Siemens SIMATIC Box PC 620 Specifications

Preface, Contents
Important Information
1
Welcome to the Box PC 620
2
Box PC 620
Setting-up and Operating
the Box PC 620
3
Manual
Box PC 620 Expansions
4
Configuring the Box PC 620
5
Error Diagnosis
6
Hardware Information
7
Reinstallation of the Software
8
SIMATIC
Valid for devices with the order number
6ES7647-5...
Appendix
Guidelines for ESD
A
Technical Specifications
B
Glossary, Index
Edition 03/2002
A5E00131465-01
Safety Guidelines
This manual contains notices intended to ensure personal safety, as well as to protect the products and
connected equipment against damage. These notices are highlighted by the symbols shown below and
graded according to severity by the following texts:
!
!
!
Danger
indicates that death, severe personal injury or substantial property damage will result if proper precautions
are not taken.
Warning
indicates that death, severe personal injury or substantial property damage can result if proper
precautions are not taken.
Caution
indicates that minor personal injury can result if proper precautions are not taken.
Caution
indicates that property damage can result if proper precautions are not taken.
Notice
draws your attention to particularly important information on the product, handling the product, or to a
particular part of the documentation.
Qualified Personnel
Repair, maintenance and servicing of device only to be carried out by qualified personnel. Qualified
persons are defined as persons who are authorized to commission, to ground and to tag circuits,
equipment, and systems in accordance with established safety practices and standards.
Correct Usage
Note the following:
!
Warning
This device and its components may only be used for the applications described in the catalog or the
technical description, and only in connection with devices or components from other manufacturers which
have been approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored, set up, and installed
correctly, and operated and maintained as recommended.
Trademarks
SIMATIC, SIMATIC HMI and SIMATIC NET are registered trademarks of SIEMENS AG.
Third parties using for their own purposes any other names in this document which refer to trademarks
might infringe upon the rights of the trademark owners.
Copyright W Siemens AG 2002 All rights reserved
Disclaim of Liability
The reproduction, transmission or use of this document or its
contents is not permitted without express written authority.
Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or
design, are reserved.
We have checked the contents of this manual for agreement
with the hardware and software described. Since deviations
cannot be precluded entirely, we cannot guarantee full
agreement. However, the data in this manual are reviewed
regularly and any necessary corrections included in
subsequent editions. Suggestions for improvement are
welcomed.
Siemens AG
Organization Group Automation and Drives
Division Systems Engineering
Postfach 2355, DĆ90766 Fürth
Index-2Aktiengesellschaft
Siemens
 Siemens AG 2002
Technical data subject to change.
Dokumentation Titel 1Titel 2
EWA 4NEB 780 6023-01
A5E00131465
Preface
Purpose of the Manual
This manual contains all the information you need for commissioning and using the
SIMATIC Box PC 620.
It is intended both for programming and testing/debugging personnel who
commission the device itself and connect it with other units (automation systems,
further programming devices) as well as for service and maintenance personnel
who install expansions or carry out fault/error analyses.
Where is this Manual Valid?
This manual is valid for all supplied variations of the SIMATIC Box PC 620 and
describes the state of delivery as of April 2002.
Certifications, Standards and Approvals
Certifications
The device fulfils the following guidelines and certifications:
EU guideline 73/23/EEC on low voltages
EU guideline 89/336/EEC on electromagnetic compatibility
Underwriters Laboratories (UL) to Standard UL 1950 or UL 508
Canadian Standard Association (CSA) to Standard C22.2 No. 950 or No. 142
Standards and Approvals
The device fulfils the requirements for the CE approval. Approvals for UL and CSA
are available.
Further information on the approvals, certificates, and licenses for your device is
provided in Chapter 1.
Incorporation into the Communications Environment
This manual forms part of the supplied CD “Documentation and Drivers”.
For supplementary instructions on how to handle the software please refer to the
corresponding manuals (for example, Programming with STEP 7 Manual).
SIMATIC Box PC 620 Manual
A5E00131465-01
iii
Preface
Structure of the Manual
In Chapters 1 to 4 the manual contains the most important instructions for starting
up and using the Box PC 620. Chapters 5 to 9 are reference sections you will only
require in special cases.
Important Information
This chapter provides information about safety instructions, certificates, directives
and approvals.
Introduction
Before using your device for the first time you should read Chapter 2 to obtain
more information about the Box PC 620 components and their function.
Setting Up and Operation
The basic commissioning steps can be found in Chapter 3. Furthermore, you will
find instructions there on how to work with memory modules for automation
devices and further ports.
Expansion
Chapter 4 describes how to expand your Box PC 620 (for example, installation of
memory expansions). Please observe the safety instructions.
Configuration
Modifications to the system hardware may make it necessary for you to adapt the
original hardware configuration. Chapter 5 tells how to proceed in this case.
Error/Fault Dignostics
Chapter 6 will tell you how to deal with simple faults that you can diagnose and, in
some cases, eliminate yourself.
Hardware-Informationen
Chapter 7 provides information on the system resources and connecting cables.
Reinstallation of the Software
Chapter 8 shows how to proceed in case you have to reinstall software.
ESD Guidelines
The guidelines for handling electrostatic sensitive devices in Chapter A are of
particular importance for service and maintenance engineers who install
expansions or carry out error analysis with the Box PC 620.
Technical Specifications
Appendix B lists the valid technical specifications for your device. Detailed
information on how your Box PC 620 is equipped can also be found in the BIOS
message (Summary Screen) when your PC is booting up.
iv
SIMATIC Box PC 620 Manual
A5E00131465-01
Preface
Glossary
The glossary explains important terms.
Alphabetical Index
The index will enable you to quickly find passages in the text pertaining to
important keywords.
Conventions
The abbreviation Box PC oder device is also used within this manual for the
product designation SIMATIC Box PC 620.
Further Support
If you have questions related to the use of the products which are not answered in
this manual, please consult your Siemens representative in your local agency.
http://www.ad.siemens.de/partner
Training Center
Siemens offers a number of training courses to familiarize you with the SIMATIC
S7 automation system. Please contact your regional training center or our central
training center in D 90327 Nuremberg, Germany for details:
Telephone:
+49 (911) 895-3200
http://www.sitrain.com/
SIMATIC Documentation on the Internet
You will find the documentation on the internet at:
http://www.ad.siemens.de/support
Use the Knowledge Manager to find the documentation you need quickly. If you
have any questions or suggestions concerning the documentation you can use the
”Documentation” conference in the internet forum.
SIMATIC Box PC 620 Manual
A5E00131465-01
v
Preface
Automation an Drives, Service & Support
Available worldwide, around the clock:
Nuremberg
Johnson City
Singapore
SIMATIC Basic Hotline
Worldwide (Nuremberg)
Technical Support
(Free Contact)
Local time: Mo.–Fr. 7:00 to 17:00
Phone:
+49 (180) 5050 222
Fax:
+49 (180) 5050 223
E-mail:
techsupport@
ad.siemens.de
+1:00
GMT:
Worldwide (Nuremberg)
Technical Support
(charged, only with
SIMATIC Card)
Local time: Mo.–Fr. 0:00 to 24:00
Phone:
+49 (911) 895-7777
Fax:
GMT:
+49 (911) 895-7001
+01:00
Europe / Africa (Nuremberg)
Authorization
America (Johnson City)
Technical Support and
Authorization
Asia / Australia (Singapore)
Local time: Mo.–Fr. 7:00 to 17:00
Local time: Mo.–Fr. 8:00 to 19:00
Local time: Mo.–Fr. 8:30 to 17:30
Phone:
+49 (911) 895-7200
Phone:
+1 423 461-2522
Phone:
Fax:
+49 (911) 895-7201
Fax:
+1 423 461-2289
Fax:
+65 740-7001
E-mail:
authorization@
nbgm.siemens.de
E-mail:
simatic.hotline@
sea.siemens.com
E-mail:
simatic.hotline@
sae.siemens.com.sg
GMT:
+1:00
GMT:
–5:00
GMT:
+8:00
Technical Support and
Authorization
+65 740-7000
German and English are spoken on all the SIMATIC hotlines, French, Italian and Spanish are also spoken on the
authorization hotline.
vi
SIMATIC Box PC 620 Manual
A5E00131465-01
Preface
Service & Support on the Internet
In addition to our documentation, we offer our Know-how online on the internet at:
http://www.ad.siemens.de/support
where you will find the following:
Current Product Information leaflets, FAQs (Frequently Asked Questions),
Downloads, Tips and Tricks.
A newsletter giving you the most up-to-date information on our products.
The Knowledge Manager helps you find the documents you need.
Users and specialists from all over the world share information in the forum.
Your local customer service representative for Automation & Drives in our
customer service representative data bank.
Information on field service, repairs, spare parts and more under ”Services”.
SIMATIC Box PC 620 Manual
A5E00131465-01
vii
Preface
viii
SIMATIC Box PC 620 Manual
A5E00131465-01
Table of contents
1
2
3
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1.1
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1.2
Certificates, Directives and Declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5
1.3
Certification for the USA, Canada and Autralia . . . . . . . . . . . . . . . . . . . . . .
1-7
1.4
Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-9
Welcome to the SIMATIC Box PC 620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2.1
Port Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2.2
Drive Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
2.3
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5
2.4
Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6
2.5
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
2.6
2.6.1
2.6.2
2.6.3
2.6.4
Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disk Drive (Depending on the Device Configuration) . . . . . . . . . . . . . . . . .
LS 240 Drive (Depending on Device Configuration) . . . . . . . . . . . . . . . . . .
Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CD ROM or CD RW/DVD(Combo) Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
2-8
2-8
2-11
2-11
2.7
Backup Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-12
Setting Up and Operating the SIMATIC Box PC 620 . . . . . . . . . . . . . . . . . . . . . . .
3-1
3.1
Unpacking and Checking the Scope of Delivery . . . . . . . . . . . . . . . . . . . . .
3-2
3.2
Installing the SIMATIC Box PC 620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3
3.3
Preparing for Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-10
3.4
Connecting Peripheral Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-12
3.5
Working with PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-17
3.6
Connecting the SIMATIC Box PC 620 to other SIMATIC S5 . . . . . . . . . . .
3-19
3.7
Connecting the SIMATIC Box PC 620 to a SIMATIC S7 Network
(PROFIBUS/MPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-23
3.8
Networking the SIMATIC Box PC 620 with Other Stations on PROFIBUS
3-25
3.9
Ethernet (RJ45 Ethernet Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-26
3.10
Connection under Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-26
SIMATIC Box PC 620 Manual
A5E00131465-01
ix
Table of contents
4
5
6
x
SIMATIC Box PC 620 Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4.1
4.1.1
4.1.2
4.1.3
4.1.4
Opening the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the SIMATIC Box PC 620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Components Visible After Opening the Unit . . . . . . . . . . . . . . . . . . . . . . . . .
The Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
4-2
4-4
4-5
4-6
4.2
Installing Memory Expansion Submodules . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8
4.3
Replacing the Backup Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10
4.4
4.4.1
4.4.2
Installation of Expansion Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation of the Device for Holding Down the modules . .
Removal and Installation of an Expansion Card . . . . . . . . . . . . . . . . . . . . . .
4-12
4-14
4-16
4.5
4.5.1
4.5.2
4.5.3
4.5.4
Removal and Installation of Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation of the Hard Disk Drive . . . . . . . . . . . . . . . . . . . . .
Removal and Installation of a CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation of the Floppy Drive . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation of the LS 240 Drive . . . . . . . . . . . . . . . . . . . . . . . .
4-17
4-17
4-19
4-20
4-21
4.6
Removal and Installation of the Power Supply Unit . . . . . . . . . . . . . . . . . . .
4-22
4.7
Removal and Installation of the Bus Board . . . . . . . . . . . . . . . . . . . . . . . . . .
4-23
4.8
Removal and Installation of the Motherboard . . . . . . . . . . . . . . . . . . . . . . . .
4-24
4.9
Removal and Installation of the Device Fan . . . . . . . . . . . . . . . . . . . . . . . . .
4-25
4.10
Processor Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-26
4.11
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-27
Configuring the SIMATIC Box PC 620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5.1
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
5.1.6
5.1.7
5.1.8
Changing the Device Configuration with BIOS SETUP . . . . . . . . . . . . . . . .
The Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Power Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Boot Sequence Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Version Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default Setup Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2
5-5
5-15
5-22
5-24
5-25
5-27
5-28
5-29
5.2
Configuring the PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-32
Error Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6.1
Problems When Using Modules from Other Manufacturers . . . . . . . . . . . .
6-2
6.2
The Monitor Remains Dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3
6.3
The Screen Display Does not Appear or Drifts . . . . . . . . . . . . . . . . . . . . . . .
6-4
6.4
No Mouse Pointer Appears on the Screen . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4
6.5
The Clock Time and/or the Date in Your PC Is Incorrect . . . . . . . . . . . . . .
6-5
6.6
USB-Device does not function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-5
6.7
An Error Message Appears on the Screen . . . . . . . . . . . . . . . . . . . . . . . . . .
6-6
6.8
Diagnostic Messages (Port 80) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Table of contents
7
8
A
B
Hardware Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1
7.1
Current Requirement of the Components (Maximum Values) . . . . . . . . . .
7-2
7.2
Overview of the Components and Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3
7.3
System Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4
7.4
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
Monitoring functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signals on the Front Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Monitoring/Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog (WD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5
7-5
7-5
7-6
7-7
7-8
7.5
7.5.1
7.5.2
7.5.3
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assignment of the Front Ports on the Motherboard . . . . . . . . . . . . . . . . . . .
Assignment of the Internal Ports on the Motherboard . . . . . . . . . . . . . . . . .
7-9
7-9
7-18
7-23
7.6
7.6.1
7.6.2
7.6.3
Bus Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Design and Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISA Slot Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Slot Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-31
7-31
7-32
7-34
7.7
Power Supply with 85W power output (AC and DC) . . . . . . . . . . . . . . . . . .
7-36
7.8
Power Supply with 105W power output (AC and DC) . . . . . . . . . . . . . . . . .
7-37
7.9
Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-38
Reinstallation of the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1
8.1
8.1.1
8.1.2
8.1.3
Restoring the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating Partitions under Microsoft Windows 98 . . . . . . . . . . . . . . . . . . . . .
Creating Partitions under Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating Partitions under Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2
8-2
8-3
8-4
8.2
8.2.1
8.2.2
8.2.3
Installing the Windows Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Recovery CD for Microsoft Windows 98 . . . . . . . . . . . . . . . .
Installing the Recovery CD for Microsoft Windows NT . . . . . . . . . . . . . . . .
Installing the Recovery CD for Microsoft Windows 2000 . . . . . . . . . . . . . .
8-6
8-6
8-7
8-8
8.3
Installing Drivers and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-11
8.4
Installing and Operating the Burner Software . . . . . . . . . . . . . . . . . . . . . . . .
8-11
Guidelines for handling electrostatic sensitive devices (ESD) . . . . . . . . . . . .
A-1
A.1
What does ESD mean? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
A.2
Electrostatic charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-3
A.3
Basic protective measures against discharge of static electricity . . . . . . .
A-4
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-1
B.1
B-2
Technical Specifications of the SIMATIC Box PC 620 . . . . . . . . . . . . . . . . .
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glossar-1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index-1
SIMATIC Box PC 620 Manual
A5E00131465-01
xi
Table of contents
xii
SIMATIC Box PC 620 Manual
A5E00131465-01
Important Information
1.1
!
1
Safety Instructions
Caution
The safety instructions given on the reverse of the title page of this manual must
be observed. Before expanding your Box PC refer to Chapter 4 and read the
relevant safety instructions.
This device corresponds to the relevant safety measures according to IEC, EN,
VDE, UL, and CSA. If you have questions about the permissibility of the installation
in the designated environment, please contact our service representative.
Installation
Condensation can occur if the device is transported from a cold environment into
the operating area. The device must be dry prior to startup. You must allow for an
acclimatization time of at least twelve hours.
Please observe the notes on ambient conditions in Appendix B Technical
Specifications and the installation notes in Section 3.2 of this manual when
installing and operating the device. The device is to be installed so that there is no
danger of it falling or of causing damage to itself or others.
Be sure the fan ventilation slots are open so that a sufficient amount of air can be
drawn in to cool the housing interior.
!
Warning
Adhere to the permissible mounting positions when mounting the systems (see
chapter 3.2).
If the systems are installed in a non-permissible fitting position, the approvals
pursuant to UL 1950, UL 508 and EN60950 are no longer valid!
SIMATIC Box PC 620 Manual
A5E00131465-01
1-1
Important Information
Power Connection
Install the cables so that no one can step on them or trip over them. When you
connect the device, adhere to the relevant instructions in Chapter 2 of this manual.
Do not connect or disconnect power supply cables and data transmission lines
during thunderstorms.
In emergency situations (for example, damaged housing, damaged operator
elements, a damaged power supply cable, ingress of liquids or foreign particles),
switch off the device. Disconnect the power plug and inform the responsible
service personnel.
When plugging in/unplugging peripheral connections (keyboard, mouse, printer
etc.) the Box PC must be switched off (not for PC-Card and USB-devices). In the
case of non-observance, this can lead to damage to the PC.
Notes for Devices with AC Power Supply
The device is intended for service in grounded electricity supply systems
(TN systems to VDE 0100, part 300, or IEC 364-3).
Service in non-grounded or impedance-grounded supply systems (IT systems) is
not intended.
The power cord should meet the respective local safety requirements.
Check whether the device’s set supply voltage is the same as the local supply
voltage.
This device is equipped with a safety-tested power supply cable. You may connect
this device only to a grounding outlet with a grounding contact.
Make certain that the socket outlet on the device or the grounding contact for the
building wiring system is freely accessible and as near to the device as possible.
The mains switch does not separate the device from the power system. To
establish a complete power separation, you must disconnect the power plug (inlet
connector on the back of the device). This location must be accessible. A central
isolating switch must be present for cabinet mounting.
Notes for Devices with DC Power Supply
The device with DC power supply (24V DC) is an open device (right side of the
device), therefore the mounting must meet the requirements of fire protection
enclosures.
!
Warnung
Only connect the device to 24V DC power supply systems which meet the requirements of a
safe extra-low voltage (SELV).
The cable cross section has to be large enough that the Box PC will not be damaged by the
cables when there is a short circuit.
1-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Important Information
Country-Specific Information
For the United States and Canada:
In the United States and Canada USA, a CSA or UL-listed power supply cable
must be used.
The male plug is a 5-15 style.
For operation with 120 V:
Use a UL Listed, CSA Labelles Cord Set, consisting of a min. 18 AWG. Type SVT
or STJ three conductor flexible cord, max. 4.5 m (15 feet) in length and a parallel
blade grounding type attachment plug rated 15 A, min 125 V.
For operation with 240 V:
Use a UL Listed, CSA Labelled Cord Set, consisting od a min. 18 AWG. Type SVT
or SJT three conductor flexible cord, max. 4.5 m (15 feet) in length and a tandem
blade grounding type attachment plug, rated 15 A, 250 V.
For operation with 230 V (outside of USA and Canada)
Use a Cord Set consisting of a min 18 AWG cord and grounding type attachment
plug rated 15 A, 250 V. The cord set should have the approviate safety approvals
for the country in which the equipment will be installed and marked.
Repairs
Only authorized personnel are permitted to repair the Box PC.
!
Warning
Unauthorized opening and improper repairs on the device can result in significant
danger to the user.
Before you open the device, first switch it off and then disconnect the power plug.
Install only system expansion devices provided for this computer. If you install
other expansion devices, you can damage the system or violate the safety
requirements and regulations for radio interference suppression. Contact your
technical support team or where you purchased your PC to find out which system
expansion devices may safely be installed.
If you install or exchange system expansions and damage your Box PC, the
warranty becomes void.
The power supply may only be dismantled or exchanged by authorized technical
personnel.
SIMATIC Box PC 620 Manual
A5E00131465-01
1-3
Important Information
Battery
There is a battery in this device on the motherboard. Batteries may only be
exchanged by technical personnel.
Observe the local regulations on disposal of special waste when disposing of dead
batteries.
!
Caution
There is the danger of an explosion, if the battery is not exchanged as directed.
Replace only with the same type or an equivalent type recommended by the
manufacturer. Dispose of used batteries in accordance with the legal instructions
of your area.
Notes on Inserting and Removing Modules (ESG Guidelines)
Modules containing electrostatically sensitive devices (ESDs) can be identified by
the following label:
Please observe and carefully follow the guidelines mentioned below when handling
modules equipped with electrostatically sensitive devices:
1-4
Always discharge your body before handling modules equipped with ESDs (for
example, by touching a grounded object).
Devices and tools must be free of static electricity.
Always pull the power plug and disconnect the battery before connecting or
disconnecting modules (containing ESDs).
Touch modules fitted with ESDs by their edges only.
Never touch wiring posts or printed conductors on modules containg ESDs.
SIMATIC Box PC 620 Manual
A5E00131465-01
Important Information
1.2
Certificates, Directives and Declarations
Notes on the CE Symbol
The following applies to the SIMATIC product described in this manual:
EMC Directive
Devices with a power supply performance of 85W are in accordance with the
EU Directive 89/336/EEC “Electromagnetic Compatibility.” In accordance with the
CE label for this product, the following areas of application are relevant:
Field of Application
Requirement For
Emitted Interference
Noise Immunity
Domestic, business and commercial
areas, as well as small businesses
EN 50081-1: 1992
EN 50082-1: 1992
Industry
EN 50081-2: 1993
EN 50082-2: 1995
The devices with AC power supply meet the norms of the the EN 61000-3-2:1995
(harmonic currents) and EN 61000-3-3:1995 (voltage fluctuation and flicker).
The devices with power supply performance of 105W are in accordance with the
EU Directive 89/336/EEC “Electromagnetic Compatibility.” In accordance with the
CE label for this product, the following area of application is relevant:
Application
Requirements
Emitted Interference
Industrial area
EN 50081-2: 1993
Immunity
EN 50082-2: 1995
The devices with AC power supply meet the norms of the the EN 61000-3-2:1995
(harmonic currents) and EN 61000-3-3:1995 (voltage fluctuation and flicker).
Caution
This is a class A electronic device. This device may cause interference in
residential areas. In this case the user may be asked to take the necessary
precautions.
Low Voltage Directive
The devices with AC power supply complies with the requirements of the EU
Directive 73/23/EEC “Low-Voltage Directive.” Conformance with this standard has
been verified according to EN 60950.
SIMATIC Box PC 620 Manual
A5E00131465-01
1-5
Important Information
Declaration of Conformity
The EC declarations of conformity and the documentation relating to this are
available to the authorities concerned, according to the above EC directive, from:
Siemens AG
Group Automation & Drives
A&D AS RD 4
Postfach 1963
D-92209 Amberg
Tel.: +49 (9621) 80-3283
Fax: +49 (9621) 80-3278
Observing the Setup Guidelines
The setup guidelines and safety instructions given in this electronic manual must
be observed on startup and during operation.
Connecting Peripherals
The requirements regarding noise immunity (EN50082-2:1995) are met when you
connect a peripheral suitable for an industrial environment. Peripheral devices are
only be connected via shielded cables.
ISO 9001 Certificate
The quality assurance system for the whole product process (development,
production, and marketing) fulfills the requirements of ISO 9001 (corresponds to
EN29001: 1987).
This has been certified by the German society for the certification of quality
management systems (DQS).
EQĆNet certificate no.: 1323Ć01
Software License Agreement
The Box PC is shipped with the software already installed. Please observe the relevant license agreements.
1-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Important Information
1.3
Certification for the USA, Canada and Autralia
Security
One of the following markings on a device is indicative of the corresponding
approval:
Underwriters Laboratories (UL) to the UL 1950 Standard (I.T.E)
or to the UL508 (IND.CONT.EQ)
C
Underwriters Laboratories (UL) to the Canadian Standard C22.2 No. 950
(I.T.E) or to the C22.2 No. 142 (IND.CONT.EQ)
C
Underwriters Laboratories (UL) to Standard UL 1950, Report E11 5352 and to
the Canadian Standard C 22.2 No.950 (I.T.E)
or to the UL508 and C22.2 No. 142 (IND.CONT.EQ)
US
UL-Recognition-Mark
Canadian Standard Association (CSA) to standard C22.2. No. 950
(LR 81690) or to C22.2 No. 142 (LR 63533)
NRTL
Canadian Standard Association (CSA) to the American Standard UL 1950
(LR 81690) or to the UL 508 (LR 63533)
SIMATIC Box PC 620 Manual
A5E00131465-01
1-7
Important Information
EMC
USA
Federal Communications Commission
Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Shielded Cables
Shielded cables must be used with this equipment to maintain compliance with FCC regulations.
Modifications
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Conditions of Operations
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Canada
(for devices with power supply 105W)
Canadian Notice
This Class A digital apparatus complies with Canadian ICES-003.
Avis Canadien
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
(for devices with power supply 85W)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Avis Canadien
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Australia
This product meets the requirements of the AS/NZS 3548 Norm.
1-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Important Information
1.4
Transport
Transporting
Despite the fact that the Box PC is of rugged design, its internal components are
sensitive to severe vibrations or shock. You must therefore protect the PC from
severe mechanical stress when transporting it.
Use the original packing material if you have to ship the Box PC from one
location to another.
Caution
Risk of damage!
When transporting the PC in cold weather, when it may be submitted to extreme
variations in temperature, make sure that there is no moisture (condensation) on
or in the PC.
The PC must be allowed to reach room temperature slowly before you switch it on.
If condensation has formed, you should wait approximately 12 hours before
switching on the PC.
SIMATIC Box PC 620 Manual
A5E00131465-01
1-9
Important Information
1-10
SIMATIC Box PC 620 Manual
A5E00131465-01
Welcome to the SIMATIC Box PC 620
2
Overview of Chapter
In chapter
you will find
on page
2.1
Port Side View
2-2
2.2
Drive Side View
2-4
2.3
Side View
2-5
2.4
Bottom View
2-6
2.5
Ports
2-7
2.6
Drives
2-8
2.7
Backup Battery
SIMATIC Box PC 620 Manual
A5E00131465-01
2-12
2-1
Welcome to the SIMATIC Box PC 620
2.1
Port Side View
1
2
13
12
34
11
5
10
9
8
6
7
Figure 2-1 Ports
1
Mouse
PS/2 socket for connecting a PS/2 mouse.
2
COM1 V.24 /MODEM /AG
The COM 1 (TTY) port is used to connect, for example, S5 automation units (AG).
The supplied adapter can be used to convert the port into a 25-pole standard V.24
port for connecting serial port devices such as modem, mouse or printer. The line
current (TTY) interface is an optional product feature.
3
COM2
You can use the serial port 2 (V.24) to connect devices with a serial port such as
modem, mouse or printer.
4
AC/DC Power Supply Connector
Appliance socket for AC power supply or screw terminal for DC power supply.
5
PCI Slots
Internal slots for expansion modules.
6
PCI/ISA Slots
Internal slots for expansion modules.
7
PC Card
Connection for PC Cards type I/II/III
2-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Welcome to the SIMATIC Box PC 620
8
Ethernet
RJ 45-Ethernet connector. Ethernet is a local network with a bus structure for data
communication with a data transfer rate of 10 or 100 megabit per second (Mbps).
9
PROFIBUS/MPI (optional)
You can connect the Box PC to an S7 automation system or to a PROFIBUS
network via the PROFIBUS/MPI port with galvanic isolation. This interface is an
optional product feature.
10 USB
Universal Serial Bus connector. You can use the USB port to connect external devices, for example, CD drives, printers, modems as well as mouse and keyboard.
Older operating systems do not support this port.
11 VGA
You can connect an external VGA monitor to this connector.
12 LPT1
The parallel port connection for devices with parallel port (for example, printer).
13 Keyboard
Connection for a PS/2 keyboard.
Caution
Ensure that you use shielded cables and metal plugs to connect the peripheral
units; if this is not done, the approval for operation will be invalid! Screw down the
plugs of the interface cables to the PC housing by means of a screwdriver. You
thereby improve the electrical shielding.
If expansion modules have been inserted in the PC, there are additional ports.
Please refer to the description of the respective module for their purpose.
SIMATIC Box PC 620 Manual
A5E00131465-01
2-3
Welcome to the SIMATIC Box PC 620
2.2
Drive Side View
1
2
5
3
4
Figure 2-2 Drive Side View
1
Device Fan
Here are openings for device ventilation.
Caution
The air venting slots for outgoing air must not be obstructed. Otherwise, there is a
risk of overheating.
2
Type Label
You can find the order number and the serial number of your device on the type
label.
3
Floppy disk drive (LS240 as an alternative)
Depending on the device configuration a standard floppy disk drive (1.44 Mbytes)
or an LS240 Super disk drive is installed. Floppy disks up to 1.44 Mbytes as well
as Super disks up to 240 Mbytes can be used in LS240 drives.
4
Front Ports
The front ports are located behind the cover below the floppy disk drive. They are
used for connection of the following front elements:
I/O port for the connection of front components
LVDS display port
5
Reset Button
The reset button can be actuated with a thin pen (e.g. an opened up paper clip). If
you actuate, the button, a hardware reset is triggered. The PC restarts. Data loss
is possible with a hardware reset.
2-4
SIMATIC Box PC 620 Manual
A5E00131465-01
Welcome to the SIMATIC Box PC 620
2.3
Bottom View
1
Figure 2-3
1
Bottom View
Equipotential Grounding
The connection with the equipotential grounding on the system housing to the
central earth terminal of the cabinet or the unit into which the computer is fitted,
ensures that faults arising from external power supply cables, signalling cables or
cables to peripheral units are diverted.
SIMATIC Box PC 620 Manual
A5E00131465-01
2-5
Welcome to the SIMATIC Box PC 620
2.4
Side View
1
2
3
Figure 2-4 Side View
1
Mounting possibilities for the WinAC Backup Battery
You can mount the SIMATIC WinAC CPU41x-2PCI backup battery here. Use the
battery holder without a slot plate supplied with the WinAC module to do this.
2
Input Data of Power Supply Unit
To distinguish between both performances of the power supply unit, the power supply unit with a 105W performance been marked with Pmax=105W.
3
Certificate of Authenticity with Product Key
You need the Microsoft Windows “Product Key” on the “Certificate of Authenticity”
if you reinstall software.
2-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Welcome to the SIMATIC Box PC 620
2.5
Ports
Front Ports
The front ports are located behind the cover below the floppy disk drive. They are
used for connection of the following front elements:
I/O port for the connection of front components
LVDS display port
CMOS display port
The front ports can be accessed as follows:
1. Undo the plastic rivet on the cover below the floppy disk drive with a flat
screwdriver.
2. Pull the cover out of the guide. The front ports are now accessible.
The CMOS display port is only accessible after removal of the floppy disk drive.
Notice
Keep the cover and the plastic rivet for reuse.
VGA Port
Please read the following note referring to the operation of a flat display and an
external monitor:
Notice
The default setting of the display provides the simultaneous operation of a flat display
and an external monitor. If no front display element is connected, the display is
effected on the external monitor with a resolution of 640 x 480 pixels. Modes with a
lower resolution and text modes are expanded to this format.
To optimize the screen display for an external monitor, select ”Hardware Options”
under Setup in the main menu and set ”CRT/LCD selection: CRT enabled”. A
resolution of 1024 x 768 pixels with a higher refresh rate is then possible.
SIMATIC Box PC 620 Manual
A5E00131465-01
2-7
Welcome to the SIMATIC Box PC 620
2.6
Drives
The Box PC is equipped as standard with a 3.5” disk drive or an LS240 drive and a
3.5” hard disk drive.
2.6.1
Disk Drive (Depending on the Device Configuration)
You can store programs and data on diskettes with the disk drive and load them
from diskettes into the Box PC.
Types of Diskette
You can use following diskettes:
double sided double
density diskette
!
double sided high density
diskette
LS240-Superdisks
3,5 inch
3,5 inch
3,5 inch
720 Kbytes
1,44 Mbytes (135 TPI)
120 Mbytes
Caution
Risk of loss of data!
When the green access LED of the floppy disk drive is lit, the ejector may not be
actuated.
2.6.2
LS 240 Drive (Depending on Device Configuration)
The Box PC can be equipped with an LS 240 drive as an alternative to a floppy
disk drive.
Larger volumes of data can be stored on LS 240 data carriers than on a
1.44 MB floppy disk drive. The LS 240 has the following features:
– it is compatible with a 1.44 MB floppy disk drive, i.e. 1.44 MB or 120 MB
disks can also be processed.
– an LS 240 data carrier has a maximum data volume of 240 Mbytes.
– the LS 240 drive is connected via an ATAPI (IDE) port.
2-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Welcome to the SIMATIC Box PC 620
Handling Disks with the LS 240 Drive
Depending on the fitting position, the disks are inserted into the disk drive as
illustrated below:
Access hole for emergency ejection (only LS240)
Ejector
Access LED
Ejector
Access LED
Figure 2-5 Handling Disks
!
Caution
Risk of loss of data!
When the green access LED of the LS 240 drive is lit, the ejector may not be
actuated.
LS 240 drives are very sensitive to shocks of a non-permissible level. Shocks
during operation can lead to damage to the drive or the data carrier. You can find
the permissible values in the technical data in Section B.
Information on the LS240 Disk Drive
Restrictions
P-Tools under STEP 5
Data cannot be edited in PCP/M format on the LS240 drive using P Tools under
STEP 5.
Notice
When you use the P Tools (for editing PCP/M files) supplied with STEP 5,
remember that these are not fully supported by the Windows 98 and
Windows 2000 operating systems nor by LS240 diskette drives. If you use the
P Tools, we recommend that you use MS-DOS, Windows 3.x or Windows 95 and
standard 1.44 Mbyte floppies.
SIMATIC Box PC 620 Manual
A5E00131465-01
2-9
Welcome to the SIMATIC Box PC 620
Authorization with Authors W V2.x
To authorize STEP 7 and other SIMATIC components you must use AuthorsW.
Start this program on the PG via the taskbar under Start > Simatic > AuthorsW.
Usage Notes for LS240 Superdisks
LS240 drives are suitable for floppy disks up to 1.44 Mbytes as well as Superdisks
up to 120 Mbytes.
Track density for Superdisks is10 mm compared with the 120 mm of conventional
disks.
The LS240 recognizes when a Superdisk is in the drive and switches to the higher
capacity. With conventional disks, a capacity of 1.44 Mbytes or 720 Kbytes can be
reached.
Due to their higher storage capacity, Superdisks are more sensitive to dirt, temperature and shock than conventional disks.
Notice
In order to achieve a reliable operation and high data security, please note the
following during use:
Store and transport the Superdisk in the protective cassette included to keep
dust and dirt from the disk.
Remove Superdisk from the drive when it is not being read or written to keep
dirt particles away from the disk. Do not expose the disk unnecessarily to high
operating temperatures.
Notice
If possible avoid vibration of the unit, when using Superdisks. Superdisks are more
sensitive to vibration as a result of their high track density.
Emergency Removal:
When the unit is switched off, the disk can be forced out by using a pin
(for example, a bent paper clip).
2-10
SIMATIC Box PC 620 Manual
A5E00131465-01
Welcome to the SIMATIC Box PC 620
2.6.3
Hard Disk Drive
The hard disk drive is used for the storage of large quantities of data. it is fitted in a
mounting which is easily exchangeable and damped against vibration.
!
2.6.4
Caution
Risk of loss of data and damage to the drive!
Drives are sensitive to vibrations and shock. Any vibrations occurring during
operation can lead to the loss of data or damage to the drive.
If you intend transporting the unit, switch it off, and wait until the drive has come to
rest (about 20 seconds) before you move it.
CD ROM or CD RW/DVD(Combo) Drive
Depending on the device equipment, a CD-ROM or a CD-RW/DVD drive is fitted in
the SIMATIC Box PC 620. The fitting depth of the PC is increased by 20mm as a
result.
Operation
When the open/close button is pressed, the CD/DVD tray is travelled out with a
slight delay. Insert the CD/DVD with the labelling facing forwards into the tray. The
CD/DVD tray is retracted automatically, when the tray is pressed briefly or the the
Open/Close button is pressed.
By briefly pressing the eject button, the drawer springs out slightly. You can
remove the CD/DVD.
Emergency removal
When the device ist switched off, the disk can be forced out by using a pin (for
example, a opened up paper clip).
Notice
After the drawer has been closed, the CD/DVD is tested and the access display
light on the drive starts to flash:
– If the access LED flashes continually, the CD/DVD is faulty but can still be
read,
– If the access LED flashes several times and then remains lit, the CD/DVD
you have inserted is defective and cannot be read.
– normally the access LED is lit when reading the CD/DVD.
Caution
CD-ROM or CD-RW/DVD drives are sensitive to vibrations and shock. Any vibrations occuring during operation can lead to damage to the drive or CD/DVD.
SIMATIC Box PC 620 Manual
A5E00131465-01
2-11
Welcome to the SIMATIC Box PC 620
Additional Software
To be attain the full functionality of the CD RW/DVD ROM drive, additional software (DVD player or burner software) is necessary. You can find it on the CD included in the delivery of the device. To install the software place the CD in the drive
and follow the instructions on the screen.
2.7
Backup Battery
A backup battery (3.6 V lithium battery) powers the hardware clock even after the
programming device is switched off.
There is a battery on the motherboard in this device. Batteries may only be
exchanged by technical personnel. Note the information in the documentation of
the CPU module! Observe the local regulations on the disposal of special waste
when disposing of dead batteries.
!
!
2-12
Caution
There is the danger of an explosion if the battery is not exchanged as directed.
Replace only with the same type or an equivalent type recommended by the
manufacturer. Dispose of used batteries in accordance with the manufacturer’s
instructions.
Warning
Risk of severe personal injury or property damage, danger of release of harmful
substances.
There may be a danger of explosion if the battery is not handled properly.
Incorrect disposal of used batteries can cause the release of harmful substances.
Do not throw a new or discharged lithium battery into an open fire, do not solder
onto the cell container. Do not recharge the battery, do not open the battery by
force.
The correct lithium battery is available from Siemens (order no.: W79084-E1003-B1).
Return used batteries to the manufacturer/recycler or dispose of them according to
local regulations.
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the
SIMATIC Box PC 620
3
Chapter Overview
In chapter
you will find
on page
3.1
Unpacking and Checking the Scope of Delivery
3-2
3.2
Installing the SIMATIC Box PC 620
3-3
3.3
Preparing for Operation
3-10
3.4
Connecting Peripheral Devices
3-12
3.5
Working with PC Cards
3-17
3.6
Connecting the SIMATIC Box PC 620 to other SIMATIC S5
3-19
3.7
Connecting the SIMATIC Box PC 620 to a SIMATIC S7 Network
(PROFIBUS/MPI)
3-23
3.8
Networking the SIMATIC Box PC 620 with Other Stations on
PROFIBUS
3-25
3.9
Ethernet (RJ45 Ethernet Interface)
3-26
3.10
Connection under Windows
3-26
SIMATIC Box PC 620 Manual
A5E00131465-01
3-1
Setting Up and Operating the SIMATIC Box PC 620
3.1
Unpacking and Checking the Scope of Delivery
Unpacking the SIMATIC Box PC 620
Unpack your Box PC as follows:
1. Remove the Box PC from the packaging.
2. Do not throw the original packing away. Keep it in case you have to transport
the unit again sometime in the future.
3. Please keep the documentation in a safe place. It is required during the initial
start up and is part of the device.
4. Check the packing and its contents for any shipping or transport damage.
5. Check with the packing list to make sure no components are missing. Also
check the accessory parts, which you can order separately.
6. Please inform your local dealer of any shipping or transport damages and of
outstanding items indicated on the packing list.
Recording the Serial Number and the Ethernet address
7. Enter the serial number and the Ethernet address of your PC in the table
below. You can find the serial number on the type label attached to the rear of
the device. The Ethernet address can be found in the BIOS setup settings in
the main menu under the ’Hardware Options’ function.
The device can precisely be identified with the help of these numbers in case of
repairs or theft.
Enter the Microsoft Windows “Product Key” from the “Certificate of
Authenticity”
8. Enter the Microsoft Windows “Product Key” from the “Certificate of Authenticity”
(COA) in the table. You will find the “Product Key” on the device on the power
supply unit covering. You need the Windows “Product Key” if you want to
reinstall the operating system.
Serial number
SVP..
Order-No.
6ES...
Microsoft Windows Product Key
Ethernet Address
3-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
3.2
Installing the SIMATIC Box PC 620
The Box PC 620 can be operated in several fitting positions. It is particularly
suitable for fitting in consoles, switch boards and control panels.
The Box PC 620 with AC power supply meets the requirements for a fire
enclosure to EN60950. it can therefore be fitted without an additional fire
enclosure.
The Box PC 620 with DC power supply is an open device (right device side); therefore the mounting must meet the requirements of a fire enclosure.
Please note the following points when installing the PC:
!
Avoid extreme ambient conditions as far as possible. Protect your PC from
dust, moisture, and heat.
Keep the PC out of direct sunlight.
Mount the PC as safely as possible to prevent any danger (for example, by
falling over).
The clearance around the housing must be at least 100 mm at the front and
rear, so that the PC is sufficiently ventilated.
Make certain that the ventilation slots for the housing are not covered.
Observe the permissible fitting positions without fail when installing the
systems.
Warnung
If the systems are installed in a non-permissible fitting position, the approvals
pursuant to UL 1950, UL 508 and EN 60950 are no longer valid!
SIMATIC Box PC 620 Manual
A5E00131465-01
3-3
Setting Up and Operating the SIMATIC Box PC 620
Depending on the configuration of the device, two mounting brackets are included
in the scope of delivery. You can attach these to the housing with 6 screws (M3x6).
M4 thread, max. depth of engagement 5 mm
M3 thread, max. depth of engagement 5 mm
Equipotential grounding connection
Figure 3-1 Screw Connection Points for Mounting Brackets (Cover Side Downwards)
Instructions for wall and ceiling mounting
To install the Box PC in a concrete wall or ceiling proceed as follows:
1. Fix the mounting brackets at the housing of the PC.
2. Drill four holes of 8 mm diameter and 60 mm depth into the wall or ceiling. You
will find the required dimension drawings on the following pages.
3. Insert the concrete plugs (8 mm diameter and 50 mm long) into the drill holes.
4. Fix the PC with four screws (4 mm diameter and 50 mm long).
In a plasterboard wall or ceiling (min. 13 mm thick), drill holes of 14 mm diameter
and fasten the PC with four anchors (4 mm diameter and 50 mm long).
In a metal sheet wall or eiling (min. 2 mm thick), drill holes of 5 mm diameter and
fasten the PC with four screws (4 mm diameter and min. 15 mm long).
!
3-4
Warnung
The installer must verify that the wall or ceiling can support four times the full load
of the Box PC (with mounting brackets and Add-On-Cards).
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
297.2
266
5
301
286
80.1
26
232
11.2
Figure 3-2 Dimension Drawings for Fitting in Control Panel with Installation Angle (Device without CD ROM
Drive)
SIMATIC Box PC 620 Manual
A5E00131465-01
3-5
Setting Up and Operating the SIMATIC Box PC 620
99.1
286
301
297.2
Figure 3-3 Dimension Drawings for Fitting in Control Panel with Installation Angle (Device with CD ROM
Drive)
3-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
297.2
267
80.1
11.2
Figure 3-4 Dimension Drawings for Fitting in Control Panel without Installation Angle
SIMATIC Box PC 620 Manual
A5E00131465-01
3-7
Setting Up and Operating the SIMATIC Box PC 620
Permissible Fitting Positions of the PC to UL1950/EN60950/CSA22.2 No. 950
An inclined position of ± 20 is allowed in each of the permissible fitting positions.
Position 1 (Preferred Position)
Position 3 (Desktop) *)
Position 2 *)
Position 4 (Ceiling) **)
*) . not permissible for installed LS240 Drive
**) not permissible for installed CD ROM, CD RW/DVD Drive
3-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
Additional Permissible Fitting Positions of the PC to UL508/CSA 22.2 No. 142
An inclined position of $15 is allowed in each of the permissible fitting positions.
An external fire protection housing is not necessary.
Position 5
(Fan Side Down)
***)
Position 6
(Port Side Down)
***)
***) not permissible for installed Floppy Disk, CD ROM, CD RW/DVD or LS240 Drive
Caution
The fitting position with the fan side down is only permitted with additional
precautions because warmed air is drawn down against the convection current,
possibly causing a build-up of heat.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-9
Setting Up and Operating the SIMATIC Box PC 620
3.3
Preparing for Operation
Connection to the Power Supply Unit
Connection to power supply
Inlet connector for nonheating appliances
Figure 3-5 Connection to Power Supply (Inlet Connector for Non-Heating Appliances)
!
Caution
The Box PC is equipped with a safety-tested mains cable and may only be connected to a grounded grounding outlet.
Make sure that the socket on the device or the grounding outlet of the building
installation is easily accessible and as near as possible to the device.
The Box PC has no mains switch. The mains plug must be pulled out for complete
mains separation. This point must be easily accessible.
If the PC is installed in a cabinet, there must be a central mains disconnector.
The AC power supply unit of the Box PC 620 is designed for 120/230/240V systems. The power supply unit has a long-range input. It is not necessary to adjust
the voltage span.
The DC-power supply unit of the Box PC 620 is designed for 24V systems.
Optionally, one of these power supplies is installed.
3-10
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
Equipotential Measures
Low-impedance ground connections ensure that faults arising from external power
supply cables, signalling cables or cables to peripheral units are diverted.
Therefore connect the equipotential grounding connection on the system housing
to the central earth terminal of the cabinet or the unit, into which the computer is
fitted, in such a way that it has low impedance (large surface area, large contacts).
The minimum cross section should not be less than 5 mm2.
The connection is on the side of the device and is identified by the symbol:
Connecting and Switching on the SIMATIC Box PC 620
Before you connect the Box PC to the mains, the keyboard, mouse and display or
monitor must be connected.
1. Insert the connector cable of these peripheral units into the corresponding
sockets on the port side of the Box PC (see Section 3.4.).
2. Connect the device to the mains.
3. The device is now ready for power supply operation and is now in service.
Switching off the SIMATIC Box PC 620
Before switching off the Box PC 620, you have to shut down the operating system
to avoid loss of data. The Box PC has no mains switch and is switched off after
only disconnection from the mains.
Notice
If you are working with Windows, you always have to use Start > Shut Down for
switching off.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-11
Setting Up and Operating the SIMATIC Box PC 620
3.4
Connecting Peripheral Devices
Notice
When connecting peripheral units, ensure that the components have industrial
capability.
Connecting the Printer to the Parallel Port
Proceed as follows to connect your printer:
1. Disconnect the Box PC and switch off the printer.
2. Plug the printer cable into the LPT1 parallel port.
3. Connect the printer cable to the printer.
4. Screw the connector tight at the interface port.
COM 1
socket (parallel)
COM 2
port (serial)
LPT 1
socket (parallel)
Figure 3-6 Position of the Printer Ports
!
Caution
Risk of damage to the unit!
Switch the unit off before connecting the parallel printer to the LPT 1 port (the
printer should also be switched off).
Make sure that you use the correct port. If you use the wrong port or wrong
connecting cables, the port may be damaged.
Before plugging in the cables, the electrostatic charge of your body, the unit, and
the cables must be equalized. To do this, touch the mounting plate for the ports on
the left-hand side of the unit.
Only use original connecting cables.
3-12
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
Connecting the Printer to the Serial Port
You can also connect your printer to the SIMATIC Box PC using a serial COM port.
You will find information on how to adapt and set your interface and which connecting cable you require in the description of your printer.
Connecting Monitors
You connect external multisynchronous monitors using the standard
VGA connector on the left-hand panel side of the unit. We recommend that you
use a Siemens monitor.
You must switch the Box PC off before connecting the monitor cable. You will find
further information about the connector pinout in Chapter 7.
VGA-Socket
Figure 3-7 Connecting the Monitor
Proceed as follows to connect your monitor:
1. Disconnect the Box PC and switch off the monitor.
2. Insert the monitor lead in the VGA socket.
3. Screw down the plug.
4. Connect the monitor cable to the monitor.
5. Connect the PC to the power supply and switch on the monitor.
6. Make the necessary changes in the SETUP program
(Menu > Main > Hardware Options “CRT enabled”, “LCD enabled”
“SIMULTAN”)”.
!
Caution
Danger of damaging the monitor!
If you want to set higher clock frequencies and resolutions, first make sure that the
monitor you are using is suitable for a higher clock frequency and resolution.
If the clock frequency is too high, this can cause damage to the monitor.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-13
Setting Up and Operating the SIMATIC Box PC 620
Using a Mouse
You can connect both a PS/2-USB and a serial mouse to the Box PC.
Connecting a PS/2 Mouse
You can connect an external PS/2 mouse or another external pointing device to an
additional PS/2-compatible mouse connector.
Port for PS/2 mouse
(socket)
COM 2 Port for serial mouse
(connector)
USB connection for
USB mouse (socket)
Figure 3-8 Connecting the Mouse
To connect the mouse, proceed as follows:
1. Disconnect the PC from the power supply.
2. Plug the cable of the PS/2 mouse or another external pointing device into the
mouse connector.
3. Connect the PC to the power supply.
Connecting a Serial Mouse
You can connect a serial mouse to the COM2 serial port. To operate a serial
mouse, the appropriate mouse driver must be initialized and assigned parameters.
You will find the information you need to do this in the description of your mouse or
in the description of the operating system.
1. Disconnect the PC from the power supply.
2. Plug the serial mouse into the mouse connector labeled COM2.
3. Secure the connector with the screws.
4. Connect the PC to the power supply.
You can find out how to connect a USB mouse in “Connecting USB devices”.
3-14
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
Connecting a PS/2 Keyboard
A PS/2 keyboard of your choice can be connected to the Box PC.
PS/2 keyboard connection
Figure 3-9 Connecting a PS/2 Keyboard
To connect the keyboard, proceed as follows:
1. Disconnect the Box PC from the power supply.
2. Insert the plug of the PS/2 keyboard.
3. Connect the Box PC to the power supply.
Note
It is recommended that a keyboard with straight keyboard connector is used, so
that the connector does not obscure adjacent ports.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-15
Setting Up and Operating the SIMATIC Box PC 620
Connecting Devices to an USB Interface
You can connect single or multiple USB devices (mouse, keyboard or printer) to
the USB interfaces.
1. Plug the USB device cable into one of the USB interfaces.
The Plug and Play operating system recognizes the device. Any drivers are
requested by the operating system, if necessary.
If you wish to connect more than two USB devices you must use a HUB. Both
interfaces can be used as high-current source.
USB connectors
Figure 3-10 USB connection
Notice
Operating systems which do not support Plug and Play (e.g. Windows NT 4.0), do
not generally allow the operation of USB devices.
Devices that do not have a USB plug (for example, printers) can be connected to
the USB interface via adapter.
3-16
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
3.5
Working with PC Cards
PC Cards
The PC card interface supports Cardbus-Cards (32 Bit) and PCMCIA-Cards
(16 Bit). The Box PC has one PC card port. You can plug communication modules for MODEM, FAX-MODEM, ISDN, Token Ring, ETHERNET, memory expansion and SCSI interface modules in credit-card format into these ports.
PC card interface, type I/II/III
Figure 3-11 PC Card Interface
The following is to be observed when working with cardbus/PC cards:
1. Open the port cover on the left-hand side of the device by undoing the plastic
rivet with a flat screwdriver.
2. Pull the cover out of the guide.
3. Insert the desired PCMCIA card or cardbus card.
!
Caution
Before inserting PC-Cards please make sure that the PC-Card Ejector is
completely pressed otherwise the cards e.g. Flash Memory Cards could get stuck
in the slot. The PC-Cards cannot be inserted correctly.
Always insert the PC card with the label toward the rear of the programming
device.
Do not remove the PC card while data transfer is in progress (risk of data loss and
system crash).
!
Caution
Before plugging in or taking out Cardbus/PC cards, you must discharge the
electrostatic of your body by briefly touching grounded object (ESD guidelines,
Section A.1).
Otherwise faults can occur.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-17
Setting Up and Operating the SIMATIC Box PC 620
Note
Peak currents of 650 mA at 5 V based on 3 s are permitted!
Examples of PCMCIA cards connected to PC card interface for
Hard Disk
330 mA read/write
(Maxtor MXL-131-III) . . . . . 640 mA spin up 2 s
. . . . . . . . . . . . . . . . . . . . . . . . 110 mA idle
Fax/modem . . . . . . . . . . . . . 60 mA idle
(Dr. Neuhaus) . . . . . . . . . . . 140 mA transfer
Ethernet
(XIRCOM) . . . . . . . . . . . . . . 150 mA
Installing PC Cards
Note the following when installing these cards:
Note
Depending on the configuration of the Box PC, there may not be any free interrupts
available for operating PC Cards. You have to reserve the necessary PC card interrupts in the BIOPS setup menu as follows:
Set the necessary interrupt via Advanced > PCI-Configuration >
PCI/PNP ISA IRQ Resource Exclusion to “reserved” (default: available).
!
Caution
Risk of damage to PC cards and the Box PC!
Always insert PC cards with the front face turned toward the rear of the Box PC.
The front face generally bears the company and product designation and is labeled ”This side up”, or words to that effect.
You might damage the Box PC and the PC card if you attempt to insert the PC
card the wrong way round.
Before inserting the connecting cables, the electrostatic charge in your body, the
device and the connecting cables must be brought to the same potential. Briefly
touch the sheet metal case to do this.
Notice
In order to use a PC card the BIOS-SETUP Main > Hardware Option
“Cardbus/PCMCIA Slot” has to be set to “Enabled”.
3-18
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
3.6
Connecting the SIMATIC Box PC 620 to other SIMATIC S5
Point-To-Point Connection
In this section, you will learn how to connect your SIMATIC Box PC 620 to a
programming device or S5 programmable logic controller using a point-to-point
connection.
You can stablish a point-to-point connection by connecting the
SIMATIC Box PC 620 to another programming device or a programmable logic
controller using
A V.24 connection
A TTY connection (optional product feature)
Configuring Interfaces with Line Current (TTY, 20 mA)
To ensure reliable data transfer, several factors must be taken into account. The
maximum data transfer rate (baud rate) depends on the distance, the type of
cable, the pin assignment of the interface and external interference.
You can reduce interference by choosing the right transmission cable and
connecting it properly, and by observing the following guidelines:
Use a shielded cable with a low line resistance (130 W / km) (about 40 W kft)
and low capacitance (< 90 pF/m) (about 27 pF/ft). Twisted-pair cables are less
susceptible to noise and interference. A low line resistance results in reduced
voltage excursions and shorter charge reversal times. The line resistance decreases with increasing conductor cross-section for the same length of cable.
The shorter the transmission link, the higher the maximum possible data
transfer rate.
If there is an active sender and an active receiver at the same end of the
transmission link, the sequence of access priority to the transmission circuit
must be taken into account in order to achieve the longest possible
transmission link.
Signal lines and power lines must not run together. Signal lines must be
installed as far away as possible from sources of strong interference (for
example, 400 V 3-phase power cables).
The active TTY interface with a 12 V no-load voltage has been tested on a 100
m (1100 ft) long cable at a transmission rate of 9600 bps in an environment with
normal levels of noise fieldstrengthV/mor1V/ft).If a shielded 5 x 1 x 0.14shielded
cable is used, reliable transmission is possible over a distance of up to 100 m
(1100 ft). The AS511 protocol (only one transmitter at a time) was used for
testing.
Note
The interference field of the source of interference is reduced by the square of the
distance.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-19
Setting Up and Operating the SIMATIC Box PC 620
Connecting the SIMATIC Box PC 620 to an S5 Programmable Logic Controller
You can connect the Box PC to a SIMATIC S5 programmable logic controller using
the COM1/TTY interface port.
COM 1
(socket)
Figure 3-12 Connecting the Box PC to an S5 Programmable Logic Controller
You connect your Box PC to a SIMATIC S5 programmable logic controller as
follows:
1. Disconnect the Box PC from the power supply.
2. Insert the connecting cable into the port COM 1 / AG.
3. Screw down the plug.
4. Plug the cable into the corresponding port on the CPU of the programmable
logic controller.
5. In order to enable TTY operation, you must set TTY to “enabled” in the BIOS
setup.
!
Caution
Risk of damage !
The interface port may be damaged if you confuse the connections or use the
wrong connecting cables.
Make sure the TTY cable of the SIMATIC Box PC 620is plugged into the
COM 1 / TTY port and not into the LPT 1 port.
Before inserting the connecting cables, the electrostatic charge in your body, the
device and the connecting cables must be brought to the same potential. Briefly
touch the sheet metal case to do this.
Use only original cables to stablish the connection to the programmable controller.
3-20
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
Connecting the SIMATIC Box PC 620 via an Adapter
The connecting cable 6ES5 734-2BD20 is supplied with the Box PC. An adapter is
available for connecting the programmable controller using old standard cables.
Tabelle 3-1
Interface
Adapter for SIMATIC Box PC 620 Connection
Link
Connecting
Cable
Order no:
Adapter
6ES5 734-2BD20
TTY interface Box PC to SIMATIC-S5 program(COM 1)
mable controller
6ES5 731-1xxx0
15–pin
6ES5 731-6AG00
6ES5 731-0xxx0
25– pin
6ES5 731-6AG00
In order to maintain a data transfer rate of 9600 bps up to a distance of over
1000 m (3300 ft), the receiving diode is connected to ground (reference) via the
connecting cable
Note
You can obtain lengths differing from the standard connecting cable
(6ES5 734-2BD20) under the order number 6ES5 734-2xxx0, whereby xxx stands
for the length code.
SIMATIC Box PC 620 Manual
A5E00131465-01
3-21
Setting Up and Operating the SIMATIC Box PC 620
SIMATIC Box PC 620 to PG Connection (V.24, TTY)
If you want to connect your Box PC to another programming device, you can plug
the appropriate connecting cable into the V.24 or TTY interface port
Tabelle 3-2
Connection of the SIMATIC Box PC 620 to other PUs
Interface
Link
Connecting Cable
Order No.:
COM 1 as a
V.24 port
with PG 7xx
6ES5 733-5BD202)
COM 1 as a
TTY port
with PG 6xx
Series connection of
6ES5 733 -2xxx02)
and
6ES5 731-6AG001)
Adapter
6ES5 731-6AG00
Notice
1. When connecting the programming devices in series, make sure you connect
the cable the right way around (see Figure 3-13).
2. The connecting cable is available for order only as a spare part. The connecting cable is described in Chapter 7.
3. The line current (TTY) is an optional product feature.
Adapter
PG 7XX
6ES5 731–6AG00
Connecting cable
Active
Passive
PG 6XX
6ES5 733–2xxx0
Figure 3-13 Direction of Connection: Adapter – Connecting Cable
Notice
For the PC/PU connection, you must switch the TTY ports (COM 1) in one of the
programmable logic controllers to passive by changing the jumper setting. When
the Box PC leaves the factory, this interface is always set to active!
3-22
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
3.7
Connecting the SIMATIC Box PC 620 to a SIMATIC S7 Network
(PROFIBUS/MPI)
Connecting an S7 Programmable Controller via PROFIBUS/MPI Interface
You can connect the SIMATIC Box PC 620 to a SIMATIC S7 automation system
or to a PROFIBUS network via the potentially isolated*) PROFIBUS/MPI port**).
The MPI cable (5m) for connection to SIMATIC S7 CPUs (order no.:
6ES7901-0BF00-0AA0) is supplied with the SIMATIC Box PC 620. Only
transfer rates of up to 187.5 kBit/s are possible with this cable connection. The
12 Mbit/s PROFIBUS connecting cable is required for baud rates from
1.5 Mbit/s ( order no. 6ES7901-4BD00-0XA0).
In disturbed surroundings:
bus connector
6ES7972-0BB10-0XA0
or
6ES7972-0BB20-0XA0
MPI/DP port
6ES7901-0BF00-0AA0
(5 m length
Figure 3-14 Connection Using the PROFIBUS/MPI Interface
Proceed as follows when connecting to a SIMATIC S7 programmable logic controller:
1. Disconnect the PC from the power supply.
2. Connect the cable to the PROFIBUS/MPI interface.
!
Caution
Risk of damage to the SIMATIC Box PC 620!
Before plugging in the cables, the static charge on your body, the unit, and the
cables must be equalized. You can do this by briefly touching the metal mounting
plate for the interfaces on the left-hand side panel.
* Electrical isolation in the saftey extra-low voltage circuit (SELV circuit).
** Optional product feature
SIMATIC Box PC 620 Manual
A5E00131465-01
3-23
Setting Up and Operating the SIMATIC Box PC 620
Connecting
Via the PROFIBUS/MPI interface, you can connect your PC to
MPI networks (S7-200, S7-300, and S7-400) or
PROFIBUS DP networks (DP components).
PROFIBUS/MPI Network
Up to 32 devices (PC, programming device, or programmable controller) can be
connected to the PROFIBUS/MPI interface to form a network segment. The physical connection to the network is via a floating RS485 interface which is a component of the PC basic module.
Several network segments can be connected via repeaters. The complete network
can comprise up to 127 stations. Data transmission rates from 9.6 Kbps to
12 Mbps are possible.
3-24
SIMATIC Box PC 620 Manual
A5E00131465-01
Setting Up and Operating the SIMATIC Box PC 620
3.8
Networking the SIMATIC Box PC 620 with Other Stations on
PROFIBUS
Networking the Box PC on PROFIBUS
PROFIBUS is an open and robust bus system for industrial use. It can be used to
configure networks with up to 32 stations per segment. PROFIBUS-DP supports
data-transfer rates from 9.6 Kbaud to 12 Mbaud.
How the Network Functions
The network operates on the master-slave principle with token passing (complying
with DIN19245, PROFIBUS). It distinguishes between active and passive stations.
An active station receives the token and passes it on to the next station within a
specified time.
Hardware Requirements
Using the following components, for example, you can connect or network the
SIMATIC Box PC 620 with PROFIBUS:
RS 485 MPI/DP interface adapter (Optional product feature)
Shielded, twisted pair (bus cable or connecting cable to network).
SIMATIC Box PC 620 Manual
A5E00131465-01
3-25
Setting Up and Operating the SIMATIC Box PC 620
3.9
Ethernet (RJ45 Ethernet Interface)
Networking Box PC via RJ45 Ethernet Interface
The RJ45 Ethernet interface is a Twisted-Pair (TP) Interface for data transfer rates
of 10/100 Mbaud. This on-board interface is compatible with Intel pro/100+ PCI
Adapters.
The Plug & Play interface is automatically recognized in Windows. Protocols are
configured in the Windows system control.
Notice
A Class 5 Ethernet cable is required for operation with 100 Mbaud.
3.10
Connection under Windows
Windows supports point-to-point connections via the LPT or COM port. The
connecting cables are standard, commercially available products. More information
is available in the Networks section of the Windows description and in the online
Help system under “Connection to Another Computer”.
3-26
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4
What Does This Chapter Contain?
You can enhance the performance of your Box PC by adding additional memory.
This chapter describes how to expand your PC. Please observe the relevant safety
guidelines.
Chapter Overview
In chapter
you will find
on page
4.1
Opening the Unit
4-2
4.2
Installation of a Memory Extension
4-5
4.3
Replacing the Backup Battery
4-10
4.4
Installation of Expansion Cards
4-12
4.5
Removal and Installation of Drives
4-17
4.6
Removal and Installation of the Power Supply Unit
4-22
4.7
Removal and Installation of the Bus Board
4-23
4.8
Removal and Installation of the Motherboard
4-24
4.9
Removal and Installation of the Fan
4-25
4.10
Processor Change
4-26
4.11
Reset Button
4-27
SIMATIC Box PC 620 Manual
A5E00131465-01
4-1
SIMATIC Box PC 620 Expansions
4.1
Opening the Unit
4.1.1
Prerequisites
The device is designed for easy maintenance so that any work that is necessary
can be done quickly and at low cost.
!
Caution
The electronic components on the printed circuit boards are extremely sensitive to
electrostatic discharge. Certain precautionary measures are therefore necessary
when handling such components. These measures are explained in the guidelines
for handling electrostatically sensitive devices at the end of this manual.
Limitation of Liability
All technical specifications and licences apply only to expansion functions
approved by SIEMENS.
No liability can be accepted for impairment of functions caused by the use of
devices and components of other manufacturers.
All the modules and components in the Box PC are electrostatically sensitive.
Please read the ESD guidelines at the end of this book carefully. The following
symbol warns that electrostatically-sensitive modules are present.
4-2
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
Before Opening the Unit
Note the following rules before opening the unit:
Before you disconnect the power supply cable, discharge any electrostatic
charge on your body. You can do this by touching the metal mounting plate for
the interfaces on the left-hand side panel of the unit.
Discharge any electrostatic charge from tools that you are using.
Wear a grounding wrist-strap if you are handling components.
Leave components and modules in their packing until you are ready to install
them.
Disconnect the Box PC from its power supply and remove the battery before
plugging in or removing any modules or components.
Touch components and modules only on their edges. Above all, do not touch
the connecting pins and printed conductors.
Never operate the Box PC with the cover open.
Tools
You can carry out all necessary installation work on the Box PC with screwdrivers
of the type TORX T10 and TORX T8.
SIMATIC Box PC 620 Manual
A5E00131465-01
4-3
SIMATIC Box PC 620 Expansions
4.1.2
Opening the SIMATIC Box PC 620
To open the Box PC, proceed as follows:
1. Pull out the power supply connector, and remove all connecting cables from the
unit, including the keyboard cable.
2. Remove the PC from its mounting/cabinet (only necessary if screws which have
to be removed are inaccessible in the fitted position).
3. Undo the two screws (see fig. 5-1) on the housing cover.
4. Raise the cover slightly.
5. Then you can remove the housing cover.
Screws on the housing cover
Figure 4-1 Box PC 620 Prepared for Opening
4-4
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.1.3
Components Visible After Opening the Unit
Components
Once you have removed the top cover of your unit, the components are visible.
Floppy drive or LS 240
Power supply unit
Bus board
Memory extension
Processor
Fan
Figure 4-2 Box PC 620 Open
SIMATIC Box PC 620 Manual
A5E00131465-01
4-5
SIMATIC Box PC 620 Expansions
4.1.4
The Motherboard
S1
X401
X28
X128
X1
X29
X24
X20
X19
X500
X600
X40
X11
X9
X6
X14
X700
X10
X70
X25
X13
T3
X26
X41 X4
X5
X71
X3
X31
T2
X420
T1
X23
X44
X400
X402
The motherboard is the heart of the Box PC. Here, data is processed and stored,
and interfaces and device I/Os are controlled and managed.
Figure 4-3 Motherboard
4-6
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
Components on the Motherboard
The following components are located on the motherboard of the Box PC 620 V2:
Number
Functions
X1
Processor module with heat sink
X3
IDE connector for CD-ROM
X4
IDE connector for 2.5 “ hard disk
X5
Floppy drive connector
X6
PS/2 mouse connection
X6
PS/2 keyboard connection
X9
Serial port COM 1/TTY
X9
Parallel port LPT 1
X11
Serial port COM 2
X11
Socket for VGA monitor
X13
Connection to power supply 105W
X14
Connection to power supply 85W
X19, X20
System memory, 2 slots
X23
No connected
X24
Connector for clock battery
X26
Connector alternative COM2
X28
No connected
X29
Connector for CPU fan
X31
IDE connector for LS 120
X40
USB bus connector
X41
IDE connector for 3.5 “ hard disk
X44
Connector for front interface
X70, X71
TTY tranmitter/receiver *1
X128
Connector for device fan
X400
Connector for LVDS display (3.3 V/5 V)
X401
No connected
X402
No connected
X420
Connector for 5 V CMOS display
X500
RJ45 socket for ethernet LAN
X600
MPI/DP port
X700
PC card slot
S1
Button for hardware reset
T1
Temperature sensor (in the processor)
T2
Temperature sensor
T3
Temperature sensor
*1
Optional product feature
SIMATIC Box PC 620 Manual
A5E00131465-01
4-7
SIMATIC Box PC 620 Expansions
4.2
Installing Memory Expansion Submodules
Standard Memory
The motherboard has 2 slots for 144 pin SO DIMM memory submodules. This
allows you to expand the memory capacity of your Box PC 620 to a maximum of
512 Mbytes.
Either one or two modules can be installed.
Memory
Modules
64 Mbytes
128 Mbytes 256 Mbytes
64 Mbytes
1
–
–
128 Mbytes
2
–
–
128 Mbytes
–
1
–
192 Mbytes
1
1
–
256 Mbytes
–
–
1
256 Mbytes
–
2
–
384 Mbytes
–
1
1
512 Mbytes
–
1
–
Bank 0
Bank 1
Figure 4-4 Position of the SO DIMM Memory modules
4-8
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
!
Caution
The electronic components of the printed circuit boards are extremely sensitive to
electrostatic discharge. Certain precautionary measures are therefore necessary
when handling such components. These measures are explained in the guidelines
for handling electrostatically sensitive devices at the end of this manual.
Installing the SO DIMM Cards
To plug in expansion submodules, proceed as follows:
1. Open the unit as described in Section 4.1.
2. Plug the cards into the slots. Note the safety recess on the connector side of
the SO DIMM card.
3. Push the card down applying light pressure until it locks into place.
4. Close the unit.
!
Caution
Risk of damage!
Make sure that the cards sit securely in the slots, otherwise they can fall out and
be damaged.
Installation
The memory configuration is detected automatically. When you switch on the unit,
the distribution of base and extended memory is displayed on the screen.
SIMATIC Box PC 620 Manual
A5E00131465-01
4-9
SIMATIC Box PC 620 Expansions
4.3
Replacing the Backup Battery
Battery Power Supply for Real-Time Clock and Configuration
A backup battery (3.6 V-lithium battery) powers the the real-time clock even after
the device is switched off. In addition to the time of day, all the information about
the Box PC (device configuration) is stored in RAM. If the backup battery fails or is
removed, all these data are lost.
The clock uses very little power and the lithium battery has a high capacity so that
the battery can provide backup power for the real-time clock for many years and
seldom needs to be replaced.
Battery Voltage too Low
If the battery voltage is too low, the time is lost, and a correct configuration of the
device can no longer be guaranteed.
Replacing tthe Battery
In this case, you must replace the backup battery. The battery is on the
motherboard.
To change the battery, proceed as follows:
1. Disconnect the PC from the power supply and remove all the connecting cables.
2. Open the unit as described in Section 4.1.
3. Change the backup battery inserted in the motherboard by pulling out the
connector and undoing the cable tie.
4. Secure the new battery in its mounting with a cable tie.
5. Insert the battery connector in the motherboard.
6. Close the unit.
4-10
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
Backup battery
Figure 4-5 Position of the Backup Battery
!
Caution
Risk of damage!
Only replace the lithium battery with an identical battery or with a type
recommended by the manufacturer (Order No.: W79084-E1003-B1).
Dispose of used batteries in keeping with local regulations.
Changing SETUP
If you change the battery or unplug the battery connector you must run the SETUP
program to reset your programming device’s configuration data (see Chapter 5).
SIMATIC Box PC 620 Manual
A5E00131465-01
4-11
SIMATIC Box PC 620 Expansions
4.4
Installation of Expansion Cards
Notes about the Cards
The Box PC is designed for the use with cards as per the AT/PCI specification.The
dimensions of the cards may not exceed the stated dimensions. If the height is exceeded, contact problems, malfunctions and difficulties with the assembly cannot
be excluded. The illustrations show cards with a full AT/PCI overall length.
Depending on the slot, there may be restrictions on the overall length.
106,7 mm
4,201”
175 mm
6,89 ”
A31
A1
Figure 4-6 XT Card
121,92 mm
4,8”
175 mm
6,89 ”
C18
C1
A31
A1
Figure 4-7 AT Card
4-12
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
106,68 mm
4,2”
8,19 mm
0.322”
174,63 mm
6,875”
Figure 4-8 Short PCI Cards (5 V)
106,68 mm
4,2”
8,19 mm
0.322”
265 mm
10,48 ”
Figure 4-9 Long PCI Cards (5 V)
Note about Long PCI Cards
Before long PCI cards can be inserted into the guides of the fan trough, they must
be fitted with a so-called extender (this should form part of the scope of supply of
long PCI boards). Long PCI cards can be inserted into the guides of ISA modules
by means of this extender.
SIMATIC Box PC 620 Manual
A5E00131465-01
4-13
SIMATIC Box PC 620 Expansions
4.4.1
Removal and Installation of the Device for Holding Down the
modules
The device for holding down the modules is attached to the housing with a screw.
It has three slits, through which the slide elements are inserted.
Proceed as follows:
1. Open the housing as described in Section 4.1.
2. Undo the fixing screw of the device for holding down the modules.
3. During assembly, ensure that the device for holding down the modules is
resting on the guide on the housing.
Guide slits for slide elements
Fixing screw for device for
holding down the modules
Figure 4-10 Removal/Installation of an Expansion Card
Note
The slide elements are in the enclosed plastic bag.
4-14
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
Aligning the Holding-Down Device
Proceed as follows to install the holding-down device.
1. Insert the slide element through the guide slit until it is resting firmly on the
module. The module must now be introduced into the notch.
!
Caution
No pressure may be exerted on the module! Therefore, do not use force to press
the slide element onto the module.
2. Cut off the projecting part of the slide element:
– Score the slide element at the top edge of the holding-down device with a
knife and break it off.
– Nip off the surplus with a sharp side cutter.
SIMATIC Box PC 620 Manual
A5E00131465-01
4-15
SIMATIC Box PC 620 Expansions
4.4.2
Removal and Installation of an Expansion Card
Proceed as follows:
1. Open the housing as described in Section 4.1.
2. Remove all connectors from the expansion card and note the assignment.
3. Remove the device for holding down the modules as described in Section 4.4.1.
4. Undo the screw on the slot plate of the module.
5. Pull the module out of the slot.
6. Proceed in the reverse order to install the new expansion card.
Slots for expansion cards
Device for holding down the modules
Figure 4-11 Removal/Installation of an Expansion Card
4-16
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.5
Removal and Installation of Drives
4.5.1
Removal and Installation of the Hard Disk Drive
1. Undo the 4 screws on the back of the housing.
2. Open the drive holder.
3. Detach the drive holder from the mounting and lay the drive holder with its top
on the housing.
4. Note the cable assignment and pull off the cables.
5. Undo the four screws which secure the hard disk drive to the vibration-damped
part of the mounting. Remove the hard disk drive from the mounting.
6. Proceed in the reverse order to fit the new drive. The new drive must be of the
same type as the one removed.
Fixing screws
Figure 4-12 Installation and Removal of the Drive Holder
SIMATIC Box PC 620 Manual
A5E00131465-01
4-17
SIMATIC Box PC 620 Expansions
Figure 4-13 Hard Disk Drive with Holder Removed
4-18
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.5.2
Removal and Installation of a CD ROM Drive
Depending on the device equipment, a CD ROM drive is installed in the Box PC.
1. Undo the 2 screws on the back of the housing.
2. Remove the cover of the CD ROM drive.
3. Undo the three screws which secure the CD ROM drive to the mounting.
4. Remove the CD ROM drive from the mounting and carefully pull off the data
cable.
5. Proceed in the reverse order to fit the new drive.
Fixing screws for CD ROM cover
CD ROM drive with cover
Figure 4-14 Box PC 620 with CD ROM Drive
SIMATIC Box PC 620 Manual
A5E00131465-01
4-19
SIMATIC Box PC 620 Expansions
4.5.3
Removal and Installation of the Floppy Drive
1. Open the housing as described in Section 4.1.
2. Remove the drive holder as described in Section 4.5.1.
3. Release the interlock of the controller flex-lead on the motherboard and pull the
flex-lead out of the connector assembly.
4. Undo the two fixing screws (TORX T8) on the housing.
5. Lift the floppy drive upwards out of the housing.
6. Proceed in the reverse order to fit the new drive. The new drive must be of the
same type as the one removed.
Fixing screws of the floppy drive
Figure 4-15 Installation of the Floppy Disk Drive in the Box PC 620
4-20
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.5.4
Removal and Installation of the LS 240 Drive
The removal and installation of the LS240 drive takes place with the same steps as
for the floppy drive.
1. Open the housing as described in Section 4.1.
2. Remove the drive holder as described in Section 4.5.1.
3. Release the cable clamp assembly of the controller flex-lead on the
motherboard and pull the flex-lead out of the connector assembly.
4. Undo the two fixing screws (TORX T8) on the housing.
5. Lift the LS 240 drive upwards out of the housing.
6. Proceed in the reverse order to fit the new drive.
Screw for LS 240 cable clamp assembly
Fixing screws of the LS 240 drive
Figure 4-16 Installation of the LS 240 Drive
SIMATIC Box PC 620 Manual
A5E00131465-01
4-21
SIMATIC Box PC 620 Expansions
4.6
Removal and Installation of the Power Supply Unit
1. Open the system housing as described in Section 4.1.
2. Remove the drive holder as described in Section 4.5.1.
3. Undo and remove the 3 screws of the cover of the power supply unit from the
housing
4. Remove the internal power supply cable from the power supply unit
(only versions with the 105W power supply)
5. Undo the two fixing screws (TORX T10) on the housing.
6. Pull the power supply unit upwards out of the housing.
7. Proceed in the reverse order to fit the new power supply unit.
Cover of the power supply unit
Power supply unit
Figure 4-17 Removal and Installation of the Power Supply Unit
4-22
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.7
Removal and Installation of the Bus Board
1. Open the housing as described in Section 4.1.
2. Remove all the modules from the slots (proceed as described in Section 4.4.2).
3. Remove the drive holder as described in Section 4.5.1.
4. Remove the power supply unit as described in Section 4.6.
5. Undo the screw on the motherboard.
6. Pull the bus board off the motherboard.
7. Proceed in the reverse order to refit the bus board.
Bus board
Fixing screw of the bus board
Figure 4-18 Removal and Installation of the Bus Board
SIMATIC Box PC 620 Manual
A5E00131465-01
4-23
SIMATIC Box PC 620 Expansions
4.8
Removal and Installation of the Motherboard
1. Open the housing as described in Section 4.1.
2. Remove all the modules from the slots (proceed as described in Section 4.4.2).
3. Remove the drive holder as described in Section 4.5.1.
4. Remove the power supply unit as described in Section 4.6.
5. Undo the 7 screws on the motherboard and the 10 hexagon head screws on the
ports.
6. Remove the bus board and the motherboard.
7. Proceed in the reverse order to refit the motherboard.
Fixing screws on the motherboard
Figure 4-19 Fixing Screws on the Motherboard
The motherboard is available as a replacement part without the processor, memory
modules and bus board .
4-24
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.9
Removal and Installation of the Device Fan
The Box PC is cooled by means of a fan which sucks hot air out of the housing.
1. Open the housing as described in Section 4.1.
2. Pull off the fan cable connector on the basic board.
3. The fan is secured to the housing by two plastic rivets. Undo the rivets by
pressing out the gudgeon from the rear of the rivet shank.
4. Remove the fan.
5. Proceed in the reverse order for assembly.
Plastic rivets
Device fan
Figure 4-20 Removal and Installation of the Device Fan
Notice
Only a fan of the same type may be fitted!
!
Caution
To ensure that the device is adequately cooled, take care that the running direction
of the fan is correct when installing.
Ensure that the arrow on the fan points to the housing wall.
SIMATIC Box PC 620 Manual
A5E00131465-01
4-25
SIMATIC Box PC 620 Expansions
4.10
Processor Change
Proceed as follows to exchange the processor:
1. Pull out the fan cable plug.
2. Remove the cooling unit which is fixed using a lifting lever.
3. Then push the lever in the direction of the arrows (1) and swing it upwards as
far as it will go (2).
4. Lift the old processor out of the slot (3).
5. Put the new processor in its socket and make sure that the marks on top of the
processor have the exact position (4) as indicated on the slot (A).
Caution
The marks on top of the processor may be covered by the cooling unit. In this
case, use the marks between the pin rows on the outside of the processor.
6. Swing the lever downwards until it clicks into position (5).
7. Unmount the fan.
8. Fix the cooling unit using the lifting lever.
9. Reattach the fan cable plug to the motherboard.
10.Mount the fan.
Caution
Operating a processor at a higher frequency than the maximum permissible
frequency may result in destruction of the processor, data loss, or data corruption.
3
2
4
5
1
A
Figure 4-21 Changing the Processor
4-26
SIMATIC Box PC 620 Manual
A5E00131465-01
SIMATIC Box PC 620 Expansions
4.11
Reset Button
A hardware reset is initiated by means of the reset button on your device. The PC
is restarted.
In the Box PC the reset button is on the drive side beside the floppy drive. The reset button can be only actuated with a thin pen (e.g. an opened-up paper clip). The
position of the reset button is marked in the illustration of the Box PC below.
Reset button
Figure 4-22 Reset Button
SIMATIC Box PC 620 Manual
A5E00131465-01
4-27
SIMATIC Box PC 620 Expansions
4-28
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
5
What Does This Chapter Contain?
In this chapter, you will learn how to configure your programming device. You need
to do this if you change your system by adding, removing, or exchanging
expansion modules and memory expansions, or by replacing a system module.
Chapter Overview
In chapter
you will find
on page
5.1
Changing the Device Configuration with BIOS SETUP
5-2
5.1.1
The Main Menu
5-5
5.1.2
The Advanced Menu
5-15
5.1.3
The Security Menu
5-22
5.1.4
The Power Menu
5-24
5.1.5
The Boot Sequence Menu
5-25
5.1.6
The Version Menu
5-27
5.1.7
The Exit Menu
5-28
5.1.8
Default Setup Settings
5-29
5.2
Configuring the PCMCIA Interface
5-32
SIMATIC Box PC 620 Manual
A5E00131465-01
5-1
Titel chapterthe SIMATIC Box PC 620
Configuring
5.1
Changing the Device Configuration with BIOS SETUP
Changing the Device Configuration
Your Box PC device configuration is set for working with the software supplied with
the unit. You should only change the preset values if you have modified your
Box PC in any way or if a fault occurs when the unit is powered up.
BIOS SETUP Program
The SETUP program is in the ROM-BIOS. Information about the system
configuration is stored in the battery-backed RAM of the Box PC.
You can use SETUP to set the hardware configuration (for example, hard disk
type) and define the system characteristics. You can also use SETUP to set the
time of day and date.
Incorrect BIOS Data
If incorrect BIOS data are detected when you boot the system, the BIOS prompts
you to
S
Start BIOS SETUP by pressing F2 or
S
Continue booting by pressing F1.
Starting SETUP
On completion of the startup test, the BIOS gives you the opportunity of starting
the SETUP program by displaying the following screen prompt:
PRESS < F2 > to enter SETUP
To start SETUP, proceed as follows:
1. Reset your PC (warm or cold restart).
2. Press the F2 key as long as the BIOS prompt appears on the screen.
BIOS SETUP Menus
The various menus and submenus are listed on the following pages. You can get
all the information you need for the SETUP entry selected from the
“Item Specific Help” part of the relevant menu.
5-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Screen Display Following Power On
With the default setting of your PC, the display shown below appears following
power-on:
Phoenix BIOS 4.0 A5E00123801–ES02
Copyright 1985-2001 Phoenix Technologies Ltd.
All Rights Reserved.
SIMATIC Box PC 620 V02.01.02
CPU = PentiumIII 866MHz
637K System RAM Passed
119MB Extended RAM Passed
0128K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
UMB upper limit segment address: ....
Fixed Disk 0: xxxx
ATAPI CD-ROM: Txxx
Mouse initialized
Press <F2> to enter SETUP
If you press the F2 key while the above display is shown, you select the
ROM-based BIOS setup program. In this program, you can set a number of
system functions and hardware configurations of your programming device.
The default settings are effective on delivery. You can change these settings using
the BIOS setup. The modified settings become effective when you have
saved them and terminated the BIOS setup.
The following screen shots may differ from what is shown here, depending on the
device configuration. The following screen form appears when you start the BIOS
setup:
PhoenixBIOS Setup Utility
Header
Menu bar
Selectable
submenu
Operation line
Figure 5-1
Main
Advanced
Security
Power
System Time:
System Date:
[ 15:35:32 ]
[ 03/12/2002]
Diskette A:
Primary Master
Primary Slave
Secondary Master
Secondary Slave
[1.44 MB, 31/2”]
[20496 MB]
[None]
[CD–ROM]
[None]
Memory Cache:
[Write Back]
Boot Options
Keyboard Features
Hardware Options
System Memory:
Extended Memory:
640 KB
121856 KB
F1
ESC
Help
Exit
Boot Sequence
Version
Exit
Item Specific Help
<Tab>, <Shift-Tab>,
<Enter> selects field.
Example:
Hour/Minute/Second
Month/Day/Year
or
Help window
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
SETUP Main Menu (Example)
SIMATIC Box PC 620 Manual
A5E00131465-01
5-3
Configuring the SIMATIC Box PC 620
Menu Structure
The screen is divided into four sections. In the top section, you can select the
menu screens [Main], [Advanced], [Security], [Power], [Boot Sequence],
[Version], [Exit]. In the left of the center section you can select various settings or
submenus. Brief help texts appear on the right for the currently selected menu
entry. The bottom section contains information for operator inputs.
Yellow stars to the left of the interface designation (for example, Internal COM 1)
indicate a resource conflict between the interfaces managed by the BIOS. In this
case you should select the default settings (F9) or eliminate the conflict.
You can move between the menu screens using the cursor keys [←] and [→].
Menu
5-4
Meaning
Main
System functions are set here
Advanced
An extended sytem configuration can be set here
Security
Security functions are set here, for example a password
Power
Power functions can be selected here
Boot Sequence
The boot priorities are defined here
Version
Information about the programming device’s release status
Exit
Used for terminating and saving
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
5.1.1
The Main Menu
PhoenixBIOS Setup Utility
Main
Selectable
submenu
Advanced
Power
System Time:
System Date:
[ 15:35:32 ]
[ 03/12/2002 ]
Diskette A:
Primary Master
Primary Slave
Secondary Master
Secondary Slave
[1.44 MB, 31/2”]
[20496 MB]
[None]
[CD–ROM]
[None]
Memory Cache:
[Write Back]
Boot Options
Keyboard Features
Hardware Options
System Memory:
Extended Memory:
F1
ESC
Figure 5-2
Security
Help
Exit
Boot Sequence
Version
Exit
Item Specific Help
<Tab>, <Shift-Tab>,
<Enter> selects field.
Example:
Hour/Minute/Second
Month/Day/Year
or
Help window
640 KB
62976 KB
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
SETUP Main Menu (Example)
Setting in the Main Menu
In the Main menu, you can move upwards and downwards using the cursor keys
[↑] and [↓] to select the following system parameters:
Field
Meaning
System Time
For viewing and setting the current time
System Date
For viewing and setting the current date
Diskette A
Type of built in floppy disk drive
With LS 240 drive [Disabled]
Memory Cache
For setting the cache options
by submenus
Primary Master
Type of build in drives
Secondary Master
Type of build in drives
Boot Options
For setting boot options
Keyboard
Features
For setting keyboard interface options (e.g. NUM Lock, Typematic
Rate)
Hardware Options
For setting hardware options
SIMATIC Box PC 620 Manual
A5E00131465-01
5-5
Configuring the SIMATIC Box PC 620
System Time und System Date Uhrzeit und Datum
System Time and System Date indicate the current values. Once you have
selected the appropriate option, you can use the [+] and [–] keys to modify the time
setting
Hour:Minute:Second
and the date
Month/Day/Year.
You can move between the entries in the date and time options (for example, from
hour to minute) using the tabulator key.
Diskette A Disk drive
The type of floppy drive installed in the PC is set here. The following entries are
possible:
[Disabled]
If there is no disk drive or LS 240 drive. Default setting for an installed
LS 240 drive.
[360 KB,5 1/4”]
[1.2 MB,5 1/4”]
[720 KB,3 1/2”]
[1.44 MB, 3 1/2”]
Default setting for an installed disk drive A
[2.88 MB, 3 1/2”]
5-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Primary Master Primary Slave Secondary Master/ Secondary Slave
The system jumps to the following submenu when you select this type of menu
field:
PhoenixBIOS Setup Utility
Main
Primary Master [20496 MB]
[ Auto ]
Type:
Total Sectors:
Maximum Capacity:
LBA Format
40031712
20496 MB
Multi-Sector Transfers:
LBA Mode Control:
32 Bit I/O:
Transfer Mode:
Ultra DMA Mode:
F1
ESC
Figure 5-3
Help
Exit
[16 Sectors]
[Enabled]
[Enabled]
[FPIO 4 / DMA 2]
[Disabled]
Select Item
Select Menu
Item Specific Help
[Auto] (recommended)
Autotypes installed
IDE-devices
[USER]
Enter parameters of
IDE-devices installed
at this connection
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Primary Master
“Type” Field
The parameters you can select here are usually stored on the IDE drive. The ’Auto’
setting in the ’Type’ field means that these values are automatically read from the
drive and written into memory (Autodetect).
If Type is selected for a drive that cannot be detected, a timer times out in
approximately 1 minute and the entries remain unchanged. You should always
check that the interfaces for which you select ’Auto’ are in fact connected to drives.
Select “User” if you want to define the hard-disk type yourself, in which case
remember that you also have to set the other fields, including Cylinder, Heads,
Sectors/Track and WritePrecomp, to the correct values for the type of hard disk in
question.
SIMATIC Box PC 620 Manual
A5E00131465-01
5-7
Configuring the SIMATIC Box PC 620
“Multi Sector-Transfer” Field
The entry in the Multi-Sector Transfer field defines the number of sectors
transferred per interrupt. The value depends on the drive and should be set only by
setting the Type field to Auto.
Disabled
2,4,8,16
sectors
“LBA Mode Control” field
If the LBA Mode Control field (enabled,disabled) is set to ’Enabled’, the system
supports hard disks with capacities greater than 528 Mbytes. The value depends
on the drive and should be set only by setting the Type field to Auto.
“32 Bit-IO” Field
The setting in the 32 Bit I/O field defines the mode of access for the drive
Disabled
16-Bit access
Enabled
32-Bit access
(default)
“Transfer Mode” and “Ultra DMA Mode” Fields
The settings in these fields define the interface’s data-transfer rate. The value
depends on the drive and should be set only by setting the Type field to Auto.
Hit ESC to exit the submenu.
5-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
”Memory Cache” Submenu
The following pop-up menu appears when you select the submenu “Memory
cache” in the main menu:
PhoenixBIOS Setup Utility
Main
System Time:
System Date:
Diskette A:
[ 15:35:32 ]
[ 03/12/2002 ]
[1.44 MB, 31/2” ]
Primary Master
Primary Slave
Secondary Master
Secondary Slave
[20496 MB]
[None]
[CD–ROM]
[None] Disabled
Write Through
Write Back
[Write Back]
Memory Cache:
Item Specific Help
Controls caching of
system conventional
memory and memory
above one megabyte.
Boot Options
Keyboard Features
Hardware Options
System Memory:
Extended Memory:
F1
ESC
Figure 5-4
Help
Exit
640 KB
121856 MB
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
“Memory Cache” Field
A cache is a fast memory buffer between the CPU and main memory (DRAM).
Recurrent memory access operations are executed in the fast cache, instead of
the main memory, if the function is enabled. In rare instances involving some
hardware and software combinations, it may be necessary to disable the cache
because the program runtimes or waits are too short on account of the fast cache.
[Disabled]
Cache is disabled
[Write Through]
Write access is not concluded until the entry has been made in main
memory
[Write Back]
Write access is concluded immediately; the entry in main memory
takes place in the backround (default)
SIMATIC Box PC 620 Manual
A5E00131465-01
5-9
Configuring the SIMATIC Box PC 620
”Boot Options” Submenu
The following submenu appears when you select the option “Boot Options” in the
main menu:
PhoenixBIOS Setup Utility
Main
Boot Options
QuickBoot Mode:
[Enabled]
SETUP prompt:
POST Errors:
[Enabled]
[Enabled]
Floppy check:
[Disabled]
Summary screen:
[Enabled]
F1
ESC
Figure 5-5
5-10
Item Specific Help
Help
Exit
Select Item
Select Menu
Allows the system to
skip certain tests
while booting. This
will decrease the
time needed to boot
the system.
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
”Boot Options” Submenu
Quick Boot
Mode
Some hardware tests are skipped to speed up the boot procedure.
SETUP prompt
The message PRESS <F2> to enter Setup appears at the bottom of the
screen during the system run-up phase.
POST Errors
The boot process is stopped if an error is detected; you must press F1 to
acknowledge. Enter “Disabled”to avoid the necessity of acknowledging
errors, for example if no keyboard is connected.
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Floppy check
The floppy head is stepped inward and then back to its original position
during the system run-up phase. This test is useful because it
reinitializes the drive.
Summary
screen
The most important system parameters are displayed when the system
run-up phase completes.
’Enabled’ means that the feature is active. ’Disabled’ means that the feature is
inactive.
Example of a summary screen:
PhoenixBIOS Setup Utility
SIMATIC Box
CPU Type
CPU Speed
: PC 620
: Pentium(R) III
: 866 MHz
BIOS Number
System ROM
BIOS Date
: A5E00123801–ES02x
: E6E3 – FFFF
: 03/12/02
System Memory
Extended Memory
Shadow Ram
Cache Ram
: 640 KB
: 119 MB
: 384 KB
: 512 KB
COM Ports
LPT Ports
Display Type
PS/2 Mouse
: 03F8
: 0378
: VGA
: Installed
Hard Disk 0
Hard Disk 1
Hard Disk 2
Hard Disk 3
: 20496 MB
: None
: CD–ROM
: None
Diskette A
: 1,44 MB, 31/2 ”
Figure 5-6
Summary Screen
The Summary screen appears when the system run-up phase completes.
SIMATIC Box PC 620 Manual
A5E00131465-01
5-11
Configuring the SIMATIC Box PC 620
“Keyboard Features” Submenu
The following submenu appears if you select the “Keyboard Features” field in the
main menu:
PhoenixBIOS Setup Utility
Main
Keyboard Features
Item Specific Help
[ On ]
NumLock:
Key Click:
[Disabled]
[30/sec]
Keyboard auto-repeat rate:
Keyboard auto-repeat delay: [1/2 sec]
F1
ESC
Figure 5-7
5-12
Help
Exit
Select Item
Select Menu
Selects Power-On state
for NumLock on next boot
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”Keyboard Features”Submenu
Numlock
Switches Numlock on or off following power on
Key Click
A keystroke can be heard
Keyboard auto-repeat
rate
Increase in automatic key repeat rate
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
”Hardware Options” Submenu
The following submenu appears when you select the “Hardware Options” field in
the main menu:
PhoenixBIOS Setup Utility
Main
Hardware Options
Item Specific Help
PCI – MPI / DP:
Onboard Ethernet:
Ethernet Address:
LAN Remote Boot:
Cardbus/PCMCIA Slot:
SafeCard functions:
Legacy USB Support:
Fan Control:
CRT / LCD selection:
LCD-Screensize:
DSTN Contrast:
[ Enabled ]
[Enabled]
08000624xxxx
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[SIMULTAN]
[Expand]
[154]
PS/2 Mouse:
[Enabled]
F1
ESC
Figure 5-8
Help
Exit
Select Item
Select Menu
Enable or disable the
PCI - Multi Point
Interface (MPI/DP)
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”Hardware Options” Submenu
The parameters of the interfaces present on the basic module are set here.
Entry
Meaning
PCI-MPI/DP *1
Enables the CP5611-compatible MPI/DP interface. The recourses are
managed by the BIOS PCI plug and play mechanism.
On Board
Ethernet
[Enabled]
The ethernet port on the motherboard is enabled.
[Disabled]
The ethernet port on the motherboard is disabled.
Ethernet
Address
The individual ethernet address is displayed here.
LAN Remote
Boot
[Enabled]
Booting using a connected LAN is possible. The
respective boot source is displayed as
Intel Boot-Agent in the boot sequence menu.
[Disabled]
Booting using LAN is not possible.
*1
Optional product feature
SIMATIC Box PC 620 Manual
A5E00131465-01
5-13
Configuring the SIMATIC Box PC 620
Entry
Cardbus /
PCMCIA Slot
SafeCard
functions
Meaning
[Disabled]
Disables the Cardbus / PCMCIA interfaces.
[Enabled]
The resources are managed by the BIOS
PCI plug and play mechanism.
[Enabled]
On board monitoring functions are enabled.
[Disabled]
No monitoring functions.
The relevant driver and the application must be started for operation of
the monitoring functions.
Legacy USB
Support
[Disabled]
A USB-capable operating system is required to
operate a USB keyboard or a USB mouse.
Setup adjustments can be made with a USB keyboard.
[Enabled]
USB keyboard and USB mouse are supported by the
BIOS. Non-USB capable operating systems can be
used.
Fan Control
[Enabled]
[Disabled]
Fan speed depends on temperature.
Fan always runs at full speed.
CRT / LCD
selection
[LCD Enabled]
All data is output only to the internal LCD,
the 15-way VGA port is disabled
For maximum resolution the display signals are output
only to the 15-way VGA port; the LCD interface of the
VGA controller is disabled.
LCD-Screensize
5-14
[CRT Enabled]
[SIMULTAN]
Both display interfaces are enabled and operate
simultaneously. Note, however, that the LCD does not
support all resolutions.
[Normal]
The display window in Text and Graphic modes is not
expanded to full screen size.
[Expanded]
Die volle Bildschirmgröße wird genutzt, auch wenn
die Auflösung nicht die Pixelgröße des Bildschirms
hat.
DSTN Contrast
The contrast of the DSTN displays is set here.
Range: 0-255
PS/2 Mouse
[Internal]
The PS/2 port is activated.
This is the default for the Box PC. IRQ 12 is assigned.
[Disabled]
The PS/2 port is deactivated, IRQ12 is available.
[Autodetect]
It is automatically detected if a mouse is connected.
Note:
Invariably, changes to this interface do not come into
effect until the PC is switched off and on again.
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
5.1.2
The Advanced Menu
Menu Structure
PhoenixBIOS Setup Utility
Advanced
Main
Security
Power
Boot Sequence
Version
Exit
Item Specific Help
Setup Warning
Setting items on this menu to incorrect values may
cause your system to malfunction
COM/LPT Configuration
PCI Configuration
[ Other ]
[ No ]
[Enabled]
[Both]
[DOS]
[Disabled]
Installed O/S:
Reset Configuration Data:
Floppy disk controller:
Local Bus IDE adapter:
Large Disk Access Mode:
Memory Gap at 15 Mbyte:
Select the operating
system installed
on your system which
you will use most
commonly.
Note: An incorrect
setting can cause
some operating
systems to display
unexpected behavior.
Video Adapter Settings
F1
ESC
Figure 5-9
Help
Exit
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
“Advanced” Menu
Setting in the Advanced Menu
Installed O/S
Plug and Play means that all modules are automatically detected and
installed, providing they support the Plug and Play functionality.
[other]
BIOS handles the entire Plug and Play capability,
default configuration
[Win95], [Win98], The operating system handles some of the Plug
[WinMe], [Win2000] and Play functions
Reset
Configuration
Data
[Yes]
All installations under Plug and Play are deleted and
reconfiguration is triggered the next time the system
boots. The entry is then reset to [No]. System
components that do not support Plug and Play have
to be entered manually.
Floppy Disk
Controller
[Enabled]
Floppy Disk Controller on the motherboard is
activated.
[Disabled]
Floppy Disk Controller on the motherboard is
deactivated (with LS 240 drive).
SIMATIC Box PC 620 Manual
A5E00131465-01
5-15
Configuring the SIMATIC Box PC 620
Local Bus IDE
adapter
[Primary]
[Secondary]
[Both]
Large Disk
Access Mode
Memory Gap at
15 MByte
Primary IDE interface for max. two drives is
activated.
Secondary IDE interface for max. two drives is
activated.
Both IDE interfaces for max. four drives are
activated.
[Disabled]
No local IDE interface is activated.
[DOS]
The drive tables are adapted for DOS access
operations in accordance with Enhanced IDE.
[OTHER]
The tables are not adapted.
[Disabled]
[Enabled]
The complete onboard RAM memory is available.
A 1MB area of the RAM above 15MB
(Addresses F0 0000 – FF FFFF) can be used by ISA
expansion cards.
Submenu COM/LPT Configuration
PhoenixBIOS Setup Utility
Advanced
COM/LPT Configuration
Item Specific Help
Internal COM 1:
Base I/O address:
Interrupt:
Internal COM2:
Base I/O address:
Interrupt:
[Enabled]
[3F8]
[IRQ 4]
[Enabled]
[2F8]
[IRQ 3]
Internal LPT1:
Mode:
Base I/O address:
Interrupt:
[Enabled]
[Output only]
[378]
[IRQ 7]
Configure serial port A
using options:
[Disabled]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
[OS Controlled]
Displayed when
controlled by OS
F1
ESC
Figure 5-10
Help
Exit
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”COM/LPT Configuration” Submenu
The resources used by an interface are released when you disable the interface in
question.
The I/O addresses and interrupts are preassigned to be operated as COM1,
COM2 and LPT1 and we recommend you use them accordingly.
5-16
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Printer Port Internal LPT1
Mode:
Use this setting to set the operating mode of the printer interface. Refer
to the table below to ensure that the setting matches the printer
connected to the printer port.
Settable Mode
Features
Output Only
S Standard setting for the 8 bit parallel transfer
Standard parallel port –
unidirectional (SPP)
S Feedback of the output device is only possible via
Bidirectional
as for SPP – unidirectional, however:
Standard parallel port –
bidirectional
S Feedback of the output device is also possible via
EPP
S Enhanced parallel port (data transfer rate from
according to IEEE1284 specifications
the control cables
the 8 bit data cables
500kbps up to 2Mbps)
Enhanced parallel port
S Hardware handshake
S different devices can be addressed
ECP
as for EPP, however:
Extended capability port
S own DMA channel
S FIFO backup
S Data compression
PCI Configuration Submenu
PhoenixBIOS Setup Utility
Advanced
PCI Configuration
Item Specific Help
PCI Device, Slot #1
PCI Device, Slot #2
Setup items for configuring
The specific PCI device
PCI/PNP ISA IRQ Resource Exclusion
PCI
PCI
PCI
PCI
F1
ESC
Figure 5-11
SIMATIC Box PC 620 Manual
A5E00131465-01
IRQ
IRQ
IRQ
IRQ
Help
Exit
line
line
line
line
1:
2:
3:
4:
[Auto Select]
[Auto Select]
[Auto Select]
[Auto Select]
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”PCI Configuration” Submenu
5-17
Configuring the SIMATIC Box PC 620
”PCI Devices” Submenu
If the PCI devices field is selected, the following submenu appears:
PhoenixBIOS Setup Utility
Advanced
Item Specific Help
PCI Devices, Slot #1
Option Rom Scan
Enable Master:
Latency Timer
F1
ESC
Figure 5-12
Help
Exit
Select Item
Select Menu
Initialize device expansion
rom
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”PCI Devices, Slot #1” Submenu
[Disabled]
The option ROM of the PCI module (if present) is
enabled
The option ROM of a PCI module is disabled.
Enable Master:
[Enabled]
[Disabled]
This slot can assume the PCI master function
This slot can only operate as a PCI slave.
Latency Timer
[Default]
The number of active PCI clock cycles of the master
modules are determined by the module
With these settings, the maximum active PCI clock
cycles are set to the selected value.
Option ROM
Scan:
[Enabled]
[0020H
to
00E0H]
5-18
[Enabled]
[Enabled]
[0040h]
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Submenu “PCI/PNP ISA IRQ Resource Exclusion”
Available means that the Plug and Play mechanism in BIOS can allocate the IRQ
to Plug and Play submodules or motherboard functions.
Use the ’Reserved’ setting only if the interrupt has to be assigned specifically to
PCMCIA submodules with no Plug and Play capability.
PhoenixBIOS Setup Utility
Advanced
PCI/PNP ISA IRQ Resource Exclusion
IRQ 3:
IRQ 4:
IRQ 5:
IRQ 9:
IRQ 10:
IRQ 11:
F1
ESC
Figure 5-13
SIMATIC Box PC 620 Manual
A5E00131465-01
[ Available ]
[Available]
[Available]
[Available]
[Available]
[Reserved]
Help
Exit
Select Item
Select Menu
Item Specific Help
Reserves the specified
IRQ for use by legacy
ISA devices
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”PCI / PNP ISA IRQ Resource Exclusion” Submenu
5-19
Configuring the SIMATIC Box PC 620
“PCI IRQ line” Field
PhoenixBIOS Setup Utility
Advanced
PCI Configuration
Item Specific Help
PCI Device, Slot #1
PCI Device, Slot #2
Disabled
PCI/PNP ISA IRQ Resource Exclusion
Autoselect
3
PCI IRQ line 1:
4
PCI IRQ line 2:
5
7
PCI IRQ line 3:
9
PCI IRQ line 4:
10
11
12
14
15
F1
ESC
Figure 5-14
5-20
Help
Exit
Select Item
Select Menu
Reserves the specified
IRQ for use by legacy
ISA devices
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
”PCI Configuration” Submenu
Disabled
No interrupt possible for this PCI-IRQ line
AutoSelect
Plug and Play mechanism in BIOS selects unassigned interrupts and
allocates them to the on-board PCI devices.
3 to 15
The PCI-IRQ line is assigned to the selected interrupt.
Do not use this setting unless it is specifically required in your
application’s documentation.
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Submenu “Video Adapter Settings”
PhoenixBIOS Setup Utility
Advanced
Video Adapter Settings
Frame Buffer Size:
AGP Rate:
[8 MB]
[2x]
Default Primary Video Adapter:
[AGP]
F1
ESC
Figure 5-15
Item Specific Help
Help
Exit
Select Item
Select Menu
On board video adapter
buffer size, which is shared with Main Memory
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
Submenu”Video Adapter Settings”
Frame Buffer Size
[8]
[16]
[32]
Specifies the size of the graphic memory used
Onboard graphic card. This range is in the
Main memory of the system.
AGP Rate
[1x]
[2x]
[4x]
Specifies the AGP transfer speed to the Onboard
graphic card.
Default Primary Video
Adapter
[AGP]
The Onboard video graphic card is used as a primary
display unit.
A PCI graphic card may be used as a primary
display device.
This input is ignored if no additional graphic card is
inserted.
SIMATIC Box PC 620 Manual
A5E00131465-01
[PCI]
5-21
Configuring the SIMATIC Box PC 620
5.1.3
The Security Menu
Summary
You can only edit the fields enclosed in square brackets. You can assign two
passwords to protect your PC from unauthorized use. With the supervisor
password, the setup access can be restricted or denied to normal users.
PhoenixBIOS Setup Utility
Advanced
Main
Security
Power
Boot Sequence
Version
Exit
Item Specific Help
Supervisor Password is
User Password is
Disabled
Disabled
Set Supervisor Password
Set User Password
[ Enter ]
[ Enter ]
Password on boot:
[Disabled]
Fixed disk boot sector:
Diskette access:
[Normal]
[Supervisor]
F1
ESC
Help
Exit
Select Item
Select Menu
Figure 5-16
”Security” Menu
Supervisor
Password is
[Disabled]
[Enabled]
Select the operating
system installed
on your system which
you will use most
commonly.
Note: An incorrect
setting can cause
some operating
systems to display
unexpected behavior.
+ / – Change Values
Enter Select Sub-Menu
F9
Setup Defaults
F10 Save and Exit
Password not set. All setup entries can be processed
without a password.
Passwort is enabled. The BIOS setup can only be
processed after entering a password. This password
has a higher priority than a User Password.
The input field automatically changes from [Disabled] to [Enabled] when
the password is entered.
User Password
is
[Disabled]
[Enabled]
No User Password is assigned. If a Supervisor
Password is assigned, only the Supervisor can operate
the setup.
User Password is active. A user is thus given the
right to process some setup fields.
The input field automatically changes from [Disabled] to [Enabled] when
the password is entered.
5-22
Set User
Password
This field opens the dialog box for entering a password. Once it has been
entered correctly, the user password can be changed or deleted by
pressing ”Return” and thus deactivated.
Password on
boot
[Disabled]
No password required for system boot.
[Enabled]
Supervisor or user password must be entered for system
boot.
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Fixed disk boot
Sector
[Normal]
All types of hard-disk access are permitted.
Diskette
access
This mode of protection is not active unless ”Password on boot ” is set to
[enabled].
[Write protect] No operating system can be installed.
This is a way of protecting against boot viruses.
[Supervisor] Diskette access is not possible unless the supervisor
password was entered during system boot.
[User]
SIMATIC Box PC 620 Manual
A5E00131465-01
Diskette access is not possible unless the user password
was entered during system boot.
Note:
This function can not be used under WIndows NT/2000,
since this operating system does not access the diskette
via BIOS routines. Please use the Windows NT/2000
system programs for this purpose.
5-23
Configuring the SIMATIC Box PC 620
5.1.4
The Power Menu
Summary
This menu has the following structure.
PhoenixBIOS Setup Utility
Main
Security
Advanced
APM:
Power
Power Savings:
[Enabled]
[Disabled ]
Standby Timeout:
Off
Hard Disk Timeout:
Boot Sequence
Version
Exit
Item Specific Help
APM (Advanced Power
Management) allows APM
aware software to manage
power savings, if enabled
[Disabled]
Disabled
Customized
Maximum Power Savings
Maximum Performance
Not valid for ACPI
Operating Systems
F1
ESC
Figure 5-17
Help
Exit
Select Item
Select Menu
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
“Power” Menu
The Power menu offers a number of power saver modes for environmentally
friendly computing:
5-24
APM
(Advanced
Power
Management)
[Enabled]
Power Savings
[Disabled]
No power-saving functions[Customize, Maximum
Power Savings, Maximum Performance]
User-selectable and preset power saving functions
for maximum and minimum power saving.
You can set the parameters for Standby/Suspend
Timeouts and Fixed Disk Timeout or they set
automatically to their defaults.
Standby
Timeout
[Off]
[30 seconds or
1, 2, 4, 8, 12, 16]
No standby mode
...minutes after your PC enters standby mode.
Hard Disk
Timeout
[Disabled]
[10, 15, 30, 60]
The hard disk does not shut down.
Time since the last hard-disk access, the hard disk
is shut down.
The next time it is accessed, the hard disk starts
spinning again after a brief delay.
[Disabled]
The operating system can shut down system
resources when they are not needed.
The operating system is denied APM access.
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
5.1.5
The Boot Sequence Menu
Summary
This menu allows you to prioritize the boot devices.
PhoenixBIOS Setup Utility
Main
Advanced
Security
Power
Boot Sequence
Version
Exit
Item Specific Help
+ Removable Device
+ Hard Drive
ATAPI CD-ROM Drive
F1
ESC
Figure 5-18
Help
Exit
Select Item
Select Menu
Keys used to view or
configure devices:
<Enter> expands or
collapses devices with
a + or –
<Ctrl+Enter> expands
all
<+> and <–> moves
the device up or down.
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
“Boot Sequence” Menu
This menu lists the boot devices in groups. The group with the highest priority is at
the top. The procedure for changing the sequence is as follows:
Use the ↑↓+keys to select a group and the + or – keys to move the group to its
new position in the sequence.
Note
During booting the boot drive can be selected with the ESC key.
SIMATIC Box PC 620 Manual
A5E00131465-01
5-25
Configuring the SIMATIC Box PC 620
Groups marked + can contain more than one device. When you select a group
marked in this way, hit Enter to view the list of devices in the group. See the figure
below for an illustration:
PhoenixBIOS Setup Utility
Main
Advanced
Security
Power
Legacy Floppy Drive
–Hard Drive
FUJITSU MPF3204AT-(PM)
Alternate Device
CD-ROM Drive
Figure 5-19
Help
Exit
Select Item
Select Menu
Version
Exit
Item Specific Help
–Removable Devices
F1
ESC
Boot Sequence
Keys used to view or
configure devices:
<Enter> expands or
collapses devices with
a + or –
<Ctrl+Enter> expands
all
<+> and <–> moves
the device up or down.
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
“Boot Sequence” Menu (Example)
This screen shows all possible boot devices; within a given group the highest
priority device is always listed first. Here again, you can change the sequence as
described above.
If a boot device is not available, the next device in the sequence is automatically
checked to ascertain whether or not it is bootable.
5-26
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
5.1.6
The Version Menu
This menu contains the information you will have to quote when you send us
technical questions about your system.
PhoenixBIOS Setup Utility
Main
Advanced
Security
Power
Boot Sequence
Version
Exit
Item Specific Help
SIMATIC
Box PC 620
Bios Version
Bios Number
V02.01.02
A5E00123801–ES0x
Board Revision
V01
MPI/DP Firmware
Ethernet Config Version
V01
V01
CPU Type
CPU Speed
CPU ID
Code Revision
Pentium(R) III
866 MHz
0683
0014
F1
ESC
Figure 5-20
SIMATIC Box PC 620 Manual
A5E00131465-01
Help
Exit
Select Item
Select Menu
If any items require
changes, please consult
your system Supervisor.
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
“Version” Menu
5-27
Configuring the SIMATIC Box PC 620
5.1.7
The Exit Menu
The Exit Menu
The setup program is always terminated using this menu.
PhoenixBIOS Setup Utility
Main
Advanced
Security
Power
Version
Boot Sequence
Exit
Item Specific Help
Exit Saving Changes
Exit Discarding Changes
Setup Defaults
Load Discard Changes
Save Changes
F1
ESC
Figure 5-21
Help
Exit
Select Item
Select Menu
Exit System Setup and
save your change to
CMOS.
+ / – Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Menü “Exit”
Save Changes
& Exit
All changes are saved; a system restart is carried out with the new
parameters.
Discard
All changes are rejected; a system restart is carried out with the old
Changes & Exit parameters.
5-28
Get Default
Values
All parameters are set to safe values.
Load Previous
Values
The last saved values are reloaded.
Save Changes
Save all Setup settings.
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
5.1.8
Default Setup Settings
Documenting Your Device Configuration
If you have made any modifications to the default Setup settings, you can enter
them in the following table. You can then refer to these entries if you need to make
any hardware modifications later.
Note
Print the following table out and keep the pages in a safe place once you have
filled in your entries.
Systemparameter
Main
System Time
System Date
Diskette A
Default Settings
Primary Master
Primary Slave
Secondary Master
Secondary Slave
hh:mm:ss
MM/TT/JJJJ
1,44 MB, 3 1/2”
bei LS 240: Disabled
C: 20496 MB
None
CD–ROM
None
Memory Cache
Write back
Boot Options
Quick Boot Mode
SETUP prompt
POST Errors
Floppy check
Summary screen
Enabled
Enabled
Enabled
Disabled
Enabled
Keyboard Features
Num Lock
Key Click
Keyboard auto-repeat rate:
Keyboard auto-repeat delay
On
Disabled
30/s
1/2s
Hardware Options
PCI-MPI/DP:
On Board Ethernet
Ethernet Adress
LAN remote boot
Cardbus/PCMCIA Slot
SafeCard Functions
Legacy USB Support
Enabled
Enabled
08000624xxxx
Disabled
Enabled
Enabled
Disabled
SIMATIC Box PC 620 Manual
A5E00131465-01
YourEntries
5-29
Configuring the SIMATIC Box PC 620
Systemparameter
Fan Control
CRT/LCD selection
LCD Screensize
DSTN Contrast
PS2 Mouse
Advanced
COM/LPT Configuration
Internal COM1
Base I/O address
Interupt
Internal COM2
Base I/O address
Interrupt
Internal LPT1
Mode
Base I/O address
Interrupt
DMA Channel (nur bei ECP)
PCI-Configuration
PCI Device Slot 1
Option ROM Scan
Enable Master
Latency timer
PCI Device Slot 2
Option ROM Scan
Enable Master
Latency timer
PCI/PnP ISA IRQ Exclusuion
IRQ3
IRQ4
IRQ5
IRQ9
IRQ10
IRQ11
Default Settings
Enabled
SIMULTAN
Expanded
154
Enabled
Enabled
3F8
IRQ4
Enabled
2F8
IRQ3
Enabled
Bi-directional
378
IRQ7
DMA 3
Enabled
Enabled
0040 h
Enabled
Enabled
0040 h
Available
Available
Available
Available
Available
Reserved
PCI IRQ Line 1
PCI IRQ Line 2
PCI IRQ Line 3
PCI IRQ Line 4
Auto Select
Auto Select
Auto Select
Auto Select
Installed O/S
Reset Configuration Data
Floppy disk controller
Local Bus IDE adapter
Large Disk Access Mode
Hard Disk Pre-Delay
Memory Gap at 15 Mbyte
Other
No
Enabled
Both
DOS
Disabled
Disabled
5-30
YourEntries
SIMATIC Box PC 620 Manual
A5E00131465-01
Configuring the SIMATIC Box PC 620
Systemparameter
Video Adapter Settings
Frame Buffer Size
AGP Rate
Default Primary Video Adapter
Default Settings
8 MB
2x
AGP
Security
Supervisor Password Is
User Password Is
Set Supervisor Password
Set User Password
Password on boot
Fixed disk boot sector
Diskette Access
Disabled
Disabled
Enter
Enter
Disabled
Normal
Supervisor
Power
APM
Power Savings
Standby Timeout
Hard Disk Timeout
Fan Control
Enabled
Disabled
off
Disabled
Enabled
YourEntries
Boot Sequence
Diskette Drive
Removable Devices
Hard Drive
ATAPI CD-ROM Drive
Version
SIMATIC
BIOS Version
Board Revision
BIOS Number
MPI/DP Firmware
Ethernet Config Version
CPU Type
CPU Speed
Code Revision
SIMATIC Box PC 620 Manual
A5E00131465-01
Box PC 620
V7.xx
V01
A5E16562-ESxx
V01
V01
Pentium III
866 MHz
001A
5-31
Configuring the SIMATIC Box PC 620
5.2
Configuring the PC Card
You can obtain the software you require for using PC cards under MS DOS, such
as
S
Socket Services
S
Card Services
S
Client Drivers
S
Flash File System
from the nearest Siemens sales office or representative.
Your PC comes supplied with Windows 98 / NT4 / 2000 already installed; this supports the PC Card interface.
After configuration, the computer must be rebooted.
5-32
SIMATIC Box PC 620 Manual
A5E00131465-01
6
Error Diagnosis
Overview of Chapter
In chapter
you will find
on page
6.1
Problems When Using Modules from Other Manufacturers
6-2
6.2
The Monitor Remains Dark
6-3
6.3
The Screen Display Does not Appear or Drifts
6-4
6.4
No Mouse Pointer Appears on the Screen
6-4
6.5
The Clock Time and/or the Date in Your PC Is Incorrect
6-5
6.6
USB-Device does not function
6-5
6.7
An Error Message Appears on the Screen
6-6
6.8
Diagnostic Messages (Port 80)
6-8
SIMATIC Box PC 620 Manual
A5E00131465-01
6-1
Error Diagnosis
6.1
Problems When Using Modules from Other Manufacturers
Error Display
The PC crashes during power up.
Cause
The following causes are possible:
– Double assignment of I/O addresses
– Double assignment of hardware interrupts and/or DMA channels
– Signal frequencies or signal levels are not met
– Different connector assignments
Remedy
Check your computer configuration:
If the computer configuration is the same as when your PC was delivered,
please contact your technical support team (Chapter 8).
If the computer configuration has changed, re-establish the configuration you
had when your PC was delivered. Remove any modules from other manufacturers. Perform a complete restart on your PC.
– If the PC still crashes, you must contact your technical support team.
– If the error no longer occurs, the module you used from another manufacturer was the cause of the fault. Replace this module with a Siemens module,
or contact the module supplier.
6-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Error Diagnosis
6.2
The Monitor Remains Dark
Cause and Remedy
The following causes are possible:
The monitor has been switched off.
Switch on the monitor.
The monitor is in “powersave” mode.
Press any key on the keyboard.
The brightness button has been set to dark.
Set the screen’s brightness button to obtain more light. Refer to the operator’s
guide for the monitor for more detailed information.
The power supply cable or the screen cable is not connected.
Switch off the monitor and the system unit.
Check whether the power supply cable has been connected correctly to the monitor and to the system unit or to the grounding outlet.
Check whether the monitor cable has been connected correctly to the system
unit and to the screen (if a connector is present).
Switch on the monitor and the system unit.
Note
If the monitor screen still remains dark after these checks and measures have
been carried out, please contact your technical support team.
SIMATIC Box PC 620 Manual
A5E00131465-01
6-3
Error Diagnosis
6.3
The Screen Display Does not Appear or Drifts
Cause and Remedy
Either the incorrect line frequency and/or the incorrect resolution is set for the
screen or for the user program.
6.4
Stop the user program. If the error still occurs after you have ended the program, switch off the monitor. After at least three seconds, switch on the monitor
again.
Adjust the relevant entries for the monitor in the CONFIG.SYS file (on the hard
drive).
Correct the settings for the monitor and graphics in your user program.
Select the correct screen driver for your user program.
No Mouse Pointer Appears on the Screen
Cause and Remedy
The mouse pointer may not appear for the following reasons:
The mouse driver is not loaded
Check whether the mouse driver is correctly installed. Check whether the
mouse pointer is present when you start your user program. Refer to the manuals for the mouse and user program to obtain detailed information about the
mouse driver.
The mouse is not connected
Switch off your PC.
Check whether the mouse cable is connected to the system unit correctly. If
you use an adapter or an extension cord for the mouse cable, also check their
plug-in connections.
Switch on your PC.
Note
If the mouse pointer still does not appear on the screen after you have performed
these checks and measures, please contact your technical support team.
6-4
SIMATIC Box PC 620 Manual
A5E00131465-01
Error Diagnosis
6.5
The Clock Time and/or the Date in Your PC Is Incorrect
Remedy
Set the clock time and the date in the setup menu.
Press <F2> to call setup when booting the computer.
Note
The battery is dead if the clock time and the date are still incorrect after you switch
off your PC and switch it back on again. In this case, please contact your technical
support team.
6.6
USB-Device does not function
The USB port is not recognized by the operating system. It is only supported by
Windows Me, Windows 2000 and Windows XP at the present time. In addition, the
BIOS setup can be controlled by a USB keyboard.
SIMATIC Box PC 620 Manual
A5E00131465-01
6-5
Error Diagnosis
6.7
An Error Message Appears on the Screen
Error Messages
The following table describes the error messages that the BIOS system outputs.
Error messages the operating system or program outputs are described in the
manuals for these programs.
Press <F2> to call Setup when booting the computer.
Error Message on the Screen
Meaning/Suggestion
Address conflict
Plug and Play Problem
Contact your technical support team.
Combination not supported
Plug and Play Problem
Contact your technical support team
IO device IRQ conflict
Plug and Play Problem
Contact your technical support team
Invalid System Configuration
Data
Plug and Play Problem
Please set the option RESET CONFIGURATION.DATA in the
Advanced Setup menu.
Contact your technical support team
Allocation Error for ...
Plug and Play Problem
Please undo the last hardware change.
Contact your technical support team
System battery is dead
Replace and run SETUP
The battery on the CPU module is defective or dead.
Contact your technical support team
System CMOS checksum bad
Run SETUP
Call up SETUP, adjust settings and save. If this message appears
during each power up, contact your technical support team.
Incorrect Drive A type
Run SETUP
Check the SETUP entries for drive A.
Incorrect Drive B type
Run SETUP
Check the SETUP entries for drive B.
Diskette drive A error
Error accessing drive A.
Contact your technical support team.
Diskette drive B error
Error accessing drive B.
Contact your technical support team.
Failure Fixed Disk
Error accessing the hard drive.
Check the SETUP settings
Contact your technical support team.
Keyboard error
Check whether the keyboard is connected correctly.
Stuck Key
Check whether a key on the keyboard is stuck.
System RAM Failed at offset:
Memory error
Contact your technical support team.
Shadow RAM Failed at offset:
Memory error
Contact your technical support team
Extended RAM Failed at offset:
Memory error
Contact your technical support team
Failing Bits:
Memory error
Contact your technical support team
6-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Error Diagnosis
Error Message on the Screen
Meaning/Suggestion
Operating system not found
Possible causes:
No operating system present
Incorrect drive addressed (diskette in drive A/B)
Incorrect active boot partition
Incorrect entries in SETUP for the BOOT drive
Previous boot incomplete
Default configuration used
Abort of the previous BOOT procedure, for example, due to a power
failure. Check the hardware settings and the SETUP.
System cache error
Cache disabled
Error in the CPU’s cache module.
Contact your technical support team.
Monitor type does not match
CMOS
Run SETUP
The monitor does not match the SETUP entries.
Adapt the SETUP entries to the monitor.
System timer error
Hardware error
Contact your technical support team.
Real time clock error
Clock chip error
Contact your technical support team.
Keyboard controller error
Keyboard error
Contact your technical support team.
SIMATIC Box PC 620 Manual
A5E00131465-01
6-7
Error Diagnosis
6.8
Diagnostic Messages (Port 80)
When the SIMATIC PC is powered up, it runs a self-test (POST = Power On
Self-Test). If the POST detects a fault, it outputs the sequence of beeps (beep
code) assigned for the fault. Each beep code consists of 2 x 2 sequences.
In addition, the individual self-test steps are output at I/O port 80h.
Conversion table for the beep codes to hexadecimal representation:
Beeps
Hex-Code
B
B
B
BB
0
1
B
BBB
2
B
BB
BBBB
B
3
4
BB
BB
5
BB
BBB
6
BB
BBB
BBBB
B
7
8
BBB
BB
9
BBB
BBB
A
BBB
BBBB
BBBB
B
B
C
BBBB
BB
D
BBBB
BBBB
BBB
BBBB
E
F
Example:
B
BBB
2
BBB
B
8
Check system memory
Beeps
Hexadecimal code
Meaning
Special codes
In addition to the subsequent beep codes listed, there are the following special
codes:
6-8
3x short
If the INSERT button is pressed during system start:
the Onboard Device Installation is skipped. The Onboard
Graphics is used as standard output.
1x long 8x short
Error occurs when reading the MPI system information:
please turn to your customer support.
4x short
MPI EPROM is programmed for the first time.
1x long 5 x short
Ethernet Error: please turn to your customer support.
SIMATIC Box PC 620 Manual
A5E00131465-01
Error Diagnosis
The POST codes in order of occurrence:
Display
(hex)
Meaning
Description
02
TP_VERIFY_REAL
Test whether the CPU is in real mode
1C
TP_RESET_PIC
Reset the interrupt controller
12
TP_RESTORE_CRO
Restore the controller register
13
TP_PCI_BM_RESET
Reset the PCI bus master
36
TP_CHK_SUTDOWN
Check the shutdown code
24
TP_SET_HUGE_ES
Switch the ES to special mode
03
TP_DISABLE_NMI
Switch off the NMI
0A
TP_CPU_INIT
Initialize the CPU
04
TP_GET_CPU_TYPE
Determine the CPU type
AE
TP_CLEAR_BOOT
Edit the boot flag
06
TP_HW_INIT
Initialize the main hardware
18
TP_TIMER_INIT
Initialize the timer
08
TP_CS_INIT
Initialize the chip set
C4
TP_PEM_SIZER_INIT
Reset system error
0E
TP_IO_INIT
Initialize IO
0C
TP_CACHE_INIT
Initialize the cache
16
TP_CHECKSUM
EPROM checksum test
28
TP_SIZE_RAM
Determine the RAM size
3A
TP_CACHE_AUTO
Determine the cache size
2A
TP_ZERO_BASE
Set 512k base RAM to 0
2C
TP_ADDR_TEST
Test the base RAM address cables
2E
TP_BASERAML
Check the 1.64k base RAM
0A
TP_CPU_INIT
Initialize the CPU
38
TP_SYS_SHADOW
BIOS-shadow
0B
TP_CPU_CACHE_ON
Switch on the cache
0F
TP_FDISK_INIT
Initialize the hard disk
10
TP_PM_INIT
Initialize the power management
14
TP_8742_INIT
Initialize the 8742 circuit
1A
TP_DMA_INIT
Initialize the DMA circuits
1C
TP_RESET_PIC
Reset the interrupt controller
32
TP_COMPUTE_SPEED
Determine the clock pulse speed
C1
TP_740_INIT
Initialize the PG 740 I/Os
34
TP_CMOS_TEST
Test the CMOS RAM
3C
TP_ADV_CS_CONFIG
Configure the advanced chip set
42
TP_VECTOR_INIT
Initialize the interrupt vectors
46
TP_COPYRIGHT
Test the copyright
SIMATIC Box PC 620 Manual
A5E00131465-01
6-9
Error Diagnosis
Display
(hex)
Meaning
Description
49
TP_PCI_INIT
Initialize the PCI interface
48
TP_CONFIG
Check the configuration
4A
TP_VIDEO
Initialize the video interface
4C
TP_VID_SHADOW
Copy the video BIOS to RAM
24
TP_SET_HUGE_ES
Switch the ES to special mode
22
TP_8742_TEST
Test circuit 8742
52
TP_KB_TEST
Keyboard available?
54
TP_KEY_CLICK
Switch the keyboard click on/off
76
TP_KEYBOARD
Check the keyboard
58
TP_HOT_INT
Test for unexpected interrupts
4B
TP_QUIETBOOT_START
Switch off any boot messages
4E
TP_CR_DISPLAY
Display the copyright notice
50
TP_CPU_DISPLAY
Display the CPU type
5A
TP_DISPLAY_F2
Display the F2 message for “SETUP”
5B
TP_CPU_CACHE_OFF
Switch off the cache if applicable (SETUP
setting)
5C
TP_MEMORY_TEST
Test the system memory
60
TP_EXT_MEMORY
Test the extended memory
62
TP_EXT_ADDR
Test the A20 address line
64
TP_USERPATCH1
Area for own initializations
66
TP_CACHE_ADVNCD
Determine and enable the cache size
68
TP_CACHE_CONFIG
Configure and test the cache
6A
TP_DISP_CACHE
Display the cache configuration
6C
TP_DISP_SHADOWS
Configuration and size of the shadow
Display RAM
6-10
6E
TP_DISP_NONDISP
Display non-disposable segment
70
TP_ERROR_MSGS
Display post error
72
TP_TEST_CONFIG
Check SETUP irregularities
7C
TP_HW_INTS
Set the IRQ vectors
7E
TP_COPROC
Check whether the CO processor is
present
96
TP_CLEAR_HUGE_ES
Switch the ES back
80
TP_IO_BEFORE
Disable IO circuits
88
TP_BIOS_INIT
Various initialisations
8A
TP_INIT_EXT_BDA
Initialize the external BIOS data area
85
TP_PCI_PCC
Determine the PCI circuits
82
TP_RS232
Determine the serial interfaces
84
TP_LPT
Determine the parallel interface
SIMATIC Box PC 620 Manual
A5E00131465-01
Error Diagnosis
Display
(hex)
Meaning
Description
86
TP_IO_AFTER
Re-enable the IO circuits
83
TP_FDISK_CFG_IDE_CTRLR
Configure the IDE controller
89
TP_ENABLE_NMI
Enable the NMI
8C
TP_FLOPPY
Initialize the floppy controller
90
TP_FDISK
Initialize the hard disk controller
8B
TP_MOUSE
Test the internal mouse interface
95
TP_CD
Test the CP
92
TP_USERPATCH2
Area for own initializations
98
TP_ROM_SCAN
Search for BIOS expansions
69
TP_PM_SETUP
Initialize the power management
9E
TP_IRQS
Enable the hardware IRQ
A0
TP_TIME_OF_DAY
Set the clock time and date
A2
TP_KEYLOCK_TEST
Preset the keylock
C2
TP_PEM_LOCK
Stop the error manager
C3
TP_PEM_DISPLAY
Display any possible errors
A8
TP_ERASE_F2
Delete the F2 message
AA
TP_SCAN_FOR_F2
Was F2 printed?
AC
TP_SETUP_CHEK
Output any F1/F2 message
AE
TP_CLEAR_BOOT
Cancel the self-test flag
B0
TP_ERROR_CHECK
Check for any possible errors
B2
TP_POST_DONE
End of the self-test
BE
TP_CLEAR_SCREEN
Clear the screen
B6
TP_PASSWORD
Password query (option)
BC
TP_PARITY
Cancel the parity memory bit
BD
TP_BOOT_MENU
Display the boot menu (option)
B9
TP_PREPARE_BOOT
Prepare the boot
C0
TP_INT19
Boot via Interrupt 19
00
SIMATIC Box PC 620 Manual
A5E00131465-01
Message after startup is complete
6-11
Error Diagnosis
6-12
SIMATIC Box PC 620 Manual
A5E00131465-01
7
Hardware Information
Overview of Chapter
In chapter
you will find
on page
7.1
Current Requirement of the Components (Maximum Values)
7-2
7.2
Overview of the Components and Ports
7-3
7.3
System Resources
7-4
7.4
Monitoring Functions
7-5
7.5
Ports
7-9
7.6
Bus Unit
7-31
7.7
Power Supply Unit with 85W Leistungsabgabe (AC and DC)
7-36
7.8
Power Supply Unit with 105W Leistungsabgabe (AC and DC)
7-37
7.9
Connecting Cables
7-38
SIMATIC Box PC 620 Manual
A5E00131465-01
7-1
Hardware Information
7.1
Current Requirement of the Components (Maximum Values)
Basic System with Power Supply Unit 85W
Component
Voltage
+5V
Pentium III Motherboard
0.5 A
Processor Pentium III 1260
5A
Floppy disk drive / LS 240
0.56 A
Hard disk
0.4 A
CD RW/DVD drive
0.92 A
+3.3V
2.5 A
+12V
–5V
0.1 A
–12V
0.02 A
0.5 A
Fan
0.2 A
Sum (basic configuration)
7.38 A
ISA/PCI slots (Sum)
3A
2.5 A
0.8 A
0A
0.02 A
0.6 A
0.1 A
0.1 A
PC-Card slot
0.5 1
0.6 A 1
0.12 A
Sum (max. for maximum
configuration)
10 A 2
4.2 A
1.7 A 3
0.1 A
0.2 A
Total power consumption
85W
Basic System with Power Supply Unit 105W
Component
Voltage
+5V
Pentium III Motherboard
0.5 A
Processor Pentium III 1260
5A
Floppy disk drive / LS 240
0.56 A
Hard disk
0.4 A
CD RW/DVD drive
0.92 A
+3.3V
2.5 A
+12V
–5V
0.1 A
–12V
0.02 A
0.5 A
Fan
0.2 A
Sum (basic configuration)
7.38 A
2.5 A
0.8 A
0A
0.02 A
ISA/PCI slots (Sum)
3A
4A
0.6 A
0.1 A
0.1 A
PC-Card slot
0.5 1
0.6 A 1
0.12 A
Sum (max. for maximum
configuration)
13.5 A 2 8.5 A
0.1 A
0.3 A
Total power consumption
105W
1
2
3
4
5
6
7-2
2.5 A 3
Alternative 5V or 3.3V
11A, if the total power consumption is not exceeded
3A, if the total power consumption is not exceeded
15A for 5 sec.
4A for 5 sec
are generated on the Bus board from -12V
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
7.2
Overview of the Components and Ports
Component/Port
Description
Parameters
Chipset
VIA PN133T
SDRAM
BIOS
Update via software
512K in 4 pages
CPU
Pentium III / Celeron (type FC-PGA370)
Upgradeable
Multimedia support
On Board L2-Cache with 128 k/256 k
/512 K
Memory
Graphics
DIMM modules
up to max. 256MB/DIMM
UXGA LCD Controller on the AG Bus is
integrated Chip set (S3)
Data capacity of 64 bits + ECC
66/100MHz bus speed
Modules with ECC possible
3.3 V
SDRAM to PC100 specification
up to 128MBit chip size on the
module
2 DIMMs can be used
easy to exchange
variable from 64-512MB/DIMM
up to 32 Mbytes of SDRAM are part
of the main memory and can be
configured (8/16/32MB)
CRT:
up to1600x1200/85Hz 65536 colors
with PC133 memory modules
up to1280x1024/85Hz 65536 colors
with PC100 memory modules
Hard Disk
ATA-33 mode
CD ROM
Master on secondary EIDE port
Ultra DMA capable
24 speed
CD RW/DVD
Master on secondary EIDE port
Multi Spin Writer Drive
Read: CD ROM, CD R 14-32 times,
CD RW 8-20 times Speed, 8 times
Write: CD R 12 times,
CD RW 10 times Speed
suppors recording:
Disc at once, Track at once,
Session at once, Packet writing
Floppy
Notebook port for 34 pin flat cable
1.44 MB
LS240
Slave on secondary EIDE port
Keyboard
Port for PS2 keyboard
Mouse
PS2 mouse port
Serial
COM1/25 pins
COM2/9 pins.
TTY *2
Communication with SIMATIC S5-CPUs
SIMATIC Box PC 620 Manual
A5E00131465-01
1.44MB standard floppy disks
120MB/240MB SuperDisk
Standard
Standard
TTY *2 and V24
Standard
Range up to 1000 m
7-3
Hardware Information
Component/Port
Parallel
DP12
*2
Description
Parameters
Standard, bidirectional, EPP and
ECP mode
25 pin subminiature Cannon
Communication port
SIMATIC S7
potentially isolated DP12 *1
connector
(CP 5611 compatible)
12MBaud
USB
Universal Serial Bus
three high current (500mA) USB
Ethernet
10BaseT/100Base-TX (Intel 82559)
10/100 Mbps, potentially isolated *1
*1
*2
7.3
ports
(2x external and 1x internal)
Electrically isolated in a safety extra-low voltage circuit (SELV)
Optional product feature
System Resources
All system resources (hardware address, memory configuration, IRQ,
DMA channel) are assigned dynamically by the Windows OS, depending on the
hardware configuration, drivers and connected peripheral devices. You can view
the current configuration of system resources or possible conflicts with the
following operating systems:
Windows 98
Start > Programs > Accessories > System Tools > System Information
Windows 2000
Start > Settings > Control Panel > Administrative Tools > Computer Management > System Information
Windows NT 4.0
Start > Programs > Administrative Tools (Common) > Windows NT
Diagnostics
7-4
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
7.4
Monitoring functions
The LEDs described in the following passages exist only for specific device
models. The basic model of the Box PC 620 has no LEDs. The hardware signals
are described in Section 7.5.2.
7.4.1
Overview
Function
The following individual functions are implemented:
Temperature monitoring and excess/insufficient temperature indication
Watchdog
Monitoring the processor fan
Messages from the monitoring modules can be transferred to applications.
The program SOM (Safecard On Motherboard) as well as drivers for Windows are
available on the units for this. The status can be displayed or limits parameterized
thereby.
You will find a description of the drivers and the SOM program on the
Documentation and Drivers CD in the \Drivers.*\Safeonbo.ard directory.
7.4.2
Signals on the Front Interface
The meaning of the indicators is as follows:
LED
OFF
Watchdog
Watchdog not
active
Temp
Inside temperature
normal
SIMATIC Box PC 620 Manual
A5E00131465-01
GREEN
Watchdog active
RED
Watchdog executed
Inside temperature
outside the permissible
range.
7-5
Hardware Information
7.4.3
Temperature Monitoring/Indication
Temperature Monitoring
The temperature is measured by means of three temperature sensors. One sensor
monitors the processor temperature, the second the temperature in the area of the
memory module and the expansion cards and the third the temperature in the area
of the power supply unit.
If the temperature near the power supply exceeds 45oC (fixed value), the fan is
set to maximum rpms. To activate this feature, the setting “Fan Control” has to
be turned on in the Setup menu (Sec. 6.1.4).
If the temperature exceeds one of the three temperature values of the set thresholds, a temperature error is registered with the following effects:
Reaction
Option
Temp LED to red
always
Fan goes to maximum rpms.
always
SOM application is displayed
always
Temperature errors do not occur during the normal approved use of the device. If a
temperature error occurs, check the following possible causes:
Are the ventilation slots blocked?
Is the fan working?
Is the ambient temperature higher than the allowed value?
Has the total capacity for the power supply been exceeded?
The temperature error remains saved until the temperature thresholds are again
exceeded and are reset by one of the following measures:
7-6
Acknowledge the error message via the SOM program
Restarting the device.
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
7.4.4
Watchdog (WD)
Function
The watchdog monitors the execution of a program. The purpose of the WD is to
notify the user of a program crash through various reactions.
The watchdog is idle when the PC is switched on or after a HW-RESET(cold start),
i.e. no reaction of the WD will be triggered and the RUN LED is switched off. If the
watchdog is activated (by driver or SOM program) the Run LED is green.
WD Reactions
If the WD is not triggered again within the set time (by driver or SOM program), the
following reactions are initiated:
Reaction
Option
Watchdog LED switches from green to red
always
Acknowledge WD
always
Initiate reset of the PC
adjustable
SOM application is displayed
always
The reactions which are to be triggered can be parameterized by driver or
SOM program.
WD Monitoring Times TWD
The monitoring times are adjustable in increments of one second in a range from
3 to 255 seconds.
Note
If the watchdog time is changed after the watchdog was activated (i.e., while the
watchdog is running), the watchdog is retriggered!
SIMATIC Box PC 620 Manual
A5E00131465-01
7-7
Hardware Information
7.4.5
Fan Monitoring
Processor fan operation is monitored. If the fan should fail, the following reactions
are triggered:
Reaction
Option
SOM application is displayed
always
The temperature error remains stored until the cause of the fan failure has been
corrected in one of the following ways:
7-8
Acknowledgement of the error message via the SOM program.
Device restart.
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
7.5
Ports
The following ports are available on the motherboard of the Box PC 620:
External ports for the connection of external devices
Interfaces for the connection of display devices
Ports for internal connections (drives, bus boards etc.)
The connector assignments of the individual ports are described in the following
chapters.
7.5.1
External Ports
Port
Position
Connector
COM1
external
X9
3F8h-3FFh, can be disabled
IRQ4, edge-triggered
25 pin, socket, V.24/V.28 and
20mA (TTY potentially isolated)
COM2
external
X11
2F8h-2FFh, can be disabled
IRQ3, edge-triggered
9 pin, standard connector
LPT1
external
X9
378h-37Fh, can be disabled
IRQ7, edge-triggered
25 pin, standard socket
PS/2 mouse
external
X6
060h-064h
IRQ12, edge-triggered
6 pin, mini DIN socket
PS/2 keyboard
external
X6
060h-064h
IRQ1, edge-triggered
6 pin, mini DIN socket
USB
external
X40
First USB channel, additional internal
second USB channel for front interface
MPI /DP12
external
X600
can be disabled
IRQ5, edge-triggered
9 pin, standard socket, potentially isolated
port
Ethernet
external
X500
RJ45
VGA
external
X11
PCCard/CardBus
port
external
X700
SIMATIC Box PC 620 Manual
A5E00131465-01
Description
3B0h-3BFh, 3C0h-3CFh, 3D0h-3DFh, can
be disabled
IRQ9, edge-triggered
15 pin, standard socket
3E0h-3E1h
100 pin SMD plinth
7-9
Hardware Information
Serial Port COM1 (PLC/V.24/Modem) *
The serial port (COM 1) on the Box PC has the following pinout:
1
13
14
25
Figure 7-1 COM 1 Serial Port (Socket Connector)
Pin No.
Designation
Description
Input /Output
1
-
Shield
-
2
TxD (D1)
Serial transmit data
Output
3
RxD (D2)
Serial receive data
Input
4
RTS (S2)
Request to send
Output
5
CTS (M2)
Clear to send
Input
6
DSR (M1)
Data set ready
Input
7
GND (E2)
Functional ground
(reference potential)
-
8
DCD (M5)
Data carrier detect
Input
9
+TTY RxD
TTY receive
Input
10 - 17
-
Unassigned
-
18
+TTY TxD
TTY send
Output
19
+20mA
Isolated current source
-
20
DTR (S1)
Data terminal ready
Output
21
-TTY TxD
TTY send
Output
22
RI (M3)
Incoming call
Input
23-25
-
Unassigned
-
*
7-10
The line current (TTY) interface is an optional product feature.
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Gender Changer for COM1
You can convert the COM1/V24 / AG port of the SIMATIC PC family into the usual
25 pin male connector by means of the enclosed gender changer (25 pin / 25 pin).
For this, you only have to plug the gender changer onto the COM1 socket and
secure it with the two hexagon head screws.
The V24 and TTY interfaces for COM1 can be alternately used. The factory set
default value is V24 operation. Switching from V24 to TTY operation is described in
Section 5.1.2.
Serial Port COM2 (V24/Mouse)
The serial port (COM 2) on the Box PC has the following pinout:
5 9
1
6
Figure 7-2 Serial Port COM 2 (Connector)
Pin No.
Designation
Description
Input / Output
1
DCD (M5)
Receiving signal level
carrier
Input
2
RxD (D2)
Received data
Input
3
TxD (D1)
Transmitted data
Output
4
DTR (S1)
Terminal ready
Output
5
GND (E2)
Functional ground
(reference potential)
-
6
DSR (M1)
Readiness for operation
Input
7
RTS (S2)
Switch on transmitter
Output
8
CTS (M2)
Ready to transmit status
Input
9
RI (M3)
Incoming call
Input
SIMATIC Box PC 620 Manual
A5E00131465-01
7-11
Hardware Information
Parallel Port LPT1
The parallel port (LPT 1) on the Box PC has the following pinout:
1
13
14
25
Figure 7-3 Parallel Port LPT 1 (Socket)
7-12
Pin No.
Designation
Description
Input / Output
1
/ Strobe (CLK)
Data message
Output (open collector)
2
Data - Bit 0
Data line 0
Output (TTL level)
3
Data - Bit 1
Data line 1
Output (TTL level)
4
Data - Bit 2
Data line 2
Output (TTL level)
5
Data - Bit 3
Data line 3
Output (TTL level)
6
Data - Bit 4
Data line 4
Output (TTL level)
7
Data - Bit 5
Data line 5
Output (TTL level)
8
Data - Bit 6
Data line 6
Output (TTL level)
9
Data - Bit 7
Data line 7
Output (TTL level)
10
/ACK
Acknowledge
Input (4.7 kW pull up)
11
BUSY
Not ready
Input (4.7 kW pull up)
12
PE
No paper
Input (4.7 kW pull up)
13
SELECT
Device selection
Input (4,7 kW pull up)
14
/ AUTO FEED
Automatic new line
Output (open collector)
15
/ ERROR
Device error
Input (4,7 kW pull up)
16
/ INIT
Reset / Initialization
Output (open collector)
17
/ SELECT IN
Printer selection
Output (open collector)
18 - 25
GND
Ground
-
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
PS/2 Mouse Port
You can connect an external PS/2 mouse to your Box PC. The connector has the
following pinout:
6
5
4
3
2
1
View of socket connector
Figure 7-4 Connector Pinout for a PS/2 Mouse
Pin No.
Designation
Description
Input / Output
1
DAT
Data line, mouse
Input / Output
Unassigned
-
Ground
-
2
3
GND
4
+5V (fused)
Output
5
CLK
Clock line, mouse
Input / Output
6
-
Unassigned
-
PS/2 Keyboard
You can connect an external keyboard to your Box PC. The connector has the following pinout:
6
5
4
3
2
1
View onto the socket
Figure 7-5 Connector Pinout for an External Keyboard Connecting Cable
Pin-No.
Designation
Description
Input / Output
1
DAT
Data line, keyboard
Input/output
2
Unassigned
-
3
GND
Ground
-
4
P5VFK
+5V ( fused)
Output
5
CLK
Clock line, keyboard
Input/output
6
-
Unassigned
-
SIMATIC Box PC 620 Manual
A5E00131465-01
7-13
Hardware Information
USB Port
The Universal Serial Bus ports have the following pinout:
4
3
2
1
Figure 7-6 USB port
Pin-No.
Designation
Description
Input / Output
1
VCC
+5V (fused)
Output
2
- Data
Data line
Input / Output
3
+ Data
Data line
Input / Output
4
GND
Ground
-
The connector is of type A.
The port is rated as a high current USB (500mA).
7-14
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
PROFIBUS/MPI Socket Connector *
The PROFIBUS/MPI socket connector on the Box PC has the following pinout:
1
5
6
9
Figure 7-7 PROFIBUS/MPI Socket Connector
Pin No.
Designation
Description
Input/output
1
NC
Pin 1 is not assigned
-
2
NC
Pin 2 is not assigned
-
3
LTG_B
Signal line B of MPI module
Input/output
4
RTS_AS
RTSAS, control signal for received data
stream. The signal is “1” active when the programmable controller is sending.
Input
5
M5EXT
M5EXT return line (GND) of the 5 V power
supply. The current load caused by an external user connected between P5EXT and
M5EXT must not exceed max. 90 mA.
Output
6
P5 EXT
P5EXT power supply (+5 V) of the 5 V power
supply. The current load caused by an external user connected between P5EXT and
M5EXT must not exceed max. 90 mA.
Output
7
NC
Pin 7 is not assigned
-
8
LTG_A
Signal line A of the MPI module
Input/output
9
RTS_PG
RTS output signal of the MPI module. The
control signal is “1” when the programming
device is sending.
Output
Screen
*
on connector casing
Optional product feature
SIMATIC Box PC 620 Manual
A5E00131465-01
7-15
Hardware Information
Ethernet RJ45 Connection
LED yellow
LED green
1
8
Figure 7-8 Ethernet port
Pin-No.
Designation
Input / Output
1
TD+
Transmitted data
Output
2
TD–
Transmitted data
Output
3
RD+
Received data
Input
4, 5 *
SYMR
Internal 75 Ω output
-
Received data
Input
Internal 75 Ω output
-
Shield
-
LED green
Connection
-
LED yellow
Activity
-
6
7, 8 *
SYMT
S
*
7-16
Description
is not necessary for data transfer
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
VGA Socket Connector
The VGA socket connector on the Box PC has the following pinout:
6
1
5
10
11
15
Figure 7-9 VGA Socket Connector
Pin No.
Designation
Description
Input/Output
1
R
Red
Output
2
G
Green
Output
3
B
Blue
Output
4
-
Unassigned
-
5
GND
Ground
-
6
GND
Ground
-
7
GND
Ground
-
8
GND
Ground
-
9
5V
5 V (fused)
Output
10
GND
Ground
-
11
-
Unassigned
-
12
DDC_DAT
Display Data Channel Data
Input / Output
13
EXT_H
Horizontal synchronizing
pulse
Output
14
EXT_V
Vertical synchronizing pulse
Output
15
DDC_CLK
Display Data Channel Clock
Input / Output
SIMATIC Box PC 620 Manual
A5E00131465-01
7-17
Hardware Information
7.5.2
Assignment of the Front Ports on the Motherboard
Port
Position
Connector Description
Display (CMOS)
Internal
X420
Connection of LC displays with CMOS port
Display (LVDS)
Internal
X400
Connection of LC displays with single chip
LVDS port
I/O Front
Internal
X44
Port for front Front I/O
COM2
Internal
X26
Internal COM2 port
Display Port (CMOS, X420)
D-STN and TFT displays with 5V CMOS port and VGA resolution (640x480) can
be connected to this port. The display is selected and the D-STN/TFT signals
allocated automatically in accordance with the coding of the Display Select inputs.
The maximum cable length is 50 cm with a display clock rate of 25 MHz.
7-18
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Pin
Signal
Meaning
DSTN
DSTN
1
P5V_D_fused
+5V (fused) Display VCC
2
P5V_D_fused
+5V (fused) Display VCC
3
GND
4
CLK
Signal
Meaning
TFT
TFT
1
P5V_D_fused
+5V (fused) Display VCC
2
P5V_D_fused
+5V (fused) Display VCC
3
GND
4
CLK
5
GND
5
GND
6
LP
Horizontal Sync
6
HSync
Horizontal Sync
7
FP
Vertical Sync
7
VSync
Vertical Sync
8
-
-
8
R0
Signal Red Bit 0 (LSB)
9
-
-
9
R1
Signal Red Bit 1
10
UD6
Upper Data Bit 6
10
R2
Signal Red Bit 2
11
GND
11
GND
12
UD7
Upper Data Bit 7
12
R3
Signal Red Bit 3
13
UD2
Upper Data Bit 2
13
R4
Signal Red Bit 4
14
UD3
Upper Data Bit 3
14
R5
Signal Red Bit 5 (MSB)
15
GND
15
GND
16
UD1
Upper Data Bit 1
16
G0
Signal Green Bit 0 (LSB)
17
UD0
Upper Data Bit 0
17
G1
Signal Green Bit 1
18
LD3
Lower Data Bit 3
18
G2
Signal Green Bit 2
19
GND
19
GND
20
LD2
Lower Data Bit 2
20
G3
Signal Green Bit 3
21
LD1
Lower Data Bit 1
21
G4
Signal Green Bit 4
22
LD0
Lower Data Bit 0
22
G5
Signal Green Bit 5
(MSB)
23
GND
23
GND
24
25
26
27
28
29
30
31
32
33
34
UD5
UD4
LD7
GND
LD6
LD5
LD4
VCON
M
DispOn
Res.
24
25
26
27
28
29
30
31
32
33
34
B0
B1
B2
GND
B3
B4
B5
ENAB
DispOn
Res.
SIMATIC Box PC 620 Manual
A5E00131465-01
Shift Clock
Upper Data Bit 5
Upper Data Bit 4
Lower Data Bit 7
Lower Data Bit 6
Lower Data Bit 5
Lower Data Bit 4
Contrast voltage
Data enable
Display On
Reserved
Pin
Shift Clock
Signal Blue Bit 0 (LSB)
Signal Blue Bit 1
Signal Blue Bit 2
Signal Blue Bit 3
Signal Blue Bit 4
Signal Blue Bit 5 (MSB)
Data enable
Display On
Reserved
7-19
Hardware Information
Display Port (LVDS)
TFT displays with an LVDS port can be connected to this port. The connection of
18 bit displays up to a resolution of 1024x768 pixels is possible. The permissible
display clock rate is 20MHz to 66Mhz. The display is selected automatically in
accordance with the coding of the Select Inputs display. The display supply
voltages (3.3V and 5V) are connected via the graphic controller, dependent on therequirements of the connected displays. The maximum cable length is 50cm with a
transmission rate of 455MHz. Special cable properties are to be considered for the
pair of differential cables in accordance with the LVDS specification.
7-20
Pin No.
Designation
Description
Input / Output
1
P5V_D_fused
+5V (fused) VCC display
Output
2
P5V_D_fused
+5V (fused) VCC display
Output
3
RXIN0–
LVDS output signal bit 0 (-)
Output
4
RXIN0+
LVDS output signal bit 0 (+)
Output
5
P3V3_D_fused
+3.3V (fused) VCC display
Output
6
P3V3_D_fused
+3.3V (fused) VCC display
Output
7
RXIN1–
LVDS output signal bit 1 (-)
Output
8
RXIN1+
LVDS output signal bit 1 (+)
Output
9
GND
Ground
-
10
GND
Ground
-
11
RXIN2-
LVDS output signal bit 2 (-)
Output
12
RXIN2+
LVDS output signal bit 2 (+)
Output
13
GND
Ground
-
14
GND
Ground
-
15
RXCLKIN-
LVDS clock pulse (-)
Output
16
RXCLKIN+
LVDS clock pulse (+)
Output
17
GND
Ground
-
18
GND
Ground
-
19
Reserved
20
Reserved
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Allocation of the Display to Display Select Pins
The automatic configuration of one of 15 possible displays is effected via the
Display Select Inputs. The Display Select inputs are fitted with Pull-Up resistors,
i.e. if these inputs are not connected, they have a high level. In order to generate a
low level, the input must be connected to GND.
Pin No.
LCD_SEL3 LCD_SEL2 LCD_SEL1 LCD_SEL0 Display type
0
low
low
low
low
reserved
1
low
low
low
high
reserved
2
low
low
high
low
reserved
3
low
low
high
high
reserved
4
low
high
low
low
640 x 480 (VGA), TFT,
18 bits
5
low
high
low
high
reserved
6
low
high
high
low
1024 x 768 (XGA), TFT,
18 bits
7
low
high
high
high
800 x 600 (SVGA), TFT,
18 bits
8
high
low
low
low
reserved
9
high
low
low
high
reserved
10
high
low
high
low
reserved
11
high
low
high
high
reserved
12
high
high
low
low
reserved
13
high
high
low
high
reserved
14
high
high
high
low
reserved
15
high
high
high
high
No display / DDC selected display
SIMATIC Box PC 620 Manual
A5E00131465-01
7-21
Hardware Information
I/O Port for Front Control Elements
All the signals in addition to the Display and COM2 port which are necessary for
the connection of front control elements are applied to this port. The maximum
cable length is 50cm with a USB data transfer rate of 12MBaud.
7-22
Pin No. Designation
Description
Input / Output
1
GND
Ground
-
2
P12V
Power supply for inverter
Output
3
BL_ON
Backlight on (5V = On)
Output
4
P5V_fused
+5V (fused)
Output
5
GND
Ground
-
6
P3V3_fused
+3.3V (fused)
Output
7
K_CLK
Keyboard clock
Output
8
K_DATA
Keyboard data
Input / Output
9
M_CLK
Mouse clock
Output
10
M_DATA
Mouse DATA
Input / Output
11
P5V_fused
+5V (fused)
Output
12
USB_D1M
USB data- channel 1
Input / Output
13
USB_D1P
USB data+ channel 1
Input / Output
14
GND
Ground
-
15
LCD_SEL0
Display type-select signal 0
Input
16
LCD_SEL1
Display type-select signal 1
Input
17
LCD_SEL2
Display type-select signal 2
Input
18
LCD_SEL3
Display type-select signal 3
Input
19
RESET_N
Reset signal (low active)
Input
20
SPEAKER
Connection for system speaker
Output
21
HD_LED
HD LED, anode with 1kΩ in series
on motherboard
Output
22
DP_LED
MPI/DP LED, anode above 1kΩ in
series on motherboard
Output
23
Ethernet_LED
Ethernet LED, anode above 1kΩ in
series on motherboard
Output
24
TEMP_ERR
LED temperature error, anode with
1kΩ in series on motherboard
Output
25
RUN_R
LED watchDog error, anode with 1kΩ Output
in series on motherboard
26
RUN_G
LED watchdog o.k., anode with 1kΩ
in series on motherboard
Output
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Internal Serial Port COM2 (V.24)
This port is connected in parallel to the external COM2 port. Both ports can
therefore only be used alternatively. The assignment is executed in such a way
that a 1:1 connection to a 9 pin subminiature Cannon socket can be made when
using insulation piercing connecting devices. The maximum cable length is 100cm
with a data transfer rate of 9.6 Kbps.
7.5.3
Pin No.
Designation
Description
Input / Output
1
DCD
Receiving signal level
Imput
2
DSR
Readiness for operation
Input
3
RxD
Received data
Input
4
RTS
Switch on transmitter
Output
5
TxD
Transmitted data
Output
6
CTS
Ready to transmit status
Input
7
DTR
Terminal ready
Input
8
RI
Incoming call
Input
9
GND
Functional ground (reference
potential)
-
10
P5V
+5V power supply
Output
Assignment of the Internal Ports on the Motherboard
Port
Position
Connector
Memory
internal
X19, X20
Processor
internal
X1
Socket for MMC2 mobile processor
Bus extender
internal
X10
Socket for bus extender, assigned with ISA
and PCI bus signals
Power supply
105W
internal
X13
20 pin connector for DC signals of the power
supply unit with 85W
Power supply
85W
internal
X14
40 pin connector for DC signals of the power
supply unit with 85W
Floppy
internal
X5
two drives are possible (82078 compatible)
360kB, 720kB, 1.2MB, 1.44MB
3F0h-3F7h, 370h-377h, can be disabled
IRQ 6, edge-triggered
26 pin, socket for flex-lead (notebook
connection)
3.5” hard disk
internal
X41
170h-177h, 1F0h-1F7h, can be disabled
IRQ14, IRQ15, edge-triggered
40 pin, 2.54mm male connector
(3.5” HD, primary),
a maximum of two drives are operable
SIMATIC Box PC 620 Manual
A5E00131465-01
Description
2 SO-DIMM slot, 64Bit
7-23
Hardware Information
2.5” hard disks
internal
X4
170h-177h, 1F0h-1F7h, can be disabled
IRQ14, IRQ15, edge-triggered
44 pin, 2mm male connector (2.5” HD, primary),
a maximum of two drives are operable
CD ROM
internal
X3
170h-177h, 1F0h-1F7h, can be disabled
IRQ14, IRQ15, edge-triggered
44 pin, 2mm male connector (CD ROM,
secondary slave with connected LS120,
otherwise secondary master),
a maximum of one drive is operable
LS240
internal
X31
170h-177h, 1F0h-1F7h, can be disabled
IRQ14, IRQ15, edge-triggered
1x41 pin (Hirose DF9-41, LS240, secondary
master with connected drive),
a maximum of one drive is operable
TTY transmitter/
receiver*
internal
X70/71
PS connection
for 3.5” hard
disk
internal
X25
Power supply for 3.5” hard disk,
4 pin, male connector
PS connection
for CPU fan
internal
X29
Power supply for CPU fan,
3 pin, male connector
PS connection
for device fan
internal
X28
Power supply for device fan,
2 pin, male connector
Backup battery
internal
X24
Power supply for device fan,
2 pin, male connector
*
Connection for TTY transmitter/receiver
hybrid (physical interface)
Optional product feature
Port to the Bus Unit
The Box PC has a bus unit with a PCI slot and a shared ISA /PCI slot. Expansion
cards can be installed to ISA specification (Rev. 3.1) and PCI specification (Rev.
2.0) with a maximum length of 265mm (175 mm for shared ISA/PCI modules). All
the PCI slots can be used as masters. Only 5V PCI modules are operable.
The bus unit is executed as a purely passive module, i.e. there are only socket
contacts for the expansion cards and any necessary backup capacitors. The power
supply to the expansion cards is effected via the connection of the bus unit with the
basic board. The -5V voltage is not provided for in the power supply and is
produced from the -12V on the bus unit via in-phase voltage control.
7-24
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
DC Port of the Power Supply Unit 85W
The power supply unit has a connector (X2) through which all the signals on the
DC side are connected with the motherboard.
Pin
No.
Row A
Description
Pin
No.
Row B
Description
1
PS_PWROK
Power Good Signal
1
PS_PWROK
Power Good Signal
2
TTY_VCC
Potential–free VCC (15V ±
3V) for TTY port
2
TTY_VCC
Potential–free VCC (15V ±
3V) for TTY port
3
TTY_GND
TTY_GND
3
TTY_GND
TTY_GND
4
PS_NAU_N
Power failure early warning
alarm
4
PS_NAU_N
Power failure early warning
alarm
5
GND
GND
5
GND
GND
6
P12V
+12V
6
P12V
+12V
7
V_DC
for processor module
7
V_DC
for processor module
8
N12V
-12V
8
N12V
-12V
9
GND
GND
9
GND
GND
10
GND
GND
10
GND
GND
11
P3V3
+3.3V
11
P3V3
+3.3V
12
P3V3
+3.3V
12
P3V3
+3.3V
13
GND
GND
13
GND
GND
14
GND
GND
14
GND
GND
15
GND
GND
15
GND
GND
16
GND
GND
16
GND
GND
17
P5V
+5V
17
P5V
+5V
18
P5V
+5V
18
P5V
+5V
19
P5V
+5V
19
P5V
+5V
20
P5V
+5V
20
P5V
+5V
SIMATIC Box PC 620 Manual
A5E00131465-01
7-25
Hardware Information
DC Port of the Power Supply Unit 105W
The power supply unit has a connector (X2) through which all the signals on the
DC side are connected with the motherboard.
7-26
Pin no.
Designation
Description
1
P5V
+5V
2
P5V
+5V
3
P5V
+5V
4
P5V
+5V
5
P5V
+5V
6
PS_NAU_N
Power failure early warning alarm
7
PS_PWROK
Power Good Signal
8
GND
Ground
9
GND
Ground
10
GND
Ground
11
N12V
–12V
12
GND
Ground
13
GND
Ground
14
GND
Ground
15
P12V
+12V
16
P12V
+12V
17
P3V
+3.3V
18
P3V
+3.3V
19
P3V
+3.3V
20
P3V
+3.3V
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Port to the Floppy Disk Drive
This port is intended for the connection of a notebook floppy disk drive. The
maximum connection length of the data cable may not exceed 40cm.
Pin no.
Designation
Description
Input/Output
1
P5V
+5V
Output
2
INDEX_N
Index hole recognition
Input
3
P5V
+5V
Output
4
DS_N0
Drive 0 selection
Output
5
P5V
+5V
Output
6
DCHG_N
Disk change display
Input
7
n.c.
not connected
-
8
n.c.
not connected
-
9
Reserved
reserved
-
10
MOT_N0
Activate motor 0
Output
11
Reserved
reserved
-
12
DIR_SL_N
Step motor direction
Output
13
n.c.
not connected
-
14
STEP_N
Step motor pulse
15
GND
Ground
-
16
WR_DAT_N
Write data signal
Output
17
GND
Ground
-
18
WR_GAT_N
Enable data signal
Output
19
Reserved
reserved
-
20
TRACK_N0
Track 0 signal
Input
21
Reserved
reserved
-
22
WR_PRT_N
Write protection signal
Input
23
GND
Ground
-
24
RD_DAT_N
Read Data signal
Input
25
GND
Ground
-
26
SIDE_1_N
Page selection
Output
Assignment of the IDE Ports
The primary IDE port is intended for the alternative installation of
2.5” and 3.5” hard disks. 3.5” drives are connected via a 40 pin 2.54mm latching
connector, 2.5” drives via a 44 pin 2mm latching connector. The two connectors
are connected in parallel. The secondary IDE port is intended for the optional
connection of a CD ROM and / or an LS 240 drive. It is adaptable via a 44 pin
2mm latching connector. The maximum connection length of the data cables may
not exceed 40cm.
SIMATIC Box PC 620 Manual
A5E00131465-01
7-27
Hardware Information
Pin
X41
Meaning
1
RESET
Reset
2
GND
3
D7
Data signal D7
4
D8
5
6
Pin
X4/X3
Meaning
1
RESET
Reset
2
GND
3
D7
Data signal D7
Data signal D8
4
D8
Data signal D8
D6
Data signal D6
5
D6
Data signal D6
D9
Data signal D9
6
D9
Data signal D9
7
D5
Data signal D5
7
D5
Data signal D5
8
D10
Data signal D10
8
D10
Data signal D10
9
D4
Data signal D4
9
D4
Data signal D4
10
D11
Data signal D11
10
D11
Data signal D11
11
D3
Data signal D3
11
D3
Data signal D3
12
D12
Data signal D12
12
D12
Data signal D12
13
D2
Data signal D2
13
D2
Data signal D2
14
D13
Data signal D13
14
D13
Data signal D13
15
D1
Data signal D1
15
D1
Data signal D1
16
D14
Data signal D14
16
D14
Data signal D14
17
D0
Data signal D0
17
D0
Data signal D0
18
D15
Data signal D15
18
D15
Data signal D15
19
GND
19
GND
20
n.c.
Coding
20
n.c.
Coding
21
DREQ
DMA Request
21
DREQ
DMA Request
22
GND
22
GND
23
IOW_N
23
IOW_N
24
GND
24
GND
25
IOR_N
25
IOR_N
26
GND
26
GND
27
IORDY
I/O Ready
28
CSEL
Master/Slave
29
DACK_N
DMA Acknowledge
30
GND
31
IOCS16
27
IORDY
28
Reserved
29
DACK_N
30
GND
31
IOCS16
32
n.c.
33
AD_1
34
35
IO Write
I/O Read
I/O Ready
DMA Acknowledge
I/O Chip Select 16
IO Write
I/O Read
I/O Chip Select 16
32
n.c.
Address 1
33
AD_1
Reserved
reserved
34
reserved
reserved
AD_0
Address 0
35
AD_0
Address 0
Address 1
36
AD_2
Address 2
36
AD_2
Address 2
37
CS1_N
Chip Select 1
37
CS1_N
Chip Select 1
38
CS3_N
Chip Select 3
38
CS3_N
Chip Select 3
39
HDACT_N
HD active
39
HDACT_N
HD active
40
GND
40
GND
41
P5V
+5V power supply
42
P5V
+5V power supply
7-28
43
GND
44
reserved
reserved
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Connection for LS240 Drive
The optional LS240 drive is connected via this port. This port is connected in
parallel with the secondary IDE port. The connected LS240 drive is automatically
master (i.e. bootable drive) as the result of a special RC circuit. The maximum
connection length of the data cable may not exceed 40cm.
Pin No.
X31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
RESET
GND
D8
D7
D9
D6
D10
D5
D11
D4
D12
D3
D13
D2
D14
D1
D15
D0
GND
DREQ
GND
IOW_N
GND
IOR_N
GND
IORDY
Reserved
DACK_N
TBD
GND
Reserved
IOCS16
AD_2
AD_1
CS3_N
AD_0
HDACT_N
CS1_N
TBD
P5V
P5V
SIMATIC Box PC 620 Manual
A5E00131465-01
Meaning
Reset
Data signal D8
Data signal D7
Data signal D9
Data signal D6
Data signal D10
Data signal D5
Data signal D11
Data signal D4
Data signal D12
Data signal D3
Data signal D13
Data signal D2
Data signal D14
Data signal D1
Data signal D15
Data signal D0
DMA Request
IO Write
I/O Read
I/O Ready
DMA Acknowledge
reserved
I/O Chip Select 16
Address 2
Address 1
Chip Select 3
Address 0
HD active
Chip Select 1
+5V power supply
+5V power supply
7-29
Hardware Information
PS Connection for Hard Disk
The power supply of the 3.5” hard disk is effected via this connection.
Pin No.
Designation
Description
Input / Output
1
P12V
+12 V
Output
2
GND
Ground
–
3
GND
Ground
–
4
P5V
+ 5V
Output
Connection for CPU Fan
The CPU fan is connected via this connection.
Pin No.
Designation
Description
Input / Output
1
GND
Ground
–
2
+12V
Switched power supply
Output
3
CPU FAN_CLK
Speed signal
Input
Connection for Device Fan
The device fan is connected via this connection.
Pin No.
Designation
Description
Input / Output
1
+12V
Switched power supply
Output
2
GND
Ground
–
Connection for Backup Battery
The battery for the standby supply to the CMOS RAM is connected to this
connection. A 3.6 V lithium battery with a capacity of 750 mAh is used.
7-30
Pin No.
Designation
Description
Input / Output
1
+
Positive pole
Input
2
–
Negative pole
–
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
7.6
Bus Board
7.6.1
Design and Mode of Operation
The bus board is designed as a passive link between the motherboard and the
expansion modules. It is mounted by means of two screws.
The bus board has two ISA slots and two PCI slots, as well as a shared
ISA /PCI slot. The expansion modules are powered via the link between the bus
board and the motherboard. An external power supply (+5V and +12V) is provided.
Figure 7-10 Bus Board
SIMATIC Box PC 620 Manual
A5E00131465-01
7-31
Hardware Information
7.6.2
ISA Slot Pin Assignment
Pin
A1
–IOCHCK
A2
A3
Type*
Pin
Designation
Type
I
B1
0V
SD 07
I/O
B2
RESET DRV
SD 06
I/O
B3
+ 5V
VCC
A4
SD 05
I/O
B4
IRQ 9
I
A5
SD 04
I/O
B5
– 5V
VCC
A6
SD 03
I/O
B6
reserved
A7
SD 02
I/O
B7
– 12V
A8
SD 01
I/O
B8
reserved
A9
SD 00
I/O
B9
+ 12V
VCC
A10
–IOCHRDY
I
B10
0V
GND
A11
AEN
O
B11
–SMEMW#
A12
SA 19
I/O
B12
–SMEMR#
O
A13
SA 18
I/O
B13
–IOW#
I/O
A14
SA 17
I/O
B14
–IOR#
I/O
A15
SA 16
I/O
B15
–DACK3#
O
A16
SA 15
I/O
B16
DRQ 3
I
A17
SA 14
I/O
B17
–DACK1#
O
A18
SA 13
I/O
B18
DRQ 1
A19
SA 12
I/O
B19
–REFRESH#
I/O
A20
SA 11
I/O
B20
CLK
O
A21
SA 10
I/O
B21
IRQ 7
I
A22
SA 09
I/O
B22
reserved
I
A23
SA 08
I/O
B23
IRQ 5
I
A24
SA 07
I/O
B24
IRQ 4
I
A25
SA 06
I/O
B25
IRQ 3
I
A26
SA 05
I/O
B26
reserved
O
A27
SA 04
I/O
B27
TC
O
A28
SA 03
I/O
B28
BALE
O
A29
SA 02
I/O
B29
+ 5V
VCC
A30
SA 01
I/O
B30
OSC
O
A31
SA 00
I/O
B31
0V
*)
#
7-32
Designation
GND
O
I
VCC
I
O
I
GND
I/O determines the direction of the signals for the CPU board.
low active
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Pin
#
Designation
Type *
Pin
Designation
Type
C1
–SBHE#
O
D1
–MEMCS16#
I
C2
LA 23
I/O
D2
–IOCS16#
I
C3
LA 22
I/O
D3
IRQ 10
I
C4
LA 21
I/O
D4
IRQ 11
I
C5
LA 20
I/O
D5
reserved
I
C6
LA 19
I/O
D6
reserved
I
C7
LA 18
I/O
D7
reserved
I
C8
LA 17
I/O
D8
–DACK0#
O
C9
–MEMR#
I/O
D9
DRQ 0
I
C10
–MEMW#
I/O
D10
–DACK5#
O
C11
SD 08
I/O
D11
DRQ 5
I
C12
SD 09
I/O
D12
–DACK6#
O
C13
SD 10
I/O
D13
DRQ 6
I
C14
SD 11
I/O
D14
–DACK7#
O
C15
SD 12
I/O
D15
DRQ 7
I
C16
SD 13
I/O
D16
+ 5V
C17
SD 14
I/O
D17
reserved
C18
SD 15
I/O
D18
0V
VCC
I
GND
low active
Under normal conditions, the signals -SBHE, LA17 - LA23, -MEMR and MEMW
are operated as outputs (sending from the CPU). Only CPU boards which are
suitable for use as a master CPU for system bus access send and receive these
signals. A minus sign “-” in front of the signal name shows that the signal is LOW
active.
SIMATIC Box PC 620 Manual
A5E00131465-01
7-33
Hardware Information
7.6.3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
7-34
PCI Slot Pin Assignment
5V System Environment
Side B
Side A
-12V
TRST#
TCK
+12V
Ground
TMS
TDO
TDI
+5V
+5V
+5V
INTA#
INTB#
INTC#
INTD#
+5V
PRSNT1#
Reserved
Reserved
+5V (I/O)
PRSNT2#
Reserved
Ground
Ground
Ground
Ground
Reserved
Reserved
Ground
RST#
CLK
+5V (I/O)
Ground
GNT#
REQ#
Ground
+5V (I/O)
Reserved
AD[31]
AD[30]
AD[29]
+3.3V
Ground
AD[28]
AD[27]
AD[26]
AD[25]
Ground
+3.3V
AD[24]
C/BE[3]#
IDSEL
AD[23]
+3.3V
Ground
AD[22]
AD[21]
AD[20]
AD[19]
Ground
+3.3V
AD[18]
AD[17]
AD[16]
C/BE[2]#
+3.3V
Ground
FRAME#
IRDY#
Ground
+3.3V
TRDY#
DEVSEL#
Ground
Ground
STOP#
LOCK#
+3.3V
PERR#
SDONE
+3.3V
SBO#
SERR#
Ground
+3.3V
PAR
C/BE[1]#
AD[15]
AD[14]
+3.3V
Ground
AD[13]
AD[12]
AD[11]
AD[10]
Ground
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
5V System Environment
Side B
Side A
Ground
AD[09]
CONNECTOR KEY
CONNECTOR KEY
AD[08]
C/BE[0]#
AD[07]
+3.3V
+3.3V
AD[06]
AD[05]
AD[04]
AD[03]
Ground
Ground
AD[02]
AD[01]
AD[00]
+5V (I/O)
+5V (I/O)
ACK64#
REQ64#
+5V
+5V
+5V
+5V
CONNECTOR KEY
CONNECTOR KEY
Reserved
Ground
Ground
C/BE[7]#
C/BE[6]#
C/BE[5]#
C/BE[4]#
+5V (I/O)
Ground
PAR64
AD[63]
AD[62]
AD[61]
Ground
+5V (I/O)
AD[60]
AD[59]
AD[58]
AD[57]
Ground
Ground
AD[56]
AD[55]
AD[54]
AD[53]
+5V (I/O)
Ground
AD[52]
AD[51]
AD[50]
AD[49]
Ground
+5V (I/O)
AD[48]
AD[47]
AD[46]
AD[45]
Ground
Ground
AD[44]
AD[43]
AD[42]
AD[41]
+5V (I/O)
Ground
AD[40]
AD[39]
AD[38]
AD[37]
Ground
+5V (I/O)
AD[36]
AD[35]
AD[34]
AD[33]
Ground
Ground
AD[32]
Reserved
Reserved
Reserved
Ground
Ground
Reserved
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
Assignment of the Slot Specific PCI Bus Signals
PCI Socket
Pin No.
PCI Slot 1
shared ISA PCI Slot
B16
A6
clk (slot 1)
inta#
clk (slot2)
intb#
A7
B7
B8
B18
intc#
intb#
intd#
req1
intd#
intc#
inta#
req0
A17
A26
gnt1
ad29
gnt0
ad30
SIMATIC Box PC 620 Manual
A5E00131465-01
7-35
Hardware Information
7.7
Power Supply with 85W power output (AC and DC)
Technical Specifications
Voltage
Max. Current
Voltage Stability
+ 12 V
1.7 A
"4%
– 12 V
0.2 A
"6%
+5V
10 A
"3%
+ 3.3 V
4.2 A
"5%
Power-Good-Signal
Power-Good-Signal:
Input voltage
+5 V secondary
voltage
POWER GOOD
T1
T1:
T2:
T3:
preset time
hold–up time
save time
T2
T3
100 ... 500 ms
20 ms minimum (AC), 7 ms minimum (DC)
1 ms mimimum
Figure 7-11 Time Characteristics of the Power Good Signal
7-36
SIMATIC Box PC 620 Manual
A5E00131465-01
Hardware Information
7.8
Power Supply with 105W power output (AC and DC)
Technical Specifications
Voltage
Max. Current
Voltage Stability
+ 12 V
2.5 A
"4%
– 12 V
0.3 A
"5%
+5V
13.5 A
"3%
+ 3.3 V
8.5 A
"3%
Power-Good-Signal
Power–Good–Signal:
Input voltage
+5 V secondary
voltage
POWER GOOD
T1
T1:
T2:
T3:
preset time
hold–up time
save time
T2
T3
100 ... 500 ms
20 ms minimum
1 ms mimimum
Figure 7-12 Time Characteristics of the Power Good Signal
SIMATIC Box PC 620 Manual
A5E00131465-01
7-37
Hardware Information
7.9
Connecting Cables
SIMATIC S5 Connecting Cable
You can use the SIMATIC S5 connecting cable (not supplied with all variants) to
connect your PC to a SIMATIC S5 programmable controller. Please read the notes
in Chapter 3.
PU 7xx side
Connecting cable
AG side
25 pin male connector
6ES5 734-2BD20
15 pin male connector
aktiv
(in scope of delivery)
passiv
19
+U
330 ohms
9
2
18
21
–U
19
+U
330 ohms
9
6
7
10
–U
Housing
1
3
20
8
1
Screen/
housing
Figure 7-13 SIMATIC S5 Standard Connecting Cable
SIMATIC S7 Connecting Cable for MPI/DP
You can use the 6ES7901-0BF00-0AA0 connecting cable to connect your Box PC
to a SIMATIC S7 programmable controller. Please read the notes in Chapter 3.
7-38
SIMATIC Box PC 620 Manual
A5E00131465-01
Reinstallation of the Software
8
What Does This Chapter Contain?
This chapter describes how to reinstall software in case the preinstalled software
should be faulty.
Chapter Overview
Section
Description
Page
8.1
Restoring the Hard Disk
8-2
8.2
Installation of the Windows Operating System
8-6
8.3
Installing Drivers and Software
8-11
8.4
Installing and Operating the Burner Software
8-11
SIMATIC Box PC 620 Manual
A5E00131465-01
8-1
Reinstallation of the Software
8.1
Restoring the Hard Disk
8.1.1
Creating Partitions under Microsoft Windows 98
After installing a new hard disk it is necessary to create partitions with the program
“FDisk” when the partitions have errors or need to be changed.
Caution
By deleting or creating partitions or logical DOS hard drives all saved data is lost
on the hard disk. All drives on the hard disk will be erased.
The hard disk is delivered with the following installed (only for Windows 98
variants):
– a partition of the PRI DOS type, FAT 32 system,
– a partition of the EXT DOS type, FAT 32 system.
To restore the partitions to their original condition, please proceed as follows:
Primary Partition
1. To boot from the Recovery CD proceed as follows: When the BIOS message
Press <F2> to enter Setup
appears on the screen press the ESC key. After initialization a boot menu to
select the boot options is displayed.
2. Select “ATAPI CD ROM Drive”.
3. When “Microsoft Windows 98 Startup Menu” is displayed, select
“2. Boot for FDISK, FORMAT or Windows Me Setup”.
4. Start the Microsoft Windows 98 hard disk configuration program using
”A:\>FDisk”.
In the dialog box for large disk support select “[ Y]” for Yes when prompted “Do
you wish to enable large disk support (Y/N)...?” to create a FAT 32 partition.
5. Create a primary DOS partition with at least 4090 MB. When prompted “Do you
want to use the maximum available memory for creating the primary DOS
partition and do you want this partition to be activated?” select “[N]” for No for a
FAT 32 partition and then enter the desired partition size, for example,
6100 MB.
8-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Reinstallation of the Software
Creating an Extended Partition
In order to create an extended partition, you have to first boot from the
Windows Me Recovery CD as described in steps 1 to 4 above.
Using ”A:\>FDisk” start the Microsoft Windows Me hard disk configuration
program.
In the dialog box for large disk support select “[Y]” for Yes when prompted “Do you
wish to enable large disk support (Y/N)...?”.
Create an extended DOS partition for the rest of the disk space, assign a logical
drive and format it.
8.1.2
Creating Partitions under Windows NT
After installing a new hard disk it is necessary to create partitions when they
partitions have errors or need to be changed.
Caution
By deleting or creating partitions or logical DOS hard drives all saved data is lost
on the hard disk. All drives on the hard disk will be erased.
The hard disk is delivered with the following installed (only for versions delivered
with Windows NT):
– a partition of with the FAT16 file system with 2045 Mbytes,
– a partition of with the NTFS file system.
SIMATIC Box PC 620 Manual
A5E00131465-01
8-3
Reinstallation of the Software
To restore the partitions to their original condition, please do the following:
Primary Partition
1. To boot from the Recovery CD proceed as follows: When the message
Press <F2> to enter Setup
appears on the screen press the ESC key. After initialization a boot menu to
select the boot options is displayed.
2. Select “ATAPI CD-ROM Drive”.
3. When “Microsoft Windows 98 Startup Menu” is displayed, select
“2. Boot for FDISK, FORMAT or Windows NT Setup”.
4. Start the Microsoft Windows 98 hard disk configuration program with
”A:\>FDisk” (A is the CD-ROM drive).
Select the dialog box for enable large disk support for installing a FAT16
partition “activate support (Y/N)...? [ N ] ” for No.
5. Create a primary DOS-Partition of 2045 MB for a FAT 16 file system. Answer
the question “Do you wish to use the maximum available size...” for a 2045 MB
FAT16 partition with [Y] for Yes.
6. In order to continue with the next step “Create a Save to Disk Partition” the
primary partition needs to be formatted.
Use the Recovery CD to boot as described in steps 1 to 3 above and then
format drive C: with the program “Format”.
Type: ”A:\>Format C:”.
The creation of NTFS partitions is done under the Windows NT setup program.
Starting the Windows NT setup is described in Section 8.2.2.
8.1.3
Creating Partitions under Windows 2000
After installing a new hard disk it is necessary to create partitions when the
partitions have errors or need to be changed.
Caution
By deleting or creating partitions or logical DOS hard drives all saved data is lost
on the hard disk. All drives on the hard disk will be erased.
The hard disk is delivered with the following installed:
– a partition with the FAT32 file system ,
– a partition with NTFS file system.
To restore the partition to its delivery state, proceed as follows:
8-4
SIMATIC Box PC 620 Manual
A5E00131465-01
Reinstallation of the Software
Primary Partition, FAT32 File System
1. Boot from the Recovery CD and press ESC when the BIOS message
Press <F2> to enter Setup
appears. After initialization, select the boot options in the boot menu.
2. Select ”ATAPI CD-ROM Drive”.
3. Select ”2. Boot for FDISK, FORMAT or Windows 98 Setup” in the ”Microsoft
Windows Startup Menu” screen form.
4. Start the Microsoft Windows hard disk configuration program with ”A:\>FDisk”.
In the screen form select “Do you wish to enable large disk support (Y/N)...?
[ Y ]” for Yes to support data media with large memory capacity.
5. Create a primary DOS partition with 4090 MB. Enter [N] for “No” for the
question ”Do you want to use the maximum memory size available for the
primary DOS partition and do you want to activate this partition?” and set the
partition size to 6100 MB.
6. To format the partition from the Recovery CD, as described above in steps 1 to
3, reboot and then format drive C: with the “Format” program. Enter:
”A:\>Format C:”
(A: is the CD-ROM drive).
Creating an Extended FAT 32 Partition
In order to create an extended partition you have to boot from the Recovery CD as
described above in steps 1 to 4.
Create an extended DOS partition for the rest of the disk space.
In the Windows 2000 setup or under Windows 2000 the FAT 32 file system can be
converted to an NTFS file system with the “Format” function.
SIMATIC Box PC 620 Manual
A5E00131465-01
8-5
Reinstallation of the Software
8.2
Installing the Windows Operating System
Dependent on the device model, different operating system CDs are shipped:
a Recovery Microsoft Windows 98,
a Recovery Microsoft Windows NT,
a Recovery Microsoft Windows 2000.
8.2.1
Installing the Recovery CD for Microsoft Windows 98
If a Windows operating system is already installed or if the Box PC has been
started from a boot diskette, data transfer is carried out using the
OEMSETUP.EXE program. To do this, start the OEMSETUP.EXE program in the
root directory of the Recovery CD and continue the sequence as of point 5.
If no operating system is installed, proceed as follows:
1. Insert the Recovery CD in the CD ROM drive and connect the Box PC to the
mains.
2. To boot from the Recovery CD proceed as follows: When the BIOS message
Press <F2> to enter Setup appears on the screen press the ESC key.
After initialization a boot menu to select the boot options is displayed.
3. Select “ATAPI CD ROM Drive” .
4. When “Microsoft Windows 98 Startup Menu” is displayed, select
“1. Booten for CD-Recovery” .
If the hard disk has not been installed, first select “2. Boot for FDISK, FORMAT
or Windows-Setup (Section 8.1).
5. You have to acknowledge the “SIEMENS End User License Agreement” with
the F8 function key. Pressing ESC allows you to decline the agreement and
cancels the installation.
6. In the next screen you can select the components which are to be copied from
the CD to the hard disk. Transfer of at least the folder “WIN98” is necessary for
the Windows 98 installation or setup.
7. Select the drive for data transfer. The selected drive is not the installation drive
for Windows, but the drive on which the required installation files and
expansions are stored. For the Windows setup following transfer, you require
an available disk space of approximately 250 MB. As a standard, Windows 98
is installed in drive C:. Therefore, when selecting the drive make sure that there
will be sufficient disk space available on drive C: after data transfer.
Notice
By default, drive C: is used for the data transfer (Recovery).
Ensure that there is an available disk space of approximately 250 MB left on drive
C: after the selected recovery data have been copied.
8-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Reinstallation of the Software
8. After data transfer and end message acknowledgement Windows 98 setup can
be started directly using the
LW:\WIN98\SETUP.EXE program. (LW: Drive to which the WIN98 folder has
been transferred).
9. After having started setup.exe please follow the screen instructions.
8.2.2
Installing the Recovery CD for Microsoft Windows NT
This CD contains encoded data which can only be transferred to a SIEMENS
SIMATIC PC.
Data transfer is carried out with the OEMSETUP.EXE program on the CD ROM or,
after booting, from the CD-ROM with the recovery function.
After transferring the required data to the hard disk, the operating system can be
installed using the Windows NT setup program.
Windows NT Installation Sequence
If a Windows operating system is already installed or if the PC has been started
with a user created bootdisk, data transfer takes place using the OEMSETUP.EXE
program. To do this, start the OEMSETUP.EXE program in the root directory of the
Recovery CD and continue the sequence as of point 5.
If there is no operating system installed, proceed as follows:
1. Insert the Recovery CD in the CD ROM drive and reboot the system.
2. To boot from the CD proceed as follows: When the message
Press <F2> to enter Setup
appears on the screen press the ESC key. After intialization a boot menu to
select the boot options is displayed.
3. Select ”ATAPI CD ROM Drive”.
4. When “Microsoft Windows 98-Startup Menu” is displayed, select
“1. Boot for CD-Recovery”.
If the hard disk has not been installed, first select “2. Boot for FDISK, FORMAT
or Windows Setup” (Section 8.1).
5. You have to acknowledge the “SIEMENS End User License Agreement” with
the F8 function key. Pressing ESC allows you to decline the agreement and
cancels the installation.
6. In the next screen you can select the components which are to be copied from
the CD to the hard disk. Transfer of at least the folder “I386” is necessary for
the Windows NT installation or setup.
7. Select the drive for data transfer. The selected drive is not the installation drive
for Windows. For the Windows setup, you need an available disk space of
approximately 300 MB on the installation drive for Windows.
SIMATIC Box PC 620 Manual
A5E00131465-01
8-7
Reinstallation of the Software
Notice
By default, drive C: is used for the data transfer (Recovery).
Ensure that there is an available disk space of approximately 250 MB left on drive
C: after the selected recovery data have been copied.
8. Confirm the end massage box.
9. Start the Windows setup program
LW:\I386\Winnt.exe /b
LW is the drive where the recovery data have been copied.
You can find the information on installation of Windows NT on the Recovery CD in
the folder SUPPORT\BOOKS\.
Notice
If you want to become an expert user of Microsoft Windows NT Workstation, see
the “Windows NT Workstation Resource Kit” Version 4.0 (is not included in the
package). It contains specific information for administrators who are responsible
for installing, managing, and integrating Windows NT Workstation in a network or
multiuser environment.
8.2.3
Installing the Recovery CD for Microsoft Windows 2000
This CD contains encoded files which can only be transferred to a SIEMENS
SIMATIC PC.
Data transfer is made with the OEMSETUP.EXE program on the CD ROM, or after
booting from the CD ROM with the recovery function.
After transferring the required data to the hard disk, the operating system can be
installed using the Windows 2000 setup program.
8-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Reinstallation of the Software
Windows 2000 Installation Sequence
If a Windows operating system is already installed or if the PC has been started
with a user created bootdisk, data transfer takes place using the OEMSETUP.EXE
program. To do this, start the OEMSETUP.EXE program on the Recovery CD and
continue the sequence as of point 5.
If there is no operating system installed, then please do the following:
1. Insert the Recovery CD in the CD-ROM drive and reboot the system.
2. To boot from the CD proceed as follows: When the BIOS message
Press <F2> to enter Setup
appears on the screen press the ESC key. After intialization a boot menu to
select the boot options is displayed.
3. Select ”ATAPI CD ROM Drive”.
4. When “Microsoft Windows 98-Startup Menu” is displayed, select
“1. Boot for CD-Recovery”.
If the hard disk has not been installed, first select “2. Boot for FDISK, FORMAT
or Windows-Setup (Section 8.1).
5. You have to acknowledge the “SIEMENS End User License Agreement” with
the F8 function key. Pressing ESC allows you to decline the agreement and
cancels the installation.
6. In the next screen you can select the components which are to be copied from
the CD to the hard disk. Transfer of at least the folder “I386” is necessary for
the Windows 2000 installation or setup.
7. Select the drive for data transfer. The selected drive is not the installation drive
for Windows. For the Windows setup, you need an available disk space of
approximately 500 MB on the installation drive for Windows.
Notice
By default, drive C: is used for the data transfer (Recovery).
Ensure that there is an available disk space of approximately 300 MB left on drive
C: after the selected recovery data have been copied.
8. Confirm the end message box.
9. Start the Windows setup program
LW:\I386\Winnt.exe
LW is the drive where the recovery data have been copied.
10.Now follow the screen instructions.
SIMATIC Box PC 620 Manual
A5E00131465-01
8-9
Reinstallation of the Software
Setting the Language Selection for Windows 2000
The Multilanguage User Interface (MUI) allows you to set the Windows 2000
menus and dialogs to another language.
In order to install the MUI, run the program MUISETUP.EXE in the
CD_DRIVE:\MUI folder on the Recovery CD and follow the screen dialog to install
the desired languages.
The desired language for Windows 2000 menus and dialogs, as well as the
keyboard layout can be set via the control panel with the dialog Start > Settings >
Control Panel > Regional Options > tab “General” > box “Menus and
dialogs” and in the tab “Inputs”, box “Keyboard layout” .
In addition to the language for menus and dialogs, you can also set via Regional
Options the standard for the region with Set Default.
Your device is set to English menus and dialogs and a US keyboard when
delivered. You can set another language and keyboard via the control panel with
the dialog Start >Settings > Control Panel > Regional Options > tab ”General”,
box ”Menus and dialogs”> tab ”Input locales”, box ”Input language”.
8-10
SIMATIC Box PC 620 Manual
A5E00131465-01
Reinstallation of the Software
8.3
Installing Drivers and Software
To install the drivers and software from the “Documentation and Drivers” CD
supplied, proceed as follows:
Place the CD in the CD ROM drive.
Start the Start programm on the CD.The Acrobat Reader is started by the CD.
Navigate to the driver list (language, operating system and device dependent).
Please install the corresponding driver according to driver list.
Notice
When reinstalling Windows 98 and Windows 2000, make sure to install the chip
set driver prior to the other drivers.
When reinstalling Windows NT, the Windows NT ServicePack has to be installed
prior to all the other drivers. The Service Pack has to be reinstalled after a driver
installation.
8.4
Installing and Operating the Burner Software
A burner software is not installed in the delivery condition. You will find instructions
on installing and operating the burner software on the supplied CD ROM for the
burner software.
SIMATIC Box PC 620 Manual
A5E00131465-01
8-11
Reinstallation of the Software
8-12
SIMATIC Box PC 620 Manual
A5E00131465-01
Guidelines for handling electrostatic
sensitive devices (ESD)
A
Overview of chapter
In chapter
you will find
on page
A.1
What does ESD mean?
A-2
A.2
Electrostatic charging
A-3
A.3
Basic protective measures against discharge of static electricity
A-4
SIMATIC Box PC 620 Manual
A5E00131465-01
A-1
Guidelines for handling electrostatic
A.1
What does ESD mean?
Definition
All electronic components are equipped with high–integrated modules or
components. Conditioned by their technology, these electronic components are
extremely sensitive to overvoltages and therefore to discharges of static
electricity.
The short term ESD has been adopted for these Electrostatic Sensitive Devices/
assemblies.
Electrostatic sensitive assemblies are identified by the following symbol:
!
A-2
Caution
Electrostatic sensitive devices can be destroyed by voltages which are far below
the limit of perception of human beings. These voltages occur when you touch a
component or the electrical connections of a assembly without being
electrostatically discharged. The damage which arises in a assembly as a result of
overvoltage cannot usually be detected immediately, but only becomes apparent
after a lengthy operating period.
SIMATIC Box PC 620 Manual
A5E00131465-01
Guidelines for handling electrostatic
A.2
Electrostatic charging
Charging
Anyone who is not conductively connected to the electrical potential of their
surroundings can be electrostatically charged.
The maximum electrostatic voltage values which an operator can be charged with
when contacting the materials stated in the illustration are shown in Fig. A–1.
These values correspond to the specifications of IEC 801–2.
Voltage in kV
(kV)
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
1
synthetic material
2
wool
3 antistatic material, e.g.
wood or concrete
2
3
5 10 20 30 40 50 60 70 80 90 100
rel. humidity
in %
Figure A-1 Electrostatic voltages which an operator can be charged with
SIMATIC Box PC 620 Manual
A5E00131465-01
A-3
Guidelines for handling electrostatic
A.3
Basic protective measures against discharge of static
electricity
Ensuring a good ground connection
When handling electrostatic sensitive devices, ensure that your person, the
workplace and packaging are grounded. In this manner you avoid static charge.
Avoid direct contact
As a general principle, only touch electrostatic sensitive devices when this is
unavoidable (e.g. during maintenance work). To prevent discharge energy from
reaching and damaging sensitive components, hold the components in such a
way that you do not touch the pins or the printed conductors.
If you have to perform measurements on an assembly, discharge your body by
touching a grounded metallic object before carrying out the work. Use only
grounded measuring instruments.
A-4
SIMATIC Box PC 620 Manual
A5E00131465-01
Technical Specifications
SIMATIC Box PC 620 Manual
A5E00131465-01
B
B-1
Technical Specifications
B.1
Technical Specifications of the SIMATIC Box PC 620
General
Order nos.
Dimensions (w x h x d)
Weight
Supply voltage (UN)
Line voltage frequency, AC
Brief voltage interruption acc. to Namur
max. power consumption for 85W power supply
max. power consumption for 105W power
supply
max. current output (DC), according to form of
power supply
Noise emission
Enclosure
Safety
Protection class
Safety specifications with AC power supply
Safety specifications with DC power supply
Electromagnetic compatibility (EMC)
Emitted interference with power supply 105W
Emitted interference with power supply 85W
Noise immunity:
Mains borne disturbance variables on supply
lines
Noise immunity on signal lines
See order documentation
295x265x80 mm, without CD-ROM drive
295x265x100 mm, with CD-ROM drive
approx. 6kg (13.5 lbs.)
120 V (85 V to 132 V (AC),
or 230 V (170 V to 265 V) AC (autorange)
alternative: 24 V (20.4 bis 28.8 V) DC, SELV
50/60 Hz (47 to 63 Hz)
max. 20 ms at 0.85 UN
(max. 10 times per hour; min. recovery time 1 s)
120W
132W
+5V/ 10A or 13.5A
3,3V/4.2A or 8.5A
+12V/1.7 A or 2.5A
–12/0.2A or 0.3A (in total max. 85W or 105W)
< 55dB(A) to DIN 45635
IP20
Protection class I pursuant IEC 60536
UL1950/IEC 60950 corresponds to DIN VDE 0805
UL508
EN 55022 Class A (requirement for industrial sector)
for devices with AC power supply EN6100-3-2 class D
and EN61000-3-3
EN 55022 Class B (requirement for domestic and
industrial sector)
for devices with AC power supply EN6100-3-2 class D
and EN61000-3-3
±.2 kV
(to IEC 61000-4-4; Burst)
± 1 kV
(to IEC 61000-4-5; Surge symm)
± 2 kV
± 1 kV
(to IEC 61000-4-5; Surge unsymm)
(IEC 61000-4-4; Burst; length < 5 m)
± 2 kV
(IEC 61000-4-4; Burst; length > 5 m)
± 2 kV
(to IEC 61000-4-4:1995; Surge unsymm;
length > 30 m)
Noise immunity to discharges of static electricity ± 6 kV Contact discharge
(to IEC 61000-4-2)
Immunity to RF interference
± 8 kV Air discharge
(to IEC 61000-4-2)
10 V/m 80-1000 MHz, 80% AM (to IEC 61000-4-3)
Magnetic field
10 V/m 900 MHz and 1,89 GHz, 50% ED
(to IEC 61000-4-3)
10 V 9KHz- 80MHz
(to IEC 61000-4-6)
30 A/m 50Hz
(to IEC 61000-4-8)
B-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Technical Specifications
Ambient Conditions
Temperature
tested to DIN EN 60068-2-2:1994,
DIN IEC 60068-2-1,DIN IEC 60068-2-14,
–
–
operation
storage/transport
+ 5°C to +45°C
- 20°C to +60°C
–
gradient
(Max. speed of temperature change 10o C/h (50o F/h)
condensation not permitted)
tested to DIN IEC 60068-2-3, DIN IEC 60068-2-30,DIN
IEC 60068-2-56
Relative humidity
–
–
operation
storage/transport
5% to 80% at 25°C (no condensation)
5% to 95% at 25°C (no condensation)
–
gradient
(Max. speed of temperature change 10o C/h (50o F/h)
condensation not permitted)
Mechanical Specifications
Vibration *)
tested to DIN IEC 60068-2-6
–
10 to 58 Hz: 0.075 mm, 58 to 500 Hz: 9.8 m/s2
operation
– storage/transport
Shock
5 to 9 Hz: 3.5 mm, 9 to 500 Hz: 9.8 m/s2
tested to DIN IEC 60068-2-29
–
50 m/s2, 30 ms,
operation
– storage/transport
Special Features
Quality assurance
Motherboard
Processor
Internal processor cache
250 m/s2, 6 ms,
to ISO 9001
Main memory
Intel Pentium III / Celeron (see order documentation)
2x 16KB first level, 128/256/512 KB second level, dependent on the processor used
maximum 512 MB SDRAM,
2. Level Cache
Free expansion slots
memory configuration (see order documentation)
Processor internal
1 shared ISA/PCI (max 175 mm long),
–
1 PCI (max 265mm long)
5V 2A, 12V 0.3A, -12V 0.1A
max. permissible current input per ISA slot
–
max. permissible current input per PCI slot
–
in total (all slots)
Drives
Floppy disk drive / LS 240
Hard disk drive
CD ROM, CD RW/DVD(Combo) drive
5V 2A, 12V 0.3A, -12V 0.1A, only for 105W power
supply: 3.3 V 2A
5V 3A, 3.3V 4A, 12V 0.6A, -12V 0.15A may not be
exceeded
3,5” (1.44 MB) / 3.5” (240 MB, 120 MB or 1.44 MB)
3,5” , EIDE, UDMA33, hard disk capacity (see order
documentation)
650 MB / 4.7 GB
*) Restrictions for LS 240 with 120/240 MB data carrier and CD ROM /CD RW /DVD
10 to 58 Hz: 0.019 mm, 58 to 500 Hz: 2.5 m/s2
SIMATIC Box PC 620 Manual
A5E00131465-01
B-3
Technical Specifications
Graphics
Graphic controller
Graphic store
Resolutions/frequencies/colors
Ports
COM1 *1
UXGA LCD controller on the AGP bus
bis zu 32 MB SDRAM sind Bestandteil des Hauptspeichers und können konfiguriert werden (8/16/32MB)
CRT: up to 1600x1200/85 Hz / 65536 colors with
PC133
up to 1280x1024/85 Hz / 65536 colors with
PC100 memory modules
LPT1
Serial port 1 (V.24 / TTY), 25 pin subminiature Cannon
connector
Serial port 2 (V.24), 9 pin subminiature Cannon connector
Parallel port (standard, EPP and ECP mode)
VGA
Keyboard
Mouse
USB
Card bus
DP12 port, potentially isolated *2
Connection for printer with parallel port
VGA port, connection for external monitor
PS/2 keyboard connection
PS/2 mouse connection
3 channels (1x internal, 2x external)
1 port (max. type III)
9 pin subminiature Cannon socket, screw locking
COM2
•
Transfer rate
•
9,6 kBaud to 12 Mbaud, configurable by SW
•
Operating mode
•
potentially isolatedt*3:
- data lines A,B
- control lines RTS AS, RTS_PG
- 5V supply voltage (max. 90 mA)
•
connected to ground:
•
Physical interface
•
- shield of the DP12 connecting line
RS485, potentially isolatedt*3
•
Memory address area
•
0CC000h ...0CC7FFh or 0DC000h ...0DC7FFh
• Interrupts
Ethernet
Function Indicators (LEDs) on the Device
SIMATIC Box PC 620
• IRQ5, 10, 11 or 15 configurable by SW
Ethernet port (RJ45)
FD/LS240 access (on FD/LS240 drive on the side of
the computer box)
CD ROM access (on the CD ROM drive, if fitted)
*1
*2
*3
B-4
The line current (TTY) interface is an optional product feature
Optional product feature
Electrical isolation through an extra-low voltage safety circuit (SELV)
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
What Does this Chapter Contain?
This chapter contains a glossary in which you will find a list of the terminology used
in conjunction with the SIMATIC range of personal computers and programming
devices and a brief explanation of each of the terms.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-1
Glossary
A
AC
Alternating Current. Current that changes its direction at regular intervals.
Access Protection
Access to the programs and data of a programming device can be protected by
passwords. The user password or Superuser password can be assigned in the
BIOS Setup.
ACPI
Advanced Configuration and Power Interface enables the operating system to
supervise the power supply of each device connected to the computer. See also:
Power Management.
APM
Advanced Power Management monitors and conserves power on a PC-based
system, particularly a battery-powered laptop computer, by enabling programs to
communicate their power requirements so that the system can route power away
from unused hardware components.
Application
An application is a program which builds directly on, for example, the
MS-DOS/Windows operating system. Applications on your programming device
are, for example, the STEP 5 Basic package, STEP 7, etc.
ASCII-Editor
With an ASCII editor you can edit text files which are stored in ASCII code.
ATA
Advanced Technology Attachment is the official name for the disk drive interface
standard commonly known as Integrated Drive Electronics (IDE). See also: IDE.
AuthorsW
The authorization can be saved on the aithorization diskette again by the menu
command Start > Simatic > AuthorsW.
Authorization Diskette
The authorization disk contains the authorization required by the re-installation of a
software.
Glossary-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
B
Backup
Duplicate of a program, storage medium or database. Created to backup or to
protect irreplaceable data of working copies as a precaution against corruption or
destruction. Some applications automatically create backup copies, while
managing both the current version as well as the previous version that is stored on
the hard disk drive.
Base Memory
The base memory is a part of the main memory. It is 640 Kbytes for all
programming devices. The size is entered in the SETUP menu under the entry
“System Memory” and is not changed even if the memory is extended.
Battery
In personal computers, batteries are used as an auxiliary source of power when
the main power is shut off, as a power source for laptop and notebook computers
(rechargeable batteries, such as nickel cadmium, nickel metal hydride, and lithium
ion, are used), and as a method to keep the internal clock and the circuitry
responsible for the part of RAM that stores important system information always
powered up. Strictly speaking, only batteries that are not rechargeable are
classified as batteries.
BIOS
Acronym for Basic Input/Output System. On PC-compatible computers, the set of
essential software routines that tests hardware at startup, starts the operating
system, and supports the transfer of data among hardware devices.
Boot Diskette
Boot disk that contains a boot sector and an initial loader for the operating system.
Boot
Start or restart of the PG. During the boot sequence the operating system is
transferred from the system drive into the main memory.
Booting
Loading operation which transfers the operating system to the main memory.
Bps
The speed (in bits per second) with which information is transmitted over a data
link.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-3
Glossary
C
Cache
The cache memory buffers often used data to increase the speed of access. The
computer has two cache levels.
Cardbus interface
This interface is compatible with 32-bit Cardbus Cards with PCI performance
compliant with the PC Card standard.
CD ROM
Compact Disc Read Only Memory. Removable memory for large amounts of data.
Click
Pressing and immediately releasing the left mouse button; selects objects or
triggers commands.
Cold Boot
A startup process that begins with turning on the computer’s power. Typically, a
cold boot involves some basic hardware checking by the system, after which the
operating system is loaded from disk into memory.
COM1 Port
Serial V.24/modem-PLC interface. This interface is suitable for asynchronous data
transmission. It can also be used to connect printers with a serial interface.
COM2 Port
Serial RS-232 interface which can be used to connect a mouse or a printer.
Configuration Files
These are files containing data which define the configuration after booting.
Examples of such files are CONFIG.SYS, AUTOEXEC.BAT and the registry.
Configuration Software
The configuration software updates the device configuration when new modules
are installed. This is done either by copying the configuration files supplied with the
module or by manual configuration using the configuration utility.
Glossary-4
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
Controller
Integrated hardware and software controllers that control the functions of certain
internal or peripheral devices (for example, the keyboard controller).
Cursor
Collective term for mouse pointer and text cursor.
Cursor Control
Keypad on the keyboard for controlling the cursor.
D
DC
Direct Current. Unidirectional electrical current.
DIMM
Dual Inline Memory Module. Memory RAM chips that are installed on the PCB,
similar to the more common SIMM (Single Inline Memory Module) chips. The
DIMM with its 64-bit data bus architecture has connections on both sides which are
connected to different circuits for processing different instructions. SIMMs,
however, have a 32-bit data bus architecture where all lines are connected to the
same circuit for processing the same instructions. DIMMs can be installed in the
computer as single chip, SIMMs, on the contrary, only in pairs.
Device Configuration
The configuration of a programming device contains information on hardware and
device options, such as memory configuration, drive types, monitor, network
address, etc. The data are stored in a configuration file and enable the operating
system to load the correct device drivers and configure the correct device
parameters.
If changes are made to the hardware configuration, the user can change entries in
the configuration file using the SETUP program.
Disk Drive
The disk drive (floppy disk drive) is used to store programs and data on diskette
(write access) or to load from diskette to the computer (read access).
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-5
Glossary
Diskette
The diskette (floppy disk) is an external data access memory on which all types of
files and programs can be stored. The storage medium is a round magnetic disk in
a plastic cover to protect it from getting scratched.
Display
Flat screen monitor of the PG.
Dormancy
An energy saving power management mode that shuts down the monitor and hard
disk after all data found in the work memory have been saved to the hard disk
(Save to Disk). The PG will then be shut down.
Double-Click
Pressing and releasing the left mouse button very quickly twice in succession without moving the mouse. This action is normally to open an object or program.
Drives
Devices for operating rotary disk media (diskettes, hard disk, CDs).
Drivers
These are programs which are part of the operating system. They adapt user
program data to the specific formats required by I/O devices such as hard disk,
printers, and monitors.
Drop-Down Menu
In graphics-supported programs, a menu line is positioned on the top edge of the
screen. The menu titles contained in this line can be set either as drop-down or
pull-down menus. Drop-down menus “roll” down as soon as the mouse pointer
passes over a menu title. Pull-down menus only “roll” down when the menu title is
clicked on. Different functions can then be called from these menus by moving the
mouse and clicking on an item in a menu.
DVD
Digital Video Disc. A digital video disc can store greater amounts of data than a
traditional CD. A standard single-layer, single-sided digital video disc can store 4.7
GB of data; a two-layer standard increases the single-sided disc capacity to 8.5
GB. Digital video discs can be double-sided with a maximum storage of 17 GB per
disc. A digital video disc player is needed to read digital video discs; this player is
equipped to read older optical storage technologies.
Glossary-6
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
E
EIDE
Enhanced Integrated Drive Electronics. An extension of the IDE standard, EIDE is
a hardware interface standard for disk drive designs that house control circuits in
the drives themselves. It allows for standardized interfaces to the system bus while
providing for advanced features, such as burst data transfer and direct data
access. EIDE accommodates drives as large as 8.4 gigabytes (IDE supports up to
528 megabytes).
Energy Options
With Energy Options, you can reduce energy consumption of your computer while
it always remains to be ready to use. This function can be configured in Windows
via Settings > Control Panel > Energy Options.
EPROM/EEPROM Submodules
These are plug-in submodules with EPROM/EEPROM chips. S5 user programs
can be stored on them. These programmed submodules are then plugged into
specially designed slots in the programmable logic controller.
Ethernet
Local network (bus structure) for text and data communication with a transfer rate
of 10 Mbaud.
Extended Memory
Memory extensions can be installed in the programming device to increase the
width of the memory.
F
File
A complete, named collection of information, such as a program, a set of data
used by a program, or a user-created document. A file is the basic unit of storage
that enables a computer to distinguish one set of information from another.
Formatting
Formatting divides the memory area on a magnetic data medium into tracks and
sectors. Formatting deletes all the data on a data medium. Every data medium
must be formatted before it is used for the first time.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-7
Glossary
Function Keys
Function keys can be divided into two different types; the normal function keys
which are assigned a particular function of the computer (for example, delete key),
and programmable function keys (softkeys).
G
Gender Changer
The Gender Changer is used to convert the COM1/V24/PLC interface of the
SIMATIC PC family to a common socket.
H
Hard Copy
The output of the complete contents of the screen on a printer is called a hard
copy.
Hard Disk Drive
Hard disk drives (Winchester drives) are a form of magnetic disk memory where
the magnetic disks are permanently built into the drive.
Hibernate
See Dormancy.
HMI
Human Machine Interface
HTML
Hypertext Markup Language is the markup language used for documents on the
World Wide Web. HTML is an application of SGML (Standard Generalized Markup
Language) that uses tags to mark elements, such as text and graphics, in a
document to indicate how Web browsers should display these elements to the user
and should respond to user actions such as activation of a link by means of a key
press or mouse click.
HTTP
Hypertext Transfer Protocol is the protocol used to carry requests from a browser
to a Web server and to transport pages from Web servers back to the requesting
browser.
Glossary-8
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
Hub
In a network, a device joining communication lines at a central location, providing a
common connection to all devices on the network. The term is an analogy to the
hub of a wheel.
Hyperlink
A connection between an element in a hypertext document, such as a word,
phrase, symbol, or image, and a different element in the document, another
document, a file, or a script. The user activates the link by clicking on the linked
element, which is usually underlined or in a color different from the rest of the
document to indicate that the element is linked.
I
IDE
Integrated Device Electronics is a type of disk–drive interface in which the
controller electronics reside on the drive itself, eliminating the need for a separate
adapter card.
Infrarot
Acronym: IR. Having a frequency in the electromagnetic spectrum in the range just
below that of red light. Objects radiate infrared in proportion to their temperature.
Industrial Ethernet
Bus system based on the Ethernet standard. Components of the SIMATIC S5 and
S7 series (programming devices, programmable logic controllers, programmable
control systems) can be networked using Industrial Ethernet NICs.
Interface module
Module for the connection of peripheral hardware.
Interrupt
When the processor receives an interrupt, it suspends its current operations, saves
the status of its work, and transfers control to a special routine known as an
interrupt handler. This routine processes an instruction set to deal with the
particular situation that caused the interrupt. Interrupts can be generated by
various hardware devices to request service or report problems.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-9
Glossary
Interface
An interface is the connection between individual hardware elements such as
PLCs, programming devices, printers, or monitors via physical connections
(cables).
An interface is also the connection between different programs, to enable them
to work together.
Interface Module
Module which controls and extends the hardware periphery.
IRQ
Acronym for interrupt request. One of a set of possible hardware interrupts,
identified by a number. The number of the IRQ determines which interrupt handler
will be used. In the AT bus, ISA, and EISA, 15 IRQs are available. Each device’s
IRQ is hardwired or set by a jumper or DIP switch.
ISA
Industrial Standard Architecture (bus for expansion modules)
J
JEIDA
Japanese Electronics Industry Development Association. Association of Japanese
electronics manufacturers whose aim is to set up standards worldwide for the
miniaturization and flexible application of PC expansion cards. Cooperates with
PCMCIA.
K
Keyboard
A keyboard is the collection of keys which are used to input data, text, characters,
letters, numbers, special characters, and control commands in a computer. The
keyboard forms the input interface between the user and the computer.
Glossary-10
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
L
LCD
Liquid Crystal Display. Display type on the base of liquid crystals with a thin film
polarized molecular structure, enclosed between two transparent electrodes.
LED
Light Emitting Diode (for example, status display). Semiconductor diode that
transforms electrical energy into light.
Lid Switch
The device is switched off by closing the display lid.
LPT1 Port
The LPT1 port (Centronics port) is a parallel interface that can be used to connect
a printer.
LS240 Drive
Floppy disk drive that is capable of storing 240 MB of data on a single 3.5-inch
floppy disk. LS-240 drives are also compatible with other floppy disk formats.
M
Main Memory
Main memory is a RAM memory in the CPU that is accessed by the CPU during
user program processing.
Memory Card
Memory Cards in credit card format. memory for user programs and parameters,
for example, for programmable modules and CPs.
Micro Memory Card
New and very compact card for SIMATIC.
Memory Expansion
See Extended Memory
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-11
Glossary
Modem
Communications device that enables a computer to send and receive data over a
telephone line. Modulator and demodulator of a signal transmission facility. It
converts the digital pulses from a computer into analog signals (and vice versa).
Module
Modules are boards (printed circuit boards) which can be plugged into a
programmable logic controller or programming device. They are available, for
instance, as central controller modules, interface modules, or as bulk memory
modules.
Monitor
The device on which images generated by the computer’s video adapter are
displayed.
Mother Board
The mother board is the core of the programming device. From here data are
processed and stored, interfaces and device I/Os are controlled and managed.
Mouse
The mouse is a pointing device with which the user inputs coordinates (x,y). By
moving the mouse, the mouse pointer can be moved at will around the screen. By
pressing the left mouse button, the position is marked. The other mouse keys may
have different assignments according to the application. With the mouse, objects
can be selected, menus processed, and functions started.
Mouse Pointer
The mouse pointer is moved across the worktop (screen) by means of the mouse.
The mouse pointer selects, for example, objects which are to be processed.
MS-DOS
The single Microsoft-Disk-Operating-System is one of the standard OS for PCs.
Multimedia
The combination of sound, graphics, animation, and video. In the world of
computers, multimedia is a subset of hypermedia, which combines the
aforementioned elements with hypertext.
Glossary-12
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
N
Network
Link between programming devices and programmable controllers by means of
interface modules, physical cables, and the corresponding software to allow data
exchange between the devices.
O
Operating System
Collective term for all functions which, in conjunction with the hardware, control
and monitor execution of the user programs, the distribution of resources among
the individual user programs, and the maintenance of the operating mode (for
example, Windows 98, MS-DOS).
P
Parallel Interface
Information is transmitted byte for byte via a parallel interface (port). This means
that the transmission rate is very fast. The programming devices have one parallel
interface (LPT1).
Password
Unique sequence of characters that is entered for user identification. See Access
Protection.
PC
Personal computer
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-13
Glossary
PC Card
Trademark of the Personal Computer Memory Card International Association
(PCMCIA). Designation for auxiliary cards that conform with PCMCIA
specifications. The PC Card that has roughly the size of a credit card can be
plugged into a PCMCIA slot. Version 1 specifies cards of Type I with a thickness of
3.3 millimeters, which is conceived mainly for use as external memory. Version 2 of
the PCMCIA specification also defines a card Type II with thickness of 5 mm and a
card of the Type III with a thickness of 10.5 mm. Type II cards can realize devices
such as modems, fax and network interface cards. Type III cards are equipped
with devices that require more space, for example wireless communication
modules or rotary storage media (hard disk drives, for example).
PCI
Peripheral Component Interconnect (high-speed I/O expansion bus)
PCMCIA
(Personal Computer Memory Card International Association). Association of about
450 computer companies with the aim of setting worldwide standards for
miniaturizing PC expansion cards and making their use more flexible, offering the
market a basis for development. Cooperates with JEIDA. See Cardbus interface.
PG
Compact programming device especially for industrial applications. The PG is fully
equipped for programming SIMATIC PLCs.
PG LINK
Serial interface on a CPU, CP/IP module and coordination module (PG-MUX).
Used to connect a programming device. Some CPUs are optionally equipped with
two PG links.
Pixel
Pix Element (picture point). The pixel represents the smallest element that can be
reproduced on-screen or on a printer.
PIC
SIMATIC S5 programmable logic controller
Glossary-14
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
Plug and Play
Generally, a reference to the ability of a computer to automatically configure the
system for communication with peripheral devices (for example monitors, modems
or printers). The user can plug in a peripheral and ”play” it at once without
manually configuring the system. The Plug and Play PC requires both a BIOS that
supports Plug and Play and a corresponding expansion card.
Power Button
The device can be switched on or off with the power button.
Power Management
The Power Management of a modern PC can regulate the consumption of energy
of the most important components of the computer (e.g. monitor, hard disk and
CPU) individually, while the current active operations will not be affected. This
function is particularly important for portable computers.
PROFIBUS
Bus system based on the PROFIBUS standard. Components of the SIMATIC S5
and S7 series (programming devices, programmable logic controllers,
programmable control systems, distributed I/Os) can be networked using
PROFIBUS.
Programmable Logic Controller System
The programmable logic controllers (PLC) of the SIMATIC S5 system consist of
one or more CPUs and various I/O modules. The PLCs of the SIMATIC S7 system
(for example, S7-200, S7-300, S7-400) consist of one or more CPUs and various
I/O modules.
Programmable Controller (AS)
This programmable controller (PLC) consists of the central unit, a CPU and of
diverse I/O modules.
Pull-Down Menu
See Drop-Down Menu
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-15
Glossary
R
RAM
RAM (Random Access Memory) is a volatile read/write memory in which every
memory location can be addressed individually and its contents changed. RAM is
used to store data and programs.
Rechargeable Battery
Reachargeable battery is used as a power source for laptop and notebook
computers independent of external power supply. It also prevents the loss of data
as a result of power failure.
Restart
Warm start of a computer in operate state without switching off the power supply
(Ctrl + Alt + Del).
ROM
ROM (Read Only Memory) is a non-volatile memory in which every memory
location can be addressed individually. They contain factory set programs and data
that are not lost in the event of a power failure.
RS-232 Interface
The RS-232 interface is a standardized interface for data transmission. Printers,
modems and other hardware modules can be connected to a RS-232 interface.
RTC
Real Time Clock
S
SCSI Interface
Small Computer System Interface. Interface for connecting SCSI devices (hard
disk drives, CD-ROM drives).
Serial Interface
Data is transmitted one bit at a time via a serial interface (port); serial interfaces
are therefore slower than parallel interfaces.
Glossary-16
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
SETUP
A program in which information about the device configuration (that is, the
configuration of the hardware on the programming device) is defined. The device
configuration of the programming device is preset with defaults. Changes must
therefore be entered in the SETUP if a memory extension, new modules, or a new
drive are added to the hardware configuration.
SIMATIC S5 Memory Submodules
Memory submodules for SIMATIC S5 which are programmed with the PG and can
be plugged into an S5 programmable logic controller.
SIMATIC Memory Cards
Memory submodules in credit-card format for SIMATIC S5 and SIMATIC S7 which
are programmed with the PG and can be plugged into an S5 or S7 programmable
logic controller.
Software
The collective term for all programs which are used on a computer. The operating
system and the user programs are part of the concept “software”.
SOM
Safecard On Motherboard. Consists of a monitoring module on the motherboard,
the driver and the SOM program. Provides functions for monitoring various
temperatures and the program cycle (Watchdog).
Standby
Power saving status: for example, hard disk drive or display turned off.
Startup Disk
The bootstrap instructions coded into a computer’s ROM (read-only memory) and
executed at startup. The startup ROM routines enable a computer to check itself
and its devices (such as the keyboard and disk drives), prepare itself for operation,
and run a short program to load an operating-system loader program.
STEP 5
This is a software package which represents the basis for all other STEP 5
software packages. With the programming device (PG), this package is used to
program programmable logic controllers of the SIMATIC S5 family. The language
used is known as STEP 5.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-17
Glossary
STEP 7
Programming software for the creation of user programs for SIMATIC S7 control.
STN Display
Super Twist Nematic passive display
Suspend to Disk
Transition to power-off status, with prior saving of the system contents to the hard
disk drive.
Suspend to RAM
Transition to power-saving status, with prior saving of the system contents to the
RAM.
SVGA
Super Video Graphics Array is a video standard established by the Video
Electronics Standards Association (VESA) in 1989 to provide high-resolution color
display on IBM-compatible computers.
T
Text Cursor
The cursor shows where text may be entered, for example, in text editors and in
dialog windows. In many applications the position of the cursor can be changed by
moving and clicking with the mouse pointer.
TFT
Thin-Film-Transistor. Technology for liquid crystal displays (LCD). The display
consists of a large grid of LCD cells. Each one of the pixels represents a single
cell. The electrical field in the cells is supported by thin film transistors.
Touchpad
The Touchpad is used in many programs (with mouse control) as an input device
for cursor control and menu operation. The Touchpad works with touch-sensitive
sensors. The cursor can be moved over the screen with the touch of a finger.
Glossary-18
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
Touchscreen
The Touchscreen is a computer monitor developed and modified to recognize a
touch on the screen surface. The user can move the cursor or select an option by
touching the screen.
U
URL
Uniform Resource Locator is an address for a resource on the Internet. URLs are
used by Web browsers to locate Internet resources. A URL specifies the protocol
to be used in accessing the resource (such as http: for a World Wide Web page or
ftp: for an FTP site), the name of the server on which the resource resides (such
as //www.whitehouse.gov), and, optionally, the path to a resource (such as an
HTML document or a file on that server).
USB
Acronym for universal serial bus. A serial bus with a data transfer rate of
12 megabits per second (Mbps) for connecting peripherals to a microcomputer.
USB can connect up to 127 peripherals, such as external CD-ROM drives,
printers, modems, mice, and keyboards, to the system through a single,
general-purpose port. This is accomplished by daisy chaining peripherals together.
USB is designed to support the ability to automatically add and configure new
devices and the ability to add such devices without having to shut down and restart
the system (hot plugging).
User Interface
The software-controlled menus and screens on the monitor through which the user
communicates with the program.
User program
Contains all instructions, declarations and signal processing data that can be used
for system or a process control. It is assigned to a programmable module (for
example, CPU, FM) and can be split into smaller blocks (modules).
V
VGA
Video Graphics Array. Industrial standard graphics adapter for use with any
commonly used software.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-19
Glossary
Video Adapter
Also known as Video Controller, this electronic component generates the video
signal sent through a cable to a video display. The video adapter is usually located
on the computer’s main system board or on an expansion board, but it is
sometimes built into the terminal.
W
Warm Start
Restart of a computer in operate state without switching off the power supply (Ctrl
+ Alt + Del).
WAV
A file format in which Windows stores sounds as waveforms. Such files have the
extension .wav.
Windows
Windows is a multitasking graphical user interface environment that runs on
MS-DOS-based computers (Windows 3x and Windows for Workgroups), and as a
self-contained operating system for desktop computers (Windows 9x),
workstations, (Windows NT Workstation, Windows 2000 Professional ), and
network servers (Windows NT Server, Windows NT Enterprise Edition, Windows
2000 Server, and Windows 2000 Advanced Server). Windows provides a standard
graphical interface based on drop-down menus, windowed regions on the screen,
and a pointing device such as a mouse.
WWW
World Wide Web is the total set of interlinked hypertext documents residing on
HTTP servers all around the world. Documents on the World Wide Web, called
pages or Web pages, are written in HTML (Hypertext Markup Language), identified
by URLs (Uniform Resource Locators) that specify the particular machine and
pathname by which a file can be accessed, and transmitted from server to end
user under HTTP (Hypertext Transfer Protocol).
Working Memory
The memory in which a program is stored which can be processed. Also known as
main memory.
Glossary-20
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary
Write Protection
Write protection for files or diskettes
Write protection for files; this type of write protection is stored in the computer
and is allocated by the system manager.
Floppy disk write protection; for 3 1/2 in. diskettes by opening the write
protection hole.
W2k
Another name for Windows 2000.
SIMATIC Box PC 620 Manual
A5E00131465-01
Glossary-21
Glossary
Glossary-22
SIMATIC Box PC 620 Manual
A5E00131465-01
Index
A
D
AC Power Supply, 1-2, 2-2, 3-3
Acclimatization time, 1-1
Additional Software, 2-12
Ambient conditions, 1-1
Approvals, iii
AT Cards, 4-12
DC Power Supply, 1-2, 2-2, 3-3
Default Setup Settings, 5-29
Device Configuration, 5-2
Device Fan, 2-4
Device for holding down the modules, removal and installation, 4-14
Display Port, 7-20
Display Select Inputs, 7-21
Drive Side View, 2-4
Drives, 2-8
Floppy Disk Drive, 2-8
Hard Disk Drive, 2-11
LS 240 Drive, 2-8
B
Backup Battery, 2-12, 4-10
Safety instructions, 1-4, 2-12
BIOS Setup, 5-2
Error messages, 6-6
Menus, 5-2
System date, 5-6
System time, 5-6
Bottom View, 2-5
Burner Software, 8-11
Bus board, 4-5, 7-31
removal and installation, 4-23
C
Cardbus cards, 3-17
CD ROM drive, removal and installation,
4-19
CD ROM/CD RW Drive, 2-11
Certifications, iii
COM2, 2-2
Connecting
a keyboard, 3-15
a mouse, 3-14
the monitor, 3-13
the Printer, 3-12, 3-13
to the Power Supply Unit, 3-10
under Windows, 3-26
USB Devices, 3-16
via PROFIBUS, 3-23, 3-25
Connecting Cables, 7-38
Creating Partitions
under Microsoft Windows 200, 8-4
under Microsoft Windows 98, 8-2
Current Requirement, components, 7-2
SIMATIC Box PC 620 Manual
A5E00131465-01
E
EMC Directive, 1-5
Equipotential Grounding, 2-5
Equipotential Measures, 3-11
Error Diagnosis, 6-2
Error Messages, 6-6
ESD guidelines, 4-2
Ethernet, 2-3
Ethernet address, 3-2
Ethernet interface, 3-26
Ethernet RJ45 connection, 7-16
Expansion Cards
maximum dimensions, 4-12
removal and installation, 4-16
Expansion modules, 2-2
External keyboard, 7-13
External Ports, 7-9
F
Fan, 4-5
removal and installation, 4-25
Fan Monitoring, 7-8
Fitting positions, 3-8
Floppy disk drive, 4-5
removal and installation, 4-20
Front Ports, 2-4, 2-7
Further Support, v
Index-1
Index
G
O
Gender Changer, 7-11
Opening the PC, 4-4
H
P
Hard Disk Drive, 2-11
removal and installation, 4-17
Hardware Information, 7-1
Parallel Port, 7-12
Parallel Port , 2-3
PC Card, 2-2
PC Card Port, 3-17
PCI Cards, 4-13
PCI Slots, 2-2
Point to point connection, 3-19
Port Side View, 2-2
Ports, 2-2, 2-7, 7-9
COM1/MODEM/AG, 2-2
COM2, 2-2
Ethernet, 2-3
keyboard, 2-3
LPT1, 2-3
mouse, 2-2
PROFIBUS/MPI, 2-3
USB, 2-3
VGA, 2-3
Power Connection, 1-2
Power Supply Unit, 4-5
removal and installation, 4-22
technical data, 7-36
Preface, iii
Preparing for Operation, 3-10
Processor, 4-5
exchange, 4-26
PROFIBUS/MPI Network, 3-24
PROFIBUS/MPI port, 2-3
PROFIBUS/MPI Socket Connector, 7-15
PS/2 mouse port, 7-13
I
Installing
Burner Software, 8-11
Drivers, 8-11
Software, 8-11
the PC, 1-1, 3-3
the Recovery CD for Microsoft Windows
2000, 8-8
the Recovery CD for Microsoft Windows
98, 8-6, 8-7
Interface, RJ45 Ethernet, 3-26
K
Keyboard, 2-3
L
LPT1, 2-3
LS 240 Drive, 2-8, 4-5
removal and installation, 4-21
M
Memory capacity, 4-8
Memory extension, 4-5
Memory submodules, 4-8
Monitoring functions, 7-5
Fan Monitoring, 7-8
Temperature Monitoring, 7-6
Watchdog, 7-7
Motherboard, 4-6
removal and installation, 4-24
Mounting the PC, 3-4
Mouse, 2-2
Index-2
SIMATIC Box PC 620 Manual
A5E00131465-01
Index
R
Removal and installation
bus board, 4-23
CD ROM drive, 4-19
device for holding down the modules,
4-14
expansion cards, 4-16
fan, 4-25
floppy disk drive, 4-20
LS 240 drive, 4-21
motherboard, 4-24
power supply unit, 4-22
Repairs, safety instructions, 1-3
Reset Button, 2-4, 4-27
RJ45 Ethernet Interface, 3-26
S
Safety instructions
Backup battery, 1-4
power supply, 1-2
repairs, 1-3
ventilation, 1-1
Security, 1-7
Serial Number, 3-2
Serial Port, 7-10, 7-11
Service & Support, vi
Side View, 2-6
Standards, iii
Starting SETUP, 5-2
Superdisk, 2-10
Switching off the PC, 3-11
Switching on the PC, 3-11
SIMATIC Box PC 620 Manual
A5E00131465-01
System Resources, 7-4
T
Technical Specifications, B-2
Temperature monitoring, 7-5, 7-6
Training Center, v
Transport, 1-9
TTY Port, 3-20
Type Label, 2-4
U
Unpacking, 3-2
USB, 2-3
V
Ventilation, safety instructions, 1-1
VGA Port, 2-3, 2-7
VGA Socket Connector, 7-17
Voltage span, 3-10
W
Watchdog, 7-5, 7-7
WinAC Backup Battery, 2-6
X
XT Cards, 4-12
Index-3
Index
Index-4
SIMATIC Box PC 620 Manual
A5E00131465-01