Makita RT0700C Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Trimmer
RT0700C
011833
DOUBLE INSULATION
IMPORTANT: Read Before Using.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
RT0700C
Collet chuck capacity
6 mm, 8 mm, 1/4" or 3/8"
No load speed (min-1)
10,000 - 30,000
Overall length
200 mm
Net weight
1.8 kg
Safety class
/II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5
ENG900-1
Symbols
Vibration
The vibration total value (tri-axial
determined according to EN60745:
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
・ Read instruction manual.
・
DOUBLE INSULATION
・
Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic
equipment
and
its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an
environmentally
compatible
recycling facility.
vector
sum)
Work mode : rotation without load
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
Work mode : cutting grooves in MDF
Vibration emission (ah) : 3.5 m/s2
Uncertainty (K) : 1.5 m/s2
ENG901-1
•
•
ENE010-1
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
•
ENF002-1
•
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-14
For European countries only
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN60745:
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Trimmer
Model No./ Type: RT0700C
are of series production and
Sound pressure level (LpA) : 82 dB(A)
Sound power level (LWA) : 93 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
2
electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
17. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, MK15 8JD, England
6.
14.10.2010
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
GEA005-3
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
3
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
21. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Service
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
26. Follow instruction for lubricating and
changing accessories.
27. Keep handles dry, clean and free from oil and
grease.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
GEB019-4
TRIMMER SAFETY WARNINGS
1.
2.
to loss of control.
Wear hearing protection during extended
period of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or
damaged bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the
workpiece before the switch is turned on.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate improperly
installed bit.
Be careful of the bit rotating direction and the
feed direction.
Do not leave the tool running. Operate the tool
only when hand-held.
Always switch off and wait for the bit to come
to a complete stop before removing the tool
from workpiece.
Do not touch the bit immediately after
operation; it may be extremely hot and could
burn your skin.
Do not smear the tool base carelessly with
thinner, gasoline, oil or the like. They may
cause cracks in the tool base.
Use bits of the correct shank diameter suitable
for the speed of the tool.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
Always use the correct dust mask/respirator
for the material and application you are
working with.
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable
platform.Holding the work by your hand or
against the body leaves it unstable and may lead
4
Speed adjusting dial
FUNCTIONAL DESCRIPTION
•
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
1. Speed adjusting
dial
1
Adjusting bit protrusion
1
2
3
1. Bit protrusion
2. Tool base
3. Scale
4. Locking lever
5. Adjusting screw
6. Hex nut
011835
The tool speed can be changed by turning the speed
adjusting dial to a given number setting from 1 to 6.
Higher speed is obtained when the dial is turned in the
direction of number 6. And lower speed is obtained when it
is turned in the direction of number 1.
This allows the ideal speed to be selected for optimum
material processing, i.e. the speed can be correctly
adjusted to suit the material and bit diameter.
Refer to the table for the relationship between the number
settings on the dial and the approximate tool speed.
5
4
6
011834
To adjust the bit protrusion, loosen the locking lever and
move the tool base up or down as desired by turning the
adjusting screw. After adjusting, tighten the locking lever
firmly to secure the tool base.
NOTE:
•
When the tool is not secured even if the locking
lever is tightened, tighten the hex nut and then
tighten the locking lever.
Switch action
•
•
2
min-1
1
2
3
4
5
6
10,000
12,000
17,000
22,000
27,000
30,000
011932
1. Switch
2. OFF (O) side
3. ON ( I ) side
1
Number
3
011836
CAUTION:
Before plugging in the tool, always check to see
that the tool is switched off.
To start the tool, press the "ON ( I )" side of the switch.
To stop the tool, press the "OFF (O)" side of the switch.
•
Electronic function
The tool equipped with electronic function are easy to
operate because of the following features.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start
Soft-start feature minimizes start-up shock, and makes
the tool start smoothly.
5
CAUTION:
If the tool is operated continuously at low speeds
for a long time, the motor will get overloaded,
resulting in tool malfunction.
The speed adjusting dial can be turned only as far
as 6 and back to 1. Do not force it past 6 or 1, or
the speed adjusting function may no longer work.
OPERATION
ASSEMBLY
For the trimmer base
•
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing trimmer bit
1
2
3
1. Tighten
2. Loosen
3. Hold
3
2
1
1. Dust nozzle
2. Thumb screw
3. Trimmer base
011837
3
1
1. Tighten
2. Loosen
3. Shaft lock
011989
WARNING:
Before using the tool with the trimmer base, always
install the dust nozzle on the trimmer base.
Set the tool base on the workpiece to be cut without the
bit making any contact. Then turn the tool on and wait
until the bit attains full speed. Move the tool forward over
the workpiece surface, keeping the tool base flush and
advancing smoothly until the cutting is complete.
When doing edge cutting, the workpiece surface should
be on the left side of the bit in the feed direction.
2
•
011987
CAUTION:
Do not tighten the collet nut without inserting a bit,
or the collet cone will break.
•
Use only the wrenches provided with the tool.
Insert the bit all the way into the collet cone and tighten
the collet nut securely with the two wrenches or by
pressing the shaft lock and using the provided wrench.
To remove the bit, follow the installation procedure in
reverse.
•
2
1
4
4
2
3
1. Workpiece
2. Bit revolving direction
3. View from the top of the tool
4. Feed direction
001984
NOTE:
•
Moving the tool forward too fast may cause a poor
quality of cut, or damage to the bit or motor. Moving
the tool forward too slowly may burn and mar the cut.
The proper feed rate will depend on the bit size, the
kind of workpiece and depth of cut. Before beginning
the cut on the actual workpiece, it is advisable to
make a sample cut on a piece of scrap lumber. This
will show exactly how the cut will look as well as
enable you to check dimensions.
6
When using the trimmer shoe, the straight guide or
the trimmer guide, be sure to keep it on the right
side in the feed direction. This will help to keep it
flush with the side of the workpiece.
•
2
3
1
7
3
1. Feed direction
2. Bit revolving
direction
3. Workpiece
4. Straight guide
5
4
10mm (3/8")
1. Straight bit
2. Base
3. Templet
4. Distance (X)
5. Workpiece
6. Templet guide
10
7. Base protector
011982
NOTE:
•
The workpiece will be cut a slightly different size
from the templet. Allow for the distance (X)
between the router bit and the outside of the
templet guide. The distance (X) can be calculated
by using the following equation:
Distance (X) = (outside diameter of the templet guide router bit diameter) / 2
4
001985
•
6
1
2
CAUTION:
Since excessive cutting may cause overload of the
motor or difficulty in controlling the tool, the depth
of cut should not be more than 3 mm at a pass
when cutting grooves. When you wish to cut
grooves more than 3 mm deep, make several
passes with progressively deeper bit settings.
Straight guide (optional accessory)
Templet guide (optional accessory)
011840
The straight guide is effectively used for straight cuts
when chamfering or grooving.
011838
The templet guide provides a sleeve through which the bit
passes, allowing use of the trimmer with templet patterns.
Loosen the screws and remove the base protector.
Place the templet guide on the base and replace the
base protector. Then secure the base protector by
tightening the screws.
1
2
3
1. Bolt
2. Guide plate
3. Straight guide
4. Wing nut
1
2
3
4
1. Base protector
2. Screws
3. Screwdriver
001990
Attach the guide plate to the straight guide with the bolt
and the wing nut.
2
1. Clamp screw (A)
2. Straight guide
3. Wing nut
4. Base
1
2
011839
Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.
3
4
011841
Attach the straight guide with the clamp screw (A).
Loosen the wing nut on the straight guide and adjust the
7
distance between the bit and the straight guide. At the
desired distance, tighten the wing nut securely.
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
If the distance (A) between the side of the workpiece and
the cutting position is too wide for the straight guide, or if
the side of the workpiece is not straight, the straight guide
cannot be used. In this case, firmly clamp a straight board
to the workpiece and use it as a guide against the trimmer
base. Feed the tool in the direction of the arrow.
NOTE:
•
Circles between 172 mm and 186 mm in radius
cannot be cut using this guide.
1. Nail
2. Center hole
3. Straight guide
1
2
3
A
011843
Align the center hole in the straight guide with the center
of the circle to be cut. Drive a nail less than 6 mm in
diameter into the center hole to secure the straight guide.
Pivot the tool around the nail in clockwise direction.
Trimmer guide (optional accessory)
011842
Circular work
1. Wing nut
2. Guide plate
3. Straight guide
4. Center hole
5. Bolt
1
4
2
3
5
011844
Trimming, curved cuts in veneers for furniture and the
like can be done easily with the trimmer guide. The
guide roller rides the curve and assures a fine cut.
001993
Circular work may be accomplished if you assemble the
straight guide and guide plate as shown in the figures.
Min. and max. radius of circles to be cut (distance
between the center of circle and the center of bit) are as
follows:
Min.: 70 mm
Max.: 221 mm
For cutting circles between 70 mm and 121 mm in radius.
For cutting circles between 121 mm and 221 mm in
radius.
4
5
2
3
4
011845
Install the trimmer guide on the tool base with the clamp
screw (A). Loosen the clamp screw (B) and adjust the
distance between the bit and the trimmer guide by
turning the adjusting screw (1 mm per turn). At the
desired distance, tighten the clamp screw (B) to secure
the trimmer guide in place.
1. Wing nut
2. Guide plate
3. Straight guide
4. Center hole
5. Bolt
1
1. Clamp screw (A)
2. Adjusting screw
3. Clamp screw (B)
4. Trimmer guide
1
2
3
001994
8
1. Workpiece
2. Bit
3. Guide roller
2
1. Base protector
2. Screw
1
3
1
001998
When cutting, move the tool with the guide roller riding
the side of the workpiece.
Tilt base (optional accessory)
Tilt base (optional
chamfering.
accessory)
is
convenient
for
2
1
1. Clamping
screws
011994
And then mount the base protector on the trimmer base.
Offset base (optional accessory)
011993
Place the tool onto the tilt base and close the locking
lever at the desired protrusion of the bit. For desired
angle, tighten the clamping screws on its sides.
Firmly clamp a straight board to the workpiece and use it
as a guide against the tilt base. Feed the tool in the
direction of the arrow.
Base protector removed from the tilt base (optional
accessory)
Mounting the base protector which has been removed
from the tilt base on the trimmer base allows the change
of the trimmer base from the round base to a square
base.
For another application, remove the base protector from
the tilt base by loosening and removing four screws.
012085
(1)
Offset base (optional accessory) is convenient
for work in a tight area such as a corner.
1. Pulley
2. Collet nut
3. Collet cone
3
1
2
011858
Before installing the tool on the offset base, remove the
collet nut and collet cone by loosening the collet nut.
1. Wrench
2. Pulley
3. Shaft lock
1
2
011985
9
3
Install the pulley on the tool by pressing the shaft lock
and firmly tightening the pulley with a wrench.
1. Wrench
2. Hex wrench
3. Bit
1
1. Collet nut
2. Collet cone
2
2
1
3
011992
To install the bit, fall the tool with the offset base on its side.
Insert the hex wrench into the hole in the offset base.
With the hex wrench held in that position, insert the bit
into the collet cone on the shaft of the offset base from
the opposite side and tighten the collet nut firmly with a
wrench.
To remove the bit at replacement, follow the installation
procedure in reverse.
(2) Offset base (optional accessory) can also be
used with a trimmer base and a grip
attachment (optional accessory) for more
stability.
011859
Place the collet cone and screw the collet nut on the
offset base as shown in the figure.
011860
1
2
1. Screws
2. Offset base
plate
3. Upper section of
the offset base
1
Mount the tool on the offset base
1. Pulley
2. Belt
2
011861
Put an end of the belt over the pulley using a screwdriver
and make sure that its entire belt width fits over the
pulley completely.
3
1. Locking lever
2. Offset base
011934
Loosen the screws and remove the upper section from
the offset base. Put aside the upper section of the offset
base.
1
2
1
011862
Secure it with a locking lever on the offset base.
4
2
3
011935
10
1. Bar type grip
(optional accessory)
2. Grip attachment
(optional accessory)
3. Offset base plate
4. Trimmer base
assembly (optional
accessory)
Mount the trimmer base with four screws and the grip
attachment (optional accessory) with two screws on the
offset base plate.
Screw a bar type grip (optional accessory) onto the grip
attachment.
1
1. Screw
2. Knob
1
2
1. Screw
2. Knob type grip
3. Offset base plate
2
011856
To use the bar type grip (optional accessory), loosen the
screw and remove the knob type grip.
3
011984
In another way of use, the knob type grip which is
removed from a plunge base (optional accessory) can
be installed on the grip attachment. To install the knob
type grip, place it on the grip attachment and secure it
with a screw.
1
1. Bar type grip
(optional
accessory)
011857
And then screw the bar type grip on the base.
Adjusting the depth of cut when using the plunge
base (optional accessory)
011986
1
When using as a router only with a plunge
base (optional accessory)
•
1. Adjusting knob
2. Lock lever
3. Depth pointer
4. Stopper pole
setting nut
5. Fast-feed button
6. Stopper pole
7. Stopper block
8. Adjusting bolt
2
CAUTION:
When using as a router, hold the tool firmly with
both hands.
3
4
5
6
1. Plunge base
2. Grip
7
2
8
011983
Place the tool on a flat surface. Loosen the lock lever and
lower the tool body until the bit just touches the flat surface.
Tighten the lock lever to lock the tool body.
Turn the stopper pole setting nut counterclockwise. Lower
the stopper pole until it makes contact with the adjusting
bolt. Align the depth pointer with the "0" graduation. The
depth of cut is indicated on the scale by the depth pointer.
While pressing the fast-feed button, raise the stopper pole
until the desired depth of cut is obtained. Minute depth
adjustments can be obtained by turning the adjusting knob
(1 mm per turn).
By turning the stopper pole setting nut clockwise, you can
1
011855
To use the tool as a router, install the tool on a plunge
base (optional accessory) by pressing it down fully.
Either knob type grip or bar type grip (optional
accessory) can be used according to your work.
11
fasten the stopper pole firmly.
Now, your predetermined depth of cut can be obtained by
loosening the lock lever and then lowering the tool body
until the stopper pole makes contact with the adjusting hex
bolt of the stopper block.
Always firmly hold the tool by both grip during operation.
Set the tool base on the workpiece to be cut without the
bit making any contact. Then turn the tool on and wait
until the bit attains full speed. Lower the tool body and
move the tool forward over the workpiece surface,
keeping the tool base flush and advancing smoothly until
the cutting is complete.
When doing edge cutting, the workpiece surface should
be on the left side of the bit in the feed direction.
1
2
3
4
8
7
4
5
1. Bolt
2. Guide holder
3. Wing nut
4. Bolt
5. Wing nut
6. Guide plate
7. Straight guide
8. Wing bolts
2
1
6
4
2
3
011988
Install the straight guide on the guide holder (optional
accessory) with the wing nut.
Insert the guide holder into the holes in the plunge base
and tighten the wing bolts. To adjust the distance
between the bit and the straight guide, loosen the wing
nut. At the desired distance, tighten the wing nut to
secure the straight guide in place.
1. Workpiece
2. Bit revolving direction
3. View from the top of the tool
4. Feed direction
001984
NOTE:
•
Moving the tool forward too fast may cause a poor
quality of cut, or damage to the bit or motor. Moving
the tool forward too slowly may burn and mar the cut.
The proper feed rate will depend on the bit size, the
kind of workpiece and depth of cut. Before beginning
the cut on the actual workpiece, it is advisable to
make a sample cut on a piece of scrap lumber. This
will show exactly how the cut will look as well as
enable you to check dimensions.
•
When using the straight guide, be sure to install it
on the right side in the feed direction. This will help
to keep it flush with the side of the workpiece.
2
3
1
Straight guide (optional accessory)
011848
The straight guide is effectively used for straight cuts
when chamfering or grooving.
1. Feed direction
2. Bit revolving
direction
3. Workpiece
4. Straight guide
1. Guide bar
2. Wing bolt
3. Straight guide
4
1
001985
2
3
011849
Straight guide when using as a router (needed
to use with guide holder (optional accessory))
To install the straight guide, insert the guide bars into the
holes in the plunge base. Adjust the distance between the
bit and the straight guide. At the desired distance, tighten
The straight guide is effectively used for straight cuts
when chamfering or grooving.
12
the wing bolts to secure the straight guide in place.
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
1
1. Bit
2. Base
3. Templet
4. Workpiece
5. Distance (X)
6. Outside
diameter of the
templet guide
7. Templet guide
7
2
A
3
4
5
6
003695
NOTE:
•
The workpiece will be cut a slightly different size
from the templet. Allow for the distance (X)
between the bit and the outside of the templet
guide. The distance (X) can be calculated by using
the following equation:
Distance (X) = (outside diameter of the templet
guide - bit diameter) / 2
011850
If the distance (A) between the side of the workpiece and
the cutting position is too wide for the straight guide, or if
the side of the workpiece is not straight, the straight guide
cannot be used. In this case, firmly clamp a straight board
to the workpiece and use it as a guide against the router
base. Feed the tool in the direction of the arrow.
Dust nozzle sets
Templet guide (optional accessory)
For the trimmer base
3
011851
The templet guide provides a sleeve through which the
bit passes, allowing use of the tool with templet patterns.
To install the templet guide, loosen the screws on the
tool base, insert the templet guide and then tighten the
screws.
1
2
1
1. Dust nozzle
2. Thumb screw
3. Trimmer base
1. Screw
2. Base
3. Templet
011989
3
011852
Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.
13
2
For the plunge base (optional accessory)
MAINTENANCE
•
•
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
Replacing carbon brushes
1
1. Limit mark
2
1. Dust nozzle
2. Thumb screw
1
011853
Use the dust nozzle for dust extraction. Install the dust
nozzle on the tool base using the thumb screw so that
protrusion on the dust nozzle fit to the notch in the tool
base.
Then connect a vacuum cleaner to the dust nozzle.
001145
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
1. Screwdriver
2. Brush holder
cap
1
2
011854
011846
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
14
Trimmer bits
OPTIONAL ACCESSORIES
Straight bit
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Straight & groove forming bits
•
Edge forming bits
•
Laminate trimming bits
•
Straight guide assembly
•
Trimmer guide assembly
•
Trimmer base assembly
•
Tilt base assembly
•
Plunge base assembly
•
Offset base assembly
•
Templet guide
•
Collet cone 6 mm
•
Collet cone 6.35 mm (1/4")
•
Collet cone 8 mm
•
Collet cone 9.53 mm (3/8")
•
Wrench 13
•
Wrench 22
•
005116
mm
20
20E
8
8
8E
6
6E
D
6
1/4"
8
6
1/4"
6
1/4"
A
L1
20
L2
50
15
60
25
8
50
18
6
50
18
011929
"U"Grooving bit
R
005117
mm
D
6
6
6E
1/4"
A
L1
L2
R
6
60
28
3
006486
"V"Grooving bit
005118
mm
D
A
L1
L2
1/4"
20
50
15
006454
15
90
Drill point flush trimming bit
Chamfering bit
005120
8
6
6E
005126
D
8
6
1/4"
A
8
L1
60
L2
20
mm
L3
35
6
60
18
28
mm
011930
D
A
L1
L2
L3
6
23
6
20
46
11
6
50
13
5
6
20
45
49
14
2
60
30
006462
Drill point double flush trimming bit
Cove beading bit
005121
005129
8
6
6E
D
8
6
1/4"
A
8
L1
80
L2
95
L3
20
mm
L4
25
6
70
40
12
14
mm
D
011931
A
L1
L2
6
20
43
8
R
4
6
25
48
13
8
006464
Corner rounding bit
Ball bearing flush trimming bit
005125
005130
mm
D
8R
6
8RE
1/4"
4R
6
4RE
1/4"
mm
A1
A2
L1
L2
L3
R
D
A
L1
L2
25
9
48
13
5
8
6
1/4"
10
50
20
20
8
45
10
4
006465
4
006489
16
Ball bearing corner rounding bit
Ball bearing cove beading bit
005131
005134
mm
R
D
6
A1
15
A2
8
L1
37
L2
7
L3
3.5
6
21
21
8
8
40
10
3.5
3
6
40
10
3.5
6
1/4"
A1
A2
A3
A4
L1
L2
L3
mm
R
6
20
18
12
8
40
10
5.5
3
6
26
22
12
8
42
12
5
5
D
006466
006469
Ball bearing chamfering bit
Ball bearing roman ogee bit
005132
005135
mm
D
6
1/4"
6
A1
A2
L1
L2
26
8
42
12
8
20
45
11
41
60
005133
L1
L2
L3
mm
R
12
A3
8
40
10
5.5
4
12
8
42
12
4.5
7
A2
6
26
6
20
6
26
A2
L2
L3
8
L1
40
10
8
42
12
mm
R2
4.5
R1
2.5
4.5
4.5
3
6
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Ball bearing beading bit
A1
20
A1
006470
006467
D
6
D
006468
17
18
19
Makita Corporation
Anjo, Aichi, Japan
885025A229
20
www.makita.com