Chicago Pneumatic SD25 Specifications

Add to my manuals
69 Pages

advertisement

Chicago Pneumatic SD25 Specifications | Manualzz
Valve terminals MPA-L
Valve terminals MPA-L
Key features
Innovative
Compact, high-performance valves
in a sturdy metal housing
Flow rates up to 870 l/min
Wide range of electrical connection
options for multi-pin plug: Sub-D,
flat cable or terminal strip
Connection to the electrical
peripherals CPX with a wide range
of communication options
I-Port/IO-Link interface
Freely configurable push-in
connectors
2
Versatile
Modular system offering a range of
configuration options
Freely extendable system with
individual sub-bases and modular
tie rods
Up to 32 solenoid coils
Conversions and extensions
possible at a later date
Air supply can be extended by
additional pressure zones via
supply modules
Wide range of pressures
–0.9 … 10 bar
Wide range of valve functions
è Internet: www.festo.com/catalog/...
Reliable
High output reserves thanks to
large pneumatic cross sections and
venting with high flow rates
Resilient thanks to high mechanical
rigidity
Lightweight and low-cost polymer
components
Fast troubleshooting thanks to LEDs
on the valves
Easy to service thanks to
replaceable valves and electronic
modules
Manual override either
non-detenting, detenting or secured
against unauthorised activation
(covered)
Durable thanks to tried-and-tested
piston spool valves
Easy to assemble
Fast and reliable in-house
assembly using individual
components or delivered as a
ready-to-install and tested unit
Lower selection, ordering,
installation and commissioning
costs
Secure mounting on wall or H-rail
Subject to change – 2015/03
Valve terminals MPA-L
Key features
Reliable operation:
Non-detenting/detenting or covered manual override
Width 10 mm, 14 mm and 20 mm
Reduced downtimes:
LED switching status display
Adaptable:
Selector in the end plate for defining
the pilot air supply (internal or external)
Pneumatic interface to CPX
CPX diagnostic interface for
handheld devices
Space-saving:
Slim valves and flat plate silencers
Simple electrical connections
– Multi-pin plug, fieldbus connections
– Control block, CPX
– I-Port interface/IO-Link
Practical:
Pre-assembled QS cartridge fittings
Quick mounting:
Directly using screws or on an H-rail
Flexible:
32 valve positions/32 solenoid coils
Modular:
Pressure zone creation, additional
exhaust and supply ports possible using
supply module
Safe:
Operating voltage connection,
outputs and valves can each be
switched off separately
Equipment options
Valve functions
5/2-way valve, single solenoid
5/2-way valve, double solenoid
2x 3/2-way valve,
normally open
2x 3/2-way valve,
normally closed
2x 3/2-way valve,
1x normally open,
1x normally closed
5/3-way valve,
mid-position pressurised
5/3-way valve,
mid-position closed
5/3-way valve,
mid-position exhausted
2x 2/2-way valve,
1x normally closed,
1x normally closed, reversible
2x 2/2-way valve,
normally closed
1x 3/2-way valve,
normally closed,
external compressed air supply
1x 3/2-way valve,
normally open,
external compressed air supply
Manual pressure regulators
All valves have the same compact
dimensions with an overall length of
107 mm and a height of 55 mm.
integrated holding current
reduction
Any compressed air supply
(max. 8 supply modules)
Creation of pressure zones
Modular, individually extendable
tie rods
Single valves or combinations of
four valves
Tubing size at each connection
freely selectable
Special features
Max. 32 valve positions/max.
32 solenoid coils
Parallel, modular valve linking
Electrical interlinking with
Online via: è www.festo.com
2D/3D CAD data
Valve terminal selection
Valve terminal configurator
The appropriate MPA-L valve terminal
can be chosen quickly and easily
using the online catalogue. This
includes a convenient valve terminal
configurator, which makes it much
simpler to order the right product.
2015/03 – Subject to change
The valve terminals are fully
assembled according to your order
specification and are individually
tested. This reduces assembly and
installation time to a minimum.
You order a valve terminal MPA-L
using the order code.
Ordering system for MPA-L
è Internet: mpal
Ordering system for CPX
è Internet: cpx
Ordering system for CTEU
è Internet: cteu
è Internet: www.festo.com/catalog/...
You can request the CAD data for a
valve terminal you have configured. To
do so, start the product search as
described above. Go to the shopping
basket and click on the CAD icon
(compass). On the next page you can
generate a 3D preview or request
another data format of your choice by
e-mail.
3
Valve terminals MPA-L
Key features
Individual connection
Valves on individual sub-bases can
also be used for actuators further
away from the valve terminal. The
valves are screwed to an individual
sub-base made from die-cast alu­
minium.
The electrical connection is estab­
lished using a standard 4-pin M8
plug (EN 60947-5-2).
Further information
è Internet: vmpa1
Individual sub-base assembly
1 Mounting holes
horizontal
2 Mounting holes
vertical
2
The individual sub-base for wall
mounting is designed for integration
into a system or machine. It can be
mounted horizontally or vertically.
1
Multi-pin plug connection
The signal flow from the controller to
the valve terminal takes place via a
pre-assembled or self-assembled
multi-wire cable to the multi-pin plug
connection, which substantially
reduces installation time.
4
è Internet: www.festo.com/catalog/...
The valve terminal can be equipped
with max. 32 solenoid coils. This
corresponds to 2 to 32 valves.
Versions
Sub-D connection
– Pre-assembled multi-pin cable
– Multi-pin cable for self-assembly
Flat cable connection
Terminal strip connection
Subject to change – 2015/03
Valve terminals MPA-L
Key features
Fieldbus connection via the CPX system
An integrated fieldbus node manages
communication with a higher-order
PLC. This enables a space-saving
pneumatic and electronic solution.
Valve terminals with fieldbus
interfaces can be configured with up
to 32 sub-bases.
The CPX terminal also enables the
integration of digital and analogue
electrical inputs and outputs,
pressure sensors and controllers for
pneumatic or electric positioning
axes.
A detailed description of the extensive
functionality can be found in the
documentation for the CPX terminal
è Internet: cpx
Fieldbus protocols/CPX variants:
PROFIBUS DP
PROFINET
INTERBUS
DeviceNet
CANopen
CC-Link
EtherNet/IP
Front End Controller
Remote I/O
Modbus/TCP
EtherCAT
In the slave operating mode, these
valve terminals can be used for
intelligent preprocessing and are
therefore ideal modules for designing
decentralised intelligence.
In the master operating mode,
terminal groups can be designed with
many options and functions that can
autonomously control a medium-sized
machine/system.
Communication with a higher-level
PLC is managed by a fieldbus node
mounted directly on the I-Port
interface.
Valve terminals with an I-Port
interface can be configured with up to
32 sub-bases.
A detailed description of the extensive
functionality can be found in the
documentation for the fieldbus
modules CTEU/installation
system CTEL
è Internet: cteu
Fieldbus protocols:
PROFIBUS DP
DeviceNet
CANopen
CC-Link
EtherCAT
I-Port/IO-Link consists of a central
master and the devices with I-Port
interface/IO-Link connected via
special connecting cables. This
permits a decentralised layout of the
devices.
The connection type corresponds to a
star topology.
In other words, only one module or
valve terminal can be connected to
each I-Port.
The I-Port interface from Festo is
based on IO-Link and is compatible
with IO-Link in certain areas.
As well as communication, the I-Port
interfaces also handle the power
supply for the connected devices.
The maximum length of a string is
20 m.
Control block connection via the CPX system
Controllers integrated in the Festo
valve terminals enable the
construction of stand-alone control
units to IP65, without control
cabinets.
Fieldbus connection via the CTEU system
I-Port interface/IO-Link
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
5
Valve terminals MPA-L
Peripherals overview
Modular pneumatic components
The modular design of the MPA-L
facilitates maximum flexibility right
from the planning stage and offers
maximum ease of servicing during
operation.
The system consists of sub-bases and
valves.
The sub-bases form the support
system for the valves.
They contain the connection ducts for
supplying compressed air to and
venting from the valve terminal as
well as the working lines for the
pneumatic drives for each valve.
The sub-bases are joined together via
a tie rod system. This consists of a
threaded rod, threaded sleeve and
screw. The threaded rod/sleeve
combination is selected as
appropriate to the chosen number of
individual sub-bases.
A valve terminal can be easily
extended by adding individual
sub-bases or supply modules. This is
done by inserting suitable tie rod
extenders between the threaded rod
and sleeve.
This ensures that the valve terminal
can be rapidly and reliably extended.
-H-
Note
The tie rod system for the valve
terminal MPA-L consists of at least
four sub-bases or two sub-bases
and one supply module.
Shorter valve terminals with two or
more valve positions can be
constructed without a sleeve.
Modular electrical peripherals
The mechanical connection between
the CPX modules is established using
tie rods. Two screws in the end plates
are all that are needed to assemble
the entire unit.
The tie rod ensures that the unit
resists high mechanical loads and is
therefore the "mechanical backbone"
of the CPX terminal.
The tie rod extension kit allows an
extra module to be added to the CPX
terminal.
The input/output modules,
connection blocks, fieldbus nodes or
control block of the CPX system are
mounted on the interlinking blocks
using four screws and can be almost
infinitely replaced or modified.
The open design allows interlinking
blocks to be replaced in assembled
state.
6
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Peripherals overview
Individual sub-base
Ordering:
Using individual part numbers
Individual sub-bases can be equipped
with any valve (VMPA… of the
corresponding width).
The electrical connection is estab­
lished using a standard 4-pin M8
plug (EN 60947-5-2).
5
4
3
2
1
9
6
8
7
Designation
Brief description
è Page/Internet
1
2
3
4
5
6
7
8
9
Width 10 mm, 14 mm, 20 mm
Non-detenting/turning with detent, per solenoid coil
MO non-detenting only once cover cap fitted
MO blocked once cover cap fitted
MO detenting and can be operated without accessories once cover cap fitted
For individual valve VMPA…
For working ports (2, 4) and air/exhaust ports (1, 3, 5)
For pilot air supply/pilot exhaust air (12/14, 82/84) and pressure compensation
4-pin
VMPA1
VMPA1
VMPA1
VMPA1
VMPA1
VMPA1
VMPA1
VMPA1
VMPA1
Solenoid valve
Manual override (MO)
Cover cap
Cover cap
Cover cap
Sub-base
Fittings and/or silencers
Fittings, silencers or blanking plugs
Electrical connection M8
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
7
Valve terminals MPA-L
Peripherals overview
Valve terminal – pneumatic components
The sub-bases are available
individually with one valve position or
with four valve positions.
Double solenoid valve positions
can be fitted with any valve or a
blanking plate.
The electrical interlinking modules
are available for:
1 or 4 single solenoid valves
1 or 4 double solenoid valves
8
6
7
Single solenoid valve positions can
only be fitted with single solenoid
valves or a blanking plate.
9
4
5
aJ
5
aA
4
3
aB
2
1
bF
bE
aC
aD
aE
aF
bB
bD
8
bC
bA
bJ
aI
aH
aG
3
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Peripherals overview
Valve terminal – pneumatic components
Designation
1
2
3
4
5
6
Plate
Plate
Cartridge fitting
Cover cap for manual override
Solenoid valve
Electrical interlinking module, 4-way
7
8
9
aJ
aA
aB
aC
aD
aE
aF
aG
aH
aI
bJ
bA
bB
bC
bD
bE
bF
Mounting bracket
Regulator plate
Pressure gauge
Right-hand end plate, low
Screw
Right-hand end plate, high
Inscription label
Holder for inscription label
Sub-base
Sleeve
Tie rod extender
Tie rod
Cartridge fitting
Sub-base, individual
Electrical interlinking module
Clamp strap for cartridge fitting
Supply module
Electrical interlinking module
Restrictor
Retainer for restrictor
2015/03 – Subject to change
Brief description
è Page/Internet
Exhaust plate as flat plate silencer
Exhaust plate for ducted exhaust air
For supply and exhaust ports
Conversion from detenting/non-detenting to non-detenting or detenting or covered
Single solenoid
Electrical interlinking module for combination of four sub-bases, single solenoid/double
solenoid
Mounting bracket for wall mounting
Vertical stacking (pressure regulator, vertical pressure shut-off plate, vertical supply plate)
Can be optionally mounted on a pressure regulator plate
End plate with pilot air selector, with ports 12/14, 82/84
Tie rod system, connects the sub-bases
End plate with pilot air selector, with ports 1, 3, 5, 12/14, 82/84
6 x 10 mm
–
Four individual sub-bases screwed together to form one unit
Tie rod system, connects the sub-bases
For subsequent modular extension of the valve terminal
Threaded rod, clamps the sub-bases between the end plates
For working lines
Sub-base with one valve position
Electrical interlinking module for single sub-base, single solenoid/double solenoid
–
For compressed air supply/exhaust air
Electrical interlinking module for supply module, signals are passed through
Fixed restrictor for installation in duct 3 or 5 of the sub-base
Required to install the fixed restrictor
61
61
64
60
50
53
è Internet: www.festo.com/catalog/...
60
51
51
62
59
62
60
60
53
59
59
59
64
53
53
–
61
53
52
52
9
Valve terminals MPA-L
Peripherals overview
Valve terminal with multi-pin plug connection
Order code:
34P-…
MPA-L valve terminals with multi-pin
plug connection can be expanded by
up to 32 solenoid coils/valve
positions.
The multi-pin plug connection is
removable and designed as a 9, 25 or
44-pin Sub-D connection. The
multi-pin plug connection can
alternatively be ordered as a terminal
strip (33-pin) or flat cable connection
(40-pin).
5
4
3
6
The Sub-D multi-pin plug connection,
25 and 44-pin, is available in IP40
and IP67 or with multi-pin plug cover,
without connecting cable, with a
choice of cable outlet to the side or
front.
8
7
2
Sub-D multi-pin plug connection,
25 and 44-pin, with multi-pin plug
cover with pre-assembled cable:
2.5 m
5m
10 m
Variable, up to 30 m
1
Designation
Brief description
è Page/Internet
1
2
3
4
5
6
7
8
Terminal strip, 33-pin, IP40
For flat cable, 40-pin, IP40
Sub-D, 25-pin
Sub-D, 9-pin, IP40
With cover, pre-assembled, connection on side, IP67
For self-assembly, connection on side, IP67
For self-assembly, connection on front, IP67
With cover, pre-assembled, connection on front, IP67
62
62
62
62
63
63
63
63
10
Multi-pin plug connection
Multi-pin plug connection
Multi-pin plug connection
Multi-pin plug connection
Connecting cable
Cover
Cover
Connecting cable
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Peripherals overview
Valve terminal with fieldbus connection, control block (electrical peripherals CPX)
Order code:
34P-… for the pneumatic
components
50E-… for the electrical
peripherals
Valve terminals with CPX interface can
be expanded by up to 32 solenoid
coils/valve positions.
Up to 32 valve positions can be
equipped in combination with single
solenoid valves; the maximum
number of valve positions is reduced
to 16 if only double solenoid valves
are used.
The maximum number of addresses is
set in the range 4 … 32 solenoid coils
via a selector switch.
This enables extensions to be
pre-assigned in a control program and
called up by means of manual
settings.
Each valve position can be equipped
with any valve or a blanking plate. The
rules for CPX apply to the equipment
that can be used in combination with
the electrical peripherals CPX.
In general:
Digital inputs/outputs
Analogue inputs/outputs
Parameterisation of inputs and
outputs
Integrated multi-featured
diagnostic system
Preventive maintenance concepts
3
2
1
4
4
4
Designation
Brief description
è Page/Internet
1
2
3
4
Fieldbus node, control block, input and output modules
Pneumatic interface for CPX terminal
Large, for left-hand end plate/pneumatic interface for CPX terminal
–
cpx
62
–
60
CPX modules
Left-hand end plate
Inscription label
H-rail mounting
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
11
Valve terminals MPA-L
Peripherals overview
Valve terminal with I-Port interface/IO-Link (and fieldbus node)
Order code:
34P-… for the pneumatic
components
CTEU-… for the fieldbus node
1
2
Valve terminals with I-Port
interface/IO-Link can be expanded by
up to 32 solenoid coils/valve
positions.
Up to 32 valve positions can be
equipped in combination with single
solenoid valves.
3
The maximum number of valve
positions is reduced to 16 if only
double solenoid valves are used.
Each valve position can be equipped
with any valve or a blanking plate.
4
5
6
7
8
Designation
Brief description
è Page/Internet
1
2
3
5
6
7
8
Fieldbus node
For I-Port interface/IO-Link
For I-Port interface/IO-Link
Between two I-Port interfaces
With bus node for connecting two devices with I-Port interfaces
For electrical sub-base
End plate with I-Port interface/IO-Link
cteu
sea
fb-ta
nebv
cteu
cteu
62
12
Fieldbus node CTEU
Plug
T-adapter
Connecting cable
Electrical sub-base
H-rail mounting
Left-hand end plate
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
Sub-base valve
MPA-L offers a comprehensive range
of valve functions. All valves are
equipped with piston spool and
patented sealing system that
facilitates efficient sealing, a broad
pressure range and long service life.
They have a pneumatic pilot control
for optimising performance.
Air is supplied by means of pilot air
supply.
Sub-base valves can be quickly
replaced since the tubing connectors
remain on the sub-base.
This design is also particularly slim.
replaced. The mechanical sturdiness
of the sub-base guarantees good
long-term sealing.
Blanking plates can be replaced by
valves at a later date. The dimensions,
mounting points and existing
pneumatic installations remain
Design
Valve replacement
The valves are attached to the
sub-base using two screws,
which means that they can be easily
Extension
-H-
2015/03 – Subject to change
unchanged during this process.
The valve code (e.g. M, J, N, NS, NU,
etc.) is located on the front of the
valve beneath the manual override.
Note
A filter must be installed upstream of
valves operated in vacuum mode.
This prevents any foreign matter in
5/2-way valve
Circuit symbol
Irrespective of the valve function there
are sub-base valves with one solenoid
coil (single solenoid) or with two
solenoid coils (double solenoid or two
single solenoid valves in one
housing).
the intake air getting into the valve
(e.g. when operating a suction cup).
Code
Description
Position function 1-32: M
Single solenoid
Pneumatic spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: MS
Single solenoid
Mechanical spring return
Reversible
Operating pressure –0.9 … +8 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: MU
Single solenoid
Polymer poppet valve
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm
Position function 1-32: J
Double solenoid
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm, 14 mm
and 20 mm
è Internet: www.festo.com/catalog/...
13
Valve terminals MPA-L
Key features – Pneumatic components
2x 3/2-way valve
Circuit symbol
14
Code
Description
Position function 1-32: N
Single solenoid
Normally open
Pneumatic spring return
Operating pressure 3 … 10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: NS
Single solenoid
Normally open
Mechanical spring return
Reversible
Operating pressure –0.9 … +8 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: NU
Single solenoid
Polymer poppet valve
Normally open
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm
Position function 1-32: K
Single solenoid
Normally closed
Pneumatic spring return
Operating pressure 3 … 10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: KS
Single solenoid
Normally closed
Mechanical spring return
Reversible
Operating pressure –0.9 … +8 bar
Available in width 110 mm,
14 mm and 20 mm
Position function 1-32: KU
Single solenoid
Polymer poppet valve
Normally closed
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm
Position function 1-32: H
Single solenoid
Normal position
– 1x closed
– 1x open
Pneumatic spring return
Operating pressure 3 … 10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: HS
Single solenoid
Normal position
– 1x closed
– 1x open
Mechanical spring return
Reversible
Operating pressure –0.9 … +8 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: HU
Single solenoid
Polymer poppet valve
Normal position
– 1x closed
– 1x open
è Internet: www.festo.com/catalog/...
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
5/3-way valve
Circuit symbol
1)
Code
Description
Position function 1-32: B
Mid-position pressurised1)
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: G
Mid-position closed1)
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: E
Mid-position exhausted1)
Mechanical spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm, 14 mm
and 20 mm
If neither solenoid coil is energised, the valve moves to its mid-position by means of spring force.
If both coils are energised at the same time, the valve remains in the previously assumed switching position.
3/2-way valve
Circuit symbol
Code
Description
Position function 1-32: W
Position function 1-32: X
2x 2/2-way valve
Circuit symbol
2015/03 – Subject to change
Single solenoid
Normally open
External compressed air supply
Pneumatic spring return
Reversible
Operating pressure –0.9 … +10 bar
Single solenoid
Normally closed
External compressed air supply
Pneumatic spring return
Reversible
Operating pressure –0.9 … +10 bar
Available in width 10 mm, 14 mm
and 20 mm
Compressed air (–0.9 … +10 bar)
supplied at working line 2 can be
switched with both internal and
external pilot air supply.
Available in width 10 mm, 14 mm
and 20 mm
Compressed air (–0.9 … +10 bar)
supplied at working line 4 can be
switched with both internal and
external pilot air supply.
Code
Description
Position function 1-32: D
Single solenoid
Normally closed
Pneumatic spring return
Operating pressure 3 … 10 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: DS
Single solenoid
Normally closed
Mechanical spring return
Reversible
Operating pressure –0.9 … +8 bar
Available in width 10 mm, 14 mm
and 20 mm
Position function 1-32: I
Single solenoid
1x normally closed
1x normally closed, reversible
Pneumatic spring return
Operating pressure 3 … 10 bar
Vacuum at port 3/5 only
Available in width 10 mm, 14 mm
and 20 mm
è Internet: www.festo.com/catalog/...
15
Valve terminals MPA-L
Key features – Pneumatic components
Blanking plate
Blanking plate (code L) without valve
function, for reserving valve positions
on a valve terminal.
Valves and blanking plates are
attached to the sub-base using two
screws.
The fixed restrictor can be used to
permanently set the flow rate when
venting in ducts 3 and 5.
The restrictor cuts a thread into the
retainer as it is screwed in. For that
reason, the retainer should also be
changed when a restrictor is
repeatedly replaced.
Fixed restrictor
Mounting:
Press the retainer as far as it will go
into the exhaust openings on the
sub-base
Screw the fixed restrictor into the
retainer
Mount the valve on the sub-base
-H-
The restrictor is available in
seven different nominal sizes
(0.3 …. 1.7 mm). The individual sizes
are colour-coded to make them easy
to distinguish.
Fixed restrictors enable, for example,
the cylinder speed to be set to a
predefined limit in response to known
flow rate conditions.
They cannot be accessed during
operation and are therefore protected
against manipulation.
This is beneficial in the production of
standard machines since the required
speed can be determined once and
the installation simply duplicated for
further machines, saving time and
costs for repeated commissioning.
Note
The fixed restrictors are only
available for valves and manifold
sub-bases with a width of 10 mm.
16
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
Vertical stacking
Additional functions can be added to
each valve position between the
sub-base and the valve.
These functions are known as vertical
stacking modules and enable special
functioning or control of an individual
valve position.
An adjustable pressure regulator can
be installed between the sub-base
and the valve in order to control the
force of the triggered actuator.
This pressure regulator maintains an
essentially constant output pressure
(secondary side) independent of
pressure fluctuations (primary side)
and air consumption.
Standard version:
For supply pressure up to 6 bar or
up to 10 bar
Without pressure gauge (optional,
rotatable)
Adjusted using a screwdriver or
regulator knob
Pressure regulator plate
Vertical pressure shut-off plate for width 10 mm
The vertical pressure shut-off plate
can be used to hot swap individual
valves without switching off the
overall air supply.
The working pressure for the
individual valve can be switched off
manually via the vertical pressure
shut-off plate using the actuating
element.
Vertical pressure supply plate for width of 20 mm
This vertical pressure supply plate
enables an individual valve to be
supplied with individual operating
pressure independently of the operat­
ing pressure of the valve terminal.
2015/03 – Subject to change
The exhaust and pilot air supply of the
valve are still provided via the central
connections of the valve terminal.
è Internet: www.festo.com/catalog/...
17
Valve terminals MPA-L
Key features – Pneumatic components
Pressure regulator
Circuit symbol
Vertical pressure shut-off plate
Circuit symbol
18
Code
Description
Pressure regulator 1-32: PA
Pressure regulator 1-32: PF
Regulates the pressure upstream
of the valve in duct 1
Same regulated pressure at duct 2
and duct 4
Venting in the valve from duct 2 to
duct 3 and from duct 4 to duct 5
Regulator not affected by venting
Regulator can always be adjusted
Available in width 10 mm and
20 mm
Pressure regulator 1-32: PC
Pressure regulator 1-32: PH
Regulates the pressure for duct 2
downstream of the valve
Venting via the regulator from
duct 2 to duct 3
Exhaust flow rate is restricted by
the regulator
Regulator can only be adjusted in
switched state
Available in width 10 mm and
20 mm
Pressure regulator 1-32: PB
Pressure regulator 1-32: PG
Regulates the pressure for duct 4
downstream of the valve
Venting via the regulator from
duct 4 to duct 5
Exhaust flow rate is restricted by
the regulator
Regulator can only be adjusted in
switched state
Available in width 10 mm and
20 mm
Pressure regulator 1-32: PN
Pressure regulator 1-32: PL
Splits the supply air in duct 1 and
regulates the pressure upstream of
the valve in duct 3
Valve is operated in reverse mode
Venting in the valve from duct 2 to
duct 1
Regulator not affected by venting
Regulator can always be adjusted
Available in width 20 mm
Pressure regulator 1-32: PK
Pressure regulator 1-32: PM
Splits the supply air in duct 1 and
regulates the pressure upstream of
the valve in duct 5
Valve is operated in reverse mode
Venting in the valve from duct 4 to
duct 1
Regulator not affected by venting
Regulator can always be adjusted
Available in width 20 mm
Code
Description
Pressure regulator 1-32: PS
Allows the pressure in duct 1 and
duct 12/14 to be switched off
upstream of the valve
Venting in the valve from duct 2 to
duct 3 and from duct 4 to duct 5
è Internet: www.festo.com/catalog/...
Vertical pressure shut-off plate not
affected by venting
Operating pressure 3 … 8 bar
Available in width 10 mm
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
Vertical pressure supply plate
Circuit symbol
Code
Description
Pressure regulator 1-32: PV
Enables separate supply of the
pressure in duct 1 and upstream
of the valve
Operating pressure –0.9 … +10 bar
Available in width of 20 mm
The valve terminal MPA-L can be
supplied with compressed air at one
or more points via supply modules
and/or the right-hand end plate. The
generously sized pneumatic system
enables good performance from all
functional components, even with
large-scale expansions.
Venting (ducts 3 and 5) either takes
place via silencers or ports for ducted
exhaust air via the supply modules or
the right-hand end plate.
There are two types of supply module
with venting:
Exhaust air 3/5 via flat plate
silencer
Exhaust air 3/5 ducted
Venting (ducts 3 and 5) can
alternatively or additionally take
place via the right-hand end plate.
Ducts 3 and 5 are separate in the
terminal and are only joined together
in the supply module. The exhaust air
from the pilot air (duct 82/84) is
entirely separate from ducts 3 and 5.
supply can be selected at the pilot air
selector on the end plate:
Internal (from duct 1) or
External (from duct 12/14)
Internal pilot air supply can be
selected if the supply pressure for the
terminal is between 3 and 8 bar.
In this case, the pilot air supply is
branched by means of an internal
connection from duct 1 in the
right-hand end plate.
Port 12/14 on the right-hand end
plate can be sealed using a blanking
plug.
If the supply pressure (at the
right-hand end plate) is less than
3 bar or greater than 8 bar, then the
valve terminal MPA-L must be
operated with an external pilot air
supply. The pilot air supply is then fed
via port 12/14 on the right-hand end
plate. When using several pressure
zones, the supply pressure in the
pressure zone with the right-hand end
plate is decisive.
Compressed air supply and venting
Supply module
Right-hand end plate
Pilot air supply
The valve terminal MPA-L is supplied
with pilot air exclusively via the
right-hand end plate. The pilot air
Switching position for internal, marked "Int"
Switching position for external, marked "Ext"
-H-
Note
If a gradual pressure build-up in the
system using a soft-start valve is
chosen, an external pilot air supply
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
should be connected so that the
control pressure applied during
switch-on is already very high.
19
Valve terminals MPA-L
Key features – Pneumatic components
Compressed air supply and pilot air supply
Graphical illustration
Code
Right-hand end plate, with supply ports
Right-hand end plate: D
Pilot air: –
Right-hand end plate: D
Pilot air: E
Right-hand end plate, without supply ports
Right-hand end plate: –
Pilot air: –
Notes
Internal pilot air supply
Pilot air is branched internally from port 1 in the right-hand end plate
Exhaust air 3/5 via right-hand end plate or supply module
Pilot exhaust air 82/84 via right-hand end plate
For operating pressure in the range 3 … 8 bar
External pilot air supply
Pilot air supply (3 … 8 bar) is connected at the right-hand end plate at port 12/14
Exhaust air 3/5 via right-hand end plate or supply module
Pilot exhaust air 82/84 via right-hand end plate
For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Internal pilot air supply
Pilot air is branched internally from port 1 in the right-hand end plate
Exhaust air 3/5 via supply module
Pilot exhaust air 82/84 via right-hand end plate
For operating pressure in the range 3 … 8 bar
Right-hand end plate: –
Pilot air: E
External pilot air supply
Pilot air supply (3 … 8 bar) is connected at the right-hand end plate at port 12/14
Exhaust air 3/5 via supply module
Pilot exhaust air 82/84 via right-hand end plate
For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Type of module block 1-40: U
Exhaust port: –
Exhaust air 3/5 via flat plate silencer
Pilot exhaust air 82/84 via right-hand end plate
For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Type of module block 1-40: U
Exhaust port:
UD, UE, UF, UM, UN, UP or UG
Exhaust air 3/5 via supply module
Pilot exhaust air 82/84 via right-hand end plate
For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Supply module, flat plate silencer
Supply module, ducted exhaust air
20
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
Supply module
Illustration
Code
Type
Designation
Notes
Exhaust port:
UD, UE, UF, UM, UN, UP or UG
VMPAL-EG
Exhaust plate for ducted
exhaust air
Exhaust port: –
VMPAL-EU
Flat plate silencer
Type of module block 1-40: U
VMPAL-SP-0
Supply module with elec­
trical interlinking module
Additional supply modules can be used
for larger terminals or to create
additional pressure zones.
Supply modules can be configured at
any point upstream or downstream of
the sub-bases.
Supply modules contain the following
ports:
Compressed air supply (duct 1)
Exhaust air (duct 3/5)
Depending on your order, the exhaust
ducts are either ducted or vented via
the flat plate silencer.
Ports for supply and venting
Code
Right-hand end plate with supply ports 1, 3, 5
Right-hand end
plate: D
Port
QS push-in fitting/cartridge fitting
1
Air/vacuum supply
Thread G¼
QS-G¼, straight,
for tubing O.D.  8 mm, 10 mm, 12 mm, Ć, y†,
½†
3
Exhaust air
Thread G¼
5
Exhaust air
Thread G¼
12/14
Pilot air supply
Thread M7
82/84
Pilot exhaust air
Thread M7
1
Air/vacuum supply
Cartridge fitting
3/5
Exhaust air
Flat plate silencer –
QSM-M7, straight or angled,
for tubing O.D.  4 mm, 6 mm, ¼†
Supply module
Type of module
block 1-40: U
Right-hand end plate without supply ports
Right-hand end
plate: –
2015/03 – Subject to change
QSPKG20, straight,
for tubing O.D.  8 mm, 10 mm, 12 mm, Ć, y†,
½†, adapter for thread G¼
Cartridge fitting
QSPKG20, straight,
for tubing O.D.  8 mm, 10 mm, 12 mm, Ć, y†,
½†, adapter for thread G¼
12/14
Pilot air supply
–
–
82/84
Pilot exhaust air
–
–
1
Air/vacuum supply
–
–
3
Exhaust air
–
–
5
Exhaust air
–
–
12/14
Pilot air supply
Thread M7
82/84
Pilot exhaust air
Thread M7
QSM-M7, straight or angled,
for tubing O.D.  4 mm, 6 mm, ¼†
è Internet: www.festo.com/catalog/...
21
Valve terminals MPA-L
Key features – Pneumatic components
Creating pressure zones and separating exhaust air
MPA-L offers a number of options
for creating pressure zones if differ­
ent working pressures are required.
Up to nine pressure zones in total
are possible.
Pressure zones are created by isol­
ating the internal supply ducts in a
special sub-base. Each pressure
zone must have its own compressed
air supply.
Compressed air can be supplied
and vented via a supply module
and/or the right-hand end plate.
Creating pressure zones
Sub-bases with pressure zone separation
Illustrated examples
22
The position of the supply modules
and the sub-bases with pressure
zone separation can be freely
chosen with the valve terminal
MPA-L.
The sub-bases with pressure zone
separation are integrated in the ter­
minal ex-works as per your order.
They can be distinguished by their
coding, even when the valve ter­
minal is assembled. Duct separa­
tion always takes place to the right
of the sub-base.
Code
Notes
Duct separation to the
right of sub-base 1 - 40: –
No duct separation
Duct separation to the
right of sub-base 1 - 40: T
Duct 1 separated
VMPAL-…-T1
Duct separation to the
right of sub-base 1 - 40:
TR
Duct 3/5 separated
VMPAL-…-T35
Duct separation to the
right of sub-base 1 - 40:
TS
Ducts 1 and 3/5 separated
VMPAL-…-T135
Coding
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
Examples: Compressed air supply and pilot air supply
Internal pilot air supply, right-hand end plate without supply ports
The illustration opposite shows an
example of the configuration and
connection of the air supply with
internal pilot air supply.
The exhaust air (duct 3/5) is
discharged via supply modules.
The pilot exhaust air (duct 82/84) is
discharged via the right-hand end
plate.
Special sub-bases are used to create
pressure zones.
External pilot air supply, right-hand end plate without supply ports
The illustration opposite shows an
example of the configuration and
connection of the compressed air
supply with external pilot air supply.
Port 12/14 on the right-hand end
plate is equipped with a fitting for
this.
The exhaust air (duct 3/5) is
discharged via supply modules.
The pilot exhaust air (duct 82/84) is
discharged via the right-hand end
plate.
Special sub-bases are used to create
pressure zones.
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
23
Valve terminals MPA-L
Key features – Pneumatic components
Sub-base
MPA-L is based on a modular system
consisting of sub-bases and valves.
The sub-bases are connected together
using tie rods and thus form the
support system for the valves.
They contain the connection ducts for
supplying compressed air to and
venting from the valve terminal as
well as the working lines for the
pneumatic drives for each valve.
Sub-base variants
Illustration
Code
Type
Notes
–
VMPAL-AP-10
VMPAL-AP-14
VMPAL-AP-20
VMPAL-AP-…-QS
Working lines 2, 4 on the sub-base
Without electrical interlinking module
VMPAL-AP-…-T1
VMPAL-AP-…-T35
VMPAL-AP-…-T135
Combination
manifold block: Z
24
The sub-bases are joined together via
tie rods. The tie rod consists of a
threaded rod, threaded sleeve and
screw.
In principle, sub-bases have a
modular structure. If this modularity
is not required within a terminal, then
four individual sub-bases can be
combined with a 4-way electrical
interlinking module to save costs.
VMPAL-AP-4x10
è Internet: www.festo.com/catalog/...
The threaded rod/sleeve combination
is selected as appropriate to the
number and width of the individual
sub-bases or sub-base combination.
To add further blocks, simply loosen
the tie rod and adapt with extenders.
There are no restrictions on
extensions; a tie rod could be made
almost entirely from extenders.
Working lines 2, 4 on the sub-base
With electrical interlinking module
Working lines 2, 4 on the sub-base
With/without electrical interlinking module
Duct separation in duct 1
Working lines 2, 4 on the sub-base
Without electrical interlinking module
Duct separation in ducts 3 and 5
Working lines 2, 4 on the sub-base
Without electrical interlinking module
Duct separation in ducts 1, 3 and 5
Working lines 2, 4 on the sub-base
With/without electrical interlinking module
No duct separation
Four-valve unit, not suitable for pressure zone separation
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Pneumatic components
Electrical interlinking module
Illustration
2015/03 – Subject to change
Code
Type
No. of solenoid coils
(valve positions)
Notes
Type of module
block 1-40: A
Type of module
block 1-40: E
Type of module
block 1-40: B
Type of module
block 1-40: C
Type of module
block 1-40: F
Type of module
block 1-40: D
Type of module
block 1-40: A
VMPAL-EVAP-10-…-2
2 (1), double solenoid
Each solenoid coil must be assigned to a specific pin
of the multi-pin plug for the valve to be actuated.
Regardless of whether blanking plates or valves are
used, valve positions occupy
one coil/address (single solenoid valves)
two coils/addresses (double solenoid valves)
Type of module
block 1-40: E
VMPAL-EVAP-14-2-4
Type of module
block 1-40: C
VMPAL-EVAP-10-1-4
Type of module
block 1-40: F
VMPAL-EVAP-14-1-4
Type of module
block 1-40: U
VMPAL-EVAP-20-SP
VMPAL-EVAP-14-…-2
VMPAL-EVAP-20-…-2
VMPAL-EVAP-10-…-1
1 (1), single solenoid
The electrical interlinking modules are colour-coded:
Single solenoid – grey
Double solenoid – black
VMPAL-EVAP-14-…-1
VMPAL-EVAP-20-…-1
VMPAL-EVAP-10-2-4
8 (4), double solenoid
4 (4), single solenoid
Each solenoid coil must be assigned to a specific pin
of the multi-pin plug for the valve to be actuated.
Regardless of whether blanking plates or valves are
used, valve positions occupy
one coil/address (single solenoid valves)
two coils/addresses (double solenoid valves)
The electrical interlinking modules are colour-coded:
Single solenoid – grey
Double solenoid – black
–
Electrical interlinking module for power supply
module
è Internet: www.festo.com/catalog/...
25
Valve terminals MPA-L
Key features – Assembly
Valve terminal assembly
Sturdy terminal assembly thanks to:
Four through-holes for wall
mounting
Additional mounting brackets
H-rail mounting
-H-
Note
If the terminal is subject to strong
vibrations or shock loads, use
additional mounting brackets of the
type VMPAL-BD for wall mounting.
These should be attached to the valve
terminal every 13 cm (one mounting
bracket every 10 valve positions).
The MPA-L valve terminal is screwed
onto the mounting surface using four
M4 or M6 screws. The mounting holes
are on the multi-pin plug connection
and on the right-hand end plate.
Optional mounting brackets are also
available.
The MPA-L valve terminal is screwed
onto the mounting surface using four
M4 and two M6 screws or using six
M6 screws. The mounting holes are
on the left-hand and right-hand end
plate and on the pneumatic interface.
Optional mounting brackets are also
available.
The MPA-L valve terminal is
attached to the H-rail (see arrow A).
The terminal is then swivelled onto
the H-rail and secured in place with
the clamping component
(see arrow B).
The following MPA-L mounting kit is
required for H-rail mounting of the
valve terminal:
With multi-pin plug connection:
CPX-CPA-BG-NRH
With fieldbus connection
(CPX terminal):
VMPAF-FB-BG-NRH
This enables mounting of the valve
terminal on an H-rail to EN 60715.
Wall mounting – Multi-pin plug connection
Wall mounting – Fieldbus connection (CPX terminal)
H-rail mounting
A
B
-H-
Note
The mounting kits (see above) only
lock the valve terminal in horizontal
mounting position.
26
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Assembly
Tie rod
Design
1
2
3
4
1
2
3
4
Threaded rod
Tie rod extender
Sleeve
Screw
Mode of operation
The tie rod for MPA-L consists of four
parts:
Threaded rod
Tie rod extender
Sleeve
Screw
This enables valve terminals of any
length to be created.
The tie rod and valve terminal are
assembled in just four steps:
2015/03 – Subject to change
Screw the threaded rods to the
left-hand end plate
Screw the sleeves to the threaded
rods
Push the sub-bases and supply
modules onto the rod/sleeve
combination
Push on the right-hand end plate
and secure with screws that engage
into the sleeves
The tie rod enables subsequent
extension of the valve terminal. This is
done by loosening the tie rod screws
and disassembling the relevant
components. The additional sub-base
or supply module is inserted at the
required location. The previously
disassembled components are then
re-assembled.
è Internet: www.festo.com/catalog/...
To compensate for the change in
length, the tie rod must be extended
by the increase in length. This is done
by screwing in extenders between the
threaded rod and sleeve. There are
suitable extenders for each sub-base,
combination of four sub-bases and
supply module.
27
Valve terminals MPA-L
Key features – Assembly
Tie rod – Components and design
Tie rod (threaded rod)
The threaded rod is used to create a
cost-optimised fixed-grid tie rod. The
threaded rod is required with valve
terminal lengths exceeding
42.45 mm, for example at least four
sub-bases (10.7 mm each), since only
the combination of a threaded rod
and sleeve offers the optimum
compensation of tolerances (by
compressing the seals between the
sub-bases).
Tie rod extender
The valve terminal can be extended
almost infinitely using tie rod
extenders.
The tie rod extenders are inserted
between the threaded rod and sleeve
and are available in appropriate
lengths for sub-bases and supply
modules.
Sleeve
Screw
The primary purpose of the sleeve is
to compensate tolerances that occur,
for example, when the seals are
compressed between the sub-bases
during assembly.
The sleeves come in different lengths,
tailored to the use of a tie rod in a
fixed grid as well as generally for the
modular tie rods.
The entire valve terminal is clamped
via the tie rod using screws.
Tolerances that occur, for example,
when the seals are compressed
between the sub-bases during
assembly, are compensated by the
interaction of the screws and sleeve.
Tie rods can be made entirely using tie
rod extenders. The threaded rod and
sleeve are required to compensate
tolerances that occur, for example,
when the seals are compressed
between the sub-bases during
assembly.
The tie rod extenders are inserted
between the threaded rod and sleeve.
They are available in suitable lengths
for sub-bases and supply modules.
The fixed-grid tie rod minimises
assembly costs when assembling
previously defined valve terminals.
These valve terminals can be
extended at any time.
The threaded rod (and if applicable
also the sleeve) must be replaced if
the valve terminal length is reduced.
Width 10 mm
Valve terminals with two valve
positions and without a supply
module are connected solely using
screws
Valve terminals with three valve
positions and without a supply
module (or with one valve position
and one supply module) are
connected using a 10 mm tie rod
extender and screw
Width 14 mm
Valve terminals with two valve
positions and without a supply
module are connected using a
10 mm tie rod extender and screw
Individual modular tie rod
Fixed-grid tie rod with extension
Fixed-grid tie rod
Short valve terminal
Valve terminals with a small number
of valve positions are created by
means of the following combinations:
28
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Assembly
Ordering data – Fixed-grid tie rod
Reference length
Part No.
L = 10.65 x V + 14.85 x W + 21.15 x Z + 21.15 x S
42.3 … 62.65
62.66 … 72.30
72.31 … 81.95
81.96 … 91.60
91.61 … 101.25
101.26 … 110.90
110.91 … 120.55
120.56 … 130.20
130.21 … 139.85
139.86 … 149.50
149.51 … 159.50
159.51 … 169.15
169.16 … 178.80
178.81 … 188.45
188.46 … 198.10
198.11 … 207.75
207.76 … 217.40
217.41 … 227.05
227.06 … 236.70
236.71 … 246.35
246.36 … 256.00
256.01 … 266.00
266.01 … 275.65
275.66 … 285.30
285.31 … 294.95
294.96 … 304.60
304.61 … 314.25
314.26 … 323.90
323.91 … 333.55
333.56 … 343.20
343.21 … 352.85
352.86 … 362.50
362.51 … 372.50
372.51 … 382.50
382.51 … 392.50
392.51 … 402.50
402.51 … 412.50
412.51 … 422.50
422.51 … 432.50
432.51 … 442.50
442.51 … 452.50
452.51 … 462.50
462.51 … 472.50
472.51 … 482.50
482.51 … 492.50
492.51 … 502.50
502..51 … 512.50
512.51 … 522.50
Tie rod
561116
561116
561116
561116
561117
561117
561117
561117
561118
561118
561118
561118
561119
561119
561119
561119
561120
561120
561120
561120
561121
561121
561121
561121
561122
561122
561122
561122
561123
561123
561123
561123
561124
561124
561124
561124
561125
561125
561125
561125
561126
561126
561126
561126
561127
561127
561127
561127
V
W
Z
S
Type
Part No.
Type
VMPAL-ZAS-5
VMPAL-ZAS-5
VMPAL-ZAS-5
VMPAL-ZAS-5
VMPAL-ZAS-45
VMPAL-ZAS-45
VMPAL-ZAS-45
VMPAL-ZAS-45
VMPAL-ZAS-85
VMPAL-ZAS-85
VMPAL-ZAS-85
VMPAL-ZAS-85
VMPAL-ZAS-125
VMPAL-ZAS-125
VMPAL-ZAS-125
VMPAL-ZAS-125
VMPAL-ZAS-165
VMPAL-ZAS-165
VMPAL-ZAS-165
VMPAL-ZAS-165
VMPAL-ZAS-205
VMPAL-ZAS-205
VMPAL-ZAS-205
VMPAL-ZAS-205
VMPAL-ZAS-245
VMPAL-ZAS-245
VMPAL-ZAS-245
VMPAL-ZAS-245
VMPAL-ZAS-285
VMPAL-ZAS-285
VMPAL-ZAS-285
VMPAL-ZAS-285
VMPAL-ZAS-325
VMPAL-ZAS-325
VMPAL-ZAS-325
VMPAL-ZAS-325
VMPAL-ZAS-365
VMPAL-ZAS-365
VMPAL-ZAS-365
VMPAL-ZAS-365
VMPAL-ZAS-405
VMPAL-ZAS-405
VMPAL-ZAS-405
VMPAL-ZAS-405
VMPAL-ZAS-445
VMPAL-ZAS-445
VMPAL-ZAS-445
VMPAL-ZAS-445
Sleeve
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
Number of valve positions in width 10 mm
Number of valve positions in width 14 mm
Number of valve positions in width 20 mm
Number of supply modules
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
29
Valve terminals MPA-L
Key features – Assembly
Ordering data – Fixed-grid tie rod
Reference length
Part No.
L = 10.65 x V + 14.85 x W + 21.15 x Z + 21.15 x S
522.51 … 532.50
532.51 … 542.50
542.51 … 552.50
552.51 … 562.50
562.51 … 572.50
572.51 … 582.50
582.51 … 592.50
592.51 … 602.50
602.51 … 612.50
612.51 … 622.50
622.51 … 632.50
632.51 … 642.50
642.51 … 652.50
652.51 … 662.50
662.51 … 672.50
672.51 … 682.50
682.51 … 692.50
692.51 … 702.50
702.51 … 712.50
712.51 … 722.50
722.51 … 732.50
732.51 … 742.50
742.51 … 752.50
752.51 … 762.50
762.51 … 772.50
772.51 … 782.50
782.51 … 792.50
792.51 … 802.50
802.51 … 812.50
812.51 … 822.50
822.51 … 832.50
832.51 … 842.50
842.51 … 852.50
852.51 … 862.50
Tie rod
561128
561128
561128
561128
561129
561129
561129
561129
561130
561130
561130
561130
561131
561131
561131
561131
561132
561132
561132
561132
561133
561133
561133
561133
561134
561134
561134
561134
561175
561175
561175
561175
561176
561176
V
W
Z
S
30
Type
Part No.
Type
VMPAL-ZAS-485
VMPAL-ZAS-485
VMPAL-ZAS-485
VMPAL-ZAS-485
VMPAL-ZAS-525
VMPAL-ZAS-525
VMPAL-ZAS-525
VMPAL-ZAS-525
VMPAL-ZAS-565
VMPAL-ZAS-565
VMPAL-ZAS-565
VMPAL-ZAS-565
VMPAL-ZAS-605
VMPAL-ZAS-605
VMPAL-ZAS-605
VMPAL-ZAS-605
VMPAL-ZAS-645
VMPAL-ZAS-645
VMPAL-ZAS-645
VMPAL-ZAS-645
VMPAL-ZAS-685
VMPAL-ZAS-685
VMPAL-ZAS-685
VMPAL-ZAS-685
VMPAL-ZAS-725
VMPAL-ZAS-725
VMPAL-ZAS-725
VMPAL-ZAS-725
VMPAL-ZAS-765
VMPAL-ZAS-765
VMPAL-ZAS-765
VMPAL-ZAS-765
VMPAL-ZAS-805
VMPAL-ZAS-805
Sleeve
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
Number of valve positions in width 10 mm
Number of valve positions in width 14 mm
Number of valve positions in width 20 mm
Number of supply modules
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Display and operation
Display and operation
Signal status display
Manual override
Each solenoid coil is allocated an LED
that indicates its signal status.
Indicator 12 shows the switching
status of the coil for duct 2
Indicator 14 shows the switching
status of the coil for duct 4
The manual override (MO) enables the
valve to be actuated when not
electrically activated or energised.
The valve is switched by pushing the
manual override.
Alternatives:
A cover cap (code N, code y or as
accessory) enables the manual
override to be actuated by pressing
it using an appropriate tool.
A cover cap (code V) can be fitted
over the manual override to prevent
it from being accidentally actuated.
Pneumatic connection and control elements
2
1
3
4
5
6
5
Manual override (MO)
MO with automatic return (non-detenting)
1
2015/03 – Subject to change
2
1 Press in the stem of the MO with
a pointed object or screwdriver.
Pilot valve switches and actuates
the main valve.
2 Remove the pointed object or
screwdriver.
Spring force pushes the stem of
the MO back.
Pilot valve returns to its initial
position and so too the single
solenoid main valve (not with
double solenoid valve code J).
1 Flat plate silencer, duct 3/5
2 Manual override
(for each pilot solenoid coil,
non-detenting or
non-detenting/detenting)
3 Ducted exhaust air, duct 3/5
4 Ports 12/14 for external pilot air
supply and 82/84 for pilot
exhaust air in the right-hand end
plate (depending on version also
ducts 1, 3 and 5)
5 Supply port, duct 1
6 Working lines, ducts 2 and 4, for
each valve position
-H-
Note
A valve actuated manually (by
means of the manual override)
cannot be reset electrically.
Conversely, an electrically actuated
valve cannot be reset using the
manual override.
MO set via turning (detenting)
1
2
è Internet: www.festo.com/catalog/...
1 Press in the stem of the MO with
a pointed object or screwdriver
until the valve switches and then
turn the stem clockwise by 90°
until the stop is reached.
Valve remains switched.
2 Turn the stem anti-clockwise by
90° until the stop is reached and
then remove the pointed object
or screwdriver. Spring force
pushes the stem of the MO back.
Valve returns to its initial
position (not with double
solenoid valve code J).
31
Valve terminals MPA-L
Key features – Electrical components
Manual override (MO)
MO with cover cap, non-detenting
MO with cover cap, detenting without accessories, mounting
Manual override is actuated by
pushing it with a pointed object or
screwdriver and reset by spring
force (detenting position prevented
due to cover cap).
Clip cover onto pilot valve.
The MO is then actuated by moving
the slide on the cover cap.
MO with cover cap, detenting without accessories, actuation
Moving the slide on the cover cap in
the direction of the arrow has the
following effect:
Slide locks into the end position
Pilot valve switches and actuates
the main valve
Moving the slide on the cover cap in
the direction of the arrow has the
following effect:
Slide locks into the end position
Spring force pushes the stem of
the MO back.
Pilot valve returns to its initial
position and so too the single
solenoid main valve (not with
double solenoid valve code J)
Inscription system
Inscription area
approx. 20 x 45 mm
A holder VMPAL-ST-AP-10
(Part No. 561109) with inscription
labels (Part No. 18576, IBS-6x10) can
be mounted on each sub-base for
labelling the valves.
Large inscription labels can be
attached to the pneumatic interface as
an alternative or in addition to the
smaller labels.
Each solenoid coil is protected with a
spark arresting protective circuit as
well as against polarity reversal.
All valve types are additionally
equipped with integrated current
reduction.
MPA-L valves are supplied with
operating voltage in the range
21.6 … 26.4 V (24 V +/–10%).
IBS-6x10
VMPAL-ST-AP-10
Electrical power as a result of current reduction
Power management
32
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Electrical components
Electrical connection – Left-hand end plate
The electrical connection for
connecting the valves to a higher-level
controller is located in the left-hand
end plate.
The different connection options can
be easily switched by replacing the
left-hand end plate, while the
pneumatic connections remain as
they are.
The valves are switched by means of
positive or negative logic (PNP or
NPN). Mixed operation is not
permitted.
Guidelines on addressing for valves/solenoid coils
The numbering of the addresses
goes from left to right in ascending
consecutive order. The following
applies to the individual valve
positions: address x for coil 14 and
address x+1 for coil 12.
Left-hand end plate variants
Illustration
Each sub-base/electrical
interlinking module occupies a
defined number of addresses/pins:
– For single solenoid valve: 1
– For double solenoid valve: 2
– For combination of four
sub-bases for single solenoid
valves: 4
– For combination of four
sub-bases for double solenoid
valves: 8
-H-
Note
If a single solenoid valve is
assembled on a double solenoid
valve position, the second address
(for coil 12) is also occupied and
cannot be used.
Code
Type
Max. no. of
addresses
Protection
class
Notes
Electrical
connection: MS1
Electrical
connection: MS2
Electrical
connection: MS6
Electrical
connection: MS8
Electrical
connection: MF1
VMPAL-EPL-SD25-IP40
24
IP40
Electrical connection via Sub-D, 25-pin
VMPAL-EPL-SD9-IP40
8
IP40
Electrical connection via Sub-D, 9-pin
VMPAL-EPL-SD25
24
IP65
Electrical connection via Sub-D, 25-pin
VMPAL-EPL-SD44
32
IP65
Electrical connection via Sub-D, 44-pin
VMPAL-EPL-FL40-IP40
32
IP40
Electrical connection via flat cable, 40-pin
Electrical
connection: MC
VMPAL-EPL-KL33-IP40
32
IP40
Electrical connection via terminal strip, 33-pin
VMPAL-EPL-CPX
32
IP67
Electrical connection via CPX interlinking mod­
ule
Electrical
connection: LK
VMPAL-EPL-IPO32
32
IP65
Electrical connection via M12, 5 pin,
IO-Link
Electrical
connection: PT
VMPAL-EPL-IPO32
32
IP65
Electrical connection via M12, 5 pin,
I-Port interface
Electrical multi-pin connection
Fieldbus connection/CPX terminal
Electrical
connection: CX
I-Port interface/IO-Link
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
33
Valve terminals MPA-L
Key features – Electrical components
Pin allocation for electrical multi-pin plug connection – Sub-D plug, 9-pin
Pin Address/coil
1)
Pin Address/coil
1
0
6
5
2
1
7
6
3
2
8
7
4
3
9
0 V1)
5
4
-H-
Note
The drawing shows the view onto the
pins of the Sub-D plug.
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
Pin allocation for electrical multi-pin plug connection – Sub-D plug, 25-pin, connecting cable VMPAL-KM
Pin Address/ Connecting cable
Pin Address/ Connecting cable
coil
wire colour2)
coil
wire colour2)
1)
2)
1
0
WH
14
13
BN YE
2
1
GN
15
14
GY WH
3
2
YE
16
15
BN GY
4
3
GY
17
16
WH PK
5
4
PK
18
17
BN PK
6
5
BU
19
18
BU WH
7
6
RD
20
19
BN BU
8
7
VT
21
20
RD WH
9
8
GY PK
22
21
BN RD
10
9
RD BU
23
22
BK WH
11
10
GN WH
24
23
BN
12
11
BN GN
25
0 V1)
BK
13
12
YE WH
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
34
Note
The drawing shows the view onto the
pins of the Sub-D plug.
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
To IEC 757
Pin allocation for electrical multi-pin plug connection – Sub-D plug, 44-pin, connecting cable VMPAL-KM
Pin Address/ Connecting cable
Pin Address/ Connecting cable
coil
wire colour2)
coil
wire colour2)
1)
2)
-H-
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WH
GN
YE
GY
PK
BU
RD
VT
GY PK
RD BU
GN WH
BN GN
YE WH
BN YE
GY WH
BN GY
WH PK
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
n.c.
n.c.
BN PK
BU WH
BN BU
RD WH
BN RD
BK WH
BN
BK BN
GN GY
YE GY
GN PK
YE PK
GN BU
YE BU
RD GN
n.c.
n.c.
Pin Address/
coil
Connecting cable
wire colour2)
35
36
37
38
39
40
41
42
43
44
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
RD YE
BK GN
BK YE
BK
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
0 V1)
0 V1)
0 V1)
0 V1)
-H-
Note
The drawing shows the view onto the
pins of the Sub-D plug.
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
To IEC 757
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Electrical components
Electrical multi-pin connection – Ordering data
Designation
Code
Description
Connecting cable for multi-pin plug connection with Sub-D plug socket
Connecting cable: CA
Cable outlet to front
Connecting cable: CB (only with electrical connection
code: MS6)
Connecting cable: CC
Connecting cable: –
Connecting cable: CQ Cable outlet to front
(only with electrical connection
Connecting cable: CR
code: MS6)
Connecting cable: CS
Suitable for use with energy chains
Connecting cable: –
Connecting cable: CJ
Cable outlet to front
(only with electrical connection
Connecting cable: CK
code: MS8)
Connecting cable: CL
Connecting cable: –
Connecting cable: CD Cable outlet to side
(only with electrical connection
Connecting cable: CE
Connecting cable: CH code: MS6)
Connecting cable: –
Connecting cable: CT
Cable outlet to side
Connecting cable: CU (only with electrical connection
code: MS6)
Connecting cable: CV
Suitable for use with energy chains
Connecting cable: –
Connecting cable: CM
Connecting cable: CN
Connecting cable: CP
Connecting cable: –
Cable outlet to side
(only with electrical connection
code: MS8)
Connection Cable length
Part No.
Type
25-pin
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
560416
560417
560418
562389
560410
560411
560412
562391
560422
560423
560424
562390
560419
560420
560421
562392
560413
560414
560415
562394
560425
560426
560427
562393
VMPAL-KM-V-SD25-IP67-2,5
VMPAL-KM-V-SD25-IP67-5
VMPAL-KM-V-SD25-IP67-10
VMPAL-KM-V-SD25-IP67-X
VMPAL-KMSK-V-SD25-IP67-2,5
VMPAL-KMSK-V-SD25-IP67-5
VMPAL-KMSK-V-SD25-IP67-10
VMPAL-KMSK-V-SD25-IP67-X
VMPAL-KM-V-SD44-IP67-2,5
VMPAL-KM-V-SD44-IP67-5
VMPAL-KM-V-SD44-IP67-10
VMPAL-KM-V-SD44-IP67-X
VMPAL-KM-S-SD25-IP67-2,5
VMPAL-KM-S-SD25-IP67-5
VMPAL-KM-S-SD25-IP67-10
VMPAL-KM-S-SD25-IP67-X
VMPAL-KMSK-S-SD25-IP67-2,5
VMPAL-KMSK-S-SD25-IP67-5
VMPAL-KMSK-S-SD25-IP67-10
VMPAL-KMSK-S-SD25-IP67-X
VMPAL-KM-S-SD44-IP67-2,5
VMPAL-KM-S-SD44-IP67-5
VMPAL-KM-S-SD44-IP67-10
VMPAL-KM-S-SD44-IP67-X
–
560428
VMPAL-KM-SD25-IP67-0
–
560429
VMPAL-KM-SD44-IP67-0
25-pin
44-pin
25-pin
25-pin
44-pin
Cover for multi-pin plug connection without connecting cable with Sub-D plug socket
Connecting cable: EZ
Cable outlet to side or front
25-pin
(only with electrical connection
code: MS6)
Connecting cable: EY
Cable outlet to side or front
44-pin
(only with electrical connection
code: MS8)
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
35
Valve terminals MPA-L
Key features – Electrical components
Pin allocation for electrical multi pin-plug connection – Flat cable, 40-pin
Pin Address/coil
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
36
Pin Address/coil
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0 V1)
0 V1)
0 V1)
0 V1)
0 V1)
0 V1)
0 V1)
0 V1)
-H-
Note
The drawing shows the view onto the
pins of the flat cable plug.
The flat cable connection is
established using plug connectors,
in accordance with
DIN EN 60603-13:1998-09
(NECU-FCG40-K).
è Internet: necu
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
Pin allocation for electrical multi pin-plug connection – Terminal strip, 33-pin
Pin Address/coil
1)
Pin Address/coil
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Pin Address/coil
Pin Address/coil
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0 V1)
-H-
Note
The drawing shows the view onto the
pins of the terminal strip.
Cables with the following
specifications can be connected:
Cable cross section
0.08 … 0.5 mm2
Insulation 5 … 6 mm
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Key features – Electrical components
Fieldbus connection/CPX terminal
All functions and features of the
electrical peripherals CPX are
permitted in connection with the CPX
interface.
This means:
The valves and outputs are supplied
via the system supply for the CPX
terminal
The valves can optionally be
actuated or switched off separately
from the outputs
The pneumatic interface (left-hand
end plate) serves as an adapter
between the two current feeds.
In the pneumatic interface, the serial
signals from the CPX terminal are
converted into parallel signals.
The number of addresses (solenoid
coils that can be connected) is set via
a selector (rotary switch) on the
pneumatic interface to between
4 … 32 solenoid coils. The default
setting on delivery provides for
32 addresses. This enables extensions
to be pre-assigned in a control
program and called up by means of
manual settings.
After converting or extending the valve
terminal, the number of output
addresses occupied by the pneumatic
components must be checked and if
applicable adjusted.
-H-
IO-Link master
The maximum distance between the
I-Port/IO-Link master and valve
terminal with I-Port interface/IO-Link
is 20 m.
The 5-pin connecting cables contain
the power supply for the valves,
separate from this is the power supply
for the internal valve terminal
electronics and the control signals.
-H-
Note
More information can be found at:
è Internet: cpx
I-Port interface/IO-Link
The I-Port interface/IO-Link enables
the valve terminal CPV to be
connected to the following systems:
I-Port master from Festo
(CPX terminal, CECC)
Fieldbus node CTEU from Festo
Note
More information can be found at:
è Internet: cteu
Pin allocation I-Port interface/IO-Link
2015/03 – Subject to change
Pin
Designation
1
24 V DC supply voltage for electronics and inputs
2
24 V DC load voltage supply for valves and outputs
3
0 V DC supply voltage for electronics and sensors
4
Communication signal C/Q, data cable
5
0 V DC load voltage supply for valves and outputs
è Internet: www.festo.com/catalog/...
37
Valve terminals MPA-L
Key features – Electrical components
Instructions for use
Equipment
Operate system equipment with
unlubricated compressed air if
possible. Festo valves and cylinders
are designed so that, if used as
designated, they will not require
additional lubrication and will still
achieve a long service life.
The quality of compressed air
downstream of the compressor must
correspond to that of unlubricated
compressed air. If possible, do not
operate all of your system equipment
with lubricated compressed air. The
lubricators should, where possible,
always be installed directly upstream
of the actuator used.
38
Bio-oils
Unsuitable additional oil and too high
an oil content in the compressed air
reduce the service life of the valve
terminal.
Use Festo special oil OFSW-32 or the
alternatives listed in the Festo
catalogue (as specified in DIN 51524
HLP32; basic oil viscosity 32 CST
at 40 °C).
è Internet: www.festo.com/catalog/...
When using bio-oils (oils which are
based on synthetic or native ester,
e.g. rapeseed oil methyl ester), the
maximum residual oil content of
0.1 mg/m3 must not be exceeded
(see ISO 8573-1 Class 2).
Mineral oils
When using mineral oils (e.g. HLP oils
to DIN 51524, parts 1 to 3) or similar
oils based on poly-alpha-olefins
(PAO), the maximum residual oil
content of 5 mg/m3 must not be
exceeded (see ISO 8573-1 Class 4).
A higher residual oil content
irrespective of the compressor oil
cannot be permitted, as the basic
lubricant would be flushed out over
time.
Subject to change – 2015/03
Valve terminals MPA-L
Technical data
-M-K-
-P-
Flow rate
Up to 870 l/min
Valve width
10 mm
14 mm
20 mm
Voltage
24 V DC
General technical data
Valve terminal design
Electrical actuation
Type of actuation
Nominal operating voltage
[V DC]
Max. no. of valve positions
Max. number of pressure zones
Valve size
[mm]
Switching position display
Pilot air supply
Lubrication
Type of mounting
Mounting position
Manual override
Corrosion resistance class CRC1)
Note on materials
Degree of protection
1)
Modular, valve sizes can be mixed
Fieldbus
Multi-pin plug
IO-Link
Electrical
24
32
9
10, 14, 20
LED
Internal or external
Life-time lubrication, PWIS-free (free of paint-wetting impairment substances)
Wall mounting
On H-rail to EN 60715
Any (wall mounting)
Horizontal only (H-rail)
Non-detenting, detenting
3
RoHS-compliant
IP65, IP67
I-Port
Corrosion resistance class 3 according to Festo standard 940 070
Components subject to high corrosion stress. Externally visible parts with primarily functional surface requirements which are in direct contact with the surrounding industrial environment or media such as solvents
and cleaning agents.
Operating and environmental conditions
Operating medium
Note on operating/
pilot medium
Operating pressure
Pilot pressure
Ambient temperature
Temperature of medium
Storage temperature1)
Certification
1)
Compressed air to ISO 8573-1:2010 [7:4:4]
Lubricated operation possible (in which case lubricated operation will always be required)
[bar]
[bar]
[°C]
[°C]
[°C]
–0.9 … +10
3…8
–5 … +50
–5 … +50
–20 … +40
RCM trademark
Long-term storage
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
39
Valve terminals MPA-L
Technical data
Technical data – Valve width 10 mm
Code for position function 1-32
Design
Sealing principle
Non-overlapping
Reset method
Switching times
On
Off
Change­
over
Standard nominal flow rate
Operating pressure
Pilot pressure
Max. tightening torque of valve
mounting
Materials
Product weight
M
J
N
[ms]
[ms]
[ms]
Piston spool valve
Soft
Yes
Pneumatic spring
10
20
–
–
10
–
15
Pneumatic spring
10
10
10
20
20
20
–
–
–
Mechanical spring
10
10
10
35
35
35
15
15
15
Pneumatic spring
10
10
10
20
20
20
–
–
–
[l/min]
[bar]
[bar]
[Nm]
360
–0.9 … +10
3…8
0.25
360
300
230
3 … 10
300
300
320
–0.9 … +10
240
255
255
–0.9 … +10
230
260
3 … 10
[g]
Die-cast aluminium
49
56
56
56
56
56
49
56
Technical data – Valve width 10 mm
Code for position function 1-32
Design
Sealing principle
Non-overlapping
Reset method
Switching times
On
Off
Change­
over
Standard nominal flow rate
Operating pressure
Pilot pressure
Max. tightening torque of valve
mounting
Materials
Product weight
MS
NS
[ms]
[ms]
[ms]
Piston spool valve
Soft
Yes
Mechanical spring
10
14
27
16
–
–
[l/min]
[bar]
[bar]
[Nm]
360
–0.9 … +8
3…8
0.25
[g]
Die-cast aluminium
56
M
Design
Sealing principle
Non-overlapping
Reset method
Piston spool valve
Soft
Yes
Pneumatic spring
Switching times
On
Off
Change­
over
Standard nominal flow rate
Operating pressure
Pilot pressure
Max. tightening torque of valve
mounting
Materials
Product weight
40
J
9
–
24
N
12
38
–
H
56
KS
300
Technical data – Valve width 14 mm
Code for position function 1-32
K
HS
B
G
E
56
X
W
49
DS
MU
Poppet valve with spring return
Soft
No
Mechanical spring
10
8
8
12
8
10
–
–
–
14
16
–
14
16
–
14
16
–
230
300
230
NU
KU
190
190
–0.9 … +10
4…8
0.25
Reinforced PPA
35
42
K
12
38
–
H
B
12
38
–
Mechanical
spring
16 13
13
50 52 50
26 26
26
[ms]
[ms]
[ms]
13
30
–
[l/min]
[bar]
[bar]
[Nm]
670 670 650 600 650
–0.9 … +10 3 … 10
3…8
0.65
[g]
Die-cast aluminium
77
G
E
X
W
D
I
Pneumatic spring
12
20
–
12
20
–
12
30
–
MS
I
8
20
–
56
HU
8
10
–
160
190
42
42
NS
KS
HS
DS
12
23
–
12
23
–
10
25
–
560
520
570
Mechanical spring
10
28
–
13
30
–
12
23
–
630 610 480 400 400 650 670 670
520
–0.9 … +10
–0.9 … +10 3 … 10
–0.9 … +8
3…8
0.65
0.25
è Internet: www.festo.com/catalog/...
D
Subject to change – 2015/03
Valve terminals MPA-L
Technical data
Technical data – Valve width 20 mm
Code for position function 1-32
Design
Sealing principle
Non-overlapping
Reset method
Switching times
On
Off
Change­
over
Standard nominal flow rate
Operating pressure
Pilot pressure
Max. tightening torque of valve
mounting
Materials
Product weight
M
J
N
[ms]
[ms]
[ms]
Piston spool valve
Soft
Yes
Pneumatic spring
15
9
8
28
–
28
–
22
–
[l/min]
[bar]
[bar]
[Nm]
700 860
–0.9 … +10
3…8
0.65
[g]
Die-cast aluminium
100
K
H
B
8
28
–
8
28
–
Mechanical spring
11
10
11
46
40
47
23
21
23
Pneumatic spring
13
13
7
22
22
25
–
–
–
550 750
–0.9 … +10
480 480
–0.9 … +10
610 550
3 … 10
550
G
E
700
X
W
D
I
MS
7
23
–
Mechanical spring
8
12
12
36
25
25
–
–
–
840 680
3 … 10
NS
840 620
–0.9 … +8
KS
500
HS
DS
12
25
–
12
25
–
550
820
Safety characteristics
Note on forced switch on/off
CE marking (see declaration of conformity)
Max. positive test pulse
[ìs]
with 0 signal
Max. negative test pulse
[ìs]
with 1 signal
Shock resistance
Vibration resistance
1)
Valve width 10 mm
Valve width 14 mm
Valve width 20 mm
Min. 1/week
To EU EMC Directive1)
400
400
400
200
200
900
Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27
Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6
For information about the applicability of the component see the manufacturer’s EC declaration of conformity at: www.festo.com/sp è User documentation.
If the component is subject to restrictions on usage in residential, office or commercial environments or small businesses, further measures to reduce the emitted interference may be necessary.
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
41
Valve terminals MPA-L
Technical data
Pneumatic connections
Right-hand end plate
Supply
Exhaust port
Pilot air supply
Pilot exhaust port
1
3
5
12/14
82/84
Thread G1/4 (QS-G1/4, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2")
Thread G1/4 (QS-G1/4, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2")
Thread G1/4 (QS-G1/4, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2")
Thread M7 (QSM-M7, straight or angled, for tubing O.D. 4 mm, 6 mm, 1/4")
Thread M7 (QSM-M7, straight or angled, for tubing O.D. 4 mm, 6 mm, 1/4")
Power supply module
Supply
1
Exhaust port
3/5
Cartridge fitting 20 mm (QSPKG20, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2", adapter for thread
G1/4), flat plate silencer
Cartridge fitting 20 mm (QSPKG20, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2", adapter for thread
G1/4), flat plate silencer
Vertical pressure supply plate, width 20 mm
Supply
1
Thread G1/8 (QS-G1/8, straight, for tubing O.D. 8 mm, 10 mm, 5/16", 3/8")
Sub-base width 10 mm
Working ports
Sub-base width 14 mm
Working ports
Sub-base width 20 mm
Working ports
2
4
Cartridge fitting 10 mm (QSPKG10, straight or angled, for tubing O.D. 4 mm, 6 mm, 5/32", 1/4", adapter for thread M7)
Cartridge fitting 10 mm (QSPKG10, straight or angled, for tubing O.D. 4 mm, 6 mm, 5/32", 1/4", adapter for thread M7)
2
4
Cartridge fitting 14 mm (QSPKG14, straight or angled, for tubing O.D. 6 mm, 8 mm, 1/4", 5/16", adapter for thread G1/8)
Cartridge fitting 14 mm (QSPKG14, straight or angled, for tubing O.D. 6 mm, 8 mm, 1/4", 5/16", adapter for thread G1/8)
2
Cartridge fitting 18 mm (QSPKG18, straight or angled, for tubing O.D. 8 mm, 10 mm, 5/16", 3/8", adapter for thread
G1/4)
Cartridge fitting 18 mm (QSPKG18, straight or angled, for tubing O.D. 8 mm, 10 mm, 5/16", 3/8", adapter for thread
G1/4)
4
42
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Technical data
Pilot pressure p2 as a function of working pressure p1 with external pilot air supply
For valves with code for position function 1-32: M, J, B, G, E, W, X
For valves with code for position function 1-32: N, K, H, D, I
Pilot pressure p2 as a function of working pressure p1 for valves with mechanical spring return
For valves in width 10 mm with code for position function 1-32: MS, NS, KS,
For valves in width 14 mm with code for position function 1-32: MS, NS, KS,
HS, DS
HS, DS
For valves in width 20 mm with code for position function 1-32: MS, NS, KS,
HS, DS
2015/03 – Subject to change
For valves in width 10 mm with code for position function 1-32: MU, NU, KU, HU
è Internet: www.festo.com/catalog/...
43
Valve terminals MPA-L
Technical data
Current consumption per solenoid coil at nominal voltage
Width
10 mm
Nominal pick-up current
Nominal current with current
reduction
Time until current reduction
14 mm
20 mm
[mA]
[mA]
50
10
50
10
110
23
[ms]
20
20
20
Electrical data – MPA-L with electrical interface for CPX terminal
Intrinsic current consumption of valve terminal (internal electronics, without valves)
At 24 V UEL/SEN1)
[mA]
Typically 13
At 24 V Uval2)
[mA]
Typically 35
Diagnostic message
Undervoltage UOFF3)
1)
2)
3)
[V]
17.7 … 17.8
Power supply for electronics and sensors
Load voltage supply for valves
Load voltage outside of function range
Electrical data – MPA-L with I-Port interface/IO-Link
Intrinsic current consumption of valve terminal (internal electronics, without valves)
Operating voltage
[mA]
30
Load voltage
[mA]
30
Materials
Sub-base
Power supply module
End plate
Seals
Exhaust plate
Flat plate silencer
Electrical interlinking module
Pressure regulator plate
Vertical pressure shut-off plate
Vertical pressure supply plate
44
PA
PPA
Die-cast aluminium, PA, PBT
NBR
PA
PE
PBT, PA, copper alloy
PA
Reinforced PA, wrought aluminium alloy
Reinforced PA
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Technical data
Product weight
Approx. weight [g]
CPX module (complete)
Left-hand end plate, multi-pin plug,
Sub-D, 44-pin
Left-hand end plate, I-Port interface/
IO-Link
Power supply module with seal,
electrical interlinking module
Right-hand end plate
without supply ports
Right-hand end plate
with supply ports
Valve
Power supply module with seal,
electrical interlinking module
Screw for tie rod
Threaded rods for tie rod,
5/45/85/125/165/205/245/285/325/3
65/405/445/485/525 mm
Sleeve for tie rod, 36/46/56/66 mm
Plate for ducted exhaust air/flat plate
silencer
QSM-M7-4-I
QSM-M7-6-I
QS-G¼-8-I
QS-G¼-10-I
Approx. 210
130
QSPKG10-3
QSPKG10-4
QSPKG10-6
QSPKG20-8
QSPKG20-10
QSPKG20-12
1
1
2
6
9
12
170
51
105
160
è 40
51
3
2/11/20/29/38/47/54/65/72/80/89/98/109/118
6/8/9/11
36/40
4
5
22
23
Product weight [g]
Black sub-base
(with seal, fibre-optic cable)
Electrical interlinking module for one
sub-base
Electrical interlinking module for
combination of four sub-bases
Per vacant position L
Pressure regulator plate
Vertical pressure shut-off plate
Vertical pressure supply plate
2015/03 – Subject to change
Width 10 mm
Width 14 mm
Width 20 mm
21
33
47
9
9
14
29
–
–
24
74
60
–
23
–
–
–
–
180
–
70
è Internet: www.festo.com/catalog/...
45
Valve terminals MPA-L
Technical data
Download CAD data è www.festo.com
Dimensions
Valve terminal with multi-pin plug connection
1 Solenoid valve VMPA1
2 Solenoid valve VMPA14
3 Solenoid valve VMPA2
Type
4 Manual override
5 Power supply module
6 Working ports
L11)
L21)
L31)
L41)
7 H-rail
8 H-rail mounting
9 Mounting holes
L5
L6
L7
L8
aJ Earthing screw
aA Multi-pin plug connection
L9
L10
L11
L12
L13
L14
L15
L16
14.9 21.2 8.5
6.8
6.5
5.6
1.5
1
,
MPA-L
89.10 + L2 + L3 + L4
Type
B1
B2
MPA-L
107.3
66.3
B3
m x 10.7
n x 14.9
o x 21.2
43
21.2 24.9 10.7
B4
B5
B6
B7
B8
D1
D2
H1
H2
33.5
23.5
18.9
7.5
7.5
6.6
4.4
69.6
65.7
,
1)
46
65
H3
H4
H5
H6
H7
28.5
27.9
8.5
10.9
,
36.4
m, n, o = number of sub-bases/valve positions (m = width 10 mm, n = width 14 mm, o = width 20 mm)
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Technical data
Download CAD data è www.festo.com
Dimensions
Valve terminal with fieldbus connection
1
2
3
4
5
6
7
8
Solenoid valve VMPA1
Solenoid valve VMPA14
Solenoid valve VMPA2
Manual override
9 Mounting holes
aJ Pneumatic interface, CPX ter­
minal
Power supply module
Working ports
H-rail
H-rail mounting
aA CPX module
aB Earthing screw
Type
L11)
L21)
L31)
L41)
MPA-L
170.9 + L2 + L3 + L4
m x 10.7
n x 14.9
o x 21.2
Type
L10
L11
L12
L13
L14
L15
L16
L17
L18
L19
L20
MPA-L
24
30
10.7
14.9
21.2
8.5
6.8
5.6
6.5
1.5
1
Type
B1
B2
MPA-L
124
107.3 66.3 65
L5
L6
L7
L8
L9
50
40
21.2
28.9
,
B3
B4
B5
B6
141.8
B7
B8
B9
B10
B11
D1
D2
D3
H1
33.5 23.5 15
13
7.5
5.3
5.5
6.6
4.4
7
69.6 65.7 52
,
1)
H2
H3
H4
H5
H6
H7
,
39.8 28.5 25.8 8.5
m, n, o = number of sub-bases/valve positions (m = width 10 mm, n = width 14 mm, o = width 20 mm)
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
47
Valve terminals MPA-L
Technical data
Download CAD data è www.festo.com
Dimensions
Valve terminal with I-Port interface/IO-Link
1 Solenoid valve VMPA1
2 Solenoid valve VMPA14
3 Solenoid valve VMPA2
Type
B1
B2
MPA-L
107.3
66.3
Type
L11)
4 Manual override
5 Power supply module
6 Working ports
B3
7 H-rail
8 H-rail mounting
9 Mounting holes
aJ Left-hand end plate with I-Port
interface/IO-Link
B4
B5
B6
D1
D2
D3
H1
H2
33.5
23.5
18.9
6.6
6.4
4.5
69.6
65.7
,
H3
H4
H5
H6
H7
28.5
27.9
8.5
10.9
,
65
L21)
L31)
L41)
L5
L6
L7
L8
L9
36.4
L10
L11
L12
L13
L14
L15
L16
14.9 21.2 6.2
5.7
6.5
5.6
1.5
1
,
MPA-L
1)
48
110.9 + L2 + L3 + L4
m x 10.7
n x 14.9
o x 21.2
64.8
21.2 24.9 10.7
m, n, o = number of sub-bases/valve positions (m = width 10 mm, n = width 14 mm, o = width 20 mm)
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Technical data
Download CAD data è www.festo.com
Dimensions – Cover for multi-pin plug connection
Cable outlet to front
Type
L1
Cable outlet to side
L2
H1
H2
B1
B2
B3
14
26
34.5
34.5
–
27
–
29
,
Cable outlet to front
Cable outlet to side
108.3
114.5
27
–
44.4
32.4
Valve terminal with vertical stacking (example: valve terminal with I-Port interface/IO-Link)
Type
L1
L2
L3
H1
,
VMPA…-B8-R
2015/03 – Subject to change
175.1
120.7
15
è Internet: www.festo.com/catalog/...
138.7
49
Valve terminals MPA-L
Accessories
Ordering data
Code
Valve function
Individual solenoid valve – Width 10 mm
5/2-way valve
Position function 1-32: M Single solenoid
Position function 1-32: MS Single solenoid, mechanical spring return
Position function 1-32: MU Polymer poppet valve, single solenoid,
mechanical spring return
Position function 1-32: J
Double solenoid
2x 3/2-way valve
Position function 1-32: N Normally open
Position function 1-32: NS Normally open,
mechanical spring return
Position function 1-32: NU Polymer poppet valve, normally open,
mechanical spring return
Position function 1-32: K Normally closed
Position function 1-32: KS Normally closed,
mechanical spring return
Position function 1-32: KU Polymer poppet valve, normally closed,
mechanical spring return
Position function 1-32: H 1x normally open – 1x normally closed
Position function 1-32: HS 1x normally open – 1x normally closed,
mechanical spring return
Position function 1-32: HU Polymer poppet valve,
1x normally open – 1x normally closed,
mechanical spring return
5/3-way valve
Position function 1-32: B Mid-position pressurised
Position function 1-32: G Mid-position closed
Position function 1-32: E
Mid-position exhausted
1x 3/2-way valve
Position function 1-32: W Normally open, external compressed air supply
Position function 1-32: X Normally closed, external compressed air supply
2x 2/2-way valve
Position function 1-32: D Normally closed
Position function 1-32: DS Normally closed,
mechanical spring return
Position function 1-32: I
1x normally closed
1x normally closed, reversible
Vacant position – Width 10 mm
Position function 1-32: L
50
Blanking plate for one valve position in width 10 mm
A self-adhesive label is supplied
è Internet: www.festo.com/catalog/...
Part No.
Type
533342
571334
553113
VMPA1-M1H-M-PI
VMPA1-M1H-MS-PI
VMPA1-M1H-MU-PI
533343
VMPA1-M1H-J-PI
533348
556839
VMPA1-M1H-N-PI
VMPA1-M1H-NS-PI
553111
VMPA1-M1H-NU-PI
533347
556838
VMPA1-M1H-K-PI
VMPA1-M1H-KS-PI
553110
VMPA1-M1H-KU-PI
533349
556840
VMPA1-M1H-H-PI
VMPA1-M1H-HS-PI
553112
VMPA1-M1H-HU-PI
533344
533345
533346
VMPA1-M1H-B-PI
VMPA1-M1H-G-PI
VMPA1-M1H-E-PI
540050
534415
VMPA1-M1H-W-PI
VMPA1-M1H-X-PI
533350
556841
VMPA1-M1H-D-PI
VMPA1-M1H-DS-PI
543605
VMPA1-M1H-I-PI
533351
VMPA1-RP
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Vertical stacking modules – Width 10 mm
Pressure regulator 1-32: PF
Pressure regulator 1-32: PA
Pressure regulator 1-32: PH
Pressure regulator 1-32: PC
Pressure regulator 1-32: PG
Pressure regulator 1-32: PB
Pressure regulator 1-32: PF
Pressure regulator 1-32: PA
Pressure regulator 1-32: PH
Pressure regulator 1-32: PC
Pressure regulator 1-32: PG
Pressure regulator 1-32: PB
Pressure regulator 1-32: PS
Pressure gauge 1-32: VE
Pressure gauge 1-32: VD
Pressure gauge 1-32: VC
2015/03 – Subject to change
Valve function
Pressure regulator
For port 1
plate with fixed
threaded connection For port 2
M5
For port 4
Pressure regulator
For port 1
plate with rotatable
threaded connection For port 2
M5
For port 4
0.5 … 5
0.5 … 8.5
2…5
2 … 8.5
2…5
2 … 8.5
0.5 … 5
0.5 … 8.5
2…5
2 … 8.5
2…5
2 … 8.5
Vertical pressure shut-off plate
For manually separating an individual valve from the
compressed air supply for the valve terminal (ducts 1 and
12/14 pilot air supply), operating pressure 3 … 8 bar
Screw-in pressure gauge with thread M5 for Unit bar
pressure regulator plate with rotatable
Unit psi
threaded connection
Non-return valve with thread M5 for pressure regulator plate
Part No.
Type
564911
564908
564912
564909
564913
564910
549052
543339
549053
543340
549054
543341
567805
VMPA1-B8-R1-M5-06
VMPA1-B8-R1-M5-10
VMPA1-B8-R2-M5-06
VMPA1-B8-R2-M5-10
VMPA1-B8-R3-M5-06
VMPA1-B8-R3-M5-10
VMPA1-B8-R1C2-C-06
VMPA1-B8-R1C2-C-10
VMPA1-B8-R2C2-C-06
VMPA1-B8-R2C2-C-10
VMPA1-B8-R3C2-C-06
VMPA1-B8-R3C2-C-10
VMPA1-HS
132340
MA-15-10-M5
132341
MA-15-145-M5-PSI
153291
QSK-M5-4
è Internet: www.festo.com/catalog/...
51
Valve terminals MPA-L
Accessories
Ordering data
Code
Fixed restrictor – Width 10 mm
Pneumatic connection 3,
1-40: V03
Pneumatic connection 5,
1-40: Q03
Pneumatic connection 3,
1-40: V05
Pneumatic connection 5,
1-40: Q05
Pneumatic connection 3,
1-40: V07
Pneumatic connection 5,
1-40: Q07
Pneumatic connection 3,
1-40: V10
Pneumatic connection 5,
1-40: Q10
Pneumatic connection 3,
1-40: V12
Pneumatic connection 5,
1-40: Q12
Pneumatic connection 3,
1-40: V15
Pneumatic connection 5,
1-40: Q15
Pneumatic connection 3,
1-40: V17
Pneumatic connection 5,
1-40: Q17
Restrictor set – Width 10 mm
–
Retainer for fixed restrictor – Width 10 mm
–
1)
52
Part No.
Type
PU1)
3.5 … 5.5 l/min
572544
VMPA1-FT-NW0.3-10
10
9 … 12 l/min
572545
VMPA1-FT-NW0.5-10
10
18 … 22 l/min
572546
VMPA1-FT-NW0.7-10
10
36 … 41 l/min
572547
VMPA1-FT-NW1.0-10
10
52 … 58 l/min
572548
VMPA1-FT-NW1.2-10
10
81 … 89 l/min
572549
VMPA1-FT-NW1.5-10
10
105 … 115 l/min
572550
VMPA1-FT-NW1.7-10
10
Fixed restrictor, two of each size,
two retainers and assembly tool
572543
VMPA1-FT-NW0.3-1.7
14
Retainer for exhaust opening in the sub-base
572542
VMPA1-FTI-10
10
Description
Hollow bolt, for restricting the exhaust
air
Packaging unit quantity.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Sub-base – Width 10 mm
Duct separation to the
right of sub-base 1-40: –
Duct separation to the
right of sub-base 1-40: T
Duct separation to the
right of sub-base 1-40: TR
Duct separation to the
right of sub-base 1-40: TS
–
Combination of four sub-bases – Width 10 mm
Combination manifold
block: Z
–
Electrical interlinking module – Width 10 mm
Type of module block
1-40: C
Type of module block
1-40: A
Type of module block
1-40: C
Type of module block
1-40: A
2015/03 – Subject to change
Description
Single,
without electrical
interlinking module,
without cartridge fitting
Single,
with electrical interlink­
ing module,
single solenoid
(for 1 solenoid coil),
with cartridge fitting
Part No.
Type
No duct separation
–
554311
VMPAL-AP-10
Duct 1 separated
–
554312
VMPAL-AP-10-T1
Ducts 3, 5 separated
–
554313
VMPAL-AP-10-T35
Ducts 1 and 3,
5 separated
No duct separation,
tubing O.D.
–
554315
VMPAL-AP-10-T135
4 mm
6 mm
5/32"
1/4"
4 mm
6 mm
5/32"
1/4"
4 mm
6 mm
5/32"
1/4"
4 mm
6 mm
5/32"
1/4"
560994
560987
561005
560999
561017
561011
561029
561023
560988
560993
561006
561000
561018
561012
561030
561024
VMPAL-AP-10-QS4-1
VMPAL-AP-10-QS6-1
VMPAL-AP-10-QS5/32"-1
VMPAL-AP-10-QS1/4"-1
VMPAL-AP-10-QS4-1-T1
VMPAL-AP-10-QS6-1-T1
VMPAL-AP-10-QS5/32"-1-T1
VMPAL-AP-10-QS1/4"-1-T1
VMPAL-AP-10-QS4-2
VMPAL-AP-10-QS6-2
VMPAL-AP-10-QS5/32"-2
VMPAL-AP-10-QS1/4"-2
VMPAL-AP-10-QS4-2-T1
VMPAL-AP-10-QS6-2-T1
VMPAL-AP-10-QS5/32"-2-T1
VMPAL-AP-10-QS1/4"-2-T1
Duct 1 separated,
tubing O.D.
Single,
with electrical interlink­
ing module,
double solenoid
(for 2 solenoid coils),
with cartridge fitting
No duct separation,
tubing O.D.
Without electrical
interlinking module,
without cartridge fitting
–
–
560981
VMPAL-AP-4x10
With electrical interlink­
ing module,
single solenoid
(for 1 solenoid coil),
with cartridge fitting
No duct separation,
tubing O.D.
4 mm
561089
VMPAL-AP-4X10-QS4-1
6 mm
561083
VMPAL-AP-4X10-QS6-1
5/32"
561101
VMPAL-AP-4X10-QS5/32"-1
1/4"
561095
VMPAL-AP-4X10-QS1/4"-1
With electrical interlink­
ing module,
double solenoid
(for 2 solenoid coils),
with cartridge fitting
No duct separation,
tubing O.D.
4 mm
561090
VMPAL-AP-4X10-QS4-2
6 mm
561084
VMPAL-AP-4X10-QS6-2
5/32"
561102
VMPAL-AP-4X10-QS5/32"-2
1/4"
561096
VMPAL-AP-4X10-QS1/4"-2
For one sub-base
(1 valve position)
Grey – single solenoid
(1 solenoid coil)
Black – double solenoid
(2 solenoid coils)
Grey – single solenoid
(4 solenoid coils)
Black – double solenoid
(8 solenoid coils)
560961
VMPAL-EVAP-10-1
560962
VMPAL-EVAP-10-2
560967
VMPAL-EVAP-10-1-4
560968
VMPAL-EVAP-10-2-4
For combination of four
sub-bases
(4 valve positions)
Duct 1 separated,
tubing O.D.
è Internet: www.festo.com/catalog/...
53
Valve terminals MPA-L
Accessories
Ordering data
Code
Individual solenoid valve – Width 14 mm
5/2-way valve
Position function 1-32: M
Position function 1-32: MS
Position function 1-32: J
2x 3/2-way valve
Position function 1-32: N
Position function 1-32: NS
Valve function
Part No.
Type
Single solenoid
Single solenoid
Double solenoid
573718
573974
573717
VMPA14-M1H-M-PI
VMPA14-M1H-MS-PI
VMPA14-M1H-J-PI
573725
575977
VMPA14-M1H-N-PI
VMPA14-M1H-NS-PI
573724
575976
VMPA14-M1H-K-PI
VMPA14-M1H-KS-PI
573726
575979
VMPA14-M1H-H-PI
VMPA14-M1H-HS-PI
573719
573721
573720
VMPA14-M1H-B-PI
VMPA14-M1H-G-PI
VMPA14-M1H-E-PI
573723
573722
VMPA14-M1H-W-PI
VMPA14-M1H-X-PI
573727
575978
VMPA14-M1H-D-PI
VMPA14-M1H-DS-PI
573728
VMPA14-M1H-I-PI
573729
VMPA14-RP
Normally open
Normally open,
mechanical spring return
Position function 1-32: K Normally closed
Position function 1-32: KS Normally closed,
mechanical spring return
Position function 1-32: H 1x normally open – 1x normally closed
Position function 1-32: HS 1x normally open – 1x normally closed,
mechanical spring return
5/3-way valve
Position function 1-32: B Mid-position pressurised
Position function 1-32: G Mid-position closed
Position function 1-32: E
Mid-position exhausted
3/2-way valve
Position function 1-32: W Normally open, external compressed air supply
Position function 1-32: X Normally closed, external compressed air supply
2x 2/2-way valve
Position function 1-32: D Normally closed
Position function 1-32: DS Normally closed,
mechanical spring return
Position function 1-32: I
1x Normally closed,
1x Normally closed,
reversible
Vacant position – Width 14 mm
Position function 1-32: L
54
Blanking plate for one valve position in width 14 mm
A self-adhesive label is supplied
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Sub-base – Width 14 mm
Duct separation to the
right of sub-base 1-40: –
Duct separation to the
right of sub-base 1-40: T
Duct separation to the
right of sub-base 1-40: TR
Duct separation to the
right of sub-base 1-40: TS
–
Combination of four sub-bases – Width 14 mm
Combination manifold
block: Z
–
Valve function
Single,
without electrical
interlinking module,
without cartridge
fitting
Single,
with electrical inter­
linking module,
single solenoid
(for 1 solenoid coil),
with cartridge fitting
2015/03 – Subject to change
Type
No duct separation
–
560973
VMPAL-AP-14
Duct 1 separated
–
560975
VMPAL-AP-14-T1
Ducts 3, 5 separated
–
560977
VMPAL-AP-14-T35
Ducts 1 and 3,
5 separated
No duct separation,
tubing O.D.
–
560979
VMPAL-AP-14-T135
6 mm
8 mm
1/4"
5/16"
6 mm
8 mm
1/4"
5/16"
6 mm
8 mm
1/4"
5/16"
6 mm
8 mm
1/4"
5/16"
560995
560989
561007
561001
561019
561013
561031
561025
560996
560990
561008
561002
561020
561014
561032
561026
VMPAL-AP-14-QS6-1
VMPAL-AP-14-QS8-1
VMPAL-AP-14-QS1/4"-1
VMPAL-AP-14-QS5/16"-1
VMPAL-AP-14-QS6-1-T1
VMPAL-AP-14-QS8-1-T1
VMPAL-AP-14-QS1/4"-1-T1
VMPAL-AP-14-QS5/16"-1-T1
VMPAL-AP-14-QS6-2
VMPAL-AP-14-QS8-2
VMPAL-AP-14-QS1/4"-2
VMPAL-AP-14-QS5/16"-2
VMPAL-AP-14-QS6-2-T1
VMPAL-AP-14-QS8-2-T1
VMPAL-AP-14-QS1/4"-2-T1
VMPAL-AP-14-QS5/16"-2-T1
Duct 1 separated,
tubing O.D.
Single,
with electrical inter­
linking module,
double solenoid
(for 2 solenoid coils),
with cartridge fitting
No duct separation,
tubing O.D.
Without electrical
interlinking module,
without cartridge
fitting
–
–
560983
VMPAL-AP-4X14
With electrical
interlinking module,
single solenoid
(for 1 solenoid coil),
with cartridge fitting
No duct separation,
tubing O.D.
6 mm
561091
VMPAL-AP-4X14-QS6-1
8 mm
561085
VMPAL-AP-4X14-QS8-1
1/4"
561103
VMPAL-AP-4X14-QS1/4"-1
5/16"
561097
VMPAL-AP-4X14-QS5/16"-1
6 mm
561092
VMPAL-AP-4X14-QS6-2
8 mm
561086
VMPAL-AP-4X14-QS8-2
1/4"
561104
VMPAL-AP-4X14-QS1/4"-2
5/16"
561098
VMPAL-AP-4X14-QS5/16"-2
560963
VMPAL-EVAP-14-1
560964
VMPAL-EVAP-14-2
560969
VMPAL-EVAP-14-1-4
560970
VMPAL-EVAP-14-2-4
Duct 1 separated,
tubing O.D.
With electrical
No duct separation,
interlinking module, tubing O.D.
double solenoid
(for 2 solenoid coils),
with cartridge fitting
Electrical interlinking module – Width 14 mm
Type of module block
1-40: F
Type of module block
1-40: E
Type of module block
1-40: F
Type of module block
1-40: E
Part No.
For one sub-base
(1 valve position)
For combination of
four sub-bases
(4 valve positions)
Grey – single solenoid
(1 solenoid coil)
Black – double solenoid
(2 solenoid coils)
Grey – single solenoid
(4 solenoid coils)
Black – double solenoid
(8 solenoid coils)
è Internet: www.festo.com/catalog/...
55
Valve terminals MPA-L
Accessories
Ordering data
Code
Individual solenoid valve – Width 20 mm
5/2-way valve
Position function 1-32: M
Position function 1-32: MS
Position function 1-32: J
2x 3/2-way valve
Position function 1-32: N
Position function 1-32: NS
Position function 1-32: K
Position function 1-32: KS
Position function 1-32: H
Position function 1-32: HS
5/3-way valve
Position function 1-32: B
Position function 1-32: G
Position function 1-32: E
1x 3/2-way valve
Position function 1-32: W
Position function 1-32: X
2x 2/2-way valve
Position function 1-32: D
Position function 1-32: DS
Position function 1-32: I
Vacant position – Width 20 mm
Position function 1-32: L
56
Valve function
Part No.
Type
Single solenoid
Single solenoid, mechanical spring return
Double solenoid
8022034
571333
8022035
VMPA2-M1BH-M-PI
VMPA2-M1H-MS-PI
VMPA2-M1BH-J-PI
Normally open
Normally open,
mechanical spring return
Normally closed
Normally closed,
mechanical spring return
1x normally open – 1x normally closed
1x normally open – 1x normally closed,
mechanical spring return
537958
568655
VMPA2-M1H-N-PI
VMPA2-M1H-NS-PI
537957
568656
VMPA2-M1H-K-PI
VMPA2-M1H-KS-PI
537959
568658
VMPA2-M1H-H-PI
VMPA2-M1H-HS-PI
Mid-position pressurised
Mid-position closed
Mid-position exhausted
8022036
8022037
8022038
VMPA2-M1BH-B-PI
VMPA2-M1BH-G-PI
VMPA2-M1BH-E-PI
Normally open, external compressed air supply
Normally closed, external compressed air supply
8022040
8022039
VMPA2-M1BH-W-PI
VMPA2-M1BH-X-PI
Normally closed
Normally closed,
mechanical spring return
1x normally closed
1x normally closed, reversible
537960
568657
VMPA2-M1H-D-PI
VMPA2-M1H-DS-PI
543703
VMPA2-M1H-I-PI
Blanking plate for one valve position in width 20 mm
A self-adhesive label is supplied
537962
VMPA2-RP
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
-V- New
VMPA2-VSP
Valve terminals MPA-L
Accessories
Ordering data
Code
Vertical stacking modules – Width 20 mm
Pressure regulator 1-32: PA
Pressure regulator 1-32: PF
Pressure regulator 1-32: PC
Pressure regulator 1-32: PH
Pressure regulator 1-32: PB
Pressure regulator 1-32: PG
Pressure regulator 1-32: PL
Pressure regulator 1-32: PN
Pressure regulator 1-32: PK
Pressure regulator 1-32: PM
Pressure regulator 1-32: PV
Valve function
Part No.
Type
0.5 … 8.5 bar
0.5 … 5 bar
2 … 8.5 bar
2 … 5 bar
2 … 8.5 bar
2 … 5 bar
0.5 … 8.5 bar
0.5 … 5 bar
0.5 … 8.5 bar
0.5 … 5 bar
G1/8
543342
549055
543343
549056
543344
549057
543347
549113
543348
549114
8029486
VMPA2-B8-R1C2-C-10
VMPA2-B8-R1C2-C-06
VMPA2-B8-R2C2-C-10
VMPA2-B8-R2C2-C-06
VMPA2-B8-R3C2-C-10
VMPA2-B8-R3C2-C-06
VMPA2-B8-R6C2-C-10
VMPA2-B8-R6C2-C-06
VMPA2-B8-R7C2-C-10
VMPA2-B8-R7C2-C-06
VMPA2-VSP-0
6 mm
8 mm
10 mm
1/4"
5/16"
3/8"
0 … 16 bar
8035441
8029488
8029489
8035442
8029491
8029492
543487
VMPA2-VSP-QS6
VMPA2-VSP-QS8
VMPA2-VSP-QS10
VMPA2-VSP-QS1/4
VMPA2-VSP-QS5/16
VMPA2-VSP-QS3/8
PAGN-26-16-P10
0 … 10 bar
543488
PAGN-26-10-P10
0 … 1.0 MPa
563736
PAGN-26-1M-P10
0 … 1.6 MPa
563735
PAGN-26-1.6M-P10
Threaded adapter from 10 mm cartridge fitting connection
to thread G1/8
565811
QSP-10-G1/8
Pressure regulator
plate
(with 10 mm
cartridge fitting
connection for
pressure gauge)
For port 1
For port 2
For port 4
For port 2, reversible
For port 4, reversible
Vertical supply
plate
Connecting thread
With connector for
tubing O.D.
Pressure gauge 1-32: T
–
Pressure gauge 1-32: VF
2015/03 – Subject to change
Pressure gauge,
10 mm cartridge
fitting connection,
for pressure
regulator plate
Display unit bar/psi
Display unit MPa
è Internet: www.festo.com/catalog/...
-V-
-V-V-V-V-V-V-
57
Valve terminals MPA-L
Accessories
Ordering data
Code
Description
Sub-base – Width 20 mm
Duct separation to the
right of sub-base 1-40: –
Duct separation to the
right of sub-base 1-40: T
Duct separation to the
right of sub-base 1-40: TR
Duct separation to the
right of sub-base 1-40: TS
–
Electrical interlinking module – Width 20 mm
Type of module block
1-40: D
Type of module block
1-40: B
58
Single,
No duct separation
without electrical
interlinking module,
Duct 1 separated
without cartridge fitting
Ducts 3, 5 separated
Single,
with electrical inter­
linking module,
single solenoid
(for 1 solenoid coil),
with cartridge fitting
Ducts 1 and 3,
5 separated
No duct separation,
tubing O.D.
Duct 1 separated,
tubing O.D.
Part No.
Type
–
560974
VMPAL-AP-20
–
560976
VMPAL-AP-20-T1
–
560978
VMPAL-AP-20-T35
–
560980
VMPAL-AP-20-T135
8 mm
10 mm
5/16"
3/8"
8 mm
10 mm
5/16"
3/8"
8 mm
10 mm
5/16"
3/8"
8 mm
10 mm
5/16"
3/8"
560997
560991
561009
561003
561021
561015
561033
561027
560998
560992
561010
561004
561022
561016
561034
561028
VMPAL-AP-20-QS8-1
VMPAL-AP-20-QS10-1
VMPAL-AP-20-QS5/16"-1
VMPAL-AP-20-QS3/8"-1
VMPAL-AP-20-QS8-1-T1
VMPAL-AP-20-QS10-1-T1
VMPAL-AP-20-QS5/16"-1-T1
VMPAL-AP-20-QS3/8"-1-T1
VMPAL-AP-20-QS8-2
VMPAL-AP-20-QS10-2
VMPAL-AP-20-QS5/16"-2
VMPAL-AP-20-QS3/8"-2
VMPAL-AP-20-QS8-2-T1
VMPAL-AP-20-QS10-2-T1
VMPAL-AP-20-QS5/16"-2-T1
VMPAL-AP-20-QS3/8"-2-T1
560965
VMPAL-EVAP-20-1
560966
VMPAL-EVAP-20-2
Single,
with electrical inter­
linking module,
double solenoid
(for 2 solenoid coils),
with cartridge fitting
No duct separation,
tubing O.D.
For one sub-base
(1 valve position)
Grey – single solenoid
(1 solenoid coil)
Black – double solenoid
(2 solenoid coils)
Duct 1 separated,
tubing O.D.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Description
Tie rod: –
Threaded rod for tie rod, width across flats
5 mm
The threaded rod/sleeve combination is
selected based on the number and width of
the individual sub-bases.
–
Sleeve, internal hex 4 mm
–
Tie rod extender for subsequently extend­
ing the valve terminal by a sub-base in
width
Tie rod extender for subsequently extend­
ing the valve terminal by a supply module
Tie rod extender for subsequently extend­
ing the valve terminal by four sub-bases in
width
Screw M4 with internal hex 2.5 mm,
for tie rod
Part No.
Type
PU1)
5 mm
45 mm
85 mm
125 mm
165 mm
205 mm
245 mm
285 mm
325 mm
365 mm
405 mm
445 mm
485 mm
525 mm
565 mm
605 mm
645 mm
685 mm
725 mm
765 mm
805 mm
36 mm
46 mm
56 mm
66 mm
10 mm
14 mm
20 mm
20 mm
561116
561117
561118
561119
561120
561121
561122
561123
561124
561125
561126
561127
561128
561129
561130
561131
561132
561133
561134
561175
561176
561135
561136
561137
561138
561139
561140
561141
561141
VMPAL-ZAS-5
VMPAL-ZAS-45
VMPAL-ZAS-85
VMPAL-ZAS-125
VMPAL-ZAS-165
VMPAL-ZAS-205
VMPAL-ZAS-245
VMPAL-ZAS-285
VMPAL-ZAS-325
VMPAL-ZAS-365
VMPAL-ZAS-405
VMPAL-ZAS-445
VMPAL-ZAS-485
VMPAL-ZAS-525
VMPAL-ZAS-565
VMPAL-ZAS-605
VMPAL-ZAS-645
VMPAL-ZAS-685
VMPAL-ZAS-725
VMPAL-ZAS-765
VMPAL-ZAS-805
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAE-10
VMPAL-ZAE-14
VMPAL-ZAE-20
VMPAL-ZAE-20
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
10 mm
570779
VMPAL-ZAE-10-4
3
14 mm
570780
VMPAL-ZAE-14-4
3
30 mm
571924
VMPAL-M4X30
3
39 mm
561142
VMPAL-MS-4x10
10
Tie rod
–
Screw
–
1)
Screw M3 and square nut, for linking four
sub-bases
Packaging unit quantity.
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
59
-V- New
VAMC
Valve terminals MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
PU1)
–
Mounting bracket
Wall brackets should be mounted max. every 13 cm on
the valve terminal
560949
VMPAL-BD
10
Mounting accessories: H MPA-L with multi-pin plug connection
526032
CPX-CPA-BG-NRH
3
Mounting accessories: H MPA-L with fieldbus connection
560798
VMPAF-FB-BG-NRH
2
–
For releasing the electrical interlinking module from the
sub-base
572017
VMPAL-LW
1
Manual override: N
Cover cap for manual override, non-detenting
540897
VMPA-HBT-B
10
Manual override: V
Cover cap for manual override, covered
540898
VMPA-HBV-B
10
Manual override: Y
Cover cap for manual override, without accessories
detenting
8002234 VAMC-L1-CD
-V- 10
Holder for inscription label
IBS-6x10
Width 10 mm
561109
VMPAL-ST-AP-10
10
Width 14 mm
561112
VMPAL-ST-AP-14
10
Width 20 mm
561115
VMPAL-ST-AP-20
10
18576
IBS-6X10
64
Mounting
H-rail mounting
Releasing tool
Cover cap
Inscription label holder/inscription labels
Inscription label holder
for sub-bases: TM
–
1)
60
Inscription label, 6x10 mm
Packaging unit quantity.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
Type of module block
1-40: U
With electrical interlinking module, without cartridge fitting
560950
VMPAL-SP-0
Type of module block
1-40: U
With electrical interlinking module,
with cartridge fitting for tubing O.D.
8 mm
10 mm
12 mm
5/16"
3/8"
1/2"
Without electrical interlinking module, without cartridge fitting
573645
560951
560952
573646
560953
560954
570774
VMPAL-SP-QS8
VMPAL-SP-QS10
VMPAL-SP-QS12
VMPAL-SP-QS5/16"
VMPAL-SP-QS3/8"
VMPAL-SP-QS1/2"
VMPAL-SP
Exhaust port:
UD, UE, UF, UM, UN, UP
or UG
Exhaust plate for ducted exhaust air
560956
VMPAL-EG
Exhaust port:
UE
Exhaust port:
UN
Exhaust port: –
Exhaust plate for ducted exhaust air, with cartridge fitting for
tubing O.D. 10 mm
Exhaust plate for ducted exhaust air, with cartridge fitting for
tubing O.D. 3/8"
Flat plate silencer
560957
VMPAL-EG-QS10
560959
VMPAL-EG-QS3/8"
560955
VMPAL-EU
Black
for supply module (signals are passed through)
571011
VMPAL-EVAP-20-SP
Supply module
Type of module block
1-40: U
Plate
Electrical interlinking module
Type of module block
1-40: U
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
61
Valve terminals MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
Right-hand end plate: –
Low,
with ports 12/14, 82/84,
with pilot air selector for choosing the pilot air supply
(internal or external)
560945
VMPAL-EPR
Right-hand end plate: D
High,
with ports 1, 3, 5, 12/14, 82/84,
with pilot air selector for choosing the pilot air supply
(internal or external), reverse operation possible
560947
VMPAL-EPR-SP
Sub-D, 9-pin,
8 addresses
Sub-D, 25-pin,
24 addresses
Sub-D, 44-pin,
32 addresses
Flat cable, 40-pin,
32 addresses
Terminal strip, 33-pin,
32 addresses
Sub-D, 25-pin,
24 addresses
Sub-D, 44-pin,
32 addresses
32 addresses
570777
VMPAL-EPL-SD9-IP40
560940
VMPAL-EPL-SD25-IP40
560941
VMPAL-EPL-SD44-IP40
560942
VMPAL-EPL-FL40-IP40
560943
VMPAL-EPL-KL33-IP40
560938
VMPAL-EPL-SD25
560939
VMPAL-EPL-SD44
570783
VMPAL-EPL-CPX
32 addresses
575667
VMPAL-EPL-IPO32
Right-hand end plate
Left-hand end plate
Electrical connection:
Electrical interface for multi-pin
MS2
plug connection, IP40
Electrical connection:
MS1
Electrical connection:
MS3
Electrical connection: MF1
Electrical connection: MC
1)
62
Electrical connection:
MS6
Electrical connection:
MS8
Electrical connection: CX
Electrical interface for multi-pin
plug connection
Electrical connection: LK
Node with IO-Link
Electrical connection: PT
Node with I-Port interface
Pneumatic interface for CPX
terminal
A self-adhesive label is supplied.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
2.5 m
5m
10 m
2.5 m
5m
10 m
2.5 m
5m
10 m
2.5 m
5m
10 m
2.5 m
5m
10 m
0.5 … 30 m
2.5 m
5m
10 m
0.5 … 30 m
2.5 m
5m
10 m
0.5 … 30 m
2.5 m
5m
10 m
0.5 … 30 m
2.5 m
5m
10 m
0.5 … 30 m
2.5 m
5m
10 m
0.5 … 30 m
531184
531185
531186
530049
530050
530051
530046
530047
530048
575113
575114
575115
560416
560417
560418
562389
560410
560411
560412
562391
560422
560423
560424
562390
560419
560420
560421
562392
560413
560414
560415
562394
560425
560426
560427
562393
KMP6-09P-08-2,5
KMP6-09P-08-5
KMP6-09P-08-10
KMP6-25P-12-2,5
KMP6-25P-12-5
KMP6-25P-12-10
KMP6-25P-20-2,5
KMP6-25P-20-5
KMP6-25P-20-10
NEBV-S1G44-K-2.5-N-LE44-S6
NEBV-S1G44-K-5-N-LE44-S6
NEBV-S1G44-K-10-N-LE44-S6
VMPAL-KM-V-SD25-IP67-2,5
VMPAL-KM-V-SD25-IP67-5
VMPAL-KM-V-SD25-IP67-10
VMPAL-KM-V-SD25-IP67-X
VMPAL-KMSK-V-SD25-IP67-2,5
VMPAL-KMSK-V-SD25-IP67-5
VMPAL-KMSK-V-SD25-IP67-10
VMPAL-KMSK-V-SD25-IP67-X
VMPAL-KM-V-SD44-IP67-2,5
VMPAL-KM-V-SD44-IP67-5
VMPAL-KM-V-SD44-IP67-10
VMPAL-KM-V-SD44-IP67-X
VMPAL-KM-S-SD25-IP67-2,5
VMPAL-KM-S-SD25-IP67-5
VMPAL-KM-S-SD25-IP67-10
VMPAL-KM-S-SD25-IP67-X
VMPAL-KMSK-S-SD25-IP67-2,5
VMPAL-KMSK-S-SD25-IP67-5
VMPAL-KMSK-S-SD25-IP67-10
VMPAL-KMSK-S-SD25-IP67-X
VMPAL-KM-S-SD44-IP67-2,5
VMPAL-KM-S-SD44-IP67-5
VMPAL-KM-S-SD44-IP67-10
VMPAL-KM-S-SD44-IP67-X
25-pin
–
560428
VMPAL-KM-SD25-IP67-0
44-pin
–
560429
VMPAL-KM-SD44-IP67-0
570895
NECU-FCG40-K
Connecting cable for multi-pin plug connection with Sub-D plug socket
Connecting cable: DA
Socket 9-pin, Sub-D, open cable end 9-pin
Connecting cable: DB
Connecting cable: DC
–
Socket 25-pin, Sub-D, open cable end 15-pin
–
–
Connecting cable: DD
Socket 25-pin, Sub-D, open cable end 25-pin
Connecting cable: DK
Connecting cable: DF
Connecting cable: DG
Socket 44-pin, Sub-D, open cable end 44-pin
Connecting cable: DH
Connecting cable: DJ
Connecting cable: CA
Cable outlet to front
25-pin
(only with left-hand end plate MS6)
Connecting cable: CB
Connecting cable: CC
–
Connecting cable: CQ
Cable outlet to front
25-pin
(only with left-hand end plate MS6),
Connecting cable: CR
suitable for use with energy chains
Connecting cable: CS
–
Connecting cable: CJ
Cable outlet to front
44-pin
(only with left-hand end plate MS8)
Connecting cable: CK
Connecting cable: CL
–
Connecting cable: CD
Cable outlet to side
25-pin
(only with left-hand end plate MS6)
Connecting cable: CE
Connecting cable: CH
–
Connecting cable: CT
Cable outlet to side
25-pin
(only with left-hand end plate MS6),
Connecting cable: CU
suitable for use with energy chains
Connecting cable: CV
–
Connecting cable: CM
Cable outlet to side
44-pin
(only with left-hand end plate MS8)
Connecting cable: CN
Connecting cable: CP
–
Cover for multi-pin plug connection without connecting cable with Sub-D plug socket
Electrical multi-pin plug Cable outlet to side or front
cover: EZ
(only with left-hand end plate MS6)
Electrical multi-pin plug Outlet either to the side or front
cover: EY
(only with left-hand end plate MS8)
Plug connector
–
2015/03 – Subject to change
Pre-assembled plug connector for flat cable, 40-pin, for flat
cable cross section 0.08 … 0.13 mm2
è Internet: www.festo.com/catalog/...
63
Valve terminals MPA-L
Accessories
Ordering data
Code
Cartridge fitting for sub-base in width 10 mm
Standard
AA
connection for valve AB
size 10 mm:
–
AJ
AQ
AK
AL
–
–
–
–
–
64
10 mm cartridge fitting, nickel-plated brass,
for working lines,
connection for tubing O.D.
10 mm cartridge fitting, plastic,
L-shape, for working lines,
connection for tubing O.D.
14 mm cartridge fitting, plastic,
for working lines,
connection for tubing O.D.
14 mm cartridge fitting, plastic,
L-shape, for working lines,
connection for tubing O.D.
14 mm cartridge fitting, plastic,
long L-shape, for working lines,
connection for tubing O.D.
Cartridge fitting for sub-base in width 20 mm
Standard
CD
connection for valve –
size 20 mm:
CQ
CT
–
1)
10 mm cartridge fitting, plastic,
for working lines,
connection for tubing O.D.
10 mm cartridge fitting, plastic,
long L-shape, for working lines,
connection for tubing O.D.
Cartridge fitting for sub-base in width 14 mm
Standard
BC
connection for valve –
size 14 mm:
BL
BQ
–
–
Part No.
Type
PU1)
3 mm
4 mm
6 mm
1/8"
5/32"
3/16"
1/4"
4 mm
132621
132622
132623
132852
132624
132625
132626
172972
QSPKG10-3
QSPKG10-4
QSPKG10-6
QSPKG10-1/8-U
QSPKG10-5/32-U
QSPKG10-3/16-U
QSPKG10-1/4-U
QSP10-4
10
10
10
10
10
10
10
10
6 mm
172973
QSP10-6
10
3 mm
4 mm
6 mm
1/8"
5/32"
3/16"
1/4"
3 mm
4 mm
6 mm
1/8"
5/32"
3/16"
1/4"
132853
132920
132921
132854
132922
132923
132924
132861
132925
132926
132862
132927
132928
132929
QSPLKG10-3
QSPLKG10-4
QSPLKG10-6
QSPLKG10-1/8-U
QSPLKG10-5/32-U
QSPLKG10-3/16-U
QSPLKG10-1/4-U
QSPLLKG10-3
QSPLLKG10-4
QSPLLKG10-6
QSPLLKG10-1/8-U
QSPLLKG10-5/32-U
QSPLLKG10-3/16-U
QSPLLKG10-1/4-U
10
10
10
10
10
10
10
10
10
10
10
10
10
10
6 mm
8 mm
1/4"
5/16"
6 mm
8 mm
1/4"
5/16"
6 mm
132930
132931
132932
132933
132938
132939
132940
132941
132942
QSPKG14-6
QSPKG14-8
QSPKG14-1/4-U
QSPKG14-5/16-U
QSPLKG14-6
QSPLKG14-8
QSPLKG14-1/4-U
QSPLKG14-5/16-U
QSPLLKG14-6
10
10
10
10
10
10
10
10
10
8 mm
132943
QSPLLKG14-8
10
1/4"
132944
QSPLLKG14-1/4-U
10
5/16"
132945
QSPLLKG14-5/16-U
10
8 mm
10 mm
5/16"
3/8"
8 mm
10 mm
5/16"
3/8"
8 mm
132649
132650
132651
132652
132946
132947
132948
132949
132950
QSPKG18-8
QSPKG18-10
QSPKG18-5/16-U
QSPKG18-3/8-U
QSPLKG18-8
QSPLKG18-10
QSPLKG18-5/16-U
QSPLKG18-3/8-U
QSPLLKG18-8
10
10
10
10
10
10
10
10
10
10 mm
132951
QSPLLKG18-10
10
5/16"
132952
QSPLLKG18-5/16-U
10
3/8"
132953
QSPLLKG18-3/8-U
10
Description
18 mm cartridge fitting, plastic,
for working lines,
connection for tubing O.D.
18 mm cartridge fitting, plastic,
L-shape, for working lines,
connection for tubing O.D.
18 mm cartridge fitting, plastic,
long L-shape, for working lines,
connection for tubing O.D.
Packaging unit.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Cartridge fitting for supply module
–
Part No.
Type
PU1)
8 mm
10 mm
12 mm
5/16"
3/8"
1/2"
8 mm
10 mm
12 mm
5/16"
3/8"
1/2"
8 mm
132633
132634
132635
132636
132637
132638
132855
132856
132857
132858
132859
132860
132863
QSPKG20-8
QSPKG20-10
QSPKG20-12
QSPKG20-5/16-U
QSPKG20-3/8-U
QSPKG20-1/2-U
QSPLKG20-8
QSPLKG20-10
QSPLKG20-12
QSPLKG20-5/16-U
QSPLKG20-3/8-U
QSPLKG20-1/2-U
QSPLLKG20-8
10
10
10
10
10
10
10
10
10
10
10
10
10
10 mm
132864
QSPLLKG20-10
10
12 mm
132865
QSPLLKG20-12
10
5/16"
132866
QSPLLKG20-5/16-U
10
3/8"
132867
QSPLLKG20-3/8-U
10
1/2"
132868
QSPLLKG20-1/2-U
10
Adapter from 10 mm cartridge fitting connection to thread M7
572380
VMPAL-F10-M7
10
Adapter from 14 mm cartridge fitting connection to thread G1/8
574084
VMPAL-F14-G1/8
10
Adapter from 18 mm cartridge fitting connection to thread G1/4
573914
VMPAL-F20-G1/4
10
Adapter from 20 mm cartridge fitting connection to thread G1/4 572381
VMPAL-FSP-G1/4
10
Description
20 mm cartridge fitting, plastic,
for supply ports,
connection for tubing O.D.
–
20 mm cartridge fitting, plastic,
L-shape, for supply ports,
connection for tubing O.D.
–
20 mm cartridge fitting, plastic,
long L-shape, for supply ports,
connection for tubing O.D.
Adapter for sub-bases
Standard connection for
valve size 10 mm: AGG
Standard connection for
valve size 14 mm: BGG
Standard connection for
valve size 20 mm: CGG
Adapter for supply module/plate
–
1)
Packaging unit.
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
65
Valve terminals MPA-L
Accessories
Ordering data
Part No.
Type
PU1)
4 mm
6 mm
6 mm
153319
153321
186108
QSM-M7-4-I
QSM-M7-6-I
QS-G1/4-6-I
10
10
10
6 mm
8 mm
10 mm
6 mm
8 mm
10 mm
12 mm
8 mm
186097
186099
186101
193411
193412
193413
533848
533930
QS-G1/4-6
QS-G1/4-8
QS-G1/4-10
QS-F-G1/4-6
QS-F-G1/4-8
QS-F-G1/4-10
QS-F-G1/4-12
QS-F-G1/4-8-I
10
10
10
10
10
10
10
10
10 mm
533931
QS-F-G1/4-10-I
10
6 mm
8 mm
10 mm
12 mm
6 mm
8 mm
10 mm
533881
533882
533883
533884
186316
186317
186318
QS-F-G1/4-6H
QS-F-G1/4-8H
QS-F-G1/4-10H
QS-F-G1/4-12H
QS-VO-G1/4-6
QS-VO-G1/4-8
QS-VO-G1/4-10
10
10
10
10
10
10
10
6 mm
153057
QSL-6H
10
8 mm
153058
QSL-8H
10
Long push-in sleeve 
6 mm
153066
QSL-6HL
10
Push-in fitting with sealing ring,
connecting thread M7,
with external hex, for tubing O.D.
4 mm
Long push-in fitting with sealing ring,
connecting thread M7,
with external hex, for tubing O.D.
Push-in fitting with sealing ring,
connecting thread G1/4,
with external hex, for tubing O.D.
Push-in fitting, metal, with sealing ring,
connecting thread G1/4,
with external hex, for tubing O.D.
4 mm
186352
130773
186353
130774
186354
QSML-M7-4
QSML-M7-4-100
QSML-M7-6
QSML-M7-6-100
QSMLL-M7-4
10
100
10
100
10
6 mm
186355
QSMLL-M7-6
10
6 mm
8 mm
10 mm
6 mm
8 mm
10 mm
12 mm
6 mm
8 mm
10 mm
12 mm
6 mm
186118
186120
186122
193421
193422
193423
533853
556846
556847
556848
556849
186149
QSL-G1/4-6
QSL-G1/4-8
QSL-G1/4-10
QSL-F-G1/4-6
QSL-F-G1/4-8
QSL-F-G1/4-10
QSL-F-G1/4-12
QSLL-F-G1/4-6
QSLL-F-G1/4-8
QSLL-F-G1/4-10
QSLL-F-G1/4-12
QSLV-G1/4-6-I
10
10
10
10
10
10
10
10
10
10
10
10
8 mm
186151
QSLV-G1/4-8-I
10
Code
Description
–
Connecting thread M7 with sealing ring,
with internal hex, for tubing O.D.
Connecting thread G1/4 with sealing ring,
with internal hex, for tubing O.D.
Connecting thread G1/4 with sealing ring,
with external hex, for tubing O.D.
Push-in fitting
–
–
Connecting thread G1/4, metal,
with external hex, for tubing O.D.
–
Connecting thread G1/4, metal,
with internal hex, for tubing O.D.
–
Connecting thread G1/4, metal,
with push-in sleeve 
–
Connecting thread G1/4, with external hex,
flame-retardant, for tubing O.D.
–
Push-in sleeve 
Push-in L-connector
–
–
–
Long push-in fitting, metal,
connecting thread G1/4,
with external hex, for tubing O.D.
–
1)
66
Push-in fitting,
connecting thread G1/4,
with internal hex, for tubing O.D.
6 mm
Packaging unit.
è Internet: www.festo.com/catalog/...
Subject to change – 2015/03
Valve terminals MPA-L
Accessories
Ordering data
Code
Push-in fitting, self-sealing
–
Description
Part No.
Type
PU1)
With sealing ring, with external hex,
connecting thread G1/4,
for tubing O.D.
With sealing ring, with external hex, L shape,
connecting thread G1/4,
for tubing O.D.
6 mm
8 mm
10 mm
6 mm
8 mm
10 mm
186296
186298
186300
186306
186308
186310
QSK-G1/4-6
QSK-G1/4-8
QSK-G1/4-10
QSKL-G1/4-6
QSKL-G1/4-8
QSKL-G1/4-10
1
1
1
1
1
1
With external hex,
connecting thread G1/4,
for tubing O.D.
With external hex, L-shape,
connecting thread G1/4,
for tubing O.D.
6 mm
186278
QSR-G1/4-6
1
8 mm
186280
QSR-G1/4-8
1
6 mm
186287
QSRL-G1/4-6
1
8 mm
186289
QSRL-G1/4-8
1
Connecting thread
M7
161418
534218
165004
534220
UC-M7
UC-M7-50
UC-1/4
UC-1/4-20
1
50
1
20
174309
3570
172976
172987
172996
B-M7
B-3/8
QSP10-PTB
QSP14-PTB
QSP17-PTB
10
10
1
1
1
556353
556354
556356
556355
556357
556358
P.BE-MPAL-DE
P.BE-MPAL-EN
P.BE-MPAL-FR
P.BE-MPAL-ES
P.BE-MPAL-IT
P.BE-MPAL-SV
Rotary push-in fitting
–
Silencer
–
G1/4
Blanking plug
–
Thread
M7
G3/8
10 mm
14 mm
18 mm
Cartridge fitting
Manual
Documentation: DE
Documentation: EN
Documentation: FR
Documentation: ES
Documentation: IT
Documentation: SV
1)
MPA-L Pneumatic Components
German
English
French
Spanish
Italian
Swedish
Packaging unit.
2015/03 – Subject to change
è Internet: www.festo.com/catalog/...
67
Product Range and Company Overview
A Complete Suite and Company Overview
Our experienced engineers provide complete support at every stage of your development process, including: conceptualization,
analysis, engineering, design, assembly, documentation, validation, and production
Custom Automation Components
Complete custom engineered solutions
Custom Control Cabinets
Comprehensive engineering support
and on-site services
Complete Systems
Shipment, stocking and storage services
The Broadest Range of Automation Components
With a comprehensive line of more than 30,000 automation components, Festo is capable of solving the most complex
automation requirements
Electromechanical
Electromechanical actuators, motors,
controllers & drivers
Pneumatics
Pneumatic linear and rotary actuators,
valves, and air supply
P/Cs and ,O 'evices
PLC’s, operator interfaces, sensors
and I/O devices
To meet this commitment, we strive to ensure a consistent, integrated, and systematic approach to
management that will meet or exceed the requirements of the ISO 9001 standard for Quality
0anagement and the ISO 1001 standard for (nvironmental 0anagement
ISO 9001
ISO 14001
&HUWLÀHG
Company
&(57&$$4(617*$
4ualit\ Assurance ,SO and ,SO Certiącations
Festo Corporation is committed to supply all Festo products and services that will meet or exceed
our customersn reTuirements in product Tuality, delivery, customer service and satisfaction
&(57&$4(617*$
Supporting Advanced Automation… As No One Else Can!
Festo is a leading global manufacturer of pneumatic and electromechanical systems, components and controls for industrial
automation, Zith more than , employees in national headTuarters serYing more than countries For more than years,
Festo has continuously elevated the state of manufacturing with innovations and optimized motion control solutions that deliver higher
performing, more proątable automated manufacturing and processing eTuipment 2ur dedication to the advancement of automation
extends beyond technology to the education and development of current and future automation and robotics designers with simulation
tools, teaching programs, and onsite services
 Copyright 01, Festo Corporation :hile every effort is made to ensure that all dimensions and speciącations are correct, Festo cannot guarantee that publications are
completely free of any error, in particular typing or printing errors $ccordingly, Festo cannot be held responsible for the same For /iability and :arranty conditions, refer to our
oTerms and Conditions of Salep, available from your local Festo ofące $ll rights reserved 1o part of this publication may be reproduced, distributed, or transmitted in any form
or by any means, electronic, mechanical, photocopying or otherwise, without the prior written permission of Festo $ll technical data subMect to change according to technical
update
Printed on recycled paper at 1ew +orizon *raphic, Inc, FSC certiąed as an environmental friendly printing plant
Festo North America
1 Festo Canada
Headquarters
Festo Inc.
5300 Explorer Drive
0ississauga, O1
LW 5*
2 Montréal
5600, Trans-Canada
Pointe-Claire, QC
+95 1%6
3 Québec City
930, rue Watt11
Québec, QC
*1; *3
4 Festo United States
Headquarters
Festo Corporation
395 Moreland Road
+auppauge, 1<
11
5 Appleton
1orth 9 Tower 9iew Drive, Suite 1
Greenville, WI
59
7 'etroit
11 West Long Lake Road
Troy, MI
09
6 Chicago
5 W Algonquin - Suite 30
Arlington +eights, IL
60005
8 Silicon Valley
935 Southfront Road, Suite F
Livermore, CA
9550
Canadian Customers
Commercial Support:
Tel: 1 *O FESTO 1 3 3
Fax: 1 F; FESTO 1 393 3
Email: festocanada#cafestocom
Technical Support:
Tel:1 *O FESTO 1 3 3
Fax:1 F; FESTO1 393 3
Email: technicalsupport#cafestocom
USA Customers
Commercial Support:
Tel:1 00 99 FESTO 1 00 993 3
Fax:1 00 9 FESTO 1 00 93 3
Email: customerservice#usfestocom
Technical Support:
Tel:1 *O FESTO 1 3 3
Fax:100 9 FESTO1 00 93 3
Email: productsupport#usfestocom
SubMect to change
Internet: www.festo.com/us
C
Festo Regional Contact Center

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement