Bosch PPH6 C8 Series Specifications

CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • INTAKE
The R&D High Performance Power Plenum Air
Filter Kit was designed, developed and dyno
tested exclusively for the new Yamaha SHO/FZR
supercharged intake system to unleash low-end,
mid-range, and peak horsepower trapped in the
restrictive stock air box. The exclusive lightweight filter
design couples to the OEM supercharger hose and is
engineered with a large 6”x10”x6” plenum to deliver
massive cubic air volume and improved air speed to the
supercharger. Replacing the O.E.M. air box with the R&D Filter kit offers an
economical way to improve performance.
Description
R&D FX-SHO/FZR/FZS
Performance Power Plenum Air Filter Kit
Part No.
200-01801
R&D VXR/VXS POWER
PLENUM FILTER KIT
The R&D High Performance Power Plenum Air
Filter Kit was designed and developed exclusively
for the new Yamaha 1.8 liter N/A engine. The R&D
filter kit will unleash low-end, mid-range, and peak
horsepower trapped in the restrictive stock air box.
The exclusive lightweight filter design couples to
the OEM throttle body through a tuned built in
velocity stack. The engineered oversized Tear
Drop plenum, delivers the velocity and cubic air volume needed to add
power. Power Plenum Filters generate the maximum airflow and volume.
Description
R&D VXR/VXS Power Plenum Filter Kit
Part No.
200-01805
R&D FX-SHO/FZR/FZS POWER
PLENUM FLAME ARRESTER
FOR STOCK AIR BOX
The R&D High Flow Filter design replaces the restrictive stock filter inside the
stock air box, allowing improved air flow. Why? Because more air flow means
more power and improved performance. The washable and reusable design
means this will be the last filter you will ever have to buy.
Description
R&D FX-SHO/FZR/FZS/VXR/VXS
Power Plenum Flame Arrester
Part No.
200-01800
R&D COLD AIR INLET KIT
The R&D Cold Air Adaptor Kit is a simple kit that
allows the front hatch cowling to be modified by
simply boring a hole in the cowling insert (located
on the bottom side of the hatch cover) and
installing the R&D molded plastic hose flange adaptor with kit supplied pop
rivets. The R&D Flange allows one of the existing air intake hoses to be
connected to the flange. The result is an inexpensive way to ventilate the
engine compartment with cool outside air. The Cold Air Adaptor kit will
improve airflow to the engine allowing power and RPM gains.
Description
R&D Cold Air Inlet Kit
30
R&D FX-SHO/FZR/FZS
PRO COMP COOL
AIR FILTER KIT
R&D PERFORMANCE POWER
PLENUM AIR FILTER KIT
©2012 Hot Products. All rights reserved.
Part No.
200-01806
The system is designed and tested with
boost levels above 23 pounds and speeds
of 92+ MPH. The R&D System utilizes an
oversized specifically designed 7.25” x 5.5”
x 6” teardrop shaped R&D Power Plenum
Filter w/crankcase vent that rubber mounts
in the space over the top left side of the
gas tank. The system ducts its air supply to
the supercharger via an “Indy Car style”
3.5” mandrel bent Aluminum tube and
couples to the supercharger with a 90°
Nomex tapered reduction elbow. Power Plenum Filters generate the maximum
airflow and volume and install in minutes. Recommended for the R&D C1, C3,
C5, C20X and C23X Monster Supercharger Wheel kits and Superchargers.
This system will also couple to the soon to be released R&D Cool Charger
Housing, a 100% water-cooled supercharger Housing.
Description
Part No.
R&D FX-SHO/FZR/FZS Pro Comp Cool Air Filter Kit 200-01802
FOR INTAKE
MANIFOLD
OEM
R&D
FOR INTERCOOLER
R&D FX-SHO POWER CORE INTAKE
MANIFOLD/INTERCOOLER CFM KIT
The R&D FX-SHO/FZR/FZS Power Intake Manifold and Intercooler CFM
Kit was developed to increase airflow into and through the intake system
by relieving restrictions. The R&D FX-SHO/FZR/FZS intake manifold ribbon
remover sleeve will unlock a 40 CFM (cubic feet per minute) air flow
restriction by replacing the intake manifold ribbon with the R&D billet venturi
sleeve. The R&D Intercooler Spacer will unlock a 30-35 CFM restriction in
the intercooler. The R&D FX-SHO/FZR/FZS Intake Kit will add low end and
mid range throttle response, and a full 100 plus rpms to top end performance
to a stock FX-SHO/FZR/FZS. The R&D FX-SHO/FZR/FZS Intake Kit is
an absolute must have parts kit to remove intake restrictions before
contemplating power adding compressor booster wheels or turbo charger
kits to the FX-SHO/FZR/FZS engine. True horsepower gains on the
ßFX-SHO/FZR/FZS start right here with the R&D Intake Kit. More airflow will
equal more power, and there is no other way around the fact that restricted
is restricted power.
Description
R&D FX-SHO/FZR/FZS Power Core Billet Intake
Manifold Sleeve & Intercooler Spacer CFM Kit
R&D FX-SHO/FZR/FZS Power Core
Intake Manifold Sleeve Only
R&D FX-SHO/FZR/FZS Intercooler CFM Spacer Only
R&D VXR/VXS Power Sleeve Intake Manifold
Upgrade Kit
Part No.
612-18000
612-17998
612-17999
232-18000
YAMAHA FX-SHO/FZ/VXR/VXS • INTAKE
YAMAHA
4 STROKE
INATKE
SYSTEMS
RIVA VXR/VXS POWER FILTER KIT
The RIVA Power Filter feeds your FX-SHO, FZS or FZR a steady diet of cool
air delivering greatly improved acceleration and rpm. Replaces restrictive stock
air box with a high-volume, precision-formed intake duct that attaches to
the supercharger via a large 4” adapter. Cool air enters the system via an
oversized K&N filter element. Includes water-repellent pre-filter.
Description
Part No.
RIVA FX-SHO/FZR/FZS Performance Power Filter Kit RY13040
Power Filter Only (for RY13040)
RK13090-2
Part No.
RY13060
RK13090-2
EXHAUST
Description
RIVA VXR/VXS Power Filter Kit
Power Filter Only (for RY13060)
RIVA PERFORMANCE YAMAHA
FX-SHO/FZR/FZS POWER FILTER KIT
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Key Features:
• Delivers increased acceleration & top speed.
• True "cold air" system utilizes OEM hood scoop.
• Ultra-dry water trap keeps water out of system.
• Genuine screen type K&N Flame Arrestor & water repellent prefilter cover.
• Large 4" smooth-bore ducting attaches to engine via flow-matched
velocity stack.
• Includes updated crankcase breather system for improved performance.
ENGINE/
GASKETS
RIVA’s VXR/VXS Power Filter is a true "cold air" intake system that draws cool
air from outside your engine compartment delivering significant performance
gains. Utilizes OEM hood scoop to feed air into an ultra-dry water trap system
for reliable operation in rough water conditions. Cold air is delivered to engine
via large 4" smooth-bore ducting that is secured to throttle body with unique
velocity stack and sturdy billet clamps. Kit also includes an improved breather
system that keeps hot oil vapor and crankcase fumes from entering your
engine's air intake. Requires use of Engine Breather Uptake Kit
(RY14040-EBUK-1)
BODY
RIVA’s Intake Manifold Upgrade Kit enables your 1.8L naturally aspirated
engine to produce more horsepower by delivering increased air flow.
Precision tapered billet sleeve directly replaces restrictive mesh element
in the intake manifold. Provides improved low end punch and mid range pull
through a quick & easy installation. Includes detailed installation instructions.
NOTE: Testing has determined the stock ECU will compensate for the
increased air flow provided by the Intake Manifold Upgrade Kit. Requires
RIVA Power Filter Kit to meet U.S. Coast Guard certified flame arrestor
requirements. IJSBA Stock Class Legal.
Description
RIVA Yamaha 1.8L N/A Engine Intake Manifold
Upgrade Kit (VXR/VXS)
Part No.
RY12055-IMUK
RIVA FX-SHO/FZR/FZS INTAKE
MANIFOLD UPGRADE KIT
RIVA’s Intake Manifold Upgrade Kit enables your engine to produce more
horsepower by delivering increased air flow and boost pressure (+1lb).
Precision tapered billet sleeve directly replaces restrictive mesh element in the
intake manifold. Provides improved low end punch and mid range pull through
a quick & easy installation. Includes detailed installation instructions.
NOTE: Testing has determined the stock ECU will compensate for the
increased boost provided by our Intake Manifold Upgrade Kit.
Description
RIVA FX-SHO/FZR/FZS
Intake Manifold Upgrade Kit
Part No.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
RIVA YAMAHA 1.8L N/A ENGINE
INTAKE MANIFOLD UPGRADE KIT
RY12040-IMUK
©2012 Hot Products. All rights reserved.
31
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • SUPERCHARGER
R&D FX-SHO/FZR/FZS C1
MONSTER CHARGER WHEEL
R&D’s new C1 11 Blade Series Monster
Compressor Wheel Kit for Yamaha
FX-SHO/FZS/FZR engines is new and improved
to deliver “horsepower you can feel” with instant
throttle response, improved mid range acceleration, and increased top end
performance. The R&D Monster Wheel replaces the stock wheels inefficient 5
blade design with an all new modern low profile, high flow, 11 blade high tech
design. Fits directly into the O.E.M. stock compressor housing with no
modifications. The C1-11 Monster works with the OEM intercooler, OEM fuel
injectors, OEM ignition system and the R&D Intake CFM Kit. Kit performs well
on 91 octane pump gasoline. Boost rated 7psi @ 7500rpm and 8.5psi @
7700rpm. Horsepower increases were professionally documented by
MOTEC AUSTRALIA.
• Increased boost pressure (3-3.5psi over stock @ 7700 rpm)
• Increased airflow (1.5-2 pound per minute gain)
• 25-30 Horsepower increase and 2 MPH Gain (with OEM ignition)
• 70 Horsepower increase (with Motec ECU, CFM kit, 91 pump gas)
• Precision balanced (turbo specs .012-.027 gram inches)
• Better throttle response, increased horsepower • Ultra easy installation
• 91 octane pump gas friendly • Inexpensive horsepower upgrade
The C1 Wheel Kit works excellent for recreational use applications retaining the
OEM ignition, fuel system, injectors, and intercooler. R&D has data logged and
documented the A.F.R. (air to fuel ratio) to be a conservative and safe 11.8-12.0
with the C1 wheel kit. R&D recommends that the R&D Power Core Intake
Manifold and intercooler CFM kit or the R&D Stage 1 Intercooler Kit be used
with the C1 wheel.
Description
Part No.
R&D FX-SHO/FZR/FZS C1 Monster Charger Wheel
R&D FX-SHO/FZR/FZS C3
MONSTER CHARGER WHEEL
R&D’s new C3-11 Blade Series Racing Monster
Compressor Wheel Kit for Yamaha FX-SHO/FZS/FZR
engines is an exciting new racing product that will
deliver “horsepower you can feel” with instant throttle
response, aggressively improved low and mid range
acceleration, and increased top end performance. The R&D Monster Wheel
replaces the stock wheels low performing 5 blade design with a modern low
profile, high flow 11 blade high tech design with a larger exducer diameter to
move more air flow at lower rpm’s producing better holeshot horsepower. The
R&D C3 Monster Wheel and R&D Exducer Seal Plate Kit will install directly into
the O.E.M. stock compressor housing with no modifications. The C3 Racing
Monster will require the R&D High Performance Intercooler Kit, and an R&D
Impellor upgrade. The C3-11 performs well on 91 octane pump gasoline. Boost
rated 10psi @ 7700rpm and 13psi @8300rpm. The new R&D 11 blade series
compressor wheels offer the highest levels of airflow and horsepower gains
available for the 1.8 Yamaha engine using the stock E.C.U.
• Increased boost pressure (5psi over stock @ 7700 rpm)
• Increased airflow (2.5-3 pound per minute gain)
• 35+ Horsepower increase and 2 MPH Gain (with stock ECU)
• 300+ Horsepower using aftermarket ECU (MOTEC)
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. ignition system with R&D Impellor Upgrade
• Utilizes O.E.M. fuel injectors • 91 octane pump gas friendly
NOTE: The C3 Monster Wheel Kit will require pump impellor upgrades over the
C1 impellor suggestions.
Description
R&D FX-SHO/FZR/FZS C3 Monster Charger Wheel
32
612-25001
©2012 Hot Products. All rights reserved.
Part No.
612-25003
R&D SHO/FZR/FZS
C5 MONSTER
CHARGER WHEEL
The new “drop-in” R&D C5 Monster
Compressor Wheel and Exducer Seal Plate Kit installs directly into the OEM
supercharger without any modification. The new C5 delivers “horsepower you
can feel” with instant throttle response, aggressively improved low and mid
range acceleration, and intensified top end performance. The new C5 features
a light weight, high flow, 8 blade design with 8 supporting splitter veins and an
increased exducer diameter over stock. R&D’s large exducer diameter and
aggressive blade design is the key to improving CFM airflow volume throughout
the RPM range. The oversized exducer diameter increases the size of the
supercharger by enhancing air pumping volume and efficiency. The C5 out
performs any OEM sized compressor wheel in its boost pressure classification.
The R&D Monster Wheel Kit produces 14-15 pound per minute airflow gain
with a solid 15-16 pounds of boost pressure @ 8400-8500 rpm, 17+ @ 87008800 rpm. The new drop-in R&D C5 also offers superior off throttle surge
reduction over other 15-16 pound boost wheels. The new R&D C5 series
compressor wheels offer the highest levels of airflow and horsepower gains
available for the 1.8L Yamaha engine in the 15-17 pound boost range. A
properly tuned C5 set up (with supporting modifications) can produce well over
325 horsepower. In addition, no other rotating group on the market is lighter or
more powerful than the new C5 Monster Wheel combined with the R&D Billet
Supercharger Shaft.
In sum, the R&D C5 Monster Wheel and Shaft weighs less, has less surge,
rockets to 80 in less seconds and carves through corners in less time than any
other wheel and shaft in its class. Hit the throttle, hang on and discover the
astounding sensation that’s called Power!
• Aggressive throttle response, increased horsepower
• Increased boost pressure (10psi over stock @ 8500 rpm)
• Increased airflow volume (14-15 pound per minute gain)
• 100+ horsepower increase (with R&D R3 ECU)
• 325+ horsepower using aftermarket ECU
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. Reprogrammed R3 ECU ignition system
• Utilizes O.E.M. fuel injectors w/R&D RRFPR, R3, and Powershot
• 91 octane pump gas friendly with R3 ECU
• Less weight and surge
• Easy installation
C5 Modification Requirements:
R&D High Performance Pro Series Intercooler Kit w/R&D Greddy BOV
R&D Rising Rate Fuel Pressure Regulator Kit
R&D R3 ECU upgrade to allow 8500-8850 RPM
R&D Powershot
R&D Engine/intercooler Cooling Kit
R&D Twin Prop
NOTE: The C5 Monster Wheel will work best in sea level to 2000 ft. elevations,
or in ambient air temperatures between 60 and 100 degrees. NOTE: The C5
Monster Wheel Kit will require serious impellor upgrades.
Description
SHO/FZR/FZS C5 Monster Charger Wheel
Part No.
612-25005
YAMAHA FX-SHO & FZ • SUPERCHARGER
• Aggressive throttle response, increased horsepower
• Increased boost pressure (+12psi over stock @ 8700 rpm)
• Increased airflow (17.5-18.5 pound per minute gain)
• 150-175 horsepower increase
• Aftermarket ECU REQUIRED (MOTEC M400/ViPEC)
• Aftermarket R&D Fuel Injectors REQUIRED
• Aftermarket R&D RRFPR REQUIRED
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. fuel injectors w/R&D RRFPR, R2 and Powershot
• VP C12 octane RACE gas friendly
• Easy installation
C8 Modification Requirements:
R&D High Performance Pro Series Intercooler Kit w/R&D Greddy BOV
R&D Rising Rate Fuel Pressure Regulator Kit
R&D R3 ECU upgrade to allow 8500-8850 RPM
R&D Powershot
R&D Engine/intercooler Cooling Kit
R&D Twin Prop
NOTE: The R&D C20X Monster Compressor Wheel delivers a 17.5-18.5 pound
per minute airflow gain (approximately 150 plus horsepower at sea level at
8500 rpm’s). Pound per air volume gain is based on the rate of 1 pound of air
gain per minute for every 8-10 H.P. gain. The C20X Monster Wheel will work
best in sea level to 2000 ft. elevations, or in ambient air temperatures between
60 and 100 degrees. R&D strongly suggests that the R&D High Performance
Racing Intercooler Kit, Aftermarket ECU, R&D RRFPR be installed with the
C20X Kit. Trust the pros at R&D to boost up your airflow volume, after all, its
airflow volume gains that increase horsepower. NOTE: The C20X Monster
Wheel Kit requires serious pump impellor upgrades.
NOTE: The C8 Monster Wheel will work best in sea level to 2000 ft. elevations,
or in ambient air temperatures between 60 and 100 degrees. NOTE: The C5
Monster Wheel Kit will require serious pump impellor upgrades.
Description
FZR C8 Monster Charger Wheel
Part No.
612-25008
Description
Part No.
C20X Monster Wheel And Exducer Kit Only
C20X Monster Wheel And Exducer Kit with
Machining Service to your Front Housing
Watercooled Supercharger Cover for C20X
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Boost rating: 12psi @ 7800rpm, 15/16psi @ 8400-8500rpm, 17psi @
8700-8800rpm, 18psi @ 9200-950rpm.
BODY
• Aggressive throttle response, increased horsepower
• Increased boost pressure (12psi over stock @ 8800 rpm)
• Increased airflow volume (14-15 pound per minute gain)
• 100+ horsepower increase (with R&D R3 ECU)
• 350+ horsepower w/supporting parts
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. Reprogrammed R3 ECU ignition system
• Utilizes O.E.M. fuel injectors w/R&D RRFPR, R3, and Powershot
• 91 octane pump gas friendly with R3 ECU
• Less weight and surge
• Easy installation
EXHAUST
Less is More
In sum, the R&D C8 Monster Wheel and Shaft weighs less, has far less surge
over competitors’ wheel kits, rockets to 80 in less seconds and carves through
corners in less time than any other wheel and shaft on the planet. Hit the
throttle, hang on and discover the astounding sensation that less IS more
…much, much more.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
The new R&D C8 series compressor wheels offer the highest levels of airflow
and horsepower gains available for the 1.8L Yamaha engine. A properly tuned
C8 set up (with supporting modifications) can produce well over 325+ horsepower. In addition, the rotating group of the new C8 Monster Wheel combined
with the R&D Billet Supercharger Shaft is the undisputed Light Weight Champ,
no other rotating group on the market is lighter or more powerful.
ENGINE/
GASKETS
The R&D Monster Wheel Kit produces 18 plus pounds of boost pressure @
8700-8900 rpm, 16+ @ 8500-8600 rpm. The new drop-in R&D C8 also offers
superior off throttle surge over other 16-18 pound boost wheels. Less surge
increases supercharger clutch reliability.
Twenty pounds of boost now available. R&D’s
leading the way in performance with the new
C20X Racing Monster Compressor Wheel Kit
for the Yamaha FX-SHO, FZ, and FZR. The
C20X delivers arm stretching power like you
have never experienced. The C20X pumps
out 18 pounds of boost @ 8500-8700 rpm
and 20 pounds of boost @ 9000 rpm with a
17.5-18.5 pound per minute airflow gain
through its high flow 8 blade wheel design featuring oversized inducer and
exducer wheel diameters. R&D’s large inducer and exducer wheel diameters
along with an aggressive blade design are the key to improving CFM airflow
volume throughout the RPM range. The oversized inducer and exducer
diameters increase the size of the supercharger by enhancing air pumping
volume and efficiency. After all, its airflow volume gains that increase
horsepower. The C20X Racing Monster wheel requires the R&D High
Performance Pro Series Intercooler Kit, R&D 1000cc Fuel Injectors, R&D
Rising Rate Fuel Pressure Regulator Kit, and an aftermarket ECU (MoTeC or
ViPEC) upgrade to allow proper engine tuning. R&D also suggests upgrading to
R&D Forged Racing Rods and Performance Pistons. The new R&D C20X is for
Racing use only and requires 110 octane racing fuel. Boost rated to 18 plus at
8500-8700 and 20 pounds at 9000. The new R&D C20X series compressor
wheels offer the highest levels of airflow and horsepower gains available for the
1.8 Yamaha engine. Aftermarket ignition systems and a C20X Monster properly
tuned can achieve up to 400 Horsepower.
The new C20X will require a shop service to bore out your compressor front
housing to except the larger C20X compressor wheel. For those customers that
have previously purchased the C5-11 and already have the shop service to the
compressor front housing, just order the C20X wheel kit and change out the
wheel. No other supercharger compressor wheel kit has stolen more holeshots
and won more National and Offshore Titles than the R&D Monster Wheel Kits.
If 20 pounds of boost is truly what you’re looking for, well look no further and
just give us a call. The new C20X has been tested against all other existing
wheels on the market and is guaranteed to blow them away!
INATKE
SYSTEMS
The new “drop-in” R&D C8 Monster
Compressor Wheel and Exducer Seal
Plate Kit installs directly into the OEM
supercharger without any modification.
The new C8 delivers “horsepower you
can feel” with instant throttle response,
aggressively improved low and mid range acceleration, and intensified top end
performance. The new C8 features a light weight, high flow, 8 blade design with
8 supporting splitter veins and an increased exducer compression height over
stock. R&D’s larger exducer height and aggressive blade design is the key to
improving CFM airflow volume throughout the RPM range. The increased
exducer height dimension increases the size of the supercharger by enhancing
air pumping volume and efficiency. The C8 out performs any OEM sized
compressor wheel in its boost pressure classification. After all, its airflow
volume gains that increase horsepower.
YAMAHA
4 STROKE
R&D FX-SHO/FZR/FZS
C20X MONSTER WHEEL
R&D FX-SHO/FZR/FZS
C8 MONSTER WHEEL
612-25006
612-25007
612-24001
©2012 Hot Products. All rights reserved.
33
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • SUPERCHARGER
R&D now offers the new C19 Monster Pro Limited Wheel Kit. The new Billet
C19 Monster Compressor Wheel is specifically developed to pump maximum
boost and CFM possible utilizing the O.E.M. compressor housing. R&D has
taken full advantage of the IJSBA’s new rule allowance to change out the
compressor wheel backing plate to an aftermarket part. R&D has increased the
exducer size and deck area to pump as much air as the stock housings will
possibly allow with bolt in parts. The C19 pumps out 19 pounds of boost @
8600-8800 rpm and up to 20 pounds of boost @ 9000 rpm. The C19’s large
exducer wheel diameters along with an aggressive blade design are the key to
pumping more CFM airflow volume throughout the entire RPM range. The new
R&D C19 series compressor wheels offer the highest levels of boost, CFM
airflow, and horsepower gains available for the 1.8 Yamaha engine in Pro
Limited Class category. The R&D C19 Monster Wheel, R&D Racing Camshafts,
and a properly tuned fuel and E.F.I. system can achieve up to 400 horsepower.
If “Max Boost” is truly what you’re looking for, look no further and give the pro’s
at R&D a call. The new C19 has been tested against all other existing wheels
on the market that fall into Pro Limited Class Specs, and is guaranteed to out
boost and out power them all! The C19 wheel requires the use of an intercooler
system capable of flowing 500 CFM (Most on the market are not even close to
500 CFM and are restrictive). R&D suggests the use of an R&D Racing
Intercooler Kit (600+ CFM rated), R&D Rising Rate (adjustable) Fuel Pressure
Regulator Kit, R&D Super Clutch System and an R&D Pro Limited ECU
Program upgrade to ensure proper engine tuning, and proven (safe) rev control
functions. R&D also suggests upgrading to R&D 8.6-1 Forged Racing Pistons.
• Aggressive throttle response, increased horsepower
• Increased boost pressure up to 20 pounds
(boost will vary depending on cam spec data)
• Increased airflow (20 pound per minute gain over stock)
• 150-175 horsepower increase over stock @205-210)
(depending on cam spec data)
• R&D ECU Reprogramming REQUIRED (specify fuel type)
• R&D aftermarket fuel pump system REQUIRED
• R&D fuel pressure regulator REQUIRED
• VP MS109 octane RACE gas friendly
NOTE: The R&D C19X Monster Compressor Wheel delivers 41-42 pounds of
air per minute, that’s and additional 20 pound per minute airflow gain over a
stock compressor. Pound per air volume gain is based on the rate of .9 pound
of air gain per minute for every 8-10 H.P. gain. The C19 Monster Wheel will
work best in sea level to 2000 ft. elevations, or in ambient air temperatures
between 60 and 100 degrees. The C19 Monster Wheel Kit power output will
require serious pump assembly, impellor, and compression nozzle upgrades.
Call R&D for the latest in pump assembly and impellor suggestions.
Description
R&D Billet C19 Monster Wheel Kit
34
R&D FZR C24 MONSTER WHEEL & WATER
COOLED COMPRESSOR HOUSING KIT
R&D FZR C19 MONSTER
PRO LIMITED WHEEL KIT
©2012 Hot Products. All rights reserved.
Part No.
612-25009
R&D now offers the new C24 Monster Wheel & Water Cooled Compressor
Housing Kit. The new Billet C24 Monster Compressor Wheel and Water-cooled
Housing System can pump up to 24 pounds of boost utilizing the OEM cams
and cam timing. The C24 pumps out 20-22 pounds of boost @ 8600-8800 rpm
and 24 pounds of boost @ 9000 rpm. The C24’s large inducer and exducer
wheel diameters along with an aggressive blade design are the key to pumping
more CFM airflow volume throughout the entire RPM range. The R&D C24
series compressor wheels offer the highest levels of airflow and horsepower
gains available for the 1.8 Yamaha engine. The R&D C24 Monster Wheel, R&D
Racing Camshafts, and a properly tuned ECU and E.F.I. system can achieve
well over 425+ horsepower. The C24 Water Cooled system was used by Ron
Allison to win the 2011 HydroDrag Pro Super Stock Speed Alley competition.
The C24 wheel requires the use of an intercooler system capable of flowing
500-600 CFM. (Most on the market are not even close and are restrictive)
R&D suggests the use of an R&D High Performance Intercooler Kit (600 cfm
plus rated), R&D 1000cc Fuel Injectors, R&D Rising Rate (adjustable) Fuel
Pressure Regulator Kit, and an R&D R12 ECU Program upgrade to the stock
ECU to ensure proper engine tuning, and proven (safe) rev control functions.
R&D also suggests upgrading to R&D Forged Racing Rods and Performance
Pistons.
• Aggressive throttle response, increased horsepower
• Increased boost pressure up to 24 pounds (boost will vary depending on
cam spec data)
• Increased airflow (26 pound per minute gain over stock)
(49 pounds total at 450 h.p.)
• 220-240 horsepower increase over stock @205-210
(with supporting modifications)
• R&D R12 ECU Reprogramming REQUIRED
• R&D 1000cc Fuel Injectors REQUIRED
• R&D fuel pressure regulator REQUIRED
• VP C12 octane RACE gas friendly
• Installs on to the OEM Supercharger with no modifications
NOTE: The R&D C24X Monster Compressor Wheel delivers a 49-50 pounds of
air per minute, that’s and additional 26 pound per minute airflow gain over a
stock compressor. Pound per air volume gain is based on the rate of .9-1 pound
of air gain per minute for every 8-10 H.P. gain. The C24 Monster Wheel will
work best in sea level to 2000 ft. elevations, or in ambient air temperatures
between 60 and 100 degrees. The C24 Monster Wheel Kit power output will
requires serious pump assembly, impellor, and compression nozzle upgrades.
Call R&D for the latest in pump assembly and impellor suggestions.
Description
R&D Billet C24 Monster Wheel and Water Cooled
Compressor Housing Kit
R&D Billet C24 Monster Wheel Kit
Part No.
612-25010
612-25011
YAMAHA FX-SHO & FZ • SUPERCHARGER
YAMAHA
4 STROKE
INATKE
SYSTEMS
RIVA FX-SHO/FZR
SUPERCHARGER IMPELLERS
The system features a High Performance Volute (intake air path), Internal
Anti-Surge Port, 100% Water-Cooling and a custom R&D Power Plenum Air
Filter. Now since the Supercharger is the coolest part in the engine
compartment and runs at lake temperature, it only made since to design a
custom R&D Power Plenum Air Filter that would take full advantage of the new
found cool air, now located directly in front of the Supercharger.
NOTE: Both impellers require use of aftermarket engine management system
for proper calibration
Description
RIVA FX-SHO/FZR S/C Impeller - 11.5 psi
RIVA FX-SHO/FZR S/C Impeller - 16 psi
Part No.
RY17040-SCI-B1
RY17040-SCI-E1
System installs in 45 minutes and comes complete with all necessary
hardware and pictorial instructions.
Fitment: The R&D Water-Cooled System fits all supercharger wheels that fit
into the OEM charger housing.
Part No.
R&D SHO/FZR/FZS Water-Cooled OEM
Supercharger System for (C1, C3, and C5)
R&D SHO/FZR/FZS Water-Cooled
Supercharger System (For C20X)
612-24000
612-24001
R&D SUPERCHARGER
BLOCK-OFF PLATE
The R&D Supercharger Block-off
Plate is designed to seal the case
on the front of the engine that is
exposed when the supercharger is
removed for a Turbo.
Description
R&D Supercharger Block-off Plate
Part No.
612-19100
The 'H1' Race Charger was designed for serious racers and tuners who
demand the ultimate performance gains. H1 Impeller and housing combo
delivers 20psi of boost pressure at 8,500rpm producing up to 400hp on
modified engines. High performance impeller and housing combo increase
horsepower through superior blade design and larger interior housing volume.
Impeller features a sophisticated HKS blade design that is precision balanced
for smooth operation. Requires aftermarket ECU and upgraded engine
components for proper calibration and durability.
FOR COMPETITION USE ONLY. RIVA Racing is not liable for possible
damage to associated parts or labor costs incurred due to the installation of
this racing component.
Performance Data:
• 16.5psi @ 7,500rpm • 17psi @ 7,700rpm
• 18psi @ 8,000rpm • 20psi @ 8,500rpm
Description
RIVA FX-SHO/FZ 'H1' Race Charger
Impeller & Housing
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Description
RIVA FX-SHO/FZ 'H1' RACE CHARGER
IMPELLER & HOUSING
BODY
Performance Benefits: Up to 200° F cooler supercharger temperature,
cooler and denser intake air, decreased engine compartment temperature,
improved clutch life through Internal Anti-Surge Port, increased RPM (up to
200 rpm), increased boost pressure, improved top speed, no heat fade,
consistent peak engine rpm.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
R&D is proud to announce the new Water-Cooled Supercharger Housing
System. The new R&D Water-Cooled Supercharger System is fully water
jacketed and eliminates heat at its source, the Supercharger. The new
system replaces the OEM inducer cover and mounts directly to the OEM
Supercharger body.
EXHAUST
Ever wonder why the supercharger is so HOT? Heat is a derivative of
compressed air (boost). The more boost pressure, the hotter the supercharger
gets. The engineers at R&D understand the key in producing more horsepower
and maximizing performance, is managing heat.
ENGINE/
GASKETS
R&D FZR WATER-COOLED
SUPERCHARGER SYSTEM
RIVA Racing released the ultimate (drop-in) performance supercharger
impellers for the Yamaha 1.8 liter FX-SHO Engine! Working closely with
Vortech Engineers, RIVA designed these impellers to deliver more horsepower
and torque throughout the RPM range resulting in excellent acceleration and
top speed. Investment cast from an extremely strong, lightweight proprietary
aluminum and CNC machined to ensure exact tolerances. All new blade
design is optimized aerodynamically and precision balanced to deliver smooth
operation. Installs easily into stock supercharger housing with no modifications
required. Includes detailed installation instructions.
B1 produces 11.5psi @ 7,700rpm • E1 produces 16psi @ 8,000rpm
Part No.
RY17040-IH-H1
©2012 Hot Products. All rights reserved.
35
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • SUPERCHARGER
R&D YAMAHA
SHO/FZR BILLET
SUPERCHARGER
SHAFT KIT
ENGINE-TECH YAMAHA FZR
SUPERCHARGER IMPELLER
This is a drop in impeller so no modifications to
the housings are necessary. Weighing a mere
106 grams this is the lightest impeller on the
market reducing wear and tear on the
clutch/shaft assembly. Output is 15+ psi @7700
rpm and an amazing 18+psi @8500 rpm.
Must be used with adjustable fuel regulator, high flow intercooler and ECU
(Motec or equiv, Motec map available upon request)
Description
Part No.
ETYAMSHO
Engine-Tech FZR SC Impeller (18+ lbs)
A.
R&D SPECIALTY
SUPERCHARGER TOOLS
R&D has designed custom tools that are
essential in the rebuilding process of the
Yamaha Supercharger. All tools are specific
in application and are CNC machined to
ensure a precision job.
B.
Description
A. Supercharger Housing Holder Bracket Tool
B. Shaft/Gear Holding Tool
Part No.
612-92010
612-92011
RIVA YAMAHA
FX-SHO/FZ
HEAVY DUTY SHAFT
UPGRADE KIT
RIVA Heavy-duty Supercharger
Shaft Upgrade Kit delivers increased strength & reliability to your Yamaha SC
System. Upgraded shaft & bearings directly replace OEM parts for maximum
durability in performance applications. Manufactured exclusively for RIVA by
HKS, these components feature superior materials & finishing treatments for
reduced friction and abrasion resistance.
R&D's new High Performance
Billet Supercharger Shaft
eliminates the weak design features of the OEM and aftermarket HKS
supercharger shafts. After analyzing the OEM HKS shaft design and sorting
through the various failures we had with it while testing our popular Monster
S/C Wheels, we developed a superior shaft design. The new R&D shaft is not
a copy of the fragile HKS design. Rather, it is a completely new design,
superior in material strength and improved in every way. The new R&D Shaft
is precision CNC machined, heat treated, and precision ground from billet steel
alloy. Featuring a uni-structure design that incorporates the shaft and gear as
one billet piece, much like a transmission shaft. This eliminates the fracture
point on the OEM design where the gear shears off the end of the shaft. The
billet design will not allow the gear to slip under high boost loads like the
pressed on OEM gear.
Next R&D increased the inadequate 6mm thread diameter on the OEM shaft
to utilize a well proven “Turbo spec” LARGER 5/16-24 left handed thread that
will not break under extreme conditions. The larger thread diameter will also
allow wheel torque specs to be increased safely.
Lastly, R&D reduced the weight of the R&D Supercharger shaft by eliminating
the hex nut on rear the gear and lightened the end of the shaft/gear inside
diameter to significantly reduce reciprocating weight. We all know what that
will do to add to clutch performance. Kit comes complete with larger nut and
installation instructions. All in all, the new R&D High Performance Billet Racing
Shaft is not just a replacement shaft, but a solution to end all supercharger
shaft problems.
Description
A.
Key benefits include:
• Reduced friction between moving parts • Increased fatigue strength in parts
• Higher resistance to surface abrasion • Improved seize resistance
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
Kit includes supercharger shaft, 2 bearings, shaft nut and instructions.
Description
Part No.
RIVA Heavy-Duty SC Shaft Upgrade Kit
RY17040-UK-6S5
RIVA FX-SHO/FZ HEAVY DUTY
SUPERCHARGER BEARING
RIVA’s heavy duty one-piece bearing features
increased surface area providing improved torsional
stability of supercharged shaft. Bearing is constructed
with superior materials & finish treatment for reduced friction & abrasion
resistance. Compatible with all RIVA Supercharged Shaft Kits as well as OEM
supercharger shaft.
Description
Part No.
RIVA Heavy-Duty Supercharger Bearing RY17040-HDSCB-6S5
36
©2012 Hot Products. All rights reserved.
Part No.
R&D FX-SHO/FZR Billet Supercharger Shaft Kit
612-25020
R&D FX-SHO/FZR
HIGH PERFORMANCE
SUPERCHARGER
REPLACEMENT THRUST
BEARING/SEAL KITS &
DUPLEX BEARING KIT
R&D offers an answer to both repairing & upgrading the O.E.M. superchargers
vulnerable thrust bearing and main shaft bearing assemblies. Engines with
superchargers running higher boost pressures and higher rpm frequencies will
eventually need bearing servicing. Servicing the supercharger main bearings
periodically or upgrading to R&D’s new “Duplex Bearing System” will extend
the life of the superchargers thrust bearing significantly. R&D offers both
standard replacement bearing kits, and the new “Duplex Bearing Kit” that will
work in any Yamaha supercharger. R&D also offers complete rebuild kits for
stock superchargers running C1 Monster Wheel Kits and all supercharger
wheel kits using the stock exducer size. R&D also offers rebuild kits for all C3,
C5, C7 Monster Wheel Kits with larger exducers.
Description
Part No.
A. OEM Replacement Bearing Kit (stock/ltd class legal) 612-25025
Supercharger Rebuild Kit with OEM
612-25028
Exducer/Thrust Bearing Assembly Kit
Supercharger Rebuild Kit with C3/C5
612-25030
Exducer/Thrust Bearing Assembly Kit
YAMAHA FX-SHO & FZ • SUPERCHARGER
Key Features Include:
• Dampener mechanism protects supercharger drive gears.
• Improves sprag clutch durability.
• Stronger materials and thicker gear teeth than OEM.
• Directly replaces OEM intermediate gear.
• No auxiliary clutch systems or maintenance required.
• Superior bearing material & thickness.
• Use with new style 2011/12 Yamaha clutch and RIVA Supercharger
Shaft Kits.
• Manufactured exclusively for RIVA Racing by HKS.
Description
RIVA Supercharger Gear Dampener
Part No.
RY17040-SGD-6S5
Technology and Design performance make this Super Clutch the finest and
most effective clutch system available. Order yours today, and Crank up the
Boost!
Performance Features:
• Heavy Duty, Bionic Strong, Billet Steel Construction
• Heat Treated, Precision Ground, and Low Friction Polished
• Super Clutch 2-Way System Eliminates the Forces that Cause Premature
OEM Sprag Clutch and Gear Failures
• Adjustable for ANY Boost Pressure
• Through-Shaft Oil Pressure Lubricated Bearings and Clutch
• 15% Lighter than OEM Drive Gear Rotating Mass
• Directly Replaces OEM Drive Gear
• Compatible with all years of OEM Clutches
• Compatible with all OEM/Aftermarket S/C Shafts
• Easy Clutch Adjustments with Supplied Tool Kit
• No Modification Required to Install
Description
R&D Yamaha Superclutch Drive Gear
*Available early Summer 2012
Part No.
612-19300
©2012 Hot Products. All rights reserved.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
RIVA’s damper unit is designed to protect gear teeth
& sprag clutch on supercharger drive system.
Dampener features innovative cushioning mechanism
that insulates gears from harsh clutch engagement.
Directly replaces OEM intermediate gear located
between clutch and supercharger shaft. Constructed
with superior materials and thicker gear teeth than OEM. Designed to be
used with new style 2011/12 Yamaha clutch (part# 6S5-17800-10-00) and
RIVA Supercharger Shaft Upgrade Kits.
This is a bolt-on clutch upgrade. There is no machine work required to install.
The Super Clutch is compatible with all years of OEM Sprags clutches and all
OEM or Aftermarket Yamaha supercharger shafts.
BODY
RIVA SUPERCHARGER
GEAR DAMPENER
The clutch discs are precision machined, heat treated, and ground to exact
tolerance utilizing only the finest materials tested and proven to be the best in
these type systems. The clutch is adjustable for any boost pressure.
EXHAUST
Part No.
RY17040-UK-6S5-3
This system features a unique billet steel
Gear-Hub design that uses a high pressure
through-shaft oiling technique to lubricate the
drive gear bearings and clutch friction discs. The 50 tooth Drive Gear is
also machined from billet steel alloy, heat treated for ultimate strength and
hardness, and the tooth profile is CNC precision ground to Yamaha
specifications. The clutch surfaces of the gear feature special “oil-holding”
wiper slots that provide improved oiling to increase lubrication to the clutch
discs. Knowing the detriment to the Sprag clutch of a heavy Drive Gear, we
designed the Super Clutch Drive Gear with 6 lightening window pockets to
have the least amount of rotational weight. The complete system tips the
scales at only 382.8 grams, that’s 15% lighter than the OEM Drive Gear.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
RIVA ‘Gen-3’ Super-Duty Supercharger
Shaft Kit for FZR/FZS & FX-SHO
The R&D Super Clutch Drive Gear System is CNC
machined from premium billet steel alloy, heat
treated for Bionic strength and hardness, precision
ground to strict aircraft tolerances, and polished for
a low friction finish.
ENGINE/
GASKETS
Key Features Include:
• Hydraulic end bearing minimizes shaft deflection.
• Through-shaft oiling system maximizes lubrication.
• Braided stainless steel oil line delivers additional lubrication.
• One piece shaft/collar/gear construction.
• Stronger billet material & superior surface finish.
• Larger diameter threads & nut.
• One-piece bearing improves shaft stability.
• Bolt-on installation (no machining required).
• Manufactured exclusively for RIVA Racing by HKS.
The R&D engineering staff has spearheaded
another industry first. We are proud to introduce
the new Revolutionary R&D Super Clutch Drive
Gear System. This is the first Yamaha Drive Gear
that features a clutch system. The Super Clutch
Drive Gear has a “Double Action” 2-way clutch
system that utilizes an “Oil-Loaded” Friction Disc
Design which cancels and neutralizes constantly
changing rotational mass energies, and aggressive
moment-of-inertia shock loads that cause
premature OEM Sprag clutch and gear failures.
INATKE
SYSTEMS
RIVA’s Super-Duty ‘GEN-3’
Supercharger Shaft Kit provides the
ultimate in reliability for high boost applications. Kit features a revolutionary
hydraulic shaft stabilization bearing that limits shaft deflection and wear.
Bearing stabilizes end of supercharger shaft via high pressure oil film
dramatically increasing the stability of the system. Hydraulic end bearing and
one-piece shaft bearing are fed by a through-shaft oiling system providing
superior lubrication. Oil is delivered by braided stainless line and injected into
a billet end cap that houses hydraulic bearing. Shaft is precision machined
from a single piece of highstrength billet steel producing shaft, collar & gear
as one piece. This eliminates the common failure point on stock shafts where
OEM gear is pressed onto shaft. Shaft also features larger diameter threads
& nut for added strength. Kit includes new one piece bearing with increased
surface area providing improved torsional stability of shaft. Bearing features
superior materials & finish treatment for reduced friction & abrasion resistance. This Shaft & Bearing Kit is a direct replacement for OEM parts and
requires no additional modifications for use.
R&D YAMAHA SUPERCLUTCH
DRIVE GEAR
YAMAHA
4 STROKE
RIVA ‘GEN-3’
SUPER-DUTY
SUPERCHARGER
SHAFT KIT
37
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • SUPERCHARGER
38
R&D YAMAHA
SUPERCLUTCH
The R&D Superclutch elevates all clutch
performance aspects to a higher level. The
Superclutch is a supplemental clutch system
that is designed “specifically” for the Yamaha to be used along with the OEM
Sprag drive system. The R&D clutch design utilizes an “Oil-Loaded” Friction
Disc design which will dampen constantly changing rotational mass energies,
and aggressive moment of inertia shock loads that have proven to over stress
the OEM Sprag clutch drive and cause failures.
The new R&D Superclutch and shaft system is CNC machined from premium
billet steel alloy, heat treated, and precision ground between centers to strict
aircraft tolerances. This R&D system features a unique one-piece billet shaft
design that utilizes a proven high pressure, through-shaft oiling technique to
lubricate the billet drive gear bearing, clutch system friction discs, and the “all
important” additional rear third bearing. The Superclutch shaft features (an
R&D standard) oversized threads and a flanged nut proven in design to not
fatigue or break under extreme conditions and allows charger impellor torque
specs to be increased safely.
The R&D Superclutch drive gear is machined from billet steel alloy, heat
treated for proper hardness, and the tooth profile is precision CNC ground to
OEM Yamaha specifications. The clutch surfaces of the R&D gear features
special “oil-holding” wiper slots that provide improved oiling to increase
lubrication to the clutch discs. The R&D clutch discs are precision machined,
heat treated, and ground to exact tolerance utilizing only the finest materials
tested and proven to be the best in these type systems.
The R&D third bearing support design is integrated into a new back housing
cover machined from billet aluminum with a creative precision alignment
flange to insure 100% trueness and support to the third bearing. The third
bearing assembly adds a tremendous amount of shaft support which will keep
the shaft in line and free from the stresses of “gear climb”. The third bearing
assembly will also relieve stresses on the chargers main thrust system. For
Periodic clutch maintenance and adjustments, R&D has made it easy. The
clutch slip can be adjusted easily, and clutch discs inspected and or changed
out without removing the shaft from the supercharger with the special tool kit
provided with each system.
Minor machine work is required to the rear of the supercharger housing in
order to achieve proper drive gear alignment (mating to the jack gear) and to
true up the back cast surface so the third bearing housing cover mounts
precision and true to the shaft centerline position. Machining is available from
R&D, or your local machine shop can follow the kit supplied blue print.
R&D
SUPERCHARGER
CLUTCH REMOVAL
TOOL
This R&D tool enables the clutch to be changed in a
matter of only minutes. With the supercharger and
front engine cover removed the tool drops down
through the case and secures the drive gear at the
front of the crankshaft from rotating when the clutch
is removed and installed. This is a “must have” tool
that will save massive amounts of time for any mechanic.
Description
R&D Supercharger Clutch Removal Tool
Part No.
612-92012
R&D FRONT COVER GASKET
R&D’s new Front Cover Gasket features a metal
reinforced center that enables it to be reusable when
servicing the supercharger clutch.
Description
R&D Front Cover Gasket
Part No.
080-21024
R&D FX-SHO/FZR/FZS
SILICONE INTAKE HOSE KIT
The R&D Yamaha FX-SHO/FZR/FZS
Supercharger High Performance Hose Kit was
developed while testing the R&D Monster
Compressor Wheel Kits. Higher boost pressures create higher intake air
temperatures of up to 235 degrees. The O.E.M. standard black rubber hose
and standard hose clamps just do not hold up to the pressures and heat like
high quality, high temperature silicone hose and high strength stainless steel
T-bolt style hose clamps. The R&D “Blue Hose” is manufactured from high
performance, turbo charger quality high-temperature silicone. The R&D silicone
hose installs easily in place of the OEM rubber elbow hose, and T-bolt clamps
will keep the hose secure for the longest of endurance races.
Description
R&D FX-SHO/FZR/FZS Silicone Intake Hose Kit
Part No.
612-18007
Key Features Include:
• Precision one piece shaft design
• Billet drive gear with precision ground tooth profile to Yamaha Spec.
• Billet drive gear is precision oil sleeved (No needle bearings)
• Large turbo type compressor sized threads
• Unique clutch oiling system offers reduced clutch wear and galling
prevention
• Rear (3RD) bearing support system offers precision centering and alignment
• Rear (3rd) bearing reduces front thrust stack stress and premature wear
• Easy maintenance and adjustments allowed with No Main shaft
Disassembly
• Easy clutch adjustments and servicing with kit supplied tool kit
Description
R&D Competition Clutch-Shaft
R&D Clutch Disc Rebuild Kit
*Available early summer 2012
©2012 Hot Products. All rights reserved.
Part No.
612-19200
612-19201
2012 IJSBA HOT PRODUCTS MARK HAHN MEMORIAL
HAVASU 300 ENDURANCE RACE IN LAKE HAVASU CITY, ARIZONA
RACE START!
YAMAHA FX-SHO & FZ • SUPERCHARGER
Part No.
613-95263
612-18009
RIVA Performance Blow-off Valve Kit improves supercharger reliability and
performance by relieving unwanted pressure during off-throttle operation.
Reduces supercharger clutch & gear wear and eliminates heat soak in
discharge tube. High-strength silicone hose with integrated HKS valve
installs easily in place of OEM elbow joint. Includes high quality HKS Super
SQV (Super Sequential Blow Off Valve) that features unique sequential valve
structure and a differential pressure control system, allowing for a broad
operation boost range. Also includes vacuum line and fittings necessary for
installation on FX-SHO engine. A simple and cost effective upgrade for both
stock and modified engines.
Description
RIVA FX-SHO/FZR Performance Blow-off Valve Kit
Part No.
RY17040-BV
RIVA FX-SHO/FZR
BLOW-OFF VALVE KIT
High quality HKS Blow-off Valve reduces
wear and tear on clutch & drive gears of
supercharger and eliminates heat soak in
discharge tube. For use with RIVA FX-SHO/FZR
Power Cooler (part# RY17040-PC). HKS Super SQV (Super Sequential Blow
Off Valve) features unique sequential valve structure and a differential
pressure control system, allowing for a broad operation boost range.
Includes vacuum line and specific fittings necessary for installation.
Description
RIVA FX-SHO/FZR Blow-Off Valve Kit
Part No.
RY17040-BOV-SSQV
©2012 Hot Products. All rights reserved.
BODY
Description
A. R&D/Tial 50mm BOV Valve Only
B. R&D/Tial 50mm BOV Kit
RIVA FX-SHO/FZR PERFORMANCE
BLOW-OFF VALVE KIT
EXHAUST
• Aggressive throttle response, increased horsepower from a better seal
• Increased boost pressures over smaller valves that don’t seal well
• Improved valve action with larger diaphragm and variable spring control
• Improved clutch performance from reduced off throttle back pressures
• Precision sequential valve operation
• Installs easy and clean to the O.E.M. intercooler inlet/outlet
• Works well on R&D Pro Series Intercoolers
Part No.
612-18008
R&D FX-SHO/FZR Surge Protector Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D announces the release of the new
R&D/Tial 50mm Surge/Blow-off Valve Kit.
R&D has been committed to on going
research for any part that proves to be an
aid in reducing the inherent and well known
clutch issues related to running high
performance boost wheels and high boost
pressures in the Yamaha 1.8 Supercharged
engine. R&D has noticed a significant
B.
reduction in clutch related issues in high
boost ranges by “Going Big”. R&D engineers
have concluded through endurance testing
that the new 50mm R&D/Tial Valve with its
huge 50mm lightweight billet aluminum
piston, and 4 massive (bigger than any other valve) pressure relief ports, to
outperform the smaller (25-35mm) HKS Sequential, and 35mm Greddy RZ
Valves. The trick R&D has found with this valve is, in aggressive off throttle
situations with a gear driven supercharger the big Tial 50mm piston responds
quickly to allow the reduction of boost pressure which relieves back pressure
that can affect the clutch. The new 50mm design also has a much larger
diaphragm over HKS and Greddy, which helps the piston react quicker to
relieve pressure. If you are running Boost Wheels that produce over 15
pounds of boost, R&D strongly suggests looking into a larger valve setup. It
only stands to reason that with higher boost pressures, a larger valve can
allow quicker discharge of air volume. Valve kit comes complete with
Aluminum weld-on adaptor, o-ring seal, billet Aluminum V-clamp, and banjo
style vacuum fitting.
Description
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
R&D/TIAL 50MM
SURGE/BLOWOFF
VALVE KIT
ENGINE/
GASKETS
A.
INATKE
SYSTEMS
The R&D Yamaha FX-SHO/FZR Surge Protector
Kit will significantly improve supercharger clutch
and compressor wheel performance and
reliability by eliminating damaging compressor
surge. The R&D Surge Protection Kit utilizes an automotive vacuum assisted
Bosch pressure blow off valve that releases the unwanted intake pressure
between the throttle valve and the supercharger thus keeping the pressures in
P1 and P2 equal. As soon as the throttle valve is opened, the blow off valve
immediately closes and the compressor can supply its full boost potentials to
the engine. The R&D surge hose is manufactured from high performance,
high-temperature silicone with an integrated molded riser for the blow off valve
to function without hindering intake flow or velocity. The R&D kit installs easily
in place of the OEM rubber elbow joint with no modifications. The R&D
Pressure Port installs between the MAP sensor and the MAP sensor bracket
with a “bolt on” part. The R&D Surge Protection Kit is a necessary and cost
effective upgrade for the Yamaha FX-SHO/FZR supercharged engine. The R&D
kit comes completely assembled with silicone elbow, blow off valve, R&D B.O.V.
filter, mounting hardware and instructions.
YAMAHA
4 STROKE
R&D FX-SHO/FZR SURGE
PROTECTOR KIT
39
R&D FX-SHO/FZR STAGE 1
INTERCOOLER CORE KIT
The R&D Yamaha FX SHO/FZR Stage 1 Intercooler
Core Kit was developed to replace the over
restrictive OEM intercooler with an inexpensive direct
replacement core that will bolt in to the OEM stock
location with all stock hardware. The R&D Intercooler Core reduces the
deadhead air restriction (similar to the R&D Intake Core Kit) that is created
when installing a C1 Monster compressor wheel with a 3-4 pound boost
pressure gain. The R&D Intercooler offers better cooling efficiency with an
aluminum 8 core design.
•
•
•
•
•
Flows 40 CFM more than stock • 3 pounds lighter than stock
Improves cooling efficiency
• Bolts directly into stock location
Increases horsepower by reducing restrictions
Works great with C1 compressor wheel
Retains O.E.M. flushing system for maintenance
Description
R&D FX-SHO/FZR/FZS Stage 1 Intercooler Core Kit
Part No.
612-18001
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • INTERCOOLER
INTERCOOLER/SUPERCHARGER
LUBRICATION KIT
This kit will allow you to spray a aerosol lubricant of your choice into the
supercharger, intercooler and throttle body to prevent rust from the excess
moisture in the system. Complete instructions, pictures and a diagram
supplied for a simple installation.
Description
Part No.
Yamaha/Sea Doo Spray Nozzle Inlet for Lubrication IWCS-SSU
R&D YAMAHA FX-SHO/FZR
PRO LIMITED INTERCOOLER KIT
The R&D Yamaha FX-SHO/FZ/FZR Pro Limited Intercooler Kit was
developed to directly replace the restrictive O.E.M. intercooler. The new
R&D design offers high performance affordable intercooling that will bolt into
the OEM stock location utilizing the OEM inlet cover, and all stock hoses
and hardware.
The new R&D design is IJSBA & APBA Limited Class legal, complying with
rule book regulating aftermarket intercooler size. The R&D Intercooler has
been specifically designed, sized, and routed to also comply with the
I.J.S.B.A.’s 25% rule. The Intercooler Kit is constructed from aircraft
aluminum and is extremely easy to install, removes quick for cleaning and
winter storage, is ultra strong, and rubber mounted so vibration will not
compromise the long term performance. The R&D intercooler offers better
cooling efficiency through a aluminum core design that easily out performs
cheaper inefficient intercooler cores known to crack, leak and cause extreme
detonation. The R&D intercooler core will flow more air, deliver better cooling
efficiency, and allow C1 and C3 Monster Wheel to live up to their airflow
volume and power potential. The new R&D design drastically reduces
deadhead air restriction producing ultra responsive “POWER NOW”
acceleration all the way through the RPM range.
The R&D Pro Limited Intercooler Kit has also incorporated an integral flange
which will allow the easy bolt on addition of a Greddy RZ Blow-off valve
which can be adjusted to regulate boost, and compressor surge blow-off
under deceleration.
* Significantly improves cooling efficiency
* Flows 40 CFM more than stock
* Bolts directly into stock location w/oem hardware
* Increases overall horsepower
* Aggressive holeshot and mid range acceleration
* Works great with C1 or C3 Monster compressor wheels
* Retains O.E.M. flushing system for maintenance
* I.J.S.B.A. and A.P.B.A. Limited Class Legal (Rule 7.8.3.)
*7.8.3 AIR/FUEL DELIVERY — FOUR-STROKE (RUNABOUTS ONLY)
Turbocharger impeller or supercharger impeller may be modified or
aftermarket. The impeller housing must remain stock as supplied by the
manufacturer. Intercoolers may be modified or aftermarket. Intercooler
heat exchange surface area may not be increased by more than 25%.
Description
Part No.
R&D Yamaha SHO/FZ/FZR Pro Limited Intercooler Kit 612-18004
40
©2012 Hot Products. All rights reserved.
YAMAHA FX-SHO & FZ • INTERCOOLER
YAMAHA
4 STROKE
INATKE
SYSTEMS
R&D PRO SERIES RACING
INTERCOOLER KIT
Tested to easily allow 30 PSI of boost @ 90-100 degree air temp, the new
R&D Pro Series Racing Intercooler design drastically reduces deadhead air
restriction producing ultra responsive “POWER NOW” acceleration all the way
through the RPM range. All data and air temp was logged with a MoTeC
M400 with i2 logging software. It should be noted that pressure data was
taken in the plenum with the stock MAP sensor and backed up with a
mechanical gauge.
Part No.
RY17040-PC-1
• Significantly improves cooling efficiency
• Flows 90-100 CFM more than stock (allows 60 pounds of unrestricted air)
• Bolts directly into stock air box location w/O.E.M. studs and rubber
grommet hardware
• Increases overall horsepower (core size/area allows up to 600 horsepower)
• Aggressive holeshot and mid range acceleration
• Works great with any R&D Monster compressor wheels
• Retains O.E.M. flushing system for maintenance
• I.J.S.B.A. and A.P.B.A. Limited Class and Pro Open Legal
Description
R&D Pro Series Racing Intercooler Kit
BODY
Description
RIVA ‘Gen-2’ Power Cooler Kit
FX-SHO/FZ
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
The R&D Pro Series Racing Intercooler Kit also has an incorporated integral
flange which will allow the bolt on addition of an R&D/Tail Q Series 50mm
Blow-off valve (Pt. # 613-95263 sold separately) which superbly regulates
compressor surge or blow-off under deceleration.
EXHAUST
This new intercooler system has been tested against every manufacturer’s
current intercooler designs, and has proven to out flow, out cool, and out
perform them all. The R&D intercooler offers better cooling efficiency through
its “made in the USA” aluminum core design that easily out performs cheaper
inefficient intercooler cores known to crack, leak and cause extreme
detonation. The R&D Pro Series intercooler core will flow more air, deliver
better cooling efficiency, and allow C1-C24X Monster Wheels to live up to
their airflow volume and power potential.
RIVA ‘GEN-2’ POWER COOLER KIT
The RIVA ‘GEN-2’ Power Cooler intercooler system features a new
high-capacity cooler element that is rated for up to 500hp! Huge cooler core
resists heat soak under the most demanding high boost/high temperature
applications. Delivers an increase of 20 peak horsepower over OEM intercooler providing arm-wrenching results on the water. Quality manufacturing
of cooler core delivers minimal pressure drops and excellent thermal
efficiency. The cooling element is dramatically more efficient than the stock
unit with exit temperatures averaging 60°F cooler than stock. This delivers
cooler, denser air for increased performance throughout the RPM range.
Innovative design allows easy disassembly of cooler element & ducting for
maintenance and cleaning. Features integrated blow-off valve mount that will
accept RIVA/HKS Blow-Off Valve kit (sold separately) for improved supercharger reliability and performance. Power Cooler installs securely with shock
absorbing rubber mounting system and stainless steel hardware. Kit contains
all necessary hardware and detailed installation instructions.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
The new R&D Pro Series Racing Intercooler
Kit is constructed from aircraft aluminum and is
extremely easy to install, removes quick for
cleaning and winter storage, is ultra strong, and
rubber mounted so vibration will not compromise
the long term performance.
ENGINE/
GASKETS
The “All New” R&D Yamaha SHO/FZ/FZR Pro
Series Racing Intercooler Kit was developed
starting with a clean sheet of paper and several
key factors in mind. We wanted to build an
intercooler system that offered the easiest of
installation, easiest to maintain, looks like an
indy car part, keeps the air cooler than it looks,
and most importantly, be non restrictive to allow
maximum CFM airflow for maximum horsepower.
Part No.
612-18005
2012 IJSBA HOT PRODUCTS MARK HAHN MEMORIAL
HAVASU 300 ENDURANCE RACE IN LAKE HAVASU CITY, ARIZONA
©2012 Hot Products. All rights reserved.
41
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • INTERCOOLER
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
R&D
FX-SHO/FZR/FZS
INTERCOOLER
COOLING KIT
The R&D Yamaha FXSHO/FZR/FZS Intercooler
Temperature Control system was developed to offer
an inexpensive complete
bolt on kit that will allow the
full performance and cooling potential the O.E.M. intercooler has to offer for
recreational applications. Intercooler core water temperatures have a range of
affect on the supercharged air temperatures that enter into the engine. The
Yamaha SHO Intercooler operates on a single low pressure (10 P.S.I.) line of
lake temperature water to cool the intercooler. R&D has found that by adding
an additional intercooler water in line, and adding an additional water out line
and bypass fitting, there will be double the water flow volume at 20 P.S.I.
Reduced intercooler core temperatures can add a noticeable increase in
low end and midrange power along with reduced detonation. R&D offers a
range of machined flow control fittings to allow water volume control tuning for
intercooler temperature adjustments for warm lake water and extreme hot air
conditions. R&D also offers a pressure relief blowoff valve kit for high water
volume flow rates on higher boost Stage 1 and up engine kits. The R&D Kit
will allow temperature tuning that will deliver surprising results. Unlock hidden
performance and power potential in the OEM stock intercooler or aftermarket
intercooler system by reducing intercooler core temperatures.
• More horsepower with cooler intake air temperatures
• Increased acceleration and mid range performance
• Reduces detonation in hot weather conditions
• Temperature control tuneability
• An inexpensive recreational performance addition
• Pressure relief valve options
• Easy installation instruction
Description
R&D FX-SHO/FZR/FZS Intercooler Cooling Kit
The R&D Yamaha
FX-SHO/FZR
Engine/Intercooler
Cooling Kit was
developed for high performance recreational and racing use. Extensive
engine cooling and inlet air temperature testing using both MoTeC I2 and
Innovate digital logging systems has proven the R&D High Performance
Cooling Kit to offer double the water volume flow through the engine, oil
cooler, and intercooler as well as increase water pressure. The O.E.M. cooling
system has a very low water pressure (10 P.S.I. at 7600 rpm’s) and a low
water volume flow. The new R&D kit will double the water volume which will
lower intake air temperature by 15-20 degrees as well as lower engine block
and head temperatures by 40-50 degrees. The additional oil cooler water line
will lower engine oil temperatures by 15-20 degrees promoting better
lubrication and increased engine cooling. The R&D Cooling Kit arrives 100
percent complete with pre-cut hoses, “T” connectors, dual line pump block,
through hull bulkhead fittings, hose clamps, water by-pass fittings, the
thermostat removal sealing washer, and detailed instructions with pictures.
R&D recommends the cooling system to be upgraded as a stand alone
performance upgrade and a must have kit addition when installing power
adders such as R&D Supercharger Wheels, Engine Performance Parts, and
Engine Management Kit parts. Cooler engine, inlet air, and oil temperatures
produce higher horsepower with decrease detonation
*Better throttle response, increased horsepower
*Cooler header and under seat temperatures
*Increased power with cooler air inlet temperatures
*Cooler cylinder and cylinder head will reduce knock
*Cooler oil will lubricate better and last longer
*Increased engine protection
*Improved clutch performance with cooler oil
Description
R&D SHO/FZR Engine/Intercooler Cooling Kit
Part No.
660-18001
Part No.
660-18000
R&D FX-SHO/FZR/FZS
INTERCOOLER
TEMPERATURE
CONTROL PRESSURE
RELIEF VALVE KIT
R&D also offers a pressure relief
blowoff valve kit for high water
volume flow rates on higher boost
Stage 1 and up engine kits. The
R&D kit will allow temperature tuning
that will deliver surprising results.
Unlock hidden performance and power potential in the OEM stock intercooler
or aftermarket intercooler system by reducing intercooler core temperatures.
Description
R&D FX-SHO/FZR/FZS Intercooler
Temperature Control Pressure Relief Valve Kit
42
R&D YAMAHA
FX-SHO/FZR
ENGINE
INTERCOOLER
COOLING KIT
©2012 Hot Products. All rights reserved.
Part No.
660-82511
RIVA ENGINE BREATHER UPGRADE KIT
Easy to install Engine Breather Upgrade Kit eliminates power-robbing crankcase
emissions from your engine's air intake. Increases horsepower by removing the
engine's requirement to burn relatively non-combustible oil. Also improves
intercooler efficiency by preventing the oil sludge coating that lowers thermal
efficiency. Easy installation retains highly efficient OEM air/oil separator system.
Kit includes pre-formed hose with attached K&N filter along with all necessary
hardware & instructions.
Description
RIVA Engine Breather Upgrade Kit
Part No.
RY19040-EBUK
YAMAHA FX-SHO & FZ • INTERCOOLER
Description
SHO/FZR/FZS/VXR/VXS
BODY
RY10040-ECUK-1
Part No.
660-18004
EXHAUST
Description
Part No.
RIVA FX-SHO/FZR Stock Intercooler Upgrade Kit RY17040-ICUK
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Key Benefits Include:
• Intercooler exit temps average 30-degrees cooler than stock.
• Increased horsepower with cooler, denser air temps.
• No drilling or machining required to OEM intercooler.
• Includes billet "high-flow" pump strainer providing a second dedicated
waterline to intercooler.
• Replaceable sacrificial zinc anode protects cooling system from corrosion.
• IJSBA/ABPBA Stock Class Legal.
ENGINE/
GASKETS
The RIVA Intercooler Upgrade Kit delivers a huge performance gain to your
stock intercooler system. The cost efficient upgrade kit features billet
aluminum spacers that increase the end tank capacity and water flow in and
out of the OEM intercooler.
INATKE
SYSTEMS
RIVA FX-SHO/FZR STOCK INTERCOOLER
UPGRADE KIT
The R&D Block Thermostat Kit
Option was developed to offer a
way to run “Dual Thermostats”
to the engines cooling system
to control and allow warm up and
pre heat cycles to take place.
Engine Block and Head cooling on the Yamaha Engine becomes difficult when
running high compression ratios, higher boost levels, and aggressively
advanced ignition timing. R&D has found that multiple cooling lines need to be
added to the cooling system to provide enough volume to keep temperatures
stable and in check. The problem is the Single OEM thermostat is too restrictive and doesn’t allow enough water volume flow to reduce temperatures with
the added cooling lines. R&D has found a way to add an additional thermostat
that allows enough water flow volume to cool the engine and head and retain
the O.E.M. method for engine pre heat or warm up. The R&D Kit installs as a
bolt on kit directly in place of the corrosion anode. Running two thermostats
allows enough water flow to cool the engine properly. The R&D thermostat kit
option will start to open at 120 degrees, and will allow full flow at 140 degrees.
The O.E.M. stock thermostat opens at 118-126 degrees and allows full flow at
140 degrees. Having two thermostats installed that are full open at 140
degrees, and flow enough water volume, will help to keep engine block
temperatures to between an ideal 150-175 degrees. R&D has done extensive
testing with the engineers at MoTeC both on the Dyno and on the water to
determine that 150-160 degrees block temperatures is where the most peak
power is, any hotter and power diminishes. The R&D dual thermostat kit will be
a must have addition where engines are being run in extreme cold water and
weather conditions. There has been many debates over these theories, and
until now there has been no way around extended warm up cycles to bring
engine temps up before high engine loads can be applied. R&D has found a
way to end the debate and give everyone what they are looking for in a
complete cooling system.
YAMAHA
4 STROKE
ENGINE BLOCK
THERMOSTAT KIT
COOLING OPTION
RY10040-ECUK-PC
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
RIVA FX-SHO/FZ ENGINE COOLING
UPGRADE KITS
The RIVA Engine Cooling Upgrade Kit delivers dramatically improved cooling
efficiency to engine and oil cooler for increased reliability & performance.
Greatly enhances water flow & pressure by replacing restrictive OEM water
fittings with high-flow billet fittings and superior routing. Allows the addition of
aftermarket ECU's, high-boost compressor wheels and other performance
modifications that can increase heat & detonation. Includes all necessary
water lines, hardware, fittings and detailed installation instructions.
Fits 2009-10 FX-SHO & FZ models.
Description
Part No.
FX-SHO/FZ Engine Cooling Upgrade Kit
RY10040-ECUK-1
For use with the OEM Intercooler Upgrade Kit
FX-SHO/FZ Engine Cooling Upgrade Kit
RY10040-ECUK-PC
For use with the RIVA Power Cooler Kit
©2012 Hot Products. All rights reserved.
43
YAMAHA FX-SHO/FZ/VXR/VXS • EXHAUST
YAMAHA
4 STROKE
BILLET EXHAUST
OUTLET
The new R&D Billet Exhaust
Outlet.
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
Description
R&D 3" Diameter Billet Exhaust Outlet
R&D 2.75" Diameter Billet Exhaust Outlet
44
RIVA REAR EXHAUST KIT
RIVA Racing Rear Exhaust Kit delivers performance and cutting-edge style.
Allows for removal of restrictive sound suppression system located between
waterbox and hull exit. Improves engine performance by reducing back
pressure and restriction. Includes mandrel bent aluminum exhaust tube that
is powder coated to prevent corrosion, large billet through-hull exhaust outlet,
billet OEM exhaust outlet block-off and high-temp silicone couplers along
with all necessary mounting hardware & installation.
Description
RIVA Racing FZR/FZS Rear Exhaust Kit
RIVA Racing FX-SHO Rear Exhaust Kit
RIVA Racing VXR/VXS Rear Exhaust Kit
Part No.
RY15050
RY15040
RY15060
Part No.
331-30000
331-32750
R&D HIGH
TEMPERATURE
SILICONE COUPLINGS
Description
3" - 3" High Temp Silicone Couplings
3" - 2" Reducer High Temp Silicone Couplings
2.75" - 2.5" Reducer High Temp Silicone Couplings
3" - 2.75" Reducer High Temp Silicone Couplings
Part No.
061-30030
061-32500
061-32501
061-32750
EXHAUST RESONATOR
REMOVAL KIT
The R&D Exhaust Resonator Removal Kit will allow the
sound suppression ball to be removed and plugged.
When removing the exhaust sound suppression ball and
modifying the exhaust hose, low end response is gained
and trapped hot exhaust gases can be evacuated quicker through less
restriction or back pressure.
RIVA FX SHO/FZR FREE FLOW EXHAUST KIT
Description
R&D VXR/VXS Exhaust Resonator Removal Kit
Part No.
332-18005
Replaces the restrictive sound suppression system located between the water
box and hull exit on your watercraft. Improves engine performance by reducing
back pressure and harmful detonation. Includes mandrel bent aluminum tubing
that is powder coated to prevent corrosion, high-temp silicone replacement
coupler and installation instructions.
Description
RIVA FX-SHO/FZR/FZS Free Flow Exhaust Kit
A.
Part No.
RY16040
RIVA FX-SHO/FZ PRO-SERIES WATER BOX
B.
R&D FX-SHO/FZR/FZS
HIGH FLOW EXHAUST KIT
The R&D SHO High Flow Exhaust Kit will add a noticeable low end and mid
range power feel as well as add top end performance! The R&D High Flow
Exhaust Kit will add a great performance sound to the SHO while maintaining
a safe and under IJSBA and Coast Guard approved 86 db!
Description
A. RIVA FX-SHO/FZR/FZS High Flow Exhaust Kit
B. RIVA VXR/VXS Free Flow Exhaust Kit
©2012 Hot Products. All rights reserved.
Part No.
332-18000
RY16060
Developed on RIVA’s Dyno and tested extensively on the water, this water box
features radiused exhaust tubes and end caps for optimum exhaust flow.
Unique exhaust baffle will increase the low-end power and mid-range pull of
your Yamaha watercraft. Delivers up to 15hp on modified engines along with
significant torque gains. High-strength aluminum construction will survive
backfires and meltdowns. Powder coated to prevent corrosion.
A must for modified motors.
Key Features:
• Delivers up to 15hp on modified craft!
• Machined hose flanges for reliable coupler retention.
• Radiused exhaust tubes & end caps.
• Powder coated to prevent corrosion.
Description
RIVA FX-SHO/FZ Pro Series Water Box
Part No.
RY16041
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE • FUEL SYSTEM
Description
RIVA Fuel Pressure Regulator Kit
Part No.
RY12040-RRFPR-6S5
Description
R&D FX-SHO/FZR/FZS/VXR/VXS In-Tank Fuel
Pressure Regulator Block Off Kit
Part No.
812-35257
The R&D Fuel Pressure
Gauge Adapter Tool is
designed to be a plug in
fuel pressure gauge that needs no modifications to install and use. Simply
disconnect the OEM locking fuel connector from the fuel rail and plug the
gauge tool directly into the connector. Plug the locking connector supplied on
the R&D tool onto the fuel rail and lock. Use the tool to verify fuel pressure
and fuel pump condition. Use the tool to set and verify base fuel pressure
settings on the R&D Rising Rate Fuel Pressure Regulator (RRFPR). When
finished, disconnect the tool and reconnect the stock fuel line. The Adapter
installs inline between the OEM fuel rail and the R&D RRFPR via the OEM
connectors for easy connect and disconnect. The R&D Tool works on both
Yamaha and Kawasaki fuel systems. Installation time is only 2 minutes.
Liquid filled fuel pressure gauge sold separately.
Description
R&D Inline Fuel Pressure Gauge Adapter
R&D Liquid Filled Fuel Pressure Gauge
Part No.
612-00081
900-02180
©2012 Hot Products. All rights reserved.
BODY
R&D offers a Fuel Pressure Regulator Block off
Kit which will allow the OEM stock in tank fuel
pressure regulator to be removed, blocked off,
and replaced with a billet part which is mandatory when installing an
aftermarket externally adjustable fuel pressure regulator system. The OEM
in tank fuel pressure regulator is fixed to maintain 40-43 pounds of fuel
pressure at all times. For high performance applications where horsepower is
boosted, it is necessary to install larger flowing fuel injectors and be able to
tune the fuel pressure up or down as needed. Most factory race teams are
running 65 plus pounds of fuel pressure along with higher flowing fuel
injectors and externally adjustable pressure regulators. The R&D has a
complete line up of fuel pumps, fuel injectors, fuel pressure regulators, fuel
gauge, and fuel hose accessories all designed specifically for the Yamaha
SHO. All R&D fuel injection parts and products meet Coast Guard, I.J.S.B.A.,
and APBA approval.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D INLINE
FUEL
PRESSURE
GAUGE
ADAPTER
R&D-FX SHO/FZR/VXR/VXS
IN-TANK FUEL PRESSURE
REGULATOR BLOCK OFF KIT
EXHAUST
801-25010
Fits Yamaha FX-SHO, FZR & FZS models.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Part No.
802-00080
Key Features Include:
• Precision fuel pressure control with optional rising rate function.
• High quality stainless steel liquid-filled pressure gage.
• Large 3/8” fuel return line.
• Includes billet Fuel Pressure Regulator Block-Off.
• Easy bolt-on installation with OEM fuel connectors.
• Includes complete installation instructions & tuning guide.
ENGINE/
GASKETS
Description
R&D FX-SHO/FZR/FZS/VXR/VXS
Fuel Pressure Regulator Kit (Shown above)
R&D Fuel Pressure Regulator
(Fittings not included)
RIVA Fuel Pressure
Regulator Kit provides
the precision pressure
control necessary to
compliment aftermarket
ECU applications on the
'SHO' engine. Kit is fully
assembled & mounts
securely on top of fuel tank
via sturdy aluminum
bracket. High quality billet
pressure regulator can
adjust base pressure from
25 to 80 PSI. Unit can also
be set up as rising rate fuel pressure regulator at a 1 to 1 ratio providing one
additional pound of fuel pressure for every pound of boost gain. Plugs directly
into original fuel system with OEM connectors and features a large 3/8" fuel
return line that is routed through supplied rubber fuel tank cap. Includes
integrated liquid-filled pressure gauge and billet Fuel Pressure Regulator
Block-Off necessary for removal of stock fuel pressure regulator in fuel tank.
INATKE
SYSTEMS
R&D offers a Yamaha FX-SHO/FZR/FZS
model specific fuel pressure regulator
system allowing custom fuel pressure tuning to the EFI fuel systems fuel pressures. The R&D Fuel Pressure Regulator System offers a wide range of setup
possibilities. Base fuel pressure is adjustable from 5 to 60 PSI. The R&D fuel
pressure regulator can also be set up to allow “rising rate” fuel pressure at a
1 to 1 ratio (One pound of fuel pressure gain over base for every pound of
boost gain). R&D offers two types of fuel pressure regulator set ups. Part
#802-00080 will come completely assembled and ready to install. The R&D
Pro System is 100 percent complete, installs directly to the top of the fuel
tank, and connects directly to the fuel rail with OEM security lock connectors
with no modifications. For the R&D Fuel Pressure Regulator only use part
#801-25010, which comes complete with 90 degree barbed brass fittings for
use with push on type hose and Oetiker style clamps for security. R&D offers
high performance fuel hose that can be purchased by the foot, as well as the
Oetiker style clamps. The R&D bypass style regulator system is capable of
handling any fuel pump up to 250 GPH. Replace “Deadhead” regulator
performance and experience the full flow volume and rock steady fuel
pressure that only a dynamic R&D fuel pressure regulator kit can produce.
•
Fuel pressure will rise on a 1:1 ratio when boost referenced
•
All ports are 3/8” NPT, with one inlet, 3 outlets, and one return
port on the bottom
•
Beautiful type II bright dip anodized finish
•
Bypass design produces the ultimate, dynamic fuel delivery system
•
3/8” pipe tapped for standard or AN fitting ready
•
R&D offers pre-assembled #4 AN hose to finish off a return system
•
R&D offers fuel hose by the foot for custom routing
RIVA FX-SHO/FZ
RISING RATE
FUEL PRESSURE
REGULATOR KIT
YAMAHA
4 STROKE
R&D FXSHO/FZR/FZS/VXR/VXS
FUEL PRESSURE
REGULATOR KIT
45
RIVA FX-SHO/FZ
BOOST CLAMP
RIVA’s Boost Clamp will allow you to
run up to 17psi of boost pressure in
your Yamaha SHO engine when used with RIVA Fuel Pressure Regulator Kit
and stock ECU. Device controls communication between stock MAP sensor
and stock ECU to allow for higher boost levels and more power. The Boost
Clamp is an integral part of RIVA Stage 2 SHO Engine Kit producing 260hp
when combined with our recommended components. Installs quickly & easily
with integrated waterproof connectors.
Description
RIVA FX-SHO and FZ Boost Clamp
The R&D Yamaha FZR/SHO Multi-Pressure Port Adaptor Kit will allow quick and
easy hook up of a manual boost gauge, surge valve, and a raising rate fuel
pressure regulator. The R&D Pressure Port Adaptor installs in the MAP sensor
hose and has 3 ports that allow for the operation of a vacuum/boost gauge, check
plenum air temperatures, operate a surge protection valve, and operate a boost
referenced fuel pressure regulator (RRFRP), or any three of these applications at
the same time with one simple part. The R&D Pressure Port Adaptor Kit comes
complete with 12” of vacuum hose, multi-line fitting, 2 tube covers, nylon cable ties
and instructions.
Description
R&D 2011 FZR Multi-Pressure Port Boost Gauge
Surge - RRFPR Adaptor Kit
Part No.
612-92006
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
This is a direct replacement high volume fuel pump for high performance
applications. Delivers 265LPH to support highly modified engine packages.
Easy installation requires no modifications. Includes detailed installation
instructions.
Description
RIVA/HKS FX-SHO High Volume
Fuel Pump
Part No.
RY12040-265FP-6S5
R&D FX-SHO/FZR/FZS/VXR/VXS
HIGH PERFORMANCE
HIGH VOLUME FUEL PUMP KITS
R&D Performance carries a complete line up of high performance
replacement fuel pumps that are machined specifically to fit the Yamaha
FX-SHO/FZR/FZS fuel pump housing and are offered in a variety of flow
ratings to facilitate from basic low cost replacement to an all out 500 H.P.
race machine. All R&D FX-SHO/FZR/FZS fuel pumps have been precision
flow rate tested and charted in (LPH) liters per hour. R&D FX-SHO/FZR/FZS
fuel pumps arrive complete with Yamaha FX-SHO/FZR/FZS model specific
installation instructions complete with detailed photos that will help make the
fuel pump installation quick and easy.
NOTE: There are no modifications necessary to install the R&D fuel pump
therefore switching back to the O.E.M. fuel pump assembly is quick and easy
as well.
Part No.
812-35190
812-35255
812-35256
R&D FX-SHO/FZR/FZS
MULTI-PRESSURE PORT BOOST
GAUGE/SURGE/RRFPS ADAPTER KIT
The R&D Yamaha FX-SHO/FZR/FZS Multi-Pressure Port Adapter Kit will
allow quick and easy hook up of digital or manual boost gauges with the
R&D Multi-port billet Adapter. The R&D Pressure Port Adapter installs
between the MAP sensor and the MAP sensor bracket as a “bolt on” part
no with modifications. Operate a vacuum/boost gauge, check plenum air
temperatures, and operate a surge protection valve at the same time, or run
a boost gauge, surge protection device, and operate a boost referenced fuel
pressure regulator (RRFPR) at the same time with one simple part. The R&D
Pressure Port Adapter Kit comes complete with longer MAP sensor mounting
screws, o-ring seals, nylon cable ties, all mounting hardware and instruction.
Description
R&D FX-SHO/FZR/FZS Multi-Pressure Port Boost
Gauge/Surge/RRFPS Adapter Kit
46
RIVA/HKS FX-SHO/FZ
HIGH VOLUME FUEL PUMP
Description
R&D FX-SHO/FZR/FZS/VXR/VXS 190 LPH
OEM Replacement Fuel Pump Kit
R&D FX-SHO/FZR/FZS/VXR/VXS 255 LPH
Low Pressure Fuel Pump Kit
R&D FX-SHO/FZR/FZS/VXR/VXS 255 LPH
High Pressure Fuel Pump Kit
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
Part No.
RY11740-BC-6S5
R&D 2011 FZR
MULTI-PRESSURE
PORT BOOST GUAGE
SURGE - RRFPR
ADAPTOR KIT
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • FUEL
©2012 Hot Products. All rights reserved.
Part No.
612-92005
R&D #4 & #6 FUEL RETURN LINE KIT
R&D has developed a two larger fuel return line kits for the FX-SHO/FZR/FZS.
Increasing the diameter of the fuel return line to #4 or #6, decreases line
pressure and increases fuel volume, yielding increased tuning ability in high
heat and higher performance applications.
Description
R&D #4 Fuel Return Line
R&D #6 Fuel Return Line
Part No.
612-00082
612-00083
YAMAHA FX-SHO/FZ/VXR/VXS • FUEL
RIVA FX SHO/FZ
3 BAR MAP
SENSOR KIT
Do you plan on running over
14.7psi of boost? If so, our
3 Bar MAP Sensor Kit is
essential for accurate engine
management with high
boost applications. High
quality 3 Bar MAP Sensor
will measure up to 29.7psi,
where the OEM 2 Bar MAP Sensor will only measure up to 14.7psi. It is
critical to provide accurate pressure information to your aftermarket ECU to
ensure proper air/fuel mixture and data logging. RIVA 3 Bar MAP Sensor
mounts directly in place of OEM sensor with stainless bracket and plugs
directly into OEM wiring harness.
Part No.
RY11740-MS-3
Part No.
332-18010
R&D O2 SENSOR WRENCH
The R&D O2 Sensor wrench is custom designed with crows feet ends to
allow easy installation or removal of the Oxygen sensor.
Description
R&D O2 Sensor Wrench
Part No.
332-18011
BODY
Description
RIVA FX-SHO/FZ 3 Bar Map Sensor Kit
EXHAUST
Description
FX-SHO/FZR/FZS/FX140/HO/GPR/VX110/VXR/VXS
O2 Sensor Mount Kit
Part No.
RY12040-I-KIT-100
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
The new R&D O2 sensor mount
kit makes installing an AFR gauge
a breeze on the Yamaha FX-SHO,
FZR, FZS, FX140, HO, GPR, and
VX110. It simply replaces the
OEM plug and installs directly into
the OEM pipe without any modifications. Kit comes complete with installation
tool. AFR gauge sold separately.
Description
RIVA Pro-Series Yamaha Fuel Injectors
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
R&D
FX-SHO/FZR/FZS
O2 SENSOR
MOUNT KIT
RIVA PRO-SERIES YAMAHA FUEL INJECTORS
Our high impedance fuel injector kit delivers additional fuel to modified
engines for high boost applications. 100lb (1,000cc) injectors are for use with
aftermarket ECU (RY11840-01-C) for correct calibration. Kit includes injectors,
plug and play adapters, fuel rail spacers and detailed installation instructions.
Fits 2009-12 FX-SHO & FZ models.
ENGINE/
GASKETS
Description
Part No.
R&D Pro-Series 725cc Injectors (set of 4)
812-18001
Flow Rate: 725cc at 43.5 Pounds of Pressure =72 Pounds Per
Fuel Hour Fuel Flow.
Flow Rate: 925cc at 70.0 Pounds of Pressure =92 Pounds Per
Fuel Hour Fuel Flow.
R&D Pro-Series 1000cc Injectors (set of 4)
812-18002
Flow Rate: 1000cc at 43.5 Pounds of Pressure =100 Pounds
Per Fuel Hour Fuel Flow.
Flow Rate: 1225cc at 70.0 Pounds of Pressure =120 Pounds
Per Fuel Hour Fuel Flow.
INATKE
SYSTEMS
R&D Pro Series injectors offer increased fuel
delivery over our 525cc injectors. The new Pro
Series injectors are offered in 725cc and
1000cc flow rates. Each set of injectors have been flow rate and voltage
comp tested to insure linear accuracy and are shipped with a precision dead
time (voltage compensation) chart that can be added into your aftermarket
ECU’s software program under battery compensations. R&D Pro Series
injectors offer perfectly clean linear response performance from low idle all
the way through the entire power range. R&D has flow rate tested the O.E.M.
Yamaha FX HO injectors and verified them to flow 396 cc at 43 PSI of fuel
pressure, which rates them to flow 39 pounds of fuel per hour. The R&D Pro
Series Fuel Injectors have been precision flow rate tested to 725cc at 43 PSI
of fuel pressure, and 925cc at 70 PSI of fuel pressure, which rates them to
flow as much as 92 pounds of fuel per hour. R&D fuel injectors perform
excellent, delivering precise fuel flow at fuel pressure ratings ranging from 40
to 80 PSI. Each R&D injector set is packaged complete with all installation
hardware, necessary harness interface connectors, voltage compensation
chart, and instructions.
YAMAHA
4 STROKE
FX-SHO/FZ/VXR/VXS 725
CC/1000 CC PRO SERIES
FUEL INJECTOR KIT
2012 IJSBA HOT PRODUCTS MARK HAHN MEMORIAL
HAVASU 300 ENDURANCE RACE IN LAKE HAVASU CITY, ARIZONA
©2012 Hot Products. All rights reserved.
47
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
FX-SHO/FZR HIGH PERFORMANCE R&D ECU REPROGRAMMING SERVICES
DOLLAR FOR DOLLAR UNBEATABLE PERFORMANCE: R&D is proud to announce our new line up of Yamaha FZR and SHO ECU reprogramming services.
The engineering staff at R&D have been testing and developing ECU programs to allow new performance levels to be reached for recreational enthusiasts and
racers who are interested in more performance through reprogrammed the OEM ECU. Entry level programs will allow the enjoyment of a raised RPM limit settings,
advanced ignition timing, re-calibrated fuel map, as well as the internal boost limiter raised to allow R&D Monster Wheels to work to full potentials. There are
several performance levels to choose from that work with stock or R&D C1, C3, and C5 Monster Wheels or any wheel kit rated up to 18 pounds of boost. Programs
offered are recreational performance tuned with safe AFR values, and can be further custom tuned (Richened) to accommodate additional boost levels. Existing
customers who have purchased an R&D Powershot Fuel Control Unit can send their units in to R&D for free upgraded re-programming to allow custom fuel tuning
to work with the new ECU Programs. R&D Powershot Fuel Control Units are not required on entry recreational level (R1, R2, or R3) programs using stock, C1,
or C3 Wheels. However, custom fuel tuning with the Powershot Fuel Tuner can be an add-on or additional upgrade that is suggested for higher performance
applications such as C5 Monster Wheel Kits. Fuel tuning or AFR conditions should always be checked and verified as values will always be slightly different from
one engine set up to another. Higher performing programs are continuously under development and will be announced through updates on the R&D website, so
stay tuned. Custom program files can also be performed to accommodate just about any combination of performance level or type of fuel being used. R&D strongly
suggests that AFR tuning be periodically verified using Innovate Products LM1 or LC1 Logging Kit also available from R&D.
Part #802-01801 R&D R1 ECU; Reprogrammed ECU to allow up to 8450 RPM’s, Raised Boost limiter to allow up to 18 pounds boost, and upgraded ignition timing
safe for all recreational and offshore racing use. R1 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18 pounds of boost. 89
octane safe with stock and C1 wheels, 91 octane pump fuel use is recommended for C3 and C5. The R1 program file does not require a Powershot Fuel Tuner for
use with C1 and C3 Monster Wheels.
Part #802-01802 R&D R2 ECU; Reprogrammed ECU to allow 8750 RPM’s, Raised Boost limiter to 17 pounds, advanced ignition timing for high performance
recreational use. R2 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18 pounds of boost. 91 octane pump fuel should be
used with R2 reprogram. 93-95 octane fuel is recommended for closed course racing conditions where high engine loads are present. The R2 program file does
not require a Powershot Fuel Tuner for use with C1 and C3 Monster Wheels.
Part #802-01803 R&D R3 ECU; Reprogrammed ECU to allow 8850 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing in the low end areas
and softer high rpm settings in the peak boost areas for high performance recreational use. R3 works great with C1, C3, or C5 Monster Wheel Kits, or any wheel
kit rated up to 18 pounds of boost. 91-93 octane pump fuel should be used with R3 reprogram with O.E.M. 8.6-1 pistons and cams. R&D suggests 100 plus octane
fuel when using 9.5-1 pistons, RC1 Cams, and R&D Pro Tune Adjustable Cam Gear Kits. NOTE: The R3 program file does not require a Powershot Fuel Tuner for
use with C1 and C3 Monster Wheels. Use the Powershot for custom fuel tuning with C5 wheel kits. NOTE: The R&D RRFPR Kit is required when using the R&D
C5 Monster Wheel Kit.
Part #802-01803V R&D R3 VF ECU; Reprogrammed ECU allows the use of variable fuels. Run 91 octane at 12-13 pounds (180 kpa) of peak boost, and run 98
or 100LL Aviation fuel when boost pressure is adjusted to 15-18 pounds. The program allows 8850 RPM’s, eliminated Boost limiter, aggressively advanced ignition
timing in the low end areas and softer high rpm settings in the peak boost areas for high performance recreational use. R3 VF works great with C1, C3, or C5
Monster Wheel Kits, or any wheel kit rated up to 18 pounds of boost. 91-93 octane pump fuel should be used with R3 VF reprogram with O.E.M. 8.6-1 pistons and
cams at 12-13 pounds. R&D suggests 100 plus octane fuel when using 9.5-1 pistons, RC1 Cams, and R&D Pro Tune Adjustable Cam Gear Kits. NOTE: The R3 VF
program file does not require a Powershot Fuel Tuner for use with C1 and C3 Monster Wheels. Use the Powershot for custom fuel tuning with C5 wheel kits. NOTE:
The R&D RRFPR Kit is required when using the R&D C5 Monster Wheel Kit. NOTE: Adjusting the peak boost pressure is done via the R&D/GReddy adjustable
boost level/surge protection valve. The R3 VF Program allows the recreational rider/racer the flexibility to race on Sunday with 15-18 pounds of boost and
aggressive timing with 100 octane Aviation fuel, and still be able to take the family out for weekend fun with 91 octane pump gas when boost is adjusted back to
10-13 pounds. NO need for switching booster wheels to attain lower boost and lower rpm settings. Another great feature available only from R&D!
Part #802-01804 R&D R4 ECU; Reprogrammed ECU to allow 8850 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires 100 octane
Aviation fuel for high performance Pro Stock or Pro Limited racing use. R4 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to
18 pounds of boost.
Part #802-01805 R&D R5 ECU; Reprogrammed ECU to allow 8950 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires VP MS 109
race gas for high performance Pro Stock or Pro Limited racing use. R5 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18
pounds of boost.
Part #802-01806 R&D R6 ECU; Reprogrammed ECU to allow 9000 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires VP MS
109E fuel for high performance Pro Stock or Pro Limited racing use. R6 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18
pounds of boost.
Part #802-01807 R&D R7 ECU; Reprogrammed ECU to allow 9000 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires VP C12
race gas for high performance Pro Stock or Pro Limited racing use. R7 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18
pounds of boost.
Part #802-01808 R&D R8 ECU; Reprogrammed ECU for 725cc injectors @ 52 psi fuel pressure, 8750 RPM’s, eliminated Boost limiter, advanced ignition timing
requires 91 octane pump gas for high performance recreational use. R8 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Part #802-01809 R&D R9 ECU; Reprogrammed ECU for 725cc injectors @ 52 psi fuel pressure, 8850 RPM’s, eliminated Boost limiter, advanced ignition timing
requires 100 octane Aviation fuel. R9 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Part #802-01810 R&D R10 ECU; Reprogrammed ECU for 725cc injectors @ 52 psi fuel pressure, 9000 RPM’s, eliminated Boost limiter, advanced ignition timing
requires VP MS 109 Race gas. R10 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Part #802-01811 R&D R11 ECU; Reprogrammed ECU for 725cc injectors @ 60 psi fuel pressure, 9000 RPM’s, eliminated Boost limiter, advanced ignition timing
requires VP C12 Race gas. R11 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Part #802-01812 R&D R12 ECU; Reprogrammed ECU for 1000cc injectors @ 60 psi fuel pressure, 9000 RPM’s, eliminated Boost limiter, advanced ignition timing
requires VP MS 109/C12 Race gas. R12 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
NOTE: Rev Limiter settings can be raised or lowered upon request.
48
©2012 Hot Products. All rights reserved.
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D YAMAHA VXR/VXS
POWERSHOT
ADJUSTABLE FUEL TUNER
Part No.
802-18000
Description
Part No.
R&D VXR/VXS Powershot Adjustable Fuel Tuner
802-18010
EXHAUST
R&D SHO/FZ/FZR Powershot Adjustable Fuel Tuner
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
• Preprogrammed and Pre set to 12.5:1 (plug in and run)
• Allows overall fuel map tuning
• Utilizes O.E.M. ignition system
• Utilizes O.E.M. fuel injectors
• Retains all O.E.M. dash, warning, and service indicators
• 91 octane pump gas friendly
• Ultra easy 20 minute installation
For competition use only!
ENGINE/
GASKETS
The R&D Powershot is fully adjustable to accommodate and properly
performance tune the A.F.R. for any combination of aftermarket parts.
No more Boost Limiter!
R&D Powershot Fuel Injection/Engine Tuning module
for the Yamaha VXR/VXS. The R&D Powershot will
deliver increased acceleration, stronger mid-range,
and increased top speed performance by delivering
a higher performing air to fuel ratio (A.F.R.) R&D
Performance has data logged and analyzed the
O.E.M. fuel map on the Yamaha 1.8 N/A four stroke
engine and documented that the fuel tables are a very green and
stoichiometric. If quicker acceleration and stronger mid range power and the
ability to have your cake and eat it too, then the Powershot is for you. The
Powershot will allow you to adjust the fuel to either run green or mean. The
R&D Powershot interfaces with the stock E.C.U., and fuel injectors allowing
piggy back adjustments to the fuel table. The R&D Powershot comes
pre-programmed and coded to safely alter the fuel map right out of the box
for plug and play performance. The R&D Powershot allows custom fuel tuning
to cruise, acceleration, and top end zones. Top end fuel mixtures can be
custom tuned from 13.5:1 (lean) to 11.5:1 (rich) on the fly. Quicker
acceleration, stronger mid-range, and increased top speed performance is the
result when the A.F.R. is tuned for optimum performance. The R&D Powershot
is fully adjustable to accommodate and properly performance tune the A.F.R.
for any combination of aftermarket parts. Unlock the Yamaha VXR/VXS’s full
performance potential with an R&D Powershot Engine Tuner.
INATKE
SYSTEMS
The new R&D Powershot Fuel Injection/Engine
Tuning module for the YAMAHA SHO/FZR will
deliver increased acceleration, stronger mid-range,
and increased top speed performance by delivering
a higher performing air to fuel ratio (A.F.R.) and
allowing higher mass air/boost pressure levels to be
utilized. R&D Performance has data logged and
analyzed the O.E.M. fuel map and Fly By Wire functions on the new Yamaha
SHO/FZR four stroke engine and has determined that one of the main horsepower and performance holdbacks in Yamaha’s Fly by Wire E.C.U. system is
the mass air or boost limitation that is controlled by the Fly by Wire Throttle
System. The Yamaha E.C.U. manipulates and controls the mass air or boost
pressure levels by closing the throttle plate which limits peak horsepower
performance. The R&D Powershot interfaces with the E.C.U., fuel injectors,
and sensors to unlock, take over, and control mass air or boost limitations.
The R&D Powershot will allow the R&D C1 and C3 Monster Supercharger
Wheels to perform to their full potential by defending against unwanted codes
and internal E.C.U. limitations. The R&D Powershot comes pre-programmed
and coded to safely alter the fuel map, intercept and recondition sensor
voltage signals allowing up to 10 P.S.I. of boost pressure without throttle
limitation or regulation. The R&D Powershot allows custom fuel tuning to
cruise, acceleration, and top end zones. Top end fuel mixtures can be custom
tuned from 13.5:1 (lean) to 11.5:1 (rich) on the fly. Quicker acceleration,
stronger mid-range, and increased top speed performance is the result when
the A.F.R. is tuned for optimum performance.
YAMAHA
4 STROKE
R&D YAMAHA SHO/FZ/FZR
POWERSHOT ADJUSTABLE
FUEL TUNER
BODY
Part #802-02801 R&D R1 ECU; Reprogrammed ECU for the VXR/VXS
offers improved ignition timing map advancements that produce quicker
acceleration and top speed performance. The fuel maps are tuned to offer a
cleaner than stock (leaner idle), clean and green cruise areas which will
keep fuel consumption either the same or better than stock in the cruising
ranges, and an overall improvement to top speed or wide open throttle
ranges. The rev limiter is raised to allow up to 8150 RPM’s that will promote
a more positive pump hook up in rough water conditions. The R1 ECU
programs are 89 and 91octane (pump fuel) safe. The R1 program file does
not require a Powershot Fuel Tuner.
Description
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
VXR/VXS HIGH PERFORMANCE ECU
REPROGRAMMING SERVICES
Part #802-02802 R&D R2 ECU; Reprogrammed ECU for the VXR/VXS
offers improved ignition timing map advancements that produce quicker
acceleration and top speed performance. The fuel maps are tuned to offer
a cleaner than stock (leaner idle), clean and green cruise areas which will
keep fuel consumption either the same or better than stock in the cruising
ranges, improved hard acceleration enrichment for the hard core rider that
want a more aggressive mid range acceleration, and an overall improvement
to top speed or wide open throttle ranges. The rev limiter is raised to allow up
to 8250 RPM’s that will promote a more positive pump hook up in rough
water conditions. The R2 ECU programs are 91octane (pump fuel) safe. The
R2 ECU program can be used with R&D Performer, Stage 1 and 2 kits. The
R2 program file does not require a Powershot Fuel Tuner.
NOTE: Custom Rev Limiter settings available upon request.
Part No.
R&D Reprogrammed R1 ECU for the VXR/VXS
R&D Reprogrammed R2 ECU for the VXR/VXS
802-02801
802-02802
©2012 Hot Products. All rights reserved.
49
The RIVA/ATHENA Pro-Series ECU provides
a huge performance advantage to the Yamaha
1.8L Engine delivering over 50hp to the stock
SHO engine. ECU is fully programmable with
either RIVA supplied mapping or user
adjustable parameters. Most calibrations require use 91+ octane pump fuel.
Plugs directly into factory wiring harness via waterproof connectors.
Key Features Include:
1. Easy loading of supplied calibrations/maps for various performance
applications.
• Performance Fuel Mapping: Delivers optimal fuel required for your
specific level of modification based on boost pressure.
• Performance Timing Curves: Special racing curves produce more power
throughout the RPM range.
• Rev Limiter Increase: Stock rev limit can been increased so engine RPM
can be run higher producing more boost pressure and horsepower.
• Boost Control for turbo applications. (Plug & play connector for
wastegate solenoid).
2. Retains all OEM dash display functions & Engine Safety Functions.
3. Provides diagnostic information that can be displayed via computer
interface.
4. Includes plug & play connector for RIVA Dash/Logger unit
(RY11840-LD-MD60).
5. Includes plug & play connector for optional lambda sensor kit
(part# RY11540-LC1-6S5) for data logging air/fuel ratios & tuning functions.
6. Individual Cylinder Knock Control function protects engine. System
identifies which cylinder is detonating by tracking firing order utilizing
OEM knock sensor.
7. User selectable dual calibration capacity.
NOTE: RIVA Pro-Series ECU is for competition use only.
Description
RIVA/Athena Pro-Series ECU
Part No.
RY11841-ECU-HFPWC
Our new RIVA/ATHENA Dash Logger allows
you to monitor and log all critical engine
functions along with internal GPS driven
speed data. This completely waterproof unit
plugs directly into RIVA/ATHENA ECU’s and is
compact enough to mount on handlebar
cross-bar via optional mounting pad. Large
easy-to-read backlit display provides data on
user friendly selectable screens. All displayed
engine & GPS data is logged for review
through convenient computer download via
USB port. GPS Track mapping function displays “live” lap times and related
functions for buoy course training purposes. Features LED warning lights to
notify operator of major engine concerns.
Key Features Include:
• Large easy-to-read backlit screen.
• Compact design allows handlebar mount with optional mounting pad.
• Rugged waterproof construction.
• Built in GPS provides speed & position info.
• Plugs directly into RIVA/ATHENA ECU with waterproof connector.
• Operates in unison with factory dash display.
• Selectable display modes include 3 user definable pages for custom
data display.
• Easy to download “data file” allows review of engine functions & GPS data.
• Logger memory holds last 60 minutes of operation.
• Displays & logs the following data:
• Displays & logs MIN/MAX values of all data.
• GPS Track mapping displays & logs lap times.
• LED warning lights notify operator of engine concerns.
Description
RIVA/Athena Dash Logger
For RIVA/Athena Pro-Series ECU
Part No.
RY11840-LD-MD60
ELME TOOLS SEVED PRO HARDWARE
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
• Portable and autonomous, it does not need to be plugged to any
other machine
• No PC or power connector is needed to service the PWC
• Key Programming
• Full Specialized technical support
Program updates are received via the internet. The dongle system allows
this, and cables and dongles are included with each program. Program
updates are free.
Picture is for reference only. Colors may vary.
50
RIVA/ATHENA
DASH LOGGER
RIVA/ATHENA
PRO-SERIES ECU
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
©2012 Hot Products. All rights reserved.
Description
Part No.
Seved Pro Hardware Base Unit
SEVED PRO
BRP Diagnostics Program
ADS400
BRP Key Programming
ADS401
Kawasaki Diagnostic Program
ADS402
Mercruiser Diagnostic Program
ADS403
Yamaha Diagnostic Program
ADS404
Hydrospace/Benelli
ADS405
Seved Pro Hardware Base Unit
PWCPAK
+ADS400+ADS401+ADS402+ADS404+ADS405 (excludes ADS403)
Seved Pro Hardware Base Unit
FULLPAK
+ADS400+ADS401+ADS402+ADS403+ADS404+ADS405
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
Description
Part No.
RIVA/DARTON YAMAHA
1.8L PRO-SERIES
CYLINDER SLEEVES
CP PISTON KITS FOR YAMAHA FX SHO
(2009-2011)
PISTON
KIT
M1077
M1078
M1081
DESCRIPTION
86mm Standard Bore (1812cc)
2009 - 11 Yamaha FX SHO 8.6:1 Turbo
86mm Standard Bore (1812cc)
2009 - 11 Yamaha FX SHO 9.5:1 Turbo
86mm Standard Bore (1812cc)
2009 - 11 Yamaha FX SHO 10.5:1 Turbo
Oversize Pistons
M1082
CPN-3386
CPN-3386
CPN-3406
CPN-3406
CPN-3406
RIVA’s new bulletproof sleeve system is the
ultimate foundation for your high performance
engine. Engineered specifically for the
Yamaha SHO engine by Darton Sleeves, the
leader in racing sleeve technology, these
sleeves will hold up to extreme punishment in
high boost applications. Innovative “Flat-Lock”
flange design locks sleeves in place reinforcing block and protecting head
gasket.
Key Features Include:
• Integrated Flat-Lock flange design protects block.
• Bulletproof Darton ductile steel construction.
• Increased horsepower potential.
• Ideal for high boost supercharged & turbo applications.
• Superior ring sealing.
• Can be installed by your local machine shop.
Part No.
RIVA/Darton Yamaha 1.8L Pro-Series
Cylinder Sleeves (Sold 4 sleeves per set)
WISECO PISTON KITS FOR YAMAHA
Yamaha
Model
Years
Bore x
Stroke (mm)
Piston Kit
Number
Replacement Pins &
Ring Set
Clips
2008-10
86.00
40049M08600
8600XX
FX Cruiser HO
FX SHO
2008-10
x
FZR
2009-10
78
FZS
2009-10
Displacement 1812.7cc • 8.6:1 Compression Supercharged
11.1 Compression Non-supercharged • ArmorGlideTM Skirt Coated
Piston sold complete with: rings, piston pin and circlips.
Wrist Pin
S734
Circlips
W5590
RY10040-SLV-470
NGK SPECIAL
SPARK PLUGS
FOR FOUR
STROKE ENGINES
Description
Yamaha FX SHO/FX Cruiser,
SHO/FZR (10 plugs per box) Solid Tip Plug
Part No.
LFR6A
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Description
BODY
86.5mm .5mm oversize (1834cc)
2009 - 11 Yamaha FX SHO 8.6:1 Turbo
M1083
86.5mm .5mm oversize (1834cc)
2009 - 11 Yamaha FX SHO 9.5:1 Turbo
M1084
86.5mm .5mm oversize (1834cc)
2009 - 11 Yamaha FX SHO 10.5:1 Turbo
Stock Bore: 3.386 (86mm)
*Sold as Kit (4 pistons per kit)
**Piston sold complete with: rings, piston pin and locks
RING #
CPN-3386
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
SHO/FZR High Performance Racing Cylinder Sleeves 432-18000
LA Sleeve Yamaha 1.8L Engine Cylinder Sleeve
YA-5688
EXHAUST
R&D High Performance Racing Sleeves
are made to precise specifications specific
for the Yamaha FZR/SHO Supercharged
engine. R&D Racing Sleeves install easily and properly using the flanged “top
hang” register design. The “top hang” design when installed and seated
properly will not drop or slip which will allow 100 percent head gasket contact
for a positive head gasket seal. R&D Racing Sleeves are manufactured from
the highest grades of centrifugally cast “Molly 2000” Chrome Molly Iron Alloy
to provide superior strength and hardness. Trouble free installation, boring,
and honing using kit supplied installation instructions and tips on final hone
specifications for O.E.M. cast and R&D Forged Racing Piston Kits are
included. When the time comes to repair wavy, scored, seized, or worn
cylinders trust the pros at R&D. We have been re-sleeving race engines for
over 40 years. Sleeves are sold individually.
ENGINE/
GASKETS
SLEEVE
SURFACE
Deglaze Only
Deglaze Only
Deglaze Only
Deglaze Only
Bore & Hone
Bore & Hone
Bore & Hone
Bore & Hone
INATKE
SYSTEMS
PISTON
BORE OVER COMP.
DISP. SIZE
RING #
KIT #
SIZE RATIO
289959 1812cc
86mm
STD
8.6:1
JG1004-3386
292314 1812cc
86mm
STD
9.5:1
JG1004-3386
308631 1812cc
86mm
STD
10.5:1
JG1004-3386
308632 1812cc
86mm
STD
11.0:1
JG1004-3386
308633 1832cc 86.5mm +.5mm 8.6:1
JG1004-3405
308634 1832cc 86.5mm +.5mm 9.5:1
JG1004-3405
308635 1832cc 86.5mm +.5mm 10.5:1
JG1004-3405
308636 1832cc 86.5mm +.5mm 11.0:1
JG1004-3405
*Sold as Kit (4 pistons per kit)
**Piston sold complete with: rings, piston pin and locks
FZR HIGH PERFORMANCE
RACING CYLINDER
SLEEVES YAMAHA
1.8L ENGINE
YAMAHA
4 STROKE
JE PISTON KITS FOR YAMAHA
FX SHO 1800 (2009-2011)
*Sold individually
©2012 Hot Products. All rights reserved.
51
Description
Part No.
Carrillo Connecting Rod Set
YA-FXSHO>-9M5709S-04
Yamaha 1.8L 4 cylinder (sold 4 rods per set)
RIVA PRO-SERIES
4-STROKE CYLINDER
HEAD STUD KITS
RIVA’s ultra high strength cylinder head
stud kit is essential equipment when upgrading internal components on your
high boost Yamaha engine. Precision machined from premium grade 8740
alloy and heat treated to exacting tolerances, these studs dramatically
increase reliability & ease of maintenance.
Key Benefits Include:
• Superior material & heat treat process provide 10X better fatigue strength
than OEM bolts.
• Studs provide improved alignment of cylinder head and gasket for increased
reliability and ease of maintenance.
• More accurate & consistent torque loading provides a more uniform
clamping force on head gasket.
• Helps prevent blown head gaskets and assures optimum engine sealing.
Description
RIVA Pro-Series Cylinder Head Stud Kits
FX-SHO/FZR/FZS
Part No.
RY10040-HSK
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
RIVA PRO-SERIES
4-STROKE CYLINDER
HEAD GASKETS
CARRILLO CONNECTING RODS
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
52
Our Pro-Series Cylinder Head Gaskets were developed to withstand severe
heat & pressure generated by high-boost and high horsepower applications
delivering maximum reliability to your racing engine.
Key Benefits Include:
• Three layer stainless construction for durability & corrosion resistance.
• Viton coated & embossed surfaces for maximum sealing between head
and cylinder block.
• Unique design promotes even torque load across sealing surface &
requires no re-torque.
Description
Part No.
RIVA Pro-Series Head Gasket (Standard Bore) RY10040-CHG-86
FX-SHO/FZR/FZS
R&D FZR HIGH
PERFORMANCE
RACING HEAD GASKET
R&D High Performance Racing Head Gaskets were developed to replace the
O.E.M. head gasket with a higher performing Multi Layer Steel Stack Design
(MLS), utilizing state of the art materials proven to withstand extreme heat
generated from high cylinder pressures in high boost performance packages.
Each gasket is deep dual embossed (both sides) and Viton Coated to
promote a positive seal. Use the R&D Head Gasket with confidence in
standard replacement situations or Pro Race Engines. Our race proven
design maintains a positive seal with up to 24 pounds of boost. Available in
STD 86, 86.5, 87, 87.5, and 88mm bore sizes. R&D also offers a “Super Thin”
Gasket that will raise the compression level when changing piston ratio is not
an option.
NOTE: R&D also offers Custom R&D/CP High Performance pistons to fit any
bore size R&D Head Gasket. Gas porting also available upon request.
NOTE: No need to re-torque the head bolts after initial installation which is a
big plus on DOHC engines where cams would otherwise need to be removed.
Head torque specifications are included with each gasket
COMETIC YAMAHA 1.8L OEM
REPLACEMENT HEAD GASKET
Description
Cometic Yamaha 1.8L Engine Head Gasket 86mm*
*Available up to 90mm
©2012 Hot Products. All rights reserved.
Part No.
C6221
Description
R&D 86mm HP Head Gasket .027” 3 Layer
R&D 86.5 HP Head Gasket .027” 3 Layer
R&D 87 HP Head Gasket .027” 3 Layer
R&D 87.5 HP Head Gasket .027” 3 Layer
R&D 88 HP Head Gasket .027” 3 Layer
R&D HP Head Gasket 0.18” 2 Layer
(Specify Bore Size)
Part No.
080-01800
080-01801
080-01802
080-01803
080-01804
080-01810
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D HIGH PERFORMANCE
VALVE STEM SEAL KIT
Description
R&D High Perf Dual Valve Spring Kit (16 per kit)
RIVA’s high quality viton seals are extremely resistant to heat and abrasion.
Superior sealing keeps unwanted oil from contaminating combustion chambers and prevents air leakage through valve guides. A precision seal removal
& installation tool (RY19040-VST) is available separately. Sold in sets of 16.
Part No.
RY19040-PVS
RIVA YAMAHA
1.8L ENGINE
VALVE
RETAINER
UPGRADE KIT
Part No.
612-93001
R&D HIGH PERFORMANCE
VALVE SHIM KIT
R&D HIGH
PERFORMANCE
BOTTOM SPRING
RETAINER CUPS
R&D spring retainer cups will install
under the R&D valve spring and support and house the bottom of the spring
securely. The R&D Spring Retainer Cups must be used with the R&D spring
kits for proper assembly. Use R&D Valve Spring Shim Kits to fine tune valve
spring seat pressure.
Description
Part No.
R&D High Perf Bottom Spring Retainer Cups (set of 16) 612-93006
NOTE: For modified engines (Stage 3 & above) we recommend the complete
RIVA Valve Train Upgrade Kit (part # RY19040-VTU).
Description
RIVA Yamaha 1.8L Engine Valve Retainer
Upgrade Kit
Part No.
RY19040-SRU
RIVA VALVE TRAIN
UPGRADE KIT
RIVA’s Valve Train Upgrade Kits
increase the reliability of your modified
engine by reducing the possibility of
valve float at high rpm. Includes
lightweight, precision-machined
titanium valve retainers, racing valve
springs, and base washers.
Description
RIVA FX-SHO/FZR/FZS Valve Train Upgrade Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Part No.
612-93003
612-93004
612-93005
RIVA’s Valve Retainer
Upgrade Kit increases the reliability of your engine by reducing the possibility
of valve float at high rpm. Includes 16 lightweight, precision-machined
titanium valve retainers. A must for IJSBA & APBA Stock Class race craft.
BODY
The R&D spring base collar “shims” offer
precision valve spring tension shimming to fine
tune spring seat pressures based on boost
pressures the engine will run at. The R&D shim
kits are offered in the thicknesses of .010”, .020”,
and .030”.
Description
R&D .010” Thick Shim Kit (set of 16)
R&D .020” Thick Shim Kit (set of 16)
R&D .030” Thick Shim Kit (set of 16)
RIVA YAMAHA 1.8L
ENGINE PERFORMANCE
VALVE SEALS
EXHAUST
Description
RIVA Yamaha 1.8L Engine Performance
Valve Seals
Part No.
612-93007
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Engine Tuning Features
• 70-75 pounds at seat, 140-150 pounds at full lift (standard spec.)
• Shim friendly, add R&D spring collar base shims to add 2 pounds per .010 shim
• Allows the use of higher lift cams (up to +.080)
• Linear spring pressure curve allows smooth precision valve control
• High performance materials and surface finishes add to reliability
Description
R&D High Performance Valve Stem Seal Kit
ENGINE/
GASKETS
R&D offers High Performance Valve Stem Seal Kits
manufactured from only the best high quality Viton
rubber materials that will resist high valve guide and
oil temperatures to maintain a good valve seal in all
high rpm, high performance applications. When valve springs are changed out or
periodic head service work is being performed, trust R&D Valve Stem Seal Kits at
any performance level.
INATKE
SYSTEMS
R&D has developed an economical solution for
upgrading the valve train by offering a series of
upgrade parts that will work great with the
O.E.M. retainer and valve seals. R&D has
documented that the seat tension or pressure
on the stock springs is a low 52-55 pounds,
and coil bind on the stock springs occurs .050” after full lift on the stock cams. As
an industry rule or standard, as boost levels are increased to the engine, the valve
spring seat pressure should be increased 1-2 pounds per pound of boost. As an
industry rule, as RPM'S are increased, the spring pressure at full lift should be
increased as well to reduce or eliminate valve float at high rpm frequencies. With
the stock springs “short lift travel” shimming is NOT an option. Valve Springs MUST
be upgraded. Also to consider is valve spring travel at full cam lift, and to have
enough spring clearance freedom to run high performance camshafts or add
additional spring tension pressures without coil bind issues. The R&D spring kit
parts were developed and used with stock retainers during the 2009 season and
have proven their performance with an APBA/IJSBA Pro Open National
Championship. R&D dual springs are a “lightweight design” and manufactured
from ultra clean, high tensile material with multi step surface treatments to improve
fatigue strength and reliability. NOTE: R&D Spring Kits must use the R&D Bottom
Spring Retainer Cups kit Pt. # 612-93006 for proper assembly and seat pressures!
YAMAHA
4 STROKE
R&D HIGH PERFORMANCE
DUAL VALVE SPRING KIT
Part No.
RY19040-VTU
©2012 Hot Products. All rights reserved.
53
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
RIVA YAMAHA HIGH
PERFORMANCE VALVE SET
Drop-In Valve Kits: Standard size drop-in direct
replacement valves require no machining of
cylinder head.
Oversized Valve Kits: +1mm Intake/+1mm
Exhaust valves deliver more air flow
(requires machining of cylinder head).
Key Features:
• Stronger & lighter than stock valves.
• Redesigned valve heads for improved air flow & strength.
• High grade stainless intake valves resist corrosion.
• Inconel exhaust valves resist heat from high boost applications.
• Valve stems are hard-chrome plated for improved wear.
• Includes high strength valve locks.
• Sold in sets of 16 (8 Intake/8 Exhaust).
Description
RIVA Yamaha High Performance Valve Set
(Standard/Drop-in)
RIVA Yamaha High Performance Valve Set
(+1mm Intake / +1mm Exhaust)
The R&D Valve Stem Concentricity Gauge
is a testing tool to check the roundness
and trueness of valves. Small valves can
distort or bend from heat produced in high
performance supercharged or turbo
charged engines. To achieve a perfect
seal on the seat the valve needs to be concentric and true in every dimension.
Gauge is fully adjustable to accommodate a variety of valve sizes and
features a rigid, positive stop that can be set once and the trueness for an
entire set of valves can be measured. Kit comes complete with dial indicator
accurate to .001”. This is a must have tool for any engine builder to get the
most out of your high performance 4 stroke engine.
Description
R&D Valve Stem Concentricity Gauge
Part No.
612-80010
Part No.
RY19040-HPV-0
RY19040-HPV-1:1
Installation
RIVA VALVE COMPRESSION TOOL
Removal
RIVA YAMAHA 1.8L
ENGINE VALVE SEAL TOOL
This handy tool provides easy removal and installation of valve stem seals on
Yamaha 1.8L engines. Allows seal installation during fitting of valve train
upgrade kit without removing cylinder head.
Key features:
• Prevents seal distortion & gouging.
• Precision machined from 6061 aluminum & anodized.
• Knurled handle for positive grip.
Description
RIVA Yamaha 1.8L Engine Valve Seal Tool
Part No.
RY19040-VST
RIVA YAMAHA 1.8L
ENGINE VALVE
LIFTER BUCKETS
RIVA Performance Valve Lifter Buckets
are a “must have” item when
upgrading your engine’s valve train.
Designed to withstand the stress of
increased valve spring tension and RPM in modified engines that can cause
stock components to fail. Our lightweight valve lifter buckets are CNC
machined from heat treated billet steel providing superior strength and
durability. Order one kit per engine.
Description
Part No.
RIVA Yamaha 1.8L Eng. Valve Lifter Buckets RY19040-BVL-KIT
54
R&D VALVE STEM
CONCENTRICITY GAUGE
©2012 Hot Products. All rights reserved.
RIVA’s overhead Valve Compression Tool allows easy removal of valve springs
and keepers without removing cylinder head. Includes compression adapter to
pressurize cylinder keeping valves in place during removal of stock springs
and keepers. Fits both Yamaha 1.8L & Kawasaki 1.5L 4-stroke engines.
Description
RIVA Valve Compression Tool
Fits Yamaha 1.8L & Kawasaki 1.5L 4-stroke
Part No.
RY19040-VCT
FZR VALVE SPRING
COMPRESSION
TOOL KIT
The R&D Valve Spring Compression
Tool Kit allows easy removal of the
intake or exhaust valve springs and
keepers without removing the cylinder
head. R&D recommends using the compression adapter from a compression
gauge kit to pressurize cylinder keeping valves in place during removal of
springs and keepers.
Description
R&D FZR Valve Spring Compression Tool Kit
Part No.
612-92013
FZR CAM TENSIONER TOOL
The R&D Cam Tensioner Tool is designed to
mechanically spring preload the cam chain in
order to set and verify cam timing. This
eliminates the process of pressurizing the
hydraulic cam tensioner to verify cam timing.
Description
R&D FZR Cam Tensioner Tool
Part No.
612-92015
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D’s new RC2 Racing Camshaft kit offers a
serious boost in horsepower for the racer who
wants as much lift and duration that can be
safely “Bolted In” without valve guide or spring
base machining. The R&D RC2 Cam lobe profile has all of the same features in concept and
design as our RC1 recreational lobe, accept for
the increased lift and duration. The secret to the
R&D cam lobe is in the precision grind finish on
the cams base circle and duration at .050”.
R&D maintains strict specifications in this area
of the cam lobe which is the key to having
strong vacuum, a great idle tune, and clean
acceleration performance.
Description
R&D FZ/FZR/SHO RC1 Racing Cam Kit
Part No.
612-93009
NOTE: The R&D RC2 Racing Camshaft Grind Specifications have been
Race Proven during the 2009 and 2010 racing seasons. No other camshaft
has more lift and more duration than the RC2. The nearest competitor to
date is the Yamaha 1800 N.A. Cam with a total lift average of .368”. That puts
the RC2 a full .020” higher. R&D has worked hard in the duration curve area
of the cam paying careful attention to the duration at .050” and overall added
duration. R&D is currently working on the RC3 Racing Cam available in mid
October. The R&D RC2 camshaft kit is a performance modification that is
performed in a normal 5-7 day turnaround to your existing camshaft cores.
R&D also stocks Camshaft kits that can be mail ordered direct with a
reasonable additional cam core charge. R&D suggests that the FZ/FZR,
and SHO supercharged engines should benefit greatly from a supercharger
or turbocharger specific cam lobe profile design and custom LC and LSA
set up.
Description
R&D FZ/FZR/SHO RC2 Racing Cam Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
The R&D recreational camshaft kit is a performance modification regrind that
is performed in a normal 5-7 day turnaround to your existing camshaft cores.
R&D also stocks Camshaft kits that can be mail ordered direct with a
reasonable additional cam core charge. R&D camshaft specifications have
been performance tested against the 1800 naturally aspirated cams, and
clearly, there is no comparison in the tune ability area. R&D suggests that
the FZ/FZR, and SHO supercharged engines should benefit greatly from a
supercharger or turbocharger specific cam lobe profile and design. If
installing the R1 Cams with R&D Pro Tune Cam Timing Gears, a MoTeC or
comparable ECU must be used for tuning as aggressive lobe center changes
will reduce engine vacuum to lower than 15 inches and special custom tuning
will be required. R&D RC1 cams are a precision tolerance regrind. Valve
lifter re-shimming will be necessary. R&D will supply shimming specifications
with each cam set that will make valve adjustment easy. R&D recommends
the use of Hot Cams Shim Kits also available from R&D.
• Aggressive throttle response, increased overall horsepower
• Increased rpm performance (RPM range increased to 9500)
• Increased CFM airflow
• Horsepower increase gain (with R&D Cam Gears)
• Aftermarket ignition is required for custom tuning
• Works well with R&D Valve Spring Kit upgrades (Required)
• Easy installation • Bolt on 25+ Horsepower Upgrade
BODY
NOTE: The R&D RC1 Recreational Camshaft Grind Specifications have been
extensively endurance tested to be the best lobe profile for recreational riding
or offshore racing. The lift and duration are similar to the Yamaha 1800 N.A.
cam with a total lift average of .368”. The duration on the RC1 cam is less at
.050” lift over the N.A., however, the same 6° degree duration advantage is in
the recipe. That puts the RC1 comparable on lift, equal on overall duration
and a strong low end vacuum to allow the use of R1, R2, and R3 ECU’s.
R&D has worked hard in the duration curve area of the cam paying careful
attention to the duration at .050” and overall added duration.
NOTE: The R&D RC2 requires the installation of R&D’s High Performance
Valve Spring kit as the O.E.M. valve springs will run into coil bind with the
added lift on the RC2 lobe profile. The RC2 will also require the use of a
stand alone ECU system such as a MoTeC M400 to custom tune the fuel
and ignition for optimum performance.
EXHAUST
• Aggressive throttle response, increased overall horsepower
• Increased rpm performance (150-200 RPM Gain)
• Increased lift and duration (.368” lift and 6° degrees more duration)
• LC and LSA tunable (with R&D Cam Gears)
• 10-15 Bolt on Horsepower upgrade
• R&D R1, R2 and R3 ECU Compatible
• Works well with R&D Valve Spring Kit upgrades
• Easy installation
Overall lobe Lift and Durations are increased to allow as much lift as possible
and still run O.E.M. “uncut” valve guides. R&D has improved the lobe profile
with “state of the art” technologies that will reduce valve lifter friction and
improve valve lifter wear. The R&D “boost friendly” lobe profiles increased lift
and duration will produce a noticeable horsepower gain and can also be
tuned to custom LSA (lobe separation angles) when using R&D “Pro Tune”
Cam Gears (Pt. # 612-93008). The R&D RC2 will produce noticeable
horsepower gains over R&D RC1 recreational cams with improved gains
from idle to wide open throttle. The RC2 Cam Kit really goes to work adding
top end pulling power in the 8500-9500 rpm zone. R&D custom cams can
be installed easily and shimmed with basic hand tools and the O.E.M. service
manual. R&D High Rev Valve Spring and shim kit parts are required for the
RC2 Cam Kit to work properly without coil bind damage. Call R&D today
for further details and specifications for all your camshaft and valve train
upgrades.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Overall lobe Lift and Durations are increased to allow as much lift as possible
and still run O.E.M. “uncut” valve guides. R&D has improved the lobe profile
with “state-of-the-art” technologies that will reduce valve lifter friction and
improve valve lifter wear. The R&D “boost friendly” lobe profiles increased lift
and duration will produce a noticeable horsepower increases and work well
with C1, C3, and C5 Monster Wheels and also work well with R&D R1, R2,
and R3 ECU Reprogramming Services. R&D RC1 custom cams can be
installed easily and shimmed with basic hand tools and the O.E.M. service
manual in as little as two hours without the removal of the head, or any valve
spring or retainer parts. Call R&D today for further details and specifications
for all your camshaft and valve train upgrades.
ENGINE/
GASKETS
R&D’s RC1 Recreational/Racing Camshaft kit
offers a great boost in horsepower for the
recreational rider/racer who wants as much lift
and duration that can be “Bolted In” without valve
spring changes or valve guide machining. The
R&D RC1 will install and work well with O.E.M.
valve springs and retainers. The RC1 is a great
choice for recreational and offshore riding or
racing targeting the 7500-8500 RPM range for top
end power while also improving low and mid
range performance. The secret to the R&D cam
lobe is in the precision grind finish on the cams
base circle and duration at .050”. R&D maintains
strict specifications in this area of the cam lobe
which is the key to having strong vacuum, a great
idle tune, and clean acceleration performance.
INATKE
SYSTEMS
R&D YAMAHA FZ/FZR/SHO
RC2 RACING CAM KIT
YAMAHA
4 STROKE
R&D YAMAHA FZ/FZR/SHO
RC1 RACING CAM KIT
Part No.
612-93010
©2012 Hot Products. All rights reserved.
55
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
R&D YAMAHA
FZ/FZR/SHO
PRO TUNE
ADJUSTABLE
CAM GEAR KIT
R&D’s Racing Cam Gear kit allows a huge boost in overall horsepower to be
gained by custom tuning the camshafts LCA (lobe separation angle) set up.
Tuning the LCA with R&D Pro Tune Cam Gears can add 200-300 RPM’s,
increased boost pressure, and 2-3 MPH to your existing engine package.
Adjusting the camshafts LCA is a very simple “BOLT IN” modification with the
R&D Pro Tune Adjustable Cam Gear Kit. Understanding the LCA concept
principle is fairly easy. A wide LCA like found in the SHO and FZR will
generally result in decreased valve overlap, later intake events, earlier
exhaust events, and high intake manifold pressures which produce great idle,
smooth accelerating with mild low and top end power. Wide LCA’s are great
for school buses and soccer mom vans. However, if strong mid range pull
and top end horsepower is what you’re looking for, then a narrower LCA will
need to be generated. The R&D Pro Tune Cam Gear Kit allows the LCA
(lobe separation) to be adjusted narrower which will generate increased valve
overlap, earlier intake events, and later exhaust events. Resulting in snappier
throttle response, increased mid range and top end power and more boost.
Why spend big money on optional camshaft kits (i.e. 1800 N/A cams) that
have proven to offer too narrow of LCA compromising idle tune? Buy the
R&D Pro Tune Cam Gears designed specifically to improve overall power at
a fraction of the cost and provide an optimum overall tune. The R&D Cam
Gear Kit offers four possible LCA combinations that allow the cams to be
tuned depending on the type of riding or racing and type of fuel. In fact,
R&D has built a specific engine designated for degreeing, checking and
proving camshaft specifications. Depend on the Pro’s at R&D to deliver all
your horsepower needs.
• Aggressive throttle response, increased overall horsepower
• Increased rpm performance (+200-300 RPM Gain)
• Boost Pressure Increase (+1 pound) • 15-25 Horsepower Increase
• Precision CNC Billet/Ground Cam Gears (lighter than stock)
• R&D R1, R2, and R3 ECU Compatible
• Works well with R&D Cam Regrind and Valve Spring Kit upgrades
• Easy installation • Bolt on Higher Horsepower Upgrade
NOTE: R&D has determined that the O.E.M LCA is a WIDE 120 degrees
stock, with an intake cam lobe center of 122.5 degrees. Considering the LCA
timing facts, using the R&D Pro Tune Cam Gears to tune the cams will generate huge performance power gains. R&D has found in testing that a 2.5
degree LCA change will act similar to a 1 pound boost addition. Tests have
proven that an R&D C1 or C3 compressor wheel and a 7 degree LCA
change can have the same performance advantages as a 15 pound
compressor wheel. Call R&D for constant power upgrade information as
we are constantly at work looking for more.
Description
R&D Yamaha FZ/FZR/SHO Pro Tune Adjustable
Cam Gear Kit
Adjustable Cam Sprocket Kit delivers a significant increase in horsepower,
speed & RPM through easy cam timing adjustment. Our ‘Quick-Tune’ design
features color coded timing inserts that lock-in desired cam adjustment in
minutes without removal of cam tensioner, camshaft or cam sprocket (after
initial installation). Design allows fast & easy timing adjustment; saving hours
of time when testing and tuning. Sprockets are precision machined from billet
steel and heat treated for maximum durability.
Key Features Include:
• Allows fast & easy adjustment of cam timing for maximum performance.
• Quick-Tune timing inserts lock-in cam timing in minutes.
• Designed for both SHO & HO Yamaha 1.8L engines.
• Works well with both stock and performance cams.
• Easy bolt-on installation.
• Includes complete instructions with tuning guide.
Description
RIVA Yamaha 1.8L Engine Adjustable Cam
Sprocket Kit
Part No.
612-93008
R&D CAM
TENSIONER GASKET
R&D's new Cam Tensioner Gasket has a metal
reinforced center that enables it to be reusable.
Description
R&D Cam Tensioner Gasket
56
RIVA YAMAHA 1.8L ENGINE
ADJUSTABLE CAM SPROCKET KIT
©2012 Hot Products. All rights reserved.
Part No.
080-21025
TREY FRAME - BLACK STAR RACING
HOT PRODUCTS SPONSORED RIDER
Part No.
RY19040-ACS
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
YAMAHA
4 STROKE
INATKE
SYSTEMS
ENGINE/
GASKETS
Description
Turbocharge Engine Kit
REAR EXHAUST KIT
Part No.
RY17040-PC-I
RY17040-TIK
RY17040-BOV-SSQV
INTERCOOLER FOR VXR/VXS
AIR INTAKE KIT
BODY
• Genuine screen type K&N flame arrestor.
• Large 4” smooth-bore ducting.
• Water repellant pre-filter.
• Billet band clamps.
Part No.
RY15050-TREK
Description
RY15040-TREK Yam FZR/FZS Turbocharge Power Filter Kit
Yam FX-SHO (2008-11) Turbocharge
RY15070-TREK Power Filter Kit
Yam FX-SHO (2012) Turbocharge
RY15060-TREK Power Filter Kit
Yam VXR/VXS Turbocharge Power Filter Kit
Part No.
RY13050-TPF
RY13040-TPF
RY13070-TPF
• Engine Internals Upgrade Kit
-Engine Internal Upgrade Kit
• Engine Cooling Upgrade Kit
-Engine Cooling Upgrade Kit
• Engine Management
-RIVA/Athena
-RIVA/Vi-PEC
-Mo TeC
• Pump & Handling
-Intake Grate
-Pump Impeller
-Modified Pump Housing
-Reduction Nozzle
-Ride Plate
RY13060
©2012 Hot Products. All rights reserved.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
REQUIRED ADDITIONAL COMPONENTS:
• Fuel & Intake
-High Capacity Fuel Injectors
-Fuel Pressure Regulator Kit
-High Capacity Fuel Pump
-Intake Manifold Upgrade Kit
-RIVA/Wilson Billet Intake Manifold
(over 18psi boost)
Description
GEN-2’ Power Cooler
Aluminum Intake Tube Kit
(Turbocharger to Power Cooler)
HKS SSQV Blow-off Valve Kit
Part No.
Part No. Description
RY17060-PC
RY18040-TEK GEN-2’ Power Cooler Kit
Includes Aluminum Intake Tube - Turbocharger to Power Cooler
HKS SSQV Blow-off Valve Kit
RY17040-BOV-SSQV
• Mandrel bent water jacketed aluminum exhaust down pipe.
• A/F ratio sensor mount in exhaust tubing.
• Water injection system to suppress sound.
• Stainless steel hose clamps.
• Billet aluminum rear exhaust through-hull outlet (4-inch).
Description
Yam FZR/FZS Turbocharge Rear Exhaust Kit
Yam FX-SHO (2008-11)Turbocharge Rear
Exhaust Kit
Yam FX-SHO (2012) Turbocharge Rear
Exhaust Kit
Yam VXR/VXS Turbocharge Rear Exhaust Kit
INTERCOOLER FOR FZR/FZS,
FX-SHO (2008-12)
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
ENGINE KIT
• TiAL Sport racing turbocharger (water jacketed stainless steel turbine
housing; Garrett GT30R ball bearing CHRA w/billet compressor wheel;
integrated wastegate).
• Billet CNC machined aluminum turbo mounting bracket kit.
• Billet CNC machined aluminum exhaust manifold flange.
• Mandrel bent water jacketed stainless steel exhaust pipe
(exhaust manifold to turbo).
• Stainless steel V-band clamps.
• Braided stainless steel oil line kit.
EXHAUST
RIVA RACING YAMAHA FZR/FZS TURBOCHARGER SYSTEM
RIVA RACING YAMAHA FX-SHO TURBOCHARGER SYSTEM (2008-11)
RIVA RACING YAMAHA FX-SHO TURBOCHARGER SYSTEM (2012)
RIVA RACING YAMAHA VXR/VXS TURBOCHARGER SYSTEM
57
R&D FZR AQUAVEIN
INTAKE GRATE
The huge FZR pump intake
demands strength and an extra
large wing for maximum hook up.
FZR
The new R&D FZR grate utilizes an
112-18001
all new ultra strong 3 bar front
mount strut design to support a new "extra wide" forward mounted wing that
is guaranteed to top load the FZ pump with enough water to stay hooked up
and moving forward in the roughest water conditions. The new "SUPER
DEEP" race legal bars are the biggest and strongest we have ever built to
deliver unmatched strength. The new 3 bar concept and "Flat Faced" wide
wing proved out to provide superior cornering over previous single bar
designs. Big pump inlets need big grates, and that’s what we have built.
* For proper installation R&D recommends the use of the R&D Pump Shoe
Seal Kit (Pt. # 162-00007)
Description
R&D FZR Aquavein Intake Grate
R&D FZR Pump Seal Kit
FX SHO
112-18000
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
58
RIVA FZR/FZ
STAINLESS STEEL
TOP-LOADER INTAKE
GRATE
RIVA’s revolutionary new intake grate
for FZR/FZS delivers the ultimate in
speed, hook up & strength. All new
design features oversized top loader
wing and optimized inlet ramp for
closed course and offshore racing.
Bulletproof stainless steel construction makes this grate virtually indestructible
and eliminates the need for additional restrictive support bars. Race bred
design significantly reduces cavitation and provides superior handling along
with unmatched durability in extreme conditions.
Description
RIVA FX Stainless Steel Top-Loader Intake Grate
R&D AQUAVEIN
INTAKE GRATE
Part No.
112-18000
112-18020
Part No.
RY22050-1
RIVA YAMAHA
INTAKE GRATE
Part No.
112-18001
162-00007
Description
R&D FX SHO Aquavein Intake Grate
R&D VXR/VXS Aquavein Intake Grate
RIVA’s Top-Loader intake
grate improves hook up
and handling in rough
conditions. Center wing
eliminates prop spin and
RY22040
cavitation found with the
stock grate along with the
SHO/VXR’s tendency to drop on its nose when the throttle is let off at high
speeds. Powder coated to prevent corrosion.
Description
RIVA FX-SHO/08-10 FX Intake Grate
RIVA VXR/VXS Intake Grate
Part No.
RY22040
RY21030
R&D PUMP
SEAL KIT
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
R&D's new pump seal kit
stuffs up all the unwanted
cavities in the pump shoe
that aid in producing
cavitation. This kit offers a
way to seal the pump shoe,
which will reduce cavitation
and increase pump efficiency
and performance.
Description
FX SHO Pump Seal Kit for OEM Intake Grate
FX SHO Pump Seal Kit for RIVA Racing Intake Grate
FX SHO Pump Seal Kit for R&D Aquavein Intake Grate
FZR Pump Seal Kit for OEM Intake Grate
FZR Pump Seal Kit for R&D Aquavein Intake Grate
VXR Pump Seal Kit for Stock Scoop Grate
VXR Pump Seal Kit for R&D Aquavein Intake Grate
©2012 Hot Products. All rights reserved.
Part No.
162-00003
162-00004
162-00005
162-00006
162-00007
162-00008
162-00009
FX-SHO - RY25040
FZR/FZS - RY25050
RIVA PUMP SEAL KITS
Dramatically reduce cavitation and prop spin with our easy to install Pump
Seal Kits. Location specific, molded inserts fill the voids in OEM pump inlet
shoe that bleed air into pump causing cavitation. Recommended for modified
craft using aftermarket intake grates. Includes detailed installation instructions.
Description
RIVA FX-SHO Pump Seal Kit
RIVA FZR/FZS Pump Seal Kit
Part No.
RY25040
RY25050
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
YAMAHA
4 STROKE
INATKE
SYSTEMS
ENGINE/
GASKETS
Description
RIVA FX-SHO Performance Ride Plate
RIVA FZR/FZS Performance Ride Plate
RIVA VXR/VXS Performance Ride Plate
Part No.
RY21040
RY21050
RY21060
BODY
FX SHO
122-18000
Part No.
122-18001
122-18004
Key Benefits Include:
• Superior handling performance.
• Quicker planing & improved top speed.
• Reduced porposing.
• Improved straight line tracking at high speed.
• Race bred design.
• Improves acceleration, cornering and straight line handling.
• Turnable with included shims.
• Powder coated to prevent corrosion.
• IJSBA/APBA Race Legal.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D HIGH
PERFORMANCE
RIDE PLATE
The new R&D SHO Pro
Series Ride Plate will meet
the demands in performance
whether being used for
weekend recreational riding,
closed course racing, or offshore competition. Increased top speed performance
of .50 to 1 MPH over stock, and compromises nothing when turned loose in rough
water conditions. Bow search with full fuel loads is alleviated completely.
• 1 MPH top speed improvement • Unique multi-step concept
• Improved straight line stability • Significantly improved cornering
• Reduced chine walking on high speed sweepers
• Drives through chop with superior stability
• Retains reverse gate mounting and operation
Description
R&D FX SHO High Performance Ride Plate
Part No.
122-18000
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
R&D FZR Pro Series Ride Plate
R&D VXR/VXS Pro Series Ride Plate
RIVA PERFORMANCE RIDE PLATE
RIVA’s Ride Plate delivers the perfect balance of top speed and improved
handling in a variety of water conditions and speeds. Its race bred design
features deep channels for improved acceleration and traction in turns.
Provides excellent straightline stability at high speed with reduced porposing.
Utilizes stock ride plate support brackets and accepts OEM speedo sensor.
EXHAUST
R&D PRO SERIES RIDE PLATE
The new R&D Adjustable Ride Plate delivers a perfect balance of increased
top speed performance, improved cornering capabilities, and superb straight
line stability. The new adjustable design utilizes kit supplied shims to fine tune
the performance for a perfect balance of speed/handling for rider weight or
water conditions from drag to surf. Increased top speed performance and
compromises nothing when turned loose in rough water conditions. The
design utilizes the vital OEM hull protection stainless steel pads, which safely
disperse the pressure loads from the ride plate over a larger area on the hull.
The new R&D FZR Adjustable Pro Series Ride Plate will meet the demands
in performance whether being used for weekend recreational riding, closed
course racing, surf, or offshore competition. Made in the USA from cast
aluminum and powder coated for corrosion resistance.
• Top speed improvement
• Adjustable design
• Unique multi-step concept
• Improved straight line stability
• Significantly improved cornering
• Reduced chine walking on high speed sweepers
• Drives through chop with superior stability
• Retains reverse gate operation
2010 WORLD FINALS • LAKE HAVASU, AZ
PHOTO COURTESY OF JIN OMURA
©2012 Hot Products. All rights reserved.
59
RIVA VXR/VXS PRO-SERIES
STEERING SYSTEM
RIVA FZ PRO-SERIES STEERING SYSTEM
Introducing the ultimate race proven steering system for your Yamaha
FZR/FZS. Fully adjustable design features a dual tube steering head for
maximum strength & rigidity. Directly replaces bulky OEM mechanism with
a stronger & lighter unit that provides variable height and tilt positions.
Delivers a precision feel and the confidence to push your craft to the limit
with improved dependability and comfort. Bulletproof bar clamp will accept
any 7/8" handlebar or 1 1/8" fat bar. Includes all necessary installation
hardware and instructions. Requires use of aftermarket handlebars.
Key Features:
• Superior strength & rigidity over OEM system.
• Billet stainless steel steering shaft is much stronger than the OEM
aluminum shaft.
• Cutting edge race styling.
• Variable height and tilt adjustment.
• Accepts both 7/8" bars & 1 1/8" bulge bars.
• Billet steering arm features adjustable "quick turn" settings.
• Retains Off Throttle Steering system.
• Race tested & proven on 2010 IJSBA/APBA tours.
• All aluminum parts anodized to prevent corrosion.
• Standard 3.5" tubes provide adjustment +/- 1" from OEM low position.
• Optional 5-1/2" & 7-1/2" tubes provide additional height choices.
Description
RIVA FZ /FZS Steering System
5 1/2” Tube Kit
7 1/2” Tube Kit
Part No.
RY20050-U-3.5
RY20050-RK-5.5
RY20050-RK-7.5
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • CONTROL
60
SATO ENGINEERING
FZR/FZS STEERING SYSTEM
This billet steering system is the ultimate upgrade for the new Yamaha FZ
watercraft. The system is extremely strong and allows the rider to change to
handlebars of their choice.
Description
Sato Engineering FZR/FZS Steering System
©2012 Hot Products. All rights reserved.
Part No.
SE-027020
RIVA’s VXR/VXS steering system directly replaces bulky OEM mechanism
with a stronger & lighter unit that provides variable tilt adjustment. Delivers a
precision feel and the confidence to push your craft to the limit with improved
dependability and comfort. Bulletproof bar clamp will accept any aftermarket
7/8" handlebar or 1-1/8" fat bar. Includes all necessary installation hardware
and instructions. Requires use of aftermarket handlebars.
Key Features:
• Superior strength & rigidity over OEM system.
• Billet stainless steel steering shaft is much stronger than OEM aluminum shaft.
• Cutting edge race styling.
• Variable tilt adjustment.
• Accepts both 7/8" bars & 1-1/8" fat bars.
• Billet steering arm features adjustable "quick turn" settings.
• Retains Off Throttle Steering system.
• Integrated throttle cable retention bracket.
• All aluminum parts anodized to prevent corrosion.
Description
RIVA VXR/VXS Pro-Series Steering System
Part No.
RY20060-U
R&D FX-SHO/FZR/FZS
BILLET STEERING
SYSTEM KITS
The new R&D Billet Steering System was
developed and tested during the 2009
APBA/IJSBA National and World
Championships and is a proven winner in
design and performance. R&D’s Billet design
offers superior strength and lighter weight over
the OEM steering system. Utilizing a 7/8” MX
handlebar, allows the rider to personalize the
bar setup to their liking. R&D chose the 7/8”
diameter bar type over the Fat bar, because of
the space watercraft bars need for start/stop
switches, VTS switches, and custom trim lever
systems. When using fat or taper bars, the bar
widths are forced wider than comfortable in a watercraft application.
R&D offers two types of Handlebars for the new billet steering system, MX
Low for short to average height pilots and MX high for taller pilots. Handlebars
sold separately. The R&D Steering System is the way to go when setting up
the ergonomic steering comfort “your way”.
• 3 pounds lighter than stock system
• Easy installation (1 hour) includes all hardware and instructions
• Increases overall comfort and handling performance
• Allows custom bar setups (set up your way)
• Utilizes 7/8” diameter handlebars of our choice
• Adds a true “Factory Racing” look to your watercraft
Description
R&D FZR / FZS Billet Steering System
R&D FX-SHO Billet Steering System
Part No.
512-18000
512-18001
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
Part No.
162-18020
Part No.
122-01800
122-01801
122-01820
RIVA YAMAHA
FX-SHO/FZR/FZS/VX
SPONSON KIT
Part No.
RY2625
WORX RACING
YAMAHA SHO/FZR/FZS
SPONSONS
Fitting Worx sponsons provide unbelievable
cornering, better control in the rough and
predictable inline tracking while towing
wakeboards or waterskiers. Worx sponsons
are easy to fit, look great and bolt right into
stock mounting holes.
Description
Worx Racing FX-SHO Sponsons Kit
Worx Racing FZR/FZS Sponsons Kit
Part No.
WR542
WR543
Description
R&D FX-SHO/FZR/FZS
Hydro Force Steering Nozzle
Part No.
162-14000
R&D FX-SHO/FZR/FZS
VTS QUICK SHIFT
CAM KIT
The R&D FX-SHO/FZR/FZS VTS Trim Driver Cam is a cam device that
installs directly in place of the O.E.M. plastic VTS trim driver cam. The R&D
cam is designed to recalibrate the trim position amount from an O.E.M. 7 to 8
degree per shift to a finer and speed friendly 4 degree per shift. The O.E.M.
SHO neutral position setting is 85 degree or 5 degree up from horizontal
zero. The new recalibrated position with the new R&D Trim Cam is 87.5
degrees or 2.5 degree up from horizontal zero. The R&D Trim Cam will deliver
a more positive group of adjustments that will allow much better turning
capabilities, as well as finer adjustments for rough water conditions. The R&D
Trim Cam will work with the O.E.M. trim nozzle assembly, or the R&D Auto
Trim Kit.
Description
R&D FX-SHO/FZR/FZS VTS Trim Driver Cam Kit
Part No.
162-18010
©2012 Hot Products. All rights reserved.
BODY
Description
RIVA FX-SHO/FZR/FZS/VX Sponsons Kit
R&D’s new Hydro Force Steering Nozzle for the FX-SHO/FZR/FZS is a direct
replacement nozzle. The new lengthened design delivers a full 1 MPH speed
gain over stock. The adjustable pivot position improves the turning radius
allowing you to carve tighter turns with a more positive feel. Improved
performance through speed, acceleration and handling.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Unique blade design provides
a significant improvement to
the handling characteristics.
Reduces rough water hunting and
rolling sometimes experienced with
stock sponsons. Sponson depth is
adjustable to control the amount of influence they have on craft. Easily
installs to stock mounting points with our bulletproof mounting system that
features billet inserts in sponson fins.
Fits all Yamaha FX-SHO, FZR, FZS & VX models.
R&D FX-SHO/FZR/FZS
HYDRO FORCE STEERING NOZZLE
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
FX-SHO/FZR/FZS/VXR/VXS Auto Trim Nozzle Kit
EXHAUST
The R&D FX-SHO/FZR/FZS Auto Trim Kit was developed to accommodate
the O.E.M. VTS Quick Shift System with a fully adjustable and fully automatic
trim system! The R&D Auto Trim automatically drops a rider preferred and
adjustable 2-8 degrees. Drive from turn to turn never worrying whether the
trim is in the best position for perfect turn negotiation! The R&D Auto Trim
allows you to set the trim up your way to carve perfect turn every time! For
long straight rides the R&D Auto Trim System works in conjunction with
O.E.M VTS, so stock trim settings are retained, while the R&D Auto Trim
takes over in the turns. The combination allows the best of both worlds for
recreational and closed course riding!
ENGINE/
GASKETS
Description
R&D FX-SHO Sponson Kit
R&D FZR/FZS Sponson Kit
R&D VXR/VXS Sponson Kit
R&D FX-SHO/FZR/FZS/VXR/VXS
AUTO TRIM NOZZLE KIT
INATKE
SYSTEMS
The new R&D Yamaha SHO Pro
Series Sponson Kit was designed
and developed with all new
generation performance concepts
in mind to deliver a whole new
level of handling and speed performance with offshore and closed course
race proven adjustability options. The R&D Pro Series Sponson Kits have
been extensively offshore, race track, and 1 and 2 up recreational tested to
guarantee a comfortable setting for any riding style or condition! The R&D
Sponson Kit will deliver higher top speed performance and a much smoother
and more predictable ride over O.E.M. sponsons. Low speed and high-speed
turns are a breeze with new found control. The secret to R&D’s new
generation concept is in the backing plate design with an aftermarket first,
low pressure, low friction concept that breaks up and relieves speed robbing
drag within the sponson’s backing plate channel. The new R&D design
staggers the sponson blades fins water trapping area to pick up less water in
the front and more in the back. The stagger/step-up concept greatly reduces
chine walk in high speed corners, while allowing more rear end grip. There is
also a higher end recreational/race setting with enough grip for the best of
pro’s! Finally there is an aftermarket sponson kit that really does it all! More
top speed due to less drag, less chine walking, racer preferred rear end grip,
and unmatched straight line stability.
YAMAHA
4 STROKE
R&D YAMAHA
FX-SHO/FZR/FZS
SPONSON KIT
61
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • PUMP
R&D FX-SHO/FZR/FZS/VXR/VXS
PERFORMANCE EXIT NOZZLE
The new R&D cast aluminum exit nozzle is designed
to fine tune the pump and prop to maximize
performance and rpm. The new R&D exit nozzle is
available in 2.5 and 5 degree up sweep angles. The 5 degree positive angle
lightens the nose of the craft and adds top speed; this is great for recreational
use. The 2.5 degree delivers improved performance in rough water conditions
by producing more nose pressure to drive the hull through the bumps; this
design is perfect for closed coarse and offshore competition. Both types are
available in bore sizes of 80, 80.5, 81, and 81.5. *Custom bore sizes from 80
to 90 available at no extra charge, specify size when ordering. The maintenance free R&D cast aluminum and powder coated one piece construction
exit nozzle is the better alternative to a removable ring design. With the new
R&D nozzle the OEM reliability and safety is retained, because there is not a
removable ring sleeve to vibrate loose, falls out and gets wedged in the
steering nozzle creating a whole new definition to the term BUCKING.
Description
R&D Perf. Exit
R&D Perf. Exit
R&D Perf. Exit
R&D Perf. Exit
Nozzle
Nozzle
Nozzle
Nozzle
2.5
2.5
2.5
2.5
80mm
80.5mm
81mm
81.5mm
Part No.
162-82800
162-82805
162-82810
162-82815
**Custom bore sizes available at no extra charge, specify size when ordering**
Description
R&D Perf. Exit Nozzle 5 degree 80mm
R&D Perf. Exit Nozzle 5 degree 80.5mm
R&D Perf. Exit Nozzle 5 degree 81mm
R&D FZR Perf. Exit Nozzle 5 degree 81.5mm
Part No.
162-85800
162-85805
162-85810
162-85815
**Custom bore sizes available at no extra charge, specify size when ordering**
RIVA FX-SHO/FZ PRO-SERIES
REDUCTION NOZZLE
R&D’s new SHO/FZR Anti-Cavitation
Transom Plate Machining Modification service is now available. The
engineers at R&D have been successful at reducing pump cavitation by
removing the restriction in the OEM Transom Plate. The OEM Transom Plate
has a 3mm taper that restricts water flow in front of the prop. Removing this
restriction significantly reduces cavitation and improves holeshot and hook
up with any prop type or diameter. The service includes line boring the
Transom Plate and blue printing the new pump shoe diameter to blend with
the R&D Aquavein Intake Grate, and the sealing surface of the transom
plate where it mounts the hull is also improved by plugging the OEM casting
pocket in the face of the Transom Plate with R&D’s Sure Seal Urethane
Material. R&D also offers the service to a new OEM Transom Plate available
for immediate shipping.
Description
R&D Transom Plate Machining Service
R&D Complete new FZR Transom Plate
w/Machining Service
R&D Complete new SHO Transom Plate
w/Machining Service
Part No.
162-18004
162-18005
162-18006
Our Pro-Series Reduction Nozzle is ideal for
tuning your Yamaha pump combination to
maximize performance. Nozzle exit diameter can
be easily changed via interchangeable ring
system. Looking for more RPM or acceleration power? Insert a larger
diameter ring. Want more top speed or less RPM? Install a smaller diameter
ring. Nozzle includes three precision-machined stainless steel rings in
graduated sizes (81, 82 & 83mm). Additional ring sizes available.
Note: Nozzle eliminates water spout function to maximize performance and
conform to racing safety rules.
Description
RIVA FX-SHO/FZ Pro-Series Reduction Nozzle
Part No.
RY23040-N
R&D FX-SHO/FZR/FZS/VXR/VXS
ANTI-CAVITATION CONE
The R&D Anti-Cavitation Pump Cone Kit will reduce
overall internal pump cavitation within the Yamaha's offset
reduction/compression nozzle design. The O.E.M.
reduction/compression nozzle is offset, while the O.E.M. pump cone/bearing
cap remains straight which causes uneven pressures within the pump and
reduction nozzle. The R&D Anti-Cavitation Pump Cone is offset and
reshaped to match the O.E.M. reduction nozzle offset promoting even pressures, which will substantially reduce cavitation, increase pump hook up,
boost acceleration, and increase top speed performance.
Description
R&D Anti-Cavitation Cone
62
degree
degree
degree
degree
SHO/FZR R&D
ANTI-CAVITATION
TRANSOM PLATE
MACHINING
MODIFICATION
©2012 Hot Products. All rights reserved.
Part No.
162-18000
RIVA BILLET DRIVESHAFT
SLEEVE KITS
RIVA’s precision machined Billet Driveshaft Sleeve is a direct replacement for
the thin factory rubber hose that is prone to distortion and failure. Sleeve is
constructed of 6061 aluminum and is anodized to prevent corrosion. Kit
includes high quality silicon couplers and stainless steel clamps. This
upgraded sleeve kit is highly recommended for performance applications due
to increased pump pressure that accelerates failure of original rubber hose.
Description
RIVA Billet Driveshaft Sleeve Kit FX/FZ All
RIVA Billet Driveshaft Sleeve Kit VXR/VXS
Part No.
RY30040-DSS
RY30060-DSS
YAMAHA FX-SHO/FZ/VXR/VXS • PUMP
Year
09-12
09-12
2012
2012
08-12
08-12
Description
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Stock
12/20
11/19
11/18
11/18
11/19
11/19
11/19
12/19
12/20
13/20
13/21
13/22
13/23
13/24
13/25
Limited
---------12/19
12/19
----------
Modified
--------13/20
13/20
---------
Part No.
SY557525SW1119
SY557525SW1219
SY557525SW1220
SY557525SW1320
SY557525SW1321
SY557525SW1322
SY557525SW1323
SY557525SW1324
SY557525SW1325
Inducer
The new Twin Prop design drives of the line much quicker than the traditional
single prop, and offers a substantial increase in rough water hookup.
Main Drive
Main Drive
Main Drive
Engine Mods
Stock
Limited
Supermod
Pitch
12/18
12/20
13/23
Part No.
SY557525SWM1218
SY557525SWM1220
SY557525SWM1323
Inducer
Inducer
Inducer
Engine Mods
Stock
Limited
Supermod
Pitch
12/17
12/17
14/18
Part No.
SY440ID1217
SY440ID1217
SY440ID1418
Solas Recommends:
Part No.
FX-SHO/FZ Stock Replacement Impeller
YS-DF-14/21
FX-SHO/FZ Limited Boat Replacement Impeller YS-DF-15/22
FX-SHO/FZR/FZS/VXR/VXS
R&D PRO COMP CLUTCH
SAVER BILLET DRIVELINE COUPLER SET
R&D Performance is proud to announce the release of the new SHO/FZR
Pro Comp Clutch Saver Driveline Couplers. The new clutch saver design
increases the rotational mass of the 1800cc engine. The engineers at R&D
added approximately 1.5 pounds of weight to the driveline couplers to
increase the rotational mass of the engine. The added mass dampens the
moment of inertia and absorbs shock that the supercharger clutch and pump
impeller receive each time the engine accelerates. The result is smoother
engine performance with added clutch life and reduced prop shock and cavitation. These precision couplers are made from billet aircraft aluminum and
CNC machined to exact tolerance.
Also available for MOD SHOP conversion hull kits.
Description
R&D Billet Coupler Set SHO/FZR/VXR/VXS
Part No.
612-01801
FX-SHO/FZR/FZS/VXR/VXS
IMPELLER SHAFT
HOLDER TOOL
Developed specifically for the FX-SHO/FZR/FZS/VXR/VXS
watercraft, this tool is required to change the impeller.
20mm splined.
Description
FX-SHO/FZR/FZS/VXR/VXS Impeller Tool
BODY
SKAT-TRAK
FX-SHO/FZR TWIN IMPELLERS
Part No.
YS-DF-13/22R
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Main Drive
Description
RIVA Solas Dynafly Impeller 13/22R
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Model
FZR
FZS
VXR
VXS
FX-SHO
FX-Cruiser HO
EXHAUST
Includes a billet nose boot and impeller wrench.
ENGINE/
GASKETS
SKAT-TRAK FX-SHO/FZR/VXR/VXS
155-75-25 SWIRL IMPELLERS
INATKE
SYSTEMS
This all new impeller delivers
unmatched acceleration & top
speed in Yamaha FX-SHO/FZ
applications. The "R" Series
impeller is precision tuned to RIVA specifications using a pitch block fixture.
This offers a higher level of consistency when matched with RIVA Performance
Kits. Includes billet impeller cone that locks solidly into place with 3 stainless
set screws. Ideal for RIVA Stage 1 applications or higher levels of modification
when matched with RIVA Pro-Series FX-SHO/FZ Reduction Nozzle
(part# RY23040-N).
YAMAHA
4 STROKE
RIVA SOLAS
DYNAFLY
R-SERIES
IMPELLER
Part No.
TOOL #53
©2012 Hot Products. All rights reserved.
63
YAMAHA FX-SHO/FZ/VXR/VXS • BODY
YAMAHA
4 STROKE
RIVA PERFORMANCE
RECOMMENDATION PARTS LIST
INTAKE
SYSTEMS
YAMAHA FX-SHO - STAGE 1
PERFORMANCE DATA
Stock
67 MPH @ 7,500
Stage 1
70-71 MPH @ 7,600 RPM
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
& CONTROLS /BILGE
HANDLING
EXHAUST
ENGINE/
GASKETS
Note: All testing performed with 1/3 tank of fuel; trim neutral.
Stage 1 Performance Parts
Description
RIVA FZ BILLET MIRROR BLOCK-OFF KIT
RIVA’s billet Block-off Kit covers the opening left in the hood when mirrors are
removed for competition. Enhances craft's sleek lines and aerodynamics. Easy
installation requires no special tools. Precision machined from billet aluminum
and anodized to prevent corrosion. Includes installation hardware.
Description
RIVA FZR/FZS Billet Mirror Block-Off Kit
RIVA
VXR/VXS/VX
MIRROR
BLOCK-OFF
KIT
RIVA’s billet Block-off
Kit covers the opening
left in the hood when mirrors are removed for competition. Enhances craft's
sleek lines and aerodynamics. Easy installation requires no special tools.
Precision machined from billet aluminum and anodized to prevent corrosion.
Includes rubber mounting pad & installation hardware. Fits all 2010-2011 VX
& 2011 VXR/VXS.
Description
RIVA VXR/VXS/VX Mirror Block-off Kit
1
1
1
1
1
1
1
Part No.
RY13040
RY12040-IMUK
RY16040
RY25040
RY22040
YS-DF-13/22R
RY21040
YAMAHA FZR - STAGE 1
PERFORMANCE DATA
Stock
67 MPH @ 7,500
Stage 1
70-71 MPH @ 7,600 RPM
Note: All testing performed with 1/3 tank of fuel; trim neutral.
Stage 1 Performance Parts
Description
Performance Power Filter Kit
Intake Manifold Upgrade Kit
Free Flow Exhaust Kit
Pump Seal Kit
Stainless Steel Intake Grate
R-Series DynaFly Impeller
Performance Ride Plate
Quantity
1
1
1
1
1
1
1
Part No.
RY13040
RY12040-IMUK
RY16040
RY25050-1
RY22050-1
YS-DF-13/22R
RY21050
Part No.
RY5-VXR-MB
RIVA
VXR/VXS/VX
REAR STORAGE
TUB
Add 4 gallons of convenient
under-seat storage to your VX or
VXR/VXS watercraft. Durable
plastic storage tub removes
easily to allow access for
maintenance. Fits all 2010-2011
VX & 2011 VXR/VXS
Description
RIVA VXR/VXS/VX Rear Storage Tub
64
Part No.
RY5-FZ-MB
Quantity
Performance Power Filter Kit
Intake Manifold Upgrade Kit
Free Flow Exhaust Kit
Pump Seal Kit
Top-Loader Intake Grate
R-Series DynaFly Impeller
Performance Ride Plate
©2012 Hot Products. All rights reserved.
Part No.
RY4-RST-060
2012 IJSBA HOT PRODUCTS MARK HAHN MEMORIAL
HAVASU 300 ENDURANCE RACE IN LAKE HAVASU CITY, ARIZONA
AERO ASWAR FROM INDONESIA
YAMAHA FX-SHO/FZ/VXR/VXS • SEAT COVER
GENUINE
YFZR101-B
Part No.
AZ-SEWFX1
AZ-SEWFZR
AZ-SEWFZS
PRE-COLORED HOT PRODUCTS
RECOMMENDED HYDRO-TURF SEAT COVERS
FZR Series (2012)
YFZR105-A
SHO
Description
Shown in Gray Vinyl and Black Carbon
Fiber with Black Stitching
Top Front: Medium Slip Black
Top Rear: Medium Slip Silver
Front Collar: Carbon Red Vinyl
Center Band & Tail: Carbon Red Vinyl
Side & Back Rest: Smooth Black Vinyl
Stitch: Red Thread
FZS Series
YFZS101-B
FZR
Description
Shown in Black Gripper, Silver Carbon Fiber
and Vinyl wIth White Stitching
Part No.
AZ-SEWFZR-A
FZS
Part No.
AZ-SEWFZS-A
VXR Series
YVXR101-A
Top Front: Medium Slip Silver Vinyl
Top Rear: Medium Slip Black
Front Collar: Carbon Dark Blue Vinyl
Center Band & Tail: Carbon Dark
Blue Vinyl
Side & Back Rest: Smooth Black Vinyl
Stitch: Blue Thread
YVXR101-C
Top Front & Rear: Non Slip Black
Diamond Plate Vinyl
Front Collar: Smooth Grain Black Vinyl
Center Band & Tail: Smooth Grain
Black Vinyl
Side: Carbon Black
Back Rest: Bright Orange
Stitch: Orange Thread
©2012 Hot Products. All rights reserved.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Description
Shown in Black Gripper, Silver Carbon Fiber
and Black Vinyl with White Stitching
BODY
Front: Kevlar Black
Top 1: Medium Slip Silver
Top 2: Smooth Grain Red
Rear Top: Medium Slip Black
Rear Tail: Smooth Grain Red
Side: Carbon Black
Tail: Medium Slip Black
Rear Side: Carbon Dark Silver
Part No.
AZ-SEWFX1-A
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Top: Black Diamond Plate Non-Slip Vinyl
Front & Rear Side: Carbon Black Large
Spike: Smooth Light Green Vinyl
Rear: Black Ostrich
Stitch: Green Thread on Top
EXHAUST
FZR Series (09-11)
Description
FX-SHO Custom Designed Seat Cover
FZR Custom Designed Seat Cover
FZS Custom Designed Seat Cover
ENGINE/
GASKETS
PRE-COLORED HOT PRODUCTS
RECOMMENDED JETTRIM SEAT COVERS
HYDRO-TURF PREMIER
CUSTOM ORDER SEAT COVER
INATKE
SYSTEMS
Part No.
YFZR101
YFZR102
YFZ105
YFZS101
YFZS102
YSHO101
YVXR101
YAMAHA
4 STROKE
JETTRIM CUSTOM ORDER SEAT COVER
Description
Jettrim FZR (09-11) Spike Design Custom Seat Cover
Jettrim FZR (09-11) Retro Design Custom Seat Cover
Jettrim FZR (2012) Custom Design Seat Cover
Jettrim FZS Retro Design Custom Seat Cover
Jettrim FZS Spike Design Custom Seat Cover
Jettrim FX-SHO Custom Design Seat Cover
Jettrim VXR Custom Design Seat Cover
65