DPH-70 Modem IP Phone
User’s Guide
Rev. 03 (Sep 2003)
DPH-70 Rev.03
Printed In Taiwan
RECYCLABLE
Warranty and Registration
Trademarks
Copyright  2003 D-Link Corporation.
Contents subject to change without prior notice.
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to
their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to make any derivative
such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link
Systems Inc., as stipulated by the United States Copyright Act of 1976.
Hardware:
D-Link warrants each of its hardware products to be free from defects in workmanship and materials under
normal use and service for a period commencing on the date of purchase from D-Link or its Authorized
Reseller and extending for the length of time stipulated by the Authorized Reseller or D-Link Branch Office
nearest to the place of purchase.
This Warranty applies on the condition that the product Registration Card is filled out and returned to a
D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back of this
manual, together with a copy of the Registration Card.
If the product proves defective within the applicable warranty period, D-Link will provide repair or
replacement of the product. D-Link shall have the sole discretion whether to repair or replace, and
replacement product may be new or reconditioned. Replacement product shall be of equivalent or better
specifications, relative to the defective product, but need not be identical. Any product or part repaired by
D-Link pursuant to this warranty shall have a warranty period of not less than 90 days, from date of such
repair, irrespective of any earlier expiration of original warranty period. When D-Link provides replacement,
then the defective product becomes the property of D-Link.
Warranty service may be obtained by contacting a D-Link office within the applicable warranty period, and
requesting a Return Material Authorization (RMA) number. If a Registration Card for the product in question
has not been returned to D-Link, then a proof of purchase (such as a copy of the dated purchase invoice)
must be provided. If Purchaser's circumstances require special handling of warranty correction, then at the
time of requesting RMA number, Purchaser may also propose special procedure as may be suitable to the
case.
After an RMA number is issued, the defective product must be packaged securely in the original or other
suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be
prominently marked on the outside of the package. The package must be mailed or otherwise shipped to
D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall never be responsible for any
software, firmware, information, or memory data of Purchaser contained in, stored on, or integrated with any
product returned to D-Link pursuant to this warranty.
Any package returned to D-Link without an RMA number will be rejected and shipped back to Purchaser at
Purchaser's expense, and D-Link reserves the right in such a case to levy a reasonable handling charge in
addition mailing or shipping costs.
Software:
Warranty service for software products may be obtained by contacting a D-Link office within the applicable
warranty period. A list of D-Link offices is provided at the back of this manual, together with a copy of the
Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office,
then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting
warranty service. The term "purchase" in this software warranty refers to the purchase transaction and
resulting license to use such software.
D-Link warrants that its software products will perform in substantial conformance with the applicable
product documentation provided by D-Link with such software product, for a period of ninety (90) days from
the date of purchase from D-Link or its Authorized Reseller. D-Link warrants the magnetic media, on which
D-Link provides its software product, against failure during the same warranty period. This warranty applies
to purchased software, and to replacement software provided by D-Link pursuant to this warranty, but shall
not apply to any update or replacement which may be provided for download via the Internet, or to any
update which may otherwise be provided free of charge.
D-Link's sole obligation under this software warranty shall be to replace any defective software product with
product which substantially conforms to D-Link's applicable product documentation. Purchaser assumes
responsibility for the selection of appropriate application and system/platform software and associated
reference materials. D-Link makes no warranty that its software products will work in combination with any
hardware, or any application or system/platform software product provided by any third party, excepting only
2
such products as are expressly represented, in D-Link's applicable product documentation as being
compatible. D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but
D-Link shall have no obligation to provide compatibility when there is fault in the third-party hardware or
software. D-Link makes no warranty that operation of its software products will be uninterrupted or
absolutely error-free, and no warranty that all defects in the software product, within or without the scope of
D-Link's applicable product documentation, will be corrected.
D-Link Offices for Registration and Warranty Service
The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To
obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a
software product, contact the D-Link office nearest you. An addresses/telephone/fax list of D-Link offices is
provided in the back of this manual.
LIMITATION OF WARRANTIES
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE
REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR
IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE
OF D-LINK'S PRODUCTS
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR
TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD.
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF
PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES
ARISING OUT THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR
INTERRUPTION OF A D-LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.
THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT ALLOW
THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
3
TABLE OF CONTENTS
1
OVERVIEW
5
1.1
ACRONYMS ...............................................................................................................................6
1.2
DEFINITIONS .............................................................................................................................7
2
UNPACKING AND INSTALLATION
8
2.1
SYSTEM REQUIREMENTS ..........................................................................................................8
2.2
INSTALLATION ...........................................................................................................................8
3
GETTING STARTED
9
4
MAKING AND RECEIVING INTERNET PHONE CALLS
11
4.1
TO MAKE AN INTERNET CALL ................................................................................................. 11
4.2
RECEIVING INTERNET CALLS .................................................................................................. 12
4.3
TRANSFERRING INTERNET CALLS ........................................................................................... 12
5
PSTN PHONE CALLS
12
5.1
MAKING PSTN CALL .............................................................................................................. 13
5.2
RECEIVING PSTN CALL ......................................................................................................... 13
5.3
TRANSFERRING PSTN CALL .................................................................................................. 13
6
DPH-70 CONFIGURATION
14
6.1
ISP PARAMETERS ................................................................................................................. 15
6.2
CALLING CARD PARAMETERS ................................................................................................ 16
6.3
REVIEW CONFIGURATION....................................................................................................... 16
6.4
SAVE AND EXIT ...................................................................................................................... 17
6.5
EXTENDED MENU .................................................................................................................. 17
7
ADDITIONAL FEATURES
20
7.1
UPGRADING SOFTWARE ........................................................................................................ 20
7.2
LOADING FACTORY DEFAULTS ................................................................................................ 20
APPENDIX A: ENTERING ALPHANUMERIC AND SPECIAL CHARACTERS
21
7.3
ENTERING DIGITS .................................................................................................................. 21
7.4
ENTERING SMALL (LOWER-CASE) LETTERS ........................................................................... 21
7.5
ENTERING CAPITAL (UPPER-CASE) LETTERS ......................................................................... 22
7.6
ENTERING SPECIAL CHARACTERS ......................................................................................... 22
8
APPENDIX B: TROUBLESHOOTING
23
9
APPENDIX C: DPH-70 PRODUCT SPECIFICATIONS
25
4
DPH-70 User’s Guide
1 Overview
The DPH-70 is a two-in-one phone, allowing both Internet (IP) based calls, and normal PSTN
(Public Switched Telephone Network) calls. As an IP telephone, the DPH-70 operates under the
Session Initiation Protocol (SIP) or the H.323 protocol, allowing you to make inexpensive long
distance (STD and ISD) calls on a dial-up Internet connection.
With the look, feel, and ease of use of any normal phone, the DPH-70 toggles between Internet
and PSTN modes with one-button convenience. Use the DIAL UP button to initiate IP calls; deactivate the DIAL UP function to revert to PSTN mode.
Once the DPH-70 has been configured, it works like any normal phone. There is no need to reconfigure unless there is a change in Internet access or calling card information.
The DPH-70 is a standards-based device and works with any Internet Service Provider (ISP) and
VoIP (Internet telephone) service provider. It plays user-friendly status messages and
configuration messages in a language of your choice.
DPH-70 has a user-friendly dialing option whereby you dial a number just once. The phone will try
many times and ring back when the called party answers the call.
DPH-70 software can be upgraded over the Internet for new features and functions.
5
DPH-70 User’s Guide
1.
Hook switch
2.
Label inset
3.
Dial-Up button
4.
Shift button
5.
Redial button
6.
Speaker LED indicator and
one-touch dialing
7.
LED Indicator for Dial-Up
and Shift
8.
Number keypad
Features
Two-in-one device supports Internet and PSTN phone calls.
Standards-based device, works with all Internet Service Provider (ISP), VoIP service
providers, and PC-based soft phones.
Simple to set up, guided by voice prompts in your chosen language.
The most suitable audio codec (G.723 or G.729A) will be automatically selected, based
on Internet connection speed.
Excellent voice quality and low end-to-end delay using low latency adaptive jitter buffer,
silence suppression, and comfort noise generation techniques.
User-friendly one-hand dialing method.
Call transfer and last number redial.
Continuous-connection option (DIAL UP) allows you to make multiple calls without
connecting to the Internet each time.
Adjustable speaker volume control.
Password protection for your valuable configuration information.
Remote software update support.
1.1
Acronyms
One of the realities of the modern world, particularly when it comes to computers and the Internet,
is the widespread use of acronyms – groups of letters that refer to a product or service or a widely
used standard (protocol). Here’s a short list of acronyms that should help you, at least with this
manual and the DPH-70.
LED
IP
ISP
PPP
PSTN
RTP
SIP
TFTP
Light Emitting Diode
Internet Protocol
Internet Service Provider
Point-to-Point Protocol
Public Switched Telephone Network
Real Time Protocol (RFC-1889)
Session Initiation Protocol
Trivial File Transfer Protocol
6
DPH-70 User’s Guide
VoIP
1.2
Voice Over Internet Protocol, same as Internet Telephony
Definitions
Idle State: DPH-70 is said to be in idle state when the speaker is off, LEDs are off and the
handset is on Hook.
Configuration State: DPH-70 goes to configuration state to edit and verify the configuration
information.
Receive State: DPH-70 goes to this state to receive calls from other phones. In this state, phone
is always connected to Internet.
Speaker Mode: Allows one-hand dialing and monitoring of call-progress messages.
Handset Mode: Lift the handset any time to listen. The speaker will be turned off automatically.
7
DPH-70 User’s Guide
2 Unpacking and Installation
Open the shipping carton and carefully remove all items. In addition to this User's Guide, make
sure you have received all of the following:
• Modem IP phone, DPH-70
• One telephone cable (RJ-11)
• Handset
• Handset cord
• Power adapter
• Warranty card
If any item is missing or damaged, please contact your local reseller.
2.1
System Requirements
You will need the following to use DPH-70.
• AC power outlet
• Local telephone line connection
• Access to dial-up Internet connection (via ISP) that is PPP compatible
• Account with a VoIP (Internet Telephone) service provider
2.2
Installation
1. Connect the handset to the DPH-70 with handset cord.
2. Plug one end of telephone cable (RJ-11) into the LINE port on the rear panel of DPH-70
and the other end into a working telephone wall jack.
3. Plug the AC power adaptor provided into an AC outlet and insert the power cord into the
connector marked “AC” on the rear panel of the device.
4. Lift the handset and listen for the dial tone that indicates the DPH-70 has been installed
properly. If you do not hear a dial tone, check that the power adaptor is plugged into a
live electrical outlet and that the power cord is pushed securely into the connector.
5. The DPH-70 is now ready for basic configuration as described in the next section.
Reminder: The DPH-70 needs Internet access and Internet calling card information to make
Internet phone calls. However, it can make normal PSTN phone calls without any configuration.
8
DPH-70 User’s Guide
3 Getting Started
After installation, DPH-70 is ready for configuration. You need to enter Internet Service Provider
(ISP) and Calling Card information to make and receive Internet phone calls. However, it can
make normal PSTN phone calls without any configuration. Refer to Appendix A to learn how to
enter alphanumeric and special characters required for user name and password.
Reminder: The DPH-70 identifies the end of each parameter by ‘#’. Please terminate each
parameter entry by pressing the ‘#’ key. For example, to enter the password as ‘123’ you need to
press ‘123#’.
3.1.1
ISP Information
The following Internet Service Provider (ISP) account information is required for dial-up Internet
connection. Refer to your Internet Service Provider’s card for this information.
Internet Access Telephone Number
User Name
Password
To enter these parameters, follow the steps below. The DPH-70 voice menu will guide you
through the configuration process.
1. Enter ‘∗123∗#’ to access the configuration menu.
2. Enter the configuration password. The default password is ‘12345’.
3. Enter ‘11’, to edit the ISP parameters. You will hear: “Please enter the ISP phone number
and terminate by ‘#’ button.”
4. Enter the Internet access phone number and terminate by pressing ‘#’ button. During
entry, the DPH-70 echoes the character pressed.
5. Terminate by pressing ‘#’ button. You will hear the message: “You entered xxxx, press ‘1’
to accept, ‘2’ to re-enter.” Press the appropriate number to continue.
6. Follow the voice menu to enter your ISP User Name and password. After ISP
configuration, the phone will play the main menu.
7. Enter ‘5’ to save the ISP information.
3.1.2
VoIP Calling Card Information
The following VoIP (Internet Telephone) calling card information is required for Internet phone
connection. Your VoIP service provider will provide these parameters. Refer to your calling card
for this information. After entering the calling card parameters, your Internet phone number will be
the same as user ID.
User ID
Password or PIN
To enter these parameters, follow the steps below and the voice menu from DPH-70.
1. Enter ‘∗123∗#’ to enter the configuration menu.
2. Enter the configuration password. The default password is ‘12345’.
3. Enter ‘21’, to edit the VoIP calling card parameters. The phone will prompt for calling card
configuration password.
4. Enter the password. If password entered is correct, it plays “Please enter the calling card
user ID and terminate by ‘#’ button”. Else, it plays “password entered is incorrect” and
returns to main menu.
5. Enter the calling card User ID and terminate by pressing ‘#’ button. During entry, the
phone will echo the character pressed.
9
DPH-70 User’s Guide
6. On termination with the ‘#’ button, you will hear: “You entered xxxx, press ‘1’ to accept, ‘2’
to re-enter.” Press the appropriate number to continue.
7. Follow the voice menu to enter the calling-card password. After calling card configuration,
phone will play the main menu.
8. Enter ‘5’ to save the calling card information.
After these basic configurations, the DPH-70 is ready to make and receive Internet phone calls as
described in the next section.
10
DPH-70 User’s Guide
4 Internet Phone Calls
After basic configuration, DPH-70 allows you to make and receive phone calls as described in
this section. The DIAL-UP button distinguishes Internet phone calls from normal PSTN calls. To
make an Internet phone call press the DIAL-UP button followed by the destination telephone
number. The DPH-70 supports a user-friendly dialing method as described below.
Reminder: You must have Internet access information and VoIP calling card information
configured in the DPH-70 to make and receive Internet calls.
4.1
4.1.1
To Make an Internet call
Normal dialing
As with a conventional phone, lift the handset, press the DIAL UP button and dial the other party’s
phone number followed by the ‘#’ key. For example, you press ‘dial-up12345#’ to call 12345
through the Internet. The DIAL-UP button tells the DPH-70 to connect to the Internet.
The DPH-70 will play a progress tone and establish contact with the called party. You will hear a
ring tone if the called phone is free and reachable. When the called party answers, you can carry
on a normal phone conversation. If anything goes wrong you will hear appropriate error
messages. Please refer to Appendix B: Troubleshooting for more information about the error
messages.
During the process of establishing an Internet call, DPH-70 connects to the Internet and then,
connects to the VoIP service provider. This may take some time, unlike a normal phone.
Reminder: The DPH-70 identifies the last digit of a phone number by ‘#’. Make sure to terminate
a phone number entry by pressing the ‘#’ key. If you don’t press any key for more than 5 seconds,
DPH-70 identifies it as the end of a phone number.
4.1.2
Multiple Calls
RECEIVE state allows you to make multiple Internet calls without connecting to the Internet each
time. You press DIAL-UP to go to RECEIVE state; please refer to the section on “Receiving
Internet Calls” for more details.
In this mode, you just dial the phone number followed by ‘#’. Since DPH-70 is already connected
to Internet, you do not press the DIAL-UP button before dialing a number. For example, you press
‘12345#’ to dial 12345 through Internet. It remains in call-receive state after the end of each call.
Please note that you cannot make normal PSTN call while DPH-70 is in RECEIVE state.
Warning: In RECEIVE state, DPH-70 is connected to the Internet and you will be charged for
Internet access. Do not leave the phone in RECEIVE mode unless you are expecting an Internet
phone call.
4.1.3
Special Dialing
A dial-up connection sometimes takes time to connect to the Internet depending on the Internet
access line availability and network congestion. Your DPH-70 is designed with a user-friendly
dialing method to help you in such situations.
Dial in the one-hand mode. When you press the DIAL UP button and dial a number without lifting
the handset, the speaker is turned ON. If the DPH-70 establishes contact with the called party it
11
DPH-70 User’s Guide
will play a ring-back tone. However, if the Internet access line is busy, the DPH-70 will retry 5
times before giving up.
During the process of making contact, the DPH-70 will play different call-progress tones (such as
progress, ring-back, or error tone) and cause the speaker LED to blink. After establishing contact,
it will play the ring-back tone and turn on the speaker LED. You can listen to call-progress tones
in the one-hand dialing mode, but you must use the handset to talk to the other party.
Warning: DPH-70 identifies the end of a phone number by ‘#’. Please terminate phone number
entry into DPH-70 by pressing the ‘#’ key. If you don’t press any key for more than 5 sec, DPH-70
identifies it as the end of a phone number.
4.2
Receiving Internet Calls
The DPH-70 must be connected to a VoIP server to receive phone calls. This is called RECEIVE
state. DIAL UP button enables and disables this state and the corresponding Dial-Up LED
indicates whether the DPH-70 is in the receive state. This button is operational even while using
the phone.
When you press the DIAL UP button, DPH-70 connects to the Internet and VoIP (Internet
Telephone) Service Provider. During this connection process, the phone will play the progress
tone and blink the DIAL UP LED. After connecting to the VoIP server, it will turn on the DIAL UP
LED and stop progress tone. It stays connected to the Internet for 15 minutes or until you cancel
it by pressing the DIAL UP button again.
If anything fails during this connection process, the DPH-70 will disconnect the modem, turn off
the Dial-Up LED, play an error message, and then revert to idle state. If the Internet access line is
busy it will retry 4 times before giving up.
Warning: In RECEIVE state, the DPH-70 is continuously connected to the Internet and you will
be charged for Internet access. Do not leave the phone in RECEIVE mode unless you are
expecting an Internet phone call.
4.3
Transferring Internet calls
The SIP signaling protocol in DPH-70 supports a call-transfer feature. This feature is not available
in H.323 signaling protocol.
This feature allows the user to transfer an Internet phone call to another phone connected to the
Internet. As with a conventional phone, you can transfer the call to another party. You flash the
hook switch (that means go on-hook and off-hook quickly), dial the phone number (terminated by
‘#’). The destination number will ring and on hanging up the phone, the call will be transferred to
the other party.
5 PSTN Phone Calls
DPH-70 can make and receive normal PSTN phone calls. When DPH-70 is not connected to the
Internet through the DIAL-UP button (RECEIVE state), it is known to be in idle state. In this state
it works as a normal phone, making and receiving PSTN phone calls. This feature does not need
any configuration.
12
DPH-70 User’s Guide
5.1
Making PSTN calls
To make an outgoing call, go off hook and dial the destination number, followed by #. For
example, you press 12345# to call 12345 through PSTN network. It plays various call progress
tone as in normal phone and plays ring back tone if the called party is free. DPH-70 establishes
the call on called party attending the call.
DPH-70 normally dials out with DTMF tones. However, if the phone number starts with a ‘$’, then
it dials out the phone number in pulse mode. For example, to dial 12345 in pulse mode, you press
$12345#.
DPH-70 has special supports for operation behind an EPABX. For example, you may have to dial
9 to get external dial tone and then dial the destination number. In this scenario, first dial ‘9#’ to
dial to EPABX and get external dial tone, then dial the destination number.
Reminder: DPH-70 identifies end of phone number by ‘#’. Please terminate phone number entry
by pressing ‘#’ key. If you don’t press any key for more than 5 sec, DPH-70 identifies it as end of
phone number.
5.2
Receiving PSTN calls
DPH-70 can receive any normal PSTN phone call when DPH-70 is not connected to the Internet
through the DIAL-UP button. It rings on incoming call and establishes call on lifting the handset.
Either party can disconnect the call by hanging up.
5.3
Transferring PSTN calls
This feature allows the user to transfer a PSTN phone call to any PSTN phone. To transfer the
call, you flash the hook for a short period and dial the destination number followed by ‘#’. The
destination number will ring and on off-hook the call transfer will be complete.
13
DPH-70 User’s Guide
6 DPH-70 Configuration
The DPH-70 voice menu helps you through the configuration process. You can enter the
configuration menu by pressing the key sequence ‘∗123∗’ and terminate with a hash (#) key when
DPH-70 is in idle state.
1
ISP
Parameters
Phone Number
User Name
Password
2
3
ABC
4
DEF
Calling Card
Parameters
User ID
Password
VoIP server address
Calling card
configuration password
1.
2.
3.
4.
5.
6.
7.
8.
9.
5
GHI
JKL
Review
Configuration
Save
& Quit
Internet Access Phone Number
ISP User Name
ISP Password
Calling Card User ID
Calling Card Password
VoIP Server Address
Extended
Menu
Configuration Password
Software Server Address
Country Code
Language
Service Provider
Software Version
Volume Control
Review Configuration
Exit to Main Menu
Configuration Password
Software Server Address
Country Code
Language
VoIP Service Provider
Software Version
Volume level
DPH-70 will ask for password on entering configuration menu. Since the configuration information
contains valuable information it is password protected. If you don’t remember your password, you
can reset DPH-70 to dedault password as described in Loading factory defaults. The default
password is ‘12345’.
Reminder: The DPH-70 identifies the end of a parameter by ‘#’. Please terminate each
parameter entry into DPH-70 by pressing the ‘#’ key.
14
DPH-70 User’s Guide
DPH-70 configuration menu is shown above. It has five options in the main menu and seven
options in the extended menu. Each of them is described below. The configurable parameters are
shown in bold letters. DPH-70 plays the current value of each parameter and allows you to edit
or skip to next parameter. After entering a parameter value, the voice prompt plays it back for
verification.
After password verification, DPH-70 will play the main menu as below.
“Press
‘1’ to enter ISP parameters,
‘2’ to enter calling card parameters,
‘3’ to enter extended menu,
‘4’ to review configuration parameters,
‘5’ to save & quit.”
Note:
If power goes off while you are configuring, the phone works with the last saved
parameters.
If the phone is idle more than 90 seconds, DPH-70 will accept the keys entered and go to
next state.
If you leave the phone without completing the configuration it will go back to idle state
without saving the parameters.
6.1
ISP Parameters
The DPH-70 needs to connect to the Internet to make Internet phone calls. The following
information should be configured in your phone to connect to the Internet and make calls. The
user will get this information from the Internet Service Provider (ISP). Please note that the DPH70 will not work without this information.
ISP Phone Number
This is the phone number to which the DPH-70 will dial-up to connect to the Internet. The Internet
access phone number can be a maximum of 20 digits. If you enter more digits and try to save,
you will hear: “ The parameter you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip.” Press
‘1’ or ‘2’ appropriately.
The DPH-70 normally dials out with DTMF tones. However, if the Internet access phone number
is configured to start with a ‘$’, then the phone will dial out in pulse mode.
DPH-70 has special supports for operation behind an EPABX. In some scenarios, you may have
to introduce a delay after dialing external access number or wait for secondary dial tone. A ‘.’ (dot)
in phone number will introduce a delay and a ‘_’ (under-score) will look for secondary dial tone.
For example, 9.6788341 will introduce a small delay after dialing 9, before dialing other digits.
ISP User Name
This is the name used for identifying the user to the Internet Service Provider (ISP). It can have a
mix of digits, lower and upper case letters, and special characters; it can have a maximum of 30
characters. Please refer to Appendix A: Entering alphanumeric and special characters to enter
special characters.
15
DPH-70 User’s Guide
ISP Password
The password used for verifying the user to the Internet Service Provider (ISP). It can have a mix
of digits, upper and lower case letters, and special characters; it can have a maximum of 30
characters. Please refer to Appendix A: Entering alphanumeric and special characters to enter
special characters.
6.2
Calling Card Parameters
The following information is required for DPH-70 to make and receive Internet phone calls. The
user will get this information from the VoIP (Internet Telephone) service provider. Please note that
the DPH-70 will not work without this information.
Calling Card User ID
This is the Internet phone number or user ID assigned to you. It can have a maximum of 30
characters. This information is required to verify the calling card user identity to the VoIP (Internet
Telephone) Service Provider.
Calling Card Password
This information is required to verify the calling card user identity to the VoIP (Internet Telephone)
Service Provider. It can have a maximum of 30 characters.
VoIP Server Address
This is the IP address where VoIP (Internet Telephone) Server is running. It can be a valid IP
address like 198.62.73.101 or a valid domain name like sip.dlink.com. The domain name can
have a maximum of 30 characters, including ‘dots’. Default server address is sip.dlink.co.in
VoIP server address is of the form xxx.xxx.xxx.xxx where xxx is between 0 and 255. If the
entered number is invalid, phone prompts with a message: “The parameter you have entered is
incorrect, Press ‘1’ to edit, ‘2’ to skip”.
Calling Card configuration Password
This is the password for accessing and configuring the calling card information. It can have
maximum of 30 characters. Default is “abcd”. The user is advised to change this value. If you
forget this password, reset the phone to factory values and configure the phone again.
6.3
Review Configuration
This option will play the current information for all parameters in main menu. You will hear:
“ISP Phone number is xxxx,
ISP User name is xxxx,
ISP Password is xxxx,
Calling Card user ID is xxxx,
Calling Card password is xxxx,
VoIP server address is xxx.xxx.xxx.xxx”
After playing this message, it prompts with the main menu.
16
DPH-70 User’s Guide
6.4
Save and Exit
This option saves all the information entered in the configuration and exits from the configuration
option. You can leave the configuration without saving the information by replacing the handset or
switching the speaker off.
6.5
6.5.1
Extended Menu
Configuration Password
Internet access and calling card parameters are valuable information and can be misused. To
protect against this, the DPH-70’s configuration module is password-protected. It can have
maximum of 30 characters. Default is "12345". The user is strongly advised to change this value.
If you forget this password, reset the phone to factory values and configure the phone again.
6.5.2
Software server address
The latest DPH-70 software can be downloaded from this address. The address can be a valid IP
address like 198.62.73.101 or a valid domain name like dph70.cityonlines.com. The domain
name can have maximum of 30 characters, including ‘dots’. Default server address is
dph70.cityonlines.com (or 202.62.83.106).
6.5.3
Country Code
Following is a list of countries supported with their respective codes
Table 1 Country Codes
Country
Brazil
China
India
Korea
Malaysia
Mexico
South Africa
Taiwan
USA
Others (India)
Code
0
1
2
3
4
5
6
7
8
9
If you enter a value other than those listed, the phone prompts with a message “The parameter
you have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip.” Choose appropriately.
Based on the country code selection, the various tones and modem software will vary. Default
country code is 2 (India). If you change it to some other country than yours, the phone may not be
able to make calls and you will hear some error messages. So please be sure to select the
correct country code.
6.5.4
Language Support
The DPH-70 can play voice prompts in many languages. Following is the list of languages
supported with their respective codes.
17
DPH-70 User’s Guide
Table 2 Languages
Language
Default
English
Hindi
Code
0
1
2
If you enter other than the listed value, the phone prompts with a message “The parameter you
have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip.” Choose appropriately.
If you change the language code, please do a software upgrade as described in Upgrading
Software section.
6.5.5
VoIP Service Provider
DPH-70 works with many service providers. Following is the list of service providers supported
with their respective codes.
Table 3 Service Providers
Service Provider
Default
VSNL
SatyamOnLine
Pioneer Online
Code
0
1
2
3
If you enter other than the listed value, the phone prompts with a message “The parameter you
have entered is incorrect, Press ‘1’ to edit, ‘2’ to skip.” Choose appropriately.
If you change the service provider code, please do a software upgrade as described in Upgrading
Software section.
6.5.6
Software version number
This option plays the current software version in DPH-70. It will change if you download a newer
version of software from the Internet.
6.5.7
Volume Control
The volume level can vary depending on the VoIP gateway of your VoIP service provider. This
option allows configuration of volume levels for Internet (VoIP) and PSTN calls. DPH-70 has
separate volume control for Internet and PSTN calls. You can select a level in the range of 1 – 5
to adjust the volume level. The default values are 3 for VoIP calls and 3 for PSTN calls.
6.5.8
Review Configuration
This option plays current information for all parameters in the extended menu:
“Configuration password is x
Software server address is x
Country Code is x
Language selected is x
VoIP Service provider is x
Current software version is x”
VoIP volume level is x
18
DPH-70 User’s Guide
PSTN volume level is x”
After playing this message, it prompts with the extended menu.
6.5.9
Exit to Main Menu
This option takes you to the main menu. You need to save the information entered in the
Extended Menu by selecting ‘Save and Exit’ in the Main Menu.
19
DPH-70 User’s Guide
7 Additional Features
7.1
Upgrading Software
The DPH-70 has a facility to upgrade its software remotely through the Internet at no cost to you.
Software can be downloaded when the phone is in RECEIVE state or when not in use.
On pressing ‘∗456∗#’, the phone connects to the Internet and downloads the software. During the
download process, DPH-70 will play progress tone and blink the SHIFT LED. After a successful
download, the phone restarts with the newer software. If the download fails for some reason, the
phone will continue working with the earlier software. You can check the current software version
through configuration menu.
D-Link will release the latest DPH-70 software in its website at http://www.dlink.co.in along with
the server IP address for the latest software download. This information must be entered into
DPH-70 through the configuration menu.
Note: On pressing ‘*456*#’, DPH-70 will ask for confirmation.
7.2
Loading factory defaults
If it is required to reset DPH-70 and start with default configuration parameters, you can do so by
pressing ‘∗789∗#’ while the phone is in idle state. The phone restarts in few seconds with the
default parameters. Default configuration password is ‘12345’. The phone needs to be configured
again for Internet access and calling card information before it can be used.
Note: On pressing ‘*789*#’, the DPH-70 will ask for confirmation.
20
DPH-70 User’s Guide
Appendix A: Entering alphanumeric and special characters
The section describes how to enter digits, upper and lower case alphabets, and special
characters using the DPH-70 keypad shown below.
7.3
Entering Digits
•
Press any digit key once to enter the corresponding digit.
Example:
7.4
To enter 4, press key 4 once.
Entering Small (lower-case) Letters
•
•
•
•
•
Press a digit key twice to enter the first character written on that key.
Press thrice to enter the second character written on that key
Press four times to enter the third character written on that key.
Press five times to enter the fourth character written on that key.
If the key is pressed more than above mentioned times, it accepts the last letter written
on that key.
Examples:
To enter a, press key 2 two times.
To enter e, press key 3 three times.
To enter z, press key 9 five times.
NOTE: Press the appropriate key firmly, specified number of times, in quick succession to enter
alphabets.
21
DPH-70 User’s Guide
7.5
Entering Capital (upper-case) Letters
You need to press a SHIFT button and a digit key, the specified number of times, to enter the
capital letters marked on digit keys. SHIFT LED turns on after SHIFT button is pressed and turns
off after the digit key is pressed.
•
•
•
Press a SHIFT button and then the digit key, the following number of times to enter the
capital letters.
o Twice to enter the capital of the first letter written on that key.
o Thrice to enter the capital of the second letter written on that key.
o Four times to enter the capital of the third letter written on that key.
o Five times to enter the capital of the fourth letter written on that key.
If the key is pressed once after SHIFT button is pressed, it accepts the corresponding
digit.
If the key is pressed more than above mentioned times after the SHIFT button is pressed,
it accepts as a last capital letter written on that key.
Examples:
To enter A, press SHIFT followed by key 2 two times.
To enter E, press SHIFT followed by key 3 three times.
To enter Z, press SHIFT followed by key 9 five times.
NOTE: Press the appropriate key firmly, specified number of times, in quick succession to enter
alphabets.
7.6
Entering Special Characters
Press the DIAL UP button and then press the corresponding key shown in the table below to
enter special characters. DIAL UP LED turns on after pressing the DIAL UP button and turns
off after accepting a special character.
Special
Character
@
.
_
$
&
/
:
Description
“Backspace”
“At ”
“Dot”
“Hyphen”
“Underscore”
“Dollar”
“Ampersand”
“Slash”
“Colon”
DIAL UP
followed by:
0
1
2
3
4
5
6
7
8
Note: Backspace can be used to delete an unwanted character. It will delete the last entered
character.
Examples:
To enter @, press DIAL UP followed by key 1.
To enter ., press DIAL UP followed by key 2.
To delete the last character entered, press DIAL UP followed by key 0.
22
DPH-70 User’s Guide
8 Appendix B: Troubleshooting
DPH-70 will play the following error messages corresponding to different error conditions. These
messages aid in troubleshooting any problems.
All outgoing calls are PSTN calls. It does not dial in Internet mode.
To make a call in Internet mode, you have to press the DIAL-UP button first. Please refer to
the user manual for more details. If you don’t press DIAL-UP, the DPH-70 will dial out in
PSTN mode.
“Please configure the phone and try again”
This message is played if you try to use DPH-70 without configuring important parameters. You
need to configure the Internet Service Provider (ISP) access parameters and VoIP (Internet
Telephone) calling card parameters to use the phone.
“Please check the phone line and try again”
This message is played if DPH-70 is not connected to the phone line properly. Please check the
phone line connection and try again. Test the phone line with a normal phone if the problem
persists.
If DPH-70 is behind EPBX you may have to program DPH-70 to look for secondary dial tone or
introduce a delay. Please refer to the configuration section for more information.
“Password entered is incorrect. Try again”
If invalid password is entered to access configuration state, this message is played.
“The ISP line is busy, please call after some time”
This message is played when the Internet access line is busy. This may happen during peak
hours.
“The ISP server is not responding”
Heard when the Internet access modem is not responding properly. If this happens please check
the Internet access phone number and country code in the configuration menu. If you call Internet
access phone number from a normal phone you will hear modem noise.
“ISP connection could not be established, try later”
Played when Internet access server is down. Please contact the ISP customer service or try
again after some time.
“Please check your ISP parameters and try again”
This message is played when the configured ISP user name and/or password is incorrect. Please
verify the ISP user name and password.
23
DPH-70 User’s Guide
“Bad phone line, please contact customer support”
Indicates that your phone line may not connect to the Internet at sufficient speed to establish
Internet phone calls. Please try another phone line or contact customer support.
“Please check your calling card parameters and try again”
This message is played when the configured calling card information is incorrect. Please verify
the calling card parameters. This may also be due to VoIP server not responding. You may try
again if you are sure of stored calling card parameters.
“The number you have dialed is not locatable, please check the number”
This message is played when the called phone number does not exist or is not ready to receive
calls.
“The number you have called is busy, please call after some time”
This message is played when the called phone is busy.
“Incorrect value. Press ‘1’ to edit, ‘2’ to skip”
This message is played when invalid information is entered as part of configuration.
Fast error tone for a short period while disconnecting phone
This error tone is played while the modem disconnects from the Internet. This process takes a
short time and the phone is inaccessible during this period.
24
DPH-70 User’s Guide
9
Appendix C: DPH-70 Product Specifications
General
Product Feature
Description
Model
VoIP signaling protocol
Data Modem Standard
Power Adapter
Power consumption
DPH-70B1
H.323 Version 2 or SIP (RFC2543)
V.34
9V 1000mA AC Adapter (120-240V AC).
5W max.
Hardware Specifications
Product Feature
Description
One Port for Telephone line
connection
RJ11
Dial Up LED
Shift LED
Speaker LED
Speaker button
Shift button
Dial Up button
Redial button
Number Keys
Speaker Volume Adjustment
Handset Volume Adjustment
The SmartDAA Interface feature that reliably operates
without drawing power from the line
Remarks
Color
Timing
Green
Steady
Indicates if the
phone is in receive
state or not
Used in
Red
Steady
configuration to
enter upper case
letters
Indicates if speaker
Red
Steady
is on or off.
Press this button to turn on and off the speaker for onehanded dialing.
Used for entering upper case letters during configuration
state.
Makes the phone ready to receive IP phone calls or to
make multiple calls.
Redials the last dialed number.
0 to 9, #, ∗:
These are normal number keys and can be used for
dialing or entering digits.
Alphanumeric
Alphanumeric and special characters can also be entered
through keypad.
Speaker volume can be adjusted using this facility.
This can be used for adjusting the volume on the handset
Software Specifications
Voice Codec
G.723.1 is available for modem connection speeds of 16.8 Kbps or
above.
25
DPH-70 User’s Guide
G.729A/AB is available for modem connection speeds of 24 Kbps or
above.
Algorithms minimize the bandwidth requirements.
Voice activity detection,
Silence suppression,
Comfort noise generation
Internet protocol
PPP
TFTP
Reset to factory defaults
IP (RFC0791)
TCP (RFC0793)
UDP (RFC0768)
RTP/RTCP (RFC1889, RFC1890)
SDP (RFC2327)
(RFC1661) To connect to ISP via dial-up connection.
Trivial File Transfer Protocol is used for firmware download.
After pressing a factory reset key sequence, the phone restarts with
all default parameters. The access sequence is ‘∗789∗#’.
Digits, Special characters and all letters can be entered.
Configuration using
Keypad
User authentication
Password protection for configuration menu.
Configuration password
Default password is ‘12345’.
Calling card configuration
password
Configuration menu
Default password is ‘abcd’
Software upgrade
Access code is ‘∗456∗’.
Factory reset
Access code is ‘∗789∗’.
VoIP call volume level
Default is 3
PSTN call volume level
Default is 3
VoIP server address
Default is sip.cityonlines.com (or 202.62.83.106)
Software server address
Default is dph70.cityonlines.com (or 202.62.83.106)
Access code is ‘∗123∗’.
Safety / EMI Specifications
Standards Compliance
Operating Temperature
Storage Temperature
Humidity Range
Dimensions
Weight
FCC Class B part 15 and part 68
0 °C to 40 °C
-10 °C to 60 °C
5% to 95% Non-condensing
52 (H) x 206 (L) x 103 mm (without handset)
800gms
26
DPH-70 User’s Guide
Offices
Australia
D-Link Australia
1 Giffnock Avenue, North Ryde, NSW 2113,
Sydney, Australia
TEL: 61-2-8899-1800 FAX: 61-2-8899-1868
TOLL FREE (Australia): 1800-177100
URL: www.dlink.com.au
E-MAIL: support@dlink.com.au & info@dlink.com.au
Brazil
Canada
Chile
China
Denmark
Egypt
D-Link Brasil Ltda.
Edificio Manoel Tabacow Hydal,
Rua Tavares Cabral 102 Sala 31, 05423-030
Pinheiros, Sao Paulo, Brasil
TEL: (55 11) 3094 2910 to 2920 FAX: (55 11) 3094 2921
E-MAIL: efreitas@dlink.cl
D-Link Canada
2180 Winston Park Drive, Oakville,
Ontario, L6H 5W1 Canada
TEL: 1-905-829-5033 FAX: 1-905-829-5095
TOLL FREE: 1-800-354-6522 URL: www.dlink.ca
FTP: ftp.dlinknet.com E-MAIL: techsup@dlink.ca
D-Link South America (Sudamérica)
Isidora Goyenechea 2934 Of. 702, Las Condes Fono,
2323185, Santiago, Chile, S. A.
TEL: 56-2-232-3185 FAX: 56-2-232-0923
URL: www.dlink.cl
E-MAIL: ccasassu@dlink.cl & tsilva@dlink.cl
D-Link China
15th Floor, Science & Technology Tower,
No.11, Baishiqiao Road, Haidan District, 100081 Beijing, China
TEL: 86-10-68467106 FAX: 86-10-68467110
URL: www.dlink.com.cn
E-MAIL: liweii@digitalchina.com.cn
D-Link Denmark
Naverland Denmark, Naverland 2, DK-2600 Glostrup, Copenhagen, Denmark
TEL: 45-43-969040 FAX:45-43-424347
URL: www.dlink.dk E-MAIL: info@dlink.dk
D-Link Middle East
7 Assem Ebn Sabet Street, Heliopolis, Cairo, Egypt
TEL: 202-245-6176 FAX: 202-245-6192
URL: www.dlink-me.com
E-MAIL: support@dlink-me.com & fateen@dlink-me.com
Finland
France
Germany
D-Link Finland
Pakkalankuja 7A, FIN–0150 Vantaa, Finland
TEL: 358-9-2707-5080 FAX: 358-9-2707-5081
URL: www.dlink-fi.com
D-Link France
Le Florilege, No. 2, Allée de la Fresnerie,
78330 Fontenay-le-Fleury, France
TEL: 33-1-3023-8688 FAX: 33-1-3023-8689
URL: www.dlink-france.fr
E-MAIL: info@dlink-france.fr
D-Link Central Europe (D-Link Deutschland GmbH)
Schwalbacher Strasse 74, D-65760 Eschborn, Germany
TEL: 49-6196-77990 FAX: 49-6196-7799300
27
DPH-70 User’s Guide
URL: www.dlink.de
BBS: 49-(0) 6192-971199 (analog)
BBS: 49-(0) 6192-971198 (ISDN)
INFO: 00800-7250-0000 (toll free)
HELP: 00800-7250-4000 (toll free)
REPAIR: 00800-7250-8000 E-MAIL: info@dlink.de
India
D-Link India
Plot No.5, Bandra-Kurla Complex Rd., Off Cst Rd.,
Santacruz (East), Mumbai, 400 098 India
TEL: 91-022-2652-6696/6578/6623
FAX: 91-022-2652-8914/8476
URL: www.dlink-india.com & www.dlink.co.in
E-MAIL: service@dlink.co.in ; voip@dlink.co.in
Italy
D-Link Mediterraneo Srl/D-Link Italia
Japan
D-Link Japan
Netherlands
Norway
Via Nino Bonnet n. 6/B, 20154, Milano, Italy
TEL: 39-02-2900-0676 FAX: 39-02-2900-1723
URL: www.dlink.it E-MAIL: info@dlink.it
10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan
TEL: 81-3-5434-9678 FAX: 81-3-5434-9868
URL: www.d-link.co.jp E-MAIL: kida@d-link.co.jp
D-Link Benelux
Fellenoord 130 5611 ZB, Eindhoven, The Netherlands
TEL: 31-40-2668713 FAX: 31-40-2668666
URL: www.d-link-benelux.nl & www.dlink-benelux.be
E-MAIL: info@dlink-benelux.nl & info@dlink-benelux.be
D-Link Norway
Waldemar Thranesgate 77, 0175 Oslo, Norway
TEL: 47-22-99-18-90 FAX: 47-22-20-70-39 SUPPORT: 800-10-610
URL: www.dlink.no
Russia
Singapore
D-Link Russia
Michurinski Prospekt 49, 117607 Moscow, Russia
TEL: 7-095-737-3389 & 7-095-737-3492
FAX: 7-095-737-3390 URL: www.dlink.ru
E-MAIL: vl@dlink.ru
D-Link International
1 International Business Park, #03-12 The Synergy,
Singapore 609917
TEL: 6-6774-6233 FAX: 6-6774-6322
E-MAIL: info@dlink.com.sg URL: www.dlink-intl.com
South Africa
D-Link South Africa
Spain
D-Link Iberia (Spain and Portugal)
Sweden
Unit 2, Parkside, 86 Oak Avenue, Highveld Technopark,
Centurion, Gauteng, South Africa
TEL: 27-12-665-2165 FAX: 27-12-665-2186
URL: www.d-link.co.za E-MAIL: attie@d-link.co.za
Sabino de Arana, 56 bajos, 08028 Barcelona, Spain
TEL: 34 93 409 0770 FAX: 34 93 491 0795
URL: www.dlink.es E-MAIL: info@dlink.es
D-Link Sweden
P. O. Box 15036, S-167 15 Bromma, Sweden
TEL: 46-8-564-61900 FAX: 46-8-564-61901
URL: www.dlink.se E-MAIL: info@dlink.se
Taiwan
D-Link Taiwan
2F, No. 119 Pao-chung Road, Hsin-tien, Taipei, Taiwan
TEL: 886-2-2910-2626 FAX: 886-2-2910-1515
28
DPH-70 User’s Guide
URL: www.dlinktw.com.tw E-MAIL: dssqa@tsc.dlinktw.com.tw
Turkey
D-Link Middle East
U.A.E.
D-Link Middle East
U.K.
D-Link Europe (United Kingdom) Ltd
Deniz Bilgisayar, Buyukdere Cad. Naci Kasim Sk., No. 5
Mecidiyekoy, Istanbul, Turkey
TEL: 90-212-213-3400 FAX: 90-212-213-3420
E-MAIL: smorovati@dlink-me.com
CHS Aptec (Dubai), P.O. Box 33550 Dubai, United Arab Emirates
TEL: 971-4-366-885 FAX: 971-4-355-941
E-MAIL: Wxavier@dlink-me.com
4th Floor, Merit House, Edgware Road, Colindale, London
NW9 5AB United Kingdom
TEL: 44-020-8731-5555 SALES: 44-020-8731-5550
FAX: 44-020-8731-5511 SALES: 44-020-8731-5551
BBS: 44 (0) 181-235-5511
URL: www.dlink.co.uk E-MAIL: info@dlink.co.uk
U.S.A.
D-Link U.S.A.
53 Discovery Drive, Irvine, CA 92618, USA
TEL: 1-949-788-0805 FAX: 1-949-753-7033
INFO: 1-800-326-1688 URL: www.dlink.com
E-MAIL: tech@dlink.com & support@dlink.com
29
DPH-70 User’s Guide
Registration Card
Print, type or use block letters.
Your name: Mr./Ms _____________________________________________________________________________
Organization: ________________________________________________ Dept. ____________________________
Your title at organization: ________________________________________________________________________
Telephone: _______________________________________ Fax:________________________________________
Organization's full address: ______________________________________________________________________
____________________________________________________________________________________________
Country: _____________________________________________________________________________________
Date of purchase (Month/Day/Year): _______________________________________________________________
Product Model
Product Serial
No.
* Product installed in type of
computer (e.g., Compaq 486)
* Product installed in
computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name: ______________________________________________________________________________
Telephone: _______________________________________ Fax:________________________________________
Reseller's full address: _________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
Home
Office
Travel
Company Business
Home Business
Personal Use
2. How many employees work at installation site?
1 employee
2-9
10-49
50-99
100-499
500-999
1000 or more
3. What network protocol(s) does your organization use ?
XNS/IPX
TCP/IP
DECnet
Others_____________________________
4. What network operating system(s) does your organization use ?
D-Link LANsmart Novell NetWare NetWare Lite SCO Unix/Xenix PC NFS 3Com 3+Open
Banyan Vines DECnet Pathwork Windows NT Windows NTAS Windows '95
Others__________________________________________
5. What network management program does your organization use ?
D-View HP OpenView/Windows HP OpenView/Unix SunNet Manager
NetView 6000 Others________________________________________
Novell NMS
6. What network medium/media does your organization use ?
Fiber-optics Thick coax Ethernet Thin coax Ethernet 10BASE-T UTP/STP
100BASE-TX 100BASE-T4 100VGAnyLAN Others_________________
7. What applications are used on your network?
Desktop publishing Spreadsheet Word processing CAD/CAM
Database management Accounting Others_____________________
8. What category best describes your company?
Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate
Retail/Chainstore/Wholesale Government Transportation/Utilities/Communication VAR
System house/company Other________________________________
Manufacturing
9. Would you recommend your D-Link product to a friend?
Yes
No
Don't know yet
10.Your comments on this product?
__________________________________________________________________________________________
__________________________________________________________________________________________
30
DPH-70 User’s Guide
31