Siemens Gigaset S18H Operating instructions

s
C
M
Y
CM
MY
CY
CMY
K
Issued by
Gigaset Communications GmbH
Schlavenhorst 66, D-46395 Bocholt
Gigaset Communications GmbH is a trademark licensee of Siemens AG
© Gigaset Communications GmbH 2009
All rights reserved.
Subject to availability. Rights of modifications reserved.
www.gigaset.com
Gigaset S18H
Gigaset
S18H / Canada EN / A31008-M1757-R401-1-5819 / AM_overview.fm / 22.6.09
The handset at a glance
The handset at a glance
15
Ð
V
1
2
INT 1
01.31.09 9:45am
Þ
Menu
3
14
13
12
4
5
6
11
7
10
9
8
1 Display in idle status
2 Charge status of the batteries
= e V U (empty to full)
= flashes: batteries almost empty
e V U flashes: batteries charging
3 Display keys (page 15)
4 Message key
Access to calls and message lists;
Flashes: new message
5 Flash key
- Confer (Flash)
- Insert a dialing pause (press and hold)
6 End call key, On/Off key
End call, cancel function, go back one menu
level (press briefly), back to idle status (press
and hold), activate/deactivate handset
(press and hold in idle status)
7 2.5 mm socket for headset (mono)
8 Pound (#) key
Key lock on/off (press and hold in idle status)
Toggle between upper/lower case and digits
9 Microphone
10 Star (*) key
Ringtones on/off (press and hold)
Open table of special characters
11 Key 1
Fast access to answering machine/network
mailbox (press and hold)
12 Talk key
Answer a call, start dialing
13 Handsfree key
Switch between earpiece and handsfree
mode;
Lights up: handsfree activated;
Key flashes: incoming call
14 Control key (page 14)
15 Signal strength
Ð i Ñ Ò (high to low)
| flashes: Out of Range
1
S18H / Canada EN / A31008-M1757-R401-1-5819 / S18HIVZ.fm / 22.6.09
Contents
Contents
Using the network mailbox . . . . 22
........... 3
Configuring the network mailbox
for fast access . . . . . . . . . . . . . . . . . . . 22
Viewing the network mailbox
message . . . . . . . . . . . . . . . . . . . . . . . 22
Notes on the
operating instructions . . . . . . . . . 5
Using a handset as a room
monitor . . . . . . . . . . . . . . . . . . . . 23
The handset at a glance . . . . . . . 1
Safety precautions
Symbols used . . . . . . . . . . . . . . . . . . . . 5
Example: menu input . . . . . . . . . . . . . . 5
Example: multiple line input . . . . . . . . 6
Gigaset S18H –
more than just a telephone . . . . . 7
First Steps . . . . . . . . . . . . . . . . . . . 7
Package contents . . . . . . . . . . . . . . . . . 7
Setting up the charging cradle . . . . . . . 7
Setting up the handset for use . . . . . . . 8
Registering the handset to the
base station . . . . . . . . . . . . . . . . . . . . 10
Initial charging of batteries . . . . . . . . 11
Headset socket . . . . . . . . . . . . . . . . . . 11
Setting the date and time . . . . . . . . . 12
Area codes . . . . . . . . . . . . . . . . . . . . . 12
Display in idle status . . . . . . . . . . . . . . 12
Making calls . . . . . . . . . . . . . . . . 13
Making an external call . . . . . . . . . . .
Ending a call . . . . . . . . . . . . . . . . . . . .
Answering a call . . . . . . . . . . . . . . . . .
Handsfree operation . . . . . . . . . . . . .
Muting . . . . . . . . . . . . . . . . . . . . . . . .
Making internal calls . . . . . . . . . . . . .
13
13
13
13
13
14
Operating the handset . . . . . . . . 14
Control key . . . . . . . . . . . . . . . . . . . . .
Display keys . . . . . . . . . . . . . . . . . . . .
Returning to idle status . . . . . . . . . . .
Menu guidance . . . . . . . . . . . . . . . . .
Correcting incorrect entries . . . . . . . .
Caller ID 2.5 services . . . . . . . . . . . . .
14
15
15
15
15
16
Using the directory and lists . . . 17
Directory . . . . . . . . . . . . . . . . . . . . . . .
Last number redial list . . . . . . . . . . . .
Opening lists with the
message key . . . . . . . . . . . . . . . . . . . .
Writing and editing names . . . . . . . . .
2
17
19
19
20
Handset settings . . . . . . . . . . . . . 24
Changing the display language . . . . .
Setting the display . . . . . . . . . . . . . . .
Setting the screen picture . . . . . . . . . .
Setting lighting . . . . . . . . . . . . . . . . . .
Activating/deactivating
auto answer . . . . . . . . . . . . . . . . . . . .
Adjusting the loudspeaker volume . . .
Changing ringtones . . . . . . . . . . . . . .
Activating/deactivating
advisory tones . . . . . . . . . . . . . . . . . . .
Changing the name of a handset . . . .
Changing a handset's internal
number . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
25
25
26
26
27
27
27
Setting the alarm clock . . . . . . . 28
Restoring the handset
default settings . . . . . . . . . . . . . . . . . . 28
Shortcuts . . . . . . . . . . . . . . . . . . . 29
Appendix . . . . . . . . . . . . . . . . . . . 30
Care . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact with liquid . . . . . . . . . . . . . . .
Questions and answers . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . .
Industry Canada Certification . . . . . . .
Safety precautions . . . . . . . . . . . . . . .
Service (Customer Care) . . . . . . . . . . .
End-user limited warranty . . . . . . . . .
30
30
30
30
31
32
32
34
34
Mounting the charging cradle to
the wall . . . . . . . . . . . . . . . . . . . . 37
Index . . . . . . . . . . . . . . . . . . . . . . 38
S18H / Canada EN / A31008-M1757-R401-1-5819 / security.fm / 22.6.09
Safety precautions
Safety precautions*
$
!
Only use the power supply unit supplied as indicated on the underside of the
device.
Power Outage:
In the event of a power outage, your cordless telephone will not operate. The cordless telephone requires electricity for operation. You should have a telephone that does not
require electricity available for use during power outages.
Only insert approved rechargeable batteries of the same type.
Never use ordinary (non-rechargeable) batteries as they may pose a health
hazard or cause injury.
Do not charge the handset in charging unit while the headset is connected.
‹
Make sure the rechargeable battery is inserted the right way round.
Œ
Use the battery specified in these operating instructions.
The phone may affect medical equipment so always switch your phone off
before entering hospitals or doctors’ practices.
To maintain compliance with the Industry Canada’s RF exposure guideline, place
the base station at least 20 cm from nearby persons
Notice to Hearing Aid Wearers:
This phone is compatible with inductively coupled hearing aids.
Do not operate the phone in places where there is a risk of explosion
(such as paint workshops).
Do not install the charging cradle in bathrooms or shower rooms. The handset
and the charging cradle are not splash-proof (see page 30).
Drivers must not use the phone while driving.
The phone must be switched off at all times in an aircraft. Make sure it cannot
be switched on accidentally.
ƒ
If you give your phone to someone else you should also give them the operating
instructions.
* see also page 32
3
S18H / Canada EN / A31008-M1757-R401-1-5819 / security.fm / 22.6.09
Safety precautions
Dispose of batteries and the phone carefully. Do not pollute the environment.
Privacy of communications may not be ensured when using this telephone.
Emergency numbers cannot be dialed if the keypad lock is activated!
4
S18H / Canada EN / A31008-M1757-R401-1-5819 / notes-on-instructions.fm / 22.6.09
Notes on the operating instructions
Notes on the
operating instructions
This section explains the meaning of certain symbols and typographical conventions that are used in this user guide.
Symbols used
Copy Entry / Copy List (example)
Select one of the two menu
functions specified.
~
Enter digits or letters.
§Save§
The display keys' current functions are shown reverse highlighted in the bottom display
line. Press the display key
below to launch the function.
q
Press the top or the bottom of
the control key: scroll up or
down.
r
Press the right or left of the
control key: for example select
setting.
c / Q / * etc.
Press the corresponding key
on the handset.
Example: menu input
In the user guides, the steps you need to
perform are shown in abbreviated form.
This is illustrated below using the example
of "Setting the contrast for the display".
The things you need to do are explained in
the boxes.
v ¢ Ð ¢ Display
¤ With the handset in idle status, press
on the right of the control key to open
the main menu.
¤ Select the Ð icon using the control key
– press the control key at the top or
bottom.
In the display header, Settings is displayed.
¤ Press the §OK§ display key to confirm the
function Settings .
The Settings submenu is displayed.
¤ Press the bottom of the control key
repeatedly until Display is selected.
¤ Press the §OK§ display key to confirm the
function.
Contrast
Select and press §OK§.
¤ Press the bottom of the control key
repeatedly until Contrast is selected.
¤ Press the §OK§ display key to confirm the
function.
r
Select contrast and press §OK§.
¤ Press on the right or left of the control
key to select the contrast.
¤ Press the §Save§ display key to confirm
the function.
a
Press and hold (idle status).
¤ Press and hold the end call key until the
handset returns to idle status.
5
S18H / Canada EN / A31008-M1757-R401-1-5819 / notes-on-instructions.fm / 22.6.09
Notes on the operating instructions
Example: multiple line input
There are many situations in which you
can change the settings of a display or
enter data in several lines.
In this user guide symbols are used to
guide you step by step through multiple
line input. This is illustrated below using
the example of "Setting the date and
time". The things you need to do are
explained in the boxes.
To change the time, open the input field
with:
v ¢ Ð ¢ Date/Time
You will see the following display
(example):
Date:
12.23.08
Time:
[11:11]am
am/pm
12 h
Save
Date:
Enter month, day and year in 6-digit
format.
The date in the first line is marked with
[ ] to show it is active.
¤ Enter the date using the digit keys.
Time:
Enter hours/minutes in 4-digit format.
¤ Press the s key.
The time in the second line is marked with
[ ] to show it is active.
¤ Enter the date using the digit keys.
6
¤ Press the s key.
The time format is marked with [ ] to
show it is active.
¤ Select time format.
¤ With 12-hour time format, use the display key §am/pm§ to switch between am
and pm.
¤ Save changes.
¤ Press the §Save§ display key.
¤ Then press and hold the a key.
The handset changes to idle status.
Date/Time
Time mode:
Time mode:
Select 12-hour or 24-hour time format.
S18H / Canada EN / A31008-M1757-R401-1-5819 / starting.fm / 22.6.09
Gigaset S18H – more than just a telephone
Gigaset S18H –
more than just a telephone
Your phone not only enables you to store
up to 150 telephone numbers (page 17) –
it can do a whole lot more:
u You can designate important people as
VIPs so you can identify important calls
from the ringtone (page 18).
u You can store anniversary dates
(page 18) in your phone and it will
remind you of them.
u Select frequently used phone numbers
at the press of a single key (page 17).
u View missed calls on your phone
(page 20).
u Select 12 or 24-hour format for displaying the time (page 12).
u ECO DECT reduces power consumption
by using a power supply with low
power consumption. Your handset
reduces the transmitting power
depending on the distance to the base
station (close-up range).
Note:
First Steps
Package contents
u
u
u
u
u
u
u
one handset,
one charging cradle,
one AC adapter for charging cradle,
two batteries,
one battery cover,
one belt clip,
one user guide.
Setting up the charging cradle
The charging cradle is designed to be
operated in enclosed, dry areas at
temperatures ranging from
+5°C to +45°C.
¤ Set up the charging cradles at a central
location on a flat, non-slip surface in
your house or apartment.
For instructions on how to mount the
charging cradle to a wall, please see
page 37.
The transmitting power of the base station is
reduced to almost zero when the handset is
docked and only one handset is registered on
the base station (depending on the base station).
Range and reception strength
Have fun using your new telephone!
Range:
Pay attention to the range of the base
station.
u Up to 300 meters in the open
u Up to 50 meters in buildings
Reception strength:
The display shows the quality of the radio
contact between the base station and
handset:
u Good to poor: Ð i Ñ Ò
u No reception: | flashes
7
S18H / Canada EN / A31008-M1757-R401-1-5819 / starting.fm / 22.6.09
First Steps
Connecting the charging cradle
¤ Connect the power adapter to the wall
outlet ➀.
¤ Connect the power adapter to the base
plug socket ➁.
Please note:
u Never expose the telephone to the
influence of heat sources, direct sunlight or other electrical devices.
u Protect your Gigaset S18H from moisture, dust, corrosive liquids and
vapours.
Setting up the handset for use
Carry out the following steps for each
handset.
➀
Inserting the batteries
➁
If you need to disconnect the plug from
the charging cradle, press the release button ➀ and disconnect the plug ➁.
8
Caution:
Use only rechargeable nickel-metal hydride
(NiMH) UL-approved AAA batteries. Never use
conventional (non-rechargeable) batteries or
other battery types as this may cause significant damage to health and property. For
example, the outer casing of the batteries
could be destroyed or the batteries could
explode. The phone could also malfunction or
be damaged as a result of using batteries that
are not of the recommended type.
¤ Fit the batteries with the correct polar-
ity (see diagram).
The polarity is indicated in/on the battery
compartment.
S18H / Canada EN / A31008-M1757-R401-1-5819 / starting.fm / 22.6.09
First Steps
Closing the battery cover
¤ First align the notches on the side of
¤
the battery cover with the clips on the
inside of the casing.
Then close the cover, press on the top
so that it clicks into place.
Opening the battery cover
¤ If fitted, remove belt clip.
¤ Insert your fingernail into the headset
socket notch and pull the battery cover
upwards.
Attaching the belt clip
There are notches for attaching the belt
clip on the side of the handset just above
the display.
¤ Press the belt clip onto the back of the
handset so that the protrusions on the
belt clip engage with the notches.
9
S18H / Canada EN / A31008-M1757-R401-1-5819 / starting.fm / 22.6.09
First Steps
Registering the handset to the
base station
Before you can use the phone, you must
first register the handset to the base station. The actual registration procedure will
depend on the type of base station.
A Gigaset S18H handset can be registered
on up to four base stations.
The registration can take up to 5 minutes.
During this process, Regstr.Procedure
appears in the display and the name of the
base station flashes, for example Base 1.
When the handset has been registered, its
screen displays its internal number, for
example INT 2 for internal number 2.
Ð
INT 2
Automatic registration: Gigaset S18H
handset to Gigaset S185 base station
Important: The handset must not yet be
registered to any base station.
Registering the handset to the
Gigaset S185 base station occurs automatically.
V
Time
Menu
The handset is assigned the lowest available internal number (1-6). If all internal
numbers 1-6 have been assigned, number
6 is overwritten, assuming that the handset with the internal number 6 is in idle
status.
Note:
– Automatic registration is not possible when
the base station on which you wish to register the handset is being used to make a
call.
– Each key press interrupts the automatic
registration.
– If automatic registration does not work,
you will have to register the handset manually.
– You can change the name of the handset
(page 27).
¤ Place the handset in the base with its
¤
10
display facing outwards.
The handset registers automatically.
Please do NOT remove your handset
from the base station during the registration procedure.
Manual registration:
Gigaset S18H handset
You must activate manual registration of
the handset at both the handset and the
base station.
After it has been registered, the handset
returns to idle status. The internal number
of the handset appears in the display, for
example INT 1. If it does not, repeat the
procedure.
S18H / Canada EN / A31008-M1757-R401-1-5819 / starting.fm / 22.6.09
First Steps
On the handset
v ¢ Ð ¢ Handset ¢ Register H/Set
s
Select base station, for example Base 1 and press §OK§.
~
Enter the system PIN of the
base station (the default is
0000) and press §OK§. The
screen will display the
number, for example Base 1.
On the base station
Within 60 secs. press and hold the registration/paging key on the base station
(approx. 3 secs.).
De-registering handsets
You can de-register any registered handset
from any registered Gigaset S18H handset.
u
Open list of internal users.
The handset you are currently
using is indicated by <.
s
Select the internal user you
wish to de-register.
§Options§
Open menu.
De-reg. H/Set No.
Select and press §OK§.
~
Enter current System PIN and
press §OK§.
§Yes§
Press the display key.
Changing the base station
If your handset is registered to more than
one base station, you can set it to a particular base station or to the base station
that has the best reception (Best Base).
v ¢ Ð ¢ Handset ¢ Select Base
s
Select one of the registered
base stations or Best Base and
press §OK§.
Initial charging of batteries
¤ To charge the batteries, leave the hand-
set in the charging cradle continuously
for ten hours.
The flashing battery icon e in the top
right of the display indicates that the batteries are being charged.
During handset operation, the battery
icon indicates the charge status of the batteries (page 1).
Note:
– If the handset has switched itself off
because the batteries have no charge and is
then placed in the charging cradle, it will
switch itself on automatically.
– Only place the handset in the charging cradle that is intended for it.
For questions and problems see page 30.
Please remember:
u The batteries may feel warm as they are
charging. This is normal.
Headset socket
Which headsets are compatible?
The following headsets have been tested
with the Gigaset S18H:
u Plantronics MX200
u Plantronics MX250
u Top-Nice EP-21-RS (C39453-Z5-C361)
Caution:
Do not charge the handset in charging unit or
base station while the headset is connected.
11
S18H / Canada EN / A31008-M1757-R401-1-5819 / starting.fm / 22.6.09
First Steps
Setting the date and time
¤ To set the date and time, press the dis-
play key §Time§ to open the input menu.
To change the time, open the input field
via:
v ¢ Ð ¢ Date/Time
¤ Change multiple line input:
Date:
Enter month, day and year in 6-digit
format.
Time:
Enter hours and minutes with 4 digits,
e.g. Q M 1 5 for 7:15 am.
If you have selected the 12-hour time format, use the display key §am/pm§ to switch
between am and pm.
Time mode:
Choose between 12 and 24-hour time
format.
§Save§
Press the display key.
Time mode:
Select 12-hour or 24-hour time format.
¤ With 12-hour time format, use the display key §am/pm§ to switch between am
and pm.
¤ Set the date and the time, for example
to ensure the correct time of incoming
calls is recorded.
Area codes
In order to call back a caller using the
incoming caller ID list (page 20), your
phone's area code ("local areas code")
must be stored. If your phone is in a "multiple area code" area, the extra codes for
this area must also be stored.
Please refer to the manual of your base
station.
12
Display in idle status
Once the phone is registered and the time
set, the idle display looks as shown here
(example).
Ð
V
INT 1
01.31.08
Þ
07:15
Menu
Your phone is now ready to use.
S18H / Canada EN / A31008-M1757-R401-1-5819 / telefony.fm / 22.6.09
Making calls
Making calls
Making an external call
External calls are calls using the public
telephone network.
~ c Enter the number and press
the talk key.
Or:
c ~ Press briefly the talk key c
and then enter the number.
In addition to using the talk key c, the
user can initiate the call using the handsfree key d.
To cancel the dialing operation, press the
end call key a.
You are shown the duration of the call
while the call is in progress.
Note:
– Dialing using the directory (page 17) or
calls list (page 20) saves time re-entering
numbers and network provider prefixes
("call-by-call numbers").
Ending a call
a
Press the end call key.
Answering a call
The handset indicates an incoming call in
three ways: by ringing, by a display on the
screen and by the flashing handsfree
key d.
You can accept the call by:
¤ Pressing the talk key c.
¤ Pressing the §Accept§ display key.
¤ Pressing the handsfree key d.
If the handset is in the charging cradle and
the Auto Answer function is activated
(page 25), the call will be answered automatically when you lift the handset from
the charging cradle.
Press the display key §Silence§ to mute the
ringer without answering the call. You can
answer the call as long the call is displayed
on the screen.
Handsfree operation
You can activate the speakerphone at any
time to provide handsfree operation during a call.
Activating/deactivating handsfree
Activating while dialing
~d
¤
Enter the number and press
the handsfree key.
You should inform your caller before
you use the handsfree function so that
they know someone else may be listening.
Switching between earpiece and
handsfree mode
d
Press the handsfree key.
During a call switch handsfree on or off.
If you wish to place the handset in the
charging cradle during a call:
¤ Press and hold the handsfree key d
while placing the handset in the charging cradle. If the handsfree key d
does not light up, press the key again.
For how to adjust the volume, see
page 26.
Muting
You can deactivate the microphone in
your handset during an external call:
Mute
Press the display key on the
left to mute the handset.
Unmute
Press the display key to reactivate the microphone.
13
S18H / Canada EN / A31008-M1757-R401-1-5819 / telefony.fm / 22.6.09
Operating the handset
Making internal calls
Control key
Internal calls to other handsets registered
on the same base station are free.
Calling a specific handset
u
~
Or:
u
s
c
Initiate internal call.
Enter the number of the handset.
Initiate internal call.
Select handset.
Press the talk key.
Calling all handsets ("group call")
u
*
Initiate internal call.
Press the star key. All handsets
are called.
Ending a call
a
Press the end call key.
Operating the handset
Activating/deactivating the handset
a
Press and hold the end call
key. You will hear the confirmation beep.
Activating/deactivating the keypad
lock
#
Press and hold the pound key.
You will hear the confirmation beep. The
icon Ø appears in the display when the
keypad lock is activated.
The keypad lock is deactivated automatically if someone calls you. It is re-activated
when the call is finished.
14
In the description below, the side of the
control key (up, down, right, left) which
you have to press in the different operating situations is marked in black, for
example v for "press right on the control
key".
The control key has a number of different
functions:
When the handset is in idle status
s
v
u
t
Open the directory.
Open main menu.
Open list of handsets.
Set the ringtones on the handset (page 26).
In the main menu and in input fields
You can use the control key to move the
cursor up t, down s, right v or
left u.
In lists and submenus
t/s
v
u
Scroll up/down line by line.
Open submenu or confirm
selection.
Go back one menu level, or
cancel.
During an external call
s
u
t
Open the directory.
Hold with simultaneous internal call.
Adjust loudspeaker volume for
earpiece and handsfree mode.
S18H / Canada EN / A31008-M1757-R401-1-5819 / telefony.fm / 22.6.09
Operating the handset
Display keys
Menu guidance
The function of the display keys changes
depending on the particular operating situation. Example:
Your telephone's functions are accessed
using a menu that has a number of levels.
Þ
Menu
1
2
1 The display keys' current functions are
shown in the bottom display line.
2 Display keys
The most important display symbols are:
§§§§§Menu§§§§
Open the main menu.
§Options§
Open a context-dependent
menu.
W
Delete key: deletes one character at a time from right to
left.
Ó
Copy number into directory.
•
Open the last number redial
list.
Returning to idle status
You can go back to idle status from anywhere in the menu as follows:
¤ Press and hold the end call key a.
Or:
¤ Do not press any key: after 2 minutes
the display will automatically revert to
idle status.
Changes that you have not confirmed or
saved by pressing §OK§, §Yes§, §Save§, §Send§ or
Save Entry §OK§ will be lost.
An example of the display in idle status is
shown on page 12.
Main menu (first menu level)
¤ Press v with the handset in idle status
to open the main menu.
The main menu functions are shown in
the display as a list with icon and name.
To access a function, so that you open the
corresponding submenu (next menu
level):
¤ Navigate to the function using the control key q. Press the display key §OK§.
Submenus
The functions in the submenus are displayed as lists.
To access a function:
¤ Scroll to the function with the control
key q and press §OK§.
Or:
¤ Enter the corresponding shortcut digit
combination (page 29).
Pressing briefly on the end call key a
returns you to the previous menu level /
cancels the operation.
Correcting incorrect entries
You can correct incorrect characters in the
text by navigating to the incorrect entry
using the control key. You can then:
u press X to delete the character to the
left of the cursor,
u insert characters to the left of the cursor,
u overwrite the (flashing) character
when entering the time and date etc.
You will find examples of symbols used,
menu entries and multiple line input in the
"Notes on the operating instructions",
page 5.
15
S18H / Canada EN / A31008-M1757-R401-1-5819 / telefony.fm / 22.6.09
Operating the handset
Caller ID 2.5 services
If CID is activated and a waiting call is displayed, 4 different CID 2.5 services (network services) are selected.
During a call:
§Options§
Press the display key
Select with q:
TAKE MSG
The waiting caller is forwarded to the
central office mailbox.
HOLD MSG
The waiting caller is put on hold and
hears a message to this effect from the
central office.
CALL BACK
The waiting caller is prompted by the
central office to call again at a later
time.
ADD 2ND
The central office is prompted to initiate a conference call.
Note:
When the handset is muted and ADD 2ND
selected, the microphone will be automatically
unmuted.
16
S18H / Canada EN / A31008-M1757-R401-1-5819 / direct_charges.fm / 22.6.09
Using the directory and lists
Using the directory and lists
The options are:
u Directory,
u Last number redial list,
u Calls list,
u Answering machine list (depending on
the base station).
You can store a maximum of 150 entries in
the directory (the actual number depends
on the size of the individual entries).
You create the directory for your own individual handset. You can also send lists/
entries to other handsets (page 18).
Directory
In the directory, you can store numbers
and names associated with them.
¤ With the handset in idle status, open
the directory by pressing the s key.
Length of entries
Number:
Name:
max. 32 digits
max. 16 characters
Note:
For one-touch quick access to a number from
the directory, you can assign the number to a
key (see Speed Dial below).
Storing a number in the directory
s ¢ New Entry
¤ Change multiple line input:
Number:
Enter number.
Name:
Enter name.
Annivers.:
Enter anniversary if required (page 18).
Speed Dial:
Select key for quick dial.
¤ Save changes.
Selecting entries in the directory
s
Open directory.
You have the following options:
u Use s to scroll through the entries
until the required name is selected.
u Enter the first character of the name, or
scroll to the entry with s if required.
Dialing with the directory
s ¢ s (select entry)
c
Press the talk key. The number
is dialed.
Managing entries in the directory
s
¢ s (select entry)
Viewing an entry
§View§
Press the display key.
The entry is displayed.
Back with §OK§.
Editing entries
Press display keys one after the
other.
Carry out changes and save.
§View§ §Edit§
¤
Using other functions
s ¢ s (select entry)
¢ §Options§ (open menu)
The following functions can be selected
with q:
Display Number
Edit or complete a stored number. Then
dial or copy the number to the directory
by pressing Ó.
Edit Entry
Edit selected entry.
Delete Entry
Delete selected entry.
17
S18H / Canada EN / A31008-M1757-R401-1-5819 / direct_charges.fm / 22.6.09
Using the directory and lists
VIP Entry (directory only)
Mark a directory entry as VIP
(Very Important Person) and assign it
a particular ringtone. You can then
identify VIP calls by their ringtones.
Requirement: Caller ID.
Copy Entry
Send a single entry to a handset
(page 18).
Delete List
Delete all entries in the directory.
Copy List
Send complete list to a handset
(page 18).
Available Memory
Display the available entries in the
directory (page 17).
Please remember:
Using quick dial keys
§Options§
¤ Press and hold the required quick dial
key (page 17).
Sending the directory to another
handset
Requirements:
u The sending and receiving handsets
must both be registered to the same
base station.
u The other handset and base station can
send and receive directory entries.
s ¢ s (select entry)
¢ §Options§ (open menu)
¢ Copy Entry / Copy List
~
Enter the internal number of
the receiver handset. You see
Copying entry.
§Yes§ / §No§
Press the display key.
A successful transfer is confirmed by a
message and confirmation tone on the
receiver handset.
18
u Entries with identical numbers are not
overwritten on the receiver handset.
u The transfer is canceled if the phone
rings or if the memory of the receiver
handset is full.
Adding a displayed number to the
directory
Numbers that appear in a list such as the
calls list or the last number redial list, or
displayed during a call can be added to the
directory.
If you have Caller ID/Name, the first
16 characters of the transmitted name are
copied to the Name line.
A number is displayed:
¢ Copy to Directory
¤ Complete the entry, see page 17.
Copying a number from the directory
There are many operating situations in
which you can open the directory, such as
copying a number. Your handset need not
be in idle status.
¤ Depending on the operating situation,
open the directory with s or Ó.
q
Select an entry (page 17).
Storing anniversaries in the directory
You can store an anniversary for every
number in the directory and specify a time
when you will receive a reminder call on
the anniversary.
s ¢ s (Select entry; page 17)
§View§ §Edit§ Press display keys one after the
other.
s
Scroll to the Annivers.: line.
§Edit§
Press the display key.
¤ Change multiple line input:
Date:
Enter the month/day in 4-digit format.
S18H / Canada EN / A31008-M1757-R401-1-5819 / direct_charges.fm / 22.6.09
Using the directory and lists
Time:
Enter the hour/minute for the reminder
call in 4-digit format.
Prompt:
Select the type of signal for the
reminder and press §OK§.
¤ Save changes (page 6).
Note:
Reminder calls require a time stamp. If you
select a visual signal, then a time stamp is not
required and is automatically set to 12:00 a.m.
Deleting anniversaries
s
¢ s (Select entry; page 17)
§View§ §Edit§
s
Press display keys one after the
other.
Scroll to the Annivers.: line.
§Edit§ §Delete§ §Save§
Press display keys one after the
other.
Reminder call on an anniversary
A reminder call is signaled on the handset
using the selected ring tone.
§OFF§
Press the display key to stop
the reminder call.
Last number redial list
The last number redial list contains the ten
numbers last dialed with the handset
(max. 32 digits). If one of the numbers is
in the directory, then the corresponding
name will be displayed.
Manual last number redial
•
s
c
Press the display key.
Select entry.
Press the talk key.
The number is dialed.
When displaying a name, you can have the
respective phone number displayed by
using the display key §View§.
Managing entries in the last number
redial list
•
Press the display key.
Select entry.
§Options§§
Open menu.
The following functions can be selected
with q:
Display Number (as in the directory,
page 17)
Copy to Directory
Copy an entry to the directory
(page 18)
Delete Entry (as in the directory, page 17)
Delete List (as in the directory, page 18)
s
Opening lists with the
message key
The message key will flash if a caller left a
voice mail message. You can use the message key f to open the following lists:
u Answering machine list (depending on
the base station).
u Network mailbox
If your network provider supports this
function and the network mailbox is
configured for fast access (page 22).
u Calls list
An advisory tone sounds as soon as a new
entry appears on a list. The f key
flashes (it will go off when the key is
pressed). In idle status, the display shows
an icon for the new entry.
Icon
Ã
Á
New entry...
... in answering machine list
(depending on the base station)
or network mailbox
... in calls list
The number of new entries is shown
beneath the corresponding icon.
19
S18H / Canada EN / A31008-M1757-R401-1-5819 / direct_charges.fm / 22.6.09
Using the directory and lists
Only the lists that contain messages are
shown (exception: network mailbox). Lists
with new messages are shown first and
identified in bold. The number of new or
old messages contained are each shown
in brackets.
Select the list with q. To open, press §OK§.
Note:
The answering machine, network mailbox,
and/or calls list can only be active on one handset at a time.
Calls list
Requirement: Caller ID Presentation (CIP)
The numbers of the last 30 incoming calls
are stored.
Setting list type for calls list
v ¢ Ð ¢ Base ¢ Calls List Type
Missed Calls / All Calls
Select and press §OK§ ( ‰ = on).
a
Press and hold (idle status).
The entries in the calls list are retained
when you change the list type.
List entry
New messages are at the top.
Example of list entries:
All Calls
J. Smith
5555551234
01.29.09
11:15 am
‰
Delete
Options
u List type (in header)
u Status of entry
u Number and name of caller
You can add the number of the caller to
the directory (page 18)
u Date and time of call (if set, page 12)
u Type of entry
according to list type All Calls:
20
– accepted calls ( ‰ )
– missed calls
– calls recorded by the answering
machine (Ã depending on the
base station)
according to list type Missed Calls:
– missed calls (if [3] is displayed: 3rd
entry in the list)
Pressing the display key §Delete§ deletes the
marked entry.
After pressing the display key §Options§ you
can select more functions with q:
Copy to Directory
Add a number to the directory.
Information
Complete caller information is displayed.
Delete Calls List
Delete complete list.
When you leave the calls list all entries are
set to the status "old", so that the next
time you call up the list they will no longer
be shown in bold.
Answering machine list (depending on
the base station)
You can use the answering machine list
to listen to the messages that are on the
answering machine.
Writing and editing names
The following rules apply when creating
an entry:
u Control the cursor with u v t s.
u Characters are added to the left of the
cursor.
u Press the star key * to show the
table of special characters.
u Press and hold the pound key # to
switch from "Abc" mode to "123" and
from "123" to "abc" and from "abc" to
"Abc" (upper case: 1st letter upper
case, all others lower case). Press the
pound key # before entering the
letter.
S18H / Canada EN / A31008-M1757-R401-1-5819 / direct_charges.fm / 22.6.09
Using the directory and lists
u The first letter of the name of directory
entries is automatically capitalized, followed by lower case letters.
Entering special characters
You can call up the table of special characters using the * key. Select the
required character and insert it with §Insert§.
Order of directory entries
Directory entries are usually sorted in
alphabetical order. Spaces and digits take
first priority. The sort order is as follows:
1. Space
2. Digits (0–9)
3. Letters (alphabetical)
4. Other characters
To get around the alphabetical ordering of
the entries, insert a space or a digit in
front of the name. These entries will then
move to the beginning of the directory.
Names which you have preceded with an
asterisk will move to the end of the directory.
21
S18H / Canada EN / A31008-M1757-R401-1-5819 / T-NetBox_SAG.fm / 22.6.09
Using the network mailbox
Using the network mailbox
Calling the network mailbox
The network mailbox is your network provider's answering machine within the network. You cannot use the network mailbox unless you have requested it from
your network provider.
d
1
Press and hold.
You are connected directly to
the network mailbox.
Press handsfree key d if
required. You hear the network mailbox announcement.
Configuring the network mailbox
for fast access
Viewing the network mailbox
message
With fast access, you can dial the network
mailbox directly.
If a message arrives for you, you receive a
call from the network mailbox. If you have
requested Caller ID, the display shows the
network mailbox number. If you accept
the call, the new messages are played
back. If you do not accept the call, the network mailbox number will be stored in the
missed calls list and the message key will
flash (page 19).
Configuring the network mailbox for fast
access and entering the network mailbox
number
v ¢ Ð ¢ Voice Mail ¢ Set Key 1 ¢
Network Mailb.
Select and press §OK§ ( ‰ = on).
~
Enter the number for the
network mailbox.
Save§
Press the display key to save
the input.
a
Press and hold (idle status).
The setting for fast access applies to all
Gigaset S18H handsets.
If your network mailbox requires a password for access, it is possible to add this
password by entering pauses (see Flash
key on page 1) immediately after the mailbox access number, then enter your password.
Your telephone will dial the mailbox
number, wait a few seconds until the mailbox is accessed, then dial your password.
If more time is needed for your mailbox to
answer before the network mailbox password is dialed, simply add an additional
pause (P).
22
S18H / Canada EN / A31008-M1757-R401-1-5819 / registr_sett.fm / 22.6.09
Using a handset as a room monitor
Using a handset as a room
monitor
If the room monitor is activated, a previously stored destination number is called
as soon as a set noise level is reached. You
can store an internal or external number
in your handset as the destination
number.
The room monitor call to an external
number stops after approx. 90 seconds.
The room monitor call to an internal
number (handset) stops after approx.
3 minutes (depending on the base station). While the room monitor is activated,
all keys are locked except the end call key.
The handset's speaker is muted.
When the room monitor is activated,
incoming calls to the handset are indicated without a ringtone and are only
shown on the screen. The display and keypad are not illuminated and advisory
tones are also turned off.
If you accept an incoming call, the room
monitor mode is suspended for the duration of the call, but the function remains
activated.
If you switch off the handset, the room
monitor mode is deactivated. You will
need to reactivate the function after
switching on the handset again.
Caution:
– You should always check the operation
of the room monitor before use. For
example, test its sensitivity. Check the
connection if you are diverting the room
monitor to an outside number.
– When the function is switched on the handset's operating time is severely reduced. If
necessary, place the handset in the charging cradle. This ensures that the batteries
do not run down.
– Ideally the handset should be positioned
1 to 2 meters away from the sound being
monitored. The microphone must be
directed towards the monitored sound.
– The connection to which the room monitor
is diverted must not be blocked by an activated answering machine.
Activating the room monitor and
entering the number to be called
v ¢ í ¢ Room Monitor
¤ Change multiple line input:
Room M.:
Select On to activate.
Call to:
Press the display key §Edit§ and enter destination number.
External number: select number from
the directory or enter directly. Only the
last 4 digits are displayed.
Internal number: delete any stored
external number. §INT§ s (select handset or Call All, if all registered handsets
are to be called) §OK§.
Store number with §Save§.
Level:
Set noise level sensitivity (Low or High).
¤ Save changes (page 6).
The function is now activated. With
Options, you can move directly to settings.
23
S18H / Canada EN / A31008-M1757-R401-1-5819 / registr_sett.fm / 22.6.09
Handset settings
Changing previously set external
destination number
v ¢ í ¢ Room Monitor
s
Scroll to the Call to: line.
§Edit§
Press the display key.
X
Delete existing number.
¤ Enter number as described in "Activating the room monitor and entering the
number to be called" (page 23).
¤ Save changes (page 6).
Changing previously set internal
destination number
v ¢ í ¢ Room Monitor
s
Scroll to the Call to: line.
§Edit§
Press the display key.
§Yes§
Press the display key to confirm the prompt.
¤ Enter number as described in "Activating the room monitor and entering the
number to be called" (page 23).
¤ Save changes (page 6).
Deactivating the room monitor
remotely
Important: The destination phone must
support touch tone dialing and the room
monitor must be set for an external destination number.
¤ Take the call from the room monitor
and press keys 9 ;.
The external caller will hear a deactivation
signal tone and then the call will end.
There will be no further room monitor
calls. But the other room monitor settings
on the handset (such as no ringtone) will
remain activated until you press the display key §OFF§ on the handset.
To reactivate the room function with the
same phone number:
¤ Turn on the activation again and save
(page 23) with §Save§.
24
Handset settings
Your handset is preconfigured, but you
can change these settings to suit your
individual requirements.
Changing the display language
You can view the display texts in different
languages.
v ¢ Ð ¢ Handset ¢ Language
The current language is indicated by ‰ .
s
Select a language and
press §OK§.
a
Press and hold (idle status).
If you accidentally choose a language you
do not understand:
v 5 41
Press display keys one after the
other.
s
Select the correct language
and press §OK§.
Setting the display
You have a choice of four color schemes
and several different contrasts.
v ¢ Ð ¢ Display ¢ Color Scheme
Select and press §OK§.
s
Select a color scheme and
press §OK§ ( ‰ = current color).
a
Press briefly.
s
Scroll to the Contrast line.
Contrast
Select and press §OK§.
r
Select contrast.
§Save§
Press the display key.
a
Press and hold (idle status).
S18H / Canada EN / A31008-M1757-R401-1-5819 / registr_sett.fm / 22.6.09
Handset settings
Setting the screen picture
Setting lighting
You can display a screen picture (picture or
digital clock) when the handset is in idle
status. This will replace the idle status display. It may conceal the date, time and
name.
The screen picture is not displayed in certain situations, e.g. during a call or when
the handset has been de-registered.
If a screen picture has been activated,
the menu item Screen Saver is marked
with ‰ .
v ¢ Ð ¢ Display ¢ Screen Saver
The current setting is displayed.
¤ Change multiple line input:
Activation:
Select On (screen picture is displayed)
or Off (no screen picture).
Selection:
Change screen picture if necessary (see
below).
¤ Save changes.
If the screen picture conceals the display,
press the end call key briefly to show the
idle display with time and date.
Depending on whether or not the handset
is in the charging cradle you can set different levels of lighting. If it is switched on,
the display is permanently dimmed.
v ¢ Ð ¢ Display ¢ Backlight
The current setting is displayed.
¤ Change multiple line input:
In Charger
Select On or Off.
without Charger
Select On or Off.
§Save§
Press the display key.
a
Press and hold (idle status).
Changing the screen picture
v ¢ Ð ¢ Display ¢ Screen Saver
s
Scroll to the Selection line.
§View§
Press the display key.
The active screen picture
is displayed
s
Select picture/Clock.
§Save§
Press the display key.
¤ Save changes.
Note:
When the lighting is switched on, the standby
time of the handset is reduced to approx. 30
hours.
Activating/deactivating
auto answer
If you have activated this function, when
you get a call you can simply lift the handset out of the charging cradle without having to press the talk key c.
v ¢ Ð ¢ Handset
Auto Answer
Select and press §OK§ ( ‰ = on).
a
Press and hold (idle status).
25
S18H / Canada EN / A31008-M1757-R401-1-5819 / registr_sett.fm / 22.6.09
Handset settings
Adjusting the loudspeaker
volume
You can set the loudspeaker volume for
handsfree speaking to five different levels
and the earpiece volume to three different
levels. You can only make these adjustments during a call.
The handsfree volume can only be
adjusted with this procedure.
You are conducting an external call.
t
Open menu.
r
Select volume.
§Save§
Press display key if necessary
to save the setting permanently.
If t is assigned a different function,
e.g. when toggling (page 16):
§Options§
Open menu.
Volume
Select and press §OK§.
Configure setting (see above).
Changing ringtones
u Volume:
You can choose between five volumes
(1–5; e.g. volume 2 = ˆ) and
the "Crescendo" ring (6; volume
increases with each ring =
‰).
u Ringtones:
You can choose between 15 different
melodies.
You can configure the following functions
with different ringtones:
u Ext. Calls: for external calls
u Internal Calls: for internal calls
u All: the same for all functions
Settings for individual functions
Set the volume and melody depending on
the type of signaling required.
v ¢ Ð ¢ Audio Settings
¢ Ringer Settings
q
Set, for example select
Ext. Calls and press §OK§.
¤ Change multiple line input:
r
Set volume (1–6).
s
Scroll to the next line.
r
Select melody.
§Save§
Press the display key.
In idle status, you can also open the menu
Ringer Settings by pressing t briefly.
Settings for all functions to ring the
same
v ¢ Ð ¢ Audio Settings
¢ Ringer Settings ¢ All
¤ Set volume and ringtone (see "Settings
for individual functions").
§Save§
Press the display key.
a
Press and hold (idle status).
Activating/deactivating the ringtone
You can deactivate the ringtone on your
handset before you answer a call or when
the handset is in idle status; the ringtone
can be deactivated permanently or just for
the current call. The ringtone cannot be
re-activated while an external call is in
progress.
Deactivating the ringtone permanently
*
Press the star key and hold
until you can no longer hear
the ringtone.
The Ú icon appears in the display.
Re-activating the ringtone
*
26
Press and hold the star key.
S18H / Canada EN / A31008-M1757-R401-1-5819 / registr_sett.fm / 22.6.09
Handset settings
Deactivating the ringtone for the
current call
§Silence§
Press the display key.
Activating/deactivating the alert tone
You can activate an alert tone in place of a
ringtone. When you get a call, you will
hear a short tone ("Beep") instead of the
ringtone.
*
Press and hold the star key
and within 3 seconds:
§Beep§§
Press the display key. A call is
now signaled by one brief
alert tone. You will now see
º in the display.
Activating/deactivating
advisory tones
Your handset uses 'advisory tones' to tell
you about different activities and statuses.
The following advisory tones can be activated and deactivated independently of
each other:
u Key beep: Each key press is acknowledged.
u Acknowledge tones:
– Confirmation tone (ascending tone
sequence): at the end of an entry/
setting and when a new entry
arrives in calls list
– Error beep (descending tone
sequence): when you make an
incorrect entry
– Menu end tone: when scrolling at
the end of a menu
u Battery tone: The batteries need to be
charged.
v ¢ Ð ¢ Audio Settings
¢ Advisory Tones
¤ Change multiple line input:
Key Tones:
Select On or Off.
Confirm.:
Select On or Off.
Battery:
Select On, Off or In Call. The battery
warning tone is activated/deactivated
or only sounds during a call.
¤ Save changes (page 6).
You cannot deactivate the confirmation
tone for placing the handset in the charging cradle.
Changing the name of a handset
The names "INT 1", "INT 2" etc. are
assigned automatically at registration.
You can change these names. The name
must be no more than 10 characters. The
changed name is displayed in every handset's list.
u
Open list of handsets. Your
own handset is indicated by <.
s
Select handset.
§Edit§
Press the display key.
~
Enter name.
§Save§
Press the display key.
Changing a handset's internal
number
A handset is automatically assigned the
lowest unassigned number when it is registered. If all the numbers have been
assigned, number 6 is overwritten, assuming the handset is in idle status. You can
change the internal number of all registered handsets (1–6).
u
Open list of handsets. Your
own handset is indicated by <.
§Options§
Open menu.
Edit H/Set No.
Select and press §OK§. The list of
handsets is displayed.
s
The current number flashes.
Select a handset.
~
Enter the new internal number
(1–6). The handset's old
number is overwritten.
27
S18H / Canada EN / A31008-M1757-R401-1-5819 / registr_sett.fm / 22.6.09
Setting the alarm clock
Press the display key to save
the input.
a
Press and hold (idle status).
You will hear the error tone (descending
tone sequence) if you assign an internal
number twice.
¤ Repeat the process with an unused
number.
§Save§
Setting the alarm clock
Requirement: The date and time have
already been set (page 12).
Activating/deactivating and setting the
alarm clock
v¢ì
¤ Change multiple line input:
Activation:
Select On or Off.
Time:
Enter the wake-up time in 4-digit
format. Select 12-hour or 24-hour time
format.
¤ With 12-hour time format, use the display key §am/pm to switch between am
and pm.
Melody:
Select melody.
Volume:
Set the volume (1-6).
¤ Save changes (page 6).
You will see the icon ¼.
A wake-up call with the selected ringer
melody is signaled on the handset. The
wake up call sounds for 60 seconds. The
display shows Alarm Clock . If no key is
pressed the wake-up call is repeated twice
at five minute intervals and then switched
off.
During a call, the wake-up call is signaled
by a short tone.
28
Deactivating the wake-up call/
repeating after a pause (sleep mode)
Requirement: A wake-up call is sounding.
§OFF§
Press the display key. The
wake-up call is deactivated.
Or:
§Snooze§
Press the display key or any
key. The wake-up call is deactivated and then repeated after
5 minutes. After the second
repetition the wake-up call is
deactivated completely.
Restoring the handset
default settings
You can reset any individual settings and
changes you have made. This will not
affect entries in the directory, calls list or
the handset's registration to the base station.
v ¢ Ð ¢ Handset ¢ Reset Handset
§Yes§
Press the display key.
a
Press and hold (idle status).
Cancel the restoring process by pressing
a or the display key §No§.
S18H / Canada EN / A31008-M1757-R401-1-5819 / menuetree.fm / 22.6.09
Shortcuts
Shortcuts
Instead of scrolling to locate a menu function, you can select a menu function more
quickly by opening the menu and keying in the digit combination ("shortcut").
Example: v 5 2 1 1 for "Set ringtone for external calls".
With the telephone in idle status, press v (open main menu):
3
Alarm Clock ì
4
Add. Features í
4-3
Room Monitor
5
Settings Ð
5-1
Date/Time
5-2
Audio Settings
5-3
5-4
Display
Handset
(page 23)
5-2-1
Ringer Settings
(page 26)
5-2-2
Advisory Tones
(page 27)
5-3-1
Screen Saver
(page 25)
5-3-2
Color Scheme
(page 24)
5-3-3
Contrast
(page 24)
5-3-4
Backlight
(page 25)
5-4-1
Language
(page 24)
5-4-2
Auto Answer
(page 25)
5-4-3
Register H/Set
(page 10)
5-4-4
Select Base
(page 11)
5-4-5
Reset Handset
(page 28)
5-5
Base
(Menu dependent on base station)
5-6
Voice Mail
(Menu dependent on base station)
29
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
Appendix
Troubleshooting
The display is blank.
Care
¤ Wipe the charging cradle and handset
with a damp cloth (do not use solvent)
or an antistatic cloth.
Never use a dry cloth. This can cause
static.
Contact with liquid
!
If the handset has come into contact with
liquid:
1. Switch the handset off and remove
the batteries immediately.
2. Allow the liquid to drain from the handset.
3. Pat all parts dry, then place the handset
with the battery compartment open
and the keypad facing down in a dry,
warm place for at least 72 hours (not
in a microwave, oven etc.).
4. Do not switch on the handset again
until it is completely dry.
When it has fully dried out, you will normally be able to use it again.
Questions and answers
If you have any questions about the use of
your telephone, you can contact us at any
time at
www.gigaset.com/customercare.
The table below (page 30) contains a list
of common problems and possible solutions.
1. The handset is not switched on.
Press a and hold the end call key.
¥
2. The batteries are empty.
Charge or replace the batteries
(page 11).
¥
The handset does not respond to a key press.
The keypad lock is activated.
Press and hold the pound key #
(page 14).
¥
"Base station x" is flashing in the display.
1. The handset is outside the range of the base
station.
Reduce the distance between handset/
base station.
¥
2. The handset has been de-registered.
Register the handset (page 10).
¥
3. The base station is not switched on.
Check the base station power adapter.
¥
Base Search is flashing in the display.
The handset is set for Best Base and no base station is switched on or within range.
Reduce the distance between handset/base
station.
Check the base station power adapter.
¥
¥
Handset does not ring.
The ringtone is switched off.
Activate the ringtone (page 26).
¥
The other party cannot hear you.
1. You have pressed the u (INT) key.
Take the external caller off hold by ending the internal call (page 14).
¥
2. The handset is muted.
Switch on the microphone again
(page 13).
¥
The incoming call number is not displayed
although CIP is set.
Caller ID is not enabled.
The user must ask the telephone network
provider to activate Caller ID (CID).
¥
30
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
You hear an error tone when keying an input
(a descending sequence of tones).
Action has failed/invalid input.
Repeat the operation.
Watch the display and refer to the operating
instructions if necessary.
¥
General specifications
DECT 6.0
is supported
No. of channels
30 duplex channels
Radio frequency
range
1920 – 1930 MHz
You cannot listen to messages on the network mailbox.
Duplex method
Time multiplex,
10 ms frame length
¥
Your phone system is set for pulse dialing.
Set your phone system to tone dialing.
Channel grid
1728 kHz
Bit rate
1152 kbit/s
Specifications
Modulation
GFSK
Language code
32 kbit/s
Recommended batteries
Transmission
power
10 mW, average power per
channel
Nickel-metal hydride (NiMH):
The handset is supplied with UL-approved
AAA batteries.
Range
up to 300 meters outdoors, up to 50 meters
indoors
Warning:
Only use UL-approved nickel-metal-hydride
(NiMH) batteries in the handset; do not use
non-rechargeable batteries.
Handset operating times/charging
times
Capacity
650 mAh
Standby time
Approx. 170 hours (7 days)
Calling time
Approx. 13 hours
Charging time
approx. 6 hours
Power supply
unit
110 V ~/60 Hz
Environmental
conditions for
operation
+5°C to +45°C;
20 % to 75 % relative
humidity
Dialing mode
DTMF (tone dialing)/
DP (pulse dialing)
The operating and charging times apply
only when using the recommended batteries.
Note:
When the lighting is switched on, the standby
time of the handset is reduced to approx. 30
hours.
31
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
Industry Canada Certification
Safety precautions
Operation is subject to the following two conditions (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
NOTICE: The Industry Canada label identifies
certified equipment. This certification means
that the equipment meets certain telecommunications network, protective, operational and
safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the
user’s satisfaction.
Before installing this equipment, users should
ensure that it is permissible to be connected to
the facilities of the local telecommunications
company. The equipment must also be installed
using an acceptable method of connection. The
customer should be aware that compliance
with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect
the equipment.
Users should ensure for their own protection
that the electrical ground connections of the
power utility, telephone lines and internal
metallic water pipe system, if present, are
connected together.
This precaution may be particularly important
in rural areas
NOTE: Users should not attempt to make such
connections themselves, but should contact
the appropriate electric inspection authority,
or electrician, as appropriate.
This product meets the applicable Industry
Canada technical specifications.
Before using your telephone equipment, basic
safety instructions should always be followed to
reduce the risk of fire, electric shock and injury
to persons.
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. Unplug this product from the wall telephone
jack and power outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use
damp cloth for cleaning.
4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or
laundry tub, in a wet basement or near a swimming pool.
5. Place this product securely on a stable surface. Serious damage and/or injury may result if
the unit falls.
6. Slots or openings in the cabinet and the back
and bottom are provided for ventilation, to protect it from overheating. These openings must
not be blocked or covered. This product should
never be placed near or over a radiator or heat
register, or in a place where proper ventilation
is not provided.
7. This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type of
AC line power to your home, consult your
dealer or local power company.
8. Do not place objects on the power cord.
Install the unit where no one can step or trip on
the cord.
9. Do not overload wall outlets and extension
cords as this can result in the risk of fire or electric shock.
10. Never push objects of any kind into this
product through cabinet slots as they may
touch dangerous voltage points or short out
parts that could result in the risk of fire or electric shock. Never spill liquid of any kind on this
product.
11. To reduce the risk of electric shock or burns,
do not disassemble this product. Take it to a
qualified service center when service is
required. Opening or removing covers may
expose you to dangerous voltages, dangerous
electrical current or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.
12. Unplug the product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
a.) When the power cord is damaged or frayed.
b.) If liquid has been spilled into the product.
c.) If the product has been exposed to rain or
water.
The Ringer Equivalence Number is an indication
of the maximum number of devices allowed to
be connected to a telephone interface. The termination of an interface may consist of any
combination of devices subject only to the
requirement that the sum of the RENs of all
devices does not exceed five.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
32
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
d.) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions because improper adjustment of
other controls may result in damage and may
require extensive work by a qualified technician
to restore the product to normal operation.
e.) If the product has been dropped or physically has been damaged.
f.) If the product exhibits a distinct change in
performance.
13. Avoid using a telephone (other than a cordless type) during a thunderstorm. There may be
a remote risk of electrical shock from lightning.
Therefore we suggest a surge arrestor.
14. Do not use the telephone to report a gas
leak in the vicinity of the leak.
15. Emergency/911 numbers may not be dialed
if the keypad is locked.
BATTERY SAFETY PRECAUTIONS
To reduce the risk of fire, injury or electric
shock, and to properly dispose of batteries,
please read and understand the following
instructions.
CONTAINS NICKEL METAL HYDRIDE BATTERY.
BATTERY MUST BE RECYCLED OR DISPOSED OF
PROPERLY. DO NOT DISPOSE OF IN MUNICIPAL
WASTE.
1. Only use the batteries specified for use with
this product.
2. DO NOT USE NICKEL CADMIUM OR LITHIUM
BATTERIES, or mix batteries of different sizes or
from different manufacturers in this product.
DO NOT USE NONRECHARGEABLE BATTERIES.
3. Do not dispose of the batteries in a fire; the
cells may explode. Do not expose batteries to
water. Check with local codes for special disposal instructions.
4. Do not open or mutilate the batteries.
Released electrolyte is corrosive and may cause
damage to the eyes or skin. The electrolyte may
be toxic if swallowed.
5. Exercise care in handling the batteries in
order not to short the batteries with conducting
materials such as rings, bracelets, and keys. The
batteries or conducting material may overheat
and cause burns or fire.
6. Charge the batteries provided with, or identified for use with, this product only in accordance with the instructions and limitations specified in the user’s manual. Do not attempt to
charge the batteries with any means other than
that specified in the users manual.
7. Periodically clean the charge contacts on
both the charger and handset.
33
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
Service (Customer Care)
Customer Care Warranty for Cordless Products
To obtain Customer Care Warranty service,
product operation information, or for problem resolution, call:
Toll Free: 1-866-247-8758
www.gigaset.com/customercare
End-user limited warranty
This product is covered by a one year limited
warranty. Any repair replacement or warranty
service, and all questions about this product
should be directed to: 1-866-247-8758.
–
This limited, non-transferable warranty is provided to the original buyer/end-consumer
("you") for systems, handsets and accessories
(collectively, "Product") provided by Gigaset
Communications USA LLC or Gigaset Communications Canada Inc. (collectively "Gigaset
NAM"). Gigaset NAM warrants to you that at
the date of purchase, the Product is free of
defects in workmanship and materials and the
software included in the Product will perform in
substantial compliance to its program specifications.
–
1. WARRANTY PERIOD
–
–
–
The Product warranty period is one (1) year
from the original date of purchase by you. Proof
of purchase (e.g., sales slip or invoice) must be
provided with any Product returned during the
warranty period. Batteries supplied with the
Products are warranted to be free from defects
at the time of purchase only.
2. EXCLUSIVE REMEDY
Gigaset NAM's entire liability and your exclusive
remedy if the Product is defective in materials
or workmanship during the warranty period
and is returned shall be that the Product will be
repaired or replaced as set forth in Section 4
below. Reconditioned replacement components, parts or materials may be used in the
replacement or repair. Data in the memory of
the Product may be lost during repair.
3. THIS LIMITED WARRANTY DOES NOT
COVER AND IS VOID WITH RESPECT TO
THE FOLLOWING:
– Cosmetic damage, physical damage to the
surface of the Product, including, without
limitation, breakage, cracks, dents,
34
–
scratches or adhesive marks on the LCD
screen or outside casing of the Product.
Products which have been repaired, maintained or modified (including the antenna)
by anyone other than Gigaset NAM or a
Gigaset NAM-approved repair facility, or
that have been improperly installed.
Cost of installation, removal or reinstallation.
Damage due to any telephone, electronic,
hardware or software program, network,
Internet or computer malfunctions, failures,
or difficulties of any kind, including without
limitation, server failure or incomplete,
incorrect, garbled or delayed computer
transmissions.
Equipment and components not manufactured, supplied or authorized by Gigaset
NAM.
Modification of the Product's components,
or operation of the Product in an unsuitable
environment or in a manner for which it is
not intended, including but not limited to
failures or defects caused by misuse, abuse,
accidents, physical damage, abnormal operation, improper handling or storage,
neglect, alterations, unauthorized installation, removal or repairs, failure to follow
instructions, problems caused by the carrier's network coverage, exposure to fire,
water or excessive moisture or dampness,
floods, or extreme changes in climate or
temperature, acts of God, riots, acts of terrorism, spills of food or liquids, viruses or
other software flaws introduced into the
Product or other acts which are not the fault
of Gigaset NAM and which the Product is
not specified to tolerate, including damage
caused by mishandling or blown fuses.
Products which have had warranty stickers,
electronic serial number and/or serial
number label removed, altered, rendered
illegible or fraudulently applied to other
equipment.
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
– Signal reception problems (unless caused by
defect in material or workmanship in the
Product).
– Products operated outside published maximum ratings.
– Performance of the Products when used in
combination with other products or equipment not manufactured, supplied or authorized by Gigaset NAM.
– Consumables (such as batteries and fuses).
– Payments for labor or service to representatives or service centers not authorized to
perform product maintenance by Gigaset
NAM.
– Loss of data.
– Testing and examination discloses that the
alleged defect or malfunction in the Product
does not exist.
This warranty does not cover customer education, instruction, installation or removal, set up
adjustments, problems related to service(s)
provided by a carrier or other service provider,
and/or signal reception problems. Gigaset NAM
shall not be responsible for software, firmware,
information, or memory data contained in,
stored on, or integrated with any Products
returned for repair, whether under warranty or
not. This warranty is valid only in the country in
which it is purchased (i.e., the United States of
America or Canada respectively, but not both).
USE WITH ACCESSORIES NOT SUPPLIED BY
GIGASET NAM OR NOT OTHERWISE
EXPRESSLY AUTHORIZED BY GIGASET NAM
MAY VOID WARRANTY.
4. WARRANTY CLAIM PROCEDURE
All warranty claims must be made by notifying
Gigaset NAM prior to the expiration of the warranty period. Gigaset NAM's obligation to provide warranty support shall not extend past the
end of the warranty period, except that any
product repaired or replaced during the warranty period shall continue to be warranted for
the balance of such warranty period or thirty
(30) days, whichever is greater.
Support service will be provided for you by
accessing the toll free customer service number:
1-866-247-8758
5. LIMITATION OF WARRANTY
Gigaset NAM makes no warranty or representation that the software in the Products will meet
your requirements or will work in combination
with any hardware or applications software
products provided by third parties, that the
operation of the software will be uninterrupted
or error free, or that all defects in the software
products will be corrected.
6. LIMITATION ON REMEDIES; NO
CONSEQUENTIAL OR OTHER
DAMAGES
Your exclusive remedy for any breach of this
limited warranty is as set forth above. Except
for any refund elected by Gigaset NAM, YOU
ARE NOT ENTITLED TO ANY DAMAGES,
INCLUDING BUT NOT LIMITED TO CONSEQUENTIAL DAMAGES, if the Product does not
meet the limited warranty , and, to the maximum extent allowed by applicable law, even if
any remedy fails of its essential purpose. The
terms below ("Exclusion of Incidental, Consequential and Certain Other Damages") are also
incorporated into this limited warranty . Some
states/jurisdictions/provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This limited
warranty gives you specific legal rights. You
may have others which vary from state/jurisdiction/province to state/jurisdiction/province.
7. DISCLAIMER OF WARRANTIES
GIGASET NAM AND ITS SUPPLIERS PROVIDE THE
PRODUCT AND SUPPORT SERVICES (IF ANY) AS
IS AND WITH ALL FAULTS. THE LIMITED WARRANTY IS IN LIEU OF ANY OTHER EXPRESS WARRANTIES (IF ANY) CREATED BY ANY DOCUMENTATION OR PACKAGING EXCEPT FOR THE LIMITED WARRANTY, AND TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW IS IN
LIEU OF ANY IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, OF
ACCURACY OR COMPLETENESS OR RESPONSES,
OF RESULTS, OF WORKMANLIKE EFFORT, OF
LACK OF VIRUSES AND OF LACK OF NEGLIGENCE, ALL WITH REGARD TO THE PRODUCT,
AND THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES. ALSO, THERE IS NO
WARRANTY OR CONDITION OF TITLE, QUIET
ENJOYMENT, QUIET POSSESSION, OR CORRESPONDENCE TO DESCRIPTION OR NONINFRINGEMENT WITH REGARD TO THE PRODUCT.
Some states/jurisdictions/provinces do not
allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
exclusions or limitations may not apply to you.
35
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Appendix
If an implied warranty or condition is created by
your state/province and federal or state/provincial law prohibits disclaimer of it, you also have
an implied warranty or condition, BUT ONLY AS
TO DEFECTS DISCOVERED DURING THE PERIOD
OF THIS LIMITED WARRANTY (ONE YEAR). AS
TO ANY DEFECTS DISCOVERED AFTER THE ONE
YEAR PERIOD, THERE IS NO WARRANTY OR CONDITION OF ANY KIND. This limited warranty
gives you specific legal rights, and you may also
have other rights which vary from state to
state/province to province. In no event shall
Gigaset NAM's liability exceed the cost of
repairing or replacing defective Products as
provided herein, and any such liabilities will terminate upon expiration of the warranty period.
Any supplements or updates to the Product or
the software in the Product, including without
limitation, any (if any) software fixes or
upgrades or bug fixes provided to you after the
expiration of the one year limited warranty
period are not covered by any warranty or condition, express, implied or statutory.
8. EXCLUSION OF INCIDENTAL,
CONSEQUENTIAL AND CERTAIN
OTHER DAMAGES
TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, IN NO EVENT SHALL GIGASET
NAM, SELLER OR THEIR SUPPLIERS BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER
(INCLUDING, BUT NOT LIMITED TO, DAMAGES
FOR LOSS OF PROFITS OR CONFIDENTIAL OR
OTHER INFORMATION, FOR BUSINESS INTERRUPTION, FOR PERSONAL INJURY, FOR LOSS OF
PRIVACY, FOR FAILURE TO MEET ANY DUTY
INCLUDING OF GOOD FAITH OR OF REASONABLE CARE, FOR NEGLIGENCE, AND FOR ANY
OTHER PECUNIARY OR OTHER LOSS WHATSOEVER) ARISING OUT OF OR IN ANY WAY
RELATED TO THE USE OF OR INABILITY TO USE
THE PRODUCT, THE PROVISION OF OR FAILURE
TO PROVIDE SUPPORT SERVICES, OR OTHERWISE UNDER OR IN CONNECTION WITH ANY
PROVISION OF THIS LIMITED WARRANTY, EVEN
IN THE EVENT OF THE FAULT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY, BREACH OF
CONTRACT OR BREACH OF WARRANTY OF
GIGASET NAM OR SELLER OR ANY SUPPLIER,
AND EVEN IF GIGASET NAM OR SELLER OR ANY
SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REPAIR OR REPLACEMENT, AS PROVIDED UNDER THE WARRANTY, IS
YOUR SOLE AND EXCLUSIVE REMEDY FOR
BREACH OF THE LIMITED WARRANTY.
36
9. LIMITATION OF LIABILITY AND
REMEDIES
NOTWITHSTANDING ANY DAMAGES THAT YOU
MIGHT INCUR FOR ANY REASON WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, ALL DAMAGES REFERENCED ABOVE AND ALL DIRECT OR
GENERAL DAMAGES), THE ENTIRE LIABILITY OF
GIGASET NAM, SELLER AND ANY OF THEIR SUPPLIERS UNDER ANY PROVISION OF THIS LIMITED
WARRANTY AND YOUR EXCLUSIVE REMEDY FOR
ALL OF THE FOREGOING (EXCEPT FOR ANY
REMEDY OF REPAIR OR REPLACEMENT ELECTED
BY GIGASET NAM OR SELLER OR SUPPLIER WITH
RESPECT TO ANY BREACH OF THE LIMITED WARRANTY) SHALL BE LIMITED TO THE GREATER OF
THE AMOUNT ACTUALLY PAID BY YOU FOR THE
PRODUCT OR FIVE DOLLARS ($5.00 USD/CAN).
THE FOREGOING LIMITATIONS, EXCLUSIONS
AND DISCLAIMERS SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
EVEN IF ANY REMEDY FAILS ITS ESSENTIAL PURPOSE.
10. GOVERNING LAW
If this Product was purchased in the United
States of America this limited warranty will be
governed by the laws of Texas, and exclude the
United Nations Convention on Contracts for the
International Sale of Goods. If this Product was
purchased in Canada this limited warranty will
be governed by the laws of the Province of
Ontario and the federal laws of Canada applicable therein, and exclude the United Nations
Convention on Contracts for the
International Sale of Goods.
If you want to learn more about Gigaset Service
or for Support on your Gigaset phone, visit our
web site at http://www.gigaset.com or please
call
1-866-247-8758.
Issued by
Gigaset Communications GmbH
Schlavenhorst 66, D-46395 Bocholt
Gigaset Communications GmbH is a licensee of
the Siemens trademark.
© Gigaset Communications GmbH 2009
All rights reserved.
Subject to availability. Rights of modifications
reserved.
Product attributes subject to change.
We reserve the right, to make changes without
notice in equipment design and/or components.
Part Number:
A31008-M1757-R401-1-5819
© Copyright 2009.
S18H / Canada EN / A31008-M1757-R401-1-5819 / appendix.fm / 22.6.09
Mounting the charging cradle to the wall
Mounting the charging cradle to the wall
1.02 in
approx.
0.25 in
37
S18H / Canada EN / A31008-M1757-R401-1-5819 / S18HSIX.fm / 22.6.09
Index
Index
A
Acknowledge tones . . . . . . . . . . . . . . 27
Activating
advisory tones . . . . . . . . . . . . . . . . 27
auto answer . . . . . . . . . . . . . . . . . . 25
handset . . . . . . . . . . . . . . . . . . . . . 14
keypad lock . . . . . . . . . . . . . . . . . . 14
room monitor . . . . . . . . . . . . . . . . 23
Adjusting
loud speaker volume . . . . . . . . . . . 26
Advisory tones . . . . . . . . . . . . . . . . . 27
Alarm clock . . . . . . . . . . . . . . . . . . . . 28
Alert tone . . . . . . . . . . . . . . . . . . . . . 27
Anniversary. . . . . . . . . . . . . . . . . . . . 18
storing in directory . . . . . . . . . . . . . 18
Answering machine list . . . . . . . . . . . 20
Answering machine, see
Network mailbox
Area codes . . . . . . . . . . . . . . . . . . . . 12
Auto answer . . . . . . . . . . . . . . . . 13, 25
B
Base station
changing . . . . . . . . . . . . . . . . . . . . 11
range . . . . . . . . . . . . . . . . . . . . . . . 7
Battery
charging . . . . . . . . . . . . . . . . . . . . 11
display . . . . . . . . . . . . . . . . . . . . . . 11
fitting . . . . . . . . . . . . . . . . . . . . . . . 8
icon . . . . . . . . . . . . . . . . . . . . . . . . 11
recommended batteries . . . . . . . . . 31
tone . . . . . . . . . . . . . . . . . . . . . . . 27
Best base station . . . . . . . . . . . . . . . . 11
Birthday, see Anniversary
C
Call
answering . . . . . . . . . . . . . . . . . . .
ending. . . . . . . . . . . . . . . . . . . . . .
external . . . . . . . . . . . . . . . . . . . . .
internal . . . . . . . . . . . . . . . . . . . . .
Call acceptance . . . . . . . . . . . . . . . . .
Call duration . . . . . . . . . . . . . . . . . . .
Call history . . . . . . . . . . . . . . . . . . . .
Calling
external . . . . . . . . . . . . . . . . . . . . .
Care of the telephone . . . . . . . . . . . .
38
13
13
13
14
25
13
19
13
30
Changing
destination number . . . . . . . . . . . . .24
display language . . . . . . . . . . . . . . .24
internal number of a handset . . . . . .27
name of handset . . . . . . . . . . . . . . .27
ringtone . . . . . . . . . . . . . . . . . . . . .26
Character set table, see
Special characters
Charge status display . . . . . . . . . . . . . 1
CID 2.5 services (network services) . . .16
Confirmation beep . . . . . . . . . . . . . . .27
Control key . . . . . . . . . . . . . . . . . .1, 14
Correcting incorrect input . . . . . . . . . .15
Customer Care . . . . . . . . . . . . . . . . . .34
D
Deactivating
advisory tones . . . . . . . . . . . . . . . .27
auto answer . . . . . . . . . . . . . . . . . .25
handset . . . . . . . . . . . . . . . . . . . . .14
keypad lock . . . . . . . . . . . . . . . . . . .14
room monitor . . . . . . . . . . . . . . . . .24
Delete key . . . . . . . . . . . . . . . . . . . . .15
Deleting
characters . . . . . . . . . . . . . . . . . . . .15
De-registering (handset) . . . . . . . . . . .11
Dialing
directory . . . . . . . . . . . . . . . . . . . . .17
with quick dial . . . . . . . . . . . . . . . .18
Dialing pause
entering . . . . . . . . . . . . . . . . . . . . . 1
Directory . . . . . . . . . . . . . . . . . . . . . .17
copying number from text . . . . . . . .18
managing entries . . . . . . . . . . . . . .17
opening . . . . . . . . . . . . . . . . . . . . .14
order of entries . . . . . . . . . . . . . . . .21
saving entry . . . . . . . . . . . . . . . . . .17
sending entry/list to handset . . . . . .18
storing anniversary . . . . . . . . . . . . .18
using to enter numbers . . . . . . . . . .18
Display
changing display language . . . . . . .24
contrast . . . . . . . . . . . . . . . . . . . . .24
in idle status . . . . . . . . . . . . . . . . . .15
keys . . . . . . . . . . . . . . . . . . . . . .1, 15
lighting . . . . . . . . . . . . . . . . . . . . . .25
memory . . . . . . . . . . . . . . . . . . . . .18
network mailbox message . . . . . . . .22
screen picture . . . . . . . . . . . . . . . . .25
setting . . . . . . . . . . . . . . . . . . . . . .24
S18H / Canada EN / A31008-M1757-R401-1-5819 / S18HSIX.fm / 22.6.09
Index
wrong language . . . . . . . . . . . . . . . 24
E
Earpiece mode . . . . . . . . . . . . . . . . . 13
Earpiece volume . . . . . . . . . . . . . . . . 26
End call key . . . . . . . . . . . . . . . . . . 1, 13
Ending, call . . . . . . . . . . . . . . . . . . . . 13
Ending, see Deactivate
Entry
selecting (menu) . . . . . . . . . . . . . . . 5
selecting from directory . . . . . . . . . 17
Error beep . . . . . . . . . . . . . . . . . . . . . 27
Example
menu input . . . . . . . . . . . . . . . . . . . 5
multiple line entry . . . . . . . . . . . . . . 6
F
Fast access
assigning key 1 . . . . . . . . . . . . . . . . 1
network mailbox . . . . . . . . . . . . . . 22
Flash key . . . . . . . . . . . . . . . . . . . . . . . 1
G
Group call . . . . . . . . . . . . . . . . . . . . . 14
H
Handset
activating/deactivating . . . . . . . . . . 14
advisory tones . . . . . . . . . . . . . . . . 27
changing internal number . . . . . . . 27
changing name . . . . . . . . . . . . . . . 27
changing number . . . . . . . . . . . . . 27
changing to best reception . . . . . . . 11
changing to different base
station . . . . . . . . . . . . . . . . . . 11
contact with liquid . . . . . . . . . . . . . 30
de-registering . . . . . . . . . . . . . . . . 11
display language . . . . . . . . . . . . . . 24
idle status . . . . . . . . . . . . . . . . 12, 15
lighting . . . . . . . . . . . . . . . . . . . . . 25
list . . . . . . . . . . . . . . . . . . . . . . . . . 14
loudspeaker volume . . . . . . . . . . . . 26
muting . . . . . . . . . . . . . . . . . . . . . 13
placing on hold . . . . . . . . . . . . . . . 13
reception strength . . . . . . . . . . . . . . 7
registering on another
base station. . . . . . . . . . . . . . . 11
restoring to factory settings . . . . . . 28
screen picture . . . . . . . . . . . . . . . . 25
setup . . . . . . . . . . . . . . . . . . . . . . . . 8
using room monitor . . . . . . . . . . . . 23
Handset charging times . . . . . . . . . . .31
Handset operating time . . . . . . . . . . .31
in room monitor mode . . . . . . . . . .23
Handset settings. . . . . . . . . . . . . . . . .24
Handsfree
key . . . . . . . . . . . . . . . . . . . . . . . . . 1
Handsfree talking . . . . . . . . . . . . . . . .13
Headset socket . . . . . . . . . . . . . . . . . .11
Hold . . . . . . . . . . . . . . . . . . . . . . . . .13
I
Icon
alarm clock . . . . . . . . . . . . . . . . . . .28
battery . . . . . . . . . . . . . . . . . . . . . .11
display . . . . . . . . . . . . . . . . . . . . . .15
keypad lock . . . . . . . . . . . . . . . . . . .14
ringtone . . . . . . . . . . . . . . . . . . . . .26
Idle status (display) . . . . . . . . . . . . . .12
Idle status, returning to . . . . . . . . . . .15
Incorrect input (correction) . . . . . . . . .15
Internal
making calls . . . . . . . . . . . . . . . . . .14
Internal call . . . . . . . . . . . . . . . . . . . .14
K
Key 1 (fast access) . . . . . . . . . . . . . . . 1
Keypad lock . . . . . . . . . . . . . . . . . . . .14
Keys
assigning directory entry . . . . . . . . .17
control key . . . . . . . . . . . . . . . . .1, 14
delete key . . . . . . . . . . . . . . . . . . . .15
display keys. . . . . . . . . . . . . . . . .1, 15
end call key . . . . . . . . . . . . . . . . .1, 13
fast access . . . . . . . . . . . . . . . . . . . 1
flash key . . . . . . . . . . . . . . . . . . . . . 1
handsfree key . . . . . . . . . . . . . . . . . 1
last number redial key . . . . . . . . . . .19
menu key . . . . . . . . . . . . . . . . . . . .15
message key . . . . . . . . . . . . . . . . . . 1
On/Off key . . . . . . . . . . . . . . . . . . . 1
pound key . . . . . . . . . . . . . . . . . .1, 14
quick dial . . . . . . . . . . . . . . . . .17, 18
star key . . . . . . . . . . . . . . . . . . . .1, 26
talk key . . . . . . . . . . . . . . . . . . . .1, 13
L
Language, display. . . . . . . . . . . . . . . .24
Last number redial . . . . . . . . . . . . . . .19
Lighting . . . . . . . . . . . . . . . . . . . . . . .25
Liquid . . . . . . . . . . . . . . . . . . . . . . . .30
39
S18H / Canada EN / A31008-M1757-R401-1-5819 / S18HSIX.fm / 22.6.09
Index
List
answering machine list. . . . . . . . . .
call history . . . . . . . . . . . . . . . . . . .
handsets . . . . . . . . . . . . . . . . . . . .
missed calls . . . . . . . . . . . . . . . . . .
Lock
activating/deactivating keypad
lock. . . . . . . . . . . . . . . . . . . . .
Loudspeaker volume . . . . . . . . . . . . .
20
19
14
20
Questions and answers . . . . . . . . . . . .30
Quick dial . . . . . . . . . . . . . . . . . . . . . .17
R
Making calls
answering a call . . . . . . . . . . . . . . . 13
external . . . . . . . . . . . . . . . . . . . . . 13
internal . . . . . . . . . . . . . . . . . . . . . 14
Manual last number redial . . . . . . . . . 19
Medical equipment . . . . . . . . . . . . . . . 3
Memory . . . . . . . . . . . . . . . . . . . . . . 18
Menu
end tone . . . . . . . . . . . . . . . . . . . . 27
key . . . . . . . . . . . . . . . . . . . . . . . . 15
menu guidance . . . . . . . . . . . . . . . 15
menu input . . . . . . . . . . . . . . . . . . . 5
opening . . . . . . . . . . . . . . . . . . 14, 15
overview . . . . . . . . . . . . . . . . . . . . 29
Message key
opening lists . . . . . . . . . . . . . . . . . 19
Messages
key . . . . . . . . . . . . . . . . . . . . . . . . . 1
Microphone . . . . . . . . . . . . . . . . . . . . 1
Missed call . . . . . . . . . . . . . . . . . . . . 20
Multiple line entry . . . . . . . . . . . . . . . . 6
Muting . . . . . . . . . . . . . . . . . . . . . . . 13
N
27
22
16
18
23
18
18
17
O
On/Off key . . . . . . . . . . . . . . . . . . . . . 1
Order of entries in directory . . . . . . . . 21
40
Package contents . . . . . . . . . . . . . . . . 7
Placing the handset on hold . . . . . . . .13
Pound key . . . . . . . . . . . . . . . . . . .1, 14
Power supply unit . . . . . . . . . . . . . . . . 3
Q
14
26
M
Name
of a handset. . . . . . . . . . . . . . . . . .
Network mailbox . . . . . . . . . . . . . . . .
Network services (CID 2.5 services) . .
Number
adding to directory . . . . . . . . . . . . .
as destination for room monitor . . .
copying from directory . . . . . . . . . .
entry using directory . . . . . . . . . . .
saving in directory . . . . . . . . . . . . .
P
Range . . . . . . . . . . . . . . . . . . . . . . . . 7
Reception strength . . . . . . . . . . . . . . . 7
Redial
key . . . . . . . . . . . . . . . . . . . . . . . . .19
Reminder call . . . . . . . . . . . . . . . . . . .19
Ringtone
changing . . . . . . . . . . . . . . . . . . . .26
setting . . . . . . . . . . . . . . . . . . . . . .26
setting melody . . . . . . . . . . . . . . . .26
setting volume . . . . . . . . . . . . . . . .26
Room monitor . . . . . . . . . . . . . . . . . .23
S
Safety precautions . . . . . . . . . . . . . . . 3
Screen picture . . . . . . . . . . . . . . . . . .25
Searching in directory . . . . . . . . . . . . .17
Sending
directory entry to handset . . . . . . . .18
Sensitivity (room monitor) . . . . . . . . .23
Setting
date . . . . . . . . . . . . . . . . . . . . . . . .12
lighting . . . . . . . . . . . . . . . . . . . . . .25
screen picture . . . . . . . . . . . . . . . . .25
time . . . . . . . . . . . . . . . . . . . . . . . .12
Setting melody . . . . . . . . . . . . . . . . . .26
Setup
handset . . . . . . . . . . . . . . . . . . . . . 8
Shortcut. . . . . . . . . . . . . . . . . . . . . . .29
Sleep mode . . . . . . . . . . . . . . . . . . . .28
Sound, see Ringtone
Special characters . . . . . . . . . . . . . . . .21
Specifications . . . . . . . . . . . . . . . . . . .31
Star key . . . . . . . . . . . . . . . . . . . . .1, 26
T
Talk key . . . . . . . . . . . . . . . . . . . . .1, 13
Troubleshooting . . . . . . . . . . . . . . . . .30
S18H / Canada EN / A31008-M1757-R401-1-5819 / S18HSIX.fm / 22.6.09
Index
V
Viewing network mailbox message . .
VIP (directory entry) . . . . . . . . . . . . .
Volume
earpiece . . . . . . . . . . . . . . . . . . . .
handset loudspeaker . . . . . . . . . . .
loudspeaker . . . . . . . . . . . . . . . . . .
ringtone . . . . . . . . . . . . . . . . . . . .
setting . . . . . . . . . . . . . . . . . . . . . .
22
18
26
26
26
26
26
W
Warning beep, see Advisory tones
Writing, editing names . . . . . . . . . . . 20
41