Siemens SICLOCK TC 400 Operating instructions

Operating Instructions /20
SICLOCK TC400
Plant Central Clock
SICLOCK
s
s
Preface, Table of contents
Safety Information
SICLOCK® TC400
Plant Central Clock
Description
Hardware Description
Operation Planning
Operating Instructions
Installation
Connecting
Configuration Tool
Parameterization
Parameterization and Operation on the Device
Parameter Table
Service and Maintenance
Messages
Technical Data
Dimension Drawing
Circuit Diagrams
Spare Parts / Accessories
Appendix
ESD Guidelines
List of Symbols
Glossary, Index
11/2012
A2B00073596-02
Safety notices
This manual contains information that must be observed to ensure your personal safety and to prevent
property damage. The notices referring to your personal safety are highlighted in the manual by a safety
alert symbol, notices referring to property damage only, have no safety alert symbol. Depending on the
hazard level, warnings are displayed in descending order as follows:
Danger
indicates that death or serious injury will result if proper precautions are not taken.
Warning
indicates that death or serious injury may result if proper precautions are not taken.
Caution
with a warning triangle indicates that minor personal injury can result if proper precautions are not taken.
Caution
without a warning triangle means that material damage can occur if the appropriate precautions are not
taken.
Notice
means an undesirable result or state can occur if the corresponding instruction is not followed.
In the event of a number of levels of danger prevailing simultaneously, the warning corresponding to the
highest level of danger is always used. A warning with a warning triangle indicating risk of physical injury
may also include a warning of the risk of damage to property.
Qualified personnel
The associated device/system may only be installed and used in conjunction with this documentation.
Only qualified personnel should be allowed to commission and operate the device/system. For the purpose of the safety information in this documentation, a “qualified person” is someone who is authorized to
energize, ground, and tag equipment, systems, and circuits in accordance with established safety procedures.
Intended use
Please note the following:
Warning
This equipment is only allowed to be used for the applications described in the catalog and in the technical
description, and only in conjunction with non-Siemens equipment and components recommended by Siemens. Correct transport, storage, installation and assembly, as well as careful operation and maintenance,
are required to ensure that the product operates safely and without faults.
Registered Trademarks
All designations with the trademark symbol ® are registered trademarks of Siemens AG. Other designations in this documentation may be trademarks whose use by third parties for their own purposes can violate the rights of the owner.
Disclaimer of liability
We have checked that the contents of this publication agree with the hardware and software described
here. Nevertheless, we cannot assume responsibility for any deviations that may arise. The information
given in this publication is reviewed at regular intervals and any corrections that might be necessary are
made in the subsequent editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NUREMBERG
GERMANY
© Siemens AG 2007
Technical data subject to change
Preface
This document is a compilation of the information required for the operation and
parameterization of the SICLOCK TC400 plant central clock.
Scope
This manual is valid for the SICLOCK® TC400 product with firmware version V1.0
and processor version V1.0 in conjunction with the SICLOCK TC400 configuration tool as of Version 1.0.
Recycling and disposal
The SICLOCK TC400 is environmentally friendly and is thus recyclable. To recycle and dispose of your old device in an environmentally friendly way, please contact a company certified to deal with electronic waste.
Technical Assistance
If you have any technical questions, please contact Technical Assistance:
Phone:
+49 (911) 895-59 00
Monday to Friday, 8 am – 5 pm CET
Fax:
+49 (911) 895-59 07
E-Mail:
siclock@siemens.com
The latest information on SICLOCK products, product support and FAQs can be
found on the Internet:
• http://www.siemens.de/siclock (German)
• http://www.siemens.com/siclock (international)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400 Operating Instructions
Preface-3
Preface
Preface-4
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400 Operating Instructions
Table of contents
Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface-3
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents-5
1
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-9
2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-13
2.1
Configuration of the SICLOCK TC400 hardware . . . . . . . . . . . . . . .
2-14
2.2
External synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-15
2.3
2.3.1
2.3.2
Time receivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plant synchronization via Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . .
Plant synchronization via point-to-point connection . . . . . . . . . . . . .
2-16
2-16
2-17
2.4
Time management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-18
2.5
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-18
2.6
Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-19
Hardware Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-21
3.1
External design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-21
3.2
Connection elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-22
3.3
Operator controls and displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-23
3.4
Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-25
Operation Planning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-27
4.1
Overview of operation planning. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-27
4.2
Transport and storage conditions . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-29
4.3
Unpacking and checking the delivery . . . . . . . . . . . . . . . . . . . . . . . .
4-30
4.4
4.4.1
4.4.2
4.4.3
Mounting position and fixing method. . . . . . . . . . . . . . . . . . . . . . . . .
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Permitted mounting position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fixing method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-31
4-31
4-32
4-32
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-33
5.1
Installation overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-33
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-35
6.1
Connecting overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-35
6.2
Connecting the power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-36
3
4
5
6
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Contents-5
Table of contents
7
8
9
6.3
6.3.1
6.3.2
6.3.3
6.3.4
Connecting the external synchronization . . . . . . . . . . . . . . . . . . . . .
SICLOCK GPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SICLOCK DCFRS industrial version . . . . . . . . . . . . . . . . . . . . . . . . .
SICLOCK GPSDEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Third-party systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-37
6-39
6-40
6-41
6-42
6.4
6.4.1
6.4.2
Connecting the time receivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Point-to-point connections via OUTPUT 1 to 3 . . . . . . . . . . . . . . . . .
Redundant point-to-point connections. . . . . . . . . . . . . . . . . . . . . . . .
6-43
6-43
6-45
6.5
Connecting an alarm output and a warning output . . . . . . . . . . . . . .
6-46
Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-47
7.1
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-50
7.2
7.2.1
7.2.2
General functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Establish/disconnect online connection. . . . . . . . . . . . . . . . . . . . . . .
Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-52
7-53
7-54
7.3
7.3.1
7.3.2
7.3.3
7.3.4
Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sorting the parameter table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Showing/hiding parameter table entries . . . . . . . . . . . . . . . . . . . . . .
Editing parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading parameters / writing parameters / resetting parameters
to factory setings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-55
7-59
7-59
7-60
7-62
7.4
7.4.1
7.4.2
Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sorting the archive table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-63
7-66
7-67
7.5
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-68
Parameterization and Operation on the Device . . . . . . . . . . . . . . . . . . . . . .
8-71
8.1
Operating display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-72
8.2
8.2.1
8.2.2
8.2.3
Operation and parameterization . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorization (enter password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-74
8-75
8-76
8-77
Parameterization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-79
9.1
9.1.1
9.1.2
9.1.3
Linking the external synchronization . . . . . . . . . . . . . . . . . . . . . . . . .
Radio clocks via terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation as NTP client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-80
9-80
9-81
9-82
9.2
9.2.1
9.2.2
9.2.3
9.2.4
9.2.5
Linking the time receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NTP server service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SIMATIC method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OUTPUT 1 to 3 via terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OUTPUT 1 and 2 redundant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output telegram (for OUTPUT 1 to 3) . . . . . . . . . . . . . . . . . . . . . . . .
9-83
9-83
9-84
9-85
9-86
9-87
Contents-6
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Table of contents
9.3
9.3.1
9.3.2
9.3.3
9.3.4
9.3.5
9.3.6
General settings on the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-88
9-88
9-89
9-90
9-90
9-91
9-91
10
Parameter Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-93
11
Service and Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-105
11.1
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-105
11.2
Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-105
11.3
Software update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-106
12
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-107
13
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-111
14
Dimension Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-115
15
Circuit Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-117
Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-117
16
Spare Parts / Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16-119
A
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-121
A.1
Directives and declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-121
A.2
Certificates and approvals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-122
ESD Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-123
B.1
Electrostatic sensitive devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-123
B.2
Electrostatic charging of persons . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-124
B.3
Basic measures to protect against the
discharge of static electricity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-125
C
List of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C-127
D
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-129
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index-135
15.1
B
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Contents-7
Table of contents
Contents-8
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Safety Information
1
Caution
Please observe the safety instructions on the back of the cover sheet of this documentation. You should not make any expansions to your device unless you have
read the relevant safety instructions.
If you have questions about the validity of the installation in the planned environment, please contact your service representative.
Repairs
Only authorized personnel are permitted to repair the device.
Warning
Unauthorized opening and improper repairs can cause considerable damage to
property or danger for the user.
System expansions
Only install system expansions intended for this device. If you install other
upgrades, you may damage the system or violate the safety requirements and
regulations for radio frequency interference suppression.
Contact your technical support team or where you purchased your device to find
out which system expansion devices may safely be installed.
Caution
If you install or exchange system expansions and damage your device, the warranty becomes void.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
1-9
Safety Information
Safety information
Siemens offers IT security mechanisms for its automation and drive product portfolio in order to support the safe operation of the plant/machine. Our products are
also continuously developed further with regard to IT security. We therefore
recommend that you keep yourself informed about updates and upgrades for our
products and always use the latest version of each product. For information on
this topic, refer to: Industry Online Support (http://www.siemens.com/automation/csi_de_WW). You can register for a product-specific newsletter here.
For the safe operation of a plant/machine, however, it is also necessary to integrate the automation components into an overall IT security concept for the entire
plant/machine which corresponds to state-of-the-art IT technology. You can find
information on this at: Industrial Security (http://www.siemens.com/industrialsecurity).
Products used from other manufacturers should also be taken into account here.
Network security
In order to protect the entire plant from attacks on network security, corresponding measures must be taken.
Caution
Failures or damage to your overall system
Unauthorized persons can gain entry into your network via the Ethernet ports and
make changes to the SICLOCK TC400 parameterization. This can result in the
time being adjusted. Individual or even all clients to be synchronized can be removed from the synchronization cycle. This has the potential to cause failures or
damage throughout the plant.
Please adhere to the following safety measures:
− Ensure that your network is protected against unauthorized access by installing a firewall at all Ethernet ports.
− Change the default password immediately after commissioning.
− Limit the number of people to whom this password is known to the absolute
minimum.
− Change the password regularly.
1-10
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Safety Information
Battery
This device is equipped with a Lithium battery. Batteries may only be replaced by
qualified personnel. See also Battery (Section 11.1).
Caution
There is the risk of an explosion if the battery is not replaced as directed. Replace
only with the same type or with an equivalent type recommended by the manufacturer. Dispose of used batteries in accordance with local regulations.
Warning
Risk of explosion and release of harmful substances!
Therefore, do not throw Lithium batteries into an open fire, do not solder or open
the cell body, do not short-circuit or reverse polarity, do not heat up above 100°
C, dispose as regulated and protected against direct exposure to sunlight, humidity and condensation.
ESD guidelines
Modules containing electrostatic sensitive devices (ESDs) can be identified by the
following label:
Strictly follow the guidelines mentioned below when handling modules which are sensitive
to ESD:
• Always discharge your body's static electricity before handling modules which
are sensitive to ESD (for example, by touching a grounded object).
• All devices and tools must be free of static charge.
• Always pull the mains connector and disconnect the battery before you install
or remove modules which are sensitive to ESD.
• Handle modules fitted with ESDs by their edges only.
• Do not touch any connector pins.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
1-11
Safety Information
1-12
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Description
2
Modern automation systems consist of a variety of computers, controllers and
systems that exchange data with one another. For real-time operation of such
plants, it is essential that the times of all components are synchronous. This
applies especially for error tracing, when event messages receive a time stamp
and when cause and effect have to be identified through a reliable chronological
sequence.
As plant central clock, SICLOCK TC400 supplies the various plant components
with the exact and reliable time, which is obtained from one or more external synchronizations with an official or legal time, usually GPS or DCF77 radio clocks.
The time is distributed via Ethernet, and also via point-to-point outputs.
Note
Use only one device as plant central clock to supply the time to all components
throughout the plant.
Exception: redundant operation of the plant central clock.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
2-13
Description
2.1
Configuration of the SICLOCK TC400 hardware
The following figure shows a connection example of the SICLOCK TC400 to a
SICLOCK GPS1000 as radio clock and an NTP server as an additional external
synchronization.
([WHUQDOV\QFKURQL]DWLRQV
([WHUQDOV\QFKURQL]DWLRQ
6,&/2&.7&
6,&/2&.*36
;
([WHUQDOV\QFKURQL]DWLRQ
287387
287387
287387
5$',2&/2&.
5$',2&/2&.
1736HUYHU
3&21
$ODUPZDUQLQJ
,QVWUXPHQWDWLRQ
DQGFRQWURO
,QVWUXPHQWDWLRQ
DQGFRQWURO
$/$50
:$51,1*
7LPHUHFHLYHUV
5HFHLYHUVYLD
FXUUHQWVLJQDO
YROWDJHVLJQDO
(WKHUQHW3RUWV
5HFHLYHUVYLD
3&21
3&21
6
3&
6
Arbeitsstation
3&
3&21
6,&/2&.3&21
HOHFWULFDORSWLFDOSXOVHFRQYHUWHURSWLRQDO
Arbeitsstation
3&
Arbeitsstation
Figure 2-1 Application example
2-14
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Description
2.2
External synchronization
SICLOCK TC400 can be matched to the local official time or GMT via external
synchronization in order to automate or restrict manual actions, such as daylight
saving time switchovers and leap seconds, to a minimum.
External synchronizations can be GPS or DCF77 radio clocks, servers (e.g. time
signal from an NTP server), further SICLOCK TC400 devices or other signal
sources. They are connected to RADIO CLOCK 1 or RADIO CLOCK 2 or to one
of the four Ethernet ports on the device.
NTP servers are supported as external synchronization on the Ethernet ports.
Possible radio clocks to RADIO CLOCK 1 and RADIO CLOCK 2:
• SICLOCK GPS1000
• SICLOCK GPSDEC
(SICLOCK GPSDEC has been discontinued, please use SICLOCK GPS1000)
• SICLOCK DCFRS
Third-party products can be connected via TTY (passive). The following protocols
are supported:
• Demodulated DCF77
• Serial:
− Meinberg compatible (including time zones)
− Meinberg compatible (not including time zones)
− NMEA (0183/ZDA)
Further information
Linking the external synchronization (Section 9.1)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
2-15
Description
2.3
Time receivers
The time receivers of the plant can be connected via Ethernet or directly on the
device via point-to-point connections.
2.3.1
Plant synchronization via Ethernet
Physical access
There are four Ethernet interfaces available as physical access to the network
with the following specification:
• 100Base TX via RJ-45 socket
Protocols
The following protocols have been implemented:
• NTP server according to RFC2030
− Any/unicast mode
− Multicast mode
− Multicast mode with local time
• Time synchronization with the SIMATIC method
− PCS7-compatible mode
− S5-compatible mode
The time message frames can be transmitted to each Ethernet port individually either every second or every 10 seconds.
2-16
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Description
2.3.2
Plant synchronization via point-to-point connection
Non-networked plant equipment is synchronized via OUTPUTs 1 to 3 (point-topoint connections). They can be parameterized independently.
OUTPUTs 1 and 2
• Current signal: 20 mA active, floating
or
• Voltage signal: 24 V, floating
OUTPUT 3
RS422, floating
Output signal
• DCF77 with local time, invertible
• DCF77 with UTC, invertible
• Pulse per second, invertible
• Pulse per minute, invertible
• Serial telegram (parameterizable output telegram, see below)
Output telegram (setting applies to all three outputs)
• Meinberg compatible (including time zones)
• Meinberg compatible (not including time zones)
• NMEA (0183/ZDA)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
2-17
Description
2.4
Time management
Various functions are available in SICLOCK TC400 in order to generate the time
valid for the plant from the external synchronization. This includes setting options
for time zones as well as the parameterizable daylight saving time.
Time assurance through protected synchronization
If a discontinuity of more than 5 s occurs in the external synchronization, the protected synchronization is activated and, for safety reasons, the synchronization
not performed.
Time assurance through microstepping mode
A time difference between the external synchronization and the device, which can
occur through a temporary radio failure or switchover to a substitute synchronization, is automatically cleared unnoticeably in microstepping mode for the plant
operation. There is no inconsistency in the time.
Further information and parameterization options for protected synchronization
and the microstepping mode are described in Section Synchronization
(Section 9.3.2).
Note
Only parameterize the plant time at one location within the synchronization hierarchy, ideally at the plant central clock.
2.5
Commissioning
The commissioning can be divided into the following steps:
1. Installation (Section 5)
2. Connecting (Section 6)
3. Assigning IP address on the device
Parameterization and Operation on the Device (Section 8)
4. Parameterization (Section 9)
With a few exceptions, the settings are made with the configuration tool, see
Configuration Tool (Section 7).
2-18
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Description
2.6
Redundancy
Redundant external synchronization
Up to two radio clocks and up to four time servers can be operated on the
SICLOCK TC400 for the external synchronization.
The priorities of the external synchronizations and therefore the redundancy
behavior can be set via parameters, see Redundancy (Section 9.1.3).
Redundant SICLOCK TC400 plant central clock
A SICLOCK TC400 can be operated via various ports on a redundant network
and several SICLOCK TC400 can be operated as servers on one network.
For further information, refer to Chapters Configuration Tool (Section 7) and
Parameter Table (Section 10).
Redundant control of time receivers (output redundancy)
At least two SICLOCK TC400 are used for an output redundancy. With the appropriate parameterization, OUTPUTs 1 and 2 of the two devices can each be connected redundantly with the other.
For further information, refer to Sections Redundant point-to-point connections (Section 6.4.2) and OUTPUT 1 and 2 redundant (Section 9.2.4).
You can find more information on redundancy in
„Application Note 0108“ on http://www.siemens.com/siclock under "FAQ".
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
2-19
Description
2-20
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Hardware Description
3
This chapter describes the hardware design with connections, the operator controls and displays.
3.1
External design
The following figures show the displays and operator controls as well as the connections of the SICLOCK TC400.
Figure 3-1 SICLOCK TC400 - perspective view with front panel and ventilation grille
(1)
Panel with operator controls and displays
(2)
Ventilation grille
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
3-21
Hardware Description
3.2
Connection elements
The following figure shows the connections of the SICLOCK TC400.
Figure 3-2 SICLOCK TC400 - arrangement of the connections
(1)
Terminal X1 - 24 V power supply
(2)
Terminal X2 - connecting terminal for radio clocks, outputs and alarm
See also Terminal assignment (Section 15.1).
(3)
Four Ethernet ports
3-22
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Hardware Description
3.3
Operator controls and displays
The front panel shows the current mode in the display and with LEDs. The device
can be operated directly via the keypad. A Web-based configuration tool is available for a wide range of configuration options, see Configuration Tool
(Section 7).
Figure 3-3 SICLOCK TC400 front view
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
3-23
Hardware Description
Table 3-1
Meaning of the displays and operator controls
Name
Color (LED)
Meaning
Displays
POWER
Green
Ready to run
SYNC
Green
SICLOCK TC400 has been externally synchronized
FAULT
Red
Alarm
The associated message text is shown in the display.
Flashing red Warning
The associated message text is shown in the display.
LINK (Port 1-4)
Yellow
Physical connection has been established, possible to send
and receive
ACTIVE (Port 1-4)
Green
Display of the data traffic for the respective port
RADIO CLOCK 1
Yellow
Receive signal of radio clock 1
RADIO CLOCK 2
Yellow
Receive signal of radio clock 2
OUT 1
Green
Output 1
Output signal at the terminal
OUT 2
Green
Output 2
Output signal at the terminal
OUT 3
Green
Output 3
Output signal at the terminal
Display
Display of time, date and synchronization or message text
when an error occurs
Operator controls
SETUP
Call of the password input or parameter list
↑↓←→
Navigation in the menus
ESC
• Cancellation of an entry and return to the call menu.
• Switchover from an information message or warning to the
mode display
• Change to operator control for a limited period when a persistent message is pending.
OK
Accepting of entries and acknowledging of messages
For further information, see Parameterization and Operation on the Device
(Section 8).
3-24
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Hardware Description
3.4
Scope of delivery
Table 3-2
Scope of delivery of the individual device versions
2XV9450-2AR01
SICLOCK TC400 single device with terminal strips connected at X1 and X2
2XV9450-2AR10 (SICLOCK TC400 standard package)
SICLOCK TC400 single device with terminal strips connected at X1 and X2
SICLOCK GPS1000 radio clock complete with mounting frame and lightning protection
2XV9450-2AR20 (SICLOCK TC400 DCF77 package)
SICLOCK TC400 single device with terminal strips connected at X1 and X2
SICLOCK DCFRS radio clock industrial version complete with mounting frame
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
3-25
Hardware Description
3-26
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Operation Planning
4.1
4
Overview of operation planning
SICLOCK TC400 has been designed for weather-protected, stationary operation
in an industrial environment.
The operating conditions surpass the requirements according to DIN IEC 607213-3:
• Class 3M3 (mechanical requirements)
• Class 3K3 (climatic requirements)
General information about operation
Caution
The device is approved for operation in closed rooms only. The guarantee is void
if this stipulation is ignored.
Condensation
When transporting the device at low temperatures, ensure that no moisture forms
on or in the device. This also applies if the device is subjected to extreme changes
in temperature.
Commissioning
Allow the device to slowly adjust to room temperature before commissioning. Do
not place the device near heat radiation. With large differences in temperature,
harmful condensation can be avoided by leaving the device in the transport packaging.
If condensation occurs, wait at least about 12 hours before you switch on the
device (for 20° C temperature difference). The waiting period is extended accordingly for greater temperature differences.
Avoid extreme ambient conditions. Protect your device against dust, moisture and
heat. For further information, see Chapter Technical Data (Section 13).
Do not place the device in direct sunlight.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
4-27
Operation Planning
Use in residential areas and operation in the public network
If you operate the SICLOCK TC400 in residential areas or in the public network,
you must ensure that it complies with the limit class B according to EN 55022 with
regard to the emission of radio interference.
Note
This is a a class A device. The device may cause RF interference in residential
areas or in the public network. In this case, the operator company may be held
liable for taking appropriate measures.
The following measures are recommended to ensure the interference complies
with limit class B:
• Installation of the SICLOCK TC400 in grounded control cabinets / control
boxes
• Use of filters in electrical supply lines
Use with additional measures
Applications where the use of the SICLOCK TC400 or similar device requires
additional measures:
• Locations with a high percentage of ionizing radiation
• Locations with extreme operating conditions, such as
− dust accumulation
− corrosive vapors or gases
− strong electric or magnetic fields
− damp and wet rooms
− strong oscillations, shocks, vibrations
− strong radiant heat
• In systems, which require special monitoring, such as
− elevators
− electrical plants in potentially hazardous areas
An additional measure, for example, would be to install the SICLOCK TC400 in a
cabinet or housing.
4-28
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Operation Planning
4.2
Transport and storage conditions
Although the device is of rugged design, its internal components are sensitive to
severe vibrations or shock. You must therefore protect the device against severe
mechanical loads.
You should always use the original packaging for shipping and transporting the
device.
Unpack the device at its final destination.
Do not transport the device when it is mounted.
Observe the notes about temporary storage in Chapter Service and Maintenance under Battery (Section 11.1).
The following information applies to modules transported and stored in the original packaging.
The climatic environmental conditions correspond to IEC 60721-3-2, Class 2K4
for transport
The mechanical environmental conditions correspond to IEC 60721-3-2, Class
2M2 for transport
Caution
Risk of damage to the device!
If you are transporting the device in cold weather with large fluctuations in temperature, care must be taken to ensure that no moisture forms on or in the device
(condensation).
If condensation has developed, wait at least 12 hours before you switch on the
device.
Caution
Observe these conditions each time the device is transported, otherwise the guarantee is void.
Table 4-1
Transport and storage conditions
Type of condition
Permissible range
Free fall (in transport packaging)
<= 1 m
Temperature
-40° C to +70° C
Atmospheric pressure
1080 to 660 hPa (corresponds to an altitude
of -1000 to 3500 m)
Maximum temperature change
20° C/h
Relative humidity
10 to 95% (at 25° C without condensation)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
4-29
Operation Planning
4.3
Unpacking and checking the delivery
The device has been completely assembled, tested and packed in the factory and
has no internal transport locks.
If there are large temperature differences between the transport medium and the
location where the device is unpacked, it is recommended that the device be left
in the transport packaging in order to avoid harmful condensation.
Procedure
• Please check the packaging material for transport damage upon delivery.
• If any transport damage is present at the time of delivery, lodge a complaint at
the shipping company in charge. Have the shipper confirm the transport damage immediately.
• Unpack the device.
• Keep the packaging material in case you have to transport the device again.
Caution
The packaging protects the device during transport and storage. Transport the
device only in the original packaging!
• Please keep the enclosed documentation in a safe place. You will need the
documentation when you commission the device for the first time.
• Check the package contents for completeness and any visible transport damage. Check for completeness using the enclosed "Contents of Delivery" list.
• Notify the delivery service in charge immediately if the package contents are
incomplete or damaged.
Warning
Make sure that a damaged device is not installed and commissioned unintentionally.
4-30
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Operation Planning
4.4
Mounting position and fixing method
4.4.1
Installation instructions
Before installing the device, read the following general installation instructions.
Warning
Hazardous voltage
Isolate the power supply to the control cabinet before opening it. Ensure that the
power to the control cabinet cannot be turned on accidentally.
• Position the device/display in an ergonomic position favorable to the user.
Choose a suitable installation height.
• Position the device/display so that it is not subject to direct sunlight or other
strong sources of light.
• Provide adequate volume in the control cabinet for air circulation and heat
transport. Maintain a clearance of 100 mm above and below. This clearance
is increased accordingly with connection cables.
• Position the device so that the air vents of the housing are not covered up following installation.
• Also provide enough free space for device expansions.
• Note the reinforcement in the control cabinet for stabilizing the installation cutout. Install reinforcement if required.
• Install the device in such a way that there is no danger, for example, of it falling
out.
• During assembly, please comply with the permissible mounting positions.
See also Dimension Drawing (Section 14).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
4-31
Operation Planning
4.4.2
Permitted mounting position
The only permissible mounting position is horizontal, i.e. the display is read horizontally. Adequate ventilation cannot be guaranteed in other mounting positions
Figure 4-1 Horizontal mounting position
4.4.3
Fixing method
The housing can be snapped onto DIN rails or fixed to SIMATIC S5 standard
mounting rails.
See also Installation overview (Section 5.1).
4-32
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Installation
5.1
5
Installation overview
Figure 5-1 SICLOCK TC400 - installation view
The SICLOCK TC400 should be installed in the control cabinet at an easily accessible position.
The housing can be snapped onto DIN rails (EN 50022-35) or fixed to SIMATIC
S5 standard mounting rails (6ES5 710-8maxx).
There must be a space of 100 mm above the device for snapping the device on
and off the DIN rail and for unobstructed heat dissipation.
There must be a space of at least 100 mm below the device for the process signal
connectors.
It is recommended that a suitable cable duct be installed below this space.
Note
Ensure that the snap fasteners are correctly locked.
See also Dimension Drawing (Section 14).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
5-33
Installation
5-34
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Connecting
6.1
6
Connecting overview
Caution
Only connect I/O devices that are suitable for industrial use.
Caution
Strictly adhere to the specifications for I/O devices.
Note the following requirements for the setup:
• The device may only be connected to 24 VDC power supplies that meet the
requirements of a functional extra-low-voltage with safe isolation (PELV). The
cable cross-section must be chosen to ensure that no damage can result from
a cable overheating in the event of a short-circuit in the SICLOCK TC400. For
cable cross-section, see Connecting the power supply (Section 6.2).
• Avoid extreme environmental conditions as far as possible.
• Protect the device against dust, moisture, heat and severe vibration.
• Do not place the device in direct sunlight.
• Install the device in such a way that it does not present a hazard (e.g. by falling
out).
• Do not cover the vent slots.
• Permitted mounting position (Section 4.4.2).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
6-35
Connecting
6.2
Connecting the power supply
The power supply is connected to the X1 terminal strip and must always be via a
time-lag 1 A fuse. The device does not have a separate power switch.
Figure 6-1 Connecting the power supply
Note before connecting
Warning
Only connect the device to 24 VDC power supplies that meet the requirements of
a functional extra-low voltage with safe isolation (PELV); in addition, a protective
conductor must also be connected. The cable cross-section must be matched to
the short-circuit current of the 24 VDC power supply, so that with a short-circuit,
damage is not caused by the cable. Only connect cables with a cross-section of
minimum 0.25 mm2 (AWG23) to maximum 2.50 mm2 (AWG13).
Notice
The 24 VDC power supply must be adapted to the input data of the device, see
Technical Data (Section 13).
Caution
Ensure that the functional ground is connected correctly.
Make sure the polarity is correct for DC voltage.
Functional check
After switching on, the POWER LED must show a green light.
6-36
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Connecting
6.3
Connecting the external synchronization
The signal of the connected radio clock is detected automatically and displayed
in the /Inputs/Input 1/Status (0.20.02) parameter (or /Inputs/Input 2/Status
(0.21.02) parameter).
X2-7
X2-8
48 V
X2-9
passive
Radio Clock 1
X2-10
48 V
X2-11
passive
Radio Clock 2
X2-7
X2-8
active
Radio Clock 1
48 V
X2-9
X2-10
active
Radio Clock 2
48 V
X2-11
Figure 6-2 Circuit diagram for a passive and an active radio clock
Table 6-1
Terminal assignment of the radio clock inputs
Terminal
Designation
X2-7
RADIO CLOCK GND
X2-8
RADIO CLOCK 1A
X2-9
RADIO CLOCK 1B
X2-10
RADIO CLOCK 2A
X2-11
RADIO CLOCK 2B
Note
If you are operating two radio clocks, connect the preferred model to RADIO
CLOCK 1.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
6-37
Connecting
Functional check
The receive signal of the radio clocks is displayed on the front panel with the
"RADIO CLOCK 1" and "RADIO CLOCK 2" LEDs.
The status of the radio clock is displayed in the /Inputs/Input 1/Status (0.20.02) (or
/Inputs/Input 2/Status (0.21.02)) parameter.
Possible states:
• GPS (SICLOCK GPS1000 and SICLOCK GPSDEC)
• GPS (faulty)
The signal reception is temporarily faulty.
• DCF77 (SICLOCK DCFRS and SICLOCK GPSDEC)
• DCF77 (faulty)
The signal reception is temporarily faulty.
• Serial
− Meinberg
Receiving Meinberg format
− NMEA
Receiving NMEA format
− Telegram (faulty)
Fault detected in telegram or telegram failure
• No signal
The connection of individual sources to the external synchronization is described
in the following.
6-38
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Connecting
6.3.1
SICLOCK GPS1000
The GPS1000 receiver is connected as shown in Fig. 6-3.
;
6
7
5$',2&/2&.*1'
5$',2&/2&.$
8
9
5$',2&/2&.$
10
5$',2&/2&.%
11
/LJKWQLQJSURWHFWLRQ
PD[P
5$',2&/2&.%
Figure 6-3 SICLOCK GPS1000 radio clock connection to RADIO CLOCK 1
We recommend a 2-wire, shielded cable, e.g. LiYCY 2x1 mm², as radio clock
cable. The cable shield should be connected one-sided to a suitable place at the
installation location.
An additional parameterization of the GPS1000 is not required.
Warning
Use lightning protection for the outdoor GPS antenna.
Functional check
When the GPS1000 is receiving correctly, the "RADIO CLOCK 1" or "RADIO
CLOCK 2" LED on the front panel should flash at approx. 1 Hz.
After receiving for approximately three minutes the /Inputs/Input 1/Status
(0.20.02) or /Inputs/Input 2/Status (0.21.02) parameter must change to "GPS".
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
6-39
Connecting
6.3.2
SICLOCK DCFRS industrial version
The industrial version of the SICLOCK DCFRS radio clock contained in the
DCF77 package is connected as shown in Fig. 6-4. The polarity is not important
here.
max. 1000 m
;
6
7
5$',2&/2&.*1'
5$',2&/2&.$
8
9
5$',2&/2&.$
10
5$',2&/2&.%
11
5$',2&/2&.%
Figure 6-4 SICLOCK DCFRS industrial version radio clock connection to
RADIO CLOCK 1
Warning
Lightning protection must also be installed when used outdoors.
Note
The radio clock cable shield should be connected one-sided to a suitable place at
the installation location.
Functional check
When the SICLOCK DCFRS is receiving correctly, the "RADIO CLOCK 1" or
"RADIO CLOCK 2" LED on the front panel should flash at approx. 1 Hz.
After receiving for approximately three minutes the /Inputs/Input 1/Status
(0.20.02) or /Inputs/Input 2/Status (0.21.02) parameter must change to "DCF77".
Note
When selecting the location for the antenna, it is especially important that there is
as little electromagnetic interference on the DCF77 carrier frequency as possible.
Do not mount the antenna close to drives, neon lamps, monitors and other emitters of interference.
6-40
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Connecting
6.3.3
SICLOCK GPSDEC
(SICLOCK GPSDEC has been discontinued, please use SICLOCK GPS1000)
A SICLOCK GPSDEC decoder is connected as shown in Fig. 6-5.
'&)77<
;
6
7
5$',2&/2&.*1'
5$',2&/2&.$
8
9
5$',2&/2&.$
10
5$',2&/2&.%
11
PD[P
5$',2&/2&.%
Figure 6-5 SICLOCK GPSDEC radio clock connection to RADIO CLOCK 1
Caution
The SICLOCK GPSDEC may only be operated as active radio clock.
Operation as passive radio clock results in the destruction of the SICLOCK GPSDEC.
Table 6-2
Recommended parameterization of the GPSDEC decoder for the
SICLOCK TC400 synchronization
Parameter
Setting
Time difference compared to GMT
00:00
Switchover to daylight saving time
"None"
X1.5-8 (DCF77TTY)
"DCF without ZZB"
Functional check
When the GPSDEC is receiving correctly, the "RADIO CLOCK 1" or "RADIO
CLOCK 2" LED on the front panel should flash at approx. 1 Hz.
After receiving for approximately three minutes the /Inputs/Input 1/Status
(0.20.02) or /Inputs/Input 2/Status (0.21.02) parameter must change to "GPS" or
"DCF77".
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
6-41
Connecting
6.3.4
Third-party systems
Third-party systems that fulfill the following requirements can be sued for the
external synchronization of the SICLOCK TC400.
Requirements
• Active radio clock signal with 20 mA rated current
• Supported signals:
− Demodulated DCF77
− Serial:
Meinberg compatible (including time zones)
Meinberg compatible (not including time zones)
NMEA (0183/ZDA)
Functional check
After receiving for approximately three minutes the /Inputs/Input 1/Status
(0.20.02) or /Inputs/Input 2/Status (0.21.02) parameter must change to "Meinberg", "NMEA" or "DCF77".
6-42
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Connecting
6.4
Connecting the time receivers
Time receivers can be connected via point-to-point connections (OUTPUT 1 to 3)
or via Ethernet.
Four Ethernet ports are available for the Ethernet connection and can be parameterized accordingly.
A redundant point-to-point connection can be implemented via OUTPUTs 1 and
2 when two SICLOCK TC400s are used.
6.4.1
Point-to-point connections via OUTPUT 1 to 3
Current signal – low-resistance receiver (e.g. optocoupler)
Point-to-point connections via an active current interface can be connected to
OUTPUTs 1 and 2 as shown in Fig. 6-6.
77<DFWLYH
1
2
24 V / 20 mA
3
4
Figure 6-6 OUTPUTs 1 and 2 as current interface
Table 6-3
Terminals of OUTPUTs 1 and 2
Terminal
Designation
1
OUTPUT 1 GND
2
OUTPUT 1
3
OUTPUT 2
4
OUTPUT 2 GND
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
6-43
Connecting
24 V voltage signal – high-resistance receiver (greater than 1.2 kOhm)
A high-resistance receiver can also be connected directly. The output then functions as a 24 V voltage output.
Connection as in Fig. 6-6.
RS422
An RS422 interface is available at OUTPUT 3 for a high-precision point-to-point
connection. The connection is made as shown in Fig. 6-7.
RS422
5
A
6
B
Figure 6-7 OUTPUT 3 RS422
Table 6-4
OUTPUT 3 terminals
Terminal
6-44
Designation
5
OUTPUT 3A
6
OUTPUT 3B
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Connecting
6.4.2
Redundant point-to-point connections
OUTPUT 1 and OUTPUT 2 of the devices are decoupled internally so that one
output of each device can be connected in parallel to the same time receiver.
ಹ
ಹ
287387
287387
287387*1'
287387*1'
6,&/2&.
287387
287387
287387*1'
287387*1'
6,&/2&.
ಹ
7LPHUHFHLYHU
ಹ
7LPHUHFHLYHU
7LPHUHFHLYHU
UHGXQGDQWWLPHIURPERWK
6,&/2&.DQG
UHVSHFWLYHO\
Figure 6-8 Example with redundant time reception at OUTPUT 1
Further information
Redundancy (Section 2.6)
OUTPUT 1 and 2 redundant (Section 9.2.4)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
6-45
Connecting
6.5
Connecting an alarm output and a warning output
The SICLOCK TC400 automatically performs various functional tests during
operation. When an error occurs, the appropriate messages are generated on the
display. A distinction is made between alarms and warnings.
An alarm output and a warning output are available on terminal X2 for the external
monitoring.
;
;
;
Figure 6-9 Alarm output X2-13 and warning output X2-14
Table 6-5
Parameters that influence the alarm response
/Synchronization/Advanced/Monitoring/monitor status of synchronization (0.09.14)
/Network Settings/Ethernet 1/Advanced Settings Adapter 1/monitor link state (0.05.09)
/Network Settings/Ethernet 2/Advanced Settings Adapter 2/monitor link state (0.05.10)
/Network Settings/Ethernet 3/Advanced Settings Adapter 3/monitor link state (0.05.11)
/Network Settings/Ethernet 4/Advanced Settings Adapter 1/monitor link state (0.05.12)
/NTP Client/Monitoring/monitor server (0.18.04)
/Inputs/Input 1/Monitoring/monitor input (0.20.01)
/Inputs/Input 2/Monitoring/monitor input (0.21.01)
/Environment/Advanced/Temperature/monitoring (0.24.01)
Example:
The alarm output is to be set when no external synchronization is available.
With the configuration tool, set the parameter entry /Synchronization/Advanced/Monitoring/monitor status of synchronization (0.09.14) = "Alarm"
to activate the monitoring / alarm output when an error occurs.
Note
The contacts are designed as fail-safe NC contacts. The appropriate contact is
opened when an alarm or a warning is pending.
6-46
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7
Configuration Tool
The SICLOCK TC400 configuration tool is available for the easy parameterization
and configuration of the SICLOCK TC400. The tool can be called as up Web interface via an Internet browser.
With the configuration tool, you can view and change parameters online and
offline, view archives and perform searches in them with filter criteria and load,
save and change the parameterization of the SICLOCK TC400 device.
Figure 7-1 SICLOCK TC400 configuration tool
(1) Toolbar of the configuration tool
(2) Working area of the configuration tool
You can make settings and assign parameters in the Parameters tag
You can check states and search for events in the Archives tag
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-47
Configuration Tool
Requirements
PC
• Screen resolution of at least 1280x1024 pixels
• Java Runtime, at least V1.4.0 or higher
• Web browser, e.g. Microsoft Internet Explorer
• Connection via one of the four Ethernet ports of the device
SICLOCK TC400
• Assignment of an IP address on the device
A valid IP address must be assigned for the Ethernet port of the device that is
to be used for the configuration.
Default addresses as delivered each with subnet mask 255.255.255.0:
− Port 1: 192.168.1.10
− Port 2: 192.168.2.20
− Port 3: 192.168.3.30
− Port 4: 192.168.4.40
PC must be in the same subnet.
Parameters, entries and lists
A parameter is considered as a group of associated values. Each value is designated as an entry of its parameter.
Parameters of the same kind can form a list. Such lists are displayed as [ ].
Notice
Entries can be edited individually, but not read or written individually. The parameter is always read or written with all its entries. If a list is being considered, the
entire list is read or written.
Parameters are identified by their unique parameter number. The parameter
number is always in three parts, e.g. 0.05.12.
7-48
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
Example of the /Display/View (0.10.01) parameter with the entries "Language"
and "Time":
Figure 7-2 Parameter view
Working with the configuration tool
To start the configuration tool:
1. Open the Web browser.
2. Enter the address of the device port, e.g. 192.168.1.10
3. If necessary, confirm the installation and execution of the applet with "Yes" or
"Always".
−> The configuration tool is started and displayed in the browser.
Note
Note the information in your browser about restrictions because of strict safety
settings.
To parameterize the SICLOCK TC400 with the configuration tool:
1. Connect the configuration tool to the SICLOCK TC400 with the
button.
2. For a new parameterization of the device, load the parameters to the configuration tool with the
button or open an existing parameter file (*.u600) with
the
button.
3. Parameterize the SICLOCK TC400 according to your hardware configuration
and your requirements.
In online mode, changes take effect immediately on the device.
4. Save the configuration as parameter file (*.u600) on your PC with the
button.
Note
In order to be able to access the last version of the SICLOCK TC400 parameterization, we recommend that you save the current parameterization of SICLOCK
TC400 as *.u600 file before you make any changes.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-49
Configuration Tool
7.1
Menus
Table 7-1
Menus in the configuration tool
Menu/Function
Meaning/Note
File
Open
Load a parameterization/archive from the local file system
See also General functions (Section 7.2).
Save
Save of a parameterization/archive to the local file system
See also General functions (Section 7.2).
Exit
Connection
Exit the application
See also Establish/disconnect online connection (Section 7.2.1).
Connect
Connect to a device
Disconnect
Disconnect from a device
Data transfer
See also Establish/disconnect online connection (Section 7.2.1).
(online connection required)
Download parameters
from device
Download all parameters from a connected device to the PC
Refresh parameters
from device
Refresh all parameters previously loaded to the PC with the values of
the connected device
See also Parameters (Section 7.3).
See also Parameters (Section 7.3).
Upload parameters to
device
Write all parameters from the PC to the connected device
Download archive
Download the entire archive from the connected device to the PC
See also Parameters (Section 7.3).
See also Archive (Section 7.4).
Refresh archive
Re-request/refresh the archive of a connected device
See also Archive (Section 7.4).
View
Parameters
Change to the Parameters view
See also Parameters (Section 7.3).
Archive/Events
Change to the Archive/Events view
See also Archive (Section 7.4).
Language
Selection of the languages available for the user interface
Depending on the version, several languages may be offered for selection
• English (standard language)
• German
The language/naming of the parameters and archives is supplied by the
device. If the language set in the configuration tool is known to the
device, then the parameter/archive is displayed in this language. If the
language is not known to the device, the display is in the standard language.
7-50
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
Table 7-1
Menus in the configuration tool
Menu/Function
Meaning/Note
?
Help...
Call the help system
Version…
Display the version information of the configuration tool
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-51
Configuration Tool
7.2
General functions
The toolbar of the configuration tool provides general functions for the parameters
and the archive. You can also acknowledge events and authorize yourself on the
configuration tool.
Table 7-2
Operator options and displays in the toolbar of the configuration tool
Field/Button
Meaning/Instruction
Load a parameterization/archive from the local file system
Open
The file must be present in U600 format (*.u600). When opening, the
parameterization and the archive are loaded from the file.
Notice
The currently loaded data (parameterization and archive) is overwritten.
Save of a parameterization/archive to the local file system
The data (parameterization and archive) is saved in U600 format (*.u600).
Save
IP address of the SICLOCK TC400
You enter the IP address of the device here.
IP address
Connect to a device
The connection is established to the device with the specified IP address.
Connect to device
Disconnect from device
The established connection is disconnected.
See also Establish/disconnect online connection (Section 7.2.1).
Disconnect from device
Password input to activate a higher access level
Password of the device as delivered: "2222"
Authorization - password
See also Authorization (Section 7.2.2).
Perform the authorization with the entered password
Authorize
Events currently pending in the device
Event
(online connection
required)
Events pending on the device (e.g. warnings, alarms, …) are displayed in
online mode
No information is displayed in offline mode.
Acknowledge pending event
Acknowledge event
(online connection
required)
7-52
In online mode, an acknowledgement for the pending event is sent to the
device. If acknowledgeable, the device clears the event from the display.
Events that cannot be acknowledged (persistent messages) remain in the
display.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
Table 7-2
Operator options and displays in the toolbar of the configuration tool
Field/Button
Meaning/Instruction
Acknowledge all pending events
Acknowledge all events
In online mode, an acknowledgement for all pending events is sent to the
device. There is an acknowledgement even when the cause of the event is
still present. In this way it is possible, for example, to clear persistent
alarms.
Discard the pending event
The event display is cleared without interaction with the device.
Ignore event
7.2.1
Establish/disconnect online connection
To establish an online connection to the SICLOCK TC400:
1. Enter the IP address of the device in the toolbar.
2. Start the connection build-up by clicking the
field.
icon next to the IP address
−> The configuration tool changes to online mode:
To disconnect the online connection to the SICLOCK TC400:
1. Click the
icon next to the IP address field.
−> The configuration tool changes to offline mode:
Note
The device is disconnected if there have not been any operator actions for approx.
two hours
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-53
Configuration Tool
7.2.2
Authorization
There are authorization levels for each parameter, which permit or prohibit read
and write access to the parameter. The user interface starts with the lowest authorization level, which usually only permits read access to parameters.
More rights can be obtained by entering the appropriate password.
The password can be changed by the user:
• /System/Authorization For Standard Protection (2.06.02) parameter
Note
The combination "0000" is not permitted as a password. Setting the password to
"0000" disables access with this authorization level. Access is then only possible
using the service password. The service password can be requested from Technical Assistance by an authorized person.
As delivered, the password on the device is "2222"
The current authorization level is indicated by the color of the password field.
Write protection - red entry field
At this authorization level, the user typically only has read access to standard
parameters.
Standard protection - green entry field
At this authorization level, the user typically also has read access to advanced
parameters and write access to standard parameters.
Online mode
Authorization is performed directly on the device, i.e. the device assigns an
appropriate authorization level.
Offline mode
You can authorize yourself for a higher authorization level with a password, when
this is contained in the loaded offline authorization parameters.
Note
It is not possible to authorize yourself in offline mode with a password that is available on the device, but is not contained in the offline authorization parameters.
7-54
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
7.3
Parameters
You can set and transfer parameters of the SICLOCK TC400 in offline and online
mode in the Parameters tab of the configuration tool.
Figure 7-3 SICLOCK TC400 configuration tool - parameters
(1) Toolbar of the Parameters tab
(2) Parameter tree
(3) Parameter table
(4) Parameter information
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-55
Configuration Tool
Table 7-3
Operator options and displays in the Parameters tab
Field/Button
Meaning/Instruction
Output of the parameterization to a text file
Print table to text file
The currently displayed parameterization is output to a text file. The data can,
for example, be further edited with Excel.
Notice
Parameterizations cannot be restored from these text files. To restore a
parameterization, it must first have been saved in U600 format.
See Open/Save in General functions (Section 7.2).
Download parameters of the connected device
Download parameters
(online connection
required)
The parameters of the connected device including the description data (e.g.
texts in all languages) are downloaded. This can take several minutes. Implicitly the parameterization is downloaded again from the device.
Notice
The displayed parameterization data is overwritten. The archive data is not
taken over from the device, i.e. the displayed archive data is retained.
See also Establish/disconnect online connection (Section 7.2.1).
Download parameters of the connected device without parameter description
Refresh parameters
(online connection
required)
The parameters of a connected device are downloaded without the description data. This can take several minutes.
Notice
The displayed parameterization data is overwritten. The archive data is not
taken over from the device, i.e. the displayed archive data is retained.
See also Establish/disconnect online connection (Section 7.2.1).
Transfer writeable values of the loaded parameters to the connected device
The following values/parameters are not transferred to the device:
Upload parameters
•
Value of write-protected parameters
(online connection
required)
•
Critical operating parameters
•
Display parameters
• Command parameters
An online connection must be established for the transfer of the parameters
and the configuration tool must have the appropriate authorization. See also
Establish/disconnect online connection (Section 7.2.1) and Authorization (Section 7.2.2).
Monitor current value/status of actual values
Monitor actual values
(online connection
required)
7-56
After the monitoring is activated, the current values or states are cyclically
read from the device and the display in the parameter tree and parameter
table is refreshed.
See also Establish/disconnect online connection (Section 7.2.1).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
Table 7-3
Operator options and displays in the Parameters tab
Field/Button
Parameter tree
Meaning/Instruction
Tree display of the parameters
The parameters are divided between the individual menus and submenus in
the tree.
Online mode:
In online mode, you can open a context menu by right-clicking the parameter/entry. The following functions are available:
• Read parameter individually
• Write parameter individually
• Reset parameter to factory setting
See Reading parameters / writing parameters / resetting parameters to
factory settings (Section 7.3.4).
Symbols:
•
Write protection – the parameter cannot be edited
The current authorization level does not permit write access to this parameter.
•
Unrestricted access
The current authorization level permits reading, editing and writing of the
parameter
•
Unrestricted access without upload – critical operating parameter
The current authorization level permits reading, editing and writing of the
parameter
To protect such parameters in the device, the parameter must be explicitly
selected and written individually.
See Reading parameters / writing parameters / resetting parameters
to factory settings (Section 7.3.4)
•
Display parameters
Display parameters can only be read and are typically actual values.
To refresh the actual value display, activate the automatic update
•
Parameter table
.
Entry – this is a parameter entry
Tabular display of the parameters
You can edit the parameter values in this view, see Editing parameters
(Section 7.3.3).
Online mode:
In online mode, you can open a context menu by right-clicking the parameter/entry. The following functions are available:
• Read parameter individually
• Write parameter individually
• Reset parameter to factory setting
See Reading parameters / writing parameters / resetting parameters to
factory settings (Section 7.3.4).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-57
Configuration Tool
Table 7-3
Operator options and displays in the Parameters tab
Field/Button
Meaning/Instruction
Number
Unique, three-part parameter number, e.g. 000.005.00012
Parameter
Associated values are grouped under a parameter.
Parameter lists are shown with square brackets after the parameter name,
e.g. "Leap second[20]".
Entry
The individual values of a parameter are each called an entry of a parameter.
Note
Entries can be edited individually, but not read or written individually. The
entire parameter is always read or written with all its entries. If a list is being
considered, the entire list is read or written.
Value
Numeric value or setting of the parameter entry
•
Write protection – the parameter cannot be edited
The current authorization level does not permit write access to this parameter.
•
Unrestricted access
The current authorization level permits reading, editing and writing of the
parameter
•
Unrestricted access without upload – critical operating parameter
The current authorization level permits reading, editing and writing of the
parameter
To protect such parameters in the device, the parameter must be explicitly
selected and written individually. See Reading parameters / writing
parameters / resetting parameters to factory settings (Section 7.3.4).
•
Display parameters
Display parameters can only be read and are typically actual values.
To refresh the actual value display, activate the automatic update
Parameter info
.
Information about the selected parameter
Information about the selected parameter/entry is displayed here.
Note
If the configuration tool is not authorized or operated with a low authorization level,
not all parameters are displayed. This restriction affects, for example, settings
under "System".
The access rights also change with the authorization level.
7-58
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
7.3.1
Sorting the parameter table
To sort the parameter table according to number or parameter:
1. Click the "Number" or "Parameter" column.
−> The table is sorted in alphabetical order according to the clicked column.
2. Click the "Number" or "Parameter" column again to reverse the alphabetical
order.
−> Depending on the current sorting, the alphabetical order is reversed to
either ascending or descending alphabetical order.
The current sorting order is indicated by an arrow next to the column title:
7.3.2
Showing/hiding parameter table entries
To show or hide parameter entries:
1. Click the
symbol at the left side of the table next to the parameter.
−> The parameter entries are shown.
2. Click the
symbol at the left side of the table next to the parameter.
−> The parameter entries are hidden.
Figure 7-4 Parameter table with shown and hidden entry
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-59
Configuration Tool
7.3.3
Editing parameters
Requirement for the editing of a parameter entry
• It must be a writeable entry (
).
To change the value of a parameter entry:
1. Show the values of the desired parameter in the parameter table, see Showing/hiding parameter table entries (Section 7.3.2).
2. Click the "Value" column of the parameter entry.
−> The dialog box to edit the entry is opened.
The input can be aborted with ESC.
Figure 7-5 Example of edit dialog box drop-down list
For parameters with units, you can also enter the new value without unit. Any
units that are entered are ignored, only the numeric value is accepted.
Figure 7-6 Example of edit dialog box numeric entry
Note
In online mode, the value is sent to the device when the input is completed.
7-60
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
To check whether the value has been accepted by the device:
1. In online mode, select the entry of the changed parameter, as described
above.
−> The current value in the device is displayed.
Note
Depending on the parameter/entry and operation status, the device checks
whether the value change has been accepted. If the device rejects the new value,
the old value is reset.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-61
Configuration Tool
7.3.4
Reading parameters / writing parameters / resetting
parameters to factory settings
In online mode, you can individually read, write and reset parameters to their factory settings.
To initiate the "Read parameter", "Write parameter" or "Reset parameter to
factory setting" function:
1. Make sure that the configuration tool is connected to the device. See Establish/disconnect online connection (Section 7.2.1).
2. Select the desired parameter/entry in the parameter tree or parameter table.
3. Right-click the parameter or entry.
−> The context menu opens.
Left-click the desired function.
Figure 7-7 Context menu to read, write or reset parameter
7-62
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
7.4
Archive
You can load archive data from the device and save it as a file as well as evaluate
and search the data with filter functions in the Archive tab of the configuration tool.
Figure 7-8 SICLOCK TC400 configuration tool - archives
(1) Toolbar of the Archive tab
(2) Archive table
(3) Include filter (show events)
(4) Exclude filter (hide events)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-63
Configuration Tool
Table 7-4
Operator options and displays in the Archive tab
Field/Button
Meaning/Instruction
Output of the archive to a text file
Print table to text file
The currently displayed archive table is output to a text file. Events hidden via
the filter are not output. The data can, for example, be further edited with
Excel.
Notice
Archives cannot be restored from these text files. To restore an archive, it
must first have been saved in U600 format.
See Open/Save in General functions (Section 7.2).
Download archive of the connected device
Download archive
(online connection
required)
The archive of the connected device including the description data (e.g. texts
in all languages) is downloaded. This can take several minutes. Implicitly the
parameterization is downloaded again from the device.
Notice
The currently loaded data (parameterization and archive) is overwritten.
See also Establish/disconnect online connection (Section 7.2.1).
Download archive of the connected device without parameter description
Refresh archive
(online connection
required)
The archive of a connected device is downloaded without the description
data. The download without description data is faster than "Download
archive". Implicitly the parameterization is downloaded again from the device.
Notice
The currently loaded data (parameterization and archive) is overwritten.
See also Establish/disconnect online connection (Section 7.2.1).
Display only coming and going events
Collapse view to coming/going
Only persistent messages (typically alarms) are displayed in the archive
table. This provides a compact overview of the important operational faults.
The hidden events are displayed in the exclude window of the filter.
To display all the events again, clear the include filter.
See Filter (Section 7.4.2).
Move event from the include to the exclude filter and vice versa
Change exclude-include
view
The events selected in the include and exclude filters are moved respectively
to the other filter.
See Filter (Section 7.4.2).
Remove all events from the include filter
The events are moved to the exclude filter.
Clear include filter
See Filter (Section 7.4.2).
Remove all events from the exclude filter
The events are moved to the include filter.
Clear exclude filter
7-64
See Filter (Section 7.4.2).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
Table 7-4
Operator options and displays in the Archive tab
Field/Button
Archive table
Meaning/Instruction
Events are displayed in tabular form
Persistent messages trigger a coming and going event and are highlighted in
color:
• red = coming
• green = going
Typically alarms in the device are implemented as persistent messages.
Type
Event type:
• System
• Application
• Information
• Warning
Note:
Each event type is managed in the device in a separate buffer. When a buffer
is full, the next message of this type overwrites the oldest message in the
buffer.
See also Messages (Section 12).
Time
Time when triggered in the device, UTC time base
Event
Message triggered by the device
The sum of all the events forms the archive of the device.
Information
Optional accompanying information to the event
+/-
• ++ (coming)
Event marked as coming (persistent message, e.g. alarm)
• -- (going)
Event marked as going (persistent message, e.g. alarm)
Include filter
Events that are displayed in the archive table
See Filter (Section 7.4.2).
Exclude filter
Events that are not displayed in the archive table
See Filter (Section 7.4.2).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-65
Configuration Tool
7.4.1
Sorting the archive table
To sort the archive table according to time or event:
1. Click the "Time" or "Event" column.
−> The table is sorted in alphabetical order according to the clicked column.
2. Click the "Time" or "Event" column again to reverse the alphabetical order.
−> Depending on the current sorting, the alphabetical order is reversed to
either ascending or descending alphabetical order.
The current sorting order is indicated by an arrow next to the column title:
7-66
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
7.4.2
Filter
You can specifically show and hide events via a filter to facilitate searching in the
archive. All events listed in the include window are displayed in the archive table,
all events listed in the exclude window are not displayed.
Changing the assignment of an event in the filter from include to exclude
(or vice versa):
1. Click the event in the include window (or exclude window).
−> The event is highlighted in blue.
2. Click
.
−> The event is transferred from the include to the exclude filter (or vice versa).
To select and exchange several events in the filters:
1. Press the CTRL while you are selecting the events in the filter per mouse click.
−> The event is highlighted in blue and the already selected events also
remain highlighted in blue.
2. Click
.
−> The event is transferred from the include to the exclude filter (or vice versa).
To select and exchange several successive events in the filters:
1. Click the first element of the event group.
2. Click the last element of the event group while simultaneously pressing the
SHIFT key.
−> The two events and all the events in between are selected.
3. Click
.
−> The event is transferred from the include to the exclude filter (or vice versa).
To remove all events from the include or exclude filter:
1. Click the
button above the include or exclude filter.
−> The include or exclude filter is cleared. The cleared events are now in the
opposite filter for selection.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-67
Configuration Tool
7.5
Troubleshooting
The following is a list of FAQs and problem solutions for the SICLOCK TC400
configuration tool.
Table 7-5
Problem solutions for the configuration tool
Question/Problem
Cause/Remedy
Authorization not possible in offline mode
The data does not contain authorization parameters. You must perform an
online authorization.
See Authorization (Section 7.2.2).
A connection cannot be established to the device
• Check whether the correct IP address has been set in the configuration tool.
• Check whether there is a network connection.
• Check whether the TCP:2155 port has been released for the connection or
already being used by another application.
See also Establish/disconnect online connection (Section 7.2.1).
An event cannot be acknowledged.
This is a persistent message pending on the device.
See also General functions (Section 7.2).
No interaction with the device in online mode (hourglass)
The connection to the device has been separated and must be established
again.
See also Establish/disconnect online connection (Section 7.2.1).
Parameter cannot be edited
• The parameter is a display parameter
See Parameters (Section 7.3)
• The current authorization level is too low
See Authorization (Section 7.2.2)
• The parameter does not have a parameter value
In this case, the parameter must be read from the device again.
Parameters and archives are displayed in a language other than the user interface
The language set in the configuration tool is not available in the device.
See Menus (Section 7.1)
Parameter is not written during the upload
It is a critical operating parameter
that is explicitly excluded from an upload.
Such parameters must be written individually.
See Parameters (Section 7.3) and Reading parameters / writing parameters
/ resetting parameters to factory settings (Section 7.3.4).
7-68
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Configuration Tool
Table 7-5
Problem solutions for the configuration tool
Question/Problem
Cause/Remedy
Parameters are displayed without value
The authorization level has been raised after a download so that higher authorized parameters are now shown. However, no value was supplied for these
parameters in the lower authorized request.
You can refresh these values with the
button or read them individually.
See
Parameters (Section 7.3),
Authorization (Section 7.2.2) and
Reading parameters / writing parameters / resetting parameters to factory
settings (Section 7.3.4).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
7-69
Configuration Tool
7-70
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization and Operation on the Device
8
The SICLOCK TC400 has a 2-line, alphanumeric backlit LCD display and automatic contrast control for the display of date and time, messages and status.
You can change important parameters for the commissioning and acknowledge messages via an
integrated keypad.
.
Figure 8-1 SICLOCK TC400 front view
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
8-71
Parameterization and Operation on the Device
8.1
Operating display
When the device is switched on, there is no operating and status display for a
short ramp-up time.
SICLOCK TC400
......
Figure 8-2 Display of the device ramp-up after switching on
The time, date and the current synchronization status are displayed during operation.
09:48:26
→NTP
Tue, 19. Sept 2007
Figure 8-3 Example of the display during operation
Table 8-1
Possible synchronization states
Display
Meaning
→Q
→NTP
→DCF11)
→DCF21)
→GPS11)
→GPS21)
→MBG1
→MBG2
→NME1
→NME2
→SER1 flashing
→SER2 flashing
No external synchronization
--1 flashing2)
--2 flashing2)
The external synchronization at RADIO CLOCK 1 or RADIO
CLOCK 2 has not supplied a signal for longer than 30 min
(default setting) and there has been no switchover yet to a
substitute synchronization.
External synchronization via NTP is active
External synchronization via DCF signal at RADIO CLOCK 1
or RADIO CLOCK 2 is active
External synchronization via GPS signal at RADIO CLOCK 1
or RADIO CLOCK 2 is active
External synchronization via Meinberg telegram at RADIO
CLOCK 1 or RADIO CLOCK 2 is active
External synchronization via NMEA telegram at RADIO
CLOCK 1 or RADIO CLOCK 2 is active
Currently a valid serial telegram is not being received
1)
If the display is flashing, currently no valid signal is being received.
2)
This is the case when the timeout for the switchover to the substitute synchronization has been selected larger than the monitoring timeout of the external synchronization.
The timeout for the switchover to the substitute synchronization can be set via the
following parameter entry:
/Redundancy/Redundancy/timeout (0.09.10)
The timeout of the external synchronization can be set via the following parameter
entry:
/Inputs/Input 1/Monitoring/timeout (0.20.01) or
/Inputs/Input 2/Monitoring/timeout (0.21.01)
8-72
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization and Operation on the Device
Operating display with pending message
EVENT
event text event text..
´
19/09/2007
10:41:27
event text event text..
Figure 8-4 Example of the display during operation with an error
In the top line, the message type and the date/time are displayed alternately. In
the bottom line, the message text is displayed in scrolled form.
When a message occurs, the backlighting is automatically switched on for 10 minutes.
Table 8-2
Possible message types
Display
Meaning
INFO
Current message is an information message
WARNING
Current message is a warning
EVENT
Other messages, e.g. an alarm
Note
Pending messages can be acknowledged with OK.
If a persistent message that cannot be acknowledged is pending, you can change
to the operating display temporarily with the ESC key.
Backlighting
The display backlighting is switched on for 10 minutes every time a key is pressed
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
8-73
Parameterization and Operation on the Device
8.2
Operation and parameterization
The following figure shows the basic operating sequence on the device. The initial
situation is either the operating display or the message display on the device.
2SHUDWLQJGLVSOD\
ൺ173
7XH6HSW
3DVVZRUGLQSXW
6(783
VHFRU(6&
/LVWRISDUDPHWHUV
3DVVZRUG2.
ൺ/DQJXDJH
(7+,3DGGUHVV
3DVVZRUG
2.
2.RU(6&
(GLWLQJGLDORJER[
/DQJXDJH
*HUPDQ(QJOLVK
VHFRU(6&
VHF
ಹ7KHSDVVZRUGLQSXWLVVNLSSHGLIWKHDXWKRUL]DWLRQKDVDOUHDG\EHHQSHUIRUPHGDQG
LWLVOHVVWKDQVHFRQGVVLQFHWKHODVWNH\ZDVSUHVVHG
0HVVDJH SHUVLVWHQWFXUUHQWO\FDQQRWEHDFNQRZOHGJHG
1HZPHVVDJH
0HVVDJHGLVSOD\
(9(17
HYHQWWH[WHYHQWWH[Wಹ
(6&
VHF
2SHUDWLQJGLVSOD\
ൺ173
7XH6HSW
0HVVDJH LQIRUPDWLRQPHVVDJHRUZDUQLQJ
1HZPHVVDJH
0HVVDJHGLVSOD\
,1)2
HYHQWWH[WHYHQWWH[Wಹ
(6&
2SHUDWLQJGLVSOD\
VHF
ൺ173
7XH6HSW
2.
ൺ173
7XH6HSW
0HVVDJH DFNQRZOHGJHDEOH
1HZPHVVDJH
0HVVDJHGLVSOD\
(9(17
HYHQWWH[WHYHQWWH[Wಹ
2SHUDWLQJGLVSOD\
2SHUDWLQJGLVSOD\
4XLW
ൺ173
7XH6HSW
ಹ7KHPHVVDJHFDQEHDFNQRZOHGJHGIRUH[DPSOHZLWKWKH
FRQILJXUDWLRQWRRORUGLUHFWO\RQWKHGHYLFH(6&ൺ3DVVZRUGLQSXWൺ3DUDPHWHUOLVWൺ
$FNQRZOHGJHHYHQWVൺ$OOHYHQWV
1RWH
$OZD\VDFNQRZOHGJHWKHPHVVDJHVLQGLYLGXDOO\ZLWK2.RUYLDWKHFRQILJXUDWLRQWRRO
7KHIXQFWLRQIRUDFNQRZOHGJLQJDOOPHVVDJHVLVLQWHQGHGIRUH[FHSWLRQDOFLUFXPVWDQFHVVXFKDV
FRPPLVVLRQLQJDQGDFNQRZOHGJHVDOOPHVVDJHVXQFRQGLWLRQDOO\DQGFOHDUVDOOSHQGLQJDODUPV
DQGZDUQLQJV
Figure 8-5 Operating sequence
8-74
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization and Operation on the Device
8.2.1
Authorization (enter password)
A password in the form of a 10-digit decimal number must be entered so that the
operator can make entries on the device.
You can operate the device after successful authorization.
If no entry is made for 30 seconds, the display automatically switches to the operating display and you have to log on again in order to make entries.
To enter the password on the device:
1. Press the SETUP key.
−> The entry dialog box for the password appears.
Password:
0000000000
2. Enter the password with the arrow keys ↑ ↓ ← → and confirm the input with
OK.
− Password was correct
−> the parameter list is displayed. You can operate the device in accordance with your authorization level.
− Display has switched to operating display
−> The password input is automatically cancelled 30 seconds after the last
key is pressed.
Repeat your password input.
− Password was incorrect and is not accepted by the device
−> A message appears that the password has not been accepted.
Repeat the input with a correct password.
The password input can be aborted at any time with ESC.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
8-75
Parameterization and Operation on the Device
8.2.2
Parameter list
The parameter list is displayed after successful authorization, see Authorization
(enter password) (Section 8.2.1).
Table 8-3
Parameter list
Language
ETH1 IP Address
ETH1 IP Subnet
ETH1 IP Gateway
ETH2 IP Address
ETH2 IP Subnet
ETH2 IP Gateway
ETH3 IP Address
ETH3 IP Subnet
ETH3 IP Gateway
ETH4 IP Address
ETH4 IP Subnet
ETH4 IP Gateway
Acknowledge events
Version
Note
The TC400's four Ethernet ports must be on different subnets.
Optionally, the parameters can be set and checked via the configuration tool:
• Language
/Display/View/language (0.10.01)
• Ethernet settings
/Network Settings/Ethernet 1/IP Adapter 1 (0.05.01)
/Network Settings/Ethernet 2/IP Adapter 2 (0.05.02)
/Network Settings/Ethernet 3/IP Adapter 3 (0.05.03)
/Network Settings/Ethernet 4/IP Adapter 4 (0.05.04)
• Version
/Versions/Software Version (0.08.01)
/Versions/Hardware Version (0.08.03)
See also Parameterization (Section 9), Parameter Table (Section 10) and for
acknowledging messages General functions (Section 7.2).
8-76
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization and Operation on the Device
To select a parameter for editing:
1. Navigate with the arrow keys ↑ ↓ to the desired parameter.
−> Depending on which key is pressed, the parameter list is scrolled up or
down in an endless loop.
The currently selected parameter is indicated by the ∀→" sign.
→Language
ETH1 IP Address
2. Switch to the edit mode by pressing OK.
−> The editing dialog box is displayed.
Note
If no entry is made for 30 seconds, the display automatically switches to the operating display and you have to log on again in order to make entries.
8.2.3
Editing dialog box
Language
If you have selected "Language" in the parameter list, the following editing dialog
box appears:
Language:
German English
All texts in the display are shown in the language set here.
To change the language:
1. Select the desired language with the arrow keys ← →.
−> The currently selected language flashes.
2. Accept the selected language with OK.
−> The new setting is accepted and the parameter list is displayed again for
selection.
Ethernet settings
If you have selected an Ethernet setting in the parameter list, the following editing
dialog box appears, e.g. for "ETH3 IP Address":
ETH3 IP Address
192.168.3.30
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
8-77
Parameterization and Operation on the Device
To change the address:
1. Select the decimal place to be changed with the arrow keys ← →.
−> The currently selected decimal place flashes.
2. Select the new number with the arrow keys ← →.
−> The new number flashes.
3. Repeat steps 1) and 2) for all the numbers to be changed.
4. Accept the new address with OK.
−> The new address is accepted and the parameter list is displayed again for
selection.
Acknowledge events
If you have selected "Acknowledge events" in the parameter list, the following
editing dialog box appears:
Acknowledge events:
All events
The "All events" text flashes.
To acknowledge all events:
1. Confirm the acknowledgement of all events with OK.
−> The events are acknowledged and the parameter list is displayed again for
selection.
Note
All messages are acknowledged unconditionally with this function.
Version
If you have selected "Version" in the parameter list, the following dialog box
appears:
Version:
Firmware: 1.0.0014
´
Version:
Processor: 1.0.0005
The display alternates between the firmware and the processor version.
You cannot make any settings in this dialog box. Press ESC or OK to return to the
display of the parameter list.
8-78
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
9
The following is a description of the frequently required settings.
Further information
Parameter Table (Section 10)
Configuration Tool (Section 7)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-79
Parameterization
9.1
Linking the external synchronization
The external synchronizations can be linked via Ethernet as NTP server and/or
as radio clock via point-to-point connections to the SICLOCK TC400.
Prerequisite for operation is at least one external synchronization. Additional
external synchronization can be used as substitute synchronizations if a fault
occurs, see Redundancy (Section 2.6).
External synchronizations can be GPS or DCF77 radio clocks, cabled distribution
systems, atomic clocks or other signal sources.
Further information
Synchronization (Section 9.3.2).
9.1.1
Radio clocks via terminals
Only two radio clocks can be connected at the same time, see also Terminal
assignment (Section 15.1).
Certain redundancy mechanisms enable an automatic switchover to the second
radio clock when a fault occurs, see Redundancy (Section 9.1.3).
Monitoring
The /Inputs/Input 1/Monitoring (0.20.01) parameter for radio clock 1 or the
/Inputs/Input 2/Monitoring (0.21.01) parameter for radio clock 2 can be used to
monitor the input signal of the radio clocks and after expiry of the monitoring time,
an alarm or a warning output.
Status display
See Connecting the external synchronization (Section 6.3).
Serial formats
The /Inputs/Input 1/Framing (0.20.03) parameter displays the automatically
detected framing for serial formats.
There are entries for baud rate, data bits, parity and stop bits.
9-80
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
9.1.2
Operation as NTP client
Four IP addresses of NTP servers can be assigned for SICLOCK TC400 as NTP
client.
The servers are polled regularly and, on the basis of a strict selection strategy, a
preferred server is selected.
For the strategy when a server fails, see Redundancy (Section 2.6).
NTP client
You can activate the client service with the /NTP Client/NTP Client (0.18.01)
parameter.
IP address of the NTP servers
Four IP addresses of the NTP servers can be assigned with the /NTP Client/NTP
Server List[4] (0.18.02) parameter. Address 0.0.0.0 means that no server has
been entered.
DNS names are not supported.
Current NTP server
The /NTP Client/Active Server (0.18.03) parameter displays the currently
selected NTP server. Address 0.0.0.0 means that no server has been entered.
Monitoring the servers
The /NTP Client/Monitoring/monitor server (0.18.04) parameter can be used to
set up the monitoring of the NTP servers.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-81
Parameterization
9.1.3
Redundancy
The preference when an external synchronization fails depends on the setting of
the /Redundancy/Redundancy (0.09.10) parameter:
• "Master (prefer radio clocks to NTP)" setting
− RADIO CLOCK 1 is always accepted.
− RADIO CLOCK 2 is used when RADIO CLOCK 1 is not available.
− NTP is used when RADIO CLOCK 1 and RADIO CLOCK 2 are not available.
• "Slave (prefer NTP to radio clocks)" setting
− RADIO CLOCK 1 is used when NTP is not available.
− RADIO CLOCK 2 is used when NTP and RADIO CLOCK 1 are not available.
− NTP is always accepted.
• The four Ethernet ports must be operated on different subnets to give IP-network redundancy. Configuring more than one Ethernet port for the same subnet is not permitted.
9-82
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
9.2
Linking the time receivers
The following options are available for the linking of the radio receivers:
• Ethernet link via NTP server
• Ethernet link via SIMATIC method
• OUTPUTs 1 to 3 via terminals (direct point-to point-connection to SICLOCK
TC400)
The following section describes the parameterization options:
9.2.1
NTP server service
The NTP server is available on all four Ethernet ports and supports the any/unicast and multicast modes in accordance with RFC2030.
Any/unicast (standard mode)
This mode is used, for example, by PCs and is available globally for all ports.
The parameter entry /NTP Server/NTP Server/operation (0.16.01) = "on" activates the NTP server in any/unicast mode. The setting options "off" and "only if
synchronized" are also possible.
Conditional operation is possible with the setting "only if synchronized". The
server service only functions if the device is externally synchronized.
Multicast
This mode must be set explicitly for each subnet.
You can set multicast mode for up to four subnets with the /NTP Server/Multicast[4]/Multicast[x]/mode (0.16.02) parameter
The parameter entry "Multicast address" specifies the multicast IP address to be
used, e.g. 192.168.2.255".
Setting options for the parameter entry mode:
• off
• 10 s – standard operation, i.e. the coded time does no include time zones
• 60 s – standard operation, i.e. the coded time does no include time zones
• 10 s with local time – for receivers that do not have a calendar
• 60 s with local time – for receivers that do not have a calendar
The parameter entry "Multicast address" specifies the multicast IP address to be
used.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-83
Parameterization
9.2.2
SIMATIC method
The four Ethernet ports support the SIMATIC method with four protocols:
• PCS7-compatible mode
• S5-compatible mode
A parameter is available for each Ethernet port.
• /SIMATIC Method/Ethernet 1 (0.15.01) parameter
• /SIMATIC Method/Ethernet 2 (0.15.02) parameter
• /SIMATIC Method/Ethernet 3 (0.15.03) parameter
• /SIMATIC Method/Ethernet 4 (0.15.04) parameter
Mode
The parameter entry /SIMATIC Method/Ethernet 1/mode (0.15.01) sets the send
clock between 0 s, 1 s and 10 s.
Send condition
The parameter entry /SIMATIC Method/Ethernet 1/send condition (0.15.01) specifies whether the signal should always be output or only if synchronized.
Destination address
The parameter entry /SIMATIC Method/Ethernet 1/destination address (0.15.01)
specifies the send address of the SIMATIC method. Typically the broadcast
address FF:FF:FF:FF:FF:FF is set.
9-84
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
9.2.3
OUTPUT 1 to 3 via terminals
Three parameterizable outputs are available on the terminals:
• /Outputs/Output 1 (0.12.01) parameter as current or voltage signal
• /Outputs/Output 2 (0.13.01) parameter as current or voltage signal
• /Outputs/Output 3 (0.14.01) parameter as RS422 signal
Output signal
The following output signals can be set via the parameter entry "Signal to output":
• DCF77 with local time
• DCF77 with UTC
• Pulse per second
• Pulse per minute
• Serial telegram
See Output telegram (for OUTPUT 1 to 3) (Section 9.2.5).
Inverted
You can invert the signal with the parameter entry "Inverted".
Pretrigger
The parameter entry "Pretrigger" is used to set how many nanoseconds before
the second change the output should switch. With that, line delays can be compensated.
Conditional output
The parameter entry "Conditional output" specifies whether the signal should
always be output or only if synchronized. The required setting for the redundant
configuration of the outputs is described in OUTPUT 1 and 2 redundant
(Section 9.2.4).
Further information
Terminal assignment (Section 15.1)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-85
Parameterization
9.2.4
OUTPUT 1 and 2 redundant
A redundant point-to-point connection can be implemented with two SICLOCK
TC400 devices. Both devices must be synchronous. Typically, this is ensured by
device 2 using device 1 as external synchronization (e.g. device 2 as NTP client
and device 1 as NTP server).
See also Redundancy (Section 2.6) and Redundant point-to-point connections (Section 6.4.2).
The output for OUTPUT 1 or 2 of device 1 is set to "only if synchronized", the output for OUTPUT 1 or 2 of device 2 to "send unconditional".
Example:
OUTPUT 1 of both devices is to be operated redundantly.
Device 1:
Parameter entry /Outputs/Output 1/conditional output (0.12.01) = "only if synchronized"
Device 2:
Parameter entry /Outputs/Output 1/conditional output (0.12.01) = "send unconditional"
Table 9-1
Redundancy response in various situations
Synchronization
Response
Device 1 Device 2
External synchronization
Radio
clock
External synchronization
None
External synchronization
None
Device 1 The time receiver receives the signal from both
devices. The lack of definition is in the µs range and
can be ignored.
Radio
clock
The time receiver receives the signal from device 2.
None
The time receiver receives the signal from device 2.
(Because of the setting "Only if synchronized", device 1
does not supply the time in this case.)
(Because of the setting "Only if synchronized", device 1
does not supply the time in this case.)
External synchronization
Radio
clock
Radio
clock
If the device 1 – device 2 connection is faulted, the time
receiver receives the signal from both devices. There is
a lack of definition in the accuracy of the external synchronization which is usually in the µs range and can
be ignored.
Large inaccuracies can occur when an external synchronization also supplies a faulty signal.
9-86
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
9.2.5
Output telegram (for OUTPUT 1 to 3)
If the output signal is defined as a serial telegram, you can specify the settings for
the data transfer with the /Outputs/Output Telegram (0.19.01) parameter.
Format
The parameter entry /Outputs/Output Telegram/format (0.19.01) offers the following telegram formats for selection:
• Meinberg compatible (including time zones)
• Meinberg compatible (not including time zones)
• NMEA (0183/ZDA)
Baud rate
You can set the following values with the parameter entry /Outputs/Output Telegram/baud rate (0.19.01):
1200 Bd, 2400 Bd, 4800 Bd, 9600 Bd, 19200 Bd, 38400 Bd, 57600 Bd, 115200 Bd
Data width
You can specify the number of data bits with the parameter entry /Outputs/Output
Telegram/data bits (0.19.01):
7 bits or 8 bits
Parity
You can specify the parity with the parameter entry /Outputs/Output Telegram/parity (0.19.01):
none, even, uneven
Stop bits
You can specify the number of stop bits with the parameter entry /Outputs/Output
Telegram/stop bits (0.19.01):
1 bit or 2 bits
Further information
OUTPUT 1 to 3 via terminals (Section 9.2.3)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-87
Parameterization
9.3
General settings on the device
Important general settings are described in the following, e.g. the time adjustment, the synchronization response, etc.
You can find a list of all setting options in Parameter Table (Section 10).
9.3.1
Time management
Note
Only make changes to the plant time at one central location, ideally at the plant
central clock.
Setting the time manually
Optionally, you can set the time in the device via one of the following parameters:
• /Time/Local Time (0.09.04) parameter
• /Time/UTC Time (0.09.02) parameter (universal time)
• /Time/TAI Time (0.09.04) parameter (atomic time)
Time zone
The /Time/Time Zone (0.09.06) parameter is used to specify the offset from UTC
to local zone time without possible daylight saving time.
Note
If the external synchronization already contains a time zone (e.g. DCF77 contains
CE/CEDST), this is already taken into account when received.
If the time zone is not defined by the external synchronization (e.g. serial telegram), no further correction is made for the time zone.
Difference between TAI and UTC
You can read out the difference between atomic time TAI and world time UTC in
seconds with the /Time/Advanced/Atomic Time TAI/Offset From UTC To TAI
(0.09.01) parameter.
9-88
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
Daylight saving time
The daylight saving time changeover is automatically performed by the device at
the parameterized times.
/Time/Advanced/Daylight Saving Time (0.09.07) parameter
Note
The preset changeover times correspond to the present valid regulations of the
European Community.
With the setting "enable = no", the time changeover is suppressed and the plant
is operated with standard time.
The calendrical regulation for the daylight saving time changeover can be specified worldwide via a parameter.
Leap seconds
Use the /Time/Advanced/Leap Seconds[20] (0.09.05) parameter to specify the
calendar of leap seconds.
9.3.2
Synchronization
Synchronization status
You can read out different information about the current synchronization status
via the /Synchronization/Status of Synchronization (0.09.09) parameter.
Protected synchronization
If a discontinuity of more than 5 s occurs in the external synchronization, the protected synchronization is activated. The synchronization is suppressed and an
alarm issued which is present as long as there is a discontinuity in the external
synchronization.
The pending synchronization suppression can be ignored once and the "Protected synchronization" alarm cleared with the parameter entry /Synchronization/Advanced/Protected Synchronization/ignore /clear alarm (0.09.12) = "yes".
Notice
This initiates an unconditional synchronization to the external time and an inconsistency in the time distribution to the plant can result.
If required, disconnect the active external synchronization first or delete the server
address for the NTP client operation from the /NTP Client/NTP Server List[4]
(0.18.02) parameter.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-89
Parameterization
Microstepping
If during operation a difference occurs between the input synchronization (e.g.
radio clock) and the device up to a tolerance of some seconds, that difference will
not be set immediately, since that would cause an inconsistency in the time distribution.
This difference is corrected with microstepping which is significantly below the
time resolution of typical pants and therefore remains unnoticed in the plant operation. This may take up to several hours.
The correction of the time difference with microstepping can be interrupted once
with the parameter entry /Synchronization/Advanced/Microstepping/ignore/cancel (0.09.13) = "yes".
This initiates an immediate synchronization to the external time resulting in an
inconsistency in the time distribution to the plant.
Note
Avoid inconsistencies in the time distribution to the plant.
The Ignore microstepping command is suitable, for example, for the first input
synchronization during the commissioning.
Monitoring
The /Synchronization/Advanced/Monitoring (0.09.14) parameter specifies
whether the device should output an alarm or a warning when there is no external
synchronization.
9.3.3
Display
You can change the language and the display of the time with the /Display/View
(0.10.01) parameter. The time can be displayed as UTC, local time or TAI.
9.3.4
System
You can specify or change the password for the standard protection with the /System/Authorization For Standard Protection (2.06.02) parameter.
You can reset the parameters to the factory settings with the /System/Reset
(0.06.04) parameter. Exceptions are parameters such as network addresses,
authorizations, etc.
9-90
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameterization
9.3.5
Temperature
You activate the monitoring of the module temperatures with the parameter entry
/Environment/Advanced/Temperature/monitoring (0.24.01).
You can set the following values:
• Alarm
• Warning
• No monitoring
The current module temperature is displayed in the parameter entry /Environment/Status/temperature (0.24.02).
9.3.6
Battery
You can specifically disconnect the battery when storing and therefore significantly increase the battery life with the parameter entry /Environment/Advanced/Battery/disconnect (0.25.01).
During power up, the SICLOCK TC400 checks once whether the battery has
been disconnected after at least 30 minutes of operation. If required, the battery
is then automatically connected and a message output.
Notice
If the battery is disconnected, hardware time and archives are lost when the
power supply for the SICLOCK TC400 is switched off.
This command may only be performed by qualified personnel.
See also Battery (Section 11.1).
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
9-91
Parameterization
9-92
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
10
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
Time
Local Time
time and date
UTC Time
time and date
Time Zone
offset from UTC to zone time
0.09.04
0.09.02
0.09.06
Min:
UTC-12:00 h
Max:
UTC+14:00 h
Default:
UTC+01:00 h
Min:
Yes
Max:
No
Default:
Yes
Min:
February, third Sunday, 00:00
Max:
apply a definite date and time
Default:
March, last Sunday, 02:00
Time/Advanced
Daylight Saving Time
enable
0.09.07
time when changing over from
standard time to daylight saving time
Definite Daylight Saving
Time
0.09.08
time when changing back from Min:
daylight saving time to stanMax:
dard time
Default:
February, third Sunday, 00:00
hours
Min:
+1 h
Max:
+2 h
Default:
+1 h
Min:
-1 s
Max:
+1 s
Default:
+0 s
apply a definite date and time
October, last Sunday, 03:00
definite time and date when
changing back from daylight
saving time to standard time
definite time and date when
changing over from standard
time to daylight saving time
Leap Seconds[20]
time and date
0.09.05
size
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
10-93
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
Time/Advanced/Atomic Time TAI
TAI Time
time and date
Offset From UTC To TAI
offset
0.09.03
Min:
-32768 s
Max:
+32767 s
Default:
+0 s
enable
Min:
Yes
(log messages from the TAI
domain in the event log)
Max:
No
Default:
No
Min:
not synchronized (oscillator)
Max:
radio clock 2
Default:
not synchronized (oscillator)
Min:
yes
Max:
no
Default:
no
Min:
-2147483.648 s
Max:
+2147483.647 s
Default:
+0.000 s
0.09.01
TAI Events
0.09.11
Synchronization
Status of Synchronization status
0.09.09
synchronized at least once
last synchronization
current time difference
adjusted drift
input jitter
Min:
-2147483.648 ppm
Max:
+2147483.647 ppm
Default:
+0.000 ppm
Min:
0.000 ms
Max:
4294967.295 ms
Default:
0.000 ms
Min:
yes
Max:
no
Default:
no
Min:
yes
Max:
no
Default:
no
Synchronization/Advanced
Protected Synchronization
ignore / clear alarm
0.09.12
Microstepping
0.09.13
Monitoring
0.09.14
10-94
ignore/cancel
monitor status of synchroniza- Min:
tion
Max:
Default:
off
alarm
off
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
Redundancy
Redundancy
preference
Min:
Max:
Default:
Master
Slave
Master
timeout
Min:
Max:
Default:
10 min
720 min
30 min
IP address
Min:
Max:
Default:
0.0.0.0
255.255.255.255
192.168.1.10
subnet mask
Min:
Max:
Default:
0.0.0.0
255.255.255.255
255.255.255.0
gateway
Min:
Max:
Default:
0.0.0.0
255.255.255.255
0.0.0.0
Network Adapter 1
hardware address
Min:
Max:
Default:
00.00.00.00.00.00
FF.FF.FF.FF.FF.FF
00.00.00.00.00.00
Line State Adapter 1
link
Min:
Max:
Default:
--down
---
linespeed
Min:
Max:
Default:
--100 Mb/s
---
duplex
Min:
Max:
Default:
--half duplex
---
monitor link state
Min:
Max:
Default:
off
alarm
off
IP address
Min:
Max:
Default:
0.0.0.0
255.255.255.255
192.168.2.20
subnet mask
Min:
Max:
Default:
0.0.0.0
255.255.255.255
255.255.255.0
gateway
Min:
Max:
Default:
0.0.0.0
255.255.255.255
0.0.0.0
0.09.10
Network Settings/Ethernet 1
Note: The TC400's four Ethernet ports must be on different subnets.
IP Adapter 1
0.05.01
0.05.05
0.09.13
Advanced Settings
Adapter 1
0.05.09
Network Settings/Ethernet 2
Note: The TC400's four Ethernet ports must be on different subnets.
IP Adapter 2
0.05.02
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
10-95
Parameter Table
Table 10-1
Access1)
/ No.
List of the parameters of SICLOCK TC400
Parameter
Entry
Network Adapter 2
hardware address
0.05.06
Line State Adapter 2
link
0.09.14
linespeed
duplex
Advanced Settings
Adapter 2
monitor link state
0.05.10
Value Range / Default
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
00.00.00.00.00.00
Min:
---
Max:
down
Default:
---
Min:
---
Max:
100 Mb/s
Default:
---
Min:
---
Max:
half duplex
Default:
---
Min:
off
Max:
alarm
Default:
off
Min:
0.0.0.0
Max:
255.255.255.255
Default:
192.168.3.30
Min:
0.0.0.0
Max:
255.255.255.255
Default:
255.255.255.0
Min:
0.0.0.0
Max:
255.255.255.255
Default:
0.0.0.0
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
00.00.00.00.00.00
Min:
---
Max:
down
Default:
---
Min:
---
Max:
100 Mb/s
Default:
---
Min:
---
Max:
half duplex
Default:
---
Network Settings/Ethernet 3
Note: The TC400's four Ethernet ports must be on different subnets.
IP Adapter 3
IP address
0.05.03
subnet mask
gateway
Network Adapter 3
hardware address
0.05.07
Line State Adapter 3
link
0.09.15
linespeed
duplex
Advanced Settings
Adapter 3
0.05.11
10-96
monitor link state
Min:
off
Max:
alarm
Default:
off
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
Network Settings/Ethernet 4
Note: The TC400's four Ethernet ports must be on different subnets.
IP Adapter 4
IP address
0.05.04
subnet mask
gateway
Network Adapter 4
hardware address
0.05.08
Line State Adapter 4
link
0.09.16
linespeed
duplex
Advanced Settings
Adapter 4
monitor link state
0.05.12
Min:
0.0.0.0
Max:
255.255.255.255
Default:
192.168.4.40
Min:
0.0.0.0
Max:
255.255.255.255
Default:
255.255.255.0
Min:
0.0.0.0
Max:
255.255.255.255
Default:
0.0.0.0
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
00.00.00.00.00.00
Min:
---
Max:
down
Default:
---
Min:
---
Max:
100 Mb/s
Default:
---
Min:
---
Max:
half duplex
Default:
---
Min:
off
Max:
alarm
Default:
off
Min:
off
Max:
S5-compat., every 10 s
Default:
off
Min:
---
Max:
only if synchronized
Default:
---
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
FF.FF.FF.FF.FF.FF
SIMATIC Method
Ethernet 1
mode
0.15.01
send condition
destination address
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
10-97
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Ethernet 2
Entry
mode
0.15.02
send condition
destination address
Ethernet 3
mode
0.15.03
send condition
destination address
Ethernet 4
mode
0.15.04
send condition
destination address
Value Range / Default
Min:
off
Max:
S5-compat., every 10 s
Default:
off
Min:
---
Max:
only if synchronized
Default:
---
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
FF.FF.FF.FF.FF.FF
Min:
off
Max:
S5-compat., every 10 s
Default:
off
Min:
---
Max:
only if synchronized
Default:
---
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
FF.FF.FF.FF.FF.FF
Min:
off
Max:
S5-compat., every 10 s
Default:
off
Min:
---
Max:
only if synchronized
Default:
---
Min:
00.00.00.00.00.00
Max:
FF.FF.FF.FF.FF.FF
Default:
FF.FF.FF.FF.FF.FF
Min:
on
Max:
only if synchronized
Default:
on
Min:
off
Max:
60 s with local time
Default:
off
NTP Server
NTP Server
operation
0.16.01
Multicast[4]
mode
0.16.02
multicast address
10-98
Min:
0.0.0.0
Max:
255.255.255.255
Default:
0.0.0.0
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
NTP Client
NTP Client
operation
0.18.01
NTP Server List[4]
IP address
0.18.02
Active Server
IP address
0.18.03
Monitoring
monitor server
0.18.04
Min:
off
Max:
on
Default:
off
Min:
0.0.0.0
Max:
255.255.255.255
Default:
0.0.0.0
Min:
0.0.0.0
Max:
255.255.255.255
Default:
0.0.0.0
Min:
off
Max:
alarm
Default:
off
Min:
no signal
Max:
telegram (faulty)
Default:
no signal
Inputs/Input 1
Status
signal
0.20.02
Monitoring
monitor input
0.20.01
timeout
Framing
baud rate
0.20.03
data bits
parity
stop bits
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Min:
off
Max:
alarm
Default:
alarm
Min:
5 min
Max:
1440 min
Default:
30 min
Min:
0 Bd
Max:
4294967295 Bd
Default:
0 Bd
Min:
0
Max:
8
Default:
0
Min:
none
Max:
odd
Default:
none
Min:
0
Max:
2
Default:
0
10-99
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
Inputs/Input 2
Status
signal
0.21.02
Monitoring
monitor input
0.21.01
timeout
Framing
baud rate
0.21.03
data bits
parity
stop bits
Min:
no signal
Max:
telegram (faulty)
Default:
no signal
Min:
off
Max:
alarm
Default:
off
Min:
5 min
Max:
1440 min
Default:
30 min
Min:
0 Bd
Max:
4294967295 Bd
Default:
0 Bd
Min:
0
Max:
8
Default:
0
Min:
none
Max:
odd
Default:
none
Min:
0
Max:
2
Default:
0
Min:
off
Max:
serial telegram
Default:
off
Min:
no
Max:
yes
Default:
no
Min:
0 ns
Max:
1000000 ns
Default:
0 ns
Min:
send unconditional
Max:
only if synchronized
Default:
send unconditional
Outputs
Output 1
signal to output
0.12.01
inverted
pretrigger
conditional output
10-100
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameter Table
Table 10-1
Access1)
/ No.
List of the parameters of SICLOCK TC400
Parameter
Output 2
Entry
signal to output
0.13.01
inverted
pretrigger
conditional output
Output 3
signal to output
0.14.01
inverted
pretrigger
conditional output
Output Telegram
format
0.19.01
baud rate
data bits
parity
stop bits
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Value Range / Default
Min:
off
Max:
serial telegram
Default:
off
Min:
no
Max:
yes
Default:
no
Min:
0 ns
Max:
1000000 ns
Default:
0 ns
Min:
send unconditional
Max:
only if synchronized
Default:
send unconditional
Min:
off
Max:
serial telegram
Default:
off
Min:
no
Max:
yes
Default:
no
Min:
0 ns
Max:
1000000 ns
Default:
0 ns
Min:
send unconditional
Max:
only if synchronized
Default:
send unconditional
Min:
no output
Max:
NMEA (1083/ZDA)
Default:
no output
Min:
1200 Bd
Max:
115200 Bd
Default:
9600 Bd
Min:
7
Max:
8
Default:
8
Min:
none
Max:
odd
Default:
none
Min:
1
Max:
2
Default:
1
10-101
Parameter Table
Table 10-1
List of the parameters of SICLOCK TC400
Access1)
/ No.
Parameter
Entry
Value Range / Default
Display
View
language
0.10.01
time
Min:
German
Max:
English
Default:
German
Min:
local time
Max:
atomic time TAI
Default:
local time
Min:
0
Max:
4294967295
Default:
2222
Min:
yes
Max:
no
Default:
no
Min:
-10° C
Max:
+125° C
Default:
+ 25° C
Min:
no monitoring
Max:
alarm
Default:
no monitoring
Min:
no
Max:
yes
Default:
No
Min:
0
Max:
4294967295
Default:
0
Min:
0.0.0
Max:
65535.65535.65535
Default:
0.0.0
Min:
0
Max:
4294967295
Default:
0
Min:
0.0.0
Max:
65535.65535.65535
Default:
0.0.0
System
Authorization For Standard Protection
authorization
2.06.01
Reset
factory settings
0.6.04
Environment
Status
temperature
0.24.02
Environment/Advanced
Temperature
monitoring
0.24.01
Battery
disconnect
0.25.01
Versions
Firmware Version
A2B number
0.08.01
version number
Processor Version
A2B number
0.08.02
version number
10-102
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Parameter Table
Table 10-1
Access1)
/ No.
List of the parameters of SICLOCK TC400
Parameter
Hardware Version
Entry
A2B number
0.08.03
release number
Value Range / Default
Min:
0
Max:
4294967295
Default:
0
Min:
0
Max:
65535
Default:
0
serial number
1)
The access symbols display the access possibility at the highest authorization level.
Note
If the configuration tool is not authorized or operated with a low authorization level,
then not all parameters are displayed. This restriction affects, for example, settings under "System".
The access rights also change with the authorization level.
Further information
List of Symbols (Section C)
Authorization (Section 7.2.2)
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
10-103
Parameter Table
10-104
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Service and Maintenance
11.1
11
Battery
An integrated battery supplies the clock block and the archive memory during
phases without power.
The battery can be specifically disconnected for storage which significantly
increases the battery life.
During power up, the SICLOCK TC400 checks once whether the battery has
been disconnected after at least 30 minutes of operation. If required, the battery
is then automatically connected and a message output.
Service life of a disconnected battery during storage: > 12 years
Service life of a connected battery during storage: Approximately 6 years
Notice
If the battery is disconnected, hardware time and archives are lost when the
power supply for the SICLOCK TC400 is switched off.
Note
The battery may only be replaced by the Siemens factory.
Please contact the Product Support.
See also Battery (Section 9.3.6).
11.2
Restoring the factory settings
Restoring individual parameters
Reading parameters / writing parameters / resetting parameters to factory
settings (Section 7.3.4)
Restoring parameters
You can reset the parameters to the factory settings with the /System/Reset
(0.06.04) parameter. Exceptions are parameters such as network addresses,
authorizations, etc.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
11-105
Service and Maintenance
11.3
Software update
You can obtain information and any software updates for your SICLOCK TC400
from the Product Support.
See also Preface.
11-106
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Messages
12
The messages are divided into four different event types:
• System (capacity for approx. 1500 entries)
• Application (capacity for approx. 4500 entries)
• Information (capacity for approx. 21500 entries)
• Warning (capacity for approx. 3000 entries)
Messages for which a going event is also triggered, are called persistent messages. Persistent messages are, for example, alarms.
Note
Each event type is managed in the device in a separate buffer. When a buffer is
full, the next message of this type overwrites the oldest message in the buffer.
The buffer for information is sufficient for approx. 45 days of operation. This is an
average empirical value. Depending on the operating conditions and plant configuration, the number of messages can differ from this value.
For further information, see also Archive (Section 7.4).
Table 12-1
Message overview with event type and brief description
Recording of an input synchronization
Information
The recording of an input synchronization is pending as the threshold value has been
exceeded.
Battery has been disconnected
Application
A user has disconnected the battery for storage via the configuration tool.
See also Battery (Section 9.3.6).
Battery has been connected automatically
Application
The battery has been connected automatically after a minimum period of operation
See also Battery (Section 9.3.6).
Bootloader has been updated
System and
information
The bootloader has been successfully installed.
Bootloader has NOT been updated
System and
information
The bootloader could not be installed.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
12-107
Messages
Table 12-1
Message overview with event type and brief description
Default processor loaded
Warning
The default processor has been loaded when starting
Input 1, 2: DCF77 OK
Information
Correct DCF reception has been detected again after a fault.
Input 1, 2: DCF77 signal faulty
Information
A fault has been detected in the DCF77 signal during stable reception.
Input 1, 2: GPS OK
Information
Correct GPS reception has been detected again after a fault.
Input 1, 2: GPS signal faulty
Information
A fault has been detected in the GPS signal during stable reception.
Input 1, 2: signal timeout
Application
(alarm)
A signal has not been received within the parameterized timeout during activated monitoring.
Check the status display, see Radio clocks via terminals (Section 9.1.1). If "no signal" is displayed in the status, check the wiring.
Input 1, 2: telegram OK
Information
A serial format has been detected (for the first time after a failure).
Input 1, 2: telegram cannot be decoded
Information
The serial format cannot be decoded.
Firmware has been updated
System and
information
A firmware update has been performed and the firmware has been updated.
Firmware has NOT been updated
System and
information
A firmware update has been performed, but the firmware could not be updated.
Flash file system has been formatted
System
The file system has been formatted.
Protected Synchronization
Application
(alarm)
The protected synchronization has been activated as a discontinuity has been detected
in the external synchronization.
The message indicates an error of the external synchronization. See also Synchronization (Section 9.3.2).
Internal error, please contact the support
System
The exact specification of the error is contained in the message text and may be of
importance for the support (hotline).
Processor has been updated
System and
information
12-108
A processor update has been performed and the processor has been updated.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Messages
Table 12-1
Message overview with event type and brief description
Processor has not been updated
System and
information
A processor update has been performed, but the processor could not be updated.
Hardware time set
Information
The SICLOCK TC400 internal hardware clock has been set.
No useable NTP server
Information
A preferred server has not been found.
No hardware time
Application
A valid time could not be read from the hardware.
Critical temperature exceeded
Application
The critical module temperature has been exceeded
See also Temperature (Section 9.3.5).
Link down EHT1, Link down EHT2, Link down EHT3, Link down EHT4
Application
The monitoring of the link status has determined the "Link down" status.
The tripping of an archive entry or alarm can be set, for example, for Ethernet 1 via the
following parameter:
/Network Settings/Ethernet 1/Advanced Settings Adapter 1/monitor link state
(0.05.09)
Microstepping ignored
Application
A microstepping has been avoided once by the user.
See also Synchronization (Section 9.3.2).
NTP server selected
Information
An NTP server has been selected.
NTP server unreachable
Information
The server is no longer available.
Parameter has been reset to factory setting by HMI
Information
A parameter has been reset to the factory setting by the HMI. The parameter number is
specified in the message text.
Parameter has been written by HMI
Information
A parameter has been written by the HMI. The parameter number is specified in the
message text.
Sector in parameter memory cleared
System
An automatic data clearance has been performed in the parameter memory.
Stabilized synchronization
Information
New stabilizer data is available and is displayed in the message.
Synchronization inconsistent
Information
The consistency check of an external synchronization was negative. The external synchronization and the negatively checked offset are displayed.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
12-109
Messages
Table 12-1
Message overview with event type and brief description
Density of synchronization
Information
Specifies the number of input synchronizations per interval.
The message is output cyclically and is used to judge the reception quality.
Synchronization status
Information
The message is output cyclically (e.g. every 12 hours) in order to document the current
external synchronization in the archive.
Status of synchronization (changeover)
Information
The synchronization status has changed.
System start
System
The system has been started. The message is triggered when the system starts.
TFTP file requested
Information
A TFTP file has been requested.
(E.g. firmware update, Web data update, etc.)
TFTP file received
Information
A file has been loaded via TFTP.
(E.g. firmware update, Web data update, etc.)
TFTP file transferred
Information
A file has been transferred from the device via TFTP.
(E.g. firmware update, Web data update, etc.)
Time initialized by hardware
Application
An initial synchronization of the clock module has been performed.
Time set by HMI
Application
12-110
Time domain(s) has(have) been changed via HMI
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
13
Technical Data
Table 13-1
Technical data of the SICLOCK TC400
Dimensions
180.0 x 88.9 x 47.0 (WxHxD in mm)
Weight
Approximately 750 g
Supply voltage
24 VDC (-15% to +20%) at X1
Power supply
Continuous current max. 0.7 A
Transient voltage interruption
Max. 3 ms (at 20.4 V to 28.8 V)
Power consumption
Max. 15 W
Power loss
Typ. 7.5 W
Fuse (external)
1 A time-lag
Degree of protection
IP 20
Mounting type
35 mm DIN rail
DIN rail EN 50022-35 (15 mm high) or SIMATIC standard mounting rail
Safety
Product standard
EN 61131-2 (environment)
Test voltage
Circuits with nominal voltage Ue <50 V relative to other circuits or
ground, test voltage 500 VDC
Protection class
Protection class III according to EN 60536
Electrical safety
EN 60950-1
Time properties
Accuracy with regard to the
GPS signal
< 50 µs
Accuracy with regard to the
DCF77 signal
< 1000 µs
Accuracy if GPS signal fails
< 50x10-9
Accuracy if DCF77 signal fails
< 1x10-6
Accuracy if power supply fails
< 4x10-6
Time correction through microstepping
< 50 µs/s
Jitter during GPS operation
< 200 ns/s
Reserve power
See battery
Battery
Service life during operation
> 12 years
Service life during storage, disconnected
> 12 years
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
13-111
Technical Data
Table 13-1
Technical data of the SICLOCK TC400
Service life during storage, con- < 6 years, see Battery (Section 11.1)
nected
Electromagnetic compatibility (EMC)
Interference emission
EN 55022 Class A, FCC Class A
Immunity to interference
EN 55024
Environmental properties
During operation
EN 60721-3-3 (weather-protected stationary use) Class 3K3
During storage/transport
EN 60721-3-2 Class 2K4
Climatic conditions
Temperature during operation
0° C to 55° C
Temperature during storage/transport
-40° C to 70° C
Temperature gradient
Max. 10° C/h during operation, 20° C/h during storage, no condensation
Relative humidity
Tested to IEC 60068-2-78, IEC 60068-2-30
- during operation
10% to 95% at 25° C (no condensation)
- storage/transport
10% to 95% at 25° C (no condensation)
Atmospheric pressure
1080 to 795 hPa (corresponds to an altitude of -1000 to 2000 m)
Mech. ambient conditions
During operation
EN 60721-3-3, Class 3M3
During storage/transport
EN 60721-3-2, Class 2M2
Interfaces (see also Connecting (Section 6))
Ethernet connection
Four separate Ethernet ports 10/100 MBit/s, autonegotiation
14-pin terminal strip (see also Terminal assignment (Section 15.1))
2x radio clock inputs
(short-circuit proof)
Rated current 20 mA to 40 mA, supply voltage 48 V for the connection of
SICLOCK GPS1000, SICLOCK GPSDEC or SICLOCK DCFRS
Radio clock interfaces are isolated from the remaining electronics.
2x outputs
24 V voltage interface /
20 mA current interface
20 mA / 24 V for DCF77, pulses, cycle clocks, telegrams
The outputs are isolated from the remaining electronics.
(short-circuit proof)
1x RS422 / 5 V output
For DCF77, pulses, cycle clocks, telegrams
1x NC relay output for WARNING signal
Max. 0.06 A, 48 VDC
1x NC relay output for ALARM
signal
Max. 0.06 A, 48 VDC
13-112
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Technical Data
Table 13-1
Technical data of the SICLOCK TC400
Status displays on the device
Display
LEDs
2-line, alphanumeric backlit LCD display and temperature-compensated
contrast control
4x orange LEDs for Ethernet port link-up
4x green LEDs for Ethernet port activity
2x green LEDs for radio clock status
3x green LEDs for output
1x green LED for POWER
1x green LED for SYNC status
1x red LED for FAULT status
Operator controls on the device
Keys
1x SETUP key
4x CURSOR keys
1x ESC key
1x OK key
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
13-113
Technical Data
13-114
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Dimension Drawing
14
Figure 14-1 Dimension drawing
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
14-115
Dimension Drawing
14-116
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
15
Circuit Diagrams
15.1
Terminal assignment
TTY (active)
1
2
24 V / 20 mA
3
4
X2
OUTPUT 1 GND
OUTPUT 1
1
OUTPUT 2
3
OUTPUT 2 GND
4
OUTPUT 3A
OUTPUT 3B
5
RADIO CLOCK GND
RADIO CLOCK 1A
7
RS422
5
A
6
B
2
7
6
8
48 V
8
RADIO CLOCK 1B
RADIO CLOCK 2A
RADIO CLOCK 2B
10
COMMON
12
ALARM OUT
WARNING OUT
13
9
passive
Radio Clock 1
9
11
10
48 V
11
passive
Radio Clock 2
7
14
8
active
Radio Clock 1
48 V
9
10
active
Radio Clock 2
48 V
11
12
13
14
Figure 15-1 Terminal assignment of the SICLOCK TC400
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
15-117
Circuit Diagrams
15-118
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Spare Parts / Accessories
Table 16-1
16
Spare parts and accessories with order numbers
Order number
Single device
SICLOCK TC400 single device
2XV9450-2AR01
Packages
SICLOCK TC400 standard package, contains GPS1000
2XV9450-2AR10
SICLOCK TC400 DCF77
2XV9450-2AR20
Spare parts for GPS1000
GPS1000
E10433-E9910-H100
Mounting frame for GPS1000
2XV9450-1AR03
Lightning protection module for GPS1000
2XV9450-1AR83
DCF77
Active DCF77 antenna with TTY interface
2XV9450-1AR16
Mounting frame for antenna
2XV9450-1AR03
Signal distribution / accessories
Products for the time distribution, such as electrical-optical pulse converter as well as
further accessories can be found at http://www.siemens.com/siclock.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
16-119
Spare Parts / Accessories
16-120
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
A
Appendix
A.1
Directives and declarations
Notes on CE marking
The following applies for the product described in this documentation:
EMC directive
The devices fulfill the requirements for the EC directive ™89/336/EEC Electromagnetic Compatibility™, and are designed for the following fields of application
corresponding to the CE marking:
Table A-1
Fields of application
Field of application
Industrial applications
Requirement for
Interference emission
Immunity to interference
EN 61000-6-4: 2001
EN 61000-6-2: 2001
Declaration of conformity
The EC declaration of conformity and the corresponding documentation are made
available to authorities in accordance with the EC directives stated above. Your
sales representative can provide these on request.
Observing installation guidelines
The installation guidelines and safety instructions in this documentation must be
followed during commissioning and operation.
Connection of I/O devices
The requirements regarding noise immunity according to EN 61000-6-2:2001 are
met when you connect an I/O device suitable for an industrial environment. I/O
devices may only be connected via shielded cables.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
A-121
Appendix
A.2
Certificates and approvals
DIN ISO 9001 certificate
The quality assurance system for the entire product process (development, production, and marketing) at Siemens fulfills the requirements of DIN EN ISO 9001.
This has been certified by DQS (the German society for the certification of quality
management systems).
Note
The approval or approbation is located on the type plate.
EMC
Table A-2
EMC Directives USA
USA
General
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1 This device may not cause harmful interferences.
2 This device must accept any interference received, including interference that may cause undesired operation.
Shielded Cables
The use of shielded I/O cables is required when connecting this
equipment to any and all optional peripheral or host devices. Failure
to do so may violate FCC rules.
Modifications
Siemens AG is not responsible for any radio television interference
caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other
than those specified by Siemens AG. The correction of interference
caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
Canadian Notice
A-122
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformé à la norme
NMB-003 du Canada.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
ESD Guidelines
B.1
B
Electrostatic sensitive devices
Definition
All electronic modules are equipped with large-scale integrated ICs or components. Because of the technology used, these electronic components are very
sensitive to overvoltages and thus to discharge of static electricity.
The acronym ESD has become the established designation for such Electrostatic
Sensitive Devices. This is also the international abbreviation for such devices.
Electrostatic sensitive devices are identified by the following symbol:
Figure B-1 Electrostatic sensitive devices
Caution
Electrostatic sensitive devices can be irreparably damaged by voltages that are
far lower than anything a person can perceive. These voltages occur if you touch
a component or the electrical connection of a module without having previously
discharged any static from your body. Any damage that occurs to a module as a
result of overvoltage is generally not recognized immediately and only comes to
light after the equipment has been operating for some time.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
B-123
ESD Guidelines
B.2
Electrostatic charging of persons
Charging
Anyone who is not conductively connected to the electrical potential of their environment can accumulate an electrostatic charge.
The figure below shows the maximum electrostatic voltages that can accumulate
on a person who is operating equipment when he/she comes into contact with the
materials indicated. These values comply with the specifications in IEC 801-2.
9ROWDJHLQN9
N9
6\QWKHWLFPDWHULDO
:RRO
$QWLVWDWLFPDWHULDO
VXFKDVZRRGRUFRQFUHWH
5HODWLYHDLUKXPLGLW\LQ
Figure B-2 Electrostatic voltage that can accumulate on operating personnel
B-124
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
ESD Guidelines
B.3
Basic measures to protect against the
discharge of static electricity
Ensure sufficient grounding
When working with electrostatic sensitive devices, make sure that the you, your
workstation, and the packaging are properly grounded. This prevents the accumulation of static electricity.
Avoid direct contact
You should only touch ESD components if this is unavoidable (for example, during maintenance work). Handle the modules without touching any chip pins or
PCB traces. If you follow these instructions, electrostatic discharge cannot reach
or damage sensitive components.
If you have to take measurements on a module, make sure that you first discharge
any static that may have accumulated in your body. To do this, touch a grounded
metal object. Only use grounded measuring instruments.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
B-125
ESD Guidelines
B-126
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
C
List of Symbols
Table C-1
Symbol
Meaning
Toolbar of the configuration tools (see also General functions (Section 7.2))
Open
Load a parameterization/archive from the local file system
Save
Save of a parameterization/archive to the local file system
Connect to device
Disconnect from device
Authorize
Acknowledge event
Acknowledge all events
Ignore event
Discard the pending event
Parameters tab (see also Parameters (Section 7.3))
Print table to text file
Download parameters
Download parameters of the connected device
Refresh parameters
Download parameters of the connected device without parameter description
Upload parameters
Transfer writeable values of the loaded parameters to the connected
device
Monitor actual values
Refresh actual value display
Write protection
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
C-127
List of Symbols
Table C-1
Symbol
Meaning
Unrestricted access
Unrestricted access without upload
critical operating parameter
Display parameters
Entry
This refers to a parameter entry
Archive tab (see also Archive (Section 7.4))
Print table to text file
Download archive
Download archive of the connected device
Refresh archive
Download archive of the connected device without parameter description
Collapse view to coming/going
Display only coming and going events
Change exclude-include view
Move event from the include to the exclude filter and vice versa
Clear include filter / Clear exclude filter
Remove all events from the include/exclude filter
C-128
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Glossary
D
Alarm
Alarms are events with coming and going status.
See Persistent message.
Plant central clock
The plant central clock is the central component for the time synchronization of
plants. It synchronizes all time components of the plant via its interfaces.
Plant components, automation units, computers
Plant components is the general term for the devices that have to be synchronized. Depending on the degree of detail they can also be called automation units
or computers.
Typical networked plant components are, for example, PCs, SIMATIC S7.
Typical non-networked plant components are, for example, protective relays, fault
recorders.
Archive
The archive contains relevant events with additional information from the device.
Searches can be performed for specific events in the archive with a filter.
See Filter.
Atomic time (TAI)
The atomic time is defined in standards of some protocols (PTP, PTCP) as time
domains. A calendar of leap seconds is required for the calculation of the atomic
time.
Authorization
In order to be able to change parameter entries in the device using the configuration tool, the user must log on to the configuration tool with a password. There are
various authorization levels.
The current authorization status is displayed in the password entry field in different colors; red is the lowest authorization level.
See Password.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
D-129
Glossary
Persistent message
Persistent messages are events that have a coming and going status, e.g.
alarms.
See Event.
Entry
An entry contains a value or a selection (combo box). Depending on the entry
type, the value/selection can be changed by the user.
Related entries are grouped into a parameter.
See Parameter.
Event
An event is triggered by the device and displays a message or a state of the
device.
See Persistent message.
Event type
Events are classified in various types:
• System
• Application
• Information
• Warning
External synchronization
External time source that is used for the synchronization of the SICLOCK TC400.
Filter
Searches can be performed for specific events in the archive with an include and
exclude filter.
See Archive.
Radio clock
All SICLOCK products that receive the time via an antenna are called radio
clocks. The SICLOCK products SICLOCK DCFRS, SICLOCK GPSDEC,
SICLOCK GPS1000 and packages contain radio clocks. The received radio signal can be preset for more exact delimitation:
• GPS radio clock for GPS and
• DCF radio clock for DCF77
D-130
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Glossary
Device
The SICLOCK TC400 plant central clock is described as a device.
Pulse converter
All products of the SICLOCK range that convert physical levels without changing
the information are designated as pulse converters.
Examples of pulse converters:
SICLOCK EOPC, SICLOCK PCON, SICLOCK DCFHF, SICLOCK DCFS7 interface.
Local area network (LAN)
A local area network describes the networking of different components for a common data exchange.
Non-networked plant equipment
Non-networked plant equipment describes all those plant components that are
not time-synchronized via the local area network, but via point-to-point connections.
See Point-to-point connection.
NTP - Network Time Protocol
Standard for the synchronization in computer systems via packet-based communication networks.
Offline mode
There is no connection between the configuration tool and the device.
The current status is displayed in the IP address entry field in different colors; in
online mode, the IP address is green.
Online mode
There is a connection between the configuration tool and the device.
The current status is displayed in the IP address entry field in different colors; in
online mode, the IP address is green.
Parameter
Related values/settings are combined into a parameter. A parameter contains
one or more entries.
See Entry.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
D-131
Glossary
Password
Authorization may be required for access to parameters. Passwords for various
authorization levels can be defined with the configuration tool.
Initial password on the device: "2222"
See Authorization.
Point-to-point connection
A point-to-point connection describes the synchronization of exactly one non-networked plant component via a dedicated cable, e.g. one output of a plant central
clock.
See Non-networked plant equipment.
SICLOCK DCFRS
Industrial version of the SICLOCK DCFRS radio clock with integrated DCF77
receiver.
SICLOCK GPS1000
Radio clock as GPS receiver
SICLOCK GPSDEC
GPS complete package with SICLOCK GPSDEC decoder.
SICLOCK TC400 configuration tool
Web interface for the parameterization and searching in the archive of a
SICLOCK TC400 device via an Internet browser.
u600 file
The configuration tool can open and save parameters and archives in the form of
*.u600 files.
UTC
UTC stands for Universal Time Coordinated. It is a combination of the international atomic time TAI and the universal time UT. Time zones are specified as a
positive or negative difference to UTC.
TAI
See Atomic time (TAI).
D-132
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Glossary
Volatile parameters
Volatile parameters are parameters containing values/states that continuously
change during operation.
Time synchronization
The time of all plant components, automation units and computers is adjusted
exactly to the reference time of the plant central clock via time synchronization.
Time synchronization of plants
The term Time synchronization of plants is always used to describe when several
components of a plant are synchronized with products of the SICLOCK range.
Zone time
The zone time is the zone time derived from UTC.
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
D-133
Glossary
D-134
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Index
A
N
Actual values, 7-56
Alarm output, 6-46
Atomic time, 9-88
Authorization, 7-54
Authorization on the device, 8-75
NTP client, 9-81
NTP server, 9-83
O
Backlighting, 8-73
Battery, 9-91, 11-105
Offline mode, 7-54
Online connection, 7-53
Online mode, 7-54
Operating display, 8-72
Output telegram, 9-87
C
P
Configuration tool, 7-47
Parameter table, 10-93
Parameters, 10-93
Password, 7-54, 9-90
Passwort, 7-54
Point-to-point connection, 6-43
Power supply, 6-36
Protected synchronization, 2-18,
9-89
Protective measures
Static electricity, B-125
B
D
Daylight saving time, 9-89
Device operation, 8-74
DIN rail, 5-33
Display, 9-90
Display backlighting, 8-73
E
Electrostatic charging of persons,
B-124
Electrostatic sensitive devices, B-123
ESD guidelines, B-123
Event types, 12-107
External synchronization, 9-80
F
Factory setting, 9-90
Filter, 7-67
I
Inconsistency in time in plant operation, 9-89
IP address, 7-53
L
Leap seconds, 9-89
Local time, 9-88
M
Messages, 12-107
Microstepping, 9-90
Mounting position, 4-32
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
R
Radio clocks, 9-80
Ramp-up, 8-72
Redundancy, 2-19
RS422, 6-43
S
Safety information, 1-9
Scope of delivery, 3-25
SICLOCK DCFRS, 6-40
SICLOCK GPS1000, 6-39
SICLOCK GPSDEC, 6-41
SICLOCK TC400 configuration tool,
7-47
SIMATIC method, 9-84
Standard mounting rail, 5-33
Status of synchronization, 8-72
Symbols, C-127
Synchronization, 9-89
T
TAI time, 9-88
Terminal assignment, 15-117
Index-135
Index
Time receivers, 9-83
Time zone, 9-88
TTY, 6-43
U
u600 file, 7-49
UTC time, 9-88
W
Warning output, 6-46
Warnings, 12-107
■
Index-136
© Siemens AG 2007 All Rights Reserved
SICLOCK® TC400
Siemens AG
Industry Sector
Postfach 48 48
90026 N85(0%(5*
*(50$1<
www.siemens.com/siclock