SPCK620/623 Comfort Keypad - User Manual
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security
Security
Further
information
Target group
General safety instructions
Meaning of written warning notices
Meaning of hazard symbols
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > Target group
Target group
The instructions in this documentation are directed at the following target group:
End user
Instruction by technical specialists is necessary.
Performs only the procedures for proper operation of the product.
The product is installed and configured.
Target readers
Qualification
Activity
Condition of the product
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > General safety instructions
General safety instructions
Further
information
General information
Operation
Service and maintenance
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > General safety instructions > General information
General information
Read the general safety precautions before operating the unit.
Keep this document for later reference.
Always pass this document on together with the product.
Please also take into account any additional country-specific, local safety standards or regulations concerning
project planning, operation and disposal of the product.
Liability
claim
Do not make any changes or modifications to the device unless they are expressly mentioned in this manual and
have been approved by the manufacturer.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > General safety instructions > Operation
Operation
Dangerous situation due to false alarm
Make sure to notify all relevant parties and authorities providing assistance before testing the system.
To avoid panic, always inform all those present before testing any alarm devices.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > General safety instructions > Service and maintenance
Service and maintenance
Danger of electrical shock during maintenance
Maintenance work must only be carried out by trained specialists.
Danger of electrical shock while cleaning the device
Do not use liquid cleaners or sprays that contain alcohol, spirit or ammonia.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > Meaning of written warning notices
Meaning of written warning notices
DANGER
Danger of death or severe bodily harm.
WARNING
Possible danger of death or severe bodily harm.
CAUTION
Danger of minor bodily injury or property damage
IMPORTANT
Danger of malfunctions
Signal Word
Type of Risk
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Security > Meaning of hazard symbols
Meaning of hazard symbols
WARNING
Warning of hazard area
WARNING
Warning of dangerous electrical voltage
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Directives and standards
Directives and standards
Further
information
EU directives
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Directives and standards > EU directives
EU directives
This product complies with the requirements of the European Directives 2004/108/EC “Directive of Electromagnetic
Compatibility” and 2006/95/EC “Low Voltage Directive”. The EU declaration of conformity is available to the
responsible agencies at:
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
Siemensallee 84
76181 Karlsruhe
European
Directive
2004/108/EC
„Electromagnetic
Compatibility”
Compliance with the European Directive 2004/108/EC has been proven by testing according to the following standards:
emc emission
EN 55022 Class B
emc immunity
EN 50130-4
European
Directive
2006/95/EC
„Low-Voltage
Directive”
Compliance with the European Directive 2006/95/EC has been proven by testing according to the following standard:
Safety
EN 60950-1
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Introduction
Introduction
The keypad is a wall-mounted interface that allows:
Engineers to program the system through the Engineer Programming menus (password protected) and to set/unset
the system; a user can control the system on a day-to-day basis.
Users to enter User Programming menus (password protected), and to perform operational procedures (set/unset) on
the system.
The SPCK620 is equipped with soft keys and large graphical LCD for easy operation. The functionality can be enhanced
with key switch expander SPCE110 or indication expander SPCE120.
The SPCK623 is equipped with a proximity card reader (125 kHz EM 4102) for easy user access, soft keys, large
graphical LCD and voice annunciation support. The functionality can be enhanced with key switch expander SPCE110
or indication expander SPCE120.
1
LED status indicators
The LED status indicators provide information on the current status of the system as detailed in the table below.
2
LCD display
The keypad display shows all alert and warning messages and provides a visual interface for programming the system
(engineer programming only). The display can be configured under which conditions the backlight comes on.
3
Soft function keys
Context sensitive keys to navigate through menus/programming.
4
Enter key
Confirm display or input.
5
Back menu key
Go back in the menu
Reset buzzers, siren and alarms in the memory.
6
Proximity device receiver area
Only SPCK 623: If the keypad has been fitted with a proximity device receiver, users should present the Portable ACE
Fob to within 1 cm of this area.
7
Alphanumeric keys
Alphanumeric keypad allow for both text and numeric data entry during programming. Alphabetic characters are
selected by applying the appropriate number of key presses. To switch between upper and lower case characters, press
the hash (#) key. To enter a numeric digit, hold down the appropriate key for 2 seconds.
8
Multi-functional navigation key
Navigation through menus.
9
Information key
Displays information.
Further
information
LED description
Viewing mode description
Function keys in idle state
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Introduction > LED description
LED description
Symbol
Color
Operation
Display from …
Blue
On
The system cannot be set. Forced setting is possible (faults or open zones can be inhibited).
Flashing
The system cannot be set or forced set (faults or open zones cannot be inhibited).
Off
The system can be set.
Amber
Flashing
Engineer is on site.
Green
On
Assigned area is unset.
Flashing
Assigned area is Partset A / B
Off
Assigned area is fullset
Red
On
Alarm
Flashing
Off
No alarm
SPCK620_23_ico_fault
Amber
On
Flashing
Trouble
Off
No trouble
Green
On
System ok
Flashing
Mains fault
Off
No bus connection
NOTICE
The LED indications for information, area status, alarm and fault is deactivated in idle state of the keypad. A valid
user PIN has to be entered. It is configurable if the power indication can be seen in idle state.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Introduction > Viewing mode description
Viewing mode description
There are 2 viewing modes (automatic):
Multi area view: User has access to several areas. Displaying the areas is done via area groups. If no area group is
configured, only the general group “All my areas” is displayed.
Single area view: The user has only rights for 1 area. In the single area view, only one area is displayed in large fonts and
can be controlled directly.
NOTICE
The rights of a user can be restricted by the user settings or the settings of the keypad the user is logging in. Only
if the user and the keypad he is logging in have the right for an area, the area is displayed. If the user has the right
for several areas but the keypad has only the right for one area, the user will also see the single area view.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Introduction > Function keys in idle state
Function keys in idle state
Emergency
Keys
Depending on configuration emergency keys are displayed. A simultaneous pressing of the keys activates an emergency
call.
SPCK620_23_ico_panic_alarm
Panic Alarm
Fire alarm
SPCK620_23_ico_medical_alarm
Medical Alarm
The activated process depends on the system configuration. Please ask the installer for details.
Direct
Settings
Depending on configuration the direct set option is displayed. A forced set / part set without PIN is possible of the area
the keypad is assigned to.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Login
Login
Further
information
Login with PIN
Login with card (SPCK623)
Login with PIN and card (SPCK623)
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Login > Login with PIN
Login with PIN
The display in idle state shows an analogue clock as default, but may differ depending on system configuration.
The keypad is in idle state.
Enter the valid user code with the digit keys
to
.
The state of the area/area groups will be displayed.
NOTICE
How to correct input error
Delete incorrect input using the
key and then enter the PIN again.
If the PIN is entered incorrectly 4 times, then input is blocked for one minute.
Wait for this amount of time and subsequently enter the PIN correctly.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Login > Login with card (SPCK623)
Login with card (SPCK623)
The card / pace must be assigned to a user and stored in the control panel.
Present the card to the card reader of the keypad.
The card reader receiving area is next to the alphanumeric keypad and is indicated by following icon:
SPCS410_icn_card_reader_receiving_area
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Login > Login with PIN and card (SPCK623)
Login with PIN and card (SPCK623)
The card and PIN option has to be activated in the control panel.
1. Present the card / pace to the keypad.
2.
Enter the PIN with the keys
to
.
NOTICE
The pace has to be presented first.
If a code is entered first, the message “present pace” will be displayed. After presenting the pace, due to the forced
order, the PIN has to be entered again.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Single area view
Single area view
Further
information
Setting and unsetting the system
Setting not possible
Restoring an alarm
Resetting a fault
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Single area view > Setting and unsetting the system
Setting and unsetting the system
1. Enter a valid User code.
The following screen will be displayed.
2. Press the relevant context-sensitive function key to change the state of the area.
Following states are possible:
Symbol
Function
Fullset
Unset
Partset A
Partset B
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Single area view > Setting not possible
Setting not possible
If there is e.g. an open zone, the setting symbol will be displayed with an information symbol:
Press the softkey below the setting symbol.
In the next screen, the information will be shown.
Following states are possible:
Symbol
Function
None
This open zone can be inhibited (forced set is possible).
This open zone can not be inhibited (no forced set possible). Please contact your installer if symbol is still indicated
after closing according zone (e.g. window).
Only available if the zone attribute Exit open is enabled.
The Entry – Exit zone is open. Zone will not prevent setting process. Zone has to be closed at the end of the exit timer.
If the zone is still open, setting will fail.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Single area view > Restoring an alarm
Restoring an alarm
If there is any alarm, the alarm will be displayed after login.
The alarm will be displayed by the blinking symbol
and the blinking LED
.
Press the softkey below the blinking alarm symbol .
NOTICE
The location of the different setting softkeys is fixed. Due to this the location of the alarm icon can vary. In the
above picture, there is an alarm in fullset condition.
In the next screen, the alarm(s) will be listed.
There are 2 alarm symbols possible:
SPCK620_23_ico_alarm_not_restored
Alarm can not be restored . Alarm condition still present (e.g. the zone which caused the alarm is still open). Please contact
your installer if symbol is still indicated after closing according zone (e.g. window).
Alarm can be restored .
If the alarm can be restored, press the softkey below the symbol
SPCK620_23_ico_no_alarm
.
The alarm is restored.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Single area view > Resetting a fault
Resetting a fault
If there is any fault, this will be displayed after login:
SPCK620_23_ico_fault
The symbol
The LED
is blinking.
SPCK620_23_ico_img_warning
is blinking.
1. Press the softkey below the blinking fault symbol .
NOTICE
The location of the different setting softkeys is fixed. Due to this the location of the fault icon can vary. In the above
picture, there is a fault in unset condition.
2. In the next screen, the fault(s) will be listed.
There are 2 fault symbols possible:
SPCK620_23_ico_fault_not_restored
Fault can not be restored. Fault condition still present. Please contact your installer.
Fault can be restored.
If the fault can be restored, press the softkey below the symbol
SPCK620_23_ico_no_alarm
.
The fault is restored.
Ready will be shown on the display.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Multi area view
Multi area view
Further
information
Setting and unsetting the system
Setting not possible
Restoring an alarm
Resetting a fault
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Multi area view > Setting and unsetting the system
Setting and unsetting the system
Enter a valid User code
The names of the area groups are displayed.
The current state of the area group is indicated on the right in the display and by the LEDs above the display.
Following states are possible:
Symbol
Function
Fullset (all aras of the area group are Fullset)
Unset (all aras of the area group are Unset)
Mixed set (the areas of the area group have different setting states.).
Partset A (all aras of the area group are Partset A)
Partset B (all aras of the area group are Partset B)
To change the state of an area group:
1. Scroll using the
keys until the required area group is visible.
2. Press the relevant context-sensitive function key to change the state of the whole area group.
To change the state of a single area (mixed set possible):
1. Scroll using the
keys until the required area group is visible.
2.
Press
.
All areas of this area groups are listed.
3. Scroll using the
keys until the required area is visible.
4. Press the relevant context-sensitive function key to change the state.
To change the state of all areas:
1. Scroll using the key to ALL MY AREAS. (in area group view)
2. Press the relevant context-sensitive function key to change the state
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Multi area view > Setting not possible
Setting not possible
If there is e.g. an open zone, the setting symbol will be displayed with an information symbol:
1. Scroll using the
keys until the required area group is visible.
2.
Press
.
All areas of this area groups are visible.
1. Scroll using the
keys until the required area is visible.
2. Press the softkey below the setting symbol.
In the next screen, the information about that zone will be shown.
Following states are possible:
Symbol
Function
None
This open zone can be inhibited (forced set is possible).
This open zone can not be inhibited (no forced set possible). Please contact your installer if symbol is still indicated
after closing according zone (e.g. window).
Only available if the zone attribute Exit open is enabled.
The Entry – Exit zone is open. Zone will not prevent setting process. Zone has to be closed at the end of the exit timer. If
the zone is still open, setting will fail.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Multi area view > Restoring an alarm
Restoring an alarm
If there is any alarm, the alarm will be displayed after login.
The alarm will be displayed by the blinking symbol
and the blinking LED
.
NOTICE
There is a fixed soft key assignment to set / partset / unset areas or area groups. Due to this the location of the
alarm icon can vary. In the graphics below, there is an alarm in fullset condition.
1. Scroll using the
keys until the required area group is visible.
2.
Press
.
3. Scroll using the
keys until the required area is visible.
4. Press the softkey below the blinking alarm symbol.
In the next screen, the alarm(s) will be listed.
There are 2 alarm symbols possible:
SPCK620_23_ico_alarm_not_restored
Alarm can not be restored. Alarm condition still present (e.g. the zone which caused the alarm is still open). Please contact
your installer if symbol is still indicated after closing according zone (e.g. window).
Alarm can be restored.
If the alarm can be restored, press the key
SPCK620_23_ico_no_alarm
.
The alarm is restored.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Multi area view > Resetting a fault
Resetting a fault
If there is any fault, this will be displayed after login.
SPCK620_23_ico_fault
The symbol
The LED
is blinking.
SPCK620_23_ico_img_warning
is blinking.
NOTICE
In the below pictures a system wide fault (e.g. X-Bus cable fault) is indicated. Due to this the fault symbol is
displayed behind all area groups / areas. It is sufficient to restore the fault once. In this case it does not matter
which area group / area is selected.
1. Scroll using the
keys until the required area group is visible.
2.
Press
.
3. Scroll using the
keys until the required area is visible.
4. Press the softkey below the blinking fault symbol.
NOTICE
There is a fixed soft key assignment to set / partset / unset areas or area groups. Due to this the location of the
fault icon can vary. In the above picture, there is a fault in unset condition.
5. In the next screen, the fault(s) will be listed.
There are 2 fault symbols possible:
SPCK620_23_ico_fault_not_restored
Fault can not be restored. Fault condition still present. Please contact your installer.
Fault can be restored.
If the fault can be restored, press the softkey below the symbol
SPCK620_23_ico_no_alarm
.
The fault is restored.
Ready will be shown on the display.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus
User menus
For each menu option, the keypad must be in User programming and within the menu option MENUS:
1. Enter a valid User code (default 2222).
2. Scroll to MENUS and press SELECT.
3. To select a programming option, use the up/down arrow keys or enter the digit listed in the table below.
1
INHIBIT
Allows users to inhibit a zone.
2
ISOLATE
Allows users to isolate a zone.
3
SET DATE/TIME
Allows users to set the time and date.
4
TEST
Allows users to perform a bell test or walk test OR change the audible settings.
5
EVENT LOG
Allows users to view a log of the most recent events on the system.
6
CHIME
Allows users to set the chime attribute on a zone; used for testing zone inputs without triggering an alarm.
7
USERS
Allows Manager type users to add, edit, and delete users.
8
CHANGE CODE
Allows users to change their user code.
9
SETUP SMS
Allows users to set up the SMS service for sending short text messages to mobile phones via the PSTN Line.
DOOR CONTROL
Allows the user to control doors. He can lock / unlock and reset the door to normal operation.
0
GRANT ACCESS
Allows users to grant Engineer or Manufacturer access to the system.
If the security grade of the system is set to Engineer Configure, then the INHIBIT and ISOLATE features may not
be presented in the user menu. A Standard or Manager Type User profile must be created to provide access to the
user programming menus.
Further
information
INHIBIT
ISOLATE
TEST
SET DATE/TIME
EVENT LOG
CHIME
USERS
SMS
DOOR CONTROL
GRANT ACCESS
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > INHIBIT
INHIBIT
Zone and alerts from X-BUS devices can be manually inhibited from the keypad. Inhibiting a zone removes that zone from the
system for one alarm set period only.
To inhibit a zones or alerts from X-BUS devices:
1. Scroll to INHIBIT and press SELECT.
2. Scroll to the desired option in the table below and press SELECT:
ZONES
Select the required zone and toggle the setting from NOT INHIBITED to INHIBITED.
XBUS
Isolate the desired alert from EXPANDERS or KEYPADS:
XBUS COMMS LOST
XBUS FUSE FAULT (Expanders only)
X-BUS TAMPER
VIEW INHIBITS
To view a list of the inhibited zones, system alerts and E-BUS devices alerts.
Only the ALARM, EXIT/ENTRY, FIRE EXIT and LINE zone types can be inhibited on the SPC system. All other
zone types are not displayed in the inhibit menus.
If the security grade setting of the SPC system is set to Unrestricted (see page), then the option to inhibit zones
and fault conditions is displayed in the engineer inhibit menus.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > ISOLATE
ISOLATE
Zones, system alerts or alerts from X-BUS devices can be manually isolated from the keypad. Isolating a zone removes
that zone from the system until the user de-isolates it.
To isolate zones, system alerts or alerts from X-BUS devices:
1. Scroll to ISOLATE and press SELECT.
2. Scroll to the desired option in the table below and press SELECT.
ZONE
Select the required zone and toggle the setting from NOT ISOLATED to ISOLATED.
SYSTEM
Isolate the desired system alert.
XBUS
Isolate the desired alert from EXPANDERS or KEYPADS:
XBUS COMMS LOST
XBUS FUSE FAULT (Expanders only)
X-BUS TAMPER
VIEW ISOLATIONS
To view a list of the isolated zones, system alerts and X-BUS devices alerts.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > TEST
TEST
1. Scroll to TEST and press SELECT.
2. Scroll to the desired programming option.
Further
information
BELL TEST
WALK TEST
AUDIBLE OPTIONS
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > TEST > BELL TEST
BELL TEST
To perform a bell test:
1. Scroll to TEST > BELL TEST.
2. Press SELECT.
When BELL TEST is selected, the following options available: EXTERNAL BELLS, STROBE, INTERNAL
BELLS and BUZZER. When each of these options is selected, the device sounds to verify it is operating correctly.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > TEST > WALK TEST
WALK TEST
A walk test ensures that the sensors are operating correctly on the SPC system.
To perform a walk test:
1. Scroll to TEST > WALK TEST.
2. Press SELECT.
The display indicates the number of zones to be tested on the system with the text TO TEST XX (where XX is the
number of valid walk test zones).
Panic zones, Fire zones, Fire Exit zones, and Holdup zones are included in the walk test as activation of these
zone types do not generate an alarm.
NOTICE
Valid walk test zones are defined as all zone types with the exception of Panic zones, Fire zones, Fire Exit zones,
and Holdup zones.
Do not activate zone types during a walk test.
1. Locate the sensor on the first zone and activate it (open the door or window).
The keypad buzzer sounds continuously for approximately 2 seconds to indicate that the zone activation has been
detected and the number of zones left to test (displayed on the keypad) decreases.
2. Continue with the remaining zones on the system until all zones have been tested. If a zone activation does not get
acknowledged by the system, check the wiring of the sensor and/or replace with another sensor if necessary.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > TEST > AUDIBLE OPTIONS
AUDIBLE OPTIONS
The audible options are applied as indicators within a walk test.
To set the audible options:
1. Scroll to AUDIBLE OPTIONS.
2. Press SELECT.
3. Scroll to one of the following options: ALL, INT BELL, EXT BELL, KEYPAD
4. Press SAVE.
5. Press BACK to exit.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > SET DATE/TIME
SET DATE/TIME
The date and time can be manually entered on the system. The time and date information is displayed on the keypad and
browser and is used on time-related programming features.
1. Scroll to SET DATE/TIME and press SELECT.
The date displays on the top line of the display.
2. To enter a new date, press the required numeric keys. To move the cursor to the left and right, press the left and
right arrow keys.
3. Press ENTER to save the new date.
If an attempt is made to save an invalid date value, the text INVALID VALUE is displayed for 1 second and
the user is prompted to enter a valid date.
4. To enter a new time, press the required numeric keys. To move the cursor to the left and right, press the left and
right arrow keys.
5. Press ENTER to save the new time.
If an attempt is made to save an invalid time value, the text INVALID VALUE is displayed for 1 second and
the user is prompted to enter a valid time.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > EVENT LOG
EVENT LOG
Recent events on the system are displayed in the EVENT LOG option. Events flash in one second intervals.
1. Scroll to EVENT LOG and press SELECT.
2. To view an event from a particular date, enter the date with the numeric keys.
The most recent events are displayed on the bottom line of the display. All previous events are displayed for
one second in turn.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > CHIME
CHIME
The chime function can be enabled or disabled on all zones where the chime has been programmed as an audible alert
feature.
To enable or disable the chime function:
1. Scroll to CHIME and press SELECT.
2. Toggle between ENABLED and DISABLED for the chime.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > USERS
USERS
Only Manager type users have the ability to add, edit, or delete users, unless a user profile has this capability assigned to
their profile. Managers may add, edit or delete users with these steps:
Further
information
ADD
CHANGE CODE
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > USERS > ADD
ADD
To add users to the system:
The creator must be user type MANAGER.
1. Scroll to USERS > ADD.
The system generates and displays next available user name.
2. Press SELECT for the default name and number. Or enter a customized user name and press SELECT.
There are different types of users available: STANDARD USER, LIMITED USER, MANAGER or ACCESS.
3. Scroll to the preferred type and press SELECT.
The system generates a default code for each new user.
4. Press SELECT to accept the default code. Or enter a new user code and press SELECT.
The keypad confirms that the new user has been created.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > USERS > CHANGE CODE
CHANGE CODE
To change a code:
1. Scroll to CHANGE CODE and press SELECT.
A randomly generated code appears.
2. Select new code, if acceptable. Or overwrite by entering a new code and press ENTER.
If the system is set for 5-digit codes, a new 5-digit code must be entered. The system will not accept a code with
fewer numbers than it is set to receive
3. Confirm the new code, press SAVE.
4. Press BACK to return to the previous screen to amend the code.
During the process if the display times out, the old code remains valid.
Where USER DURESS feature is enabled, consecutive user codes (i.e. 2906, 2907) are not permitted, as entering
this code from the keypad would activate a user duress event.
Engineer code should be noted. Forgotten codes are be remedied only by a factory default of the system.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > SMS
SMS
The SPC system support SMS communication from the panel to selected users’ mobile phones as well as users being able to
control the SPC system remotely via SMS. These two features work hand in hand as it allows the user to take action using the
SMS control after a SMS notification without the need to be physically at the premises.
SMS control
The SMS control can be set up so that a remote user can send a SMS message to perform the following actions at the panel:
Setting / unsetting
Enable / disable engineer
Enable / disable manufacturer access.
Mapping gate on/off.
SMS events
The SMS notification can be set up to send a range of events that occur on the system such as:
Alarm activation
Confirmed alarms
Fault & tamper
Setting & unsetting
Inhibit & isolate
All other types of events
The SMS notification can operate with a PSTN modem if the PSTN operator supports SMS over PSTN where as
SMS control will need a GSM modem at the panel. A GSM modem will support both SMS notification and control.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > DOOR CONTROL
DOOR CONTROL
This option allows the engineer to control all the doors of the system.
1. Scroll to DOOR CONTROL and press SELECT.
2. Select the door which should be controlled and press SELECT.
3. Select one of the door states listed below as new door state and press SELECT.
NORMAL
The door is in normal operation mode. A card with the corresponding access rights is needed to open the door.
UNLOCKED
The door is unlocked.
LOCKED
The door is locked. Even if a card with the corresponding access rights is presented, the door stays closed.
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
User menus > GRANT ACCESS
GRANT ACCESS
When engineer or manufacturer access has been allowed, the keypad displays the text ENGINEER ENABLE or MANUFACT
ENABLE. Once access has been granted, the user cannot access the system until the engineer has logged off.
To allow engineer access:
1. Scroll to GRANT ACCESS and press SELECT.
2. Select to ALLOW ENGINEER and select ENABLED.
3. To disallow engineer/manufacturer access, follow the same path and toggle to DISABLED and press SELECT.
User types Standard and Manager can access the embedded web server on the SPC . When programming with a browser
interface it is important to remember to click Save to ensure the changes made on the web page are saved on the system. To
view the current programming values on a web page, click Refresh .
User programming can be performed from the browser by entering a valid user ID and password in the logon screen. The User
programming options presented in the browser are also available from the keypad by entering the user password.
New users with unique passwords can be created in Engineer Programming. See page
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Appendix
Appendix
Further
information
User rights
Zone chart
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Appendix > User rights
User rights
Based on the operational features of the SPC system, described below, users have rights attributed to the user profiles.
The installation engineer will inform users of their user rights assigned to each user profile. Depending on how the
system has been programmed, users may have rights to all or some of these features.
User rights
Fullset
Limited
Standard
Manager
The FULLSET operation fully sets the alarm system and provides full protection to a building (opening of any alarm
zones activates the alarm).
On selecting FULLSET, the buzzer sounds and the keypad display counts down the exit time period. Exit the building
before this time period has expired.
When the exit time period has expired, the system is set and opening of entry/exit zones starts the entry timer. If the
system is not Unset before the entry timer expires, the alarm is activated.
Partset A
Standard
Manager
The PARTSET A option provides perimeter protection to a building while allowing free movement through the exit and
access areas.
Zones that have been classified as EXCLUDE A remain unprotected in this mode. By default, there is no exit time; the
system sets instantly on selection of this mode. An exit timer can be applied to this mode by enabling the Partset A
timed variable.
Partset B
Standard
Manager
The PARTSET B option applies protection to all zones except those that have been classified as EXCLUDE B.
By default there is no exit time; the system sets instantly on selection of this mode. An exit timer can be applied to this
mode by enabling the Partset B timed variable.
Forceset
Standard Manager
The FORCESET option is presented on the keypad display when an attempt is made to set the system while an alarm
zone is faulty or still open (the top line of the display shows the open zone).
Selecting this option sets the alarm and inhibits the zone for that set period.
Unset
Limited
Standard
Manager
The UNSET operation unsets the alarm. This menu option is only presented on the keypad after an alarm has been
activated and a valid user code has been entered.
Restore
Standard
Manager
The RESTORE operation restores an alert condition on the system and clears the alert message associated with that alert
condition.
An alert condition can only be restored after the zone(s) or fault(s) that triggered the alert condition have been restored
to their normal operating state and the RESTORE option in user programming is selected for that zone.
Isolate
Standard*
Manager
Isolating a zone deactivates that zone until such time as the zone is de-isolated. All zone types on the SPC can be
isolated.
Use of this feature to deactivate faulty or open zones should be considered carefully; once a zone is isolated, it is ignored
by the system and could be overlooked when setting the system in the future, compromising the security of the premises.
Inhibit
Standard
Manager
Inhibiting a zone deactivates that zone for one alarm set period. Only alarm, entry/exit, fire exit and line zone types can
be inhibited.
This is the preferred method of deactivating a faulty or open zone as the fault or open condition is displayed on the
keypad each time the system is being set to remind the user to attend to that zone.
Change code
Standard
Manager
This menu option allows users to change their user codes .
Engineer
Manager
This option allows users to grant access to manufacturer and engineer programming.
Set Date / Time
Standard
Manager
Use this menu option to program the time and date on the system .
Ensure the time and date information is accurate; these fields are presented in the event log when reporting system
events.
Test
Standard
Manager
This menu option provides the following test features:
1. Bell test : The bell test activates the external bells, strobe, internal bells, and buzzer in turn for 5 seconds to ensure
their correct operation.
2. Walk test: A walk test allows for testing of the operation of all alarm sensors on a system.
When this option is selected, the keypad displays the number of zones to test on the system. Activate each alarm sensor
(by opening the door or window) and check for an audible beep at the keypad. Isolated and inhibited zones are not
included in the walk test.
3. Audible Options: This option allows users to select which devices will activate during the walk test and which will be
silent.
View Log
Standard
Manager
This menu option displays the most recent event on the keypad display. The event log details the time and date of each
logged event.
Chime
Standard
Manager
All zones that have the CHIME attribute set generate a short burst of audible tone on the keypad buzzer when they are
opened (while the system is unset).
This menu option allows for enabling or disabling of the chime feature on all zones.
SMS
Standard*
Manager
This feature allows users to set up the SMS messaging service if a modem is installed on the system.
Users
Manager
User can configure user on the panel.
Delay autoarm
Standard*
Manager
User can delay auto arming.
Upgrade
Manager
User can grant manufacturer access to panel to perform firmware upgrade.
X-10
Standard
Manager
Access Control
User can activate/deactivate configured X-10 devicesDoor Control
Standard*
Manager
Access Control
User can lock/unlock doors.
Web Access
Standard*
Manager
User can access panel through web browser.
* Functions not enabled by default for this user but can be selected.
User Profile
Default
User type
Description
© Siemens Industry - 11-19-2009
SPCK620/623 Comfort Keypad - User Manual
Appendix > Zone chart
Zone chart
Zone #
Description
© Siemens Industry - 11-19-2009