Radio Shack CD-8150 Owner`s manual

42-5071.fm Page 1 Thursday, August 12, 1999 10:45 AM
Cat. No. 42-5071
OWNER’S MANUAL
Please read before using this equipment.
CD-8150
5-Disc Compact Disc Changer
42-5071.fm Page 2 Thursday, August 12, 1999 10:45 AM
FEATURES
Your Optimus CD-8150 5-Disc Compact Disc Changer holds up to five
CDs. Its automatic disc loading system lets you select more music for
continuous play and gives you musical
variety without having to continually
remove and load discs.
The CD-8150’s advanced design
makes this CD changer simple to operate. It has these great features:
Four-Times Oversampling with Digital Filtering — improves the sound of
CDs by multiplying the standard 44.1
kHz sampling rate by four and using a
digital filter to reduce or eliminate
high-frequency distortion.
1-Bit DAC — uses the latest in digitalto-analog conversion circuitry to accurately reproduce all sound levels with
virtually no distortion.
Sequence Programming — lets you
program up to 32 selections to play in
any order you choose.
Intro Scan — helps you locate a desired track by playing the first 10 seconds of each track on the current CD.
You can also change the length of the
intro play time.
Remote Control — lets you control
the CD changer from a distance.
Repeat Play — lets you automatically
repeat a single track, multiple CDs, or
a series of programmed tracks.
Shuffle Play — randomly selects
tracks on loaded CDs and plays them.
Tri-Spot Pickup Servo System —
helps ensure perfect tracking of your
CDs.
5- or 3-Inch CD Compatible æ lets
you play 5- or 3-inch CDs.
Note: The remote control requires two
AA batteries.
Audible Search — helps you locate a
section of music by playing the CD
rapidly in either direction.
We recommend you record the CD
changer’s serial number here. The
number is on the back panel.
Automatic Search Music System
(ASMS) — lets you quickly move to
any track on a CD.
Serial Number: __________________
© 1997 Tandy Corporation.
All Rights Reserved.
RadioShack and Optimus are registered trademarks used by Tandy Corporation.
2
42-5071.fm Page 3 Thursday, August 12, 1999 10:45 AM
Important: Most material on compact
discs is copyrighted. Unauthorized duplication of copyrighted material is a
violation of the copyright laws of most
countries and such duplication may
result in fines and/or imprisonment.
Note, however, that in the United
States, it is not a violation of U.S.
copyright laws for a consumer to use
an audio recording device to duplicate
musical recordings for noncommercial (personal) use.
Warning: To prevent fire or shock
hazard, do not expose this product
to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
CDs that you can play on this changer
have this mark on them:
This symbol is intended to alert you
to the presence of uninsulated dangerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
Warnings:
• This unit employs a laser. Because of possible eye injury, only
a qualified service person should
remove the cover or attempt to
service this device.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are included in the literature accompanying this product.
• Use of controls or adjustments or
performance of procedures other
than those specified herein may
result in hazardous radiation exposure.
3
42-5071.fm Page 4 Thursday, August 12, 1999 10:45 AM
IMPORTANT SAFETY INSTRUCTIONS
Careful attention is devoted to quality
standards in the manufacture of your
CD changer, and safety is a major factor in its design. However, safety is
also your responsibility.
mended by the manufacturer or sold
with the product. Follow the manufacturer's instructions for mounting, and
use a recommended mounting accessory.
This section lists important information
that will help you properly use and enjoy your CD changer and accessories.
Read all the included safety and operating instructions before using your
CD changer. Follow them closely, and
retain them for future reference.
Carts — Move the product on a cart carefully.
Quick stops, excessive
force, and uneven surfaces may cause the
product/cart to overturn.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
Cleaning — Unplug this product from
the wall outlet before cleaning. Use
only a damp cloth for cleaning. Do not
use liquid or aerosol cleaners.
Attachments — Do not use attachments/accessories not recommended
by the product manufacturer, as they
might create a hazard.
Water and Moisture — Do not use
this product near water (for example,
near a bathtub, washbowl, kitchen
sink, or laundry tub; in a wet basement; or near a swimming pool).
Accessories — Do not place this
product on an unstable cart, stand, tripod, bracket, or table. The product
may fall, causing serious injury to a
child or adult, and serious damage to
the product. Use only with a cart,
stand, tripod, bracket, or table recom4
Ventilation — Slots and openings in
the cabinet provide ventilation, ensure
reliable operation, and protect from
overheating. Do not block or cover
these openings, and do not place the
product on a bed, sofa, rug, or other
similar surface. Do not place the product in a built-in bookcase or rack unless it provides proper ventilation as
specified by the manufacturer.
Power Sources — Operate this product using only the power source indicated on its marking label. If you are
not sure of your home's power type,
consult your product dealer or local
power company.
42-5071.fm Page 5 Thursday, August 12, 1999 10:45 AM
Polarization — This product is
equipped with a polarized AC line plug
(a plug having one blade wider than
the other). This plug will fit in the power outlet only one way. This is a safety
feature. If you cannot insert the plug
fully into the outlet, try reversing the
plug. If the plug still doesn't fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug. If you
need an extension, use a polarized
cord.
Power-Cord Protection — Route
power-supply cords so they are not
likely to be walked on or pinched by
items placed on or against them, paying particular attention to cords at
plugs, convenience receptacles, and
the point where they exit from the
product.
Nonuse Periods — Unplug the CD
changer’s power cord when you will
not use it for extended periods.
Lightning — For added protection for
this product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product due to
lightning and power-line surges.
Overloading — Do not overload wall
outlets, extension cords, or integral
convenience receptacles, as this can
result in a risk of fire or electric shock.
Objects and Liquids — Never push
objects of any kind into this product
through openings, as they may touch
dangerous voltage points or short out
parts that could result in a fire or electric shock. Never spill liquid of any
kind on the product.
Servicing — Do not attempt to service this product yourself, as opening
or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
Damage Requiring Service — Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
• When the power-supply cord or
plug is damaged.
• If liquid has been spilled or objects
have fallen into the product.
• If the product has been exposed
to rain or water.
• If the product does not operate
normally by following the operating instructions. Adjust only those
controls that are covered by the
operating instructions, as an improper adjustment of other controls may result in damage and
will often require extensive work
by a qualified technician to restore
the product to normal operation.
• If the product has been dropped
or damaged in any way.
5
42-5071.fm Page 6 Thursday, August 12, 1999 10:45 AM
• When the product exhibits a distinct change in performance.
Replacement Parts — When replacement parts are required, be sure
the service technician uses replacement parts specified by the manufacturer or having the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric
shock, or other hazards.
Safety Check — Upon completion of
service or repairs to this product, ask
the service technician to perform safety checks to determine that the product is in proper operating condition.
Wall or Ceiling Mount — The product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
Heat — The product should be situated away from heat sources such as
radiators, heat registers, stoves, or
other products (including amplifiers)
that produce heat.
6
42-5071.fm Page 7 Thursday, August 12, 1999 10:45 AM
CONTENTS
Preparation ...........................................................................................................
Connecting the CD Changer ...........................................................................
Using the Remote Control ...............................................................................
Installing Batteries ....................................................................................
Using the Remote .....................................................................................
8
8
8
8
9
Operation ............................................................................................................
Loading CDs .................................................................................................
Playing CDs ..................................................................................................
Selecting a CD ..............................................................................................
Selecting a Track ..........................................................................................
Changing CDs During Playback ...................................................................
10
10
10
12
12
13
Special Features ................................................................................................
Audible Search ..............................................................................................
Repeat Play ..................................................................................................
Shuffle Play ...................................................................................................
Intro Scan ......................................................................................................
Playing a Sequence of Tracks ......................................................................
Checking/Changing the Programmed Sequence ...................................
Adding to the Programmed Sequence ...................................................
Erasing a Programmed Sequence .........................................................
14
14
14
15
15
16
17
17
17
Troubleshooting ................................................................................................ 18
Care and Maintenance ...................................................................................... 19
CD Care Tips ................................................................................................ 20
The FCC Wants You to Know ....................................................................... 20
Specifications .................................................................................................... 21
7
42-5071.fm Page 8 Thursday, August 12, 1999 10:45 AM
PREPARATION
CONNECTING THE CD
CHANGER
Follow these steps to connect the CD
changer to your audio system and to
power.
Caution: Do not use the receiver/
amplifier’s PHONO inputs. Doing
so could damage the receiver/amplifier.
4. Plug the CD changer’s power cord
into a standard AC outlet.
CD Changer
USING THE REMOTE
CONTROL
Installing Batteries
Receiver/Amplifier
1. Select a location for your CD
changer that is near your receiver/
amplifier and a standard AC outlet.
Caution: Do not place the CD
changer on top of the receiver/amplifier or any other component that
gets hot.
Note: If you place the CD changer
near other audio components or
their wires, you might hear a hum
when you play a CD. To eliminate
the hum, move the components or
their wires.
2. Plug one end of the supplied audio cable into the CD changer’s
LINE OUT L (left) and R (right) output jacks, matching the red plug to
the red R jack and the white plug
to the white L jack.
3. Plug the other end of the cable
into the receiver/amplifier’s left
and right CD, AUX, or TAPE input
jacks.
8
Your CD changer’s remote control requires two AA batteries (not supplied)
for power. We recommend alkaline
batteries, such as RadioShack Cat.
No. 23-552, for the best performance
and longest life.
Cautions:
• Always use fresh batteries of the
required size and recommended
type.
• Do not mix old and new batteries,
different types of batteries (standard, alkaline, or rechargeable),
or rechargeable batteries of different capacities.
1. Press down on the battery compartment cover and slide it off.
illustration
42-5071.fm Page 9 Thursday, August 12, 1999 10:45 AM
2. Install the batteries in the compartment as indicated by the polarity symbols (+ and –) marked
inside.
illustration
Using the Remote
You can use the remote control for
any of the CD changer’s functions except turning power on/off and opening/
closing the CD compartment.
For the best results, point the remote
control toward REMOTE SENSOR on
the front of the CD changer.
3. Replace the cover.
You can use the remote control up to
a distance of about 20 feet. If the remote control operates erratically or
does not work, replace both batteries.
30
30 ×
×
30
30
feet
2020 Feet
Cautions:
• Never leave dead or weak batteries in the remote control. Batteries
can leak chemicals that can corrode the control.
• If you will not be using the remote
control for a month or more, remove the batteries.
9
42-5071.fm Page 10 Thursday, August 12, 1999 10:45 AM
OPERATION
LOADING CDS
Your CD changer can play 5-inch or 3inch CDs. Follow these steps to load
CDs.
4. Carefully place the CD, label side
up, into the recessed holder with
the label side up.
1. Press POWER on the CD changer.
The display lights.
illustration
illustration
Notes:
2. Press OPEN/CLOSE
disc tray.
to open the
illustration
• If you use a 3-inch CD, place it
in the middle of a recessed
holder.
• Do not load more than one CD
into each recessed disc holder.
• Each disc holder is marked with
a tray number (1–5).
5. Repeat Steps 3 and 4 to load
more CDs.
Caution: Do not force the compartment open or closed. You
might damage its loading mechanism.
3. Press DISC SKIP until the desired
disc tray moves to the front. (Do
not touch the disc tray while it rotates.)
illustration
10
6. Press OPEN/CLOSE to close the
disc tray. The CD changer displays the number of the CD in the
play position.
PLAYING CDS
After you load CDs, follow these steps
to play them.
Warning: The CD-8150 has a wide
dynamic range. If you set your amplifier’s volume too high during soft (low
volume) parts of the music, you might
damage your headphones, speakers,
or hearing when a sudden loud passage occurs.
42-5071.fm Page 11 Thursday, August 12, 1999 10:45 AM
1. Turn on your receiver/amplifier
and select the audio input to
which you connected your CD
changer (for example, CD, AUX,
or TAPE).
2. Press PLAY
to play the CD in
the play position from Track 1.
PLAY appears.
To select a different CD, see “Selecting a CD” on Page 12.
Note: During playback, if the
changer is subjected to a sudden
shock or jolt, the rotation speed
might change, or some noise
might be produced. This is not a
malfunction.
4. To temporarily stop playing, press
y PAUSE appears.
PAUSE y .
Press PAUSE y again or PLAY
to resume play.
To select a different track see “Selecting a Track” on Page 12.
3. While a CD plays, the CD changer
displays the current disc and track
number, the elapsed time of the
current track, and a music calendar that shows the total number of
tracks on the CD (up to 20) with
the current track number flashing.
illustration
Or, press STOP to stop play before the last CD ends.
illustration
illustration
When the CD changer finishes
playing a track, that track’s number disappears from the music
calendar.
Repeatedly press TIME on the remote control to display in order:
• The current track’s remaining
time
• The total number of tracks on
the CD and total playing time
5. After the CD changer plays all
tracks on the current CD, it automatically loads the next highernumbered CD and plays all of its
tracks. After it plays all tracks on
the highest-numbered CD, the CD
changer stops.
• The remaining number of tracks
and total time remaining on the
CD
• To return to the original display
11
42-5071.fm Page 12 Thursday, August 12, 1999 10:45 AM
SELECTING A CD
SELECTING A TRACK
To select a CD, press that DISC NO.
(1–5) button on the remote control,
then press PLAY
. The selected CD
plays from Track 1.
illustration
illustration
You can select a track in two ways.
You can enter the track number using
the remote control’s TRACK NO. buttons. Then press PLAY
.
To select the CD in the next highernumbered disc holder, press DISC
SKIP . The CD changer moves to the
next higher-numbered disc holder and
begins to play that CD.
Note: You cannot use DISC SKIP or
DISC NO. during programmed play
(see “Playing a Sequence of Tracks”
on Page 16).
Notes:
• If you enter a track number higher
than the highest track number on
a CD, the CD changer starts to
play the last track on that CD.
• You cannot use TRACK NO. during
programmed play (see “Playing a
Sequence of Tracks” on Page 16).
You can also select a particular track
with the
and
buttons.
While a CD is playing, press
once
to return to the beginning of the current track. Press
to skip other
tracks on the same CD.
12
42-5071.fm Page 13 Thursday, August 12, 1999 10:45 AM
Or, while the CD is stopped or
paused, press
or
until the
desired track number appears.
To quickly locate a track during programmed play, hold down
or
until you reach the desired track.
Note: If you try to advance past the
CD’s last track, the changer starts
counting again from Track 1. If you try
to move to before Track 1, the changer starts counting back from the last
track.
CHANGING CDS DURING
PLAYBACK
To open the disc tray without stopping
playback, press OPEN/CLOSE
on
the CD changer. The tray opens and
the current CD continues to play. You
can then change the CDs in the two
front holders.
Note: If you press DISC SKIP to rotate
the tray while the disc tray is open, the
CD changer stops playing the current
CD and starts playing the next loaded
CD.
13
42-5071.fm Page 14 Thursday, August 12, 1999 10:45 AM
SPECIAL FEATURES
AUDIBLE SEARCH
REPEAT PLAY
Use this feature during play to rapidly
search forward or backward for a specific section of a track on a CD. During
audible search, the CD plays at a lower volume and a higher speed.
Using the remote control, your CD
changer can repeat a single track, all
loaded CDs, or a programmed sequence.
To search forward or backward, hold
down SEARCH
or
on the remote control. Release the button to resume normal play.
illustration
illustration
Repeatedly press REPEAT on the remote control. The changer cycles
through these options:
REPEAT ONE — continuously replays the track
Note: You cannot search beyond the
beginning or end of a CD.
REPEAT ALL — replays all tracks on
all loaded CDs or the current programmed sequence
REPEAT disappears — cancels repeat play
To end repeat play, press REPEAT until REPEAT disappears, or press STOP
.
14
42-5071.fm Page 15 Thursday, August 12, 1999 10:45 AM
SHUFFLE PLAY
INTRO SCAN
To set the CD changer to select and
play all tracks in random order from
the loaded CDs or from a programmed sequence, before or during
play, press SHUFFLE. SHUFFLE appears.
Intro scan automatically plays the first
10 seconds of each track on the current CD through the CD loaded in disc
holder 5 or the programmed sequence. Press INTRO SCAN then
PLAY
PLAY ap. INTRO and
pear.
illustration
illustration
To cancel shuffle play at any time,
press SHUFFLE until SHUFFLE disappears, or press STOP .
To cancel intro scan and resume normal play, press INTRO SCAN.
To temporarily change the duration of
intro scan, when play is stopped, use
the TRACK NO. buttons on the remote
control to enter the desired play time
in seconds (1 to 99). Then press
INTRO SCAN followed by PLAY
to
start intro scan with the new duration.
Note: The intro scan duration returns
to 10 seconds all tracks have played.
15
42-5071.fm Page 16 Thursday, August 12, 1999 10:45 AM
PLAYING A SEQUENCE
OF TRACKS
You can program up to 32 selections
to play in any order you choose. A “selection” can be an individual track or
an entire CD.
Follow these steps to program and
play a sequence of tracks.
Hint: You can open the disc tray compartment while you program the sequence, so you can check the loaded
CDs’ tracks.
1. Press STOP
rent function.
to cancel the cur-
2. Press DISC NO. (or DISC SKIP) to
select a CD.
To enter all the tracks on a CD as
one selection, skip to Step 4.
3. Press TRACK NO. (or
to select a track.
or
)
4. Press MEMORY to store the selection into memory. The MEMORY
indicator appears and the time
P-01 (prodisplay
shows
grammed selection 1).
illustration
Note: If you enter a track number
higher than the highest track on a
CD, this entry is ignored during
programmed play.
5. Repeat Steps 2–4 for each track
or CD you want to program, up to
16
32 selections. The programmed
selection number on the display
increases with each added selection (P-02 to P-32).
Note: If you try to store more than
32 selections, the CD changer
briefly displays FULL.
to play the se6. Press PLAY
quence. If you programmed individual tracks, the music calendar
displays the number of programmed tracks, with the current
track number flashing. If you programmed an entire CD, the music
calendar displays only the current
track playing.
After the CD changer plays all
programmed tracks, it stops and
P-01 reappears on the time display. The sequence is still in memory, so you can press PLAY
to
replay the sequence.
Notes:
• You can use
or
, SEARCH
or
, INTRO SCAN, and
SHUFFLE during programmed
play.
• You cannot use the DISC SKIP,
DISC NO., or TRACK NO. buttons
during programmed play.
42-5071.fm Page 17 Thursday, August 12, 1999 10:45 AM
Checking/Changing the
Programmed Sequence
Adding to the Programmed
Sequence
Press STOP
to cancel the current
function. Press MEMORY CHECK . The
CD changer displays the programmed
sequence’s first selection. Each time
you press MEMORY CHECK, the CD
changer displays the next programmed selection.
You can add individual tracks or entire
CDs to the end of a programmed sequence up to a total of 32 tracks.
1. Repeatedly press STOP
until
0:00 appears. This cancels the
current function.
2. Enter the desired disc number
and/or track number, then press
MEMORY. The CD changer adds
the selection to the end of the programmed sequence.
illustration
To change a selection, repeatedly
press MEMORY CHECK until the CD
changer displays the disc number and
track number you want to change. Enter the desired disc number and/or
track number, then press MEMORY.
Erasing a Programmed
Sequence
To erase the programmed sequence
from memory, press STOP
then
CLEAR. The MEMORY indicator turns
off. The sequence is also erased
when you turn off the CD changer.
illustration
17
42-5071.fm Page 18 Thursday, August 12, 1999 10:45 AM
TROUBLESHOOTING
With proper care and handling, your CD changer should give you years of troublefree service. However, if your CD-8150 is not working properly, follow these suggestions to see if you can eliminate the problem. If you still have a problem, take
the CD changer to your local RadioShack store for assistance.
Problem
Suggestion
Power is on but no indicators
light.
Make sure the power cord is plugged into an
AC outlet.
CD is loaded but play does not
start.
The CD is loaded upside-down. Load the CD
with the label side up.
The CD is dirty or scratched. To clean the CD
surface, use a CD cleaner kit (such as Cat. No.
42-225). If the CD gets scratched, use Scratch
’n Fix (RadioShack Cat. No. 42-127).
The CD is not a standard (3- or 5-inch) compact disc. Load a standard size CD.
No sound.
The audio cable is not connected or is defective. Check all connections and replace defective cables, if necessary.
The sound is interrupted or the
same part repeats.
The CD is scratched or dirty. If the CD gets
scratched, use Scratch ’n Fix (RadioShack
Cat. No. 42-127). To clean the CD surface, use
a CD cleaner kit (such as Cat. No. 42-225).
Sound is distorted.
Moisture might be present on the pickup lens.
Unplug the CD changer from power and wait 2
hours for condensation to evaporate before
resuming play.
18
42-5071.fm Page 19 Thursday, August 12, 1999 10:45 AM
CARE AND MAINTENANCE
Your Optimus CD-8150 5-Disc Compact Disc Changer is an example of superior
design and craftsmanship. The following suggestions will help you care for the CD
changer so you can enjoy it for years.
Keep the CD changer dry. If it gets wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits.
Use and store the CD changer only in normal temperature environments. Temperature extremes can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.
Handle the CD changer gently and carefully. Dropping it can damage
circuit boards and cases and can cause the CD changer to work improperly.
Keep the CD changer away from dust and dirt, which can cause premature wear of parts.
Wipe the CD changer with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the CD changer.
Modifying or tampering with the your CD changer’s internal components can cause
a malfunction and might invalidate its warranty and void your FCC authorization to
operate it. If your CD changer is not performing as it should, take it to your local RadioShack store for assistance.
19
42-5071.fm Page 20 Thursday, August 12, 1999 10:45 AM
CD CARE TIPS
Even though a compact disc is very
durable, treat the CD surface with
care. Here are some tips:
• Do not place anything but a CD in
the disc tray. This can damage the
drive mechanism.
• Do not write on either side of the
CD, particularly the non-label side
(signals are read from the non-label side).
THE FCC WANTS YOU
TO KNOW
This system complies with the limits
for a Class B digital device as specified in Part 15 of FCC Rules. These
limits provide reasonable protection
against TV or radio interference in a
residential area. However, your system might cause TV or radio interference even when it is operating
properly.
• Do not store CDs in hightemperature, high-humidity locations. The CDs might warp.
To eliminate interference, you can try
one or more of the following corrective
measures.
• Keep CDs dry. A water drop can
act as a lens and affect the laser
beam’s focus.
• Reorient or relocate the TV or radio’s receiving antenna.
• Always handle a CD by the edges
to avoid fingerprints and always
keep it in its protective case or
sleeve when not in use. Fingerprints and scratches on the CD’s
surface can prevent the laser
beam from correctly reading the
digital information. To clean the
CD surface, use a CD cleaner kit
(such as Cat. No. 42-225). If the
CD gets scratched, use Scratch ’n
Fix (RadioShack Cat. No. 42127).
20
• Increase the distance between the
system and the TV or radio.
• Use outlets on different electrical
circuits for the system and the TV
or radio.
Consult your local RadioShack store if
the problem still exists.
42-5071.fm Page 21 Thursday, August 12, 1999 10:45 AM
SPECIFICATIONS
AUDIO
Frequency Response ................................................ 20 Hz–18 KHz, (1 kHz, 0 dB)
Channel Separation ................................................. More than 85 dB (1 kHz, 0 dB)
Harmonic Distortion ................................................ Less than 0.02% (1 kHz, 0 dB)
Dynamic Range .................................................................... 84 dB (1 kHz, –60 dB)
S/N Ratio ................................................................. More than 96 dB (1 kHz, 0 dB)
Wow and Flutter ............................................................................ Quartz Precision
SIGNAL FORMAT
Pickup ............................................................ Three-Beam Tracking Servo System
Object Lens Drive System ..................................... Two-Dimensional Parallel Drive
Sampling Frequency .................................................................................. 44.1 kHz
D/A Conversion ............................................................................. Dual 1-bit Linear
Filter ..................................................................................... 4 Times Oversampling
GENERAL
Power Supply ....................................................................................... 120V, 60 Hz
Power Consumption .................................................................................. 12 Watts
Dimensions (HWD) .......................................................... 41/2 × 171/8 × 143/4 Inches
(115 × 435 × 375 mm)
Weight .................................................................................................. 11 lbs 14 oz
(5.4 kg)
Specifications are typical; individual units might vary. Specifications are subject to
change and improvement without notice.
21
42-5071.fm Page 22 Thursday, August 12, 1999 10:45 AM
NOTES
22
42-5071.fm Page 23 Thursday, August 12, 1999 10:45 AM
23
42-5071.fm Page 24 Thursday, August 12, 1999 10:45 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
8A7
CEC6P10001920
Printed in China