] Connector or [FAULT OUTPUT] Connector”
(page 22).
Example: Using an LED to indicate the
XMV’s normal/fault status
 Normal state
XMV
NOTE
When all channels are muted via the [REMOTE] connector,
the [MUTE] button on the front panel cannot be operated.
NC
Lit
C
NO
Unlit
• Switching the power standby/on status
Switching the power to
standby
Turning the power on
 Shut-down state
XMV
NC
Unlit
C
NO
Lit
NOTE
When the power is set to standby via the [REMOTE] connector, turning on the power switch will place the unit in
standby mode.
CAUTION
The rated load of the relay contacts is 1A, DC 30 V for a
resistive load.
Do not apply a load that exceeds this rating.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
21
Connections and Setting Up
 Connecting the [REMOTE] Connector or
2. Insert cables.
[FAULT OUTPUT] Connector
You must use the supplied Euroblock plugs when making connections to the [REMOTE] connector or [FAULT OUTPUT]
connector.
If these have been lost, please contact your Yamaha dealer.
Cable preparation
3. Securely tighten terminal screws.
approx.
5 mm
Pull the cables (not too strongly) to confirm that they are
securely connected.
• To prepare the cable for attachment to a Euroblock
connector, strip the wire as shown in the illustration
using stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to
breakage because of metal fatigue due to the weight of
the cable or due to vibration.
NOTE
Do not tin (plate with solder) the exposed end.
• If cables will be frequently connected and disconnected, as in the case of a portable installation, we
recommend that you use ferrules with insulation
sleeves. Use a ferrule whose conductor portion has an
external diameter of 1.3 mm or less, and a length of
approximately 5 mm (such as the AI0,5-6WH made by
the Phoenix Contact corporation).
1.3 mm or less
approx.
5 mm
1. Loosen terminal screws.
Slotted screwdriver
Loosen.
Euroblock plug
Terminal
screw
NOTE
A slotted screwdriver with a blade width of about 3 millimeters is recommended.
3 mm or less
22 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
4. Insert the Euroblock plug into the [REMOTE]
connector or [FAULT OUTPUT] connector of
the device.
Operations
Front Panel Operations
This chapter describes the operations you can perform from the
front panel.
NOTE
If you modify the parameter settings, do not turn the power
switch OFF for at least one second. Otherwise, the changes to
the settings may be lost.
 Basic Operations
To do this...
Operation
Description
While you hold down the [FUNCTION] button, the current operating mode will be shown in the display. The modes are indicated as follows.
Indication
Checking the current operating mode
[FUNCTION]
Operating mode
ATT
Attenuation setting
POL
Polarity setting
HPF
Turn the high pass filter on/off and
change the cutoff frequency
SRC
Analog/digital input selection
SIG
[SIGNAL] indicator display selection
DIS
Digital input sensitivity selection
Changing the operating mode
[FUNCTION] + encoder *1
Use the encoder to change the operating mode.
When you release the [FUNCTION] button, the operating mode
shown at that time will be selected; the display will show the
parameter value.
If a certain period of time elapses without any operation being
performed, the operating mode will be switched back to “Attenuation setting.”
Turning Mute on/off
[MUTE] + [SELECT] (of the channel to be muted) *1
When muting turns on, the [MUTE] indicator of the selected
channel will lit.
When muting turns off, the [MUTE] indicator will go unlit.
[FUNCTION] + [SELECT] A *1
When front panel lock is temporarily disabled, the [PANEL
LOCK] indicator will flash.
When front panel lock is enabled, the [PANEL LOCK] indicator
will lit. While the front panel is locked, “LC” is shown in the display.
Even if front panel lock is temporarily disabled, it will be
relocked when one minute passes without any operation being
performed or when the power is turned off.
Temporarily disabling or reenabling front panel lock
*1: “X+Y” means “operate Y while operating X.” For example, “[SELECT] A + encoder” means that you should hold down the [SELECT] A
button and operate the encoder.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
23
Operations
 Parameter Operations
To do this...
Changing the attenuator
value (volume)
Operating mode
(indication)
attenuator
(ATT)
Operation
[SELECT] (of the channel to
be changed)  encoder *2
Description
The [SELECT] indicator of the selected channel
will lit, and the attenuator value can be edited by
the encoder.
The range of adjustment is -99 dB–0 dB in 1 dB
steps.
The [SELECT] indicator of the selected channel
will light, and the polarity can be changed by using
the encoder.
Changing the polarity
Changing the high pass filter (HPF) cutoff frequency
Turning off the high pass
filter (HPF)
polarity
(POL)
[SELECT] (of the channel to
be changed)  encoder *2
Indication
Polarity
NOR
Normal polarity
INV
Inverted polarity
The [SELECT] indicator of the selected channel
will light, and the high pass filter (HPF) on/off setting and cutoff frequency can be changed by using
the encoder. This will be set to 80 Hz if a high
impedance connection is specified; it will be turned
OFF if a low impedance connection is specified.
HPF
(HPF)
[SELECT] (of the channel to
be changed)  encoder *2
Indication
Meaning
OFF
HPF is off
H40
Cutoff frequency is 40 Hz
H80
Cutoff frequency is 80 Hz
In order to protect the amplifier, the HPF of the
selected channel cannot be turned OFF if a high
impedance connection is specified.
Use the encoder to change the analog/digital input
selection. This selection applies to all channels.
Indication
ANA
Input connectors
Analog input connectors
[YDIF] connectors
(XMV8280/XMV8140)
Switching between analog/
digital input
analog/digital input
selection
(SRC)
DIG
Encoder operation
Dante [PRIMARY]/
[SECONDARY] connectors
(XMV8280-D/XMV8140-D)
Do not select “analog” if your audio network has
been configured using the [YDIF] connectors or
Dante [PRIMARY]/[SECONDARY] connectors.
Selecting “analog” will interrupt audio transmission
to and from the devices that are connected via the
YDIF connectors or Dante connectors.
Switching whether the
[SIGNAL] indicators are
used for input or for output
[SIGNAL] indicator
switching
(SIG)
Use the encoder to specify whether the [SIGNAL]
indicators will show the input signal level or the output signal level.
Encoder operation
Indication
IN
OUT
Digital input sensitivity
selection
digital input
sensitivity
(DIS)
Lit condition
Input
Output
Use the encoder to change the digital input sensitivity setting. To prevent inadvertent setting, the
value does not change right away when the
encoder is turned. Until the input sensitivity
changes, “– – – ” appears in the display.
Encoder operation
Indication
Input sensitivity
D20
0 dB
D03
+17 dB
–––
(value in process of being
changed)
*2: “XY” means “operate X, and then operating Y.” For example, “[SELECT] A  encoder” means that you should press the [SELECT]
A, and then operate the encoder.
24 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Operations
Initializing the Internal Memory
Execute the following procedure when you return the internal
memory settings to their factory set state (initialize the internal
memory), such as when the amplifier has been moved to a different location.
1. Turn off the power.
2. Set device setup DIP switch 7 to the downward position and switch 8 to the upward
position.
6. Turn on the power.
The following parameters held in memory are initialized.
•
•
•
•
•
•
Attenuator values
Polarity settings
HPF settings
Analog/digital input setting
[SIGNAL] indicator display setting
Event log
* When the unit is shipped from the factory, the device setup
DIP switches are all in the upward position.
3. Turn on the power. The initializing operation
will start.
• In the case of the XMV8280/XMV8140
During initialization, the [NETWORK], [YDIF], and
[PANEL LOCK] indicators will flash. When initialization
is complete, the [NETWORK] and [YDIF] indicators will
flash.
• In the case of the XMV8280-D/XMV8140-D
During initialization, the [PRIMARY], [SECONDARY],
[SYNC] (green), [SYNC] (orange) and [PANEL LOCK]
indicators will flash. When initialization is complete, the
[PRIMARY], [SECONDARY] and [SYNC] (green) indicators will flash.
If the unit fails to initialize, the [POWER] indicator will
light, the [ALERT] indicator will flash, and other indicators will turn off. Please contact your Yamaha dealer.
4. Make sure the initializing operation is complete and turn off the power.
5. Set device setup DIP switches 7 and 8 to the
upward position (RESUME).
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
25
Appendix
Troubleshooting
Symptom
The power won’t turn on
Possible causes
The power cord is disconnected
Connect the power cord.
The analog/digital input setting is
incorrect
From the front panel, check the analog/digital
input setting.
Double Power mode is selected
In Double Power mode, no audio signals will be
output from channel B, D, F or H. Either turn off
Double Power mode, or re-connect the cables.
An input/output cable is disconnected
Connect the input/output cables. Also, make sure
that the cables are securely connected.
The mute function is turned on
Make sure that the [MUTE] indicator is unlit. If it is
lit, turn Mute off.
The attenuator value is too low
Change to “Attenuation setting” (page 23), and
check whether the attenuator value is appropriate
on the display (page 10).
No audio signal is being input
Make sure that an audio signal is being output
from the mixer or other device that is outputting
audio to the XMV.
The protection circuit has operated
(the [PROTECTION] indicator is lit)
Turn off the power, wait for the XMV to cool, and
then turn the power on again.
The unit is in standby mode
(the [POWER] indicator is flashing)
Make sure that the switch connected to the
[REMOTE] connector is turned on. Alternatively,
use the editor to check that this is turned on.
Some abnormality has occurred at
digital input from the MTX
(on XMV8280/XMV8140: [YDIF]
indicator is unlit; on XMV8280-D/
XMV8140-D: green [SYNC] indicator is unlit)
Check the MTX. For details, refer to MTX manuals.
“Analog” input has been selected on
a device that is connected via a
YDIF connector
(XMV8280/XMV8140 only)
Select “digital” input on the device. If you wish to
use the device for analog input, disconnect the
device from the YDIF network.
The device has failed
The device has failed. Contact your Yamaha
dealer for repair.
No sound is heard
The [ALERT] indicator remains
flashing or lit even after you’ve
turned the power on/off
Possible solution
* If taking the above steps does not solve the problem, contact your Yamaha dealer for repair.
The Yamaha Pro Audio website provides a FAQ (a list of frequently asked questions, with answers).
http://www.yamahaproaudio.com/
26 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Appendix
Alert Numbers and Content
If a problem occurs in the XMV, the [ALERT] indicator will flash and an alert number will appear in the display.
The alert numbers, the corresponding content, and the appropriate actions are listed below.
Alert number
No display
(only [ALERT] is lit)
Meaning
Response
Turn the power off, then turn on after waiting at least 5
seconds. If this does not solve the problem, please initialize the memory. Should this also fails, contact your
Yamaha dealer.
The device has not started up correctly.
001.–008.
010.
The internal backup battery has been completely
exhausted or is not installed.
011.
The internal backup battery has run extremely low, and
it is possible that the internal memory has been cleared.
012.
The internal backup battery has only a small amount of
power remaining.
This does not affect the operation of the device. However, if you continue using the device, the settings may
be lost and reset to the default values. Contact your
Yamaha dealer as soon as possible.
013.
A problem has occurred with the internal clock, and it
has been initialized (January 1, 2000, 0:00)
If this occurs each time you turn on the power, it is possible that the internal backup battery has run down or that
the device has malfunctioned. Contact your Yamaha
dealer.
If this occurs only once, an abnormality was detected
with the clock setting and it was initialized; use MTX Editor to set the time.
015.
The settings saved in internal memory have been lost.
Either the internal backup battery has run low, or the
device has malfunctioned. Contact your Yamaha dealer.
016.
A memory problem has occurred.
Contact your Yamaha dealer.
021.
The word clock master has become unlocked.
Make sure that the word clock signal is being input correctly.
022.
The digital signal being input to the [YDIF IN] connector
is not synchronized to the word clock of this device.
023.
The digital signal being input to the [YDIF IN] connector
is not continuously synchronized to the word clock of
this device.
030.
There is a problem with the connection of the [YDIF IN]
connector.
Make sure that YDIF cables are properly connected.
Use cables that meet the required specifications.
040.
Duplicate IP addresses.
Change the IP addresses so that there are no duplicates.
041.
IP address was not set within 60 seconds of startup.
Please check rear panel DIP switch 6 (IP Setting). If DIP
switch 6 is set to “PC,” use MTX Editor or DHCP server
to specify the device IP address.
043.
Too many devices are connected to the network.
Reduce the number of devices connected to the network.
050.
The UNIT ID is set to “00.”
Set the UNIT ID to something other than “00.”
051.
Devices with identical UNIT IDs were found connected
within the same network.
Change the UNIT ID so that there are no duplicates.
100.
The power supply was shut down because d.c. was
detected on a speaker output.
It is likely that the device has malfunctioned; immediately
stop using the device and contact your Yamaha dealer.
The power supply was shut down because its temperature exceeded the allowed limit.
Turn the power off, let the power supply cool down, then
turn the power on again.
Continuous high-power output will cause high temperatures, so please lower the output level. If the temperature
is still high, check whether dirt or a foreign object could
have clogged the cooling fan, and clean the fan if necessary.
101.
When you turn off the power, the current settings will be
lost, and will return to the default values. Please stop use
immediately, and contact your Yamaha dealer.
Make sure that YDIF cables are properly connected.
Use cables that meet the required specifications.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
27
Appendix
Alert number
Meaning
103.
Protection has been activated, and the power supply
was shut down.
104.
Protection has been activated, and muted.
105.
A short circuit was detected in the speaker output connector, so the output signal has been muted.
The temperature of the amp section (heat sink) has
changed, and the speaker output is now ****.
106.
110.
**** = 0dB and OK
-1dB and in protection
muted and in protection
The Redundant Backup function has been activated,
and the input signal has been switched.
28 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Response
Continuous high-power output may have activated protection; lower the output level.
For details on the reason that protection was activated,
refer to “[PROTECTION] A–H indicators” (page 9).
It may be that the speaker output connector’s “+” and “-”
are shorted, or that the connected speaker has malfunctioned.
Continuous high-power output will cause high temperatures, so please lower the input level or attenuator. If the
temperature is still high, check whether dirt or a foreign
object could have clogged the cooling fan’s air intake,
and clean it if necessary.
There is a problem in the digital signal being input to the
digital signal port.
Appendix
Dante Messages (XMV8280-D/XMV8140-D only)
Warnings and certain other types of information are displayed via the XMV8280-D/XMV8140-D front panel indicators.
Messages are also displayed in the Dante Controller Error Status field.
Each indicator lights or flashes as described below:
The indicator is off.
Unlit
Lit
The indicator remains lit steadily.
Flash
The indicator continues to flash.
Flash x 2
The indicator flashes twice cyclically.
 Information Messages
The status is shown by the lit/flashing state of the indicator.
If the orange [SYNC] indicator is unlit, the unit is operating normally.
If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.
SYNC Indicators
Description
Explanation
Synchronization is occurring.
Please wait until the unit synchronizes
completely. It may take approximately 60
seconds for synchronization to be completed.
The unit is functioning correctly as the word clock
master.
The unit is operating as the word clock
master.
The unit is functioning correctly as the word clock
slave.
The unit is operating as the clock slave
and the clock is synchronized.
(green) Unlit
(orange) Lit
(green) Flash
(orange) Unlit
(green) Lit
(orange) Unlit
 Warning Messages
The indicator will remain lit or continue flashing cyclically until the problem is solved.
If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.
SYNC Indicators
Description
Possible Solution
The word clock is not set correctly.
Set the clock master and sampling frequency correctly on the MTX Editor or in
Dante Controller.
Dante Network circuit is broken.
Make sure that the Ethernet cables are
not removed or short-circuited.
(green) Unlit
(orange) Flash
(green) Unlit
(orange) Flash x2
If the green indicator is flashing, the unit is the clock master.
If the green indicator is lit, the unit is the clock slave and the clock is synchronized.
SYNC Indicators
Description
Possible Solution
(green) Lit or flash
(orange) Lit
(green) Lit or flash
(orange) Flash
(green) Lit or flash
(orange) Flash x 2
A non-GbE-compatible device is connected.
When transferring audio via Dante, use
device that supports GbE.
The Dante [SECONDARY] connector has taken
over communications during redundant network
operation.
Check the circuit connected to the Dante
[PRIMARY] connector.
An abnormality has occurred on the circuit connected to the Dante [SECONDARY] connector during redundant network operation.
Check the circuit connected to the Dante
[SECONDARY] connector.
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
29
Appendix
High-impedance and Low-impedance
Connections
For a high-impedance connection a speaker transformer that
raises the impedance to several hundred or thousand ohms is
added to the speaker system. This allows the speaker system to
be effectively driven with much lower current than is required
for a low-impedance system. That, in turn, makes it possible to
connect a larger number of speaker systems to each power
amplifier output. High-impedance speaker connections work at
a specific maximum voltage—usually 70 or 100 volts—and are
therefore also referred to as “constant voltage” speaker systems
(the label “constant voltage” is somewhat misleading: the actual
output voltage fluctuates according to the input signal).
For a low-impedance speaker connection, the power amplifier is
directly connected to a speaker system that has an inherent
impedance of 4–16Ω.
The difference between these types of connection are outlined
below.
 Multiple Speaker System Drive Capability
 High impedance
As long as the total nominal power input rating for all
speakers is within the power output capability of the
amplifier, any number of speaker systems can be connected in parallel. In a high-impedance installation, the
power input rating is determined by the speaker transformers used.
If the 280W output XMV8280 is used with a speaker system having speaker transformers that make the rated
input 10W, you can connect a speaker system with a maximum of 24 speakers per channel based on the calculation
(*), giving you a total of up to 192 speakers for the eight
channels. In a high-impedance installation it is also possible to simultaneously drive speaker systems that have different input power ratings.
(*) Yamaha recommends that you allow a 20% margin to
this number, considering variations in the transformer’s primary impedance, possible tap changes in
the future, and the addition of speakers.
Speaker transformer
70V/100V
10W
10W
10W
10W
10W
30 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
 Low impedance
Normally only one speaker system is connected to each
amplifier channel, as shown in the diagram.
This means that the number of speaker system that can be
connected to an XMV is limited to eight.
However, even with low impedance connections, there is
a way by which multiple speaker systems can be connected to one channel.
When multiple speakers systems having the same impedance are connected in parallel, the total impedance
becomes the individual speaker system impedance
divided by the number of systems connected. This means
that if the XMV is set to 4Ω, up to two 8Ω speaker systems can be connected to one channel.
Cannot be
connected
4Ω
8Ω
8Ω
8Ω
Total impedance = 4Ω
The second method is series connection. In this case the
total impedance is simply the sum of the impedances of
the speaker systems connected. But as you can see in the
series connection wiring diagram, if one speaker system
fails the second speaker system will be affected as well.
4Ω
4Ω
Interruption
Failure
No sound
Total impedance
= 8Ω
Appendix
 Transmission Distance and Efficiency
The cables that transmit electric signals have resistance. The
resistance in short cables is small enough that it can be
ignored, but as transmission distance and cable length
increase, resistance can increase to the point that signal loss
and degradation occur. That can mean reduced output level
and sound quality. Below we examine the merits and demerits of low-impedance and high-impedance connections in
relation to transmission over significant distances.
 High impedance
Even if the cable resistance reaches 8Ω due to an
extended transmission distance, this is an amount that can
be ignored relative to the impedance of the speaker system, meaning that transmission loss due to the cable will
be insignificant, and thus will have little effect on the
transmission efficiency of the electrical signal.
70V/100V
Long distance
Speaker
transformer (1kΩ)
Almost 100%
Cable resistance
= 8Ω
 Low impedance
For short distances over which cable resistance is insignificant, low-impedance connection allows the power
amp to be directly connected to the speaker system without the need for speaker transformers. That means that
the full performance potential of amp and speakers can be
taken advantage of for sound quality that is superior to
high-impedance installations. And since only one speaker
system is usually connected to each amplifier channel,
different audio signals can be sent to each speaker system, or “zone,” as required.
But in a situation like the one shown in the diagram,
where a long cable with a resistance of 8Ω is required,
transmission loss will theoretically result in the output
level being reduced by half because the impedance of the
speaker system itself is only 8Ω. Half of the power gets
absorbed by the cable, and only the remaining half is
available to drive the speaker. So for low-impedance
installations it is necessary to either keep the cables short
enough that cable resistance is not an issue, or use thicker
cables that have lower resistance for longer runs, for
example.
8Ω
Long distance
50%
Cable resistance
Speaker system
= 8Ω
inpedance = 8Ω
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
31
Specifications
General Specifications
XMV8280
XMV8140
XMV8280-D
XMV8140-D
4Ω
280W
140W
280W
140W
8Ω
280W
140W
280W
140W
4 Ω / DOUBLE POWER MODE
560W
280W
560W
280W
8 Ω / DOUBLE POWER MODE
560W
280W
560W
280W
100V (RL=40Ω/XMV8280)
(RL=80Ω/XMV8140)
250W
125W
250W
125W
70V (RL=20Ω/XMV8280)
(RL=40Ω/XMV8140)
250W
125W
250W
125W
Output Power
1kHz, THD+N=1%
(20 ms Burst)
High Impedance
Class D
Amplifier Type (Output Circuitry)
THD+N
Frequency Response
1kHz, half power, 4Ω
All channel output
0.2%
1kHz, half power, 100V, 70V
All channel output
0.2%
1W, 280W/8Ω, 20Hz–20kHz (XMV8280)
1W, 140W/8Ω, 20Hz–20kHz (XMV8140)
0dB, ±1.0dB
1W, 100V/70V, 55Hz–20kHz
Crosstalk
1kHz, half power, 8Ω
Att. max, input 150Ω shunt
-60dB
Residual Noise
A-weighted
280W, 8Ω
-65dBu
S/N Ratio
A-weighted
280W or 140W mode
100dB
+4 dBu (1.23V)
Input Sensitivity
Voltage Gain
Load Protection
100V
38.2dB
38.2dB
38.2dB
38.2dB
70V
35.2dB
35.2dB
35.2dB
35.2dB
280W (140W)/8Ω
31.7dB
28.7dB
31.7dB
28.7dB
560W (280W)/8Ω
34.7dB
31.7dB
34.7dB
31.7dB
Power switch on/off
Mute the output
DC-fault
Amplifier Protection
Thermal
Power supply shutdown
Mute the output (heatsink temp.
90°C) (return automatically.)
Overcurrent
Mute the output (return automatically.)
Low load impedance
Mute the output (return automatically.)
Power Supply
Protection
Thermal
Limiter Circuit
Clip limiting
Integrated power
Power supply shutdown (heatsink temp.
100°C)
Gain reduction (return automatically.)
Cilp limiter
3 speed fan x 2, front-to-back airflow
Cooling
+24dBu
Maximum Input Level
20kΩ (balanced)
10kΩ (unbalanced)
Input Impedance
Sampling Frequency
48kHz
A/D, D/A Converters
AD: 24-bit linear, 128 times over sampling
DA: 24-bit linear, 128 times over sampling
32 bit digital signal processing
Signal Processing
Latency
Analog input  [SPEAKERS] output
1.85msec
[YDIF] input 
[SPEAKERS] output (fs=48kHz)
1.08msec
—
[YDIF] input 
[SPEAKERS] output (fs=44.1kHz)
1.17msec
—
Dante [PRIMARY]/[SECONDARY] input 
[SPEAKERS] output (fs=48kHz, Dante
latency setup = 0.25msec)
—
1.33msec
Dante [PRIMARY]/[SECONDARY] input 
[SPEAKERS] output (fs=44.1kHz, Dante
latency setup = 0.25msec)
—
1.42msec
234 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Specifications
XMV8280
Controls
Front panel
XMV8140
XMV8280-D
Front panel (software)
ATT (-99dB to 0dB, 1dB step), POLARITY,
HPF (OFF, 40Hz, 80Hz), *40Hz or 80Hz for Hi-Z output setup
INPUT SOURCE (ANALOG/DIGITAL), SIGNAL LED (INPUT/OUTPUT)
Rear panel
AMP SETTING switch x 2 (OUTPUT FORMAT, IMPEDANCE, DOUBLE POWER
MODE, HI-Z LEVEL, per 2 channels),
SETUP switch (SECONDARY PORT,
LED DIMMER, PANEL LOCK,
IP SETTING, START UP MODE),
Rotary switch x 2 (UNIT ID HIGH,
UNIT ID LOW)
AMP SETTING switch x 2 (OUTPUT FORMAT, IMPEDANCE, DOUBLE POWER
MODE, HI-Z LEVEL, per 2 channels),
SETUP switch (UNIT ID, LED DIMMER,
PANEL LOCK, IP SETTING, START UP
MODE), Rotary switch (UNIT ID)
Connectors
Analog input
Euroblock (5.08mm pitch, balanced) /ch
Digital I/O
RJ45 x 2 (Dante [PRIMARY]/[SECONDARY])
RJ45 x 2 ([YDIF] IN/OUT)
Speakers
Barrier strip /ch
Network
RJ45 x 1
—
Remote
Euroblock (3.50mm pitch) x 1
Fault output
Euroblock (3.50mm pitch) x 1
Power
AC inlet x1
Indicators
[POWER] x 1 (green),
[ALERT] x 1 (red),
[PANEL LOCK] x 1 (orange),
[PROTECTION] x 8 (orange),
[LIMIT] x 8 (red),
[MUTE] x 8 (yellow),
[SIGNAL] x 8 (green),
[SELECT] x 8 (green),
[PRIMARY] x 1 (green),
[SECONDARY] x 1 (green),
[SYNC] x 2 (green, orange)
[POWER] x 1 (green),
[ALERT] x 1 (red),
[PANEL LOCK] x 1 (orange),
[PROTECTION] x 8 (orange),
[LIMIT] x 8 (red),
[MUTE] x 8 (yellow),
[SIGNAL] x 8 (green),
[SELECT] x 8 (green),
[NETWORK] x 1 (green),
[YDIF] x 1 (green)
3 digit, 7 segment numeric display
Display
100V, 120V, 230V–240V 50Hz/60Hz
AC Power Requirement
Power
Consumption
XMV8140-D
Power switch (rocker), Rotary encoder x 1,
[FUNCTION] button x 1, [SELECT] button x 8, [MUTE] button x 1
450 W
250 W
450 W
250 W
Idle (4Ω)
1/8 MAX power (4Ω)
73 W
73 W
73 W
73 W
Standby
23 W
23 W
23 W
23 W
0°C to +40°C
Operating Temperature
-20°C to +60°C
Storage Temperature
480 x 88 x 422 mm (18.9 x 3.5 x 16.6 inches)
Dimensions (W x H x D, including knob)
10.1 kg (22.3 lbs)
Net Weight
Included Accessories
AC power cord (2.5m) x 1, Euroblock plug (3-pin, 3.50mm pitch) x 2,
Euroblock plug with tabs (3-pin, 5.08mm pitch) x 8, Cable tie x 4, Owner’s Manual x 1
Optional Accessories
—
 [SIGNAL] Indicator Lit Level
XMV8280/XMV8280-D
XMV8140/XMV8140-D
Lit level
Lit level
dBu
Vrms
W
100V
8.7
2.11
—
70V
5.6
1.48
—
70V
5.6
1.48
—
560W/8Ω
5.2
1.41
0.249
280W/8Ω
2.2
1.00
0.125
560W/4Ω
2.2
1.00
0.250
280W/4Ω
-0.8
0.71
0.125
280W/8Ω
2.2
1.00
0.125
140W/8Ω
-0.8
0.71
0.063
280W/4Ω
-0.8
0.71
0.125
140W/4Ω
-3.8
0.50
0.063
100V
dBu
Vrms
W
8.7
2.11
—
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
235
Specifications
Block Diagram
DSP
CH A, B, C, D, E, F, G, H
G
SETUP
100V
INPUT MIX
AD
HA
Input:
Analog: 8
YDIF: 8
(XMV8280/
XMV8140
only)
ATT
XMV8280/XMV8140 only
YDIF
-3dBFS
In
-20dBFS
Out
ATT
DIGITAL INPUT
SENSITIVITY
SIGNAL
(OUT)
LIMIT
HPF
70V
80Hz
POLARITY
Dante: 8
(XMV8280-D/
XMV8140-D
only)
SPEAKERS
A, B, C, D, E, F, G, H
8ohms
40Hz
LIMITER
MUTE
DA
OFF
4ohms
AMP
8ohms
4ohms
ALERT
Output: 8
XMV8280-D/XMV8140-D only
PROTECTION
SIGNAL (IN)
Double Power mode:
Only Speakers A, C, E, G
Dante
-3dBFS
PRIMARY
-20dBFS
TEMP
DC-FAULT
OUTPUT
CURRENT
OUTPUT
VOLTAGE
INTEGRAL
OUTPUT
POWER
LOAD
IMPEDANCE
ATT
DIGITAL INPUT
SENSITIVITY
-3dBFS
AD
SECONDARY
-20dBFS
AMP PROTECTION LOGIC
Dimensions
3
11
2.5
10
382
409
414
422
430
480
88
76.2
463
(XMV8280/XMV8140)
11x6.5
480
88
76.2
463
(XMV8280-D/XMV8140-D)
11x6.5
Unit: mm
236 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Specifications
Current Draw and Heat Dissipation
 XMV8280/XMV8280-D
Power Specifications (PINK NOISE, 100V/50Hz mains)
MODE
standby
idle
1/8 output
power
1/3 output
power
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
Heat Dissipation
Btu/h
kcal/h
Line Current (A)
Power
Consumption (W)
Watts
Dissipated (W)
0.4
23
23
77
20
0.8
0.8
0.7
0.8
1.0
1.0
4.3
4.1
4.2
4.3
3.8
3.9
10.8
10.3
10.7
10.8
9.1
9.4
70
70
56
67
95
94
418
397
404
416
375
382
1031
980
1016
1040
873
905
70
70
56
67
95
94
138
117
124
136
125
132
284
233
269
293
206
238
238
238
189
228
323
320
469
398
422
462
425
449
967
793
916
997
702
810
60
60
48
58
82
81
119
101
107
117
108
114
245
201
232
253
178
205
Line Current (A)
Power
Consumption (W)
Watts
Dissipated (W)
0.4
23
23
77
20
0.7
0.7
0.6
0.7
0.9
0.9
3.6
3.4
3.4
3.5
3.2
3.2
8.8
8.3
8.6
8.8
7.4
7.6
70
70
57
67
94
94
415
394
401
412
371
377
1014
955
990
1010
857
882
70
70
57
67
94
94
135
114
121
132
121
127
267
208
243
263
190
215
238
236
195
228
318
319
459
388
411
449
411
432
909
708
827
895
647
732
60
60
49
58
81
81
116
98
104
114
104
109
230
179
210
227
164
185
Power Specifications (PINK NOISE, 120V/60Hz mains)
MODE
standby
idle
1/8 output
power
1/3 output
power
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
Heat Dissipation
Btu/h
kcal/h
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
237
Specifications
Power Specifications (PINK NOISE, 230V/50Hz mains)
MODE
standby
idle
1/8 output
power
1/3 output
power
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
280W/4Ω
280W/8Ω
560W/4Ω
560W/8Ω
100V
70V
Heat Dissipation
Btu/h
kcal/h
Line Current (A)
Power
Consumption (W)
Watts
Dissipated (W)
0.4
23
23
77
20
0.5
0.5
0.5
0.5
0.6
0.6
1.9
1.8
1.8
1.9
1.7
1.7
4.4
4.2
4.3
4.4
3.7
3.9
67
67
53
65
90
90
405
385
392
403
363
370
961
914
939
959
821
846
67
67
53
65
90
90
125
105
112
123
113
120
214
167
192
212
154
179
229
226
181
220
306
307
425
357
381
418
384
408
729
569
654
722
525
610
58
57
46
56
77
78
108
90
96
106
97
103
185
144
166
183
133
154
1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications.
1/3 power represents program material with extremely heavy clipping.
Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz
All channels driven
1W = 0.860kcal/h, 1BTU = 0.252kcal
Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].
 XMV8140/XMV8140-D
Power Specifications (PINK NOISE, 100V/50Hz mains)
MODE
standby
idle
1/8 output
power
1/3 output
power
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
Heat Dissipation
Btu/h
kcal/h
Line Current (A)
Power
Consumption (W)
Watts
Dissipated (W)
0.4
23
23
77
20
0.8
0.8
0.7
0.8
1.1
1.1
2.5
2.4
2.4
2.6
2.4
2.4
5.4
5.1
5.3
5.4
4.8
4.9
73
73
58
70
96
96
241
230
230
249
233
237
525
502
515
525
467
482
73
73
58
70
96
96
101
90
90
109
108
112
152
129
142
152
134
149
247
247
198
239
326
326
343
306
306
371
367
381
516
437
482
516
454
505
63
62
50
61
83
83
87
77
77
94
93
96
131
111
122
131
115
128
238 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Specifications
Power Specifications (PINK NOISE, 120V/60Hz mains)
MODE
standby
idle
1/8 output
power
1/3 output
power
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
Heat Dissipation
Btu/h
kcal/h
Line Current (A)
Power
Consumption (W)
Watts
Dissipated (W)
0.4
23
23
77
20
0.8
0.8
0.7
0.7
0.9
0.9
2.1
2.0
2.0
2.2
2.0
2.1
4.4
4.2
4.3
4.4
3.9
4.1
72
72
59
70
96
96
240
229
229
249
233
237
520
495
508
520
463
478
72
72
59
70
96
96
100
89
89
109
108
112
147
122
135
147
130
145
244
244
201
236
328
327
340
303
303
371
367
381
499
414
458
499
441
492
62
62
51
60
83
83
86
77
77
94
93
96
126
105
116
126
112
125
Line Current (A)
Power
Consumption (W)
Watts
Dissipated (W)
0.4
23
23
77
20
0.5
0.5
0.5
0.5
0.6
0.6
1.2
1.1
1.1
1.2
1.2
1.2
2.3
2.2
2.3
2.3
2.1
2.2
69
69
55
67
94
94
234
223
223
244
228
232
506
482
495
505
452
465
69
69
55
67
94
94
94
83
83
104
103
107
133
109
122
132
119
132
236
234
188
227
318
319
320
282
282
354
350
364
451
369
414
448
403
448
60
59
48
58
81
81
81
71
71
90
89
92
114
94
105
113
102
113
Power Specifications (PINK NOISE, 230V/50Hz mains)
MODE
standby
idle
1/8 output
power
1/3 output
power
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
140W/4Ω
140W/8Ω
280W/4Ω
280W/8Ω
100V
70V
Heat Dissipation
Btu/h
kcal/h
1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications.
1/3 power represents program material with extremely heavy clipping.
Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz
All channels driven
1W = 0.860kcal/h, 1BTU = 0.252kcal
Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
239
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic
products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in
accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste
disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
(weee_eu_en_01)
Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte
Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten
benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.
In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC bringen Sie alte Geräte
bitte zur fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.
Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und verhindern
mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten könnten.
Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche
Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.
[Information für geschäftliche Anwender in der Europäischen Union]
Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.
[Entsorgungsinformation für Länder außerhalb der Europäischen Union]
Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.
(weee_eu_de_01)
Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques.
Le symbole sur les produits, l’emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.
Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et
aux Directives 2002/96/EC.
En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la
sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d’un traitement inapproprié des déchets.
Pour plus d’informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez
acheté les produits.
[Pour les professionnels dans l’Union Européenne]
Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre
vendeur ou fournisseur pour plus d’informations.
[Information sur le traitement dans d’autres pays en dehors de l’Union Européenne]
Ce symbole est seulement valable dans l’Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la
méthode de traitement appropriée.
(weee_eu_fr_01)
240 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo
Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos usados no deben ser mezclados con desechos hogareños corrientes.
Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC.
Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial
efecto negativo sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los
desechos.
Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su
servicio de gestión de residuos o el punto de venta en el cual usted adquirió los artículos.
[Para usuarios de negocios en la Unión Europea]
Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor
para mayor información.
[Información sobre la Disposición en otros países fuera de la Unión Europea]
Este símbolo sólo es válido en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus
autoridades locales y pregunte por el método correcto de disposición.
(weee_eu_es_01)
Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura
Questo simbolo sui prodotti, sull’imballaggio e/o sui documenti che li accompagnano significa che i prodotti elettrici
ed elettronici non dovrebbero essere mischiati con i rifiuti domestici generici.
Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in
accordo con la Sua legislazione nazionale e le direttive 2002/96/CE.
Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti
negativi sulla salute umana e l’ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti.
Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il Suo servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli.
[Per utenti imprenditori dell’Unione europea]
Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori
informazioni.
[Informazioni sullo smaltimento negli altri Paesi al di fuori dell’Unione europea]
Questo simbolo è valid0 solamente nell’Unione Europea. Se Lei desidera disfarsi di questi articoli, prego contatti le
Sue autorità locali o il rivenditore e richieda la corretta modalità di smaltimento.
(weee_eu_it_01)
NEDERLAND / THE NETHERLANDS
• Dit apparaat bevat een lithium batterij voor geheugen back-up.
• This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur of
gelieve dan contact op te nemen met de vertegenwoordiging van Yamaha in uw land.
• For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha representative
office in your country.
• Gooi de batterij niet weg, maar lever hem in als KCA.
• Do not throw away the battery. Instead, hand it in as small chemical waste.
(lithium disposal)
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
241
242 XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
PA36
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
MALTA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Yamaha Music Europe GmbH Germany Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
ASIA
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AFRICA
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
Tel: +971-4-881-5868
MIDDLE EAST
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağımsız Böl. No:3, 34398 Şişli İstanbul
Tel: +90-212-999-8010
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
Tel: +971-4-881-5868
HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual
243
Yamaha Pro Audio global web site
http://www.yamahaproaudio.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
C.S.G., PA Development Division
© 2013-2014 Yamaha Corporation
厂名:雅马哈电子(苏州)有限公司
厂址:江苏省苏州市苏州新区鹿山路18号
Published 05/2014 改版 POHD-C0
Printed in China
ZF31880