Motorola LS2208-SR20001R Instruction manual

LS2208
NEGRO
Quick Start Guide
STEP 1 - ATTACH CABLE TO SCANNER
http://www.motorola.com/ls2208
Remove Cable (to change interface)
Attach Cable
POST IN WORK AREA
PANTONE 285
See Product Reference Guide for detailed information
STEP 2 -CONNECT CABLE TO A HOST
NOTE: Cables may vary depending on configuration.
USB
Keyboard Wedge
RS-232
IBM 46XX
STEP 3 - SET UP INTERFACE (Scan Host Bar Codes)
Important: Out of box, Keyboard Wedge and USB interfaces require no bar code scan setup. Bar codes are provided for complex programming or interface changes.
USB
Keyboard Wedge
RS-232
Scan ONE of the bar codes below
Scan ONE of the bar codes below
Scan ONE of the bar codes below
IBM HAND-HELD USB
IBM AT Notebook
OPOS/JPOS
HID KEYBOARD EMULATION
IBM PC/AT and IBM PC COMPATIBLE
STANDARD RS-232
IBM 46XX
Scan ONE of the bar codes below
ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)
To add an ENTER key after scanned data, scan all THREE bar codes below in numerical order.
1
2
3
SCAN OPTIONS
<DATA><SUFFIX>
ENTER
ADD A TAB KEY
To add a Tab key after scanned data, scan all THREE Enter key bar codes above in numerical order then scan all FIVE bar codes below in numerical order.
1
2
3
4
5
SCAN SUFFIX
7
0
0
9
HANDS FREE STAND
OPTIMUM
SCANNING
SET DEFAULTS
123SCAN2
Return to Factory Defaults
123Scan2 is an easy-to-use, PC-based software
tool that enables rapid and easy customized
setup via a bar code or USB cable. For more
information, visit:
http://www.motorola.com/123Scan2.
012345
SET DEFAULTS
012345
SCANNER INDICATIONS
LED Indications
Off
Troubleshooting
Green
Scanner is on and ready to scan,
or no power to scanner
Bar code is
successfully decoded
Red
Scanner not working
Transmission error
Standard Use
Short medium beep
Power up
Bar code decoded
Parameter Menu Scanning
High/low/high/low beep
No power to scanner
Check system power;
ensure power supply,
if required, is connected
Beeper Indications
Low/medium/high beep
TROUBLESHOOTING
High/low beep
Successful
parameter setting
Correct programming
sequence performed
4 long low beeps
Transmission error detected,
data is ignored
Low/High beep
Scanned data incorrectly displayed on host
Incorrect interface cable used
Ensure that correct
interface cable is used
Interface/power cables are loose
Ensure all cable connections
are secure
Scanner decoding bar code, but data not transmitting to host
Scanner not programmed for correct host interface
Interface cable is loose
Ensure all cable connections
are secure
Scan appropriate host parameter bar codes
Incorrect programming sequence
or ’Cancel’ bar code scanned
Scanner not programmed for correct host interface
Scan appropriate host parameter bar codes
Scanner not decoding bar code
Scanner not programmed
Bar code unreadable
for bar code type
Ensure scanner is programmed
to read type of bar code being
scanned
Distance between scanner
and bar code incorrect
Ensure bar code not defaced;
try scanning test bar code
of same bar code type
Move scanner closer to or
further from bar code
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
Avoid Extreme Wrist Angles
Avoid Bending
Avoid Reaching
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of
ergonomic injury follow the recommendations below.
Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety
programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
REGULATORY INFORMATION
© MOTOROLA, INC. 2012 All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or
use of any product, circuit, or application described herein. No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination,
system, apparatus, machine, material, method, or process in which Motorola products might be used.
An implied license exists only for equipment, circuits, and subsystems contained in Motorola products.
Laser Labels
ENGLISH
CLASS 1
CLASS 2
Power Supply
Use ONLY a Motorola approved UL LISTED ITE (IEC/EN 60950-1, LPS) power supply with electrical ratings:
output 5 Vdc, min 850mA with a maximum ambient temperature of at least 50 degrees C. Use of an alternative
power supply will invalidate any approvals given to this unit and may be dangerous.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorolasolutions.com/warranty
Service Information
POST IN WORK AREA
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a
problem with the equipment, they will contact the Motorola Solutions Support at:
http://www.motorolasolutions.com/support
Regulatory Information
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:
CLASS 1 LASER PRODUCT
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
HEBREW
This device is approved under the Symbol Technologies, Inc. brand: Symbol Technologies is a wholly
owned subsidiary of Motorola Solutions, Inc. (collectively ”Motorola”). This guide applies to Model
Number LS2208. All Motorola devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://www.motorolasolutions.com/support.
DANISH / DANSK
KLASSE 1 KLASSE 1 LASERPRODUKT
KLASSE 2 LASERLYF
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
DUTCH / NEDERLANDS
KLASSE 1 KLASSE-1 LASERPRODUKT
KLASSE 2 LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
ITALIAN / ITALIANO
CLASSE 1 PRODOTTO AL LASER DI CLASSE 1
CLASSE 2 LUCE LASER
NON FISSARE IL RAGGIOPRODOTTO
AL LASER DI CLASSE 2
NORWEGIAN / NORSK
KLASSE 1 LASERPRODUKT, KLASSE 1
KLASSE 2 LASERLYS IKKE STIRR INN ILYSSTRÅLEN
LASERPRODUKT, KLASSE 2
FINNISH / SUOMI
LUOKKA 1 LUOKKA 1 LASERTUOTE
LUOKKA 2 LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
FRENCH / FRANÇAIS
CLASSE 1 PRODUIT LASER DE CLASSE 1
CLASSE 2 LUMIERE LASER
NE PAS REGARDER LE RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
PORTUGUESE / PORTUGUÊS
CLASSE 1 PRODUTO LASER DA CLASSE 1
CLASSE 2
LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
GERMAN / DEUTSCH
KLASSE 1 LASERPRODUKT DER KLASSE 1
KLASSE 2 LASERSTRAHLEN
NICHT DIREKT IN DEN LASERSTRAHL
SCHAUEN
LASERPRODUKT DER KLASSE 2
SWEDISH / SVENSKA
KLASS 1
LASERPRODUKT KLASS 1
KLASS 2
LASERLJUS STIRRA INTE MOT STRÅLEN
LASERPRODUKT KLASS 2
SPANISH / ESPAÑOL
CLASE 1
PRODUCTO LASER DE LA CLASE 1
CLASE 2
LUZ LASER
NO MIRE FIJAMENTE EL HAZ
PRODUCTO LASER DE LA CLASE 2
Laser Devices
Symbol products using lasers complies with 21CFR1040.10 and 1040.11 except for
deviations pursuant to laser notice No. 50, dated June 24, 2007 and IEC 60825-1
(Ed. 2.0), EN60825-1:2007. The laser classification is marked on one of the labels on the
product. Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose.
The following statement is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser
is not known to be harmful.
Radio Frequency Interference Requirements
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in residential installation. This equipment
FOR HOME OR OFFICE USE
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Tested to comply
with FCC Standards
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
For Australia Only
This warranty is given by Motorola Solutions Australia Pty Limited (ABN16 004 742 312) of Tally Ho Business
Park, 10 Wesley Court. Burwood East, Victoria. Our goods come with guarantees that cannot be excluded
under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure. Motorola Solutions Australia’s limited warranty above is in addition to any rights and remedies you may
have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia
at 1800 457 439. You may also visit our website:
http://www.motorola.com/Business/XA-EN/Pages/Contact_Us for the most updated warranty terms.
Ukraine
Motorola, Inc. One Motorola Plaza , Holtsville, New York 11742-1300, USA
http://www.motorolasolutions.com
Дане обладнаннявідповідає вимогам технічного регламенту №1057, № 2008 щодо використання
деяких небезпечних речовин в електричних та електронних пристроях.на обмеженнях
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Motorola hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC, 2006/95/EC
and 2011/65/EU. A Declaration of Conformity may be obtained from the following web site:
http://www.motorolasolutions.com/doc
Japan (VCCI) - Voluntary Control Council for Interference
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準に基づくクラス B 情
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks
or registered trademarks of Motorola Trademark Holding, LLC and are used under license.
All other trademarks are the property of their respective owners. © Motorola, Inc. 2012, Inc.
All rights reserved.
報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この装置がラ
ジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
72-71882-01 Revision E December 2012
LS2208
cause radio interference. Install and use the equipment according to the instruction manual.
http://www.motorola.com/ls2208