Yamaha T-D500 Owner`s manual

A
Tuner
OWNER’S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place –
away from direct sunlight, heat sources, vibration, dust,
moisture, and/or cold. For proper ventilation, allow the
following minimum clearances.
Top : 10 cm (4 in)
Rear: 10 cm (4 in)
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
i En
18 Before moving this unit, press A to set this unit to the standby
mode, and disconnect the AC power plug from the wall outlet.
19 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave this unit alone.
20 The batteries shall not be exposed to excessive heat such as
sunshine, fire, or the like. When you dispose of batteries,
follow your regional regulations.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you set this unit to standby mode by A. In this state,
this unit is designed to consume a very small quantity
of power.
CONTENTS
ADDITIONAL INFORMATION
REMOTE CONTROL AND FRONT PANEL .... 2
CONNECTIONS .................................................... 4
TROUBLESHOOTING .......................................14
SPECIFICATIONS...............................................16
OPERATIONS
PREPARATION
PREPARATION
DAB TUNING......................................................... 5
OPERATIONS
Preparing the DAB tuning ......................................... 5
Manual tuning............................................................ 6
Presetting DAB stations............................................. 7
Using the DAB functions........................................... 8
DAB station information ......................................... 10
DAB frequency information .................................... 10
FM/AM TUNING ................................................. 11
Automatic and manual tuning.................................. 11
Presetting stations .................................................... 12
Using the FM/AM functions.................................... 13
ADDITIONAL
INFORMATION
■ Features
DAB (Digital Audio Broadcasting) /DAB+ tuner
Sophisticated FM/AM tuner
◆ Automatic scanning function to locate all DAB stations in your
area
◆ DLS (Dynamic Label Segment) information display
◆ Tuning aid function to optimize DAB reception
◆ 40 DAB/DAB+ station preset tuning
◆ Coaxial and optical digital audio output capability for DAB
audio signals
◆ 30-station (each band) FM/AM preset tuning
◆ Automatic preset tuning
■ Supplied accessories
Please check that you have received all of the following parts.
Remote control
Indoor FM antenna
Battery (CR2025)
RCA stereo cable
AM loop antenna
Indoor DAB antenna
■ About this manual
• y indicates a tip for your operation.
• This manual describes how to operate this unit using a remote control except when it is not available. Some of these
operations are also available using the front panel.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
1 En
PREPARATION
REMOTE CONTROL AND FRONT PANEL
1 Infrared transmitter
Outputs infrared controls signals. Aim this transmitter at
the component you want to operate.
2 FM MODE
Switches the FM radio wave reception mode (stereo or
monaural) when this unit is in the FM tuning mode (see
page 11).
3 DIMMER
Changes brightness level of the front panel display.
Choose brightness from 3 levels by pressing this button
repeatedly.
y
This setting is retained even if you turn off this unit.
4 PRESET F / G
Switches the preset stations.
5 MEMORY
Sets this unit to the preset station memory mode (see
pages 7, 12).
6 B / C / D / E, ENTER
Selects and confirms an item.
7 INFO/TEXT
Turns on and changes the DAB station information (see
page 10) on the front panel display.
8 Numeric buttons, ENTER
Selects the desired preset stations (see pages 7, 12).
y
To enter number less than 10 (i.e. 1 to 9), press the desired
number and then ENTER, or press 0 and then enter the desired
number.
2 En
REMOTE CONTROL AND FRONT PANEL
9 BAND
Selects the reception band (DAB, FM, or AM).
Use the remote control within 6 m (20 ft) of this unit and
point it toward the remote control sensor. It receives
signals from a remote control provided with a Yamaha
amplifier or AV receiver.
A A (standby/on)
Turns on this unit. Press this button again to set this unit to
the standby mode.
Remote control
sensor
y
The standby/on indicator lamp above lights up when this unit is
turned on.
Note
In the standby mode, this unit consumes a small amount of power
in order to receive infrared signals from the remote control.
B TUNING H / I
• Selects the desired frequency when you press this
button.
• Searches the next FM or AM station when you press
and hold this button for more than 2 seconds.
C FUNCTION
Activates the function set up menu (see pages 8, 13).
D CLEAR
• Clears a preset station (see pages 8, 13).
• Clears all station information and preset settings in the
DAB tuning mode when you press and hold this button
for more than 3 seconds (see page 9).
• Clears all preset stations in the FM or AM tuning mode
when you press and hold this button for more than 3
seconds (see page 13).
Approximately
6 m (20 ft)
30º
30º
Notes
• Do not spill liquid on the remote control.
• Do not drop the remote control.
• Do not leave the remote control in the following places:
– hot or humid places such as a bathroom or near heater
– extremely cold places
– dusty places
■ Installing the battery in the remote
control
Change the battery when the operation range of the remote
control decreases.
Straight pin
E STEREO indicator
Lights up when this unit is in the stereo playback.
F TUNED indicator
Lights up when this unit is tuned into a station.
G Multi-information display
Displays tuning status messages and the DAB station
information.
H SECONDARY indicator
Lights up when this unit is in the DAB tuning mode and
receiving a secondary station.
Battery (CR2025)
(supplied)
CAUTION
• Keep the battery out of the reach of children, so that it
is not mistakenly swallowed.
• Insert the battery according to the polarity markings.
I TUNING MODE
Selects the tuning mode (automatic, manual, or preset
tuning).
J PRESET/TUNING
• Searches the next FM or AM station when this unit is
in the automatic tuning mode.
• Selects the desired frequency when this unit is in the
manual tuning mode.
• Switches the preset stations when this unit is in the
preset tuning mode.
3 En
PREPARATION
0 AUTO SCAN
Starts the automatic scanning function (see pages 6, 12).
■ Using the remote control
CONNECTIONS
Note
If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center
about outdoor antennas.
Indoor FM
antenna
(supplied)
AM loop antenna (supplied)
Indoor DAB antenna (supplied)
• The AM loop antenna should always be connected, even if
an outdoor AM antenna is connected to this unit.
• The AM loop antenna should be placed away from this
unit.
Stretch out the antenna and place it to
find the best reception position then fix it.
y
It is recommended that you use the
Tune Aid function in order to
maximize DAB reception capability
(see page 9).
RCA stereo
cable
(supplied)
To the AC wall outlet
Optical
cable
Coaxial digital
audio cable
CAUTION
Do not connect power
cable until all cable
connection are complete.
Note
Analog audio
input
Amplifier
Digital audio
input
The DIGITAL (DAB) OUTPUT jacks (OPTICAL
and COAXIAL) output the digital audio signals
(PCM signals) when this unit is in the DAB tuning
mode. DAB audio signals are also output the
ANALOG OUTPUT jack of this unit. FM or AM
audio signals are not output at the DIGITAL (DAB)
OUTPUT jacks.
Outdoor AM antenna
Use a 5 to 10 m of vinyl
covered wire extended
outdoors from a window.
Ground
For maximum safety and minimum interference, connect the
antenna GND terminal to a good earth ground.
A good earth ground is a metal stake driven into moist earth.
■ Assembling the supplied AM loop
antenna
■ Connecting the wire of the AM loop
antenna
black
white
4 En
OPERATIONS
DAB TUNING
Preparing the DAB tuning
Before tuning into DAB stations, you must perform the
automatic scanning. The scanning starts automatically
when you select DAB as the input source for the first time.
AUTO SCAN
OPERATIONS
DAB (Digital Audio Broadcasting) uses digital signals for
clearer sound and more stable reception compared to
analog signals.
DAB is broadcasted in blocks of data called “ensembles”
containing up to several radio stations that are
simultaneously broadcasted.
DAB can also include an extensive amount of text
information - called DLS (Dynamic Label Segment, see
page 10) - which is displayed on the front panel display of
the unit, enabling you to select a station by name.
DAB+ is a standard for digital radio broadcasts that uses
the MPEG4 HE-AAC v2 audio format and provides
higher quality sound than DAB.
BAND
AUTO SCAN
BAND
Press BAND repeatedly to select DAB as the
reception band.
The scanning starts automatically.
The number of channels found is displayed on the front
panel display.
Once the scanning is complete, this unit is tuned into the
first DAB station in the registry list.
Notes
• Be sure to check the DAB coverage in your area in that not all
areas are currently being covered. For a list of nationwide DAB
statuses and worldwide DAB frequencies, check WorldDMB
online at http://www.worlddab.org/.
• The sound quality and station information are controlled by the
DAB broadcaster, not this unit. Not all DAB broadcasters
transmit station information.
• DAB signals are broadcast in Band III (174 - 240 MHz) and L
Band (1452 - 1492 MHz).
If the automatic scanning operation is not
successful...
“No stations Available” and then following is
displayed on the front panel display.
1
Press B / C to select “Tune Aid” or
“Autoscan”.
2 Press E or ENTER.
The selected function (“Tune Aid” or “Autoscan”)
starts.
y
• For details on the Tune Aid function, see page 9.
• For details on the Autoscan Full function, see page 6.
• For further details about problems and their remedies, see
page 14.
5 En
DAB TUNING
■ Using the automatic scanning function
Use the automatic scanning function to scan the DAB
station again.
Autoscan Full (Full range scanning)
This unit scans the entire range of Band III and L Band
(see page 10).
Press and hold AUTO SCAN for more than 2
seconds.
This unit starts the full range scanning. “Autoscan Full” is
displayed on the front panel display.
Once this unit has finished scanning, this unit is tuned into
the first DAB station in the registry list.
Manual tuning
Use this feature to select the desired DAB station by
browsing the registry list.
Note
Once you have performed the automatic scanning, the registry list
of available stations is updated automatically as long as this unit
is in the DAB tuning mode. To register new ensembles, use the
automatic scanning function (see page 5).
Autoscan Local (Local range scanning)
This unit scans the limited range of Band III.
BAND TUNING PRESET/
TUNING
MODE
Press AUTO SCAN.
This unit starts the local range scanning. “Autoscan
Local” is displayed on the front panel display.
Once this unit has finished scanning, this unit is tuned into
the first DAB station in the registry list.
BAND
TUNING H / I
1
Press BAND repeatedly to select DAB as the
reception band.
2
Press TUNING H / I to select the desired
DAB station.
When this unit tuned into a station, the TUNED
indicator lights up.
y
On the front panel, press TUNING MODE repeatedly to
select “Manual tune” and then rotate PRESET/TUNING.
Current DAB station
SECONDARY indicator
If the selected DAB station is a secondary station, the
SECONDARY indicator lights up.
Note
“Off air” is displayed when this unit can not receive the specified
DAB station.
y
You can change the order of the DAB stations listen in the
registry listed by using the “Station order” function (see page 8).
6 En
DAB TUNING
Presetting DAB stations
4
You can tune into stations easily by storing (presetting)
and recalling them. This function enables this unit to
preset up to 40 DAB stations.
Press MEMORY or ENTER to confirm the
preset.
Note
When you preset a new station to an existing preset number, new
preset data will overwrite the existing preset data.
y
To clear the preset DAB station, see “Clearing the preset DAB
station” on page 8.
MEMORY
BAND
PRESET F / G
BAND
■ Recalling the preset DAB stations
You can tune into any desired station simply by selecting
the preset number.
1
Press BAND repeatedly to select DAB as the
reception band.
2
Press PRESET F / G or the numeric buttons
to select the desired preset number.
When this unit is tuned into the selected station, the
TUNED indicator lights up.
MEMORY
Numeric
buttons
ENTER
CLEAR
■ Storing DAB stations
1
Tune into the desired DAB station.
See page 6 for tuning instructions.
2
Press MEMORY.
The preset number blinks on the front panel display
for 10 seconds.
y
• On the front panel, press TUNING MODE repeatedly to
select “Preset tune” and then rotate PRESET/TUNING.
• “CHXX Empty” (XX indicates the preset number) is
displayed briefly when no preset DAB station is assigned
to the corresponding preset number. The DAB station
currently being received is then displayed on the front
panel display.
Note
Perform the next operation within 10 seconds after pressing
MEMORY.
3
Press PRESET F / G or the numeric buttons
to select the desired preset number while the
preset number blinks.
y
On the front panel, rotate PRESET/TUNING.
Note
Perform the next operation within 10 seconds after selecting
the preset number.
7 En
OPERATIONS
PRESET/
TUNING
CLEAR
DAB TUNING
■ Clearing the preset DAB station
Follow the steps below to clear a preset DAB station one
at a time.
1
Select the desired preset number.
See “Recalling the preset DAB stations” on page 7.
2
Press CLEAR.
The selected preset number blinks on the front panel
display.
Using the DAB functions
Use this feature to set the DAB functions.
BAND
B/C/D/E
/ENTER
FUNCTION
1
Press BAND repeatedly to select DAB as the
reception band.
2
Press FUNCTION.
The DAB function menu is displayed on the front
panel display.
3
Press B / C to select the desired DAB
function and then press E or ENTER.
You can select the following functions.
• Station Order (see page 8)
• Tune Aid (see page 9)
• Dynamic Range (see page 9)
• DAB Clear (see page 9)
• Auto Power Down (see page 9)
Note
If you do not perform the next operation within 10 seconds,
the clearing is canceled.
3
Press CLEAR again to confirm.
“CHXX cleared” (XX indicates the preset number) is
displayed on the front panel display.
y
• To clear all preset DAB stations, press and hold CLEAR
for more than 3 seconds. After all preset DAB stations are
cleared, the Autoscan Full function starts automatically
(see page 6).
• You can also clear all preset DAB stations by using the
DAB functions. See “DAB Clear” on page 9.
y
To exit from the DAB function menu, press FUNCTION again or
press D.
■ Station Order
You can change the order of the registered DAB stations.
1
8 En
Select “Station Order” in the DAB function
menu.
DAB TUNING
2
■ DAB Clear
Press B / C to select the desired station
order setting and then press ENTER.
Description
Alphanumeric
Default setting. Stations are listed in the
alphanumeric order.
Active
This unit lists the currently active DAB
stations first, and then other DAB
stations in the alphanumeric order.
Ensemble
Select this setting to browse through the
registered DAB stations from the lowest
to the highest channel labels (see page
10).
y
You can also perform DAB Clear by pressing and holding
CLEAR for more than 3 seconds in the preset tuning mode. See
“Clearing the preset DAB station” on page 8.
Note
Once DAB Clear is performed, the deleted information and preset
settings cannot be restored.
1
Select “DAB Clear” in the DAB function
menu.
2
Press B / C to select “OK” and then press E
or ENTER.
After DAB Clear is complete, the Autoscan Full
function starts automatically (see page 6).
y
While pressing B / C to select the desired setting, “*” is
displayed next to the current setting.
■ Tune Aid
Measure reception strength of the received signal (from 0
(none) to 100 (best)).
To cancel the operation, select “CANCEL”.
1
Select “Tune Aid” in the DAB function menu.
2
Press B / C to select the desired DAB
channel.
The strength of the selected DAB channel signal is
displayed on the front panel display. Adjust the
orientation of the DAB antenna so that the strength of
the selected DAB channel signal gets stronger.
■ Dynamic Range
You can change the dynamic range compression setting.
This is especially useful when you listen to a DAB station
in a noisy environment or at a low volume at night.
1
2
y
Select “Dynamic Range” in the DAB function
menu.
Press B / C to select the desired dynamic
range compression setting and then press E
or ENTER.
Choice
Description
AUTO
Default setting. This unit utilizes the
dynamic range compression
automatically if it is transmitted.
OFF
This unit does not utilize the dynamic
range compression.
■ Auto Power Down
This unit automatically enters standby mode if it is not
operated for specified amount of time.
This setting is effective for all tuning modes.
1
Select “Auto Power Down” in the DAB
function menu.
2
Press B / C to select the desired auto power
down setting and then press E or ENTER.
Choice
Description
OFF
This unit will not be set to standby
mode automatically.
4 Hours,
8 Hours,
12 Hours
This unit is set to standby mode
automatically after the specified
amount of time passes.
Default setting is “8 Hours”.
y
While pressing B / C to select the desired setting, “*” is
displayed next to the current setting.
y
While pressing B / C to select the desired setting, “*” is
displayed next to the current setting.
9 En
OPERATIONS
Choice
Clears all DAB station information and preset settings
stored in the unit.
DAB TUNING
DAB station information
Use this feature to display various information about the
current DAB station.
DAB frequency information
■ Band III
Note
When you perform the local range scanning, this unit scans only
within the frequencies marked with an asterisk (*) in the
following table (see page 6).
INFO/TEXT
Frequency
Channel
label
174.928 MHz
5A
* 208.064 MHz
9D
176.640 MHz
5B
* 209.936 MHz
10A
178.352 MHz
5C
* 211.648 MHz
10B
180.064 MHz
5D
* 213.360 MHz
10C
181.936 MHz
6A
* 215.072 MHz
10D
183.648 MHz
6B
* 216.928 MHz
11A
185.360 MHz
6C
* 218.640 MHz
11B
187.072 MHz
6D
* 220.352 MHz
11C
188.928 MHz
7A
* 222.064 MHz
11D
190.640 MHz
7B
* 223.936 MHz
12A
192.352 MHz
7C
* 225.648 MHz
12B
194.064 MHz
7D
* 227.360 MHz
12C
195.936 MHz
8A
* 229.072 MHz
12D
197.648 MHz
8B
* 230.784 MHz
13A
199.360 MHz
8C
* 232.496 MHz
13B
201.072 MHz
8D
* 234.208 MHz
13C
* 202.928 MHz
9A
* 235.776 MHz
13D
* 204.640 MHz
9B
* 237.488 MHz
13E
* 206.352 MHz
9C
* 239.200 MHz
13F
Frequency
Channel
label
Frequency
Channel
label
1452.960 MHz
LA
1473.504 MHz
LM
1454.672 MHz
LB
1475.216 MHz
LN
Channel & frequency
Displays the channel label and frequency of the current
DAB station (See page 10).
1456.384 MHz
LC
1476.928 MHz
LO
1458.096 MHz
LD
1478.640 MHz
LP
1459.808 MHz
LE
1480.352 MHz
LQ
Signal quality
Displays the signal reception quality (from 0 (none) to 100
(best)) of the current DAB station.
1461.520 MHz
LF
1482.064 MHz
LR
1463.232 MHz
LG
1483.776 MHz
LS
1464.944 MHz
LH
1485.488 MHz
LT
1466.656 MHz
LI
1487.200 MHz
LU
1468.368 MHz
LJ
1488.912 MHz
LV
1470.080 MHz
LK
1490.624 MHz
LW
1471.792 MHz
LL
INFO/TEXT
1
2
Tune into the desired DAB station.
Press INFO/TEXT repeatedly to display
information about the current DAB station.
DLS (Dynamic Label Segment)
Displays information about the current DAB station, such
as the name of the song, artist and speaker, etc. This data
is continuously updated by the DAB broadcaster, thus
changing often with every new song or program. Other
data, such as news, weather, and sports headlines, may be
broadcast as well.
Audio mode
Displays bit rate and digital radio format (DAB or DAB+).
Program type
Displays the genre of the current DAB station.
Ensemble label
Displays the name of the current ensemble.
Date & time
Displays the current date and time.
y
The front panel display can display up to 16 alphanumeric
characters at once. The dynamic label segment scrolls in a
continuous manner.
10 En
Frequency
Channel
label
■ L Band
FM/AM TUNING
■ Manual tuning
Automatic and manual tuning
FM MODE
If the signal from the station you want to select is weak,
tune into it manually.
BAND
PRESET/
TUNING
Press BAND repeatedly to select FM or AM
as the reception band.
2
Press TUNING H / I to select the desired
frequency.
When this unit is tuned into a station, the TUNED
indicator lights up.
y
FM MODE
BAND
TUNING H / I
■ Automatic tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
1
Press BAND repeatedly to select FM or AM
as the reception band.
2
Press and hold TUNING H / I for more than
2 seconds to begin automatic tuning.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the station is
displayed on the front panel display.
On the front panel, press TUNING MODE repeatedly to
select “Manual tune” and then rotate PRESET/TUNING.
■ Improving FM reception
If the signal from the station is weak and the sound quality
is not good, set the FM radio wave reception mode to the
monaural tuning mode to improve reception.
Press FM MODE repeatedly to select “AUTO
STEREO” (stereo mode) or “MONO” (monaural
mode) when this unit is tuned into an FM radio
station.
• When this unit is in the stereo tuning mode, the
STEREO indicator lights up on the front panel display.
• When this unit is in the monaural tuning mode, the
STEREO indicator goes off.
Note
Even if this unit is in the stereo tuning mode, the STEREO
indicator does not light up when the current program is monaural.
y
On the front panel, press TUNING MODE repeatedly to
select “Auto tune” and then rotate PRESET/TUNING.
11 En
OPERATIONS
TUNING
MODE
1
FM/AM TUNING
■ Manual station preset
Presetting stations
You can tune into stations easily by storing (presetting)
and recalling them. This function enables this unit to
preset up to 30 stations for each band.
1
Tune into the desired FM/AM station.
See page 11 for tuning instructions.
2
Press MEMORY.
The preset number blinks on the front panel display
for 10 seconds.
Note
AUTO SCAN
MEMORY
BAND
CLEAR
PRESET/
TUNING
Perform the next operation within 10 seconds after pressing
MEMORY.
3
PRESET F / G
AUTO SCAN
BAND
Press PRESET F / G or the numeric buttons
to select the desired preset number while the
preset number blinks.
MEMORY
Numeric
buttons
Preset number
ENTER
y
CLEAR
On the front panel, rotate PRESET/TUNING.
Note
■ Automatic station preset
1
2
Press BAND repeatedly to select FM or AM
as the reception band.
Press AUTO SCAN.
“Auto Preset” blinks on the front panel display. This
unit starts searching the stations with strong signals
and stores them automatically.
Perform the next operation within 10 seconds after selecting
the preset number.
4
Press MEMORY or ENTER to confirm the
preset.
Notes
• When you preset a new station to an existing preset number,
new preset data will overwrite the existing preset data.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
■ Recalling preset stations
When automatic station preset is completed, this unit
tunes into the station preset to “01”.
Notes
• FM or AM with sufficient signal strength are stored
automatically. To store a station with weak signal strength, store
it manually. See “Manual station preset” below.
• When you rerun “Automatic station preset”, all of the preset
data will be deleted and new preset data will be set to each
preset number.
• If no station is found, the search ends and this unit returns to the
previous station tuned in before the search.
12 En
You can tune into any desired station simply by selecting
the preset number.
1
Press BAND repeatedly to select FM or AM
as the reception band.
2
Press PRESET F / G or the numeric buttons
to select the desired preset number.
y
• On the front panel, press TUNING MODE repeatedly to
select “Preset tune” and then rotate PRESET/TUNING.
• “CHXX Empty” (XX indicates the preset number) is
displayed briefly when no preset FM or AM station is
assigned to the corresponding preset number. The FM or
AM station currently being received is then displayed on
the front panel display.
FM/AM TUNING
■ Clearing the preset FM or AM station
Follow the steps below to clear a preset FM or AM station
one at a time.
1
Select the desired preset number.
See “Recalling preset stations” on page 12.
2
Press CLEAR.
The selected preset number blinks on the front panel
display.
Using the FM/AM functions
Use this feature to set the FM/AM functions.
BAND
B/C/D/E/
ENTER
FUNCTION
Press BAND repeatedly to select FM or AM
as the reception band.
2
Press FUNCTION.
The FM/AM function menu is displayed on the front
panel display.
3
Press B / C to select desired FM/AM function
and then press E or ENTER.
You can select the following functions.
• Presets Clear (see page 13)
• Auto Power Down (see page 13)
If you do not perform the next operation within 10 seconds,
the clearing is canceled.
3
Press CLEAR to confirm.
“CHXX cleared” (XX indicates the preset number) is
displayed on the front panel display.
y
• To clear all preset FM or AM stations, press and hold CLEAR
for more than 3 seconds.
• You can also clear all preset FM or AM stations, by using the
FM/AM functions. See “Presets Clear” on page 13.
y
To exit from the FM/AM function menu, press FUNCTION
again or press D.
■ Presets Clear
Clears all preset settings stored in the unit for the current
tuning mode.
y
You can also perform Presets Clear by pressing and holding
CLEAR for more than 3 seconds in the preset tuning mode. See
“Clearing the preset FM or AM station” on page 13.
Note
Once Presets Clear is performed, the deleted preset settings
cannot be restored.
1
Select “Presets Clear” in FM/AM function
menu.
2
Press B / C to select “OK” and then press E
or ENTER.
y
To cancel the operation, select “CANCEL”.
■ Auto Power Down
This unit automatically enters standby mode if it is not
operated for specified amount of time.
This setting is effective for all tuning modes. See “Auto
Power Down” on page 9 for detail.
13 En
OPERATIONS
Note
1
ADDITIONAL INFORMATION
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cable, and contact the
nearest authorized Yamaha dealer or service center.
■ Tuner
Problem
Cannot tune into any
DAB stations.
Remedy
See
page
The automatic scanning operations
were not performed, or the DAB
registry list needs to be updated.
Perform the automatic scanning operations.
There is no DAB coverage in your
area.
Check with your dealer or WorldDMB online
at “http://www.worlddab.org” for a listing of
the DAB coverage in your area.
—
The DAB signals are too weak.
Use a high-quality outdoor DAB antenna.
—
The DAB antenna may not be
connected.
Make sure the DAB antenna is firmly
connected.
4
The DAB signals are too weak.
Use a high-quality outdoor DAB antenna.
—
There is no DAB coverage in your
area.
Check with your dealer or WorldDMB online
at “http://www.worlddab.org/” for a listing of
the DAB coverage in your area.
—
The positioning of the indoor DAB
antenna and/or this unit is not optimal
for DAB reception.
Use the tuning aid feature to locate the best
positioning of the DAB antenna and this unit
for optimal DAB reception.
9
The DAB signals are too weak.
Use a high-quality outdoor DAB antenna.
—
There is noise
interference (e.g. hiss
or crackle).
The indoor DAB antenna needs to be
repositioned.
Readjust the position of the indoor DAB
antenna.
—
The DAB signals are too weak.
Use a high-quality outdoor DAB antenna.
—
The DAB station
information does not
appear or is inaccurate.
The DAB station may be temporarily
out of service, or the DAB station
information is not provided by the
DAB broadcaster.
Contact the DAB broadcaster.
The automatic scanning
operations are not
successful.
DAB
The DAB station
reception is weak.
14 En
Cause
6
—
TROUBLESHOOTING
Problem
FM stereo reception is
noisy.
FM
AM
Cause
Remedy
See
page
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Check the antenna connections.
4
Try using a high-quality directional FM
antenna.
—
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna position to eliminate
multi-path interference.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
There are continuous
crackling and hissing
noises.
There are buzzing and
whining noises.
Use a high-quality directional FM antenna.
Use the manual tuning method.
—
—
11
—
Use the manual tuning method.
11
Noise can result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a earth ground.
This will help somewhat, but it is difficult to
eliminate all noise.
—
A TV set is being used nearby.
Move this unit away from the TV set.
—
■ General
Problem
This unit fails to turn on when
A is pressed.
Cause
Remedy
The power cable is not connected or
the plug is not completely inserted.
Connect the power cable firmly.
This unit has been exposed to a strong
external electric shock (such as
lightning or strong static electricity).
Disconnect the power cable, plug it back in
after 30 seconds, then use it normally.
A “humming” sound can be
heard.
Incorrect cable connections.
Firmly connect the audio connection cord
plugs. If the problem persists, the cables may
be defective.
This unit does not operate
properly.
The internal microcomputer has been
frozen by an external electric shock
(such as lightning or excessive static
electricity) or by a power supply with
low voltage.
Disconnect the AC power plug from the
outlet and then plug it in again after about 30
seconds.
The Auto Power Down function has
turned this unit off.
Change the auto power down setting.
This unit suddenly turns off.
See
page
4
—
—
4
9
15 En
ADDITIONAL
INFORMATION
Tighten the AM loop antenna connections
and orient it for the best reception.
SPECIFICATIONS
DAB SECTION
GENERAL
• Output Level/Impedance ............................................. 1.5 V/1.2 kΩ
• Power Supply ........................................................ AC 240 V, 50 Hz
• Tuning Range
(Band III) ............................................................. 174 to 240 MHz
(L-Band) .......................................................... 1452 to 1492 MHz
• Power Consumption ................................................................. 10 W
• Sensitivity
(Band III) ........................................................................ –98 dBm
(L-Band) ......................................................................... –93 dBm
• Selectivity (for adjacent channel)
(Band III) .............................................................................. 40 dB
(L-Band) ............................................................................... 40 dB
• Dimensions (W x H x D) ................................... 435 x 87 x 306 mm
(17 1/8 x 3 3/8 x 12 in)
• Weight ..................................................................................... 3.3 kg
(7.3 lbs)
* Specifications are subject to change without notice.
• Signal to Noise Ratio .............................................................. 95 dB
• Total Harmonic Distortion ..................................................... 0.01%
• Stereo Separation (1 kHz) ....................................................... 77 dB
• Frequency Response .................. 20 Hz to 20 kHz, +0.5 dB/–1.0 dB
• Antenna Input (unbalanced) ..................................................... 75 Ω
FM SECTION
• Output Level/Impedance ............................................. 1.0 V/1.2 kΩ
• Tuning Range ................................................. 87.50 to 108.00 MHz
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono .................................................................... 3 µV (20.2 dBf)
• Usable Sensitivity (Signal to Noise Ratio, 30 dB, Mono) .... 1.0 µV
• Image Rejection Ratio ............................................................. 80 dB
• IF Rejection Ratio ................................................................... 70 dB
• Selectivity (400 kHz) .............................................................. 70 dB
• Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 80 dB/75 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................ 0.3%/0.5%
• Stereo Separation (40 kHz Dev.)
1 kHz .................................................................................... 43 dB
• Frequency response (20 Hz to 15 kHz).................................... –3 dB
• Antenna Input (unbalanced) ..................................................... 75 Ω
AM SECTION
• Output Level/Impedance ........................................... 0.36 V/1.2 kΩ
• Tuning Range ........................................................ 531 to 1611 kHz
• Usable Sensitivity ............................................................. 300 µV/m
• Signal to Noise Ratio .............................................................. 50 dB
• Harmonic Distortion ................................................................. 1.0%
16 En
This receiver supports DAB/DAB+ tuning.
© 2010 Yamaha Corporation
Printed in China
CQX1A1549Z