Whirlpool 3XGSC9455 Specifications

东 尼 国 际 (香 港) 有 限 公 司
T o n y I n t e r n a t i o n a l (H K) C O., L T D
东 莞 市 华 科 东 尼 仪 器 有 限 公 司
Add: No.1 Tech Road, High & New Tech Development Zone, Songshan Lake, Dongguan City.
Tell: 0769-23010657/ 89770663
Fax: 0769-23010667
Email:lewis.huang@tonyhk.hk
Toys Testing Machines for ISO8124/EN71/ASTM F963 Mechanical and physical properties
Item 1.
TW-200 Drop Test Plate (drop test)
Simulate the real floor, to test the toys fall on the floor of the toys produced after the
destruction and damage caused by the impact of whether the product meet the requirements
dropped
Specification:1/8″×12″×12″(3mm thickness) 9 pcs
Material: polyethylene
Hardnes: Shore 80±10
Standards:ASTM F963 8.7.1; ISO 8124-1 5.24.2
weight: 6kg
website: http://tonyhk.hk / http://tony0769.com
laboratory
Page 1 of 60
complete solution of
Tony International (HK) Co.,Ltd
Item 2.
TW-200B EN71 Drop Test Plate (drop test)
Simulate the real floor, to test the toys fall on the floor of the toys produced after the
destruction and damage caused by the impact of whether the product meet the requirements
dropped
Specification:2mm Rubber+4mm SST Sheet 600mm×600mm
Hardnes: Shore 75±5
Standards: EN71-2011 8.5 drop test
Estimate the groups of ages applied to the toys tested according to the table
below
Age group
weight of toys
drop height
times
drop surface
standard
requir
ement
s
title
CPSC/
0-18 months
Less than 3 土
54.5 土 0.5
10
ASTM/CPSC
ASTM
0.01LB
inches
times
floor
F963—96a 18-36 months Less than 4 土
36.5 土 0.5
4 times
0.01LB
inches
36-96 months Less than 10 土
36.5 土 0.5
4 times
0.01L.
inches
EN71
0-14 years old
No limit
850 土 50mm 5 times
EN71 floor
The Safety Requirements of Toys Drop Test in Some International Districts
requirements
age
weight of toys
drop
times
height
standard
Australia
0-18 months specification 59 inches 10 times
39.5 inches 4 times
AS 1647
18 -168
months
England BS 5665
According to the standard of EN71
France NF 51-202
Standard in
≤3 years old
specification 4.5 inches 4 times
Canada
>3 years old
3 inches
4 times
Standard in Japan No age section
http://tonyhk.hk/http://tony0769.com
specification
Page 2 of 60
85 土 5cm
5 times
drop surface
CPSC/
ASTM
floor
CPSC/
ASTM
floor
OPSC/
ASTM
complete solution of laboratory
Tony International (HK) Co.,Ltd
floor
Item 3.
TW-201 Impact Tester (impact test)
Reduce the material damage or the danger of imitation toys protection devices as the real face.
Range: imitation protect device ( clear material protector, headpiece,cap,blinker)
Standards: EN 71-2011 8.7 impact test.
specifications:
1. dimension: 300(l)x300(w)x16(h)mm
2. adjust height: 0-200mm
3. impact hammer diameter: 80.00mm
4. impact hammer weight: 1Kg (hammer and rod)
5. with metric / lmperial unit height dicate ruler
Made of stainless steel
Item 4.
TW-203 Rattle Test Fixture (Geometric shape)
Oval / round bell tester (sound toy test template) is a simulation of children's oral capacity to
detect parts on the toys or toys may cause choking or swallowing, and dangerous
Material: aluminum alloy, surface oxidation
Size: 80*65*30mm (oval template)
73*73*30mm (round template)
Packing size:230*135*90mm
Weight:600g
Made of Aluminium material
http://tonyhk.hk/http://tony0769.com
Page 3 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
standard: 16 CFR 1510; ASTM F 963 4.21; EN71-2011 8.16 Geometric shape of certain
toys; GB6675-2003 A.5.3
made of Aluminium material
http://tonyhk.hk/http://tony0769.com
Page 4 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 5.
TW-204 Accessibility Probes AB
To determine whether any part or component of a toy can be contacted by the probe. The
probe simulates the finger of the infant or child touching the accessible points or edges of a
toy, which may then be subject to tests of sharp points or sharp edges.
Accessibility probes are designed for two age groups:
Probe A for 0-36 months
Probe B for 37-96 months
Standard: ISO8124--1: 5.7 accessibility of a part or component, EN71-1 2011 8.10
Net weight:330g
http://tonyhk.hk/http://tony0769.com
Page 5 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 6.
TTW-205 Test Fixture for Small Ball
Small ball test fixture is use to examine a toy up of whether small ball accessories may result
in the child swallow, stop breath way and esophagus to cause choking danger or not.
Standards:16CFR 1510 / ASTM F 963 4.6.2 /EN71-1 2011 8.32.1/ISO 8124-1 5.4 small balls
and suction cups GB6675-2003 A.5.3
made of Aluminium material
http://tonyhk.hk/http://tony0769.com
Page 6 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 7.
TW-206 Small Parts Cylinder
To determine whether toys & other articles intended for use by children under 3 years old
present choking, aspiration, or ingestion hazards because of small parts. If any objects can fit
completely into the cylinder without compressing & in any orientation, it is defined as a
"Small Part". Its internal dimensions simulate the fully expanded throat of a child under 3
years old.
Standards: 16 CFR 1500.48, ASTM F963 4.8, EN-71-1 2011 8.2 small parts cylinder, ISO
8124
Dimensions: 70*38*38mm
Weight: 430g
http://tonyhk.hk/http://tony0769.com
Page 7 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 8.
TW-207 Bite Test Clamp
Simulates a child biting the accessible area of toys. The part of the toy being tested is placed
in a bite test clamp & a specified force is applied for a specified period. The toy is then tested
to ascertain whether or not any hazards result from the bite test such as sharp points/ sharp
edges / small parts.
Dimensions:95*45*45mm
Weight:760g
Standard: ASTM F963, 16CFR 1500.52C, ISO8124-1 4.5
Purpose: The establishment of bite force testing method for imitating children who
playing toys or other things, using mouth to bite the toys result to the possibility of
damage or misuse.
2. Applies to:
2.1.Applies to toys or objects played by children under 8 years old.
2.2.The external dimensions is 1.25 inches ± 0.05 inches (3.18cm) or smaller, and
the design allows children to insert mouth in any way. When biting a thickness is
1.25 inches ± 0.05 inches (3.18cm), the insert depth is 0.25 inch at least .
2.3.Apply to mouth toys
2.4.This test is suitable for USA 16 CFR 1500.51,1500.52,1500.53 ‘s requirements
Item 9.
TW-211 Liquid Leak Test Needle
Diameter 1MM, the top radius 0.5MM, load 5N, for leakage testing,
Standard: ISO 8124-1 5.19/EN71-1 8.15 Leakage of liquid-filled toys; GB6675 A.5.19
Dimension Tolerance: + /-0.05mm
The thread needs the 0-100N push-pull meter.
http://tonyhk.hk/http://tony0769.com
Page 8 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 10.
TW-219 Projectile Velocity Tester
To determine the size catapults kinetic energy of toys, the ejection of parts of the test
apparatus through the tube or external testing of the components of the two sensors detect the
ejection toy parts used away after a certain period of time, it has calculated the move Energy.
The main instruments used for this test launch of baby toys or children's safety.
Clock out: 1 MHz
Display: 7 digit
Display rang : 0.000001 to 9.999999 sec
Projectile size: Large than 2mm diameter
Small than 35mm diameter ( for internal sensor )
Sensors distance: Fixed 150mm ( internal sensor )
Adjustable: 40mm - 420mm ( external sensor)
Dimensions: 240mm×310mm×130mm.
Weight: 8kg
Standards: ISO 8124-1 4.18:5.15 Kinetic energy of projectiles, bows and arrows
Item 11.
TW-220 Sharp Edge Tester
The Sharp Edge Tester is used to touch to examining a toy of position whether the existence
endanger safe sharp-edged edge, belong to the test item of the toy safety.
http://tonyhk.hk/http://tony0769.com
Page 9 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Dimensions: 260*120*180mm(L*W*H)
Weight: 1.99 kg
Standard: ISO 8124-1 4.6,5.8 sharp-edge test,, EN71-1 2011 8.11 Sharpness of edges
Accessories:
charging unit 1 pcs
foot switch 1 pcs
base plate 1 pcs
Standard import sharp edge tape 1 roll PTFE
http://tonyhk.hk/http://tony0769.com
Page 10 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 12.
TW-221 Sharp Point Tester
The Sharp Point Tester is used to examine a toy of position whether the existence endanger
safe of sharp-edged sharp point. Belongs to the test item of the toy safety; All accessorieses is
made of nonrust material . The technical parameters requirement of all countries is consistent.
Dimensions: 112x 16x16mm
Weight: 1 pound
Standards:
16 CFR 1500.48, ASTM F963 4.8, EN-71 2011 8.14, ISO 8124-1 5.9 sharp point test
Accessories:weight,batteries 2 pcs,bulb 2 pcs
Optional Accessories:
TN-W03 bulb
TN-W04 battery
Range:
1.
2.
This test applies to toys and items for children under the age of 8 used in
the normal use and both beofre and after abuse test(excluding the bite test)
result in contact part-ASTM/ CPSC.
This test applies to toys and items for children under the age of 14 used in
the normal use and both beofre and after abuse test(excluding the bite test)
result in contact part-EN71
Definition:
4.1. Accessible point – use the point tester describled in 16 CFR 1500.49 or EN71
18.10 to test any gap on toys
4.2. Toys -- It is means any kind of toy games or other toys for children which is
identified by any design, label advertising or other items.
4.3. Sharp point –- There are metal or glass sharp point in toys which must be tested
by point tester. If the indicator lamp lights up, then the sharp is identified as sharp point.
4.4. Inaccessible point – If the gap between metal or glass sharp point and other neighboring
surface is less than 0.02 inch after both before and after abuse test (excluding the bite
test), then such sharp point is inaccessible point.
4.5. Glass – It is a no crystallization of hard-brittle material that made from silica and silicate
http://tonyhk.hk/http://tony0769.com
Page 11 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
which contains soda and lime ingredients under the result of melting.
Item 13.
TW-224
Nail Bed Flammable Tester
Nail Bed Flammable Tester.Used in the detection part of the combustion of flammable hair,
and record the time, to see whether the burning of part of the meet flammability standards
Dimension: 25.4*25.4cm
Standard: ASTM F963, ISO 8124-2
Item 14.
TW-225 Surface Flammability Tester
I. Introduction
一﹑Purpose:This instrument is used in the examination down or the superficial
knowledge fabric’s flammability.
二﹑Principle: Butane burner is traversed across the face of the fabric to determine
whether surface flash occurs and to record any damage to the base fabric.
三﹑Applied standards: The instrument manufactured according to BS 4569 or
EN71-2 standard.
II. Instrument description
http://tonyhk.hk/http://tony0769.com
Page 12 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
一﹑physical construction:
1. physical construction: (figure 1)
11
10
1
2
3
12
4
13
5
6
0
7
14
8
1. 2. function description: 9
Figure 1
1.fixture board
2.burner
3.angle handle
4.control panel
5.flame adjustment knob
6.left shift buton
7.automatic button
8.right shift button
9.power switch
10.upper fixture
11.lower fixture
12.top plate
13.gas enter
14.base
 fixtrue board and the fixtures: sample holder,easy and fast to clampl the test
sample.
 burner: used to produce the required flame
 angle handle: used to change the burner direction(horizontal and vertical)
 flame adjustment knob:used to adjust the flame burning altitude
 left shift button: move the burner to left direction manually
 automatic: press this button to make the burner travelling the stroke
automatically
 right shift button: move the burner to right direction manually
 power switch: power on or power off
 gas enter: burning gases connection
二﹑Technical parameters (Table 1):
items
fixture length
burner move speed
http://tonyhk.hk/http://tony0769.com
specification
400mm
150±5mm/s
Page 13 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
burner stroke
≥300mm
fabric plush altitude
70mm
Space between two fixtures
100mm
sample dimension
length 200mm,width≥130mm,
sample amount for test
2 pcs
space between burner and sample
5mm
surface
space beteen burner center to
15mm
lower fixture
burning gases
butane gas
size(WxDxH)
60x41x32cm
weight(Kg)
power
≈20Kg
1∮ AC 220V 5A
Table 1
Item 15.
TW-226 Toys Comprehensive Flammability Tester
It is used for testing the flammbility of toys,children clothes,evalute the following toys
flammability speed,time.
Testing the child clothing or the toy and accessories’s flammability , appraises the following
toy type the repidity of the flammability and time
The PLC control, the time is accurate, English man-machine contact surface
The different test method provides different sample jig
clamps are easy to operated
The jig may adjust willfully, suits different sample
Comply to standard EN71-2 2011, ISO 8124-2 5.2/5.3/5.4/5.5/5.6 2007
Summary
http://tonyhk.hk/http://tony0769.com
Page 14 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
This tester was designed according to EN71-2008 standard, both sell to overseas and
dometic market.
(1) Adopt the mininsize gas cylinder system, the instrument can be moved, take up
small space. The user also can connect big gas cylinder.
(2) The gas system is controlled by PLC, ignite and continue burning time are
accuracy,
(3) All frames can be adjusted to meet different testing need.
This instrument applies to test the performance of flame retardardant of toys for
children, completely applies to EN71-2-2008.
Main technical parameters
1、Ignition time set range:0~99.99S
Precision:0.01S
2、continue burning time range :0-999.9S
precision0.1S
3、Please put this flammability into a cabinet to make test.
4、Ignition mouth size: applies to IS0 6941 standard.
5、Dimension of specimen: 150mmX560mm
6、Power: AC200V 50Hz
7. Weight:40KG
8 Gas: butane gas。
9 Thread: white cotton thread.
Gas Device
Control Panel
http://tonyhk.hk/http://tony0769.com
Page 15 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Construction
I
G
E
D
C
B
A H
F
A: Baseplate used for collecting the toy combustion residue, facilitates clean.
After using in collects the toy combustion residue, facilitates cleanly
B: Control panel
C: butane cylinder
D: burn head
E: ignition mouth (applies to ISO 6941 standard)
F: Burner
G: 45degree U type test clamp
H: The first , second mark thred hammer and min switch
I: Head fix frame
Spare Parts for the EN71 Toys Flammability Testing
http://tonyhk.hk/http://tony0769.com
Page 16 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Cotton thread
for Mark
Gas Device
45 Degree U Frame
Supporter
Hammer
Flame Meter
Flame Supporter
Gas and Flame Lighte (but could not be sent as the forbidden goods)
http://tonyhk.hk/http://tony0769.com
Page 17 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 16.
TW-227 45 degree Flammability Tester
Brushing device
45 degree flammability tester, check the flammable performance of the textile
Stainess testing room with glass window,after ignition automatic time (0.01 second precision)
automatic or
parameters:
Manual firing device, including sample holder and brushing device.
Spread time scope: 0-99.99s
Firing time: 1s or specified
Resolution: 0.01s
Igniter model: comply to ASTMD1230
Standards: ASTM D1230 FTMS 191-5908 CRF 16-1610 CALIF TB 117 NFPA 702
ISO 8124-2
Power Supply: 220V
Control Panel
1.Button Function
Ts:Ignition Time
T1:Spread Time
T2:Smoldering Time
START:Start button, to make the equipment start to test.
STOP:stop button, to stop running the equipments.
TETUP:setting button,using to set the ignition time.
MANUAL:manual button, Press START button while pressing this button, fire mouth repeat
to move up and down.
FIRE:Ignition button
http://tonyhk.hk/http://tony0769.com
Page 18 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
AUTO:automatic button,can switch manual status back to automatic status.
Press SETUP button, Ts showed a flashing indication on the left, through the UP, DOWN
keys to change the value, press the SETUP key to exit the setting mode.
Item 17.
TW-228 Toy Box Cover Durability Tester
The machine applies to test the durability of toys lid switch that can be repeated.Through toys
ld movements by the driven force of a rotating pendulum, to simulated hinged part of the toy
lid is intact or not after a certain number of repeated opening and closing movements.
item
specification
Sample for test
One pcs for each test
15 second for opening and closing
Test speed
movement each cycle.
pendulum rod moving angle
0°~80°
Test times
7000 times
Counter
LED display, 0~9999 times
Max height
700mm
Gas source
6kgf/cm^2
Dimesion(WxDxH)
97.5x35x126cm
http://tonyhk.hk/http://tony0769.com
Page 19 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Weight
约 30kg
Power
1∮ AC 220V 3A
Box cover durability tester.
Control mode: Controlled by Micro-computer automatically
Action mode: Electromotion or Automatism
Test pieces: Stop automatically
Standards: 16 CFR 1500, ASTM F963 4.8, EN-71, ISO 8124 -1 5.13
Item 18.
TW-229 Mouth Toy Endure Tester (Gas operated type)
To prevent mouth moving toys or children's mouthpiece has been mistakenly inhaled and
cause a choking hazard
Features: 1. Instruments to meet the 5s at least 295 cubic centimeters within + / -10 cubic
centimeters of gas, and can be 10 times alternately blowing, suction toy.
Specification:
Test speed 120/min
Specimen Fixture casing 2 groups
barometer ±15Kpa adjustable
power:220V/50Hz,3A.
dimension (L*W*H):650×400×260
Weight: 15 kg
standards:EN71.8.17, ISO 8124-1 4.25,5.20,ASTM F963 8.13 Durability Test for
Mouth-Actuated Toys.
It needs additional air compressor by customer.
http://tonyhk.hk/http://tony0769.com
Page 20 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 19.
TW-229 Mouth Toy Endure Tester (electrodynamic type)
To prevent mouth moving toys or children's mouthpiece has been mistakenly inhaled and
cause a choking hazard
Features: 1. Instruments to meet the 5s at least 295 cubic centimeters within + / -10 cubic
centimeters of gas, and can be 10 times alternately blowing, suction toy.
2.This instrument is electrodynamic type, has air source inside, no need additional air
compressor.
Specification:
Test speed 120/min
Specimen Fixture casing 2 groups
barometer ±15Kpa adjustable
power:220V/50Hz,3A.
dimension (L*W*H):600*400*240mm
Weight: 35 kg
standards:EN71.8.17, ISO 8124-1 4.25,5.20 durability of mouth-actuated toys
Item 20.
TW-230 Sound Level Test Stand / Acoustic testing equipment
http://tonyhk.hk/http://tony0769.com
Page 21 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Energy along the X, Y, Z (X displacement:0-1000MM; Y displacement of 0-1700MM; Z
displacement: 0-1800MM) slide freely positioning the three directions.
Flat with horizontal and vertical angle adjustment instructions: 0-1800;
Optical ranging device, measurement noise, the distance between the meter and toys;
Dimension (L * W * H): about 1880 * 1150 * 2200mm
Material: Aluminum
Item 21.
TW-246 EN 71 Compression Head
dimension:28*28*19mm
diameter 30 mm round rod
Standard: EN71-1 2011 8.8 /ISO 8124-1 5.24.7compression test
made of Aluminium material
Item 22.
Head Probe C (EN71-1 2011)
Head probe for EN 71-1: 2011, 5.3,
A.29 Cords
head probe representing children of less
than 3 months, to test the cords and
chains in toys
http://tonyhk.hk/http://tony0769.com
Page 22 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 23.
TW-260 Sound Level Meter
The Sound Level Meter has been designed to meet the measurement requirements for
industrial safety offices and sound quality control in various environments.
Test range: 30 to 130 dB
Dynamic Range: 60dB
Resolution: 0.1dB
A and C frequency weighting
Maximum and minimum volume includes occurs time
Fast time , slow time weighted.record and read the manual volume
Standards: IEC61672-1 : 2002 Class 2 .ISO8124-1 4.28 Acoustic requirements
IEC60651 : 1979 Type 2
ANSI S1.4 : 1983 Type 2
Digital Display: LCD 4 digit display, 0.1dB resolution, 1 second
Analog Display: 60 bar code instructions, 1dB resolution, 8 times per second
Test Range:30dB - 130dB
Measuring frequency range: 31.5Hz - 8KHz
Microphone 1 / 2 inch class of condenser microphones
TES-1350A Noise Meter
Range:
A LO (Low) - Weighting: 35- 100dB
A HI (High) - Weighting: 65-130dB
C LO (Low) - Weighting: 35- 100dB
http://tonyhk.hk/http://tony0769.com
Page 23 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
C HI (High) - Weighting: 65-130dB
Resolution: 0.1dB
Frequency Range: 31.5Hz to 8KHz
Accuracy:±2dB
Dynamic Range:65dB
Frequency Weighting: A、C
Time Weighting: Slow & Fast
Maximum Hold: Decay < 1dB/3min
Microphone: Electret condenser microphone
Calibration: Electrical calibration by using the internal oscillator (1KHz sine Wave at 94dB)
Auxilitary Output: AC conditioned, 0.65Vrms corresponding to each range step, impedance: 600
W
DC conditioned, 10mV/dB (nominally)
Operating Condition: 0℃ to 40 ℃< 80% R. H.
Storage Condition: -10℃ to 60 ℃< 70% R.H.
Display: 3 1/2 digitals
Power Supply: one 9V battery
Size: 240mm(L)x68mm(W)x25mm(H)
Accessories: Instruction Manual,9V Battery,Carrying Case,Screwdriver,Windscreen.
Standard applied: IEC 651 Type2
Item 24.
TW-270 Inclined Plane Device for Stability Test
Inclined plane device angle ajustable range: 0-15degree
Aluminum frame
Inclined plane use imported plate,19mm Fine core plate
Use P60 alumina and abrasive paper to cover the plane.
http://tonyhk.hk/http://tony0769.com
Page 24 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
oblique plane size:W*L1000*3000mm
Use the toys can be loaded one child weight.
Loading on the toys,which is worst standing position or seating position,
Children below 36months(including)Loading 25㎏±0.2㎏,
Children above 36months,loading 50㎏±0.2㎏
Loading on the toys,put the toys on the 10±1degree Inclined plane
If the toys can be loaded one child weight.standing or seating should be testing,to determine
whether the toys will be fall down
Heavy immobile toys,put the toys on 5°±1° oblique plane,ajust removable parts position,get
the worst position to test.
Standards: ASTM 963 ,EN71 8.18.1, ISO8124-1 5.28/29
Item 25.
Static Strength Weight TW-268
Place standard load on the
surface of standing toy or riding
toy.Then move the load,measure
toy whether there is crack in any
accessories,whether they can
meet the related standard.
Less than or equal to 36 months:
25KG weight +-0.2KG
More than 36 months: 50 KG
weight + 0.5 KG
Standards: ASTM 963 ,EN71
8.18.1, ISO8124-1 5.26/28/29
Model: TW-268A 25KG
Weight; TW-268B 50KG
Weight
http://tonyhk.hk/http://tony0769.com
Page 25 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 26.
TW-269 25kg /50kg Dynamic Strength Weight
specification
part weight(Kg) diameter(mm) height(mm)
a 10.42 150±2 75±2
b 14.58 178±2 75±2
c 4.16
d 2.00
e 0.50
Standard: EN71-1 2011 8.22.2, ISO8124-1 5.27
http://tonyhk.hk/http://tony0769.com
Page 26 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 27.
TW-232 Flat Claw Clamp
Used for assisting pull testing,made of stainless steel
Dimension: 167*60*13MM
Standards: ISO 8124-1 5.24.6.1 tension test
Item 28.
TW-233Hair Claw Clamp
Used for assisting hair tension testing
Dimension: 116*82*16MM
Material: stainless steel fixture, rubber grip
Standards: ISO 8124-1 5.24.6.1 tension test
Item 29.
TW-234 Long Mouth Clamp
used for assisting pull testing , made from adaption of USA VISE-GRIP 6LN
Dimension: 218*43*13MM
Material: stainless steel
Standards: ISO 8124-1 5.24.8 flexure test
http://tonyhk.hk/http://tony0769.com
Page 27 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 30.
TW-236 Big Mouth Clamp
used for assisting pull testing , made from adaption of USA VISE-GRIP 5WR; 7CR; 10CR
redo
Dimension: 190*49*14MM
Material: stainless steel
Standards: ISO 8124-1 5.24.6.1 tension test
Item 31.
TW-237 Pull Hook
Used for wheel pull testing fixture, made from stainless steel
Dimension: 210*31*25MM
Material: stainless steel
Standards: ISO 8124-1 5.24.6.1 tension test
Item 32.
TW-238 Single Tension Hook
Horizontal type,made from stainless steel
Dimension:110*31*20MM
Standards: ISO 8124-1 5.24.6.1 tension test
http://tonyhk.hk/http://tony0769.com
Page 28 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 33.
TW-239 Two Claw Clamp
Stainess steel, used for testing eyes, nose etc....
Dimension:105*30*25MM
Standards: ISO 8124-1 5.24.6.1 tension test
Item 34.
TW-240 Three Claw Clamp
Stainess steel, used for testing eyes, nose etc....
Dimension: 105*37*26MM
Standards: ISO 8124-1 5.24.6.1 tension test
Item 35.
TW-241 Seam Clamp
For assisting suture pull testing used. Made from adaption of USA VISE-GRIP 6LN
Specification: jaw diameter19 mm, round handle
Standards:ASTM F963 8.9.1.1, EN71-1998 8.4.2.2, ISO8124-1 5.24.6.2; 5.24.6.3
Size: 218*40*22MM
Length: 6 inches
http://tonyhk.hk/http://tony0769.com
Page 29 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 36.
TW-243A Torque Clamp (big size)
Used for clamping the sample during the wrest testing
Stainless steel and aluminum, and copper
Single screw type,big size
Standard: ISO8124-1 5.24.5 torque test
Item 37.
TW-247 ASTM/EN Flexure Test Fixture
Used to test the toys from the increase in rigidity or fixed shape of the metal wire or other
metal materials used in the bending (or abuse) the process, whether due to fracture a risk of a
sharp tip or sharp edges protruding. Abuse testing program is a toy. Made of stainless steel
material. United States, Europe and China national standard test board size requirements vary.
Model: American USA Europe meet European Union
Standards: 16 CFR 1500.48 16 CFR 1500.49 EN-71 , ISO 8124-1 4.9: 5.24.8 flexure test
Thickness:2.28 mm
http://tonyhk.hk/http://tony0769.com
Page 30 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 38.
TW-250 Infrared Thermometer
Features:
a) simple one-hand operation;
b) laser targeting;
c) LCD with back light;
d) C/F select switch;
e) laser on/off switch;
f) automatic power off;
g) display hold function
Standard: ISO8124-1 4.23: 5.18
Item 39.
TW-257 2m/s Tester
This instrument is mainly used for test rides at the speed of toys 2m / s when the value
of the barrier imposed by force. Toys will be under test placed on the conveyor belt,
the drive wheel until the toy speed of 2m / s and remain stable; the display shows the
pressure sensor to the force sensing value, according to ability to judge the value of
toy safety.
Conveyor belt Speed :2m/s (can be adjusting)
Dimensions:1530x630x750mm
Weight:750kg
Standards:16 CFR 1500 ASTM F963 8.20 ;ISO 8124 5.17
http://tonyhk.hk/http://tony0769.com
Page 31 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 40.
TW-257 2m/s Tester
Dynamic strength tester is mainly used for testing function of the kids riding tricycle after hitting
the 50x50mm barrier at the speed of 2m / s
Purpose
This instrument imitates the state of children riding tricycle, put certain load on the sample,
make it hit the 50x50mm barrier at the speed of 2m/s, then check if the sample structure and
properties is good.
Standards: This instrument manufactures refer to EN 71 section 8.22
Sample :Children tricycle
Number of sample:1pcs
Test speed: 2±0.2m/s
Barrier Block: 50mmx50mm
Width of testing channel: 90cm
Dimensions: 153x450x156cm
Control cabinet: 36x32x100cm
Weight: ≈650Kg
Power Supply: 1∮ AC 220V 50Hz
Item 41.
TW-317 Digital Push & Pull Meter
Ergonomic, durable, heavy-duty metal construction
· Push-button selectable lbf, kgf, and Newton units
· Programmable High/Low setpoints with LCD indicators
· Overload capacity 200% F.S.
http://tonyhk.hk/http://tony0769.com
Page 32 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
· Overload alarm, display flashes at overload limit
· Low battery icon
· Selectable real time or peak mode operation
· Push-button tare function
· Reversible display
· Set of six adapters, AC charger/adapter and carrying case
DS2 digital force gauges feature a large, easy-to-read LCD display and simple
push-button operation. An ergonomic metal housing protects the highly accurate
loadcell and electronics in tough industrial environments.
· Accuracy: 0.2% F.S. LSD
· Selectable units: lbf (ozf), kgf (gf) or newtons
· Overload Capacity: 200% of F.S. (overload indicator flashes beyond 110% of F.S.)
· Data Processing Speed: 1000 data/second (30 data/second rate selectable)
· Display Update: 10 times/second
· Power: Rechargeable Ni-MH battery pack or AC adaptor
· Battery Indicator: Display flashes battery icon when battery is low
· Setpoints: Programmable high/low setpoints with LCD indicators
Item 42.
TL-405 Pointer Force Guage
With simple operation, precision, peak value maintance, indicate two scales in KG and
Newton.
Application: electrics,components of Vehicle, Lighter & portfire , construction, fabric etc.
Handheld design, compact
Easy operation
Capacity: 10KG,20KG,30KG,50KG
Precision: ±1%
Travel: 10mm
http://tonyhk.hk/http://tony0769.com
Page 33 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 43.
TL-412 Imada Push&pull Scale
The rugged construction of the FB/PS force gauges will withstand industrial environments
and yet retain calibration for extended periods.
Ergonomic design makes it ideal for hand held use, or it can be mounted to a test stand. The
Zero-Tare ring allows you to zero the gauge to compensate for measuring attachments and
changes in measuring position. The real time/peak hold selector switch allows you to observe
transients or capture peaks. Many ranges are available to cover all of your measurement needs
(also available in Newtons).
The FB series is sold in kits complete with force gauge, hard carrying case, five measuring
attachments (flat head, conical, chisel, notched, and small hook) as well as a 3 inch extension
shaft.
FB/PS Force Gauge Details :
a) Model: FB/FS manufacturer: Imada
(Japan)
b) Simple, rugged, virtually maintenance free.
c) Retains a high degree of accuracy for extended periods.
d) Ergonomic, heavy-duty metal construction.
e) No batteries needed.
f) Intrinsically safe in hazardous environments.
g) Capacity up to 150 lbf (push and pull).
h) Overload capacity 165 lbf on all ranges.
i) Tare ring.
j) FB Ranges (Resolution) Accuracy: 0.3% F.S.
k) Real time and peak mode.
l) Full set of accessories and carrying case included.
http://tonyhk.hk/http://tony0769.com
Page 34 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 44.
TL-404 TTF Push Pull Tension Tester
It is used for providing large and steady strength during the tension testing
Most use in toy ‘s damage tension testing, provide the strength by air cylinder
Push-pull intensity maximum: 188/168kgf
Cylinder trip maximum: 125mm
Adjustable speed: 50-800mm/s
Cylinder base plate trip: 0-500mm
Withstanding pressure cylinder: 13.5kgf/cm2
Jaw size: 90 *40 mm
Adjustable stroke left jaw: ± 60 mm
Adjustable upper and lower jaw :0-120 mm stroke
Dimensions: 1620*320*420 mm
Weight: 80kg
Standards: 16 CFR 1500, ASTM F963 4.8, EN-71, ISO 8124
Item 45.
TNJ-041 AATCC Washing machine (Whirlpool)
http://tonyhk.hk/http://tony0769.com
Page 35 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Selected and certified for AATCC Test methods requiring repeated home laundering
(methods 88 B+C, 124, 130, 135, 142, 143, 150, 172 and 179). Available in US
domestic and international electrical specifications.
Application:To determine the dimensional stability (shrinkage or growth) of woven or
knit textile fabrics and garments that take place when fabric are subjected to the
conditions of consumer laundering. It has an attractive and durable appearance in
modern testing laboratory. Available in US domestic (110V, 60Hz) and international
(220V 50Hz) electrical specifications.
Features:AATCC recommended.
Model: 3XGSC9455
Top-loading home laundry washer.
Extra large capacity tub
Power Supply: 220V or 110V
dimension
1095× 685× 675mm
washing capacity
washing method
18 pound/8.2kg
rolling plus stirring
Selected and certified for AATCC Test methods requiring repeated home laundering
(methods 88 B+C, 124, 130, 135, 142, 143, 150, 172 and 179).
Essential proberty:
1. Washtemperature: 60 Degree Celsius +-3° or 140°Degree Fahrenheit +-5°.
2. Lukewarm-washing cycle: 29 Degree Celsius +-3°or 85 Degree Fahrenheit +-5°.
3. regular laundry / Cotton/Sturdy: 12 minutes
Below consumables are only for your reference.
AATCC Detergent (WOB)
http://tonyhk.hk/http://tony0769.com
Page 36 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
AATCC 1993 STD WOB Detergent (Without Optical Brightener),24 LB/Tub
Standard: AATCC 61
AATCC Detergent (with brightener)
AATCC 1993 STD REF Detergent,drum of 24LB
Standard: AATCC 135&150
Item 46.
TNJ-042 AATCC Dryer Machine(whirlpool)
Selected and certified for AATCC Test methods requiring repeated home laundering (methods
AATCC 88 B+C, 124, 130, 135, 142, 143, 150, 172, and 179). Available in US domestic
and international electrical
It is a shrinkage tester appointed by American AATCC
Meets to AATCC standard testing method (88B+C, 124, 130, 135, 142, 143, 150, 172 and
179)
Drying methods: drying time for pre-school / incomplete dry clothes,air-dry; strong drying /
incomplete dry clothes; automatic rotation 30-90 minute, cold crease.
Techniques:
Dimension:740× 710× 1100mm(L× W× H), 29*28*43Inch
http://tonyhk.hk/http://tony0769.com
Page 37 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Drying capacity: 18 pound/8.2kg
Place of original: USA
Weight: 60kg(130LB)
Power: 220V/50Hz/30AN
WEIGHT:60 kg 130 lb
Item 47.
ISO Standard Precision Tumble Dryer
Standardised tumble drier.
Accurately test the drying temperature
Programmed time setting, digital temperature control
Machine size: 600 × 600 × 850mm
Weight: 35Kg
Maximum Load: 5Kg (dry weight)
Power Requirements: 230V, 2400W, 11A
Standard BS EN ISO 6330:2001, AATCC135, Marks & Spencer Plc, and other retail
standards
http://tonyhk.hk/http://tony0769.com
Page 38 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 48.
TW-258 SAFQ Button Pull Test Machine
The button snap tester.To determine the holding or breaking strength of prong-ring attached snap
fasteners onto garments. Consists of an Upper Snap Clamp, a Lower Fabric Clamp & Force Gauge
mounted on a Stand. The snap component is gripped by the Upper Snap Clamp and the garment is
fixed to the lower Fabric Clamp. By turning the Top Flywheel, the operator can apply a specific
force and the holding force or the breaking strength can be recorded.
Used for measuring the responsibility of garment manufacturer to ensure
button and firmware can be fixed on the ready-made garments properly,
Avoiding button drop from garment to brought danger to baby swallow.
Used for testing the vertical orientation tension of button and added touch.
Dimensions : 280 x 230 x 735 mm (L×W×H)
Weight:25 kg
Standards: 16 CFR 1500.51-53, ASTM WK4510 PS79-96,ASTM F963,EN71-Part1,M&S
P115A(for snap) P115(for button)
Package weight and size: 40kg; 87*43*33cm
http://tonyhk.hk/http://tony0769.com
Page 39 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Standard Accessories:
Upper Universal Clamp 1pcs
Test for female part of snap and male part of stud.
Uper Stud Clamp 1pcs
Test for male part of baby snaps but generally Upper
Three Pronged Clamp 1pcs
Test for four-hole buttons and Jeans buttons.
Two Pronged Clamp 1pcs
Upper Grasp Button Clamp 1pcs
Designed to gripping the grasp buttons or larger buttons,
e.g. Jeans or Plastic Button up to 30 ligne.
Lower Fabric Clamp , Lever Arm locking 1pcs
Fix the sample with buttons firmly, flatly and constantly so that fabric
slippage can be minimized .
http://tonyhk.hk/http://tony0769.com
Page 40 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Upper Long Nose Vise Clamp 1pcs
Mainly used for trouser hooks and other smaller accessories.
Seam Test
Clamp
For assisting suture pull testing used. Made from adaption of USA
VISE-GRIP 6LN
Specification: jaw diameter19 mm, round handle
IMADA Push-pull Scale FB 100LB 1pcs
Dislay the reading of pulling force with capacity up to 100LBS
Calibration Weight 15 LB 1 pcs
Routine checking the accuracy of the Imada Force Gauge.
http://tonyhk.hk/http://tony0769.com
Page 41 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Item 49.
SP752 UV-Vis Spectrophotometer
(made in China)
An UV-Vis spectrophotometer with power on self-testing, automatic wavelength calibration, light
source auto-switching, PC controlled, etc.
SP-752 UV-Vis spectrophotometer takes use of high precision sine mechanism as a wavelength
driver.
Program control, wavelength accuracy, and the linearity over the full wavelength are obviously
better than those of the congener instruments in which gear and rack is used as a wavelength
driver, and a gauge dial is used for wavelength display.
Parameters:
Photometric system
Single beam
Wavelength range
200-1000nm
Spectral bandwidth
5nm
Wavelength accuracy
±2nm
Wavelength repeatability
1nm
Photometric accuarcy
±0.5%T
Photometric repeatability
0.3%T
Stray light
≤0.5%T
Baseline stability
±0.002A/h(500nm 处)
Baseline flatness
-
Noise level
Photometric range
Data output
Printout
http://tonyhk.hk/http://tony0769.com
±0.002Abs
0-125%T、-0.097-3A
USB connector
Parallel Port
Page 42 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Display system
Light source
2*20 large screen LCD
Import long-life tungsten lamp、deuterium lamp
Detector
Import Si Photodiode
Overall dimension
475*420*180mm
Power
AC 220V/50Hz or 110V/60Hz
Weight
11kg
Standard Equipped Assessories:
1. manual Cuvettes Holder 10mm 1 pcs
2. 10ml standard glass cuvet 4 pcs
3. 10ml standard quartz cuvet 2 pcs
4. RS-232C line 1 pcs
5. Power line 1 pcs
6. Manual book 1 pcs
7. Win-Spec Software Win-sp5.0
Item 50.
UV1700 Spectrophotometer (Made in Japan)
It could be said that spectroscopy-based applications fall into two broad categories: Analytical
determinations and routine quality control of sample preparations.TheUV-1700 spectrophotometer
is suitable for both of these uses as it integrates accuracy, simplicity, and long-life among its
features.
Scan-type spectrophotometer Features:
A) Wide wavelength range, satisfying requirement of various fields.
http://tonyhk.hk/http://tony0769.com
Page 43 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
B) Three options for spectral bandwidth selection: 5nm, 2nm and 1nm, made according to
customer's need and satisfy the requirements of pharmacopoeia.
C) Manual 4-cell holder accommodates width pathlength cells.
D) Optimized optics and electronic system design with over 30-year experience, ensuring high
performance and reliability.
E) Rich measurement method adopted: Wavelength scan, time scan, multi-wavelength
determination, etc., meet different measurement requirement.
F) Automatic 10mm 8-cell holder design, changeable to automatic 4-cell holder for 5mm~50mm
cells.
G) The measured data can be printed out. RS-232 interface available for connecting computer.
Parameter and standard curve can be saved.
This device is sensitivity, reliability and that it is user-friendly. Installation and Operational
Qualifications at start-up, light source automatic position adjustment.
Specifications of UV Spectrophotometer:
Wavelength range
190 to 1100nm
Spectral bandwidth
1nm (190 to 900nm)
Wavelength display
0.1-nm increments
Wavelength setting
0.1-nm increments (1-nm increments when setting scanning
range )
Wavelength accuracy
±0.3nm @ 656.1nm D2
Wavelength repeatability
±0.1nm
less than 0.05% NaI @ 220nm, NaNO2 @ 340nm
Stray light
less than 1.0% KCl @ 198nm
Photometric system
Double Beam
Photometric range
Absorbance: -0.5 to 3.999 Abs
Transmittance: 0% to 300%
±0.002 Abs (0.5Abs)
Photometric accuarcy
±0.004 Abs (1.0Abs)
Photometric repeatability
±0.001 Abs (0.5Abs)
±0.002 Abs (1Abs)
Baseline stability
less than 0.001 Abs/H @700nm
(one hour after light source turned ON)
http://tonyhk.hk/http://tony0769.com
Page 44 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Baseline flatness
±0.001 Abs
(200 to 1100nm,one hour after light source turned ON)
Noise level
0.002 Abs
Dimensions (W×D×H)
550(W) x 470(D) x 200(H)
Weight
17kg
Printers
DPU, ESC/P, PCL printers, USB I/F Windows-compliant
printers are available with USB memory and PC software
Memory
USB memory (option) Saved as text and UVPC file
Performance for PC
USB memory + UVProbe (standard) Win
Item 51.
TW-315 Desktop Tension Tensile Strength Tester
This machine can widely apply to a variety of different textile materials and wood,
shoes, tires, rubber tubes, triangular tape, plastic sheeting, plastic sheeting, packaging
films, acrylic, FRP, ABS, EVA, PV and other products , semi-or dumbbell-shaped
specimens of the tensile strength, elongation, tear, glue focused, tensile stress, peel,
shear, the sticky relay of rubber and metal by using different fixtures
Parameters:
Capacity:5,10,20,50,100,200kg(or specified)
Load accuracy: ±0.5%
http://tonyhk.hk/http://tony0769.com
Page 45 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Switch unit:Kgf,lbf,N
Load solution: 1/10,000
Test speed: 30~500mm/min
Displacement accuracy: 0.001mm
Max stroke: 650mm/800mm/1000mm
Power:220V.60Hz, 24Am
Dimension: 500*460*1510mm
Weight:80 KG
Stroke Resolution: 0.1 mm
Data sampling frequency: 16 times / sec
Motor: servo motor (Taiwan)
Item 52.
TW-029 Dual Arm Computer Servo Tensile Strength Test Machine
http://tonyhk.hk/http://tony0769.com
Page 46 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
This tensile machine can do various tensile testing in the field of rubber, plastics,chipboards,
foam, plastic, film, flexible packaging, pipes, textiles, fibers, nanomaterials, polymers,
composite materials, synthetic materials, packaging, paper, wire and cable, fiber optic cable,
wirecables, seat belt, seat belt, leather belt, shoes, tape, polymer, copper, spring steel wire,
stainless steel, castings, brass, non-ferrous metals, car parts, alloys and other
non-metallicmaterials and metallic materials tensile, compression, bending, tearing, and 90 °
peel, 180 ° peel, shear adhesion, pull-out strength, an extension of the elongation test.
I. Features:
1, high-precision: ± 0.5%, high-resolution: 1/200000;
2, selectable programmable control: to achieve loop control of load, position, deformation,
and time;
3, Using PHILIPS 32-bit ARM chip that is better than the industry DSP16-bit processing;
4, real-time acquisition,refresh curve and record test data, a variety of Report print Output;
5, can be used for the retention test (Constant);
6, can be used for products of low cycle (repeatedly) fatigue test;
7, the unit of force values: N, KN, Kgf, Lbf ,unit of length: mm, cm, in freely convertible
II. Control method:
Computer software to set speed, the load fracture (rupture), the running time,especially
with the manual operation box: convenient calibration and fitted to hold the specimen
positioning 
Automatically determine the fracture of materials, when crushing it is automatic shutdown
and automatically return
Curve types: curve longitudinal
The horizontal axis can be arbitrarily set.
The load to displacement;the load to time; displacement to time. 
Stress to strain; strain to time; stress to time. 

III. Specifications:
Maximum force capacity: 100N,200N,500N,1KN,2KN,5KN,10KN,20KN,50KN,
100KN(choose)
http://tonyhk.hk/http://tony0769.com
Page 47 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Force measurement accuracy: 0.5%
Test stroke: 1000mm, effective test width: 400 mm, or specified per customer
Test force loading the measuring range: 0.4% -100% FS
Resolution: maximum test force of 1/200000
Test speed :0.01 - 500mm / min. or specified per customer.
Displacement measurement accuracy: ± 0.5% of indication
Test force control rate adjustment range: 0.05% -5% FS / S
Control accuracy: ± 0.5% when the control rate ≥ 0.05% FS / S,
Net Weight: 150kg, Gross weght:220 kg (after wooden package)
Package wooden box size: 67 x 102 x 193cm
IV. Software Operation Interface
http://tonyhk.hk/http://tony0769.com
Page 48 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
V. Test Result
VI. Report
http://tonyhk.hk/http://tony0769.com
Page 49 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
User Settings
http://tonyhk.hk/http://tony0769.com
Page 50 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Force-elong
http://tonyhk.hk/http://tony0769.com
Page 51 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Multi-Graph
http://tonyhk.hk/http://tony0769.com
Page 52 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Test Result
http://tonyhk.hk/http://tony0769.com
Page 53 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Grips for Fabric and Leather(Grips could be made specified by
customers)
1) Tensile strength ISO 13934-1
2) Tear strength
ISO 13937-2
http://tonyhk.hk/http://tony0769.com
Page 54 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Resistance to seam slippage
ISO 13936-2
http://tonyhk.hk/http://tony0769.com
Page 55 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Some of our strategic partners as follow:
1深圳SGS通标技术服务有限公司
Shenzheng SGS-CSTC Standards Technical Services Co., Ltd
(Physics Lab)
2青岛SGS通标技术服务有限公司
Qingdao SGS-CSTC Standards Technical Services Co., Ltd
(Physics Lab)
3广州SGS通标技术服务有限公司
4越南SGS Vietnam
5韩国SGS Korea
6墨西哥SGS Mexico
7香港SGS HK
8深圳计量研究院
Shenzhen Academy of Metrology & Quality Inspection
(Physics Lab)
(Physics Lab)
(Physics Lab)
(Physics Lab)
(Physics Lab)
(Physics Lab)
9广东清远出入境检验检疫局
Guangdong Entry-Exit Inspection and Quarantine Bureau-Qingyuan Branch
(Physics Lab)
10广东惠州出入境检验检疫局
Guangdong Entry-Exit Inspection
(Physics Lab)
and
Quarantine
Bureau-Huizhou
Branch
11安徽出入境检验检疫局 Anhui Entry-Exit Inspection and Quarantine Bureau
(Physics Lab)
12河北省纤维检验局
Hebei Fiber inspection Bureau
(Physics Lab)
13广西梧州出入境检验检疫局
Guangxi Entry-Exit Inspection and Quarantine Bureau-Wuzhou Branch
14中鼎检测技术服务有限公司
Consumer Testing Technology Co., Ltd (CTT)
15冠准检测技术服务有限公司
Accurate Technology Co.,Ltd(ATC)
16北南检测技术服务有限公司
NSTechnology Co.,Ltd(NST)
17BACL 倍 科 检 测 技 术 服 务 有 限 公 司
Corp.(BACL)
Bay Area Compliance Laboratories
18深圳TUV莱茵检测技术服务有限公司 TUV Rheinland (Shenzhen) Co., Ltd.
19中山力创检测技术服务有限公司
Lctech(DongGuan)Testing Service Co.,Ltd
20华中科技大学工程制造研究院
HUST Manufacturing Engineering Institute
http://tonyhk.hk/http://tony0769.com
Page 56 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
21 重庆市合川计量质量检测中心
22 福建林业研究院
(物理实验室)
Fujian Academy of Forestry Sciences
23新疆出入境检验检疫局
Xinjiang Entry-Exit Inspection and Quarantine Bureau
24敏华控股 Man Wah Holdings Limited
25东莞楷模家居用品有限公司
COOMO
26东莞佳居乐用品有限公司 Dongguan CACAR Kitchen
27深圳雅兰公司(国内卖场展示仪器)Shenzhen Airland Furniture Ltd.
28德国博克BOCK家具(中国、德国) (物理实验室) BOCK Gemany
29 Intertek 天祥中国
30 SGS Pakistan(Private ) Limited
31 PT SGS INDONESIA
32 TUV RHEINLAND VIETNAM CO,.LTD
TUV
33 TUV Rheinland of North America Softlines
34 API Lab Testing Ltd
35 Cotecna Inspection Hong Kong Limited (Toys Testing Lab)
36 Applus(Shanghai) Quality Inspection Co., Ltd (EN71 Toys Testing Lab)
http://tonyhk.hk/http://tony0769.com
Page 57 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Company Profile
Established in 2001 at New Territories of HK and having the sales department at
Dongguan city in 2004. Tony International(HK) Co., LTD is specializes in testing and
measurement industry for toys and textile field.
Continue its advanced design technology and
concept, excellent technology of producing and
outstanding
providing
system of quality management;
the
enterprises
and
the
quality
inspection agencies with high class products. All
products meet the International testing standard. Meanwhile,
we provide customer with complete solutions of laboratory.
Sincerely administration make Tony sales network extend all
over the world. Up to today Tony products spread to
countrywide users.We take pride in having a long list of satisfied
customers, who always look up to us for their various
requirements. Most of our customers are satisfied from our
products and services and as a result of which, we are getting
repeat orders. Some of our important customers, include:
SGS in France,SGS in Vietnam, SGS in China,SGS
inKorea,Intertek in China,SAT
in China,BACL in
Shenzhen, NSF in Shanghai, ITS,BV,TUV etc
The quality proves value, the effort brings success
What you concerning is we are struggling all the time......
http://tonyhk.hk/http://tony0769.com
Page 58 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
http://tonyhk.hk/http://tony0769.com
Page 59 of 60
complete solution of laboratory
Tony International (HK) Co.,Ltd
Show room:
http://tonyhk.hk/http://tony0769.com
Page 60 of 60
complete solution of laboratory