Mitsubishi ws-48413 Service manual

Service
Manual
2003
MITSUBISHI ELECTRIC
PROJECTION TELEVISION
V22 / V22+ CHASSIS
V22 Chassis
MODELS
V22+ Chassis
MODELS
WS-48313
WS-55313
WS-65313
WS-48413
WS-55413
WS-65413
WS-48313
CAUTION:
Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and
"PRODUCT SAFETY NOTICE" contained in this manual.
SPECIFICATIONS
• Input Level
• Power
: AC 120V, 60Hz
240W
• Frequency
Range
: VHF 54 ~ 470MHz
UHF 470 ~ 806MHz
• Antenna Input
: VHF/UHF 75Ω unbalanced
• CRT Size
: 7 inches
• High Voltage
: 30.8KV
• Speakers
: [WS-48313 / WS-48413]
Two 5" round, full range (8Ω 10W)
: [WS-55313 / WS-55413 / WS-65313/
WS-65413]
Two 6" round, full range (8Ω 10W)
• Digital Inputs
• Output Level
• Weight / Cabinet Demensions
Model
WS-48313
WS-48413
WS-55313
WS-55413
WS-65313
WS-65413
Weight
172 lbs
172lbs
213 lbs
221 lbs
327 lbs
327 lbs
Height
49"
49"
50.4"
50.4"
62"
62"
Width
44.5"
44.5"
50.5"
50.5"
59"
59"
Depth
24"
24"
25.4"
27.8"
28"
28"
: VIDEO IN JACK (RCA Type)
1.0Vp-p 75Ω unbalanced
: AUDIO IN JACK (RCA Type)
-4.7dBm 43kΩ unbalanced
: S-VIDEO IN JACK (Y/C separate)
Y=1.0 Vp-p C=0.286Vp-p(BURST)
75Ω unbalanced
: COMP / Y, Cr, Cb (RCA Type)
Y=1.0 Vp-p. Cr, Cb=700mVp-p
: DTV / Y(G), Pr(R), Pb(B), H, V
Y 1.0Vp-p with sync 75Ω (RCA Type)
Pr, Pb: 700mV 75Ω
H, V: 3.0Vp-p 75Ω
:MonitorLinkTM/DVI
:MonitorLinkTM Control/RS-232C
: VIDEO OUT JACK (RCA Type)
1.0Vp-p 75Ω unbalanced
: AUDIO OUT JACK (RCA Type)
-4.7dBm 4.7kΩ unbalanced
• Weight and dimensions shown are approximate.
• Design specifications are subject to change without notice.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road, Irvine, CA 92618-1904
Copyright © 2003 Mitsubishi Digital Electronics America, Inc.
All Rights Reserved
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CONTENTS
INTRODUCTION ............................................................................................................................... 5
PRODUCT SAFETY NOTICE ........................................................................................................... 5
SAFETY PRECAUTIONS ................................................................................................................. 6
DISASSEMBLY PROCEDURES ......................................................................................................... 7
WS-48313 / WS-48413
Front Cabinet Components .................................................................................................... 7
Rear Cabinet Components ..................................................................................................... 8
WS-55313 / WS-55413 / WS-65313 / WS-65413
Front Cabinet Components .................................................................................................... 9
Rear Cabinet Components ................................................................................................... 10
SERVICING THE LENTICULAR LENS AND FRESNEL SCREEN ................................................ 11
WS-48313 / WS-48413
Removal of the Lenticular Screen and Fresnel Lens .......................................................... 11
WS-55313 / WS-55413 / WS-65313 / WS-65413
Removal of the Lenticular Screen and Fresnel Lens .......................................................... 12
All Models
Installation of the Lenticular Screen and Fresnel Lens ....................................................... 13
CABINET SEPARATION PROCEDURES .......................................................................................... 14
WS-65313 / WS-65413 ................................................................................................................. 14
SERVICING THE DIAMONDSHIELDSTM r ........................................................................................ 15
DiamondShields TM Removal ......................................................................................................... 15
DiamondShields TM Installation ...................................................................................................... 15
SERVICING PCBs ............................................................................................................................ 16
Chassis Removal .......................................................................................................................... 16
PCB Locations .............................................................................................................................. 16
Major Parts Locations ................................................................................................................... 16
ANODE LEAD REMOVAL ................................................................................................................. 17
CRT REPLACEMENT ....................................................................................................................... 17
CRT Removal ................................................................................................................................ 17
CRT Installation ............................................................................................................................ 18
ELECTRICAL ADJUSTMENTS ...................................................................................................... 20
Equipment .................................................................................................................................... 20
Initial Setup ................................................................................................................................... 21
LED Indicator Diagnostics ............................................................................................................. 22
Circuit Adjustment Mode ............................................................................................................... 23
Convergence Adjustment Mode ..................................................................................................... 24
Adjustment Items List ................................................................................................................... 26
Adjustment Procedures ................................................................................................................ 29
Test Point Locations ............................................................................................................ 29
HV Regulation ...................................................................................................................... 30
Main / Sub Y Level ............................................................................................................... 30
Main / Sub Color Level ......................................................................................................... 31
CRT Cutoff ........................................................................................................................... 31
White Balance (NTSC) ......................................................................................................... 32
Page 3
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
White Balance (HD) ............................................................................................................. 32
Black Level .......................................................................................................................... 33
Sub Contrast ....................................................................................................................... 33
Dynamic Focus Presets ...................................................................................................... 34
Lens Focus .......................................................................................................................... 34
Alignment Magnet & Electrostatic Focus ............................................................................. 35
Charactrer Position .............................................................................................................. 35
Geometry Presets ............................................................................................................... 36
Deflection Geometry Adjustments ........................................................................................ 37
Convergence Geometry Adjustments ................................................................................... 38
Centering & Static Convergence ........................................................................................... 39
Coarse Convergence Adjustments ........................................................................................ 40
Fine Convergence Adjustments ............................................................................................ 41
CHIP PARTS REPLACEMENT ......................................................................................................... 42
REPLACEMENT PARTS .................................................................................................................. 43
Parts Ordering .............................................................................................................................. 43
Critical and Warranty Parts Designation ........................................................................................ 43
Parts Tolerance Codes .................................................................................................................. 43
Quick Reference List .................................................................................................................... 44
SERVICE PARTS LIST .................................................................................................................... 45
SCREEN ASSEMBLY PARTS LIST .................................................................................................. 57
CIRCUITRY BLOCK DIAGRAMS ..................................................................................................... 60
CONTENTS
Part 2
Schematic Diagrams
Page
SCHEMATIC DIAGRAMS
PCB Interconnect Diagram .............................................................................................................. 1
PCB-MAIN ...................................................................................................................................... 2
PCB-POWER ................................................................................................................................. 3
PCB-SIGNAL-1 (TUNER I/O) ........................................................................................................... 4
PCB-SIGNAL-2 (MICRO) ................................................................................................................. 5
PCB-SIGNAL-3 (VIDEO / CHROMA) ............................................................................................... 6
PCB-SIGNAL-4 (CONVERGENCE GENERATOR) .......................................................................... 7
PCB-DOUBLER-1 ........................................................................................................................... 8
PCB-DOUBLER-2 ........................................................................................................................... 9
PCB-DOUBLER-3 ......................................................................................................................... 10
PCB-TERMINAL-1 (A/V I/O) .......................................................................................................... 11
PCB-TERMINAL-2 (MonLink) ........................................................................................................ 12
PCBsCRT, CONTROL, FRONT and PREAMP .............................................................................. 13
PCB LAYOUT DIAGRAMS ............................................................................................................... 14
Page 4
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
INTRODUCTION
This service manual provides service instructions for the PTV Models listed below. Service personnel should read this
manual thoroughly before servicing these chassis.
V22 Chassis
WS-48313
WS-55313
WS-65313
V22+ Chassis
WS-48413
WS-55413
WS-65413
This service manual includes:
1. Assembly and disassembly instructions for the front and rear cabinet components.
2. Servicing of the Lenticular Screen and Fresnel Lens.
3. Servicing printed circuit boards (PCBs).
4. CRT replacement procedure.
5. Electrical adjustments.
6. Chip parts replacement procedures.
7. Circuit path diagrams.
The parts list section of this service manual includes:
1. Cabinet and screen parts.
2. Electrical parts.
Schematic and block diagrams of the above listed models are included in this service manual for better understanding of the circuitry. PCB drawings are also included for easy location of parts and test points.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety related characteristics. These
characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be
obtained by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have special safety characteristics are identified in this service manual.
Electrical components having such features are identified by shading
on the schematic diagram and by bold
type in the parts list of this service manual. The replacement for any safety part should be identical in value
and characteristics.
Page 5
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SAFETY PRECAUTIONS
NOTICE:
WARNING:
1.
2.
3.
Observe all cautions and safety related notes located inside the receiver cabinet and on the
receiver chassis.
Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard
from the receiver's power supplies. Work on the receiver should not be attempted by anyone who is
not thoroughly familiar with the precautions necessary when working on high voltage equipment.
Do not install, remove or handle the picture tubes in any manner unless shatterproof goggles are
worn. People not so equipped should be kept away while the picture tube is being handled. Keep
the picture tube away from the body while handling.
When service is required, observe the original lead dress. Extra precaution should be taken to
assure correct lead dress in the high voltage area. Where a short-circuit has occurred, replace those
components that indicate evidence of overheating.
X-Radiation warning
The surface of the cathode ray tubes (CRTs) may generate X-Radiation, so take proper precautions when servicing. It is recommended that a lead apron be used for shielding while handling the CRT. Use this method if
possible.
When replacing the CRTs, use only the designated replacement part since it is a critical component with regard to
X-Radiation. High voltage must be set as prescribed under the section titled Electrical Adjustments.
Leakage current check
Before returning the receiver to the customer, it is recommended that leakage current be measured according to
the following methods.
1. Cold Check
With the alternating current (AC) plug removed from the AC source, place a jumper across the two AC plug
prongs. Connect one lead of an ohm meter to the AC plug and touch the other lead to each exposed metal
part (i.e. antennas, handle bracket, metal cabinet, screw heads, metal overlay, control shafts, etc.), particularly any exposed metal part that has a return path to the chassis. The resistance of the exposed metal parts
having a return path to the chassis should be a minimum of 1Mega Ohm. Any resistance below this value
indicates an abnormal condition and requires corrective action.
2. Hot Check ...Use the circuit shown below to perform the hot check test.
1. Keep switch S1 open and connect the receiver to the measuring circuit. Immediately after
connection, and with the switching devices of the receiver in their operating positions, measure
the leakage current for both positions of switch S2.
2. Close switch S1, energizing the receiver. Immediately after closing switch S1, and with the
switching devices of the receiver in their operating positions, measure the leakage current for both
positions of switch S2. Repeat the current measurements of items 1 and 2 after the receiver has
reached thermal stabilization. The leakage current must not exceed 0.5 milliampere (mA).
Page 6
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CABINET DISASSEMBLY (FRONT VIEW)
WS-48313
WS-48413
*Refer to PARTS LIST for Part Numbers
Front Cabinet Disassembly
1. Remove the Speaker Grille by pulling forward.
2. Remove the Board-Front by removing six screws "a".
3. Remove the Screen Assembly by removing four screws "b". Disconnect all cable harnesses between the
Screen Assembly and the PCB-Signal.
4. Lift the Screen Assembly and pull up and away from the cabinet as shown.
Page 7
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CABINET DISASSEMBLY (REAR VIEW)
WS-48313 / WS-48413
Rear Cabinet Disassembly
1.
2.
3.
4.
Remove the Back Board by removing 14 screws "a", “b” and “c”.
Remove the Back Cover by removing screws "e".
Remove 4 screws "d" securing the Light Box Assembly.
Be certain that all cables and connectors between the Light Box Assembly and external items are disconnected (e.g. speaker plugs).
5. Slide the Light Box Assembly out of the cabinet.
Page 8
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CABINET DISASSEMBLY (FRONT VIEW)
WS-55313
WS-65313
WS-55413
WS-65413
Front Cabinet Disassembly
1. Remove the Speaker Grille by pulling forward.
2. Remove the Front-Board by removing screws "a".
3. Remove the Screen Assembly by removing 5 screws "b". Disconnect connectors CC and ZF between the
Screen Assembly and the PCB-Signal.
4. Lift the Screen Assembly and pull up and away from the cabinet as shown.
Page 9
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CABINET DISASSEMBLY (REAR VIEW)
WS-55313
WS-65313
Rear Cabinet Disassembly
1.
2.
3.
4.
5.
WS-55413
WS-65413
Remove the Back Board by removing 13 screws "a" (15 screws “a” in 65 inch models).
Remove the Board Slide by removing four screws “b”.
Remove the two Board Shelves by removing 8 screws “c”.
Remove 4 screws "d" securing the Light Box Assembly.
Be certain that all cables and connectors between the Light Box Assembly and external items are disconnected (connectors CC, ZF and EJ)).
6. Slide the Light Box Assembly out of the cabinet.
Page 10
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
WS-48313
CAUTION:
WS-48413
Wear gloves when handling the Lenticular Screen and Fresnel Lens.
This prevents cuts and finger prints. Do not place Fresnel Lens in the sun.
This may cause fire and heat related injuries.
1a. Lenticular Screen and Fresnel Lens Removal
1. Remove the screen assembly as shown in the Cabinet Disassembly procedure.
2. Remove the Top, Bottom and Side Holder Screens..
3. Carefully lift the Lenticular Screen and Fresnel Lens combination from the Screen Frame Assembly.
Note: When separating the Lenticular Screen from the Fresnel Lens, use caution
while prying the Screen and Lens apart. Use a slot type screw driver, and
remove the pressure sensitive double sided tape.
Page 11
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
WS-55313
WS-65313
CAUTION:
WS-55413
WS-65413
Wear gloves when handling the Lenticular Screen and Fresnel Lens.
This prevents cuts and finger prints. Do not place Fresnel Lens in the sun.
This may cause fire and heat related injuries.
1b. Lenticular Screen and Fresnel Lens Removal
1. Remove the screen assembly as shown in the Cabinet Disassembly procedure.
2. Remove the HOLDER-SCREEN-BOTTOM.
3. Carefully slide the Lenticular Screen and Fresnel Lens combination from the upper Screen Frame Assembly.
Note: When separating the Lenticular Screen from the Fresnel Lens, use caution
while prying the Screen and Lens apart. Use a slot type screw driver, and
remove the pressure sensitive double sided tape.
1b. Installing the Fresnel Lens and Lenticular Screen
1. Insert the Lenticular Screen and Fresnel Lens combination into the upper Screen Frame.
2. Install the HOLDER-SCREEN-BOTTOM, install the end screws first. .
Page 12
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
2. Installation of the Lenticular Screen and Fresnel Lens
Note: Store the Lenticular Screen and Fresnel Lens in a cool dry place. High humidity may
deform the Lenticular Screen and Fresnel Lens.
1. Apply double coated tape (Part # LENS-TAPE) along the top front edge of the Fresnel Lens
as shown in Figure 2-2. Refer to Table B for proper tape length.
2. Place the Fresnel Lens on top of the Lenticular Screen and apply pressure at the top edge to
bond them together as shown in Figure 2-2.
3. Reverse the disassembly procedure for that model to install the screens in the screen frame.
Fresnel Lens
Top
Fresnel
Lens
Lenticular
Screen
( * X ) inch
Top
Double Sided Tape
(Part# LENS-TAPE)
Bottom
Bottom
Lenticular Screen
Figure 2-2
Model
WS-48313
WS-48413
WS-55313
WS-55413
WS-65313
WS-65413
Screen
Size
48"
48"
55"
55"
65"
65"
Table A
Page 13
Tape
Length
41.76
41.76
47.85
47.85
56.55
56.55
0.16 inch
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CABINET SEPARATION PROCEDURE
(WS-65313 / WS-65413)
Models WS-65313, and WS-65413 cabinets are assembled in two pieces. These two pieces may be separated to
allow easier delivery and setup.
Cabinet Separation Precedure
(Figure 1)
1. Pull the Speaker Grille off.
2. Unplug connectors “CC” and ZF.
3. Remove 4 screws “a” on both sides of the
cabinet.
(Figure 2)
4. Carefully lift the cabinet top until the support
tabs clear the bottom cabinet.
(Figure 3)
5. Carefully rotate the cabinet top and place it on
the floor.
6. Reverse the procedure and mount the cabinet
top on the cabinet bottom.
Figure 1
Figure 3
Figure 2
Page 14
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SERVICING THE DIAMONDSHIELD™
1. DiamondShield™ Removal Procedure
The location of the DiamondShieldTM molding clips may vary between models, top and bottom, or sides. Use
the appropriate disassembly procedure given below.
Note: Wear gloves when handling the DiamondShield™ to prevent finger prints.
Side Molding Clips
Top & Bottom Molding Clips
1. Gently insert a small screwdriver between the
DiamondShield™ and one end of the clip to pry
the clip loose.
2. Remove both clips by pulling them toward you.
3. Carefully insert a small screwdriver into the gap
at the top/center point of the Shield and pull the
Shield slightly away from the unit. Place your
hands at the points shown and gently bow the
Shield toward you and remove from the unit.
Then re-install the two clips.
1. Gently insert a small screwdriver between the
DiamondShield™ and one end of the clip to pry
the clip loose.
2. Remove both clips by pulling them toward you.
3. Carefully insert a small screwdriver into the gap
at the side/center point of the Shield and pull the
Shield slightly away from the unit. Place your
hands at the points shown and gently bow the
Shield toward you and remove from the unit.
Then re-install the two clips.
2. DiamondShield™ Installation Procedure
*(See the Parts List for DiamondShield™ part numbers)
To install the DiamondShieldTM, reverse the above Removal Procedure.
Page 15
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SERVICING PCBs
Chassis Removal and PCB Locations
Chassis Removal
1) Remove screw “a” from the Main Chassis.
2) Raise the two chassis locks on the inner sides of the
Lightbox Assembly and slide the chassis towards the
rear.
Major Parts Locations
Page 16
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
ANODE LEAD REMOVAL
CAUTION:
To prevent damage, the following procedure must be used when removing an
Anode Lead from the Flyback Transformer.
1) Push the Anode Lead down.
2) While holding the lead down rotate
the lead 90º counter clockwise.
3) Carefully remove the Anode Lead
from the Flyback Transformer.
CRT REPLACEMENT
1. Removal of the CRT
Caution!
High voltage should be completely discharged prior to CRT removal.
Since the CRTs receive high voltage from the Flyback transformer, discharge
by shorting the open end of the respective high voltage cable to chassis ground.
Note: Refer to Cabinet Disassembly when performing steps 1 through 2.
Remove the Speaker Grille, Front Board, and Screen Assy.
Remove the Back Board.
Remove the Anode Lead Wire from the Flyback transformer. (Use the above procedure)
Remove the PCB-CRT.
Remove 4 hex-screws "a" retaining the Optical Unit. [Figure 5-1]
Remove 4 screws "b" retaining the Lens.
Note: DO NOT loosen the RED screws. Doing so will break the seal between the
C-Element and the # 6 Lens, causing leakage of the CRT Coolant.
7. Remove 4 screws "c" retaining the CRT. [Figure 5-2]
8. Remove the Deflection Yoke and other CRT components from the neck of the CRT. [Figure 5-6]
1.
2.
3.
4.
5.
6.
Figure 5-1
Page 17
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
Note: The 4 spring-loaded screws shown
in Fig 5-2 and labeled as "DO NOT
REMOVE", should not be loosened
under any circumstance. Doing so
will break the seal between the
CRT and the CRT-Spacer, causing
leakage of the CRT Coolant.
Figure 5-2
2. Installation of the CRT
Note: The replacement CRT is supplied as an assembly comprised of the CRT and the
Inner Lens with the space between them filled with ethylene glycol. Care should
be taken during handling and installation to prevent shock from disrupting the seal
or alignment between the CRT and Inner Lens. [Figure 5-3]
Figure 5-3
Figure 5-5
Figure 5-4
Page 18
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
1. Carefully position the replacement CRT and fasten in place using 4 screws "d". [Figure 5-5]
2. Install the Deflection Yoke and other CRT components back in there original position on the CRT neck.
[Figure 5-6]
3. Install the Lens that was removed in step6 of Removal Of The CRT. [ Figures 5-1 and 5-2 ]
a) Position the Lens so that the Label faces the direction shown in Figure 5-7
b) Install the mounting screws “b”. [Figure 5-1]
4. Insert the Optical Unit into the Light Box Assembly.
5. Install the PCB-CRT.
6. Insert the Anode Lead Wire into the Flyback Transformer.
7. Re-clamp the Lead Wire in its original position.
Figure 5-6
Figure 5-7
Adjustment procedures after replacing the CRT(s)
• CRT Cut Off / White Balance Adjustment
• Static Convergence Adjustment
• Dynamic Convergence Adjustment
Page 19
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
ELECTRICAL ADJUSTMENTS
Note: Perform only the adjustments required.
Do not attempt an alignment if proper equipment is not available.
1. Test Equipment
•
•
•
•
•
•
Oscilloscope (Unless otherwise specified, use 10:1 probes)
Signal Generator (both SD and HD capable)
Frequency Counter
Direct Current Voltmeter
Direct Current Power Supply
Multiplex Audio Signal Generator
Direct Current Ampere Meter
2. Test Signal
A. Monoscope Signal
Note: If you do not have
a monoscope signal source,
connect the unit to a VCR
and play a Monoscope
*alignment tape.
(* Part Number: 859C568060)
B. Color Bar Signal
Use the color bar signal shown
below, unless otherwise specified
in this manual.
Monoscope Signal
100%
75%
40%
40%
1H
Split-Field Color Bars (100% window)
Page 20
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
3. Initial Setup
A. Option Menu Setup
Follow the steps below for the initial set-up:
1. Select the "MENU" display by pressing the "MENU" button once.
2. Press the number buttons "0", "3", "7", "0" in sequence to select the "OPTION MENU" display.
3. Press the "ADJUST" button to select "INITIAL."
4. Press "ENTER."
NOTE: At this time channel 3 is automatically selected.
MENU-0-3-7-0
OPTION MENU
Initial
Power Restore
DTV Port
Direct Key Mod
:OFF
:Auto
:OFF
B. Default Settings
MAIN MENU DEFAULT SETTINGS
SETUP Menu
Memorize Channels
Ant-A Air
Input Assignment (V22)
NetCommand® IR Setup (V22+)
Clock
Language
English
Energy Mode
Low
INPUT ASSIGNMENT Menu (V22)
Antenna-A
On
Antenna-B
On
DTV
YPrPb
Component-1
Comp-1
Component-2
Comp-2
Input-1
Input-1
Input-2
Input-2
Input-3
Input-3
MonLink
MonLink
Welcome to NetCommand® IR (V22+)
Language
English
NetCommand® IR Setup
CLOCK Menu
Clock Setting
Manual
Clock Time
--:-Set Day
Sunday
Time Zone
N/A
Daylight Savings Time
N/A
CAPTIONS Menu
Closed Captions
In Mute
CC Background
Gray
CHANNEL EDIT Menu
Antenna
ANT-A
Channel
003
Memory
Deleted
Name
N/A
SQV
N/A
V-CHIP LOCK Menu
Lock by Time
Off
Lock Time
N/A
Unlock Time
N/A
Front Button Lock
Off
V-Chip
V-CHIP Menu
V-Chip
Off
TV Rating
TV-PG
FV-Fantasy Violence
Allow
D-Sexual Dialog
Allow
L-Adult Language
Allow
S-Sexual Situation
Allow
V-Violence
Allow
Movie Rating
PG
Programs Not Rated
Allow
V-CHIP Hours
V-Chip Start Time
12:00am
V-Chip Stop Time
12:00am
ADVANCED FEATURES Menu
Color Balance
Timer
Convergence
Video Mute
On
Black Enhancement
On
COLOR BALANCE Menu
Ant-A Auto Color Correction
Off
PerfectColor™
Reset Color for Ant-A
TIMER Menu
Timer
Off
Set Time
12:00 am
Set Day
Everyday
Input
Ant-A
Channel
003
Page 21
PerfectColor™
Magenta
50%
Red
50%
Yellow
50%
Green
50%
Cyan
50%
Blue
50%
AUDIO/VIDEO SETTINGS Menu
A/V Memory Reset
Ant A
TV Speakers (Internal)
On
Audio Output
Variable
AUDIO SETTINGS
TV Bass
50%
TV Treble
50%
TV Balance
50%
TV Surround
Off
TV Listen To
Stereo
TV Level Sound
Off
VIDEO SETTINGS
TV Contrast
100%
TV Brightness
50%
TV Sharpness
50%
TV Color
50%
TV Tint
50%
TV Color Temp
High
TV Video Noise
Standard
TV Film Mode (Auto)
On
TV VSM (V22+ Only)
On
TV Volume
30%
PIP Source
Ant A Ch 3
PIP Position
Lower Right
POP Position
Right Half
Stretch
Format
PIP/POP Format
Dble Win
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
Items in the table below are set to following after Initalization.
AV Memory Initial Settings
A/V Memory
TV Contrast
TV Brightness
TV Sharpness
TV Color
TV Tint
TV Color Temp.
Video Noise
TV Image Type
TV SVM
Sharpness
TV Bass
TV Treble
TV Balance
TV Surrond
TV Listen To
TV Level Sound
Ant-A
Ant-B
Max
Center
Center
Center
Center
High
Standard
Video
Max
Center
Center
Center
Center
High
Standard
Video
NTSC
1/2/3
Max
Center
Center
Center
Center
High
Standard
Video
On
On
On
On
On
Center
Center
Center
Off
Stereo
Off
Center
Center
Center
Off
Stereo
Off
Center
Center
Center
Off
Stereo
Off
Center
Center
Center
Off
Stereo
Off
Center
Center
Center
Off
Stereo
Off
DTV
COMP
MonLink
1/2
Max
Max
Center
Center
Center
Center
Center
Center
Center
Center
High
High
Standard Standard
Video
Video
4. LED Indicator Diagnostics
The “Power ON LED” provides an indication of the sets operation, and the possible cause of a malfunction.
A. Initial Control Circuitry Check
Immediately after the TV is connected to an AC power source:
• The LED flashes three times ... indicating the Microprocessor has initialized and is functioning
properly.
• If the LED does not flash ... the Microprocessor is NOT functioning.
B. Error Code Operational Check
Note: The TV must be in “Shut Down” and not heve been switched Off, to perform the Error Code Operational Check. When the TV is switched Off, the code automatically resets to “12” No Error.
Pressing the front panel “INPUT” and “MENU” buttons at the same time, and holding for 5 seconds,
activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem
has occured since the last Initalization.
Note: The front panel buttons must be used, NOT those on the Remote Control.
• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.
• The flashing then pauses for approximately 1/2 second.
• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.
• The Error Code is repeated a total of 5 times.
Example: If the Error Code is “23”, the LED will flash two times, pause, and then flashes three
times.
C. Error Codes
The Error Code designations indicating a malfunction, or no malfunction, are listed below:
Error Cod e
12
21
22
23
De scrip tio n
No error has oc c urred.
X-Ray P rotec t c irc uit.
S hort P rotec t c irc uit.
Deflec tion failure.
Page 22
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
5. Circuit Adjustment Mode
Except for the following, all adjustment items must be performed
using the remote hand unit.
• CRT Cutoff
• Lens Focus
• Electrostatic Focus
A. Activating the Circuit Adjustment Mode
FUNCTION
CHASSIS
Video Chr
1. Press the "MENU" button on a remote hand unit.
MODE
Mode 0
2. Press the number buttons "0", 3", "5", "7" in sequence.
The screen will change to the Adjustment Mode.
ITEM#
1
V22
NTSC
SCT
ABBREV.
Note: Repeat steps 1 and 2 if the circuit
adjustment mode display does not appear
on screen
SIGNAL
55
DATA
B. Selection of adjustment Functions and
Adjustment Items
To select an adjustment item in the circuit adjustment mode,
first select the adjustment function that includes the specific
adjustment item to be selected. Then, select the adjustment
item.
CABLE/DBS
VCR
DVD
AUDIO
TV
Refer to the following pages for the listing of adjustment
functions and adjustment items.
1
1. Press the "AUDIO" button on a remote hand unit to
select an adjustment function. Each time the button
is pressed, the Function changes in the following
sequence:
2
3
6
4
5
7
8
9
SQV
0
QV
POWER
SLEEP
VIDEO
INPUT
CHANNEL VOLUME
AUDIO
VIDEO
AUDIO
MUTE
Video Chr
Defl Jung
ENTER
ENTER
GUIDE
CANCEL
MENU
FUNCTIONS
HOME
PIP/POP
PIP SIZE
HR
Sub Matr
PIP INPUT PIP CH
EXCH
INFO
Main Matr
REC
2. Press the “VIDEO” button to select a specific
Adjustment Item. The Item number increases each
time the “VIDEO” button is pressed.
C. Changing Data
After selecting an adjustment Item, use the “ADJUST
UP/DOWN” button to change data.
•
Press “ADJUST DOWN” to decrease the data value.
•
Press “ADJUST UP” to increase the data value.
Page 23
REW/REV
STOP
PLAY
PAUSE
FF/FWD
ADJUST
UP/DN
MENU
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
D. Saving Adjustment Data
Press “ENTER” to save adjustment data in memory. The character display turns red for
approximately one second in this step.
Note: If the circuit adjustment mode is terminated without pressing “ENTER”, changes
in adjustment data are not saved.
E. Terminating the Circuit Adjustment Mode
Press the “MENU” button on the remote hand unit twice to terminate the adjustment mode.
Note: The circuit adjustment mode can also be terminated by turning power OFF.
F. Service Mode Reset
To reset items in the service mode to their factory values:
1.
Press MENU-0-3-5-7 to enter the Service Mode.
2.
Press the “INPUT” or “DEVICE” button, on the front panel or the remote, and hold for 2 seconds.
6. Convergence Adjustment Mode
The Convergence mode is used to perform raster geometry correction, and convergence adjustments as
specified in Adjustment Procedures 15 through 18.
A. Convergence Mode Activation
1.
2.
Press MENU-0-3-5-9
When the Convergence Mode is activated, the display at
the right appears on a Green Crosshatch.
B. Selecting the HD or SD Mode
1.
2.
3.
4.
SD
Coarse GREEN
1
HSTA
-50
Coarse Conv. Display
Select the Signal Source before entering the Convergence Mode, either an NTSC or HD source.
Enter the Convergence Mode (MENU-0-3-5-9)
• If the signal source is NTSC, the SD mode is activated.
• If the signal source is HD 1080i, the HD mode is activated.
Activating the HD mode when no HD signal is available.
• Activate the Factory Option Menu (MENU-0-3-7-0)
• Use the “Adjust” keys to select “DTV Port” and press “Enter” to change the setting to “1080i”.
Sequence = “Auto”-”480i”-”480p”-”1080i”. Ignore any loss of sync while changing modes.
• Exit the Option Menu (Press “MENU” twice).
• Select the DTV Inputs as the signal source (INPUT or DEVICE button).
• Activate the Convergence Mode ... the Convergence mode will be in the HD mode and the internal
crosshatch is displayed.
After adjusting Convergence, be sure to set the DTV Port back to AUTO.
• Select an analog input as the signal source (INPUT or DEVICE button).
• Activate the Option Menu (MENU-0-3-7-0).
• Use the “Adjust” keys to select “DTV Port and press “Enter” to change the setting from “1080i” to
“AUTO”.
• Exit the Option Menu (Press MENU twice).
C. Convergence Mode Functions
In the Convergence Mode there are three main Functions (Categories).
• Pressing “6” activates CONV MISC
• Pressing “5” activates COARSE CONV
• Pressing “4” activates FINE CONV
Page 24
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
D. CONV MISC (Press 6)
This mode is used to preset data values controlling the Convergence Generator, and to perform the HV
Regulation adjustment.
1.
Use the VIDEO button to select an item.
2.
Use the ADJUST buttons to change data.
Note: When Item “1 HVOL” is selected the screen goes black except for the data display.
This occurs since a black screen is required when making the HV Regulation adjustment.
E. COARSE CONV (Press 5)
There are four Sub Functions in the Coarse mode, COARSE GREEN, RED and BLUE, and DF.
• COARSE GREEN .... used to make Coarse Raster Geometry Adjustments.
• COARSE RED ... used to make Coarse Red Convergence Adjustments.
• COARSE BLUE ... used to make Coarse Blue Convergence Adjustments.
• DF ... used to preset data values controlling the Dynamic Beam Focus circuit drive signal.
1.
Use AUDIO button to select a Sub Function
2.
Use the VIDEO button to select an Adjustment Item.
3.
Use the ADJUST buttons to change data.
F. FINE CONV (Press 4)
Sub Functions
This mode is used to perform Fine Raster Correction, and Fine Red and Blue Convergence Adjustments.
There are three Sub Adjustment Functions, selected with the AUDIO button:
• FINE GREEN .... a Green Crosshatch is displayed, for Fine Raster Corrections.
• FINE RED .... a White Crosshatch is displayed, for Fine Red Convergence Adjustments.
• FINE BLUE .... a White Crosshatch is displayed, for Fine Blue Convergence Adjustments.
Cursor
In the Fine mode a Cursor is added to the Crosshatch. The ENTER button toggles the Cursor between two
modes:
• MOVE (blinking Cursor) .... use the ADJUST buttons to select any of 64 points on the Crosshatch.
• ADJUST (Non blinking Cursor) .... the ADJUST buttons adjust the active color at the current Cursor
position, horizontally or vertically.
Page 25
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
Cursor Coordinates
Specific intersections in the Crosshatch are assigned vertical and horizontal coordinates.
These are shown in the preceeding diagram. The Cursor can only be moved to those positions that
have coordinates assigned. If the Cursor is at coordinates outside the screen area, the Cursor will not be
visible. Use the ADJUST buttons to move the Cursor to an intersection on the screen.
Display
The on-screen display changes in the Fine mode, as shown below.
The display shows the vertical and horizontal data for the current
Cursor Position, and the horizontal and vertical coordinates for
that position.
Horiz.
Data
SD
Fine RED
13
H1 V3
-32
H Coord. V Coord.
F. Saving Data and Exiting the Convergence Mode
Vert.
Data
Press MENU twice to exit the Convergence mode, data is automatically saved.
Note: If power is interrupted, or the “CANCEL” button is presssed prior to properly exiting the Convergence
Mode, changes in adjustment data will not be saved. The data is restored to the last saved previous
values.
ADJUSTMENT ITEMS LIST
Video Chroma Function
Data
Item# Abbrev.
Description
Range 480i 480p 1080i Adjustment
1
SCT
Picture Gain control
0~63
42
42
42
Sub Contrast
2
SBRT
Sub Brightness
0~63
20
20
20
Black Level
3
SCON
Sub Contrast
0~15
7
7
7
Preset
4
RDRH
R Drive (H temp)
0~63
31
31
31 White Balance
5
GDRH
G Drive (H temp)
0~63
41
41
41
Preset
6
BDRH
B Drive (H temp)
0~63
31
31
31 White Balance
7
CTRH
R Cutoff (H temp)
0~63
31
31
31
"
8
CTGH
G Cutoff (H temp)
0~63
31
31
31
Preset
9
CTBH
B Cutoff (H temp)
0~63
31
31
31 White Balance
10
RDRL
R Drive (L temp)
0~63
31
31
31
"
11
GDRL
G Drive (L temp)
0~63
41
41
41
Preset
12
BDRL
B Drive (L temp)
0~63
31
31
31 White Balance
13
CTRL
R Cutoff (L temp)
0~63
31
31
31
"
14
CTGL
G Cutoff (L temp)
0~63
31
31
31
Preset
15
CTBL
B Cutoff (L temp)
0~63
31
31
31 White Balance
16
GMMA
RGB Gamma Correction
0~3
2
2
2
Preset
17
GAML
Gamma Differential Corr. Switch
0~1
0
0
0
"
18
BRT
Brightness
0~63
31
31
31
"
19
COL
Color
0~63
38
34
33 White Balance
20
TINT
Tint
0~63 29** 30
29
Preset
21
SHRP
Sharpness
0~63
31
31
31
"
22
CBOF
Cb DC Offset
0~63
31
31
31
"
23
CROF
Cr DC Offset
0~63
31
31
31
"
31
VMLE
VM Output Level
0~3
1
1
2
"
40
AGIW
White output aging mode switch
0~1
0
0
0
"
55
ABLT
Threshold Adjust for ABL input
0~15
4*
4*
4*
"
* For models WS-55413, WS-65313 & WS-65413 set data to 0
**For models WS-48313 and WS-48413 set #20 TINT data to 29
For models WS-55313 and WS-55413 set #20 TINT to 28
For models WS-65313 and WS-65413 set #20 TINT data to 30
Page 26
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
Deflection Jungle
Item
1
2
7
8
9
18
36
Abbrev.
HWID
HKEY
VHGT
VLIN
VSCN
VPOS
PINA
WS-48313 WS-48413 WS-55313 WS-55413 WS-65313
Description
Range NTSC HD NTSC HD NTSC HD NTSC HD NTSC HD
Width
0~63
30
29
30
29
23
22
25
25
32
32
Horiz. Keystone
0~63
24
25
24
25
24
25
24
25
24
25
Height
0~63
18
16
18
16
14
13
28
28
36
31
Vert. Linearity
0~15
5
5
5
5
5
5
5
5
7
7
Vert. S Corr.
0~15
0
0
0
0
0
0
0
0
0
0
Vert. Position
0~63
31
31
31
31
31
31
31
31
31
31
Pincushion Comp. 0~63
10
8
10
8
10
8
10
8
10
8
MAIN MATRIX
Item#
39
41
Abbrev.
SCNT
SCLR
Description
Main Y-Out
CbCr Amp
MENU-0-3-5-7
Data
Range
Initial
0~31
16
0~31
16
Description
Main Y-Out
CbCr Amp
MENU-0-3-5-7
Data
Range
Initial
0~31
16
0~31
16
SUB MATRIX
Item#
39
41
Abbrev.
SCNT
SCLR
HR
Item#
1
Abbrev.
HR
Description
NTSC Disp.Pos.
WS-65413
NTSC HD
30
28
24
25
33
31
7
7
0
0
31
31
10
8
MENU-0-3-5-7
Initial
29
CONVERGENCE MODE ITEMS
CONV MISC.
Ite m #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Abbre v.
HVOL
VCNT
VSTR
VOFS
STLN
FPHS
CPHS
HOFS
DPHS
DOFS
TPHS
TPVD
ODEV
HRTC
DRTC
DAC
EPW P
De scription
HV Adjust
V-saw amplitude
V-saw start timer
V-saw offset
Start line
Fine phase
Coarse phase
H-saw offset
DF coarse horiz phase
DF offset
Test Pattern phase
Test Pattern Vert. Position
Odd/Even detection
H-saw retrace
DF retrace
External DAC selection
EEPROM write protection
Page 27
Ra nge
0~352
0~127
0~127
0~127
0~127
0~352
0~31
0~127
0~31
0~127
0~352
0~127
0~352
0~3
0~3
0~1
0~1
MENU-0-3-5-9-6
Da ta
SD
HD
150
150
29
29
0
10
10
8
38
26
303
294
15
15
22
22
1
1
34
34
43
39
23
39
24
42
1
1
1
1
1
1
0
0
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
COARSE CONV GREEN
# Abbrev. Description
1
2
3
4
5
6
7
8
9
10
11
12
HSTA
VSTA
SKEW
TILT
HWID
HLIN
SPCC
HKEY
TBPC
VKEY
VWID
VLIN
Horiz. Position
Vert. Position
Skew (Y axis)
Tilt (X axis)
Width
Horiz. Linearity
Side PC Corr.
Horiz. Keystone
Top/Bottom PC
Vert. Keystone
Height
Vert. Linearity
COARSE CONV RED
# Abbrev. Description
1
2
3
4
5
6
7
8
9
10
11
HSTA
VSTA
SKEW
TILT
HLIN
HWID
VKEY
VWID
VLIN
TBPC
SDBW
Horiz. Position
Vert. Position
Skew (Y axis)
Tilt (X axis)
Horiz. Linearity
Width
Vert. Keystone
Height
Vert. Linearity
Top/Bottom PC
Side Bow
COARSE CONV BLUE
# Abbrev. Description
1
2
3
4
5
6
7
8
9
10
11
HSTA
VSTA
SKEW
TILT
HLIN
HWID
VKEY
VWID
VLIN
TBPC
SDBW
Horiz. Position
Vert. Position
Skew (Y axis)
Tilt (X axis)
Horiz. Linearity
Width
Vert. Keystone
Height
Vert. Linearity
Top/Bottom PC
Side Bow
WS-48313 WS-48413 WS-55313 WS-55413
SD HD SD HD SD HD SD HD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
20
20
20
20
20
20
20
20
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
23
20
23
20
15
10
20
20
-180 -160 -180 -160 -190 -165 -190 -180
0
0
0
0
0
0
-4
8
30
20
30
20
30
20
30
20
0
0
0
0
0
0
0
0
MENU 0-3-9-5
WS-65313 WS-65413
SD HD SD HD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
20
20
20
20
0
0
0
0
0
0
0
0
0
0
0
0
-200 -175 -200 -175
0
0
0
0
30
20
30
20
0
0
0
0
WS-48313
SD HD
50
50
0
0
5
5
0
0
-220 -200
0
0
-90 -90
0
0
0
0
20
20
30
30
WS-55413
SD HD
50
50
0
0
5
5
0
0
-195 -180
-10
-5
-90 -70
0
0
0
0
20
20
30
30
MENU 0-3-9-5
WS-65313 WS-65413
SD HD SD HD
50
50
50
50
0
0
0
0
0
0
0
0
0
0
0
0
-170 -150 -170 -150
10
10
10
10
-90 -75 -90 -75
0
0
0
10
0
0
0
0
20
20
20
20
30
30
30
30
WS-55313 WS-55413
SD HD SD HD
-50 -50 -50 -50
0
0
0
0
0
-5
0
0
0
0
0
0
220 205 195 180
0
0
-10 -15
90
70
90
70
0
0
0
0
0
0
0
0
0
0
-20
0
-30 -30 -30 -30
MENU 0-3-9-5
WS-65313 WS-65413
SD HD SD HD
-50 -50 -50 -50
0
0
0
0
0
0
0
0
0
0
0
0
175 160 175 160
10
10
10
10
80
75
80
75
0
0
0
0
0
0
0
0
-20
0
-20
0
-30 -30 -30 -30
WS-48313
SD HD
-50 -50
0
0
0
-5
0
0
220 200
0
0
90
90
0
0
0
0
0
0
-30 -30
WS-48413
SD HD
50
50
0
0
0
0
0
0
-220 -200
0
0
-90 -90
0
0
0
0
20
20
30
30
WS-48413
SD HD
-50 -50
0
0
0
0
0
0
220 200
0
-15
90
90
0
0
0
0
-20
0
-30 -30
WS-55313
SD HD
50
50
0
0
0
0
0
0
-215 -195
0
0
-75 -75
0
0
0
0
20
20
30
30
DF
MENU-0-3-5-9-5
Item
Abbr.
0
1
DFH
DFV
WS-48313 / WS-48413
WS-55313
SD Data HD Data
-220
-220
-100
-100
Page 28
WS-55413 / WS-65313
WS-65413
SD Data HD Data
-280
-250
-110
-95
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
Adjustment Test Point Location
Test Points
DT pin 3 - HV Adjust
DT pin 6 - Ground
DT pin 7 - 12 Volts
DT pin 8 - ACL
JA pin 22 - Main Picture (Y)
JA pin 20 - Main Color (Pr)
JB pin 3 - Sub Picture (Y)
JB pin 5 - Sub Picture (Cr)
TP6(R, G or B) - CRT Cathode
Page 29
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[HV Circuit]
Purpose:
To set the CRT Anode voltage.
1. HV Regulation
Symptom:
Dark Picture
Measuring
Instrument
DC Voltmeter
Test Point
DT connector pins 3 & 6
Ext. Trigger
------
Measuring
Range
-------
Input Signal
Video Signal
Monoscope
Input Terminal
Video Input
Note: This adjustment must be rechecked following Adjustment 9 CRT Cutoff.
1. Supply a video monoscope signal.
2. Set Contrast to maximum, and Brightness to mid position.
3. Connect a DC volt meter between pins 3 and 6 of the DT connector.
(Positive lead to pin 3)
4. Activate the Conv-Misc Mode.
5. Select Item “1 HVOL” (screen goes black).
6. Adjust Item “1 HVOL” for 15.4V ±0.02V on the meter.
7. Save data and exit the Conv-Misc mode.
8. Confirm that the voltage does not change more than 0.15V.
Note: This adjustment must be performed if E2RESET or Convergence E2RESET
are activated.
CONVERGENCE MODE
Activate ……..MENU-0-3-5-9
Misc. ……………….……"6"
Coarse………………..…."5"
Fine ……………………..."4"
Color (R,G or B)……AUDIO
Item No………….…..VIDEO
Adjust/Move……….ADJUST
Cursor Toggle….…..ENTER
Save & Exit…..MENU (twice)
[Video Circuit]
Purpose
To set picture luminance
2. Main/Sub Y Level
Symptom:
Excess or insufficient brightness.
Measuring
Instrument
Oscilloscope
Test Point
JA Connector pin 22
JB Connector pin 3
Ext. Trigger
------
Measuring
Range
Input Signal
------
Input Terminal
Video Input
Color Bars
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Supply a color bar signal to a Video Input (not an RF input).
Select the color bar signal for both the main and sub pictures.
Connect the oscilloscope to connector JA pin 22 (Main-Y).
Activate the Adjustment Mode
Select Item “39 SCNT” in the Main Matrix function.
Adjust the data so the Main-Y signal is between 0.71 Vp-p max. and 0.66 Vp-p
min. at JA pin 22.
(If it cannot be adjusted within this range, set to the lower value)
Move the oscilloscope to connector JB pin 3 (Sub-Y).
Select Item “39 SCNT” in the Sub Matrix function.
Adjust the data to equal the MAIN-Y Gain (+0.0V -0.05V).
Press “ENTER” to save data.
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
Page 30
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Video Circuit]
Purpose:
3. Main/Sub Color Level
Symptom: Main and sub pictures colors differ.
Measuring
Instrument
Oscilloscope
Test Point
JA pin 22
JB pin 5
------
Ext. Trigger
Measuring
Range
------
Input Signal
Color Bars
Input Terminal
Video
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
To match the sub picture color to that of the main picture.
Supply an NTSC signal to an External Video Input.
Select the NTSC signal as the source for both the main and sub pictures.
Connect an oscilloscope to connector JA pin 20 (Main PR).
Activate the Adjustment mode.
Select Item “41 SCLR” in the Main Matrix Function.
Adjust data so the PR signal is 0.71 Vp-p max. - 0.66 Vp-p min
(If it cannot be adjusted within this range, set to the lower value)
When using a Leader 480, set to 0.585±0.02Vp-p.
Connect an oscilloscope to connector JB pin 5 (Sub PR).
Select item “41 SCLR” in the Sub Matrix Function.
Adjust so Sub PR = Main PR (+0.0V -0.05V)
Press “ENTER” to save data.
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
[CRT Circuit]
Purpose
To set the cutoff point for all three CRTs.
4. CRT Cutoff
Symptom:
Monochrome has a color tint, or incorrect brightness.
Measuring
Instrument
Oscilloscope
Test Point
TP6R, TP6G, TP6B
Ext. Trigger
------
Measuring
Range
Input Signal
50V/Div. 2msec/Div.
Input Terminal
Video Input
None
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
Note: Use the Expand mode (full screen)
1. Select an External Input with no signal.
2. Enter the Adjustment Mode, Video Chroma Function.
3. Press “1”, automatically blanks the screen and sets COL to 0.
4. Set the data to the values given in the table below.
5. Connect the oscilloscope to TP6R.
6. Adjust the Red Screen VR so the black level is 170V, as shown below, or
178V ±1VDC using an DC Voltmeter.
7. Repeat Steps 4 and 5 to set the Blue and Green Screen VRs, using
TP6G and TP6B.
Note: White Balance must be performed after this adjustment.
VC Preset Data
Item Abbr Data
1
SCT
42
2
SBRT 20
3
SCON
7
4
RDRH 31
5
GDRH 41
6
BDRH 31
7
CTRH 31
8
CRGH 31
9
CTBH 31
Page 31
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[CRT Circuit]
Purpose:
To set the CRTs white level in the NTSC mode.
5. White Balance (NTSC)
Symptom:
Monochrome has a color tint.
Measuring
Instrument
DC Voltmeter
Note: Use the “FORMAT” button to activate the Expand mode (full screen).
Test Point
------
Ext. Trigger
------
Measuring
Range
------
Input Signal
NTSC White Raster
Input Terminal
RF or Video
1.
2.
3.
4.
5.
6.
7.
8.
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
9.
10.
11.
12.
Supply a full White Raster Signal
Activate the Service Mode, Video Chroma Function.
Set the data for Item “19 COL” to 0.
Adjust Items “4 RDRH” and “6 BDRH” for optimum white at the center of
the screen.
Reduce the input luminance level to 25%.
Adjust Items “7 CTRH” and “9 CTBH” for optimum white.
Insert a Milliammeter in series with each CRT Cathode. The maximum
allowable current for each CRT is given in the table below.
Set the white raster to 100% and adjust Items “10 RDRL” and “12 BDRL” for
optimum white at the center of the screen.
Reduce the luminance level to 25%.
Adjust Item “13 CTRL” and “15 CTBL” for optimum white.
Set the data for Item “19 COL” back to 31.
Press “ENTER” to save data.
Max CRT Current
CRT
ALL
Red
580 ua
Green
580 ua
Blue
580 ua
[CRT Circuit]
Purpose
To set the CRTs white level in the HD mode.
6. White Balance (HD)
Symptom:
Monchrome pictures have a color tint.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
Input Signal
-----
Input Terminal
DTV Inputs
HD White Raster
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Supply an HD Full White Raster signal to the DTV Inputs.
Select the DTV Inputs (Input button)
Activate the Adjustment mode, Video Chroma Function.
Set Item “19 COL” to 0.
Adjust Items “4 RDRH” and “6 BDRH” for optimum white at the center of the
screen.
Reduce the input signal luminance to 25%.
Adjust Items “7 CTRH” and “9 CTBH” for optimum white.
Set the white raster to 100% and adjust Items “10 RDRL” and “12 BDRL” for
optimum white at the center of the screen.
Reduce the luminance level to 25%.
Adjust Item “13 CTRL” and “15 CTBL” for optimum white.
Set the data for Item “19 COL” back to 31.
Press “ENTER” to save data.
Page 32
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Video Circuit]
Purpose:
To set the black level of the picture.
7. Black Level
Symptom:
Excess or insufficient brightness.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
------
Input Signal
Monoscope
Input Terminal
1. Supply a Monoscope signal to a Video Input.
2. Activate the Adjust Mode, Video Chroma Function.
3. Adjust Item “2 SBRT” so the 0% and 10% black levels on the gradation scale
are the same.
4. Press ENTER to save data.
7. Exit the Service Mode.
NOTE: Item 2 SBRT should be no more the “21”.
Video Input
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
40% 30% 20% 10%
50% 0%
0%
0%
60% 70% 80% 90%
GRADATION SCALE
[Video Circuit]
Purpose
To set overall beam current to its’ optimum level.
8. Sub Contrast
Symptom:
Excess or insufficient contrast.
Measuring
Instrument
DC ma meter
Test Point
DT connector pins 7 & 8
Ext. Trigger
------
Measuring
Range
Input Signal
-----
Input Terminal
RF Input
Note: Activate the Expand mode (full screen).
1. Supply a Grayscale signal to a RF Input.
2. Activate the Adjust Mode, Video Chroma Function.
3. Select Item “1 SCT”, signal level automatically reduces.
4. Connect a 3ma DC meter between DT connector pins 7 and 8. Positive lead to
pin 7.
5. Adjust Item “1 SCT” for the current given in the table below.
6. Remove the meter.
7. Press “ENTER” to save data.
8. Exit the Service Mode.
Grayscale
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
Sub Contrast Current Alignment
WS-48313 / WS-48413 WS-55413 / WS-65313
WS-55313
WS-65413
520 ±10ua
550 ±10ua
Page 33
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Focus Circuit]
Purpose:
9. Dynamic Focus Preset
Symptom: Poor focus at the edges of the screen.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
-----
Input Signal
Monoscope
Input Terminal
Video Input
1.
2.
3.
4.
5.
6.
7.
8.
To improve edge focus.
Supply a Monoscope signal to a Video Input
Activate the Convergence Mode.
Select the DF Function under the Conv. Coarse Mode.
Set Items “0 DFH” and “1 DFV” to the data values given in the DF Table.
Press “6” to activate CONV-MISC
Set “0 FPHS” and “1 DPHS” to data values given in the CONV-MISC Table.
Press “ENTER” to save data.
Exit the Conv. Mode.
DF
MENU-0-3-5-9-5
WS-48313 / WS-48413
Item Abbr.
WS-55313
SD Data
HD Data
1
DFH
-220
-220
2
DFV
-100
-100
CONVERGENCE MODE
Activate ……..MENU-0-3-5-9
Misc. ……………….……"6"
Coarse………………..…."5"
Fine ……………………..."4"
Color (R,G or B)……AUDIO
Item No………….…..VIDEO
Adjust/Move……….ADJUST
Cursor Toggle….…..ENTER
Save & Exit…..MENU (twice)
CONV MISC
(MENU-0-3-5-9-6)
Item
Abbr.
9
DPHS
10
DOFS
WS-55413 / WS-65313
WS-65413
SD Data
HD Data
-280
-250
-110
-95
SD & HD
1
34
To set the Lens position for optimum focus.
[Video Circuit]
Purpose
10. Lens Focus
Symptom: Poor focus
Measuring
Instrument
-----
Test Point
------
Note: This adjustment must be done before Electrostatic Focus. Perform this
adjustment for RED, GREEN, and BLUE monochrome pictures.
Ext. Trigger
------
Measuring
Range
Input Signal
-----
Input Terminal
Video Input
Monoscope
1. Supply a VIDEO signal (Monoscope).
2. Cover the Red and Blue Lens (producing a green raster).
3. Adjust the Green Lens for best focus at the center of the Monoscope pattern.
Note: Attach a white paper to the
screen center. During adjustment,
observe the picture on the screen
from inside for easier adjustment.
4. Repeat Steps 2 and 3 for the Red
and Blue monochrome pictures.
Page 34
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[CRT Circuit]
Purpose:
To set electrostatic focus to the optimum point.
11. Electrostatic Focus &
(Alignment Magnet)
Symptom:
Poor focus.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
------
Input Signal
Monscope & Crosshatch
Input Terminal
Video Input
Note: This adjustment must be performed after the Sub Contrast adjustment.
Alignment Magnet Adjustment (WS-48413, WS-55413 and WS-65413 Only)
This adjustment must be performed before Static Focus Adjustment
1. Set the display to the “Standard” mode (Format button)
2. Supply a Crosshatch with Center Dot signal to a Video Input.
3. Select a Green raster using the table below.
4. Roughly adjust Green Focus VR.
5. Rotate Green Focus VR CCW so the center dot is about 10mm diameter.
6. Adjust the Green 4 Pole Magnet for the roundest center dot.
7. Set the Green Focus VR for optimum focus.
8. Repeat the procedure with a Red raster and adjust the Red 4 Pole Magnet.
9. Use silicon to lock the magnets in place.
Static Focus Adjustment (All Models)
1. Supply a Monoscope signal to a Video Input
2. Activate A/V Reset
3. Select Red, Green or Blue rasters using the table below.
3. Set the Red, Green and Blue Focus VRs for optimum focus at the top center of
the picture..
Ra ster Color
Color Raster
Red
Green
Blue
Se le ction
Activation Code
MENU-0-3-5-9-1
MENU-0-3-5-9-2
MENU-0-3-5-9-3
[On Screen Display]
Purpose
To position the character display horizontally.
12.Character Position
Symptom:
Incorrect display position
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
Input Signal
Input Terminal
------
1.
2.
3.
4.
Supply a Monoscope signal to the Video or RF Input.
Select the Monoscope as the source for the main picture (Input button).
Activate the Service Mode, HR Function.
Use the Adjust Right/Left buttons to center the display horizontally.
(A = B)
5. Save data and exit the Service Mode..
Video Signal (HD/NTSC)
ANT-A/DTV
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
Page 35
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Conv/Defl]
Purpose:
To preset data controlling raster geometry
13. Geometry Preset
Symptom:
Raster distortion.
Measuring
Instrument
Test Point
Ext. Trigger
-----
Note: This procedure is usually only necessary if an E2PROM is replaced in the TV
Control or Convergence circuits.
Procedure
In the Circuit Adjustment and Coarse Convergence Modes pre-set the data to the
values given in the Tables below.
-----------
Measuring
Range
-----
Input Signal
NTSC & HD
Input Terminal
Video & DTV Inputs
Deflection Jungle
Menu-0-3-5-7
WS-48313
WS-55313 WS-55413 WS-65313 WS-65413
# Abbrev.
WS-48413
Item Abbr. NTSC HD NTSC HD NTSC HD NTSC HD NTSC HD
1
HWID
30
29
23
22
25
25
32
32
30
28
2
HKEY
24
25
24
25
24
25
24
25
24
25
7
VHGT
18
16
14
13
28
28
33
31
33
31
8
VLIN
5
5
5
5
5
5
7
7
7
7
9
VSCN
0
0
0
0
0
0
0
0
0
0
18
VPOS
31
31
31
31
31
31
31
31
31
31
36
PINA
10
8
10
8
10
8
10
8
10
8
COARSE CONV GREEN (MENU-0-3-5-9-5)
WS-48313
WS-55313 WS-55413
# Abbrev.
WS-48413
SD HD SD HD SD HD
1 HSTA
0
0
0
0
0
0
2 VSTA
0
0
0
0
0
0
3 SKEW
0
0
0
0
0
0
4
TILT
0
0
0
0
0
0
5 HWID
20
20
20
20
20
20
6 HLIN
0
0
0
0
10
10
7 SPCC
0
0
0
0
0
0
8 HKEY
23
20
15
10
20
20
9 TBPC -180 -160 -190 -165 -190 -180
10 VKEY
0
0
0
0
-4
8
11 VWID
30
20
30
20
30
20
12 VLIN
0
0
0
0
0
0
COARSE CONV RED (MENU-0-3-5-9-5)
WS-48313
WS-55313 WS-55413
# Abbrev.
WS-48413
SD HD SD HD SD HD
1 HSTA
50
50
50
50
50
50
2 VSTA
0
0
0
0
0
0
3 SKEW
5
5
5
5
5
5
4
TILT
0
0
0
0
0
0
5 HLIN -220 -200 -215 -195 -195 -180
6 HWID
0
0
0
0
-10
-5
7 VKEY -90 -90 -75 -75 -90 -70
8 VWID
0
0
0
0
0
0
9 VLIN
0
0
0
0
0
0
10 TBPC
20
20
20
20
20
20
11 SDBW 30
30
30
30
30
30
WS-65313
WS-65413
SD HD
50
50
0
0
0
0
0
0
-170 -150
10
10
-90 -75
0
10
0
0
20
20
30
30
WS-65313
WS-65413
SD HD
0
0
0
0
0
0
0
0
20
20
0
0
0
0
0
0
-200 -175
0
0
30
20
0
0
COARSE CONV BLUE (MENU-0-3-5-9-5)
WS-48313
WS-55313 WS-55413
# Abbrev.
WS-48413
SD HD SD HD SD HD
1 HSTA -50 -50 -50 -50 -50 -50
2 VSTA
0
0
0
0
0
0
3 SKEW
0
-5
0
-5
0
0
4
TILT
0
0
0
0
0
0
5 HLIN 220 200 220 205 195 180
6 HWID
0
0
0
0
-10 -15
7 VKEY
90
90
90
70
90
70
8 VWID
0
0
0
0
0
0
9 VLIN
0
0
0
0
0
0
10 TBPC
0
0
0
0
-20
0
11 SDBW -30 -30 -30 -30 -30 -30
Page 36
WS-65313
WS-65413
SD HD
-50 -50
0
0
0
0
0
0
175 160
10
10
80
75
0
0
0
0
-20
0
-30 -30
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Deflection Circuit]
Purpose:
To set the height, width and linearity of the raster.
14: Deflection Geometry
Height & Width Adjustment
Symptom:
Incorrect height, width and/or linearity.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
-----
Input Signal
Monoscope (NTSC & HD)
Input Terminal
Video & DTV Inputs
CIRCUIT ADJUST MODE
Activate …….. MENU-0-3-5-7
Function …...………..AUDIO
Item No. ……….…….VIDEO
Adjust Data ….…….ADJUST
Save Data …. ………ENTER
Exit …………..MENU (twice)
Preliminary:
1. DO NOT change the initial values for “#8 VLIN” in the Defl. Jungle Function.
2. DO NOT exceed the following VHGT adjustment ranges:
NTSC ... from -4 to +10
HD ... from -10 TO +5
NTSC Mode
1. Supply an NTSC Monoscope signal to a Video Input.
2. Select the Monoscope as the signal source.
3. Activate the Adjustment Mode, JNGL Function.
4. Select and adjust each of the following items.
• “7 VHGT” ... so the vertical marker sum = 4
• “1 HWD” ... so the horizontal marker sum = 7
5. Save data and Exit the Service Mode.
HD Mode
1. Supply an HD Monoscope signal to the DTV HD Inputs.
2. Select the DTV Inputs as the signal source (Input button)
3. Activate the Service Mode, Defl. Jungle Function.
4. Select and adjust each of the following items.
• “7 VHGT” ... so the vertical marker sum = 2
• “1 HWD” ... so the horizontal marker sum = 5
5. Save data and Exit the Service Mode.
Page 37
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Convergence Circuit]
Purpose:
To set the Convergence circuit geometry adjustments.
15. Convergence Geometry
Adjustment
Symptom:
Raster distortion at the top, bottom or sides of the picture.
Measuring
Instrument
Test Point
Ext. Trigger
Measuring
Range
-----
Note: Deflection Circuit Geometry must be performed before this adjustment.
------
NTSC mode
1. Select a Video Input with no signal.
2. Activate the Convergence Mode, Coarse Green.
3. Adjust the Coarse Green Items shown below for straight crosshatch lines.
4. Select the Fine Green Mode, a Cursor is displayed on the crosshatch.
5. Use the Cursor to adjust for straight crosshatch lines.
6. Exit the Convergence Mode.
----------
Input Signal
NTSC -- None
HD -- HD sync
Input Terminal
Video & DTV Inputs
CONVERGENCE MODE
Activate ……..MENU-0-3-5-9
Misc. ……………….……"6"
Coarse………………..…."5"
Fine ……………………..."4"
Color (R,G or B)……AUDIO
Item No………….…..VIDEO
Adjust/Move……….ADJUST
Cursor Toggle….…..ENTER
Save & Exit…..MENU (twice)
HD mode
1. Supply horizontal and vertical HD sync to the DTV Inputs and select the DTV
Inputs as the source.
Note: If an HD signal is not available, use the Conv. HD with No Signal
Procedure
2. Enter the Convergence Mode, Coarse Green.
3. Repeat NTSC Steps 3 through 6 in the HD mode.
CONV. HD W ITH NO SIGNAL
1. MENU-0-3-7-0
2. Set DTV Port to 1080i
3. MENU (Twice)
4. INPUT select DTV inputs
5. MENU-0-3-5-9
After Adjusting, set the
DTV Port to AUTO
Page 38
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Convergence Circuit]
Purpose:
To converge red, green and blue at the center of the screen
16. Centering and Static
Convergence
Symptom:
Color edging over the entire picture.
Measuring
Instrument
-----
Test Point
-----
Preliminary
Degauss the shield cover and bracket unit of the CRT assembly and chassis.
DO NOT degauss the CPM Assemblies.
Ext. Trigger
Measuring
Range
----------
Input Signal
NTSC -- Monoscope
HD -- Monoscope
Input Terminal
Video & DTV Inputs
CONVERGENCE MODE
Activate ……..MENU-0-3-5-9
Misc. ……………….……"6"
Coarse………………..…."5"
Fine ……………………..."4"
Color (R,G or B)……AUDIO
Item No………….…..VIDEO
Adjust/Move……….ADJUST
Cursor Toggle….…..ENTER
Save & Exit…..MENU (twice)
CAUTION: On models WS-48413, WS-55413 and WS-65413, Do Not adjust the
Alignment Magnets instead of the Centering Magnets.
HD mode
1. Supply an HD Monoscope signal to the DTV Inputs.
2. Select the DTV Inputs as the signal source (Input button).
3. Enter the Convergence Coarse mode.
4. Set the data for the “HSTA” and “VSTA” items to:
GREEN
RED
BLUE
HSTA = 0
HSTA = 50
HSTA = -50
VSTA = 0
VSTA = 0
VSTA = 0
5. In the Coarse Green mode:
• Center the Green Raster using the Green Centering Magnet.
• Rotate the Green Deflection Yoke to correct any tilt.
6. In the Coarse Red mode, use the Red Centering Magnet to converge
red on the green at the center of screen. Correct any red tilt with the Red
Deflection Yoke.
7. In the Coarse Blue mode, repeat Step 6 using the Blue Centering magnet and
the Blue Deflection Yoke.
8. Exit the Convergence mode.
SD mode
1. Supply an NTSC Monoscope signal to a Video Input.
2. Select the Monoscope as the signal source (Input button).
3. Enter the Convergence Coarse Green mode.
4. If needed, center the green raster using “1 HSTA” and “2 VSTA” adjustments.
5. In the Coarse Red mode, use “1 HSTA” and “2 VSTA” adjustments to converge
the red on the green at the center of the screen.
6. In the Coarse Blue mode, repeat step 5 to converge the blue of the green.
7. Exit the Convergence Mode
Page 39
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Convergence Circuit]
Purpose:
17. Coarse Convergence
Symptom:
Measuring
Instrument
-----
Test Point
------
Ext. Trigger
------
Measuring
Range
-----
SD mode
1. Select an External Input with no signal.
2. Activate the Convergence Mode, Coarse Red.
3. Adjust the Items shown below to converge the red on the green.
4. Select Coarse Blue mode.
5. Adjust the Items shown below to converge the blue on the green.
Note: If center convergence shifts, use red and blue Items “0 HSTA” and
“1 VSTA” to correct the shift.
6. Exit the Convergence Mode.
Input Signal
NTSC -- None
HD -- HD sync
Input Terminal
Video & HD Inputs
CONVERGENCE MODE
Activate ……..MENU-0-3-5-9
Misc. ……………….……"6"
Coarse………………..…."5"
Fine ……………………..."4"
Color (R,G or B)……AUDIO
Item No………….…..VIDEO
Adjust/Move……….ADJUST
Cursor Toggle….…..ENTER
Save & Exit…..MENU (twice)
To converge red and blue on green at the edges of the
screen.
Color edging at the top, bottom and sides of the screen.
HD mode
1. Supply horizontal and vertical HD sync to the DTV Inputs and select the DTV
Inputs as the source.
Note: If an HD signal is not available, use the Conv. HD with No Signal
Procedure.
2. Repeat SD Steps 2 through 5 in the HD mode.
3. Exit the Convergence mode.
CONV. HD WITH NO SIGNAL
1. MENU-0-3-7-0
2. Set DTV Port to 1080i
3. MENU (Twice)
4. INPUT select DTV inputs
5. MENU-0-3-5-9
After Adjusting, set the
DTV Port to AUTO
Page 40
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[Convergence Circuit]
Purpose:
To converge red, green and blue at the edges of the screen
18. Fine Convergence
Symptom:
Color edging at the edges of the picture.
Measuring
Instrument
Test Point
Ext. Trigger
--------------
Measuring
Range
-----
Input Signal
NTSC -- None
HD -- HD sync
Input Terminal
Video & DTV Inputs
CONVERGENCE MODE
Activate ……..MENU-0-3-5-9
Misc. ……………….……"6"
Coarse………………..…."5"
Fine ……………………..."4"
Color (R,G or B)……AUDIO
Item No………….…..VIDEO
Adjust/Move……….ADJUST
Cursor Toggle….…..ENTER
Save & Exit…..MENU (twice)
SD Fine Adjustment
1. Select an External Input, no signal.
2. Activate the Convergence Mode, Fine Red.
3. Use the Cursor to converge red on the green.
4. Select the Fine Blue mode.
5. Use the Cursor to converge blue on the green.
6. Exit the Convergence mode.
HD Fine Adjustment
1. Supply an HD signal (sync only) to the DTV inputs and select DTV with the
“Audio” button.
Note: If an HD signal is not available, use the Conv. HD with No Signal
Procedure.
2. Repeat SD Fine Adjustment Steps 2 through 6, in the HD mode.
CONV. HD WITH NO SIGNAL
1. MENU-0-3-7-0
2. Set DTV Port to 1080i
3. MENU (Twice)
4. INPUT select DTV inputs
5. MENU-0-3-5-9
After Adjusting, set the
DTV Port to AUTO
Page 41
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CHIP PARTS REPLACEMENT
Some resistors, shorting jumpers (0 Ohm resistors),
ceramic capacitors, transistors and diodes are chip parts.
The following precautions should be taken when replacing
these parts.
Cautions:
1. Use a fine tipped, well insulated soldering iron
(approximately 30 watts), and tweezers.
2. Melt the solder and remove the chip parts
carefully so as not to tear the copper foil from
the printed circuit board.
3. Discard removed chips; do not reuse them.
4. Do not apply heat for more than 3 (three)
seconds to new chip parts.
5. Avoid using a rubbing stroke when soldering.
6. Take care not to scratch, or damage the chip
parts when soldering.
7. Supplementary cementing is not required.
Chip Parts Removal (Transistors)
1. Melt the solder of one lead and lift the side of
that lead upward.
2. Simultaneously melt the solder of the other
two leads and lift the part from the PCB.
Chip Parts Removal (Resistors, Capacitors, etc.)
1. Grasp the part with tweezers. Melt the solder
at both sides alternately, and remove one side
of the part with a twisting motion.
2. Melt the solder at the other side and remove
the part.
Replacement
1. Presolder the contact points on the circuit
pattern.
2. Press the part downward with tweezers and
apply the soldering iron as shown.
Page 42
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
RELACEMENT PARTS
Parts Ordering
To expedite delivery of replacement parts orders, specify the following:
1. Model Number/Serial Number
2. Part Number and description
3. Quantity
Note: Unless complete information is supplied, delay in processing of orders will result.
Critical and Warranty Parts Designation
Critical Electrical Components are indicated by Bold Type in the Parts List, and in the schematic
diagrams by shading.
Warranty Return Parts are indicated in the Parts List with an (*).
Parts Tolerance Codes
Refer to the following chart for tolerance characteristics of electrical components.
MARK
B
C
D
F
G
J
K
Tolerance %
± 0.1
± 0.25
± 0.5
±1
±2
±5
± 10
MARK
M
N
V
X
Z
P
Q
Tolerance %
± 20
± 30
± 10
+ 40
+ 80
+ 100
+ 30
-20
-20
-0
-10
MARK
M
N
V
X
Z
Tolerance (pF)
± 0.1
± 0.25
± 0.5
±1
±2
Page 43
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
QUICK REFERENCE FOR COMMON REPLACEMENT PARTS
CRT ASSEMBLIES
CRT-ASSY
ASSY-CRT-RED
ASSY-CRT-GREEN
ASSY-CRT-BLUE
WS-48313
251C222070
251C222080
251C222090
WS-48413
251C223040
251C223050
251C223060
WS-55313
251C223010
251C223020
251C223030
WS-55413
251C223070
251C223080
251C223090
WS-65313
251C222040
251C222050
251C222060
WS-65413
251C222040
251C222050
251C222060
PRINTED CIRCUIT BOARDS
PCB
WS-48313
WS-48413
WS-55313
WS-55413
WS-65313
WS-65413
930B899003
930B899001
MAIN
ç
ç
ç
ç
930B90001
POWER
ç
ç
ç
ç
ç
SIGNAL 930B901001-48 930B901002-48 930B901001-55 930B901002-55 930B901001-65 930B901002-65
93B0902001
TERMINAL
ç
ç
ç
ç
ç
934C062001
CRT
ç
ç
ç
ç
ç
934C063001
DOUBLER
ç
ç
ç
ç
ç
935D738001
935D738002
935D738001
935D738002
935D738001
935D738002
PREAMP
935D739001
FRONT
ç
ç
ç
ç
ç
935D740001
CONTROL
ç
ç
ç
ç
ç
REMOTE CONTROL
\
260P11601
260P117010
Remote Control
Remote Control
WS-48313 / WS-55313 / WS-65313
WS-48413 / WS-55413 / WS-65413
HIGH VOLTAGE / DEFLECTION COMPONENTS
Q5A51
T5A51
261P082010
334P281010
330P293010
330P293020
453B136010
453B136020
HV-OUT 2SK2771-O1R
TRANS-FLYBACK
DEFL-YOKE
DEFL-YOKE
CAP-ANODE-LONG [R]
CAP-ANODE-LONG [GB]
WS-55413 / WS-65313 / WS-65413
WS-48313 / WS-48413 / WS-55313
MISCELLANEOUS
MODEL
WS-48313
WS-48413
WS-55313
WS-55413
WS-65313
WS-65413
MIRROR
767D072040
"
767D072050
767D072030
767D048090
"
Page 44
LENTICULAR
SCREEN
491P138020
"
491P103030
"
491P105050
"
FRESNEL
LENS
491P139020
"
491P104030
"
491P106080
"
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
[#]
TUBES
251C222040
251C222050
251C222060
251C222070
251C222080
251C222090
251C223010
251C223020
251C223030
251C223040
251C223050
251C223060
251C223070
251C223080
251C223090
ASSY-CRT-RED
ASSY-CRT-GREEN
ASSY-CRT-BLUE
ASSY-CRT-RED
ASSY-CRT-GREEN
ASSY-CRT-BLUE
ASSY-CRT-RED
ASSY-CRT-GREEN
ASSY-CRT-BLUE
ASSY-CRT-RED
ASSY-CRT-GREEN
ASSY-CRT-BLUE
ASSY-CRT-RED
ASSY-CRT-GREEN
ASSY-CRT-BLUE
INTEGRATED CIRCUITS
IC2C00 275P989010
IC2D00 270P974010
IC2D02 261P135010
IC2D04 271P004010
IC2K01 270P623010
IC2K02 275P533010
IC2K04 275P718010
IC2K05 275P718010
IC2L01 275P937010
IC2M01 275P947010
IC2M02 270P992020
IC2MD1 272P379020
IC2N01 275P938010
IC2P01 275P938010
IC2R01 271P005010
IC2V00 275P733010
IC3A01 275P731020
IC3E01 270P750010
IC3J01 270P838010
IC3J02 270P838010
IC3J03 270P838010
IC3J04 270P838010
IC4B01 270P261020
IC5A00 267P163010
IC5A01 272P237010
IC5A02 266P727040
IC5A03 270P704010
IC6B01 270P667010
IC6G01 270P667010
IC6R01 270P667010
IC7A00 275P942030
IC7AAA 275P981010
IC7B01 270P706020
IC7C01 275P533010
IC7D01 275P278010
IC7D02 270P818020
IC7D03 267P172010
IC7E00 275P451010
IC7E01 275P560010
IC7E02 275P560010
IC7E03 275P560010
IC-C-MOS - MAX3223ECAP
IC-C-MOS - SII907B
FET-HEX - IRF7313
IC - CM1208-08MS
IC - CXA2069Q
IC-C-MOS - M24C64WM6T
IC-C-MOS - TC74HC4053FT
IC-C-MOS - TC74HC4053FT
IC-C-MOS - MM1519XQ
IC-C-MOS - UPD64083
IC - BA25BC0FP
IC - LM1881MX (NSC)
IC-C-MOS - TA1340F
IC-C-MOS - TA1340F
IC - AN15851A
IC-C-MOS - CXA2150AQ
IC-C-MOS - MSP3445G-QI-B8-V3
IC - LA4663
IC-C-MOS - NJM2520M
IC-C-MOS - NJM2520M
IC-C-MOS - NJM2520M
IC-C-MOS - NJM2520M
IC - TDA8177
HIC - MSPAD401
IC - LA6324N
IC - UPC339C/LM339N
IC - LM4040BIZ-10.0
IC - TDA6120Q
IC - TDA6120Q
IC - TDA6120Q
IC-C-MOS
IC-C-MOS - 24LCS22AT/SN
IC - MAX823REUK
IC-C-MOS - M24C64WM6T
IC-C-MOS - TC74LVX14FT
IC - CXA3506R
HIC - AF-9395A
IC-C-MOS - TC74HC4066AFN-ELP
IC-C-MOS - ADS931E
IC-C-MOS - ADS931E
IC-C-MOS - ADS931E
5&6
5&6
5&6
1
1
1
3
3
3
2
2
2
4
4
4
Ref #
Part #
Part Name & Description
IC7H00
IC7H07
IC7K21
IC7M00
IC7N01
IC7N11
IC7N21
IC7N31
IC7N41
IC7N61
IC7P01
IC7Q01
IC8C01
IC8C02
IC8D00
IC8D01
IC8E00
IC8E01
IC8E02
IC8E03
IC9A20
IC9A21
IC9A50
IC9AAA
IC9B02
IC9C01
IC9C11
IC9C21
IC9C31
IC9C41
IC9C51
IC9C61
275P963010
270P992010
270P831010
275P982010
270P348010
275P236020
275P769010
275P769010
274P901010
274P901010
275P943080
275P657050
267P173010
267P173010
275P595010
275P222020
270P751010
270P751010
270P751010
275P721010
267P164010
270P816010
267P161010
270P677010
270P668020
270P928010
270P928010
270P677010
270P999010
270P677010
270P990010
270P677010
IC-C-MOS - DPM5
IC - BA18BC0FP
IC-C-MOS - OPA2350PA
IC - MT48LC2M32B2-7
IC - TLC2932IPW
IC-C-MOS - TC74LVX244FT
IC-C-MOS - TC74AC157FT
IC-C-MOS - TC74AC157FT
IC-C-MOS - TC74HCT7007AF
IC-C-MOS - TC74HCT7007AF
IC-C-MOS - PIC18F252T-I/SO
IC-C-MOS - 24LC256T-I/SN
HIC - STK394-250
HIC - STK394-250
IC-C-MOS - CM0022AF
IC-C-MOS - M24C32MN6T
IC - TL084CD
IC - TL084CD
IC - TL084CD
IC-C-MOS - CD0031AM
HIC - TNY264P
IC - NJM431L
HIC - STR-F6428S
IC - BA033FP
IC - SI-8050S
IC - BA17809FP
IC - BA17809FP
IC - BA033FP
IC - NJM2370R09
IC - BA033FP
IC - SI-8120JD
IC - BA033FP
TRANSISTORS
CHIP Type Transistors (Listed by Part No.)
Part No.
Description
260P817010 2SA1037K-Q
260P817050 2SA1037K-R,S/2SB709AI-R,S
260P817080 2SA1037K-R,S
260P818050 2SC2412K-R,S/2SD601AI-R,S
260P835030 2SC2413K-Q
261P801010 2SA1252-5,6
Q2V30
Q4B01
Q5A01
Q5A02
Q5A03
Q5A04
Q5A05
Q5A07
Q5A07
Q5A08
Q5A09
Q5A09
Q5A10
Q5A20
Q5A31
Page 45
Conventional Type Transistors (Listed by Part No.)
Part No.
Description
260C004020 TR - 2SC1740S-S/2SC3311A-S
260C004020 TR - 2SC1740S-S/2SC3311A-S
261P126010 TR - 2SD2052
260P561020 TR - 2SA1371-E
260P386010 TR - 2SC2230-GR
260C004010 TR - 2SC1740S-R,S/2SC3311A-R,S
260C004050 TR - 2SA933S-R,S/2SA1309A-R,S
260C004010 TR - 2SC1740S-R,S/2SC3311A-R,S
260C416030 TR - 2SC2274-F/2SC2274K-F
260C004010 TR - 2SC1740S-R,S/2SC3311A-R,S
260C004010 TR - 2SC1740S-R,S/2SC3311A-R,S
260C255040 TR - 2SA950-Y
260C004050 TR - 2SA933S-R,S/2SA1309A-R,S
260C004050 TR - 2SA933S-R,S/2SA1309A-R,S
261P122010 TR - 2SC5778
[#]
246
246
246
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
Q5A32
Q5A33
Q5A34
Q5A35
Q5A36
Q5A37
Q5A38
Q5A39
Q5A40
Q5A51
Q5H01
Q5H03
Q5H04
Q5H05
Q5H06
Q5H09
Q5H10
Q5H11
Q5H12
Q5H13
Q5K00
Q5K01
Q5K02
Q5K03
Q6B01
Q6B02
Q6B03
Q6G01
Q6R01
Q7B12
Q7B22
Q7K21
Q9A51
Q9A52
Q9A54
Q9A55
Q9B01
261P127010
260C004010
260P561020
260P386010
260P630010
260C004010
260C004010
260C004050
260C004050
261P082010
260C001040
260C001040
260C001040
260C001040
260C001060
260C001030
260C001060
260P644040
260P647040
260C001060
260P664030
260P664030
260C004020
260C004050
260C001010
260C001050
260C001050
260C001010
260C001010
261P114010
261P114010
260C004010
260C004010
260C004010
260C004010
260C004010
260C004010
TR - 2SK2774-01
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SA1371-E
TR - 2SC2230-GR
TR - 2SD2012
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SA933S-R,S/2SA1309A-R,S
TR - 2SA933S-R,S/2SA1309A-R,S
TR - 2SK2771-01R
TR - 2SC2603-G/2SC1740S-E
TR - 2SC2603-G/2SC1740S-E
TR - 2SC2603-G/2SC1740S-E
TR - 2SC2603-G/2SC1740S-E
TR - 2SA1115-F/2SA933S-S
TR - 2SC2603-F,G/2SC1740S-S,E
TR - 2SA1115-F/2SA933S-S
TR - 2SA1535-R
TR - 2SC3944-R
TR - 2SA1115-F/2SA933S-S
TR - 2SC4636
TR - 2SC4636
TR - 2SC1740S-S/2SC3311A-S
TR - 2SA933S-R,S/2SA1309A-R,S
TR - 2SC2603-E,F/2SC1740S-R,S
TR - 2SA1115-E,F/2SA933S-R,S
TR - 2SA1115-E,F/2SA933S-R,S
TR - 2SC2603-E,F/2SC1740S-R,S
TR - 2SC2603-E,F/2SC1740S-R,S
TR - 2SA1585STPR
TR - 2SA1585STPR
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC1740S-R,S/2SC3311A-R,S
D2W01
D2W02
D2W03
D2W04
D4B01
D4B04
D5A01
D5A02
D5A03
D5A12
D5A13
D5A14
D5A33
D5A34
D5A35
D5A36
D5A37
D5A51
D5A52
D5A53
264P828010
264P828010
264P828010
264P828010
264D056020
264P045080
264P045080
264D056020
264P045080
264P045080
264P045080
264P045080
262P086010
264P460060
264P045080
264P045080
264P521010
262P039010
264P899010
264P466040
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
DIODE - S5500D/EM1Z/ERB12-02RK
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - S5500D/EM1Z/ERB12-02RK
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 31DF2-FC5
DIODE - EQA02-05C/RD5.1EB1
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - EU 1Z
DIODE - BYW96E/20
DIODE - BYV26E
DIODE - EQA02-15AB/RD16EB1
DIODES
[#]
246
246
Ref #
Part #
Part Name & Description
D5A54
D5A55
D5A56
D5A57
D5A58
D5A60
D5H01
D5H02
D5K01
D5K02
D5K03
D5K10
D5K11
D5K12
D6B00
D6B07
D6B08
D6G00
D6G07
D6G08
D6R00
D6R07
D6R08
D7AAA
D7K21
D7K22
D7L21
D8C03
D8C04
D9A01
D9A22
D9A24
D9A28
D9A29
D9A30
D9A31
D9A53
D9A54
D9A55
D9A56
D9A57
D9A58
D9A60
D9A61
D9A65
D9A66
D9A67
D9A68
D9A69
D9B01
D9B02
D9B05
D9B07
D9C51
262P085010
262P085010
264P045080
264P521010
264P045080
264P465060
264P045080
264P045080
264P528030
264P543010
264P543010
264P528030
264P528030
262P085010
262P063010
262P063010
262P063010
262P063010
262P063010
262P063010
262P063010
262P063010
262P063010
262P805050
268P100010
264P045080
264P212020
264P486060
264P486060
262P031010
264P825040
264P045080
264P045080
264P461050
262P097010
262P097010
264P045080
262P085010
264P045080
262P083010
264P899010
262P088010
262P083010
262P086010
264P045080
264P045080
264P461050
264P469070
264P527020
264P045080
264P045080
262P084010
264P484030
262P087010
DIODE - 11EFS2N-TA2B5
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - EU 1Z
DIODE - 1S2076A/1S2471OM
DIODE - EQA02-12B/RD13EB2
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - RP 1H
DIODE - EG01
DIODE - EG01
DIODE - RP 1H
DIODE - RP 1H
DIODE - 11EFS2N-TA2B5
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
D-CHIP - UDZS5.1B
DIODE-PHOTO - SFH235FA
DIODE - 1S2076A/1S2471OM
D-LED - LN31GPH
DIODE - RD9.1FB3
DIODE - RD9.1FB3
DIODE - D6SB80
DIODE - ERA15-08
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - EQA02-06B/RD5.6EB3
DIODE - 11EQS06N-TA2B5
DIODE - 11EQS06N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - FSF05A20
DIODE - BYV26E
DIODE - 31DF4-FC5
DIODE - FSF05A20
DIODE - 31DF2-FC5
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - EQA02-06B/RD5.6EB3
DIODE - EQA02-28A/RD27EB4
DIODE - AK04
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 31DQ06
DIODE - RD5.6FB2
D-CHIP - EC21QS04-TE12L
Page 46
[#]
4-6
246
246
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
COILS
L1A30
L1A31
L1B30
L1B31
L2AGA
L2AJA
L2AKA
L2ANA
L2APA
L2ARA
L2ATA
L2AYA
L2AZA
L2K05
L2K42
L2K46
L2K55
L2L28
L2M22
L2M31
L2M32
L2M38
L2M45
L2M46
L2M50
L2M53
L2M81
L2MA0
L2MA1
L2MD1
L2N01
L2N25
L2NA1
L2NA2
L2NA3
L2NC0
L2NC1
L2P01
L2P22
L2P25
L2P31
L2P32
L2P41
L2R28
L2V19
L2V55
L2V61
L2W02
L2W03
L2W04
L3A10
L3A49
L3J01
L3J20
L3J40
L4B01
L4B02
L5A22
321C114010
325C461030
321C114010
325C461030
409P864010
409P864010
409P864010
409P864010
409P864010
409P864010
409P864010
409P864010
409P864010
409P777080
325C461030
325C462080
325C462080
325C461030
325C461050
409P777080
325C461050
409P777080
409P777080
409P777080
325C461000
325C461030
409P777080
325C461050
325C461030
325C461030
325C461030
325C462020
325C461030
325C461080
325C461030
325C461030
325C461080
325C461030
325C461050
325C462020
325C462020
325C461050
325C462020
325C461030
325C461010
325C461010
325C461010
409P923060
409P923060
409P923060
409P923060
409P923060
325C461030
325C461030
409P777020
321C130010
321C130090
333P059020
COIL-RF - 2200MH-J
COIL-PEAKING - 10MH-K
COIL-RF - 2200MH-J
COIL-PEAKING - 10MH-K
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - ACB2012M600/BLM21A601S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
COIL-PEAKING - 180MH-J
COIL-PEAKING - 180MH-J
COIL-PEAKING - 10MH-K
COIL-PEAKING - 15MH-K
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 15MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 5.6MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 15MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 56MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 27MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 27MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 15MH-K
COIL-PEAKING - 56MH-K
COIL-PEAKING - 56MH-K
COIL-PEAKING - 15MH-K
COIL-PEAKING - 56MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 6.8MH-K
COIL-PEAKING - 6.8MH-K
COIL-PEAKING - 6.8MH-K
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21A05
COIL-RF - 2MH
COIL-RF - 10MH-K
COIL-HORIZ-LIN
[#]
Ref #
Part #
Part Name & Description
L5A34
L5A51
L5A54
L7A16
L7A19
L7A88
L7A90
L7A91
L7A99
L7ACC
L7CA3
L7D30
L7D31
L7D41
L7D42
L7D90
L7E00
L7E11
L7E12
L7E13
L7E14
L7E15
L7G51
L7G66
L7G81
L7H01
L7H04
L7H29
L7H49
L7H73
L7H76
L7J13
L7J23
L7J38
L7J44
L7K01
L7M90
L7N01
L7N02
L7N11
L7N21
L7N31
L7N41
L7N61
L7P01
L7RF1
L8C01
L8C02
L8D01
L8D02
L8D03
L8D04
L8D05
L8D06
L8D07
L8D08
L8G00
L8G01
L9A20
L9A21
321C130010
321C151040
411D009020
409P777050
409P777050
409P777050
409P777050
409P777050
409P777050
409P777080
325C146090
325C241030
325C241030
325C241030
409P777080
409P777080
409P777080
325C241030
409P777080
325C241030
409P777080
325C241030
325C241030
325C241030
325C241030
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
325C241030
409P777080
409P777080
325C121030
409P777080
325C241030
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777050
409P777050
321C141070
321C141070
409P777080
409P777080
409P777080
409P777080
325C461030
409P777080
409P777080
325C461030
409P777080
409P777080
321C141070
321C141070
COIL-RF - 2MH
COIL-RF - 12MH-K
CORE-FERRITE
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 33MH-J
COIL-CHIP - 10MH-K
COIL-CHIP - 10MH-K
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
COIL-CHIP - 10MH-K
COIL-CHIP - 10MH-K
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
COIL-RF - 22MH-K
COIL-RF - 22MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-RF - 22MH-K
COIL-RF - 22MH-K
Page 47
[#]
246
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
L9A50 411D009020
L9A52 411D009020
L9A53 321C141010
L9A54 411D009020
L9A55 321C142030
L9A56 411D009020
L9A57 321C141070
L9A62 321C141010
L9A63 321C141010
L9A64 321C141010
L9AAA 325C462020
L9B03 321C141070
L9B04 351P247010
L9B05 321C141030
L9C51 321C141070
L9C52 351P244010
L9C53 321C141070
L9D00 351P243010
L9D01 351P243010
L9D02 351P223010
LC2J40 409P777020
LC2J41 409P777020
LC2J42 409P777020
LC2J43 409P777020
LC3J41 409P777020
LC7CBA 409P876020
LC7CCA 409P876020
LC7CDA 409P876020
LC7D02 409P875090
LC7D05 409P875090
LC7D10 409P876020
LC7D11 409P876020
LC7D12 409P876020
LC7D13 409P876020
LC7D14 409P876020
LC7E10 409P876020
LC7E11 409P876020
LC7E12 409P876020
LC7E13 409P876020
LC7E14 409P876020
LC7G01 409P876020
LC7G02 409P876020
LC7G03 409P876020
LC7G04 409P876020
LC7G05 409P876020
LC7G06 409P876020
LC7G07 409P876020
LC7G08 409P876020
LC7G09 409P875090
LC7G10 409P875090
LC7G11 409P876020
LC7G12 409P876020
LC7G13 409P876020
LC7G14 409P876020
LC7G15 409P876020
LC7G16 409P876020
LC7G17 409P876020
Part Name & Description
[#]
CORE-FERRITE
CORE-FERRITE
COIL-RF - 6.8MH-M
CORE-FERRITE
COIL-RF - 68MH-K
CORE-FERRITE
COIL-RF - 22MH-K
COIL-RF - 6.8MH-M
COIL-RF - 6.8MH-M
COIL-RF - 6.8MH-M
COIL-PEAKING - 56MH-K
COIL-RF - 22MH-K
COIL-CHOKE - 150UH
COIL-RF - 10MH-K
COIL-RF - 22MH-K
COIL-CHOKE - CD-C-1010-101
COIL-RF - 22MH-K
FILTER-LINE - CD-N-2637F-152
FILTER-LINE - CD-N-2637F-152
FILTER-LINE - SLF15N0601
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - ELKE103FA
EMI-F-CHIP - ELKE103FA
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - ELKE103FA
EMI-F-CHIP - ELKE103FA
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
EMI-F-CHIP - CNF20C470S/CKD510JB1H470S
Ref #
Part #
T5A31
T5A32
T5A51
T9A20
T9A50
349P221010
336P040010
334P281010
350P806010
350P807010
Part Name & Description
[#]
TRANSFORMERS
TRANS-HORIZ
TRANS-HORIZ-DRIVE
TRANS-FLYBACK
TRANS-POWER
TRANS-POWER
VARIABLE RESISTORS
129P070010
RV9D00 265P100020
VR-FOCUS - MT010315-157
VARISTOR - ERZV10D271CS
RESISTORS
CHIP Type Resistors (Listed by Value)
Part No.
Value
Part No.
103P509050
1/16W 0OHM
103P502070
103P508040
1/16W 2.2-J
103P502080
103P400050
1/8W 22-J
103P493020
103P500050
1/16W 22-J
103P493030
103P500070
1/16W 33-J
103P502090
103P500080
1/16W 39-J
103P493050
103P500090
1/16W 47-J
103P503000
103P501000
1/16W 56-J
103P493060
103P501010
1/16W 68-J
103P503010
103P794060
1/16W 75-F
103P493090
103P501020
1/16W 82-J
103P503020
103P401030
1/8W 100-J
103P494010
103P501030
1/16W 100-J
103P503030
103P501040
1/16W 120-J
103P494020
103P401050
1/8W 150-J
103P503040
103P490050
1/16W 150-F
103P494050
103P501050
1/16W 150-J
103P503050
103P490070
1/16W 180-F
103P503060
103P501060
1/16W 180-J
103P494090
103P401080
1/8W 270-J
103P503070
103P501070
1/16W 220-J
103P503080
103P491000
1/16W 240-F
103P503090
103P501080
1/16W 270-J
103P504000
103P491020
1/16W 300-F
103P504010
103P501090
1/16W 330-J
103P504020
103P491040
1/16W 360-F
103P496000
103P491050
1/16W 390-F
103P504030
103P502000
1/16W 390-J
103P504040
103P502010
1/16W 470-J
103P504050
103P491090
1/16W 560-F
103P504060
103P502020
1/16W 560-J
103P496080
103P492000
1/16W 620-F
103P496090
103P492010
1/16W 680-F
103P504070
103P502030
1/16W 680-J
103P509090
103P492030
1/16W 820-F
103P504080
103P502040
1/16W 820-J
103P504090
103P492050
1/16W 1K-F
103P505000
103P502050
1/16W 1K-J
103P505090
103P492060
1/16W 1.1K-F
103P506000
103P502060
1/16W 1.2K-J
103P506010
103P402070
1/8W 1.5K-J
103P506070
103P492090
1/16W 1.5K-F
Page 48
Value
1/16W 1.5K-J
1/16W 1.8K-J
1/16W 2K-F
1/16W 2.2K-F
1/16W 2.2K-J
1/16W 2.7K-F
1/16W 2.7K-J
1/16W 3K-F
1/16W 3.3K-J
1/16W 3.9K-F
1/16W 3.9K-J
1/16W 4.7K-F
1/16W 4.7K-J
1/16W 5.1K-F
1/16W 5.6K-J
1/16W 6.8K-F
1/16W 6.8K-J
1/16W 8.2K-J
1/16W 10K-F
1/16W 10K-J
1/16W 12K-J
1/16W 15K-J
1/16W 18K-J
1/16W 22K-J
1/16W 27K-J
1/16W 30K-F
1/16W 33K-J
1/16W 39K-J
1/16W 47K-J
1/16W 56K-J
1/16W 62K-F
1/16W 68K-F
1/16W 68K-J
1/16W 75K-J
1/16W 82K-J
1/16W 100K-J
1/16W 120K-J
1/16W 680K-J
1/16W 820K-J
1/16W 1M-J
1/16W 3.3M-J
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
Ref #
R2J21
R2J31
R3E02
R3E04
R3E05
R3E06
R3E09
R3E11
R3E12
R3E14
R3E15
R3E16
R4B01
R4B02
R4B03
R4B10
R4B12
R4B13
R4B14
R4B16
R4B17
R4B23
R4B24
R4B25
R4B26
R4B27
R5A00
R5A01
R5A02
R5A03
R5A04
R5A05
R5A06
R5A07
R5A08
R5A09
R5A10
R5A11
R5A12
R5A13
R5A14
R5A15
R5A16
R5A17
R5A18
R5A19
R5A20
R5A21
R5A22
R5A23
R5A24
R5A25
R5A26
R5A27
R5A28
R5A29
R5A30
R5A31
Conventional Resistors (By Ref #)
Part #
Part Name & Description
109D151050 R-CARBON - 1/4W 75-J
109D151050 R-CARBON - 1/4W 75-J
103P712080 R-CARBON - 1/4W 1.8K-J
103P712080 R-CARBON - 1/4W 1.8K-J
103P714060 R-CARBON - 1/4W 56K-J
103P713080 R-CARBON - 1/4W 12K-J
109D151010 R-CARBON - 1/4W 2.2-J
109D151010 R-CARBON - 1/4W 2.2-J
109D151010 R-CARBON - 1/4W 2.2-J
109D151010 R-CARBON - 1/4W 2.2-J
103P713050 R-CARBON - 1/4W 6.8K-J
103P713050 R-CARBON - 1/4W 6.8K-J
103P465040 R-METAL - 1/4W 16K-F
103P465040 R-METAL - 1/4W 16K-F
103P713090 R-CARBON - 1/4W 15K-J
103C188040 R-METAL - 2W 2.2-J
103C188040 R-METAL - 2W 2.2-J
103P466000 R-METAL - 1/4W 2.4K-F
103P466000 R-METAL - 1/4W 2.4K-F
109P095010 R-METAL-LIN - 1/4W 5.1K-J
103P711090 R-CARBON - 1/4W 330-J
103P411070 R-CARBON - 1/4W 220-J
103P712050 R-CARBON - 1/4W 1K-J
103P712050 R-CARBON - 1/4W 1K-J
103P713030 R-CARBON - 1/4W 4.7K-J
103P465040 R-METAL - 1/4W 16K-F
103P711030 R-CARBON - 1/4W 100-J
103P713010 R-CARBON - 1/4W 3.3K-J
103P711030 R-CARBON - 1/4W 100-J
103P713010 R-CARBON - 1/4W 3.3K-J
103P462040 R-METAL - 1/4W 910-F
103P713010 R-CARBON - 1/4W 3.3K-J
103P712050 R-CARBON - 1/4W 1K-J
103P714080 R-CARBON - 1/4W 82K-J
103P714050 R-CARBON - 1/4W 47K-J
103P714040 R-CARBON - 1/4W 39K-J
103P714040 R-CARBON - 1/4W 39K-J
103P713070 R-CARBON - 1/4W 10K-J
103P712050 R-CARBON - 1/4W 1K-J
103P464020 R-METAL - 1/4W 2.4K-F
103P464030 R-METAL - 1/4W 5.6K-F
103P713030 R-CARBON - 1/4W 4.7K-J
103P714010 R-CARBON - 1/4W 22K-J
103P712050 R-CARBON - 1/4W 1K-J
103P712050 R-CARBON - 1/4W 1K-J
103P712010 R-CARBON - 1/4W 470-J
103P714050 R-CARBON - 1/4W 47K-J
103P713030 R-CARBON - 1/4W 4.7K-J
103P714010 R-CARBON - 1/4W 22K-J
103P713070 R-CARBON - 1/4W 10K-J
103P714070 R-CARBON - 1/4W 68K-J
103P464030 R-METAL - 1/4W 5.6K-F
103P464030 R-METAL - 1/4W 5.6K-F
103P713070 R-CARBON - 1/4W 10K-J
103P715010 R-CARBON - 1/4W 150K-J
103P714040 R-CARBON - 1/4W 39K-J
103P714040 R-CARBON - 1/4W 39K-J
103P712080 R-CARBON - 1/4W 1.8K-J
[#]
[#]
Ref #
Part #
Part Name & Description
R5A32
R5A33
R5A34
R5A35
R5A36
R5A36
R5A37
R5A37
R5A38
R5A40
R5A41
R5A42
R5A43
R5A44
R5A46
R5A47
R5A48
R5A49
R5A50
R5A51
R5A52
R5A53
R5A54
R5A56
R5A57
R5A58
R5A59
R5A60
R5A61
R5A62
R5A62
R5A63
R5A64
R5A65
R5A66
R5A67
R5A68
R5A69
R5A70
R5A71
R5A72
R5A73
R5A74
R5A75
R5A76
R5A77
R5A78
R5A79
R5A81
R5A82
R5A83
R5A84
R5A85
R5A86
R5A87
R5A88
R5A89
R5A90
R5A91
R5A92
103P713070
103P463060
103P711000
103P142010
103C393020
103C393030
103C393020
103C393030
103C197040
103P714090
103P715020
103P713070
103P714010
103P712090
103C391050
103P714080
103P714050
103P711030
103P714050
103P712050
103P713010
103P713070
103P714010
103P715060
103P711030
103P464080
103P461070
103P464000
103P465010
103P711030
103P711070
103P466080
103P712010
103P141030
103P466010
103P465080
103P463050
103P462010
103P463070
103P713070
103P463050
103P713070
103P713070
103P713070
103P713070
103P711090
103P714010
103P713030
103P711030
103P370090
103P464070
103P464070
103P710070
103P466030
103P142060
103P714010
103P466090
103P711060
103P467030
103P465070
R-CARBON - 1/4W 10K-J
R-METAL - 1/4W 3K-F
R-CARBON - 1/4W 56-J
R-CARBON - 1/2W 470-J
R-METAL-P - 3W 3.9K-J
R-METAL-P - 3W 4.7K-J
R-METAL-P - 3W 3.9K-J
R-METAL-P - 3W 4.7K-J
R-METAL - 3W 0.33-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 180K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 22K-J
R-CARBON - 1/4W 2.2K-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 82K-J
R-CARBON - 1/4W 47K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 47K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 22K-J
R-CARBON - 1/4W 390K-J
R-CARBON - 1/4W 100-J
R-METAL - 1/4W 9.1K-F
R-METAL - 1/4W 470-F
R-METAL - 1/4W 4.3K-F
R-METAL - 1/4W 12K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 220-J
R-METAL - 1/4W 62K-F
R-CARBON - 1/4W 470-J
R-CARBON - 1/2W 100-J
R-METAL - 1/4W 33K-F
R-METAL - 1/4W 24K-F
R-METAL - 1/4W 2.7K-F
R-METAL - 1/4W 680-F
R-METAL - 1/4W 3.3K-F
R-CARBON - 1/4W 10K-J
R-METAL - 1/4W 2.7K-F
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 330-J
R-CARBON - 1/4W 22K-J
R-CARBON - 1/4W 4.7K-J
R-CARBON - 1/4W 100-J
R-FUSE - 1/4W 47-J
R-METAL - 1/4W 8.2K-F
R-METAL - 1/4W 8.2K-F
R-CARBON - 1/4W 33-J
R-METAL - 1/4W 39K-F
R-CARBON - 1/2W 1.2K-J
R-CARBON - 1/4W 22K-J
R-METAL - 1/4W 68K-F
R-CARBON - 1/4W 180-J
R-METAL - 1/4W 100K-F
R-METAL - 1/4W 22K-F
Page 49
[#]
4-6
1-3
4-6
1-3
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
R5A94
R5A95
R5A96
R5A99
R5B01
R5B02
R5B03
R5B04
R5B05
R5B06
R5H01
R5H02
R5H03
R5H04
R5H07
R5H08
R5H09
R5H10
R5H11
R5H12
R5H13
R5H14
R5H15
R5H16
R5H17
R5H22
R5H23
R5H47
R5H48
R5H49
R5H50
R5H51
R5H58
R5H59
R5H60
R5H67
R5K01
R5K02
R5K03
R5K04
R5K05
R5K06
R5K07
R5K08
R5K09
R5K10
R5K11
R5K12
R5K20
R5K21
R5K21
R5K22
R5K23
R5K24
R5K25
R5K31
R5K32
R5K33
R5K34
R5K46
103C390070
103P714030
103P466080
103P714090
103P714030
103P714090
103P712060
103P711030
103P713070
103P713070
103P712050
103P758000
103P714030
103P463060
103P461060
103P711030
103P711010
103P710090
103P712020
103P712020
103P712020
103P710090
103P710090
103P710020
103P710020
103P711030
103P713010
103C392010
103P712060
103P714070
103P714070
103P712060
103P148000
103C191050
103C178080
103P148000
109D031070
103P412050
103P145000
103P144090
103P145000
103P144090
103P145000
103P144090
103P762020
103P711010
103P711090
103P760060
103P463060
103P464090
103P465000
103P145050
103P145050
103P145050
103P713040
103P711030
103P466020
103P465060
103P760060
103P712010
R-METAL-P - 3W 33-J
R-CARBON - 1/4W 33K-J
R-METAL - 1/4W 62K-F
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 33K-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 1K-J
R-FUSE - 1/4W 1-J
R-CARBON - 1/4W 33K-J
R-METAL - 1/4W 3K-F
R-METAL - 1/4W 430-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 68-J
R-CARBON - 1/4W 47-J
R-CARBON - 1/4W 560-J
R-CARBON - 1/4W 560-J
R-CARBON - 1/4W 560-J
R-CARBON - 1/4W 47-J
R-CARBON - 1/4W 47-J
R-CARBON - 1/4W 12-J
R-CARBON - 1/4W 12-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 3.3K-J
R-METAL-P - 3W 470-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 68K-J
R-CARBON - 1/4W 68K-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/2W 1-J
R-METAL - 3W 150-J
R-METAL - 1W 4.7-J
R-CARBON - 1/2W 1-J
R-COMP - 1/2W 10K-K
R-CARBON - 1/4W 1K-J
R-CARBON - 1/2W 120K-J
R-CARBON - 1/2W 100K-J
R-CARBON - 1/2W 120K-J
R-CARBON - 1/2W 100K-J
R-CARBON - 1/2W 120K-J
R-CARBON - 1/2W 100K-J
R-FUSE - 1/2W 560-J
R-CARBON - 1/4W 68-J
R-CARBON - 1/4W 330-J
R-FUSE - 1/2W 27-J
R-METAL - 1/4W 3K-F
R-METAL - 1/4W 10K-F
R-METAL - 1/4W 2.4K-F
R-CARBON - 1/2W 330K-J
R-CARBON - 1/2W 330K-J
R-CARBON - 1/2W 330K-J
R-CARBON - 1/4W 5.6K-J
R-CARBON - 1/4W 100-J
R-METAL - 1/4W 2.4K-F
R-METAL - 1/4W 20K-F
R-FUSE - 1/2W 27-J
R-CARBON - 1/4W 470-J
[#]
4-6
1-3
Ref #
Part #
Part Name & Description
R5K50
R5K51
R6B01
R6B02
R6B03
R6B04
R6B06
R6B07
R6B08
R6B09
R6B10
R6B11
R6B13
R6B15
R6B16
R6B17
R6B18
R6B19
R6B20
R6B21
R6B22
R6B23
R6B24
R6B25
R6B26
R6B27
R6B31
R6G01
R6G02
R6G03
R6G04
R6G06
R6G07
R6G08
R6G09
R6G10
R6G11
R6G13
R6G15
R6G16
R6G17
R6G20
R6G21
R6G22
R6G23
R6G31
R6R01
R6R02
R6R03
R6R04
R6R06
R6R07
R6R08
R6R09
R6R10
R6R11
R6R13
R6R15
R6R16
R6R17
103P762050
103P750010
103P711030
103P713090
103P464020
103P713000
103P462050
103P711030
103P710010
103P711030
103P713030
103C194020
103P331030
103P714090
103P411000
101P221030
103P713040
103P713050
101P221030
103P467030
103P467030
103P711030
103P713030
103P711030
103P413050
103P711030
103P712060
103P711030
103P713090
103P464020
103P463040
103P462030
103P711030
103P710010
103P711030
103P713030
103C194020
103P331030
103P714090
103P411000
101P221030
101P221030
103P467010
103P467010
103P711030
103P712060
103P711030
103P713090
103P464020
103P713000
103P462050
103P711030
103P710010
103P711030
103P713030
103C194020
103P331030
103P714090
103P411000
101P221030
R-FUSE - 1/2W 1K-J
R-FUSE - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 15K-J
R-METAL - 1/4W 2.4K-F
R-CARBON - 1/4W 2.7K-J
R-METAL - 1/4W 1K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 27K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 56-J
R-COMP - 1/2W 220-K
R-CARBON - 1/4W 5.6K-J
R-CARBON - 1/4W 6.8K-J
R-COMP - 1/2W 220-K
R-METAL - 1/4W 100K-F
R-METAL - 1/4W 100K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 6.8K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 15K-J
R-METAL - 1/4W 2.4K-F
R-METAL - 1/4W 2.4K-F
R-METAL - 1/4W 820-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 27K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 56-J
R-COMP - 1/2W 220-K
R-COMP - 1/2W 220-K
R-METAL - 1/4W 82K-F
R-METAL - 1/4W 82K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 15K-J
R-METAL - 1/4W 2.4K-F
R-CARBON - 1/4W 2.7K-J
R-METAL - 1/4W 1K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 27K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 56-J
R-COMP - 1/2W 220-K
Page 50
[#]
4-6
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
R6R20
R6R21
R6R22
R6R23
R6R31
R7B14
R7B15
R7B25
R7B26
R7K01
R7K02
R7K21
R7K22
R7K23
R7K24
R7K25
R7K26
R7K27
R7K28
R7K29
R7K30
R7K31
R7K32
R7K33
R7K34
R7K35
R7K36
R7L26
R7L27
R7L28
R7L29
R7L30
R7L31
R7L32
R8C02
R8C03
R8C05
R8C06
R8C07
R8C10
R8C11
R8C13
R8C14
R8C15
R8C18
R8C19
R8C21
R8C22
R8C23
R8C26
R8C27
R8C29
R8C30
R8C31
R8C34
R8C35
R8C37
R8C38
R8C39
R8C42
101P221030
103P467030
103P467030
103P711030
103P712060
109D151010
109D151010
109D151010
109D151010
103P712050
103P713010
103P710090
103P715030
103P712050
103P713080
103P712050
103P715030
103P713070
103P711050
103P712060
103P712050
103P715030
103P713030
103P712050
103P713000
103P711030
103P710090
103P462090
103P463030
103P463070
103P464030
103P465010
103P466010
103P466070
103P713010
103P711090
103C288070
103C288070
103C391050
103P713010
103P711090
103C288070
103C288070
103C391050
103P713010
103P711090
103C288070
103C288070
103C391050
103P713010
103P711090
103C288070
103C288070
103C391050
103P713010
103P711090
103C288070
103C288070
103C391050
103P713010
R-COMP - 1/2W 220-K
R-METAL - 1/4W 100K-F
R-METAL - 1/4W 100K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 47-J
R-CARBON - 1/4W 220K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 12K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 220K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 150-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 220K-J
R-CARBON - 1/4W 4.7K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 2.7K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 47-J
R-METAL - 1/4W 1.5K-F
R-METAL - 1/4W 2.2K-F
R-METAL - 1/4W 3.3K-F
R-METAL - 1/4W 5.6K-F
R-METAL - 1/4W 12K-F
R-METAL - 1/4W 33K-F
R-METAL - 1/4W 56K-F
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 330-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 330-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 330-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 330-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 330-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 3.3K-J
[#]
246
246
246
246
246
246
246
246
246
246
246
246
246
246
246
246
246
246
246
246
Ref #
Part #
Part Name & Description
R8C43
R8C45
R8C46
R8C47
R8C60
R8C61
R8C62
R8C63
R8C64
R8C65
R8C66
R8C67
R8P03
R8P03
R8P04
R8P05
R8P06
R9A02
R9A03
R9A05
R9A06
R9A09
R9A10
R9A11
R9A12
R9A20
R9A21
R9A22
R9A23
R9A24
R9A25
R9A26
R9A27
R9A28
R9A29
R9A30
R9A50
R9A51
R9A52
R9A53
R9A57
R9A58
R9A59
R9A60
R9A61
R9A63
R9A64
R9A65
R9A66
R9A67
R9A68
R9A70
R9A71
R9A72
R9A73
R9A74
R9A76
R9A77
R9A80
R9A81
103P711090
103C288070
103C288070
103C391050
103C191090
103C191090
103P713010
103P713010
103P713010
103P713010
103P713010
103P713010
103P712010
103P712050
103P711070
103P711070
103P711070
102P084000
109C010010
109C010010
109C010010
103P145030
103P713090
103P145030
103P713060
103C391020
103P712050
103P713000
103P710090
103P142070
103P462050
103P462050
103P712050
103P713070
103P711030
103P710080
103P712090
103P714010
103C183070
103P712030
103P712070
103P145030
103P710010
103P710090
103P713040
103P712090
103P713030
103P465090
103P714010
103P710050
103C390020
109D151090
103P145030
103P462050
103P464020
103P465080
103P715070
103P713030
103C193060
103P142090
R-CARBON - 1/4W 330-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL - 3W 330-J
R-METAL - 3W 330-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 470-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 220-J
R-CARBON - 1/4W 220-J
R-CARBON - 1/4W 220-J
R-CEMENT-WIRE - 15W 2.2-K
R-COMP - 1/2W 1M-K
R-COMP - 1/2W 1M-K
R-COMP - 1/2W 1M-K
R-CARBON - 1/2W 220K-J
R-CARBON - 1/4W 15K-J
R-CARBON - 1/2W 220K-J
R-CARBON - 1/4W 8.2K-J
R-METAL-P - 3W 82-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 2.7K-J
R-CARBON - 1/4W 47-J
R-CARBON - 1/2W 1.5K-J
R-METAL - 1/4W 1K-F
R-METAL - 1/4W 1K-F
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 39-J
R-CARBON - 1/4W 2.2K-J
R-CARBON - 1/4W 22K-J
R-METAL - 2W 10K-J
R-CARBON - 1/4W 680-J
R-CARBON - 1/4W 1.5K-J
R-CARBON - 1/2W 220K-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 47-J
R-CARBON - 1/4W 5.6K-J
R-CARBON - 1/4W 2.2K-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 1/4W 27K-F
R-CARBON - 1/4W 22K-J
R-CARBON - 1/4W 22-J
R-METAL-P - 3W 12-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/2W 220K-J
R-METAL - 1/4W 1K-F
R-METAL - 1/4W 2.4K-F
R-METAL - 1/4W 24K-F
R-CARBON - 1/4W 470K-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 8.2K-J
R-CARBON - 1/2W 2.2K-J
Page 51
[#]
4-6
1-3
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
R9A82
R9A83
R9A84
R9B01
R9B02
R9B03
R9B09
R9D00
103P465050
103P464010
103P713070
103P711030
103P713080
103P714050
109D151030
109D036020
R-METAL - 1/4W 18K-F
R-METAL - 1/4W 4.7K-F
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 12K-J
R-CARBON - 1/4W 47K-J
R-CARBON - 1/4W 4.7-J
R-COMP - 1/2W 4.7M-K
[#]
CAPACITORS & TRIMMERS
Value
SL50V 2P-C
Value
50V 3P-C
CH50V 10P-C
SL50V 10P-J
CH50V 12P-J
CH50V 15P-J
CH50V 22P-J
CH50V 33P-J
CH50V 47P-J
CH50V 56P-J
SL50V 56P-J
CH50V 82P-J
CH50V 100P-J
CH50V 120P-J
CH50V 150P-J
CH50V 220P-J
B50V 220P-K
CH50V 270P-J
B50V 470P-K
CH25V 560P-J
CH25V 820P-J
B50V 1000P-K
CH25V 1000P-J
B50V 1500P-K
Ref #
C1A13
C1A21
C1A24
C1A26
C1B13
C1B21
C1B24
C1B26
C2AGC
C2AGD
C2AJB
C2AJD
C2AKC
C2AKD
C2ANC
C2AND
C2APC
C2APD
C2ARC
C2ARD
CHIP Type Capacitors (Listed by Value)
Part No.
Value
154P350040
B50V 2200P-K
Part No.
Value
154P340040
B50V 4700P-K
154P341010
B50V 0.01M-K
154P351020
F50V 0.01M-Z
154P341030
B50V 0.015M-K
154P341050
B25V 0.047M-K
154P341090
B25V 0.068M-K
154P342030
B16V 0.082M-K
154P342070
B16V 0.1M-K
154P342090
F25V 0.1M-Z
154P353000
F50V 0.1M-Z
154P343030
B10V 0.22M-K
154P343050
B25V 0.33M-K
154P343070
B10V 0.47M-K
154P343090
B16V 0.47M-K
154P344030
B10V/6.3V 1M-K
141P140010
F16V 1M-Z
154P344050
50V 1M-M
141P140050
50V 2.2M-M
154P345030
6.3V 47M-M
154P345070
16V 10M-M
141P140090
6.3V 47M-M
154P345090
6V 47M-M
141P141010
6.3V 100M-M
Conventional Capacitors (By Ref #)
Part #
Part Name & Description
181P352040 C-ELEC - 16V 100M-M
181P352040 C-ELEC - 16V 100M-M
181P352040 C-ELEC - 16V 100M-M
172P262010 C-M-POLY - 50V 0.047M-J
181P355090 C-ELEC - 50V 100M-M
181P352040 C-ELEC - 16V 100M-M
181P352040 C-ELEC - 16V 100M-M
172P262010 C-M-POLY - 50V 0.047M-J
155P239040 C-CER - CH50V 100P-J
142P024060 C-CER - BF50V 0.1M-Z
142P024060 C-CER - BF50V 0.1M-Z
155P239040 C-CER - CH50V 100P-J
181P352040 C-ELEC - 16V 100M-M
155P239040 C-CER - CH50V 100P-J
142P024060 C-CER - BF50V 0.1M-Z
155P239040 C-CER - CH50V 100P-J
181P352040 C-ELEC - 16V 100M-M
155P239040 C-CER - CH50V 100P-J
142P024060 C-CER - BF50V 0.1M-Z
155P239040 C-CER - CH50V 100P-J
Part No.
141P141030
Part No.
141P141070
141P142010
141P143080
141P142030
141P142090
141P143010
141P143020
141P143030
141P144020
141P134090
141P146040
141P138080
141P146080
141P139090
141P147020
141P144060
181P526010
181P526020
181P530030
181P532030
181P520030
181P522060
181P520040
Ref #
Part #
Part Name & Description
C2ATC
C2ATD
C2AYC
C2AYD
C2AZC
C2AZE
C2AZF
C2K01
C2K03
C2K08
C2K10
C2K15
C2K17
C2K18
C2K22
C2K27
C2K43
C2K48
C2K50
C2K63
C2K71
C2K75
C2L29
C2L52
C2M28
C2M29
C2M31
C2M34
C2M36
C2M38
C2M43
C2M44
C2M54
C2M64
C2M80
C2M88
C2M89
C2M98
C2MA4
C2MA6
C2MA9
C2MC4
C2MC8
C2MD6
C2MD7
C2N03
C2N27
C2NA6
C2NC5
C2P01
C2P26
C2P32
C2P42
C2R29
C2V14
C2V17
C2V19
C2V29
C2V30
C2V32
142P024060
155P239040
142P024060
155P239040
142P024060
181P355050
155P239040
181P355050
181P355050
181P355050
181P355050
181P355050
181P355050
181P351060
181P355050
181P355050
181P352030
181P352030
181P355050
181P355050
181P352030
181P352030
181P352030
181P352030
181P351080
181P351080
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P355050
181P352030
181P352030
181P355010
181P352030
181P355050
181P352030
181P352030
181P352030
181P352030
181P352040
181P352040
181P352040
181P352070
181P350060
181P355050
181P355050
181P352070
181P350060
181P352030
181P352030
181P352030
181P352040
181P355040
181P352040
181P352040
181P118010
181P355000
C-CER - BF50V 0.1M-Z
C-CER - CH50V 100P-J
C-CER - BF50V 0.1M-Z
C-CER - CH50V 100P-J
C-CER - BF50V 0.1M-Z
C-ELEC - 50V 10M-M
C-CER - CH50V 100P-J
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 10V 330M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 10V 1000M-M
C-ELEC - 10V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 1M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 470M-M
C-ELEC - 3V 1000M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 470M-M
C-ELEC - 3V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 4.7M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 0.68M-M
C-ELEC - 50V 0.47M-M
Page 52
[#]
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
C2V48
C2V49
C2V55
C2V57
C2V61
C2W02
C2W05
C2W09
C2W14
C3A14
C3A20
C3A21
C3A28
C3A29
C3A32
C3A33
C3A34
C3A46
C3A49
C3E01
C3E02
C3E03
C3E04
C3E05
C3E06
C3E07
C3E08
C3E09
C3E11
C3E12
C3E14
C3J01
C3J05
C3J06
C3J09
C3J10
C3J24
C3K02
C3K04
C3K09
C3K11
C3K16
C3K18
C3K23
C3K25
C3K29
C3K31
C3K62
C3K64
C4B01
C4B02
C4B03
C4B04
C4B06
C4B08
C4B09
C4B10
C4B11
C5A01
C5A02
172P166030
172P166030
181P352040
181P355060
181P352040
181P352080
181P352030
181P352030
181P352030
181P355050
181P355050
181P355050
181P355050
181P355050
181P355050
181P355050
181P355030
181P355050
181P355050
181P354050
181P355010
172P331010
181P355010
172P331010
181P355050
181P353090
141P197080
172P262050
172P262050
172P262050
172P262050
181P352030
181P355050
181P122070
181P355050
181P122070
181P352030
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
181P355010
172P261030
181P358000
172P383030
181P184020
172P330090
172P263070
181P355060
181P354050
181P353090
181P354050
181P355050
C-TF - 50V 0.1M-J
C-TF - 50V 0.1M-J
C-ELEC - 16V 100M-M
C-ELEC - 50V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 3.3M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 35V 47M-M
C-ELEC - 50V 1M-M
C-POLY - 50V 6800P-J
C-ELEC - 50V 1M-M
C-POLY - 50V 6800P-J
C-ELEC - 50V 10M-M
C-ELEC - 5V 2200M-M
C-CER - F50V 0.1M-Z
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 25V 10M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 25V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-ELEC - 50V 1M-M
C-M-POLY - 50V 0.01M-J
C-ELEC - 35V 1000M-M
C-M-POLY - 100V 0.47M-K
C-ELEC - 35V 100M-M
C-POLY - 50V 4700P-J
C-M-POLY - 50V 1.0M-J
C-ELEC - 50V 22M-M
C-ELEC - 35V 47M-M
C-ELEC - 5V 2200M-M
C-ELEC - 35V 47M-M
C-ELEC - 50V 10M-M
[#]
Ref #
Part #
Part Name & Description
C5A03
C5A04
C5A05
C5A10
C5A12
C5A17
C5A18
C5A21
C5A22
C5A23
C5A31
C5A31
C5A32
C5A32
C5A34
C5A35
C5A36
C5A37
C5A39
C5A40
C5A41
C5A42
C5A43
C5A45
C5A50
C5A51
C5A52
C5A55
C5A56
C5A57
C5A58
C5A59
C5A60
C5A61
C5A62
C5A63
C5A64
C5A65
C5A66
C5A67
C5A68
C5A69
C5A70
C5A71
C5A72
C5H01
C5H02
C5H03
C5H04
C5H07
C5H16
C5H17
C5H19
C5H20
C5H21
C5H24
C5K00
C5K01
C5K02
C5K03
142P020090
172P263010
172P262010
181P191000
181P354090
142P020090
142P020090
172P262050
181P355050
181P355050
172P571030
172P571040
172P571030
172P571040
154P262050
142P012010
172P524010
172P436070
142P011030
142P011000
181P352080
181P352030
181P190050
181P352070
142P024060
154P260010
172P580090
172P088060
181P352030
172P262070
142P024060
142P023080
172P262050
181P355040
142P023080
142P023080
181P352010
181P355050
142P024060
142P023080
181P123070
142P024060
172P264010
172P262060
181P355010
181P354080
142P023080
142P023080
155P238090
142P023080
172P186030
172P261030
181P183010
181P352040
181P780060
181P192060
172P572090
172P572090
181P198040
142P020050
C-CER - B50V 1000P-K
C-M-POLY - 50V 0.33M-J
C-M-POLY - 50V 0.047M-J
C-ELEC - 160V 22M-M/Q
C-ELEC - 35V 470M-M
C-CER - B50V 1000P-K
C-CER - B50V 1000P-K
C-M-POLY - 50V 0.1M-J
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-M-PLA-PP - 1500V 3300P-J
C-M-PLA-PP - 1500VHP 3600P-J
C-M-PLA-PP - 1500V 3300P-J
C-M-PLA-PP - 1500VHP 3600P-J
C-CER - R2KV 560P-K
C-CER - B500V 4700P-K
C-M-POLY - 250V 2.2M-J
C-M-PLA-PP - 250V 0.56M-J
C-CER - B500V 1000P-K
C-CER - B500V 560P-K
C-ELEC - 16V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 160V 1M-M/Q
C-ELEC - 16V 470M-M
C-CER - BF50V 0.1M-Z
C-CER - R1KV 220P-K
C-M-PLA-PP - 1800V 2200P-J
C-PLA-PP - 630V 6800P-J
C-ELEC - 16V 47M-M
C-M-POLY - 50V 0.15M-J
C-CER - BF50V 0.1M-Z
C-CER - BF50V 0.01M-Z
C-M-POLY - 50V 0.1M-J
C-ELEC - 50V 4.7M-M
C-CER - BF50V 0.01M-Z
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 22M-M
C-ELEC - 50V 10M-M
C-CER - BF50V 0.1M-Z
C-CER - BF50V 0.01M-Z
C-ELEC-NP - 50V 0.47M-M
C-CER - BF50V 0.1M-Z
C-M-POLY - 50V 2.2M-J
C-M-POLY - 50V 0.12M-J
C-ELEC - 50V 1M-M
C-ELEC - 35V 330M-M
C-CER - BF50V 0.01M-Z
C-CER - BF50V 0.01M-Z
C-CER - CH50V 270P-J
C-CER - BF50V 0.01M-Z
C-PLA-PP - 200V 0.01M-K
C-M-POLY - 50V 0.01M-J
C-ELEC - 25V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 160V 10M-M
C-ELEC - 200V 22M-M/Q
C-M-PLA-PP - 1500V 0.015M-J
C-M-PLA-PP - 1500V 0.015M-J
C-ELEC - 450V 4.7M-M/Q
C-CER - B50V 470P-K
Page 53
[#]
1-3
4-6
1-3
4-6
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
C5K05
C5K12
C5K14
C5K15
C5K15
C5K16
C5K17
C6B01
C6B02
C6B03
C6B04
C6B05
C6B06
C6B07
C6B08
C6B09
C6B10
C6B12
C6B13
C6B14
C6B15
C6G01
C6G02
C6G03
C6G04
C6G05
C6G06
C6G07
C6G09
C6G10
C6G12
C6G13
C6G14
C6G15
C6R01
C6R02
C6R03
C6R04
C6R05
C6R06
C6R07
C6R09
C6R10
C6R12
C6R13
C6R14
C6R15
C7A00
C7A16
C7A99
C7ACB
C7B02
C7B11
C7B21
C7B88
C7B96
C7BMA
C7D00
C7D97
C7K01
181P354050
181P352040
181P354050
181P191000
181P194000
172P331010
172P434010
154P400010
181P195050
155P231070
142P023080
181P352030
142P023080
172P532050
142P020030
142P023080
172P532050
155P231050
155P231090
154P405000
154P405000
154P400010
181P195050
155P231090
142P023080
181P352030
142P023080
172P532050
142P023080
172P532050
155P231050
155P231090
154P405000
154P405000
154P400010
181P195050
155P231070
142P023080
181P352030
142P023080
172P532050
142P023080
172P532050
155P231050
155P231090
154P405000
154P405000
154P345090
181P352030
181P352030
181P355050
181P355010
181P352050
181P352050
181P355050
181P355010
181P352030
181P352040
181P352040
181P352030
C-ELEC - 35V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 35V 47M-M
C-ELEC - 160V 22M-M/Q
C-ELEC - 250V 10M-M/Q
C-POLY - 50V 6800P-J
C-M-PLA-PP - 250V 0.047M-J
C-CER - B1KV 220P-K
C-ELEC - 350V 10M-M/Q
C-CER - CH50V 18P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 47M-M
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - B50V 330P-K
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - CH50V 15P-J
C-CER - CH50V 22P-J
C-CER - B3KV 1000P-K
C-CER - B3KV 1000P-K
C-CER - B1KV 220P-K
C-ELEC - 350V 10M-M/Q
C-CER - CH50V 22P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 47M-M
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - CH50V 15P-J
C-CER - CH50V 22P-J
C-CER - B3KV 1000P-K
C-CER - B3KV 1000P-K
C-CER - B1KV 220P-K
C-ELEC - 350V 10M-M/Q
C-CER - CH50V 18P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 47M-M
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - CH50V 15P-J
C-CER - CH50V 22P-J
C-CER - B3KV 1000P-K
C-CER - B3KV 1000P-K
C-CER-CHIP - CH25V 1000P-J
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 1M-M
C-ELEC - 16V 220M-M
C-ELEC - 16V 220M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 1M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 47M-M
[#]
1-3
4-6
4-6
246
246
Ref #
Part #
Part Name & Description
C7K20
C7K21
C7K23
C7K25
C7K26
C7K27
C7K28
C7K30
C7P20
C7RF2
C7S03
C8C03
C8C04
C8C05
C8C06
C8C09
C8C11
C8C14
C8C18
C8C19
C8C20
C8C21
C8C23
C8C26
C8C29
C8C43
C8C44
C8C45
C8C46
C8C47
C8C48
C8D16
C8D19
C8D20
C8D21
C8D22
C8D29
C8D30
C8D31
C8D33
C8D39
C8D40
C8E01
C8E03
C8E05
C8E07
C8E09
C8E12
C8E14
C8E16
C8G00
C8G03
C8G05
C8G06
C9A05
C9A06
C9A07
C9A08
C9A09
C9A10
155P314040
181P355050
181P355010
172P262050
172P262050
181P355010
181P352040
172P261030
181P352030
181P355050
181P352030
181P358000
142P024060
181P358000
142P024060
155P233090
155P233090
155P233090
181P358000
142P024060
181P358000
142P024060
155P233090
155P233090
155P233090
142P020080
142P020080
142P020080
142P020080
142P020080
142P020080
181P352030
181P352030
181P352030
181P352030
181P352030
181P355010
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352020
181P352030
181P352030
189P185070
189P185070
189P153040
189P185090
189P185090
189P185090
C-CER - SL50V 220P-J
C-ELEC - 50V 10M-M
C-ELEC - 50V 1M-M
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-ELEC - 50V 1M-M
C-ELEC - 16V 100M-M
C-M-POLY - 50V 0.01M-J
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 35V 1000M-M
C-CER - BF50V 0.1M-Z
C-ELEC - 35V 1000M-M
C-CER - BF50V 0.1M-Z
C-CER - CH50V 150P-J
C-CER - CH50V 150P-J
C-CER - CH50V 150P-J
C-ELEC - 35V 1000M-M
C-CER - BF50V 0.1M-Z
C-ELEC - 35V 1000M-M
C-CER - BF50V 0.1M-Z
C-CER - CH50V 150P-J
C-CER - CH50V 150P-J
C-CER - CH50V 150P-J
C-CER - B50V 820P-K
C-CER - B50V 820P-K
C-CER - B50V 820P-K
C-CER - B50V 820P-K
C-CER - B50V 820P-K
C-CER - B50V 820P-K
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 1M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 33M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-CER - AC250V E1000P-M
C-CER - AC250V E1000P-M
C-M-POLY - 250VAC 0.1M-M
C-CER - AC250V E2200P-M
C-CER - AC250V E2200P-M
C-CER - AC250V E2200P-M
Page 54
[#]
246
246
246
246
246
246
246
246
246
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
C9A11
C9A13
C9A14
C9A15
C9A16
C9A17
C9A20
C9A22
C9A25
C9A27
C9A28
C9A29
C9A30
C9A31
C9A32
C9A33
C9A34
C9A39
C9A50
C9A51
C9A52
C9A53
C9A54
C9A55
C9A56
C9A57
C9A59
C9A60
C9A61
C9A62
C9A63
C9A64
C9A65
C9A66
C9A68
C9A69
C9A70
C9A71
C9A72
C9A73
C9A74
C9A75
C9A76
C9A77
C9A78
C9A79
C9A80
C9A82
C9A83
C9A84
C9A85
C9A86
C9A87
C9AAB
C9ABA
C9B01
C9B06
C9B07
C9B08
C9B08
189P185090
189P152070
189P152070
181P355010
189P185070
189P185070
142P024060
181P199080
172P262050
154P270050
172P262050
142P010090
142P010090
181P743040
181P352040
181P354060
181P354060
181P355010
142P020050
181P355090
154P260080
185D122040
154P260080
172P339070
181P355080
142P010090
185D122040
154P400030
142P010090
189D183010
185D120040
181P190090
181P194000
142P012050
142P010090
181P736070
181P736070
181P736070
181P736070
181P736070
142P010090
181P355080
142P023080
142P020090
142P020090
181P736070
181P746040
142P024060
181P355050
181P352040
181P735010
181P735010
181P735010
181P351070
181P352040
142P023080
181P746050
142P020090
181P743040
181P743070
C-CER - AC250V E2200P-M
C-M-POLY - 250VAC 0.01M-M
C-M-POLY - 250VAC 0.01M-M
C-ELEC - 50V 1M-M
C-CER - AC250V E1000P-M
C-CER - AC250V E1000P-M
C-CER - BF50V 0.1M-Z
C-ELEC - 200V 47M-M/Q
C-M-POLY - 50V 0.1M-J
C-CER - SL1KV 22P-J
C-M-POLY - 50V 0.1M-J
C-CER - B500V 470P-K
C-CER - B500V 470P-K
C-ELEC - 16V 330M-M
C-ELEC - 16V 100M-M
C-ELEC - 35V 100M-M
C-ELEC - 35V 100M-M
C-ELEC - 50V 1M-M
C-CER - B50V 470P-K
C-ELEC - 50V 100M-M
C-CER - R1KV 3300P-K
C-ELEC - H200V 820M-M
C-CER - R1KV 3300P-K
C-POLY - 50V 560P-J
C-ELEC - 50V 47M-M
C-CER - B500V 470P-K
C-ELEC - H200V 820M-M
C-CER - B1KV 470P-K
C-CER - B500V 470P-K
C-ELEC - 400V 100M-KC
C-ELEC - 160V 820M-M
C-ELEC - 160V 10M-M/Q
C-ELEC - 250V 10M-M/Q
C-CER - B500V 0.01M-K
C-CER - B500V 470P-K
C-ELEC - 35V 330M-M
C-ELEC - 35V 330M-M
C-ELEC - 35V 330M-M
C-ELEC - 35V 330M-M
C-ELEC - 35V 330M-M
C-CER - B500V 470P-K
C-ELEC - 50V 47M-M
C-CER - BF50V 0.01M-Z
C-CER - B50V 1000P-K
C-CER - B50V 1000P-K
C-ELEC - 35V 330M-M
C-ELEC - 35V 150M-M
C-CER - BF50V 0.1M-Z
C-ELEC - 50V 10M-M
C-ELEC - 16V 100M-M
C-ELEC - 25V 470M-M
C-ELEC - 25V 470M-M
C-ELEC - 25V 470M-M
C-ELEC - 10V 470M-M
C-ELEC - 16V 100M-M
C-CER - BF50V 0.01M-Z
C-ELEC - 35V 220M-M
C-CER - B50V 1000P-K
C-ELEC - 16V 330M-M
C-ELEC - 16V 1000M-M
[#]
Ref #
Part #
Part Name & Description
[#]
C9B10 181P352040
C9B11 181P352080
C9C01 181P352030
C9C02 181P352030
C9C11 181P352030
C9C12 181P352030
C9C21 181P352030
C9C22 181P352040
C9C35 181P355050
C9C38 181P355050
C9C41 181P352030
C9C42 181P352030
C9C51 181P746040
C9C54 181P743040
C9C55 181P352070
C9C61 181P352030
C9C62 181P352040
C9D00 189P153040
C9D01 189P153040
CF2N10 299P267010
CF2P10 299P267010
CF2V01 299P259010
C-ELEC - 16V 100M-M
C-ELEC - 16V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
1-3
C-ELEC - 16V 47M-M
4-6
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 35V 150M-M
C-ELEC - 16V 330M-M
C-ELEC - 16V 470M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-M-POLY - 250VAC 0.1M-M
C-M-POLY - 250VAC 0.1M-M
RESONATOR-CERAMIC - CSBLA503KECZF30-B0
RESONATOR-CERAMIC - CSBLA503KECZF30-B0
OSC-CERAMIC - CSALA2M69G4ZF01-B0 2.69MHZ
S7L21
S7L22
S7L23
S7L24
S7L25
S7L26
S7L27
S7L28
S7L29
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
SW-KEY
SW-KEY
SW-KEY
SW-KEY
SW-KEY
SW-KEY
SW-KEY
SW-KEY
SW-KEY
096Z465030
246C351030
305P702020
330P293010
330P293020
338P054010
338P054020
411D044020
411D062010
449C141030
453B036010
453B036020
480P053010
480P063010
490P154010
490P154020
490P174010
490P174020
490P174030
490P174070
490P174080
490P174090
490P220010
490P220040
TAPE-ADHESIVE
3456
CORD-AC - POWER
SW-RF - YAA41-0126G
YOKE-DEFL - 625UH
456
YOKE-DEFL - 760UH
123
SVM-ASSY
135
SVM-ASSY
246
CORE-FERRITE - TDK 32mm(L) @ 19.5mm(Dia.)
CORE-FERRITE - TDK-18mm(L) @ 15mm(Dia.)
SOCKET-CRT
CAP-ANODE - LONG [R]
CAP-ANODE - LONG [GB]
SPEAKER - 5 INCH
1&2
SPEAKER - 6 INCH
3456
LENS-BARREL - RED
1&2
LENS-BARREL - BLUE/GREEN
1&2
LENS-BARREL - RED
4
LENS-BARREL - GREEN
4
LENS-BARREL - BLUE
4
LENS - RED
5&6
LENS - GREEN
5&6
LENS - BLUE
5&6
LENS-BARREL - RED/BLUE
3
LENS-BARREL - GREEN
3
SWITCHES
BOARD
BOARD
BOARD
BOARD
BOARD
BOARD
BOARD
BOARD
BOARD
-
KSHS611BT
KSHS611BT
KSHS611BT
KSHS611BT
KSHS611BT
KSHS611BT
KSHS611BT
KSHS611BT
KSHS611BT
MISCELLANEOUS
Page 55
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
589C063010
597D843010
598D417010
598D456010
622B009020
622C086010
622D967010
642C340010
642C352010
702A431010
767D048090
767D072030
767D072040
767D072050
AG5K00 224D019040
AG6B01 224D019090
AG6B02 224D019090
AG6G01 224D019090
AG6G02 224D019090
AG6R01 224D019090
AG6R02 224D019090
F5A00 283P144070
F9A02 283P144090
F9A03 283P144080
F9A04 283P144090
F9A05 283P144080
F9B01 283P144070
F9D00 283D131040
F9D01 283P144060
J2AAA 452C385010
J7CAA 452C383010
K9A50 287P111010
K9A51 287P111010
PC9A21 268P058020
PC9A50 268P106020
PJ2J00 440C407010
PJ2J01 440C410010
PJ2J02 440C410010
PJ2J03 440C410010
PJ2J04 440C409010
PJ2J05 440C408010
PJ2J06 440C421010
PJ2J11 440C412010
PJ7B11 451C129010
PJ7B12 451C129010
PJ7B21 451C129010
PJ7B22 451C129010
TU1A01 295P516010
TU1B01 295P516020
X2M47 285P426040
X2N21 285P426010
X2P21 285P426010
X3A01 285P413010
X7A13 285P434020
X7J10 285P335050
X7P09 285P434010
Z7K01 939P617010
Part Name & Description
CASTER - DUAL WHEEL
STIFFENER-MIRROR - 3/4"X3/4" TUBING
PLATE-RF SWITCH
BRACKET-MIRROR - TOP
TRAY-CRT
CLIP-MIRROR - TOP
BAND-KM
BOARD-MIRROR - TOP
CLIP-MIRROR - TOP
BOARD-TERMINAL
MIRROR - 65"
MIRROR - 55"
MIRROR - 48"
MIRROR - 55"
AIR GAP - 2.0+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
FUSE - 125V 3A (20N 3000)
FUSE - 125V 10A (20N 10K)
FUSE - 125V 5A (20N 5000)
FUSE - 125V 10A (20N 10K)
FUSE - 125V 5A (20N 5000)
FUSE - 125V 3A (20N 3000)
FUSE - S10A 125A
FUSE - 125V 7A (20N 7000)
CONNECTOR-DVI
CONNECTOR-DSUB
RELAY-POWER - LKS1AF-5V
RELAY-POWER - LKS1AF-5V
PHOTO-COUPLER - ON3131-R/ON3161-R
PHOTO-COUPLER - CNZ3132
PIN-JACK-BOARD-6P
PIN-JACK-BOARD-5P
PIN-JACK-BOARD-5P
PIN-JACK-BOARD-5P
PIN-JACK-BOARD-2P
PIN-JACK-BOARD-3P
PIN-JACK-BOARD-2P
PIN-JACK-BOARD-3P
JACK-MINI - AV NET/IR BLAST
JACK-MINI - AV NET/IR BLAST
JACK-MINI - AV NET/IR BLAST
JACK-MINI - AV NET/IR BLAST
TUNER-TV - 115-V-F045AP
TUNER-TV - 115-V-F025AP
QUARTZ-CRYST - 20.000MHZ
QUARTZ-CRYST - 3.579545MHZ
QUARTZ-CRYST - 3.579545MHZ
QUARTZ-CRYST - 18.432MHZ
QUARTZ-CRYST - 16.000MHZ
QUARTZ-CRYST - 80.000MHZ
QUARTZ-CRYST - 8.000MHZ
UNIT-PREAMP - GP1U283Q
[#]
Ref #
Part #
Part Name & Description
[#]
PRINTED CIRCUIT BOARDS
5&6
930B899001 ASSY-PWB-MAIN
930B899003 ASSY-PWB-MAIN
930B900001 ASSY-PWB-POWER
930B901001-48 ASSY-PWB-SIGNAL
930B901001-55 ASSY-PWB-SIGNAL
930B901001-65 ASSY-PWB-SIGNAL
930B901002-48 ASSY-PWB-SIGNAL
930B901002-55 ASSY-PWB-SIGNAL
930B901002-65 ASSY-PWB-SIGNAL
930B902001 ASSY-PWB-TERMINAL
934C062001 ASSY-PWB-CRT
934C063001 ASSY-PWB-DOUBLER
935D738001 ASSY-PWB-PREAMP
935D738002 ASSY-PWB-PREAMP
935D739001 ASSY-PWB-FRONT
935D740001 ASSY-PWB-CONTROL
1&2
3&4
5&6
3&4
5&6
4
1&2
3
456
123
1
3
5
2
4
6
135
246
COSMETIC PARTS
705C011020
761A209010
761A210010
761A211010
761A212010
761A213010
761A215010
850A003010
850A003020
DOOR-FRONT - A/V IN COVER
GRILLE-SP
GRILLE-SP
GRILLE-SP
GRILLE-SP
GRILLE-SP
GRILLE-SP
INLAY-TERMINAL
INLAY-TERMINAL
242D527010
290P116010
290P117010
853B399010
I/B WS48313
I/B WS48413
I/B WS55313
I/B WS55413
I/B WS65313
I/B WS65413
I/QR WS48313
I/QR WS48413
I/QR WS55313
I/QR WS55413
I/QR WS65313
I/QR WS65413
CABLE-IR
REMOTE CONTROL - V22
REMOTE CONTROL - V22+
CARD-REGISTRATION
IB - OWNERS GUIDE
IB - OWNERS GUIDE
IB - OWNERS GUIDE
IB - OWNERS GUIDE
IB - OWNERS GUIDE
IB - OWNERS GUIDE
QR-GUIDE
QR-GUIDE
QR-GUIDE
QR-GUIDE
QR-GUIDE
QR-GUIDE
2
4
6
3
5
1
135
246
ACCESSORIES
246
Page 56
246
135
246
1
2
3
4
5
6
1
2
3
4
5
6
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
Ref #
Part #
Part Name & Description
SCREEN ASSEMBLY PARTS
WS-48313 Screen Parts (Figure 1)
(1)
491P138020 SCREEN-LENTICULAR - 48"
(2)
491P139020 LENS-FRESNEL - 48"
(3)
597C027010 BRACKET-SCREEN FRAME
(4)
598D339010 BRACKET-SCREEN-SIDE
(5)
622B010010 HOLDER-SCREEN - TOP
(6)
622B011010 HOLDER-SCREEN - BOTTOM
(7)
622B012010 HOLDER-SCREEN - SIDE
(8)
622B013020 CLIP-DIAMOND SHIELD
(9)
635B109010 STIFFENER-SCREEN - TOP
(10)
751A005060 BEZEL-FRONT
(11)
760D628090 DIAMOND SHIELD
WS-48413 Screen Parts (Figure 2)
(1)
491P138020 SCREEN-LENTICULAR - 48"
(2)
491P139020 LENS-FRESNEL - 48"
(3)
597C027010 BRACKET-SCREEN FRAME
(4)
598D339010 BRACKET-SCREEN-SIDE
(5)
622B010010 HOLDER-SCREEN - TOP
(6)
622B011010 HOLDER-SCREEN - BOTTOM
(7)
622B012010 HOLDER-SCREEN - SIDE
(8)
622B013020 CLIP-DIAMOND SHIELD
(9)
635B109010 STIFFENER-SCREEN - TOP
(10)
751A005030 BEZEL-FRONT
(11)
760D628090 DIAMOND SHIELD
Figure 1: WS-48313 / WS-48413
Screen Assembly Parts (Rear View)
Page 57
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
WS-55313 Screen Parts (Figure2)
(1)
491P103030 SCREEN-LENTICULAR - 55"
(2)
491P104030 LENS-FRESNEL - 55"
(3)
622B016010 CLIP-DIAMOND SHIELD
(4)
622C104010 HOLDER-SCREEN
(5)
701B481010 FRAME-SCREEN-TOP
(6)
701B482010 FRAME-SCREEN-SIDE
(7)
702A435010 CAP-CORNER
(8)
702A436010 PANEL-CONTROL
(9)
760D628080 DIAMOND SHIELD
Ref #
Part #
Part Name & Description
WS-55413 Screen Parts (Figure 2)
(1)
491P103030 SCREEN-LENTICULAR - 55"
(2)
491P104030 LENS-FRESNEL - 55"
(3)
622B016010 CLIP-DIAMOND SHIELD
(4)
622C104010 HOLDER-SCREEN
(5)
701B481010 FRAME-SCREEN-TOP
(6)
701B482010 FRAME-SCREEN-SIDE
(7)
702A435010 CAP-CORNER
(8)
702A436020 PANEL-CONTROL
(9)
760D628080 DIAMOND SHIELD
Figure 2: WS-55313 / WS-55413 / WS-65313 / WS-65413
Screen Assembly Parts (Rear View)
Page 58
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
[#] Model Legend: (1) WS-48313, (2) WS-48413, (3) WS-55313, (4) WS-55413, (5) WS-65313, (6) WS-65413
Ref #
Part #
Part Name & Description
WS-65313 Screen Parts (Figure2)
(1)
491P105050 SCREEN-LENTICULAR - 65"
(2)
491P106080 LENS-FRESNEL - 65"
(3)
622B016020 CLIP-DIAMOND SHIELD
(4)
622C104020 HOLDER-SCREEN
(5)
701B481020 FRAME-SCREEN-TOP
(6)
701B482020 FRAME-SCREEN-SIDE
(7)
702A435010 CAP-CORNER
(8)
702A437010 PANEL-CONTROL
(9)
760D627070 DIAMOND SHIELD
(10)
594C988010 BRACKET-SCREEN FRAME
Ref #
Part #
Part Name & Description
WS-65413 Screen Parts (Figure 2)
(1)
491P105050 SCREEN-LENTICULAR - 65"
(2)
491P106080 LENS-FRESNEL - 65"
(3)
622B016020 CLIP-DIAMOND SHIELD
(4)
622C104020 HOLDER-SCREEN
(5)
701B481020 FRAME-SCREEN-TOP
(6)
701B482020 FRAME-SCREEN-SIDE
(7)
702A435010 CAP-CORNER
(8)
702A437020 PANEL-CONTROL
(9)
760D627070 DIAMOND SHIELD
(10)
594C988010 BRACKET-SCREEN FRAME
Page 59
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
POWER SUPPLY
Page 60
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
VIDEO/COLOR PATH
Page 61
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SYNC PATH
Page 62
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
DEFLECTION / HV CIRCUIT
Page 63
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
HV
REGULATION
Page 64
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
X-RAY
PROTECT
Page 65
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
SOUND
PATH
Page 66
CONVERGENCE CIRCUIT
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
Page 67
MODELS: WS-48313 / WS-48413 / WS-55313 / WS-55413 / WS-65313 / WS-65413
CONTROL CIRCUIT
Page 68