Y610A, Y611A, and Y612A Series
Instruction Manual
Form 1477
January 2010
Y610A, Y611A, and Y612A Series Vacuum
Service Equipment and Relief Valves
!
Warning
Failure to follow these instructions or
to properly install and maintain this
equipment could result in an explosion,
fire and/or chemical contamination
causing property damage and personal
injury or death.
Fisher® vacuum breakers or relief
valves must be installed, operated
and maintained in accordance with
federal, state, and local codes, rules
and regulations, and Emerson Process
Management Regulator Technologies,
Inc. instructions.
If a leak develops or if the outlet
continually vents gas, service to the
unit may be required. Failure to correct
trouble could result in a hazardous
condition. Only a qualified person must
install or service the unit.
Introduction
Scope of the Manual
This manual describes and provides instructions and
parts lists for Y610A, Y611A, and Y612A Series
vacuum service equipment and relief valves.
Instructions and parts lists for other equipment used
with these regulators are found in separate manuals.
W1094_1
Figure 1. Type Y610A Vacuum Breaker
are used as vacuum breakers, the Y611A Series
devices are used as either vacuum breakers or relief
valves, and the Y612A Series devices are used as
vacuum regulators, and are described as follows:
Type Y610A—Direct-operated vacuum breaker
with upward pointing 1 NPT vent connection, and
internal registration requiring no downstream
control line.
The Y610A, Y611A, and Y612A Series devices are
used in a wide variety of vacuum and relief service
applications. The Y610A Series devices (Figure 1)
Type Y611A—Direct-operated relief valve with
upward pointing 1 NPT vent connection, and internal
registration requiring no downstream control line.
D103116X012
Product Description
Type Y610AP—Same as Type Y610A except with
blocked throat, diaphragm case assembly tapped
1/2 NPT for control line connection, and O-ring
stem seal.
www.fisherregulators.com
Y610A, Y611A, and Y612A Series
Specifications
Body Sizes (Inlet x Outlet) and End
Connection Style(2)
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP: 1-1/2 or 2 NPT,
or NPS 2 (DN 50) CL125 FF or
CL250 RF flanged
Temperature Capabilities(1)
-20° to 150°F (-29° to 66°C)
Pressure Information(1)
Type Y610A or Y610AP Vacuum Breaker:
See Table 1
Type Y611A or Y611AP Relief Valve: See Table 2
Type Y612A or Y612AP Vacuum Regulator:
See Table 3
Approximate Weights
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
With 1-1/2 NPT Body:
25 pounds (11 kg)
With NPS 2 (DN 50) Body:
30 pounds (14 kg)
Pressure Registration
Type Y610A, Y611A, or Y612A: Internal
Type Y610AP, Y611AP, or Y612AP: External
1. The pressure/temperature limits in this Instruction Manual and any applicable standard limitation should not be exceeded.
2. DIN (or other) end connections threaded to various national or international thread standards can usually be supplied; consult your local Sales Office.
Type Y611AP—Direct-operated vacuum breaker with
blocked throat, 1 NPT screened side vent, diaphragm
case assembly tapped 1/2 NPT for control line
connection, and O-ring stem seal.
Type Y612A—Direct-operated vacuum regulator with
upward pointing 1 NPT vent connection, and internal
registration requiring no downstream control line.
Type Y612AP—Same as Type Y612A except with
blocked throat, diaphragm case assembly tapped
1/2 NPT for control line connection, and O-ring
stem seal.
11A5497_J
Specifications
Figure 2. Nameplate
The Specifications section gives some general
Y610A, Y611A, and Y612A Series ratings and other
specifications. Individual regulator data as it comes
from the factory is stamped either on the closing cap
or on a nameplate (Figure 2).
Installation
!
Warning
Personal injury, property damage,
equipment damage, or leakage due to
escaping gas or bursting of pressurecontaining parts may result if this
2
equipment is overpressured or is
installed where service conditions could
exceed the limits given in Tables 1
through 3, or where conditions exceed
any ratings of the adjacent piping or
piping connections. To avoid such
injury or damage, provide pressurerelieving or pressure-limiting devices
(as required by the appropriate code,
regulation, or standard) to prevent
service conditions from exceeding
those limits.
Y610A, Y611A, and Y612A Series
Table 1. Types Y610A and Y610AP Vacuum Breaker Pressure Information
TYPES
Y610A,
Y610AP
Maximum
allowable
inlet (body)
pressure
Maximum
emergency
outlet
(casing)
pressure
(positive)
Psig
Psig
13
bar
0,90
bar
15
1,0
Outlet pressure
range (vacuum)
maximum
allowable
vacuum
With Spring Case
Above Diaphragm
With Spring Case
Below Diaphragm
Psig
bar
1 to 3-inches w.c.
(2 to 7 mbar)
0 to 2-inches w.c.
(0 to 5 mbar)
5.1
0,35
1.5 to 5-inches w.c.
(4 to 12 mbar)
0.50 to 4-inches w.c.
(1 to 10 mbar)
5.2
3 to 8-inches w.c.
(7 to 20 mbar)
2 to 7-inches w.c.
(5 to 17 mbar)
8 to 16-inches w.c.
(20 to 40 mbar)
control
spring
color code,
PART number
change
in outlet
(controlled)
pressure
required to
fully open
vacuum breaker
Psig
mbar
Brown Stripe,
1D892527022
0.043
3
0,36
Pink Stripe,
1D765427012
0.078
5
5.3
0,37
Purple Stripe,
0B019727052
0.143
1
7 to 15-inches w.c.
(17 to 37 mbar)
5.6
0,39
Gray,
1B766627062
0.181
12
16 to 32-inches w.c.
(40 to 80 mbar)
15 to 31-inches w.c.
(37 to 77 mbar)
6.1
0,42
Unpainted,
1B883327022
0.378
26
0.25 to 3 psig
(17 to 207 mbar)
0.25 to 3 psig
(17 to 207 mbar)
8.0
0,55
Black,
1A630627022
1.944
134
Table 2. Types Y611A and Y611AP Relief Valve Pressure Information
TYPES
Maximum
allowable
inlet (CASING)
pressure(1)
Psig
Y611A,
Y611AP
15
bar
1,0
Maximum
operating
inlet (relief)
pressure to
prevent part
damage(1)
INlet relief
set pressure range
Psig
bar
With Spring Case
Above Diaphragm
With Spring Case
Below Diaphragm
5.1
0,35
3 to 4-inches w.c.
(7 to 10 mbar)
2 to 3-inches w.c.
(5 to 7 mbar)
5.2
0,36
3.75 to 6-inches w.c
(9 to 15 mbar)
5.3
0,37
5.5
control
spring
color code,
part number
buildup over inlet
pressure required
to fully open
relief valve
Psig
mbar
Red,
1D892627022
0.089
6
2.75 to 5-inches w.c.
(6,9 to 12 mbar)
Red,
1D892727012
0.100
7
5 to 8-inches w.c.
(12 to 20 mbar)
4 to 7-inches w.c
(10 to 17 mbar)
Black,
1D892727012
0.124
9
0,38
7 to 16-inches w.c.
(17 to 40 mbar)
6 to 15-inches w.c.
(15 to 37 mbar)
White Stripe,
1D893227032
0.216
15
6
0,41
10 to 30-inches w.c
(25 to 75 mbar)
9 to 29-inches w.c.
(22 to 72 mbar)
Green,
1D893327032
0.351
24
6.5
0,45
0.75 to 1.5 psig
(52 to 103 mbar)
0.75 to 1.5 psig
(52 to 103 mbar)
Blue,
1H975827032
0.648
45
7.5
0,52
1 to 2.5 psig
(69 to 172 mbar)
1 to 2.5 psig
(69 to 172 mbar)
Orange,
1H975927032
1.026
71
1. Including buildup.
Additionally, physical damage to this
equipment could cause personal injury
or property damage due to escaping
gas. To avoid such injury or damage,
install the equipment in a safe and well
ventilated location.
Equipment operation within ratings does not
preclude the possibility of damage from debris in
the lines or from external sources. This equipment
should be inspected for damage periodically and
after any overpressure condition.
3
Y610A, Y611A, and Y612A Series
Table 3. Types Y612A and Y612AP Vacuum Regulator Pressure Information
Maximum
Maximum
operating
allowable
inlet
inlet
pressure
(casing)
to prevent
pressure
part
damage
Psig
15
bar
outlet pressure
range (vacuum)
Psig
bar
With Spring Case
Above Diaphragm
With Spring Case
Below Diaphragm
Psig
bar
5.1
0,35
1 to 3-inches w.c.
(2,5 to 7 mbar)
0 to 2-inches w.c.
(0 to 5 mbar)
5.1
0,35
5.2
0,36
5.2
5.3
0,37
3 to 8-inches w.c.
(7 to 20 mbar)
2 to 7-inches w.c.
(5 to 17 mbar)
5.6
0,39
8 to 16-inches w.c.
(20 to 40 mbar)
6.1
0,42
8.0
0,55
1,03
5/8-inch
(16 mm)
Port Diameter
1-inch
1-3/16-inch
(25 mm)
(30 mm)
Port Diameter Port Diameter
mbar
Psig
mbar
Psig
mbar
Brown Stripe,
1D892527022
0.089
6,1
0.053
3,6
0.076
5,2
0,36
Pink Stripe,
1D765427012
0.124
8,6
0.074
5,1
0.106
7,3
5.3
0,37
Purple Stripe,
0B019727052
0.189
13
0.112
7,7
0.161
11
7 to 15-inches w.c.
(17 to 37 mbar)
5.6
0,39
Gray,
1B766627062
0.227
16
0.134
9,3
0.193
13
16 to 32-inches w.c. 15 to 31-inches w.c.
(40 to 80 mbar)
(37 to 77 mbar)
6.1
0,42
Unpainted,
1B883327022
0.405
28
0.240
17
0.345
24
8.0
0,55
Black,
1A630627022
1.944
134
1.152
79
1.656
114
1.5 to 5-inches w.c. 0.50 to 4-inches w.c.
(4 to 12 mbar)
(1,2 to 10 mbar)
0.25 to 3 psig
(17 to 207 mbar)
0.25 to 3 psig
(17 to 207 mbar)
If this equipment is shipped mounted on
another unit, install that unit according
to the appropriate instruction manual.
1. Only personnel qualified through training and
experience should install, operate, and maintain
this equipment. For Y610A, Y611A, or
Y612A Series equipment that is shipped
separately, make sure that there is no damage to
or foreign material in it. Also ensure that all tubing
and piping have been blown free.
2. This equipment may be installed in any position
as long as the flow through the body is in the
direction indicated by the arrow cast on the
body. If continuous operation is required during
inspection or maintenance, install a three-valve
bypass around the equipment.
!
control
spring
color
code,
Part
Number
Psig
Note
Warning
This equipment may vent some gas
to the atmosphere. In hazardous or
flammable gas service, vented gas
may accumulate and cause personal
injury, death, or property damage due
to fire or explosion. Vent equipment in
hazardous gas service to a remote, safe
location away from air intakes or any
hazardous area. The vent line or stack
opening must be protected against
condensation or clogging.
4
maximum
allowable
vacuum
change in outlet (controlled)
PRESSURE REQUIRED TO FULLY OPEN
VACUUM REGULATOR
3. A Type Y610A or Y610AP vacuum breaker
(Figure 3) is used in applications where an
increase in vacuum must be limited. An
increase in vacuum (decrease in absolute
pressure) is transmitted to the lower side of the
diaphragm, opening the disk assembly. This
permits atmosphere, or an upstream vacuum
that has higher absolute pressure than the
downstream vacuum, to enter the system and
restore the controlled vacuum to its original
pressure setting. A Type Y610A direct-operated
vacuum breaker is self-contained and requires
no control line. A Type Y610AP vacuum breaker
requires a control line from the 1/2 NPT tapping
in the diaphragm case assembly (key 20,
Figure 4) to a point downstream of the body
(key 28, Figure 4).
4. A Type Y611AP vacuum breaker (Figure 3) also
is used in applications where an increase in
vacuum must be limited. An increase in vacuum
(decrease in absolute pressure) is transmitted
to the upper side of the diaphragm, opening
the disk assembly. This permits atmosphere,
or an upstream vacuum that has higher absolute
pressure than the downstream vacuum, to enter
the system and restore the controlled vacuum to
its original pressure setting. A Type Y611AP
vacuum breaker requires a control line from the
1/2 NPT tapping in the spring case assembly
(key 23, Figure 5) to a point downstream of the
body (key 28, Figure 5).
Y610A, Y611A, and Y612A Series
5. A Type Y611A relief valve (Figure 3) is used to
maintain a constant inlet pressure with the
outlet flowing to atmosphere or to any system
whose pressure is lower than the pressure at the
relief valve inlet. An increase in inlet pressure
opens the disk assembly, relieving the excess
pressure and restoring the inlet pressure to its
original setting. A Type Y611A direct-operated
relief valve is self-contained and requires no
control line.
6. A Type Y612A or Y612AP vacuum regulator is used
to maintain a constant vacuum at the regulator
inlet. A decrease in this vacuum (increase
in absolute pressure) beyond this value registers
underneath the diaphragm and opens the disk.
This permits a downstream vacuum of lower
absolute pressure than the upstream vacuum to
restore the upstream vacuum to its original pressure
setting. A Type Y612A (Figure 6) direct-operated
vacuum regulator is self-contained and requires no
control line. A Type Y612AP vacuum regulator
requires a control line from the 1/2 NPT tapping in
the diaphragm case assembly to a point upstream
of the body.
Startup and Adjustment
All Y610A, Y611A, or Y612A Series equipment can
be placed in operation by slowly introducing inlet
vacuum or pressure. This equipment takes control
when downstream vacuum or pressure is established.
This equipment is suitable for the pressure range
stamped on the nameplate (key 48, Figure 4, 5, or 6),
and listed in Tables 1 through 3. To adjust the pressure
setting, remove the closing cap (key 3, Figure 4, 5,
or 6), the adjusting screw clockwise to increase the
pressure setting or counterclockwise to decrease the
setting. Replace the cap after making this adjustment.
If desired, the closing cap may be wired to the hole
provided in the spring case to discourage tampering.
Shutdown
First close the nearest upstream shut-off valve and
then close the nearest downstream shut-off valve to
vent the equipment properly. Next, open the vent
valve between the equipment and the downstream
shut-off valve nearest to it. All pressure between
these shut-off valves is released through the open
vent valve.
Maintenance
Equipment parts are subject to normal wear and
must be inspected and replaced as necessary. The
frequency of inspection and replacement of parts
depends on the severity of service conditions and
upon applicable codes and government regulations.
!
Warning
To avoid personal injury, property
damage, or equipment damage caused
by sudden release of pressure or
explosion of accumulated gas, do not
attempt any maintenance or disassembly
without first isolating the regulator from
system pressure and relieving all internal
pressure from the equipment.
Body Area
These procedures are for gaining access to the disk
assembly, seat ring, and body gasket or diaphragm
case O-ring. All pressure must be released from
the diaphragm case before the following steps can
be performed.
Type Y610A or Y610AP Vacuum Breaker
Key numbers are referenced in Figure 4.
1. To inspect or replace the seat O-ring (key 39) or
seat ring (key 27), loosen the diaphragm case
cap screws (key 29), remove the union ring
(key 20D), and separate the diaphragm case
assembly (key 20) from the body (key 28).
2. Remove the diaphragm case O-ring (key 15) and
inspect the body (key 28).
3. Inspect and replace the seat ring (key 27) if
necessary. Lubricate the threads of the
replacement seat ring with a good grade of pipe
sealant and tighten using 29 to 37 foot-pounds
(39 to 50 N•m) of torque.
4. If it is necessary to replace the seat O-ring
(key 39), remove the disk assembly cap screw
(key 44), seal washer (key 45), seat O-ring washer
(key 32), and seat O-ring from the valve stem
(key 13).
5. Install the seat O-ring (key 39), seat O-ring
washer (key 32), and seal washer (key 45) onto
the seat O-ring holder (key 31), and secure with
the disk assembly cap screw (key 44).
5
Y610A, Y611A, and Y612A Series
vacuum
being
limited
atmosphere
only
Vacuum
pump
Y610A series
vacuum breaker
Y611A series
vacuum breaker
positive pressure or atmosphere,
or a lesser vacuum than the
vacuum being limited
vacuum
being
limited
AJ7856_A
A2991_2
Vacuum
pump
Y610A series vacuum breaker
AJ7853_A
A2992_2
Y611A series vacuum breaker
p1
Unavoidable
leakage
Inlet pressure
being controlled
oR protected
Vacuum
being
controlled
Y612A series
vacuum regulator
Higher vacuum source
Y611A series
relief valve
Vacuum pump
p2
AJ7854_A
A2993_2
Atmosphere or any pressure
less than p1
AJ7865_A
A2994_2
Y612A series vacuum regulator
Y611A series relief valve
Figure 3. Installation Schematics
6. If necessary, install a replacement diaphragm case
O-ring (key 15) into the body (key 28).
7.
6
Install the diaphragm case assembly (key 20)
on the body (key 28) and secure with the union
ring (key 20D) and diaphragm case cap screws
(key 29).
Type Y611A or Y611AP Vacuum Breaker
or Relief Valve or Type Y612A or Y612AP
Vacuum Regulator
Types Y611A and Y611AP key numbers are
referenced in Figure 5 and Types Y612A and Y612AP
key numbers are referenced in Figure 6.
Y610A, Y611A, and Y612A Series
1. To inspect and replace the disk assembly (key 25),
remove the body cap (key 38).
2. Unscrew the disk spacer (key 43) and remove the
disk assembly (key 25), disk assembly gasket
(key 26), and disk spring (key 41) from the valve
stem (key 40).
3. To inspect and replace the seat ring (key 27), loosen
the diaphragm case cap screws (key 29), remove
the union ring (key 20D), and separate the
diaphragm case assembly (key 20) from the body
(key 28).
4. Remove the diaphragm case O-ring (key 15) and
inspect the body (key 28).
5. Inspect and replace the seat ring (key 27) if
necessary. Lubricate the threads of the
replacement seat ring with a good grade of pipe
sealant and tighten using 29 to 37 foot-pounds
(39 to 50 N•m) of torque.
6. If necessary, install a replacement diaphragm case
O-ring (key 15) into the body (key 28).
7. Install the diaphragm case assembly (key 20) on the
body (key 28) and secure with the union ring
(key 20D) and diaphragm case cap screws
(key 29).
3. Remove the diaphragm (key 5) and attached
parts by tilting it so that the pusher post (key 8)
slips off the lever assembly (key 9). To separate
the diaphragm (key 5) from the attached parts,
unscrew the diaphragm nut (key 37). If the only
further maintenance is to replace the diaphragm
parts or change the control spring (key 1), skip to
step 8.
4. To replace the lever assembly (key 9), remove the
machine screws (key 11) and lever pin (key 10).
5. To replace the valve stem (key 13) or stem seal
O-ring (key 46) perform Type Y610A or Y610AP
body area maintenance procedure step 4 and pull
the valve stem out of the stem adaptor (key 60).
6. Grease the replacement stem seal O-ring (key 46)
with a good grade of elastomer lubricant and
install on the valve stem (key 13). Install the
valve stem by pushing it into the stem adaptor
(key 60) and perform Type Y610A or Y610AP
body area maintenance procedure steps 5 and 6
if necessary.
7. Install the lever assembly (key 9) into the valve stem
(key 13) and secure the lever assembly (key 9) with
the lever pin (key 10) and machine screws (key 11).
8. Install the disk spring (key 41), disk assembly
gasket (key 26), and disk assembly (key 25) on
the disk stem (key 40) and attach using the disk
spacer (key 43).
8. Install the small diaphragm plate gasket (key 7),
diaphragm plate (key 24), and diaphragm
(key 5) on the pusher post (key 8) and attach with
the diaphragm nut (key 37). Tighten using 30 to
45 foot-pounds (41 to 61 N•m) of torque.
9. Use a good quality thread sealer when replacing
the body cap (key 38) assembly.
9. Install the pusher post (key 8) plus attached
diaphragm parts onto the lever assembly (key 9).
Diaphragm and Spring Case Area
These procedures are for gaining access to the
control spring, diaphragm assembly, valve stem, and
stem O-ring. All pressure must be released from the
diaphragm case before these steps can be performed.
Type Y610A or Y610AP Vacuum Breaker
Key numbers are referenced in Figure 4.
1. Remove the closing cap (key 3) and turn the
adjusting nut (key 18) counterclockwise until all
compression is removed from the control spring
(key 1).
2.
Remove the spring case cap screws (key 21) and
hex nuts (key 22) and lift off the spring case
assembly (key 23). If the only further maintenance is
to change the control spring (key 1), skip to step 10.
10. Install the spring case assembly (key 23) and
control spring (key 1) on the diaphragm case
assembly (key 20) so that the vent assembly
(key 65, not shown) is correctly oriented, and
secure them with the spring case cap screws
(key 21) and hex nuts (key 22) to
finger tightness only.
11. Turn the adjusting nut (key 18) clockwise until
there is enough control spring (key 1) force to
provide proper slack to the diaphragm (key 5)
and attached parts. Using a crisscross pattern,
finish tightening the spring case cap screws
(key 21) and hex nuts (key 22) to 55 to
75 inch-pounds (6,2 to 8,5 N•m) of torque. Then
finish turning the adjusting nut (key 18) to the
desired outlet pressure setting.
12. Install a replacement closing cap gasket (key 35) if
necessary, and then install the closing cap (key 3).
7
Y610A, Y611A, and Y612A Series
Type Y611A or Y611AP Vacuum Breaker
or Relief Valve
Key numbers are referenced in Figure 5.
1. Remove the closing cap (key 3) and turn the
adjusting screw (key 2) counterclockwise until all
compression is removed from the control spring
(key 1).
2. Remove the spring case cap screws (key 21) and
hex nuts (key 22) and lift off the spring case
assembly (key 23). If the only further maintenance
is to change the control spring (key 1), skip to
step 10.
3. Remove the diaphragm (key 5) and attached
parts by tilting it so that the pusher post (key 8)
slips off the lever assembly (key 9). To separate
the diaphragm (key 5) from the attached parts,
unscrew the diaphragm plate cap screw
(key 64). If the only further maintenance is to
replace the diaphragm parts or change the control
spring (key 1), skip to step 8.
4. To replace the lever assembly (key 9), remove the
machine screws (key 11) and lever pin (key 10).
5. To replace the valve stem (key 13) or stem seal
O-ring (key 46) pull the valve stem out of the stem
adaptor (key 60).
6. Grease the replacement stem seal O-ring (key 46)
with a good grade of elastomer lubricant and
install on the valve stem (key 13). Install the valve
stem by pushing it into the stem adaptor (key 60).
7. Install the lever assembly (key 9) into the valve stem
(key 13) and secure the lever assembly (key 9) with
the lever pin (key 10) and machine screws (key 11).
8. Install the small diaphragm plate gasket (key 7),
diaphragm plate (key 24), and diaphragm (key 5)
on the pusher post (key 8) and attach with the
diaphragm plate cap screw (key 64). Tighten
using 30 to 45 foot-pounds (41 to 61 N•m)
of torque.
9. Install the pusher post (key 8) plus attached
diaphragm parts onto the lever assembly (key 9).
10. Install the spring case assembly (key 23)
and control spring (key 1) on the diaphragm
case assembly (key 20) so that the vent
assembly (key 65, not shown) is correctly
oriented, and secure them with the spring case
cap screws (key 21) and hex nuts (key 22) to
finger tightness only.
11. Turn the adjusting screw (key 2) clockwise until
there is enough control spring (key 1) force to
provide proper slack to the diaphragm (key 5)
8
and attached parts. Using a crisscross pattern,
finish tightening the spring case cap screws
(key 21) and hex nuts (key 22) to 55 to
75 inch-pounds (6,2 to 8,5 N•m) of torque. Then
finish turning the adjusting screw (key 2) to the
desired outlet pressure setting.
12. Install a replacement closing cap gasket (key 35) if
necessary, and then install the closing cap (key 3).
Type Y612A or Y612AP Vacuum Regulator
Key numbers are referenced in Figure 6.
1. Remove the closing cap (key 3) and turn the
adjusting nut (key 18) counterclockwise until all
compression is removed from the control spring
(key 1).
2. Remove the spring case cap screws (key 21) and
hex nuts (key 22) and lift off the spring case
assembly (key 23). If the only further maintenance
is to change the control spring (key 1), skip to
step 10.
3. Remove the diaphragm (key 5) and attached
parts by tilting it so that the pusher post (key 8)
slips off the lever assembly (key 9). To separate
the diaphragm (key 5) from the attached parts,
unscrew the diaphragm nut (key 37). If the only
further maintenance is to replace the diaphragm
parts or change the control spring (key 1), skip to
step 8.
4. To replace the lever assembly (key 9), remove the
machine screws (key 11) and lever pin (key 10).
5. To replace the valve stem (key 13) or stem seal
O-ring (key 46) pull the valve stem out of the stem
adaptor (key 60).
6. Grease the replacement stem seal O-ring (key 46)
with a good grade of elastomer lubricant and
install on the valve stem (key 13). Install the
valve stem by pushing it into the stem adaptor
(key 60).
7. Install the lever assembly (key 9) into the valve stem
(key 13) and secure the lever assembly (key 9) with
the lever pin (key 10) and machine screws (key 11).
8. Install the small diaphragm plate gasket (key 7),
diaphragm plate (key 24), and diaphragm
(key 5) on the pusher post (key 8) and attach with
the diaphragm nut (key 37). Tighten using 30 to
45 foot-pounds (41 to 61 N•m) of torque.
9. Install the pusher post (key 8) plus attached
diaphragm parts onto the lever assembly (key 9).
10. Install the spring case assembly (key 23) and
control spring (key 1) on the diaphragm case
Y610A, Y611A, and Y612A Series
assembly (key 20) so that the vent assembly
(key 65, not shown) is correctly oriented,
and secure them with the spring case cap
screws (key 21) and hex nuts (key 22) to
fingertightness only.
11. Turn the adjusting nut (key 18) clockwise until
there is enough control spring (key 1) force to
provide proper slack to the diaphragm (key 5)
and attached parts. Using a crisscross pattern,
finish tightening the spring case cap screws
(key 21) and hex nuts (key 22) to 55 to
75 inch-pounds (6,2 to 8,5 N•m) of torque. Then
finish turning the adjusting nut (key 18) to the
desired outlet pressure setting.
12. Install a replacement closing cap gasket (key 35)
if necessary, and then install the closing cap
(key 3).
Parts Ordering
When corresponding with the local Sales Office
about this regulator, include the type number and all
other pertinent information stamped on the closing
cap (key 3) or nameplate (key 48). Specify the
eleven-character part number when ordering new
parts from the following parts list.
Parts List (Figures 4 through 6)
Key Description
1
Control Spring,
Steel
2
Adjusting Screw
Type Y611A or Y611AP,
For aluminum
3
Closing Cap
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP, Aluminum
4
Control Spring Seat
Type Y610A, Y610AP, Y612A, or Y612AP,
Cast iron
5* Diaphragm, Aluminum
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
7* Small Diaphragm Plate Gasket
Type Y610A, Y610AP, Y611A, or Y611AP,
Aluminum
8
Pusher Post
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP, Aluminum
9
Lever Assembly, Plated steel
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP, Aluminum
10 Lever Pin
Stainless steel
Part Number
See following table
1L928608012
1L928308012
1U226019012
1K649602052
1L143403022
1L143311992
1H974028992
Key Description
Part Number
11 Machine Screw (2 required)
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP, Plated steel
1B420428982
12 Control Spring Seat
Steel
See following table
13 Stem Assembly
Type Y610A, Aluminum
1H9748000A2
Type Y610AP, Aluminum
1L1426000A2
Type Y611A, Y611AP, Y612A, or Y612AP,
Aluminum
1L2212000A2
15* Diaphragm Case O-ring, Nitrile (NBR)
1F358106992
18 Adjusting Nut (for Type Y610A, Y610AP,
Y612A, or Y612AP only), Brass
1A201914012
20 Diaphragm Case Assembly
Type Y610A, Y611A, or Y612A, Aluminum
1H9751X0012
Type Y610AP, Y611AP, or Y612AP, Aluminum
1H9751X0022
21 Spring Case Cap Screw, Plated steel
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP (12 required)
1B136324052
22 Hex Nut, Cadmium plated steel
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP (12 required)
1A309324122
23 Spring Case Assembly
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP, Aluminum
4L142308032
24 Diaphragm Plate
See following table
25* Disc Assembly
(not use with Type Y610A or Y610AP)
Type Y611A, Y611AP, Y612A, or Y612AP,
Aluminum disk holder and Nitrile (NBR) disk
1H9739000A2
26* Disc Assembly Gasket (for Type Y611A, Y611AP,
Y612A, or Y612AP only), Composition
1F826804022
27* Seat Ring
Type Y610A or Y610AP, Aluminum
3/4-inch (19 mm) port diameter
1H979509022
1-3/6-inch (30 mm) port diameter
1L220809022
Type Y611A or Y611AP, Aluminum
1-3/6-inch (30 mm) port diameter
1H980809022
Type Y612A or Y612AP, Aluminum
5/8-inch (16 mm) port diameter
1H980509022
1-inch (25 mm) port diameter
1H980709022
1-3/6-inch (30 mm) port diameter
1H980809022
28 Body
Type Y610A or Y610AP
Cast iron
1-1/2 NPT
1J190319012
2 NPT 1H974919012
NPS 2 (DN 50) CL125 FF flanged
2K184219012
Steel
1-1/2 NPT
1K787922012
2 NPT
1K791222012
Type Y611A, Y611AP, Y612A, or Y612AP
Cast iron
1-1/2 NPT
1J190519012
2 NPT
1H974319012
NPS 2 (DN 50) CL125A FF flanged
1K184319012
Steel
1-1/2 NPT
1K788022012
2 NPT 1K792222012
29 Diaphragm Case Cap Screw
(for Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP only),
Plated steel (2 required)
1H974724052
1H972935032
*Recommended Spare Parts
9
Y610A, Y611A, and Y612A Series
23
1
48
5
20
8
10
20D
46
58
54
35
55
50
51
52
22
53
24
56
SECTION A-A
7
18
9
12
13
4
60
11
15
21
57
3
66
A
A
37
59
47
29
28
44
27
45
51A1731_A
B2048
39
31
32
Figure 4. Type Y610AP Vacuum Breaker
section a-a
57
a
56
50
a
51
54
35
23D
64
4
5B
7
20A
51A1733_A
3
21
2
15
1
27
48
43
55
52
29
20D
13
AS
SP
5A
26
22
38
8
9
25
40
41
ls
part not shown: 20E
as - Anti-seize
ls - lead seal
sp - houghton staput no. 14
Figure 5. Type Y611A Relief Valve Assembly
10
53
11
28
10
Y610A, Y611A, and Y612A Series
Key 1 Control Spring, Steel
Key 12 Control Spring Seat, Steel
Key 24 Diaphragm Plate, Steel
Key 64 Diaphragm Plate Cap Screw, Plated steel
types
KEY 1(1)
KEY 12
KEY 24
KEY 64
Color Code
Part Number
Part Number
Part Number
Quantity Required
Part Number
Y610A, Y610AP
Brown Stripe
Pink Stripe
Purple Stripe
Gray
Unpainted
Black
1D892527022
1D765427012
0B019727052
1B766627062
1B883327022
1A630627022
1A869524092
1A869524092
1A869524092
1A869524092
1A626424092
1A626424092
0B006628982
0B006628982
0B006628982
0B006628982
0B006628982
1A347825022
2
2
2
2
2
2
-------------------
Y611A, Y611AP
Red
Red
Black Stripe
White Stripe
Green
Blue
Orange
1D892627022
1D892627022
1D892727012
1D893227032
1D893327032
1H975827032
1H975927032
----------------------
0B006628982
0B006628982
0B006628982
0B006628982
0B006628982
1A347825022
1A347825022
2
2
2
2
2
2
2
1C473224052
1C473224052
1C473224052
1C473224052
1C473224052
1A667824052
1A667824052
Y612A, Y612AP
Brown Stripe
Pink Stripe
Purple Stripe
Gray
Unpainted
Black
1D892527022
1D765427012
0B019727052
1B766627062
1B883327022
1A630627022
1A869524092
1A869524092
1A869524092
1A869524092
1A626424092
1A626424092
0B006628982
0B006628982
0B006628982
0B006628982
0B006628982
1A347825022
2
2
2
2
2
2
-------------------
1. See Tables 1 through 3 for spring ranges.
Key Description
31
Seat O-ring Holder
(for Type Y610A or Y610AP only), Aluminum
32 Seat O-ring Washer
(for Type Y610A or Y610AP only), Aluminum
35* Closing Cap Gasket, Neoprene (CR)
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
37 Diaphragm Nut (for Type Y610A, Y610AP,
Y612A, or Y612AP only), Aluminum
38 Body Cap Assembly
Type Y611A, Y611AP, Y612A, or Y612AP,
Aluminum
39* Seat O-ring (for Type Y610A or Y610AP only),
Nitrile (NBR)
40 Valve Stem
Type Y611A, Y611AP, Y612A, or Y612AP,
Aluminum
41 Back Disk Spring
Type Y611A, Y611AP, Y612A, or Y612AP
43 Disk Spacer
Type Y611A, Y611AP, Y612A, or Y612AP,
Aluminum
44 Cap Screw (for Type Y610A or Y610AP only),
Aluminum
45 Dyna-Seal Washer
(for Type Y610A or Y610AP only), Aluminum
46* Stem Seal O-ring (for Type Y610AP,
Y611AP, or Y612AP only), Nitrile (NBR)
50 Flapper Stem
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
51 Lower Flapper
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
Part Number 1L154909012
1V5121X0012
1N446206992
1A499724122
1R236109022
1F2595X0082
1H973509082
1L303837022
1H973609012
1E760324052
1F990428982
1E216306992
1H976335022
Key Description
Part Number
52 Upper Flapper
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
1H976506992
53 Flapper Seat (for Type Y610A, Y610AP,
Y611A, Y611AP, Y612A, or Y612AP only),
Stainless steel
T13609T0012
54 Self Tapping Screw (3 required)
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
1H976728982
55 Spring (2 required)
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
1H976837022
56 Screen
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
1E564843122
57 Snap Ring
Type Y610A, Y610AP, Y611A, Y611AP,
Y612A, or Y612AP
1E564937022
58 Retaining Ring
Type Y610AP, Y611AP, or Y612AP
1L142838992
59 O-Ring
Type Y610AP, Y611AP, or Y612AP
1L142906992
60 Stem Adaptor
Type Y610AP, Y611AP, or Y612AP
1L143109012
64 Diaphragm Plate Cap Screw,
Plated steel
See folowing table
65 Type Y602-1 Vent Assembly,
Spring Case Up
Type Y602-11
Spring Case Down
Type Y602-2
66 Stem
Type Y610A, Y610AP, Y612A, or Y612AP
1A626314012
1H976406992
*Recommended Spare Parts
11
Y610A, Y611A, and Y612A Series
1
23A
48
54
35
55
50
51
53
22
5B
20A
8
10
20D
52
5A
SECTION A-A
56
7
18
9
12
13
4
15
11
28
21
27
29
57
3
66
A
A
37
AS
LS
38
40
41
26
25
43
PART NOT SHOWN: 20E
AS - ANTI-SEAL
LS - LEAD SEAL
51A1737_A
Figure 6. Type Y612A Vacuum Regulator
Industrial Regulators
Natural Gas Technologies
TESCOM
Emerson Process Management
Regulator Technologies, Inc.
Emerson Process Management
Regulator Technologies, Inc.
Emerson Process Management
Tescom Corporation
USA - Headquarters
McKinney, Texas 75069-1872 USA
Tel: 1-800-558-5853
Outside U.S. 1-972-548-3574
USA - Headquarters
McKinney, Texas 75069-1872 USA
Tel: 1-800-558-5853
Outside U.S. 1-972-548-3574
USA - Headquarters
Elk River, Minnesota 55330-2445 USA
Tel: 1-763-241-3238
Asia-Pacific
Shanghai, China 201206
Tel: +86 21 2892 9000
Asia-Pacific
Singapore, Singapore 128461
Tel: +65 6777 8211
Europe
Bologna, Italy 40013
Tel: +39 051 4190611
Europe
Bologna, Italy 40013
Tel: +39 051 4190611
Gallardon, France 28320
Tel: +33 (0)2 37 33 47 00
Middle East and Africa
Dubai, United Arab Emirates
Tel: +971 4811 8100
Europe
Selmsdorf, Germany 23923
Tel: +49 (0) 38823 31 0
For further information visit www.fisherregulators.com
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls, Inc., a
business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson
Process Management product remains solely with the purchaser.
©Emerson Process Management Regulator Technologies, Inc., 1973, 2010; All Rights Reserved