C.T.M. HS-666 Specifications

C.T.M. MOBILITY SCOOTER
6-Series Instruction Booklet
HS-665 / HS-666
HS-686
6-Series
Instruction Booklet
TABLE OF CONTENTS
INTRODUCTION ----------------------------------------------------------1
IMPORTANT PRECAUTIONS --------------------------------------------2
ELECTROMAGNETIC INTERFERENCE AND WARNINGS ------------3
IDENTIFICATION OF PARTS ---------------------------------------------5
OPERATING YOUR SCOOTER ------------------------------------------7
ASSEMBLING YOUR SCOOTER ----------------------------------------9
DISASSEMBLING YOUR SCOOTER -----------------------------------11
CHARGING THE BATTERIES ------------------------------------------13
CARE AND MAINTENANCE --------------------------------------------14
TROUBLESHOOTING --------------------------------------------------15
TECHNICAL SPECIFICATIONS ----------------------------------------17
6-Series
Instruction Booklet
INTRODUCTION
Thank you and congratulation on purchasing your new C.T.M. Mobility Scooter. It is
designed to provide you with transportation ability indoors and outdoors.
We pride ourselves on providing safe and comfortable products. Our goal is to ensure
your complete satisfaction with our product. We are certain that you will enjoy your
C.T.M. mobility scooter.
Please read and observe all warning and instruction provided in the owner's manual
before operating this scooter. Also, retain this booklet for future reference.
If you have any questions, you can contact:
C.T.M.HOMECARE PRODUCT, INC.
13815 Magnolia Ave. #B, Chino CA 91710
Toll Free : 1-866-466-8168 Tel : 909-590-1388 Fax : 909-590-3365
E-Mail : ctm@ctmhomecare.com http : //www.ctmhomecare.com
or your local dealer:
1
6-Series
Instruction Booklet
IMPORTANT PRECAUTIONS
•Only one person at a time could ride a C.T.M. Mobility Scooter.
•Maximum load is 160 kgs/ 350 pounds.
•Turn key off before getting on or off.
•Always drive carefully and be aware of others using the same area as yourself.
•Always use pedestrian crossings wherever possible. Take extreme care when crossing
roads.
•Do not drive on slopes exceeding a 12 degree and take extreme care when turning on
slope.
•Do not use full power when turning to sharp corner.
•Take great care and low speed when backing up, riding downhill, or on uneven surface,
and climbing curb.
•Scooter may not operate well in high humidity.
•If you are caught in rain, it is handy to carry a scooter canopy. It offers complete
protection for yourself scooter.
•Never put scooter in neutral when staying on slopes.
•Follow traffic laws when riding outside.
2
6-Series
Instruction Booklet
Electromagnetic Interference (EMI)
CAUTION: It is very important that you read this information regarding the possible
effects of Electromagnetic Interference on your motorized scooter.
Powered wheelchairs and motorized scooters may be susceptible to electromagnetic
interference (EMI), which is inccterfering electromagnetic energy (EM) emitted from sources
such a radio stations, TV stations, amateur radio (HAM) transmitters, two-way radios, and
cellular phones. The interference (from radio wave sources) can cause the motorized
scooter to release its brakes, move by itself, or move in unintended directions. It can also
permanently damage the motorized scooter control system. The intensity of the interfering
EM energy can be measured in volts per meter (V/m). Each motorized scooter can resist
EMI up to certain intensity. This is called its "immunity level." The higher the immunity
level, the greater the protection. At this time, current technology is capable of achieving
at least a 20 V/m immunity level, which would provide useful protection from the more
common sources of radiated EMI. This immunity level of this motorized scooter model
is not known.
There are a number of sources of relatively intense electromagnetic fields in the everyday
environment. Some of these sources are obvious and easy to avoid. Others are not
apparent and exposure is unavoidable. However, we believe that by following the
warnings listed below, your risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1.Hand-held portable transceivers (transmitters-receivers) with the antenna mounted
directly on the transmitting unit. Examples include: citizens band (CB) radios, alkie
talkie," security, fire, and police transceivers, cellular telephones, and other personal
communication devices.
Some cellular telephones and similar devices transmit signals while they
are ON, even when not being used;
2.Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances, and taxis. These usually have the antenna mounted on the outside of the
vehicle; and
3.Long-range transmitters and transceivers such as commercial broadcast transmitters
(radio and TV broadcast antenna towers) and amateur (HAM) radios.
Other types of hand-held devices, such as cordless phones, laptop computers,
AM/FM radios, TV sets, CD players, and cassette players, and small appliances
such as electric shavers and hair dryers, so far as we know, are not likely to
cause EMI problems to your motorized scooter.
3
6-Series
Instruction Booklet
Motorized Scooter Electromagnetic Interference:
Because EM energy rapidly becomes more intense as one moves closer to the transmitting
antenna (source), the EM fields from hand-held radio wave sources (transceivers) are of
special concern. It is possible to unintentionally bring high levels of EM energy very close to
the motorized scooter control system while using these devices. This can affect motorized
scooter movement and braking. Therefore, the warnings listed below are recommended to
prevent possible interference with the control system of the motorized scooter.
Warnings:
Electromagnetic interference (EMI) from sources such as radio and TV stations, amateur
radio (HAM) transmitters, two-way radios, and cellular phones can affect motorized scooters.
Following the warnings listed below should reduce the chance of unintended brake release
or motorized scooter movement which could result in serious injury.
1.Do not operate hand-held transceivers (transmitters-receivers), such as citizens band
(CB) radios, or turn ON personal communication devices, such as cellular phones, while
the motorized scooter is turned ON;
2.Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming
close to them;
3.If unintended movement or brake release occurs, turn the motorized scooter OFF as
soon as it is safe;
4.Be aware that adding accessories or components, or modifying the motorized scooter,
may make it more susceptible to EMI.
There is no easy way to evaluate their effect on the overall immunity of
the motorized scooter and
5.Report all incidents of unintended movement or brake release to the distributor listed
on the inside front cover of this manual. Note whether there is a source of EMI nearby.
Important Information:
1.20 volts per meter (V/m) is a generally achievable and useful immunity level against
EMI (as of May 1994). The higher the level, the greater the protection.
2.The immunity level of this motorized scooter model is 20 (V/m).
4
6-Series
Instruction Booklet
IDENTIFICATION OF PARTS
The C.T.M. Mobility Scooter is an indoor/outdoor scooter that provides transportation
for a disabled or elderly person.
Rearview Mirror
The full lighting system
consists of headlights,
taillights and both front
and rear turn signals.
Tall Back Luxury
Swivel Seat Sliding Adjustment
Thumb Lever
Flip-Up ArmrestsWidth Adjustable
Tiller Angle Adjustment
Seat Rotation Lever
Rear Bumper
Front Bumper
Rear Coil-over Suspension
Figure 1 - HS-686 Front View
Self-Diagnostic
Warning Light
Battery Gauge Indicator
High Speed
Speed Dial Knob
Horn Button
Low Speed
Left Turn Signal
Right Turn Signal
Headlight Button
Figure 2 - HS-686 Top Control Panel
5
6-Series
Instruction Booklet
Function of parts:
Thumb Levers :
Pushing right thumb lever moves scooter forward. Pushing the left thumb lever moves
scooter backward. Releasing both engages automatic brake.
Seat Adjustment :
Seat Control Slide : lift up lever under front edge of seat base to move forward and backward.
Seat Rotation Lever : push lever back to rotate seat; push forward to lock seat in position.
Tiller Angle Adjustment Lever :
Push lever down to adjust, release to lock Tiller Angle Adjustment in comfortable angle.
High/Lo Speed Switch :
When High/Lo Speed Switch is in High position, scooter performs in normal. If it is in the
Lo position, the scooter travels in half of normal speed which is convenient for side-walk
use.
Rear Cover :
Protects batteries from damage.
Anti-tip device :
Helps keep the scooter from tipping over.
Free-Wheeling Lever :
When lever is in N (Neutral) position, scooter can be moved without power.
When lever is in D (Drive) position, scooter can be driven. Normal position is D.
View of the Control Panel at top of steering column:
Self Diagnostic Warning Light:
Flashing indicates problems within scooter. See page 14 for more information.
Battery Gauge Indicator:
This light is yellow. Below it are three color ranges: red, yellow and green. When all lights
are on batteries are fully charged. When light is on, only in red, or red and yellow areas,
the batteries need to be recharged.
Batteries:
Two 12 volt sealed batteries.
Battery charger:
The battery charger is a 24 volt, 5 amp, constant current charger.
Accessories:
These can be ordered from your local distributor.
•Additional Mirror •Rear basket
•Storage cover
•Cane holder
6
6-Series
Instruction Booklet
OPERATING YOUR SCOOTER
•all electrical connections are firmly attached
•adjust seat height and location
•adjust tiller to comfortable position
1.Before operating your scooter, check the following:
•free-wheeling device on D
•speed dial is at the turtle picture.
2.Sit on scooter and turn on key, all battery gauge LED lights should be lighting the
green, yellow, and red color zones. The Self-Diagnostic Warning Light should not be
blinking.
3.When your hands rest comfortably on handlebars, the thumb levers should be within
easy reach. The right lever moves scooter forward, the left one moves it backward.
When you release both levers scooter stops.
4.Steer scooter by turning the whole tiller toward the way you want to go.
5.Practice driving where there is no obstacles. Start at the slowest speed and drive
forward and backward; make some turns. As you get more comfortable you can
increase speed by turning the speed dial toward picture of rabbit.
6.Keep in mind these rules:
•Release thumb levers and allow scooter to stop completely before changing from
forward to reverse, or reverse to forward.
•When turning to corner, swing front wheels widely for back wheels will turn more
tightly.
•Drive in low speeds when reversing, riding downhill, over ramps, and curb, or on
uneven surface.
•Ride the scooter only where it is safe for walking.
7.If the Power Reserve Indicator lights only in red or red and yellow zones, you should
plan to recharge batteries very soon.
8.If scooter stops, locate circuit breaker on rear unit. Push it DOWN and try driving again.
9.When you are finished riding, turn off the key before getting off.
10.If you are finished riding for the day, immediately recharge the batteries. See Charging
batteries, page 12.
7
6-Series
Instruction Booklet
Other operating information:
Hill climbing :
You may need to use a higher speed. Turn to lower speed before going downhill.
Curb climbing :
Approach slowly at right angles to the curb. Do not attempt greater than a 2" curb.
If Self-Diagnostic Warning Light starts to blink, identify the problem from chart on page
14 and take action.
If the scooter breaks down and must be moved, get off scooter, push engage Free
Wheeling Lever to N, push scooter to a safe location, and then move the lever back to D.
8
6-Series
Instruction Booklet
ASSEMBLING YOUR SCOOTER
No tools are necessary. A screwdriver is needed to adjust seat height after assembly.
To assemble C.T.M. Mobility Scooter you should have the three scooter parts : front.
section, rear section and seat. You will also need two batteries and a battery charger.
Follow these steps:
Use the Tiller Angle Adjustment Lever to move the Tiller Angle Adjustment up out of the
way.(See Fig. 3)
Figure 3
Connect front and rear sections by linking latching hook (A) to pin (B).(See Fig. 4)
Pluging the two wire connectors (C)between the front and rear sections.(See Fig. 5)
B
A
Figure 4
C
Figure 5
Place batteries, one on each side of the seat post.(See Fig. 6)
Attach the power plugs (D).(See Fig. 7)
D
Figure 6
Figure 7
9
6-Series
Instruction Booklet
Place battery cover over batteries.(See Fig. 8)
Loosen Seat Rotation Lever (E) counterclockwise. Place seat on seat post. Tighten Lever
(E) again by turning clockwise. Lock Seat Control Lever on bottom of seat before sitting
down.(See Fig. 9)
E
Figure 8
Figure 9
Attach Front Basket. Adjust Seat Height: If the seat height is not correct, remove seat
from scooter. Use a screwdriver to raise or lower the seat. Remount seat on seat post.
Adjust Tiller Angle position: Use the Tiller Angle Adjustment Lever to adjust the tiller to
a comfortable position.
10
6-Series
Instruction Booklet
DISASSEMBLING YOUR SCOOTER
Taking apart your scooter enables you to save space when keeping it in storage
or to carry it along in your vehicle when going away from home. Having scooter
disassembled is easier than ever since no tools are required.
Please follow these steps :
Seat is removable by releasing the Seat Adjusting Lever (F) and then lift off. (See Fig. 10)
Rear Shroud Cover is removable by lifting up. (See Fig. 11)
F
Figure 10
Figure 11
Then disconnect Rear Turnsignal Wire. (See Fig. 12) and remove front Battery Cover.
(See Fig. 13)
Figure 12
Figure 13
Unplug Battery Wire (See Fig. 14) and untie Battery Fixing Velcro to remove Batteries.
(See Fig. 15)
Figure 14
Figure 15
11
6-Series
Instruction Booklet
Rear Shroud is removable by lifting the Rear Shroud up. (See Fig. 16)
Disconnect Wire Harness. (See Fig. 17)
Figure 16
Figure 17
Release two Guide Pins to separate Front and Rear Sections. (See Fig. 18)
With one hand on rear frame and other on seat post as handheld, detach Front and Rear
Sections. (See Fig. 19)
Figure 18
Figure 19
By removing the front basket and adjusting the tiller down by using the Tiller Angle
Adjustment Lever you should be able to place all parts in the trunk and part of the Rear
Seat.(See Fig. 20 & 21 & 22)
Figure 20
Figure 21
Figure 22
12
6-Series
Instruction Booklet
CHARGING THE BATTERIES
Batteries must be charged before using the scooter for the first time and should be
recharged after each day use. You will need the scooter and the battery charger.
Each country may supply different
charger. The charging procedure
may be different from below.
If you require more details, please
contact your authorized dealer.
Be sure the scooter key is in the
OFF position
1.Insert battery charger cord into the charger connector on the charger output. Refer to
above figure for correct position
2.Plug the other end of the battery charger cable into a standard electrical outlet.
3.Turn the power on. Normally, The LED (Power) Light will turn on when electric current
passes.
4.Charging starts. During charging, LED (Charge) will indicate orange light, when it turns
to green light, that means well-charged.
5.LED indication
•LED(POWER) - GREEN LIGHT ON : Power On.
•LED(CHARGE) - ORANGE LIGHT ON : Charging / GREEN LIGHT ON : Fully Charged
6.Charger Trouble Shooting
(A)If LED (POWER) light is off
•Check the input voltage (115V/230V) is the same as you adjust.
•If light is still off, please check and repair the battery charger.
(B)If LED (CHARGE) light is off
•Check to see clips connection is correct.
•If the battery is fully charged, the LED (CHARGE) light will be off.
•If light is still off, the battery may be defective.
(C)If ORANGE light can turn to GREEN
•The battery can not be charged. Please check and recover it.
(D)If ORANGE light turns to GREEN immediately
•Check to see the battery is fully charged, if not, The battery may be defective
Check and recover it.
The time needed to recharge will vary depending on the depletion of the
batteries. Charging for longer than necessary will not harm the batteries.
They can not be overcharged.
13
6-Series
Instruction Booklet
CARE AND MAINTENANCE
•Cleaning your scooter
Your scooter can be cleaned with a dry cloth. Do not use water because of electrical
connections.
•Maintaining your scooter
All maintenance and repair of your scooter should be done by an authorized dealer.
•Storing your scooter
Between uses, your scooter is best stored at room temperature in a dry area.
14
6-Series
Instruction Booklet
TROUBLESHOOTING
Here are some suggestions about solving problems you may have with your scooter.
There is a Self-Diagnostic Warning Light on the Control Panel. To check the SelfDiagnostic Warning Light, turn on the key and count the number of blinks on the
Warning Light.
Number of
Flashes
Problem
1
Battery needs recharging
Recharge the batteries soon.
2
Battery voltage too low
to operate scooter
Must recharge before using.
Check battery condition and
connections.
3
Battery voltage too high
Check battery condition and
connections. Contact your authorized
dealer to check your battery charger.
4
Short in motor
Contact your authorized dealer.
5
Brake malfunction
Contact your authorized dealer.
6
Thumb lever not in
neutral
Contact your authorized dealer.
7
Thumb lever malfunction
Contact your authorized dealer.
8
Motor problems
Contact your authorized dealer.
9
Other internal errors
Contact your authorized dealer.
Solution
During charging, if light on the charger does not turn to green: Contact your authorized
dealer.
Scooter will not move when key is turned on :
1.Check Power Reserve Indicator on control panel. It should be light in the green, yellow,
and red zones.
2.Check Self-Diagnostic Warning Light. It should be steady. If it is flashing, see above
chart for problem identification.
3.Check all electrical connections to be sure they are tight.
4.If none of above correct the problem, contact your authorized dealer.
15
6-Series
Instruction Booklet
Summay:
Avoid sources of Electromagnetic Interference because they may affect the scooter.
Assembly and disassembly :
Assemble completely before riding.
Always disassemble before transporting in a car.
Charge batteries after each use.
Safety Rules :
•Turn key OFF before getting on or off.
•Allow scooter to stop before changing from forward to reverse.
•Use low speeds when backing up riding downhill, or on uneven surfaces, and climbing
curd.
•Do not turn suddenly at high speed.
•Do not use on slopes of 12 degree
•Avoid uneven ground, tall grass, or slippery surfaces.
•Operate only where it is safe to walk.
•Follow all traffic laws.
16
6-Series
Instruction Booklet
SPECIFICATION
SPECIFICATIONS
HS-665
HS-666
HS-686
Overall Length
47.8"
47.8"
52.8"
Overall Width
24.6"
24.6"
24.6"
Overall Height
39"
39.5"
39.4"
Wheels: Front
10"
10"
11"
Wheels: Rear
11"
11"
11"
Weight w/ Batteries
190 lbs
192 Ibs.
210 lbs
Max. Speed
5 mph
5 mph
5 mph
Weight Capacity
350 lbs
350 lbs
350 lbs
2"
2"
2"
12 degree
12 degree
12 degree
Curb Climbing
2"
2"
2"
Turning Radius
41"
41"
56.3"
Rear
Rear Wheels
Rear
Electro-Mechanical
Electro-Mechanical
Electro-Mechanical
Ground Clearance
Grade Climbable
Suspension
Brake
Seat Type
Tall Back Luxury SwivelSeat-Sliding Adjustment
Seat Width
19"
19"
19"
Motor Size
500W 3400r.p.m
500W 3400r.p.m
500W 3400r.p.m
(2) 12V . 36Ah
(2) 12V.36Ah
(2) 12V . 36Ah
Battery Weight
55 lbs
55 lbs
55 lbs
Travel Range
14.7 Miles
14.7 Miles
15 Miles
5A Off Board
5A Off Board
5A Off Board
Battery Size
Battery Charger
Electronics
On/Off Key Switch, Battery Level Indicator,
Speed Control Knob
*Subject to change without notice.
17
(Issue A 07/02/2014 )