DAELIM NS 125 DLX Owner`s manual

OWNER'S MANUAL
HEAD OFFICE (FACTORY)
#58, SUNG SAN-DONG, CHANG WON, KYUNGNAM, KOREA
TEL : (82-55) 239-7000 FAX : (82-55) 239-7524
OM42-0201-02E
*NS-125DLXO/M02.11.53:40PM페이지1
CONTENTS
SPECIFICATION ................................................................... 3
OPERATION INSTRUCTION ............................................ 4
SAFETY PRECAUTIONS ................................................... 4
PRIOR TO STARTING VEHICLE .......................................... 5
CORRECT ATTIRE ............................................................ 5
OPERATION...................................................................... 6
CARGO............................................................................. 6
MODIFICATION ................................................................. 7
MUFFLER ......................................................................... 7
PARTS LOCATION............................................................. 8
METER READING AND USAGE ....................................... 10
METER ............................................................................. 10
INDICATOR LAMP ............................................................. 10
HOW TO SET CLOCK ........................................................ 11
SWITCH OPERATION ........................................................ 12
MAIN SWITCH ................................................................... 12
STARTER BUTTON............................................................ 12
HEADLIGHT ...................................................................... 13
WINKER SWITCH .............................................................. 13
HORN BUTTON ................................................................. 14
HAZARD SWITCH .............................................................. 14
EQUIPMENT USAGE .......................................................... 14
STEERING LOCK ............................................................... 14
SEAT LOCK ....................................................................... 15
INNER BOX ....................................................................... 15
TRUNK .............................................................................. 16
DOCUMENT STORAGE AREA............................................. 16
BAG HOLDER .................................................................... 17
HANDPHONE CHARGER .................................................... 17
CORRECT DRIVING OPERATION .................................... 18
STARTING THE ENGINE..................................................... 18
IF ENGINE CANNOT BE STARTED ...................................... 20
AFTER STARTING ENGINE................................................. 21
PROPER DRIVING METHODS............................................. 22
STOPPING ........................................................................ 23
SELF INSPECTIONS BEFORE OPERATION .................. 25
INSPECTION OF CONCERNED AREA ................................. 26
BRAKE INSPECTION .......................................................... 26
FUEL CHECK ..................................................................... 27
TIRE INSPECTION ............................................................. 28
ENGINE OIL LEVEL CHECK ................................................ 29
LIGHTS AND WINKER INSPECTION .................................... 29
BACK MIRROR INSPECTION .............................................. 30
1
*NS-125DLXO/M02.11.53:40PM페이지2
FUEL LEAK INSPECTION ................................................
LICENSE PLATE INSPECTION.........................................
MAINTENANCE ...............................................................
MAINTENANCE SCHEDULE ............................................
MAINTENANCE PRECAUTIONS ......................................
BRAKES ........................................................................
BRAKE HOSE, PIPE LEAKAGE, DAMAGE, ASSEMBLY STATE ....
BRAKE PAD WEAR.........................................................
CHANGING ENGINE OIL .................................................
WHEEL REMOVAL .........................................................
SPARK PLUG .................................................................
BATTERY INSPECTION ..................................................
FUSE REPLACEMENT ....................................................
BULB REPLACEMENT ....................................................
AIR CLEANER ELEMENT INSPECTION ...........................
SIDE STAND INSPECTION ..............................................
CABLE RUBBER PART INSPECTION ...............................
NOTABLES FOR CAR WASHING .....................................
STORAGE GUIDE...........................................................
FRAME AND ENGINE NUMBER ...................................
2
30
30
30
31
33
33
35
35
36
37
39
40
41
42
44
45
45
45
46
47
SAFE DRIVING ........................................................................ 48
PREPARATION BEFORE DRIVING............................... 48
DRIVING METHOD............................................................ 49
DRIVING POSITION .......................................................... 49
PRECAUTION WHEN DRIVING ......................................... 51
STARTING ........................................................................ 52
TURNING METHOD .......................................................... 54
PRINCIPLE OF TURN ........................................................ 54
EFFECT OF SPEED .......................................................... 54
3 POSITIONS OF TURNING .............................................. 55
TURNING METHOD .......................................................... 56
PRECAUTION WHEN TURNING ....................................... 57
BRAKING METHOD.......................................................... 58
BASIC PRINCIPLE OF BRAKE(FRICTION FORCE) ............. 58
RESTRAINT OF BRAKE EFFECT (INERTIA) ..................... 58
BRAKING METHOD .......................................................... 59
COMPARISION OF BRAKING DISTANCE .......................... 59
IMPACT WHEN COLLISION .............................................. 59
WIRING DIAGRAM................................................................ 60
*NS-125DLXO/M02.11.53:40PM페이지3
SPECIFICATION
ITEM
DATA
ITEM
DATA
LENGTH×WIDTH×HEIGHT(mm)
1,970×700×1,110
IGNITION SYSTEM
C.D.I
WHEEL BASE(mm)
1,350
BATTERY CAPACITY
12V6AH(MF TYPE)
GROUND CLEARANCE(mm)
130
FUEL CAPACITY(ℓ)
7.5
SEAT HEIGHT(mm)
765
WEIGHT(kgf)
110
PASSENGER
2
ENGINE TYPE
OIL COOLED/AIR COOLED
4 STROKE 4VALVE
TIRE SIZE
SUSPENSION
BRAKE
FR.
120 / 70 - 12 53K
RR.
130 / 70 - 12 62K
FR.
TELESCOPIC
RR.
UNIT SWING OIL DAMPER
FR.
HYDRAULIC DISK
RR.
HYDRAULIC DISK
PISTON DISPLACEMENT(cc)
124.9
BORE AND STROKE(mm)
56×50.7
SPARK PLUG
CR8EH-9
STARTING SYSTEM
START MOTOR / KICK
FUSE(A)
15
TRANSMISSION TYPE
V - MATIC
3
*NS-125DLXO/M02.11.53:40PM페이지4
OPERATION INSTRUCTION
SAFETY PRECAUTIONS
This manual describes matters pertaining to correct operation,
safe operation and simple maintenance of the vehicle you
purchased.
To ensure more comfortable and safer operation,
make sure to read this manual carefully prior to operation.
●The photographs and drawings shown in this manual may
differ from those of actual vehicles due to changes in vehicle
specifications and modifications made.
●This vehicle is designed for 2 riders including the operator.
CAUTION
●Do not use polluted gasoline.
Using polluted gasoline will cause rust inside the fuel
tank, and will close the supply of fuel to the carburetor,
leading to an improper engine starting or may cause
serious damage to an engine.
●Do not use polluted or low-grade oil.
Always use genuine oil to protect and extend vehicle
performance and its life span.
●If any failure occurs due to the use of polluted gasoline
or oil, such failure will be excluded from being eligible
for repairs under the warranty.
4
●Careful driving and the wearing of proper attire and safety
equipment are the most important factors in the safe
operation of the scooter. Please obey traffic regulations and
do not be hurried and careless.
●Many new vehicle owners operate their newly purchased
vehicles with great care and attention to safety factors.
However, after becoming accustomed to the operations are
often discarded, which can lead to accidents. Please don't let
this happen to you and always approach the operation of your
vehicle with the safety considerations needed.
When operating the vehicle, always keep in mind and obey
the notes of precaution printed on the“Safety Precaution
Label”attached to the vehicle.
●Always wear helmet.
●Observe posted speed limits.
●Park vehicle away from people(especially children) as
the muffler can get very hot.
●For safety, do not illegally modify the vehicle.
●If exposed to direct sunlight for a long period of time,
the visual display panel may temporailly be fogged.
●Regularly conduct specified maintenance inspections.
<Maintenance Inspection Points>
Brakes, Tires, Oil, Lights, Horn, Instruments
*NS-125DLXO/M02.11.53:40PM페이지5
PRIOR TO STARTING VEHICLE
●Read user's manual carefully.
●Conduct maintenance checks prior to operation.
●Always maintain vehicle in clean status and carry out
specified maintenance checks.
●Make sure to stop engine and stay away from fire when
fueling.
●Exhaust gas contains harmful substance such as carbon
monoxide, Start engine in well-ventilated places.
A helmet should always be
worn and the helmet chin
strap should be securely
fastened.
Correct shirts or jackets with
tight-fitting sleeves should be
worn,
CORRECT ATTIRE
●Always make sure to wear helmet for safety. Wear gloves
and safety goggles.
●Do not wear uniforms which might hinder operation. It is
dangerous if the uniform is caught by brake lever.
Shoes should fit properly, and shoes having little or
no heel should be worn.
5
*NS-125DLXO/M02.11.53:40PM페이지6
OPERATION
●Operators should naturally fix bodies to keep smooth driving.
●Please check whether or not you are unnaturally strained and
strung up.
●Driving pose has a great influence on safe operation.
Please always maintain the center of your body in the middle
of seat, Especially do not sit at the rear seat because it may
lessen the weight of front wheel and cause trembling steering
wheel.
●Passengers should accurately fix bodies using both hands and
put both feet on floor panel.
CARGO
When carrying cargo, you must keep in mind that operating the
vehicle, especially when turning, will be different.
Make sure not to overload the vehicle with goods as this can
make the vehicle unstable during operation.
REAR CARRIER MAXIMUM LOAD : 3kg
TRUNK MAXIMUM LOAD : 10kg
INNER BOX MAXIMUM LOAD : 1.5kg
6
*NS-125DLXO/M02.11.53:40PM페이지7
MODIFICATION
CAUTION
●Only load cargo in or on designated areas as placing or
fastening cargo to other areas can cause damage to the
vehicle.
●Do not place articles between the frame body cover and
engine as this can burn the goods.
Modification of vehicle structure or function deteriorates
manipulability or causes exhaust noise to become louder
shortening the vehicle life. These modifications are not only
prohibited by law but also are the acts harmful to other people.
Modifications are not covered by warranty.
MUFFLER
●Pay particular attention to fellow passenger so that he/she
can prevent getting burnt by the hot muffler during travel.
7
*NS-125DLXO/M02.11.53:40PM페이지8
PARTS LOCATION
MAIN SWITCH
FUEL TANK
FR. BRAKE LEVER
PARKING LOCK
BAG HOLDER
PILLION STEP
8
BATTERY
*NS-125DLXO/M02.11.53:40PM페이지9
RR.BRAKE LEVER
INNER BOX
LUGGAGE BOX
SEAT LOCK
PILLION STEP
KICK START PEDAL
MAIN STAND
9
*NS-125DLXO/M02.11.53:41PM페이지10
METER READING AND USAGE
ODOMETER
WINKER INDICATOR
METER
INDICATOR LAMP
<SPEEDOMETER>
<WINKER INDICATOR>
Indicates driving speed. Maintain legal
speed limits to ensure safe operation.
If the winker switch is operated,
the winker indicator flashes in union with
the flashing of the turn signals.
FUEL GAUGE
<ODOMETER>
Indicates total distance in kilometers
travelled by the vehicle.
CLOCK
SPEEDOMETER
10
HEADLIGHT
INDICATOR
<CLOCK>
●Current time shows below meter.
●You can use other clock battery.
<FUEL GAUGE>
CAUTION
The fuel gauge indicates the gasoline
level inside the fuel tank.(The needle will
indicate the amount of gasoline in the fuel
tank whether the main switch is turned to
OFF or On position.)
Gasoline should be put in the fuel tank as
soon as possible if the needle is resting in
the red area. When the needle is in the red
area, roughly 1, 2 liters of gasoline can be
put in the vehicle to fill tank.
●Long exposure to sunray can make
clock digit invisible.
<CHANGING CLOCK BATTERY>
●Separate the front handle cover.
●Open the cover of clock battery
below meter and change battery.
●If you feel difficult, please contact
authorized maintenance shops for
inspection.
*NS-125DLXO/M02.11.53:41PM페이지11
HOW TO SET CLOCK
TIME EX)
12 : 30
DATE EX)
A
B
1 21
DATE/TIME CHECKING
A
B
EXAMPLE 1
If you push button A one time,
time will be changed into date.
12 : 30
TIME SETTING
●Push button B 4 times. 12 : P
●Push button A and set time you want.
●If completed, push button B for setting.
MINUTE SETTING
: 30
●Push button B 5 times.
●Push button A and set time you want
●If completed, push button B for setting.
MONTH SETTING
1
●Push button B 2 times.
●Push button A and set time you want.
●If completed, push button B for setting.
DAY SETTING
21
●Push button B 3 times.
●Push button A and set time you want
●If completed, push button B for setting.
1 21
After checking it,
push button B to keep it back.
EXAMPLE 2
If you push button B one time,
time will be changed into date and
automatically restored into time.
12 : 30
1 21
12 : 30
After checking, it, push button B 5 times
to keep it back.
11
*NS-125DLXO/M02.11.53:41PM페이지12
SWITCH OPERATION
MAIN SWITCH
MAIN SWITCH
KEY
1. On.... Starts engine. Key can not be
pulled out.
2. OFF....Stops engine. Key can be
placed in or taken out of the
main switch.
3. LOCK....Locks handle bars. Key can be
placed in or taken out of the
main switch.
12
CAUTION
●Do not manipulate main switch key
during operation. If the main switch
key is placed on“Off” or“Lock”
position, all electrical system will
not function. Never operate the
main switch key during travel as it
might cause unexpected accidents,
If it is necessary to remove the
main switch key, stop the vehicle
first prior to removing.
●When you park the vehicle and
leave it, please lock handle bars and
take out the key.
●If the key is left in“ON”position
without starting engine, battery is
discharged.
●Do not use a number of keys
together with a metal key holder.
The keys and the key holder may
cause scratches or other damage to
the cover while operating the
vehicle.
(Recommend cloth or leather key
holders)
STARTER BUTTON
STARTER BUTTON
The engine is started pressing this button
when pressed in a state where the main
switch key is placed to an ON position and
the brake lever is pulled.
CAUTION
●The engine will not start if the
brake lever is not pulled.
*NS-125DLXO/M02.11.53:41PM페이지13
HEADLIGHT
WINKER SWITCH
<TURNING ON HEADLIGHT>
<HEADLIGHT HIGH/LOW BEAM SWITCH>
Put main switch key in “ON” position and
turn on headlight switch.
High beam or low beam can be operated
by the use of high/low beam switch.
HEADLIGHT HIGH/LOW BEAM SWITCH
HEADLIGHT SWITCH
WINKER SWITCH
HIGH BEAM
D (HI)
SWITCH POSITION
(H)
(P)
(OFF)
FUNCTION
Headlight, taillight,
position lamp and
meter lights on.
Position lamp, taillight,
and meter lights on.
Light turned off.
...... used when needing extra
light.
If this switch is turned on when the main
switch is in an ON position, the winker will
operate.
(R)....used when making a right turn.
(L)....used when making a left turn.
LOW BEAM
D(LO)
...... used when other vehicles are
present, in the city, etc.
CAUTION
●Use the high beam only in the
suburban road or when the usage of
the high beam not hinder the safe
driving of the car ahead.
CAUTION
●The winker switch does not automatically turn back to its original
position after completing the turn.
Please set the switch back to its
center position after turning.
13
*NS-125DLXO/M02.11.53:41PM페이지14
HORN BUTTON
HAZARD SWITCH
EQUIPMENT USAGE
STEERING LOCK
STEERING
LOCK
HORN BUTTON
The horn is sounded if the horn button is
pressed when the main switch is in an ON
position.
KEY
HAZARD SWITCH
When the emergency light button is
pressed with the main switch in “ON”
position, the winker lamp will start
blinking.
<LOCKING>
To lock the steering, turn the handlebars
all the way to the left, turn the key to
LOCK while pushing in. Remove the key.
<UNLOCKING>
To unlock the steering, turn the key to the
OFF position.
WARNING
●Do not turn the key to LOCK while
riding the motorcycle; loss of
vehicle control will result.
14
*NS-125DLXO/M02.11.53:41PM페이지15
INNER BOX
SEAT LOCK
SEAT LOCK
INNER BOX
CAUTION
●Do not place valuable of fragile
goods in the inner box.
●Make sure to remove important
items out of the inner box when
washing the vehicle as water can
enter the inner box.
MAIN SWITCH
MAIN SWITCH
<LOCKING>
●The seat automatically locks when the
seat is pushed in its downward position,
●Lightly pull upward on the seat to make
sure the seat has been properly locked.
<UNLOCKING>
●Turn the seat lock switch to the right
using the main switch key.
<LOCKING>
Turn the inner box switch to the right
using the main switch key. In this state,
close the cover, turn the key to the left and
then remove the key.
<UNLOCKING>
CAUTION
●As the seat automatically locks,
take special care not to accidently
leave the key in the trunk.
●Driving with unlocked seat lock
may cause danger.
Turn the inner box switch to the right with
the main switch key and the inner box will
easily open.
INNER BOX MAXIMUM LOAD: 1.5kg
15
*NS-125DLXO/M02.11.53:41PM페이지16
TRUNK
DOCUMENT STORAGE AREA
TRUNK
SEAT LOCK
●There is a trunk under the seat.
●The seat is opened to gain access to the
trunk by using the main switch key on
the seat lock.
●The lamp inside the trunk will be turned
on if the seat is opened.
TRUNK MAXIMUM LOAD:10kg
16
CAUTION
●Make sure that the seat is securely
locked after closing the seat.
●An unlocked seat can hinder the
operation of the vehicle.
●The temperature inside the trunk
rises due to heat from the engine.
Do not place foodstuffs and other
articles that can be damaged easily
by heat. Also do not place flammable materials in the trunk.
●Do not place valuable or fragile
goods in trunk.
●As water can enter the trunk when
washing, make sure to remove
articles that can be damaged by
water.
●Do not load uncloseable size of
helmet and thing in the trunk,
otherwise, the battery can be
discharged with the trunk lamp on.
DOCUMENT STORAGE AREA
● There is a document storage area on
the bottom of the seat.
● Store the owner’s manual and the
maintenance notebook in this area.
*NS-125DLXO/M02.11.53:41PM페이지17
BAG HOLDER
HANDPHONE CHARGER
HANDPHONE CHARGER
BAG HOLDER
●For ease in carrying bags and similar
items, they should be hung from the bag
holder which is fitted for this purpose.
●When using the bag holder, place it in
the open position and return it to the
normal position when not in use.
CAUTION
●Do not attempt to carry very heavy
or bulky loads since this would
affect the stability and steering
characteristics of the scooter.
●The main switch key is used to open the
inner box.
●Open the charge socket cap, insert the
handphone plug into the socket.
●Close the inner box.
●Turn the main switch to an ON position.
●When the charging is completed, open
the inner box and remove the handphone
plug.
CAUTION
●The charging of the handphone
must be done with the main switch
placed in ON.
●Usage of if the handphone plug for
other purpose (for example, lantern
or ciga jack) may cause the battery
discharging.
●Driving the vehicle during charging
the handphone may cause damage
and failure of the handphone.
17
*NS-125DLXO/M02.11.53:41PM페이지18
CORRECT DRIVING OPERATION
●Make sure to check the oil, gasoline, etc.,
before starting the engine.
●Please ensure that the main stand is in a
down position when starting the engine.
CAUTION
●Make sure that the rear brake is
holded when starting the engine to
prevent an unexpected quick start
of the vehicle.
●Drive with care for both safety reasons
and longer vehicle life.
●For 1 month (or 1,000km) after purchasing the vehicle, drive moderatly
avoiding fast starts and fast acceleration.
18
STARTING THE ENGINE
Always follow the proper starting
procedure described below.
Lock the rear wheel.
●This motorcycle is equipped with a side
stand ignition cut-off system.
●The engine cannot be started if the side
stand is down.
●Always be ensure that you operate the
engine starting controls with the scooter
on its stand.
WARNING
●Never run the engine in an
enclosed area. The exhaust
contains poisonous carbon
monoxide gas that can cause loss
of consciousness and lead to
death.
●While the scooter is on its stand
you should NEVER apply full
throttle:if the rear wheel touches
the ground the scooter would set
off at full speed. (Remember that
the scooter has a centrifugal
automatic speed control)
Turn the main switch to an ON position.
Start engine with cell or kick.
*NS-125DLXO/M02.11.53:41PM페이지19
<USING THE ELECTRIC START(CELL)>
●Press the starter button without rotating
the starter grip (opening the throttle).
●If the engine is hot and does not start
after pressing the starter button for 3~4
seconds, rotate the throttle grip to
1/8~1/4 of a rotation and try again. This
will allow easy starting
1/8
1/4
●It is possible that starting will be more
difficult if the vehicle has not been used
for a long period of time or if the fuel
hole is plugged up(starting problems
even when there is sufficient fuel in the
fuel tank may be an indication of a
plugged fuel hole).
When this happens, do not rotate the
throttle grip and try the starter button a
few times.
CAUTION
CAUTION
●Immediately release the starter
button as soon as the vehicle has
started.
●Do not press the starter button when
the engine is running.
This can damage the starting motor.
●Do not keep the starter button
pressed for more than 5 seconds at
a time. Release the starter button
for approximately 10 seconds
before pressing it again.
19
*NS-125DLXO/M02.11.53:41PM페이지20
<WITHOUT ELECTRIC START(KICK)>
●Erect main stand and hold rear brake
lever and then step kick starter pedal
strongly.
IF ENGINE CANNOT BE STARTED
When the engine is cold (morning or
winter or the vehicle has not been used
for a long period of time) let the engine
idle for a short period allow the engine
to warm up.
CAUTION
●Keep holding rear brake until start.
●Exhaust has contains harmful substance such as carbon monoxide.
Start engine in well-ventilated places.
CAUTION
●Make sure to place kick starter in
its original position after the engine
has been started.
●Be sure to erect main stand and side
stand when starting.
●Do not use the starter button and the
kick-starter pedal simultaneously.
20
If engine cannot be started or vehicle does
not move, check the followings.
●Is there fuel in fuel tank?
●Are you operating in accordance with the
instructions given in owner’s manual?
●Is fuse not cut?
●Is starter motor running?
●If starter motor is not running due to
battery consumption, try starting motor
by using kick start technique.
*NS-125DLXO/M02.11.53:41PM페이지21
AFTER STARTING ENGINE
Fold the main stand.
●Push the vehicle forward to fold the
main stand and make sure that the brake
lever does not become released during
this operation.
Get on the vehicle.
●Mounting should be done from the left
side, and you should sit squarely on the
seat. Leave either one foot or both feet
planted on the ground.
Release the squeezing tension on the
rear brake lever and slowly begin to
rotate the throttle grip to allow for a
slow and easy start.
CAUTION
●A quick rotating of the throttle grip
will cause the vehicle to move
suddenly forward.
CAUTION
●Do not excessively open the throttle
until you actually start the driving
operation of the vehicle.
CAUTION
●Keep holding rear brake lever
before starting.
●If the engine RPM isn’t decreased
after the throttle grip return to its
original position, stop operating
and inspect it in the closest
authorized repair center.
21
*NS-125DLXO/M02.11.53:41PM페이지22
PROPER DRIVING METHODS
●Before entering traffic, use the correct
turn signal to foreward other drivers of
your intentions.
Speed is controlled by the operation of
the throttle grip.
●If the throttle grip is rotated........
The speed of the vehicle increases.
Please rotate the throttle grip slowly.
When climbing a hill, the throttle grip
need to be rotated further to give the
vehicle more power.
●If the throttle grip is allowed to
rotate back........
Work the front and rear brakes together.
●Allow the throttle grip to rotate back to
its beginning position and then squeeze
the brake levers.
●If is best to operate the brakes by first
lightly squeezing the brake levers and
then changing to a more firm squeeze.
RR. BRAKE
FR. BRAKE
Speed decreases. This can be done
slowly or quickly, depending on how
quickly you need to decelerate.
BACK ROTATE
ROTATE
CAUTION
●If only one of the brakes is used, it
is possible for the vehicle to
experience sliding.
22
*NS-125DLXO/M02.11.53:41PM페이지23
The brakes should never be suddenly
applied and the handle bars should
never be suddenly turned.
●Sudden braking or turning can cause the
vehicle to slide and tip over.
●It is especially dangerous to perform
sudden braking on wet roads or in rainy
weather as the tires can lose traction and
slip easily.
Special care in driving should be
taken during rainy weather.
●More braking distance is needed when
driving on wet roads or in the rain.
Reduce speed and be sure to initiate the
braking operation sooner than when
driving in normal conditions.
●On downgrades, allow the throttle grip
to rotate back to its initial position to
reduce speed, and apply the brakes and
drive slowly down the hill.
●It is possible for the brakes to
temporarily lose operative ability after
driving through a puddle or when
driving in the rain. To ensure that the
brakes are operating properly, slow
down(after checking for other vehicles)
and while driving slowly, lightly apply
the brakes to rid the brakes of any
excess water and to dry them.
●Be extremely careful when driving in
the snow or on icy roads.
When driving in these conditions, both
the tires lose much of their traction and
the rear tire can slip when opening the
throttle.
STOPPING
When approaching the desired
stopping area.
●Activate the proper turn signal, and after
checking for other vehicles, slowly turn
into the area in which you want to stop.
●Allow the throttle grip to rotate completely back and apply the front and rear
brakes. The brake light will shine to
alert vehicles in back of you that you are
stopping.
RR. BRAKE
FR. BRAKE
23
*NS-125DLXO/M02.11.53:41PM페이지24
After the vehicle has come to a
complete stop.
Dismount on the left side and lower the
main stand on a flat surface.
●Return the turn signal switch to the
center position and turn the main switch
to OFF. This will turn the engine off.
●Be sure to park in an area that is free of
traffic. Also, the vehicle can tip over if
the main stand is not placed on a stable
and flat surface.
●The main stand is lowered by grasping
the handle bars with the left hand,
holding the rear carrier with the right
hand, and stepping firmly on the stand
with the right foot. In this position, lift
the rear carrier upward, which will
secure the main stand.
24
CAUTION
●Park in a safe area that will not
block traffic. When you parked the
vehicle after driving, make sure
foot the vehicle beyond man’s
reach because engine and muffler
are still hot.
●Park the motorcycle on firm, level
ground to prevent it from failing
over.
●If you must park on a slight incline,
aim the front of the motorcycle
uphill to reduce the possibility of
rolling off the side stand or
overturning.
CAUTION
●Do not rotate the main switch key
while driving. If the main switch is
turned to an OFF or LOCK
position, the electrical system will
not operate. Operating the main
switch key while driving can be
very hazardous. Only turn the main
switch key to OFF or LOCK
positions after completing stopping
the vehicle.
To prevent theft, be sure to lock handle
bars when parking.
4 ST
RO
KE
4 VA
LVE
*NS-125DLXO/M02.11.53:41PM페이지25
SELF INSPECTIONS BEFORE OPERATION
Self inspect the vehicle and have regular
maintenance inspections for increased
safety and the prevention of accidents.
Regular maintenance inspections should
be performed even if the vehicle has not
been used for a long period of time.
Self inspections before operation should be
performed on a daily basis prior to
operating the vehicle.
●Inspections of concerned Area
●Brake inspection
●Fuel check
●Tire inspection
●Engine oil level check
●Lights and turn signal inspection
●Back mirror inspection
●Fuel leak inspection
●License plate inspection
●Throttle grip inspection
CAUTION
Observe safety rules when conducting
inspections.
●Exhaust gas contains harmful
substance such as carbon monoxide. Do not carry out inspections
on vehicle in closed places, or in
poorly ventilated places, with
engine running.
●Conduct inspections on flat, solid
ground with the stand erected.
●Be careful of burns when conducting
inspections immediately after engine
is stopped because the engine and
muffler are hot.
●Stop engine and remove the key
prior to the vehicle maintenance
service.
●Use appropriate types of tools.
●If you are unable to correct trouble
even after you make adjustment or
correction, contact authorized
maintenance shops, dealers or
designated repair shops for
necessary inspection and repairs.
25
*NS-125DLXO/M02.11.53:41PM페이지26
INSPECTION OF CONCERNED AREA
● Check areas which caused for concern
when last operating the vehicle.
● If happened, contact authorized
maintenance shops for necessary
inspection and repairs.
BRAKE INSPECTION
<BRAKE LEVER FREE PLAY>
<CHECK OF BRAKE FLUID>
Lightly squeeze the brake levers until
tension is felt to check for an appropriate
amount of free play. No free play in the
brake levers or overly loose brake levers
are indication of a problem in the brake
system.
This is checked by placing the vehicle on
its main stand on a flat surface. Make sure
that the handle bars are at a horizontal
level. Check to see if the fluid are below
the LOWER level.
If brake fluid are significantly low, this
may indicate that there are leakage in the
brake system. Inspect the brake hoses to
check for leaks.
BRAKE LEVER FREE PLAY: 10-20mm
LOWER LEVEL
FREE PLAY
FREE PLAY
CAUTION
●Specified brake lever free play
must be maintained. Excessive free
play may cause long stopping
distance, brake operational fault
and slow reacting time resulting in
the dangerous situation and
insufficient free play may cause
short stopping distance and damage
brake system(pad, lining, etc.)
26
CAUTION
●If the brake fluid is significantly
lower than the specified level,
inspect not only brake fluid but also
check the front brake pad for wear.
*NS-125DLXO/M02.11.53:41PM페이지27
FUEL CHECK
<CHECK>
<REFUELING>
●Check gasoline to see if there is a
sufficient amount of gasoline to reach
your destination.
●If the fuel gauge needle indicates E
mark (red portion), fill fuel tank with
gasoline as soon as possible.
●Use the main switch key to open the
SEAT.
●Turn the fuel tank cap counterclockwise,
and remove it.
●Fill the tank with gasoline until it
reaches the bottom of the level plate.
●Be sure to set the fuel tank cap to the
right position.
RESERVE FUEL CAPACITY : 1.2ℓ
FUEL GAUGE
FUEL TANK CAP
LEVEL PLATE
CAUTION
●Gasoline is extremely flammable
and is explosive under certain
conditions. Refuel in a wellventilated area.
●Make sure to stop engine and stay
away from fire when refueling.
●Do not fill gasoline past the level
plate. Gasoline may leak out of the
fuel tank when replacing the fuel
tank cap if too much gasoline is put
in the fuel tank.
●Don’t fill low grade gasoline.
Using it can cause damage (bending,
getting worn, etc.) to combustion
chamber and parts of fuel.
●Do not close the fuel cap with
excessive strength. It may cause the
damage of the cap and the rubber
packing resulting in the leak of fuel
and may cause fire in case of
electrical short or the overturn of
the vehicle.
●Avoid repeated or prolonged
contact with skin or breathing of
vapor.
KEEP OUT OF REACH OF CHILDREN.
27
*NS-125DLXO/M02.11.53:41PM페이지28
TIRE INSPECTION
<AIR PRESSURE CHECK>
<CRACKS/DAMAGE>
<FOREIGN MATTER>
Check for an appropriate level of air
pressure by examining how the tire sits on
the ground. If you notice any abnormalities
in the shape of the tire with regard to the
area contacting the ground, use a tire
gauge to check tire pressure and adjust the
tire pressure to the appropriate level.
Check tire tread and sides for cracks and
damage.
Check tire tread and sides for nails, rocks,
etc. That might have become wedged in
the tire.
CRACKS
<TIRE PRESSURE>
120/70-12 53K
130/70-12 62K
1 PERSON FRONT 1.75
AIR PRESSURE RIDING REAR 2.00
(kg/㎠)
2 PERSON FRONT 1.75
RIDING REAR 2.25
SIZE
×
28
FRONT
REAR
×
<TREAD DEPTH>
DAMAGE
<ABNORMAL WEAR>
Check tire tread for signs of abnormal
wear.
●Check the wear indicator (wear limit
marking) to see if there is an insufficient
amount of tread remaining.
●If the indicators are visible, replace tire
with a new one.
WEAR INDICATOR
(WEAR LIMIT MARKING)
ABNORMAL
WEAR
WEAR INDICATOR
LOCATION MARKING
*NS-125DLXO/M02.11.53:41PM페이지29
ENGINE OIL LEVEL CHECK
CAUTION
●If air pressure is inadequate or if there
are cracks, damage or abnormal wear
on tires, it may cause trembling
steering wheel and flat tire.
●Insufficient air pressure may cause
the heavy steering wheel making
handling difficult, fuel over
consumption and the excessive
wear of tire outer area and excessive
air pressure may cause easier
wheel handling and lower fuel
consumption. But it may also cause
the excessive wear of tire center
area.
Check the engine oil level each day before
riding the motorcycle.
The oil level must be maintained between
the upper and lower level marks on the
sight-glass
●Stand the motorcycle on the main stand
on level ground.
●Start the engine and let it idle for
approximately 2~3 minutes.
●Check the engine oil level.
●If required, add the specified oil. Do not
overfill.
LIGHTS AND WINKER INSPECTION
<HEADLIGHT, TAILLIGHT>
Start the engine and make sure the lights
turn on. Also check to see if the lights are
damaged or if there is dirt on them.
<BRAKE LIGHT CHECK>
Turn the main switch to ON.
While separately operating the front and
rear brakes, check to see if the brake light
turns on. Also check to see if there is any
damage to the lens or if there is dirt on the
brake light.
<WINKER CHECK>
●This vehicle is equipped with
tubeless tires. If you have flat tires,
please contact authorised maintenance shops for inspection.
SIGHT GLASS
Turn the main switch to ON.
Check to see if all the winker in the front
and rear of the vehicle(including left and
right sides) are flashing properly, At the
same time, check to make sure that the
automatic sound signal of the winker is
working. Check also to see if any of the
lens are damaged or dirty.
CAUTION
●Running the engine with insufficient
oil may cause serious engine damage.
29
*NS-125DLXO/M02.11.53:41PM페이지30
BACK MIRROR INSPECTION
Sit squarely on the seat and check to see if
you have a good view behind the vehicle
by looking at the back mirrors. Also check
for dirt and damage on the back mirrors.
FUEL LEAK INSPECTION
Check to see if there is any leaking fuel by
thoroughly checking the fuel tank, hose,
carburetor, etc.
CAUTION
●If any fuel is spilled, make sure the
area is dry before starting the
engine.
30
LICENSE PLATE INSPECTION
Check to see if there is any dirt or damage
to the license plate.
Also check to see if the license plate is
firmly secured to the vehicle.
MAINTENANCE
●The Required Maintenance Schedule
specifies how often you should have
your motorcycle served, and what things
need attention.
●It is essential that your motorcycle be
served as scheduled to retain its high
level of safety, dependability, and
emission control performance.
●These instructions are based on the
assumption that the motorcycle will be
used exclusively for its designed
purpose. Sustained high speed
operation, or operation in unusually wet
or dusty conditions, will require more
frequent service than specified in the
MAINTENANCE SCHEDULE.
Consult your authorized Daelim dealer
for recommendations applicable to your
individual needs and use.
*NS-125DLXO/M02.11.53:41PM페이지31
MAINTENANCE SCHEDULE
Perform the Self Inspections Before Operation at each scheduled maintenance period.
I: INSPECT AND, CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY
R: REPLACE L: LUBRICATE C: CLEAN
ODOMETER READING(CAUTION 1)
FREQUENCY
×1,000Km
ITEM
1
MONTH
4
8
12
6
12
18
★
FUEL LINE
I
I
I
I
★
FUEL FILTER
R
R
R
R
★
THROTTLE OPERATION
I
I
I
I
Every 1,000Km : C
AIR CLEANER
SPARK PLUG
NOTE( 2)
I
R
I
★
VALVE CLEARANCE
I
I
I
I
★
CARBURETOR IDLE
I
I
I
I
★
ENGINE OIL
R
R
R
R
ENGINE OIL FILTER
R
R
R
R
C
C
C
★★
OIL FILTER SCREEN
TRANSMISSION OIL
★
BRAKE FLUID
I
I
REMARK
R
NOTE( 3)
I
NOTE( 3)
31
*NS-125DLXO/M02.11.53:41PM페이지32
ODOMETER READING(CAUTION 1)
FREQUENCY
ITEM
★
×1,000Km
1
MONTH
4
8
12
6
12
18
BRAKE SHOE / PAD WEAR
I
I
I
I
BRAKE SYSTEM
I
I
I
I
I
I
I
I
I
I
I
I
I
★
BRAKE STOP SWITCH
★
HEADLIGHT ADJUSTMENT
★
SUSPENSION
★
BOLTS, NUTS, FASTENERS
★★
WHEELS / TIRES
★★
STEERING HANDLE BEARING
★★
I
I
I
I
I
I
I
I
I
DRIVE BELT
I
I
I
★★
WEIGHT ROLLER
I
I
I
★★
SLIDE PIECE
I
I
I
I
REMARK
★ If you do not have the appropriate tools or information to conduct maintenance, or if you feel you are not capable to perform
maintenance on this vehicle, contact authorized dealers or repair shops for maintenance and repairs.
★★To ensure safety, inspections and maintenance of these parts must be carried out by dealers, or repair centers.
NOTES : (1) At higher odometer readings, repeat at the frequency interval established here.
(2) Service more frequently when riding in unusually wet or dusty areas.
(3) Replace every 2 years, or at indicated odometer interval, whichever comes first. Replacement requires mechanical skill.
32
*NS-125DLXO/M02.11.53:41PM페이지33
MAINTENANCE PRECAUTIONS
The following is an explanation of correct
inspection methods, cleaning and parts
replacing. Please always refer to this
section when wanting to inspect or repair
your vehicle.
WARNING
●If your motorcycle is overturned or
involved in a collision, inspect
control levers, cables, brake hoses,
calipers, accessories, and other vital
parts for damage. Do not ride the
motorcycle if damage impairs safe
operation. Have your authorized
Daelim dealer inspect the major
components, including frame,
suspension and steering parts, for
misalignment and damage that you
may not be able to detect.
●Use new, genuine Daelim parts or
their equivalent for maintenance
and repair. Parts which are not of
equivalent quality may impair the
safety of your motorcycle and the
effective operation of the emission
control systems.
BRAKES
CAUTION
●Always observe safety rules when
performing maintenance on the
vehicle.
●Choose a flat surface and make
sure the main stand is in a secure
down position.
●Use correct tools.
●Conduct engine maintenance with
the engine key out of the ignition.
●Be careful around the engine and
muffler when performing maintenance as these areas can become
extremely hot.
●After self maintenance, the waste
material must be packed in the
specified container and entrusted
disposal to the authorized disposal
company.
Both the front and rear brakes are the
hydraulic disk type.
As the brake pads wear, the brake fluid
level drops.
There are no adjustments to perform, but
fluid level and pad wear must be inspected
periodically.
The system must be inspected frequently
to ensure there are no fluid leaks.
If the lever free play becomes excessive
and the brake pads are not worn beyond
the recommended limit, there is probably
air in the brake system and it must be bled.
See your authorized Daelim dealer for this
service.
CAUTION
●Brake fluid may cause irritation.
Avoid contact with skin or eyes. In
case of contact, flush throughly with
water and can a doctor if your eyes
were exposed.
●Keep out of reach of children.
33
*NS-125DLXO/M02.11.53:41PM페이지34
<REPLENISHING FRONT BRAKE FLUID>
●Check that the fluid level is above the
LOWER level mark with the motorcycle
in an upright position.
●Brake fluid must be added to the
reservoir whenever the fluid level
begins to reach the LOWER level mark.
1.Remove the screw rivet and take the
front brake fluid maintenance lid off.
2.Clean dust and other foreign materials
around reserve tank to prevent foreign
materials from falling inside tank.
3.Remove the screws and take oil cup cap,
diaphragm plate, diaphragm off.
4.Replenish recommended brake oil to the
upper level inside reserve tank.
RECOMMENDED BRAKE OIL IS
DOT 3 or DOT 4
5.Reinstall the diaphragm plate, and oil
cup cap.
6.Tighten the screws securely.
7.Install the front brake fluid maintenance
lid.
34
SCREW RIVET
SCREW
BRAKE FLUID
MAINTENANCE LID
OIL CUP CAP
DIAPHRAGM PLATE
DIAPHRAGM
<REPLENISHING RERE BRAKE FLUID>
●Replenish in the same method as that of
front brake fluid replenishment.
CAUTION
●When adding brake fluid, be very
careful not to allow foreign matter
to enter the reserve tank.
●Do not fill past upper level.
This can cause brake fluid to leak
out of the reserve tank.
●Do not let brake fluid contact
vehicle parts as this damages
painted areas. If oil contacts parts,
quickly clean the fluid off using a
dry cloth.
●Use recommended brake fluid as
other types can undergo chemical
changes.
●If brake fluid is exceedingly low,
this can be indication of damage to
the brake system.
●A leak in the brake system can lead
to reduced braking efficiency and
possible loss of braking ability.
*NS-125DLXO/M02.11.53:41PM페이지35
BRAKE HOSE, PIPE LEAKAGE,
DAMAGE, ASSEMBLY STATE
Visually check for fluid leaks or damage
and, using a spanner, check joints and
clamps for clearance.
Also, check hose and pipe protective parts
to see if they contact other parts when
turning the handle bars or due to vibration
when driving.
BRAKE PAD WEAR
Brake pad wear depends upon the severity
of usage, the type of riding, and road
conditions. (Generally, the pads will wear
faster on wet and dirty roads.)
Inspect the pads at each regular
maintenance interval (page 32).
<FRONT BRAKE>
CUTOUTS
[FRONT / REAR BRAKE]
●Check the cutout in each pad.
●If either pad is worn to the cutout,
replace both pads as a set
●See your authorized Daelim dealer for
this service.
<REAR BRAKE>
CUTOUTS
35
*NS-125DLXO/M02.11.53:41PM페이지36
CHANGING ENGINE OIL
If engine oil is polluted, it seriously affects
the engine life span. Maintain appropriate
level of oil, use correct type of oil and
observe oil exchange period.
●Stand vehicle on the main stand on level
ground and run engine idle(warm-up)
for approximately 2-3 minutes.
●Stop engine and place a container under
the engine. Remove the drain plug bolt,
and drain engine oil.
●Tighten the drain plug bolt.
●Remove the plug maintenance cover and
fill the engine oil after opening oil filter
cap of cylinder head cover.
<RECOMMENDED OIL>
If oil sold on markets or privately manufactured oil (oil-grade) is used, engine
life is adversely affected, and the privilege
of warranty repairs cannot be guaranteed.
GRADE(SE, SF, SH)
ℓ(After oil filter change)
OIL CAPACITY : 0.8ℓ
ℓ(After oil change)
0.75ℓ
●Start the engine and keep it idle for a
few minutes.
●Stop the engine and check the oil level.
If the oil level is low, add the
recommended engine oil.
●Check on oil leaks.
36
SIGHT GLASS
DRAIN PLUG BOLT
CAUTION
●If you change engine oil immediately after engine is stopped, be
careful of burns because the engine,
muffler and engine oil are still hot.
●Exercise caution not to allow dust
or other foreign matter to flow in
when refilling engine oil.
●If oil overflows, wipe off oil clean.
If oil level is lower or higher than
prescribed level, engine is adversely affected.
●Do not mix oil with those of
different manufacturers or grade, or
do not use low-quality oil as it may
cause deterioration of oil, leading
to accidents.
●Clean the oil filter screen with fresh
cleaning oil every 4,000km.
●Be careful not to lose the oil filter
screen spring when assembling the
oil drain bolt.
*NS-125DLXO/M02.11.53:41PM페이지37
WHEEL REMOVAL
[FRONT WHEEL REMOVAL]
① Raise the front wheel off the ground by
placing a support block under the
engine.
② Loosen the oval screw and remove the
speedometer cable.
④ Loosen the axle nut.
⑤ Withdraw the front wheel axle and
remove the front wheel.
DEPRESSED PART
FIXING BOLTS
AXLE NUT
FRONT CALIPER
OVAL
SCREW
SPEEDOMETER
CABLE
③ Remove the front caliper assembly
from the front fork by removing the
fixing bolts.
CAUTION
●Do not operate brake lever after the
front wheel is removed. It will
make wheel assembling difficult.
FRONT
WHEEL AXLE
⑥ Install in the reverse order of removal.
CAUTION
●When installing the wheel, carefully fit the left brake disk between
the brake pads to avoid damaging
the pads.
Prior to assembling, match the depressed
part( ) of the speedometer gear box with
the projected part of the left front fork.
Fit the caliper over the disc, taking care
not to damage the brake pads. Install the
caliper fixing bolts, and tighten to a
·m
torque of : 2.7kgf·
Tighten the front axle nut to the specified
torque.
FRONT AXLE NUT TORQUE
·m
: 5.0~7.0kgf·
⑦ After assembling, operate brake for a
number of times and see if wheel is
turning smoothly without getting
interruption.
37
*NS-125DLXO/M02.11.53:41PM페이지38
<REAR WHEEL REMOVAL>
FIXING BOLTS
CAUTION
●If a torque wrench was not used for
installation, see your authorized
dealer as soon as possible to verify
proper assembly.
Improper assembly may lead to loss
of braking capacity.
① Set vehicle on main stand in upright
position on level ground.
② Loosen the rear brake hose setting bolt.
③ Loosen the 3muffler setting bolts, and
remove the muffler.
REAR BRAKE HOSE
SETTING BOLT
REAR CALIPER
REAR BRAKE HOSE
SETTING BOLT
FIXING BOLTS
AXLE NUT
REAR SWING ARM
⑧ Install in the reverse order of removal.
REAR AXLE NUT TORQUE
·m
: 6.0~8.0kgf·
CAUTION
MUFFLER
MUFFLER SETTING BOLTS
④ Loosen the rear brake hose setting bolt.
⑤ Remove the rear caliper assembly from
the rear swing arm by removing the 2
fixing bolts.
⑥ Loosen the axle nut, remove the rear
swing arm.
⑦ Remove the collar and the rear wheel.
38
●If a torque wrench was not used for
installation, see your authorized
dealer as soon as possible to verify
proper assembly.
Improper assembly may lead to loss
of braking capacity.
*NS-125DLXO/M02.11.53:41PM페이지39
SPARK PLUG
If electrode is stained or clearance is not
right, satisfactory spark is not produced.
Clean and make adjustment.
●Remove spark plug cap.
●Clean around the plug.
●Using a plug wrench, remove plug.
●Clean plug with plug cleaner.
●Check electrode for wear and corrosion.
●Measure clearance using a feeler gauge.
PLUG GAP: 0.8-0.9mm
●Tighten with hands until the plug
washer touches cylinder head.
<DEALING WITH POOR STARTING>
If plug is reused, turn 1/3~1/4 and tighten.
CAUTION
●If plug of different maker or different
heat value is used, it causes
unsatisfactory engine starting,
inadequate engine revolution and
output deterioration.
●The spark plug must be securely
tightened. An improperly tightened
plug can become very hot and
possibly damage the engine.
When the starter doesn’t work during
driving in winter times or in a repeated
short distance, use the suitable spark plug
for this driving condition.
Poor starting may happen when nonstop
driving in low speed, even though we
produce standard plug.
In case starter isn’t working well in driving
repeatedly in a short distance or in an area
with many traffic signals, use the CR7EH9 pulg instead of standard plug CR8EH-9
STANDARD PLUG: CR8EH-9
●If new plug is installed, turn 1/2 and
tighten using a plug wrench.
PLUG GAP
39
*NS-125DLXO/M02.11.53:41PM페이지40
BATTERY INSPECTION
<CLEANING BATTERY TERMINALS>
●If you remove two screws from battery
box cover after putting floor panel met
forward, you will find battery assembled.
●If the battery terminal is polluted, or in
rust, separate battery and clean it.
●Battery terminal in rust with white
powder should be cleaned with warm
water.
●In case of serious rust of battery terminal, disassemble the battery cord and
grind it with wirebrush or sandpaper.
BATTERY COVER
40
CAUTION
●Turn the ignition switch OFF
before disconnecting the terminal
from the battery. Remove the
negative pole
side cord first and
the positive pole
side cord next.
Make sure, at this time, that
side cord is connected first,
followed by
side cord.
●When handling the battery stay
away from flammable materials.
●Make sure that terminals do not
contact with other adjacent parts
when handling
/
terminal.
Contact with other parts may cause
spark resulting in electrical equipment malfunction, fire and electric
shock.
●Frequent cell starting can shorten
the battery lifetime. Please use a
kick to start the engine after the
long period storage and in case of
the initial starting and the cold
starting to improve starting
performance and extend the battery
lifetime.
<REPLENISHING BATTERY WATER>
●This vehicle doesn’t need either
replenishing or checking battery water
because of the equipment of enclosed
MF battery.
●In case battery needs a checking, it
should be cared of by service center.
CAUTION
●Be careful not to disassemble injection part of enclosed battery.
●When not using vehicle during a
long time, take off the battery from
the vehicle to keep from selfdischarge and electric discharge.
Put the battery in a well ventilated
place after charging fully. In case it
isn’t available to take battery off
from the vehicle, disconnect “-”
terminal.
*NS-125DLXO/M02.11.53:41PM페이지41
FUSE REPLACEMENT
Turn off the main switch to see if the fuse
is severed. If the fuse is severed, exchange
the fuse into 7A fuse.
BATTERY COVER
●To change a fuse, first take off battery
cover. Then, disconnect a “fuse
connector” after opening a “fuse
holder.”
●If the fuse immediately becomes
severed after being changed with the
new one, check another problem of the
electric system.
<DISASSEMBLY>
CORD
FUSE CONNECTOR
<ASSEMBLY>
CAUTION
●Disassembly.
When disassemble fuse, make sure
that fuse holder isn’t separated.
●Assembly.
After assembling fuse in the part of
connector, check if fuse moves
easily to a line. If fuse moves easily, it may cause an accident at
heating.
●Do not use a fuse having a larger
voltage as the wire can become
overheated and damaged.
When replacing any of the electrical parts (lights and gauges), be
sure to replace them with the recommended parts. Using different
parts can lead to the fuses burning
out or damage to the battery.
●When washing the vehicle, take
special care not to allow to be
splashed in the area of the fuses.
41
*NS-125DLXO/M02.11.53:41PM페이지42
BULB REPLACEMENT
●Be sure to turn the ignition switch
OFF when replacing the bulb.
●Do not use bulbs other than that
specified.
●After installing a new bulb, check that
the light operates properly.
CAUTION
●The light bulb becomes very hot
while the light is ON, and remain
hot for a while after it is turned
OFF. Be sure to let it cool down
before servicing.
●Do not put finger prints on the
headlight bulb, as they may create
hot spots on the bulb and cause it to
break. Wear clean gloves while
replacing the bulb.
If you touch the bulb with your
bare hands, clean it with a cloth
moistened with alcohol to prevent
its early failure.
42
[HEADLIGHT BULB]
●Before replacing the bulb, be sure to
check the switches for loose
connection of the connector.
① Loosen the special screw and remove
the front cover.
② Loosen the 4 headlight setting bolts
and pull off the socket without turning.
③ Remove the rubber cover.
④ Remove the pin.
⑤ Slightly press down on the bulb and
turn it counterclockwise.
⑥ Install a new bulb in the reverse order
of removal.
HEADLIGHT BULB : 12V35/35W
RUBBER COVER
HEADLIGHT
FRONT COVER
HEAD LIGHT
BULB
*NS-125DLXO/M02.11.53:41PM페이지43
[TAIL/STOPLIGHT BULB]
[WINKER BULB]
① Remove the rear undercover.
② Loosen the 2 screws and remove the
rear combination light lens.
③ Slightly press down on the bulb and
turn it counterclockwise.
④ Install a new bulb in the reverse order
of removal.
<FRONT WINKER BULB>
TAIL/STOP LIGHT BULB : 12V 21W/5W
REAR COMBINATION
LIGHT LENS
① Remove the RH./LH. back mirrior.
② Loosen the 1 RH./LH. handle side
cover lower screw, and 1 each of the
special upper side screws.
③ Loosen the 4 rear handle cover screws.
④ Loosen the front handle cover setting
screw.
⑤ Pull the front handle cover foward, and
remove the wiring.
⑥ Remove the front handle cover.
⑦ Loosen the screw and remove the
socket.
⑧ Slightly press down on the bulb and
turn it counterclockwise.
⑨ Install a new bulb in the reverse order
of removal.
FRONT WINKER BULB : 12V 10W
FRONT HANDLE
COVER
RH. BACK MIRRIOR
BULB
REAR UNDERCOVER
BULB
RH. HANDIE
SIDE COVER
FRONT HANDLE
COVER
SCREW
SOCKET
LH. BACK
MIRRIOR
LH. HANDLE
SIDE COVER
43
*NS-125DLXO/M02.11.53:41PM페이지44
AIR CLEANER ELEMENT
INSPECTION
<REAR WINKER BULB>
<REMOVAL>
① Remove the rear undercover.
② Loosen the 2 screws and remove the
rear combination light lens.
③ Remove the rear winker lens.
④ Slightly press down on the bulb and
turn it counterclockwise.
⑤ Install a new bulb in the reverse order
of removal.
REAR WINKER BULB : 12V 10W
REAR COMBINATION
LIGHT LENS
REAR WINKER
LENS
① Turn the seat lock switch to the right
using the main switch key.
② Loosen the 6 washer screw and remove
the air cleaner case cover.
③ Loosen the 2 washer screw and remove
the air cleaner element holder.
④ Remove the air cleaner element.
<CLEANING>
●Clean the air cleaner element in clean
oil, squeeze excess oil, and then, wrapping it in a dry cloth, squeeze it again.
●Make sure all excess oil removed and
reassemble the air cleaner element.
OIL : SAE 10W-30
BULB
44
REAR UNDERCOVER
⑤ Install in the reverse order of removal.
CAUTION
●Do not use gasoline or ther materials having a low ignition point
as this can be a fire hazard.
●If the air cleaner element is in
adequately assembled, dust and
other waste materials can directly
enter the engine. This results in
increased cylinder wear and reduced power, and reduced durability
of the engine.
●When washing the vehicle, be
careful not to allow water to get
into the air cleaner.
Difficulties in starting the engine
may result if this happens.
●If the engine start is failed during
rain or after driving across water
pool, check to see if the water is
infiltrated in the air cleaner and
clean it.
*NS-125DLXO/M02.11.53:41PM페이지45
SIDE STAND INSPECTION
●Erect main stand and place vehicle in
upright position on level ground.
●Check the spring for damage or loss of
tension and the side stand assembly for
freedom of movement.
●Check the side stand ignition cut-off
system;
Put the side stand up.
Start the engine.
Lower the side stand. The engine
should stop as you put the side stand
down.
CABLE RUBBER PART INSPECTION
A rubber part is assembled on the cable to
protect the inner cable.
Make sure that this part is placed firmly
around the correct part of the cable. When
washing the car, do not directly spray
water on to the rubber part is dirty, use a
dry cloth to clean this area.
INSPECTION
PART
RUBBER
INSPECTION
PART
●If the side stand system does not operate
as described, inspect it in the closest
authorized repair center.
SIDE STAND
SPRING
CAUTION
●Infiltration of the foreign materials
or water caused by damage of
lever(disengagement, tearing, etc.)
may cause freezing in winter
season resulting in faulty operation,
sudden accelation and braking
force decrease. If any damage is
found, replace with the new one
immediately.
NOTABLES FOR CAR WASHING
●Make sure to stop the engine prior to car
washing.
●Be careful not to allow water to enter
the muffler during the washing.
Water inside the muffler may cause an
improper engine starting or rust occurrence.
●Do not let water get inside the braking
system during the washing, as water
inside the brake system may weaken the
braking power. Upon completion of
washing, select a safe place where there
is no traffic obstruction, and start the
vehicle.
Lightly apply the brake while driving at
a slow speed and check the braking
power.
If the braking power has been weakened, apply brake lightly while driving
at a slow speed to dry up the brake
system.
●Take precautions when waxing the
vehicle.
Excessive polish of the painted section
and/or the resin part with compound
wax might damage the painted section
causing discoloration of the affected
area.
45
*NS-125DLXO/M02.11.53:41PM페이지46
STORAGE GUIDE
Extended storage, such as for winter,
requires that you take certain steps to
reduce the effects of deterioration from
non-use of the motorcycle.
In addition, necessary repairs should be
made BEFORE storing the motorcycle;
otherwise, these repairs may be forgotten
by the time the motorcycle is removed
from storage.
<STORAGE>
●Empty the fuel tank into an approved
gasoline container using a commercially
available hand siphon or an equivalent
method.
●If storage will last more than one month,
carburetor draining is very important, to
assure proper performance after storage.
46
CAUTION
●Gasoline is extremely flammable and
is explosive under certain
conditions. Perform this operation
in a well-ventilated area with the
engine stopped. Do not smoke or
allow flames or sparks in the area
where gasoline is drained or stored
and where the fuel tank is refueled.
●Remove the battery. Store in an area
protected from freezing temperatures
and direct sunlight.
Slow charge the battery once a month.
●Wash and dry the motorcycle. Wax all
painted surfaces.
●Inflate the tires to their recommended
pressures. Place the motorcycle on
blocks to raise both tires off the ground.
●Cover the motorcycle (don’t use plastic
or other coated materials) and store in
an unheated area, free of dampness with
a minimum of daily temperature
variation. Do not store the motorcycle in
direct sunlight.
<REMOVAL FROM STORAGE>
●Uncover and clean the motorcycle.
●Charge the battery as required. Install
the battery.
●Perform all Self Inspections Before
Operation checks (page 25).
Test ride the motorcycle at low speeds
in a safe riding area away from traffic.
*NS-125DLXO/M02.11.53:41PM페이지47
FRAME AND ENGINE NUMBER
●The frame number is stamped on the
front central part of the frame.
●The engine number is stamped on the
central part of the left crankcase.
●The frame and engine numbers will be
used as the basis of recovering the
vehicle when is stolen.
●Record the frame and engine numbers
along with the vehicle license plate
numbers and keep them separately from
the vehicle.
<FRAME NUMBER>
FRAME
NUMBER
NUMBERING CAP
INNER BOX
<ENGINE NUMBER>
ENGINE
NUMBER
SG125E
5000001
LEFT CRANKCASE
47
*NS125DLX(48~64)02.11.53:47PM페이지48
PREPARATION BEFORE DRIVING
SAFE DRIVING
● Performing daily inspection
● Putting on the protective gears (Helmet, glove, goggles, etc.)
● Bringing the driver's licence
G
ORMIN
PERF AILY
D
CTION
INSPE
R'S
DRIVE CE
N
E
IC
L
48
PR FUEL
OT
,
E
GE CTIV
AR
E
S
● Determinating the path to the desired destination
*NS125DLX(48~64)02.11.53:47PM페이지49
DRIVING METHOD
DRIVING POSITION
< SCOOTER >
The appropriate driving position is most important thing to
driving safely.
① Eyes : Look at the front direction widely.
② Shoulders : Relieve the tension.
③ Arms : Relieve the tension and bend arms to inside and let
them act as the spring.
④ Hands : Grip the handle the position away from the inside
end of the handle with distance of one finger to facilitate
the operation of the switch and lever.
⑤ Wrist : Keep the state to act freely without applying
excessive force to the shoulder and arms.
⑥ Knees : Relieve the tension and keep the distance of both
knee same as shoulders.
⑦ Feet : Place the feet to face the front parallel and keep the
distance of both feet same as shoulders
49
*NS125DLX(48~64)02.11.53:47PM페이지50
< VEHICLE EXCEPT SCOOTER >
① Eyes : Look at the front direction widely.
② Shoulders : Relieve the tension.
③ Arms : Relieve the tension and bend arms to inside and let
them act as the spring.
④ Hands : Grip the handle the position away from the inside
end of the handle with distance of one finger to facilitate the
operation of the switch and lever.
⑤ Wrist : Keep the state to act freely without applying excessive
force to the shoulder and arms.
⑥ Knees : Press the fuel tank slightly.
⑦ Feet : Place the feet to face the front parallel and make the
step bar be placed in the center of feet.
50
*NS125DLX(48~64)02.11.53:47PM페이지51
PRECAUTION WHEN DRIVING
●
●
●
●
●
●
●
●
Secure the safe distance.
Drive protectively.
Do not obstruct the traffic.
Do not drive on the pedestrian way or walkway.
Drive on the left driveway when passing away.
Make sure that you can apply the brake anytime.
Always apply the brake when stopping temporarily.
Do not drive excessively long distance and take enough
break.
● If any abnormality is found, stop driving and contact service
center to inspect the vehicle.
● Restart the vehicle after 2~3 min when it is turned over.
● Always turn on the headlight at night.
51
*NS125DLX(48~64)02.11.53:47PM페이지52
STARTING
Prior to starting always look around to avoid accident.
< SCOOTER >
①
②
③
④
⑤
Lock the rear brake with the main stand erected.
Start the engine using the cell or kick.
Pull back the main stand.
Get on the vehicle.
Release the brake lock lever by pull the rear brake lever
strongly.
⑥ Start driving slowly after turning on the winker and
releasing the brake while ensuring the safety around the
vehicle.
52
*NS125DLX(48~64)02.11.53:48PM페이지53
< VEHICLE EXCEPT SCOOTER >
① Get on the vehicle after pulling back the stand.
② Start driving slowly after turning on the winker and
releasing the brake while ensuring the safety around the
vehicle.
CAUTION
●Return the side stand to its original position.
●Keep driving without doing this may cause turnover
accident.
53
*NS125DLX(48~64)02.11.53:48PM페이지54
TURNING METHOD
PRINCIPLE OF TURN
EFFECT OF SPEED
CENTRIFUGAL
FORCE
GRAVITY
The basic principle of turn is balancing using the centrifugal
force which makes vehicle go outside and the gravity which
makes vehicle fall inside.
54
The centrifugal force increases in inverse portion to the radius
of a curve and in portion to the square speed. Decelerate prior
to entering the curved way to reduce the centrifugal force.
*NS125DLX(48~64)02.11.53:48PM페이지55
3 POSITIONS OF TURNING
The basic principle of turn is balancing using combined force of
the centrifugal force and the gravity.
All 3 positions require straightening the head and keeping the
eyes horizontally.
< LEAN-WITH >
This is a turning position with motor cycle and driver in a line.
This position is the most natural and exact, so driver must learn
it thoroughly.
< LEAN-IN >
This is a turning position with driver leaned inside more than
motor cycle. This position is adequate to drive on the rained or
slippy road because it has best road holding.
However, special attention is required because front visual field
is poor when driver leans inside more than motor cycle.
55
*NS125DLX(48~64)02.11.53:48PM페이지56
TURNING METHOD
< LEAN-OUT >
This is a turning position with motor cycle leaned inside
more than driver, which is opposite to the lean-in position.
With this position, quick turn is well performed and driver can
obtain wide front visual field adequate to drive on the rained or
slippy road because it has best road holding. However, special
attention is required because there is danger of slipping on the
bad holding road.
① Turn the throttle grip to its original position and decelerate
using both front and rear brakes.
② Lean the vehicle toward inside of turn circle while driving
slowly at constant speed.
③ Accelerate gradually.
56
*NS125DLX(48~64)02.11.53:48PM페이지57
PRECAUTION WHEN TURNING
Do not drive inside of large truck's turn circle.
< DISTANCE BETWEEN THE FRONT AND REAR WHEEL TURN >
< DEAD ANGLE ZONE >
It is distance between path of the front and rear wheel and
increases in proportion to the length of the vehicle
Dead angle zone is the sight range which cannot be identified by
driver and increases in proportion to the width of the vehicle
57
*NS125DLX(48~64)02.11.53:48PM페이지58
BRAKING METHOD
BASIC PRINCIPLE OF BRAKE (FRICTION FORCE)
RESTRAINT OF BRAKE EFFECT (INERTIA)
● Vehicle is braked using friction between road surface and
tires.
● Braking distance increases 1.5 times on wet road and 3
times on icy road because friction force of road surface is
decreased.
Due to the inertia, vehicle does not stop immediately after
applying the brake.
58
*NS125DLX(48~64)02.11.53:48PM페이지59
BRAKING METHOD
● Turn the throttle grip to its original position and decelerate
IMPACT WHEN COLLISION
Learn the proper braking method to prevent accident.
using the engine brake.
● Erect the vehicle straight.
● Brake using both front and rear brakes.
COMPARISION OF BRAKING DISTANCE
·Vehicle speed : 50 km/h
Impact increases in proportion to the speed and weight. The
impact when collision to concrete wall at 50 km/h is same
as one when falling from the height of 10m.
59
*NS125DLX(48~64)02.11.53:48PM페이지60
WIRING DIAGRAM
START SW.
LIGHTING SW.
CDI UNIT
COMBINATION SW.
RR.STOP SW.
RE
HL
TL
BAT
P
Br
/W
BR
B
E
ST
G
Y/
R
CHARGE SOCKET
B
B G/Y
FUEL UNIT
IGN. COIL
HORN
E HO BAT IG
FR.STOP SW.
G
B/
Y
G
R B/ W
B
SIDE STAND S/W
G/Y
G/Y
L / Y/
G
W W
G/Y
B
B
G/Y
G/Y
B
B
G
B
L/
G
G
B/
W
G
G
G
SB
ENGINE
3P
MINI
BAT.
TR/L
R B /W
B
B
L/ Y/
W WG
4P
G
2P
MINI
TRUNK LAMP S/W
B/ G/ L/ G B/
R W Y
Y
G B/W
R
B
SB
G
R B/ W
B
G B/W
B
G
R.H FR. WINKER LIGHT
G
12V 10W
B
R
G B/W
SB
G
R.H WINKER PILOT
12V 3.4W
TRUNK LAMP
14V 1.4W
G
2P
MINI
SB
G
R
G
R.H RR. WINKER LIGHT
12V 10W
B
B
P
Br
G
P
LG
6P
G/Y
Br
G
METER ILLUMINATION
12V 1.7W x 2
LG
SB
G/Y
Br
G
/
Y
G
G
G
BR
BR
O
SB
6P
MINI
Br
G
/
Y
G
O
STOP AND TAIL LIGHT
12V 21W/5W
L/W
Y/W
FUEL METER
B
G
HIGH BEAM PILOT
12V 1.7W
Y/R
Y/R
L/W
L
L/W
6P
MINI
Y/W
Y/W
SB
SB
O
O
G
O
R
O
L.H RR. WINKER LIGHT
G
L.H WINKER PILOT
12V 3.4W
12V 10W
FUSE 15A
G
L.H FR. WINKER LIGHT
12V 10W
Y
Y
O
O
2P
MINI
G
O
G
B/
R
Y
Y
Y
G/W
L/Y
Y
G/W
L/Y
R
LICENCE LIGHT
12V 5W
P
Y
Y
4P
B/
R
L
RH. HEAD LIGHT
Y
Y
G/Y
Y/R
R
G
G/Y
Y/R
R
G
W
12V 35/35W
G
AUTO
B/S
G
L
BR
12V 5W
L
W
P
POSITION LIGHT
W
BR
4P
BR
G
G
Y Y Y G B R
L
G B Gr
L Br/W
W
SB
O
Gr
B
SB
LG
O
Gr
6P
LH. HEAD LIGHT
W
12V 35/35W
G
POSITION LIGHT
LO HI HL
G
12V 5W
+
30W 5.9
R
L WR
BAT
R
HO
L WR
PULSE GEN.
A.C.G
BR
_
REG.RECTI
BATTERY
WINKER RELAY
DIMMER S/W.
WINKER S/W.
HORN S/W.
12V MF6AH
ST-MAG S/W
HAZARD S/W
ST-MOTOR
LIGHTING
BAT
TL
DIMMER
HL
RE
P
(N)
60
HL
BR Br/W
P
WR
L
R
WR
HO
L
BAT
ST
E
SIDE STAND S/W
IG
BAT. TR/L
COMBINATION
E
IG
E
BAT HO
WHITE
Gr
GRAY
LO
R
FREE
FREE
FREE
FREE
FREE
LOCK
B
BLACK
Br
BROWN
N
PUSH
PUSH
PUSH
PUSH
PUSH
OFF
Y
YELLOW
O
ORANGE
CORD
COLOR
L
HI
B
R
LO
TRUNK LAMP
START
HORN
(N)
CORD
COLOR
M
CORD
COLOR
HI
HAZARD
TURN
L
Br/W
W
CORD
COLOR
SB
GR
O
SB
GR
O
CORD
COLOR
LG
B
CORD
Y/R
COLOR
B
CORD
R
COLOR
B
CORD
B/W
COLOR
G
ON
CORD
B/W
COLOR
W
L
G
R
B
BLUE
SB
G
GREEN
LG
LIGHT GREEN
R
RED
P
PINK
SKY BLUE
*NS125DLX(48~64)02.11.53:48PM페이지61
MEMO
61
*NS125DLX(48~64)02.11.53:48PM페이지62
MEMO
62
*NS125DLX(48~64)02.11.53:48PM페이지63
MEMO
63
*NS125DLX(48~64)02.11.53:48PM페이지64
MEMO
64
*NS-125DLXO/M02.11.53:42PM페이지48
OWNER’S MANUAL
2002. 1. PRINTED
2001. 1. PUBLICATION
NO COPY