Alcatel-Lucent 5620
SERVICE AWARE MANAGER | RELEASE 7.0
STATISTICS MANAGEMENT GUIDE
Alcatel-Lucent Proprietary
This document contains proprietary information of Alcatel-Lucent and is not to be disclosed
or used except in accordance with applicable agreements.
Copyright 2009 © Alcatel-Lucent. All rights reserved.
Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is
subject to change without notice.
Alcatel, Lucent, Alcatel-Lucent, the Alcatel-Lucent logo, and TiMetra are registered trademarks of
Alcatel-Lucent. All other trademarks are the property of their respective owners.
Copyright 2009 Alcatel-Lucent.
All rights reserved.
Disclaimers
Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design
engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous
environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life-support machines, or weapons
systems, in which the failure of products could lead directly to death, personal injury, or severe physical
or environmental damage. The customer hereby agrees that the use, sale, license or other distribution
of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at
the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from
any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the
use, sale, license or other distribution of the products in such applications.
This document may contain information regarding the use and installation of non-Alcatel-Lucent
products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent
tries to ensure that this information accurately reflects information provided by the supplier, please refer
to the materials provided with any non-Alcatel-Lucent product and contact the supplier for
confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete
information provided about non-Alcatel-Lucent products.
However, this does not constitute a representation or warranty. The warranties provided for
Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by
Alcatel-Lucent and its customers.
This document was originally written in English. If there is any conflict or inconsistency between the
English version and any other version of a document, the English version shall prevail.
When printed by Alcatel-Lucent, this document is printed on recycled paper.
Preface
About this document
The 5620 SAM User Guide and 5620 SAM Parameter Guide provide task-based
workflows and user documentation to allow you to:
•
•
•
•
•
•
•
use the GUI to perform tasks and maximize operator efficiency
auto-discover and administer the 5620 SAM-managed network
configure network devices
configure and enable QoS and routing policies
configure and enable customer services, such as VLL, IES, VPRN, and VPLS
perform network fault management
collect accounting and performance statistics
The 5620 SAM User Guide uses a task-based format. Each chapter contains:
•
•
•
•
•
overview information about the functionality described in the chapter
a workflow that describes the steps for configuring and using the functionality
a list of the GUI menus or commands related to the functionality
a list of the procedures related to the functionality
detailed procedures that list the configurable parameters on the associated forms
The 5620 SAM Parameter Guide provides:
•
•
•
•
parameter descriptions that include value ranges and default values
parameter options and option descriptions
parameter and option dependencies
parameter mappings to the 5620 SAM-O XML equivalent property names
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
iii
Preface
Procedure 1 To view 5620 SAM Parameter Guide parameter
descriptions from the 5620 SAM User Guide
You can click on a parameter name in a 5620 SAM User Guide procedure to open the
matching parameter description in the 5620 SAM Parameter Guide. Ensure the
following conditions are true beforehand:
•
•
1
2
the 5620 SAM Parameter Guide and 5620 SAM User Guide are located in and
opened from the same directory
Adobe Reader Release 5.0 or later is installed
To view a parameter description when the 5620 SAM User Guide and the 5620 SAM
Parameter Guide are open:
i
Open the 5620 SAM User Guide PDF using Adobe Acrobat.
ii
Open the 5620 SAM Parameter Guide PDF using Adobe Acrobat.
iii
Click on a parameter name in a procedure in the 5620 SAM User Guide. The
parameter description is displayed in the 5620 SAM Parameter Guide.
To view parameter descriptions when only the 5620 SAM User Guide is open:
i
Open the 5620 SAM User Guide PDF using Adobe Acrobat.
ii
Click on a parameter name in a procedure in the 5620 SAM User Guide. The
5620 SAM User Guide closes and the 5620 SAM Parameter Guide opens to
display the parameter description.
iii
Double-click on the Previous View button in Adobe Acrobat to re-open the
5620 SAM User Guide. The 5620 SAM User Guide opens and displays the
parameter from step ii.
iv
Click on the parameter name from step ii. The parameter description is
displayed in the 5620 SAM Parameter Guide.
About related documentation
There are several documents that describe the 5620 SAM and the managed devices.
• See the 5620 SAM Planning Guide for information about 5620 SAM scalability
•
•
•
•
iv
and recommended hardware configurations.
See the 5620 SAM | 5650 CPAM Installation and Upgrade Guide for information
about installing the 5620 SAM database, server, and client software.
See the 5620 SAM User Guide for information about using the client GUI to
perform network management functions.
See the 5620 SAM Parameter Guide for definitions, ranges, dependencies, and
default values for configurable 5620 SAM client GUI parameters.
See the 5620 SAM-O OSS Interface Developer Guide for information about using
the XML OSS interface to create OSS applications, for example, to perform
alarm monitoring and inventory control.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Preface
• See the 5620 SAM Routine Maintenance Procedures Guide for information about
developing and scheduling regular maintenance activities.
• See the 5620 SAM System Architecture Guide for information about software
component interaction.
• See the 5620 SAM NE Compatibility Guide for release-specific information about
the compatibility of managed-device features with different 5620 SAM releases.
• See the 5620 SAM Statistics Management Guide for information about managing
5620 SAM statistics collection and to view a list of the MIB counters that are
available for collection using the 5620 SAM.
• See the index file in the User_Documentation directory on the application DVD
for additional documentation information.
See the appropriate user documentation for information about device-specific CLI
commands, parameters, and installation. Contact your Alcatel-Lucent support
representative for information about specific network or facility considerations.
Procedure 2 To find the 5620 SAM user documentation
The user documentation is available from the following sources:
•
•
the User_Documentation directory on the product DVD-ROM
Help→5620 SAM User Documentation in the 5620 SAM client GUI main menu
Note — Users of Mozilla browsers may receive an error message when
using the User Documentation Index page (index.html) to open the PDF
files in the 5620 SAM documentation suite. The offline storage and
default cache values used by the browsers are the cause of the error
message.
Alcatel-Lucent recommends changing the offline storage (Mozilla
Firefox) or cache (Mozilla 1.7) values to 100 Mbytes to eliminate the
display of the error message.
Multiple PDF document search
You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a
common term. Adobe Reader displays the results in a single display panel. The
results are grouped by PDF file, and you can expand the entry for each file.
Note — The PDF files in which you search must be in the same
folder.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
v
Preface
Procedure 3 To search multiple PDF files for a common term
1
Open Adobe Acrobat Reader.
2
Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel
appears.
3
Enter the search criteria.
4
Click on the All PDF Documents In radio button.
5
Select the folder in which to search using the drop-down menu.
6
Click on the Search button.
Acrobat Reader displays the search results. You can expand the entries for each
document by clicking on the + symbol.
Conventions used in this guide
Table 1 lists the conventions that are used throughout the documentation.
Table 1 Documentation conventions
Convention
Description
Example
Key name
Press a keyboard key
Delete
Italics
Identifies a variable
hostname
Key+Key
Type the appropriate consecutive keystroke sequence
CTRL+G
Key–Key
Type the appropriate simultaneous keystroke sequence
CTRL–G
↵
Press the Return key
↵
—
An em dash indicates there is no information.
—
→
Indicates that a cascading submenu results from selecting a
menu item
Policies→Alarm
Policies
Procedures with options or substeps
When there are options in a procedure, they are identified by letters. When there are
substeps in a procedure, they are identified by roman numerals.
vi
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Preface
Example of options in a procedure
At step 1, you can choose option a or b. At step 2, you must do what the step
indicates.
1
2
This step offers two options. You must choose one of the following.
a
This is one option.
b
This is another option.
You must perform this step.
Example of substeps in a procedure
At step 1, you must perform a series of substeps within a step. At step 2, you must
do what the step indicates.
1
2
This step has a series of substeps that you must perform to complete the step. You
must perform the following substeps.
i
This is the first substep.
ii
This is the second substep.
iii
This is the third substep.
You must perform this step.
Important information
The following conventions are used to indicate important information:
Warning — Warning indicates that the described activity or situation
may, or will, cause equipment damage or serious performance
problems.
Caution — Caution indicates that the described activity or situation
may, or will, cause service interruption.
Note — Notes provides information that is, or may be, of special
interest.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
vii
Preface
viii
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Contents
Preface
iii
About this document .................................................................................. iii
Procedure 1 To view 5620 SAM Parameter Guide parameter
descriptions from the 5620 SAM User Guide ................................. iv
About related documentation........................................................................ iv
Procedure 2 To find the 5620 SAM user documentation.......................... v
Multiple PDF document search........................................................................ v
Procedure 3 To search multiple PDF files for a common term ................. vi
Conventions used in this guide....................................................................... vi
Procedures with options or substeps ................................................ vi
Important information................................................................ vii
Statistics overview
66 — Statistics overview
66.1
66.2
66.3
66.4
66-1
5620 SAM statistics overview ......................................................... 66-2
5620 SAM statistics types ............................................................. 66-3
Performance statistics.............................................................. 66-4
Accounting statistics................................................................ 66-5
Server performance statistics ..................................................... 66-6
5620 SAM statistics scalability ....................................................... 66-6
Accounting statistics................................................................ 66-7
Performance statistics.............................................................. 66-7
5620 SAM statistics and OSS applications........................................... 66-7
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
ix
Contents
Statistics collection configuration
67 — Statistics collection overview
67.1
67.2
67.3
68 — Performance statistics collection
68.1
68.2
68.3
68.4
69.2
69.3
69.4
x
68-1
Performance statistics collection overview ........................................ 68-2
Generic NE performance statistics support ..................................... 68-3
Workflow for performance statistics collection ................................... 68-3
Performance statistics collection procedures list................................. 68-4
Performance statistics collection procedures ..................................... 68-4
Procedure 68-1 To create or modify an NE MIB statistics policy using
a top-down method ........................................................... 68-4
Procedure 68-2 To modify an NE MIB statistics policy using a
bottom-up method ............................................................ 68-6
Procedure 68-3 To create or modify a specific MIB statistics policy
using a top-down method .................................................... 68-6
Procedure 68-4 To create or modify a specific MIB statistics policy
using a bottom-up method................................................... 68-8
Procedure 68-5 To configure polling for a MIB statistics class .............. 68-9
Procedure 68-6 To configure a statistics policy for MIB statistics ........ 68-10
69 — Accounting statistics collection
69.1
67-1
Statistics collection .................................................................... 67-2
Statistics policy types ................................................................. 67-2
Accounting policies ................................................................. 67-3
File policies .......................................................................... 67-4
Statistics policies.................................................................... 67-4
MIB statistics policies ............................................................... 67-4
Server performance statistics policies ........................................... 67-5
Statistics collection menus ........................................................... 67-5
69-1
Accounting statistics collection overview .......................................... 69-2
Queue filters ......................................................................... 69-2
Custom accounting records ........................................................ 69-3
Workflow for accounting statistics collection ..................................... 69-3
Accounting statistics collection procedures list ................................... 69-5
Accounting statistics collection procedures ....................................... 69-5
Procedure 69-1 To create or modify a file policy ............................. 69-6
Procedure 69-2 To create or modify an accounting policy .................. 69-7
Procedure 69-3 To configure a statistics policy for accounting
statistics on a SAP or an SDP .............................................. 69-10
Procedure 69-4 To configure a statistics policy for accounting
statistics on a network interface ......................................... 69-11
Procedure 69-5 To configure a statistics policy for accounting
statistics on a subscriber................................................... 69-12
Procedure 69-6 To configure a statistics policy for AA accounting
statistics on a subscriber................................................... 69-13
Procedure 69-7 To configure a statistics policy for an AA accounting
statistics application........................................................ 69-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Contents
Procedure 69-8 To configure a statistics policy for an AA accounting
statistics application group ................................................ 69-15
Procedure 69-9 To configure a statistics policy for an AA accounting
statistics protocol ........................................................... 69-16
70 — Server performance statistics collection
70.1
70.2
70.3
70.4
70-1
Server performance statistics collection overview ............................... 70-2
Workflow for server performance statistics collection........................... 70-2
Server performance statistics collection procedures list ........................ 70-2
Server performance statistics collection procedures............................. 70-2
Procedure 70-1 To configure a statistics policy for server
performance statistics........................................................ 70-3
Procedure 70-2 To configure a statistics collection policy for server
performance statistics........................................................ 70-4
Procedure 70-3 To delete statistics records ................................... 70-5
Statistics presentation
71 — Statistics presentation overview
71.1
Statistics presentation ................................................................ 71-2
Tabular statistics view ............................................................. 71-2
Graphical statistics view ........................................................... 71-3
72 — Viewing statistics
72.1
72.2
72.3
72.4
72.5
71-1
72-1
Viewing statistics overview ........................................................... 72-2
Workflow for viewing statistics ...................................................... 72-2
Viewing statistics menus .............................................................. 72-2
Viewing statistics procedures list.................................................... 72-2
Viewing statistics procedures ........................................................ 72-3
Procedure 72-1 To view on-demand statistics ................................. 72-3
Procedure 72-2 To view statistics for a set of objects ....................... 72-4
Procedure 72-3 To view network accounting statistics....................... 72-5
Procedure 72-4 To view performance statistics ............................... 72-6
Procedure 72-5 To view server performance statistics....................... 72-7
Procedure 72-6 To view service accounting statistics ........................ 72-8
Procedure 72-7 To view subscriber accounting statistics .................... 72-9
Procedure 72-8 To view per-subscriber AA accounting statistics ........... 72-9
Procedure 72-9 To view AA accounting statistics for an application ..... 72-10
Procedure 72-10 To view AA accounting statistics for an application
group .......................................................................... 72-11
Procedure 72-11 To view AA accounting statistics for a protocol ........ 72-12
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
xi
Contents
73 — Graphing statistics
73.1
73.2
73.3
73.4
73.5
73-1
Graphing statistics overview ......................................................... 73-2
Statistics Plotter .................................................................... 73-2
Real-time statistics data collection .............................................. 73-4
Workflow for graphing statistics ..................................................... 73-5
Graphing statistics menus ............................................................ 73-5
Graphing statistics procedures list .................................................. 73-5
Graphing statistics procedures....................................................... 73-5
Procedure 73-1 To configure the statistics graph parameters .............. 73-6
Procedure 73-2 To configure and plot a statistics graph..................... 73-6
Procedure 73-3 To modify a statistics graph ................................. 73-11
74 — Using the 5620 SAM-O to collect statistics
74.1
74-1
Using the 5620 SAM-O to collect statistics ......................................... 74-2
Third-party statistics collection process ........................................ 74-2
Third-party applications for processing statistics .............................. 74-3
Statistics content
75 — Statistics record format
75.1
75.2
75.3
75.4
75-1
Statistics types ......................................................................... 75-2
Performance statistics ................................................................ 75-3
Accounting statistics................................................................... 75-4
Server performance statistics ...................................................... 75-13
Appendices
A.
7210 SAS-E Release 1.0 statistics counters
A.1
B.
C.
xii
C-1
7250 SAS Release 2.0 statistics counters ............................................ C-2
7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics
counters
D.1
B-1
7210 SAS-M Release 1.0 statistics counters ......................................... B-2
7250 SAS Release 2.0 statistics counters
C.1
D.
7210 SAS-E Release 1.0 statistics counters.......................................... A-2
7210 SAS-M Release 1.0 statistics counters
B.1
A-1
D-1
7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters .................. D-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Contents
E.
7450 ESS Release 7.0 statistics counters
E.1
F.
G.
H.
I.
9500 MPR statistics counters
J-1
9500 MPR statistics counters .......................................................... J-2
Generic NE statistics counters
K.1
L.
I-1
7750 SR Release 7.0 statistics counters .............................................. I-2
J.1
K.
H-1
7710 SR Release 7.0 statistics counters ............................................. H-2
7750 SR Release 7.0 statistics counters
I.1
G-1
7705 SAR Release 2.0 statistics counters ............................................ G-2
7710 SR Release 7.0 statistics counters
H.1
F-1
7701 CPAA Release 3.0 statistics counters .......................................... F-2
7705 SAR Release 2.0 statistics counters
G.1
J.
7450 ESS Release 7.0 statistics counters ............................................ E-2
7701 CPAA Release 3.0 statistics counters
F.1
E-1
K-1
Generic NE statistics counters ........................................................ K-2
OmniSwitch Release 6.3.4 statistics counters
L.1
L-1
OmniSwitch Release 6.3.4 statistics counters ...................................... L-2
Index
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
xiii
Contents
xiv
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Statistics overview
66 — Statistics overview
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
66 — Statistics overview
66.1 5620 SAM statistics overview
66.2 5620 SAM statistics types
66-2
66-3
66.3 5620 SAM statistics scalability
66-6
66.4 5620 SAM statistics and OSS applications
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
66-7
66-1
66 — Statistics overview
66.1
5620 SAM statistics overview
The 5620 SAM provides a scalable platform for reliably collecting statistics from
managed Alcatel-Lucent NEs and from 5620 SAM servers. The statistics are
typically used for monitoring and troubleshooting the 5620 SAM network, and for
SLA and billing functions performed by OSS applications that connect to the
5620 SAM.
You can use the 5620 SAM to view statistics data directly in tabular or graphical
form, save the tabular or graphical data to a file in various formats, and export the
statistics data to OSS applications using the 5620 SAM-O interface.
Note — The 5620 SAM statistics collection constraints must be
considered when you configure statistics collection policies.
See “5620 SAM statistics scalability” in section 66.3 for more
information.
Before the 5620 SAM can collect statistics, policies must be configured to specify
the following:
•
•
•
•
the network or service objects from which to collect statistics
the counters to collect
the rate of collection
the length of time that the 5620 SAM database retains the collected statistics
Collected statistics are viewable in the 5620 SAM GUI from the Statistics tab of an
object properties form.
The 5620 SAM supports the collection of the following statistics:
• performance statistics
• accounting statistics
• server performance statistics
See “5620 SAM statistics types” for more information.
Performance and accounting statistics, which are NE-based, are collected by polling
MIB counters or transferring accounting files from NEs. MIB statistics policies can
be applied during or after NE discovery to enable the regular collection of
performance statistics on the NE. Server performance statistics, which provide
information about 5620 SAM server performance, are collected internally on each
5620 SAM server.
All statistics types, with the exception of file-based statistics, are available for
on-demand collection and real-time graphical display. On-demand collection returns
one MIB row for each click of the Collect button.
Scheduled and on-demand statistics are stored in the 5620 SAM database and are
available to all 5620 SAM operators. Statistics collected for real-time display are
available only for the duration of the session and for the operator that initiates the
session. Real-time statistics are not stored in the 5620 SAM database.
Statistics are stored in the 5620 SAM database for a configurable period. The
retention period is defined in a 5620 SAM statistics policy. When the retention
period elapses, the statistics are removed from the database.
66-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
66 — Statistics overview
The 5620 SAM allows you to back up statistics data to another location. See
chapter 18 of the 5620 SAM User Guide for information about backing up the
5620 SAM database.
Figure 66-1 shows the flow of statistics from different sources to various consumers.
On an NE, performance statistics are recorded in MIB tables, and accounting
statistics are recorded in accounting files. The MIB-based statistics are collected by
the 5620 SAM using SNMP. The statistics in the accounting files are transferred to
the 5620 SAM by FTP or SCP. Server performance statistics are collected internally
on a 5620 SAM server. All statistics types are stored in the 5620 SAM database.
Statistics in the database can be viewed using the 5620 SAM GUI and are available
to OSS applications. Statistics are transferred from the 5620 SAM database to the
OSS applications using FTP or SFTP. Statistics displayed in the 5620 SAM GUI can
be exported to files.
Figure 66-1 Statistics architecture
OSS applications
FTP, HTTP/SOAP,
SFTP, or HTTPS
5620 SAM server/database
Source: Internal format
Type: SAM performance statistics
FTP and
SCP
SNMP
5620 SAM client
Graphical (jpeg) and
tabular (csv, html) views
Network Element
Source: MIB
Type: Performance statistics
Source: Accounting files
Type: Accounting statistics
19719
66.2
5620 SAM statistics types
Table 66-1 summarizes the characteristics of the different statistics types.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
66-3
66 — Statistics overview
Table 66-1 Characteristics of statistics types
Characteristic
Statistics type
Performance
Accounting
• service
• network
• subscriber
• AA
Server performance
Typical use
NE troubleshooting and
monitoring
Billing, SLA compliance, and
trend analysis
5620 SAM server
troubleshooting and
monitoring
Source
NE MIBs
•
Internal 5620 SAM data
•
•
•
service—NE XML files and
MIBs
network—NE XML files
and MIBs
subscriber—NE XML files
and MIBs
AA—NE ISA-AA MIBs
On-demand collection
(using the Collect or
Collect All button)
Yes
No
Yes
Scheduled collection
(minimum collection
interval is 5 min)
Yes
Yes
Yes
Configure a specific or
general collection policy.
Configure file and accounting
policies.
Configure a collection policy.
Real-time graphing
Yes
Yes, if MIB-based
Yes
Historical graphing
Yes
Yes
Yes
Available through
5620 SAM-O
Yes
Yes
Yes
Collection default
Off
Off
On, using 15–min interval
•
•
minimum interval is
10 s
Not stored in the
5620 SAM database
Performance statistics
Performance statistics counters record NE data, for example, physical equipment
status and routing throughput, for monitoring and troubleshooting. See the
appendices for a complete list of the available performance statistics counters.
Performance statistics counters are collected from NE MIBs using SNMP. These
statistics can be scheduled for regular collection by the 5620 SAM server, or
collected on demand.
Performance statistics are stored in the 5620 SAM database and can be graphically
displayed in real time, or exported using the 5620 SAM-O interface. Historical
performance statistics can be viewed in tabular or graphical form using the
5620 SAM client GUI.
66-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
66 — Statistics overview
Accounting statistics
Accounting statistics counters typically record service or subscriber usage data for
billing or to ensure SLA compliance. See the appendices for a complete list of the
available accounting statistics.
Accounting policies define the schedules that NEs use for the regular collection of
accounting statistics. File policies specify how NEs store the accounting statistics
data. An NE performs scheduled accounting statistics collection after a file policy
and an accounting policy are deployed to the NE.
The 5620 SAM uses FTP or SCP to collect the accounting statistics files stored on
NEs. See the appropriate device documentation for more information about
accounting file storage on the device.
The supported accounting statistics types are:
• service accounting statistics—collected on every queue on every SAP that is
linked to an accounting policy. Service accounting statistics provide queue
throughput and drop information, and can be used for billing and SLA purposes.
• network accounting statistics—collected on every queue on every SDP, or
collected on network ports that are linked to an accounting policy. Network
accounting statistics measure forwarding class queue usage. This information is
used to monitor link utilization, and to identify network traffic patterns and
trends, for capacity planning and traffic engineering.
• subscriber accounting statistics—collected on a subscriber profile for residential
subscriber instances. Subscriber accounting statistics are used for billing and SLA
purposes.
• application assurance, or AA, accounting statistics—collected on applications,
application groups, and protocols. See the 5620 SAM User Guide for more
information about AA accounting statistics.
Note — SDP statistics collection is supported only on devices that are
in chassis mode B, C, or D. See the appropriate device documentation
for more information about configuring the chassis mode.
You can customize the statistics record in a service, subscriber, or AA accounting
policy by specifying the counters that are collected and the data thresholds for
collection. See chapter 69 for more information about custom accounting records.
Accounting statistics are stored in the 5620 SAM database and can be exported using
the 5620 SAM-O interface. The length of time that the 5620 SAM database stores
accounting statistics is specified during 5620 SAM database installation. You can
also change this retention period after installation. See chapter 18 of the 5620 SAM
User Guide for more information.
You can view historical and real-time accounting statistics in tabular or graphical
form using the 5620 SAM client GUI.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
66-5
66 — Statistics overview
Server performance statistics
You can collect server performance statistics such as the following from each
5620 SAM server in a 5620 SAM system:
• server statistics, which include memory usage and alarm counters
• network activity statistics, which include SNMP trap counters, accounting and
SNMP polled statistic record counters, and NE resynchronization counters
Note — A 5620 SAM server records network activity that is visible
to it; an NE may report a different level of activity during the same
time period.
You can collect server performance statistics on demand, or schedule regular
collection using a policy. Server performance statistics can also be collected and
graphically displayed in real time, or exported using the 5620 SAM-O interface.
Historical server performance statistics can be viewed in tabular or graphical form
using the 5620 SAM client GUI.
66.3
5620 SAM statistics scalability
The 5620 SAM supports the large-scale collection of statistics from the managed
network. Performance, accounting, and server performance statistics can be
collected according to a schedule and are stored in the 5620 SAM database. The
following formula defines the database capacity that scheduled collection consumes:
(number of objects to collect from) x (collection frequency) x (retention period)
The overall volume of collected statistics is limited by the size of the database.
Therefore, the number of objects and collection frequency should be specified to
meet operational requirements and remain within the database size constraints.
When a statistics collection policy or an accounting policy applies to a large number
of objects, the collection interval must be long enough to collect all of the data during
the collection period. If the statistics collection time exceeds the collection interval,
the 5620 SAM raises an alarm.
The maximum number of statistics the 5620 SAM can collect is specified in the
5620 SAM Planning Guide. To prevent statistics loss and 5620 SAM performance
degradation, Alcatel-Lucent recommends that you stay within the specified
maximum guidelines and ensure that each collection interval is long enough for the
number of statistics to be collected during the interval.
5620 SAM statistics collection is greatly enhanced by adding an auxiliary server to
the 5620 SAM system. The use of auxiliary servers distributes and load-balances the
statistics collection workload among multiple servers to increase the volume and
efficiency of statistics collection.
66-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
66 — Statistics overview
Real-time statistics collection and graphical display is supported for many network
and service objects. A 5620 SAM client can open up to five real-time plotter
windows, and each window can display up to four counters. If multiple open
statistics plotters point to the same NE or the same object on an NE, the NE receives
a large number of SNMP requests. Alcatel-Lucent recommends that you limit the
number of open statistics plotters for the same NE. You can use a span of control to
limit operator access to specific NEs and thereby reduce the number of simultaneous
real-time collections from a specific NE.
Note — The 5620 SAM limits the number of active MIB-based
accounting statistics plots per NE to four among all 5620 SAM
clients. For example, when two 5620 SAM clients each have two
active MIB-based accounting statistics plots associated with the same
NE, no other client can open a plot of the same type for the NE.
Accounting statistics
If you need to collect large numbers of accounting statistics, for example, more than
one million, Alcatel-Lucent recommends that you enable the statistics collection in
a staggered manner. This helps to prevent the first-time collection delays associated
with building the initial cache. For example, if you need to collect 6 million statistics
in a 15–min interval, enable 500 000 statistics and wait until the interval completes
before you add the next 500 000 statistics, and so on.
You can use custom accounting records to limit the processing requirements of
service, subscriber, or AA accounting statistics collection. See chapter 69 for more
information about custom accounting records.
The 5620 SAM uses FTP or SCP to retrieve an NE statistics file when the NE notifies
the 5620 SAM of the new file. The 5620 SAM retrieves and processes the files in the
order that it receives the notifications. An NE retains files only for the period
specified in the file policy; after this period, the NE deletes the files. The statistics
data in the files is lost if the files are not retrieved from the NE during this time.
Note — After an extended loss of connectivity to an NE that has an
active accounting policy, the 5620 SAM resumes accounting
statistics file retrieval by starting with the most recent statistics file.
When an accounting statistics counter is not supported by an NE or is excluded from
collection using a custom record, the counter value is not included in a statistics
record or displayed in the 5620 SAM client GUI.
Performance statistics
If any performance statistics remain to be collected at the end of a collection interval,
they are skipped and the next collection begins. This results in lost statistics because
the collection interval is too short.
66.4
5620 SAM statistics and OSS applications
The 5620 SAM can provide some or all collected statistics to OSS applications using
the 5620 SAM-O interface. See chapter 74 for information about using the
5620 SAM-O interface to retrieve statistics data from the 5620 SAM.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
66-7
66 — Statistics overview
66-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Statistics collection configuration
67 — Statistics collection overview
68 — Performance statistics collection
69 — Accounting statistics collection
70 — Server performance statistics collection
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
67 — Statistics collection overview
67.1 Statistics collection
67-2
67.2 Statistics policy types
67-2
67.3 Statistics collection menus
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
67-5
December 2009
67-1
67 — Statistics collection overview
67.1
Statistics collection
The 5620 SAM can be configured to collect statistics counters from managed
Alcatel-Lucent NEs and 5620 SAM servers. Statistics collection requires the
configuration and deployment of various policies.
Statistics policies can be configured in the following ways:
• for an entire network, or top-down, using the forms available through the
Tools→Statistics 5620 SAM main menu option
• for a specific object, or bottom-up, using the Statistics tab of an object
configuration form
A 5620 SAM operator can create statistics collection policies only for NEs that are
within the span of control of the current 5620 SAM user. However, an operator can
view statistics from NEs that are not within the current span of control.
67.2
Statistics policy types
You can configure the following policy types for statistics collection:
•
•
•
•
accounting policy—specifies the accounting record type and collection interval
file policy—specifies the storage criteria for accounting statistics files on NEs
statistics policy—specifies the storage criteria for statistics in the 5620 SAM
MIB statistics policy—specifies the collection of MIB-based statistics counters
from managed NEs, and is one of the following:
• NE MIB statistics policy—applies to all NE objects of the specified type
• specific MIB statistics policy—applies to a specific NE object
• server performance statistics policy—specifies the collection criteria for statistics
related to 5620 SAM server performance
Table 67-1 lists the policies required for each statistics type.
Table 67-1 Statistics policies
Statistics type
Accounting
File
Statistics
MIB
statistics
Server
performance
statistics
✓
✓
✓
—
—
Performance
—
—
✓
✓
—
Server performance
—
—
✓
—
✓
Accounting
•
•
•
•
67-2
Policy
service
network
subscriber
AA
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
67 — Statistics collection overview
Accounting policies
NEs collect accounting statistics using an accounting policy and an associated file
policy that are assigned to a SAP, SDP, network port, or subscriber profile.
An accounting policy specifies an accounting statistics record type, a collection
interval, an administrative state, and a file policy.
The 5620 SAM supports the following accounting policy types:
• service accounting policies—apply to SAPs, and specify the accounting records
to collect for services
• network accounting policies—apply to network ports and SDPs, and specify the
accounting records to collect for network resources
• subscriber accounting policies—apply to subscriber profiles and specify the
accounting records to collect for residential subscribers
• AA accounting policies—apply to applications, application groups, and
protocols, and specify the accounting records to collect for flows
An NE collects accounting statistics based on a specified collection interval and
writes the statistics data in XML format to a file on the NE. After the rollover period
specified in a file policy, the NE closes and compresses the file. The NE notifies the
5620 SAM that a new file is ready for processing, the 5620 SAM uses FTP or SCP
to obtain the file from the NE, and adds the file contents to the 5620 SAM database.
A third-party application can gather the statistics data and process it according to
your specifications.
Note — To conserve NE and 5620 SAM resources, Alcatel-Lucent
recommends that you disable an accounting policy on an object when
statistics for the object are not required.
When an accounting policy is administratively disabled, accounting statistics data is
not written to a file on the NE. When the accounting policy is re-enabled, the new
accounting data represents traffic activity since the re-enabling of the policy.
Because the statistics data accumulates in rolling counters, no information is lost.
You can customize the record in a service, subscriber, or AA accounting policy by
specifying the counters that are collected and the data thresholds for collection. See
chapter 69 for more information.
Changes to an accounting policy that is disabled apply immediately to all objects to
which the policy is applied. Changes to an accounting policy that is enabled take
effect at the beginning of the next collection period.
Consider the following before you configure an accounting policy.
• An accounting policy requires a file policy. If you deploy an accounting policy in
the absence of a file policy, a default file policy is automatically created.
• For service and network accounting policies, there can be one default policy.
Default accounting policies are not in effect until they are distributed to the NEs
by the 5620 SAM operator.
• There is a one-to-many relationship between accounting policies and accounting
objects. For example, one service accounting policy can apply to many SAPs, but
a SAP can have only one service accounting policy.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
67-3
67 — Statistics collection overview
File policies
A file policy specifies the relative size, storage location, and backup location of the
files on the NE that contain accounting statistics data. An NE collects accounting
statistics based on the collection interval specified for a SAP, network port, or
subscriber in an accounting policy, and writes the statistics data in XML format to a
file on the NE. After the rollover period specified in a file policy, the NE closes and
compresses the file. The NE then notifies the 5620 SAM that a new file is ready for
processing.
One file policy can be defined as a default policy and is automatically associated with
an accounting policy if no file policy is specified.
Statistics policies
A statistics policy specifies a retention period and alarm thresholds for a statistics
record. The retention period defines how long the 5620 SAM database retains the
statistics record after collection, which affects the database storage requirements.
When statistics collection is enabled, the oldest statistics records are periodically
removed from the database. When the collection interval is short and the retention
period is long, more disk space is required to store the statistics data.
Note — You can configure the length of time that the 5620 SAM
database globally retains accounting statistics data. See chapter 18 for
information on configuring the accounting statistics data retention
period.
MIB statistics policies
The collection of performance statistics from NEs is controlled by MIB statistics
polices that specify an administrative state, polling synchronization start time, and
collection interval. There are two types of MIB statistics policies:
• NE MIB statistics policies
• specific MIB statistics policies
Each type of MIB statistics policy contains a list of MIB entry policies. A MIB entry
policy defines the collection criteria for a specific MIB row. In an NE MIB policy, a
MIB entry policy applies to all objects on the NE that use the MIB entry. In a specific
MIB policy, the MIB entry policy applies only to the specified objects on the NE. For
example, the sapEgrQosPlcyQueueStatsEntry MIB entry applies to L2 and L3 SAPs.
In an NE MIB statistics policy, selecting this MIB entry enables collection of the
entry on all L2 and L3 SAPs on the NE. In a specific MIB statistics policy, selecting
this MIB entry enables collection only on the selected L2 or L3 SAPs.
If the statistics collection time required for a MIB entry exceeds the collection
interval specified in the MIB statistics policy, the 5620 SAM raises an alarm. A
5620 SAM operator can change the polling interval for a statistics class to prevent
this. See chapter 68 for information about modifying polling criteria.
The collection of MIB statistics counters is disabled by default. See chapter 68 for
information about enabling performance statistics collection.
67-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
67 — Statistics collection overview
NE MIB statistics policies
An NE MIB statistics policy defines the global collection of specific statistics on
specific NEs, for example, the port statistics from all ports in a group of NEs. In such
a collection scenario, configuring NE MIB policies rather than specific MIB policies
is more efficient and uses fewer collection resources. Alcatel-Lucent recommends
using NE MIB policies for general performance statistics collection on groups of
NEs, and specific policies to enable or disable collection for specific NE objects.
After an NE MIB statistics policy is applied to an NE, statistics are collected for all
objects on the NE, except for objects that have a specific MIB statistics policy. This
prevents statistics from being collected twice—once by the NE MIB policy and once
by the specific MIB policy.
Each NE requires an NE MIB statistics policy. The 5620 SAM has a default policy
that it applies to an NE automatically when no NE MIB statistics policy is specified.
The collection interval for each counter in the default policy is 15 min, and collection
is disabled by default to conserve NE resources.
Specific MIB statistics policies
A specific MIB statistics policy defines the collection of selected performance
statistics from specific objects on specific NEs to achieve a high statistics-collection
granularity. For example, to collect port statistics at one rate for access ports and
another rate for network ports, you can configure two policies that specify different
collection intervals, and explicitly specify the access or network ports to which each
policy applies. When a new access or network port is enabled, a 5620 SAM operator
can add the port to the specific MIB statistics policy to enable statistics collection on
the port.
The settings in a specific MIB statistics policy override the settings in an NE MIB
statistics policy, and can be used to disable statistics collection for specific objects.
For example, you enable statistics collection globally for an NE using an NE MIB
statistics policy, and then disable the collection of specific statistics using a specific
MIB statistics policy.
Server performance statistics policies
Server performance statistics provide information about 5620 SAM server
performance. You can specify the type of server statistics that are collected and the
collection interval for each type.
Each type of server performance statistic has the following:
• a collection policy that specifies a synchronization time and a collection interval
• a statistics policy that specifies the 5620 SAM database retention period
67.3
Statistics collection menus
Table 67-2 lists and describes the statistics collection menu items.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
67-5
67 — Statistics collection overview
Table 67-2 5620 SAM statistics collection menu items
Menu item
Function
Tools→Statistics→MIB Policies
Configure a MIB statistics policy.
Tools→Statistics→Server Performance
Statistics
View and modify server performance statistics
and collection policies.
View server performance statistics.
Tools→Statistics→Accounting Policies
Create a policy to manage accounting statistics
collection.
Tools→Statistics→File Policies
Create a file policy for use with an accounting
policy.
Tools→Statistics→Accounting Retrieval Status
View the accounting statistics collection status
for an NE.
Manage→Services
Create a policy for accounting statistics
collection on a SAP.
Policies→Application Assurance
View and modify AA protocol, application, and
application group accounting statistics and
collection policies.
View and modify per-subscriber AA protocol,
application, and application group accounting
statistics and collection policies.
View AA protocol, application, and application
group statistics.
Manage→Residential Subscribers
Create a policy for the collection of accounting
statistics on a subscriber.
View per-subscriber AA protocol, application,
and application group statistics.
67-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
68 — Performance statistics collection
68.1 Performance statistics collection overview
68-2
68.2 Workflow for performance statistics collection
68-3
68.3 Performance statistics collection procedures list
68.4 Performance statistics collection procedures
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
68-4
68-4
68-1
68 — Performance statistics collection
68.1
Performance statistics collection overview
Performance statistics provide information about physical equipment, routing, and
other NE properties for monitoring and troubleshooting purposes. See the
appendices for a complete list of the performance statistics that are available to the
5620 SAM.
Performance statistics collection is enabled using a MIB statistics collection policy
and associating the policy with one or more NEs or specific objects within the NEs,
for example, ports. For greater efficiency and collection granularity, the following
types of MIB statistics policies are available:
• NE MIB statistics policies—define collection at the NE level
An NE MIB statistics policy contains a list of the MIB entry policies that are
invoked for all objects on the NE.
• specific MIB statistics policies—define collection at the object level
A specific MIB statistics policy contains the same list of MIB entry policies as an
NE MIB statistics policy, but the MIB entry policies are applied only to the
objects specified in the specific MIB statistics policy. A specific MIB statistics
policy uses the concept of a monitored class, which is the type of object on which
to collect statistics, for example, a port or service site. The monitored object
instances must be specified in the specific MIB statistics policy. For example, if
port is selected as the monitored object, then the actual ports in the network to
which the policy applies must be specified, and become part of the policy.
Before the 5620 SAM performs a statistics collection based on a MIB statistics
policy, it checks for duplicate collection requests, such as when the same object is
included in an NE MIB policy and a specific MIB policy. If a duplicate is found, the
5620 SAM performs the collection on the object based on the specific policy rather
than on the NE policy.
For performance reasons, Alcatel-Lucent recommends using NE MIB policies to
collect statistics from all instances of an object on an NE, and specific policies to
enable or disable collection for specific NE objects. This is a much more efficient use
of NE resources than using a specific policy in which each object instance is
specified. For example, you can configure an NE MIB policy to collect OSPF routing
statistics on all the routing instances of the NE, and use a specific MIB policy to
collect statistics on a subset of the routing instances.
Specific and NE MIB policies can operate together to streamline statistics collection.
For example, to collect network port statistics at 5-min intervals and access port
statistics at 15-min intervals, you can create an NE MIB policy for all ports with a
15-min collection interval and create a specific policy for network ports with a 5-min
collection interval. At every third interval, when the two policy activations coincide,
the NE policy is used and duplicate collection is prevented.
Specific MIB policy settings override NE MIB policy settings. Table 68-1
summarizes the specific policy overrides for an object.
68-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
68 — Performance statistics collection
Table 68-1 MIB statistics policy overrides
For a given object
NE MIB policy
Specific MIB policy
Action
Collect
Collect
Statistic is collected once
Do not collect
Do not collect
Statistic is not collected
Collect
Do not collect
Statistic is not collected
Do not collect
Collect
Statistic is collected
NE MIB policies can be specified in NE discovery rules to ensure that statistics
collection starts immediately after the NE is discovered. Specific MIB polices must
be updated manually for specific objects on the new NE after it is discovered or new
objects are created.
For top-down performance statistics configuration, choose Tools→Statistics→MIB
Policies from the 5620 SAM main menu to systematically configure statistics for the
network. For bottom-up performance statistics configuration, configure the MIB
entry policy from the Statistics tab of the properties form for a specific object.
Generic NE performance statistics support
The 5620 SAM supports the collection of a limited set of statistics counters from
standard system, interface, and routing MIBs on generic NEs. These statistics are
processed and presented in the same manner as statistics from other devices. You can
view generic NE statistics on the Statistics tab of a generic NE interface properties
form, retrieve them using the OSSI, and display them graphically using the
5620 SAM Statistics Plotter.
Note 1 — To collect or view generic NE statistics from routing MIBs,
you require a valid 5650 CPAM license that has a third-party router
quantity greater than zero.
Note 2 — If persistent SNMP indexes are not enabled on a generic
NE, one or more generic NE interface indexes may change after a
generic NE reboots. This can cause a mismatch between the statistics
records collected before the reboot and the current interface indexes.
The 5620 SAM takes no action to recognize or correct such a
mismatch.
68.2
Workflow for performance statistics collection
1
Configure the MIB statistics policy for NEs. See Procedure 68-1 for the top-down
method. See Procedure 68-2 for the bottom-up method.
2
Configure the MIB statistics policy for specific objects. See Procedure 68-3 for the
top-down method. See Procedure 68-4 for the bottom-up method.
3
Specify the MIB statistics policy polling interval. See Procedure 68-5 for more
information.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
68-3
68 — Performance statistics collection
68.3
4
Configure the statistics policy for an object. See Procedure 68-6 for more
information.
5
If required, use a 5620 SAM client to view on-demand, scheduled, and real-time
performance statistics. See chapter 71 for information about viewing statistics.
6
Use the 5620 SAM-O interface to retrieve the performance statistics records from
the 5620 SAM for processing by a third-party application. See the 5620 SAM-O OSS
Interface Developer Guide for information about using the 5620 SAM-O to transfer
statistics records from the 5620 SAM database to an OSS client application.
Performance statistics collection procedures list
Table 68-2 lists the procedures for collecting performance statistics.
Table 68-2 Performance statistics collection procedures list
68.4
Procedure
Purpose
To create or modify an NE MIB statistics policy
using a top-down method
Configure an NE MIB statistics policy using
5620 SAM statistics management forms.
To modify an NE MIB statistics policy using a
bottom-up method
Configure an NE MIB statistics policy using a
5620 SAM discovery rule.
To create or modify a specific MIB statistics
policy using a top-down method
Configure a specific MIB statistics policy using
5620 SAM statistics management forms.
To create or modify a specific MIB statistics
policy using a bottom-up method
Configure a specific MIB statistics policy using an
object properties form.
To configure polling for a MIB statistics class
Specify the polling criteria for a MIB statistics
class.
To configure a statistics policy for MIB statistics
Specify how the 5620 SAM manages the
collected MIB statistics for a statistics class.
Performance statistics collection procedures
Use the following procedures to configure the collection of performance statistics
using the 5620 SAM.
Procedure 68-1 To create or modify an NE MIB statistics policy using
a top-down method
Perform this procedure to configure a policy for performance statistics collection on
one or more NE MIBs using the NE properties form.
68-4
1
Choose Tools→Statistics→MIB Policies from the 5620 SAM main menu. The Manage
MIB Statistics Policies form opens.
2
Choose NE MIB Statistics Policy (SNMP) from the object drop-down list.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
68 — Performance statistics collection
3
Perform one of the following.
a
Modify a MIB statistics policy.
i
Specify a filter to create a filtered list of MIB statistics policies. A list of
MIB statistics policies is displayed.
ii
Choose a MIB statistics policy from the list and click on the Properties
button. The NE MIB Statistics Policy (Edit) form opens.
Note 1 — When you change a MIB statistics policy for an NE, the change
affects all of the NEs to which the policy is assigned.
Note 2 — When you change a MIB statistics policy for a statistics class
of an object, the change applies to all objects that use the same
statistics class.
b
4
Click on the Create button to create a MIB statistics policy. The NE MIB
Statistics Policy (Create) form opens.
Configure the parameters:
•
•
•
Displayed Name
Polling Synchronization Time
Polling Admin State
5
Click on the Apply button. The form refreshes to display additional tab buttons.
6
Click on the Network Elements tab button.
7
Click on the Assign Sites button. A filter form opens.
8
Configure the filter criteria and click on the OK button. The Assign policy_name
form opens with a list of NEs displayed.
9
Select one or more NEs from the Unassigned Sites list, and click on the right arrow
button. The selected NEs move to the Assigned Sites list.
Note — You can also assign an NE MIB policy to NEs using a discovery
rule. Doing this does not affect the previously discovered NEs. See
Procedure 10-5 for more information.
10
Click on the OK button. The Assign policy_name form closes and the NE MIB
Statistics Policy form reappears.
11
Close the NE MIB Statistics Policy form. The Manage MIB Statistics Policies form
reappears.
12
Close the Manage MIB Statistics Policies form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
68-5
68 — Performance statistics collection
Procedure 68-2 To modify an NE MIB statistics policy using a
bottom-up method
Perform this procedure to configure a policy for performance statistics collection on
one or more NEs using the NE properties form.
1
Choose Administration→Discovery Manager from the 5620 SAM main menu. The
Discovery Manager form opens.
2
Click on the Managed State tab button.
3
Choose an NE from the list and click on the Properties button. The Node Discovery
Control (Edit) form opens with the General tab displayed.
4
Click on the MIB Statistics Policy tab button.
5
Click on the Select button. The Configure MIB Statistics Policy form opens.
6
Select a policy in the list and click on the OK button. The Configure MIB Statistics
Policy form closes and the Node Discovery Control form reappears.
7
Click on the OK button. The Node Discovery Control form closes and the Discovery
Manager form reappears.
8
Click on the OK button. A dialog box appears.
9
Click on the Yes button. The Discovery Manager form closes.
Procedure 68-3 To create or modify a specific MIB statistics policy
using a top-down method
Perform this procedure to configure a policy for performance statistics collection on a
specific NE MIB object using 5620 SAM main menu options.
68-6
1
Choose Tools→Statistics→MIB Policies from the 5620 SAM main menu. The Manage
MIB Statistics Policies form opens.
2
Choose Specific MIB Statistics Policy (SNMP) from the object drop-down list.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
68 — Performance statistics collection
3
Perform one of the following.
a
Modify a MIB statistics policy.
i
Specify a filter to create a filtered list of MIB statistics policies. A list of
MIB statistics policies is displayed.
ii
Choose a MIB statistics policy from the list and c. The Specific MIB
Statistics Policy form (Edit) opens.
Note — When you change a MIB statistics policy for the statistics class
of an object, the same changes apply to all other objects that use the
same statistics class.
b
4
Click on the Create button t o create a MIB statistics policy. The Specific MIB
Statistics Policy (Create) form opens.
Configure the parameters:
•
•
•
•
•
Auto-Assign ID
Policy ID
Displayed Name
Polling Synchronization Time
Polling Admin State
5
Click on the Select button. The Specific Stats Poller Policy form opens.
6
Choose an object type from the list and click on the OK button. The Specific Stats
Poller Policy form closes and the Specific MIB Statistics Policy form reappears with
the object type displayed in the Monitored Class Name field.
7
Click on the Apply button. The Specific MIB Statistics Policy form refreshes to
display additional tab buttons.
8
Click on the Monitored Objects tab button.
9
Click on the Add button. The Select monitored_object for Specific MIB Statistics
Policy form opens.
10
Configure the filter criteria and click on the Search button. A list of monitored
objects is displayed.
11
Select one or more objects in the list and click on the OK button. The Select
monitored_object for Specific MIB Statistics Policy form closes and the Specific
MIB Statistics Policy form reappears with the selected objects listed.
12
Click on the OK button. The Specific MIB Statistics Policy form closes and the
Manage MIB Statistics Policies form reappears.
13
Close the Manage MIB Statistics Policies form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
68-7
68 — Performance statistics collection
Procedure 68-4 To create or modify a specific MIB statistics policy
using a bottom-up method
Perform this procedure to configure a policy for performance statistics collection on a
specific NE MIB object using the object properties form.
1
Choose an object on which to configure the MIB statistics policy.
2
Right-click on the object and choose Properties from the contextual menu. The
properties form for the object opens with the General tab displayed.
3
Click on the Statistics tab button.
4
Click on the Statistics Policies button and choose Manage Specific MIB Policy from
the drop-down menu. The Manage Specific MIB Policy form opens.
5
Choose Specific MIB Statistics Policy (SNMP) from the object drop-down list.
6
Perform one of the following.
a
Modify a MIB statistics policy.
i
Specify a filter to create a filtered list of MIB statistics policies. A list of
MIB statistics policies is displayed.
ii
Choose a MIB statistics policy from the list and c. The Specific MIB
Statistics Policy form (Edit) opens.
Note — When you change a MIB statistics policy for the statistics class
of an object, the same changes apply to all other objects that use the
same statistics class.
b
7
Configure the parameters:
•
•
•
•
•
68-8
Click on the Create button t o create a MIB statistics policy. The Specific MIB
Statistics Policy (Create) form opens.
Auto-Assign ID
Policy ID
Displayed Name
Polling Synchronization Time
Polling Admin State
8
Click on the Select button. The Specific Stats Poller Policy form opens.
9
Choose an object type from the list and click on the OK button. The Specific Stats
Poller Policy form closes and the Specific MIB Statistics Policy form reappears with
the object type displayed in the Monitored Class Name field.
10
Click on the Apply button. The Specific MIB Statistics Policy form refreshes to
display additional tab buttons.
11
Click on the Monitored Objects tab button.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
68 — Performance statistics collection
12
Click on the Add button. The Select monitored_object for Specific MIB Statistics
Policy form opens.
13
Configure the filter criteria and click on the Search button. A list of monitored
objects is displayed.
14
Select one or more objects in the list and click on the OK button. The Select
monitored_object for Specific MIB Statistics Policy form closes and the Specific
MIB Statistics Policy form reappears with the selected objects displayed.
15
Click on the OK button. A dialog box appears.
16
Click on the Yes button. The Specific MIB Statistics Policy form closes and the
Manage Specific MIB Policy form reappears.
17
Close the Manage Specific MIB Policy form.
18
Close the object properties form.
Procedure 68-5 To configure polling for a MIB statistics class
Perform this procedure to configure a policy for performance statistics collection for
an NE MIB statistics class on an object.
1
Choose an object on which to configure the MIB statistics polling interval.
2
Right-click on the object and choose Properties from the contextual menu. The
properties form for the object opens with the General tab displayed.
3
Click on the Statistics tab button.
4
Choose a statistics class from the object drop-down list.
5
Click on the Statistics Policies button and choose MIB Entry Policy from the
drop-down menu. The MIB Entry Policy form opens with the General tab displayed.
Note — The MIB Entry Policy menu item is dimmed if you choose an
invalid performance statistics class.
6
Configure the parameters:
•
•
•
7
Polling Interval
Administrative State
Number of Varbind per PDU
Click on the OK button. A dialog box appears.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
68-9
68 — Performance statistics collection
8
Click on the Yes button. The MIB Entry Policy form closes and the object properties
form reappears.
9
Close the object properties form.
Procedure 68-6 To configure a statistics policy for MIB statistics
Perform this procedure to configure a policy for performance statistics collection on a
MIB statistics class.
1
Choose the object on which to configure the statistics policy.
2
Right-click on the object and choose Properties from the contextual menu. The
properties form for the object opens with the General tab displayed.
3
Click on the Statistics tab button.
4
Choose a statistics class from the object drop-down list.
5
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
6
Configure the parameters:
•
•
•
68-10
Retention Time (hours)
Administrative State
Threshold Reporting State
7
Click on the Thresholds tab button. The Thresholds tab contains a threshold
parameter for each counter in the statistics class.
8
Configure the threshold parameters. When a statistics counter threshold is
exceeded, the 5620 SAM raises a threshold-crossing alarm. See the statistics
tables in the appendices for a description of each statistics counter.
9
Click on the OK button. A dialog box opens.
10
Click on the Yes button. The Statistics Policy form closes and the object properties
form reappears.
11
Close the object properties form.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
69.1 Accounting statistics collection overview
69-2
69.2 Workflow for accounting statistics collection
69-3
69.3 Accounting statistics collection procedures list
69.4 Accounting statistics collection procedures
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-5
69-5
69-1
69 — Accounting statistics collection
69.1
Accounting statistics collection overview
Accounting statistics provide packet and octet throughput information for queues
that are associated with the following objects:
•
•
•
•
SAPs or SDPs, which provide service accounting statistics
network ports, which provide network accounting statistics
subscriber profiles, which provide subscriber accounting statistics
subscribers, which provide application assurance, or AA, accounting statistics
See the 5620 SAM User Guide for information about AA accounting statistics.
To collect accounting statistics, you need to create and apply the following:
• an accounting policy
• a file policy
• a statistics policy
See chapter 67 for a description of each policy type.
Queue filters
You can use the 5620 SAM to configure queue filters for accounting statistics so that
NEs use queues that do not have to be monitored. The NEs generate accounting data
files that include all of the configured queues. You specify the queue filter in the
nms-server.xml configuration file on the 5620 SAM main server, and must restart the
5620 SAM main server or run the nmsserver.bat or .bash file using the read_config
option.
When you configure a queue filter, the queue parameter is checked for each data
record; the queues that do not match the filter are discarded and are not processed by
the statistics collector. The corresponding values are not stored in the database and
are not exported to files. By default, queues not matching the filter are processed by
the statistics collector for statistics types.
For example, you can enable the processing of queues 1 and 2 from
combinedServiceEgressOctets and completeSubscriberIngressPacketOctets, and
queues 1, 2, and 3 for completeSubscriberEgressPacketOctets statistics classes by
including the following entry in the nms-server.xml file:
<accountingStatsFilter
combinedServiceEgressOctets="1,2"
completeSubscriberEgressPacketOctets="1,2,3"
completeSubscriberIngressPacketOctets="1,2" />
69-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
Custom accounting records
You can customize the record in an accounting policy to contain only the accounting
data that you require. This reduces the statistics-collection processing load and the
volume of data that collection generates. Custom accounting records allow you to
specify the following in an accounting policy:
• the statistics counters to include in each record, for example, packet counters but
not octet counters
• the queues to monitor for collection
• the following significant-change criteria that determine when an NE saves the
counter data to a file:
• a significant0change threshold
• a specified set of reference counters
• a specified set of reference queues
• override counters and queues that record data related to HSMDA scheduler
overrides
The following accounting policy types support the creation of custom records:
• service
• subscriber
• application assurance, or AA
An accounting policy can contain one custom record. The 7710 SR, 7450 ESS, and
7750 SR, Release 7.0 or later, support the use of accounting policies that contain a
custom record.
69.2
Workflow for accounting statistics collection
1
Ensure that FTP is enabled on the NEs from which you want to collect accounting
statistics. See chapter 9 of the 5620 SAM User Guide for information about device
commissioning.
2
Configure poller policies to enable 5620 SAM FTP or SCP access to the NEs, as
required. See chapter 10 of the 5620 SAM User Guide for information about
configuring poller policies.
3
Enable statistics collection on the appropriate object.
4
a
For service and subscriber accounting statistics, ensure that statistics
collection on the SAP to be monitored is enabled. See the appropriate access
interface management chapter in the Managing subscriber services volume of
the 5620 SAM User Guide.
b
For network accounting statistics, see the appropriate equipment
management procedure in chapter 34 of the 5620 SAM User Guide.
c
For AA accounting statistics, see chapter 60 of the 5620 SAM User Guide.
Configure a file policy with rollover and retention values that are appropriate for
the traffic volume, number of objects, and available file storage space. See
Procedure 69-1 for more information.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-3
69 — Accounting statistics collection
5
Configure an accounting policy. See Procedure 69-2 for more information.
6
Apply the accounting policy. You can apply one accounting policy to a SAP, SDP,
network object such as a port, or a subscriber profile.
Note — Alcatel-Lucent recommends this method of applying an
accounting policy rather than distributing the policy to NEs. The
5620 SAM distributes the policy to an NE when the policy is applied to
an object.
a
For service accounting statistics, apply the service accounting policy to a SAP
or SDP.
i
Administratively disable accounting on the SAP.
ii
Choose the newly created accounting policy.
See the appropriate access interface management procedure in the Managing
subscriber services volume of the 5620 SAM User Guide for more information.
b
For network accounting statistics, apply the accounting policy to a network
object such as a port. You can specify a network accounting policy when you
configure a port in network mode.
i
Administratively disable accounting for the network object.
ii
Choose the newly created accounting policy.
See the appropriate equipment management procedure in chapter 34 of the
5620 SAM User Guide for more information.
c
For subscriber accounting statistics, apply the accounting policy to a
subscriber profile.
i
Administratively disable accounting on the subscriber.
ii
Choose the newly created accounting policy.
See the appropriate subscriber management procedures in the Managing
subscriber services volume of the 5620 SAM User Guide for more information.
d
7
69-4
For AA accounting statistics, see chapter 60 of the 5620 SAM User Guide.
Configure a statistics policy to define the retention requirements for the
accounting statistics records.
a
For service accounting statistics, see Procedure 69-3.
b
For network accounting statistics, see Procedure 69-4.
c
For subscriber accounting statistics, see Procedure 69-5.
d
For AA accounting statistics per subscriber, see Procedure 69-6.
e
For AA accounting statistics for an application, see Procedure 69-7.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
f
For AA accounting statistics for an application group, see Procedure 69-7.
g
For AA accounting statistics for a protocol, see Procedure 69-9.
8
View the status of accounting statistics collection for NEs. See the appropriate
procedure in chapter 17 of the 5620 SAM User Guide for more information.
9
If required, use the 5620 SAM client to view accounting statistics. See chapter 71
of the 5620 SAM User Guide for more information.
10
Use the 5620 SAM-O interface to retrieve the accounting statistics records from
the 5620 SAM for processing by a third-party application.
See the 5620 SAM-O OSS Interface Developer Guide for more information about
using the 5620 SAM-O to transfer statistics records from the 5620 SAM database to
an OSS client application.
69.3
Accounting statistics collection procedures list
Table 69-1 lists the procedures to collect accounting statistics.
Table 69-1 Accounting statistics collection procedures list
69.4
Procedure
Purpose
To create or modify a file policy
Specify how often a statistics file is created on
a device and how long it is retained by the
device before it is deleted.
To create or modify an accounting policy
Specify the types of statistics to collect and the
collection frequency.
To configure a statistics policy for accounting
statistics on a SAP or an SDP
Specify how the 5620 SAM manages accounting
statistics on a SAP.
To configure a statistics policy for accounting
statistics on a network interface
Specify how the 5620 SAM manages accounting
statistics on a network interface.
To configure a statistics policy for accounting
statistics on a subscriber
Specify how the 5620 SAM manages accounting
statistics on a subscriber.
To configure a statistics policy for AA accounting
statistics on a subscriber
Specify how the 5620 SAM manages AA
accounting statistics on a subscriber.
To configure a statistics policy for an AA
accounting statistics application
Specify how the 5620 SAM manages AA
accounting statistics on an application.
To configure a statistics policy for an AA
accounting statistics application group
Specify how the 5620 SAM manages AA
accounting statistics on an application group.
To configure a statistics policy for an AA
accounting statistics protocol
Specify how the 5620 SAM manages AA
accounting statistics for a protocol.
Accounting statistics collection procedures
Use the following procedures to configure the collection of accounting statistics.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-5
69 — Accounting statistics collection
Procedure 69-1 To create or modify a file policy
Perform this procedure to configure a file policy that controls the management of
accounting statistics files on one or more NEs.
1
Choose Tools→Statistics→File Policies from the 5620 SAM main menu. The Manage
File Policies form opens.
2
Perform one of the following.
a
To create a file policy, click on the Create button. The File Policy (Create)
form opens.
b
To modify a file policy, perform the following steps.
i
Choose Local or Global from the Policy scope drop-down menu. When
you choose Local, you can specify a device by clicking on the Select
button and choosing a device from the list.
ii
Click on the Search button. A list of file policies is displayed.
iii
Select a file policy in the list and click on the Properties button. The File
Policy (Edit) form opens.
Note — You cannot modify or delete a file policy when the policy is
associated with an accounting policy that is administratively enabled.
You must set the Administrative parameter of the corresponding
accounting policy to Down before you can modify or delete the file
policy. See Procedure 69-2 for more information.
3
Configure the parameters, as required:
•
•
•
•
Auto-Assign ID
ID
Displayed Name
Description
•
•
•
•
Rollover (minutes)
Retention (hours)
Drive
Storage Drive – Backup
Note — Ensure that the NE resources are sufficient to support the file
policy and associated accounting policy specifications. The collection,
retention, and rollover intervals must be appropriate, and the statistics
must be regularly retrieved from the NEs.
69-6
4
Click on the Apply button. The File Policy form refreshes.
5
Click on the Switch Mode button. A dialog box appears.
6
Click on the Yes button. The configuration mode changes from Draft to Released.
7
Close the File Policy form. The Manage File Policies form reappears.
8
Close the Manage File Policies form.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
Procedure 69-2 To create or modify an accounting policy
Perform this procedure to configure a policy that specifies the type and frequency of
accounting statistics collection.
1
Choose Tools→Statistics→Accounting Policies from the 5620 SAM main menu. The
Manage Accounting Policies form opens.
2
Perform one of the following.
3
a
To create an accounting policy, click on the Create button. The Accounting
Policy (Create) form opens with the General tab displayed.
b
To modify an accounting policy, perform the following steps.
i
Choose Local or Global from the Policy scope drop-down menu. When
you choose Local, you can specify a device by clicking on the Select
button and choosing a device from the list.
ii
Click on the Search button. A list of accounting policies is displayed.
iii
Select an accounting policy in the list and click on the Properties
button. The Accounting Policy (Edit) form opens with the General tab
displayed.
Configure the parameters:
•
•
•
•
•
Auto-Assign ID
ID
Displayed Name
Description
Type
•
•
•
•
Default
Collection Interval (m)
Use Default Interval
Administrative
See Table 75-3 for descriptions of the Type parameter options.
4
Choose a file policy.
i
Click on the Select button. The Select a File Policy form opens.
ii
Choose an appropriate file policy.
iii
Click on the OK button. The Select a File Policy form closes, and file policy
name is displayed on the Accounting Policy form.
Note — A file policy with default parameter values is automatically
created and associated with the accounting policy if a file policy not is
specified. When a file policy is automatically created, verify that the
file policy parameters are appropriate for the accounting policy.
5
Click on the Apply button. The Accounting Policy form refreshes.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-7
69 — Accounting statistics collection
6
7
Perform one of the following.
a
If you choose Custom Record AA Subscriber for the Type parameter, go to
step 7.
b
If you choose Custom Record Service or Custom Record Subscriber for the
Type parameter, go to step 8.
Perform the following steps.
i
Click on the Custom Record tab button. The Significant Change Criteria tab
is displayed.
ii
Configure the parameters:
•
•
iii
Click on the Application Assurance Counters tab button.
iv
Configure the parameters:
•
•
•
v
8
Significant Change Delta
Any
Application Assurance Counters
From Subscriber Counters
To Subscriber Counters
Go to step 11.
Perform the following steps.
i
Click on the Custom Record tab button. The Significant Change Criteria tab
is displayed.
ii
Configure the Significant Change Delta parameters.
iii
Configure the parameters in the Reference Queue panel:
Note 1 — You can select all options for a parameter by clicking on the
Select All button beside the counters.
Note 2 — You can deselect all options for a parameter by clicking on
the Deselect All button beside the counters.
•
•
•
69-8
All Queues
Ingress Counters
Egress Counters
iv
If the All Queues parameter is enabled, go to step 7 vii.
v
Click on the Select button below the All Queues parameter to choose a queue
to monitor for the significant change. The Select Queue form opens.
vi
Select a queue in the list and click on the OK button. The Select Queues form
closes and the queue ID is displayed on the form.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
vii
Configure the parameters in the Reference Override panel:
Note 1 — You can select all options for a parameter by clicking on the
Select All button beside the counters.
Note 2 — You can deselect all options for a parameter by clicking on
the Deselect All button beside the counters.
•
•
•
All Overrides
Ingress Counters
Egress Counters
viii If you do not enable the All Overrides parameter, go to step 9.
9
10
ix
Click on the Select button below the All Overrides parameter to choose an
override counter to monitor for the significant change. The Select Override
form opens.
x
Select an override in the list and click on the OK button. The Select Override
form closes and the override ID is displayed on the form.
Perform the following steps.
i
Click on the Queue Counter Config tab button.
ii
Click on the Add button. The CustomQueueConfig (Create) form opens.
iii
Configure the ID parameter.
iv
Configure the Counters parameter in the Ingress panel.
v
Configure the Counters parameter in the Egress panel.
vi
Click on the OK button. A dialog box appears.
vii
Click on the OK button. The Accounting Policy (Edit) form reappears.
Perform the following steps.
i
Click on the Override Counter Config tab button.
ii
Click on the Add button. The CustomOverrideConfig (Create) form opens.
iii
Configure the ID parameter.
iv
Configure the Counters parameter in the Ingress panel.
v
Configure the Counters parameter in the Egress panel.
vi
Click on the OK button. A dialog box appears.
vii
Click on the OK button. The Accounting Policy (Edit) form reappears.
11
Click on the General tab button if the General tab is not currently displayed.
12
Click on the Switch Mode button. A dialog box appears.
13
Click on the Yes button. The configuration mode changes from Draft to Released.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-9
69 — Accounting statistics collection
14
Close the Accounting Policy form. The Manage Accounting Policies form
reappears.
15
Close the Manage Accounting Policies form.
Procedure 69-3 To configure a statistics policy for accounting
statistics on a SAP or an SDP
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of accounting statistics on a SAP or an SDP.
1
Choose Manage→Services from the 5620 SAM main menu. The Manage Services
form opens.
2
Specify a filter to create a filtered list of services and click on the Search button.
A list of services is displayed.
3
Select a service in the list and click on the Properties button. The service
properties form opens with the General tab displayed.
4
Click on one of the following tab buttons:
Note — The tab buttons that are displayed depend on the type of
service that is chosen.
•
•
•
•
L2 Access Interfaces
L3 Access Interfaces
Mesh SDP Bindings
Spoke SDP Bindings
The properties form for the object opens.
69-10
5
Click on the Statistics tab button.
6
Choose a statistics class from the object drop-down list.
7
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
8
Configure the parameters:
•
•
•
Retention Time (hours)
Administrative State
Threshold Reporting State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected statistics class type are not stored
in the 5620 SAM database. The statistics cannot be viewed in the
5620 SAM GUI or exported to a 5620 SAM-O client using find or
findToFile operations. However, if a 5620 SAM-O client registers using
registerLogToFile, the accounting statistics data is exported to files.
9
Click on the Thresholds tab button. The Thresholds tab contains a threshold
parameter for each counter in the statistics class.
10
Configure the threshold parameters. When a statistics counter threshold is
exceeded, the 5620 SAM raises a threshold-crossing alarm. See the statistics
tables in the appendices for a description of each statistics counter.
11
Click on the OK button. A dialog box appears.
12
Click on the Yes button. The Statistics Policy form closes and the object properties
form reappears.
13
Close the object properties form. The service properties form reappears.
14
Click on the OK button. A dialog box appears.
15
Click on the Yes button. The service properties form closes and the Manage
Services form reappears.
16
Close the Manage Services form.
Procedure 69-4 To configure a statistics policy for accounting
statistics on a network interface
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of accounting statistics on a network interface.
1
Choose Routing from the navigation tree view selector.
2
Navigate to the required network interface.
3
Right-click on the interface icon and choose Properties from the contextual menu.
The Network Interface (Edit) form opens with the General tab displayed.
4
Click on the Statistics tab button.
5
Choose a statistics class from the object drop-down list.
6
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-11
69 — Accounting statistics collection
7
Configure the parameters:
•
•
•
Retention Time (hours)
Administrative State
Threshold Reporting State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected statistics class type are not stored
in the 5620 SAM database. The statistics cannot be viewed in the
5620 SAM GUI or exported to a 5620 SAM-O client using find or
findToFile operations. However, if a 5620 SAM-O client registers using
registerLogToFile, the accounting statistics data is exported to files.
8
Click on the Thresholds tab button. The Thresholds tab contains a threshold
parameter for each counter in the statistics class.
9
Configure the threshold parameters. When a statistics counter threshold is
exceeded, the 5620 SAM raises a threshold-crossing alarm. See the statistics
tables in the appendices for a description of each statistics counter.
10
Click on the OK button. A dialog box appears.
11
Click on the Yes button. The Statistics Policy form closes and the Network
Interface form reappears.
12
Close the Network Interface form.
Procedure 69-5 To configure a statistics policy for accounting
statistics on a subscriber
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of accounting statistics on a subscriber.
69-12
1
Choose Manage→Residential Subscribers from the 5620 SAM main menu. The
Manage Residential Subscribers form opens.
2
Choose Residential Subscriber Instance from the object drop-down list and click
on the Search button. A list of residential subscriber instances is displayed.
3
Select a residential subscriber instance in the list and click on the Properties
button. The Residential Subscriber Instance form opens with General tab
displayed.
4
Click on the Statistics tab button.
5
Choose a statistics class from the object drop-down list.
6
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
7
Configure the parameters:
•
•
•
Retention Time (hours)
Administrative State
Threshold Reporting State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected statistics class type are not stored
in the 5620 SAM database. The statistics cannot be viewed in the
5620 SAM GUI or exported to a 5620 SAM-O client using find or
findToFile operations. However, if a 5620 SAM-O client registers using
registerLogToFile, the accounting statistics data is exported to files.
8
Click on the Thresholds tab button. The Thresholds tab contains a threshold
parameter for each counter in the statistics class.
9
Configure the threshold parameters. When a statistics counter threshold is
exceeded, the 5620 SAM raises a threshold-crossing alarm. See the statistics
tables in the appendices for a description of each statistics counter.
10
Click on the OK button. A dialog box appears.
11
Click on the Yes button. The Statistics Policy form closes and the Residential
Subscriber Instance form reappears.
12
Close the Residential Subscriber Instance form.
13
Close the Manage Residential Subscriber Instance form.
Procedure 69-6 To configure a statistics policy for AA accounting
statistics on a subscriber
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of AA accounting statistics on a subscriber.
1
Choose Manage→Residential Subscribers from the 5620 SAM main menu. The
Manage Residential Subscribers form opens.
2
Choose Residential Subscriber Instance from the object drop-down list and click
on the Search button. A list of residential subscriber instances is displayed.
3
Select a residential subscriber instance in the list and click on the Properties
button. The Residential Subscriber Instance form opens with General tab
displayed.
4
Click on the Statistics tab button.
5
Choose an AA statistics class from the object drop-down list.
6
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-13
69 — Accounting statistics collection
7
Configure the parameters:
•
•
Retention Time (hours)
Administrative State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected statistics class type are not stored
in the 5620 SAM database. The statistics cannot be viewed in the
5620 SAM GUI or exported to a 5620 SAM-O client using find or
findToFile operations. However, if a 5620 SAM-O client registers using
registerLogToFile, the accounting statistics data is exported to files.
8
Click on the OK button. A dialog box appears.
9
Click on the Yes button. The Statistics Policy form closes and the Residential
Subscriber Instance form reappears.
10
Close the Residential Subscriber Instance form.
11
Close the Manage Residential Subscribers form.
Procedure 69-7 To configure a statistics policy for an AA accounting
statistics application
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of AA accounting statistics on an AA application.
69-14
1
Choose Policies→Application Assurance from the 5620 SAM main menu. The
Manage Application Assurance Policies form opens.
2
Choose Application Group Policy from the object drop-down list and click on the
Search button. A list of application group policies is displayed.
3
Select a policy in the list and click on the Properties button. The global Application
Assurance Group Policy (Edit) form opens with the General tab displayed.
4
Click on the Local Definitions tab button.
5
Select a local policy definition in the list and click on the Properties button. The
local Application Assurance Group Policy (Edit) form opens with the General tab
displayed.
6
Click on the Applications tab button.
7
Select an application in the list and click on the Properties button. The Application
(Edit) form opens with the General tab displayed.
8
Click on the Statistics tab button.
9
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
10
Configure the parameters:
•
•
Retention Time (hours)
Administrative State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected application are not stored in the
5620 SAM database. The statistics cannot be viewed in the 5620 SAM GUI
or exported to a 5620 SAM-O client using find or findToFile operations.
However, if a 5620 SAM-O client registers using registerLogToFile, the
accounting statistics data is exported to files.
11
Click on the OK button. A dialog box appears.
12
Click on the Yes button. The Statistics Policy form closes and the Application (Edit)
form reappears.
13
Close the Application (Edit) form.
14
Close the local Application Assurance Group Policy (Edit) form.
15
Close the global Application Assurance Group Policy (Edit) form.
16
Close the Manage Application Assurance Policies form.
Procedure 69-8 To configure a statistics policy for an AA accounting
statistics application group
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of AA accounting statistics on an AA application
group.
1
Choose Policies→Application Assurance from the 5620 SAM main menu. The
Manage Application Assurance Policies form opens.
2
Choose Application Group Policy from the object drop-down list and click on the
Search button. A list of application group policies is displayed.
3
Select a policy in the list and click on the Properties button. The global Application
Assurance Group Policy (Edit) form opens with the General tab displayed.
4
Click on the Local Definitions tab button.
5
Select a local policy definition in the list and click on the Properties button. The
local Application Assurance Group Policy (Edit) form opens with the General tab
displayed.
6
Click on the Application Groups tab button.
7
Select an application group in the list and click on the Properties button. The
Application Group (Edit) form opens with the General tab displayed.
8
Click on the Statistics tab button.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-15
69 — Accounting statistics collection
9
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
10
Configure the parameters:
•
•
Retention Time (hours)
Administrative State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected application group are not stored
in the 5620 SAM database. The statistics cannot be viewed in the
5620 SAM GUI or exported to a 5620 SAM-O client using find or
findToFile operations. However, if a 5620 SAM-O client registers using
registerLogToFile, the accounting statistics data is exported to files.
11
Click on the OK button. A dialog box appears.
12
Click on the Yes button. The Statistics Policy form closes and the Application
Group (Edit) form reappears.
13
Close the Application Group (Edit) form.
14
Close the local Application Assurance Group Policy (Edit) form.
15
Close the global Application Assurance Group Policy (Edit) form.
16
Close the Manage Application Assurance Policies form.
Procedure 69-9 To configure a statistics policy for an AA accounting
statistics protocol
Perform this procedure to configure a policy that specifies the 5620 SAM database
storage criteria for a specific class of AA accounting statistics on an AA protocol.
69-16
1
Choose Policies→Application Assurance from the 5620 SAM main menu. The
Manage Application Assurance Policies form opens.
2
Choose Local from the Policy scope drop-down menu.
3
Specify a device by clicking on the Select button and choosing a device from the
list.
4
Choose Application Assurance Protocol from the object drop-down list and click
on the Search button. A list of protocols is displayed.
5
Select a protocol in the list and click on the Properties button. The Application
Assurance Protocol (Edit) form opens with General tab displayed.
6
Click on the Statistics tab button.
7
Click on the Statistics Policies button and choose Statistics Policy from the
drop-down menu. The Statistics Policy form opens with the General tab displayed.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
69 — Accounting statistics collection
8
Configure the parameters:
•
•
Retention Time (hours)
Administrative State
Note — If the Administrative State parameter is set to Down,
accounting statistics for the selected protocol are not stored in the
5620 SAM database. The statistics cannot be viewed in the 5620 SAM GUI
or exported to a 5620 SAM-O client using find or findToFile operations.
However, if a 5620 SAM-O client registers using registerLogToFile, the
accounting statistics data is exported to files.
9
Click on the OK button. A dialog box appears.
10
Click on the Yes button. The Statistics Policy form closes and the Application
Assurance Protocol (Edit) form reappears.
11
Close the Application Assurance Protocol (Edit) form.
12
Close the Manage Application Assurance Policies form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
69-17
69 — Accounting statistics collection
69-18
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
70 — Server performance statistics
collection
70.1 Server performance statistics collection overview
70-2
70.2 Workflow for server performance statistics collection
70-2
70.3 Server performance statistics collection procedures list
70.4 Server performance statistics collection procedures
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
70-2
70-2
70-1
70 — Server performance statistics collection
70.1
Server performance statistics collection overview
Server performance statistics are collected from the 5620 SAM main servers in a
5620 SAM system. To collect server performance statistics, you need to create and
apply the following policies:
• statistics policy
• server performance collection policy
See chapter 67 for more information about the policies.
70.2
70.3
Workflow for server performance statistics collection
1
Configure the statistics policy associated with the statistics data. See
Procedure 70-1 for more information.
2
Configure the server performance collection policy that is associated with the
statistics data. See Procedure 70-2 for more information.
3
Delete statistics records, as required. See Procedure 70-3 for more information.
Server performance statistics collection procedures list
Table 70-1 lists the procedures to collect server performance statistics.
Table 70-1 Server performance statistics collection procedures list
70.4
Procedure
Purpose
To configure a statistics policy for server
performance statistics
Specify how the 5620 SAM manages server
performance statistics.
To configure a statistics collection policy for
server performance statistics
Specify polling and collection policies for server
performance statistics classes and counters.
To delete statistics records
Delete collected statistics records.
Server performance statistics collection procedures
Use the following procedures to configure the collection of server performance
statistics.
70-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
70 — Server performance statistics collection
Procedure 70-1 To configure a statistics policy for server
performance statistics
Perform this procedure to create a policy that specifies the storage criteria for
5620 SAM server performance statistics. You can create one statistics policy for each
type of statistics counter.
1
Choose Tools→Statistics→Server Performance Statistics from the 5620 SAM main
menu. The Server Performance Statistics form opens.
2
Choose one of the following statistics classes from the object drop-down list:
•
•
•
•
•
Alarm Rate (SAM Performance Statistics)—counters related to 5620 SAM alarms
Node Resync (SAM Performance Statistics)—counters related to NE
resynchronizations
SNMP Trap (SAM Performance Statistics)—counters related to NE SNMP traps
Server Memory (SAM Performance Statistics)—counters related to 5620 SAM
server memory usage
Statistics Collection (SAM Performance Statistics)—counters related to
accounting and performance statistics collection
3
Click on the Statistics Policy button. The Statistics Policy form opens with the
General tab displayed.
4
Configure the parameters:
•
•
•
Retention Time (hours)
Administrative State
Threshold Reporting State
5
Click on the Thresholds tab button. The Thresholds tab contains a threshold
parameter for each counter in the statistics class.
6
Configure the threshold parameters. When a statistics counter threshold is
exceeded, the 5620 SAM raises a threshold-crossing alarm. See section 169.1 in
the 5620 SAM Parameter Guide for a description of each threshold parameter.
7
Click on the OK button. A dialog box appears.
8
Click on the Yes button. The Statistics Policy form closes and the Server
Performance Statistics form reappears.
9
Close the Server Performance Statistics form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
70-3
70 — Server performance statistics collection
Procedure 70-2 To configure a statistics collection policy for server
performance statistics
Perform this procedure to create a policy for the collection of 5620 SAM server
performance statistics. You can create one collection policy for each statistics policy.
1
Choose Tools→Statistics→Server Performance Statistics from the 5620 SAM main
menu. The Server Performance Statistics form opens.
2
Choose one of the following statistics classes from the object drop-down list:
•
•
•
•
•
3
Click on the Collection Policy button. The Collection Policy form opens.
4
Configure the parameters:
•
•
•
70-4
Alarm Rate (SAM Performance Statistics)—counters related to 5620 SAM alarms
Node Resync (SAM Performance Statistics)—counters related to NE
resynchronizations
SNMP Trap (SAM Performance Statistics)—counters related to NE SNMP traps
Server Memory (SAM Performance Statistics)—counters related to 5620 SAM
server memory usage
Statistics Collection (SAM Performance Statistics)—counters related to
accounting and performance statistics collection
Administrative State
Polling Synchronization Time
Collection Interval
5
Click on the OK button. A dialog box appears.
6
Click on the Yes button. The Collection Policy form closes and the Server
Performance Statistics form reappears.
7
Close the Server Performance Statistics form.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
70 — Server performance statistics collection
Procedure 70-3 To delete statistics records
Perform this procedure to remove one or more server performance statistics records
from the 5620 SAM database.
1
Choose Tools→Statistics→Server Performance Statistics from the 5620 SAM main
menu. The Server Performance Statistics form opens.
2
Choose one of the following statistics classes from the object drop-down list:
•
•
•
•
•
Alarm Rate (SAM Performance Statistics)—counters related to 5620 SAM alarms
Node Resync (SAM Performance Statistics)—counters related to NE
resynchronizations
SNMP Trap (SAM Performance Statistics)—counters related to NE SNMP traps
Server Memory (SAM Performance Statistics)—counters related to 5620 SAM
server memory usage
Statistics Collection (SAM Performance Statistics)—counters related to
accounting and performance statistics collection
3
Click on the Statistics Policy button. The Statistics Policy form opens with the
General tab displayed.
4
Click on the Purge Statistics Records button. The Statistics Policy filter form
opens.
5
Use the filter form to narrow the search for specific statistics records.
6
Click on the OK button. A dialog box appears.
7
Click on the Yes button. The Statistics Policy filter form closes, and the records
are deleted from the database. The Statistics Policy form appears.
8
Close the Statistics Policy form. The Server Performance Statistics form
reappears.
9
Close the Server Performance Statistics form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
70-5
70 — Server performance statistics collection
70-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Statistics presentation
71 — Statistics presentation overview
72 — Viewing statistics
73 — Graphing statistics
74 — Using the 5620 SAM-O to collect statistics
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
71 — Statistics presentation overview
71.1 Statistics presentation
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
71-2
December 2009
71-1
71 — Statistics presentation overview
71.1
Statistics presentation
You can view all statistics types that the 5620 SAM supports in tables or graphs.
Tables list specific values, and the table data can be sorted, filtered, and exported to
files in different formats. Graphs help to identify trends, and can display multiple
statistics counters simultaneously. A graph can have multiple independently scaled
axes that allow a 5620 SAM operator to visually compare statistics with high
numbers, such as throughput statistics, to statistics with very low numbers, such as
dropped packet statistics. You can export graphs to files using different file formats.
There are two methods of specifying the statistics to present in a table or graph.
• bottom-up method—applies to performance and accounting statistics, and
involves navigating to the object on which the statistics are collected, such as a
SAP, SDP, or network port
• top-down method—applies to all statistics types, and involves opening a browser
form using the Tools→Statistics Browser option in the 5620 SAM main menu
You can display statistics from multiple objects in one list using a filter, choose
a specific statistics type, filter on a specific object, and view the statistics in a
table.
Tabular statistics view
Statistics for a single object are viewable in the Statistics tab of the object properties
form. Each displayed statistics class corresponds to a MIB table or to an accounting
file on the NE. When a collection policy is applied, the list is populated with rows of
statistics that are collected from the MIBs or accounting files specified in the policy.
You can also collect network and server performance statistics on demand by
clicking on the Collect button in the Statistics tab. The MIB associated with the
selected statistics type is polled and one row appears in the statistics list. The record
type is On-Demand, which indicates that the row is not collected using a collection
policy.
The Collect All button collects one on-demand statistics record for each statistic type
that the object supports. This is useful for collecting different types of statistics at the
same time.
On-demand collection is not available for accounting statistics. Accounting statistics
are available only in the 5620 SAM after an NE transfers an accounting statistics file
to the 5620 SAM.
The top section of a statistics tab contains a drop-down menu of statistics classes for
the object, and a filter that you can configure to limit the number of listed statistics,
for example, statistics collected during a specific time period. You can open a listed
entry to display a Statistics Record form that lists each counter and value, and
contains details about the record collection.
You can quickly sort a list of statistics by clicking on a list column heading, for
example, Time Captured or Record Type, and can customize the sorting by
right-clicking on the list heading and choosing Show Sorting from the contextual
menu.
You can export the statistics list to a file by right-clicking on the list heading and
choosing Save to File from the contextual menu.
71-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
71 — Statistics presentation overview
Graphical statistics view
Statistics can be viewed in a graph using the 5620 SAM statistics plotter. The plotter
can display multiple performance, accounting, and server performance statistics
simultaneously using dual axes. The plotter also provides a numerical value for each
point on the graph.
Each 5620 SAM client can open up to five statistics plotters, and each plotter can
simultaneously plot up to four counters. Plotters can have independent Y axes on the
left and right sides of a graph, and any counter can be assigned to one of the Y axes.
A plotter can plot real-time or historical statistics. Historical plots use statistics from
earlier collections that are stored in the 5620 SAM database. The plotter
automatically plots all of the stored values for the specified counter. Real-time plots
collect statistics while the plotter window is open and plot the data as it is collected.
For real-time statistics, when multiple 5620 SAM clients each have multiple open
plotters that are displaying multiple counters, a high volume of statistics is collected
from the NEs. If the collection for many of the plotters is from the same NE, the NE
is polled independently for each plotter, which may affect performance. You can use
a scope of command role to limit plotter access to specific 5620 SAM user groups.
Performance statistics are collected from NE MIBs and converted to periodic values.
Accounting statistics are collected, filtered, as required, for example, by queue ID for
network ingress objects, and converted to periodic values. The 5620 SAM calculates
periodic values by subtracting the previous counter value from the current counter
value. Periodic data is typically more useful than raw counter values for
troubleshooting and trend analysis.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
71-3
71 — Statistics presentation overview
71-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
72.1 Viewing statistics overview
72-2
72.2 Workflow for viewing statistics
72.3 Viewing statistics menus
72-2
72-2
72.4 Viewing statistics procedures list
72.5 Viewing statistics procedures
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
72-2
72-3
December 2009
72-1
72 — Viewing statistics
72.1
Viewing statistics overview
Statistics can be viewed as numerical data in a table, which is useful for obtaining
raw counter values. The tabular data can be sorted, filtered, and exported to files in
different formats.
AA statistics can be viewed from the Statistics tab of a local AA policy object, such
as an application, application group, or protocol.
72.2
Workflow for viewing statistics
1
Monitor on-demand performance statistics. See Procedure 72-1 for more
information.
2
Monitor statistics for sets of objects. See Procedure 72-2 for more information.
3
Monitor scheduled collection for the following statistics types, as required:
•
•
•
•
•
4
72.3
performance—see Procedure 72-4 for more information
service accounting—see Procedure 72-6 for more information
specific-object—see Procedure 72-3 for more information
subscriber accounting—see Procedure 72-7 for more information
AA accounting—see Procedures 72-7 through 72-11 for more information
Monitor 5620 SAM server performance statistics using the GUI. See Procedure 72-5
for more information.
Viewing statistics menus
Table 72-1 lists the statistics data viewing menus and their functions.
Table 72-1 Statistics data viewing menus
72.4
Menu option
Function
Tools→Statistics Browser
To view statistics records and policies
Manage→Services
To view service accounting statistics
Manage→Residential Subscribers
To view subscriber accounting statistics and AA
accounting statistics per subscriber
Policies→Application Assurance
To view AA accounting statistics
Tools→Statistics→Server Performance
Statistics
To view server performance statistics
Viewing statistics procedures list
Table 72-2 lists the procedures for viewing statistics data.
72-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
Table 72-2 Statistics data viewing procedures list
72.5
Procedure
Purpose
To view on-demand statistics
Display on-demand statistics.
To view statistics for a set of objects
Display statistics for multiple objects.
To view performance statistics
Display scheduled performance statistics.
To view service accounting statistics
Display scheduled service accounting statistics.
To view network accounting statistics
Display scheduled network accounting statistics.
To view subscriber accounting statistics
Display scheduled subscriber accounting
statistics.
To view per-subscriber AA accounting statistics
Display scheduled AA accounting statistics for a
subscriber.
To view AA accounting statistics for an
application
Display scheduled AA accounting statistics for an
application.
To view AA accounting statistics for an
application group
Display scheduled AA accounting statistics for an
application group.
To view AA accounting statistics for a protocol
Display scheduled AA accounting statistics for a
protocol.
To view server performance statistics
Display server performance statistics.
Viewing statistics procedures
Use the following procedures to view statistics data.
Procedure 72-1 To view on-demand statistics
Perform this procedure to collect and display the statistics values in a current statistics
record.
1
Open the properties form of the object for which you want to view statistics. The
General tab is displayed.
2
Click on the Statistics tab button.
3
Choose a statistics class from the object drop-down list.
Note — The Collect and Collect All buttons are not displayed when you
choose a statistics class that does not support on-demand statistics
collection.
4
Specify a filter to create a filtered list of statistics records, if required.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
72-3
72 — Viewing statistics
5
Perform one of the following.
a
Click on the Collect button to collect the statistics for only the specified
class.
b
Click on the Collect All button to collect statistics for all classes.
The statistics records are displayed in a list.
6
Identify a statistics record to view.
7
Perform one of the following.
8
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
Close the object properties form.
Procedure 72-2 To view statistics for a set of objects
Perform this procedure to display the statistics data and collection criteria for a one or
more statistics classes.
72-4
1
Choose Tools→Statistics Browser from the 5620 SAM main menu. The Browse
Statistics form opens.
2
Configure the Statistics Type parameter.
3
Choose a statistics class from the object drop-down list. Choose ALL to select all
statistics classes.
4
Specify a filter to create a filtered list of entries, if required.
5
Click on the Search button. A list of entries is displayed.
6
Identify an entry to view.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
7
8
Perform one of the following.
a
Scroll horizontally to view the values that the entry contains.
b
Open the entry to view it.
i
Select the entry and click on the Properties button. The appropriate
form opens, based on the Statistics Type parameter setting.
ii
View the form contents.
iii
Close the form.
Close the Browse Statistics form.
Procedure 72-3 To view network accounting statistics
Perform this procedure to display network-based accounting statistics data in a table.
1
Choose Manage→Service Tunnels from the 5620 SAM main menu. The Manage
Service Tunnels form opens.
2
Specify a filter to create a filtered list of service tunnels and click on the Search
button. A list of service tunnels is displayed.
3
Select a service tunnel in the list and click on the Properties button. The service
tunnel properties form opens with the General tab displayed.
4
Click on the Statistics tab button.
5
Choose a statistics class from the object drop-down list.
6
Specify a filter to create a filtered list of statistics classes, if required.
7
Click on the Search button. A list of statistics records is displayed.
8
Identify a statistics record to view.
9
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
72-5
72 — Viewing statistics
10
Close the service tunnel properties form.
11
Close the Manage Service Tunnels form.
Procedure 72-4 To view performance statistics
Perform this procedure to display performance statistics data in a table.
1
Right-click on an object in the navigation tree and choose Properties from the
contextual menu. The properties form for the object opens with the General tab
displayed.
2
Click on the Statistics tab button.
3
Choose a statistics class from the object drop-down list.
Note — The Collect and Collect All buttons are not displayed when you
choose a statistics class that does not support on-demand statistics
collection.
4
Specify a filter to create a filtered list of statistics classes.
5
Perform one of the following.
a
Click on the Collect button to collect the statistics for only the specified
class.
b
Click on the Collect All button to collect statistics for all classes.
The statistics records are displayed in a list.
6
Identify a statistics record to view.
7
Perform one of the following.
8
72-6
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
Close the object properties form.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
Procedure 72-5 To view server performance statistics
Perform this procedure to display 5620 SAM server performance statistics data in a
table.
1
Choose Tools→Statistics→Server Performance Statistics from the 5620 SAM main
menu. The Server Performance Statistics form opens.
2
Choose one of the following statistics classes from the object drop-down list:
•
•
•
•
•
Alarm Rate (SAM Performance Statistics)—counters related to 5620 SAM alarms
Node Resync (SAM Performance Statistics)—counters related to NE
resynchronizations
SNMP Trap (SAM Performance Statistics)—counters related to NE SNMP traps
Server Memory (SAM Performance Statistics)—counters related to 5620 SAM
server memory usage
Statistics Collection (SAM Performance Statistics)—counters related to
accounting and performance statistics collection
3
Specify a filter to create a filtered list of statistics records, if required.
4
Perform one of the following.
a
Click on the Search button to list statistics records for scheduled collections
of the statistics class.
b
Click on the Collect button to perform an on-demand collection for the
statistics class.
5
Identify a statistics record to view.
6
Perform one of the following.
7
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
Close the Server Performance Statistics form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
72-7
72 — Viewing statistics
Procedure 72-6 To view service accounting statistics
Perform this procedure to display service-based accounting statistics data in a table.
72-8
1
Choose Manage→Services from the 5620 SAM main menu. The Manage Services
form opens.
2
Specify a filter to create a filtered list of services and click on the Search button.
A list of services is displayed.
3
Select a service in the list and click on the Properties button. The service
properties form opens with the General tab displayed.
4
Click on the L2 Access Interfaces or L3 Access Interfaces tab button, as required,
to display a list of access interfaces.
5
Select an interface in the list and click on the Properties button. The appropriate
access interface properties form opens with the General tab displayed.
6
Click on the Statistics tab button.
7
Choose a statistics class from the object drop-down list.
8
Specify a filter to create a filtered list of statistics classes, if required.
9
Click on the Search button. A list of statistics records is displayed.
10
Identify a statistics record to view.
11
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
12
Close the access interface properties form.
13
Close the service properties form.
14
Close the Manage Services form.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
Procedure 72-7 To view subscriber accounting statistics
Perform this procedure to display subscriber-related accounting statistics data in a
table.
1
Choose Manage→Residential Subscribers from the 5620 SAM main menu. The
Manage Residential Subscribers form opens.
2
Choose Residential Subscriber Instance from the object drop-down list and click
on the Search button. A list of residential subscriber instances is displayed.
3
Select a residential subscriber instance in the list and click on the Properties
button. The Residential Subscriber Instance properties form opens with the
General tab displayed.
4
Click on the Statistics tab button.
5
Choose a statistics class from the object drop-down list.
6
Specify a filter to create a filtered list of statistics classes, if required.
7
Click on the Search button. A list of statistics records is displayed.
8
Identify a statistics record to view.
9
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
10
Close the Residential Subscriber Instance properties form.
11
Close the Manage Residential Subscribers form.
Procedure 72-8 To view per-subscriber AA accounting statistics
Perform this procedure to display, in a table, the AA-related accounting statistics data
for a subscriber.
1
Choose Manage→Residential Subscribers from the 5620 SAM main menu. The
Manage Residential Subscribers form opens.
2
Choose Residential Subscriber Instance from the object drop-down list and click
on the Search button. A list of residential subscriber instances is displayed.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
72-9
72 — Viewing statistics
3
Select a residential subscriber instance in the list and click on the Properties
button. The Residential Subscriber Instance properties form opens with the
General tab displayed.
4
Click on the Statistics tab button.
5
Choose an AA statistics class from the object drop-down list.
6
Specify a filter to create a filtered list of statistics classes, if required.
7
Click on the Search button. A list of statistics records is displayed.
8
Identify a statistics record to view.
9
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
10
Close the Residential Subscriber Instance properties form.
11
Close the Manage Residential Subscribers form.
Procedure 72-9 To view AA accounting statistics for an application
Perform this procedure to display, in a table, the AA-related accounting statistics data
for an application.
72-10
1
Choose Policies→Application Assurance from the 5620 SAM main menu. The
Manage Application Assurance Policies form opens.
2
Choose Application Assurance Group Policy from the object drop-down list and
click on the Search button. A list of AA group policies is displayed.
3
Select a policy in the list and click on the Properties button. The global Application
Assurance Group Policy form opens with the General tab displayed.
4
Click on the Local Definitions tab.
5
Select a local policy definition in the list and click on the Properties button. The
Application Assurance Group Policy form opens with the General tab displayed.
6
Click on the Applications tab button.
7
Choose an application in the list and click on the Properties button. The
Application properties form opens.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
8
Click on the Statistics tab button.
9
Specify a filter to create a filtered list of statistics classes, if required.
10
Click on the Search button. A list of statistics records is displayed.
11
Identify a statistics record to view.
12
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
13
Close the Application properties form.
14
Close the local Application Assurance Group Policy form.
15
Close the global Application Assurance Group Policy form.
16
Close the Manage Application Assurance Policies form.
Procedure 72-10 To view AA accounting statistics for an application
group
Perform this procedure to display, in a table, the AA-related accounting statistics data
for an application group.
1
Choose Policies→Application Assurance from the 5620 SAM main menu. The
Manage Application Assurance Policies form opens.
2
Choose Application Assurance Group Policy from the object drop-down list and
click on the Search button. A list of AA group policies is displayed.
3
Select a policy in the list and click on the Properties button. The global Application
Assurance Group Policy form opens with the General tab displayed.
4
Click on the Local Definitions tab.
5
Select a local policy definition in the list and click on the Properties button. The
local Application Assurance Group Policy form opens with the General tab
displayed.
6
Click on the Application Groups tab button.
7
Choose an application group in the list and click on the Properties button. The
Application Group properties form opens.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
72-11
72 — Viewing statistics
8
Click on the Statistics tab button.
9
Specify a filter to create a filtered list of statistics classes, if required.
10
Click on the Search button. A list of statistics records is displayed.
11
Identify a statistics record to view.
12
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
13
Close the Application Group properties form.
14
Close the local Application Assurance Group Policy form.
15
Close the global Application Assurance Group Policy form.
16
Close the Manage Application Assurance Policies form.
Procedure 72-11 To view AA accounting statistics for a protocol
Perform this procedure to display, in a table, the AA-related accounting statistics data
for a protocol.
72-12
1
Choose Policies→Application Assurance from the 5620 SAM main menu. The
Manage Application Assurance Policies form opens.
2
Choose Local from the Policy scope drop-down menu.
3
Specify a device by clicking on the Select button and choosing a device from the
list.
4
Choose Application Assurance Protocol from the object drop-down list and click
on the Search button. A list of protocols is displayed.
5
Select a protocol in the list and click on the Properties button. The Application
Assurance Protocol (Edit) form opens with General tab displayed.
6
Click on the Statistics tab button.
7
Specify a filter to create a filtered list of statistics records, if required.
8
Click on the Search button. A list of statistics records is displayed.
9
Identify a statistics record to view.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
72 — Viewing statistics
10
Perform one of the following.
a
Scroll horizontally to view the statistics counter values for the statistics
record.
b
Open the statistics record to view it.
i
Select the statistics record and click on the Properties button. The
Statistics Record form opens.
ii
View the statistics record.
iii
Click on the Close button to close the Statistics Record form.
11
Close the Application Assurance Protocol (Edit) form.
12
Close the Manage Application Assurance Policies form.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
72-13
72 — Viewing statistics
72-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
73 — Graphing statistics
73.1 Graphing statistics overview
73-2
73.2 Workflow for graphing statistics
73.3 Graphing statistics menus
73-5
73-5
73.4 Graphing statistics procedures list
73.5 Graphing statistics procedures
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
73-5
73-5
December 2009
73-1
73 — Graphing statistics
73.1
Graphing statistics overview
The 5620 SAM client GUI can display real-time and historical statistics line graphs
of many statistics types. You can plot multiple counters in a graph, and can have
multiple graphs open at one time. Figure 73-1 shows the 5620 SAM Statistics Plotter
form.
Figure 73-1 5620 SAM Statistics Plotter
Configuration
panel
Detail
panel
Overview
panel
Data list
panel
19736
Statistics Plotter
The 5620 SAM Statistics Plotter allows you to plot counter values for real-time or
historical statistics. The Statistics Plotter contains the following panels:
• configuration panel—allows you to enter the counters to plot
• detail panel—contains the plotted graph points and axes
• overview panel—provides an overview of the entire data range of the statistics
available for plotting
• data panel—presents the graph data in tabular form
You can maximize or minimize a panel by clicking on the up or down arrow on the
left side of the divider bar between it and the neighboring panel.
73-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
73 — Graphing statistics
Configuration panel
The configuration panel identifies the objects and statistics counters in a graph. You
can enter up to four counters in this panel. If more than one counter from the same
monitored object is required, you can click on the Duplicate button and choose the
new counter and class. After you choose the counters, you can close the panel to
increase the space available for the graph panels. The Configuration panel contains
the following columns:
• Marker—displays the data points as markers in the detail panel
• Plot Name—identifies the plots in the graph
• Y Axis—allows you to choose Y Axis 1 or Y Axis 2. See “Choosing the Y-axis”
in this section for more information
• Monitored Object—lists the monitored objects
• Statistics Group—allows you to choose the statistics class for the object
• Statistics Counter—allows you to choose the statistics counter for the object.
See “Statistics counters” in this section for more information
Detail panel
The detail panel contains the plotted statistics line graphs. The panel can contain
historical or real-time graphs, but not both.
The real-time graphs start collection after the plotter opens. The historical graphs use
the data stored in the 5620 SAM database. You can zoom in and zoom out on a graph,
and for real-time statistics, you can enable or disable automatic scrolling.
See “Overview panel” in this section for more information.
You can enable or disable the markers and legend for a graph, and can save a graph
with or without the legend or markers. Markers are useful for identifying different
lines, for example, when a graph is printed in black and white. You can enable or
disable the X, Y1, and Y2 grid lines. The Y1 and Y2 grid lines are displayed only
when the corresponding Y axis is in use. See Procedures 73-2 and 73-3 for more
information.
Overview panel
The overview panel displays a high-level view of the plot data. The shaded box in
the panel contains the statistics that are displayed in the detail panel. When you
double-click on the box, you toggle automatic scrolling on or off. The box is green
when automatic scrolling is enabled, and red when it is disabled. You can click on
the box and drag it horizontally to change the display in the detail panel. When the
box is not selected and real-time statistics are being plotted, the box autoscrolls to
show the latest statistics. When automatic scrolling is disabled, the detail panel
remains in the location shown in the red box.
Data panel
The data panel displays a table of the collected statistics values. The statistics can be
saved in CSV or HTML format. See chapter 3 of the 5620 SAM User Guide for
information about using the contextual menu in the plot value list heading.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
73-3
73 — Graphing statistics
Choosing the Y-axis
The statistics graph can have one X axis and two Y axes. The X axis is a time scale
and the Y axis is the scale for data values. You can choose a Y axis from the
drop-down menu in the configuration panel.
One plotter can simultaneously plot up to four counters. Plotters can have
independent Y axes on the left and right of the graph. Any counters can be assigned
to a Y axis.
Statistics counters
Up to four statistics counters can be plotted in a graph.
A statistics counter name that includes the word “periodic” is a counter that records
the difference between the current and previous counter values. For example, when
the 5620 SAM polls the Transmitted Octets counter, it subtracts the counter value
from the previously polled value and stores the result in the Transmitted Octets
Periodic counter. A non-periodic statistics counter contains a cumulative value.
Real-time statistics data collection
The Statistics Plotter has a configurable default polling interval and a retention
period for real-time statistics collection. The retention period is configurable from
the User Preferences form. The retention period specifies how long the 5620 SAM
collects real-time statistics before it deletes the oldest sample. At a sampling rate of
10 s, the plotter stores 8640 samples per counter in one day. See Procedure 73-1 for
more information about configuring the global statistics graph parameters. You can
also specify a polling interval that differs from the default interval. See
Procedure 73-2 for more information.
The detail and data panels indicate when a real-time statistic is missing from a plot.
The detail panel plot markers in the plot list panel Markers column change from solid
to dark grey with the marker color as the border. The data panel displays N/A or Data
Missing instead of a data value.
• N/A indicates that events are skewed. For example, there is data event plot for
plot 1 and plot 2 at time T1, and a data event plot for plot 3 and plot 4 at time T2.
Accordingly, the table row displays N/A for plot 3 and plot 4 at time T1, and for
plot 1 and plot 2 at time T2. N/A is displayed whenever the same graph plots
counters from different classes or different NEs.
• Data Missing indicates an error during statistics collection. Data Missing is
displayed when an NE reports an error or when the polling interval elapses before
the response to a previous poll arrives.
You can remove a plot at any time during real-time statistics collection. The plot
disappears immediately from the detail panel and data panel. See Procedures 73-2
and 73-3 for more information.
73-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
73 — Graphing statistics
73.2
73.3
Workflow for graphing statistics
1
Configure the graph parameters. See Procedure 73-1 for more information.
2
Configure statistics collection for the equipment or logical object to be used as
the source of the statistics data to be graphed.
3
Create a real-time or historical statistics graph. See Procedure 73-2 for more
information.
4
Modify a real-time or historical statistics graph. See Procedure 73-3 for more
information.
Graphing statistics menus
Table 73-1 lists the statistics graph menus and functions.
Table 73-1 5620 SAM statistics graph menu
73.4
Menu option
Function
Application→User Preferences
Configure statistics graph user preferences.
Tools→Statistics Plotter→New Plot
Create and configure a statistics graph.
Tools→Statistics Plotter→Statistics Plotter (#)
Modify a statistics graph.
Graphing statistics procedures list
Table 73-2 lists the procedures necessary to perform statistics graphing tasks.
Table 73-2 5620 SAM statistics graphing procedures list
73.5
Procedure
Purpose
To configure the statistics graph parameters
Specify the default graph polling interval and
the retention time.
To configure and plot a statistics graph
Configure and plot a statistics graph.
To modify a statistics graph
Open and modify a statistics graph.
Graphing statistics procedures
Use the following procedures to perform statistics graphing tasks.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
73-5
73 — Graphing statistics
Procedure 73-1 To configure the statistics graph parameters
Perform this procedure to specify the global 5620 SAM parameters for graphing
statistics.
1
Choose Application→User Preferences from the 5620 SAM main menu. The User
Preferences form opens with the General tab displayed.
2
Click on the Statistics Plotter tab button.
3
Configure the parameters:
•
•
4
Default Polling Interval (Seconds)
Maximum Data Retention Time (Seconds)
Click on the OK button to close the User Preferences form and apply the changes.
The User Preferences form closes.
Procedure 73-2 To configure and plot a statistics graph
Perform this procedure to graphically plot statistics on the 5620 SAM GUI.
1
Perform one of the following.
a
b
73-6
Use the Copy to Clipboard function to plot a statistics graph.
i
Right-click on a monitored object in the navigation tree and choose
Copy to Clipboard from the contextual menu, or select a monitored
object from a form and click on the Copy to Clipboard button.
ii
Choose Tools→Statistics Plotter→New Plot from the 5620 SAM main
menu. The Statistics Plotter form opens.
iii
Click on the Paste from Clipboard button or right-click in the
configuration panel and choose Paste from Clipboard from the
contextual menu. The object appears in the configuration panel.
Use the Plotter button to plot a statistics graph.
i
Right-click on an object in the navigation tree and choose Properties
from the contextual menu. The properties form for the object opens
with the General tab displayed.
ii
Click on the Statistics tab button.
iii
Choose a statistics class from the object drop-down list, if required.
iv
Click on the Search button to view statistics record entries for
scheduled collections of the selected statistics class, or click on the
Collect button to perform an on-demand collection and view the
current statistics for the selected statistics class.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
73 — Graphing statistics
2
v
Choose a statistics record.
vi
Click on the Plotter button and choose New Plot from the drop-down
menu. The Statistics Plotter form opens.
Click on a plot in the Statistics Group column of the configuration panel and
choose a statistics group from the drop-down list.
Additional configurable columns may appear in the configuration panel if the
selected statistics group has filterable attributes. The columns allow you to filter
the statistics. Perform the following actions to configure a filter, as required.
•
•
Click on an up or down arrow in a column heading to specify an enumerated
entry such as a queue ID.
Double-click in a text-based column heading and type in a value.
Note — The 5620 SAM does not validate a typed entry. You must type
an entire entry correctly to generate the expected filter output.
3
Click on a plot in the Statistics Counter column of the configuration panel and
choose a statistics counter from the drop-down list.
4
Add a plot to the statistics plotter. You can duplicate the existing object or choose
a new object. If the same object is used, the statistics counter must be unique. If
a different object is used, the same statistics counter can be used for each object.
Note — A statistics graph can plot up to four statistics counters. The
statistics counters can all be the same when there are four different
objects. If only one object is used, each statistics counter must be
unique.
a
b
5
To add a plot using an object in the list:
i
Choose an object from the list and click on the Duplicate button. The
plot is duplicated in the list.
ii
Click on the new plot in the Statistics Group column and choose a
statistics group from the drop-down list.
iii
Click on the new plot in the Statistics Counter column and choose a
statistics counter from the drop-down list. The counter must be unique.
iv
Click on the Y Axis column and choose an axis from the drop-down list.
To add a statistics counter using a new object, repeat to steps 1 b to 4.
To add another plot to the plotter, repeat step 4. You can create up to four plots.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
73-7
73 — Graphing statistics
6
Perform one of the following.
Note 1 — Real-time statistics plotting is supported for network
performance, server performance, and MIB-based accounting statistics.
historical statistics plotting is supported for network performance,
server performance, and accounting statistics.
Note 2 — Each plot must be unique. The 5620 SAM deletes the older
plot if you attempt to create a duplicate a plot in this step.
a
To create a real-time statistics graph:
i
Choose a polling interval from the Real-time Polling Interval drop-down
menu, or enter a value between 10 and 3600.
ii
Click on the Real-time Plot button. The detail panel displays the plotted
statistics using the configured polling interval.
Note — You do not have to stop real-time statistics collection to add
or remove plots.
iii
b
7
Click on the stop button to pause the real-time statistics collection.
To create a graph using historical statistics, click on the Historical Plot
button. The statistics that are stored in the database are plotted in the detail
panel.
Perform one or more of the following to view details in the detail panel.
a
To display a tooltip for a plot, move the mouse pointer over the data points
in the detail panel. A tooltip identifies the plot number, the statistics
collection interval, and the statistics value at that interval.
b
To change the view displayed in the detail panel, click on the green box in
the overview panel and drag the box horizontally.
When the green box is not selected and real-time statistics are being
collected, the green box autoscrolls to display the latest statistics.
73-8
c
To turn off autoscrolling, double-click on the green box. The green box
changes to red. When the box is red, autoscrolling is turned off and the detail
panel remains in the location shown in the overview panel red box.
d
To resize the objects in the detail panel, click on the Zoom in Tool and Zoom
out Tool buttons; click on the Reset Zoom tool button to return to the default
graph view.
e
To display the data points for each plot in the detail panel, select the Markers
check box.
f
To display a legend in the detail panel, select the Legend check box.
g
To display the X-axis grid lines, select the Grid X check box. This check box
is selected by default.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
73 — Graphing statistics
h
To display the Y1 grid lines, select the Grid Y1 check box. The Y1 axis is
displayed on the left side of the detail panel. The grid lines are displayed only
if the Y1 axis is in use.
i
To display the Y2 grid lines, select the Grid Y2 check box. The Y2 axis is
displayed on the right side of the detail panel. The grid lines are displayed
only if the Y2 axis is in use.
j
Perform the following steps to hide or show a plot in the detail panel. This is
required when plots in the detail panel overlap.
i
Choose the plot to hide in the detail panel.
ii
Click in the column heading configuration panel and choose Plot n in the
drop-down list, where n is the plot to hide. The check mark is removed
from the plot list, and the plot is removed from the detail and data
panels.
Note — Statistics collection does not stop when a plot is hidden.
iii
8
To show the plot in the detail panel, right-click in the column heading
of the data panel and choose Plot n from the contextual menu, where n
is the plot to show. A check mark is displayed beside the plot in the
contextual menu and the plot is displayed in the detail and data panels.
To clear a plot from the detail panel but keep the plot in the configuration panel
so that the plot can be used to create a new plot:
i
Choose the object in the list and click on the Clear button. The plot is deleted
from the detail and data panels.
ii
Click on the plot in the Statistics Counter column and choose a unique
statistics counter from the drop-down list.
iii
Click on the Y Axis column and choose an axis from the drop-down list.
9
To remove a plot from the detail and data panels, select the object in the list and
click on the Remove button. The plot is deleted from the detail and data panels.
10
Perform one of the following steps, if required.
a
To switch from a real-time statistics graph to a historical statistics graph,
click on the Stop button and click on the Historical Plot button. The detail
panel clears and the statistics stored in the database are plotted in the detail
panel.
b
To switch from a historical statistics graph to a real-time statistics graph,
choose a polling interval from the real-time polling interval drop-down menu
or enter a value between 10 and 3600 seconds and click on the Real-time Plot
button. The detail panel clears and real-time statistics plotting begins.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
73-9
73 — Graphing statistics
11
Save the statistics graph results, if required.
Note 1 — Only the detail that appears in the detail panel is saved. To
change the view in the detail panel before you save the results, use the
overview panel or the zoom buttons.
Note 2 — If the Legend check box is selected, the legend is saved with
the statistics graph results.
12
13
i
Click on the Save Current View button. The Save as form appears.
ii
Specify a directory in which to save the statistics graph using the Save In
parameter. The Save In form opens.
iii
Enter a filename in the File Name field.
iv
Choose JPG or PNG from the Type of File drop-down menu.
v
Click on the Save button. The Save as form closes and the graph is saved in
the specified JPG or PNG file.
Save the statistics table results, if required. All of the statistics in the data panel
are saved.
i
Right-click on the plot value list heading and choose Save To File from the
contextual menu. The Save form opens.
ii
Specify a directory in which to save the statistics table using the Save In
parameter. The Save In form opens.
iii
Enter a filename using the File Name field.
iv
Choose HTML or CSV from the Type of File drop-down menu.
v
Click on the Save button. The Save form closes and the contents of the plot
value list are saved in the specified file.
Close the Statistics Plotter form.
Note — The Statistics Plotter form cannot be saved. When you close a
Statistics Plotter form, the data in the form is deleted.
73-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
73 — Graphing statistics
Procedure 73-3 To modify a statistics graph
Perform this procedure to modify an existing statistics graph that contains one or more
plots.
1
Perform one of the following.
a
To open a Statistics Plotter form, choose Tools→Statistics Plotter→Statistics
Plotter (#) from the 5620 SAM main menu. The Statistics Plotter form opens.
b
To add an object to the Statistics Plotter form:
i
Choose the object on which to modify a statistics graph.
ii
Open a view of the object in the navigation tree.
iii
Right-click on the object in the navigation tree view selector and choose
Properties from the contextual menu. The properties form for the
object opens with the General tab displayed.
iv
Click on the Statistics tab button.
v
Choose statistics class from the object drop-down list.
vi
Click on the Plotter button and choose Statistics Plotter (#) from the
drop-down menu. The Statistics Plotter form opens with the current
plot information displayed.
Note — A statistics graph can plot up to four statistics counters. The
statistics counters can be same the if there are four different objects.
If only one object is used, each statistics counter must be unique.
If the Statistics Plotter already contains four plots, a dialog box notifies
you that the graph contains the maximum allowed number of plots,
which means that the Statistics Plotter cannot be modified. Click on the
OK button.
If the Statistics Plotter (#) menu item is not available, the Statistics
Plotter does not support the selected object type.
2
Perform steps 2 to 13 of Procedure 73-2.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
73-11
73 — Graphing statistics
73-12
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
74 — Using the 5620 SAM-O to collect
statistics
74.1 Using the 5620 SAM-O to collect statistics
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
74-2
74-1
74 — Using the 5620 SAM-O to collect statistics
74.1
Using the 5620 SAM-O to collect statistics
This chapter is an overview of statistics collection using the 5620 SAM-O interface.
See the 5620 SAM-O OSS Interface Developer Guide for more information.
Third-party statistics collection process
A third-party OSS client application can use the following methods to collect
5620 SAM accounting and performance statistics from the 5620 SAM-O interface:
• findToFile—for infrequent, low-volume transfers of statistics data from the
5620 SAM database. The findToFile method can save statistics for multiple NEs
in one file. The 5620 SAM generates a FileAvailableEvent each time that a file is
created using this method.
• registerLogToFile—for creating accounting statistics export files that are based
on specific class types. The 5620 SAM exports the accounting statistics data to a
file after it retrieves the data from an NE, and saves the file in a specified directory
on the main server. The 5620 SAM generates a LogFileAvailableEvent each time
that a file is created using this method, which is asynchronous.
Note — Alcatel-Lucent recommends that you use the
registerLogToFile method to maintain an up-to-date view of
accounting statistics. Use the findToFile method for infrequent
queries on performance or accounting statistics. Do not use the
findToFile method in large networks with high statistics collection
rates. See the 5620 SAM-O OSS Interface Developer Guide for more
information.
See the 5620 SAM-O OSS Interface Developer Guide for more information about
using the 5620 SAM-O to transfer statistics records from the 5620 SAM database to
your OSS client application.
XML methods for transferring statistics files to OSS client applications
Table 74-1 describes the XML methods and the associated parameters that a
5620 SAM-O client can use to retrieve statistics from a 5620 SAM main server.
Table 74-1 XML methods for collecting statistics
Method
Description
Input parameters and descriptions
find
Returns the set of objects of
the specified type that
match the filter criteria.
fullClassName
Package qualified class
name in dot-separated
format
filter (optional)
Filter for properties of the
class that correspond to
fullClassName
resultFilter (optional)
Filter that limits the
information returned per
object
(1 of 2)
74-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
74 — Using the 5620 SAM-O to collect statistics
Method
Description
Input parameters and descriptions
findToFile
Finds the set of objects of
the specified type that
match the given filter
criteria, and places the
results in the specified file
on the server. The 5620 SAM
generates a
FileAvailableEvent when
the method execution is
complete.
fullClassName
Package qualified class
name in dot-separated
format
fileName
File in which to store the
results of this find
operation, specified using a
relative file path
filter (optional)
Filter for properties of the
class that correspond to
fullClassName
resultFilter (optional)
Filter that limits the
information returned per
object
fullClassName
A comma-separated list of
accounting statistics classes
dirName
The relative path to the
directory in which to save
the files. The path is
relative to the
accountingStats directory
under the OSS XML export
directory. Alcatel-Lucent
recommends using separate
directories for different
applications that export
statistics.
compress (optional)
Specifies whether export
files are created in a
compressed format
jmsClientId
The JMS client ID that is to
be notified when a new
export file is created. A
notification message is sent
to each client that registers
for statistics each time the
method creates an export
file that is associated with
the client.
resultFilter (optional)
Specifies the attributes that
are to be included in the
exported data records. You
can use the resultFilter
parameter to reduce the
export file size.
registerLogToFile
Creates export files of
accounting statistics on the
5620 SAM server for
statistics collected after
registration. The 5620 SAM
generates a
LogFileAvailableEvent when
a file is ready for retrieval.
(2 of 2)
Third-party applications for processing statistics
You can use an in-house statistics-processing application or a third-party vendor
application, such as Quallaby or Infovista, to manage the statistics information that
the 5620 SAM collects.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
74-3
74 — Using the 5620 SAM-O to collect statistics
74-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Statistics content
75 — Statistics record format
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
75.1 Statistics types
75-2
75.2 Performance statistics
75.3 Accounting statistics
75-3
75-4
75.4 Server performance statistics
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
75-13
December 2009
75-1
75 — Statistics record format
75.1
Statistics types
Table 75-1 lists and describes the statistics types that the 5620 SAM supports.
Table 75-1 5620 SAM statistics types
Statistics type
Description
Performance
Performance statistics provide categorized information about network
throughput. Performance statistics are available from most physical
equipment and logical element GUI configuration forms.
Accounting
There are three main classes of accounting policy: service, network, and
subscriber.
An accounting statistics record contains the following common fields in
addition to the counters that are associated with each policy type:
•
•
•
•
•
•
•
•
Time Captured
Record Type
Monitored Object
Monitored Object Name
Site Name
Site ID
Periodic Time
Time Recorded
A service accounting statistics record contains the following additional
fields:
•
•
•
•
Sap Id
Svc Id
Sdp Id
Queue Id
A network accounting statistics record contains the following additional
fields:
•
•
•
•
Forwarding Class
Lag Port
Port Id
Queue Id
A subscriber accounting statistic record contains the following additional
fields:
•
•
•
Subscriber Id
Subscriber Profile Id
Sla Profile Id
The 5620 SAM creates separate ingress and egress statistics records for the
accounting statistics that are associated with an NE.
Server performance
75-2
Server performance statistics include 5620 SAM main and auxiliary server
performance counters that monitor memory usage, JMS activity, alarm
activity, SNMP trap receipt, NE resynchronizations, and statistics collection.
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
75.2
Performance statistics
Performance statistics provide categorized information about network throughput.
Performance statistics records are viewable from most physical-equipment and
logical-element GUI properties forms. The information in a performance statistics
record includes the following:
•
•
•
•
collection timestamp
collection record type
source device and object identifiers
Suspect indicator that indicates a problem with the collected statistics; for
example, when an NE is unresponsive to SNMP requests
• statistics counters that contain the raw data
Table 75-2 lists and describes the properties in a performance statistics record.
Table 75-2 Performance statistics record properties
Property
Description
Monitored Object
Unique identifier of the object from which the statistics are collected
Monitored Object Name
Name of the object from which the statistics are collected
Periodic Time
Time between collections
Record Type
The type of record, based on the following collection types:
•
•
•
Scheduled Full
Performed according to a user-configurable schedule
On-demand
Performed immediately at the request of a 5620 SAM operator
Real-time
Performed as part of real-time graph creation using the 5620 SAM
Statistics Plotter
Site ID
NE identifier
Site Name
NE name
Suspect
Indicates a statistics collection failure.
Time Captured
Time at which the statistics are collected
Note — When the Suspect indicator in a record is set, the counters in
the record contain the following values:
• periodic counters—zero
• non-periodic counters—the value of the same counter in the most
recent non-suspect record
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-3
75 — Statistics record format
75.3
Accounting statistics
Accounting statistics are available for network ports, SAPs, SDPs, and subscribers.
Service accounting statistics provide service-usage data for billing requirements.
Network accounting statistics provide service-quality data for SLA QoS compliance
requirements. Subscriber accounting statistics provide subscriber profile usage
information for billing and SLA compliance. The information in an accounting
statistics record includes the following:
•
•
•
•
collection timestamp
collection record type
source device and object identifiers
statistics counters that contain the raw data
Table 75-3 describes the accounting policy types that the 5620 SAM supports.
Table 75-3 Accounting policy types
Accounting
policy type
Policy name and description
NE acronym
Application
assurance
AA Application—octet, packet, and flow counters for applications
aaApp
AA Application Group—octet, packet, and flow counters for application groups
aaAppGrp
AA Protocol—octet, packet, and flow counters for protocols
aaProt
AA Subscriber Application—octet, packet, and flow counters for applications per
subscriber
aaSubAppGrp
AA Subscriber Protocol—octet, packet, and flow counters for protocols per
subscriber
aaSubProt
Custom Record AA Subscriber—octet, packet, and flow counters per subscriber
aaSubCustom
Combined MPLS LSP Egress—counters for egress data path at ingress LER
cmmplslspe
Combined MPLS LSP Ingress—counters for ingress data path at egress LER
cmmplslspi
Combined Network Ing Egr Octets—octet counters for ingress and egress network
port queues
cmNio, cmNeo
Combined Queue Groups—packet and octet counters for ingress and egress service
queue groups and egress network queue groups
cmQgse, cmQgsi,
cmQgne
Network Egress Octet—octet counters for egress network port queues
neo
Network Ingress Octet—octet counters for ingress network port queues
nio
Network Egress Packet—packet counters for egress network port queues
nep
Network Ingress Packet—packet counters for ingress network port queues
nip
Queue Group Octets—octet counters for ingress and egress service queue groups
and egress network queue groups
qgose, qgosi, qgone
Queue Group Packets—packet counters for ingress and egress service queue groups
and egress network queue groups
qgpse, qgpsi, qgpne
Network
(1 of 2)
75-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Accounting
policy type
Policy name and description
NE acronym
Service
Combined Service Ing Egr Octets—octet counters for ingress and egress SAP queues
cmSio, cmSeo
Combined Service Ingress—packet and octet counters for ingress SAP queues
cmSipo
Combined Service SDP Ingress Egress—per-service packet and octet counters on
ingress and egress SDPs
cpSdpipo, cpSdpepo
Compact Service Ingress Octets—octet counters for ingress SAP queues
ctSio
Complete Service Ingress Egress—packet and octet counters for ingress SAP queues
cpSipo, cpSepo
Complete Service SDP Ingress Egress—packet and octet counters on ingress and
egress SDPs
cmSdpipo, cmSdpepo
Custom Record Service—user-specified Complete Service Ingress Egress counters
cpSipo, cpSepo
Service Egress Octet—octet counters for egress SAP queues
seo
Service Ingress Octet—octet counters for ingress SAP queues
sio
Service Egress Packet—packet counters for egress SAP queues
sep
Service Ingress Packet—packet counters for ingress SAP queues
sip
Complete Subscriber Ingress Egress—per-subscriber packet and octet counters for
ingress and egress SAP queues
cpSBipo, cpSBepo
Custom Record Subscriber—user-specified Complete Subscriber Ingress Egress
counters
cpSBipo, cpSBepo,
cpSBipooc,
cpSBepooc
Subscriber
(2 of 2)
Table 75-4 lists and describes the properties in an accounting statistics record.
Table 75-4 Accounting statistics record properties
Property
Description
Forwarding Class
Forwarding class associated with a queue
Lag Port
Identifies a LAG port
Monitored Object
Detailed information about the object for which the statistics
are collected
Monitored Object Name
Name of the object for which the statistics are collected
Periodic Time
Not applicable to accounting statistics
Port Id
Identifies a port
Queue Id
Identifies a hardware queue
Record Type
Type of collection, for example, Scheduled Full
Sap Id
Physical port identifier portion of a SAP definition
Sdp Id
Identifies an SDP
Site ID
Identifies a site
Site Name
Identifies the name of a site
SlaProfile Id
Identifies the value assigned to an SLA profile
Subscriber Id
Identifies a subscriber
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-5
75 — Statistics record format
Property
Description
Subscriber Profile Id
Identifies a subscriber profile
Svc Id
Identifies a service
Time Captured
Time when the 5620 SAM starts to process the data file
collected from the NE
Time Recorded
Time when the statistics were collected on the NE
(2 of 2)
Table 75-5 lists the statistics counters in each accounting policy.
Table 75-5 Accounting statistics counters by policy
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
AA Protocol
AA Protocol Stats
Net to Sub Active Flows
naf
AA Application
AA App Stats
AA Application Group
AA App Grp Stats
Net to Sub Admit Flows
nfa
AA Subscriber Protocol
AA Sub Prot Stats
Net to Sub Admit Octets
nba
AA Subscriber Application
AA Sub App Stats
Net to Sub Admit Pkts
npa
Net to Sub Deny Flows
nfd
Net to Sub Deny Octets
nbd
Net to Sub Deny Pkts
npd
Num of Subs
nsub
Sub to Net Active Flows
saf
Sub to Net Admit Flows
sfa
Sub to Net Admit Octets
sba
Sub to Net Admit Pkts
spa
Sub to Net Deny Flows
sfd
Sub to Net Deny Octets
sbd
Sub to Net Deny Pkts
spd
Total Flow Duration
tfd
Total Term Flows
tfc
(1 of 7)
75-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
Combined MPLS LSP Egress
Ingress
CombinedMplsLspEgress
Forwarding Class
fc
In Profile Octets Forwarded
iof
Out of Profile Octets Forwarded
oof
In Profile Packets Forwarded
ipf
Out of Profile Packets
Forwarded
opf
Forwarding Class
fc
In Profile Octets Forwarded
iof
Out of Profile Octets Forwarded
oof
In Profile Packets Forwarded
ipf
Out of Profile Packets
Forwarded
opf
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
High Octets Dropped
hod
High Octets Offered
hoo
In Profile Octets Forwarded
iof
Low Octets Dropped
lod
Low Octets Offered
loo
Out Of Profile Octets Forwarded
oof
Uncoloured Octets Offered
uco
Uncoloured Packets Offered
ucp
CombinedMplsLspIngress
Combined Network Ing Egr
Octets
CombinedNetworkEgressOctets
CombinedNetworkIngressOctets
Combined Service Ing Egr
Octets
CombinedServiceEgressOctets
CombinedServiceIngressOctets
(2 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-7
75 — Statistics record format
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
Combined Service Ingress
CombinedServiceIngressPacketOctets
High Octets Dropped
hod
High Octets Offered
hoo
High Pkts Dropped
hpd
High Pkts Offered
hpo
In Profile Octets Forwarded
iof
In Profile Pkts Forwarded
ipf
Low Octets Dropped
lod
Low Octets Offered
loo
Low Pkts Dropped
lpd
Low Pkts Offered
lpo
Out Of Profile Octets Forwarded
oof
Out Of Profile Pkts Forwarded
opf
Uncoloured Octets Offered
uco
Uncoloured Packets Offered
ucp
Total Octets Dropped
tod
Total Octets Forwarded
tof
Total Packets Dropped
tpd
Total Packets Forwarded
tpf
Total Octets Forwarded
tof
Total Packets Forwarded
tpf
High Octets Dropped
hod
High Octets Offered
hoo
Low Octets Dropped
lod
Low Octets Offered
loo
Uncoloured Octets Offered
uco
Uncoloured Packets Offered
ucp
Combined Service SDP
Ingress Egress
CombinedSdpIngressPacketOctets
CombinedSdpEgressPacketOctets
Compact Service Ingress
Octets
CompactServiceIngressOctets
(3 of 7)
75-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
Complete Service Ingress
Egress
CompleteServiceEgressPacketOctets
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
In Profile Pkts Dropped
ipd
In Profile Pkts Forwarded
ipf
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
Out Of Profile Pkts Dropped
opd
Out Of Profile Pkts Forwarded
opf
High Octets Dropped
hod
High Octets Offered
hoo
High Pkts Dropped
hpd
High Pkts Offered
hpo
In Profile Octets Forwarded
iof
In Profile Pkts Forwarded
ipf
Low Octets Dropped
lod
Low Octets Offered
loo
Low Pkts Dropped
lpd
Low Pkts Offered
lpo
Out Of Profile Octets Forwarded
oof
Out Of Profile Pkts Forwarded
opf
Uncoloured Octets Offered
uco
Uncoloured Packets Offered
ucp
Total Octets Dropped
tod
Total Octets Forwarded
tof
Total Packets Dropped
tpd
Total Packets Forwarded
tpf
Total Octets Forwarded
tof
Total Packets Forwarded
tpf
Total Octets Dropped
tod
Total Octets Forwarded
tof
Total Packets Dropped
tpd
Total Packets Forwarded
tpf
Total Octets Forwarded
tof
Total Packets Forwarded
tpf
CompleteServiceIngressPacketOctets
Complete Service SDP
Ingress Egress
CombinedSdpIngressPacketOctets
CombinedSdpEgressPacketOctets
CompleteSdpIngressPacketOctets
CompleteSdpEgressPacketOctets
(4 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-9
75 — Statistics record format
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
Complete Subscriber
Ingress Egress
CompleteSubscriberIngressPacketOctets
High Priority Pkts Dropped
hpd
High Priority Pkts Offered
hpo
Low Priority Pkts Dropped
lpd
Low Priority Pkts Offered
lpo
CompleteSubscriberEgressPacketOctets
Custom Record AA
Subscriber
Custom Record Service
Custom Record Subscriber
AASubCustomStats
AASapCustomStats
CustomRecordService
CustomRecordSubscriber
High Priority Octets Dropped
hod
High Priority Octets Offered
hoo
Low Priority Octets Dropped
lod
Low Priority Octets Offered
loo
In Profile Octets Forwarded
iof
Out Of Profile Octets Forwarded
oof
In Profile Pkts Forwarded
ipf
Out Of Profile Pkts Forwarded
opf
Uncoloured Octets Offered
uco
Uncoloured Pkts Forwarded
ucp
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
In Profile Pkts Dropped
ipd
In Profile Pkts Forwarded
ipf
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
Out Of Profile Pkts Dropped
opd
Out Of Profile Pkts Forwarded
opf
Short Duration Flows
—
Medium Duration Flows
—
Long Duration Flows
—
Total Flow Duration
—
Total Flows Completed
—
User-selectable Complete
Service Ingress Egress counters
Various
All Octets Offered
—
All Packets Offered
—
User-selectable Complete
Service Ingress Egress counters
Various
All Octets Offered
—
All Packets Offered
—
(5 of 7)
75-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
Network Egress Octet
NetworkEgressOctets
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
In Profile Pkts Dropped
ipd
In Profile Pkts Forwarded
ipf
Out Of Profile Pkts Dropped
opd
Out Of Profile Pkts Forwarded
opf
In Profile Pkts Dropped
ipd
In Profile Pkts Forwarded
ipf
Out Of Profile Pkts Dropped
opd
Out Of Profile Pkts Forwarded
opf
In Profile Octets Dropped
iod
In Profile Octets Forwarded
iof
Out Of Profile Octets Dropped
ood
Out Of Profile Octets Forwarded
oof
High Octets Dropped
hod
High Octets Offered
hoo
In Profile Octets Forwarded
iof
Low Octets Dropped
lod
Low Octets Offered
loo
Out Of Profile Octets Forwarded
oof
Uncoloured Octets Offered
uco
Uncoloured Packets Offered
ucp
In Profile Pkts Dropped
ipd
In Profile Pkts Forwarded
ipf
Out Of Profile Pkts Dropped
opd
Out Of Profile Pkts Forwarded
opf
Network Ingress Octet
Network Egress Packet
Network Ingress Packet
Service Egress Octet
Service Ingress Octet
Service Egress Packet
NetworkIngressOctets
NetworkEgressPackets
NetworkIngressPackets
ServiceEgressOctets
ServiceIngressOctets
ServiceEgressPackets
(6 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-11
75 — Statistics record format
Accounting policy
5620 SAM statistics object
5620 SAM counter
NE counter
Service Ingress Packet
ServiceIngressPackets
High Pkts Dropped
hpd
High Pkts Offered
hpo
In Profile Pkts Forwarded
ipf
Low Pkts Dropped
lpd
Low Pkts Offered
lpo
Out Of Profile Pkts Forwarded
opf
Uncoloured Pkts Offered
ucp
(7 of 7)
Table 75-6 lists and defines each accounting statistics counter.
Table 75-6 Accounting statistics counter definitions
Counter name
Definition
All Octets Offered
Offered packets enter a queue and are dropped or forwarded.
All Packets Offered
An octet value is a packet value expressed in Bytes.
Forwarding Class
The forwarding class of the traffic; this is a classification rather than a counter
High Octets Dropped
High-priority packets for a traffic class are marked as in-profile on the ingress
classification or based on the interpretation of the QoS marking.
High Octets Offered
High Pkts Dropped
High Pkts Offered
High Priority Octets Dropped
Offered packets enter a queue and are dropped or forwarded.
Dropped packets are not forwarded through a queue.
An octet value is a packet value expressed in Bytes.
High Priority Octets Offered
High Priority Pkts Dropped
High Priority Pkts Offered
In Profile Octets Dropped
In-profile packets are received at a rate that is lower than the queue CIR.
In Profile Octets Forwarded
Forwarded packets are sent to an egress queue.
In Profile Packets Forwarded
Dropped packets are not forwarded through a queue.
In Profile Pkts Dropped
An octet value is a packet value expressed in Bytes.
In Profile Pkts Forwarded
Long Duration Flows
Subscriber host application sessions that are longer than 180s in duration
Low Octets Dropped
Low-priority packets for a traffic class are marked as out-of-profile on the ingress
classification or based on the interpretation of the QoS marking.
Low Octets Offered
Low Pkts Dropped
Low Pkts Offered
Low Priority Octets Dropped
Offered packets enter a queue and are dropped or forwarded.
Dropped packets are not forwarded through a queue.
An octet value is a packet value expressed in Bytes.
Low Priority Octets Offered
Low Priority Pkts Dropped
Low Priority Pkts Offered
Medium Duration Flows
Subscriber host application sessions that are 180s or less in duration
(1 of 2)
75-12
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Counter name
Definition
Net to Sub Active Flows
Net to Sub traffic flows from the network to a subscriber.
Net to Sub Admit Flows
An active flow is a flow that is opened, closed, opened and closed, or continued
during a collection interval.
Net to Sub Admit Octets
Net to Sub Admit Pkts
Net to Sub Deny Flows
Net to Sub Deny Octets
Admit objects are objects that are forwarded.
Deny objects are objects that are not forwarded.
An octet value is a flow or packet value expressed in Bytes.
Net to Sub Deny Pkts
Num of Subs
The number of subscribers that have the specified flow type during the collection
interval
Out Of Profile Octets Dropped
Out-of -profile packets are received at a rate that is higher than the queue CIR.
Out Of Profile Octets Forwarded
Forwarded packets are sent to an egress queue.
Out of Profile Packets Forwarded
Dropped packets are not forwarded through a queue.
Out Of Profile Pkts Dropped
An octet value is a packet value expressed in Bytes.
Out Of Profile Pkts Forwarded
Short Duration Flows
Subscriber host application sessions that are 30s or less in duration
Sub to Net Active Flows
Sub to Net traffic flows from a subscriber to the network.
Sub to Net Admit Flows
An active flow is a flow that is opened, closed, opened and closed, or continued
during a collection interval.
Sub to Net Admit Octets
Sub to Net Admit Pkts
Sub to Net Deny Flows
Sub to Net Deny Octets
Admit objects are objects that are forwarded.
Deny objects are objects that are not forwarded.
An octet value is a flow or packet value expressed in Bytes.
Sub to Net Deny Pkts
Total Flow Duration
Aggregate duration, in seconds, of the completed flows at the time of collection.
Total Flows Completed
The number of flows in each direction that completed during the collection interval.
Total Octets Dropped
Offered packets enter a queue and are dropped or forwarded.
Total Octets Forwarded
Forwarded packets are sent to an egress queue.
Total Packets Dropped
Dropped packets are not forwarded through a queue.
Total Packets Forwarded
An octet value is a packet value expressed in Bytes.
Total Term Flows
The number of flows in each direction that completed during the collection interval.
Uncoloured Octets Offered
Octets and packets can be modified or colored using color profiles. Color profiling
adds the ability to selectively treat packets received on a SAP as in-profile or
out-of-profile regardless of the queue forwarding rate. This allows a customer or
access device to color a packet out-of-profile with the intention of keeping the
in-profile bandwidth for higher-priority packets.
Uncoloured Packets Offered
Uncoloured Pkts Forwarded
Uncoloured Pkts Offered
Offered packets enter a queue and are dropped or forwarded.
Forwarded packets are sent to an egress queue.
An octet value is a packet value expressed in Bytes.
(2 of 2)
75.4
Server performance statistics
Server performance statistics provide memory usage, alarm counters, and network
activity statistics, and are collected on each server in a 5620 SAM server cluster. The
information in a performance statistic record includes the following:
• collection timestamp
• collection record type
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-13
75 — Statistics record format
• source object identifiers
• statistics counters that contain the raw data
Table 75-2 lists and describes the properties in a server performance statistics record.
Table 75-7 Server performance statistics properties
Properties
Description
Monitored Object
Detailed information about the object for which the statistics are
collected
Monitored Object Name
Name of the object for which the statistics are collected
Periodic Time
Time difference between one data record collection period and the
next
Record Type
Type of collection, for example, Scheduled Full or On-demand
Time Captured
Time when the statistics were collected
Table 75-8 lists each server performance statistics policy type and the types of
5620 SAM servers that the policy monitors.
Table 75-8 Monitored 5620 SAM servers
Server performance statistics policy
Monitored servers
Alarm Rate
Main server
Auxiliary server
JMS Durable XML Subscriber Session
JMS server
JMS Subscriber Topic
JMS server
Node Resync
Main server
Publisher Map Event
Main server
Publisher Object Event
Main server
Publisher Queue
Main server
Publisher Realtime Event
Main server
Publisher SAMC Event
Main server
Publisher XML Event
Main server
Server Memory
Main server
Auxiliary server
JMS server
SNMP Trap
Statistics Collection
Main server
Main server
Auxiliary server
Table 75-5 describes the server performance statistics counters.
75-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Table 75-9 Server performance statistics counters
Server
performance
statistics class
Counter name
Counter description
Alarm Rate
Alarm Total
Total number of alarms
Cleared
Count of cleared alarms
Condition
Count of condition alarms
Critical
Count of critical alarms
Indeterminate
Count of indeterminate alarms
Info
Count of information alarms
Major
Count of major alarms
Minor
Count of minor alarms
Warning
Count of warning alarms
JMS Durable XML
Subscriber Session
Total Message Count
Total message count for a given durable XML
subscriber session
JMS Subscriber
Topic
Max Topic Message Count
The maximum message count in a subscription
queue for a given topic
Min Topic Message Count
The minimum message count in a subscription
queue for a given topic
Subscription Count
The total subscription count for a given topic
Total Topic Message Count
Total messages in all subscription queues for a
given topic
Scheduled Resync Failure
Count of failed scheduled resynchronizations
Scheduled Resync Processed
Count of processed scheduled
resynchronizations
Scheduled Resync Received
Count of scheduled resynchronizations received
Unscheduled Resync Failure
Count of unscheduled resynchronizations
Unscheduled Resync Processed
Count of processed unscheduled
resynchronizations
Unscheduled Resync Received
Count of unscheduled resynchronizations
received
Edge List Event Count
Count of EdgeListEvent events
Edge Status Event Count
Count of EdgeStatusEvent events
Incremental Event Count
Count of IncrementalEvent events
Incremental Highlight Event Count
Count of IncrementalHighlightEvent events
Map Service Event Count
Count of MapServiceEvent events
Vertex Status Event Count
Count of VertexStatusEvent events
Vertex Topology Event Count
Count of VertexTopologyEvent events
Vertex Tree Event Count
Count of VertexTreeEvent events
View Event Count
Count of ViewEvent events
Node Resync
Publisher Map
Event
(1 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-15
75 — Statistics record format
Server
performance
statistics class
Counter name
Counter description
Publisher Object
Event
Attribute Value Change Context Event Count
Count of AttributeValueChangeContext events
Delete Event Vessel Count
Count of DeleteEventVessel events
Event Vessel Count
Total EventVessel count events
File Available Event Count
Count of FileAvailableEvent events
Non Persistent Attribute Value Change Event
Count
Count of
NonPersistentAttributeValueChangeEvent
events
Non Persistent Object Creation Event Count
Count of NonPersistentObjectCreationEvent
events
Non Persistent Object Deletion Event Count
Count NonPersistentObjectDeletionEvent
events
Object Thin Creation Event Count
Count of ObjectThinCreationEvent events
Olc Update Completed Event Count
Count of OLCUpdateCompletedEvent events
Text Message Event Count
Count of TextMessageEvent events
Truncate MOTable Event Count
Count of TruncateMOTableEvent events
Object Event In Publisher Queue
Number of outstanding events in the object
publisher queue
Reatime Event In Publisher Queue
number of outstanding events in the real-time
publisher queue
Xml Event In Publisher Queue
Number of outstanding events in the XML
publisher queue
Realtime Data Communication Failure Count
Count of RealtimeDataCommunicationFailure
events
Realtime Data Event Count
Count of RealtimeDataEvent events
Realtime Data Failure Count
Count of RealtimeDataFailure events
Realtime Data Missed Event Count
Count of RealtimeDataMissedEvent events
Anw Topology As Event Vessel Count
Count of AnwTopologyAsEventVessel events
Anw Topology Event Count
Count of AnwTopologyEvent events
Bgp Rib Info Event Count
Count of BgpRibInfoEvent events
Bgp Route Targets Event Count
Count of BgpRouteTargetsEvent events
Cpaa State Change Event Count
Count of CpaaStateChangeEvent events
Cpam Sim Event Count
Count of CpamSimEvent events
Cpam State Change Event Count
Count of CpamStateChangeEvent events
Internal Managed Route Event Count
Count of InternalManagedRouteEvent events
Operation State Change Event Count
Count of OperationStateChangeEvent events
Topology Area Event Vessel Count
Count of TopologyAreaEventVessel events
Topology Error Event Count
Count of TopologyErrorEventCount events
Topology Event Count
Count of TopologyEvent events
Publisher Queue
Publisher Realtime
Event
Publisher SAMC
Event
(2 of 4)
75-16
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
75 — Statistics record format
Server
performance
statistics class
Counter name
Counter description
Publisher XML Event
Alarm Propagation List Event Count
Count of AlarmPropagationListEvent events
Alarm Status Change Event Count
Count of AlarmStatusChangeEvent events
Attribute Value Change Event Count
Count of AttributeValueChangeEvent events
Db Activity Event Count
Count of DBActivityEvent events
Db Connection State Change Event Count
Count of DBConnectionStateChangeEvent events
Db Error Event Count
Count of DBErrorEvent events
Db Proxy State Change Event Count
Count of DBProxyStateChangeEvent events
Deployer Event Count
Count of DeployerEvent events
Exception Event Count
Count of ExceptionEvent events
Incremental Request Event Count
Count of IncrementalRequestEvent events
Keep Alive Event Count
Count of KeepAliveEvent events
Log File Available Event Count
Count of LogFileAvailableEvent events
Managed Route Event Count
Count of ManagedRouteEvent events
Object Creation Event Count
Count of ObjectCreationEvent events
Object Deletion Event Count
Count of ObjectDeletionEvent events
Relationship Change Event Count
Count of RelationshipChangeEvent events
Script Execution Event Count
Count of ScriptExecutionEvent events
State Change Event Count
Count of stateChangeEvent events
Stats Event Count
Count of StatsEvent events
Terminate Client Session Count
Count of terminateClientSession events
Committed Heap Memory
Total amount of memory allocated for use by
code
Committed Non Heap Memory
Initial amount of memory allocated to the heap
Init Heat Memory
Initial amount of memory allocated to the heap
Init Non Heap Memory
Initial amount of memory allocated for use by
code
Max Heap Memory
Maximum number of kbytes occupied by the
heap
Max Non Heap Memory
Maximum number of kbytes occupied by the
code
Used Heap Memory
Number of kbytes currently occupied by the
heap
Used Non Heap Memory
Number of kbytes currently occupied by code
Server Memory
(3 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
75-17
75 — Statistics record format
Server
performance
statistics class
Counter name
Counter description
SNMP Trap
Dropped Backpressure
Count of traps dropped due to back pressure
from the server
Dropped Duplicate
Count of duplicate traps dropped
Dropped Full Resync
Count of traps dropped during a full
resynchronization
Dropped Not Managed
Count of traps dropped from unmanaged NEs
Dropped Out of Sequence
Count of out of sequence traps dropped
Dropped Trap Disabled
Count of disabled traps dropped
Incoming
Count of incoming traps
Accounting Stats Failure
Number of failed accounting statistics
collections
Accounting Stats Pending
Number of pending accounting statistics
collection requests
Accounting Stats Processed
Number of processed accounting statistics
collection requests
Accounting Stats Total
Total number of accounting statistics collection
requests
File Accounting Stats Pending
Number of pending accounting statistics
collection requests
File Accounting Stats Processed
Number of processed accounting statistics
collection requests
File Accounting Stats Total
Total number of accounting statistics collection
requests
Scheduled Polling Stats Pending
Number of pending scheduled MIB statistics
collection requests
Scheduled Polling Stats Processed
Number of scheduled MIB statistics processed
Scheduled Polling Stats Records
Number of scheduled MIB statistics records
updated
Scheduled Polling Stats Total
Total number of scheduled MIB statistics
collection requests
Scheduled Stats Failure
Number of failed unscheduled MIB statistics
collection requests
Unscheduled Polling Stats Pending
Number of pending scheduled MIB statistics
collection requests
Unscheduled Polling Stats Processed
Number of unscheduled MIB statistics processed
Unscheduled Polling Stats Records
Number of unscheduled MIB statistics records
updated
Unscheduled Polling Stats Total
Total number of unscheduled MIB statistics
collection requests
Unscheduled Stats Failure
Number of failed unscheduled MIB statistics
collection requests
Statistics Collection
(4 of 4)
75-18
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
Appendices
A. 7210 SAS-E Release 1.0 statistics counters
A-1
B. 7210 SAS-M Release 1.0 statistics counters
B-1
C. 7250 SAS Release 2.0 statistics counters
C-1
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics
counters
D-1
E. 7450 ESS Release 7.0 statistics counters
E-1
F. 7701 CPAA Release 3.0 statistics counters
G. 7705 SAR Release 2.0 statistics counters
F-1
G-1
H. 7710 SR Release 7.0 statistics counters
H-1
I. 7750 SR Release 7.0 statistics counters
I-1
J. 9500 MPR statistics counters
K. Generic NE statistics counters
J-1
K-1
L. OmniSwitch Release 6.3.4 statistics counters
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
L-1
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A.
7210 SAS-E Release 1.0 statistics
counters
A.1 7210 SAS-E Release 1.0 statistics counters
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-2
A-1
A. 7210 SAS-E Release 1.0 statistics counters
A.1
7210 SAS-E Release 1.0 statistics counters
This appendix lists in tabular form the statistics counters that the 5620 SAM supports
for the 7210 SAS-E, Release 1.0. Each 5620 SAM counter entry in a table contains
the name and description of the corresponding device MIB counter.
The 5620 SAM counter name in a table entry is the internal counter identifier that is
required for statistics retrieval through the 5620 SAM OSSI. The displayed counter
name in the 5620 SAM GUI is typically an expansion of this identifier. For example,
the receivedBroadcastPackets counter name in the equipment table corresponds to
the Received Broadcast Packets counter name on the Log Record form for an
Ethernet port.
Note 1 — The tables list the 5620 SAM-supported statistics counters
for the current release of the device. Counters that are supported for a
previous device release, but not for the current release, are not listed.
Note 2 — A statistics counter in the 5620 SAM GUI whose displayed
name ends with “Periodic” is a counter that records the difference
between the current and previous values of an associated 5620 SAM
counter. The OSS equivalent name for a Periodic counter is the name
of the 5620 SAM counter with a “Periodic” suffix. The tables in this
appendix do not list Periodic counters.
Table A-1 lists each statistics package and the associated statistics-counter table.
Table A-1 Statistics packages and counter tables
Package name
See
aclfilter
Table A-2
equipment
Table A-3
ethernetequipment
Table A-4
l2fib
Table A-5
l2fwd
Table A-6
pae802_1x
Table A-7
rtr
Table A-8
service
Table A-9
sitesec
Table A-10
vpls
Table A-11
Table A-2 aclfilter statistics
5620 SAM counter name
Type
MIB counter name
Description
HitCountStats
MIB table name: TIMETRA-FILTER-MIB.tIPFilterParamsTable
Monitored class: aclfilter.IpFilterEntry
(1 of 2)
A-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
egressHitCount
UINT128
tIPFilterParamsEgressHit
Count
This object indicates the number of times
an egress packet matched this entry.
ingressHitCount
UINT128
tIPFilterParamsIngressHit
Count
This object indicates the number of times
an ingress packet matched this entry.
MacHitCountStats
MIB table name: TIMETRA-FILTER-MIB.tMacFilterParamsTable
Monitored class: aclfilter.MacFilterEntry
egressHitCount
UINT128
tMacFilterParamsEgressHi
tCount
This object indicates the number of times
an egress packet matched this entry.
ingressHitCount
UINT128
tMacFilterParamsIngressH
itCount
This object indicates the number of times
an ingress packet matched this entry.
(2 of 2)
Table A-3 equipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AllocatedMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryPoolAllocated
Monitored class: equipment.SystemStatsHolder
allocatedMemory
long
sgiMemoryPoolAllocated
The value of sgiMemoryPoolAllocated
indicates the total memory currently
allocated in memory-pools on the system.
This memory may or may not be currently
in use, but is pre-allocated should the
software need to use it.
AvailableMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryAvailable
Monitored class: equipment.SystemStatsHolder
availableMemory
long
sgiMemoryAvailable
The value of sgiMemoryAvailable
indicates the amount of free memory in
the overall system that is not allocated to
memory pools, but is available in case a
memory pool needs to grow.
InterfaceAdditionalStats
MIB table name: IF-MIB.ifXTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
receivedBroadcastPackets
UINT128
ifHCInBroadcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a broadcast address at
this sub-layer. This object is a 64-bit
version of ifInBroadcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
(1 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-3
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedMulticastPackets
UINT128
ifHCInMulticastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a multicast address at
this sub-layer. For a MAC layer protocol,
this includes both Group and Functional
addresses. This object is a 64-bit version
of ifInMulticastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedTotalOctets
UINT128
ifHCInOctets
The total number of octets received on
the interface, including framing
characters. This object is a 64-bit version
of ifInOctets. Discontinuities in the value
of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedUnicastPackets
UINT128
ifHCInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer. This
object is a 64-bit version of ifInUcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
transmittedBroadcastPackets
UINT128
ifHCOutBroadcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a broadcast address at this sub-layer,
including those that were discarded or not
sent. This object is a 64-bit version of
ifOutBroadcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedMulticastPackets
UINT128
ifHCOutMulticastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a multicast address at this sub-layer,
including those that were discarded or not
sent. For a MAC layer protocol, this
includes both Group and Functional
addresses. This object is a 64-bit version
of ifOutMulticastPkts. Discontinuities in
the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedTotalOctets
UINT128
ifHCOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. This object is a 64-bit version
of ifOutOctets. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
(2 of 7)
A-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmittedUnicastPackets
UINT128
ifHCOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent. This
object is a 64-bit version of
ifOutUcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
InterfaceStats
MIB table name: IF-MIB.ifTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
outboundBadPackets
long
ifOutErrors
For packet-oriented interfaces, the
number of outbound packets that could
not be transmitted because of errors. For
character-oriented or fixed-length
interfaces, the number of outbound
transmission units that could not be
transmitted because of errors.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
outboundPacketsDiscarded
long
ifOutDiscards
The number of outbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being transmitted. One possible
reason for discarding such a packet could
be to free up buffer space. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedBadPackets
long
ifInErrors
For packet-oriented interfaces, the
number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol. For character- oriented or
fixed-length interfaces, the number of
inbound transmission units that contained
errors preventing them from being
deliverable to a higher-layer protocol.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
(3 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-5
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedOctets
long
ifInOctets
The total number of octets received on
the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
receivedPacketsDiscarded
long
ifInDiscards
The number of inbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being deliverable to a higher-layer
protocol. One possible reason for
discarding such a packet could be to free
up buffer space. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedUnicastPackets
long
ifInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedUnknownProtocolPackets
long
ifInUnknownProtos
For packet-oriented interfaces, the
number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
For character-oriented or fixed-length
interfaces that support protocol
multiplexing the number of transmission
units received via the interface which
were discarded because of an unknown or
unsupported protocol. For any interface
that does not support protocol
multiplexing, this counter will always be
0. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedOctets
long
ifOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
(4 of 7)
A-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmittedUnicastPackets
long
ifOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
MediaIndependentStats
MIB table name: HC-RMON-MIB.mediaIndependentTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dropEvents
long
mediaIndependentDropEv
ents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
droppedFrames
long
mediaIndependentDropp
edFrames
The total number of frames which were
received by the probe and therefore not
accounted for in the
mediaIndependentDropEvents, but for
which the probe chose not to count for
this entry for whatever reason. Most
often, this event occurs when the probe is
out of some resources and decides to shed
load from this collection. This count does
not include packets that were not
counted because they had MAC-layer
errors. Note that, unlike the dropEvents
counter, this number is the exact number
of frames dropped.
duplex
int
mediaIndependentDuplex
Mode
The current mode of this link. Note that if
the link has full-duplex capabilities but is
operating in half-duplex mode, this value
will be halfduplex(1).
duplexChanges
long
mediaIndependentDuplex
Changes
The number of times this link has changed
from full-duplex mode to half-duplex
mode or from half-duplex mode to
full-duplex mode.
inputSpeed
long
mediaIndependentInputS
peed
The nominal maximum speed in kilobits
per second of this half-duplex link or on
the inbound connection of this full-duplex
link. If the speed is unknown or there is no
fixed maximum (e.g. a compressed link),
this value shall be zero.
outputSpeed
long
mediaIndependentOutput
Speed
The nominal maximum speed in kilobits
per second of this full-duplex link in the
direction of the network. If the speed is
unknown, the link is half-duplex, or there
is no fixed maximum (e.g. a compressed
link), this value shall be zero.
(5 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-7
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedBadPackets
long
mediaIndependentInError
s
The total number of bad packets received
on a half-duplex link or on the inbound
connection of a full-duplex link.
receivedNonUnicastPackets
UINT128
mediaIndependentInNUC
astHighCapacityPkts
The total number of non-unicast packets
(including bad packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
receivedOctets
UINT128
mediaIndependentInHigh
CapacityOctets
The total number of octets of data
(including those in bad packets) received
(excluding framing bits but including FCS
octets) on a half-duplex link or on the
inbound connection of a full-duplex link.
receivedPackets
UINT128
mediaIndependentInHigh
CapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
transmittedBadPackets
long
mediaIndependentOutErr
ors
The total number of bad packets received
on a full-duplex link in the direction of the
network.
transmittedNonUnicastPackets
UINT128
mediaIndependentOutNU
CastHighCapacityPkts
The total number of packets (including
bad packets) received on a full-duplex
link in the direction of the network.
transmittedOctets
UINT128
mediaIndependentOutHig
hCapacityOctets
The total number of octets of data
(including those in bad packets) received
on a full-duplex link in the direction of the
network (excluding framing bits but
including FCS octets).
transmittedPackets
UINT128
mediaIndependentOutHig
hCapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
full-duplex link in the direction of the
network.
SystemCpuStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiCpuUsage
Monitored class: equipment.SystemStatsHolder
systemCpuUsage
long
sgiCpuUsage
The value of sgiCpuUsage indicates the
current CPU utilization for the system.
SystemMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryUsed
Monitored class: equipment.SystemStatsHolder
systemMemoryUsage
long
sgiMemoryUsed
The value of sgiMemoryUsed indicates the
total pre-allocated pool memory
currently in use on the system.
UplinkPortNetIngressStats
MIB table name: TIMETRA-SAS-PORT-MIB.tmnxSASPortNetIngressStatsTable
Monitored class: equipment.PhysicalPort
portNetIngressFwdInProfOcts
UINT128
tmnxSASPortNetIngressF
wdInProfOcts
tmnxSASPortNetIngressFwdInProfOcts
indicates the number of conforming
network ingress octets forwarded on this
port using this meter.
(6 of 7)
A-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portNetIngressFwdInProfPkts
UINT128
tmnxSASPortNetIngressF
wdInProfPkts
tmnxSASPortNetIngressFwdInProfPkts
indicates the number of conforming
network ingress packets forwarded on this
port using this meter.
portNetIngressFwdOutProfOcts
UINT128
tmnxSASPortNetIngressF
wdOutProfOcts
tmnxSASPortNetIngressFwdOutProfOcts
indicates the number of exceeding
network ingress octets forwarded on this
port using this meter.
portNetIngressFwdOutProfPkts
UINT128
tmnxSASPortNetIngressF
wdOutProfPkts
tmnxSASPortNetIngressFwdOutProfPkts
indicates the number of exceeding
network ingress packets forwarded on this
port using this meter.
portNetIngressMeterIndex
long
tmnxSASPortNetIngressM
eterIndex
tmnxSASPortNetIngressQueueIndex serves
as the tertiary index. When used in
conjunction with tmnxChassisIndex and
tmnxPortPortID, it uniquely identifies a
network ingress meter for the specified
port in the managed system.
(7 of 7)
Table A-4 ethernetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AdditionalEthernetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortEtherTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
highCapacityPackets1519toMaxFra
meSize
UINT128
tmnxPortEtherHCPkts151
9toMax
The total number of packets (including
bad packets) received that were between
1519 octets in length and the maximum
frame size, usually 12287 octets inclusive
(excluding framing bits but including FCS
octets). The lower 32-bits of this 64-bit
counter will equal the value of
tmnxPortEtherPkt1519toMax. The high
32-bits of this counter will equal the value
of tmnxPortEtherHCOverPkts1519toMax.
packets1519toMaxFrameSize
long
tmnxPortEtherPkts1519to
Max
The total number of packets received that
were longer than 1518 octets but less than
the maximum frame size for the
particular medium, usually 12287 octets
(excluding framing bits, but including FCS
octets) and were otherwise well formed.
Dot3Stats
MIB table name: EtherLike-MIB.dot3StatsTable
Monitored class: equipment.PhysicalPort
(1 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-9
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
alignmentErrors
long
dot3StatsAlignmentErrors
A count of frames received on a particular
interface that are not an integral number
of octets in length and do not pass the FCS
check. The count represented by an
instance of this object is incremented
when the alignmentError status is
returned by the MAC service to the LLC (or
other MAC user). Received frames for
which multiple error conditions pertain
are, according to the conventions of IEEE
802.3 Layer Management, counted
exclusively according to the error status
presented to the LLC. This counter does
not increment for group encoding
schemes greater than 4 bits per group. For
interfaces operating at 10 Gb/s, this
counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsAlignmentErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.1.1.7,
aAlignmentErrors.
carrierSenseErrors
long
dot3StatsCarrierSenseErr
ors
The number of times that the carrier
sense condition was lost or never asserted
when attempting to transmit a frame on a
particular interface. The count
represented by an instance of this object
is incremented at most once per
transmission attempt, even if the carrier
sense condition fluctuates during a
transmission attempt. This counter does
not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.13,
aCarrierSenseErrors.
(2 of 13)
A-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
deferredTransmissions
long
dot3StatsDeferredTransm
issions
A count of frames for which the first
transmission attempt on a particular
interface is delayed because the medium
is busy. The count represented by an
instance of this object does not include
frames involved in collisions. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.9,
aFramesWithDeferredXmissions.
duplex
int
dot3StatsDuplexStatus
The current mode of operation of the MAC
entity. 'unknown' indicates that the
current duplex mode could not be
determined. Management control of the
duplex mode is accomplished through the
MAU MIB. When an interface does not
support autonegotiation, or when
autonegotiation is not enabled, the
duplex mode is controlled using
ifMauDefaultType. When autonegotiation
is supported and enabled, duplex mode is
controlled using
ifMauAutoNegAdvertisedBits. In either
case, the currently operating duplex
mode is reflected both in this object and
in ifMauType. Note that this object
provides redundant information with
ifMauType. Normally, redundant objects
are discouraged. However, in this
instance, it allows a management
application to determine the duplex
status of an interface without having to
know every possible value of ifMauType.
This was felt to be sufficiently valuable to
justify the redundancy. REFERENCE [IEEE
802.3 Std.], 30.3.1.1.32, aDuplexStatus.
excessiveCollisions
long
dot3StatsExcessiveCollisi
ons
A count of frames for which transmission
on a particular interface fails due to
excessive collisions. This counter does not
increment when the interface is operating
in full-duplex mode. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.11,
aFramesAbortedDueToXSColls.
(3 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-11
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
fcsErrors
long
dot3StatsFCSErrors
A count of frames received on a particular
interface that are an integral number of
octets in length but do not pass the FCS
check. This count does not include frames
received with frame-too-long or
frame-too-short error. The count
represented by an instance of this object
is incremented when the
frameCheckError status is returned by the
MAC service to the LLC (or other MAC
user). Received frames for which multiple
error conditions pertain are, according to
the conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. Note: Coding errors detected by
the physical layer for speeds above 10
Mb/s will cause the frame to fail the FCS
check. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 5 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the dot3HCStatsFCSErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.6,
aFrameCheckSequenceErrors.
frameTooLongs
long
dot3StatsFrameTooLongs
A count of frames received on a particular
interface that exceed the maximum
permitted frame size. The count
represented by an instance of this object
is incremented when the frameTooLong
status is returned by the MAC service to
the LLC (or other MAC user). Received
frames for which multiple error
conditions pertain are, according to the
conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 80 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsFrameTooLongs object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.25, aFrameTooLongErrors.
(4 of 13)
A-12
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
internalMacReceiveErrors
long
dot3StatsInternalMacRec
eiveErrors
A count of frames for which reception on
a particular interface fails due to an
internal MAC sublayer receive error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsFrameTooLongs object, the
dot3StatsAlignmentErrors object, or the
dot3StatsFCSErrors object. The precise
meaning of the count represented by an
instance of this object is implementationspecific. In particular, an instance of this
object may represent a count of receive
errors on a particular interface that are
not otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacReceiveErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.15,
aFramesLostDueToIntMACRcvError.
internalMacTransmitErrors
long
dot3StatsInternalMacTran
smitErrors
A count of frames for which transmission
on a particular interface fails due to an
internal MAC sublayer transmit error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsLateCollisions object, the
dot3StatsExcessiveCollisions object, or
the dot3StatsCarrierSenseErrors object.
The precise meaning of the count
represented by an instance of this object
is implementation- specific. In particular,
an instance of this object may represent a
count of transmission errors on a
particular interface that are not
otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacTransmitErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.12,
aFramesLostDueToIntMACXmitError.
(5 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-13
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
lateCollisions
long
dot3StatsLateCollisions
The number of times that a collision is
detected on a particular interface later
than one slotTime into the transmission of
a packet. A (late) collision included in a
count represented by an instance of this
object is also considered as a (generic)
collision for purposes of other
collision-related statistics. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.10,
aLateCollisions.
multipleCollisionFrames
long
dot3StatsMultipleCollisio
nFrames
A count of frames that are involved in
more than one collision and are
subsequently transmitted successfully. A
frame that is counted by an instance of
this object is also counted by the
corresponding instance of either the
ifOutUcastPkts, ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsSingleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.4,
aMultipleCollisionFrames.
singleCollisionFrames
long
dot3StatsSingleCollisionF
rames
A count of frames that are involved in a
single collision, and are subsequently
transmitted successfully. A frame that is
counted by an instance of this object is
also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsMultipleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.3,
aSingleCollisionFrames.
(6 of 13)
A-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sqeTestErrors
long
dot3StatsSQETestErrors
A count of times that the SQE TEST ERROR
is received on a particular interface. The
SQE TEST ERROR is set in accordance with
the rules for verification of the SQE
detection mechanism in the PLS Carrier
Sense Function as described in IEEE Std.
802.3, 2000 Edition, section 7.2.4.6. This
counter does not increment on interfaces
operating at speeds greater than 10 Mb/s,
or on interfaces operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 7.2.4.6, also
30.3.2.1.4, aSQETestErrors.
(7 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-15
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
symbolErrors
long
dot3StatsSymbolErrors
For an interface operating at 100 Mb/s,
the number of times there was an invalid
data symbol when a valid carrier was
present. For an interface operating in
half-duplex mode at 1000 Mb/s, the
number of times the receiving media is
non-idle (a carrier event) for a period of
time equal to or greater than slotTime,
and during which there was at least one
occurrence of an event that causes the
PHY to indicate 'Data reception error' or
'carrier extend error' on the GMII. For an
interface operating in full-duplex mode at
1000 Mb/s, the number of times the
receiving media is non-idle (a carrier
event) for a period of time equal to or
greater than minFrameSize, and during
which there was at least one occurrence
of an event that causes the PHY to
indicate 'Data reception error' on the
GMII. For an interface operating at 10
Gb/s, the number of times the receiving
media is non-idle (a carrier event) for a
period of time equal to or greater than
minFrameSize, and during which there
was at least one occurrence of an event
that causes the PHY to indicate 'Receive
Error' on the XGMII. The count
represented by an instance of this object
is incremented at most once per carrier
event, even if multiple symbol errors
occur during the carrier event. This count
does not increment if a collision is
present. This counter does not increment
when the interface is operating at 10
Mb/s. For interfaces operating at 10 Gb/s,
this counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsSymbolErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.2.1.5,
aSymbolErrorDuringCarrier.
EthernetHighCapacityStats
MIB table name: HC-RMON-MIB.etherStatsHighCapacityTable
Monitored classes:
• equipment.PhysicalPort
• equipment.ManagementPort
packets1024to1518Octets
UINT128
etherStatsHighCapacityPk
ts1024to1518Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
(8 of 13)
A-16
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
packets128to255Octets
UINT128
etherStatsHighCapacityPk
ts128to255Octets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
UINT128
etherStatsHighCapacityPk
ts256to511Octets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
UINT128
etherStatsHighCapacityPk
ts512to1023Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
UINT128
etherStatsHighCapacityPk
ts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
UINT128
etherStatsHighCapacityPk
ts65to127Octets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(9 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-17
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
UINT128
etherStatsHighCapacityO
ctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). If the network
is half-duplex Fast Ethernet, this object
can be used as a reasonable estimate of
utilization. If greater precision is desired,
the etherStatsHighCapacityPkts and
etherStatsHighCapacityOctets objects
should be sampled before and after a
common interval. The differences in the
sampled values are Pkts and Octets,
respectively, and the number of seconds
in the interval is Interval. These values
are used to calculate the Utilization as
follows: Pkts * (.96 + .64) + (Octets * .08)
Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent. This table is not
appropriate for monitoring full-duplex
ethernets. If the network is a full-duplex
ethernet and the mediaIndependentTable
is monitoring that network, the utilization
can be calculated as follows: 1)
Determine the utilization of the inbound
path by using the appropriate equation
(for ethernet or fast ethernet) to
determine the utilization, substituting
mediaIndependentInPkts for
etherStatsHighCapacityPkts, and
mediaIndependentInOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization inUtilization. 2)
Determine the utilization of the outbound
path by using the same equation to
determine the utilization, substituting
mediaIndependentOutPkts for
etherStatsHighCapacityPkts, and
mediaIndependentOutOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization outUtilization. 3) The
utilization is the maximum of inUtilization
and outUtilization. This metric shows the
amount of percentage of bandwidth that
is left before congestion will be
experienced on the link.
totalPackets
UINT128
etherStatsHighCapacityPk
ts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
etherStatsBroadcastPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
EthernetStats
MIB table name: RMON-MIB.etherStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
broadcastPackets
long
(10 of 13)
A-18
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
etherStatsCollisions
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the
location of the RMON probe. Section
8.2.1.3 (10BASE-5) and section 10.3.1.3
(10BASE-2) of IEEE standard 802.3 states
that a station must detect a collision, in
the receive mode, if three or more
stations are transmitting simultaneously.
A repeater port must detect a collision
when two or more stations are
transmitting simultaneously. Thus a probe
placed on a repeater port could record
more collisions than a probe connected to
a station on the same segment would.
Probe location plays a much smaller role
when considering 10BASE-T. 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments
to which the repeater is connected.
crcAlignErrors
long
etherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
etherStatsDropEvents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
etherStatsFragments
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(11 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-19
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
etherStatsJabbers
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different than the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
where any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPackets
long
etherStatsMulticastPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
oversizePackets
long
etherStatsOversizePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
packets1024to1518Octets
long
etherStatsPkts1024to151
8Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets128to255Octets
long
etherStatsPkts128to255O
ctets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
long
etherStatsPkts256to511O
ctets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
long
etherStatsPkts512to1023
Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
long
etherStatsPkts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
long
etherStatsPkts65to127Oc
tets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(12 of 13)
A-20
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
long
etherStatsOctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
10-Megabit ethernet utilization. If greater
precision is desired, the etherStatsPkts
and etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent.
totalPackets
long
etherStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
undersizePackets
long
etherStatsUndersizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
(13 of 13)
Table A-5 l2fib statistics
5620 SAM counter name
Type
MIB counter name
Description
MFibGrpSrcStats
MIB table name: TIMETRA-SERV-MIB.tlsMFibGrpSrcStatsTable
Monitored class: l2fib.MFibGrpSrc
forwardedOctets
UINT128
tlsMFibGrpSrcStatsForwar
dedOctets
tlsMFibGrpSrcStatsForwardedOctets
indicates the number of octets that were
forwarded to the SAPs and SDPs listed in
the tlsMFibInfoTable.
forwardedPkts
UINT128
tlsMFibGrpSrcStatsForwar
dedPkts
tlsMFibGrpSrcStatsForwardedPkts
indicates the number of IPv4 multicast
packets that were forwarded to the SAPs
and SDPs listed in the tlsMFibInfoTable.
Table A-6 l2fwd statistics
5620 SAM counter name
Type
MIB counter name
Description
AccessInterfaceStpStats
MIB table name: TIMETRA-SERV-MIB.sapTlsInfoTable
Monitored class: l2fwd.AccessInterfaceStp
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-21
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
forwardTransitions
long
sapTlsStpForwardTransiti
ons
The value of the object
sapTlsStpForwardTransitions indicates
the number of times this port has
transitioned from the Learning state to
the Forwarding state.
inBadBpdus
long
sapTlsStpInBadBpdus
This object specifies the number of bad
BPDUs received on this SAP.
inConfigBpdus
long
sapTlsStpInConfigBpdus
The value of the object
sapTlsStpInConfigBpdus indicates the
number of Configuration BPDUs received
on this SAP.
inRapidSpanningTreeBpdus
long
sapTlsStpInRstBpdus
The value of the object
sapTlsStpInRstBpdus indicates the number
of Rapid Spanning Tree (RST) BPDUs
received on this SAP.
inTcnBpdus
long
sapTlsStpInTcnBpdus
The value of the object
sapTlsStpInTcnBpdus indicates the
number of Topology Change Notification
BPDUs received on this SAP.
outConfigBpdus
long
sapTlsStpOutConfigBpdus
The value of the object
sapTlsStpOutConfigBpdus indicates the
number of Configuration BPDUs sent out
this SAP.
outRapidSpanningTreeBpdus
long
sapTlsStpOutRstBpdus
The value of the object
sapTlsStpOutRstBpdus indicates the
number of Rapid Spanning Tree (RST)
BPDUs sent out on this SAP.
outTcnBpdus
long
sapTlsStpOutTcnBpdus
This object specifies the number of
Topology Change Notification BPDUs sent
out this SAP.
(2 of 2)
Table A-7 pae802_1x statistics
5620 SAM counter name
Type
MIB counter name
Description
PaePortAuthenticatorDiagStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthDiagTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dot1xAuthAuthEapLogoffWhileAut
henticated
long
dot1xAuthAuthEapLogoff
WhileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to DISCONNECTED, as a
result of an EAPOL-Logoff message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.12.
dot1xAuthAuthEapLogoffWhileAut
henticating
long
dot1xAuthAuthEapLogoff
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of an EAPOL-Logoff message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.9.
(1 of 5)
A-22
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthAuthEapStartsWhileAuth
enticated
long
dot1xAuthAuthEapStarts
WhileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to CONNECTING, as a
result of an EAPOL-Start message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.11.
dot1xAuthAuthEapStartsWhileAuth
enticating
long
dot1xAuthAuthEapStarts
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of an EAPOL-Start message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.8.
dot1xAuthAuthFailWhileAuthentic
ating
long
dot1xAuthAuthFailWhileA
uthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to HELD, as a result of
the Backend Authentication state
machine indicating authentication failure
(authFail = TRUE). REFERENCE 9.4.2,
8.5.4.2.6.
dot1xAuthAuthReauthsWhileAuthe
nticated
long
dot1xAuthAuthReauthsW
hileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to CONNECTING, as a
result of a reauthentication request
(reAuthenticate = TRUE). REFERENCE
9.4.2, 8.5.4.2.10.
dot1xAuthAuthReauthsWhileAuthe
nticating
long
dot1xAuthAuthReauthsW
hileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of a reauthentication request
(reAuthenticate = TRUE). REFERENCE
9.4.2, 8.5.4.2.7.
dot1xAuthAuthSuccessWhileAuthe
nticating
long
dot1xAuthAuthSuccessWh
ileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to AUTHENTICATED, as
a result of the Backend Authentication
state machine indicating successful
authentication of the Supplicant
(authSuccess = TRUE). REFERENCE 9.4.2,
8.5.4.2.4.
dot1xAuthAuthTimeoutsWhileAuth
enticating
long
dot1xAuthAuthTimeouts
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of the Backend Authentication
state machine indicating authentication
timeout (authTimeout = TRUE).
REFERENCE 9.4.2, 8.5.4.2.5.
dot1xAuthBackendAccessChalleng
es
long
dot1xAuthBackendAccess
Challenges
Counts the number of times that the state
machine receives an initial
Access-Challenge packet from the
Authentication server (i.e., aReq
becomes TRUE, causing exit from the
RESPONSE state). Indicates that the
Authentication Server has communication
with the Authenticator. REFERENCE 9.4.2,
8.5.6.2.2.
(2 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-23
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthBackendAuthFails
long
dot1xAuthBackendAuthFa
ils
Counts the number of times that the state
machine receives an EAP-Failure message
from the Authentication Server (i.e., aFail
becomes TRUE, causing a transition from
RESPONSE to FAIL). Indicates that the
Supplicant has not authenticated to the
Authentication Server. REFERENCE 9.4.2,
8.5.6.2.6.
dot1xAuthBackendAuthSuccesses
long
dot1xAuthBackendAuthSu
ccesses
Counts the number of times that the state
machine receives an EAP-Success message
from the Authentication Server (i.e.,
aSuccess becomes TRUE, causing a
transition from RESPONSE to SUCCESS).
Indicates that the Supplicant has
successfully authenticated to the
Authentication Server. REFERENCE 9.4.2,
8.5.6.2.5.
dot1xAuthBackendNonNakRespons
esFromSupplicant
long
dot1xAuthBackendNonNa
kResponsesFromSupplica
nt
Counts the number of times that the state
machine receives a response from the
Supplicant to an initial EAP-Request, and
the response is something other than
EAP-NAK (i.e., rxResp becomes TRUE,
causing the state machine to transition
from REQUEST to RESPONSE, and the
response is not an EAP-NAK). Indicates
that the Supplicant can respond to the
Authenticator's chosen EAP-method.
REFERENCE 9.4.2, 8.5.6.2.4.
dot1xAuthBackendOtherRequestsT
oSupplicant
long
dot1xAuthBackendOtherR
equestsToSupplicant
Counts the number of times that the state
machine sends an EAP-Request packet
(other than an Identity, Notification,
Failure or Success message) to the
Supplicant (i.e., executes txReq on entry
to the REQUEST state). Indicates that the
Authenticator chose an EAP-method.
REFERENCE 9.4.2, 8.5.6.2.3.
dot1xAuthBackendResponses
long
dot1xAuthBackendRespon
ses
Counts the number of times that the state
machine sends an initial Access-Request
packet to the Authentication server (i.e.,
executes sendRespToServer on entry to
the RESPONSE state). Indicates that the
Authenticator attempted communication
with the Authentication Server.
REFERENCE 9.4.2, 8.5.6.2.1.
dot1xAuthEapLogoffsWhileConnec
ting
long
dot1xAuthEapLogoffsWhil
eConnecting
Counts the number of times that the state
machine transitions from CONNECTING to
DISCONNECTED as a result of receiving an
EAPOL-Logoff message. REFERENCE 9.4.2,
8.5.4.2.2.
dot1xAuthEntersAuthenticating
long
dot1xAuthEntersAuthenti
cating
Counts the number of times that the state
machine transitions from CONNECTING to
AUTHENTICATING, as a result of an
EAP-Response/Identity message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.3.
dot1xAuthEntersConnecting
long
dot1xAuthEntersConnecti
ng
Counts the number of times that the state
machine transitions to the CONNECTING
state from any other state. REFERENCE
9.4.2, 8.5.4.2.1.
(3 of 5)
A-24
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
PaePortAuthenticatorSessionStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthSessionStatsTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dot1xAuthSessionAuthenticMethod
int
dot1xAuthSessionAuthent
icMethod
The authentication method used to
establish the session. REFERENCE 9.4.4,
Session Authentication Method.
dot1xAuthSessionFramesRx
long
dot1xAuthSessionFrames
Rx
The number of user data frames received
on this Port during the session.
REFERENCE 9.4.4, Session Frames
Received.
dot1xAuthSessionFramesTx
long
dot1xAuthSessionFrames
Tx
The number of user data frames
transmitted on this Port during the
session. REFERENCE 9.4.4, Session Frames
Transmitted.
dot1xAuthSessionOctetsRx
UINT128
dot1xAuthSessionOctetsR
x
The number of octets received in user
data frames on this Port during the
session. REFERENCE 9.4.4, Session Octets
Received.
dot1xAuthSessionOctetsTx
UINT128
dot1xAuthSessionOctetsT
x
The number of octets transmitted in user
data frames on this Port during the
session. REFERENCE 9.4.4, Session Octets
Transmitted.
dot1xAuthSessionTerminateCause
int
dot1xAuthSessionTermina
teCause
The reason for the session termination.
REFERENCE 9.4.4, Session Terminate
Cause.
dot1xAuthSessionTime
long
dot1xAuthSessionTime
The duration of the session in seconds.
REFERENCE 9.4.4, Session Time.
PaePortAuthenticatorStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
dot1xAuthEapLengthErrorFramesR
x
long
dot1xAuthEapLengthError
FramesRx
The number of EAPOL frames that have
been received by this Authenticator in
which the Packet Body Length field is
invalid. REFERENCE 9.4.2, EAP length
error frames received.
dot1xAuthEapolFramesRx
long
dot1xAuthEapolFramesRx
The number of valid EAPOL frames of any
type that have been received by this
Authenticator. REFERENCE 9.4.2, EAPOL
frames received.
dot1xAuthEapolFramesTx
long
dot1xAuthEapolFramesTx
The number of EAPOL frames of any type
that have been transmitted by this
Authenticator. REFERENCE 9.4.2, EAPOL
frames transmitted.
dot1xAuthEapolLogoffFramesRx
long
dot1xAuthEapolLogoffFra
mesRx
The number of EAPOL Logoff frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Logoff frames
received.
(4 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-25
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthEapolReqFramesTx
long
dot1xAuthEapolReqFrame
sTx
The number of EAP Request frames (other
than Rq/Id frames) that have been
transmitted by this Authenticator.
REFERENCE 9.4.2, EAPOL Request frames
transmitted.
dot1xAuthEapolReqIdFramesTx
long
dot1xAuthEapolReqIdFra
mesTx
The number of EAP Req/Id frames that
have been transmitted by this
Authenticator. REFERENCE 9.4.2, EAPOL
Req/Id frames transmitted.
dot1xAuthEapolRespFramesRx
long
dot1xAuthEapolRespFram
esRx
The number of valid EAP Response frames
(other than Resp/Id frames) that have
been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Response
frames received.
dot1xAuthEapolRespIdFramesRx
long
dot1xAuthEapolRespIdFra
mesRx
The number of EAP Resp/Id frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Resp/Id frames
received.
dot1xAuthEapolStartFramesRx
long
dot1xAuthEapolStartFram
esRx
The number of EAPOL Start frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Start frames
received.
dot1xAuthInvalidEapolFramesRx
long
dot1xAuthInvalidEapolFra
mesRx
The number of EAPOL frames that have
been received by this Authenticator in
which the frame type is not recognized.
REFERENCE 9.4.2, Invalid EAPOL frames
received.
dot1xAuthLastEapolFrameVersion
long
dot1xAuthLastEapolFram
eVersion
The protocol version number carried in
the most recently received EAPOL frame.
REFERENCE 9.4.2, Last EAPOL frame
version.
(5 of 5)
Table A-8 rtr statistics
5620 SAM counter name
Type
MIB counter name
Description
RouteStats
MIB table name: TIMETRA-VRTR-MIB.vRtrStatTable
Monitored classes:
•
•
rtr.VirtualRouter
vprn.Site
activeARPEntries
long
vRtrStatActiveARPEntries
vRtrStatActiveARPEntries indicates the
number of active ARP entries for the
specified virtual router in the system.
directActiveRoutes
long
vRtrDirectActiveRoutes
vRtrDirectActiveRoutes indicates the
current number of active direct routes for
this instance of the route table.
directRoutes
long
vRtrDirectRoutes
vRtrDirectRoutes indicates the current
number of direct routes for this instance
of the route table.
(1 of 2)
A-26
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
routerInterfacesActive
long
vRtrStatActiveIfs
vRtrStatActiveIfs indicates the current
number of router interfaces with
vRtrIfAdminState equal 'inService' on this
virtual router.
routesInVrf
long
vRtrStatCurrNumRoutes
vRtrStatCurrNumRoutes indicates the
current number of routes in the VRF for
this virtual router.
staticActiveRoutes
long
vRtrStaticActiveRoutes
vRtrStaticActiveRoutes indicates the
current number of active static routes for
this instance of the route table.
staticRoutes
long
vRtrStaticRoutes
vRtrStaticRoutes indicates the current
number of static routes for this instance
of the route table.
totalARPEntries
long
vRtrStatTotalARPEntries
vRtrStatTotalARPEntries indicates the
total number of active and inactive ARP
entries for the specified virtual router in
the system.
(2 of 2)
Table A-9 service statistics
5620 SAM counter name
Type
MIB counter name
Description
ServiceSapIngQosPlcyStats
MIB table name: TIMETRA-SAS-QOS-MIB.sapIngQosMeterStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
forwardedInProfOctets
UINT128
sapIngQosMeterStatsForw
ardedInProfOctets
The number of in-profile octets (rate
below CIR) forwarded by the ingress
Qchip.
forwardedInProfPackets
UINT128
sapIngQosMeterStatsForw
ardedInProfPackets
The number of in-profile packets (rate
below CIR) forwarded by the ingress
Qchip.
forwardedOutProfOctets
UINT128
sapIngQosMeterStatsForw
ardedOutProfOctets
The number of out-of-profile octets (rate
above CIR) forwarded by the ingress
Qchip.
forwardedOutProfPackets
UINT128
sapIngQosMeterStatsForw
ardedOutProfPackets
The number of out-of-profile packets
(rate above CIR) forwarded by the ingress
Qchip.
meterId
long
sapIngQosMeterId
The index of the ingress QoS meter of this
SAP.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-27
A. 7210 SAS-E Release 1.0 statistics counters
Table A-10 sitesec statistics
5620 SAM counter name
Type
MIB counter name
Description
MafEntryStats
MIB table name: TIMETRA-SECURITY-MIB.tmnxMafMatchTable
Monitored class: sitesec.MafEntry
matchCount
UINT128
tmnxMafMatchCount
The value of tmnxMafMatchCount
indicates the number of times a
management packet has matched this
filter entry.
Table A-11 vpls statistics
5620 SAM counter name
Type
MIB counter name
Description
L2AccessInterfaceIgmpSnpgErrorStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sapIgmpSnpgStatsTable
Monitored classes:
•
•
•
vpls.AbstractL2AccessInterface
vpls.IL2AccessInterface
mvpls.IL2AccessInterface
sapIgmpSnpgImportPolicyDrops
long
sapIgmpSnpgImportPolicy
Drops
The value of the object
sapIgmpSnpgImportPolicyDrops indicates
the number of times an IGMP Group or
Source is dropped because of applying an
import policy on this SAP.
sapIgmpSnpgMaxNumGroupsDrops
long
sapIgmpSnpgMaxNumGro
upsDrops
The value of the object
sapIgmpSnpgMaxNumGroupsDrops
indicates the number of times an IGMP
Group is dropped because of exceeding
the configured maximum number of
groups on this SAP.
sapIgmpSnpgRxBadEncodedPkts
long
sapIgmpSnpgRxBadEncod
edPkts
The value of the object
sapIgmpSnpgRxBadEncodedPkts indicates
the number of IGMP packets dropped on
this SAP because of a bad encoding.
sapIgmpSnpgRxBadIgmpChksmPkts
long
sapIgmpSnpgRxBadIgmpC
hksmPkts
The value of the object
sapIgmpSnpgRxBadIgmpChksmPkts
indicates the number of dropped IGMP
packets on this SAP because of a bad IGMP
header checksum.
sapIgmpSnpgRxBadIpChksmPkts
long
sapIgmpSnpgRxBadIpChks
mPkts
The value of the object
sapIgmpSnpgRxBadIpChksmPkts indicates
the number of dropped IGMP packets on
this SAP because of a bad IPv4 header
checksum.
sapIgmpSnpgRxBadLenPkts
long
sapIgmpSnpgRxBadLenPkt
s
The value of the object
sapIgmpSnpgRxBadLenPkts indicates the
number of IGMP packets dropped on this
SAP because of a bad length.
(1 of 3)
A-28
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapIgmpSnpgRxNoRtrAlertPkts
long
sapIgmpSnpgRxNoRtrAler
tPkts
The value of the object
sapIgmpSnpgRxNoRtrAlertPkts indicates
the number of IGMP packets dropped on
this SAP because the Router Alert Option
in the IP packet is not set.
sapIgmpSnpgRxWrongVersionPkts
long
sapIgmpSnpgRxWrongVer
sionPkts
The value of the object
sapIgmpSnpgRxWrongVersionPkts
indicates the total number of IGMP
packets with a wrong version received on
this SAP.
sapIgmpSnpgRxZeroSrcAdrPkts
long
sapIgmpSnpgRxZeroSrcAd
rPkts
The value of the object
sapIgmpSnpgRxZeroSrcAdrPkts indicates
the number of IGMP packets dropped on
this SAP because they contain a zero
source IPv4 address.
sapIgmpSnpgSendQueryCfgDrops
long
sapIgmpSnpgSendQueryCf
gDrops
The value of the object
sapIgmpSnpgSendQueryCfgDrops
indicates the number of times an IGMP
Query is dropped because the object
sapIgmpSnpgCfgSendQueries for this SAP
is set to enabled.
L2AccessInterfaceIgmpSnpgStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sapIgmpSnpgStatsTable
Monitored classes:
vpls.AbstractL2AccessInterface
vpls.IL2AccessInterface
mvpls.IL2AccessInterface
•
•
•
sapIgmpSnpgFwdGenQueries
long
sapIgmpSnpgFwdGenQuer
ies
The value of the object
sapIgmpSnpgFwdGenQueries indicates
the number of IGMP General Queries
forwarded on this SAP.
sapIgmpSnpgFwdGrpSpecQueries
long
sapIgmpSnpgFwdGrpSpec
Queries
The value of the object
sapIgmpSnpgFwdGrpSpecQueries
indicates the number of IGMP
Group-Specific Queries forwarded on this
SAP.
sapIgmpSnpgFwdUnknownType
long
sapIgmpSnpgFwdUnknow
nType
The value of the object
sapIgmpSnpgFwdUnknownType indicates
the number of IGMP unknown type
packets forwarded on this SAP.
sapIgmpSnpgFwdV1Reports
long
sapIgmpSnpgFwdV1Repor
ts
The value of the object
sapIgmpSnpgFwdV1Reports indicates the
number of IGMPv1 Reports forwarded on
this SAP.
sapIgmpSnpgFwdV2Leaves
long
sapIgmpSnpgFwdV2Leave
s
The value of the object
sapIgmpSnpgFwdV2Leaves indicates the
number of IGMPv2 Leaves forwarded on
this SAP.
sapIgmpSnpgFwdV2Reports
long
sapIgmpSnpgFwdV2Repor
ts
The value of the object
sapIgmpSnpgFwdV2Reports indicates the
number of IGMPv2 Reports forwarded on
this SAP.
(2 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
A-29
A. 7210 SAS-E Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapIgmpSnpgRxGenQueries
long
sapIgmpSnpgRxGenQueri
es
The value of the object
sapIgmpSnpgRxGenQueries indicates the
number of IGMP General Queries received
on this SAP.
sapIgmpSnpgRxGrpSpecQueries
long
sapIgmpSnpgRxGrpSpecQ
ueries
The value of the object
sapIgmpSnpgRxGrpSpecQueries indicates
the number of IGMP Group-Specific
Queries received on this SAP.
sapIgmpSnpgRxUnknownType
long
sapIgmpSnpgRxUnknownT
ype
The value of the object
sapIgmpSnpgRxUnknownType indicates
the number of IGMP unknown type
packets received on this SAP.
sapIgmpSnpgRxV1Reports
long
sapIgmpSnpgRxV1Reports
The value of the object
sapIgmpSnpgRxV1Reports indicates the
number of IGMPv1 Reports received on
this SAP.
sapIgmpSnpgRxV2Leaves
long
sapIgmpSnpgRxV2Leaves
The value of the object
sapIgmpSnpgRxV2Leaves indicates the
number of IGMPv2 Leaves received on this
SAP.
sapIgmpSnpgRxV2Reports
long
sapIgmpSnpgRxV2Reports
The value of the object
sapIgmpSnpgRxV2Reports indicates the
number of IGMPv2 Reports received on
this SAP.
sapIgmpSnpgTxGenQueries
long
sapIgmpSnpgTxGenQueri
es
The value of the object
sapIgmpSnpgTxGenQueries indicates the
number of IGMP General Queries
transmitted on this SAP.
sapIgmpSnpgTxGrpSpecQueries
long
sapIgmpSnpgTxGrpSpecQ
ueries
The value of the object
sapIgmpSnpgTxGrpSpecQueries indicates
the number of IGMP Group-Specific
Queries transmitted on this SAP.
sapIgmpSnpgTxV1Reports
long
sapIgmpSnpgTxV1Reports
The value of the object
sapIgmpSnpgTxV1Reports indicates the
number of IGMPv1 Reports transmitted on
this SAP.
sapIgmpSnpgTxV2Leaves
long
sapIgmpSnpgTxV2Leaves
The value of the object
sapIgmpSnpgTxV2Leaves indicates the
number of IGMPv2 Leaves transmitted on
this SAP.
sapIgmpSnpgTxV2Reports
long
sapIgmpSnpgTxV2Reports
The value of the object
sapIgmpSnpgTxV2Reports indicates the
number of IGMPv2 Reports transmitted on
this SAP.
(3 of 3)
A-30
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B.
7210 SAS-M Release 1.0 statistics
counters
B.1 7210 SAS-M Release 1.0 statistics counters
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-2
B-1
B. 7210 SAS-M Release 1.0 statistics counters
B.1
7210 SAS-M Release 1.0 statistics counters
This appendix lists in tabular form the statistics counters that the 5620 SAM supports
for the 7210 SAS-M, Release 1.0. Each 5620 SAM counter entry in a table contains
the name and description of the corresponding device MIB counter.
The 5620 SAM counter name in a table entry is the internal counter identifier that is
required for statistics retrieval through the 5620 SAM OSSI. The displayed counter
name in the 5620 SAM GUI is typically an expansion of this identifier. For example,
the receivedBroadcastPackets counter name in the equipment table corresponds to
the Received Broadcast Packets counter name on the Log Record form for an
Ethernet port.
Note 1 — The tables list the 5620 SAM-supported statistics counters
for the current release of the device. Counters that are supported for a
previous device release, but not for the current release, are not listed.
Note 2 — A statistics counter in the 5620 SAM GUI whose displayed
name ends with “Periodic” is a counter that records the difference
between the current and previous values of an associated 5620 SAM
counter. The OSS equivalent name for a Periodic counter is the name
of the 5620 SAM counter with a “Periodic” suffix. The tables in this
appendix do not list Periodic counters.
Table B-1 lists each statistics package and the associated statistics-counter table.
Table B-1 Statistics packages and counter tables
B-2
Package name
See
aclfilter
Table B-2
equipment
Table B-3
ethernetequipment
Table B-4
isis
Table B-5
l2fwd
Table B-6
lag
Table B-7
ldp
Table B-8
mpls
Table B-9
ospf
Table B-10
pae802_1x
Table B-11
rsvp
Table B-12
rtr
Table B-13
service
Table B-14
sitesec
Table B-15
svt
Table B-16
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
Table B-2 aclfilter statistics
5620 SAM counter name
Type
MIB counter name
Description
HitCountStats
MIB table name: TIMETRA-FILTER-MIB.tIPFilterParamsTable
Monitored class: aclfilter.IpFilterEntry
egressHitCount
UINT128
tIPFilterParamsEgressHit
Count
This object indicates the number of times
an egress packet matched this entry.
ingressHitCount
UINT128
tIPFilterParamsIngressHit
Count
This object indicates the number of times
an ingress packet matched this entry.
MacHitCountStats
MIB table name: TIMETRA-FILTER-MIB.tMacFilterParamsTable
Monitored class: aclfilter.MacFilterEntry
egressHitCount
UINT128
tMacFilterParamsEgressHi
tCount
This object indicates the number of times
an egress packet matched this entry.
ingressHitCount
UINT128
tMacFilterParamsIngressH
itCount
This object indicates the number of times
an ingress packet matched this entry.
Table B-3 equipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AllocatedMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryPoolAllocated
Monitored class: equipment.SystemStatsHolder
allocatedMemory
long
sgiMemoryPoolAllocated
The value of sgiMemoryPoolAllocated
indicates the total memory currently
allocated in memory-pools on the system.
This memory may or may not be currently
in use, but is pre-allocated should the
software need to use it.
AvailableMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryAvailable
Monitored class: equipment.SystemStatsHolder
availableMemory
long
sgiMemoryAvailable
The value of sgiMemoryAvailable
indicates the amount of free memory in
the overall system that is not allocated to
memory pools, but is available in case a
memory pool needs to grow.
InterfaceAdditionalStats
MIB table name: IF-MIB.ifXTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
(1 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-3
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedBroadcastPackets
UINT128
ifHCInBroadcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a broadcast address at
this sub-layer. This object is a 64-bit
version of ifInBroadcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedMulticastPackets
UINT128
ifHCInMulticastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a multicast address at
this sub-layer. For a MAC layer protocol,
this includes both Group and Functional
addresses. This object is a 64-bit version
of ifInMulticastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedTotalOctets
UINT128
ifHCInOctets
The total number of octets received on
the interface, including framing
characters. This object is a 64-bit version
of ifInOctets. Discontinuities in the value
of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedUnicastPackets
UINT128
ifHCInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer. This
object is a 64-bit version of ifInUcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
transmittedBroadcastPackets
UINT128
ifHCOutBroadcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a broadcast address at this sub-layer,
including those that were discarded or not
sent. This object is a 64-bit version of
ifOutBroadcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
(2 of 8)
B-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmittedMulticastPackets
UINT128
ifHCOutMulticastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a multicast address at this sub-layer,
including those that were discarded or not
sent. For a MAC layer protocol, this
includes both Group and Functional
addresses. This object is a 64-bit version
of ifOutMulticastPkts. Discontinuities in
the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedTotalOctets
UINT128
ifHCOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. This object is a 64-bit version
of ifOutOctets. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedUnicastPackets
UINT128
ifHCOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent. This
object is a 64-bit version of
ifOutUcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
InterfaceStats
MIB table name: IF-MIB.ifTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
outboundBadPackets
long
ifOutErrors
For packet-oriented interfaces, the
number of outbound packets that could
not be transmitted because of errors. For
character-oriented or fixed-length
interfaces, the number of outbound
transmission units that could not be
transmitted because of errors.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
(3 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-5
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
outboundPacketsDiscarded
long
ifOutDiscards
The number of outbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being transmitted. One possible
reason for discarding such a packet could
be to free up buffer space. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedBadPackets
long
ifInErrors
For packet-oriented interfaces, the
number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol. For character- oriented or
fixed-length interfaces, the number of
inbound transmission units that contained
errors preventing them from being
deliverable to a higher-layer protocol.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedOctets
long
ifInOctets
The total number of octets received on
the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
receivedPacketsDiscarded
long
ifInDiscards
The number of inbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being deliverable to a higher-layer
protocol. One possible reason for
discarding such a packet could be to free
up buffer space. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedUnicastPackets
long
ifInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
(4 of 8)
B-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedUnknownProtocolPackets
long
ifInUnknownProtos
For packet-oriented interfaces, the
number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
For character-oriented or fixed-length
interfaces that support protocol
multiplexing the number of transmission
units received via the interface which
were discarded because of an unknown or
unsupported protocol. For any interface
that does not support protocol
multiplexing, this counter will always be
0. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedOctets
long
ifOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedUnicastPackets
long
ifOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
MediaIndependentStats
MIB table name: HC-RMON-MIB.mediaIndependentTable
Monitored classes:
• equipment.PhysicalPort
• equipment.ManagementPort
dropEvents
long
mediaIndependentDropEv
ents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
droppedFrames
long
mediaIndependentDropp
edFrames
The total number of frames which were
received by the probe and therefore not
accounted for in the
mediaIndependentDropEvents, but for
which the probe chose not to count for
this entry for whatever reason. Most
often, this event occurs when the probe is
out of some resources and decides to shed
load from this collection. This count does
not include packets that were not
counted because they had MAC-layer
errors. Note that, unlike the dropEvents
counter, this number is the exact number
of frames dropped.
(5 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-7
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
duplex
int
mediaIndependentDuplex
Mode
The current mode of this link. Note that if
the link has full-duplex capabilities but is
operating in half-duplex mode, this value
will be halfduplex(1).
duplexChanges
long
mediaIndependentDuplex
Changes
The number of times this link has changed
from full-duplex mode to half-duplex
mode or from half-duplex mode to
full-duplex mode.
inputSpeed
long
mediaIndependentInputS
peed
The nominal maximum speed in kilobits
per second of this half-duplex link or on
the inbound connection of this full-duplex
link. If the speed is unknown or there is no
fixed maximum (e.g. a compressed link),
this value shall be zero.
outputSpeed
long
mediaIndependentOutput
Speed
The nominal maximum speed in kilobits
per second of this full-duplex link in the
direction of the network. If the speed is
unknown, the link is half-duplex, or there
is no fixed maximum (e.g. a compressed
link), this value shall be zero.
receivedBadPackets
long
mediaIndependentInError
s
The total number of bad packets received
on a half-duplex link or on the inbound
connection of a full-duplex link.
receivedNonUnicastPackets
UINT128
mediaIndependentInNUC
astHighCapacityPkts
The total number of non-unicast packets
(including bad packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
receivedOctets
UINT128
mediaIndependentInHigh
CapacityOctets
The total number of octets of data
(including those in bad packets) received
(excluding framing bits but including FCS
octets) on a half-duplex link or on the
inbound connection of a full-duplex link.
receivedPackets
UINT128
mediaIndependentInHigh
CapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
transmittedBadPackets
long
mediaIndependentOutErr
ors
The total number of bad packets received
on a full-duplex link in the direction of the
network.
transmittedNonUnicastPackets
UINT128
mediaIndependentOutNU
CastHighCapacityPkts
The total number of packets (including
bad packets) received on a full-duplex
link in the direction of the network.
transmittedOctets
UINT128
mediaIndependentOutHig
hCapacityOctets
The total number of octets of data
(including those in bad packets) received
on a full-duplex link in the direction of the
network (excluding framing bits but
including FCS octets).
transmittedPackets
UINT128
mediaIndependentOutHig
hCapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
full-duplex link in the direction of the
network.
(6 of 8)
B-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
PortAccessEgressQueueStats
MIB table name: TIMETRA-SAS-PORT-MIB.tmnxPortAccessEgressQueueStatsTable
Monitored class: equipment.PhysicalPort
portAccessEgressQueueStatsDroOc
ts
UINT128
tmnxPortAccessEgressQu
eueStatsDroOcts
tmnxPortAccessEgressQueueStatsDroOcts
indicates the number of dropped network
egress octets on this port using this
queue.
portAccessEgressQueueStatsDroPk
ts
UINT128
tmnxPortAccessEgressQu
eueStatsDroPkts
tmnxPortAccessEgressQueueStatsDroPkts
indicates the number of dropped access
egress packets on this port using this
queue.
portAccessEgressQueueStatsFwdO
cts
UINT128
tmnxPortAccessEgressQu
eueStatsFwdOcts
tmnxPortAccessEgressQueueStatsFwdOct
s indicates the number of forward access
egress octets forwarded on this port using
this queue.
portAccessEgressQueueStatsFwdPk
ts
UINT128
tmnxPortAccessEgressQu
eueStatsFwdPkts
tmnxPortAccessEgressQueueStatsFwdPkts
indicates the number of forwarded access
egress packets forwarded on this port
using this queue.
portAccessEgressQueueStatsIndex
long
tmnxPortAccessEgressQu
eueStatsIndex
tmnxPortAccessEgressQueueIndex serves
as the tertiary index. When used in
conjunction with tmnxChassisIndex and
tmnxPortPortID, it uniquely identifies a
access egress queue for the specified port
in the managed system.
PortNetEgressQueueStats
MIB table name: TIMETRA-SAS-PORT-MIB.tmnxPortNetEgressQueueStatsTable
Monitored class: equipment.PhysicalPort
portNetEgressQueueStatsDroOcts
UINT128
tmnxPortNetEgressQueue
StatsDroOcts
tmnxPortNetEgressQueueStatsDroOcts
indicates the number of dropped network
egress octets on this port using this
queue.
portNetEgressQueueStatsDroPkts
UINT128
tmnxPortNetEgressQueue
StatsDroPkts
tmnxPortNetEgressQueueStatsDroPkts
indicates the number of dropped network
egress packets on this port using this
queue.
portNetEgressQueueStatsFwdOcts
UINT128
tmnxPortNetEgressQueue
StatsFwdOcts
tmnxPortNetEgressQueueStatsFwdOcts
indicates the number of forwarded
network egress octets on this port using
this queue.
portNetEgressQueueStatsFwdPkts
UINT128
tmnxPortNetEgressQueue
StatsFwdPkts
tmnxPortNetEgressQueueStatsFwdPkts
indicates the number of forwarded
network egress packets on this port using
this queue.
portNetEgressQueueStatsIndex
long
tmnxPortNetEgressQueue
StatsIndex
tmnxPortNetEgressQueueStatsIndex
serves as the tertiary index. When used in
conjunction with tmnxChassisIndex and
tmnxPortPortID, it uniquely identifies a
network egress queue for the specified
port in the managed system.
PortNetIngressStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortNetIngressStatsTable
Monitored class: equipment.PhysicalPort
(7 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-9
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
inProfileOctetsDropped
UINT128
tmnxPortNetIngressDroIn
ProfOcts
tmnxPortNetIngressDroInProfOcts
indicates the number of conforming
network ingress octets dropped on this
port using this queue.
inProfileOctetsForwarded
UINT128
tmnxPortNetIngressFwdIn
ProfOcts
tmnxPortNetIngressFwdInProfOcts
indicates the number of conforming
network ingress octets forwarded on this
port using this queue.
inProfilePacketsDropped
UINT128
tmnxPortNetIngressDroIn
ProfPkts
tmnxPortNetIngressDroInProfPkts
indicates the number of conforming
network ingress packets dropped on this
port using this queue.
inProfilePacketsForwarded
UINT128
tmnxPortNetIngressFwdIn
ProfPkts
tmnxPortNetIngressFwdInProfPkts
indicates the number of conforming
network ingress packets forwarded on this
port using this queue.
outOfProfileOctetsDropped
UINT128
tmnxPortNetIngressDroO
utProfOcts
tmnxPortNetIngressDroOutProfOcts
indicates the number of exceeding
network ingress octets dropped on this
port using this queue.
outOfProfileOctetsForwarded
UINT128
tmnxPortNetIngressFwdO
utProfOcts
tmnxPortNetIngressFwdOutProfOcts
indicates the number of exceeding
network ingress octets forwarded on this
port using this queue.
outOfProfilePacketsDropped
UINT128
tmnxPortNetIngressDroO
utProfPkts
tmnxPortNetIngressDroOutProfPkts
indicates the number of exceeding
network ingress packets dropped on this
port using this queue.
outOfProfilePacketsForwarded
UINT128
tmnxPortNetIngressFwdO
utProfPkts
tmnxPortNetIngressFwdOutProfPkts
indicates the number of exceeding
network ingress packets forwarded on this
port using this queue.
SystemCpuStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiCpuUsage
Monitored class: equipment.SystemStatsHolder
systemCpuUsage
long
sgiCpuUsage
The value of sgiCpuUsage indicates the
current CPU utilization for the system.
SystemMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryUsed
Monitored class: equipment.SystemStatsHolder
systemMemoryUsage
long
sgiMemoryUsed
The value of sgiMemoryUsed indicates the
total pre-allocated pool memory
currently in use on the system.
(8 of 8)
B-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
Table B-4 ethernetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AdditionalEthernetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortEtherTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
highCapacityPackets1519toMaxFra
meSize
UINT128
tmnxPortEtherHCPkts151
9toMax
The total number of packets (including
bad packets) received that were between
1519 octets in length and the maximum
frame size, usually 12287 octets inclusive
(excluding framing bits but including FCS
octets). The lower 32-bits of this 64-bit
counter will equal the value of
tmnxPortEtherPkt1519toMax. The high
32-bits of this counter will equal the value
of tmnxPortEtherHCOverPkts1519toMax.
packets1519toMaxFrameSize
long
tmnxPortEtherPkts1519to
Max
The total number of packets received that
were longer than 1518 octets but less than
the maximum frame size for the
particular medium, usually 12287 octets
(excluding framing bits, but including FCS
octets) and were otherwise well formed.
dot3StatsAlignmentErrors
A count of frames received on a particular
interface that are not an integral number
of octets in length and do not pass the FCS
check. The count represented by an
instance of this object is incremented
when the alignmentError status is
returned by the MAC service to the LLC (or
other MAC user). Received frames for
which multiple error conditions pertain
are, according to the conventions of IEEE
802.3 Layer Management, counted
exclusively according to the error status
presented to the LLC. This counter does
not increment for group encoding
schemes greater than 4 bits per group. For
interfaces operating at 10 Gb/s, this
counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsAlignmentErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.1.1.7,
aAlignmentErrors.
Dot3Stats
MIB table name: EtherLike-MIB.dot3StatsTable
Monitored class: equipment.PhysicalPort
alignmentErrors
long
(1 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-11
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
carrierSenseErrors
long
dot3StatsCarrierSenseErr
ors
The number of times that the carrier
sense condition was lost or never asserted
when attempting to transmit a frame on a
particular interface. The count
represented by an instance of this object
is incremented at most once per
transmission attempt, even if the carrier
sense condition fluctuates during a
transmission attempt. This counter does
not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.13,
aCarrierSenseErrors.
deferredTransmissions
long
dot3StatsDeferredTransm
issions
A count of frames for which the first
transmission attempt on a particular
interface is delayed because the medium
is busy. The count represented by an
instance of this object does not include
frames involved in collisions. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.9,
aFramesWithDeferredXmissions.
duplex
int
dot3StatsDuplexStatus
The current mode of operation of the MAC
entity. 'unknown' indicates that the
current duplex mode could not be
determined. Management control of the
duplex mode is accomplished through the
MAU MIB. When an interface does not
support autonegotiation, or when
autonegotiation is not enabled, the
duplex mode is controlled using
ifMauDefaultType. When autonegotiation
is supported and enabled, duplex mode is
controlled using
ifMauAutoNegAdvertisedBits. In either
case, the currently operating duplex
mode is reflected both in this object and
in ifMauType. Note that this object
provides redundant information with
ifMauType. Normally, redundant objects
are discouraged. However, in this
instance, it allows a management
application to determine the duplex
status of an interface without having to
know every possible value of ifMauType.
This was felt to be sufficiently valuable to
justify the redundancy. REFERENCE [IEEE
802.3 Std.], 30.3.1.1.32, aDuplexStatus.
(2 of 15)
B-12
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
excessiveCollisions
long
dot3StatsExcessiveCollisi
ons
A count of frames for which transmission
on a particular interface fails due to
excessive collisions. This counter does not
increment when the interface is operating
in full-duplex mode. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.11,
aFramesAbortedDueToXSColls.
fcsErrors
long
dot3StatsFCSErrors
A count of frames received on a particular
interface that are an integral number of
octets in length but do not pass the FCS
check. This count does not include frames
received with frame-too-long or
frame-too-short error. The count
represented by an instance of this object
is incremented when the
frameCheckError status is returned by the
MAC service to the LLC (or other MAC
user). Received frames for which multiple
error conditions pertain are, according to
the conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. Note: Coding errors detected by
the physical layer for speeds above 10
Mb/s will cause the frame to fail the FCS
check. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 5 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the dot3HCStatsFCSErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.6,
aFrameCheckSequenceErrors.
(3 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-13
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
frameTooLongs
long
dot3StatsFrameTooLongs
A count of frames received on a particular
interface that exceed the maximum
permitted frame size. The count
represented by an instance of this object
is incremented when the frameTooLong
status is returned by the MAC service to
the LLC (or other MAC user). Received
frames for which multiple error
conditions pertain are, according to the
conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 80 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsFrameTooLongs object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.25, aFrameTooLongErrors.
internalMacReceiveErrors
long
dot3StatsInternalMacRec
eiveErrors
A count of frames for which reception on
a particular interface fails due to an
internal MAC sublayer receive error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsFrameTooLongs object, the
dot3StatsAlignmentErrors object, or the
dot3StatsFCSErrors object. The precise
meaning of the count represented by an
instance of this object is implementationspecific. In particular, an instance of this
object may represent a count of receive
errors on a particular interface that are
not otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacReceiveErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.15,
aFramesLostDueToIntMACRcvError.
(4 of 15)
B-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
internalMacTransmitErrors
long
dot3StatsInternalMacTran
smitErrors
A count of frames for which transmission
on a particular interface fails due to an
internal MAC sublayer transmit error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsLateCollisions object, the
dot3StatsExcessiveCollisions object, or
the dot3StatsCarrierSenseErrors object.
The precise meaning of the count
represented by an instance of this object
is implementation- specific. In particular,
an instance of this object may represent a
count of transmission errors on a
particular interface that are not
otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacTransmitErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.12,
aFramesLostDueToIntMACXmitError.
lateCollisions
long
dot3StatsLateCollisions
The number of times that a collision is
detected on a particular interface later
than one slotTime into the transmission of
a packet. A (late) collision included in a
count represented by an instance of this
object is also considered as a (generic)
collision for purposes of other
collision-related statistics. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.10,
aLateCollisions.
(5 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-15
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
multipleCollisionFrames
long
dot3StatsMultipleCollisio
nFrames
A count of frames that are involved in
more than one collision and are
subsequently transmitted successfully. A
frame that is counted by an instance of
this object is also counted by the
corresponding instance of either the
ifOutUcastPkts, ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsSingleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.4,
aMultipleCollisionFrames.
singleCollisionFrames
long
dot3StatsSingleCollisionF
rames
A count of frames that are involved in a
single collision, and are subsequently
transmitted successfully. A frame that is
counted by an instance of this object is
also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsMultipleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.3,
aSingleCollisionFrames.
sqeTestErrors
long
dot3StatsSQETestErrors
A count of times that the SQE TEST ERROR
is received on a particular interface. The
SQE TEST ERROR is set in accordance with
the rules for verification of the SQE
detection mechanism in the PLS Carrier
Sense Function as described in IEEE Std.
802.3, 2000 Edition, section 7.2.4.6. This
counter does not increment on interfaces
operating at speeds greater than 10 Mb/s,
or on interfaces operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 7.2.4.6, also
30.3.2.1.4, aSQETestErrors.
(6 of 15)
B-16
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
symbolErrors
long
dot3StatsSymbolErrors
For an interface operating at 100 Mb/s,
the number of times there was an invalid
data symbol when a valid carrier was
present. For an interface operating in
half-duplex mode at 1000 Mb/s, the
number of times the receiving media is
non-idle (a carrier event) for a period of
time equal to or greater than slotTime,
and during which there was at least one
occurrence of an event that causes the
PHY to indicate 'Data reception error' or
'carrier extend error' on the GMII. For an
interface operating in full-duplex mode at
1000 Mb/s, the number of times the
receiving media is non-idle (a carrier
event) for a period of time equal to or
greater than minFrameSize, and during
which there was at least one occurrence
of an event that causes the PHY to
indicate 'Data reception error' on the
GMII. For an interface operating at 10
Gb/s, the number of times the receiving
media is non-idle (a carrier event) for a
period of time equal to or greater than
minFrameSize, and during which there
was at least one occurrence of an event
that causes the PHY to indicate 'Receive
Error' on the XGMII. The count
represented by an instance of this object
is incremented at most once per carrier
event, even if multiple symbol errors
occur during the carrier event. This count
does not increment if a collision is
present. This counter does not increment
when the interface is operating at 10
Mb/s. For interfaces operating at 10 Gb/s,
this counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsSymbolErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.2.1.5,
aSymbolErrorDuringCarrier.
EthernetHighCapacityStats
MIB table name: HC-RMON-MIB.etherStatsHighCapacityTable
Monitored classes:
• equipment.PhysicalPort
• equipment.ManagementPort
packets1024to1518Octets
UINT128
etherStatsHighCapacityPk
ts1024to1518Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
(7 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-17
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
packets128to255Octets
UINT128
etherStatsHighCapacityPk
ts128to255Octets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
UINT128
etherStatsHighCapacityPk
ts256to511Octets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
UINT128
etherStatsHighCapacityPk
ts512to1023Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
UINT128
etherStatsHighCapacityPk
ts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
UINT128
etherStatsHighCapacityPk
ts65to127Octets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(8 of 15)
B-18
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
UINT128
etherStatsHighCapacityO
ctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). If the network
is half-duplex Fast Ethernet, this object
can be used as a reasonable estimate of
utilization. If greater precision is desired,
the etherStatsHighCapacityPkts and
etherStatsHighCapacityOctets objects
should be sampled before and after a
common interval. The differences in the
sampled values are Pkts and Octets,
respectively, and the number of seconds
in the interval is Interval. These values
are used to calculate the Utilization as
follows: Pkts * (.96 + .64) + (Octets * .08)
Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent. This table is not
appropriate for monitoring full-duplex
ethernets. If the network is a full-duplex
ethernet and the mediaIndependentTable
is monitoring that network, the utilization
can be calculated as follows: 1)
Determine the utilization of the inbound
path by using the appropriate equation
(for ethernet or fast ethernet) to
determine the utilization, substituting
mediaIndependentInPkts for
etherStatsHighCapacityPkts, and
mediaIndependentInOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization inUtilization. 2)
Determine the utilization of the outbound
path by using the same equation to
determine the utilization, substituting
mediaIndependentOutPkts for
etherStatsHighCapacityPkts, and
mediaIndependentOutOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization outUtilization. 3) The
utilization is the maximum of inUtilization
and outUtilization. This metric shows the
amount of percentage of bandwidth that
is left before congestion will be
experienced on the link.
totalPackets
UINT128
etherStatsHighCapacityPk
ts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
etherStatsBroadcastPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
EthernetStats
MIB table name: RMON-MIB.etherStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
broadcastPackets
long
(9 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-19
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
etherStatsCollisions
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the
location of the RMON probe. Section
8.2.1.3 (10BASE-5) and section 10.3.1.3
(10BASE-2) of IEEE standard 802.3 states
that a station must detect a collision, in
the receive mode, if three or more
stations are transmitting simultaneously.
A repeater port must detect a collision
when two or more stations are
transmitting simultaneously. Thus a probe
placed on a repeater port could record
more collisions than a probe connected to
a station on the same segment would.
Probe location plays a much smaller role
when considering 10BASE-T. 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments
to which the repeater is connected.
crcAlignErrors
long
etherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
etherStatsDropEvents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
etherStatsFragments
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(10 of 15)
B-20
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
etherStatsJabbers
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different than the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
where any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPackets
long
etherStatsMulticastPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
oversizePackets
long
etherStatsOversizePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
packets1024to1518Octets
long
etherStatsPkts1024to151
8Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets128to255Octets
long
etherStatsPkts128to255O
ctets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
long
etherStatsPkts256to511O
ctets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
long
etherStatsPkts512to1023
Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
long
etherStatsPkts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
long
etherStatsPkts65to127Oc
tets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(11 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-21
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
long
etherStatsOctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
10-Megabit ethernet utilization. If greater
precision is desired, the etherStatsPkts
and etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent.
totalPackets
long
etherStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
undersizePackets
long
etherStatsUndersizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
QosDroppedOctetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngrMdaQosStatTable
Monitored class: equipment.PhysicalPort
qosClassifier0DroppedOctets
UINT128
tmnxPortIngrMdaQos00St
atDropOcts
tmnxPortIngrMdaQos00StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier10DroppedOctets
UINT128
tmnxPortIngrMdaQos10St
atDropOcts
tmnxPortIngrMdaQos10StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier11DroppedOctets
UINT128
tmnxPortIngrMdaQos11St
atDropOcts
tmnxPortIngrMdaQos11StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier12DroppedOctets
UINT128
tmnxPortIngrMdaQos12St
atDropOcts
tmnxPortIngrMdaQos12StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier13DroppedOctets
UINT128
tmnxPortIngrMdaQos13St
atDropOcts
tmnxPortIngrMdaQos13StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(12 of 15)
B-22
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier14DroppedOctets
UINT128
tmnxPortIngrMdaQos14St
atDropOcts
tmnxPortIngrMdaQos14StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier15DroppedOctets
UINT128
tmnxPortIngrMdaQos15St
atDropOcts
tmnxPortIngrMdaQos15StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier1DroppedOctets
UINT128
tmnxPortIngrMdaQos01St
atDropOcts
tmnxPortIngrMdaQos01StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier2DroppedOctets
UINT128
tmnxPortIngrMdaQos02St
atDropOcts
tmnxPortIngrMdaQos02StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier3DroppedOctets
UINT128
tmnxPortIngrMdaQos03St
atDropOcts
tmnxPortIngrMdaQos03StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier4DroppedOctets
UINT128
tmnxPortIngrMdaQos04St
atDropOcts
tmnxPortIngrMdaQos04StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier5DroppedOctets
UINT128
tmnxPortIngrMdaQos05St
atDropOcts
tmnxPortIngrMdaQos05StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier6DroppedOctets
UINT128
tmnxPortIngrMdaQos06St
atDropOcts
tmnxPortIngrMdaQos06StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier7DroppedOctets
UINT128
tmnxPortIngrMdaQos07St
atDropOcts
tmnxPortIngrMdaQos07StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier8DroppedOctets
UINT128
tmnxPortIngrMdaQos08St
atDropOcts
tmnxPortIngrMdaQos08StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier9DroppedOctets
UINT128
tmnxPortIngrMdaQos09St
atDropOcts
tmnxPortIngrMdaQos09StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(13 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-23
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
QosDroppedPacketStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngrMdaQosStatTable
Monitored class: equipment.PhysicalPort
qosClassifier0DroppedPackets
UINT128
tmnxPortIngrMdaQos00St
atDropPkts
tmnxPortIngrMdaQos00StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier10DroppedPackets
UINT128
tmnxPortIngrMdaQos10St
atDropPkts
tmnxPortIngrMdaQos10StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier11DroppedPackets
UINT128
tmnxPortIngrMdaQos11St
atDropPkts
tmnxPortIngrMdaQos11StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier12DroppedPackets
UINT128
tmnxPortIngrMdaQos12St
atDropPkts
tmnxPortIngrMdaQos12StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier13DroppedPackets
UINT128
tmnxPortIngrMdaQos13St
atDropPkts
tmnxPortIngrMdaQos13StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier14DroppedPackets
UINT128
tmnxPortIngrMdaQos14St
atDropPkts
tmnxPortIngrMdaQos14StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier15DroppedPackets
UINT128
tmnxPortIngrMdaQos15St
atDropPkts
tmnxPortIngrMdaQos15StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier1DroppedPackets
UINT128
tmnxPortIngrMdaQos01St
atDropPkts
tmnxPortIngrMdaQos01StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier2DroppedPackets
UINT128
tmnxPortIngrMdaQos02St
atDropPkts
tmnxPortIngrMdaQos02StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier3DroppedPackets
UINT128
tmnxPortIngrMdaQos03St
atDropPkts
tmnxPortIngrMdaQos03StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(14 of 15)
B-24
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier4DroppedPackets
UINT128
tmnxPortIngrMdaQos04St
atDropPkts
tmnxPortIngrMdaQos04StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier5DroppedPackets
UINT128
tmnxPortIngrMdaQos05St
atDropPkts
tmnxPortIngrMdaQos05StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier6DroppedPackets
UINT128
tmnxPortIngrMdaQos06St
atDropPkts
tmnxPortIngrMdaQos06StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier7DroppedPackets
UINT128
tmnxPortIngrMdaQos07St
atDropPkts
tmnxPortIngrMdaQos07StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier8DroppedPackets
UINT128
tmnxPortIngrMdaQos08St
atDropPkts
tmnxPortIngrMdaQos08StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier9DroppedPackets
UINT128
tmnxPortIngrMdaQos09St
atDropPkts
tmnxPortIngrMdaQos09StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(15 of 15)
Table B-5 isis statistics
5620 SAM counter name
Type
MIB counter name
Description
InterfaceLevelOneReceivingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelOneConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
(1 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-25
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
InterfaceLevelOneSendingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelOneConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelTwoReceivingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelTwoConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelTwoSendingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelTwoConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
LinkStatePduSiteStats
MIB table name: TIMETRA-ISIS-MIB.vRtrIsisStatsTable
Monitored class: isis.Site
(2 of 4)
B-26
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
csnpDropped
long
vRtrIsisCSNPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisCSNPDrop.
csnpReceived
long
vRtrIsisCSNPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisCSNPRecd.
csnpRetransmitted
long
vRtrIsisCSNPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisCSNPRetrans.
csnpSent
long
vRtrIsisCSNPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisCSNPSent.
helloDropped
long
vRtrIsisIIHDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisIIHDrop.
helloReceived
long
vRtrIsisIIHRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisIIHRecd.
helloRetransmitted
long
vRtrIsisIIHRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisIIHRetrans.
helloSent
long
vRtrIsisIIHSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisIIHSent.
lspDropped
long
vRtrIsisLSPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisLSPDrop.
lspReceived
long
vRtrIsisLSPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisLSPRecd.
lspRetransmitted
long
vRtrIsisLSPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisLSPRetrans.
lspSent
long
vRtrIsisLSPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisLSPSent.
psnpDropped
long
vRtrIsisPSNPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisPSNPDrop.
psnpReceived
long
vRtrIsisPSNPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisPSNPRecd.
psnpRetransmitted
long
vRtrIsisPSNPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisPSNPRetrans.
psnpSent
long
vRtrIsisPSNPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisPSNPSent.
(3 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-27
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
unknownDropped
long
vRtrIsisUnknownDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisUnknownDrop.
unknownReceived
long
vRtrIsisUnknownRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisUnknownRecd.
unknownRetransmitted
long
vRtrIsisUnknownRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisUnknownRetrans.
unknownSent
long
vRtrIsisUnknownSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisUnknownSent.
SiteStats
MIB table name: TIMETRA-ISIS-MIB.vRtrIsisStatsTable
Monitored class: isis.Site
cspfDroppedRequests
long
vRtrIsisCSPFDroppedRequ
ests
vRtrIsisCSPFDroppedRequests maintains
the number of dropped CSPF requests by
the protocol.
cspfPathsFound
long
vRtrIsisCSPFPathsFound
vRtrIsisCSPFPathsFound maintains the
number of responses to CSPF requests for
which paths satisfying the constraints
were found.
cspfPathsNotFound
long
vRtrIsisCSPFPathsNotFoun
d
vRtrIsisCSPFPathsFound maintains the
number of responses to CSPF requests for
which no paths satisfying the constraints
were found.
cspfRequests
long
vRtrIsisCSPFRequests
vRtrIsisCSPFRequests maintains the
number of CSPF requests made to the
protocol.
initiatedPurges
long
vRtrIsisInitiatedPurges
The value of vRtrIsisInitiatedPurges
counts the number of times purges have
been initiated.
lspRegenerations
long
vRtrIsisLSPRegenerations
The value of vRtrIsisLSPRegenerations
maintains the count of LSP regenerations.
spfRuns
long
vRtrIsisSpfRuns
The value of vRtrIsisSpfRuns specifies the
number of times shortest path first
calculations have been made.
(4 of 4)
Table B-6 l2fwd statistics
5620 SAM counter name
Type
MIB counter name
Description
AccessInterfaceStpStats
MIB table name: TIMETRA-SERV-MIB.sapTlsInfoTable
Monitored class: l2fwd.AccessInterfaceStp
(1 of 3)
B-28
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
forwardTransitions
long
sapTlsStpForwardTransiti
ons
The value of the object
sapTlsStpForwardTransitions indicates
the number of times this port has
transitioned from the Learning state to
the Forwarding state.
inBadBpdus
long
sapTlsStpInBadBpdus
This object specifies the number of bad
BPDUs received on this SAP.
inConfigBpdus
long
sapTlsStpInConfigBpdus
The value of the object
sapTlsStpInConfigBpdus indicates the
number of Configuration BPDUs received
on this SAP.
inRapidSpanningTreeBpdus
long
sapTlsStpInRstBpdus
The value of the object
sapTlsStpInRstBpdus indicates the number
of Rapid Spanning Tree (RST) BPDUs
received on this SAP.
inTcnBpdus
long
sapTlsStpInTcnBpdus
The value of the object
sapTlsStpInTcnBpdus indicates the
number of Topology Change Notification
BPDUs received on this SAP.
outConfigBpdus
long
sapTlsStpOutConfigBpdus
The value of the object
sapTlsStpOutConfigBpdus indicates the
number of Configuration BPDUs sent out
this SAP.
outRapidSpanningTreeBpdus
long
sapTlsStpOutRstBpdus
The value of the object
sapTlsStpOutRstBpdus indicates the
number of Rapid Spanning Tree (RST)
BPDUs sent out on this SAP.
outTcnBpdus
long
sapTlsStpOutTcnBpdus
This object specifies the number of
Topology Change Notification BPDUs sent
out this SAP.
CircuitStpStats
MIB table name: TIMETRA-SERV-MIB.sdpBindTlsTable
Monitored class: l2fwd.CircuitStp
forwardTransitions
long
sdpBindTlsStpForwardTra
nsitions
The value of the object
sdpBindTlsStpForwardTransitions
indicates the number of times this port
has transitioned from the Learning state
to the Forwarding state.
inBadBpdus
long
sdpBindTlsStpInBadBpdus
The value of the object
sdpBindTlsStpInBadBpdus indicates the
number of bad BPDUs received on this SDP
Bind.
inConfigBpdus
long
sdpBindTlsStpInConfigBpd
us
The value of the object
sdpBindTlsStpInConfigBpdus indicates the
number of Configuration BPDUs received
on this SDP Bind.
inRapidSpanningTreeBpdus
long
sdpBindTlsStpInRstBpdus
The value of the object
sdpBindTlsStpInRstBpdus indicates the
number of Rapid Spanning Tree (Rst)
BPDUs received on this SDP.
inTcnBpdus
long
sdpBindTlsStpInTcnBpdus
The value of the object
sdpBindTlsStpInTcnBpdus indicates the
number of Topology Change Notification
BPDUs received on this SDP Bind.
(2 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-29
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
outConfigBpdus
long
sdpBindTlsStpOutConfigB
pdus
The value of the object
sdpBindTlsStpOutConfigBpdus indicates
the number of Configuration BPDUs sent
out this SDP Bind.
outRapidSpanningTreeBpdus
long
sdpBindTlsStpOutRstBpdu
s
The value of the object
sdpBindTlsStpOutRstBpdus indicates the
number of Rapid Spanning Tree (Rstp)
BPDUs sent out on this SDP.
outTcnBpdus
long
sdpBindTlsStpOutTcnBpd
us
The value of the object
sdpBindTlsStpOutTcnBpdus indicates the
number of Topology Change Notification
BPDUs sent out this SDP Bind.
SiteFibStats
MIB table name: TIMETRA-SERV-MIB.svcTlsInfoTable
Monitored class: l2fwd.SiteFib
entries
long
svcTlsFdbNumEntries
The value of the object
svcTlsFdbNumEntries indicates the
current number of entries in the FDB of
this service.
provisionedSize
long
svcTlsFdbTableSize
The value of the object
svcTlsFdbTableSize specifies the
maximum number of learned and static
entries allowed in the FDB of this service.
When the value of
TIMETRA-CHASSIS-MIB::tmnxChassisOper
Mode is not 'c', the maximum value of
svcTlsFdbTableSize is '131071'. DEFVAL {
250 }.
staticEntries
long
svcTlsFdbNumStaticEntri
es
The value of the object
svcTlsFdbNumStaticEntries indicates the
current number of static entries in the
FDB of this service.
SiteStpStats
MIB table name: TIMETRA-SERV-MIB.svcTlsInfoTable
Monitored class: l2fwd.SiteStp
timeSinceTopologyChange
long
svcTlsStpTimeSinceTopol
ogyChange
The value of the object
svcTlsStpTimeSinceTopologyChange
indicates the time (in hundredths of a
second) since the last time a topology
change was detected by the Spanning
Tree Protocol instance associated with
this service.
topologyChanges
long
svcTlsStpTopologyChange
s
The value of the object
svcTlsStpTopologyChanges indicates the
total number of topology changes
detected by the Spanning Tree Protocol
instance associated with this service since
the management entity was last reset or
initialized.
(3 of 3)
B-30
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
Table B-7 lag statistics
5620 SAM counter name
Type
MIB counter name
Description
LagStats
MIB table name: TIMETRA-LAG-MIB.tLagOperationTable
Monitored class: lag.Interface
portThresholdFalling
long
tLagPortThresholdFalling
counts the number of linkDown or
dynamicCost events for the Link
Aggregation Group caused by the number
of physical ports being less than or equal
to tLagPortThreshold value.
portThresholdRising
long
tLagPortThresholdRising
counts the number of linkUp or
dynamicCost events for the Link
Aggregation Group caused by the number
of physical ports being greater than
tLagPortThreshold value.
Table B-8 ldp statistics
5620 SAM counter name
Type
MIB counter name
Description
SessionStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpSessionStatsTable
Monitored class: ldp.Session
addressMessagesReceived
long
vRtrLdpSessStatsAddrIn
The value of vRtrLdpSessStatsAddrIn
counts the number of Address Messages
that have been received during this
session.
addressMessagesSent
long
vRtrLdpSessStatsAddrOut
The value of vRtrLdpSessStatsAddrOut
counts the number of Address Messages
that have been sent during this session.
addressWithdrawMessagesReceive
d
long
vRtrLdpSessStatsAddrWit
hdrawIn
The value of
vRtrLdpSessStatsAddrWithdrawIn counts
the number of Address Withdraw
Messages that have been received during
this session.
addressWithdrawMessagesSent
long
vRtrLdpSessStatsAddrWit
hdrawOut
The value of
vRtrLdpSessStatsAddrWithdrawOut counts
the number of Address Withdraw
Messages that have been sent during this
session.
fecReceived
long
vRtrLdpSessStatsFECRecv
The value of vRtrLdpSessStatsFECRecv
counts the number of FECs received for
this session.
fecSent
long
vRtrLdpSessStatsFECSent
The value of vRtrLdpSessStatsFECSent
counts the number of FECs sent for this
session.
helloMessagesReceived
long
vRtrLdpSessStatsHelloIn
The value of vRtrLdpSessStatsHelloIn
counts the number of Hello Messages that
have been received during this session.
(1 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-31
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
helloMessagesSent
long
vRtrLdpSessStatsHelloOut
The value of vRtrLdpSessStatsHelloOut
counts the number of Hello Messages that
have been sent during this session.
initMessagesReceived
long
vRtrLdpSessStatsInitIn
The value of vRtrLdpSessStatsInitIn counts
the number of Init Messages that have
been received during this session.
initMessagesSent
long
vRtrLdpSessStatsInitOut
The value of vRtrLdpSessStatsInitOut
counts the number of Init Messages that
have been sent during this session.
keepAliveMessagesReceived
long
vRtrLdpSessStatsKeepaliv
eIn
The value of vRtrLdpSessStatsKeepaliveIn
counts the number of Keepalive Messages
that have been received during this
session.
keepAliveMessagesSent
long
vRtrLdpSessStatsKeepaliv
eOut
The value of
vRtrLdpSessStatsKeepaliveOut counts the
number of Keepalive Messages that have
been sent during this session.
labelAbortsReceived
long
vRtrLdpSessStatsLabelAb
ortIn
The value of
vRtrLdpSessStatsLabelAbortIn counts the
number of Label Abort Messages that have
been received during this session.
labelAbortsSent
long
vRtrLdpSessStatsLabelAb
ortOut
The value of
vRtrLdpSessStatsLabelAbortOut counts
the number of Label Abort Messages that
have been sent during this session.
labelMappingsReceived
long
vRtrLdpSessStatsLabelMa
ppingIn
The value of
vRtrLdpSessStatsLabelMappingIn counts
the number of Label Mapping Messages
that have been received during this
session.
labelMappingsSent
long
vRtrLdpSessStatsLabelMa
ppingOut
The value of
vRtrLdpSessStatsLabelMappingOut counts
the number of Label Mapping Messages
that have been sent during this session.
labelReleasesReceived
long
vRtrLdpSessStatsLabelRel
easeIn
The value of
vRtrLdpSessStatsLabelReleaseIn counts
the number of Label Release Messages
that have been received during this
session.
labelReleasesSent
long
vRtrLdpSessStatsLabelRel
easeOut
The value of
vRtrLdpSessStatsLabelReleaseOut counts
the number of Label Release Messages
that have been sent during this session.
labelRequestsReceived
long
vRtrLdpSessStatsLabelRe
questIn
The value of
vRtrLdpSessStatsLabelRequestIn counts
the number of Label Request Messages
that have been received during this
session.
labelRequestsSent
long
vRtrLdpSessStatsLabelRe
questOut
The value of
vRtrLdpSessStatsLabelRequestOut counts
the number of Label Request Messages
that have been sent during this session.
(2 of 5)
B-32
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
labelWithdrawsReceived
long
vRtrLdpSessStatsLabelWit
hdrawIn
The value of
vRtrLdpSessStatsLabelWithdrawIn counts
the number of Label Withdraw Messages
that have been received during this
session.
labelWithdrawsSent
long
vRtrLdpSessStatsLabelWit
hdrawOut
The value of
vRtrLdpSessStatsLabelWithdrawOut
counts the number of Label Withdraw
Messages that have been sent during this
session.
linkAdjacencies
long
vRtrLdpSessStatsLinkAdj
The value of vRtrLdpSessStatsLinkAdj
specifies the number of link adjacencies
for this session.
notificationMessagesReceived
long
vRtrLdpSessStatsNotificat
ionIn
The value of
vRtrLdpSessStatsNotificationIn counts the
number of Notification Messages that
have been received during this session.
notificationMessagesSent
long
vRtrLdpSessStatsNotificat
ionOut
The value of
vRtrLdpSessStatsNotificationOut counts
the number of Notification Messages that
have been sent during this session.
targetedAdjacencies
long
vRtrLdpSessStatsTargAdj
The value of vRtrLdpSessStatsTargAdj
specifies the number of targeted
adjacencies for this session.
SiteStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpStatsTable
Monitored class: ldp.Site
activeAdjacencies
long
vRtrLdpStatsActiveAdjac
encies
The value of
vRtrLdpStatsActiveAdjacencies specifies
the number of active adjacencies (i.e.
established sessions) associated with the
LDP instance.
activeInterfaces
long
vRtrLdpStatsActiveInterfa
ces
The value of vRtrLdpStatsActiveInterfaces
specifies the number of active (i.e.
operationally up) interfaces associated
with the LDP instance.
activeSessions
long
vRtrLdpStatsActiveSessio
ns
The value of vRtrLdpStatsActiveSessions
specifies the number of active sessions
(i.e. session in some form of creation)
associated with the LDP instance.
activeTargetedSessions
long
vRtrLdpStatsActiveTargSe
ssions
The value of
vRtrLdpStatsActiveTargSessions specifies
the number of active (i.e. operationally
up) targeted sessions associated with the
LDP instance.
addressFECsReceived
long
vRtrLdpStatsAddrFECRecv
The value of vRtrLdpStatsAddrFECRecv
specifies the number of Address FECs
received by the LDP instance from its
neighbors.
addressFECsSent
long
vRtrLdpStatsAddrFECSent
The value of vRtrLdpStatsAddrFECSent
specifies the number of Address FECs sent
by the LDP instance to its neighbors.
(3 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-33
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
attemptedSessions
long
vRtrLdpStatsAttemptedSe
ssions
The value of
vRtrLdpStatsAttemptedSessions specifies
the total number of attempted sessions
for this LDP instance.
badLdpIdentifierErrors
long
vRtrLdpStatsBadLdpIdenti
fierErrors
The value of
vRtrLdpStatsBadLdpIdentifierErrors gives
the number of Bad LDP Identifier Fatal
Errors detected for sessions associated
with this LDP instance. REFERENCE LDP
Specification, Section 3.5.1.2.
badMessageLengthErrors
long
vRtrLdpStatsBadMessageL
engthErrors
The value of
vRtrLdpStatsBadMessageLengthErrors
gives the number of Bad Message Length
Fatal Errors detected for sessions
associated with this LDP instance.
REFERENCE LDP Specification, Section
3.5.1.2.
badPduLengthErrors
long
vRtrLdpStatsBadPduLengt
hErrors
The value of
vRtrLdpStatsBadPduLengthErrors gives
the number of Bad Pdu Length Fatal Errors
detected for sessions associated with this
LDP instance. REFERENCE LDP
Specification, Section 3.5.1.2.
badTlvLengthErrors
long
vRtrLdpStatsBadTlvLengt
hErrors
The value of
vRtrLdpStatsBadTlvLengthErrors gives the
number of Bad TLV Length Fatal Errors
detected for sessions associated with this
LDP instance. REFERENCE LDP
Specification, Section 3.5.1.2.
inactiveInterfaces
long
vRtrLdpStatsInactiveInter
faces
The value of
vRtrLdpStatsInactiveInterfaces specifies
the number of inactive (i.e. operationally
down) interfaces associated with the LDP
instance.
inactiveTargetedSessions
long
vRtrLdpStatsInactiveTarg
Sessions
The value of
vRtrLdpStatsInactiveTargSessions
specifies the number of inactive (i.e.
operationally down) targeted sessions
associated with the LDP instance.
keepAliveExpiredErrors
long
vRtrLdpStatsKeepAliveEx
piredErrors
The value of
vRtrLdpStatsKeepAliveExpiredErrors gives
the number of Session Keep Alive Timer
Expired Errors detected for sessions
associated with this LDP instance.
REFERENCE LDP Specification, Section
3.5.1.2.
malformedTlvValueErrors
long
vRtrLdpStatsMalformedTl
vValueErrors
The value of
vRtrLdpStatsMalformedTlvValueErrors
gives the number of Malformed TLV Value
Fatal Errors detected for sessions
associated with this LDP instance.
REFERENCE LDP Specification, Section
3.5.1.2.
operDownEvents
long
vRtrLdpStatsOperDownEv
ents
The value of
vRtrLdpStatsOperDownEvents specifies
the number of times the LDP instance has
gone operationally down since the
instance was created.
(4 of 5)
B-34
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
serviceFECsReceived
long
vRtrLdpStatsSvcFECRecv
The value of vRtrLdpStatsSvcFECRecv
specifies the number of Service FECs
received by the LDP instance from its
neighbors.
serviceFECsSent
long
vRtrLdpStatsSvcFECSent
The value of vRtrLdpStatsSvcFECSent
specifies the number of Service FECs sent
by the LDP instance to its neighbors.
sessionRejectedAdvertisementMod
eErrors
long
vRtrLdpStatsSessRejAdvE
rrors
The value of
vRtrLdpStatsSessRejAdvErrors gives the
total number of Session
Rejected/Parameters Advertisement
Mode Error Notification Messages sent or
received by this LDP instance.
sessionRejectedLabelRangeErrors
long
vRtrLdpStatsSessRejLabel
RangeErrors
The value of
vRtrLdpStatsSessRejLabelRangeErrors
gives the total number of Session
Rejected/Parameters Label Range Error
Notification Messages sent or received by
this LDP instance.
sessionRejectedMaxPduLengthErro
rs
long
vRtrLdpStatsSessRejMaxP
duErrors
The value of
vRtrLdpStatsSessRejMaxPduErrors gives
the total number of Session
Rejected/Parameters Max Pdu Length
Error Notification Messages sent or
received by this LDP instance.
sessionRejectedNoHelloErrors
long
vRtrLdpStatsSessRejNoHe
lloErrors
The value of
vRtrLdpStatsSessRejNoHelloErrors gives
the total number of Session Rejected/No
Hello Error Notification Messages sent or
received by this LDP instance.
shutdownNotificationsReceived
long
vRtrLdpStatsShutdownNo
tifRecv
The value of
vRtrLdpStatsShutdownNotifRecv gives the
number of Shutdown Notfications
received related to sessions associated
with this LDP instance.
shutdownNotificationsSent
long
vRtrLdpStatsShutdownNo
tifSent
The value of
vRtrLdpStatsShutdownNotifSent gives the
number of Shutdown Notfications sent
related to sessions associated with this
LDP instance.
TargetedPeerStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpIfStatsTable
Monitored class: ldp.TargetedPeer
existingAdjacencies
long
vRtrLdpIfExistingAdjacen
cies
The value of vRtrLdpIfExistingAdjacencies
gives a count of the total active
adjacencies on this LDP interface or with
this targeted peer.
(5 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-35
B. 7210 SAS-M Release 1.0 statistics counters
Table B-9 mpls statistics
5620 SAM counter name
Type
MIB counter name
Description
DynamicLspStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspStatTable
Monitored class: mpls.DynamicLsp
configuredPaths
long
vRtrMplsLspConfiguredPa
ths
The number of paths configured for this
LSP.
operationalPaths
long
vRtrMplsLspOperationalP
aths
The number of operational paths for this
LSP. This includes the path currently
active, as well as operational standby
paths.
pathChanges
long
vRtrMplsLspPathChanges
The number of path changes this LSP has
had. For every path change (path down,
path up, path change), a corresponding
syslog/trap (if enabled) is generated for
it.
standbyPaths
long
vRtrMplsLspStandbyPaths
The number of standby paths configured
for this LSP.
timeSinceLastPathChange
long
vRtrMplsLspLastPathChan
ge
The time in 10-millisecond units since the
last change occurred on this LSP.
timeSinceLastPrimaryUpState
long
vRtrMplsLspPrimaryTime
Up
The total time in 10-millisecond units that
this LSP's primary path has been
operational. For example, the percentage
contribution of the primary path to the
operational time is given by
(mplsLspPrimaryTimeUp/mplsLspTimeUp
* 100) .
LspPathStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspPathStatTable
Monitored class: mpls.LspPath
cspfQueries
long
vRtrMplsLspPathCspfQuer
ies
The value of vRtrMplsLspPathCspfQueries
specifies the number of CSPF queries that
have been made for this LSP path.
retryAttempts
long
vRtrMplsLspPathRetryAtt
empts
The number of unsuccessful attempts
which have been made to signal this path.
As soon as the path gets signalled, this is
set to 0.
timeDown
long
vRtrMplsLspPathTimeDow
n
The total time in 10-millisecond units that
this LSP Path has not been operational.
timeUp
long
vRtrMplsLspPathTimeUp
The total time in 10-millisecond units that
this LSP path has been operational. For
example, the percentage up time can be
determined by computing
(mplsLspPathTimeUp/mplsLspAge * 100 ).
transitionCount
long
vRtrMplsLspPathTransitio
nCount
The object
vRtrMplsLspPathTransitionCount
maintains the number of transitions that
have occurred for this LSP.
(1 of 3)
B-36
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
LspStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspStatTable
Monitored classes:
•
•
•
mpls.DynamicLsp
mpls.StaticLsp
mpls.BypassOnlyLsp
age
long
vRtrMplsLspAge
The age (i.e., time from creation till now)
of this LSP in 10-millisecond periods.
timeSinceLastDownState
long
vRtrMplsLspTimeDown
The total time in 10-millisecond units that
this LSP has not been operational.
timeSinceLastTransition
long
vRtrMplsLspLastTransitio
n
The time in 10-millisecond units since the
last transition occurred on this LSP.
timeSinceLastUpState
long
vRtrMplsLspTimeUp
The total time in 10-millisecond units that
this LSP has been been operational. For
example, the percentage up time can be
determined by computing
(mplsLspTimeUp/mplsLspAge * 100 ).
transitions
long
vRtrMplsLspTransitions
The number of state transitions (up ->
down and down -> up) this LSP has
undergone.
MplsInterfaceStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsIfStatTable
Monitored class: mpls.Interface
receiveOctets
UINT128
vRtrMplsIfRxOctetCount
The total number of bytes in MPLS labeled
packets received on this interface.
receivePackets
UINT128
vRtrMplsIfRxPktCount
The total number of MPLS labeled packets
received on this interface.
transmitOctets
UINT128
vRtrMplsIfTxOctetCount
The total number of bytes in MPLS labeled
packets transmitted on this interface.
transmitPackets
UINT128
vRtrMplsIfTxPktCount
The total number of MPLS labeled packets
transmitted from this interface.
SiteStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsGeneralStatTable
Monitored class: mpls.Site
detourOriginate
long
vRtrMplsGeneralDetourLs
pOriginate
This object counts the number of detour
LSPs that originate at this virtual router.
detourTerminate
long
vRtrMplsGeneralDetourLs
pTerminate
This object counts the number of detour
LSPs that terminate at this virtual router.
detourTransit
long
vRtrMplsGeneralDetourLs
pTransit
This object counts the number of detour
LSPs that transit through this virtual
router.
dynamicOriginate
long
vRtrMplsGeneralDynamic
LspOriginate
This object counts the number of dynamic
LSPs that originate at this virtual router.
dynamicTerminate
long
vRtrMplsGeneralDynamic
LspTerminate
This object counts the number of dynamic
LSPs that terminate at this virtual router.
dynamicTransit
long
vRtrMplsGeneralDynamic
LspTransit
This object counts the number of dynamic
LSPs that transit through this virtual
router.
(2 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-37
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
staticOriginate
long
vRtrMplsGeneralStaticLsp
Originate
This object counts the number of static
LSPs that originate at this virtual router.
staticTerminate
long
vRtrMplsGeneralStaticLsp
Terminate
This object counts the number of static
LSPs that terminate at this virtual router.
staticTransit
long
vRtrMplsGeneralStaticLsp
Transit
This object counts the number of static
LSPs that transit through this virtual
router.
(3 of 3)
Table B-10 ospf statistics
5620 SAM counter name
Type
MIB counter name
Description
AreaBasicStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfAreaTable
Monitored class: ospf.AreaSite
nssaTranslatorEvents
long
tmnxOspfAreaNssaTransl
atorEvents
The value of
tmnxOspfAreaNssaTranslatorEvents
indicates the number of Translator State
changes that have occurred since the last
boot-up.
totalLSACount
long
tmnxOspfAreaScopeLsaCo
unt
The value of tmnxOspfAreaScopeLsaCount
indicates the total number of Area-Scope
link state advertisements in this area's
link-state database.
totalSpfRuns
long
tmnxOspfAreaSpfRuns
The value of tmnxOspfAreaSpfRuns
indicates the number of times that the
intra-area route table has been
calculated using this area's link-state
database. This is typically done using
Dijkstra's algorithm.
totalUnknownLSACount
long
tmnxOspfAreaScopeUnkLs
aCount
The value of
tmnxOspfAreaScopeUnkLsaCount
indicates the total number of unknown
Area-Scope link-state advertisements in
this area's link-state database.
InterfaceGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
events
long
tmnxOspfIfEvents
The value of tmnxOspfIfEvents indicates
the number of times this OSPF interface
has changed its state, or an error has
occurred.
InterfaceReceiveStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
databaseDescriptionPackets
long
tmnxOspfIfRxDBDs
The value of tmnxOspfIfRxDBDs indicates
the total number of OSPF DataBase
Description packets received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
(1 of 12)
B-38
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
databaseDescriptionPackets
long
tmnxOspfIfTxDBDs
The value of tmnxOspfIfTxDBDs indicates
the total number of OSPF DataBase
Description packets transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
helloPackets
long
tmnxOspfIfRxHellos
The value of tmnxOspfIfRxHellos indicates
the total number of OSPF Hello packets
received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
helloPackets
long
tmnxOspfIfTxHellos
The value of tmnxOspfIfTxHellos indicates
the total number of OSPF Hello packets
transmitted on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfRxLSAcks
The value of tmnxOspfIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfTxLSAcks
The value of tmnxOspfIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this interface since tmnxOspfAdminState
was last set to 'enabled'.
linkStateRequests
long
tmnxOspfIfRxLSRs
The value of tmnxOspfIfRxLSRs indicates
the total number of Link State Requests
(LSRs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateRequests
long
tmnxOspfIfTxLSRs
The value of tmnxOspfIfTxLSRs indicates
the total number of OSPF Link State
Requests (LSRs)transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateUpdates
long
tmnxOspfIfRxLSUs
The value of tmnxOspfIfRxLSUs indicates
the total number of Link State Updates
(LSUs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateUpdates
long
tmnxOspfIfTxLSUs
The value of tmnxOspfIfTxLSUs indicates
the total number of OSPF Link State
Updates (LSUs) transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
lsasWithBadChecksums
long
tmnxOspfIfRxBadChecksu
ms
The value of tmnxOspfIfRxBadChecksums
indicates the count of LSAs received with
bad checksums.
totalPackets
long
tmnxOspfIfRxPackets
The value of tmnxOspfIfRxPackets
indicates the total number of OSPF
packets received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
(2 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-39
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalPackets
long
tmnxOspfIfTxPackets
The value of tmnxOspfIfTxPackets
indicates the total number of OSPF
packets transmitted on this interface
since tmnxOspfAdminState was last set to
'enabled'.
InterfaceStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
authorizationFailures
long
tmnxOspfIfAuthFailures
The value of tmnxOspfIfAuthFailures
indicates the total number of OSPF
packets received with an invalid
authorization key since
tmnxOspfAdminState was last set to
'enabled'.
badAreas
long
tmnxOspfIfBadAreas
The value of tmnxOspfIfBadAreas
indicates the total number of OSPF
packets received with an area mismatch
since tmnxOspfAdminState was last set to
'enabled'.
badAuthorizationTypes
long
tmnxOspfIfBadAuthTypes
The value of tmnxOspfIfBadAuthTypes
indicates the total number of OSPF
packets received with an invalid
authorization type since
tmnxOspfAdminState was last set to
'enabled'.
badDeadIntervals
long
tmnxOspfIfBadDeadInterv
als
The value of tmnxOspfIfBadDeadIntervals
indicates the total number of OSPF
packets received where the dead interval
given in the packet was not equal to that
configured on this interface since
tmnxOspfAdminState was last set to
'enabled'.
badDestinationAddresses
long
tmnxOspfIfBadDstAddrs
The value of tmnxOspfIfBadDstAddrs
indicates the total number of OSPF
packets received with the incorrect IP
destination address since
tmnxOspfAdminState was last set to
'enabled'.
badHelloIntervals
long
tmnxOspfIfBadHelloInterv
als
The value of tmnxOspfIfBadHelloIntervals
indicates the total number of OSPF
packets received where the hello interval
given in packet was not equal to that
configured on this interface since
tmnxOspfAdminState was last set to
'enabled'.
badLengths
long
tmnxOspfIfBadLengths
The value of tmnxOspfIfBadLengths
indicates the total number of OSPF
packets received on this interface with a
total length not equal to the length given
in the packet itself since
tmnxOspfAdminState was last set to
'enabled'.
(3 of 12)
B-40
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badNeighbors
long
tmnxOspfIfBadNeighbors
The value of tmnxOspfIfBadNeighbors
indicates the total number of OSPF
packets received where the neighbor
information does not match the
information this router has for the
neighbor since tmnxOspfAdminState was
last set to 'enabled'.
badNetworks
long
tmnxOspfIfBadNetworks
The value of tmnxOspfIfBadNetworks
indicates the total number of OSPF
packets received with invalid network or
mask since tmnxOspfAdminState was last
set to 'enabled'.
badOptions
long
tmnxOspfIfBadOptions
The value of tmnxOspfIfBadOptions
indicates the total number of OSPF
packets received with an option that does
not match those configured for this
interface or area since
tmnxOspfAdminState was last set to
'enabled'.
badPacketTypes
long
tmnxOspfIfBadPacketTyp
es
The value of tmnxOspfIfBadPacketTypes
indicates the total number of OSPF
packets received with an invalid OSPF
packet type since tmnxOspfAdminState
was last set to 'enabled'.
badVersions
long
tmnxOspfIfBadVersions
The value of tmnxOspfIfBadVersions
indicates the total number of OSPF
packets received with bad OSPF version
numbers since tmnxOspfAdminState was
last set to 'enabled'.
badVirtualLinks
long
tmnxOspfIfBadVirtualLink
s
The value of tmnxOspfIfBadVirtualLinks
indicates the total number of OSPF
packets received on this interface that
are destined to a virtual link that does not
exist since tmnxOspfAdminState was last
set to 'enabled'.
discardPackets
long
tmnxOspfIfDiscardPacket
s
The value of tmnxOspfIfDiscardPackets
indicates the total number of OSPF
packets discarded on this interface since
tmnxOspfAdminState was last set to
'enabled'.
retransmitOuts
long
tmnxOspfIfRetransmitOut
s
The value of tmnxOspfIfRetransmitOuts
indicates the total number of OSPF
Retransmits sent on this interface since
tmnxOspfAdminState was last set to
'enabled'.
InterfaceTransmitStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
databaseDescriptionPackets
long
tmnxOspfIfRxDBDs
The value of tmnxOspfIfRxDBDs indicates
the total number of OSPF DataBase
Description packets received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
(4 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-41
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
databaseDescriptionPackets
long
tmnxOspfIfTxDBDs
The value of tmnxOspfIfTxDBDs indicates
the total number of OSPF DataBase
Description packets transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
helloPackets
long
tmnxOspfIfRxHellos
The value of tmnxOspfIfRxHellos indicates
the total number of OSPF Hello packets
received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
helloPackets
long
tmnxOspfIfTxHellos
The value of tmnxOspfIfTxHellos indicates
the total number of OSPF Hello packets
transmitted on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfRxLSAcks
The value of tmnxOspfIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfTxLSAcks
The value of tmnxOspfIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this interface since tmnxOspfAdminState
was last set to 'enabled'.
linkStateRequests
long
tmnxOspfIfRxLSRs
The value of tmnxOspfIfRxLSRs indicates
the total number of Link State Requests
(LSRs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateRequests
long
tmnxOspfIfTxLSRs
The value of tmnxOspfIfTxLSRs indicates
the total number of OSPF Link State
Requests (LSRs)transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateUpdates
long
tmnxOspfIfRxLSUs
The value of tmnxOspfIfRxLSUs indicates
the total number of Link State Updates
(LSUs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateUpdates
long
tmnxOspfIfTxLSUs
The value of tmnxOspfIfTxLSUs indicates
the total number of OSPF Link State
Updates (LSUs) transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
totalPackets
long
tmnxOspfIfRxPackets
The value of tmnxOspfIfRxPackets
indicates the total number of OSPF
packets received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
totalPackets
long
tmnxOspfIfTxPackets
The value of tmnxOspfIfTxPackets
indicates the total number of OSPF
packets transmitted on this interface
since tmnxOspfAdminState was last set to
'enabled'.
(5 of 12)
B-42
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
NeighborGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfNbrStatsTable
Monitored class: ospf.Neighbor
events
long
tmnxOspfNbrEvents
The value of tmnxOspfNbrEvents
indicates the number of times this
neighbor relationship has changed state,
or an error has occurred.
retransmissionQueueLength
long
tmnxOspfNbrLsRetransQL
en
The value of tmnxOspfNbrLsRetransQLen
indicates the current length of the
retransmission queue.
NeighborStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfNbrStatsTable
Monitored class: ospf.Neighbor
badMtus
long
tmnxOspfNbrBadMTUs
The value of tmnxOspfNbrBadMTUs
indicates the total number of times when
the MTU in a received database
description packet was larger than the
MTU of the receiving interface since
tmnxOspfAdminState was last set to
'enabled'.
badNeighborStates
long
tmnxOspfNbrBadNbrState
s
The value of tmnxOspfNbrBadNbrStates
indicates the total number of OSPF
packets received when the neighbor state
was not expecting to receive this packet
type since tmnxOspfAdminState was last
set to 'enabled'.
badPackets
long
tmnxOspfNbrBadPackets
The value of tmnxOspfNbrBadPackets
indicates the total number of times when
an LS update was received with an illegal
LS type or an option mismatch since
tmnxOspfAdminState was last set to
'enabled'.
badSequenceNumbers
long
tmnxOspfNbrBadSeqNums
The value of tmnxOspfNbrBadSeqNums
indicates the total number of times when
a database description packet was
received with a sequence number
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
duplicates
long
tmnxOspfNbrDuplicates
The value of tmnxOspfNbrDuplicates
indicates the total number of times when
a duplicate database description packet
was received during the Exchange state
since tmnxOspfAdminState was last set to
'enabled'.
lsaInstallFailed
long
tmnxOspfNbrLsaInstallFai
led
The value of tmnxOspfNbrLsaInstallFailed
indicates the total number of times an
LSA could not be installed into the LSDB
due to a resource allocation issue since
tmnxOspfAdminState was last set to
'enabled'.
lsaNotInLSDB
long
tmnxOspfNbrLsaNotInLsd
bs
The value of tmnxOspfNbrLsaNotInLsdbs
indicates the total number of times when
an LS request was received for an LSA not
installed in the LSDB of this router since
tmnxOspfAdminState was last set to
'enabled'.
(6 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-43
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
numberOfRestarts
long
tmnxOspfNbrNumRestarts
The value of tmnxOspfNbrNumRestarts
indicates the number of times the
neighbor has attempted restart.
optionMismatches
long
tmnxOspfNbrOptionMism
atches
The value of
tmnxOspfNbrOptionMismatches indicates
the total number of times when a LS
update was received with an option
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
SiteStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfStatisticsTable
Monitored class: ospf.Site
addRouteFailed
long
tmnxOspfRoutesAddsFail
ed
The value of tmnxOspfRoutesAddsFailed
indicates the number of times an attempt
to add a route to the Route Table Manager
(RTM) failed for this OSPF instance.
cspfDroppedRequests
long
tmnxOspfCSPFDroppedRe
quests
The value of
tmnxOspfCSPFDroppedRequests indicates
the number of dropped CSPF requests
made by the OSPF protocol.
cspfPathsFound
long
tmnxOspfCSPFPathsFoun
d
The value of tmnxOspfCSPFPathsFound
indicates the number of of paths found for
the requests made to OSPF protocol.
cspfPathsNotFound
long
tmnxOspfCSPFPathsNotFo
und
The value of
tmnxOspfCSPFPathsNotFound indicates
the number of of paths not found for the
requests made to OSPF protocol.
cspfRequests
long
tmnxOspfCSPFRequests
The value of tmnxOspfCSPFRequests
indicates the number of CSPF requests
made to the OSPF protocol.
deleteRouteFailed
long
tmnxOspfRoutesDelsFaile
d
The value of tmnxOspfRoutesDelsFailed
indicates the number of times an attempt
to delete a route from the Route Table
Manager (RTM) failed for this instance of
OSPF.
inOverflowCount
long
tmnxOspfNumTimesInOve
rflow
The value of
tmnxOspfNumTimesInOverflow indicates
the count of the number of times the
system was in the overflow state.
inOverloadCount
long
tmnxOspfNumTimesInOve
rload
The value of
tmnxOspfNumTimesInOverload indicates
the count of the number of times the
system was overloaded.
modifyRouteFailed
long
tmnxOspfRoutesModsFail
ed
The value of tmnxOspfRoutesModsFailed
indicates the number of times an attempt
to modify a route in the Route Table
Manager (RTM) failed for this instance of
OSPF.
newLsasOriginated
long
tmnxOspfOriginateNewLs
as
The value of tmnxOspfOriginateNewLsas
indicates the number of new link-state
advertisements that have been
originated. This number is incremented
each time the router originates a new
LSA.
(7 of 12)
B-44
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
newLsasReceived
long
tmnxOspfRxNewLsas
The value of tmnxOspfRxNewLsas
indicates the number of link-state
advertisements received determined to
be new instantiations. This number does
not include newer instantiations of
self-originated link-state advertisements.
spfAttemptsFailed
long
tmnxOspfSpfAttemptsFail
ed
The value of tmnxOspfSpfAttemptsFailed
indicates the number of times an attempt
to run SPF has failed because SPF runs
have been stopped as a result of
insufficient memory resources.
VirtualLinkGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
events
long
tmnxOspfVirtIfEvents
The value of tmnxOspfVirtIfEvents
indicates the number of state changes or
error events on this Virtual Link.
VirtualLinkReceiveStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
databaseDescriptionPackets
long
tmnxOspfVirtIfRxDBDs
The value of tmnxOspfVirtIfRxDBDs
indicates the total number of OSPF
DataBase Description packets received on
this virtual interface.
databaseDescriptionPackets
long
tmnxOspfVirtIfTxDBDs
The value of tmnxOspfVirtIfTxDBDs
indicates the total number of OSPF
DataBase Description packets transmitted
on this virtual interface.
helloPackets
long
tmnxOspfVirtIfRxHellos
The value of tmnxOspfVirtIfRxHellos
indicates the total number of OSPF Hello
packets received on this virtual interface.
helloPackets
long
tmnxOspfVirtIfTxHellos
The value of tmnxOspfVirtIfTxHellos
indicates the total number of OSPF Hello
packets transmitted on this virtual
interface since it was created.
linkStateAcknowledgements
long
tmnxOspfVirtIfRxLSAcks
The value of tmnxOspfVirtIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
virtual interface.
linkStateAcknowledgements
long
tmnxOspfVirtIfTxLSAcks
The value of tmnxOspfVirtIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this virtual interface.
linkStateRequests
long
tmnxOspfVirtIfRxLSRs
The value of tmnxOspfVirtIfRxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) received on this
virtual interface.
linkStateRequests
long
tmnxOspfVirtIfTxLSRs
The value of tmnxOspfVirtIfTxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) transmitted on this
virtual interface.
(8 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-45
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
linkStateUpdates
long
tmnxOspfVirtIfRxLSUs
The value of tmnxOspfVirtIfRxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) received on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfTxLSUs
The value of tmnxOspfVirtIfTxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) transmitted on this
virtual interface.
lsasWithBadChecksums
long
tmnxOspfVirtIfRxBadChec
ksums
The value of
tmnxOspfVirtIfRxBadChecksums indicates
the count of LSAs received with bad
checksums.
totalPackets
long
tmnxOspfVirtIfRxPackets
The value of tmnxOspfVirtIfRxPackets
indicates the total number of OSPF
packets received on this virtual interface
since it was created.
totalPackets
long
tmnxOspfVirtIfTxPackets
The value of tmnxOspfVirtIfTxPackets
indicates the total number of OSPF
packets transmitted on this virtual
interface since it was created.
VirtualLinkStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
authorizationFailures
long
tmnxOspfVirtIfAuthFailur
es
The value of tmnxOspfVirtIfAuthFailures
indicates the total number of OSPF
packets received on this virtual interface
with invalid authentication keys.
badAreas
long
tmnxOspfVirtIfBadAreas
The value of tmnxOspfVirtIfBadAreas
indicates the total number of OSPF
packets received on this virtual interface
with area mismatches.
badAuthorizationTypes
long
tmnxOspfVirtIfBadAuthTy
pes
The value of tmnxOspfVirtIfBadAuthTypes
indicates the total number of OSPF
packets received on this virtual interface
with invalid authentication types.
badDeadIntervals
long
tmnxOspfVirtIfBadDeadIn
tervals
The value of
tmnxOspfVirtIfBadDeadIntervals indicates
the total number of OSPF packets
received where the dead interval given in
the packet was not equal to that
configured on this virtual interface since
tmnxOspfAdminState was last set to
'enabled'.
badDestinationAddresses
long
tmnxOspfVirtIfBadDstAdd
rs
The value of tmnxOspfVirtIfBadDstAddrs
indicates the total number of OSPF
packets received on this virtual interface
with invalid destination IP address.
badHelloIntervals
long
tmnxOspfVirtIfBadHelloIn
tervls
The value of
tmnxOspfVirtIfBadHelloIntervls indicates
the total number of OSPF packets
received where the hello interval given in
packet was not equal to that configured
on this virtual interface since
tmnxOspfAdminState was last set to
'enabled'.
(9 of 12)
B-46
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badLengths
long
tmnxOspfVirtIfBadLength
s
The value of tmnxOspfVirtIfBadLengths
indicates the total number of OSPF
packets received on this virtual interface
with a total length not equal to the length
given in the packet itself since
tmnxOspfAdminState was last set to
'enabled'.
badNeighbors
long
tmnxOspfVirtIfBadNeighb
ors
The value of
tmnxOspfVirtIfBadNeighborsthe indicates
the total number of OSPF packets
received where the neighbor information
does not match the configuration this
router has for the neighbor.
badNetworks
long
tmnxOspfVirtIfBadNetwor
ks
The value of tmnxOspfVirtIfBadNetworks
indicates the total number of OSPF
packets received on this virtual interface
with invalid network or mask fields.
badOptions
long
tmnxOspfVirtIfBadOption
s
The value of tmnxOspfVirtIfBadOptions
indicates the total number of OSPF
packets received with an option that does
not match those configured for this
virtual interface or transit-area since
tmnxOspfAdminState was last set to
'enabled'.
badPacketTypes
long
tmnxOspfVirtIfBadPacket
Types
The value of
tmnxOspfVirtIfBadPacketTypes indicates
the total number of OSPF packets
received on this virtual interface with
invalid OSPF packet types.
badVersions
long
tmnxOspfVirtIfBadVersion
s
The value oftmnxOspfVirtIfBadVersions
indicates the total number of OSPF
packets received on this virtual interface
with invalid OSPF version numbers.
discardPackets
long
tmnxOspfVirtIfDiscardPac
kets
The value of
tmnxOspfVirtIfDiscardPackets indicates
the total number of OSPF packets
discarded on this virtual interface.
retransmitOuts
long
tmnxOspfVirtIfRetransmit
Outs
The value of
tmnxOspfVirtIfRetransmitOuts indicates
the total number of OSPF packets
retransmitted on this virtual interface.
VirtualLinkTransmitStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
databaseDescriptionPackets
long
tmnxOspfVirtIfRxDBDs
The value of tmnxOspfVirtIfRxDBDs
indicates the total number of OSPF
DataBase Description packets received on
this virtual interface.
databaseDescriptionPackets
long
tmnxOspfVirtIfTxDBDs
The value of tmnxOspfVirtIfTxDBDs
indicates the total number of OSPF
DataBase Description packets transmitted
on this virtual interface.
helloPackets
long
tmnxOspfVirtIfRxHellos
The value of tmnxOspfVirtIfRxHellos
indicates the total number of OSPF Hello
packets received on this virtual interface.
(10 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-47
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
helloPackets
long
tmnxOspfVirtIfTxHellos
The value of tmnxOspfVirtIfTxHellos
indicates the total number of OSPF Hello
packets transmitted on this virtual
interface since it was created.
linkStateAcknowledgements
long
tmnxOspfVirtIfRxLSAcks
The value of tmnxOspfVirtIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
virtual interface.
linkStateAcknowledgements
long
tmnxOspfVirtIfTxLSAcks
The value of tmnxOspfVirtIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this virtual interface.
linkStateRequests
long
tmnxOspfVirtIfRxLSRs
The value of tmnxOspfVirtIfRxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) received on this
virtual interface.
linkStateRequests
long
tmnxOspfVirtIfTxLSRs
The value of tmnxOspfVirtIfTxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) transmitted on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfRxLSUs
The value of tmnxOspfVirtIfRxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) received on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfTxLSUs
The value of tmnxOspfVirtIfTxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) transmitted on this
virtual interface.
totalPackets
long
tmnxOspfVirtIfRxPackets
The value of tmnxOspfVirtIfRxPackets
indicates the total number of OSPF
packets received on this virtual interface
since it was created.
totalPackets
long
tmnxOspfVirtIfTxPackets
The value of tmnxOspfVirtIfTxPackets
indicates the total number of OSPF
packets transmitted on this virtual
interface since it was created.
VirtualNeighborGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtNbrStatsTable
Monitored class: ospf.VirtualNeighbor
events
long
tmnxOspfVirtNbrEvents
The value of tmnxOspfVirtNbrEvents
indicates the number of times this virtual
link has changed its state, or an error has
occurred.
retransmissionQueueLength
long
tmnxOspfVirtNbrLsRetran
sQLen
The value of
tmnxOspfVirtNbrLsRetransQLen indicates
the current length of the retransmission
queue.
VirtualNeighborStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtNbrStatsTable
Monitored class: ospf.VirtualNeighbor
(11 of 12)
B-48
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badMtus
long
tmnxOspfVirtNbrBadMTUs
The value of tmnxOspfVirtNbrBadMTUs
indicates the total number of times when
the MTU in a received database
description packet was larger than the
MTU of the receiving interface since
tmnxOspfAdminState was last set to
'enabled'.
badPackets
long
tmnxOspfVirtNbrBadPack
ets
The value of tmnxOspfVirtNbrBadPackets
indicates the total number of times when
an LS update was received with an illegal
LS type or an option mismatch since
tmnxOspfAdminState was last set to
'enabled'.
badSequenceNumbers
long
tmnxOspfVirtNbrBadSeqN
ums
The value of
tmnxOspfVirtNbrBadSeqNums indicates
the total number of times when a
database description packet was received
with a sequence number mismatch since
tmnxOspfAdminState was last set to
'enabled'.
badVirtualNeighborStates
long
tmnxOspfVirtNbrBadNbrS
tates
The value of
tmnxOspfVirtNbrBadNbrStates indicates
the total number of OSPF packets
received when the virtual neighbor state
was not expecting to receive this packet
type since tmnxOspfAdminStat was last
set to 'enabled'.
duplicates
long
tmnxOspfVirtNbrDuplicat
es
The value of tmnxOspfVirtNbrDuplicates
indicates the total number of times when
a duplicate database description packet
was received during the Exchange state
since tmnxOspfAdminState was last set to
'enabled'.
lsaInstallFailed
long
tmnxOspfVirtNbrLsaInstal
lFail
The value of
tmnxOspfVirtNbrLsaInstallFail indicates
the total number of times when an LSA
could not be installed into the LSDB due to
a resource allocation issue since
tmnxOspfAdminState was last set to
'enabled'.
lsaNotInLSDB
long
tmnxOspfVirtNbrLsaNotIn
Lsdbs
The value of
tmnxOspfVirtNbrLsaNotInLsdbs indicates
the total number of times when an LS
request was received for an LSA not
installed in the LSDB of this router since
tmnxOspfAdminState was last set to
'enabled'.
numberOfRestarts
long
tmnxOspfVirtNbrNumRest
arts
The value of
tmnxOspfVirtNbrNumRestarts indicates
the number of times the virtual neighbor
has attempted restart since
tmnxOspfAdminState was last set to
'enabled'.
optionMismatches
long
tmnxOspfVirtNbrOptionMi
smatch
The value of
tmnxOspfVirtNbrOptionMismatch
indicates the total number of times when
a LS update was received with an option
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
(12 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-49
B. 7210 SAS-M Release 1.0 statistics counters
Table B-11 pae802_1x statistics
5620 SAM counter name
Type
MIB counter name
Description
PaePortAuthenticatorDiagStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthDiagTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dot1xAuthAuthEapLogoffWhileAut
henticated
long
dot1xAuthAuthEapLogoff
WhileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to DISCONNECTED, as a
result of an EAPOL-Logoff message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.12.
dot1xAuthAuthEapLogoffWhileAut
henticating
long
dot1xAuthAuthEapLogoff
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of an EAPOL-Logoff message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.9.
dot1xAuthAuthEapStartsWhileAuth
enticated
long
dot1xAuthAuthEapStarts
WhileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to CONNECTING, as a
result of an EAPOL-Start message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.11.
dot1xAuthAuthEapStartsWhileAuth
enticating
long
dot1xAuthAuthEapStarts
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of an EAPOL-Start message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.8.
dot1xAuthAuthFailWhileAuthentic
ating
long
dot1xAuthAuthFailWhileA
uthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to HELD, as a result of
the Backend Authentication state
machine indicating authentication failure
(authFail = TRUE). REFERENCE 9.4.2,
8.5.4.2.6.
dot1xAuthAuthReauthsWhileAuthe
nticated
long
dot1xAuthAuthReauthsW
hileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to CONNECTING, as a
result of a reauthentication request
(reAuthenticate = TRUE). REFERENCE
9.4.2, 8.5.4.2.10.
dot1xAuthAuthReauthsWhileAuthe
nticating
long
dot1xAuthAuthReauthsW
hileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of a reauthentication request
(reAuthenticate = TRUE). REFERENCE
9.4.2, 8.5.4.2.7.
(1 of 4)
B-50
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthAuthSuccessWhileAuthe
nticating
long
dot1xAuthAuthSuccessWh
ileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to AUTHENTICATED, as
a result of the Backend Authentication
state machine indicating successful
authentication of the Supplicant
(authSuccess = TRUE). REFERENCE 9.4.2,
8.5.4.2.4.
dot1xAuthAuthTimeoutsWhileAuth
enticating
long
dot1xAuthAuthTimeouts
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of the Backend Authentication
state machine indicating authentication
timeout (authTimeout = TRUE).
REFERENCE 9.4.2, 8.5.4.2.5.
dot1xAuthBackendAccessChalleng
es
long
dot1xAuthBackendAccess
Challenges
Counts the number of times that the state
machine receives an initial
Access-Challenge packet from the
Authentication server (i.e., aReq
becomes TRUE, causing exit from the
RESPONSE state). Indicates that the
Authentication Server has communication
with the Authenticator. REFERENCE 9.4.2,
8.5.6.2.2.
dot1xAuthBackendAuthFails
long
dot1xAuthBackendAuthFa
ils
Counts the number of times that the state
machine receives an EAP-Failure message
from the Authentication Server (i.e., aFail
becomes TRUE, causing a transition from
RESPONSE to FAIL). Indicates that the
Supplicant has not authenticated to the
Authentication Server. REFERENCE 9.4.2,
8.5.6.2.6.
dot1xAuthBackendAuthSuccesses
long
dot1xAuthBackendAuthSu
ccesses
Counts the number of times that the state
machine receives an EAP-Success message
from the Authentication Server (i.e.,
aSuccess becomes TRUE, causing a
transition from RESPONSE to SUCCESS).
Indicates that the Supplicant has
successfully authenticated to the
Authentication Server. REFERENCE 9.4.2,
8.5.6.2.5.
dot1xAuthBackendNonNakRespons
esFromSupplicant
long
dot1xAuthBackendNonNa
kResponsesFromSupplica
nt
Counts the number of times that the state
machine receives a response from the
Supplicant to an initial EAP-Request, and
the response is something other than
EAP-NAK (i.e., rxResp becomes TRUE,
causing the state machine to transition
from REQUEST to RESPONSE, and the
response is not an EAP-NAK). Indicates
that the Supplicant can respond to the
Authenticator's chosen EAP-method.
REFERENCE 9.4.2, 8.5.6.2.4.
dot1xAuthBackendOtherRequestsT
oSupplicant
long
dot1xAuthBackendOtherR
equestsToSupplicant
Counts the number of times that the state
machine sends an EAP-Request packet
(other than an Identity, Notification,
Failure or Success message) to the
Supplicant (i.e., executes txReq on entry
to the REQUEST state). Indicates that the
Authenticator chose an EAP-method.
REFERENCE 9.4.2, 8.5.6.2.3.
(2 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-51
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthBackendResponses
long
dot1xAuthBackendRespon
ses
Counts the number of times that the state
machine sends an initial Access-Request
packet to the Authentication server (i.e.,
executes sendRespToServer on entry to
the RESPONSE state). Indicates that the
Authenticator attempted communication
with the Authentication Server.
REFERENCE 9.4.2, 8.5.6.2.1.
dot1xAuthEapLogoffsWhileConnec
ting
long
dot1xAuthEapLogoffsWhil
eConnecting
Counts the number of times that the state
machine transitions from CONNECTING to
DISCONNECTED as a result of receiving an
EAPOL-Logoff message. REFERENCE 9.4.2,
8.5.4.2.2.
dot1xAuthEntersAuthenticating
long
dot1xAuthEntersAuthenti
cating
Counts the number of times that the state
machine transitions from CONNECTING to
AUTHENTICATING, as a result of an
EAP-Response/Identity message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.3.
dot1xAuthEntersConnecting
long
dot1xAuthEntersConnecti
ng
Counts the number of times that the state
machine transitions to the CONNECTING
state from any other state. REFERENCE
9.4.2, 8.5.4.2.1.
PaePortAuthenticatorSessionStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthSessionStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
dot1xAuthSessionAuthenticMethod
int
dot1xAuthSessionAuthent
icMethod
The authentication method used to
establish the session. REFERENCE 9.4.4,
Session Authentication Method.
dot1xAuthSessionFramesRx
long
dot1xAuthSessionFrames
Rx
The number of user data frames received
on this Port during the session.
REFERENCE 9.4.4, Session Frames
Received.
dot1xAuthSessionFramesTx
long
dot1xAuthSessionFrames
Tx
The number of user data frames
transmitted on this Port during the
session. REFERENCE 9.4.4, Session Frames
Transmitted.
dot1xAuthSessionOctetsRx
UINT128
dot1xAuthSessionOctetsR
x
The number of octets received in user
data frames on this Port during the
session. REFERENCE 9.4.4, Session Octets
Received.
dot1xAuthSessionOctetsTx
UINT128
dot1xAuthSessionOctetsT
x
The number of octets transmitted in user
data frames on this Port during the
session. REFERENCE 9.4.4, Session Octets
Transmitted.
dot1xAuthSessionTerminateCause
int
dot1xAuthSessionTermina
teCause
The reason for the session termination.
REFERENCE 9.4.4, Session Terminate
Cause.
dot1xAuthSessionTime
long
dot1xAuthSessionTime
The duration of the session in seconds.
REFERENCE 9.4.4, Session Time.
(3 of 4)
B-52
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
PaePortAuthenticatorStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthStatsTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dot1xAuthEapLengthErrorFramesR
x
long
dot1xAuthEapLengthError
FramesRx
The number of EAPOL frames that have
been received by this Authenticator in
which the Packet Body Length field is
invalid. REFERENCE 9.4.2, EAP length
error frames received.
dot1xAuthEapolFramesRx
long
dot1xAuthEapolFramesRx
The number of valid EAPOL frames of any
type that have been received by this
Authenticator. REFERENCE 9.4.2, EAPOL
frames received.
dot1xAuthEapolFramesTx
long
dot1xAuthEapolFramesTx
The number of EAPOL frames of any type
that have been transmitted by this
Authenticator. REFERENCE 9.4.2, EAPOL
frames transmitted.
dot1xAuthEapolLogoffFramesRx
long
dot1xAuthEapolLogoffFra
mesRx
The number of EAPOL Logoff frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Logoff frames
received.
dot1xAuthEapolReqFramesTx
long
dot1xAuthEapolReqFrame
sTx
The number of EAP Request frames (other
than Rq/Id frames) that have been
transmitted by this Authenticator.
REFERENCE 9.4.2, EAPOL Request frames
transmitted.
dot1xAuthEapolReqIdFramesTx
long
dot1xAuthEapolReqIdFra
mesTx
The number of EAP Req/Id frames that
have been transmitted by this
Authenticator. REFERENCE 9.4.2, EAPOL
Req/Id frames transmitted.
dot1xAuthEapolRespFramesRx
long
dot1xAuthEapolRespFram
esRx
The number of valid EAP Response frames
(other than Resp/Id frames) that have
been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Response
frames received.
dot1xAuthEapolRespIdFramesRx
long
dot1xAuthEapolRespIdFra
mesRx
The number of EAP Resp/Id frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Resp/Id frames
received.
dot1xAuthEapolStartFramesRx
long
dot1xAuthEapolStartFram
esRx
The number of EAPOL Start frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Start frames
received.
dot1xAuthInvalidEapolFramesRx
long
dot1xAuthInvalidEapolFra
mesRx
The number of EAPOL frames that have
been received by this Authenticator in
which the frame type is not recognized.
REFERENCE 9.4.2, Invalid EAPOL frames
received.
dot1xAuthLastEapolFrameVersion
long
dot1xAuthLastEapolFram
eVersion
The protocol version number carried in
the most recently received EAPOL frame.
REFERENCE 9.4.2, Last EAPOL frame
version.
(4 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-53
B. 7210 SAS-M Release 1.0 statistics counters
Table B-12 rsvp statistics
5620 SAM counter name
Type
MIB counter name
Description
AuthenticationKeyStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfStatTable
Monitored class: rsvp.AuthenticationKey
errorPacketsReceived
UINT128
vRtrRsvpIfStatRxAuthErro
rs
The total number of RSVP packets with
MD5 errors received on this RSVP
interface.
errorPacketsTransmitted
UINT128
vRtrRsvpIfStatTxAuthErro
rs
The total number of RSVP packets with
MD5 errors sent by this RSVP interface.
RsvpInterfaceReceiveStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfStatTable
Monitored class: rsvp.Interface
acks
UINT128
vRtrRsvpIfStatRxAcks
The total number of RSVP ACK messages
received when refresh reduction is
enabled on this RSVP interface.
acks
UINT128
vRtrRsvpIfStatTxAcks
The total number of RSVP ACK messages
that have been transmitted on this RSVP
interface when refresh reduction is
enabled.
bundles
UINT128
vRtrRsvpIfStatRxBundles
The total number of RSVP bundled
packets received on this RSVP interface.
Bundled packets are sent when refresh
reduction is enabled.
bundles
UINT128
vRtrRsvpIfStatTxBundles
The total number of RSVP bundled
packets that have been transmitted on
this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatRxErrorPkts
The total number of RSVP packets with
errors received on this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatTxErrorPkts
The total number of RSVP packets with
errors that have been transmitted on this
RSVP interface.
hellos
UINT128
vRtrRsvpIfStatRxHelloReq
s
The total number of RSVP HELLO REQ
messages received on this RSVP interface.
hellos
UINT128
vRtrRsvpIfStatTxHelloReq
s
The total number of RSVP HELLO REQ
packets that have been transmitted on
this RSVP interface.
helloTimeout
long
vRtrRsvpIfStatHelloTimeo
ut
The total number of hello messages that
timed out on this RSVP interface.
packets
UINT128
vRtrRsvpIfStatRxPkts
The total number of error free RSVP
packets received on this RSVP interface.
packets
UINT128
vRtrRsvpIfStatTxPkts
The total number of error free RSVP
packets that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatRxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatTxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted
from this RSVP interface.
(1 of 5)
B-54
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
paths
UINT128
vRtrRsvpIfStatRxPaths
The total number of RSVP PATH messages
that have been received on this RSVP
interface.
paths
UINT128
vRtrRsvpIfStatTxPaths
The total number of RSVP PATH messages
that have been transmitted from this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatRxPathTear
s
The total number of RSVP PATH TEAR
messages that have been received on this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatTxPathTear
s
The total number of RSVP PATH TEAR
messages that have been transmitted
from this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatRxSRefresh
es
The total number of RSVP summary
refresh, SREFRESH, messages received on
this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatTxSRefresh
es
The total number of summary refresh,
SREFRESH, messages that have been
transmitted on this RSVP interface when
refresh reduction is enabled.
reserveConfirms
UINT128
vRtrRsvpIfStatRxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been received on this
RSVP interface.
reserveConfirms
UINT128
vRtrRsvpIfStatTxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been transmitted
from this RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatRxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been received on this
RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatTxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been transmitted
from this RSVP interface.
reserves
UINT128
vRtrRsvpIfStatRxResvs
The total number of RSVP RESV messages
that have been received on this RSVP
interface.
reserves
UINT128
vRtrRsvpIfStatTxResvs
The total number of RSVP RESV messages
that have been transmitted from this
RSVP interface.
reserveTears
UINT128
vRtrRsvpIfStatRxResvTear
s
The total number of RSVP RESV TEAR
messages that have been received on this
RSVP interface.
reserveTears
UINT128
vRtrRsvpIfStatTxResvTear
s
The total number of RSVP RESV TEAR
messages that have been transmitted
from this RSVP interface.
totalPackets
UINT128
vRtrRsvpIfStatRxTotalPkt
s
The total number of RSVP packets,
including errors, received on this RSVP
interface.
totalPackets
UINT128
vRtrRsvpIfStatTxTotalPkt
s
The total number of RSVP packets,
including error packets, that have been
transmitted on this RSVP interface.
RsvpInterfaceStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfTable
Monitored class: rsvp.Interface
(2 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-55
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
activeReservations
long
vRtrRsvpIfActiveReservati
onCount
The total number of active RSVP sessions
that have reserved bandwidth.
activeSessions
long
vRtrRsvpIfActiveSessionC
ount
The total number of active RSVP sessions
on this interface. This count includes
sessions that have requested bandwidth
as well as sessions that have not
requested any bandwidth.
bandwidth
long
vRtrRsvpIfBandwidth
The value of vRtrRsvpIfBandwidth
specifies the amount of bandwidth in
mega-bits per second (Mbps) available to
be reserved for the RSVP protocol on this
interface. This is typically the (portSpeed
* subscriptionPercentage).
reservedBandwidth
long
vRtrRsvpIfReservedBandw
idth
The value of
vRtrRsvpIfReservedBandwidth specifies
the amount of bandwidth in mega-bits per
second (Mbps) to reserved by the RSVP
sessions on this interface. A value of zero
(0) indicates that no bandwidth is
reserved.
totalSessions
long
vRtrRsvpIfTotalSessionCo
unt
The total number of RSVP sessions on this
interface. This count includes sessions
that are active as well as sessions that
have been signalled but a response has
not yet been received.
RsvpInterfaceTransmitStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfStatTable
Monitored class: rsvp.Interface
acks
UINT128
vRtrRsvpIfStatRxAcks
The total number of RSVP ACK messages
received when refresh reduction is
enabled on this RSVP interface.
acks
UINT128
vRtrRsvpIfStatTxAcks
The total number of RSVP ACK messages
that have been transmitted on this RSVP
interface when refresh reduction is
enabled.
bundles
UINT128
vRtrRsvpIfStatRxBundles
The total number of RSVP bundled
packets received on this RSVP interface.
Bundled packets are sent when refresh
reduction is enabled.
bundles
UINT128
vRtrRsvpIfStatTxBundles
The total number of RSVP bundled
packets that have been transmitted on
this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatRxErrorPkts
The total number of RSVP packets with
errors received on this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatTxErrorPkts
The total number of RSVP packets with
errors that have been transmitted on this
RSVP interface.
hellos
UINT128
vRtrRsvpIfStatRxHelloReq
s
The total number of RSVP HELLO REQ
messages received on this RSVP interface.
hellos
UINT128
vRtrRsvpIfStatTxHelloReq
s
The total number of RSVP HELLO REQ
packets that have been transmitted on
this RSVP interface.
(3 of 5)
B-56
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
packets
UINT128
vRtrRsvpIfStatRxPkts
The total number of error free RSVP
packets received on this RSVP interface.
packets
UINT128
vRtrRsvpIfStatTxPkts
The total number of error free RSVP
packets that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatRxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatTxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted
from this RSVP interface.
paths
UINT128
vRtrRsvpIfStatRxPaths
The total number of RSVP PATH messages
that have been received on this RSVP
interface.
paths
UINT128
vRtrRsvpIfStatTxPaths
The total number of RSVP PATH messages
that have been transmitted from this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatRxPathTear
s
The total number of RSVP PATH TEAR
messages that have been received on this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatTxPathTear
s
The total number of RSVP PATH TEAR
messages that have been transmitted
from this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatRxSRefresh
es
The total number of RSVP summary
refresh, SREFRESH, messages received on
this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatTxSRefresh
es
The total number of summary refresh,
SREFRESH, messages that have been
transmitted on this RSVP interface when
refresh reduction is enabled.
reserveConfirms
UINT128
vRtrRsvpIfStatRxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been received on this
RSVP interface.
reserveConfirms
UINT128
vRtrRsvpIfStatTxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been transmitted
from this RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatRxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been received on this
RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatTxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been transmitted
from this RSVP interface.
reserves
UINT128
vRtrRsvpIfStatRxResvs
The total number of RSVP RESV messages
that have been received on this RSVP
interface.
reserves
UINT128
vRtrRsvpIfStatTxResvs
The total number of RSVP RESV messages
that have been transmitted from this
RSVP interface.
reserveTears
UINT128
vRtrRsvpIfStatRxResvTear
s
The total number of RSVP RESV TEAR
messages that have been received on this
RSVP interface.
(4 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-57
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
reserveTears
UINT128
vRtrRsvpIfStatTxResvTear
s
The total number of RSVP RESV TEAR
messages that have been transmitted
from this RSVP interface.
totalPackets
UINT128
vRtrRsvpIfStatRxTotalPkt
s
The total number of RSVP packets,
including errors, received on this RSVP
interface.
totalPackets
UINT128
vRtrRsvpIfStatTxTotalPkt
s
The total number of RSVP packets,
including error packets, that have been
transmitted on this RSVP interface.
RsvpSessionStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpSessionStatTable
Monitored class: rsvp.Session
detourAge
long
vRtrRsvpSessionDetourAg
e
vRtrRsvpSessionDetourAge is the age
(i.e., time from creation till now) of this
detour LSP in 10-millisecond periods.
detourTimeUp
long
vRtrRsvpSessionDetourTi
meUp
vRtrRsvpSessionDetourTimeUp is the total
time in 10-millisecond units that the
detour LSP has been operational.
pathsReceived
UINT128
vRtrRsvpSessionRxPaths
The total number of RSVP PATH messages
received for this RSVP session.
pathsTransmitted
UINT128
vRtrRsvpSessionTxPaths
The total number of RSVP PATH messages
transmitted for this RSVP session.
reservesReceived
UINT128
vRtrRsvpSessionRxResvs
The total number of RSVP RESV messages
received for this RSVP session.
reservesTransmitted
UINT128
vRtrRsvpSessionTxResvs
The total number of RSVP RESV messages
transmitted for this RSVP session.
(5 of 5)
Table B-13 rtr statistics
5620 SAM counter name
Type
MIB counter name
Description
NetworkInterfaceIngressStats
MIB table name: TIMETRA-SAS-VRTR-MIB.vRtrNetIfIngressStatsTable
Monitored class: rtr.NetworkInterface
ingressFwdInProfPkts
UINT128
vRtrNetIfIngressFwdInPro
fPkts
vRtrNetIfIngressFwdInProfPkts indicates
the number of conforming network
interface ingress packets forwarded on
this router interface using this meter.
ingressFwdOutProfPkts
UINT128
vRtrNetIfIngressFwdOutPr
ofPkts
vRtrNetIfIngressFwdOutProfPkts indicates
the number of exceeding network
interface ingress packets forwarded on
this router interface using this meter.
ingressMeterIndex
long
vRtrNetIfIngressMeterInd
ex
vRtrNetIfIngressMeterIndex serves as the
tertiary index. When used in conjunction
with vRtrID and vRtrIfIndex, it uniquely
identifies a network ingress meter for the
specified router interface in the managed
system.
(1 of 3)
B-58
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
RouteStats
MIB table name: TIMETRA-VRTR-MIB.vRtrStatTable
Monitored classes:
•
•
rtr.VirtualRouter
vprn.Site
activeARPEntries
long
vRtrStatActiveARPEntries
vRtrStatActiveARPEntries indicates the
number of active ARP entries for the
specified virtual router in the system.
aggregateActiveRoutes
long
vRtrAggregateActiveRout
es
vRtrAggregateActiveRoutes indicates the
current number of active aggregate
routes for this instance of the route table.
aggregateRoutes
long
vRtrAggregateRoutes
vRtrAggregateRoutes indicates the
current number of aggregate routes for
this instance of the route table.
directActiveRoutes
long
vRtrDirectActiveRoutes
vRtrDirectActiveRoutes indicates the
current number of active direct routes for
this instance of the route table.
directRoutes
long
vRtrDirectRoutes
vRtrDirectRoutes indicates the current
number of direct routes for this instance
of the route table.
illegalLabelsReceived
long
vRtrStatIllegalLabels
vRtrStatIllegalLabels indicates the
number of illegally received labels on this
virtual router.
isisActiveRoutes
long
vRtrISISActiveRoutes
vRtrISISActiveRoutes indicates the
current number of active isis routes for
this instance of the route table.
isisRoutes
long
vRtrISISRoutes
vRtrISISRoutes indicates the current
number of isis routes for this instance of
the route table.
ldpActiveTunnels
long
vRtrStatActiveLdpTunnels
vRtrStatActiveLdpTunnels indicates the
current number of rows in the
vRtrTunnelTable where vRtrTunnelType
has a value of 'ldp'.
ldpTunnels
long
vRtrStatTotalLdpTunnels
vRtrStatTotalLdpTunnels indicates the
current number of both active and
inactive LDP tunnels.
ospfActiveRoutes
long
vRtrOSPFActiveRoutes
vRtrOSPFActiveRoutes indicates the
current number of active ospf routes for
this instance of the route table.
ospfRoutes
long
vRtrOSPFRoutes
vRtrOSPFRoutes indicates the current
number of ospf routes for this instance of
the route table.
routerInterfacesActive
long
vRtrStatActiveIfs
vRtrStatActiveIfs indicates the current
number of router interfaces with
vRtrIfAdminState equal 'inService' on this
virtual router.
routerInterfacesConfigured
long
vRtrStatConfiguredIfs
vRtrStatConfiguredIfs indicates the
current number of router interfaces
configured on this virtual router.
routesInVrf
long
vRtrStatCurrNumRoutes
vRtrStatCurrNumRoutes indicates the
current number of routes in the VRF for
this virtual router.
(2 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-59
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpActiveTunnels
long
vRtrStatActiveSdpTunnels
vRtrStatActiveSdpTunnels indicates the
current number of rows in the
vRtrTunnelTable where vRtrTunnelType
has a value of 'sdp'.
sdpTunnels
long
vRtrStatTotalSdpTunnels
vRtrStatTotalSdpTunnels indicates the
current number of both active and
inactive SDP tunnels.
staticActiveRoutes
long
vRtrStaticActiveRoutes
vRtrStaticActiveRoutes indicates the
current number of active static routes for
this instance of the route table.
staticRoutes
long
vRtrStaticRoutes
vRtrStaticRoutes indicates the current
number of static routes for this instance
of the route table.
totalARPEntries
long
vRtrStatTotalARPEntries
vRtrStatTotalARPEntries indicates the
total number of active and inactive ARP
entries for the specified virtual router in
the system.
(3 of 3)
Table B-14 service statistics
5620 SAM counter name
Type
MIB counter name
Description
ServiceSapIngQosPlcyStats
MIB table name: TIMETRA-SAS-QOS-MIB.sapIngQosMeterStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
forwardedInProfOctets
UINT128
sapIngQosMeterStatsForw
ardedInProfOctets
The number of in-profile octets (rate
below CIR) forwarded by the ingress
Qchip.
forwardedInProfPackets
UINT128
sapIngQosMeterStatsForw
ardedInProfPackets
The number of in-profile packets (rate
below CIR) forwarded by the ingress
Qchip.
forwardedOutProfOctets
UINT128
sapIngQosMeterStatsForw
ardedOutProfOctets
The number of out-of-profile octets (rate
above CIR) forwarded by the ingress
Qchip.
forwardedOutProfPackets
UINT128
sapIngQosMeterStatsForw
ardedOutProfPackets
The number of out-of-profile packets
(rate above CIR) forwarded by the ingress
Qchip.
meterId
long
sapIngQosMeterId
The index of the ingress QoS meter of this
SAP.
B-60
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
Table B-15 sitesec statistics
5620 SAM counter name
Type
MIB counter name
Description
CpmFilterQueueStats
MIB table name: TIMETRA-SECURITY-MIB.tCpmFilterQueueStatsTable
Monitored class: sitesec.CpmFilterQueue
droppedInOctets
UINT128
tCpmFilterQInProfileDrop
Octets
The value of
tCpmFilterQInProfileDropOctets indicates
the number of octets complying to the
queue Qos profile dropped from the
tCpmFilterQueueEntry with the same
index.
droppedInPackets
UINT128
tCpmFilterQInProfileDrop
Pkts
The value of
tCpmFilterQInProfileDropPkts indicates
the number of packets complying to the
queue Qos profile dropped from the
tCpmFilterQueueEntry with the same
index.
droppedOutOctets
UINT128
tCpmFilterQOutProfileDr
opOctets
The value of
tCpmFilterQOutProfileDropOctets
indicates the number of octets not
complying to the queue Qos profile
dropped from the tCpmFilterQueueEntry
with the same index.
droppedOutPackets
UINT128
tCpmFilterQOutProfileDr
opPkts
The value of
tCpmFilterQOutProfileDropPkts indicates
the number of packets not complying to
the queue Qos profile dropped from the
tCpmFilterQueueEntry with the same
index.
forwardedInOctets
UINT128
tCpmFilterQInProfileFwd
Octets
The value of
tCpmFilterQInProfileFwdOctets indicates
the number of octets complying to the
queue Qos profile forwarded from the
tCpmFilterQueueEntry with the same
index.
forwardedInPackets
UINT128
tCpmFilterQInProfileFwd
Pkts
The value of tCpmFilterQInProfileFwdPkts
indicates the number of packets
complying to the queue Qos profile
forwarded from the
tCpmFilterQueueEntry with the same
index.
forwardedOutOctets
UINT128
tCpmFilterQOutProfileFw
dOctets
The value of
tCpmFilterQOutProfileFwdOctets
indicates the number of octets not
complying to the queue Qos profile
forwarded from the
tCpmFilterQueueEntry with the same
index.
forwardedOutPackets
UINT128
tCpmFilterQOutProfileFw
dPkts
The value of
tCpmFilterQOutProfileFwdPkts indicates
the number of packets not complying to
the queue Qos profile forwarded from the
tCpmFilterQueueEntry with the same
index.
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-61
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
CpmIpFilterStats
MIB table name: TIMETRA-SECURITY-MIB.tCpmIpFilterStatsTable
Monitored class: sitesec.CpmIpFilterEntry
droppedPackets
UINT128
tCpmIpFilterStatsDroppe
dPkts
The value of
tCpmIpFilterStatsDroppedPkts indicates
the number of packets dropped due to the
tCpmIpFilterEntry with the same index.
forwardedPackets
UINT128
tCpmIpFilterStatsForward
edPkts
The value of
tCpmIpFilterStatsForwardedPkts
indicates the number of packets
forwarded due to the tCpmIpFilterEntry
with the same index.
MafEntryStats
MIB table name: TIMETRA-SECURITY-MIB.tmnxMafMatchTable
Monitored class: sitesec.MafEntry
matchCount
UINT128
tmnxMafMatchCount
The value of tmnxMafMatchCount
indicates the number of times a
management packet has matched this
filter entry.
(2 of 2)
Table B-16 svt statistics
5620 SAM counter name
Type
MIB counter name
Description
MirrorSdpBindingStats
MIB table name: TIMETRA-SERV-MIB.sdpBindBaseStatsTable
Monitored class: svt.MirrorSdpBinding
egressForwardedOctets
UINT128
sdpBindBaseStatsEgressF
orwardedOctets
.
egressForwardedPackets
UINT128
sdpBindBaseStatsEgressF
orwardedPackets
.
ingressDroppedOctets
UINT128
sdpBindBaseStatsIngDrop
Octets
.
ingressDroppedPackets
UINT128
sdpBindBaseStatsIngressD
roppedPackets
.
ingressForwardedOctets
UINT128
sdpBindBaseStatsIngFwdO
ctets
.
ingressForwardedPackets
UINT128
sdpBindBaseStatsIngressF
orwardedPackets
.
SdpBindingBaseStats
MIB table name: TIMETRA-SERV-MIB.sdpBindBaseStatsTable
Monitored classes:
•
•
svt.SpokeSdpBinding
svt.MeshSdpBinding
egressForwardedOctets
UINT128
sdpBindBaseStatsEgressF
orwardedOctets
.
egressForwardedPackets
UINT128
sdpBindBaseStatsEgressF
orwardedPackets
.
(1 of 2)
B-62
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
B. 7210 SAS-M Release 1.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingressDroppedOctets
UINT128
sdpBindBaseStatsIngDrop
Octets
.
ingressDroppedPackets
UINT128
sdpBindBaseStatsIngressD
roppedPackets
.
ingressForwardedOctets
UINT128
sdpBindBaseStatsIngFwdO
ctets
.
ingressForwardedPackets
UINT128
sdpBindBaseStatsIngressF
orwardedPackets
.
TunnelKeepAliveStats
MIB table name: TIMETRA-SERV-MIB.sdpInfoTable
Monitored class: svt.Tunnel
lateHelloResponses
long
sdpKeepAliveNumLateHel
loResponseMessages
The number of SDP Echo Response
messages received after the
corresponding Request timeout timer
expired.
receivedHelloMessages
long
sdpKeepAliveNumHelloRe
sponseMessages
The number of SDP Echo Response
messages received since the keep-alive
was administratively enabled or the
counter was cleared.
transmittedHelloMessages
long
sdpKeepAliveNumHelloRe
questMessages
The number of SDP Echo Request
messages transmitted since the
keep-alive was administratively enabled
or the counter was cleared.
(2 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
B-63
B. 7210 SAS-M Release 1.0 statistics counters
B-64
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
C.
7250 SAS Release 2.0 statistics
counters
C.1 7250 SAS Release 2.0 statistics counters
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
C-2
C-1
C. 7250 SAS Release 2.0 statistics counters
C.1
7250 SAS Release 2.0 statistics counters
This appendix lists in tabular form the statistics counters that the 5620 SAM supports
for the 7250 SAS, Release 2.0. Each 5620 SAM counter entry in a table contains the
name and description of the corresponding device MIB counter.
The 5620 SAM counter name in a table entry is the internal counter identifier that is
required for statistics retrieval through the 5620 SAM OSSI. The displayed counter
name in the 5620 SAM GUI is typically an expansion of this identifier. For example,
the receivedBroadcastPackets counter name in the equipment table corresponds to
the Received Broadcast Packets counter name on the Log Record form for an
Ethernet port.
Note 1 — The tables list the 5620 SAM-supported statistics counters
for the current release of the device. Counters that are supported for a
previous device release, but not for the current release, are not listed.
Note 2 — A statistics counter in the 5620 SAM GUI whose displayed
name ends with “Periodic” is a counter that records the difference
between the current and previous values of an associated 5620 SAM
counter. The OSS equivalent name for a Periodic counter is the name
of the 5620 SAM counter with a “Periodic” suffix. The tables in this
appendix do not list Periodic counters.
Table C-1 lists each statistics package and the associated statistics-counter table.
Table C-1 Statistics packages and counter tables
Package name
See
equipment
Table C-2
ethernetequipment
Table C-3
Table C-2 equipment statistics
5620 SAM counter name
Type
MIB counter name
Description
BatmL2InterfaceStats
MIB table name: BATM-SWITCH-MIB.reportsL2IfaceTable
Monitored class: equipment.PhysicalPort
broadcastPkts
long
reportsL2IfaceStatsBroad
castPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
(1 of 6)
C-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
reportsL2IfaceStatsCollisi
ons
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the RMON
probe's location. Sections 8.2.1.3
(10BASE-5) and 10.3.1.3 (10BASE-2) of
IEEE standard 802.3 states that a station
must detect a collision in the receive
mode if three or more stations are
transmitting simultaneously. A repeater
port must detect a collision when two or
more stations are transmitting
simultaneously. Thus a probe placed on a
repeater port could record more collisions
than a probe connected to a station on
the same segment would. Probe location
plays a much smaller role when
considering 10BASE-T. Section 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coaxial
segments to which the repeater is
connected.
cRCAlignErrors
long
reportsL2IfaceStatsCRCAl
ignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
reportsL2IfaceStatsDropE
vents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
reportsL2IfaceStatsFragm
ents
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(2 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
C-3
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
reportsL2IfaceStatsJabbe
rs
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different from the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
in which any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPkts
long
reportsL2IfaceStatsMultic
astPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
octets
long
reportsL2IfaceStatsOctet
s
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
Ethernet utilization. If greater precision is
desired, the etherStatsPkts and
etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
Ethernet segment utilization which is the
percent utilization of the ethernet
segment on a 0 to 100 percent scale.
oversizePkts
long
reportsL2IfaceStatsOversi
zePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
pkts
long
reportsL2IfaceStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
pkts1024to1518Octets
long
reportsL2IfaceStatsPkts1
024to1518Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts128to255Octets
long
reportsL2IfaceStatsPkts1
28to255Octets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
(3 of 6)
C-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
pkts256to511Octets
long
reportsL2IfaceStatsPkts2
56to511Octets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts512to1023Octets
long
reportsL2IfaceStatsPkts5
12to1023Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts64Octets
long
reportsL2IfaceStatsPkts6
4Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
pkts65to127Octets
long
reportsL2IfaceStatsPkts6
5to127Octets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
rXOctetsNoErr
long
reportsL2IfaceRXOctetsN
oErr
The number of octets received on the
interface. This number does not include
octets with errors.
rXPacketsNoErr
long
reportsL2IfaceRXPackets
NoErr
The number of packets received on the
interface. This number does not include
packets with errors.
tXOctetsNoErr
long
reportsL2IfaceTXOctetsN
oErr
The number of octets transmitted from
the interface. This number does not
include octets with errors.
tXPacketsNoErr
long
reportsL2IfaceTXPackets
NoErr
The number of packets transmitted from
the interface. This number does not
include packets with errors.
undersizePkts
long
reportsL2IfaceStatsUnder
sizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
InterfaceAdditionalStats
MIB table name: IF-MIB.ifXTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
receivedBroadcastPackets
UINT128
ifHCInBroadcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a broadcast address at
this sub-layer. This object is a 64-bit
version of ifInBroadcastPkts.
receivedMulticastPackets
UINT128
ifHCInMulticastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a multicast address at
this sub-layer. For a MAC layer protocol,
this includes both Group and Functional
addresses. This object is a 64-bit version
of ifInMulticastPkts.
(4 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
C-5
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedTotalOctets
UINT128
ifHCInOctets
The total number of octets received on
the interface, including framing
characters. This object is a 64-bit version
of ifInOctets.
receivedUnicastPackets
UINT128
ifHCInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer. This
object is a 64-bit version of ifInUcastPkts.
transmittedBroadcastPackets
UINT128
ifHCOutBroadcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a broadcast address at this sub-layer,
including those that were discarded or not
sent. This object is a 64-bit version of
ifOutBroadcastPkts.
transmittedMulticastPackets
UINT128
ifHCOutMulticastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a multicast address at this sub-layer,
including those that were discarded or not
sent. For a MAC layer protocol, this
includes both Group and Functional
addresses. This object is a 64-bit version
of ifOutMulticastPkts.
transmittedTotalOctets
UINT128
ifHCOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. This object is a 64-bit version
of ifOutOctets.
transmittedUnicastPackets
UINT128
ifHCOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent. This
object is a 64-bit version of
ifOutUcastPkts.
InterfaceStats
MIB table name: RFC1213-MIB.ifTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
outboundBadPackets
long
ifOutErrors
The number of outbound packets that
could not be transmitted because of
errors.
outboundPacketsDiscarded
long
ifOutDiscards
The number of outbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being transmitted. One possible
reason for discarding such a packet could
be to free up buffer space.
receivedBadPackets
long
ifInErrors
The number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol.
(5 of 6)
C-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedOctets
long
ifInOctets
The total number of octets received on
the interface, including framing
characters.
receivedPacketsDiscarded
long
ifInDiscards
The number of inbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being deliverable to a higher-layer
protocol. One possible reason for
discarding such a packet could be to free
up buffer space.
receivedUnicastPackets
long
ifInUcastPkts
The number of subnetwork-unicast
packets delivered to a higher-layer
protocol.
receivedUnknownProtocolPackets
long
ifInUnknownProtos
The number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
transmittedOctets
long
ifOutOctets
The total number of octets transmitted
out of the interface, including framing
characters.
transmittedUnicastPackets
long
ifOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted to a subnetwork-unicast
address, including those that were
discarded or not sent.
(6 of 6)
Table C-3 ethernetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
etherStatsBroadcastPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
EthernetStats
MIB table name: RMON-MIB.etherStatsTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
broadcastPackets
long
(1 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
C-7
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
etherStatsCollisions
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the
location of the RMON probe. Section
8.2.1.3 (10BASE-5) and section 10.3.1.3
(10BASE-2) of IEEE standard 802.3 states
that a station must detect a collision, in
the receive mode, if three or more
stations are transmitting simultaneously.
A repeater port must detect a collision
when two or more stations are
transmitting simultaneously. Thus a probe
placed on a repeater port could record
more collisions than a probe connected to
a station on the same segment would.
Probe location plays a much smaller role
when considering 10BASE-T. 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments
to which the repeater is connected.
crcAlignErrors
long
etherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
etherStatsDropEvents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
etherStatsFragments
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(2 of 4)
C-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
etherStatsJabbers
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different than the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
where any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPackets
long
etherStatsMulticastPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
oversizePackets
long
etherStatsOversizePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
packets1024to1518Octets
long
etherStatsPkts1024to151
8Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets128to255Octets
long
etherStatsPkts128to255O
ctets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
long
etherStatsPkts256to511O
ctets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
long
etherStatsPkts512to1023
Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
long
etherStatsPkts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
long
etherStatsPkts65to127Oc
tets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(3 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
C-9
C. 7250 SAS Release 2.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
long
etherStatsOctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
10-Megabit ethernet utilization. If greater
precision is desired, the etherStatsPkts
and etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent.
totalPackets
long
etherStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
undersizePackets
long
etherStatsUndersizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
(4 of 4)
C-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
D.
7250 SAS-ES and 7250 SAS-ESA
Release 3.0 statistics counters
D.1 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics
counters
D-2
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
D-1
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
D.1
7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics
counters
This appendix lists in tabular form the statistics counters that the 5620 SAM supports
for the 7250 SAS-ES and 7250 SAS-ESA, Release 3.0. Each 5620 SAM counter
entry in a table contains the name and description of the corresponding device MIB
counter.
The 5620 SAM counter name in a table entry is the internal counter identifier that is
required for statistics retrieval through the 5620 SAM OSSI. The displayed counter
name in the 5620 SAM GUI is typically an expansion of this identifier. For example,
the receivedBroadcastPackets counter name in the equipment table corresponds to
the Received Broadcast Packets counter name on the Log Record form for an
Ethernet port.
Note 1 — The tables list the 5620 SAM-supported statistics counters
for the current release of the device. Counters that are supported for a
previous device release, but not for the current release, are not listed.
Note 2 — A statistics counter in the 5620 SAM GUI whose displayed
name ends with “Periodic” is a counter that records the difference
between the current and previous values of an associated 5620 SAM
counter. The OSS equivalent name for a Periodic counter is the name
of the 5620 SAM counter with a “Periodic” suffix. The tables in this
appendix do not list Periodic counters.
Table D-1 lists each statistics package and the associated statistics-counter table.
Table D-1 Statistics packages and counter tables
Package name
See
equipment
Table D-2
ethernetequipment
Table D-3
Table D-2 equipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AllocatedMemoryStats
MIB table name: BATM-SYS-INFO-MIB.numBytesAlloc
Monitored class: equipment.SystemStatsHolder
allocatedMemory
long
numBytesAlloc
The number of bytes of system memory
that have been allocated by tasks and
system services.
AvailableMemoryStats
MIB table name: BATM-SYS-INFO-MIB.numBytesFree
Monitored class: equipment.SystemStatsHolder
availableMemory
long
numBytesFree
The number of bytes free in the system
memory.
(1 of 6)
D-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
BatmL2InterfaceStats
MIB table name: BATM-SWITCH-MIB.reportsL2IfaceTable
Monitored class: equipment.PhysicalPort
broadcastPkts
long
reportsL2IfaceStatsBroad
castPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
collisions
long
reportsL2IfaceStatsCollisi
ons
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the RMON
probe's location. Sections 8.2.1.3
(10BASE-5) and 10.3.1.3 (10BASE-2) of
IEEE standard 802.3 states that a station
must detect a collision in the receive
mode if three or more stations are
transmitting simultaneously. A repeater
port must detect a collision when two or
more stations are transmitting
simultaneously. Thus a probe placed on a
repeater port could record more collisions
than a probe connected to a station on
the same segment would. Probe location
plays a much smaller role when
considering 10BASE-T. Section 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coaxial
segments to which the repeater is
connected.
cRCAlignErrors
long
reportsL2IfaceStatsCRCAl
ignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
reportsL2IfaceStatsDropE
vents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
(2 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
D-3
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
fragments
long
reportsL2IfaceStatsFragm
ents
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
jabbers
long
reportsL2IfaceStatsJabbe
rs
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different from the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
in which any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPkts
long
reportsL2IfaceStatsMultic
astPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
octets
long
reportsL2IfaceStatsOctet
s
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
Ethernet utilization. If greater precision is
desired, the etherStatsPkts and
etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
Ethernet segment utilization which is the
percent utilization of the ethernet
segment on a 0 to 100 percent scale.
oversizePkts
long
reportsL2IfaceStatsOversi
zePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
pkts
long
reportsL2IfaceStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
(3 of 6)
D-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
pkts1024to1518Octets
long
reportsL2IfaceStatsPkts1
024to1518Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts128to255Octets
long
reportsL2IfaceStatsPkts1
28to255Octets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts256to511Octets
long
reportsL2IfaceStatsPkts2
56to511Octets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts512to1023Octets
long
reportsL2IfaceStatsPkts5
12to1023Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
pkts64Octets
long
reportsL2IfaceStatsPkts6
4Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
pkts65to127Octets
long
reportsL2IfaceStatsPkts6
5to127Octets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
rXOctetsNoErr
long
reportsL2IfaceRXOctetsN
oErr
The number of octets received on the
interface. This number does not include
octets with errors.
rXPacketsNoErr
long
reportsL2IfaceRXPackets
NoErr
The number of packets received on the
interface. This number does not include
packets with errors.
tXOctetsNoErr
long
reportsL2IfaceTXOctetsN
oErr
The number of octets transmitted from
the interface. This number does not
include octets with errors.
tXPacketsNoErr
long
reportsL2IfaceTXPackets
NoErr
The number of packets transmitted from
the interface. This number does not
include packets with errors.
undersizePkts
long
reportsL2IfaceStatsUnder
sizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
InterfaceAdditionalStats
MIB table name: IF-MIB.ifXTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
(4 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
D-5
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedBroadcastPackets
UINT128
ifHCInBroadcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a broadcast address at
this sub-layer. This object is a 64-bit
version of ifInBroadcastPkts.
receivedMulticastPackets
UINT128
ifHCInMulticastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a multicast address at
this sub-layer. For a MAC layer protocol,
this includes both Group and Functional
addresses. This object is a 64-bit version
of ifInMulticastPkts.
receivedTotalOctets
UINT128
ifHCInOctets
The total number of octets received on
the interface, including framing
characters. This object is a 64-bit version
of ifInOctets.
receivedUnicastPackets
UINT128
ifHCInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer. This
object is a 64-bit version of ifInUcastPkts.
transmittedBroadcastPackets
UINT128
ifHCOutBroadcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a broadcast address at this sub-layer,
including those that were discarded or not
sent. This object is a 64-bit version of
ifOutBroadcastPkts.
transmittedMulticastPackets
UINT128
ifHCOutMulticastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a multicast address at this sub-layer,
including those that were discarded or not
sent. For a MAC layer protocol, this
includes both Group and Functional
addresses. This object is a 64-bit version
of ifOutMulticastPkts.
transmittedTotalOctets
UINT128
ifHCOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. This object is a 64-bit version
of ifOutOctets.
transmittedUnicastPackets
UINT128
ifHCOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent. This
object is a 64-bit version of
ifOutUcastPkts.
InterfaceStats
MIB table name: RFC1213-MIB.ifTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
(5 of 6)
D-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
outboundBadPackets
long
ifOutErrors
The number of outbound packets that
could not be transmitted because of
errors.
outboundPacketsDiscarded
long
ifOutDiscards
The number of outbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being transmitted. One possible
reason for discarding such a packet could
be to free up buffer space.
receivedBadPackets
long
ifInErrors
The number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol.
receivedOctets
long
ifInOctets
The total number of octets received on
the interface, including framing
characters.
receivedPacketsDiscarded
long
ifInDiscards
The number of inbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being deliverable to a higher-layer
protocol. One possible reason for
discarding such a packet could be to free
up buffer space.
receivedUnicastPackets
long
ifInUcastPkts
The number of subnetwork-unicast
packets delivered to a higher-layer
protocol.
receivedUnknownProtocolPackets
long
ifInUnknownProtos
The number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
transmittedOctets
long
ifOutOctets
The total number of octets transmitted
out of the interface, including framing
characters.
transmittedUnicastPackets
long
ifOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted to a subnetwork-unicast
address, including those that were
discarded or not sent.
(6 of 6)
Table D-3 ethernetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
etherStatsBroadcastPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
EthernetStats
MIB table name: RMON-MIB.etherStatsTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
broadcastPackets
long
(1 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
D-7
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
etherStatsCollisions
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the
location of the RMON probe. Section
8.2.1.3 (10BASE-5) and section 10.3.1.3
(10BASE-2) of IEEE standard 802.3 states
that a station must detect a collision, in
the receive mode, if three or more
stations are transmitting simultaneously.
A repeater port must detect a collision
when two or more stations are
transmitting simultaneously. Thus a probe
placed on a repeater port could record
more collisions than a probe connected to
a station on the same segment would.
Probe location plays a much smaller role
when considering 10BASE-T. 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments
to which the repeater is connected.
crcAlignErrors
long
etherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
etherStatsDropEvents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
etherStatsFragments
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(2 of 4)
D-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
etherStatsJabbers
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different than the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
where any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPackets
long
etherStatsMulticastPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
oversizePackets
long
etherStatsOversizePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
packets1024to1518Octets
long
etherStatsPkts1024to151
8Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets128to255Octets
long
etherStatsPkts128to255O
ctets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
long
etherStatsPkts256to511O
ctets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
long
etherStatsPkts512to1023
Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
long
etherStatsPkts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
long
etherStatsPkts65to127Oc
tets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(3 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
D-9
D. 7250 SAS-ES and 7250 SAS-ESA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
long
etherStatsOctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
10-Megabit ethernet utilization. If greater
precision is desired, the etherStatsPkts
and etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent.
totalPackets
long
etherStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
undersizePackets
long
etherStatsUndersizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
(4 of 4)
D-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E.
7450 ESS Release 7.0 statistics
counters
E.1 7450 ESS Release 7.0 statistics counters
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-2
E-1
E. 7450 ESS Release 7.0 statistics counters
E.1
7450 ESS Release 7.0 statistics counters
This appendix lists in tabular form the statistics counters that the 5620 SAM supports
for the 7450 ESS, Release 7.0. Each 5620 SAM counter entry in a table contains the
name and description of the corresponding device MIB counter.
The 5620 SAM counter name in a table entry is the internal counter identifier that is
required for statistics retrieval through the 5620 SAM OSSI. The displayed counter
name in the 5620 SAM GUI is typically an expansion of this identifier. For example,
the receivedBroadcastPackets counter name in the equipment table corresponds to
the Received Broadcast Packets counter name on the Log Record form for an
Ethernet port.
Note 1 — The tables list the 5620 SAM-supported statistics counters
for the current release of the device. Counters that are supported for a
previous device release, but not for the current release, are not listed.
Note 2 — A statistics counter in the 5620 SAM GUI whose displayed
name ends with “Periodic” is a counter that records the difference
between the current and previous values of an associated 5620 SAM
counter. The OSS equivalent name for a Periodic counter is the name
of the 5620 SAM counter with a “Periodic” suffix. The tables in this
appendix do not list Periodic counters.
Table E-1 lists each statistics package and the associated statistics-counter table.
Table E-1 Statistics packages and counter tables
Package name
See
aapolicy
Table E-2
aclfilter
Table E-3
aps
Table E-4
bgp
Table E-5
equipment
Table E-6
ethernetequipment
Table E-7
fr
Table E-8
gsmp
Table E-9
isa
Table E-10
isis
Table E-11
l2fib
Table E-12
l2fwd
Table E-13
lag
Table E-14
ldp
Table E-15
lldp
Table E-16
mpls
Table E-17
multicast
Table E-18
(1 of 2)
E-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
Package name
See
multichassis
Table E-19
ospf
Table E-20
pae802_1x
Table E-21
ppp
Table E-22
radiusaccounting
Table E-23
ressubscr
Table E-24
rip
Table E-25
rsvp
Table E-26
rtr
Table E-27
service
Table E-28
sitesec
Table E-29
sonetequipment
Table E-30
subscrauth
Table E-31
svq
Table E-32
svt
Table E-33
vpls
Table E-34
vrrp
Table E-35
(2 of 2)
Table E-2 aapolicy statistics
5620 SAM counter name
Type
MIB counter name
Description
BsxAaAccountingStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxStatAaTable
Monitored classes:
•
•
•
aapolicy.Application
aapolicy.ApplicationGroup
aapolicy.ApplicationAssuranceProtocol
numOfSubscribers
long
tmnxBsxStatAaNumSubscr
ibers
The value of
tmnxBsxStatAaNumSubscribers indicates
the number of subscribers at the most
recent 5-minute snapshot of statistics.
BsxAppQosPolicyStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxAqpStatsTable
Monitored class: aapolicy.AppQosPolicy
conflicts
long
tmnxBsxAqpStatsConflict
s
The value of tmnxBsxAqpStatsConflicts
indicates the number of flows that have
hit this AQP entry, but resulted in a
conflict with the match criteria.
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-3
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
flows
long
tmnxBsxAqpStatsFlows
The value of tmnxBsxAqpStatsFlows
indicates the number of flows that have
hit this entry. In certain cases, a flow may
change its attributes thus undergoing a
second policy evaluation. In these cases,
the flow may be counted against two
different AQP entries.
BsxSapCustRecAppGrpStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxStatAaSubTable
Monitored class: service.AccessInterface
appGrpName
String
tmnxBsxStatAaName
The value of tmnxBsxStatAaName
specifies either the ISA-AA protocol,
application or app-group name for which
statistics are requested. The
tmnxBsxStatAaType is used to determine
the statistics type.
BsxSapStudyAppStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxStatAaSubSdyTable
Monitored class: service.AccessInterface
appName
String
tmnxBsxStatAaName
The value of tmnxBsxStatAaName
specifies either the ISA-AA protocol,
application or app-group name for which
statistics are requested. The
tmnxBsxStatAaType is used to determine
the statistics type.
(2 of 2)
Table E-3 aclfilter statistics
5620 SAM counter name
Type
MIB counter name
Description
HitCountStats
MIB table name: TIMETRA-FILTER-MIB.tIPFilterParamsTable
Monitored class: aclfilter.IpFilterEntry
egressHitByteCount
UINT128
tIPFilterParamsEgrHitByt
eCount
The value of
tIPFilterParamsEgrHitByteCount indicates
the number of bytes of all egress packets
that matched this entry.
egressHitCount
UINT128
tIPFilterParamsEgressHit
Count
This object indicates the number of times
an egress packet matched this entry.
ingressHitByteCount
UINT128
tIPFilterParamsIngrHitByt
eCount
The value of
tIPFilterParamsIngrHitByteCount
indicates the number of bytes of all
ingress packets that matched this entry.
ingressHitCount
UINT128
tIPFilterParamsIngressHit
Count
This object indicates the number of times
an ingress packet matched this entry.
MacHitCountStats
MIB table name: TIMETRA-FILTER-MIB.tMacFilterParamsTable
Monitored class: aclfilter.MacFilterEntry
(1 of 2)
E-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
egressHitByteCount
UINT128
tMacFilterParamsEgrHitB
yteCount
The value of
tMacFilterParamsEgrHitByteCount
indicates the number of bytes of all egress
packets that matched this entry.
egressHitCount
UINT128
tMacFilterParamsEgressHi
tCount
This object indicates the number of times
an egress packet matched this entry.
ingressHitByteCount
UINT128
tMacFilterParamsIngrHitB
yteCount
The value of
tMacFilterParamsIngrHitByteCount
indicates the number of bytes of all
ingress packets that matched this entry.
ingressHitCount
UINT128
tMacFilterParamsIngressH
itCount
This object indicates the number of times
an ingress packet matched this entry.
(2 of 2)
Table E-4 aps statistics
5620 SAM counter name
Type
MIB counter name
Description
ApsChannelStats
MIB table name: APS-MIB.apsChanStatusTable
Monitored class: aps.ApsChannel
discontinuityTime
long
apsChanStatusDiscontinui
tyTime
The value of sysUpTime on the most
recent occasion at which any one or more
of this channel's counters suffered a
discontinuity. The relevant counters are
the specific instances associated with this
channel of any Counter32 object
contained in apsChanStatusTable. If no
such discontinuities have occurred since
the last re-initialization of the local
management subsystem, then this object
contains a zero value.
lastSwitchover
long
apsChanStatusLastSwitch
over
When queried with index value
apsChanConfigNumber other than 0, this
object will return the value of sysUpTime
when this channel last completed a switch
to the protection line. If this channel has
never switched to the protection line, the
value 0 will be returned. When queried
with index value apsChanConfigNumber
set to 0, which is the protection line, this
object will return the value of sysUpTime
the last time that a working channel was
switched back to the working line from
this protection line. If no working channel
has ever switched back to the working
line from this protection line, the value 0
will be returned.
(1 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-5
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
signalDegrades
long
apsChanStatusSignalDegr
ades
A count of Signal Degrade conditions. This
condition occurs when the line Bit Error
Rate exceeds the currently configured
value of the relevant instance of
apsConfigSdBerThreshold. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of
apsChanStatusDiscontinuityTime.
signalFailures
long
apsChanStatusSignalFailu
res
A count of Signal Failure conditions that
have been detected on the incoming
signal. This condition occurs when a loss
of signal, loss of frame, AIS-L or a Line bit
error rate exceeding the currently
configured value of the relevant instance
of apsConfigSfBerThreshold.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
apsChanStatusDiscontinuityTime.
switchovers
long
apsChanStatusSwitchover
s
When queried with index value
apsChanConfigNumber other than 0, this
object will return the number of times
this channel has switched to the
protection line. When queried with index
value apsChanConfigNumber set to 0,
which is the protection line, this object
will return the number of times that any
working channel has been switched back
to the working line from this protection
line. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
apsChanStatusDiscontinuityTime.
switchoverSeconds
long
apsChanStatusSwitchover
Seconds
The cumulative Protection Switching
Duration (PSD) time in seconds. For a
working channel, this is the cumulative
number of seconds that service was
carried on the protection line. For the
protection line, this is the cumulative
number of seconds that the protection
line has been used to carry any working
channel traffic. This information is only
valid if revertive switching is enabled.
The value 0 will be returned otherwise.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
apsChanStatusDiscontinuityTime. For
example, if the value of an instance of
apsChanStatusSwitchoverSeconds
changes from a non-zero value to zero due
to revertive switching being disabled, it is
expected that the corresponding value of
apsChanStatusDiscontinuityTime will be
updated to reflect the time of the
configuration change.
(2 of 3)
E-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ApsGroupStats
MIB table name: APS-MIB.apsStatusTable
Monitored class: aps.ApsGroup
channelMismatches
long
apsStatusChannelMismatc
hes
A count of Channel Mismatch conditions.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
apsStatusDiscontinuityTime.
discontinuityTime
long
apsStatusDiscontinuityTi
me
The value of sysUpTime on the most
recent occasion at which any one or more
of this APS group's counters suffered a
discontinuity. The relevant counters are
the specific instances associated with this
APS group of any Counter32 object
contained in apsStatusTable. If no such
discontinuities have occurred since the
last re-initialization of the local
management subsystem, then this object
contains a zero value.
fEPLFs
long
apsStatusFEPLFs
A count of Far-End Protection-Line Failure
conditions. This condition is declared
based on receiving SF on the protection
line in the K1 byte. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of apsStatusDiscontinuityTime.
modeMismatches
long
apsStatusModeMismatche
s
A count of Mode Mismatch conditions.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
apsStatusDiscontinuityTime.
pSBFs
long
apsStatusPSBFs
A count of Protection Switch Byte Failure
conditions. This condition occurs when
either an inconsistent APS byte or an
invalid code is detected. An inconsistent
APS byte occurs when no three
consecutive K1 bytes of the last 12
successive frames are identical, starting
with the last frame containing a
previously consistent byte. An invalid
code occurs when the incoming K1 byte
contains an unused code or a code
irrelevant for the specific switching
operation (e.g., Reverse Request while no
switching request is outstanding) in three
consecutive frames. An invalid code also
occurs when the incoming K1 byte
contains an invalid channel number in
three consecutive frames. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of apsStatusDiscontinuityTime.
(3 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-7
E. 7450 ESS Release 7.0 statistics counters
Table E-5 bgp statistics
5620 SAM counter name
Type
MIB counter name
Description
PeerStats
MIB table name: TIMETRA-BGP-MIB.tBgpPeerNgOperTable
Monitored class: bgp.Peer
flaps
long
tBgpPeerNgOperFlaps
tBgpPeerNgOperFlaps indicates the
number of flaps of updates from this peer.
inputQueueMessages
long
tBgpPeerNgOperInputQue
ueMsgs
tBgpPeerNgOperInputQueueMsgs
indicates the number of unprocessed
messages in the queue, from this peer.
lastEvent
long
tBgpPeerNgOperLastEven
t
tBgpPeerNgOperLastEvent indicates the
last BGP event of this peer.
lastRestartTime
long
tBgpPeerNgOperLastRest
artTime
tBgpPeerNgOperLastRestartTime
indicates the last time the peer
attempted restart.
lastState
long
tBgpPeerNgOperLastState
tBgpPeerNgOperLastState indicates the
last BGP state of this peer.
mcastActivePrefixes
long
tBgpPeerNgOperMCastV4
ActivePfxs
The value of
tBgpPeerNgOperMCastV4ActivePfxs
indicates the number of active IPv4
multicast prefixes from this peer.
mcastPrefixesSuppressedByDampi
ng
long
tBgpPeerNgOperMCastV4
SuppPfxDamp
The value of
tBgpPeerNgOperMCastV4SuppPfxDamp
indicates the number of IPv4 multicast
prefixes from this peer, which have been
suppressed by damping.
mcastReceivedPrefixes
long
tBgpPeerNgOperMCastV4
RecvPfxs
The value of
tBgpPeerNgOperMCastV4RecvPfxs
indicates the number of IPv4 multicast
prefixes received from this peer.
mcastSentPrefixes
long
tBgpPeerNgOperMCastV4
SentPfxs
The value of
tBgpPeerNgOperMCastV4SentPfxs
indicates the number of IPv4 multicast
prefixes transmitted to this peer.
messageOctetsReceived
UINT128
tBgpPeerNgOperMsgOctet
sRcvd
tBgpPeerNgOperMsgOctetsRcvd indicates
the number of octets received from this
peer.
messageOctetsSent
UINT128
tBgpPeerNgOperMsgOctet
sSent
tBgpPeerNgOperMsgOctetsSent indicates
the number of octets transmitted to this
peer.
numberOfRestarts
long
tBgpPeerNgOperNumRest
arts
tBgpPeerNgOperNumRestarts indicates
the number of times the peer has
attempted restart.
outputQueueMessages
long
tBgpPeerNgOperOutputQ
ueueMsgs
tBgpPeerNgOperOutputQueueMsgs
indicates the number of untransmitted
messages in the queue, to this peer.
pathsReceived
long
tBgpPeerNgOperReceived
Paths
tBgpPeerNgOperReceivedPaths indicates
the number of paths received from this
peer.
prefixesActive
long
tBgpPeerNgOperActivePr
efixes
tBgpPeerNgOperActivePrefixes indicates
the number of active IPv4 prefixes from
this peer.
(1 of 3)
E-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
prefixesReceived
long
tBgpPeerNgOperReceived
Prefixes
tBgpPeerNgOperReceivedPrefixes
indicates the number of IPv4 prefixes
received from this peer.
prefixesSent
long
tBgpPeerNgOperSentPrefi
xes
tBgpPeerNgOperSentPrefixes indicates
the number of IPv4 prefixes transmitted
to this peer.
prefixesSuppressedByDamping
long
tBgpPeerNgOperV4SuppPf
xDamp
The value of
tBgpPeerNgOperV4SuppPfxDamp
indicates the number of IPv6 prefixes
from this peer, which have been
suppressed by damping.
v6ActivePrefixes
long
tBgpPeerNgOperV6Active
Prefixes
The value of
tBgpPeerNgOperV6ActivePrefixes
indicates the number of active IPv6
prefixes from this peer.
v6PrefixesSuppressedByDamping
long
tBgpPeerNgOperV6SuppPf
xDamp
The value of
tBgpPeerNgOperV6SuppPfxDamp
indicates the number of IPv6 prefixes
from this peer, which have been
suppressed by damping.
v6ReceivedPrefixes
long
tBgpPeerNgOperV6Receiv
edPrefixes
The value of
tBgpPeerNgOperV6ReceivedPrefixes
indicates the number of IPv6 prefixes
received from this peer.
v6SentPrefixes
long
tBgpPeerNgOperV6SentPr
efixes
The value of
tBgpPeerNgOperV6SentPrefixes indicates
the number of IPv6 prefixes transmitted
to this peer.
vpnActivePrefixes
long
tBgpPeerNgOperVpnActiv
ePrefixes
tBgpPeerNgOperVpnActivePrefixes
indicates the number of active VPN IPv4
prefixes from this BGP peer.
vpnPrefixesSuppressedByDamping
long
tBgpPeerNgOperVpnSupp
PfxDamp
The value of
tBgpPeerNgOperVpnSuppPfxDamp
indicates the number of VPN IPv4 prefixes
from this peer, which have been
suppressed by damping.
vpnReceivedPrefixes
long
tBgpPeerNgOperVpnRecv
Prefixes
tBgpPeerNgOperVpnRecvPrefixes
indicates the number of received VPN
IPv4 prefixes.
vpnSentPrefixes
long
tBgpPeerNgOperVpnSent
Prefixes
tBgpPeerNgOperVpnSentPrefixes
indicates the number of transmitted VPN
IPv4 prefixes.
PeerVprnIpv6Stats
MIB table name: TIMETRA-BGP-MIB.tBgpPeerNgOperTable
Monitored class: bgp.Peer
vpnIpv6ActivePfxs
long
tBgpPeerNgOperVpnIpv6A
ctivePfxs
The value of
tBgpPeerNgOperVpnIpv6ActivePfxs
indicates the number of active VPN IPv6
prefixes from this peer.
vpnIpv6RecvPfxs
long
tBgpPeerNgOperVpnIpv6R
ecvPfxs
The value of
tBgpPeerNgOperVpnIpv6RecvPfxs
indicates the number of VPN IPv6 prefixes
received from this peer.
(2 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-9
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vpnIpv6SentPfxs
long
tBgpPeerNgOperVpnIpv6S
entPfxs
The value of
tBgpPeerNgOperVpnIpv6SentPfxs
indicates the number of VPN IPv6 prefixes
transmitted to this peer.
vpnIpv6SuppPfxDamp
long
tBgpPeerNgOperVpnIpv6S
uppPfxDamp
The value of
tBgpPeerNgOperVpnIpv6SuppPfxDamp
indicates the number of VPN IPv6 prefixes
from this peer, which have been
suppressed by damping.
(3 of 3)
Table E-6 equipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AllocatedMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryPoolAllocated
Monitored class: equipment.SystemStatsHolder
allocatedMemory
long
sgiMemoryPoolAllocated
The value of sgiMemoryPoolAllocated
indicates the total memory currently
allocated in memory-pools on the system.
This memory may or may not be currently
in use, but is pre-allocated should the
software need to use it.
AvailableMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryAvailable
Monitored class: equipment.SystemStatsHolder
availableMemory
long
sgiMemoryAvailable
The value of sgiMemoryAvailable
indicates the amount of free memory in
the overall system that is not allocated to
memory pools, but is available in case a
memory pool needs to grow.
FibNextHopStats
MIB table name: TIMETRA-VRTR-MIB.vRtrFibStatNextHopTable
Monitored class: equipment.BaseCard
ipActive
long
vRtrFibStatNextHopIPActi
ve
vRtrFibStatNextHopIPActive indicates
current active IP next-hop counts for the
FIB on the IOM.
ipAvailable
long
vRtrFibStatNextHopIPAva
ilable
vRtrFibStatNextHopIPAvailable indicates
the available IP next-hop counts for the
FIB on the IOM.
tunnelActive
long
vRtrFibStatNextHopTunn
elActive
vRtrFibStatNextHopTunnelActive
indicates current active Tunnel next-hop
counts for the FIB on the IOM.
tunnelAvailable
long
vRtrFibStatNextHopTunn
elAvailable
vRtrFibStatNextHopTunnelAvailable
indicates the available Tunnel next-hop
counts for the FIB on the IOM.
FibStats
MIB table name: TIMETRA-VRTR-MIB.vRtrFibStatTable
Monitored class: equipment.BaseCard
(1 of 9)
E-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
aggrRoutes
long
vRtrFibStatAggrRoutes
vRtrFibStatAggrRoutes indicates current
aggregate route counts for the virtual
router.
alarmCount
long
vRtrFibStatAlarmCount
vRtrFibStatAlarmCount indicates the
number of times the FIB has raised an
alarm due to high FIB usage.
bgpRoutes
long
vRtrFibStatBGPRoutes
vRtrFibStatBGPRoutes indicates current
BGP route counts for the virtual router.
bgpVpnRoutes
long
vRtrFibStatBGPVpnRoutes
vRtrFibStatBGPVpnRoutes indicates
current BGP VPN route counts for the
virtual router.
directRoutes
long
vRtrFibStatDirectRoutes
vRtrFibStatDirectRoutes indicates current
direct route counts for the virtual router.
highUtilization
boolean
vRtrFibStatHighUtilizatio
n
vRtrFibStatHighUtilization indicates
whether or not the FIB on the IOM is
experiences persistent high occupancy.
hostRoutes
long
vRtrFibStatHostRoutes
vRtrFibStatHostRoutes indicates current
host route counts for the virtual router.
isisRoutes
long
vRtrFibStatISISRoutes
vRtrFibStatISISRoutes indicates current
ISIS route counts for the virtual router.
lastAlarmTime
long
vRtrFibStatLastAlarmTim
e
vRtrFibStatLastAlarmTime indicates the
last time a high FIB usage alarm was
raised.
managedRoutes
long
vRtrFibStatManagedRoute
s
vRtrFibStatManagedRoutes indicates
current managed route counts for the
virtual router.
ospfRoutes
long
vRtrFibStatOSPFRoutes
vRtrFibStatOSPFRoutes indicates current
OSPF route counts for the virtual router.
overflows
long
vRtrFibStatOverflows
vRtrFibStatOverflows indicates the
number of times the FIB has run out of
space.
ripRoutes
long
vRtrFibStatRIPRoutes
vRtrFibStatRIPRoutes indicates current
RIP route counts for the virtual router.
staticRoutes
long
vRtrFibStatStaticRoutes
vRtrFibStatStaticRoutes indicates current
static route counts for the virtual router.
subMgmtRoutes
long
vRtrFibStatSubMgmtRout
es
vRtrFibStatSubMgmtRoutes indicates
current Sub-management route counts for
the virtual router.
v6AggrRoutes
long
vRtrFibStatV6AggrRoutes
vRtrFibStatV6AggrRoutes indicates
current aggregate route counts for the
virtual router.
v6BGPRoutes
long
vRtrFibStatV6BGPRoutes
vRtrFibStatV6BGPRoutes indicates
current BGP route counts for the virtual
router.
v6BGPVpnRoutes
long
vRtrFibStatV6BGPVpnRou
tes
vRtrFibStatV6BGPVpnRoutes indicates
current BGP VPN route counts for the
virtual router.
v6DirectRoutes
long
vRtrFibStatV6DirectRoute
s
vRtrFibStatV6DirectRoutes indicates
current direct route counts for the virtual
router.
(2 of 9)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-11
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
v6HostRoutes
long
vRtrFibStatV6HostRoutes
vRtrFibStatV6HostRoutes indicates
current host route counts for the virtual
router.
v6ISISRoutes
long
vRtrFibStatV6ISISRoutes
vRtrFibStatV6ISISRoutes indicates current
ISIS route counts for the virtual router.
v6ManagedRoutes
long
vRtrFibStatV6ManagedRo
utes
vRtrFibStatV6ManagedRoutes indicates
current managed route counts for the
virtual router.
v6OSPFRoutes
long
vRtrFibStatV6OSPFRoutes
vRtrFibStatV6OSPFRoutes indicates
current OSPF route counts for the virtual
router.
v6RIPRoutes
long
vRtrFibStatV6RIPRoutes
vRtrFibStatV6RIPRoutes indicates current
RIP route counts for the virtual router.
v6StaticRoutes
long
vRtrFibStatV6StaticRoute
s
vRtrFibStatV6StaticRoutes indicates
current static route counts for the virtual
router.
v6SubMgmtRoutes
long
vRtrFibStatV6SubMgmtRo
utes
vRtrFibStatV6SubMgmtRoutes indicates
current Sub-management route counts for
the virtual router.
InterfaceAdditionalStats
MIB table name: IF-MIB.ifXTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
receivedBroadcastPackets
UINT128
ifHCInBroadcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a broadcast address at
this sub-layer. This object is a 64-bit
version of ifInBroadcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedMulticastPackets
UINT128
ifHCInMulticastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a multicast address at
this sub-layer. For a MAC layer protocol,
this includes both Group and Functional
addresses. This object is a 64-bit version
of ifInMulticastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedTotalOctets
UINT128
ifHCInOctets
The total number of octets received on
the interface, including framing
characters. This object is a 64-bit version
of ifInOctets. Discontinuities in the value
of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
(3 of 9)
E-12
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedUnicastPackets
UINT128
ifHCInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer. This
object is a 64-bit version of ifInUcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
transmittedBroadcastPackets
UINT128
ifHCOutBroadcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a broadcast address at this sub-layer,
including those that were discarded or not
sent. This object is a 64-bit version of
ifOutBroadcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedMulticastPackets
UINT128
ifHCOutMulticastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a multicast address at this sub-layer,
including those that were discarded or not
sent. For a MAC layer protocol, this
includes both Group and Functional
addresses. This object is a 64-bit version
of ifOutMulticastPkts. Discontinuities in
the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedTotalOctets
UINT128
ifHCOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. This object is a 64-bit version
of ifOutOctets. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedUnicastPackets
UINT128
ifHCOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent. This
object is a 64-bit version of
ifOutUcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
(4 of 9)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-13
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
InterfaceStats
MIB table name: IF-MIB.ifTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
outboundBadPackets
long
ifOutErrors
For packet-oriented interfaces, the
number of outbound packets that could
not be transmitted because of errors. For
character-oriented or fixed-length
interfaces, the number of outbound
transmission units that could not be
transmitted because of errors.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
outboundPacketsDiscarded
long
ifOutDiscards
The number of outbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being transmitted. One possible
reason for discarding such a packet could
be to free up buffer space. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedBadPackets
long
ifInErrors
For packet-oriented interfaces, the
number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol. For character- oriented or
fixed-length interfaces, the number of
inbound transmission units that contained
errors preventing them from being
deliverable to a higher-layer protocol.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedOctets
long
ifInOctets
The total number of octets received on
the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
(5 of 9)
E-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedPacketsDiscarded
long
ifInDiscards
The number of inbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being deliverable to a higher-layer
protocol. One possible reason for
discarding such a packet could be to free
up buffer space. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedUnicastPackets
long
ifInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedUnknownProtocolPackets
long
ifInUnknownProtos
For packet-oriented interfaces, the
number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
For character-oriented or fixed-length
interfaces that support protocol
multiplexing the number of transmission
units received via the interface which
were discarded because of an unknown or
unsupported protocol. For any interface
that does not support protocol
multiplexing, this counter will always be
0. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedOctets
long
ifOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedUnicastPackets
long
ifOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
MediaIndependentStats
MIB table name: HC-RMON-MIB.mediaIndependentTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
(6 of 9)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-15
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dropEvents
long
mediaIndependentDropEv
ents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
droppedFrames
long
mediaIndependentDropp
edFrames
The total number of frames which were
received by the probe and therefore not
accounted for in the
mediaIndependentDropEvents, but for
which the probe chose not to count for
this entry for whatever reason. Most
often, this event occurs when the probe is
out of some resources and decides to shed
load from this collection. This count does
not include packets that were not
counted because they had MAC-layer
errors. Note that, unlike the dropEvents
counter, this number is the exact number
of frames dropped.
duplex
int
mediaIndependentDuplex
Mode
The current mode of this link. Note that if
the link has full-duplex capabilities but is
operating in half-duplex mode, this value
will be halfduplex(1).
duplexChanges
long
mediaIndependentDuplex
Changes
The number of times this link has changed
from full-duplex mode to half-duplex
mode or from half-duplex mode to
full-duplex mode.
inputSpeed
long
mediaIndependentInputS
peed
The nominal maximum speed in kilobits
per second of this half-duplex link or on
the inbound connection of this full-duplex
link. If the speed is unknown or there is no
fixed maximum (e.g. a compressed link),
this value shall be zero.
outputSpeed
long
mediaIndependentOutput
Speed
The nominal maximum speed in kilobits
per second of this full-duplex link in the
direction of the network. If the speed is
unknown, the link is half-duplex, or there
is no fixed maximum (e.g. a compressed
link), this value shall be zero.
receivedBadPackets
long
mediaIndependentInError
s
The total number of bad packets received
on a half-duplex link or on the inbound
connection of a full-duplex link.
receivedNonUnicastPackets
UINT128
mediaIndependentInNUC
astHighCapacityPkts
The total number of non-unicast packets
(including bad packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
receivedOctets
UINT128
mediaIndependentInHigh
CapacityOctets
The total number of octets of data
(including those in bad packets) received
(excluding framing bits but including FCS
octets) on a half-duplex link or on the
inbound connection of a full-duplex link.
receivedPackets
UINT128
mediaIndependentInHigh
CapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
(7 of 9)
E-16
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmittedBadPackets
long
mediaIndependentOutErr
ors
The total number of bad packets received
on a full-duplex link in the direction of the
network.
transmittedNonUnicastPackets
UINT128
mediaIndependentOutNU
CastHighCapacityPkts
The total number of packets (including
bad packets) received on a full-duplex
link in the direction of the network.
transmittedOctets
UINT128
mediaIndependentOutHig
hCapacityOctets
The total number of octets of data
(including those in bad packets) received
on a full-duplex link in the direction of the
network (excluding framing bits but
including FCS octets).
transmittedPackets
UINT128
mediaIndependentOutHig
hCapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
full-duplex link in the direction of the
network.
PortNetEgressStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortNetEgressStatsTable
Monitored class: equipment.PhysicalPort
inProfileOctetsDropped
UINT128
tmnxPortNetEgressDroInP
rofOcts
tmnxPortNetEgressDroInProfOcts
indicates the number of conforming
network egress octets dropped on this
port using this queue.
inProfileOctetsForwarded
UINT128
tmnxPortNetEgressFwdIn
ProfOcts
tmnxPortNetEgressFwdInProfOcts
indicates the number of conforming
network egress octets forwarded on this
port using this queue.
inProfilePacketsDropped
UINT128
tmnxPortNetEgressDroInP
rofPkts
tmnxPortNetEgressDroInProfPkts
indicates the number of conforming
network egress packets dropped on this
port using this queue.
inProfilePacketsForwarded
UINT128
tmnxPortNetEgressFwdIn
ProfPkts
tmnxPortNetEgressFwdInProfPkts
indicates the number of conforming
network egress packets forwarded on this
port using this queue.
outOfProfileOctetsDropped
UINT128
tmnxPortNetEgressDroOu
tProfOcts
tmnxPortNetEgressDroOutProfOcts
indicates the number of exceeding
network egress octets dropped on this
port using this queue.
outOfProfileOctetsForwarded
UINT128
tmnxPortNetEgressFwdO
utProfOcts
tmnxPortNetEgressFwdOutProfOcts
indicates the number of exceeding
network egress octets forwarded on this
port using this queue.
outOfProfilePacketsDropped
UINT128
tmnxPortNetEgressDroOu
tProfPkts
tmnxPortNetEgressDroOutProfPkts
indicates the number of exceeding
network egress packets dropped on this
port using this queue.
outOfProfilePacketsForwarded
UINT128
tmnxPortNetEgressFwdO
utProfPkts
tmnxPortNetEgressFwdOutProfPkts
indicates the number of exceeding
network egress packets forwarded on this
port using this queue.
(8 of 9)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-17
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
queueId
long
tmnxPortNetEgressQueue
Index
tmnxPortNetEgressQueueIndex serves as
the tertiary index. When used in
conjunction with tmnxChassisIndex and
tmnxPortPortID, it uniquely identifies a
network egress queue for the specified
port in the managed system.
PortNetIngressStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortNetIngressStatsTable
Monitored class: equipment.PhysicalPort
inProfileOctetsDropped
UINT128
tmnxPortNetIngressDroIn
ProfOcts
tmnxPortNetIngressDroInProfOcts
indicates the number of conforming
network ingress octets dropped on this
port using this queue.
inProfileOctetsForwarded
UINT128
tmnxPortNetIngressFwdIn
ProfOcts
tmnxPortNetIngressFwdInProfOcts
indicates the number of conforming
network ingress octets forwarded on this
port using this queue.
inProfilePacketsDropped
UINT128
tmnxPortNetIngressDroIn
ProfPkts
tmnxPortNetIngressDroInProfPkts
indicates the number of conforming
network ingress packets dropped on this
port using this queue.
inProfilePacketsForwarded
UINT128
tmnxPortNetIngressFwdIn
ProfPkts
tmnxPortNetIngressFwdInProfPkts
indicates the number of conforming
network ingress packets forwarded on this
port using this queue.
outOfProfileOctetsDropped
UINT128
tmnxPortNetIngressDroO
utProfOcts
tmnxPortNetIngressDroOutProfOcts
indicates the number of exceeding
network ingress octets dropped on this
port using this queue.
outOfProfileOctetsForwarded
UINT128
tmnxPortNetIngressFwdO
utProfOcts
tmnxPortNetIngressFwdOutProfOcts
indicates the number of exceeding
network ingress octets forwarded on this
port using this queue.
outOfProfilePacketsDropped
UINT128
tmnxPortNetIngressDroO
utProfPkts
tmnxPortNetIngressDroOutProfPkts
indicates the number of exceeding
network ingress packets dropped on this
port using this queue.
outOfProfilePacketsForwarded
UINT128
tmnxPortNetIngressFwdO
utProfPkts
tmnxPortNetIngressFwdOutProfPkts
indicates the number of exceeding
network ingress packets forwarded on this
port using this queue.
SystemCpuStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiCpuUsage
Monitored class: equipment.SystemStatsHolder
systemCpuUsage
long
sgiCpuUsage
The value of sgiCpuUsage indicates the
current CPU utilization for the system.
SystemMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryUsed
Monitored class: equipment.SystemStatsHolder
systemMemoryUsage
long
sgiMemoryUsed
The value of sgiMemoryUsed indicates the
total pre-allocated pool memory
currently in use on the system.
(9 of 9)
E-18
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
Table E-7 ethernetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AdditionalEthernetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortEtherTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
highCapacityPackets1519toMaxFra
meSize
UINT128
tmnxPortEtherHCPkts151
9toMax
The total number of packets (including
bad packets) received that were between
1519 octets in length and the maximum
frame size, usually 12287 octets inclusive
(excluding framing bits but including FCS
octets). The lower 32-bits of this 64-bit
counter will equal the value of
tmnxPortEtherHCPkts1519toMax. The
high 32-bits of this counter will equal the
value of
tmnxPortEtherHCOverPkts1519toMax.
packets1519toMaxFrameSize
long
tmnxPortEtherPkts1519to
Max
The total number of packets received that
were longer than 1518 octets but less than
the maximum frame size for the
particular medium, usually 12287 octets
(excluding framing bits, but including FCS
octets) and were otherwise well formed.
dot3StatsAlignmentErrors
A count of frames received on a particular
interface that are not an integral number
of octets in length and do not pass the FCS
check. The count represented by an
instance of this object is incremented
when the alignmentError status is
returned by the MAC service to the LLC (or
other MAC user). Received frames for
which multiple error conditions pertain
are, according to the conventions of IEEE
802.3 Layer Management, counted
exclusively according to the error status
presented to the LLC. This counter does
not increment for group encoding
schemes greater than 4 bits per group. For
interfaces operating at 10 Gb/s, this
counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsAlignmentErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.1.1.7,
aAlignmentErrors.
Dot3Stats
MIB table name: EtherLike-MIB.dot3StatsTable
Monitored class: equipment.PhysicalPort
alignmentErrors
long
(1 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-19
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
carrierSenseErrors
long
dot3StatsCarrierSenseErr
ors
The number of times that the carrier
sense condition was lost or never asserted
when attempting to transmit a frame on a
particular interface. The count
represented by an instance of this object
is incremented at most once per
transmission attempt, even if the carrier
sense condition fluctuates during a
transmission attempt. This counter does
not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.13,
aCarrierSenseErrors.
deferredTransmissions
long
dot3StatsDeferredTransm
issions
A count of frames for which the first
transmission attempt on a particular
interface is delayed because the medium
is busy. The count represented by an
instance of this object does not include
frames involved in collisions. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.9,
aFramesWithDeferredXmissions.
duplex
int
dot3StatsDuplexStatus
The current mode of operation of the MAC
entity. 'unknown' indicates that the
current duplex mode could not be
determined. Management control of the
duplex mode is accomplished through the
MAU MIB. When an interface does not
support autonegotiation, or when
autonegotiation is not enabled, the
duplex mode is controlled using
ifMauDefaultType. When autonegotiation
is supported and enabled, duplex mode is
controlled using
ifMauAutoNegAdvertisedBits. In either
case, the currently operating duplex
mode is reflected both in this object and
in ifMauType. Note that this object
provides redundant information with
ifMauType. Normally, redundant objects
are discouraged. However, in this
instance, it allows a management
application to determine the duplex
status of an interface without having to
know every possible value of ifMauType.
This was felt to be sufficiently valuable to
justify the redundancy. REFERENCE [IEEE
802.3 Std.], 30.3.1.1.32, aDuplexStatus.
(2 of 20)
E-20
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
excessiveCollisions
long
dot3StatsExcessiveCollisi
ons
A count of frames for which transmission
on a particular interface fails due to
excessive collisions. This counter does not
increment when the interface is operating
in full-duplex mode. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.11,
aFramesAbortedDueToXSColls.
fcsErrors
long
dot3StatsFCSErrors
A count of frames received on a particular
interface that are an integral number of
octets in length but do not pass the FCS
check. This count does not include frames
received with frame-too-long or
frame-too-short error. The count
represented by an instance of this object
is incremented when the
frameCheckError status is returned by the
MAC service to the LLC (or other MAC
user). Received frames for which multiple
error conditions pertain are, according to
the conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. Note: Coding errors detected by
the physical layer for speeds above 10
Mb/s will cause the frame to fail the FCS
check. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 5 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the dot3HCStatsFCSErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.6,
aFrameCheckSequenceErrors.
(3 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-21
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
frameTooLongs
long
dot3StatsFrameTooLongs
A count of frames received on a particular
interface that exceed the maximum
permitted frame size. The count
represented by an instance of this object
is incremented when the frameTooLong
status is returned by the MAC service to
the LLC (or other MAC user). Received
frames for which multiple error
conditions pertain are, according to the
conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 80 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsFrameTooLongs object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.25, aFrameTooLongErrors.
internalMacReceiveErrors
long
dot3StatsInternalMacRec
eiveErrors
A count of frames for which reception on
a particular interface fails due to an
internal MAC sublayer receive error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsFrameTooLongs object, the
dot3StatsAlignmentErrors object, or the
dot3StatsFCSErrors object. The precise
meaning of the count represented by an
instance of this object is implementationspecific. In particular, an instance of this
object may represent a count of receive
errors on a particular interface that are
not otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacReceiveErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.15,
aFramesLostDueToIntMACRcvError.
(4 of 20)
E-22
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
internalMacTransmitErrors
long
dot3StatsInternalMacTran
smitErrors
A count of frames for which transmission
on a particular interface fails due to an
internal MAC sublayer transmit error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsLateCollisions object, the
dot3StatsExcessiveCollisions object, or
the dot3StatsCarrierSenseErrors object.
The precise meaning of the count
represented by an instance of this object
is implementation- specific. In particular,
an instance of this object may represent a
count of transmission errors on a
particular interface that are not
otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacTransmitErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.12,
aFramesLostDueToIntMACXmitError.
lateCollisions
long
dot3StatsLateCollisions
The number of times that a collision is
detected on a particular interface later
than one slotTime into the transmission of
a packet. A (late) collision included in a
count represented by an instance of this
object is also considered as a (generic)
collision for purposes of other
collision-related statistics. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.10,
aLateCollisions.
(5 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-23
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
multipleCollisionFrames
long
dot3StatsMultipleCollisio
nFrames
A count of frames that are involved in
more than one collision and are
subsequently transmitted successfully. A
frame that is counted by an instance of
this object is also counted by the
corresponding instance of either the
ifOutUcastPkts, ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsSingleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.4,
aMultipleCollisionFrames.
singleCollisionFrames
long
dot3StatsSingleCollisionF
rames
A count of frames that are involved in a
single collision, and are subsequently
transmitted successfully. A frame that is
counted by an instance of this object is
also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsMultipleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.3,
aSingleCollisionFrames.
sqeTestErrors
long
dot3StatsSQETestErrors
A count of times that the SQE TEST ERROR
is received on a particular interface. The
SQE TEST ERROR is set in accordance with
the rules for verification of the SQE
detection mechanism in the PLS Carrier
Sense Function as described in IEEE Std.
802.3, 2000 Edition, section 7.2.4.6. This
counter does not increment on interfaces
operating at speeds greater than 10 Mb/s,
or on interfaces operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 7.2.4.6, also
30.3.2.1.4, aSQETestErrors.
(6 of 20)
E-24
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
symbolErrors
long
dot3StatsSymbolErrors
For an interface operating at 100 Mb/s,
the number of times there was an invalid
data symbol when a valid carrier was
present. For an interface operating in
half-duplex mode at 1000 Mb/s, the
number of times the receiving media is
non-idle (a carrier event) for a period of
time equal to or greater than slotTime,
and during which there was at least one
occurrence of an event that causes the
PHY to indicate 'Data reception error' or
'carrier extend error' on the GMII. For an
interface operating in full-duplex mode at
1000 Mb/s, the number of times the
receiving media is non-idle (a carrier
event) for a period of time equal to or
greater than minFrameSize, and during
which there was at least one occurrence
of an event that causes the PHY to
indicate 'Data reception error' on the
GMII. For an interface operating at 10
Gb/s, the number of times the receiving
media is non-idle (a carrier event) for a
period of time equal to or greater than
minFrameSize, and during which there
was at least one occurrence of an event
that causes the PHY to indicate 'Receive
Error' on the XGMII. The count
represented by an instance of this object
is incremented at most once per carrier
event, even if multiple symbol errors
occur during the carrier event. This count
does not increment if a collision is
present. This counter does not increment
when the interface is operating at 10
Mb/s. For interfaces operating at 10 Gb/s,
this counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsSymbolErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.2.1.5,
aSymbolErrorDuringCarrier.
EthernetHighCapacityStats
MIB table name: HC-RMON-MIB.etherStatsHighCapacityTable
Monitored classes:
• equipment.PhysicalPort
• equipment.ManagementPort
packets1024to1518Octets
UINT128
etherStatsHighCapacityPk
ts1024to1518Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
(7 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-25
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
packets128to255Octets
UINT128
etherStatsHighCapacityPk
ts128to255Octets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
UINT128
etherStatsHighCapacityPk
ts256to511Octets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
UINT128
etherStatsHighCapacityPk
ts512to1023Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
UINT128
etherStatsHighCapacityPk
ts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
UINT128
etherStatsHighCapacityPk
ts65to127Octets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(8 of 20)
E-26
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
UINT128
etherStatsHighCapacityO
ctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). If the network
is half-duplex Fast Ethernet, this object
can be used as a reasonable estimate of
utilization. If greater precision is desired,
the etherStatsHighCapacityPkts and
etherStatsHighCapacityOctets objects
should be sampled before and after a
common interval. The differences in the
sampled values are Pkts and Octets,
respectively, and the number of seconds
in the interval is Interval. These values
are used to calculate the Utilization as
follows: Pkts * (.96 + .64) + (Octets * .08)
Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent. This table is not
appropriate for monitoring full-duplex
ethernets. If the network is a full-duplex
ethernet and the mediaIndependentTable
is monitoring that network, the utilization
can be calculated as follows: 1)
Determine the utilization of the inbound
path by using the appropriate equation
(for ethernet or fast ethernet) to
determine the utilization, substituting
mediaIndependentInPkts for
etherStatsHighCapacityPkts, and
mediaIndependentInOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization inUtilization. 2)
Determine the utilization of the outbound
path by using the same equation to
determine the utilization, substituting
mediaIndependentOutPkts for
etherStatsHighCapacityPkts, and
mediaIndependentOutOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization outUtilization. 3) The
utilization is the maximum of inUtilization
and outUtilization. This metric shows the
amount of percentage of bandwidth that
is left before congestion will be
experienced on the link.
totalPackets
UINT128
etherStatsHighCapacityPk
ts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
etherStatsBroadcastPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
EthernetStats
MIB table name: RMON-MIB.etherStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
broadcastPackets
long
(9 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-27
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
etherStatsCollisions
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the
location of the RMON probe. Section
8.2.1.3 (10BASE-5) and section 10.3.1.3
(10BASE-2) of IEEE standard 802.3 states
that a station must detect a collision, in
the receive mode, if three or more
stations are transmitting simultaneously.
A repeater port must detect a collision
when two or more stations are
transmitting simultaneously. Thus a probe
placed on a repeater port could record
more collisions than a probe connected to
a station on the same segment would.
Probe location plays a much smaller role
when considering 10BASE-T. 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments
to which the repeater is connected.
crcAlignErrors
long
etherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
etherStatsDropEvents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
etherStatsFragments
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(10 of 20)
E-28
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
etherStatsJabbers
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different than the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
where any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPackets
long
etherStatsMulticastPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
oversizePackets
long
etherStatsOversizePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
packets1024to1518Octets
long
etherStatsPkts1024to151
8Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets128to255Octets
long
etherStatsPkts128to255O
ctets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
long
etherStatsPkts256to511O
ctets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
long
etherStatsPkts512to1023
Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
long
etherStatsPkts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
long
etherStatsPkts65to127Oc
tets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(11 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-29
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
long
etherStatsOctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
10-Megabit ethernet utilization. If greater
precision is desired, the etherStatsPkts
and etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent.
totalPackets
long
etherStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
undersizePackets
long
etherStatsUndersizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
OtuIfStats
MIB table name: TIMETRA-OTU-MIB.tmnxOtuIfRawStatsTable
Monitored class: equipment.PhysicalPort
fecCorrOnes
long
tmnxOtuIfRawStatsFECCo
rrOnes
The value of
tmnxOtuIfRawStatsFECCorrOnes indicates
the number of Forward Error Correction
(FEC) corrected ones.
fecCorrZeros
long
tmnxOtuIfRawStatsFECCo
rrZeros
The value of
tmnxOtuIfRawStatsFECCorrZeros
indicates the number of Forward Error
Correction (FEC) corrected zeros.
fecSes
long
tmnxOtuIfRawStatsFECSE
S
The value of tmnxOtuIfRawStatsFECSES
indicates the number of Forward Error
Correction (FEC) Severely Errors Seconds
(SES).
fecUncorrSr
long
tmnxOtuIfRawStatsFECUn
corrSR
The value of
tmnxOtuIfRawStatsFECUncorrSR indicates
the number of Forward Error Correction
(FEC) Uncorrectable Sub-Rows.
hcFecCorrOnes
UINT128
tmnxOtuIfRawStatsHCFEC
CorrOnes
The value of
tmnxOtuIfRawStatsFECCorrOnes indicates
the High Capacity number of Forward
Error Correction (FEC) corrected ones.
hcFecCorrZeros
UINT128
tmnxOtuIfRawStatsHCFEC
CorrZeros
The value of
tmnxOtuIfRawStatsHCFECCorrZeros
indicates the High Capacity number of
Forward Error Correction (FEC) corrected
zeros.
(12 of 20)
E-30
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
hcFecUncorrSr
UINT128
tmnxOtuIfRawStatsHCFEC
UncorrSR
The value of
tmnxOtuIfRawStatsHCFECUncorrSR
indicates the High Capacity number of
Forward Error Correction (FEC)
Uncorrectable Sub-Rows.
hcPmBei
UINT128
tmnxOtuIfRawStatsHCPM
BEI
The value of tmnxOtuIfRawStatsPMBEI
indicates the High Capacity number of
Path Monitoring (PM) Backward Error
Indication (BEI) errors.
hcPmBip8
UINT128
tmnxOtuIfRawStatsHCPM
BIP8
The value of
tmnxOtuIfRawStatsHCPMBIP8 indicates
the High Capacity number of Path
Monitoring (PM) BIP8 errors.
hcSmBei
UINT128
tmnxOtuIfRawStatsHCSM
BEI
The value of tmnxOtuIfRawStatsHCSMBEI
indicates the High Capacity number of
Section Monitoring (SM) Backward Error
Indication (BEI) errors.
hcSmBip8
UINT128
tmnxOtuIfRawStatsHCSM
BIP8
The value of tmnxOtuIfRawStatsHCSMBIP8
indicates the High Capacity number of
Section Monitoring (SM) BIP8 errors.
ofFecCorrOnes
long
tmnxOtuIfRawStatsOFFEC
CorrOnes
The value of
tmnxOtuIfRawStatsFECCorrOnes indicates
the number of times the
tmnxOtuIfRawStatsFECCorrOnes
overflowed.
ofFecCorrZeros
long
tmnxOtuIfRawStatsOFFEC
CorrZeros
The value of
tmnxOtuIfRawStatsOFFECCorrZeros
indicates the number of times the
tmnxOtuIfRawStatsFECCorrZeros
overflowed.
ofFecUncorrSr
long
tmnxOtuIfRawStatsOFFEC
UncorrSR
The value of
tmnxOtuIfRawStatsOFFECUncorrSR
indicates the number of times the
tmnxOtuIfRawStatsFECUncorrSR
overflowed.
ofPmBei
long
tmnxOtuIfRawStatsOFPM
BEI
The value of tmnxOtuIfRawStatsOFPMBEI
indicates the number of times
tmnxOtuIfRawStatsPMBEI overflowed.
ofPmBip8
long
tmnxOtuIfRawStatsOFPM
BIP8
The value of tmnxOtuIfRawStatsOFPMBIP8
indicates the number of times the
tmnxOtuIfRawStatsPMBIP8 overflowed.
ofSmBei
long
tmnxOtuIfRawStatsOFSMB
EI
The value of tmnxOtuIfRawStatsOFSMBEI
indicates the number of times the
tmnxOtuIfRawStatsSMBEI overflowed.
ofSmBip8
long
tmnxOtuIfRawStatsOFSMB
IP8
The value of tmnxOtuIfRawStatsOFSMBIP8
indicates the number of times the
tmnxOtuIfRawStatsSMBIP8 overflowed.
pmBei
long
tmnxOtuIfRawStatsPMBEI
The value of tmnxOtuIfRawStatsPMBEI
indicates the number of Path Monitoring
(PM) Backward Error Indication (BEI)
errors.
pmBip8
long
tmnxOtuIfRawStatsPMBIP
8
The value of tmnxOtuIfRawStatsPMBIP8
indicates the number of Path Monitoring
(PM) BIP8 errors.
(13 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-31
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
pmSes
long
tmnxOtuIfRawStatsPMSES
The value of tmnxOtuIfRawStatsPMSES
indicates the number of Path Monitoring
(PM) Severely Errored Seconds (SES).
smBei
long
tmnxOtuIfRawStatsSMBEI
The value of tmnxOtuIfRawStatsSMBEI
indicates the number of Section
Monitoring (SM) Backward Error Indication
(BEI) errors.
smBip8
long
tmnxOtuIfRawStatsSMBIP
8
The value of tmnxOtuIfRawStatsSMBIP8
indicates the number of Section
Monitoring (SM) BIP8 errors.
smSes
long
tmnxOtuIfRawStatsSMSES
The value of tmnxOtuIfRawStatsSMSES
indicates the number of Section
Monitoring (SM) Severely Errored Seconds
(SES).
PortEgrQosQueueStat
MIB table name: TIMETRA-PORT-MIB.tmnxPortEgrQosQStatTable
Monitored class: ethernetequipment.AccessEgrQGroup
portEgrQosQStatDpdInProfOcts
UINT128
tmnxPortEgrQosQStatDpd
InProfOcts
The value of
tmnxPortEgrQosQStatDpdInProfOcts
indicates the number of in-profile octets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
portEgrQosQStatDpdInProfPkts
UINT128
tmnxPortEgrQosQStatDpd
InProfPkts
The value of
tmnxPortEgrQosQStatDpdInProfPkts
indicates the number of in-profile packets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
portEgrQosQStatDpdOutProfOcts
UINT128
tmnxPortEgrQosQStatDpd
OutProfOcts
The value of
tmnxPortEgrQosQStatDpdOutProfOcts
indicates the number of out-of-profile
octets discarded by the egress Qchip due
to: MBS exceeded, buffer pool limit
exceeded, etc.
portEgrQosQStatDpdOutProfPkts
UINT128
tmnxPortEgrQosQStatDpd
OutProfPkts
The value of
tmnxPortEgrQosQStatDpdOutProfPkts
indicates the number of out-of-profile
packets discarded by the egress Qchip due
to: MBS exceeded, buffer pool limit
exceeded, etc.
portEgrQosQStatFwdInProfOcts
UINT128
tmnxPortEgrQosQStatFwd
InProfOcts
The value of
tmnxPortEgrQosQStatFwdInProfOcts
indicates the number of in-profile octets
(rate below CIR) forwarded by the egress
Qchip.
portEgrQosQStatFwdInProfPkts
UINT128
tmnxPortEgrQosQStatFwd
InProfPkts
The value of
tmnxPortEgrQosQStatFwdInProfPkts
indicates the number of in-profile packets
(rate below CIR) forwarded by the egress
Qchip.
portEgrQosQStatFwdOutProfOcts
UINT128
tmnxPortEgrQosQStatFwd
OutProfOcts
The value of
tmnxPortEgrQosQStatFwdOutProfOcts
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
egress Qchip.
(14 of 20)
E-32
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portEgrQosQStatFwdOutProfPkts
UINT128
tmnxPortEgrQosQStatFwd
OutProfPkts
The value of
tmnxPortEgrQosQStatFwdOutProfPkts
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
egress Qchip.
portEgrQosQStatQueueId
long
tmnxPortEgrQosQStatQue
ueId
The value of
tmnxPortEgrQosQStatQueueId specifies
the queue-group queue ID which is used as
the fourth index to the table entry.
PortIngQosQueueStat
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngQosQStatTable
Monitored class: ethernetequipment.AccessIngrQGroup
portIngQosQStatDpdHiPrioOcts
UINT128
tmnxPortIngQosQStatDpd
HiPrioOcts
The value of
tmnxPortIngQosQStatDpdHiPrioOcts
indicates the number of high priority
octets, as determined by the port ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
portIngQosQStatDpdHiPrioPkts
UINT128
tmnxPortIngQosQStatDpd
HiPrioPkts
The value of
tmnxPortIngQosQStatDpdHiPrioPkts
indicates the number of high priority
packets, as determined by the port
ingress QoS policy, dropped by the Qchip
due to: MBS exceeded, buffer pool limit
exceeded, etc.
portIngQosQStatDpdLoPrioOcts
UINT128
tmnxPortIngQosQStatDpd
LoPrioOcts
The value of
tmnxPortIngQosQStatDpdLoPrioOcts
indicates the number of low priority
octets, as determined by the port ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
portIngQosQStatDpdLoPrioPkts
UINT128
tmnxPortIngQosQStatDpd
LoPrioPkts
The value of
tmnxPortIngQosQStatDpdLoPrioPkts
indicates the number of low priority
packets, as determined by the port
ingress QoS policy, dropped by the Qchip
due to: MBS exceeded, buffer pool limit
exceeded, etc.
portIngQosQStatFwdInProfOcts
UINT128
tmnxPortIngQosQStatFwd
InProfOcts
The value of
tmnxPortIngQosQStatFwdInProfOcts
indicates the number of in-profile octets
(rate below CIR) forwarded by the ingress
Qchip.
portIngQosQStatFwdInProfPkts
UINT128
tmnxPortIngQosQStatFwd
InProfPkts
The value of
tmnxPortIngQosQStatFwdInProfPkts
indicates the number of in-profile packets
(rate below CIR) forwarded by the ingress
Qchip.
portIngQosQStatFwdOutProfOcts
UINT128
tmnxPortIngQosQStatFwd
OutProfOcts
The value of
tmnxPortIngQosQStatFwdOutProfOcts
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
ingress Qchip.
(15 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-33
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portIngQosQStatFwdOutProfPkts
UINT128
tmnxPortIngQosQStatFwd
OutProfPkts
The value of
tmnxPortIngQosQStatFwdOutProfPkts
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
ingress Qchip.
portIngQosQStatOffHiPrioOcts
UINT128
tmnxPortIngQosQStatOff
HiPrioOcts
The value of
tmnxPortIngQosQStatOffHiPrioOcts
indicates the number of high priority
octets, as determined by the port ingress
QoS policy, offered by the Pchip to the
Qchip.
portIngQosQStatOffHiPrioPkts
UINT128
tmnxPortIngQosQStatOff
HiPrioPkts
The value of
tmnxPortIngQosQStatOffHiPrioPkts
indicates the number of high priority
packets, as determined by the port
ingress QoS policy, offered by the Pchip to
the Qchip.
portIngQosQStatOffLoPrioOcts
UINT128
tmnxPortIngQosQStatOffL
oPrioOcts
The value of
tmnxPortIngQosQStatOffLoPrioOcts
indicates the number of low priority
octets, as determined by the port ingress
QoS policy, offered by the Pchip to the
Qchip.
portIngQosQStatOffLoPrioPkts
UINT128
tmnxPortIngQosQStatOffL
oPrioPkts
The value of
tmnxPortIngQosQStatOffLoPrioPkts
indicates the number of low priority
packets, as determined by the port
ingress QoS policy, offered by the Pchip to
the Qchip.
portIngQosQStatQueueId
long
tmnxPortIngQosQStatQue
ueId
The value of
tmnxPortIngQosQStatQueueId specifies
the queue-group queue ID which is used as
the fourth index to the table entry.
portIngQosQStatUncolOctsOff
UINT128
tmnxPortIngQosQStatUnc
olOctsOff
The value of
tmnxPortIngQosQStatUncolOctsOff
indicates the number of uncolored octets
offered to the ingress Qchip.
portIngQosQStatUncolPktsOff
UINT128
tmnxPortIngQosQStatUnc
olPktsOff
The value of
tmnxPortIngQosQStatUncolPktsOff
indicates the number of uncolored
packets offered to the ingress Qchip.
PortNetEgrQueueStat
MIB table name: TIMETRA-PORT-MIB.tmnxPortNetEgrQStatTable
Monitored class: ethernetequipment.NetworkEgrQGroup
portNetEgrQDroInProfOcts
UINT128
tmnxPortNetEgrQDroInPr
ofOcts
The value of
tmnxPortNetEgrQDroInProfOcts indicates
the number of conforming network egress
octets dropped on this port using this
queue-group queue.
portNetEgrQDroInProfPkts
UINT128
tmnxPortNetEgrQDroInPr
ofPkts
The value of
tmnxPortNetEgrQDroInProfPkts indicates
the number of conforming network egress
packets dropped on this port using this
queue-group queue.
(16 of 20)
E-34
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portNetEgrQDroOutProfOcts
UINT128
tmnxPortNetEgrQDroOutP
rofOcts
The value of
tmnxPortNetEgrQDroOutProfOcts
indicates the number of exceeding
network egress octets dropped on this
port using this queue-group queue.
portNetEgrQDroOutProfPkts
UINT128
tmnxPortNetEgrQDroOutP
rofPkts
The value of
tmnxPortNetEgrQDroOutProfPkts
indicates the number of exceeding
network egress packets dropped on this
port using this queue-group queue.
portNetEgrQFwdInProfOcts
UINT128
tmnxPortNetEgrQFwdInPr
ofOcts
The value of
tmnxPortNetEgrQFwdInProfOcts indicates
the number of conforming network egress
octets forwarded on this port using this
queue-group queue.
portNetEgrQFwdInProfPkts
UINT128
tmnxPortNetEgrQFwdInPr
ofPkts
The value of
tmnxPortNetEgrQFwdInProfPkts indicates
the number of conforming network egress
packets forwarded on this port using this
queue-group queue.
portNetEgrQFwdOutProfOcts
UINT128
tmnxPortNetEgrQFwdOut
ProfOcts
The value of
tmnxPortNetEgrQFwdOutProfOcts
indicates the number of exceeding
network egress octets forwarded on this
port using this queue-group queue.
portNetEgrQFwdOutProfPkts
UINT128
tmnxPortNetEgrQFwdOut
ProfPkts
The value of
tmnxPortNetEgrQFwdOutProfPkts
indicates the number of exceeding
network egress packets forwarded on this
port using this queue-group queue.
portNetEgrQStatQueueId
long
tmnxPortEgrQosQStatQue
ueId
The value of
tmnxPortEgrQosQStatQueueId specifies
the queue-group queue ID which is used as
the fourth index to the table entry.
QosDroppedOctetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngrMdaQosStatTable
Monitored class: equipment.PhysicalPort
qosClassifier0DroppedOctets
UINT128
tmnxPortIngrMdaQos00St
atDropOcts
tmnxPortIngrMdaQos00StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier10DroppedOctets
UINT128
tmnxPortIngrMdaQos10St
atDropOcts
tmnxPortIngrMdaQos10StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier11DroppedOctets
UINT128
tmnxPortIngrMdaQos11St
atDropOcts
tmnxPortIngrMdaQos11StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(17 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-35
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier12DroppedOctets
UINT128
tmnxPortIngrMdaQos12St
atDropOcts
tmnxPortIngrMdaQos12StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier13DroppedOctets
UINT128
tmnxPortIngrMdaQos13St
atDropOcts
tmnxPortIngrMdaQos13StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier14DroppedOctets
UINT128
tmnxPortIngrMdaQos14St
atDropOcts
tmnxPortIngrMdaQos14StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier15DroppedOctets
UINT128
tmnxPortIngrMdaQos15St
atDropOcts
tmnxPortIngrMdaQos15StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier1DroppedOctets
UINT128
tmnxPortIngrMdaQos01St
atDropOcts
tmnxPortIngrMdaQos01StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier2DroppedOctets
UINT128
tmnxPortIngrMdaQos02St
atDropOcts
tmnxPortIngrMdaQos02StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier3DroppedOctets
UINT128
tmnxPortIngrMdaQos03St
atDropOcts
tmnxPortIngrMdaQos03StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier4DroppedOctets
UINT128
tmnxPortIngrMdaQos04St
atDropOcts
tmnxPortIngrMdaQos04StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier5DroppedOctets
UINT128
tmnxPortIngrMdaQos05St
atDropOcts
tmnxPortIngrMdaQos05StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier6DroppedOctets
UINT128
tmnxPortIngrMdaQos06St
atDropOcts
tmnxPortIngrMdaQos06StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier7DroppedOctets
UINT128
tmnxPortIngrMdaQos07St
atDropOcts
tmnxPortIngrMdaQos07StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(18 of 20)
E-36
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier8DroppedOctets
UINT128
tmnxPortIngrMdaQos08St
atDropOcts
tmnxPortIngrMdaQos08StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier9DroppedOctets
UINT128
tmnxPortIngrMdaQos09St
atDropOcts
tmnxPortIngrMdaQos09StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
QosDroppedPacketStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngrMdaQosStatTable
Monitored class: equipment.PhysicalPort
qosClassifier0DroppedPackets
UINT128
tmnxPortIngrMdaQos00St
atDropPkts
tmnxPortIngrMdaQos00StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier10DroppedPackets
UINT128
tmnxPortIngrMdaQos10St
atDropPkts
tmnxPortIngrMdaQos10StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier11DroppedPackets
UINT128
tmnxPortIngrMdaQos11St
atDropPkts
tmnxPortIngrMdaQos11StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier12DroppedPackets
UINT128
tmnxPortIngrMdaQos12St
atDropPkts
tmnxPortIngrMdaQos12StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier13DroppedPackets
UINT128
tmnxPortIngrMdaQos13St
atDropPkts
tmnxPortIngrMdaQos13StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier14DroppedPackets
UINT128
tmnxPortIngrMdaQos14St
atDropPkts
tmnxPortIngrMdaQos14StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier15DroppedPackets
UINT128
tmnxPortIngrMdaQos15St
atDropPkts
tmnxPortIngrMdaQos15StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier1DroppedPackets
UINT128
tmnxPortIngrMdaQos01St
atDropPkts
tmnxPortIngrMdaQos01StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(19 of 20)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-37
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier2DroppedPackets
UINT128
tmnxPortIngrMdaQos02St
atDropPkts
tmnxPortIngrMdaQos02StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier3DroppedPackets
UINT128
tmnxPortIngrMdaQos03St
atDropPkts
tmnxPortIngrMdaQos03StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier4DroppedPackets
UINT128
tmnxPortIngrMdaQos04St
atDropPkts
tmnxPortIngrMdaQos04StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier5DroppedPackets
UINT128
tmnxPortIngrMdaQos05St
atDropPkts
tmnxPortIngrMdaQos05StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier6DroppedPackets
UINT128
tmnxPortIngrMdaQos06St
atDropPkts
tmnxPortIngrMdaQos06StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier7DroppedPackets
UINT128
tmnxPortIngrMdaQos07St
atDropPkts
tmnxPortIngrMdaQos07StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier8DroppedPackets
UINT128
tmnxPortIngrMdaQos08St
atDropPkts
tmnxPortIngrMdaQos08StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier9DroppedPackets
UINT128
tmnxPortIngrMdaQos09St
atDropPkts
tmnxPortIngrMdaQos09StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(20 of 20)
Table E-8 fr statistics
5620 SAM counter name
Type
MIB counter name
Description
InterfaceStats
MIB table name: TIMETRA-PORT-MIB.tmnxFRDlcmiTable
Monitored class: fr.Interface
lmiDiscardedMessages
long
tmnxFRDlcmiDiscardedMs
gs
tmnxFRDlcmiDiscardedMsgs indicates the
number of times the LMI agent discarded
a received message because it wasn't
expecting it, the type of message was
incorrect, or the contents of the message
were invalid.
(1 of 2)
E-38
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
lmiInvalidRxSeqNumMessages
long
tmnxFRDlcmiInvRxSeqNu
mMsgs
tmnxFRDlcmiInvRxSeqNumMsgs indicates
the number of times the LMI agent
received a message with an invalid
receive sequence number: i.e. a sequence
number that does not match the last
transmitted sequence number of the
agent.
lmiRxStatusEnquiryMessages
long
tmnxFRDlcmiRxStatusEnq
Msgs
tmnxFRDlcmiRxStatusEnqMsgs indicates
the number of LMI Status Enquiry
messages received on this Frame Relay
interface.
lmiRxStatusMessages
long
tmnxFRDlcmiRxStatusMsg
s
tmnxFRDlcmiRxStatusMsgs indicates the
number of LMI Status messages received
on this Frame Relay interface.
lmiStatusEnquiryMsgTimeouts
long
tmnxFRDlcmiStatusEnqMs
gTimeouts
tmnxFRDlcmiStatusEnqMsgTimeouts
indicates the number of times the LMI
agent did not receive a Status Enquiry
message within the allotted time.
lmiStatusMsgTimeouts
long
tmnxFRDlcmiStatusMsgTi
meouts
tmnxFRDlcmiStatusMsgTimeouts indicates
the number of times the LMI agent did not
receive a Status message within the
allotted time.
lmiTxStatusEnquiryMessages
long
tmnxFRDlcmiTxStatusEnq
Msgs
tmnxFRDlcmiTxStatusEnqMsgs indicates
the number of LMI Status Enquiry
messages transmitted on this Frame Relay
interface.
lmiTxStatusMessages
long
tmnxFRDlcmiTxStatusMsg
s
tmnxFRDlcmiTxStatusMsgs indicates the
number of LMI Status messages
transmitted on this Frame Relay
interface.
(2 of 2)
Table E-9 gsmp statistics
5620 SAM counter name
Type
MIB counter name
Description
GsmpSessionStats
MIB table name: TIMETRA-GSMP-MIB.tmnxAncpSessionStatsTable
Monitored class: gsmp.GsmpGroupNeighborSession
ancpAckReceived
long
tmnxAncpSesStatRxAck
The value of tmnxAncpSesStatRxAck
indicates the number of GSMP ACK
messages received in this ANCP session.
ancpAckTransmitted
long
tmnxAncpSesStatTxAck
The value of tmnxAncpSesStatTxAck
indicates the number of GSMP ACK
messages that were transmitted to the
ANCP neighbor in this ANCP session.
ancpLoopBackReceived
long
tmnxAncpSesStatRxLoopb
ack
The value of tmnxAncpSesStatRxLoopback
indicates the number of GSMP Loopback
messages received in this ANCP session.
ancpLoopBackTransmitted
long
tmnxAncpSesStatTxLoopb
ack
The value of tmnxAncpSesStatTxLoopback
indicates the number of GSMP Loopback
messages that were transmitted to the
ANCP neighbor in this ANCP session.
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-39
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ancpPortDownReceived
long
tmnxAncpSesStatRxPortD
own
The value of
tmnxAncpSesStatRxPortDown indicates
the number of GSMP 'PortDown' messages
received in this ANCP session.
ancpPortDownTransmitted
long
tmnxAncpSesStatTxPortD
own
The value of
tmnxAncpSesStatTxPortDown indicates
the number of GSMP 'PortDown' messages
that were transmitted to the ANCP
neighbor in this session.
ancpPortUpReceived
long
tmnxAncpSesStatRxPortU
p
The value of tmnxAncpSesStatRxPortUp
indicates the number of GSMP 'PortUp'
messages received in this ANCP session.
ancpPortUpTransmitted
long
tmnxAncpSesStatTxPortU
p
The value of tmnxAncpSesStatTxPortUp
indicates the number of GSMP 'PortUp'
messages that were transmitted to the
ANCP neighbor in this session.
ancpRstAckReceived
long
tmnxAncpSesStatRxRstAc
k
The value of tmnxAncpSesStatRxRstAck
indicates the number of GSMP RST ACK
messages received in this ANCP session.
ancpRstAckTransmitted
long
tmnxAncpSesStatTxRstAc
k
The value of tmnxAncpSesStatTxRstAck
indicates the number of GSMP RST ACK
messages that were transmitted to the
ANCP neighbor in this session.
ancpSynAckReceived
long
tmnxAncpSesStatRxSynAc
k
The value of tmnxAncpSesStatRxSynAck
indicates the number of GSMP SYN ACK
messages received in this ANCP session.
ancpSynAckTransmitted
long
tmnxAncpSesStatTxSynAc
k
The value of tmnxAncpSesStatTxSynAck
indicates the number of GSMP SYN ACK
messages that were transmitted to the
ANCP neighbor in this ANCP session.
ancpSynReceived
long
tmnxAncpSesStatRxSyn
The value of tmnxAncpSesStatRxSyn
indicates the number of GSMP SYN
messages received in this ANCP session.
ancpSynTransmitted
long
tmnxAncpSesStatTxSyn
The value of tmnxAncpSesStatTxSyn
indicates the number of GSMP SYN
messages that were transmitted to the
ANCP neighbor in this ANCP session.
ancpTransmittedDropped
long
tmnxAncpSesStatTxDrop
The value of tmnxAncpSesStatTxDrop
indicates the number of GSMP protocol
messages that were created by the system
in order for them to be sent to the ACNP
neighbor, but were never transmitted.
(2 of 2)
Table E-10 isa statistics
5620 SAM counter name
Type
MIB counter name
Description
AaGroupEgrQStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxGrpStatusEgrQTable
Monitored class: isa.AaEgrQueue
(1 of 14)
E-40
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
droInProfOcts
long
tmnxBsxGrpStatusEgrQDr
oInPOcts
The value of
tmnxBsxGrpStatusEgrQDroInPOcts
indicates the number of in profile bytes
discarded from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
droInProfPkts
long
tmnxBsxGrpStatusEgrQDr
oInPPkts
The value of
tmnxBsxGrpStatusEgrQDroInPPkts
indicates the number of in profile packets
discarded from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
droOutProfOcts
long
tmnxBsxGrpStatusEgrQDr
oOutPOcts
The value of
tmnxBsxGrpStatusEgrQDroOutPOcts
indicates the number of out of profile
bytes discarded from ingress IOMs towards
the ISA-AA MDA within this group for the
particular queue.
droOutProfPkts
long
tmnxBsxGrpStatusEgrQDr
oOutPPkts
The value of
tmnxBsxGrpStatusEgrQDroOutPPkts
indicates the number of out of profile
packets discarded from ingress IOMs
towards the ISA-AA MDA within this group
for the particular queue.
fwdInProfOcts
long
tmnxBsxGrpStatusEgrQFw
dInPOcts
The value of
tmnxBsxGrpStatusEgrQFwdInPOcts
indicates the number of in profile bytes
diverted from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
fwdInProfPkts
long
tmnxBsxGrpStatusEgrQFw
dInPPkts
The value of
tmnxBsxGrpStatusEgrQFwdInPPkts
indicates the number of in profile packets
diverted from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
fwdOutProfOcts
long
tmnxBsxGrpStatusEgrQFw
dOutPOcts
The value of
tmnxBsxGrpStatusEgrQFwdOutPOcts
indicates the number of out of profile
bytes diverted from ingress IOMs towards
the ISA-AA MDA within this group for the
particular queue.
fwdOutProfPkts
long
tmnxBsxGrpStatusEgrQFw
dOutPPkts
The value of
tmnxBsxGrpStatusEgrQFwdOutPPkts
indicates the number of out of profile
packets diverted from ingress IOMs
towards the ISA-AA MDA within this group
for the particular queue.
hCDroInProfOcts
UINT128
tmnxBsxGrpStatusEgrQHC
DroInPOcts
The value of
tmnxBsxGrpStatusEgrQHCDroInPOcts
indicates the number of in profile bytes
discarded from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
(2 of 14)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-41
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
hCDroInProfPkts
UINT128
tmnxBsxGrpStatusEgrQHC
DroInPPkts
The value of
tmnxBsxGrpStatusEgrQHCDroInPPkts
indicates the number of in profile packets
discarded from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
hCDroOutProfOcts
UINT128
tmnxBsxGrpStatusEgrQHC
DroOutPOcts
The value of
tmnxBsxGrpStatusEgrQHCDroOutPOcts
indicates the number of out of profile
bytes discarded from ingress IOMs towards
the ISA-AA MDA within this group for the
particular queue.
hCDroOutProfPkts
UINT128
tmnxBsxGrpStatusEgrQHC
DroOutPPkts
The value of
tmnxBsxGrpStatusEgrQHCDroOutPPkts
indicates the number of out of profile
packets discarded from ingress IOMs
towards the ISA-AA MDA within this group
for the particular queue.
hCFwdInProfOcts
UINT128
tmnxBsxGrpStatusEgrQHC
FwdInPOcts
The value of
tmnxBsxGrpStatusEgrQHCFwdInPOcts
indicates the number of in profile bytes
diverted from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
hCFwdInProfPkts
UINT128
tmnxBsxGrpStatusEgrQHC
FwdInPPkts
The value of
tmnxBsxGrpStatusEgrQHCFwdInPPkts
indicates the number of in profile packets
diverted from ingress IOMs towards the
ISA-AA MDA within this group for the
particular queue.
hCFwdOutProfOcts
UINT128
tmnxBsxGrpStatusEgrQHC
FwdOutPOcts
The value of
tmnxBsxGrpStatusEgrQHCFwdOutPOcts
indicates the number of out of profile
bytes diverted from ingress IOMs towards
the ISA-AA MDA within this group for the
particular queue.
hCFwdOutProfPkts
UINT128
tmnxBsxGrpStatusEgrQHC
FwdOutPPkts
The value of
tmnxBsxGrpStatusEgrQHCFwdOutPPkts
indicates the number of out of profile
packets diverted from ingress IOMs
towards the ISA-AA MDA within this group
for the particular queue.
AaGroupIngQStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxGrpStatusIngQTable
Monitored class: isa.AaIngQueue
droInProfOcts
long
tmnxBsxGrpStatusIngQDr
oInPOcts
The value of
tmnxBsxGrpStatusIngQDroInPOcts
indicates the number of in profile bytes
discarded towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
droInProfPkts
long
tmnxBsxGrpStatusIngQDr
oInPPkts
The value of
tmnxBsxGrpStatusIngQDroInPPkts
indicates the number of in profile packets
discarded towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
(3 of 14)
E-42
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
droOutProfOcts
long
tmnxBsxGrpStatusIngQDr
oOutPOcts
The value of
tmnxBsxGrpStatusIngQDroOutPOcts
indicates the number of out of profile
bytes discarded towards egress IOMs from
the ISA-AA MDA within this group for the
particular queue.
droOutProfPkts
long
tmnxBsxGrpStatusIngQDr
oOutPPkts
The value of
tmnxBsxGrpStatusIngQDroOutPPkts
indicates the number of out of profile
packets discarded towards egress IOMs
from the ISA-AA MDA within this group for
the particular queue.
fwdInProfOcts
long
tmnxBsxGrpStatusIngQFw
dInPOcts
The value of
tmnxBsxGrpStatusIngQFwdInPOcts
indicates the number of in profile bytes
diverted towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
fwdInProfPkts
long
tmnxBsxGrpStatusIngQFw
dInPPkts
The value of
tmnxBsxGrpStatusIngQFwdInPPkts
indicates the number of in profile packets
diverted towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
fwdOutProfOcts
long
tmnxBsxGrpStatusIngQFw
dOutPOcts
The value of
tmnxBsxGrpStatusIngQFwdOutPOcts
indicates the number of out of profile
bytes diverted towards egress IOMs from
the ISA-AA MDA within this group for the
particular queue.
fwdOutProfPkts
long
tmnxBsxGrpStatusIngQFw
dOutPPkts
The value of
tmnxBsxGrpStatusIngQFwdOutPPkts
indicates the number of out of profile
packets diverted towards egress IOMs
from the ISA-AA MDA within this group for
the particular queue.
hCDroInProfOcts
UINT128
tmnxBsxGrpStatusIngQHC
DroInPOcts
The value of
tmnxBsxGrpStatusIngQHCDroInPOcts
indicates the number of in profile bytes
discarded towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
hCDroInProfPkts
UINT128
tmnxBsxGrpStatusIngQHC
DroInPPkts
The value of
tmnxBsxGrpStatusIngQHCDroInPPkts
indicates the number of in profile packets
discarded towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
hCDroOutProfOcts
UINT128
tmnxBsxGrpStatusIngQHC
DroOutPOcts
The value of
tmnxBsxGrpStatusIngQHCDroOutPOcts
indicates the number of out of profile
bytes discarded towards egress IOMs from
the ISA-AA MDA within this group for the
particular queue.
(4 of 14)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-43
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
hCDroOutProfPkts
UINT128
tmnxBsxGrpStatusIngQHC
DroOutPPkts
The value of
tmnxBsxGrpStatusIngQHCDroOutPPkts
indicates the number of out of profile
packets discarded towards egress IOMs
from the ISA-AA MDA within this group for
the particular queue.
hCFwdInProfOcts
UINT128
tmnxBsxGrpStatusIngQHC
FwdInPOcts
The value of
tmnxBsxGrpStatusIngQHCFwdInPOcts
indicates the number of in profile bytes
diverted towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
hCFwdInProfPkts
UINT128
tmnxBsxGrpStatusIngQHC
FwdInPPkts
The value of
tmnxBsxGrpStatusIngQHCFwdInPPkts
indicates the number of in profile packets
diverted towards egress IOMs from the
ISA-AA MDA within this group for the
particular queue.
hCFwdOutProfOcts
UINT128
tmnxBsxGrpStatusIngQHC
FwdOutPOcts
The value of
tmnxBsxGrpStatusIngQHCFwdOutPOcts
indicates the number of out of profile
bytes diverted towards egress IOMs from
the ISA-AA MDA within this group for the
particular queue.
hCFwdOutProfPkts
UINT128
tmnxBsxGrpStatusIngQHC
FwdOutPPkts
The value of
tmnxBsxGrpStatusIngQHCFwdOutPPkts
indicates the number of out of profile
packets diverted towards egress IOMs
from the ISA-AA MDA within this group for
the particular queue.
AaSapSumStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxAaSubSumTable
Monitored class: isa.AaSapInfo
aaSap
String
tmnxBsxAaSubscriber
The Application Assurance Subscriber
identifier. The format of this object is
determined by the value of the
tmnxBsxAaSubscriberType.
BsxMdaStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxGrpStatusTable
Monitored classes:
equipment.Shelf
equipment.DaughterCardSlot
•
•
flows
long
tmnxBsxGrpStatusFlows
The value of tmnxBsxGrpStatusFlows
indicates the number of flows seen by the
ISA-AA MDA(s). Note that if the same
5-tuple is seen for a different flow within
the flow timeout, it will still be
considered one flow.
flowsCurrent
long
tmnxBsxGrpStatusFlowsC
urrent
The value of
tmnxBsxGrpStatusFlowsCurrent indicates
the number of flows currently being
tracked by the ISA-AA MDA(s).
(5 of 14)
E-44
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
flowSetupRate
long
tmnxBsxGrpStatusFlowSe
tupRate
The value of
tmnxBsxGrpStatusFlowSetupRate
indicates the number of flow setups per
second. The calculation is weighted to
give half of the weight to flows setup
within the last five minutes and 25
weighting to flows setup in the previous
five minutes, etc.
hCFlows
UINT128
tmnxBsxGrpStatusHCFlow
s
The value of tmnxBsxGrpStatusHCFlows
indicates the number of flows seen by the
ISA-AA MDA(s). Note that if the same
5-tuple is seen for a different flow within
the flow timeout, it will still be
considered one flow.
hCOctsDiscCongIn
UINT128
tmnxBsxGrpStatusHCOcts
DiscCongIn
The value of
tmnxBsxGrpStatusHCOctsDiscCongIn
indicates the number of bytes discarded
by the IOMs prior to the ISA-AA MDA(s) due
to egress IOM congestion.
hCOctsDiscCongMda
UINT128
tmnxBsxGrpStatusHCOcts
DisCongMda
The value of
tmnxBsxGrpStatusHCOctsDisCongMda
indicates the number of bytes discarded
by the ISA-AA MDA(s) due to congestion.
hCOctsDiscCongOut
UINT128
tmnxBsxGrpStatusHCOcts
DisCongOut
The value of
tmnxBsxGrpStatusHCOctsDisCongOut
indicates the number of bytes discarded
by the IOMs after the ISA-AA MDA(s) due to
ingress IOM congestion.
hCOctsDiscErrors
UINT128
tmnxBsxGrpStatusHCOcts
DiscErrors
The value of
tmnxBsxGrpStatusHCOctsDiscErrors
indicates the number of bytes discarded
due to unrecoverable errors.
hCOctsDiscPolicy
UINT128
tmnxBsxGrpStatusHCOcts
DiscPolicy
The value of
tmnxBsxGrpStatusHCOctsDiscPolicy
indicates the number of bytes discarded
by the ISA-AA MDA(s) due to policy
policers or discard actions.
hCOctsFromMda
UINT128
tmnxBsxGrpStatusHCOcts
FromMda
The value of
tmnxBsxGrpStatusHCOctsFromMda
indicates the number of bytes sent from
the ISA-AA MDA(s) to the local IOM.
hCOctsIn
UINT128
tmnxBsxGrpStatusHCOcts
In
The value of tmnxBsxGrpStatusHCOctsIn
indicates the number of bytes diverted
from ingress IOMs towards the ISA-AA
MDA(s).
hCOctsInMda
UINT128
tmnxBsxGrpStatusHCOcts
InMda
The value of
tmnxBsxGrpStatusHCOctsInMda indicates
the number of bytes buffered by the
ISA-AA MDA(s).
hCOctsInspected
UINT128
tmnxBsxGrpStatusHCOcts
Inspected
The value of
tmnxBsxGrpStatusHCOctsInspected
indicates the number of bytes sent for
protocol determination by the ISA-AA
MDA(s).
(6 of 14)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-45
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
hCOctsOut
UINT128
tmnxBsxGrpStatusHCOcts
Out
The value of tmnxBsxGrpStatusHCOctsOut
indicates the number of bytes sent to
egress IOMs from the ISA-AA MDA(s).
hCOctsPolicyByPass
UINT128
tmnxBsxGrpStatusHCOcts
PolicyByps
The value of
tmnxBsxGrpStatusHCOctsPolicyByps
indicates the number of bytes passed
untouched that did not have statistics or
policy applied.
hCOctsToMda
UINT128
tmnxBsxGrpStatusHCOcts
ToMda
The value of
tmnxBsxGrpStatusHCOctsToMda indicates
the number of bytes sent from an IOM
towards the ISA-AA MDA(s).
hCPktsDiscCongIn
UINT128
tmnxBsxGrpStatusHCPkts
DiscCongIn
The value of
tmnxBsxGrpStatusHCPktsDiscCongIn
indicates the number of packets
discarded by the IOMs prior to the ISA-AA
MDA(s) due to egress IOM congestion.
hCPktsDiscCongMda
UINT128
tmnxBsxGrpStatusHCPkts
DisCongMda
The value of
tmnxBsxGrpStatusHCPktsDisCongMda
indicates the number of packets
discarded by the ISA-AA MDA(s) due to
congestion.
hCPktsDiscCongOut
UINT128
tmnxBsxGrpStatusHCPkts
DisCongOut
The value of
tmnxBsxGrpStatusHCPktsDisCongOut
indicates the number of packets
discarded by the IOMs after the ISA-AA
MDA(s) due to ingress IOM congestion.
hCPktsDiscErrors
UINT128
tmnxBsxGrpStatusHCPkts
DiscErrors
The value of
tmnxBsxGrpStatusHCPktsDiscErrors
indicates the number of packets
discarded due to unrecoverable errors.
hCPktsDiscPolicy
UINT128
tmnxBsxGrpStatusHCPkts
DiscPolicy
The value of
tmnxBsxGrpStatusHCPktsDiscPolicy
indicates the number of packets
discarded by the ISA-AA MDA(s) due to
policy policers or discard actions.
hCPktsFromMda
UINT128
tmnxBsxGrpStatusHCPkts
FromMda
The value of
tmnxBsxGrpStatusHCPktsFromMda
indicates the number of packets sent from
the ISA-AA MDA(s) to the local IOM.
hCPktsIn
UINT128
tmnxBsxGrpStatusHCPktsI
n
The value of tmnxBsxGrpStatusHCPktsIn
indicates the number of packets diverted
from ingress IOMs towards the ISA-AA
MDA(s).
hCPktsInMda
UINT128
tmnxBsxGrpStatusHCPktsI
nMda
The value of
tmnxBsxGrpStatusHCPktsInMda indicates
the number of packets buffered by the
ISA-AA MDA(s).
hCPktsInPchipErrors
UINT128
tmnxBsxGrpStatusHCPktsI
nPChipErs
The value of
tmnxBsxGrpStatusHCPktsInPChipErs
indicates the number of packets
discarded by the egress P-chip due to
errors in the packets.
(7 of 14)
E-46
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
hCPktsInspected
UINT128
tmnxBsxGrpStatusHCPktsI
nspected
The value of
tmnxBsxGrpStatusHCPktsInspected
indicates the number of packets sent for
protocol determination by the ISA-AA
MDA(s).
hCPktsOut
UINT128
tmnxBsxGrpStatusHCPkts
Out
The value of tmnxBsxGrpStatusHCPktsOut
indicates the number of packets sent to
egress IOMs from the ISA-AA MDA(s).
hCPktsOutPchipErrors
UINT128
tmnxBsxGrpStatusHCPkts
OutPChipEr
The value of
tmnxBsxGrpStatusHCPktsOutPChipEr
indicates the number of packets
discarded by the ingress P-chip due to
errors in the packets.
hCPktsPolicyByPass
UINT128
tmnxBsxGrpStatusHCPkts
PolicyByps
The value of
tmnxBsxGrpStatusHCPktsPolicyByps
indicates the number of packets passed
untouched that did not have statistics or
policy applied.
hCPktsToMda
UINT128
tmnxBsxGrpStatusHCPkts
ToMda
The value of
tmnxBsxGrpStatusHCPktsToMda indicates
the number of packets sent from an IOM
towards the ISA-AA MDA(s).
octsDiscCongIn
long
tmnxBsxGrpStatusOctsDis
cCongIn
The value of
tmnxBsxGrpStatusOctsDiscCongIn
indicates the number of bytes discarded
by the IOMs prior to the ISA-AA MDA(s) due
to egress IOM congestion.
octsDiscCongMda
long
tmnxBsxGrpStatusOctsDis
CongMda
The value of
tmnxBsxGrpStatusOctsDisCongMda
indicates the number of bytes discarded
by the ISA-AA MDA(s) due to congestion.
octsDiscCongOut
long
tmnxBsxGrpStatusOctsDis
CongOut
The value of
tmnxBsxGrpStatusOctsDisCongOut
indicates the number of bytes discarded
by the IOMs after the ISA-AA MDA(s) due to
ingress IOM congestion.
octsDiscErrors
long
tmnxBsxGrpStatusOctsDis
cErrors
The value of
tmnxBsxGrpStatusOctsDiscErrors
indicates the number of bytes discarded
due to unrecoverable errors.
octsDiscPolicy
long
tmnxBsxGrpStatusOctsDis
cPolicy
The value of
tmnxBsxGrpStatusOctsDiscPolicy
indicates the number of bytes discarded
by the ISA-AA MDA(s) due to policy.
octsFromMda
long
tmnxBsxGrpStatusOctsFro
mMda
The value of
tmnxBsxGrpStatusOctsFromMda indicates
the number of bytes sent from the ISA-AA
MDA(s) to the local IOM.
octsIn
long
tmnxBsxGrpStatusOctsIn
The value of tmnxBsxGrpStatusOctsIn
indicates the number of bytes diverted
from ingress IOMs towards the ISA-AA
MDA(s).
octsInMda
long
tmnxBsxGrpStatusOctsIn
Mda
The value of tmnxBsxGrpStatusOctsInMda
indicates the number of bytes buffered by
the ISA-AA MDA(s).
(8 of 14)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-47
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
octsInspected
long
tmnxBsxGrpStatusOctsIns
pected
The value of
tmnxBsxGrpStatusOctsInspected
indicates the number of bytes sent for
protocol determination by the ISA-AA
MDA(s).
octsOut
long
tmnxBsxGrpStatusOctsOu
t
The value of tmnxBsxGrpStatusOctsOut
indicates the number of bytes sent to
egress IOMs from the ISA-AA MDA(s).
octsPolicyByPass
long
tmnxBsxGrpStatusOctsPol
icyByps
The value of
tmnxBsxGrpStatusOctsPolicyByps
indicates the number of bytes passed
untouched that did not have statistics or
policy applied.
octsToMda
long
tmnxBsxGrpStatusOctsTo
Mda
The value of tmnxBsxGrpStatusOctsToMda
indicates the number of bytes sent from
an IOM towards the ISA-AA MDA(s).
pktsDiscCongIn
long
tmnxBsxGrpStatusPktsDis
cCongIn
The value of
tmnxBsxGrpStatusPktsDiscCongIn
indicates the number of packets
discarded by the IOMs prior to the ISA-AA
MDA(s) due to egress IOM congestion.
pktsDiscCongMda
long
tmnxBsxGrpStatusPktsDis
CongMda
The value of
tmnxBsxGrpStatusPktsDisCongMda
indicates the number of packets
discarded by the ISA-AA MDA(s) due to
congestion.
pktsDiscCongOut
long
tmnxBsxGrpStatusPktsDis
CongOut
The value of
tmnxBsxGrpStatusPktsDisCongOut
indicates the number of packets
discarded by the IOMs after the ISA-AA
MDA(s) due to ingress IOM congestion.
pktsDiscErrors
long
tmnxBsxGrpStatusPktsDis
cErrors
The value of
tmnxBsxGrpStatusPktsDiscErrors
indicates the number of packets
discarded due to unrecoverable errors.
pktsDiscPolicy
long
tmnxBsxGrpStatusPktsDis
cPolicy
The value of
tmnxBsxGrpStatusPktsDiscPolicy
indicates the number of packets
discarded by the ISA-AA MDA(s) due to
policy.
pktsFromMda
long
tmnxBsxGrpStatusPktsFro
mMda
The value of
tmnxBsxGrpStatusPktsFromMda indicates
the number of packets sent from the
ISA-AA MDA(s) to the local IOM.
pktsIn
long
tmnxBsxGrpStatusPktsIn
The value of tmnxBsxGrpStatusPktsIn
indicates the number of packets diverted
from ingress IOMs towards the ISA-AA
MDA(s).
pktsInMda
long
tmnxBsxGrpStatusPktsInM
da
The value of tmnxBsxGrpStatusPktsInMda
indicates the number of packets buffered
by the ISA-AA MDA(s).
pktsInPChipErrors
long
tmnxBsxGrpStatusPktsInP
ChipErs
The value of
tmnxBsxGrpStatusPktsInPChipErs
indicates the number of packets
discarded by the egress P-chip due to
errors in the packets.
(9 of 14)
E-48
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
pktsInspected
long
tmnxBsxGrpStatusPktsIns
pected
The value of
tmnxBsxGrpStatusPktsInspected indicates
the number of packets sent for protocol
determination by the ISA-AA MDA(s).
pktsOut
long
tmnxBsxGrpStatusPktsOu
t
The value of tmnxBsxGrpStatusPktsOut
indicates the number of packets sent to
egress IOMs from the ISA-AA MDA(s).
pktsOutPChipErrors
long
tmnxBsxGrpStatusPktsOu
tPChipEr
The value of
tmnxBsxGrpStatusPktsOutPChipEr
indicates the number of packets
discarded by the ingress P-chip due to
errors in the packets.
pktsPolicyByPass
long
tmnxBsxGrpStatusPktsPol
icyByps
The value of
tmnxBsxGrpStatusPktsPolicyByps
indicates the number of packets passed
untouched that did not have statistics or
policy applied.
pktsToMda
long
tmnxBsxGrpStatusPktsTo
Mda
The value of tmnxBsxGrpStatusPktsToMda
indicates the number of packets sent from
an IOM towards the ISA-AA MDA(s).
subsCurrent
long
tmnxBsxGrpStatusSubsCu
rrent
The value of
tmnxBsxGrpStatusSubsCurrent indicates
the number of subscribers currently with
flow records in the ISA-AA MDA(s).
subsDiverted
long
tmnxBsxGrpStatusSubsDiv
erted
The value of
tmnxBsxGrpStatusSubsDiverted indicates
the number of subscribers defined in
TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSu
bInfoAppProfile in the
tmnxSubscriberInfoTable with
tmnxBsxAppProfDivert set to 'true'.
trafficRate
long
tmnxBsxGrpStatusTraffic
Rate
The value of
tmnxBsxGrpStatusTrafficRate indicates
the traffic rate in kilo-bits per second
(kbps) incoming to the ISA-AA MDA(s).
VideoGroupMemberStats
MIB table name: TIMETRA-VIDEO-MIB.tmnxVdoGrpMDATable
Monitored class: isa.VideoGroupMember
vdoGrpMdaActiveRtcpSessions
long
tmnxVdoGrpMdaActiveRt
cpSessions
The value of
tmnxVdoGrpMdaActiveRtcpSessions
indicates the number of active Real Time
Transport Control Protocol (RTCP)
sessions on this MDA.
vdoGrpMdaAdStreamAborts
long
tmnxVdoGrpMdaAdStrea
mAborts
The value of
tmnxVdoGrpMdaAdStreamAborts
indicates the number of ad stream aborts
on this MDA. An ad stream abort could
happen when an egress reset happens.
vdoGrpMdaAdStreamResets
long
tmnxVdoGrpMdaAdStrea
mResets
The value of
tmnxVdoGrpMdaAdStreamResets
indicates the number of ad stream resets
on this MDA. An ad stream reset occurs
when the ingress ad stream stops.
(10 of 14)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-49
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpMdaAvailableMemory
long
tmnxVdoGrpMdaAvailable
Memory
The value of
tmnxVdoGrpMdaAvailableMemory
indicates the amount of cache available
on the MDA for storing the video stream.
vdoGrpMdaBwInUse
long
tmnxVdoGrpMdaBwInUse
The value of tmnxVdoGrpMdaBwInUse
indicates the total aggregate bandwidth
of the currently running egress streams.
vdoGrpMdaChannelAllocFails
long
tmnxVdoGrpMdaChannel
AllocFails
The value of
tmnxVdoGrpMdaChannelAllocFails
indicates the number of failed channel
allocations on this MDA.
vdoGrpMdaChannels
long
tmnxVdoGrpMdaChannels
The value of tmnxVdoGrpMdaChannels
indicates the number of channels being
served on this MDA.
vdoGrpMdaEgressStreamResets
long
tmnxVdoGrpMdaEgressStr
eamResets
The value of
tmnxVdoGrpMdaEgressStreamResets
indicates the number of egress stream
resets on this MDA. An egress stream reset
occurs when there are no packets to
transmit on the MDA.
vdoGrpMdaHighPktPoolLimitHit
long
tmnxVdoGrpMdaHighPktP
oolLimitHit
The value of
tmnxVdoGrpMdaHighPktPoolLimitHit
indicates the number of times the high
packet pool limit has been hit. A high
value of this object indicates potential
failure in ingress packet storage.
vdoGrpMdaIngressStreamResets
long
tmnxVdoGrpMdaIngressSt
reamResets
The value of
tmnxVdoGrpMdaIngressStreamResets
indicates the number of ingress stream
resets on this MDA. An ingress stream
reset occurs when the ingress stream
stopped coming in for more than one
second.
vdoGrpMdaMaxBwExceeded
long
tmnxVdoGrpMdaMaxBwEx
ceeded
The value of
tmnxVdoGrpMdaMaxBwExceeded
indicates the number of times maximum
allowed bandwidth has been exceeded for
each egress stream.
vdoGrpMdaRequestedRtpPkts
long
tmnxVdoGrpMdaRequeste
dRtpPkts
The value of
tmnxVdoGrpMdaRequestedRtpPkts
indicates the number of Real-time
Transport Protocol (RTP) packets
requested in the Real-time Transport
Control Protocol (RTCP) feedback (FB)
messages received on this MDA.
vdoGrpMdaRtcpConfigErrors
long
tmnxVdoGrpMdaRtcpConf
igErrors
The value of
tmnxVdoGrpMdaRtcpConfigErrors
indicates the number of Real-time
Transport Control Protocol (RTCP) config
errors on this MDA. These errors occur
when there is inconsistency between the
RTCP values and the configured values.
vdoGrpMdaRtcpIntErrors
long
tmnxVdoGrpMdaRtcpIntEr
rors
The value of
tmnxVdoGrpMdaRtcpIntErrors indicates
the number of Real-time Transport
Control Protocol (RTCP) interface related
errors on this MDA.
(11 of 14)
E-50
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpMdaRtcpIpcErrors
long
tmnxVdoGrpMdaRtcpIpcE
rrors
The value of
tmnxVdoGrpMdaRtcpIpcErrors indicates
the number of Real-time Transport
Control Protocol (RTCP) inter-process
communication message processing errors
on this MDA.
vdoGrpMdaRtcpParseErrors
long
tmnxVdoGrpMdaRtcpPars
eErrors
The value of
tmnxVdoGrpMdaRtcpParseErrors
indicates the number of Real-time
Transport Control Protocol (RTCP) packet
parsing errors on this MDA.
vdoGrpMdaRtcpSgErrors
long
tmnxVdoGrpMdaRtcpSgEr
rors
The value of
tmnxVdoGrpMdaRtcpSgErrors indicates
the number of Real-time Transport
Control Protocol (RTCP) channel errors on
this MDA. These errors occue when a
channel is not found for a given interface
to process RTCP packets.
vdoGrpMdaRtcpSubErrors
long
tmnxVdoGrpMdaRtcpSubE
rrors
The value of
tmnxVdoGrpMdaRtcpSubErrors indicates
the number of Real-time Transport
Control Protocol (RTCP) subscriber
parameter errors on this MDA. These
errors occur when the subscriber
calculations exceed the maximum
allowed bandwidth.
vdoGrpMdaRxDataOctets
UINT128
tmnxVdoGrpMdaRxDataO
ctets
The value of
tmnxVdoGrpMdaRxDataOctets indicates
the number of data octets received on
this MDA.
vdoGrpMdaRxDataOctetsHigh32
long
tmnxVdoGrpMdaRxDataO
ctetsHigh32
The value of
tmnxVdoGrpMdaRxDataOctetsHigh32
indicates the higher 32 bits of the value of
tmnxVdoGrpMdaRxDataOctets.
vdoGrpMdaRxDataOctetsLow32
long
tmnxVdoGrpMdaRxDataO
ctetsLow32
The value of
tmnxVdoGrpMdaRxDataOctetsLow32
indicates the lower 32 bits of the value of
tmnxVdoGrpMdaRxDataOctets.
vdoGrpMdaRxDataPacketErrors
UINT128
tmnxVdoGrpMdaRxDataP
acketErrors
The value of
tmnxVdoGrpMdaRxDataPacketErrors
indicates the number of malformed or
non-RTP (Real Time Transport Protocol)
packets received on this MDA.
vdoGrpMdaRxDataPackets
UINT128
tmnxVdoGrpMdaRxDataP
ackets
The value of
tmnxVdoGrpMdaRxDataPackets indicates
the number of data packets received on
this MDA.
vdoGrpMdaRxDataPacketsHigh32
long
tmnxVdoGrpMdaRxDataP
acketsHigh32
The value of
tmnxVdoGrpMdaRxDataPacketsHigh32
indicates the higher 32 bits of the value of
tmnxVdoGrpMdaRxDataPackets.
vdoGrpMdaRxDataPacketsLow32
long
tmnxVdoGrpMdaRxDataP
acketsLow32
The value of
tmnxVdoGrpMdaRxDataPacketsLow32
indicates the lower 32 bits of the value of
tmnxVdoGrpMdaRxDataPackets.
(12 of 14)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-51
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpMdaRxDataPktErrsHigh32
long
tmnxVdoGrpMdaRxDataP
ktErrsHigh32
The value of
tmnxVdoGrpMdaRxDataPktErrsHigh32
indicates the higher 32 bits of the value of
tmnxVdoGrpMdaRxDataPacketErrors.
vdoGrpMdaRxDataPktErrsLow32
long
tmnxVdoGrpMdaRxDataP
ktErrsLow32
The value of
tmnxVdoGrpMdaRxDataPktErrsLow32
indicates the lower 32 bits of the value of
tmnxVdoGrpMdaRxDataPacketErrors.
vdoGrpMdaSsrcCollisions
long
tmnxVdoGrpMdaSsrcCollis
ions
The value of
tmnxVdoGrpMdaSsrcCollisions indicates
the number of synchronization source
(SSRC) id collisions on this MDA.
vdoGrpMdaTxDataOctets
UINT128
tmnxVdoGrpMdaTxDataO
ctets
The value of
tmnxVdoGrpMdaTxDataOctets indicates
the number of data octets transmitted on
this MDA.
vdoGrpMdaTxDataOctetsHigh32
long
tmnxVdoGrpMdaTxDataO
ctetsHigh32
The value of
tmnxVdoGrpMdaTxDataOctetsHigh32
indicates the higher 32 bits of the value of
tmnxVdoGrpMdaTxDataOctets.
vdoGrpMdaTxDataOctetsLow32
long
tmnxVdoGrpMdaTxDataO
ctetsLow32
The value of
tmnxVdoGrpMdaTxDataOctetsLow32
indicates the lower 32 bits of the value of
tmnxVdoGrpMdaTxDataOctets.
vdoGrpMdaTxDataPacketErrors
UINT128
tmnxVdoGrpMdaTxDataP
acketErrors
The value of
tmnxVdoGrpMdaTxDataPacketErrors
indicates the number of failed data
packets due to lack of resources to be
transmitted on this MDA.
vdoGrpMdaTxDataPackets
UINT128
tmnxVdoGrpMdaTxDataP
ackets
The value of
tmnxVdoGrpMdaTxDataPackets indicates
the number of data packets transmitted
on this MDA.
vdoGrpMdaTxDataPacketsHigh32
long
tmnxVdoGrpMdaTxDataP
acketsHigh32
The value of
tmnxVdoGrpMdaTxDataPacketsHigh32
indicates the higher 32 bits of the value of
tmnxVdoGrpMdaTxDataPackets.
vdoGrpMdaTxDataPacketsLow32
long
tmnxVdoGrpMdaTxDataP
acketsLow32
The value of
tmnxVdoGrpMdaTxDataPacketsLow32
indicates the lower 32 bits of the value of
tmnxVdoGrpMdaTxDataPackets.
vdoGrpMdaTxDataPktErrsHigh32
long
tmnxVdoGrpMdaTxDataP
ktErrsHigh32
The value of
tmnxVdoGrpMdaTxDataPktErrsHigh32
indicates the higher 32 bits of the value of
tmnxVdoGrpMdaTxDataPacketErrors.
vdoGrpMdaTxDataPktErrsLow32
long
tmnxVdoGrpMdaTxDataP
ktErrsLow32
The value of
tmnxVdoGrpMdaTxDataPktErrsLow32
indicates the lower 32 bits of the value of
tmnxVdoGrpMdaTxDataPacketErrors.
(13 of 14)
E-52
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpMdaTxLostPackets
long
tmnxVdoGrpMdaTxLostPa
ckets
The value of
tmnxVdoGrpMdaTxLostPackets indicates
the number of packets not found in the
video MDA buffer for retransmission.
When a retransmission request arrives,
packets are checked in the buffer and if
they are not found, the value of this
object is incremented.
vdoGrpMdaUsedMemory
long
tmnxVdoGrpMdaUsedMe
mory
The value of
tmnxVdoGrpMdaUsedMemory indicates
the amount of cache being used by the
video group for storing the video stream.
(14 of 14)
Table E-11 isis statistics
5620 SAM counter name
Type
MIB counter name
Description
InterfaceLevelOneReceivingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelOneConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelOneSendingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelOneConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelTwoReceivingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelTwoConfig
(1 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-53
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelTwoSendingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelTwoConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
LinkStatePduSiteStats
MIB table name: TIMETRA-ISIS-MIB.vRtrIsisStatsTable
Monitored class: isis.Site
csnpDropped
long
vRtrIsisCSNPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisCSNPDrop.
csnpReceived
long
vRtrIsisCSNPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisCSNPRecd.
csnpRetransmitted
long
vRtrIsisCSNPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisCSNPRetrans.
csnpSent
long
vRtrIsisCSNPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisCSNPSent.
helloDropped
long
vRtrIsisIIHDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisIIHDrop.
helloReceived
long
vRtrIsisIIHRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisIIHRecd.
(2 of 4)
E-54
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
helloRetransmitted
long
vRtrIsisIIHRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisIIHRetrans.
helloSent
long
vRtrIsisIIHSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisIIHSent.
lspDropped
long
vRtrIsisLSPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisLSPDrop.
lspReceived
long
vRtrIsisLSPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisLSPRecd.
lspRetransmitted
long
vRtrIsisLSPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisLSPRetrans.
lspSent
long
vRtrIsisLSPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisLSPSent.
psnpDropped
long
vRtrIsisPSNPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisPSNPDrop.
psnpReceived
long
vRtrIsisPSNPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisPSNPRecd.
psnpRetransmitted
long
vRtrIsisPSNPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisPSNPRetrans.
psnpSent
long
vRtrIsisPSNPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisPSNPSent.
unknownDropped
long
vRtrIsisUnknownDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisUnknownDrop.
unknownReceived
long
vRtrIsisUnknownRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisUnknownRecd.
unknownRetransmitted
long
vRtrIsisUnknownRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisUnknownRetrans.
unknownSent
long
vRtrIsisUnknownSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisUnknownSent.
SiteStats
MIB table name: TIMETRA-ISIS-MIB.vRtrIsisStatsTable
Monitored class: isis.Site
cspfDroppedRequests
long
vRtrIsisCSPFDroppedRequ
ests
vRtrIsisCSPFDroppedRequests maintains
the number of dropped CSPF requests by
the protocol.
(3 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-55
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
cspfPathsFound
long
vRtrIsisCSPFPathsFound
vRtrIsisCSPFPathsFound maintains the
number of responses to CSPF requests for
which paths satisfying the constraints
were found.
cspfPathsNotFound
long
vRtrIsisCSPFPathsNotFoun
d
vRtrIsisCSPFPathsFound maintains the
number of responses to CSPF requests for
which no paths satisfying the constraints
were found.
cspfRequests
long
vRtrIsisCSPFRequests
vRtrIsisCSPFRequests maintains the
number of CSPF requests made to the
protocol.
initiatedPurges
long
vRtrIsisInitiatedPurges
The value of vRtrIsisInitiatedPurges
counts the number of times purges have
been initiated.
lspRegenerations
long
vRtrIsisLSPRegenerations
The value of vRtrIsisLSPRegenerations
maintains the count of LSP regenerations.
spfRuns
long
vRtrIsisSpfRuns
The value of vRtrIsisSpfRuns indicates the
number of times shortest path first
calculations have been made.
(4 of 4)
Table E-12 l2fib statistics
5620 SAM counter name
Type
MIB counter name
Description
MFibGrpSrcStats
MIB table name: TIMETRA-SERV-MIB.tlsMFibStatsTable
Monitored class: l2fib.MFibGrpSrc
forwardedOctets
UINT128
tlsMFibStatsForwardedOc
tets
The value of
tlsMFibStatsForwardedOctets indicates
the number of octets that were forwarded
to the SAPs and SDPs listed in the
tlsMFibInfoTable.
forwardedPkts
UINT128
tlsMFibStatsForwardedPk
ts
The value of tlsMFibStatsForwardedPkts
indicates the number of multicast packets
that were forwarded to the SAPs and SDPs
listed in the tlsMFibInfoTable.
Table E-13 l2fwd statistics
5620 SAM counter name
Type
MIB counter name
Description
sapTlsStpForwardTransiti
ons
The value of the object
sapTlsStpForwardTransitions indicates
the number of times this port has
transitioned from the Learning state to
the Forwarding state.
AccessInterfaceStpStats
MIB table name: TIMETRA-SAP-MIB.sapTlsInfoTable
Monitored class: l2fwd.AccessInterfaceStp
forwardTransitions
long
(1 of 6)
E-56
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
inBadBpdus
long
sapTlsStpInBadBpdus
This object specifies the number of bad
BPDUs received on this SAP.
inConfigBpdus
long
sapTlsStpInConfigBpdus
The value of the object
sapTlsStpInConfigBpdus indicates the
number of Configuration BPDUs received
on this SAP.
inMultipleSpanningTreeBpdus
long
sapTlsStpInMstBpdus
The value of the object
sapTlsStpInMstBpdus indicates the
number of Multiple Spanning Tree (MST)
BPDUs received on this SAP.
inRapidSpanningTreeBpdus
long
sapTlsStpInRstBpdus
The value of the object
sapTlsStpInRstBpdus indicates the number
of Rapid Spanning Tree (RST) BPDUs
received on this SAP.
inTcnBpdus
long
sapTlsStpInTcnBpdus
The value of the object
sapTlsStpInTcnBpdus indicates the
number of Topology Change Notification
BPDUs received on this SAP.
outConfigBpdus
long
sapTlsStpOutConfigBpdus
The value of the object
sapTlsStpOutConfigBpdus indicates the
number of Configuration BPDUs sent out
this SAP.
outMultipleSpanningTreeBpdus
long
sapTlsStpOutMstBpdus
The value of the object
sapTlsStpOutMstBpdus indicates the
number of Multiple Spanning Tree (MST)
BPDUs sent out on this SAP.
outRapidSpanningTreeBpdus
long
sapTlsStpOutRstBpdus
The value of the object
sapTlsStpOutRstBpdus indicates the
number of Rapid Spanning Tree (RST)
BPDUs sent out on this SAP.
outTcnBpdus
long
sapTlsStpOutTcnBpdus
This object specifies the number of
Topology Change Notification BPDUs sent
out this SAP.
CircuitMrpInfoStats
MIB table name: TIMETRA-SDP-MIB.sdpBindTlsMrpTable
Monitored class: l2fwd.CircuitMrpInfo
mrpDroppedPdus
long
sdpBindTlsMrpDroppedPd
us
The value of sdpBindTlsMrpDroppedPdus
indicates the number of dropped MRP
packets on this SDP Bind.
mrpRxEmptyEvent
long
sdpBindTlsMrpRxEmptyEv
ent
The value of sdpBindTlsMrpRxEmptyEvent
indicates the number of 'Empty' MRP
events received on this SDP Bind.
mrpRxInEvent
long
sdpBindTlsMrpRxInEvent
The value of sdpBindTlsMrpRxInEvent
indicates the number of 'In' MRP events
received on this SDP Bind.
mrpRxJoinEmptyEvent
long
sdpBindTlsMrpRxJoinEmp
tyEvent
The value of
sdpBindTlsMrpRxJoinEmptyEvent
indicates the number of 'Join Empty' MRP
events received on this SDP Bind.
mrpRxJoinInEvent
long
sdpBindTlsMrpRxJoinInEv
ent
The value of sdpBindTlsMrpRxJoinInEvent
indicates the number of 'Join-In' MRP
events received on this SDP Bind.
(2 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-57
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
mrpRxLeaveEvent
long
sdpBindTlsMrpRxLeaveEv
ent
The value of sdpBindTlsMrpRxLeaveEvent
indicates the number of 'Leave' MRP
events received on this SDP Bind.
mrpRxNewEvent
long
sdpBindTlsMrpRxNewEven
t
The value of sdpBindTlsMrpRxNewEvent
indicates the number of 'New' MRP events
received on this SDP Bind.
mrpRxPdus
long
sdpBindTlsMrpRxPdus
The value of sdpBindTlsMrpRxPdus
indicates the number of MRP packets
received on this SDP Bind.
mrpTxEmptyEvent
long
sdpBindTlsMrpTxEmptyEv
ent
The value of sdpBindTlsMrpTxEmptyEvent
indicates the number of 'Empty' MRP
events transmitted on this SDP Bind.
mrpTxInEvent
long
sdpBindTlsMrpTxInEvent
The value of sdpBindTlsMrpTxInEvent
indicates the number of 'In' MRP events
transmitted on this SDP Bind.
mrpTxJoinEmptyEvent
long
sdpBindTlsMrpTxJoinEmp
tyEvent
The value of
sdpBindTlsMrpTxJoinEmptyEvent
indicates the number of 'Join Empty' MRP
events transmitted on this SDP Bind.
mrpTxJoinInEvent
long
sdpBindTlsMrpTxJoinInEv
ent
The value of sdpBindTlsMrpTxJoinInEvent
indicates the number of 'Join-In' MRP
events transmitted on this SDP Bind.
mrpTxLeaveEvent
long
sdpBindTlsMrpTxLeaveEv
ent
The value of sdpBindTlsMrpTxLeaveEvent
indicates the number of 'Leave' MRP
events transmitted on this SDP Bind.
mrpTxNewEvent
long
sdpBindTlsMrpTxNewEven
t
The value of sdpBindTlsMrpTxNewEvent
indicates the number of 'New' MRP events
transmitted on this SDP Bind.
mrpTxPdus
long
sdpBindTlsMrpTxPdus
The value of sdpBindTlsMrpTxPdus
indicates the number of MRP packets
transmitted on this SDP Bind.
CircuitStpStats
MIB table name: TIMETRA-SDP-MIB.sdpBindTlsTable
Monitored class: l2fwd.CircuitStp
forwardTransitions
long
sdpBindTlsStpForwardTra
nsitions
The value of the object
sdpBindTlsStpForwardTransitions
indicates the number of times this port
has transitioned from the Learning state
to the Forwarding state.
inBadBpdus
long
sdpBindTlsStpInBadBpdus
The value of the object
sdpBindTlsStpInBadBpdus indicates the
number of bad BPDUs received on this SDP
Bind.
inConfigBpdus
long
sdpBindTlsStpInConfigBpd
us
The value of the object
sdpBindTlsStpInConfigBpdus indicates the
number of Configuration BPDUs received
on this SDP Bind.
inRapidSpanningTreeBpdus
long
sdpBindTlsStpInRstBpdus
The value of the object
sdpBindTlsStpInRstBpdus indicates the
number of Rapid Spanning Tree (Rst)
BPDUs received on this SDP.
(3 of 6)
E-58
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
inTcnBpdus
long
sdpBindTlsStpInTcnBpdus
The value of the object
sdpBindTlsStpInTcnBpdus indicates the
number of Topology Change Notification
BPDUs received on this SDP Bind.
outConfigBpdus
long
sdpBindTlsStpOutConfigB
pdus
The value of the object
sdpBindTlsStpOutConfigBpdus indicates
the number of Configuration BPDUs sent
out this SDP Bind.
outRapidSpanningTreeBpdus
long
sdpBindTlsStpOutRstBpdu
s
The value of the object
sdpBindTlsStpOutRstBpdus indicates the
number of Rapid Spanning Tree (Rstp)
BPDUs sent out on this SDP.
outTcnBpdus
long
sdpBindTlsStpOutTcnBpd
us
The value of the object
sdpBindTlsStpOutTcnBpdus indicates the
number of Topology Change Notification
BPDUs sent out this SDP Bind.
L2AccessInterfaceMrpInfoStats
MIB table name: TIMETRA-SAP-MIB.sapTlsMrpTable
Monitored class: l2fwd.L2AccessInterfaceMrpInfo
mrpDroppedPdus
long
sapTlsMrpDroppedPdus
The value of sapTlsMrpDroppedPdus
indicates the number of dropped MRP
packets on this SAP.
mrpRxEmptyEvent
long
sapTlsMrpRxEmptyEvent
The value of sapTlsMrpRxEmptyEvent
indicates the number of 'Empty' MRP
events received on this SAP.
mrpRxInEvent
long
sapTlsMrpRxInEvent
The value of sapTlsMrpRxInEvent
indicates the number of 'In' MRP events
received on this SAP.
mrpRxJoinEmptyEvent
long
sapTlsMrpRxJoinEmptyEv
ent
The value of sapTlsMrpRxJoinEmptyEvent
indicates the number of 'Join Empty' MRP
events received on this SAP.
mrpRxJoinInEvent
long
sapTlsMrpRxJoinInEvent
The value of sapTlsMrpRxJoinInEvent
indicates the number of 'Join-In' MRP
events received on this SAP.
mrpRxLeaveEvent
long
sapTlsMrpRxLeaveEvent
The value of sapTlsMrpRxLeaveEvent
indicates the number of 'Leave' MRP
events received on this SAP.
mrpRxNewEvent
long
sapTlsMrpRxNewEvent
The value of sapTlsMrpRxNewEvent
indicates the number of 'New' MRP events
received on this SAP.
mrpRxPdus
long
sapTlsMrpRxPdus
The value of sapTlsMrpRxPdus indicates
the number of MRP packets received on
this SAP.
mrpTxEmptyEvent
long
sapTlsMrpTxEmptyEvent
The value of sapTlsMrpTxEmptyEvent
indicates the number of 'Empty' MRP
events transmitted on this SAP.
mrpTxInEvent
long
sapTlsMrpTxInEvent
The value of sapTlsMrpTxInEvent
indicates the number of 'In' MRP events
transmitted on this SAP.
mrpTxJoinEmptyEvent
long
sapTlsMrpTxJoinEmptyEv
ent
The value of sapTlsMrpTxJoinEmptyEvent
indicates the number of 'Join Empty' MRP
events transmitted on this SAP.
(4 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-59
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
mrpTxJoinInEvent
long
sapTlsMrpTxJoinInEvent
The value of sapTlsMrpTxJoinInEvent
indicates the number of 'Join-In' MRP
events transmitted on this SAP.
mrpTxLeaveEvent
long
sapTlsMrpTxLeaveEvent
The value of sapTlsMrpTxLeaveEvent
indicates the number of 'Leave' MRP
events transmitted on this SAP.
mrpTxNewEvent
long
sapTlsMrpTxNewEvent
The value of sapTlsMrpTxNewEvent
indicates the number of 'New' MRP events
transmitted on this SAP.
mrpTxPdus
long
sapTlsMrpTxPdus
The value of sapTlsMrpTxPdus indicates
the number of MRP packets transmitted
on this SAP.
PipStpInfoStats
MIB table name: TIMETRA-SERV-MIB.tlsPipInfoTable
Monitored class: l2fwd.PipStpInfo
pipStpForwardTransitions
long
tlsPipStpForwardTransitio
ns
The value of the object
tlsPipStpForwardTransitions indicates the
number of times this port has transitioned
from the Learning state to the Forwarding
state.
pipStpInBadBpdus
long
tlsPipStpInBadBpdus
This object specifies the number of bad
BPDUs received on this PIP uplink.
pipStpInConfigBpdus
long
tlsPipStpInConfigBpdus
The value of the object
tlsPipStpInConfigBpdus indicates the
number of Configuration BPDUs received
on this PIP uplink.
pipStpInMstBpdus
long
tlsPipStpInMstBpdus
The value of the object
tlsPipStpInMstBpdus indicates the number
of Multiple Spanning Tree (MST) BPDUs
received on this PIP uplink.
pipStpInRstBpdus
long
tlsPipStpInRstBpdus
The value of the object
tlsPipStpInRstBpdus indicates the number
of Rapid Spanning Tree (RST) BPDUs
received on this PIP uplink.
pipStpInTcnBpdus
long
tlsPipStpInTcnBpdus
The value of the object
tlsPipStpInTcnBpdus indicates the number
of Topology Change Notification BPDUs
received on this PIP uplink.
pipStpOutConfigBpdus
long
tlsPipStpOutConfigBpdus
The value of the object
tlsPipStpOutConfigBpdus indicates the
number of Configuration BPDUs sent out
this PIP uplink.
pipStpOutMstBpdus
long
tlsPipStpOutMstBpdus
The value of the object
tlsPipStpOutMstBpdus indicates the
number of Multiple Spanning Tree (MST)
BPDUs sent out on this PIP uplink.
pipStpOutRstBpdus
long
tlsPipStpOutRstBpdus
The value of the object
tlsPipStpOutRstBpdus indicates the
number of Rapid Spanning Tree (RST)
BPDUs sent out on this PIP uplink.
pipStpOutTcnBpdus
long
tlsPipStpOutTcnBpdus
This object specifies the number of
Topology Change Notification BPDUs sent
out this PIP uplink.
(5 of 6)
E-60
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
SiteFibStats
MIB table name: TIMETRA-SERV-MIB.svcTlsInfoTable
Monitored class: l2fwd.SiteFib
entries
long
svcTlsFdbNumEntries
The value of the object
svcTlsFdbNumEntries indicates the
current number of entries in the FDB of
this service.
provisionedSize
long
svcTlsFdbTableSize
The value of the object
svcTlsFdbTableSize specifies the
maximum number of learned and static
entries allowed in the FDB of this service.
The maximum value of
svcTlsFdbTableSize is '511999', when the
the value of
TIMETRA-CHASSIS-MIB::tmnxChassisOper
Mode is 'd'. The maximum value of
svcTlsFdbTableSize is '196607', when the
the value of
TIMETRA-CHASSIS-MIB::tmnxChassisOper
Mode is 'c'. In other cases, the maximum
value of svcTlsFdbTableSize is '131071'.
DEFVAL { 250 }.
staticEntries
long
svcTlsFdbNumStaticEntri
es
The value of the object
svcTlsFdbNumStaticEntries indicates the
current number of static entries in the
FDB of this service.
SiteStpStats
MIB table name: TIMETRA-SERV-MIB.svcTlsInfoTable
Monitored class: l2fwd.SiteStp
timeSinceTopologyChange
long
svcTlsStpTimeSinceTopol
ogyChange
The value of the object
svcTlsStpTimeSinceTopologyChange
indicates the time (in hundredths of a
second) since the last time a topology
change was detected by the Spanning
Tree Protocol instance associated with
this service.
topologyChanges
long
svcTlsStpTopologyChange
s
The value of the object
svcTlsStpTopologyChanges indicates the
total number of topology changes
detected by the Spanning Tree Protocol
instance associated with this service since
the management entity was last reset or
initialized.
(6 of 6)
Table E-14 lag statistics
5620 SAM counter name
Type
MIB counter name
Description
LagStats
MIB table name: TIMETRA-LAG-MIB.tLagOperationTable
Monitored class: lag.Interface
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-61
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portThresholdFalling
long
tLagPortThresholdFalling
counts the number of linkDown or
dynamicCost events for the Link
Aggregation Group caused by the number
of physical ports being less than or equal
to tLagPortThreshold value.
portThresholdRising
long
tLagPortThresholdRising
counts the number of linkUp or
dynamicCost events for the Link
Aggregation Group caused by the number
of physical ports being greater than
tLagPortThreshold value.
MultiChassisLagMemberStats
MIB table name: TIMETRA-MC-REDUNDANCY-MIB.tmnxMcLagLagStatsTable
Monitored classes:
•
•
lag.MultiChassisLagMember
multichassis.MultiChassisLagMember
configPacketsReceived
long
tmnxMcLagLagStatsPktsR
xConfig
The value of
tmnxMcLagLagStatsPktsRxConfig
indicates how many MC-Lag control
packets of type lag config were received
on this system from the peer for this lag.
configPacketsTransmitted
long
tmnxMcLagLagStatsPktsT
xConfig
The value of
tmnxMcLagLagStatsPktsTxConfig
indicates how many MC-Lag control
packets of type lag config were sent on
this system to the peer for this lag.
failedPacketsTransmitted
long
tmnxMcLagLagStatsPktsT
xFailed
The value of
tmnxMcLagLagStatsPktsTxFailed
indicates how many MC-Lag control
packets failed to be transmitted on this
system to the peer for this lag.
statePacketsReceived
long
tmnxMcLagLagStatsPktsR
xState
The value of
tmnxMcLagLagStatsPktsRxState indicates
how many MC-Lag control packets of type
lag state were received on this system
from the peer for this lag.
statePacketsTransmitted
long
tmnxMcLagLagStatsPktsT
xState
The value of
tmnxMcLagLagStatsPktsTxState indicates
how many MC-Lag control packets of type
lag state were sent on this system to the
peer for this lag.
(2 of 2)
Table E-15 ldp statistics
5620 SAM counter name
Type
MIB counter name
Description
InterfaceStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpIfStatsTable
Monitored class: ldp.Interface
existingAdjacencies
long
vRtrLdpIfExistingAdjacen
cies
The value of vRtrLdpIfExistingAdjacencies
gives a count of the total active
adjacencies on this LDP interface or with
this targeted peer.
(1 of 8)
E-62
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
LdpEgressStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpEgrStatisticsTable
Monitored class: ldp.AccountingFecPrefix
ldpInProfileOctetsFc0
UINT128
vRtrLdpInProfileOctetsFc
0
The value of vRtrLdpInProfileOctetsFc0
indicates the number of in profile octets
received for Forwarding Class 0.
ldpInProfileOctetsFc1
UINT128
vRtrLdpInProfileOctetsFc
1
The value of vRtrLdpInProfileOctetsFc1
indicates the number of in profile octets
received for Forwarding Class 1.
ldpInProfileOctetsFc2
UINT128
vRtrLdpInProfileOctetsFc
2
The value of vRtrLdpInProfileOctetsFc2
indicates the number of in profile octets
received for Forwarding Class 2.
ldpInProfileOctetsFc3
UINT128
vRtrLdpInProfileOctetsFc
3
The value of vRtrLdpInProfileOctetsFc3
indicates the number of in profile octets
received for Forwarding Class 3.
ldpInProfileOctetsFc4
UINT128
vRtrLdpInProfileOctetsFc
4
The value of vRtrLdpInProfileOctetsFc4
indicates the number of in profile octets
received for Forwarding Class 4.
ldpInProfileOctetsFc5
UINT128
vRtrLdpInProfileOctetsFc
5
The value of vRtrLdpInProfileOctetsFc5
indicates the number of in profile octets
received for Forwarding Class 5.
ldpInProfileOctetsFc6
UINT128
vRtrLdpInProfileOctetsFc
6
The value of vRtrLdpInProfileOctetsFc6
indicates the number of in profile octets
received for Forwarding Class 6.
ldpInProfileOctetsFc7
UINT128
vRtrLdpInProfileOctetsFc
7
The value of vRtrLdpInProfileOctetsFc7
indicates the number of in profile octets
received for Forwarding Class 7.
ldpInProfilePktsFc0
UINT128
vRtrLdpInProfilePktsFc0
The value of vRtrLdpInProfilePktsFc0
indicates the number of in profile packets
received for Forwarding Class 0.
ldpInProfilePktsFc1
UINT128
vRtrLdpInProfilePktsFc1
The value of vRtrLdpInProfilePktsFc1
indicates the number of in profile packets
received for Forwarding Class 1.
ldpInProfilePktsFc2
UINT128
vRtrLdpInProfilePktsFc2
The value of vRtrLdpInProfilePktsFc2
indicates the number of in profile packets
received for Forwarding Class 2.
ldpInProfilePktsFc3
UINT128
vRtrLdpInProfilePktsFc3
The value of vRtrLdpInProfilePktsFc3
indicates the number of in profile packets
received for Forwarding Class 3.
ldpInProfilePktsFc4
UINT128
vRtrLdpInProfilePktsFc4
The value of vRtrLdpInProfilePktsFc4
indicates the number of in profile packets
received for Forwarding Class 4.
ldpInProfilePktsFc5
UINT128
vRtrLdpInProfilePktsFc5
The value of vRtrLdpInProfilePktsFc5
indicates the number of in profile packets
received for Forwarding Class 5.
ldpInProfilePktsFc6
UINT128
vRtrLdpInProfilePktsFc6
The value of vRtrLdpInProfilePktsFc6
indicates the number of in profile packets
received for Forwarding Class 6.
ldpInProfilePktsFc7
UINT128
vRtrLdpInProfilePktsFc7
The value of vRtrLdpInProfilePktsFc7
indicates the number of in profile packets
received for Forwarding Class 7.
(2 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-63
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ldpOutOfProfOctetsFc0
UINT128
vRtrLdpOutOfProfOctetsF
c0
The value of vRtrLdpOutOfProfOctetsFc0
indicates the number of out of profile
octets received for Forwarding Class 0.
ldpOutOfProfOctetsFc1
UINT128
vRtrLdpOutOfProfOctetsF
c1
The value of vRtrLdpOutOfProfOctetsFc1
indicates the number of out of profile
octets received for Forwarding Class 1.
ldpOutOfProfOctetsFc2
UINT128
vRtrLdpOutOfProfOctetsF
c2
The value of vRtrLdpOutOfProfOctetsFc2
indicates the number of out of profile
octets received for Forwarding Class 2.
ldpOutOfProfOctetsFc3
UINT128
vRtrLdpOutOfProfOctetsF
c3
The value of vRtrLdpOutOfProfOctetsFc3
indicates the number of out of profile
octets received for Forwarding Class 3.
ldpOutOfProfOctetsFc4
UINT128
vRtrLdpOutOfProfOctetsF
c4
The value of vRtrLdpOutOfProfOctetsFc4
indicates the number of out of profile
octets received for Forwarding Class 4.
ldpOutOfProfOctetsFc5
UINT128
vRtrLdpOutOfProfOctetsF
c5
The value of vRtrLdpOutOfProfOctetsFc5
indicates the number of out of profile
octets received for Forwarding Class 5.
ldpOutOfProfOctetsFc6
UINT128
vRtrLdpOutOfProfOctetsF
c6
The value of vRtrLdpOutOfProfOctetsFc6
indicates the number of out of profile
octets received for Forwarding Class 6.
ldpOutOfProfOctetsFc7
UINT128
vRtrLdpOutOfProfOctetsF
c7
The value of vRtrLdpOutOfProfOctetsFc7
indicates the number of out of profile
octets received for Forwarding Class 7.
ldpOutOfProfPktsFc0
UINT128
vRtrLdpOutOfProfPktsFc0
The value of vRtrLdpOutOfProfPktsFc0
indicates the number of out of profile
packets received for Forwarding Class 0.
ldpOutOfProfPktsFc1
UINT128
vRtrLdpOutOfProfPktsFc1
The value of vRtrLdpOutOfProfPktsFc1
indicates the number of out of profile
packets received for Forwarding Class 1.
ldpOutOfProfPktsFc2
UINT128
vRtrLdpOutOfProfPktsFc2
The value of vRtrLdpOutOfProfPktsFc2
indicates the number of out of profile
packets received for Forwarding Class 2.
ldpOutOfProfPktsFc3
UINT128
vRtrLdpOutOfProfPktsFc3
The value of vRtrLdpOutOfProfPktsFc3
indicates the number of out of profile
packets received for Forwarding Class 3.
ldpOutOfProfPktsFc4
UINT128
vRtrLdpOutOfProfPktsFc4
The value of vRtrLdpOutOfProfPktsFc4
indicates the number of out of profile
packets received for Forwarding Class 4.
ldpOutOfProfPktsFc5
UINT128
vRtrLdpOutOfProfPktsFc5
The value of vRtrLdpOutOfProfPktsFc5
indicates the number of out of profile
packets received for Forwarding Class 5.
ldpOutOfProfPktsFc6
UINT128
vRtrLdpOutOfProfPktsFc6
The value of vRtrLdpOutOfProfPktsFc6
indicates the number of out of profile
packets received for Forwarding Class 6.
ldpOutOfProfPktsFc7
UINT128
vRtrLdpOutOfProfPktsFc7
The value of vRtrLdpOutOfProfPktsFc7
indicates the number of out of profile
packets received for Forwarding Class 7.
SessionStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpSessionStatsTable
Monitored class: ldp.Session
(3 of 8)
E-64
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
addressMessagesReceived
long
vRtrLdpSessStatsAddrIn
The value of vRtrLdpSessStatsAddrIn
counts the number of Address Messages
that have been received during this
session.
addressMessagesSent
long
vRtrLdpSessStatsAddrOut
The value of vRtrLdpSessStatsAddrOut
counts the number of Address Messages
that have been sent during this session.
addressWithdrawMessagesReceive
d
long
vRtrLdpSessStatsAddrWit
hdrawIn
The value of
vRtrLdpSessStatsAddrWithdrawIn counts
the number of Address Withdraw
Messages that have been received during
this session.
addressWithdrawMessagesSent
long
vRtrLdpSessStatsAddrWit
hdrawOut
The value of
vRtrLdpSessStatsAddrWithdrawOut counts
the number of Address Withdraw
Messages that have been sent during this
session.
fecReceived
long
vRtrLdpSessStatsFECRecv
The value of vRtrLdpSessStatsFECRecv
counts the number of FECs received for
this session.
fecSent
long
vRtrLdpSessStatsFECSent
The value of vRtrLdpSessStatsFECSent
counts the number of FECs sent for this
session.
helloMessagesReceived
long
vRtrLdpSessStatsHelloIn
The value of vRtrLdpSessStatsHelloIn
counts the number of Hello Messages that
have been received during this session.
helloMessagesSent
long
vRtrLdpSessStatsHelloOut
The value of vRtrLdpSessStatsHelloOut
counts the number of Hello Messages that
have been sent during this session.
initMessagesReceived
long
vRtrLdpSessStatsInitIn
The value of vRtrLdpSessStatsInitIn counts
the number of Init Messages that have
been received during this session.
initMessagesSent
long
vRtrLdpSessStatsInitOut
The value of vRtrLdpSessStatsInitOut
counts the number of Init Messages that
have been sent during this session.
keepAliveMessagesReceived
long
vRtrLdpSessStatsKeepaliv
eIn
The value of vRtrLdpSessStatsKeepaliveIn
counts the number of Keepalive Messages
that have been received during this
session.
keepAliveMessagesSent
long
vRtrLdpSessStatsKeepaliv
eOut
The value of
vRtrLdpSessStatsKeepaliveOut counts the
number of Keepalive Messages that have
been sent during this session.
labelAbortsReceived
long
vRtrLdpSessStatsLabelAb
ortIn
The value of
vRtrLdpSessStatsLabelAbortIn counts the
number of Label Abort Messages that have
been received during this session.
labelAbortsSent
long
vRtrLdpSessStatsLabelAb
ortOut
The value of
vRtrLdpSessStatsLabelAbortOut counts
the number of Label Abort Messages that
have been sent during this session.
(4 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-65
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
labelMappingsReceived
long
vRtrLdpSessStatsLabelMa
ppingIn
The value of
vRtrLdpSessStatsLabelMappingIn counts
the number of Label Mapping Messages
that have been received during this
session.
labelMappingsSent
long
vRtrLdpSessStatsLabelMa
ppingOut
The value of
vRtrLdpSessStatsLabelMappingOut counts
the number of Label Mapping Messages
that have been sent during this session.
labelReleasesReceived
long
vRtrLdpSessStatsLabelRel
easeIn
The value of
vRtrLdpSessStatsLabelReleaseIn counts
the number of Label Release Messages
that have been received during this
session.
labelReleasesSent
long
vRtrLdpSessStatsLabelRel
easeOut
The value of
vRtrLdpSessStatsLabelReleaseOut counts
the number of Label Release Messages
that have been sent during this session.
labelRequestsReceived
long
vRtrLdpSessStatsLabelRe
questIn
The value of
vRtrLdpSessStatsLabelRequestIn counts
the number of Label Request Messages
that have been received during this
session.
labelRequestsSent
long
vRtrLdpSessStatsLabelRe
questOut
The value of
vRtrLdpSessStatsLabelRequestOut counts
the number of Label Request Messages
that have been sent during this session.
labelWithdrawsReceived
long
vRtrLdpSessStatsLabelWit
hdrawIn
The value of
vRtrLdpSessStatsLabelWithdrawIn counts
the number of Label Withdraw Messages
that have been received during this
session.
labelWithdrawsSent
long
vRtrLdpSessStatsLabelWit
hdrawOut
The value of
vRtrLdpSessStatsLabelWithdrawOut
counts the number of Label Withdraw
Messages that have been sent during this
session.
linkAdjacencies
long
vRtrLdpSessStatsLinkAdj
The value of vRtrLdpSessStatsLinkAdj
specifies the number of link adjacencies
for this session.
notificationMessagesReceived
long
vRtrLdpSessStatsNotificat
ionIn
The value of
vRtrLdpSessStatsNotificationIn counts the
number of Notification Messages that
have been received during this session.
notificationMessagesSent
long
vRtrLdpSessStatsNotificat
ionOut
The value of
vRtrLdpSessStatsNotificationOut counts
the number of Notification Messages that
have been sent during this session.
targetedAdjacencies
long
vRtrLdpSessStatsTargAdj
The value of vRtrLdpSessStatsTargAdj
specifies the number of targeted
adjacencies for this session.
SiteStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpStatsTable
Monitored class: ldp.Site
(5 of 8)
E-66
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
activeAdjacencies
long
vRtrLdpStatsActiveAdjac
encies
The value of
vRtrLdpStatsActiveAdjacencies specifies
the number of active adjacencies (i.e.
established sessions) associated with the
LDP instance.
activeInterfaces
long
vRtrLdpStatsActiveInterfa
ces
The value of vRtrLdpStatsActiveInterfaces
specifies the number of active (i.e.
operationally up) interfaces associated
with the LDP instance.
activeSessions
long
vRtrLdpStatsActiveSessio
ns
The value of vRtrLdpStatsActiveSessions
specifies the number of active sessions
(i.e. session in some form of creation)
associated with the LDP instance.
activeTargetedSessions
long
vRtrLdpStatsActiveTargSe
ssions
The value of
vRtrLdpStatsActiveTargSessions specifies
the number of active (i.e. operationally
up) targeted sessions associated with the
LDP instance.
addressFECsReceived
long
vRtrLdpStatsAddrFECRecv
The value of vRtrLdpStatsAddrFECRecv
specifies the number of Address FECs
received by the LDP instance from its
neighbors.
addressFECsSent
long
vRtrLdpStatsAddrFECSent
The value of vRtrLdpStatsAddrFECSent
specifies the number of Address FECs sent
by the LDP instance to its neighbors.
attemptedSessions
long
vRtrLdpStatsAttemptedSe
ssions
The value of
vRtrLdpStatsAttemptedSessions specifies
the total number of attempted sessions
for this LDP instance.
badLdpIdentifierErrors
long
vRtrLdpStatsBadLdpIdenti
fierErrors
The value of
vRtrLdpStatsBadLdpIdentifierErrors gives
the number of Bad LDP Identifier Fatal
Errors detected for sessions associated
with this LDP instance. REFERENCE LDP
Specification, Section 3.5.1.2.
badMessageLengthErrors
long
vRtrLdpStatsBadMessageL
engthErrors
The value of
vRtrLdpStatsBadMessageLengthErrors
gives the number of Bad Message Length
Fatal Errors detected for sessions
associated with this LDP instance.
REFERENCE LDP Specification, Section
3.5.1.2.
badPduLengthErrors
long
vRtrLdpStatsBadPduLengt
hErrors
The value of
vRtrLdpStatsBadPduLengthErrors gives
the number of Bad Pdu Length Fatal Errors
detected for sessions associated with this
LDP instance. REFERENCE LDP
Specification, Section 3.5.1.2.
badTlvLengthErrors
long
vRtrLdpStatsBadTlvLengt
hErrors
The value of
vRtrLdpStatsBadTlvLengthErrors gives the
number of Bad TLV Length Fatal Errors
detected for sessions associated with this
LDP instance. REFERENCE LDP
Specification, Section 3.5.1.2.
(6 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-67
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
inactiveInterfaces
long
vRtrLdpStatsInactiveInter
faces
The value of
vRtrLdpStatsInactiveInterfaces specifies
the number of inactive (i.e. operationally
down) interfaces associated with the LDP
instance.
inactiveTargetedSessions
long
vRtrLdpStatsInactiveTarg
Sessions
The value of
vRtrLdpStatsInactiveTargSessions
specifies the number of inactive (i.e.
operationally down) targeted sessions
associated with the LDP instance.
keepAliveExpiredErrors
long
vRtrLdpStatsKeepAliveEx
piredErrors
The value of
vRtrLdpStatsKeepAliveExpiredErrors gives
the number of Session Keep Alive Timer
Expired Errors detected for sessions
associated with this LDP instance.
REFERENCE LDP Specification, Section
3.5.1.2.
malformedTlvValueErrors
long
vRtrLdpStatsMalformedTl
vValueErrors
The value of
vRtrLdpStatsMalformedTlvValueErrors
gives the number of Malformed TLV Value
Fatal Errors detected for sessions
associated with this LDP instance.
REFERENCE LDP Specification, Section
3.5.1.2.
operDownEvents
long
vRtrLdpStatsOperDownEv
ents
The value of
vRtrLdpStatsOperDownEvents specifies
the number of times the LDP instance has
gone operationally down since the
instance was created.
serviceFECsReceived
long
vRtrLdpStatsSvcFECRecv
The value of vRtrLdpStatsSvcFECRecv
specifies the number of Service FECs
received by the LDP instance from its
neighbors.
serviceFECsSent
long
vRtrLdpStatsSvcFECSent
The value of vRtrLdpStatsSvcFECSent
specifies the number of Service FECs sent
by the LDP instance to its neighbors.
sessionRejectedAdvertisementMod
eErrors
long
vRtrLdpStatsSessRejAdvE
rrors
The value of
vRtrLdpStatsSessRejAdvErrors gives the
total number of Session
Rejected/Parameters Advertisement
Mode Error Notification Messages sent or
received by this LDP instance.
sessionRejectedLabelRangeErrors
long
vRtrLdpStatsSessRejLabel
RangeErrors
The value of
vRtrLdpStatsSessRejLabelRangeErrors
gives the total number of Session
Rejected/Parameters Label Range Error
Notification Messages sent or received by
this LDP instance.
sessionRejectedMaxPduLengthErro
rs
long
vRtrLdpStatsSessRejMaxP
duErrors
The value of
vRtrLdpStatsSessRejMaxPduErrors gives
the total number of Session
Rejected/Parameters Max Pdu Length
Error Notification Messages sent or
received by this LDP instance.
(7 of 8)
E-68
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sessionRejectedNoHelloErrors
long
vRtrLdpStatsSessRejNoHe
lloErrors
The value of
vRtrLdpStatsSessRejNoHelloErrors gives
the total number of Session Rejected/No
Hello Error Notification Messages sent or
received by this LDP instance.
shutdownNotificationsReceived
long
vRtrLdpStatsShutdownNo
tifRecv
The value of
vRtrLdpStatsShutdownNotifRecv gives the
number of Shutdown Notifications
received related to sessions associated
with this LDP instance.
shutdownNotificationsSent
long
vRtrLdpStatsShutdownNo
tifSent
The value of
vRtrLdpStatsShutdownNotifSent gives the
number of Shutdown Notifications sent
related to sessions associated with this
LDP instance.
TargetedPeerStats
MIB table name: TIMETRA-LDP-MIB.vRtrLdpIfStatsTable
Monitored class: ldp.TargetedPeer
existingAdjacencies
long
vRtrLdpIfExistingAdjacen
cies
The value of vRtrLdpIfExistingAdjacencies
gives a count of the total active
adjacencies on this LDP interface or with
this targeted peer.
(8 of 8)
Table E-16 lldp statistics
5620 SAM counter name
Type
MIB counter name
Description
LLDPRxPortStats
MIB table name: TIMETRA-LLDP-MIB.tmnxLldpStatsRxPortTable
Monitored class: lldp.LLDPPortConfiguration
(1 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-69
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
lldpStatsRxPortAgeouts
long
tmnxLldpStatsRxPortAgeo
uts
The counter that represents the number
of age-outs that occurred on a given port.
An age-out is the number of times the
complete set of information advertised by
a particular MSAP has been deleted from
tables contained in
tmnxLldpRemoteSystemsData and
lldpExtensions objects because the
information timeliness interval has
expired. This counter is similar to
lldpStatsRemTablesAgeouts, except that
the counter is on a per port basis. This
enables NMS to poll tables associated with
the tmnxLldpRemoteSystemsData objects
and all LLDP extension objects associated
with remote systems on the indicated
port only. This counter should be set to
zero during agent initialization and its
value should not be saved in non-volatile
storage. When a port's admin status
changes from 'disabled' to 'rxOnly', 'txOnly'
or 'txAndRx', the counter associated with
the same port should reset to 0. The agent
should also flush all remote system
information associated with the same
port. This counter should be incremented
only once when the complete set of
information is invalidated (aged out) from
all related tables on a particular port.
Partial ageing is not allowed, and thus,
should not change the value of this
counter. REFERENCE IEEE Std
802.1AB-200X 10.5.2.
lldpStatsRxPortFrameDiscard
long
tmnxLldpStatsRxPortFra
meDiscard
The number of LLDP frames received by
this LLDP agent on the indicated port, and
then discarded for any reason. This
counter can provide an indication that
LLDP header formating problems may
exist with the local LLDP agent in the
sending system or that LLDPDU validation
problems may exist with the local LLDP
agent in the receiving system. REFERENCE
IEEE Std 802.1AB-200X 10.5.2.
lldpStatsRxPortFrameErrs
long
tmnxLldpStatsRxPortFra
meErrs
The number of invalid LLDP frames
received by this LLDP agent on the
indicated port, while this LLDP agent is
enabled. REFERENCE IEEE Std
802.1AB-200X 10.5.2.
lldpStatsRxPortFrames
long
tmnxLldpStatsRxPortFra
mes
The number of valid LLDP frames received
by this LLDP agent on the indicated port,
while this LLDP agent is enabled.
REFERENCE IEEE Std 802.1AB-200X 10.5.2.
lldpStatsRxPortTLVDiscard
long
tmnxLldpStatsRxPortTLV
Discard
The number of LLDP TLVs discarded for
any reason by this LLDP agent on the
indicated port. REFERENCE IEEE Std
802.1AB-200X 10.5.2.
(2 of 3)
E-70
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
lldpStatsRxPortTLVUnknown
long
tmnxLldpStatsRxPortTLV
Unknown
The number of LLDP TLVs received on the
given port that are not recognized by this
LLDP agent on the indicated port. An
unrecognized TLV is referred to as the TLV
whose type value is in the range of
reserved TLV types (000 1001 - 111 1110)
in Table 9.1 of IEEE Std 802.1AB-2004. An
unrecognized TLV may be a basic
management TLV from a later LLDP
version. REFERENCE IEEE Std
802.1AB-200X 10.5.2.
LLDPTxPortStats
MIB table name: TIMETRA-LLDP-MIB.tmnxLldpStatsTxPortTable
Monitored class: lldp.LLDPPortConfiguration
lldpStatsTxLLDPDULengthErrs
long
tmnxLldpStatsTxLLDPDUL
engthErrs
The number of LLDPD Length Errors
recorded for the Port. REFERENCE IEEE
Std 802.1AB-200X 10.2.7.2.
lldpStatsTxPortFrames
long
tmnxLldpStatsTxPortFra
mes
The number of LLDP frames transmitted
by this LLDP agent on the indicated port.
REFERENCE IEEE Std 802.1AB-200X 10.5.2.
(3 of 3)
Table E-17 mpls statistics
5620 SAM counter name
Type
MIB counter name
Description
DynamicLspStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspStatTable
Monitored class: mpls.DynamicLsp
configuredPaths
long
vRtrMplsLspConfiguredPa
ths
The number of paths configured for this
LSP.
operationalPaths
long
vRtrMplsLspOperationalP
aths
The number of operational paths for this
LSP. This includes the path currently
active, as well as operational standby
paths.
pathChanges
long
vRtrMplsLspPathChanges
The number of path changes this LSP has
had. For every path change (path down,
path up, path change), a corresponding
syslog/trap (if enabled) is generated for
it.
standbyPaths
long
vRtrMplsLspStandbyPaths
The number of standby paths configured
for this LSP.
timeSinceLastPathChange
long
vRtrMplsLspLastPathChan
ge
The time in 10-millisecond units since the
last change occurred on this LSP.
timeSinceLastPrimaryUpState
long
vRtrMplsLspPrimaryTime
Up
The total time in 10-millisecond units that
this LSP's primary path has been
operational. For example, the percentage
contribution of the primary path to the
operational time is given by
(vRtrMplsLspPrimaryTimeUp/vRtrMplsLsp
TimeUp * 100) .
(1 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-71
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
LspPathStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspPathStatTable
Monitored class: mpls.LspPath
cspfQueries
long
vRtrMplsLspPathCspfQuer
ies
The value of vRtrMplsLspPathCspfQueries
specifies the number of CSPF queries that
have been made for this LSP path.
retryAttempts
long
vRtrMplsLspPathRetryAtt
empts
The number of unsuccessful attempts
which have been made to signal this path.
As soon as the path gets signalled, this is
set to 0.
timeDown
long
vRtrMplsLspPathTimeDow
n
The total time in 10-millisecond units that
this LSP Path has not been operational.
timeUp
long
vRtrMplsLspPathTimeUp
The total time in 10-millisecond units that
this LSP path has been operational. For
example, the percentage up time can be
determined by computing
(vRtrMplsLspPathTimeUp/vRtrMplsLspAge
* 100 ).
transitionCount
long
vRtrMplsLspPathTransitio
nCount
The object
vRtrMplsLspPathTransitionCount
maintains the number of transitions that
have occurred for this LSP.
LspStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspStatTable
Monitored classes:
mpls.DynamicLsp
mpls.StaticLsp
mpls.BypassOnlyLsp
•
•
•
age
long
vRtrMplsLspAge
The age (i.e., time from creation till now)
of this LSP in 10-millisecond periods.
timeSinceLastDownState
long
vRtrMplsLspTimeDown
The total time in 10-millisecond units that
this LSP has not been operational.
timeSinceLastTransition
long
vRtrMplsLspLastTransitio
n
The time in 10-millisecond units since the
last transition occurred on this LSP.
timeSinceLastUpState
long
vRtrMplsLspTimeUp
The total time in 10-millisecond units that
this LSP has been been operational. For
example, the percentage up time can be
determined by computing
(vRtrMplsLspTimeUp/vRtrMplsLspAge *
100 ).
transitions
long
vRtrMplsLspTransitions
The number of state transitions (up ->
down and down -> up) this LSP has
undergone.
MplsInterfaceStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsIfStatTable
Monitored class: mpls.Interface
receiveOctets
UINT128
vRtrMplsIfRxOctetCount
The total number of bytes in MPLS labeled
packets received on this interface.
receivePackets
UINT128
vRtrMplsIfRxPktCount
The total number of MPLS labeled packets
received on this interface.
(2 of 4)
E-72
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmitOctets
UINT128
vRtrMplsIfTxOctetCount
The total number of bytes in MPLS labeled
packets transmitted on this interface.
transmitPackets
UINT128
vRtrMplsIfTxPktCount
The total number of MPLS labeled packets
transmitted from this interface.
MplsLspEgressStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspStatisticsTable
Monitored class: mpls.DynamicLsp
psbMatch
boolean
vRtrMplsLspStatsPSBMatc
h
The value of vRtrMplsLspStatsPSBMatch
indicates if a path state block (PSB) match
was made against this LSP name.
MplsLspIngressStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsLspStatisticsTable
Monitored class: mpls.IngStatsPolicy
psbMatch
boolean
vRtrMplsLspStatsPSBMatc
h
The value of vRtrMplsLspStatsPSBMatch
indicates if a path state block (PSB) match
was made against this LSP name.
SiteStats
MIB table name: TIMETRA-MPLS-MIB.vRtrMplsGeneralStatTable
Monitored class: mpls.Site
detourOriginate
long
vRtrMplsGeneralDetourLs
pOriginate
The value of
vRtrMplsGeneralDetourLspOriginate
indicates the number of detour LSPs that
originate at this virtual router.
detourTerminate
long
vRtrMplsGeneralDetourLs
pTerminate
The value of
vRtrMplsGeneralDetourLspTerminate
indicates the number of detour LSPs that
terminate at this virtual router.
detourTransit
long
vRtrMplsGeneralDetourLs
pTransit
The value of
vRtrMplsGeneralDetourLspTransit
indicates the number of detour LSPs that
transit through this virtual router.
dynamicOriginate
long
vRtrMplsGeneralDynamic
LspOriginate
The value of
vRtrMplsGeneralDynamicLspOriginate
indicates the number of dynamic LSPs
that originate at this virtual router.
dynamicTerminate
long
vRtrMplsGeneralDynamic
LspTerminate
The value of
vRtrMplsGeneralDynamicLspTerminate
indicates the number of dynamic LSPs
that terminate at this virtual router.
dynamicTransit
long
vRtrMplsGeneralDynamic
LspTransit
The value of
vRtrMplsGeneralDynamicLspTransit
indicates the number of dynamic LSPs
that transit through this virtual router.
staticOriginate
long
vRtrMplsGeneralStaticLsp
Originate
The value of
vRtrMplsGeneralStaticLspOriginate
indicates the number of static LSPs that
originate at this virtual router.
staticTerminate
long
vRtrMplsGeneralStaticLsp
Terminate
The value of
vRtrMplsGeneralStaticLspTerminate
indicates the number of static LSPs that
terminate at this virtual router.
(3 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-73
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
staticTransit
long
vRtrMplsGeneralStaticLsp
Transit
The value of
vRtrMplsGeneralStaticLspTransit
indicates the number of static LSPs that
transit through this virtual router.
(4 of 4)
Table E-18 multicast statistics
5620 SAM counter name
Type
MIB counter name
Description
McastCacChannelServiceStats
MIB table name: TIMETRA-MCAST-CAC-MIB.tmnxMcacServStatsTable
Monitored class: multicast.McastCacPolicy
action
int
tmnxMcacServStatsAction
The value of tmnxMcacServStatsAction
indicates the action specified by the mcac
policy for the service application to act
upon.
algorithmReapply
boolean
tmnxMcacServStatsAlgoR
eapply
The value of
tmnxMcacServStatsAlgoReapply indicates
if the mcac policy was reapplied on the
already accepted channel due lag
constraints or if this was the first request
for this channel from the service
application.
bundleAvailBw
long
tmnxMcacServStatsBundl
eAvailBW
The value of
tmnxMcacServStatsBundleAvailBW
indicates the available bundle bandwidth
after the requested channel was either
accepted or discarded by the mcac policy.
channelBw
long
tmnxMcacServStatsChann
elBW
The value of
tmnxMcacServStatsChannelBW indicates
the channel bandwidth configured at the
mcac policy at the time of request from
the service application.
channelRequestCount
long
tmnxMcacServStatsApply
Attempts
The value of
tmnxMcacServStatsApplyAttempts
indicates the number of times the mcac
policy was applied for a particular
channel entry by the service application.
channelType
int
tmnxMcacServStatsChann
elType
The value of
tmnxMcacServStatsChannelType indicates
the channel type configured at the mcac
policy at the time of request from the
service application.
encapValueOrVCId
String
tmnxMcacServStatsEncap
Value
The value of
tmnxMcacServStatsEncapValue indicates
the SAP/SDP Encap value of which the
mcac policy is applied.
interfaceAvailBw
long
tmnxMcacServStatsIntfAv
ailBW
The value of
tmnxMcacServStatsIntfAvailBW indicates
the available interface bandwidth after
the requested channel was either
accepted or discarded by the mcac policy.
(1 of 5)
E-74
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portIdOrTunnelId
String
tmnxMcacServStatsPortId
The value of tmnxMcacServStatsPortId
indicates the port Id of the SAP/SDP on
which the mcac policy is applied.
reason
int
tmnxMcacServStatsReaso
n
The value of tmnxMcacServStatsReason
indicates the reason for the action
specified by the mcac policy for the
service application to act upon.
timeStamp
long
tmnxMcacServStatsTimeS
tamp
The value of
tmnxMcacServStatsTimeStamp indicates
the timestamp of the last time the mcac
policy was applied for this channel entry.
McastCacChannelStats
MIB table name: TIMETRA-MCAST-CAC-MIB.tmnxMcacStatsTable
Monitored class: multicast.McastCacPolicy
action
int
tmnxMcacStatsAction
The value of tmnxMcacStatsAction
indicates the action specified by the mcac
policy for the application interface to act
upon.
algorithmReapply
boolean
tmnxMcacStatsAlgoReapp
ly
The value of tmnxMcacStatsAlgoReapply
indicates if the mcac policy was reapplied
on the already accepted channel due lag
constraints or if this was the first request
for this channel from the application.
bundleAvailBw
long
tmnxMcacStatsBundleAva
ilBW
The value of
tmnxMcacStatsBundleAvailBW indicates
the available bundle bandwidth after the
requested channel was either accepted or
discarded by the mcac policy.
bundleName
String
tmnxMcacStatsBundleNa
me
The value of tmnxMcacStatsBundleName
indicates the name of the multicast CAC
policy bundle. The value of
tmnxMcacStatsBundleName could be an
empty string, meaning that this particular
statistics entry's channel did not belong to
any bundle in the policy.
channelAddress
String
tmnxMcacStatsChlAddr
The value of tmnxMcacStatsChlAddr
indicates the address of the multicast
channel that mcac policy was applied
upon when requested by the application
interface. Address type is indicated by
tmnxMcacStatsChlAddrType.
channelAddressType
int
tmnxMcacStatsChlAddrTy
pe
The value of tmnxMcacStatsChlAddrType
indicates the address type of
tmnxMcacStatsChlAddr.
channelBw
long
tmnxMcacStatsChannelB
W
The value of tmnxMcacStatsChannelBW
indicates the channel bandwidth
configured at the mcac policy at the time
of request from the application interface.
channelRequestCount
long
tmnxMcacStatsApplyAtte
mpts
The value of
tmnxMcacStatsApplyAttempts indicates
the number of times the mcac policy was
applied for a particular channel entry by
the application.
(2 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-75
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
channelType
int
tmnxMcacStatsChannelTy
pe
The value of tmnxMcacStatsChannelType
indicates the channel type configured at
the mcac policy at the time of request
from the application interface.
interfaceAvailBw
long
tmnxMcacStatsIntfAvailB
W
The value of tmnxMcacStatsIntfAvailBW
indicates the available interface
bandwidth after the requested channel
was either accepted or discarded by the
mcac policy.
interfaceId
long
tmnxMcacStatsIfIndex
The value of tmnxMcacStatsIfIndex
indicates the application interface index
that has applied mcac policy.
protocolName
int
tmnxMcacStatsProtocolIn
dex
The value of tmnxMcacStatsProtocolIndex
indicates the application that has applied
mcac policy.
reason
int
tmnxMcacStatsReason
The value of tmnxMcacStatsReason
indicates the reason for the action
specified by the mcac policy for the
application interface to act upon.
timeStamp
long
tmnxMcacStatsTimeStam
p
The value of tmnxMcacStatsTimeStamp
indicates the timestamp of the last time
the mcac policy was applied for this
channel entry.
McastCacOper
MIB table name: TIMETRA-MCAST-CAC-MIB.tmnxMcacOperTable
Monitored class: multicast.McastCacPolicy
activeChannels
long
tmnxMcacOperActiveCha
nnels
The value of
tmnxMcacOperActiveChannels indicates
the number of active channels for this
entry.
availMandBw
long
tmnxMcacOperAvailMand
Bw
The value of tmnxMcacOperAvailMandBw
indicates the operational pre-reserved
bandwidth in kilo-bits per second(kbps)
for the mandatory channels on the bundle
for this protocol interface instance.
availOptionalBw
long
tmnxMcacOperAvailOptnl
Bw
The value of tmnxMcacOperAvailOptnlBw
indicates the operational available
bandwidth in kilo-bits per second(kbps)
on the bundle for this protocol interface
instance.
currConstrtLvl
long
tmnxMcacOperCurrConstr
tLvl
The value of
tmnxMcacOperCurrConstrtLvl indicates
the current lag constraints bundle level id
for the number of ports down
(tmnxMcacOperPortsDown). This value is
used to index the table
tmnxMcacLevelTable to get the bundle
level bandwidth.
inUseMandBw
long
tmnxMcacOperInUseMand
Bw
The value of tmnxMcacOperInUseMandBw
indicates the operational in-use
bandwidth in kilo-bits per second(kbps)
for the mandatory channels on the bundle
for this protocol interface instance.
(3 of 5)
E-76
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
inUseOptionalBw
long
tmnxMcacOperInUseOptnl
Bw
The value of tmnxMcacOperInUseOptnlBw
indicates the operational in-use
bandwidth in kilo-bits per second(kbps)
for the optional channels on the bundle
for this protocol interface instance.
maxBw
long
tmnxMcacOperMaxBw
The value of tmnxMcacOperMaxBw
indicates the operational maximum
bandwidth in kilo-bits per second(kbps)
on the bundle for this protocol interface
instance.
portsDown
long
tmnxMcacOperPortsDown
The value of tmnxMcacOperPortsDown
indicates the the number of ports down on
the application interface. This value is
used to index the table
tmnxMcacLagTable to get the bundle
level id.
valuesInTransit
boolean
tmnxMcacOperValuesInTr
ansit
The value of
tmnxMcacOperValuesInTransit indicates
that the operational (available and in-use
mandatory/optional) value for the
following objects are in transition due to
configuration change:
tmnxMcacOperAvailOptnlBw
tmnxMcacOperAvailMandBw
tmnxMcacOperInUseMandBw
tmnxMcacOperInUseOptnlBw When
Multicast CAC Policy is applied on the
interface for the join of the next channel,
the operational values will be
recalculated and applied to the above
objects and the value for
tmnxMcacOperValuesInTransit will be set
to 'false'. If the value of
tmnxMcacOperValuesInTransit is 'true'
then the values are in transition.
McastCacServOperStats
MIB table name: TIMETRA-MCAST-CAC-MIB.tmnxMcacServOperTable
Monitored class: multicast.McastCacPolicy
activeChannels
long
tmnxMcacServOperActive
Channels
The value of
tmnxMcacServOperActiveChannels
indicates the number of active channels
for this entry.
availMandBw
long
tmnxMcacServOperAvailM
andBw
The value of
tmnxMcacServOperAvailMandBw indicates
the operational pre-reserved bandwidth
in kilo-bits per second(kbps) for the
mandatory channels on the bundle for this
service application on sap/sdp instance.
availOptionalBw
long
tmnxMcacServOperAvailO
ptnlBw
The value of
tmnxMcacServOperAvailOptnlBw
indicates the operational available
bandwidth in kilo-bits per second(kbps)
on the bundle for this service application
on sap/sdp instance.
(4 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-77
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
currConstrtLvl
long
tmnxMcacServOperCurrC
onstrtLvl
The value of
tmnxMcacServOperCurrConstrtLvl
indicates the current lag constraints
bundle level id for the number of ports
down (tmnxMcacServOperPortsDown).
This value is used to index the table
tmnxMcacLevelTable to get the bundle
level bandwidth.
inUseMandBw
long
tmnxMcacServOperInUse
MandBw
The value of
tmnxMcacServOperInUseMandBw
indicates the operational in-use
bandwidth in kilo-bits per second(kbps)
for the mandatory channels on the bundle
for this service application on sap/sdp
instance.
inUseOptionalBw
long
tmnxMcacServOperInUse
OptnlBw
The value of
tmnxMcacServOperInUseOptnlBw
indicates the operational in-use
bandwidth in kilo-bits per second(kbps)
for the optional channels on the bundle
for this service application on sap/sdp
instance.
maxBw
long
tmnxMcacServOperMaxB
w
The value of tmnxMcacServOperMaxBw
indicates the operational maximum
bandwidth in kilo-bits per second(kbps)
on the bundle for this service application
on sap/sdp instance.
portsDown
long
tmnxMcacServOperPortsD
own
The value of
tmnxMcacServOperPortsDown indicates
the the number of ports down on the
service application on sap/sdp. This value
is used to index the table
tmnxMcacLagTable to get the bundle
level id.
valuesInTransit
boolean
tmnxMcacServOperValues
InTransit
The value of
tmnxMcacServOperValuesInTransit
indicates that the operational (available
and in-use mandatory/optional) value for
the following objects are in transition due
to configuration change:
tmnxMcacServOperAvailOptnlBw
tmnxMcacServOperAvailMandBw
tmnxMcacServOperInUseMandBw
tmnxMcacServOperInUseOptnlBw When
Multicast CAC Policy is applied on the
sap/sdp for the join of the next channel,
the operational values will be
recalculated and applied to the above
objects and the value for
tmnxMcacServOperValuesInTransit will be
set to 'false'. If the value of
tmnxMcacServOperValuesInTransit is
'true' then the values are in transition.
(5 of 5)
E-78
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
Table E-19 multichassis statistics
5620 SAM counter name
Type
MIB counter name
Description
MultiChassisPeerRingStats
MIB table name: TIMETRA-MC-REDUNDANCY-MIB.tmnxMcrPeerStatsTable
Monitored class: multichassis.Peer
keepAlivePacketsTransmitted
long
tmnxMcrPeerStatsTxKeep
Alive
The value of
tmnxMcrPeerStatsTxKeepAlive indicates
how many valid MC-Ring control packets
of type 'keepalive' were transmitted to
the peer.
mcsIdRequestPacketsReceived
long
tmnxMcrPeerStatsRxMcsI
dReq
The value of
tmnxMcrPeerStatsRxMcsIdReq indicates
how many valid MCS ID requests were
received from the peer.
mcsIdRequestPacketsTransmitted
long
tmnxMcrPeerStatsTxMcsI
dReq
The value of
tmnxMcrPeerStatsTxMcsIdReq indicates
how many valid MCS ID requests were
transmitted to the peer.
mcsIdResponsePacketsReceived
long
tmnxMcrPeerStatsRxMcsI
dRsp
The value of
tmnxMcrPeerStatsRxMcsIdRsp indicates
how many valid MCS ID responses were
received from the peer.
mcsIdResponsePacketsTransmitted
long
tmnxMcrPeerStatsTxMcsI
dRsp
The value of
tmnxMcrPeerStatsTxMcsIdRsp indicates
how many valid MCS ID responses were
transmitted to the peer.
ringExistsRequestPacketsReceived
long
tmnxMcrPeerStatsRxRing
ExistsReq
The value of
tmnxMcrPeerStatsRxRingExistsReq
indicates how many valid 'ring exists'
requests were received from the peer.
ringExistsRequestPacketsTransmitt
ed
long
tmnxMcrPeerStatsTxRing
ExistsReq
The value of
tmnxMcrPeerStatsTxRingExistsReq
indicates how many valid 'ring exists'
requests were transmitted to the peer.
ringExistsResponsePacketsReceive
d
long
tmnxMcrPeerStatsRxRing
ExistsRsp
The value of
tmnxMcrPeerStatsRxRingExistsRsp
indicates how many valid 'ring exists'
responses were received from the peer.
ringExistsResponsePacketsTransmi
tted
long
tmnxMcrPeerStatsTxRing
ExistsRsp
The value of
tmnxMcrPeerStatsTxRingExistsRsp
indicates how many valid 'ring exists'
responses were transmitted to the peer.
ringKeepAlivePacketsReceived
long
tmnxMcrPeerStatsRxKeep
Alive
The value of
tmnxMcrPeerStatsRxKeepAlive indicates
how many valid MC-Ring control packets
of type 'keepalive' were received from the
peer.
ringSignallingPacketsReceived
long
tmnxMcrPeerStatsRx
The value of tmnxMcrPeerStatsRx
indicates how many valid MC-Ring
signalling messages were received from
the peer.
ringSignallingPacketsTransmitted
long
tmnxMcrPeerStatsTx
The value of tmnxMcrPeerStatsTx
indicates how many valid MC-Ring
signalling messages were transmitted to
the peer.
(1 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-79
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
MultiChassisRingNodeStats
MIB table name: TIMETRA-MC-REDUNDANCY-MIB.tmnxMcrRingNodeStatsTable
Monitored class: multichassis.MultiChassisRingNode
detectedPacketsAcknowledged
long
tmnxMcrRingNodeStatsTx
DetectAck
The value of
tmnxMcrRingNodeStatsTxDetectAck
indicates how many valid 'detected ring
node' signalling messages were
acknowledged to the peer for this
multi-chassis ring node.
detectedPacketsPeerAcknowledge
d
long
tmnxMcrRingNodeStatsRx
DetectAck
The value of
tmnxMcrRingNodeStatsRxDetectAck
indicates how many valid 'detected ring
node' signalling messages were
acknowledged by the peer for this
multi-chassis ring node.
detectedPacketsReceived
long
tmnxMcrRingNodeStatsRx
Detect
The value of
tmnxMcrRingNodeStatsRxDetect indicates
how many valid 'detected ring node'
signalling messages were received from
the peer for this multi-chassis ring node.
detectedPacketsTransmitted
long
tmnxMcrRingNodeStatsTx
Detect
The value of
tmnxMcrRingNodeStatsTxDetect indicates
how many valid 'detected ring node'
signalling messages were transmitted to
the peer for this multi-chassis ring node.
rncvPacketsReceived
long
tmnxMcrRingNodeStatsRn
cvRxResp
The value of
tmnxMcrRingNodeStatsRncvRxResp
indicates how many valid connectivity
verification messages were received from
this multi-chassis ring node.
rncvPacketsRoundTripTime
long
tmnxMcrRingNodeStatsRn
cvRtTime
The value of
tmnxMcrRingNodeStatsRncvRtTime
indicates the round-trip-time of the last
successful connectivity verification for
this multi-chassis ring node. If there has
not been a successful connectivity
verification, the value of
tmnxMcrRingNodeStatsRncvRtTime is
zero.
rncvPacketsTransmitted
long
tmnxMcrRingNodeStatsRn
cvTxReq
The value of
tmnxMcrRingNodeStatsRncvTxReq
indicates how many valid connectivity
verification messages were transmitted to
this multi-chassis ring node.
MultiChassisRingStats
MIB table name: TIMETRA-MC-REDUNDANCY-MIB.tmnxMcrRingStatsTable
Monitored class: multichassis.MultiChassisRing
opaquePacketsReceivedDelivered
long
tmnxMcrRingStatsRxOpaq
ueDelivrd
The value of
tmnxMcrRingStatsRxOpaqueDelivrd
indicates how many valid opaque
signalling messages were received from
the peer and delivered for this
multi-chassis ring.
(2 of 5)
E-80
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
opaquePacketsReceivedNoDestina
tion
long
tmnxMcrRingStatsRxOpaq
ueNoDest
The value of
tmnxMcrRingStatsRxOpaqueNoDest
indicates how many valid opaque
signalling messages were received from
the peer and for which no destination
could be found.
opaquePacketsTransmitted
long
tmnxMcrRingStatsTxOpaq
ue
The value of tmnxMcrRingStatsTxOpaque
indicates how many valid opaque
signalling messages were transmitted to
the peer for this multi-chassis ring.
sapsChangedPacketsReceived
long
tmnxMcrRingStatsRxSaps
Changed
The value of
tmnxMcrRingStatsRxSapsChanged
indicates how many valid 'SAPs changed
info' signalling messages were received
from the peer for this multi-chassis ring.
sapsChangedPacketsTransmitted
long
tmnxMcrRingStatsTxSaps
Changed
The value of
tmnxMcrRingStatsTxSapsChanged
indicates how many valid 'SAPs changed
info' signalling messages were transmitted
to the peer for this multi-chassis ring.
PeerStats
MIB table name: TIMETRA-MC-REDUNDANCY-MIB.tmnxMcLagPeerStatsTable
Monitored class: multichassis.Peer
configPacketsReceived
long
tmnxMcLagPeerStatsPkts
RxConfig
The value of
tmnxMcLagPeerStatsPktsRxConfig
indicates how many valid MC-Lag control
packets of type lag config were received
on this system from the peer.
failedMD5AuthenticationPacketsDr
opped
long
tmnxMcLagPeerStatsDrop
MD5
The value of
tmnxMcLagPeerStatsDropMD5 indicates
how many MC-Lag control packets were
dropped on this system from the peer
because the packet failed MD5
authentication.
failedPacketsTransmitted
long
tmnxMcLagPeerStatsPkts
TxFailed
The value of
tmnxMcLagPeerStatsPktsTxFailed
indicates how many MC-Lag control
packets failed to be transmitted from this
system to the peer.
invalidLagIdPacketsDropped
long
tmnxMcLagPeerStatsDrop
TlvInvldId
The value of
tmnxMcLagPeerStatsDropTlvInvldId
indicates how many MC-Lag control
packets were dropped on this system from
the peer because the packet referred to
an invalid or non multi-chassis lag.
invalidSizePacketsDropped
long
tmnxMcLagPeerStatsDrop
TlvInvldSz
The value of
tmnxMcLagPeerStatsDropTlvInvldSz
indicates how many MC-Lag control
packets were dropped on this system from
the peer because the packet size was
invalid.
keepAlivePacketsReceived
long
tmnxMcLagPeerStatsPkts
RxKpalive
The value of
tmnxMcLagPeerStatsPktsRxKpalive
indicates how many valid MC-Lag control
packets of type keepalive were received
on this system from the peer.
(3 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-81
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
keepalivePacketsTransmitted
long
tmnxMcLagPeerStatsPkts
TxKpalive
The value of
tmnxMcLagPeerStatsPktsTxKpalive
indicates how many MC-Lag control
packets of type keepalive were
transmitted from this system to the peer.
outOfSequencePacketsDropped
long
tmnxMcLagPeerStatsDrop
OutOfSeq
The value of
tmnxMcLagPeerStatsDropOutOfSeq
indicates how many MC-Lag control
packets were dropped on this system from
the peer because the packet was out of
sequence.
packetsReceived
long
tmnxMcLagPeerStatsPkts
Rx
The value of tmnxMcLagPeerStatsPktsRx
indicates how many valid MC-Lag control
packets were received on this system
from the peer.
packetsTransmitted
long
tmnxMcLagPeerStatsPkts
Tx
The value of tmnxMcLagPeerStatsPktsTx
indicates how many MC-Lag control
packets were transmitted from this
system to the peer.
peerConfigPacketsReceived
long
tmnxMcLagPeerStatsPkts
RxPeerCfg
The value of
tmnxMcLagPeerStatsPktsRxPeerCfg
indicates how many valid MC-Lag control
packets of type peer config were received
on this system from the peer.
peerConfigPacketsTransmitted
long
tmnxMcLagPeerStatsPkts
TxPeerCfg
The value of
tmnxMcLagPeerStatsPktsTxPeerCfg
indicates how many MC-Lag control
packets of type peer config were
transmitted from this system to the peer.
stateDisabledPacketsDropped
long
tmnxMcLagPeerStatsDrop
StateDsbld
The value of
tmnxMcLagPeerStatsDropStateDsbld
indicates how many MC-Lag control
packets were dropped on this system from
the peer because the peer was
administratively disabled.
statePacketsReceived
long
tmnxMcLagPeerStatsPkts
RxState
The value of
tmnxMcLagPeerStatsPktsRxState
indicates how many valid MC-Lag control
packets of type lag state were received on
this system from the peer.
tooShortPacketsDropped
long
tmnxMcLagPeerStatsDrop
PktTooShrt
The value of
tmnxMcLagPeerStatsDropPktTooShrt
indicates how many MC-Lag control
packets were dropped on this system from
the peer because the packet was too
short.
unknownTlvPacketsDropped
long
tmnxMcLagPeerStatsDrop
UnknownTlv
The value of
tmnxMcLagPeerStatsDropUnknownTlv
indicates how many MC-Lag control
packets were dropped on this system from
the peer because the packet contained an
unknown TLV.
PeerSynchronizationProtocolStats
MIB table name: TIMETRA-MC-REDUNDANCY-MIB.tmnxMcPeerSyncStatsTable
Monitored class: multichassis.PeerSynchronizationProtocol
(4 of 5)
E-82
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
bodyDecodeErrorPacketsReceived
long
tmnxMcPeerSyncPktsRxEr
rBody
The value of
tmnxMcPeerSyncPktsRxErrBody indicates
the number of packets with body decode
errors received from the multi-chassis
peer.
dataPacketsReceived
long
tmnxMcPeerSyncPktsRxD
ata
The value of tmnxMcPeerSyncPktsRxData
indicates the number of hello packets
received from the multi-chassis peer.
dataPacketsTransmitted
long
tmnxMcPeerSyncPktsTxD
ata
The value of tmnxMcPeerSyncPktsTxData
indicates the number of data packets
transmitted to the multi-chassis peer.
erroneousPacketsReceived
long
tmnxMcPeerSyncPktsRxEr
r
The value of tmnxMcPeerSyncPktsRxErr
indicates the number of erroneous
packets received from the multi-chassis
peer.
headerDecodeErrorPacketsReceive
d
long
tmnxMcPeerSyncPktsRxEr
rHeader
The value of
tmnxMcPeerSyncPktsRxErrHeader
indicates the number of packets with
header decode errors received from the
multi-chassis peer.
helloPacketsReceived
long
tmnxMcPeerSyncPktsRxH
ello
The value of tmnxMcPeerSyncPktsRxHello
indicates the number of hello packets
received from the multi-chassis peer.
helloPacketsTransmitted
long
tmnxMcPeerSyncPktsTxH
ello
The value of tmnxMcPeerSyncPktsTxHello
indicates the number of hello packets
transmitted to the multi-chassis peer.
otherPacketsReceived
long
tmnxMcPeerSyncPktsRxOt
her
The value of
tmnxMcPeerSyncPktsRxOther indicates
the number of all other packet types
received from the multi-chassis peer.
otherPacketsTransmitted
long
tmnxMcPeerSyncPktsTxOt
her
The value of
tmnxMcPeerSyncPktsTxOther indicates
the number of all other packet types
transmitted to the multi-chassis peer.
packetTransmissionErrors
long
tmnxMcPeerSyncPktsTxEr
r
The value of tmnxMcPeerSyncPktsTxErr
indicates the number of packet
transmission errors.
sequenceNumberErrorPacketsRece
ived
long
tmnxMcPeerSyncPktsRxEr
rSeqNum
The value of
tmnxMcPeerSyncPktsRxErrSeqNum
indicates the number of packets with
sequence number errors received from
the multi-chassis peer.
totalPacketsReceived
long
tmnxMcPeerSyncPktsRxAl
l
The value of tmnxMcPeerSyncPktsRxAll
indicates the total number of packets
received from the multi-chassis peer.
totalPacketsTransmitted
long
tmnxMcPeerSyncPktsTxAl
l
The value of tmnxMcPeerSyncPktsTxAll
indicates the total number of packets
transmitted to the multi-chassis peer.
(5 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-83
E. 7450 ESS Release 7.0 statistics counters
Table E-20 ospf statistics
5620 SAM counter name
Type
MIB counter name
Description
AreaBasicStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfAreaTable
Monitored class: ospf.AreaSite
nssaTranslatorEvents
long
tmnxOspfAreaNssaTransl
atorEvents
The value of
tmnxOspfAreaNssaTranslatorEvents
indicates the number of Translator State
changes that have occurred since the last
boot-up.
totalLSACount
long
tmnxOspfAreaScopeLsaCo
unt
The value of tmnxOspfAreaScopeLsaCount
indicates the total number of Area-Scope
link state advertisements in this area's
link-state database.
totalSpfRuns
long
tmnxOspfAreaSpfRuns
The value of tmnxOspfAreaSpfRuns
indicates the number of times that the
intra-area route table has been
calculated using this area's link-state
database. This is typically done using
Dijkstra's algorithm.
totalUnknownLSACount
long
tmnxOspfAreaScopeUnkLs
aCount
The value of
tmnxOspfAreaScopeUnkLsaCount
indicates the total number of unknown
Area-Scope link-state advertisements in
this area's link-state database.
InterfaceGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
events
long
tmnxOspfIfEvents
The value of tmnxOspfIfEvents indicates
the number of times this OSPF interface
has changed its state, or an error has
occurred.
InterfaceReceiveStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
databaseDescriptionPackets
long
tmnxOspfIfRxDBDs
The value of tmnxOspfIfRxDBDs indicates
the total number of OSPF Database
Description packets received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
databaseDescriptionPackets
long
tmnxOspfIfTxDBDs
The value of tmnxOspfIfTxDBDs indicates
the total number of OSPF Database
Description packets transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
helloPackets
long
tmnxOspfIfRxHellos
The value of tmnxOspfIfRxHellos indicates
the total number of OSPF Hello packets
received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
(1 of 12)
E-84
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
helloPackets
long
tmnxOspfIfTxHellos
The value of tmnxOspfIfTxHellos indicates
the total number of OSPF Hello packets
transmitted on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfRxLSAcks
The value of tmnxOspfIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfTxLSAcks
The value of tmnxOspfIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this interface since tmnxOspfAdminState
was last set to 'enabled'.
linkStateRequests
long
tmnxOspfIfRxLSRs
The value of tmnxOspfIfRxLSRs indicates
the total number of Link State Requests
(LSRs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateRequests
long
tmnxOspfIfTxLSRs
The value of tmnxOspfIfTxLSRs indicates
the total number of OSPF Link State
Requests (LSRs)transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateUpdates
long
tmnxOspfIfRxLSUs
The value of tmnxOspfIfRxLSUs indicates
the total number of Link State Updates
(LSUs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateUpdates
long
tmnxOspfIfTxLSUs
The value of tmnxOspfIfTxLSUs indicates
the total number of OSPF Link State
Updates (LSUs) transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
lsasWithBadChecksums
long
tmnxOspfIfRxBadChecksu
ms
The value of tmnxOspfIfRxBadChecksums
indicates the count of LSAs received with
bad checksums.
totalPackets
long
tmnxOspfIfRxPackets
The value of tmnxOspfIfRxPackets
indicates the total number of OSPF
packets received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
totalPackets
long
tmnxOspfIfTxPackets
The value of tmnxOspfIfTxPackets
indicates the total number of OSPF
packets transmitted on this interface
since tmnxOspfAdminState was last set to
'enabled'.
InterfaceStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
(2 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-85
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
authorizationFailures
long
tmnxOspfIfAuthFailures
The value of tmnxOspfIfAuthFailures
indicates the total number of OSPF
packets received with an invalid
authorization key since
tmnxOspfAdminState was last set to
'enabled'.
badAreas
long
tmnxOspfIfBadAreas
The value of tmnxOspfIfBadAreas
indicates the total number of OSPF
packets received with an area mismatch
since tmnxOspfAdminState was last set to
'enabled'.
badAuthorizationTypes
long
tmnxOspfIfBadAuthTypes
The value of tmnxOspfIfBadAuthTypes
indicates the total number of OSPF
packets received with an invalid
authorization type since
tmnxOspfAdminState was last set to
'enabled'.
badDeadIntervals
long
tmnxOspfIfBadDeadInterv
als
The value of tmnxOspfIfBadDeadIntervals
indicates the total number of OSPF
packets received where the dead interval
given in the packet was not equal to that
configured on this interface since
tmnxOspfAdminState was last set to
'enabled'.
badDestinationAddresses
long
tmnxOspfIfBadDstAddrs
The value of tmnxOspfIfBadDstAddrs
indicates the total number of OSPF
packets received with the incorrect IP
destination address since
tmnxOspfAdminState was last set to
'enabled'.
badHelloIntervals
long
tmnxOspfIfBadHelloInterv
als
The value of tmnxOspfIfBadHelloIntervals
indicates the total number of OSPF
packets received where the hello interval
given in packet was not equal to that
configured on this interface since
tmnxOspfAdminState was last set to
'enabled'.
badLengths
long
tmnxOspfIfBadLengths
The value of tmnxOspfIfBadLengths
indicates the total number of OSPF
packets received on this interface with a
total length not equal to the length given
in the packet itself since
tmnxOspfAdminState was last set to
'enabled'.
badNeighbors
long
tmnxOspfIfBadNeighbors
The value of tmnxOspfIfBadNeighbors
indicates the total number of OSPF
packets received where the neighbor
information does not match the
information this router has for the
neighbor since tmnxOspfAdminState was
last set to 'enabled'.
badNetworks
long
tmnxOspfIfBadNetworks
The value of tmnxOspfIfBadNetworks
indicates the total number of OSPF
packets received with invalid network or
mask since tmnxOspfAdminState was last
set to 'enabled'.
(3 of 12)
E-86
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badOptions
long
tmnxOspfIfBadOptions
The value of tmnxOspfIfBadOptions
indicates the total number of OSPF
packets received with an option that does
not match those configured for this
interface or area since
tmnxOspfAdminState was last set to
'enabled'.
badPacketTypes
long
tmnxOspfIfBadPacketTyp
es
The value of tmnxOspfIfBadPacketTypes
indicates the total number of OSPF
packets received with an invalid OSPF
packet type since tmnxOspfAdminState
was last set to 'enabled'.
badVersions
long
tmnxOspfIfBadVersions
The value of tmnxOspfIfBadVersions
indicates the total number of OSPF
packets received with bad OSPF version
numbers since tmnxOspfAdminState was
last set to 'enabled'.
badVirtualLinks
long
tmnxOspfIfBadVirtualLink
s
The value of tmnxOspfIfBadVirtualLinks
indicates the total number of OSPF
packets received on this interface that
are destined to a virtual link that does not
exist since tmnxOspfAdminState was last
set to 'enabled'.
discardPackets
long
tmnxOspfIfDiscardPacket
s
The value of tmnxOspfIfDiscardPackets
indicates the total number of OSPF
packets discarded on this interface since
tmnxOspfAdminState was last set to
'enabled'.
retransmitOuts
long
tmnxOspfIfRetransmitOut
s
The value of tmnxOspfIfRetransmitOuts
indicates the total number of OSPF
Retransmits sent on this interface since
tmnxOspfAdminState was last set to
'enabled'.
InterfaceTransmitStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
databaseDescriptionPackets
long
tmnxOspfIfRxDBDs
The value of tmnxOspfIfRxDBDs indicates
the total number of OSPF Database
Description packets received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
databaseDescriptionPackets
long
tmnxOspfIfTxDBDs
The value of tmnxOspfIfTxDBDs indicates
the total number of OSPF Database
Description packets transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
helloPackets
long
tmnxOspfIfRxHellos
The value of tmnxOspfIfRxHellos indicates
the total number of OSPF Hello packets
received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
helloPackets
long
tmnxOspfIfTxHellos
The value of tmnxOspfIfTxHellos indicates
the total number of OSPF Hello packets
transmitted on this interface since
tmnxOspfAdminState was last set to
'enabled'.
(4 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-87
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
linkStateAcknowledgements
long
tmnxOspfIfRxLSAcks
The value of tmnxOspfIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfTxLSAcks
The value of tmnxOspfIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this interface since tmnxOspfAdminState
was last set to 'enabled'.
linkStateRequests
long
tmnxOspfIfRxLSRs
The value of tmnxOspfIfRxLSRs indicates
the total number of Link State Requests
(LSRs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateRequests
long
tmnxOspfIfTxLSRs
The value of tmnxOspfIfTxLSRs indicates
the total number of OSPF Link State
Requests (LSRs)transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateUpdates
long
tmnxOspfIfRxLSUs
The value of tmnxOspfIfRxLSUs indicates
the total number of Link State Updates
(LSUs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateUpdates
long
tmnxOspfIfTxLSUs
The value of tmnxOspfIfTxLSUs indicates
the total number of OSPF Link State
Updates (LSUs) transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
totalPackets
long
tmnxOspfIfRxPackets
The value of tmnxOspfIfRxPackets
indicates the total number of OSPF
packets received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
totalPackets
long
tmnxOspfIfTxPackets
The value of tmnxOspfIfTxPackets
indicates the total number of OSPF
packets transmitted on this interface
since tmnxOspfAdminState was last set to
'enabled'.
NeighborGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfNbrStatsTable
Monitored class: ospf.Neighbor
events
long
tmnxOspfNbrEvents
The value of tmnxOspfNbrEvents
indicates the number of times this
neighbor relationship has changed state,
or an error has occurred.
retransmissionQueueLength
long
tmnxOspfNbrLsRetransQL
en
The value of tmnxOspfNbrLsRetransQLen
indicates the current length of the
retransmission queue.
NeighborStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfNbrStatsTable
Monitored class: ospf.Neighbor
(5 of 12)
E-88
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badMtus
long
tmnxOspfNbrBadMTUs
The value of tmnxOspfNbrBadMTUs
indicates the total number of times when
the MTU in a received database
description packet was larger than the
MTU of the receiving interface since
tmnxOspfAdminState was last set to
'enabled'.
badNeighborStates
long
tmnxOspfNbrBadNbrState
s
The value of tmnxOspfNbrBadNbrStates
indicates the total number of OSPF
packets received when the neighbor state
was not expecting to receive this packet
type since tmnxOspfAdminState was last
set to 'enabled'.
badPackets
long
tmnxOspfNbrBadPackets
The value of tmnxOspfNbrBadPackets
indicates the total number of times when
an LS update was received with an illegal
LS type or an option mismatch since
tmnxOspfAdminState was last set to
'enabled'.
badSequenceNumbers
long
tmnxOspfNbrBadSeqNums
The value of tmnxOspfNbrBadSeqNums
indicates the total number of times when
a database description packet was
received with a sequence number
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
duplicates
long
tmnxOspfNbrDuplicates
The value of tmnxOspfNbrDuplicates
indicates the total number of times when
a duplicate database description packet
was received during the Exchange state
since tmnxOspfAdminState was last set to
'enabled'.
lsaInstallFailed
long
tmnxOspfNbrLsaInstallFai
led
The value of tmnxOspfNbrLsaInstallFailed
indicates the total number of times an
LSA could not be installed into the LSDB
due to a resource allocation issue since
tmnxOspfAdminState was last set to
'enabled'.
lsaNotInLSDB
long
tmnxOspfNbrLsaNotInLsd
bs
The value of tmnxOspfNbrLsaNotInLsdbs
indicates the total number of times when
an LS request was received for an LSA not
installed in the LSDB of this router since
tmnxOspfAdminState was last set to
'enabled'.
numberOfRestarts
long
tmnxOspfNbrNumRestarts
The value of tmnxOspfNbrNumRestarts
indicates the number of times the
neighbor has attempted restart.
optionMismatches
long
tmnxOspfNbrOptionMism
atches
The value of
tmnxOspfNbrOptionMismatches indicates
the total number of times when a LS
update was received with an option
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
SiteStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfStatisticsTable
Monitored class: ospf.Site
(6 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-89
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
addRouteFailed
long
tmnxOspfRoutesAddsFail
ed
The value of tmnxOspfRoutesAddsFailed
indicates the number of times an attempt
to add a route to the Route Table Manager
(RTM) failed for this OSPF instance.
cspfDroppedRequests
long
tmnxOspfCSPFDroppedRe
quests
The value of
tmnxOspfCSPFDroppedRequests indicates
the number of dropped CSPF requests
made by the OSPF protocol.
cspfPathsFound
long
tmnxOspfCSPFPathsFoun
d
The value of tmnxOspfCSPFPathsFound
indicates the number of of paths found for
the requests made to OSPF protocol.
cspfPathsNotFound
long
tmnxOspfCSPFPathsNotFo
und
The value of
tmnxOspfCSPFPathsNotFound indicates
the number of of paths not found for the
requests made to OSPF protocol.
cspfRequests
long
tmnxOspfCSPFRequests
The value of tmnxOspfCSPFRequests
indicates the number of CSPF requests
made to the OSPF protocol.
deleteRouteFailed
long
tmnxOspfRoutesDelsFaile
d
The value of tmnxOspfRoutesDelsFailed
indicates the number of times an attempt
to delete a route from the Route Table
Manager (RTM) failed for this instance of
OSPF.
inOverflowCount
long
tmnxOspfNumTimesInOve
rflow
The value of
tmnxOspfNumTimesInOverflow indicates
the count of the number of times the
system was in the overflow state.
inOverloadCount
long
tmnxOspfNumTimesInOve
rload
The value of
tmnxOspfNumTimesInOverload indicates
the count of the number of times the
system was overloaded.
modifyRouteFailed
long
tmnxOspfRoutesModsFail
ed
The value of tmnxOspfRoutesModsFailed
indicates the number of times an attempt
to modify a route in the Route Table
Manager (RTM) failed for this instance of
OSPF.
newLsasOriginated
long
tmnxOspfOriginateNewLs
as
The value of tmnxOspfOriginateNewLsas
indicates the number of new link-state
advertisements that have been
originated. This number is incremented
each time the router originates a new
LSA.
newLsasReceived
long
tmnxOspfRxNewLsas
The value of tmnxOspfRxNewLsas
indicates the number of link-state
advertisements received determined to
be new instantiations. This number does
not include newer instantiations of
self-originated link-state advertisements.
spfAttemptsFailed
long
tmnxOspfSpfAttemptsFail
ed
The value of tmnxOspfSpfAttemptsFailed
indicates the number of times an attempt
to run SPF has failed because SPF runs
have been stopped as a result of
insufficient memory resources.
(7 of 12)
E-90
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
VirtualLinkGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
events
long
tmnxOspfVirtIfEvents
The value of tmnxOspfVirtIfEvents
indicates the number of state changes or
error events on this Virtual Link.
VirtualLinkReceiveStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
databaseDescriptionPackets
long
tmnxOspfVirtIfRxDBDs
The value of tmnxOspfVirtIfRxDBDs
indicates the total number of OSPF
Database Description packets received on
this virtual interface.
databaseDescriptionPackets
long
tmnxOspfVirtIfTxDBDs
The value of tmnxOspfVirtIfTxDBDs
indicates the total number of OSPF
Database Description packets transmitted
on this virtual interface.
helloPackets
long
tmnxOspfVirtIfRxHellos
The value of tmnxOspfVirtIfRxHellos
indicates the total number of OSPF Hello
packets received on this virtual interface.
helloPackets
long
tmnxOspfVirtIfTxHellos
The value of tmnxOspfVirtIfTxHellos
indicates the total number of OSPF Hello
packets transmitted on this virtual
interface since it was created.
linkStateAcknowledgements
long
tmnxOspfVirtIfRxLSAcks
The value of tmnxOspfVirtIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
virtual interface.
linkStateAcknowledgements
long
tmnxOspfVirtIfTxLSAcks
The value of tmnxOspfVirtIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this virtual interface.
linkStateRequests
long
tmnxOspfVirtIfRxLSRs
The value of tmnxOspfVirtIfRxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) received on this
virtual interface.
linkStateRequests
long
tmnxOspfVirtIfTxLSRs
The value of tmnxOspfVirtIfTxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) transmitted on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfRxLSUs
The value of tmnxOspfVirtIfRxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) received on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfTxLSUs
The value of tmnxOspfVirtIfTxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) transmitted on this
virtual interface.
lsasWithBadChecksums
long
tmnxOspfVirtIfRxBadChec
ksums
The value of
tmnxOspfVirtIfRxBadChecksums indicates
the count of LSAs received with bad
checksums.
(8 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-91
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalPackets
long
tmnxOspfVirtIfRxPackets
The value of tmnxOspfVirtIfRxPackets
indicates the total number of OSPF
packets received on this virtual interface
since it was created.
totalPackets
long
tmnxOspfVirtIfTxPackets
The value of tmnxOspfVirtIfTxPackets
indicates the total number of OSPF
packets transmitted on this virtual
interface since it was created.
VirtualLinkStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
authorizationFailures
long
tmnxOspfVirtIfAuthFailur
es
The value of tmnxOspfVirtIfAuthFailures
indicates the total number of OSPF
packets received on this virtual interface
with invalid authentication keys.
badAreas
long
tmnxOspfVirtIfBadAreas
The value of tmnxOspfVirtIfBadAreas
indicates the total number of OSPF
packets received on this virtual interface
with area mismatches.
badAuthorizationTypes
long
tmnxOspfVirtIfBadAuthTy
pes
The value of tmnxOspfVirtIfBadAuthTypes
indicates the total number of OSPF
packets received on this virtual interface
with invalid authentication types.
badDeadIntervals
long
tmnxOspfVirtIfBadDeadIn
tervals
The value of
tmnxOspfVirtIfBadDeadIntervals indicates
the total number of OSPF packets
received where the dead interval given in
the packet was not equal to that
configured on this virtual interface since
tmnxOspfAdminState was last set to
'enabled'.
badDestinationAddresses
long
tmnxOspfVirtIfBadDstAdd
rs
The value of tmnxOspfVirtIfBadDstAddrs
indicates the total number of OSPF
packets received on this virtual interface
with invalid destination IP address.
badHelloIntervals
long
tmnxOspfVirtIfBadHelloIn
tervls
The value of
tmnxOspfVirtIfBadHelloIntervls indicates
the total number of OSPF packets
received where the hello interval given in
packet was not equal to that configured
on this virtual interface since
tmnxOspfAdminState was last set to
'enabled'.
badLengths
long
tmnxOspfVirtIfBadLength
s
The value of tmnxOspfVirtIfBadLengths
indicates the total number of OSPF
packets received on this virtual interface
with a total length not equal to the length
given in the packet itself since
tmnxOspfAdminState was last set to
'enabled'.
badNeighbors
long
tmnxOspfVirtIfBadNeighb
ors
The value of tmnxOspfVirtIfBadNeighbors
indicates the total number of OSPF
packets received where the neighbor
information does not match the
configuration this router has for the
neighbor.
(9 of 12)
E-92
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badNetworks
long
tmnxOspfVirtIfBadNetwor
ks
The value of tmnxOspfVirtIfBadNetworks
indicates the total number of OSPF
packets received on this virtual interface
with invalid network or mask fields.
badOptions
long
tmnxOspfVirtIfBadOption
s
The value of tmnxOspfVirtIfBadOptions
indicates the total number of OSPF
packets received with an option that does
not match those configured for this
virtual interface or transit-area since
tmnxOspfAdminState was last set to
'enabled'.
badPacketTypes
long
tmnxOspfVirtIfBadPacket
Types
The value of
tmnxOspfVirtIfBadPacketTypes indicates
the total number of OSPF packets
received on this virtual interface with
invalid OSPF packet types.
badVersions
long
tmnxOspfVirtIfBadVersion
s
The value of tmnxOspfVirtIfBadVersions
indicates the total number of OSPF
packets received on this virtual interface
with invalid OSPF version numbers.
discardPackets
long
tmnxOspfVirtIfDiscardPac
kets
The value of
tmnxOspfVirtIfDiscardPackets indicates
the total number of OSPF packets
discarded on this virtual interface.
retransmitOuts
long
tmnxOspfVirtIfRetransmit
Outs
The value of
tmnxOspfVirtIfRetransmitOuts indicates
the total number of OSPF packets
retransmitted on this virtual interface.
VirtualLinkTransmitStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtIfStatsTable
Monitored class: ospf.VirtualLink
databaseDescriptionPackets
long
tmnxOspfVirtIfRxDBDs
The value of tmnxOspfVirtIfRxDBDs
indicates the total number of OSPF
Database Description packets received on
this virtual interface.
databaseDescriptionPackets
long
tmnxOspfVirtIfTxDBDs
The value of tmnxOspfVirtIfTxDBDs
indicates the total number of OSPF
Database Description packets transmitted
on this virtual interface.
helloPackets
long
tmnxOspfVirtIfRxHellos
The value of tmnxOspfVirtIfRxHellos
indicates the total number of OSPF Hello
packets received on this virtual interface.
helloPackets
long
tmnxOspfVirtIfTxHellos
The value of tmnxOspfVirtIfTxHellos
indicates the total number of OSPF Hello
packets transmitted on this virtual
interface since it was created.
linkStateAcknowledgements
long
tmnxOspfVirtIfRxLSAcks
The value of tmnxOspfVirtIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
virtual interface.
linkStateAcknowledgements
long
tmnxOspfVirtIfTxLSAcks
The value of tmnxOspfVirtIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this virtual interface.
(10 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-93
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
linkStateRequests
long
tmnxOspfVirtIfRxLSRs
The value of tmnxOspfVirtIfRxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) received on this
virtual interface.
linkStateRequests
long
tmnxOspfVirtIfTxLSRs
The value of tmnxOspfVirtIfTxLSRs
indicates the total number of OSPF Link
State Requests (LSRs) transmitted on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfRxLSUs
The value of tmnxOspfVirtIfRxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) received on this
virtual interface.
linkStateUpdates
long
tmnxOspfVirtIfTxLSUs
The value of tmnxOspfVirtIfTxLSUs
indicates the total number of OSPF Link
State Updates (LSUs) transmitted on this
virtual interface.
totalPackets
long
tmnxOspfVirtIfRxPackets
The value of tmnxOspfVirtIfRxPackets
indicates the total number of OSPF
packets received on this virtual interface
since it was created.
totalPackets
long
tmnxOspfVirtIfTxPackets
The value of tmnxOspfVirtIfTxPackets
indicates the total number of OSPF
packets transmitted on this virtual
interface since it was created.
VirtualNeighborGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtNbrStatsTable
Monitored class: ospf.VirtualNeighbor
events
long
tmnxOspfVirtNbrEvents
The value of tmnxOspfVirtNbrEvents
indicates the number of times this virtual
link has changed its state, or an error has
occurred.
retransmissionQueueLength
long
tmnxOspfVirtNbrLsRetran
sQLen
The value of
tmnxOspfVirtNbrLsRetransQLen indicates
the current length of the retransmission
queue.
VirtualNeighborStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfVirtNbrStatsTable
Monitored class: ospf.VirtualNeighbor
badMtus
long
tmnxOspfVirtNbrBadMTUs
The value of tmnxOspfVirtNbrBadMTUs
indicates the total number of times when
the MTU in a received database
description packet was larger than the
MTU of the receiving interface since
tmnxOspfAdminState was last set to
'enabled'.
badPackets
long
tmnxOspfVirtNbrBadPack
ets
The value of tmnxOspfVirtNbrBadPackets
indicates the total number of times when
an LS update was received with an illegal
LS type or an option mismatch since
tmnxOspfAdminState was last set to
'enabled'.
(11 of 12)
E-94
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badSequenceNumbers
long
tmnxOspfVirtNbrBadSeqN
ums
The value of
tmnxOspfVirtNbrBadSeqNums indicates
the total number of times when a
database description packet was received
with a sequence number mismatch since
tmnxOspfAdminState was last set to
'enabled'.
badVirtualNeighborStates
long
tmnxOspfVirtNbrBadNbrS
tates
The value of
tmnxOspfVirtNbrBadNbrStates indicates
the total number of OSPF packets
received when the virtual neighbor state
was not expecting to receive this packet
type since tmnxOspfAdminState was last
set to 'enabled'.
duplicates
long
tmnxOspfVirtNbrDuplicat
es
The value of tmnxOspfVirtNbrDuplicates
indicates the total number of times when
a duplicate database description packet
was received during the Exchange state
since tmnxOspfAdminState was last set to
'enabled'.
lsaInstallFailed
long
tmnxOspfVirtNbrLsaInstal
lFail
The value of
tmnxOspfVirtNbrLsaInstallFail indicates
the total number of times when an LSA
could not be installed into the LSDB due to
a resource allocation issue since
tmnxOspfAdminState was last set to
'enabled'.
lsaNotInLSDB
long
tmnxOspfVirtNbrLsaNotIn
Lsdbs
The value of
tmnxOspfVirtNbrLsaNotInLsdbs indicates
the total number of times when an LS
request was received for an LSA not
installed in the LSDB of this router since
tmnxOspfAdminState was last set to
'enabled'.
numberOfRestarts
long
tmnxOspfVirtNbrNumRest
arts
The value of
tmnxOspfVirtNbrNumRestarts indicates
the number of times the virtual neighbor
has attempted restart since
tmnxOspfAdminState was last set to
'enabled'.
optionMismatches
long
tmnxOspfVirtNbrOptionMi
smatch
The value of
tmnxOspfVirtNbrOptionMismatch
indicates the total number of times when
a LS update was received with an option
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
(12 of 12)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-95
E. 7450 ESS Release 7.0 statistics counters
Table E-21 pae802_1x statistics
5620 SAM counter name
Type
MIB counter name
Description
PaePortAuthenticatorDiagStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthDiagTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dot1xAuthAuthEapLogoffWhileAut
henticated
long
dot1xAuthAuthEapLogoff
WhileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to DISCONNECTED, as a
result of an EAPOL-Logoff message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.12.
dot1xAuthAuthEapLogoffWhileAut
henticating
long
dot1xAuthAuthEapLogoff
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of an EAPOL-Logoff message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.9.
dot1xAuthAuthEapStartsWhileAuth
enticated
long
dot1xAuthAuthEapStarts
WhileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to CONNECTING, as a
result of an EAPOL-Start message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.11.
dot1xAuthAuthEapStartsWhileAuth
enticating
long
dot1xAuthAuthEapStarts
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of an EAPOL-Start message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.8.
dot1xAuthAuthFailWhileAuthentic
ating
long
dot1xAuthAuthFailWhileA
uthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to HELD, as a result of
the Backend Authentication state
machine indicating authentication failure
(authFail = TRUE). REFERENCE 9.4.2,
8.5.4.2.6.
dot1xAuthAuthReauthsWhileAuthe
nticated
long
dot1xAuthAuthReauthsW
hileAuthenticated
Counts the number of times that the state
machine transitions from
AUTHENTICATED to CONNECTING, as a
result of a reauthentication request
(reAuthenticate = TRUE). REFERENCE
9.4.2, 8.5.4.2.10.
dot1xAuthAuthReauthsWhileAuthe
nticating
long
dot1xAuthAuthReauthsW
hileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of a reauthentication request
(reAuthenticate = TRUE). REFERENCE
9.4.2, 8.5.4.2.7.
(1 of 4)
E-96
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthAuthSuccessWhileAuthe
nticating
long
dot1xAuthAuthSuccessWh
ileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to AUTHENTICATED, as
a result of the Backend Authentication
state machine indicating successful
authentication of the Supplicant
(authSuccess = TRUE). REFERENCE 9.4.2,
8.5.4.2.4.
dot1xAuthAuthTimeoutsWhileAuth
enticating
long
dot1xAuthAuthTimeouts
WhileAuthenticating
Counts the number of times that the state
machine transitions from
AUTHENTICATING to ABORTING, as a
result of the Backend Authentication
state machine indicating authentication
timeout (authTimeout = TRUE).
REFERENCE 9.4.2, 8.5.4.2.5.
dot1xAuthBackendAccessChalleng
es
long
dot1xAuthBackendAccess
Challenges
Counts the number of times that the state
machine receives an initial
Access-Challenge packet from the
Authentication server (i.e., aReq
becomes TRUE, causing exit from the
RESPONSE state). Indicates that the
Authentication Server has communication
with the Authenticator. REFERENCE 9.4.2,
8.5.6.2.2.
dot1xAuthBackendAuthFails
long
dot1xAuthBackendAuthFa
ils
Counts the number of times that the state
machine receives an EAP-Failure message
from the Authentication Server (i.e., aFail
becomes TRUE, causing a transition from
RESPONSE to FAIL). Indicates that the
Supplicant has not authenticated to the
Authentication Server. REFERENCE 9.4.2,
8.5.6.2.6.
dot1xAuthBackendAuthSuccesses
long
dot1xAuthBackendAuthSu
ccesses
Counts the number of times that the state
machine receives an EAP-Success message
from the Authentication Server (i.e.,
aSuccess becomes TRUE, causing a
transition from RESPONSE to SUCCESS).
Indicates that the Supplicant has
successfully authenticated to the
Authentication Server. REFERENCE 9.4.2,
8.5.6.2.5.
dot1xAuthBackendNonNakRespons
esFromSupplicant
long
dot1xAuthBackendNonNa
kResponsesFromSupplica
nt
Counts the number of times that the state
machine receives a response from the
Supplicant to an initial EAP-Request, and
the response is something other than
EAP-NAK (i.e., rxResp becomes TRUE,
causing the state machine to transition
from REQUEST to RESPONSE, and the
response is not an EAP-NAK). Indicates
that the Supplicant can respond to the
Authenticator's chosen EAP-method.
REFERENCE 9.4.2, 8.5.6.2.4.
dot1xAuthBackendOtherRequestsT
oSupplicant
long
dot1xAuthBackendOtherR
equestsToSupplicant
Counts the number of times that the state
machine sends an EAP-Request packet
(other than an Identity, Notification,
Failure or Success message) to the
Supplicant (i.e., executes txReq on entry
to the REQUEST state). Indicates that the
Authenticator chose an EAP-method.
REFERENCE 9.4.2, 8.5.6.2.3.
(2 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-97
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
dot1xAuthBackendResponses
long
dot1xAuthBackendRespon
ses
Counts the number of times that the state
machine sends an initial Access-Request
packet to the Authentication server (i.e.,
executes sendRespToServer on entry to
the RESPONSE state). Indicates that the
Authenticator attempted communication
with the Authentication Server.
REFERENCE 9.4.2, 8.5.6.2.1.
dot1xAuthEapLogoffsWhileConnec
ting
long
dot1xAuthEapLogoffsWhil
eConnecting
Counts the number of times that the state
machine transitions from CONNECTING to
DISCONNECTED as a result of receiving an
EAPOL-Logoff message. REFERENCE 9.4.2,
8.5.4.2.2.
dot1xAuthEntersAuthenticating
long
dot1xAuthEntersAuthenti
cating
Counts the number of times that the state
machine transitions from CONNECTING to
AUTHENTICATING, as a result of an
EAP-Response/Identity message being
received from the Supplicant. REFERENCE
9.4.2, 8.5.4.2.3.
dot1xAuthEntersConnecting
long
dot1xAuthEntersConnecti
ng
Counts the number of times that the state
machine transitions to the CONNECTING
state from any other state. REFERENCE
9.4.2, 8.5.4.2.1.
PaePortAuthenticatorSessionStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthSessionStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
dot1xAuthSessionAuthenticMethod
int
dot1xAuthSessionAuthent
icMethod
The authentication method used to
establish the session. REFERENCE 9.4.4,
Session Authentication Method.
dot1xAuthSessionFramesRx
long
dot1xAuthSessionFrames
Rx
The number of user data frames received
on this Port during the session.
REFERENCE 9.4.4, Session Frames
Received.
dot1xAuthSessionFramesTx
long
dot1xAuthSessionFrames
Tx
The number of user data frames
transmitted on this Port during the
session. REFERENCE 9.4.4, Session Frames
Transmitted.
dot1xAuthSessionOctetsRx
UINT128
dot1xAuthSessionOctetsR
x
The number of octets received in user
data frames on this Port during the
session. REFERENCE 9.4.4, Session Octets
Received.
dot1xAuthSessionOctetsTx
UINT128
dot1xAuthSessionOctetsT
x
The number of octets transmitted in user
data frames on this Port during the
session. REFERENCE 9.4.4, Session Octets
Transmitted.
dot1xAuthSessionTerminateCause
int
dot1xAuthSessionTermina
teCause
The reason for the session termination.
REFERENCE 9.4.4, Session Terminate
Cause.
dot1xAuthSessionTime
long
dot1xAuthSessionTime
The duration of the session in seconds.
REFERENCE 9.4.4, Session Time.
(3 of 4)
E-98
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
PaePortAuthenticatorStats
MIB table name: IEEE8021-PAE-MIB.dot1xAuthStatsTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
dot1xAuthEapLengthErrorFramesR
x
long
dot1xAuthEapLengthError
FramesRx
The number of EAPOL frames that have
been received by this Authenticator in
which the Packet Body Length field is
invalid. REFERENCE 9.4.2, EAP length
error frames received.
dot1xAuthEapolFramesRx
long
dot1xAuthEapolFramesRx
The number of valid EAPOL frames of any
type that have been received by this
Authenticator. REFERENCE 9.4.2, EAPOL
frames received.
dot1xAuthEapolFramesTx
long
dot1xAuthEapolFramesTx
The number of EAPOL frames of any type
that have been transmitted by this
Authenticator. REFERENCE 9.4.2, EAPOL
frames transmitted.
dot1xAuthEapolLogoffFramesRx
long
dot1xAuthEapolLogoffFra
mesRx
The number of EAPOL Logoff frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Logoff frames
received.
dot1xAuthEapolReqFramesTx
long
dot1xAuthEapolReqFrame
sTx
The number of EAP Request frames (other
than Rq/Id frames) that have been
transmitted by this Authenticator.
REFERENCE 9.4.2, EAPOL Request frames
transmitted.
dot1xAuthEapolReqIdFramesTx
long
dot1xAuthEapolReqIdFra
mesTx
The number of EAP Req/Id frames that
have been transmitted by this
Authenticator. REFERENCE 9.4.2, EAPOL
Req/Id frames transmitted.
dot1xAuthEapolRespFramesRx
long
dot1xAuthEapolRespFram
esRx
The number of valid EAP Response frames
(other than Resp/Id frames) that have
been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Response
frames received.
dot1xAuthEapolRespIdFramesRx
long
dot1xAuthEapolRespIdFra
mesRx
The number of EAP Resp/Id frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Resp/Id frames
received.
dot1xAuthEapolStartFramesRx
long
dot1xAuthEapolStartFram
esRx
The number of EAPOL Start frames that
have been received by this Authenticator.
REFERENCE 9.4.2, EAPOL Start frames
received.
dot1xAuthInvalidEapolFramesRx
long
dot1xAuthInvalidEapolFra
mesRx
The number of EAPOL frames that have
been received by this Authenticator in
which the frame type is not recognized.
REFERENCE 9.4.2, Invalid EAPOL frames
received.
dot1xAuthLastEapolFrameVersion
long
dot1xAuthLastEapolFram
eVersion
The protocol version number carried in
the most recently received EAPOL frame.
REFERENCE 9.4.2, Last EAPOL frame
version.
(4 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-99
E. 7450 ESS Release 7.0 statistics counters
Table E-22 ppp statistics
5620 SAM counter name
Type
MIB counter name
Description
PppStats
MIB table name: TIMETRA-PPP-MIB.tmnxPppTable
Monitored class: ppp.Interface
keepaliveEchoReplyPacketsReceiv
ed
long
tmnxPppKaInPktCount
The number of echo-reply packets
received.
keepaliveEchoRequestPacketsSent
long
tmnxPppKaOutPktCount
The number of echo-request packets
sent.
keepaliveThresholdExceedsCount
long
tmnxPppKaThresholdExce
edsCount
The number of times that
tmnxPppKaDropCount was reached.
lqmInRate
long
tmnxPppLqmInRate
The average of
'SaveInPackets'/'PeerOutPackets' in the
last five consecutive LQRs received.
lqmLqrPacketsReceived
long
tmnxPppLqmInPktCount
The number of LQR packets received.
lqmLqrPacketsSent
long
tmnxPppLqmOutPktCount
The number of LQR packets sent.
lqmOutRate
long
tmnxPppLqmOutRate
The average of
'PeerInPackets'/'LastOutPackets' in the
last five consecutive LQRs received.
lqmThresholdExceedsCount
long
tmnxPppLqmThresholdEx
ceedsCount
The number of times that either
tmnxPppLqmInRate or
tmnxPppLqmOutRate falls below the
specified quality percentage when PPP
quality or LQM is enforced.
Table E-23 radiusaccounting statistics
5620 SAM counter name
Type
MIB counter name
Description
PolicyStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubAcctPlcyStatsTable
Monitored class: radiusaccounting.Policy
receiveResponses
long
tmnxSubAcctPlcyRxRespo
nses
The value of
tmnxSubAcctPlcyRxResponses indicates
the number of accounting responses
received for this policy.
requestRetries
long
tmnxSubAcctPlcySendRet
ries
The value of tmnxSubAcctPlcySendRetries
indicates the number of retries to a
different server for a single accounting
request for this policy.
requestsFail
long
tmnxSubAcctPlcySendFail
The value of tmnxSubAcctPlcySendFail
indicates how many accounting requests
failed because the packet could not be
sent out.
requestTimeOut
long
tmnxSubAcctPlcyReqTim
eouts
The value of
tmnxSubAcctPlcyReqTimeouts indicates
the number of accounting requests which
have timed out for this policy.
(1 of 2)
E-100
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transferRequests
long
tmnxSubAcctPlcyTxReque
sts
The value of tmnxSubAcctPlcyTxRequests
indicates the number of accounting
requests transmitted for this policy.
RadiusEntryStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubAcctPlcyRadStatsTable
Monitored class: radiusaccounting.RadiusEntry
receiveResponses
long
tmnxSubAcctPlcyRadRxRe
sponses
The value of
tmnxSubAcctPlcyRadRxResponses
indicates the number of accounting
responses received for this server.
requestsFail
long
tmnxSubAcctPlcyRadReqS
endFail
The value of
tmnxSubAcctPlcyRadReqSendFail
indicates the number of accounting
requests failed because the packet could
not be sent out.
requestTimeOut
long
tmnxSubAcctPlcyRadReq
Timeouts
The value of
tmnxSubAcctPlcyRadReqTimeouts
indicates the number of accounting
requests which have timed out for this
server.
transferRequests
long
tmnxSubAcctPlcyRadTxRe
quests
The value of
tmnxSubAcctPlcyRadTxRequests indicates
the number of accounting requests
transmitted for this server.
(2 of 2)
Table E-24 ressubscr statistics
5620 SAM counter name
Type
MIB counter name
Description
BsxSubCustRecAppGrpStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxStatAaSubTable
Monitored class: ressubscr.ResidentialSubscriberInstance
appGrpName
String
tmnxBsxStatAaName
The value of tmnxBsxStatAaName
specifies either the ISA-AA protocol,
application or app-group name for which
statistics are requested. The
tmnxBsxStatAaType is used to determine
the statistics type.
BsxSubStudyAppStats
MIB table name: TIMETRA-BSX-NG-MIB.tmnxBsxStatAaSubSdyTable
Monitored class: ressubscr.ResidentialSubscriberInstance
appName
String
tmnxBsxStatAaName
The value of tmnxBsxStatAaName
specifies either the ISA-AA protocol,
application or app-group name for which
statistics are requested. The
tmnxBsxStatAaType is used to determine
the statistics type.
HostTrackStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubHostTrkStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
(1 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-101
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapInnerEncapValue
long
sapEncapValue
—
sapPortId
String
sapPortId
—
serviceId
long
svcId
—
statsType
int
tmnxSubHostTrkStatsTyp
e
The value of tmnxSubHostTrkStatsType
indicates the type of host tracking
statistics contained in
tmnxSubHostTrkStatsVal.
statsValue
long
tmnxSubHostTrkStatsVal
The value of tmnxSubHostTrkStatsType
indicates the value of the host tracking
statistics of the type indicated by
tmnxSubHostTrkStatsType, for this
subscriber host.
subscriberHostAddress
String
tmnxSubHostInfoV2IpAdd
ress
The value of tmnxSubHostInfoV2IpAddress
specifies the IP address of this subscriber
host.
subscriberHostAddressType
int
tmnxSubHostInfoV2IpAdd
ressType
The value of
tmnxSubHostInfoV2IpAddressType
specifies the type of address stored in
tmnxSubHostInfoV2IpAddress.
subscrIdent
String
tmnxSubInfoSubIdent
The value of tmnxSubInfoSubIdent
specifies the subscriber identification of
this subscriber.
HostTrackStatsOnSap
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubHostSapTrkStatsTable
Monitored classes:
vpls.L2AccessInterface
vprn.ServiceAccessPoint
ies.ServiceAccessPoint
•
•
•
statsType
int
tmnxSubHostSapTrkStats
Type
The value of
tmnxSubHostSapTrkStatsType indicates
the type of host tracking statistics
contained in tmnxSubHostSapTrkStatsVal.
statsValue
long
tmnxSubHostSapTrkStats
Val
The value of
tmnxSubHostSapTrkStatsType indicates
the value of the host tracking statistics of
the type indicated by
tmnxSubHostSapTrkStatsType, for this
host.
subscriberHostAddress
String
tmnxSubHostSapTrkHostA
ddr
The value of tmnxSubHostSapTrkHostAddr
indicates the address of the host.
subscriberHostAddressType
int
tmnxSubHostSapTrkHostA
ddrType
The value of
tmnxSubHostSapTrkHostAddrType
indicates the address type of
tmnxSubHostSapTrkHostAddr.
SLAProfInstEgrQStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSLAProfInstEgrQStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
egrQStatsDropInProfileOctets
UINT128
tmnxSPIEgrQStatsDropInP
rofOctets
The value of
tmnxSPIEgrQStatsDropInProfOctets
indicates the number of in-profile octets
discarded by the egress Qchip.
(2 of 13)
E-102
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
egrQStatsDropInProfilePackets
UINT128
tmnxSPIEgrQStatsDropInP
rofPkts
The value of
tmnxSPIEgrQStatsDropInProfPkts
indicates the number of in-profile packets
discarded by the egress Qchip.
egrQStatsDropOutProfileOctets
UINT128
tmnxSPIEgrQStatsDropOu
tProfOctets
The value of
tmnxSPIEgrQStatsDropOutProfOctets
indicates the number of out-of-profile
octets discarded by the egress Qchip.
egrQStatsDropOutProfilePackets
UINT128
tmnxSPIEgrQStatsDropOu
tProfPkts
The value of
tmnxSPIEgrQStatsDropOutProfPkts
indicates the number of out-of-profile
packets discarded by the egress Qchip.
egrQStatsFwdInProfileOctets
UINT128
tmnxSPIEgrQStatsFwdInPr
ofOctets
The value of
tmnxSPIEgrQStatsFwdInProfOctets
indicates the number of in-profile octets
(rate below CIR) forwarded by the egress
Qchip.
egrQStatsFwdInProfilePackets
UINT128
tmnxSPIEgrQStatsFwdInPr
ofPkts
The value of
tmnxSPIEgrQStatsFwdInProfPkts indicates
the number of in-profile packets (rate
below CIR) forwarded by the egress
Qchip.
egrQStatsFwdOutProfileOctets
UINT128
tmnxSPIEgrQStatsFwdOut
ProfOctets
The value of
tmnxSPIEgrQStatsFwdOutProfOctets
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
egress Qchip.
egrQStatsFwdOutProfilePackets
UINT128
tmnxSPIEgrQStatsFwdOut
ProfPkts
The value of
tmnxSPIEgrQStatsFwdOutProfPkts
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
egress Qchip.
egrQStatsQueueId
long
tmnxSPIEgrQStatsQueueI
d
The value of tmnxSPIEgrQStatsQueueId
specifies the index of the egress QoS
queue of this SLA profile instance.
slaProfileName
String
tmnxSLAProfName
The value of tmnxSLAProfName specifies
the name of the SLA profile.
SLAProfInstIngQStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSLAProfInstIngQStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
ingQStatsDropHiPriorityOctets
UINT128
tmnxSPIIngQStatsDropHiP
rioOctets
The value of
tmnxSPIIngQStatsDropHiPrioOctets
indicates the number of high priority
octets, as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQStatsDropHiPriorityPackets
UINT128
tmnxSPIIngQStatsDropHiP
rioPkts
The value of
tmnxSPIIngQStatsDropHiPrioPkts
indicates the number of high priority
packets, as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQStatsDropLoPriorityOctets
UINT128
tmnxSPIIngQStatsDropLoP
rioOctets
The value of
tmnxSPIIngQStatsDropLoPrioOctets
indicates the number of low priority
octets, as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
(3 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-103
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingQStatsDropLoPriorityPackets
UINT128
tmnxSPIIngQStatsDropLoP
rioPkts
The value of
tmnxSPIIngQStatsDropLoPrioPkts
indicates the number of low priority
packets, as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQStatsFwdInProfileOctets
UINT128
tmnxSPIIngQStatsFwdInPr
ofOctets
The value of
tmnxSPIIngQStatsFwdInProfOctets
indicates the number of in-profile octets
(rate below CIR) forwarded by the ingress
Qchip.
ingQStatsFwdInProfilePackets
UINT128
tmnxSPIIngQStatsFwdInPr
ofPkts
The value of
tmnxSPIIngQStatsFwdInProfPkts indicates
the number of in-profile packets (rate
below CIR) forwarded by the ingress
Qchip.
ingQStatsFwdOutProfileOctets
UINT128
tmnxSPIIngQStatsFwdOut
ProfOctets
The value of
tmnxSPIIngQStatsFwdOutProfOctets
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
ingress Qchip.
ingQStatsFwdOutProfilePackets
UINT128
tmnxSPIIngQStatsFwdOut
ProfPkts
The value of
tmnxSPIIngQStatsFwdOutProfPkts
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
ingress Qchip.
ingQStatsOffHiPriorityOctets
UINT128
tmnxSPIIngQStatsOffHiPri
oOctets
The value of
tmnxSPIIngQStatsOffHiPrioOctets
indicates the number of high priority
octets, as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
ingQStatsOffHiPriorityPackets
UINT128
tmnxSPIIngQStatsOffHiPri
oPkts
The value of
tmnxSPIIngQStatsOffHiPrioPkts indicates
the number of high priority packets, as
determined by the SLA profile ingress QoS
policy, offered by the Pchip to the Qchip.
ingQStatsOffLoPriorityOctets
UINT128
tmnxSPIIngQStatsOffLoPri
oOctets
The value of
tmnxSPIIngQStatsOffLoPrioOctets
indicates the number of low priority
octets, as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
ingQStatsOffLoPriorityPackets
UINT128
tmnxSPIIngQStatsOffLoPri
oPkts
The value of
tmnxSPIIngQStatsOffLoPrioPkts indicates
the number of low priority packets, as
determined by the SLA profile ingress QoS
policy, offered by the Pchip to the Qchip.
ingQStatsOffUncoloredOctets
UINT128
tmnxSPIIngQStatsOffUnco
lOctets
The value of
tmnxSPIIngQStatsOffUncolOctets
indicates the number of uncolored octets
offered to the ingress Qchip.
ingQStatsOffUncoloredPackets
UINT128
tmnxSPIIngQStatsOffUnco
lPkts
The value of
tmnxSPIIngQStatsOffUncolPkts indicates
the number of uncolored packets offered
to the ingress Qchip.
(4 of 13)
E-104
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingQStatsQueueId
long
tmnxSPIIngQStatsQueueId
The value of tmnxSPIIngQStatsQueueId
specifies the index of the ingress QoS
queue of this SLA profile instance.
slaProfileName
String
tmnxSLAProfName
The value of tmnxSLAProfName specifies
the name of the SLA profile.
SLAProfInstStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSLAProfInstStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
egrQchipDropInProfileOctets
UINT128
tmnxSPIStatsEgrQchipDro
pInProfOctets
The value of
tmnxSPIStatsEgrQchipDropInProfOctets
indicates the number of in-profile octets
dropped by the egress Qchip.
egrQchipDropInProfilePackets
UINT128
tmnxSPIStatsEgrQchipDro
pInProfPkts
The value of
tmnxSPIStatsEgrQchipDropInProfPkts
indicates the number of in-profile packets
dropped by the egress Qchip.
egrQchipDropOutProfileOctets
UINT128
tmnxSPIStatsEgrQchipDro
pOutProfOctets
The value of
tmnxSPIStatsEgrQchipDropOutProfOctets
indicates the number of out-of-profile
octets dropped by the egress Qchip.
egrQchipDropOutProfilePackets
UINT128
tmnxSPIStatsEgrQchipDro
pOutProfPkts
The value of
tmnxSPIStatsEgrQchipDropOutProfPkts
indicates the number of out-of-profile
packets dropped by the egress Qchip.
egrQchipFwdInProfileOctets
UINT128
tmnxSPIStatsEgrQchipFw
dInProfOctets
The value of
tmnxSPIStatsEgrQchipFwdInProfOctets
indicates the number of in-profile octets
(rate below CIR) forwarded by the egress
Qchip.
egrQchipFwdInProfilePackets
UINT128
tmnxSPIStatsEgrQchipFw
dInProfPkts
The value of
tmnxSPIStatsEgrQchipFwdInProfPkts
indicates the number of in-profile packets
(rate below CIR) forwarded by the egress
Qchip.
egrQchipFwdOutProfileOctets
UINT128
tmnxSPIStatsEgrQchipFw
dOutProfOctets
The value of
tmnxSPIStatsEgrQchipFwdOutProfOctets
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
egress Qchip.
egrQchipFwdOutProfilePackets
UINT128
tmnxSPIStatsEgrQchipFw
dOutProfPkts
The value of
tmnxSPIStatsEgrQchipFwdOutProfPkts
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
egress Qchip.
ingPchipOffHiPriorityOctets
UINT128
tmnxSPIStatsIngPchipOff
HiPrioOctets
The value of
tmnxSPIStatsIngPchipOffHiPrioOctets
indicates the number of high priority
octets as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
(5 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-105
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingPchipOffHiPriorityPackets
UINT128
tmnxSPIStatsIngPchipOff
HiPrioPkts
The value of
tmnxSPIStatsIngPchipOffHiPrioPkts
indicates the number of high priority
packets as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
ingPchipOffLoPriorityOctets
UINT128
tmnxSPIStatsIngPchipOffL
oPrioOctets
The value of
tmnxSPIStatsIngPchipOffLoPrioOctets
indicates the number of low priority
octets as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
ingPchipOffLoPriorityPackets
UINT128
tmnxSPIStatsIngPchipOffL
oPrioPkts
The value of
tmnxSPIStatsIngPchipOffLoPrioPkts
indicates the number of low priority
packets as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
ingPchipOffUncoloredOctets
UINT128
tmnxSPIStatsIngPchipOff
UncolOctets
The value of
tmnxSPIStatsIngPchipOffUncolOctets
indicates the number of uncolored octets
as determined by the SLA profile ingress
QoS policy, offered by the Pchip to the
Qchip.
ingPchipOffUncoloredPackets
UINT128
tmnxSPIStatsIngPchipOff
UncolPkts
The value of
tmnxSPIStatsIngPchipOffUncolPkts
indicates the number of uncolored
packets as determined by the SLA profile
ingress QoS policy, offered by the Pchip to
the Qchip.
ingQchipDropHiPriorityOctets
UINT128
tmnxSPIStatsIngQchipDro
pHiPrioOctets
The value of
tmnxSPIStatsIngQchipDropHiPrioOctets
indicates the number of high priority
octets as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQchipDropHiPriorityPackets
UINT128
tmnxSPIStatsIngQchipDro
pHiPrioPkts
The value of
tmnxSPIStatsIngQchipDropHiPrioPkts
indicates the number of high priority
packets as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQchipDropLoPriorityOctets
UINT128
tmnxSPIStatsIngQchipDro
pLoPrioOctets
The value of
tmnxSPIStatsIngQchipDropLoPrioOctets
indicates the number of low priority
octets as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQchipDropLoPriorityPackets
UINT128
tmnxSPIStatsIngQchipDro
pLoPrioPkts
The value of
tmnxSPIStatsIngQchipDropLoPrioPkts
indicates the number of low priority
packets as determined by the SLA profile
ingress QoS policy, dropped by the Qchip.
ingQchipFwdInProfileOctets
UINT128
tmnxSPIStatsIngQchipFwd
InProfOctets
The value of
tmnxSPIStatsIngQchipFwdInProfOctets
indicates the number of in-profile octets
(rate below CIR) forwarded by the ingress
Qchip.
(6 of 13)
E-106
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingQchipFwdInProfilePackets
UINT128
tmnxSPIStatsIngQchipFwd
InProfPkts
The value of
tmnxSPIStatsIngQchipFwdInProfPkts
indicates the number of in-profile packets
(rate below CIR) forwarded by the ingress
Qchip.
ingQchipFwdOutProfileOctets
UINT128
tmnxSPIStatsIngQchipFwd
OutProfOctets
The value of
tmnxSPIStatsIngQchipFwdOutProfOctets
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
ingress Qchip.
ingQchipFwdOutProfilePackets
UINT128
tmnxSPIStatsIngQchipFwd
OutProfPkts
The value of
tmnxSPIStatsIngQchipFwdOutProfPkts
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
ingress Qchip.
slaProfileName
String
tmnxSLAProfName
The value of tmnxSLAProfName specifies
the name of the SLA profile.
SubEgrQosSchedStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubEgrQosSchedStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
egrQosSchedName
String
tmnxSubEgrQosSchedStat
sName
The value of
tmnxSubEgrQosSchedStatsName specifies
the egress QoS scheduler of this
subscriber.
forwardedOctets
UINT128
tmnxSubEgrQosSchedStat
sFwdOctets
The value of
tmnxSubEgrQosSchedStatsFwdOctets
indicates the number of forwarded octets
by the egress Qchip, as determined by the
subscriber egress scheduler policy.
forwardedPackets
UINT128
tmnxSubEgrQosSchedStat
sFwdPkts
The value of
tmnxSubEgrQosSchedStatsFwdPkts
indicates the number of forwarded
packets by the egress Qchip, as
determined by the subscriber egress
scheduler policy.
SubIngQosSchedStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubIngQosSchedStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
forwardedOctets
UINT128
tmnxSubIngQosSchedStat
sFwdOctets
The value of
tmnxSubIngQosSchedStatsFwdOctets
indicates the number of forwarded
octets, as determined by the subscriber
ingress scheduler policy, offered by the
Pchip to the Qchip.
forwardedPackets
UINT128
tmnxSubIngQosSchedStat
sFwdPkts
The value of
tmnxSubIngQosSchedStatsFwdPkts
indicates the number of forwarded
packets, as determined by the subscriber
ingress scheduler policy, offered by the
Pchip to the Qchip.
ingQosSchedName
String
tmnxSubIngQosSchedStat
sName
The value of
tmnxSubIngQosSchedStatsName specifies
the ingress QoS scheduler of this
subscriber.
(7 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-107
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
SubscriberEgrOverrideCounterStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubEgrOverrideCounterTable
Monitored class: ressubscr.ResidentialSubscriberInstance
subEgrOvrCounterDropInProfileOct
ets
UINT128
tmnxSubEgrOvrCntrDropI
nProfOcts
The value of
tmnxSubEgrOvrCntrDropInProfOcts
indicates the number of high-priority
octets dropped for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterDropInProfilePac
kets
UINT128
tmnxSubEgrOvrCntrDropI
nProfPkts
The value of
tmnxSubEgrOvrCntrDropInProfPkts
indicates the number of high-priority
packets dropped for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterDropOutProfileP
ackets
UINT128
tmnxSubEgrOvrCntrDropO
utProfPkts
The value of
tmnxSubEgrOvrCntrDropOutProfPkts
indicates the number of low-priority
packets dropped for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterFwdInProfileOct
ets
UINT128
tmnxSubEgrOvrCntrFwdIn
ProfOcts
The value of
tmnxSubEgrOvrCntrFwdInProfOcts
indicates the number of in-profile octets
forwarded for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterFwdInProfilePac
kets
UINT128
tmnxSubEgrOvrCntrFwdIn
ProfPkts
The value of
tmnxSubEgrOvrCntrFwdInProfPkts
indicates the number of in-profile packets
forwarded for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterFwdOutProfileO
ctets
UINT128
tmnxSubEgrOvrCntrFwdO
utProfOcts
The value of
tmnxSubEgrOvrCntrFwdOutProfOcts
indicates the number of out-of-profile
octets forwarded for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterFwdOutProfilePa
ckets
UINT128
tmnxSubEgrOvrCntrFwdO
utProfPkts
The value of
tmnxSubEgrOvrCntrFwdOutProfPkts
indicates the number of out-of-profile
packets forwarded for the egress counter,
specified by the index
tmnxSubEgrOvrCntrId, on this subscriber.
subEgrOvrCounterId
long
tmnxSubEgrOvrCntrId
The value of tmnxSubEgrOvrCntrId
indicates the counter ID for the statistics.
subEgrOvrCounterSubPortId
long
tmnxSubEgrOvrCntrSubPo
rtId
The value of
tmnxSubEgrOvrCntrSubPortId indicates
the access port for this entry.
SubscriberEgrQStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubscriberEgrQStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
(8 of 13)
E-108
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
subEgrQStatsDropInProfileOctets
UINT128
tmnxSubEgrQStatsDropIn
ProfOcts
The value of
tmnxSubEgrQStatsDropInProfOcts
indicates the number of high-priority
octets dropped on egress on this
subscriber.
subEgrQStatsDropInProfilePackets
UINT128
tmnxSubEgrQStatsDropIn
ProfPkts
The value of
tmnxSubEgrQStatsDropInProfPkts
indicates the number of high-priority
packets dropped on egress on this
subscriber.
subEgrQStatsDropOutProfileOctets
UINT128
tmnxSubEgrQStatsDropOu
tProfOcts
The value of
tmnxSubEgrQStatsDropOutProfOcts
indicates the number of low-priority
octets dropped on egress on this
subscriber.
subEgrQStatsDropOutProfilePacket
s
UINT128
tmnxSubEgrQStatsDropOu
tProfPkts
The value of
tmnxSubEgrQStatsDropOutProfPkts
indicates the number of low-priority
packets dropped on egress on this
subscriber.
subEgrQStatsFwdInProfileOctets
UINT128
tmnxSubEgrQStatsFwdInP
rofOcts
The value of
tmnxSubEgrQStatsFwdInProfOcts
indicates the number of out-of-profile
octets forwarded on egress on this
subscriber.
subEgrQStatsFwdInProfilePackets
UINT128
tmnxSubEgrQStatsFwdInP
rofPkts
The value of
tmnxSubEgrQStatsFwdInProfPkts
indicates the number of in-profile packets
forwarded on egress on this subscriber.
subEgrQStatsFwdOutProfileOctets
UINT128
tmnxSubEgrQStatsFwdOu
tProfOcts
The value of
tmnxSubEgrQStatsFwdOutProfOcts
indicates the number of out-of-profile
octets forwarded on egress on this
subscriber.
subEgrQStatsFwdOutProfilePacket
s
UINT128
tmnxSubEgrQStatsFwdOu
tProfPkts
The value of
tmnxSubEgrQStatsFwdOutProfPkts
indicates the number of out-of-profile
packets forwarded on egress on this
subscriber.
subEgrQStatsHsmdaQueueId
long
tmnxSubEgrQStatsQueueI
d
The value of tmnxSubEgrQStatsQueueId
index specifies the Hsmda egress queue
for this entry.
subEgrQStatsSubPortId
long
tmnxSubEgrQStatsSubPor
tId
The value of tmnxSubEgrQStatsSubPortId
indicates the access port for this entry.
SubscriberHsmdaStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubscriberHsmdaStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
hsmdaStatsSubPortId
long
tmnxSubHsmdaStSubPortI
d
The value of tmnxSubHsmdaStSubPortId
indicates the access port for this entry.
subEgrDropInProfileOctets
UINT128
tmnxSubHsmdaStEgrDropI
nProfOct
The value of
tmnxSubHsmdaStEgrDropInProfOct
indicates the number of high-priority
octets discarded by the egress Qchip for
this subscriber.
(9 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-109
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
subEgrDropInProfilePackets
UINT128
tmnxSubHsmdaStEgrDropI
nProfPkt
The value of
tmnxSubHsmdaStEgrDropInProfPkt
indicates the number of high-priority
packets discarded by the egress Qchip for
this subscriber.
subEgrDropOutProfileOctets
UINT128
tmnxSubHsmdaStEgrDrop
OutProfOct
The value of
tmnxSubHsmdaStEgrDropOutProfOct
indicates the number of low-priority
octets discarded by the egress Qchip for
this subscriber.
subEgrDropOutProfilePackets
UINT128
tmnxSubHsmdaStEgrDrop
OutProfPkt
The value of
tmnxSubHsmdaStEgrDropOutProfPkt
indicates the number of low-priority
packets discarded by the egress Qchip for
this subscriber.
subEgrFwdInProfilePackets
UINT128
tmnxSubHsmdaStEgrFwdI
nProfPkt
The value of
tmnxSubHsmdaStEgrFwdInProfPkt
indicates the number of in-profile packets
forwarded by the egress Qchip for this
subscriber.
subEgrFwdOutProfileOctets
UINT128
tmnxSubHsmdaStEgrFwd
OutProfOct
The value of
tmnxSubHsmdaStEgrFwdOutProfOct
indicates the number of out-of-profile
octets forwarded by the egress Qchip for
this subscriber.
subEgrFwdOutProfilePackets
UINT128
tmnxSubHsmdaStEgrFwd
OutProfPkt
The value of
tmnxSubHsmdaStEgrFwdOutProfPkt
indicates the number of out-of-profile
packets forwarded by the egress Qchip for
this subscriber.
subIngDropHiPriorityOctets
UINT128
tmnxSubHsmdaStIngDrop
HiPrioOct
The value of
tmnxSubHsmdaStIngDropHiPrioOct
indicates the number of high-priority
octets discarded by the ingress Qchip for
this subscriber.
subIngDropHiPriorityPackets
UINT128
tmnxSubHsmdaStIngDrop
HiPrioPkt
The value of
tmnxSubHsmdaStIngDropHiPrioPkt
indicates the number of high-priority
packets discarded by the ingress Qchip for
this subscriber.
subIngDropLoPriorityOctets
UINT128
tmnxSubHsmdaStIngDrop
LoPrioOct
The value of
tmnxSubHsmdaStIngDropLoPrioOct
indicates the number of low-priority
octets discarded by the ingress Qchip for
this subscriber.
subIngDropLoPriorityPackets
UINT128
tmnxSubHsmdaStIngDrop
LoPrioPkt
The value of
tmnxSubHsmdaStIngDropLoPrioPkt
indicates the number of low-priority
packets discarded by the ingress Qchip for
this subscriber.
subIngFwdInProfileOctets
UINT128
tmnxSubHsmdaStIngFwdI
nProfOct
The value of
tmnxSubHsmdaStIngFwdInProfOct
indicates the number of out-of-profile
octets forwarded by the ingress Qchip for
this subscriber.
(10 of 13)
E-110
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
subIngFwdInProfilePackets
UINT128
tmnxSubHsmdaStIngFwdI
nProfPkt
The value of
tmnxSubHsmdaStIngFwdInProfPkt
indicates the number of in-profile packets
forwarded by the ingress Qchip for this
subscriber.
subIngFwdOutProfileOctets
UINT128
tmnxSubHsmdaStIngFwdO
utProfOct
The value of
tmnxSubHsmdaStIngFwdOutProfOct
indicates the number of out-of-profile
octets forwarded by the ingress Qchip for
this subscriber.
subIngFwdOutProfilePackets
UINT128
tmnxSubHsmdaStIngFwdO
utProfPkt
The value of
tmnxSubHsmdaStIngFwdOutProfPkt
indicates the number of out-of-profile
packets forwarded by the ingress Qchip
for this subscriber.
subIngOffTotalOctets
UINT128
tmnxSubHsmdaStIngOffT
otalOct
The value of
tmnxSubHsmdaStIngOffTotalOct indicates
the total number of octets offered on
ingress for this subscriber.
subIngOffTotalPackets
UINT128
tmnxSubHsmdaStIngOffT
otalPkt
The value of
tmnxSubHsmdaStIngOffTotalPkt indicates
the total number of packets offered on
ingress for this subscriber.
SubscriberIngOverrideCounterStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubIngOverrideCounterTable
Monitored class: ressubscr.ResidentialSubscriberInstance
subIngOvrCounterDropHiPriorityOc
tets
UINT128
tmnxSubIngOvrCntrDropH
iPrioOcts
The value of
tmnxSubIngOvrCntrDropHiPrioOcts
indicates the number of high-priority
octets dropped for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterDropHiPriorityPa
ckets
UINT128
tmnxSubIngOvrCntrDropH
iPrioPkts
The value of
tmnxSubIngOvrCntrDropHiPrioPkts
indicates the number of high-priority
packets dropped for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterDropLoPriorityOc
tets
UINT128
tmnxSubIngOvrCntrDropL
oPrioOcts
The value of
tmnxSubIngOvrCntrDropLoPrioOcts
indicates the number of low-priority
octets dropped for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterDropLoPriorityPa
ckets
UINT128
tmnxSubIngOvrCntrDropL
oPrioPkts
The value of
tmnxSubIngOvrCntrDropLoPrioPkts
indicates the number of low-priority
packets dropped for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterFwdInProfileOct
ets
UINT128
tmnxSubIngOvrCntrFwdIn
ProfOcts
The value of
tmnxSubIngOvrCntrFwdInProfOcts
indicates the number of in-profile octets
forwarded for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
(11 of 13)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-111
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
subIngOvrCounterFwdInProfilePac
kets
UINT128
tmnxSubIngOvrCntrFwdIn
ProfPkts
The value of
tmnxSubIngOvrCntrFwdInProfPkts
indicates the number of in-profile packets
forwarded for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterFwdOutProfileOc
tets
UINT128
tmnxSubIngOvrCntrFwdO
utProfOcts
The value of
tmnxSubIngOvrCntrFwdOutProfOcts
indicates the number of out-of-profile
octets forwarded for the ingress counter,
specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterFwdOutProfilePa
ckets
UINT128
tmnxSubIngOvrCntrFwdO
utProfPkts
The value of
tmnxSubIngOvrCntrFwdOutProfPkts
indicates the number of out-of-profile
packets forwarded for the ingress
counter, specified by the index
tmnxSubIngOvrCntrId, on this subscriber.
subIngOvrCounterId
long
tmnxSubIngOvrCntrId
The value of tmnxSubIngOvrCntrId
indicates the counter ID for the statistics.
subIngOvrCounterOffTotalOctets
UINT128
tmnxSubIngOvrCntrOffTo
talOcts
The value of
tmnxSubIngOvrCntrOffTotalOcts indicates
the total number of octets offered on
ingress on this subscriber.
subIngOvrCounterOffTotalPackets
UINT128
tmnxSubIngOvrCntrOffTo
talPkts
The value of
tmnxSubIngOvrCntrOffTotalPkts indicates
the total number of packets offered on
ingress on this subscriber.
subIngOvrCounterSubPortId
long
tmnxSubIngOvrCntrSubPo
rtId
The value of tmnxSubIngOvrCntrSubPortId
indicates the access port for this entry.
SubscriberIngQStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubscriberIngQStatsTable
Monitored class: ressubscr.ResidentialSubscriberInstance
subIngQStatsDropHiPriorityOctets
UINT128
tmnxSubIngQStatsDropHi
PrioOcts
The value of
tmnxSubIngQStatsDropHiPrioOcts
indicates the number of high-priority
octets dropped on ingress on this
subscriber.
subIngQStatsDropHiPriorityPackets
UINT128
tmnxSubIngQStatsDropHi
PrioPkts
The value of
tmnxSubIngQStatsDropHiPrioPkts
indicates the number of high-priority
packets dropped on ingress on this
subscriber.
subIngQStatsDropLoPriorityOctets
UINT128
tmnxSubIngQStatsDropLo
PrioOcts
The value of
tmnxSubIngQStatsDropLoPrioOcts
indicates the number of low-priority
octets dropped on ingress on this
subscriber.
subIngQStatsDropLoPriorityPacket
s
UINT128
tmnxSubIngQStatsDropLo
PrioPkts
The value of
tmnxSubIngQStatsDropLoPrioPkts
indicates the number of low-priority
packets dropped on ingress on this
subscriber.
(12 of 13)
E-112
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
subIngQStatsFwdInProfileOctets
UINT128
tmnxSubIngQStatsFwdInP
rofOcts
The value of
tmnxSubIngQStatsFwdInProfOcts
indicates the number of out-of-profile
octets forwarded on ingress on this
subscriber.
subIngQStatsFwdInProfilePackets
UINT128
tmnxSubIngQStatsFwdInP
rofPkts
The value of
tmnxSubIngQStatsFwdInProfPkts
indicates the number of in-profile packets
forwarded on ingress on this subscriber.
subIngQStatsFwdOutProfileOctets
UINT128
tmnxSubIngQStatsFwdOut
ProfOcts
The value of
tmnxSubIngQStatsFwdOutProfOcts
indicates the number of out-of-profile
octets forwarded on ingress on this
subscriber.
subIngQStatsFwdOutProfilePackets
UINT128
tmnxSubIngQStatsFwdOut
ProfPkts
The value of
tmnxSubIngQStatsFwdOutProfPkts
indicates the number of out-of-profile
packets forwarded on ingress on this
subscriber.
subIngQStatsHsmdaQueueId
long
tmnxSubIngQStatsQueueI
d
The value of tmnxSubIngQStatsQueueId
index specifies the Hsmda ingress queue
for this entry.
subIngQStatsOffTotalOctets
UINT128
tmnxSubIngQStatsOffTota
lOcts
The value of
tmnxSubIngQStatsOffTotalOcts indicates
the total number of octets offered on
ingress on this subscriber.
subIngQStatsOffTotalPackets
UINT128
tmnxSubIngQStatsOffTota
lPkts
The value of
tmnxSubIngQStatsOffTotalPkts indicates
the total number of packets offered for
this subscriber.
subIngQStatsSubPortId
long
tmnxSubIngQStatsSubPort
Id
The value of tmnxSubIngQStatsSubPortId
indicates the access port for this entry.
(13 of 13)
Table E-25 rip statistics
5620 SAM counter name
Type
MIB counter name
Description
InterfaceReceiveStats
MIB table name: TIMETRA-RIP-MIB.vRtrRipIfStatTable
Monitored class: rip.Interface
badPackets
long
vRtrRipIfStatAllRcvBadPa
ckets
vRtrRipIfStatAllRcvBadPackets is the
number of RIP updates received on this
interface that were discarded as invalid.
v1BadRoutes
long
vRtrRipIfStatV1BadRoutes
vRtrRipIfStatV1BadRoutes is the number
of routes, in valid RIPv1 packets, which
were ignored for any reason (e.g.
unknown address family, or invalid
metric).
v1Requests
long
vRtrRipIfStatV1RcvReque
sts
vRtrRipIfStatV1RcvRequests is the number
of RIPv1 request packets received by the
RIP process.
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-113
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
v1RequestsIgnored
long
vRtrRipIfStatV1BadReque
sts
vRtrRipIfStatV1BadRequests is the
number of RIPv1 request packets received
by the RIP process that were subsequently
discarded for any reason.
v1Updates
long
vRtrRipIfStatV1RcvUpdat
es
vRtrRipIfStatV1RcvUpdates is the number
of RIPv1 response packets received by the
RIP process.
v1UpdatesIgnored
long
vRtrRipIfStatV1BadUpdat
es
vRtrRipIfStatV1BadUpdates is the number
of RIPv1 response packets received by the
RIP process which were subsequently
discarded for any reason.
v2AuthenticationErrors
long
vRtrRipIfStatAuthErrors
vRtrRipIfStatAuthErrors is the number of
RIPv2 packets received by the RIP process
which were subsequently discarded
because of an error authenticating the
packet.
v2BadRoutes
long
vRtrRipIfStatV2BadRoutes
vRtrRipIfStatV2BadRoutes is the number
of routes, in valid RIPv2 packets, which
were ignored for any reason (e.g.
unknown address family, or invalid
metric).
v2Requests
long
vRtrRipIfStatV2RcvReque
sts
vRtrRipIfStatV2RcvRequests is the number
of RIPv2 request packets received by the
RIP process.
v2RequestsIgnored
long
vRtrRipIfStatV2BadReque
sts
vRtrRipIfStatV2BadRequests is the
number of RIPv2 request packets received
by the RIP process that were subsequently
discarded for any reason.
v2Updates
long
vRtrRipIfStatV2RcvUpdat
es
vRtrRipIfStatV2RcvUpdates is the number
of RIPv2 response packets received by the
RIP process.
v2UpdatesIgnored
long
vRtrRipIfStatV2BadUpdat
es
vRtrRipIfStatV2BadUpdates is the number
of RIPv2 response packets received by the
RIP process which were subsequently
discarded for any reason.
InterfaceTransmitStats
MIB table name: TIMETRA-RIP-MIB.vRtrRipIfStatTable
Monitored class: rip.Interface
totalUpdates
long
vRtrRipIfStatAllSentUpda
tes
vRtrRipIfStatAllSentUpdates is the
number of all RIP updates actually sent on
this interface. This explicitly does include
full updates sent containing new
information.
triggeredUpdates
long
vRtrRipIfStatAllTriggered
Updates
vRtrRipIfStatAllTriggeredUpdates is the
number of triggered RIP updates actually
sent on this interface. This explicitly does
include full updates sent containing new
information.
(2 of 2)
E-114
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
Table E-26 rsvp statistics
5620 SAM counter name
Type
MIB counter name
Description
AuthenticationKeyStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfStatTable
Monitored class: rsvp.AuthenticationKey
errorPacketsReceived
UINT128
vRtrRsvpIfStatRxAuthErro
rs
The total number of RSVP packets with
MD5 errors received on this RSVP
interface.
errorPacketsTransmitted
UINT128
vRtrRsvpIfStatTxAuthErro
rs
The total number of RSVP packets with
MD5 errors sent by this RSVP interface.
RsvpInterfaceReceiveStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfStatTable
Monitored class: rsvp.Interface
acks
UINT128
vRtrRsvpIfStatRxAcks
The total number of RSVP ACK messages
received when refresh reduction is
enabled on this RSVP interface.
acks
UINT128
vRtrRsvpIfStatTxAcks
The total number of RSVP ACK messages
that have been transmitted on this RSVP
interface when refresh reduction is
enabled.
bundles
UINT128
vRtrRsvpIfStatRxBundles
The total number of RSVP bundled
packets received on this RSVP interface.
Bundled packets are sent when refresh
reduction is enabled.
bundles
UINT128
vRtrRsvpIfStatTxBundles
The total number of RSVP bundled
packets that have been transmitted on
this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatRxErrorPkts
The total number of RSVP packets with
errors received on this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatTxErrorPkts
The total number of RSVP packets with
errors that have been transmitted on this
RSVP interface.
hellos
UINT128
vRtrRsvpIfStatRxHelloReq
s
The total number of RSVP HELLO REQ
messages received on this RSVP interface.
hellos
UINT128
vRtrRsvpIfStatTxHelloReq
s
The total number of RSVP HELLO REQ
packets that have been transmitted on
this RSVP interface.
helloTimeout
long
vRtrRsvpIfStatHelloTimeo
ut
The total number of hello messages that
timed out on this RSVP interface.
packets
UINT128
vRtrRsvpIfStatRxPkts
The total number of error free RSVP
packets received on this RSVP interface.
packets
UINT128
vRtrRsvpIfStatTxPkts
The total number of error free RSVP
packets that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatRxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatTxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted
from this RSVP interface.
(1 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-115
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
paths
UINT128
vRtrRsvpIfStatRxPaths
The total number of RSVP PATH messages
that have been received on this RSVP
interface.
paths
UINT128
vRtrRsvpIfStatTxPaths
The total number of RSVP PATH messages
that have been transmitted from this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatRxPathTear
s
The total number of RSVP PATH TEAR
messages that have been received on this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatTxPathTear
s
The total number of RSVP PATH TEAR
messages that have been transmitted
from this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatRxSRefresh
es
The total number of RSVP summary
refresh, SREFRESH, messages received on
this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatTxSRefresh
es
The total number of summary refresh,
SREFRESH, messages that have been
transmitted on this RSVP interface when
refresh reduction is enabled.
reserveConfirms
UINT128
vRtrRsvpIfStatRxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been received on this
RSVP interface.
reserveConfirms
UINT128
vRtrRsvpIfStatTxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been transmitted
from this RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatRxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been received on this
RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatTxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been transmitted
from this RSVP interface.
reserves
UINT128
vRtrRsvpIfStatRxResvs
The total number of RSVP RESV messages
that have been received on this RSVP
interface.
reserves
UINT128
vRtrRsvpIfStatTxResvs
The total number of RSVP RESV messages
that have been transmitted from this
RSVP interface.
reserveTears
UINT128
vRtrRsvpIfStatRxResvTear
s
The total number of RSVP RESV TEAR
messages that have been received on this
RSVP interface.
reserveTears
UINT128
vRtrRsvpIfStatTxResvTear
s
The total number of RSVP RESV TEAR
messages that have been transmitted
from this RSVP interface.
totalPackets
UINT128
vRtrRsvpIfStatRxTotalPkt
s
The total number of RSVP packets,
including errors, received on this RSVP
interface.
totalPackets
UINT128
vRtrRsvpIfStatTxTotalPkt
s
The total number of RSVP packets,
including error packets, that have been
transmitted on this RSVP interface.
RsvpInterfaceStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfTable
Monitored class: rsvp.Interface
(2 of 5)
E-116
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
activeReservations
long
vRtrRsvpIfActiveReservati
onCount
The total number of active RSVP sessions
that have reserved bandwidth.
activeSessions
long
vRtrRsvpIfActiveSessionC
ount
The total number of active RSVP sessions
on this interface. This count includes
sessions that have requested bandwidth
as well as sessions that have not
requested any bandwidth.
bandwidth
long
vRtrRsvpIfBandwidth
The value of vRtrRsvpIfBandwidth
specifies the amount of bandwidth in
mega-bits per second (Mbps) available to
be reserved for the RSVP protocol on this
interface. This is typically the (port Speed
* subscription Percentage).
reservedBandwidth
long
vRtrRsvpIfReservedBandw
idth
The value of
vRtrRsvpIfReservedBandwidth specifies
the amount of bandwidth in mega-bits per
second (Mbps) to reserved by the RSVP
sessions on this interface. A value of zero
(0) indicates that no bandwidth is
reserved.
totalSessions
long
vRtrRsvpIfTotalSessionCo
unt
The total number of RSVP sessions on this
interface. This count includes sessions
that are active as well as sessions that
have been signalled but a response has
not yet been received.
RsvpInterfaceTransmitStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpIfStatTable
Monitored class: rsvp.Interface
acks
UINT128
vRtrRsvpIfStatRxAcks
The total number of RSVP ACK messages
received when refresh reduction is
enabled on this RSVP interface.
acks
UINT128
vRtrRsvpIfStatTxAcks
The total number of RSVP ACK messages
that have been transmitted on this RSVP
interface when refresh reduction is
enabled.
bundles
UINT128
vRtrRsvpIfStatRxBundles
The total number of RSVP bundled
packets received on this RSVP interface.
Bundled packets are sent when refresh
reduction is enabled.
bundles
UINT128
vRtrRsvpIfStatTxBundles
The total number of RSVP bundled
packets that have been transmitted on
this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatRxErrorPkts
The total number of RSVP packets with
errors received on this RSVP interface.
errorPackets
UINT128
vRtrRsvpIfStatTxErrorPkts
The total number of RSVP packets with
errors that have been transmitted on this
RSVP interface.
hellos
UINT128
vRtrRsvpIfStatRxHelloReq
s
The total number of RSVP HELLO REQ
messages received on this RSVP interface.
hellos
UINT128
vRtrRsvpIfStatTxHelloReq
s
The total number of RSVP HELLO REQ
packets that have been transmitted on
this RSVP interface.
(3 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-117
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
packets
UINT128
vRtrRsvpIfStatRxPkts
The total number of error free RSVP
packets received on this RSVP interface.
packets
UINT128
vRtrRsvpIfStatTxPkts
The total number of error free RSVP
packets that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatRxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted on
this RSVP interface.
pathErrors
UINT128
vRtrRsvpIfStatTxPathErro
rs
The total number of RSVP PATH ERROR
messages that have been transmitted
from this RSVP interface.
paths
UINT128
vRtrRsvpIfStatRxPaths
The total number of RSVP PATH messages
that have been received on this RSVP
interface.
paths
UINT128
vRtrRsvpIfStatTxPaths
The total number of RSVP PATH messages
that have been transmitted from this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatRxPathTear
s
The total number of RSVP PATH TEAR
messages that have been received on this
RSVP interface.
pathTears
UINT128
vRtrRsvpIfStatTxPathTear
s
The total number of RSVP PATH TEAR
messages that have been transmitted
from this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatRxSRefresh
es
The total number of RSVP summary
refresh, SREFRESH, messages received on
this RSVP interface.
refreshes
UINT128
vRtrRsvpIfStatTxSRefresh
es
The total number of summary refresh,
SREFRESH, messages that have been
transmitted on this RSVP interface when
refresh reduction is enabled.
reserveConfirms
UINT128
vRtrRsvpIfStatRxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been received on this
RSVP interface.
reserveConfirms
UINT128
vRtrRsvpIfStatTxResvConf
irms
The total number of RSVP RESV CONFIRM
messages that have been transmitted
from this RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatRxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been received on this
RSVP interface.
reserveErrors
UINT128
vRtrRsvpIfStatTxResvErro
rs
The total number of RSVP RESV ERROR
messages that have been transmitted
from this RSVP interface.
reserves
UINT128
vRtrRsvpIfStatRxResvs
The total number of RSVP RESV messages
that have been received on this RSVP
interface.
reserves
UINT128
vRtrRsvpIfStatTxResvs
The total number of RSVP RESV messages
that have been transmitted from this
RSVP interface.
reserveTears
UINT128
vRtrRsvpIfStatRxResvTear
s
The total number of RSVP RESV TEAR
messages that have been received on this
RSVP interface.
(4 of 5)
E-118
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
reserveTears
UINT128
vRtrRsvpIfStatTxResvTear
s
The total number of RSVP RESV TEAR
messages that have been transmitted
from this RSVP interface.
totalPackets
UINT128
vRtrRsvpIfStatRxTotalPkt
s
The total number of RSVP packets,
including errors, received on this RSVP
interface.
totalPackets
UINT128
vRtrRsvpIfStatTxTotalPkt
s
The total number of RSVP packets,
including error packets, that have been
transmitted on this RSVP interface.
RsvpSessionStats
MIB table name: TIMETRA-RSVP-MIB.vRtrRsvpSessionStatTable
Monitored class: rsvp.Session
detourAge
long
vRtrRsvpSessionDetourAg
e
vRtrRsvpSessionDetourAge is the age
(i.e., time from creation till now) of this
detour LSP in 10-millisecond periods.
detourTimeUp
long
vRtrRsvpSessionDetourTi
meUp
vRtrRsvpSessionDetourTimeUp is the total
time in 10-millisecond units that the
detour LSP has been operational.
pathsReceived
UINT128
vRtrRsvpSessionRxPaths
The total number of RSVP PATH messages
received for this RSVP session.
pathsTransmitted
UINT128
vRtrRsvpSessionTxPaths
The total number of RSVP PATH messages
transmitted for this RSVP session.
refreshPathsReceived
UINT128
vRtrRsvpSessionRxSrefres
hPaths
The value of
vRtrRsvpSessionRxSrefreshPaths indicates
the number of times PATH was refreshed
using message ID from full PATH refresh or
Srefresh message for this RSVP session.
refreshPathsTransmitted
UINT128
vRtrRsvpSessionTxSrefres
hPaths
The value of
vRtrRsvpSessionTxSrefreshPaths indicates
the number of times PATH refresh for the
session was sent as a part of a Srefresh
message.
refreshReservesReceived
UINT128
vRtrRsvpSessionRxSrefres
hResvs
The value of
vRtrRsvpSessionRxSrefreshResvs indicates
the number of times RESV was refreshed
using message ID from full RESV refresh or
Srefresh message for this RSVP session.
refreshReservesTransmitted
UINT128
vRtrRsvpSessionTxSrefres
hResvs
The value of
vRtrRsvpSessionTxSrefreshResvs indicates
the number of times RESV refresh for the
session was sent as a part of a Srefresh
message.
reservesReceived
UINT128
vRtrRsvpSessionRxResvs
The total number of RSVP RESV messages
received for this RSVP session.
reservesTransmitted
UINT128
vRtrRsvpSessionTxResvs
The total number of RSVP RESV messages
transmitted for this RSVP session.
(5 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-119
E. 7450 ESS Release 7.0 statistics counters
Table E-27 rtr statistics
5620 SAM counter name
Type
MIB counter name
Description
CpeCheckStats
MIB table name: TIMETRA-VRTR-MIB.vRtrInetStatRteCpeChkStatsTable
Monitored class: rtr.StaticRoute
downTransitions
long
vRtrInetStatRteCpeChkDo
wnTrans
The value of
vRtrInetStatRteCpeChkDownTrans
indicates the number of times the CPE has
transitioned to the unavailable state.
echoReplyPacketsReceived
long
vRtrInetStatRteCpeChkIn
PktCnt
The value of
vRtrInetStatRteCpeChkInPktCnt indicates
the number of echo-reply packets
received.
echoRequestPacketsSent
long
vRtrInetStatRteCpeChkOu
tPktCnt
The value of
vRtrInetStatRteCpeChkOutPktCnt
indicates the number of echo-request
packets sent.
hostUpDownTime
long
vRtrInetStatRteCpeChkUp
Time
The value of
vRtrInetStatRteCpeChkUpTime indicates
how long (in hundredths of a second) that
the CPE has been available.
ttl
long
vRtrInetStatRteCpeChkTT
L
The value of vRtrInetStatRteCpeChkTTL
indicates the time, in seconds, before the
CPE will be declared down. Upon receipt
of an echo reply, it has the value of
vRtrInetStaticRouteCpeInterval *
vRtrInetStaticRouteCpeDropCnt and is
decremented by 1 every second.
upTransitions
long
vRtrInetStatRteCpeChkUp
Trans
The value of
vRtrInetStatRteCpeChkUpTrans indicates
the number of times the CPE has
transitioned to the available state.
DhcpRelayStats
MIB table name: TIMETRA-VRTR-MIB.vRtrIfDHCPRelayStatsTable
Monitored classes:
• rtr.DhcpRelayConfiguration
• rtr.SubItfDhcpRelayCfg
• rtr.GrpItfDhcpRelayCfg
authPktsDiscarded
long
vRtrIfDHCPRelayAuthPkts
Discarded
vRtrIfDHCPRelayAuthPktsDiscarded
indicates the total number of packets
discarded because authentication was not
successful.
authPktsSuccess
long
vRtrIfDHCPRelayAuthPkts
Success
vRtrIfDHCPRelayAuthPktsSuccess
indicates the total number of packets for
which authentication was successful.
clientPacketsDiscarded
long
vRtrIfDHCPRelayClientPkt
sDiscarded
vRtrIfDHCPRelayClientPktsDiscarded
indicates the total number of client
packets dicarded by the DHCP relay
agent.
clientPacketsRelayed
long
vRtrIfDHCPRelayClientPkt
sRelayed
vRtrIfDHCPRelayClientPktsRelayed
indicates the total number of client
packets relayed by the DHCP relay agent.
(1 of 4)
E-120
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
clientPktsProxLS
long
vRtrIfDHCPRelayClientPkt
sProxLS
vRtrIfDHCPRelayClientPktsProxLS
indicates the total number of client
packets proxied by the DHCP relay agent
based on a lease state. The lease itself
can have been obtained from a DHCP or
RADIUS server. This is the so called lease
split functionality.
clientPktsProxRad
long
vRtrIfDHCPRelayClientPkt
sProxRad
vRtrIfDHCPRelayClientPktsProxRad
indicates the total number of client
packets proxied by the DHCP relay agent
based on data received from a RADIUS
server.
clientPktsProxRad
long
vRtrIfDHCPRelayClientPkt
sSnooped
vRtrIfDHCPRelayClientPktsSnooped
indicates the total number of client
packets snooped by the DHCP relay agent.
pktsGenRelease
long
vRtrIfDHCPRelayPktsGen
Release
vRtrIfDHCPRelayPktsGenRelease
indicates the total number of DHCP
RELEASE messages spoofed by the DHCP
relay agent to the DHCP server.
receivedMalformedPackets
long
vRtrIfDHCPRelayRxMalfor
medPkts
vRtrIfDHCPRelayRxMalformedPkts
indicates the total number of malformed
packets received by the DHCP relay
agent.
receivedPackets
long
vRtrIfDHCPRelayRxPkts
vRtrIfDHCPRelayRxPkts indicates the total
number of packets received by the DHCP
relay agent.
receivedUntrustedPackets
long
vRtrIfDHCPRelayRxUntrus
tedPkts
vRtrIfDHCPRelayRxUntrustedPkts
indicates the total number of untrusted
packets received by the DHCP relay
agent.
serverPacketsDiscarded
long
vRtrIfDHCPRelayServerPk
tsDiscarded
vRtrIfDHCPRelayServerPktsDiscarded
indicates the total number of server
packets discarded by the DHCP relay
agent.
serverPacketsRelayed
long
vRtrIfDHCPRelayServerPk
tsRelayed
vRtrIfDHCPRelayServerPktsRelayed
indicates the total number of server
packets relayed by the DHCP relay agent.
serverPktsSnooped
long
vRtrIfDHCPRelayPktsGenF
orceRenew
vRtrIfDHCPRelayPktsGenForceRenew
indicates the total number of DHCP
FORCERENEW messages spoofed by the
DHCP relay agent to the DHCP clients.
serverPktsSnooped
long
vRtrIfDHCPRelayServerPk
tsSnooped
vRtrIfDHCPRelayServerPktsSnooped
indicates the total number of server
packets snooped by the DHCP relay agent.
transmittedPackets
long
vRtrIfDHCPRelayTxPkts
vRtrIfDHCPRelayTxPkts indicates the total
number of packets transmitted by the
DHCP relay agent.
NetworkInterfaceURPFStats
MIB table name: TIMETRA-VRTR-MIB.vRtrIfStatsTable
Monitored class: rtr.NetworkInterface
uRPFCheckFailPkts
UINT128
vRtrIfuRPFCheckFailPkts
The value of vRtrIfuRPFCheckFailPkts
indicates the number of packets that fail
uRPF check on this interface.
(2 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-121
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
uRPFCheckFailPktsHigh32
long
vRtrIfuRPFCheckFailPktsH
igh32
The value of
vRtrIfuRPFCheckFailPktsHigh32 indicates
the high 32 bits of the value of
vRtrIfuRPFCheckFailPkts.
uRPFCheckFailPktsLow32
long
vRtrIfuRPFCheckFailPktsL
ow32
The value of
vRtrIfuRPFCheckFailPktsLow32 indicates
the lower 32 bits of the value of
vRtrIfuRPFCheckFailPkts.
RouteStats
MIB table name: TIMETRA-VRTR-MIB.vRtrStatTable
Monitored classes:
•
•
rtr.VirtualRouter
vprn.Site
activeARPEntries
long
vRtrStatActiveARPEntries
vRtrStatActiveARPEntries indicates the
number of active ARP entries for the
specified virtual router in the system.
aggregateActiveRoutes
long
vRtrAggregateActiveRout
es
vRtrAggregateActiveRoutes indicates the
current number of active aggregate
routes for this instance of the route table.
aggregateRoutes
long
vRtrAggregateRoutes
vRtrAggregateRoutes indicates the
current number of aggregate routes for
this instance of the route table.
bgpActiveRoutes
long
vRtrBGPActiveRoutes
vRtrBGPActiveRoutes indicates the
current number of active bgp routes for
this instance of the route table.
bgpRoutes
long
vRtrBGPRoutes
vRtrBGPRoutes indicates the current
number of bgp routes for this instance of
the route table.
bgpVpnActiveRoutes
long
vRtrStatBGPVpnActiveRo
utes
vRtrStatBGPVpnActiveRoutes indicates
the current number of active VPN-IPV4
routes learned by MP-BGP for this virtual
router.
bgpVpnRoutes
long
vRtrStatBGPVpnRoutes
vRtrStatBGPVpnRoutes indicates the
current number of VPN-IPV4 routes
learned by MP-BGP for this virtual router.
directActiveRoutes
long
vRtrDirectActiveRoutes
vRtrDirectActiveRoutes indicates the
current number of active direct routes for
this instance of the route table.
directRoutes
long
vRtrDirectRoutes
vRtrDirectRoutes indicates the current
number of direct routes for this instance
of the route table.
illegalLabelsReceived
long
vRtrStatIllegalLabels
vRtrStatIllegalLabels indicates the
number of illegally received labels on this
virtual router.
isisActiveRoutes
long
vRtrISISActiveRoutes
vRtrISISActiveRoutes indicates the
current number of active isis routes for
this instance of the route table.
isisRoutes
long
vRtrISISRoutes
vRtrISISRoutes indicates the current
number of isis routes for this instance of
the route table.
(3 of 4)
E-122
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ldpActiveTunnels
long
vRtrStatActiveLdpTunnels
vRtrStatActiveLdpTunnels indicates the
current number of rows in the
vRtrTunnelTable where vRtrTunnelType
has a value of 'ldp'.
ldpTunnels
long
vRtrStatTotalLdpTunnels
vRtrStatTotalLdpTunnels indicates the
current number of both active and
inactive LDP tunnels.
ospfActiveRoutes
long
vRtrOSPFActiveRoutes
vRtrOSPFActiveRoutes indicates the
current number of active ospf routes for
this instance of the route table.
ospfRoutes
long
vRtrOSPFRoutes
vRtrOSPFRoutes indicates the current
number of ospf routes for this instance of
the route table.
ripActiveRoutes
long
vRtrRIPActiveRoutes
vRtrRIPActiveRoutes indicates the current
number of active rip routes for this
instance of the route table.
ripRoutes
long
vRtrRIPRoutes
vRtrRIPRoutes indicates the current
number of rip routes for this instance of
the route table.
routerInterfacesActive
long
vRtrStatActiveIfs
vRtrStatActiveIfs indicates the current
number of router interfaces with
vRtrIfAdminState equal 'inService' on this
virtual router.
routerInterfacesConfigured
long
vRtrStatConfiguredIfs
vRtrStatConfiguredIfs indicates the
current number of router interfaces
configured on this virtual router.
routesInVrf
long
vRtrStatCurrNumRoutes
vRtrStatCurrNumRoutes indicates the
current number of routes in the VRF for
this virtual router.
sdpActiveTunnels
long
vRtrStatActiveSdpTunnels
vRtrStatActiveSdpTunnels indicates the
current number of rows in the
vRtrTunnelTable where vRtrTunnelType
has a value of 'sdp'.
sdpTunnels
long
vRtrStatTotalSdpTunnels
vRtrStatTotalSdpTunnels indicates the
current number of both active and
inactive SDP tunnels.
staticActiveRoutes
long
vRtrStaticActiveRoutes
vRtrStaticActiveRoutes indicates the
current number of active static routes for
this instance of the route table.
staticRoutes
long
vRtrStaticRoutes
vRtrStaticRoutes indicates the current
number of static routes for this instance
of the route table.
totalARPEntries
long
vRtrStatTotalARPEntries
vRtrStatTotalARPEntries indicates the
total number of active and inactive ARP
entries for the specified virtual router in
the system.
(4 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-123
E. 7450 ESS Release 7.0 statistics counters
Table E-28 service statistics
5620 SAM counter name
Type
MIB counter name
Description
L3AccessInterfaceURPFStats
MIB table name: TIMETRA-VRTR-MIB.vRtrIfStatsTable
Monitored class: service.L3AccessInterface
uRPFCheckFailPkts
UINT128
vRtrIfuRPFCheckFailPkts
The value of vRtrIfuRPFCheckFailPkts
indicates the number of packets that fail
uRPF check on this interface.
uRPFCheckFailPktsHigh32
long
vRtrIfuRPFCheckFailPktsH
igh32
The value of
vRtrIfuRPFCheckFailPktsHigh32 indicates
the high 32 bits of the value of
vRtrIfuRPFCheckFailPkts.
uRPFCheckFailPktsLow32
long
vRtrIfuRPFCheckFailPktsL
ow32
The value of
vRtrIfuRPFCheckFailPktsLow32 indicates
the lower 32 bits of the value of
vRtrIfuRPFCheckFailPkts.
SapBaseStats
MIB table name: TIMETRA-SAP-MIB.sapBaseStatsTable
Monitored classes:
• service.L2AccessInterface
• service.L3AccessInterface
authenticationPacketsDiscarded
long
sapBaseStatsAuthenticati
onPktsDiscarded
The number of DHCP packets discarded as
result of authentication.
authenticationPacketsSuccessful
long
sapBaseStatsAuthenticati
onPktsSuccess
The number of DHCP packets successfully
authenticated.
customerId
long
sapBaseStatsCustId
The Customer ID for the associated
service.
egressQChipDroppedInProfOctets
UINT128
sapBaseStatsEgressQchip
DroppedInProfOctets
The number of in-profile octets discarded
by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
egressQChipDroppedInProfPackets
UINT128
sapBaseStatsEgressQchip
DroppedInProfPackets
The number of in-profile packets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
egressQChipDroppedOutProfOctets
UINT128
sapBaseStatsEgressQchip
DroppedOutProfOctets
The number of out-of-profile packets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
egressQChipDroppedOutProfPacke
ts
UINT128
sapBaseStatsEgressQchip
DroppedOutProfPackets
The number of out-of-profile packets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
egressQChipForwardedInProfOctet
s
UINT128
sapBaseStatsEgressQchip
ForwardedInProfOctets
The number of in-profile octets (rate
below CIR) forwarded by the egress
Qchip.
egressQChipForwardedInProfPacke
ts
UINT128
sapBaseStatsEgressQchip
ForwardedInProfPackets
The number of in-profile packets (rate
below CIR) forwarded by the egress
Qchip.
egressQChipForwardedOutProfOct
ets
UINT128
sapBaseStatsEgressQchip
ForwardedOutProfOctets
The number of out-of-profile octets (rate
above CIR) forwarded by the egress
Qchip.
(1 of 28)
E-124
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
egressQChipForwardedOutProfPac
kets
UINT128
sapBaseStatsEgressQchip
ForwardedOutProfPacket
s
The number of out-of-profile packets
(rate above CIR) forwarded by the egress
Qchip.
ingressPChipDroppedOctets
UINT128
sapBaseStatsIngressPchip
DroppedOctets
The number of octets dropped by the
ingress Pchip due to: SAP state, ingress
MAC, IP or IPv6 filter, same segment
discard, bad checksum, etc.
ingressPChipDroppedPackets
UINT128
sapBaseStatsIngressPchip
DroppedPackets
The number of packets dropped by the
ingress Pchip due to: SAP state, ingress
MAC, IP or IPv6 filter, same segment
discard, bad checksum, etc.
ingressPChipOfferedHiPrioOctets
UINT128
sapBaseStatsIngressPchip
OfferedHiPrioOctets
The number of high priority octets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
ingressPChipOfferedHiPrioPackets
UINT128
sapBaseStatsIngressPchip
OfferedHiPrioPackets
The number of high priority packets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
ingressPChipOfferedLoPrioOctets
UINT128
sapBaseStatsIngressPchip
OfferedLoPrioOctets
The number of low priority octets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
ingressPChipOfferedLoPrioPackets
UINT128
sapBaseStatsIngressPchip
OfferedLoPrioPackets
The number of low priority packets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
ingressPChipOfferedUncoloredOct
ets
UINT128
sapBaseStatsIngressPchip
OfferedUncoloredOctets
The number of uncolored octets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
ingressPChipOfferedUncoloredPac
kets
UINT128
sapBaseStatsIngressPchip
OfferedUncoloredPackets
The number of uncolored packets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
ingressQChipDroppedHiPrioOctets
UINT128
sapBaseStatsIngressQchip
DroppedHiPrioOctets
The number of high priority octets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
ingressQChipDroppedHiPrioPacket
s
UINT128
sapBaseStatsIngressQchip
DroppedHiPrioPackets
The number of high priority packets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
ingressQChipDroppedLoPrioOctets
UINT128
sapBaseStatsIngressQchip
DroppedLoPrioOctets
The number of low priority octets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
ingressQChipDroppedLoPrioPacket
s
UINT128
sapBaseStatsIngressQchip
DroppedLoPrioPackets
The number of low priority packets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
ingressQChipForwardedInProfOcte
ts
UINT128
sapBaseStatsIngressQchip
ForwardedInProfOctets
The number of in-profile octets (rate
below CIR) forwarded by the ingress
Qchip.
(2 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-125
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingressQChipForwardedInProfPack
ets
UINT128
sapBaseStatsIngressQchip
ForwardedInProfPackets
The number of in-profile packets (rate
below CIR) forwarded by the ingress
Qchip.
ingressQChipForwardedOutProfOct
ets
UINT128
sapBaseStatsIngressQchip
ForwardedOutProfOctets
The number of out-of-profile octets (rate
above CIR) forwarded by the ingress
Qchip.
ingressQChipForwardedOutProfPac
kets
UINT128
sapBaseStatsIngressQchip
ForwardedOutProfPacket
s
The number of out-of-profile packets
(rate above CIR) forwarded by the ingress
Qchip.
SapEgrQosHsmdaCntrStats
MIB table name: TIMETRA-SAP-MIB.sapEgrQosHsmdaCntrStatsTable
Monitored classes:
•
•
•
service.L2AccessInterface
service.L3AccessInterface
service.ServiceAccessPoint
sapEgrHsmdaCntrStCounterId
long
sapEgrHsmdaCntrStCntrId
The value of sapEgrHsmdaCntrStCntrId
indicates the counter ID for the statistics.
sapEgrHsmdaCntrStCustomerId
long
sapEgrHsmdaCntrStCustId
The value of sapEgrHsmdaCntrStCustId
indicates the customer ID for the
statistics.
sapEgrHsmdaCntrStInProfileOctets
Fwd
UINT128
sapEgrHsmdaCntrStInProf
OctFwd
The value of
sapEgrHsmdaCntrStInProfOctFwd
indicates the number of out-of-profile
packets forwarded for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapEgrHsmdaCntrStInProfilePacket
sDropped
UINT128
sapEgrHsmdaCntrStInProf
PktDrop
The value of
sapEgrHsmdaCntrStInProfPktDrop
indicates the number of in-profile packets
dropped for the egress counter, specified
by the index sapIngHsmdaCntrStCntrId,
on this SAP.
sapEgrHsmdaCntrStInProfilePacket
sFwd
UINT128
sapEgrHsmdaCntrStInProf
PktFwd
The value of
sapEgrHsmdaCntrStInProfPktFwd
indicates the number of in-profile packets
forwarded for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapEgrHsmdaCntrStInProfOctetsDr
opped
UINT128
sapEgrHsmdaCntrStInProf
OctDrop
The value of
sapEgrHsmdaCntrStInProfOctDrop
indicates the number of out-of-profile
packets dropped for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapEgrHsmdaCntrStOutProfileOcte
tsDropped
UINT128
sapEgrHsmdaCntrStOutPr
ofOctDrop
The value of
sapEgrHsmdaCntrStOutProfOctDrop
indicates the number of out-of-profile
packets dropped for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
(3 of 28)
E-126
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapEgrHsmdaCntrStOutProfileOcte
tsFwd
UINT128
sapEgrHsmdaCntrStOutPr
ofOctFwd
The value of
sapEgrHsmdaCntrStOutProfOctFwd
indicates the number of out-of-profile
packets forwarded for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapEgrHsmdaCntrStOutProfilePack
etsDropped
UINT128
sapEgrHsmdaCntrStOutPr
ofPktDrop
The value of
sapEgrHsmdaCntrStOutProfPktDrop
indicates the number of out-of-profile
packets dropped for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapEgrHsmdaCntrStOutProfilePack
etsFwd
UINT128
sapEgrHsmdaCntrStOutPr
ofPktFwd
The value of
sapEgrHsmdaCntrStOutProfPktFwd
indicates the number of out-of-profile
packets forwarded for the egress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
SapEgrQosHsmdaQueueStats
MIB table name: TIMETRA-SAP-MIB.sapEgrQosHsmdaQueueStatsTable
Monitored classes:
•
•
•
service.L2AccessInterface
service.L3AccessInterface
service.ServiceAccessPoint
sapEgrHsmdaQStatCustomerId
long
sapEgrHsmdaQStatCustId
The value of sapEgrHsmdaQStatCustId
indicates the customer ID for the
statistics.
sapEgrHsmdaQStatInProfileOctets
Dropped
UINT128
sapEgrHsmdaQStatInProf
OctDropd
The value of
sapEgrHsmdaQStatInProfOctDropd
indicates the number of out-of-profile
packets dropped on egress on this SAP.
sapEgrHsmdaQStatInProfileOctetsF
wd
UINT128
sapEgrHsmdaQStatInProf
OctFwd
The value of
sapEgrHsmdaQStatInProfOctFwd
indicates the number of out-of-profile
packets forwarded on egress on this SAP.
sapEgrHsmdaQStatInProfilePackets
Dropped
UINT128
sapEgrHsmdaQStatInProf
PktDropd
The value of
sapEgrHsmdaQStatInProfPktDropd
indicates the number of in-profile packets
dropped on egress on this SAP.
sapEgrHsmdaQStatInProfilePackets
Fwd
UINT128
sapEgrHsmdaQStatInProf
PktFwd
The value of
sapEgrHsmdaQStatInProfPktFwd indicates
the number of in-profile packets
forwarded on egress on this SAP.
sapEgrHsmdaQStatOutProfileOctet
sDropped
UINT128
sapEgrHsmdaQStatOutPro
fOctDropd
The value of
sapEgrHsmdaQStatOutProfOctDropd
indicates the number of out-of-profile
packets dropped on egress on this SAP.
sapEgrHsmdaQStatOutProfileOctet
sFwd
UINT128
sapEgrHsmdaQStatOutPro
fOctFwd
The value of
sapEgrHsmdaQStatOutProfOctFwd
indicates the number of out-of-profile
packets forwarded on egress on this SAP.
sapEgrHsmdaQStatOutProfilePacke
tsDropped
UINT128
sapEgrHsmdaQStatOutPro
fPktDropd
The value of
sapEgrHsmdaQStatOutProfPktDropd
indicates the number of out-of-profile
packets dropped on egress on this SAP.
(4 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-127
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapEgrHsmdaQStatOutProfilePacke
tsFwd
UINT128
sapEgrHsmdaQStatOutPro
fPktFwd
The value of
sapEgrHsmdaQStatOutProfPktFwd
indicates the number of out-of-profile
packets forwarded on egress on this SAP.
sapEgrHsmdaQStatQueueId
long
sapEgrQosHsmdaQueueId
The value of sapEgrQosHsmdaQueueId
index specifies the Hsmda egress queue
which this override record will affect.
SapEgrQosPlcyQueueStats
MIB table name: TIMETRA-SAP-MIB.sapEgrQosPlcyQueueStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
droppedInProfOctets
UINT128
sapEgQosPlcyQueueStats
DroppedInProfOctets
The value of
sapEgQosPlcyQueueStatsDroppedInProfOc
tets indicates the number in-profile
octets discarded by the egress Qchip due
to: MBS exceeded, buffer pool limit
exceeded, etc.
droppedInProfPackets
UINT128
sapEgQosPlcyQueueStats
DroppedInProfPackets
The value of
sapEgQosPlcyQueueStatsDroppedInProfPa
ckets indicates the number of in-profile
packets discarded by the egress Qchip due
to: MBS exceeded, buffer pool limit
exceeded, etc.
droppedOutProfOctets
UINT128
sapEgQosPlcyQueueStats
DroppedOutProfOctets
The value of
sapEgQosPlcyQueueStatsDroppedOutProf
Octets indicates the number
out-of-profile octets discarded by the
egress Qchip due to: MBS exceeded,
buffer pool limit exceeded, etc.
droppedOutProfPackets
UINT128
sapEgQosPlcyQueueStats
DroppedOutProfPackets
The value of
sapEgQosPlcyQueueStatsDroppedOutProf
Packets indicates the number
out-of-profile packets discarded by the
egress Qchip due to: MBS exceeded,
buffer pool limit exceeded, etc.
forwardedInProfOctets
UINT128
sapEgQosPlcyQueueStats
ForwardedInProfOctets
The value of
sapEgQosPlcyQueueStatsForwardedInProf
Octets indicates the number ofin-profile
octets (rate below CIR) forwarded by the
egress Qchip.
forwardedInProfPackets
UINT128
sapEgQosPlcyQueueStats
ForwardedInProfPackets
The value of
sapEgQosPlcyQueueStatsForwardedInProf
Packets indicates the number of in-profile
packets (rate below CIR) forwarded by the
egress Qchip.
forwardedOutProfOctets
UINT128
sapEgQosPlcyQueueStats
ForwardedOutProfOctets
The value of
sapEgQosPlcyQueueStatsForwardedOutPr
ofOctets indicates the number of
out-of-profile octets (rate above CIR)
forwarded by the egress Qchip.
forwardedOutProfPackets
UINT128
sapEgQosPlcyQueueStats
ForwardedOutProfPacket
s
The value of
sapEgQosPlcyQueueStatsForwardedOutPr
ofPackets indicates the number of
out-of-profile packets (rate above CIR)
forwarded by the egress Qchip.
(5 of 28)
E-128
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
policyId
long
sapEgQosPlcyQueuePlcyId
The row index in the tSapEgressTable
corresponding to this egress QoS policy.
queueId
long
sapEgQosPlcyQueueId
The value of sapEgQosPlcyQueueId
indicates index of the egress QoS queue of
this SAP.
SapEgrQosPlcyStats
MIB table name: TIMETRA-SAP-MIB.sapEgrQosPlcyStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
droppedInProfOctets
UINT128
sapEgQosPlcyDroppedInPr
ofOctets
The value of the object
sapEgQosPlcyDroppedInProfOctets
indicates the number of in-profile octets,
as determined by the SAP egress QoS
policy, dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedInProfPackets
UINT128
sapEgQosPlcyDroppedInPr
ofPackets
The value of the object
sapEgQosPlcyDroppedInProfPackets
indicates the number of in-profile
packets, as determined by the SAP egress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
droppedOutProfOctets
UINT128
sapEgQosPlcyDroppedOut
ProfOctets
The value of the object
sapEgQosPlcyDroppedOutProfOctets
indicates the number of out-profile
octets, as determined by the SAP egress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
droppedOutProfPackets
UINT128
sapEgQosPlcyDroppedOut
ProfPackets
The value of the object
sapEgQosPlcyDroppedOutProfPackets
indicates the number of out-profile
packets, as determined by the SAP egress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
forwardedInProfOctets
UINT128
sapEgQosPlcyForwardedI
nProfOctets
The value of the object
sapEgQosPlcyForwardedInProfOctets
indicates the number of in-profile octets
(rate below CIR) forwarded by the egress
Qchip.
forwardedInProfPackets
UINT128
sapEgQosPlcyForwardedI
nProfPackets
The value of the object
sapEgQosPlcyForwardedInProfPackets
indicates the number of in-profile packets
(rate below CIR) forwarded by the egress
Qchip.
forwardedOutProfOctets
UINT128
sapEgQosPlcyForwardedO
utProfOctets
The value of the object
sapEgQosPlcyForwardedOutProfOctets
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
egress Qchip.
(6 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-129
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
forwardedOutProfPackets
UINT128
sapEgQosPlcyForwardedO
utProfPackets
The value of the object
sapEgQosPlcyForwardedOutProfPackets
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
egress Qchip.
policyId
long
sapEgQosPlcyId
The value of the object sapEgQosPlcyId
indicates the row index in the
tSapEgressTable corresponding to this
egress QoS policy, or one if no policy is
specified.
SapEgrQosQueueStats
MIB table name: TIMETRA-SAP-MIB.sapEgrQosQueueStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
customerId
long
sapEgrQosCustId
The Customer ID for the associated
service.
droppedInProfOctets
UINT128
sapEgrQosQueueStatsDro
ppedInProfOctets
The number of in-profile octets discarded
by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedInProfPackets
UINT128
sapEgrQosQueueStatsDro
ppedInProfPackets
The number of in-profile packets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedOutProfOctets
UINT128
sapEgrQosQueueStatsDro
ppedOutProfOctets
The number of out-of-profile octets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedOutProfPackets
UINT128
sapEgrQosQueueStatsDro
ppedOutProfPackets
The number of out-of-profile packets
discarded by the egress Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
forwardedInProfOctets
UINT128
sapEgrQosQueueStatsFor
wardedInProfOctets
The number of in-profile octets (rate
below CIR) forwarded by the egress
Qchip.
forwardedInProfPackets
UINT128
sapEgrQosQueueStatsFor
wardedInProfPackets
The number of in-profile packets (rate
below CIR) forwarded by the egress
Qchip.
forwardedOutProfOctets
UINT128
sapEgrQosQueueStatsFor
wardedOutProfOctets
The number of out-of-profile octets (rate
above CIR) forwarded by the egress
Qchip.
forwardedOutProfPackets
UINT128
sapEgrQosQueueStatsFor
wardedOutProfPackets
The number of out-of-profile packets
(rate above CIR) forwarded by the egress
Qchip.
queueId
long
sapEgrQosQueueId
The index of the egress QoS queue of this
SAP.
SapEgrQosSchedStats
MIB table name: TIMETRA-SAP-MIB.sapEgrQosSchedStatsTable
Monitored classes:
service.L2AccessInterface
service.L3AccessInterface
•
•
(7 of 28)
E-130
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
customerId
long
sapEgrQosSchedCustId
The Customer ID for the associated
service.
forwardedOctets
UINT128
sapEgrQosSchedStatsForw
ardedOctets
The number of forwarded octets by the
egress Qchip, as determined by the SAP
egress scheduler policy.
forwardedPackets
UINT128
sapEgrQosSchedStatsForw
ardedPackets
The number of forwarded packets by the
egress Qchip, as determined by the SAP
egress scheduler policy.
qosSchedName
String
sapEgrQosSchedName
The index of the egress QoS scheduler of
this SAP.
SapEgrSchedPlcyPortStats
MIB table name: TIMETRA-SAP-MIB.sapEgrSchedPlcyPortStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
forwardedOctets
UINT128
sapEgrSchedPlcyPortStats
FwdOct
The value of
sapEgrSchedPlcyPortStatsFwdOct
indicates the number of forwarded
octets,as determined by the SAP egress
scheduler policy, offered by the Pchip to
the Qchip.
forwardedPackets
UINT128
sapEgrSchedPlcyPortStats
FwdPkt
The value of
sapEgrSchedPlcyPortStatsFwdPkt
indicates the number of forwarded
packets, as determined by the SAP egress
scheduler policy, offered by the Pchip to
the Qchip.
SapEgrSchedPlcyStats
MIB table name: TIMETRA-SAP-MIB.sapEgrSchedPlcyStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
forwardedOctets
UINT128
sapEgrSchedPlcyStatsFwd
Oct
The number of octets forwarded by the
egress Qchip, as determined by the SAP
egress scheduler policy.
forwardedPackets
UINT128
sapEgrSchedPlcyStatsFwd
Pkt
The number of packets forwarded by the
egress Qchip, as determined by the SAP
egress scheduler policy.
SapIngQosHsmdaCntrStats
MIB table name: TIMETRA-SAP-MIB.sapIngQosHsmdaCntrStatsTable
Monitored classes:
•
•
•
service.L2AccessInterface
service.L3AccessInterface
service.ServiceAccessPoint
sapIngHsmdaCntrStAllOctetsOffere
d
UINT128
sapIngHsmdaCntrStAllOct
Offered
The value of
sapIngHsmdaCntrStAllOctOffered
indicates the total number of octets
offered on ingress on this SAP.
sapIngHsmdaCntrStAllPacketsOffer
ed
UINT128
sapIngHsmdaCntrStAllPkt
Offered
The value of
sapIngHsmdaCntrStAllPktOffered
indicates the total number of packets
offered on ingress on this SAP.
(8 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-131
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapIngHsmdaCntrStCounterId
long
sapIngHsmdaCntrStCntrId
The value of sapIngHsmdaCntrStCntrId
indicates the counter ID for the statistics.
sapIngHsmdaCntrStCusomerId
long
sapIngHsmdaCntrStCustId
The value of sapIngHsmdaCntrStCustId
indicates the customer ID for the
statistics.
sapIngHsmdaCntrStHiOctetsDropp
ed
UINT128
sapIngHsmdaCntrStHiOct
Drop
The value of
sapIngHsmdaCntrStHiOctDrop indicates
the number of high-priority octets
dropped for the ingress counter, specified
by the index sapIngHsmdaCntrStCntrId,
on this SAP.
sapIngHsmdaCntrStHiPacketsDrop
ped
UINT128
sapIngHsmdaCntrStHiPkt
Drop
The value of
sapIngHsmdaCntrStHiPktDrop indicates
the number of high-priority packets
dropped for the ingress counter, specified
by the index sapIngHsmdaCntrStCntrId,
on this SAP.
sapIngHsmdaCntrStInProfileOctets
Fwd
UINT128
sapIngHsmdaCntrStInProf
OctFwd
The value of
sapIngHsmdaCntrStInProfOctFwd
indicates the number of out-of-profile
packets forwarded for the ingress
counter, specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapIngHsmdaCntrStInProfilePacket
sFwd
UINT128
sapIngHsmdaCntrStInProf
PktFwd
The value of
sapIngHsmdaCntrStInProfPktFwd
indicates the number of in-profile packets
forwarded for the ingress counter,
specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapIngHsmdaCntrStLoOctetsDropp
ed
UINT128
sapIngHsmdaCntrStLoOct
Drop
The value of
sapIngHsmdaCntrStLoOctDrop indicates
the number of low-priority octets
dropped for the ingress counter, specified
by the index sapIngHsmdaCntrStCntrId,
on this SAP.
sapIngHsmdaCntrStLoPacketsDrop
ped
UINT128
sapIngHsmdaCntrStLoPkt
Drop
The value of
sapIngHsmdaCntrStLoPktDrop indicates
the number of low-priority packets
dropped for the ingress counter, specified
by the index sapIngHsmdaCntrStCntrId,
on this SAP.
sapIngHsmdaCntrStOutProfileOcte
tsFwd
UINT128
sapIngHsmdaCntrStOutPr
ofOctFwd
The value of
sapIngHsmdaCntrStOutProfOctFwd
indicates the number of out-of-profile
packets forwarded for the ingress
counter, specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
sapIngHsmdaCntrStOutProfilePack
etsFwd
UINT128
sapIngHsmdaCntrStOutPr
ofPktFwd
The value of
sapIngHsmdaCntrStOutProfPktFwd
indicates the number of out-of-profile
packets forwarded for the ingress
counter, specified by the index
sapIngHsmdaCntrStCntrId, on this SAP.
(9 of 28)
E-132
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
SapIngQosHsmdaQueueStats
MIB table name: TIMETRA-SAP-MIB.sapIngQosHsmdaQueueStatsTable
Monitored classes:
•
•
•
service.L2AccessInterface
service.L3AccessInterface
service.ServiceAccessPoint
sapIngHsmdaQStatAllOctetsOffere
d
UINT128
sapIngHsmdaQStatAllOcts
Offered
The value of
sapIngHsmdaQStatAllOctsOffered
indicates the total number of octets
offered on ingress on this SAP.
sapIngHsmdaQStatAllPacketsOffer
ed
UINT128
sapIngHsmdaQStatAllPkts
Offered
The value of
sapIngHsmdaQStatAllPktsOffered
indicates the total number of packets
offered on ingress on this SAP.
sapIngHsmdaQStatCustomerId
long
sapIngHsmdaQStatCustId
The value of sapIngHsmdaQStatCustId
indicates the customer ID for the
statistics.
sapIngHsmdaQStatHiOctetsDroppe
d
UINT128
sapIngHsmdaQStatHiOcts
Dropped
The value of
sapIngHsmdaQStatHiOctsDropped
indicates the number of high-priority
octets dropped on ingress on this SAP.
sapIngHsmdaQStatHiPacketsDropp
ed
UINT128
sapIngHsmdaQStatHiPkts
Dropped
The value of
sapIngHsmdaQStatHiPktsDropped
indicates the number of high-priority
packets dropped on ingress on this SAP.
sapIngHsmdaQStatInProfileOctetsF
wd
UINT128
sapIngHsmdaQStatInProf
OctsFwd
The value of
sapIngHsmdaQStatInProfOctsFwd
indicates the number of out-of-profile
packets forwarded on ingress on this SAP.
sapIngHsmdaQStatInProfilePackets
Fwd
UINT128
sapIngHsmdaQStatInProfP
ktsFwd
The value of
sapIngHsmdaQStatInProfPktsFwd
indicates the number of in-profile packets
forwarded on ingress on this SAP.
sapIngHsmdaQStatLoOctetsDroppe
d
UINT128
sapIngHsmdaQStatLoOcts
Dropped
The value of
sapIngHsmdaQStatLoOctsDropped
indicates the number of low-priority
octets dropped on ingress on this SAP.
sapIngHsmdaQStatLoPacketsDropp
ed
UINT128
sapIngHsmdaQStatLoPkts
Dropped
The value of
sapIngHsmdaQStatLoPktsDropped
indicates the number of low-priority
packets dropped on ingress on this SAP.
sapIngHsmdaQStatOutProfileOctet
sFwd
UINT128
sapIngHsmdaQStatOutPro
fOctsFwd
The value of
sapIngHsmdaQStatOutProfOctsFwd
indicates the number of out-of-profile
packets forwarded on ingress on this SAP.
sapIngHsmdaQStatOutProfilePacke
tsFwd
UINT128
sapIngHsmdaQStatOutPro
fPktsFwd
The value of
sapIngHsmdaQStatOutProfPktsFwd
indicates the number of out-of-profile
packets forwarded on ingress on this SAP.
sapIngHsmdaQStatQueueId
long
sapIngQosHsmdaQueueId
The value of sapIngQosHsmdaQueueId
index specifies the Hsmda egress queue
which this override record will affect.
(10 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-133
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
SapIngQosPlcyQueueStats
MIB table name: TIMETRA-SAP-MIB.sapIngQosPlcyQueueStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
droppedHiPrioOctets
UINT128
sapIgQosPlcyQueueStatsD
roppedHiPrioOctets
The value of
sapIgQosPlcyQueueStatsDroppedHiPrioOc
tets indicates the number of high priority
octets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
droppedHiPrioPackets
UINT128
sapIgQosPlcyQueueStatsD
roppedHiPrioPackets
The value of
sapIgQosPlcyQueueStatsDroppedHiPrioPa
ckets indicates the number of high
priority packets, as determined by the
SAP ingress QoS policy, dropped by the
Qchip due to: MBS exceeded, buffer pool
limit exceeded, etc.
droppedLoPrioOctets
UINT128
sapIgQosPlcyQueueStatsD
roppedLoPrioOctets
The value of
sapIgQosPlcyQueueStatsDroppedLoPrioOc
tets indicates the number of low priority
octets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
droppedLoPrioPackets
UINT128
sapIgQosPlcyQueueStatsD
roppedLoPrioPackets
The value of
sapIgQosPlcyQueueStatsDroppedLoPrioPa
ckets indicates the number of low priority
packets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
forwardedInProfOctets
UINT128
sapIgQosPlcyQueueStatsF
orwardedInProfOctets
The value of
sapIgQosPlcyQueueStatsForwardedInProf
Octets indicates the number of in-profile
octets (rate below CIR) forwarded by the
ingress Qchip.
forwardedInProfPackets
UINT128
sapIgQosPlcyQueueStatsF
orwardedInProfPackets
The value of
sapIgQosPlcyQueueStatsForwardedInProf
Packets indicates the number of in-profile
packets (rate below CIR) forwarded by the
ingress Qchip.
forwardedOutProfOctets
UINT128
sapIgQosPlcyQueueStatsF
orwardedOutProfOctets
The value of
sapIgQosPlcyQueueStatsForwardedOutPro
fOctets indicates the number of
out-of-profile octets (rate above CIR)
forwarded by the ingress Qchip.
forwardedOutProfPackets
UINT128
sapIgQosPlcyQueueStatsF
orwardedOutProfPackets
The value of
sapIgQosPlcyQueueStatsForwardedOutPro
fPackets indicates the number of
out-of-profile packets (rate above CIR)
forwarded by the ingress Qchip.
(11 of 28)
E-134
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
offeredHiPrioOctets
UINT128
sapIgQosPlcyQueueStatsO
fferedHiPrioOctets
The value of
sapIgQosPlcyQueueStatsOfferedHiPrioOct
ets indicates the number of high priority
octets, as determined by the SAP ingress
QoS policy, offered by the Pchip to the
Qchip.
offeredHiPrioPackets
UINT128
sapIgQosPlcyQueueStatsO
fferedHiPrioPackets
The value of
sapIgQosPlcyQueueStatsOfferedHiPrioPac
kets indicates the number of high priority
packets, as determined by the SAP ingress
QoS policy, offered by the Pchip to the
Qchip.
offeredLoPrioOctets
UINT128
sapIgQosPlcyQueueStatsO
fferedLoPrioOctets
The value of
sapIgQosPlcyQueueStatsOfferedLoPrioOct
ets indicates the number of low priority
octets, as determined by the SAP ingress
QoS policy, offered by the Pchip to the
Qchip.
offeredLoPrioPackets
UINT128
sapIgQosPlcyQueueStatsO
fferedLoPrioPackets
The value of
sapIgQosPlcyQueueStatsOfferedLoPrioPac
kets indicates the number of low priority
packets, as determined by the SAP ingress
QoS policy, offered by the Pchip to the
Qchip.
policyId
long
sapIgQosPlcyQueuePlcyId
The value of the object
sapIgQosPlcyQueuePlcyId indicates the
row index in the tSapIngressTable
corresponding to this ingress QoS policy.
queueId
long
sapIgQosPlcyQueueId
The index of the ingress QoS queue of this
SAP used by the policy indicated by
sapIgQosPlcyQueuePlcyId.
uncoloredOctetsOffered
UINT128
sapIgQosPlcyQueueStatsU
ncoloredOctetsOffered
The value of
sapIgQosPlcyQueueStatsUncoloredOctets
Offered indicates the number of
uncolored octets offered to the ingress
Qchip.
uncoloredPacketsOffered
UINT128
sapIgQosPlcyQueueStatsU
ncoloredPacketsOffered
The value of
sapIgQosPlcyQueueStatsUncoloredPacket
sOffered indicates the number of
uncolored packets offered to the ingress
Qchip.
SapIngQosPlcyStats
MIB table name: TIMETRA-SAP-MIB.sapIngrQosPlcyStatsTable
Monitored classes:
service.L2AccessInterface
service.L3AccessInterface
•
•
droppedHiPrioOctets
UINT128
sapIgQosPlcyDroppedHiPr
ioOctets
The value of the object
sapIgQosPlcyDroppedHiPrioOctets
indicates the number of high priority
octets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
(12 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-135
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
droppedHiPrioPackets
UINT128
sapIgQosPlcyDroppedHiPr
ioPackets
The value of the object
sapIgQosPlcyDroppedHiPrioPackets
indicates the number of high priority
packets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
droppedLoPrioOctets
UINT128
sapIgQosPlcyDroppedLoPr
ioOctets
The value of the object
sapIgQosPlcyDroppedLoPrioOctets
indicates the number of low priority
octets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
droppedLoPrioPackets
UINT128
sapIgQosPlcyDroppedLoPr
ioPackets
The value of the object
sapIgQosPlcyDroppedLoPrioPackets
indicates the number of low priority
packets, as determined by the SAP ingress
QoS policy, dropped by the Qchip due to:
MBS exceeded, buffer pool limit
exceeded, etc.
forwardedInProfOctets
UINT128
sapIgQosPlcyForwardedIn
ProfOctets
The value of the object
sapIgQosPlcyForwardedInProfOctets
indicates the number of in-profile octets
(rate below CIR) forwarded by the ingress
Qchip.
forwardedInProfPackets
UINT128
sapIgQosPlcyForwardedIn
ProfPackets
The value of the object
sapIgQosPlcyForwardedInProfPackets
indicates the number of in-profile packets
(rate below CIR) forwarded by the ingress
Qchip.
forwardedOutProfOctets
UINT128
sapIgQosPlcyForwardedO
utProfOctets
The value of the object
sapIgQosPlcyForwardedOutProfOctets
indicates the number of out-of-profile
octets (rate above CIR) forwarded by the
ingress Qchip.
forwardedOutProfPackets
UINT128
sapIgQosPlcyForwardedO
utProfPackets
The value of the object
sapIgQosPlcyForwardedOutProfPackets
indicates the number of out-of-profile
packets (rate above CIR) forwarded by the
ingress Qchip.
policyId
long
sapIgQosPlcyId
The value of the object sapIgQosPlcyId
indicates the row index in the
tSapIngressTable corresponding to this
ingress QoS policy, or one if no policy is
specified.
SapIngQosQueueStats
MIB table name: TIMETRA-SAP-MIB.sapIngQosQueueStatsTable
Monitored classes:
service.L2AccessInterface
service.L3AccessInterface
•
•
customerId
long
sapIngQosCustId
The Customer ID for the associated
service.
(13 of 28)
E-136
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
droppedHiPrioOctets
UINT128
sapIngQosQueueStatsDro
ppedHiPrioOctets
The number of high priority octets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedHiPrioPackets
UINT128
sapIngQosQueueStatsDro
ppedHiPrioPackets
The number of high priority packets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedLoPrioOctets
UINT128
sapIngQosQueueStatsDro
ppedLoPrioOctets
The number of low priority octets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
droppedLoPrioPackets
UINT128
sapIngQosQueueStatsDro
ppedLoPrioPackets
The number of low priority packets, as
determined by the SAP ingress QoS policy,
dropped by the Qchip due to: MBS
exceeded, buffer pool limit exceeded,
etc.
forwardedInProfOctets
UINT128
sapIngQosQueueStatsFor
wardedInProfOctets
The number of in-profile octets (rate
below CIR) forwarded by the ingress
Qchip.
forwardedInProfPackets
UINT128
sapIngQosQueueStatsFor
wardedInProfPackets
The number of in-profile packets (rate
below CIR) forwarded by the ingress
Qchip.
forwardedOutProfOctets
UINT128
sapIngQosQueueStatsFor
wardedOutProfOctets
The number of out-of-profile octets (rate
above CIR) forwarded by the ingress
Qchip.
forwardedOutProfPackets
UINT128
sapIngQosQueueStatsFor
wardedOutProfPackets
The number of out-of-profile packets
(rate above CIR) forwarded by the ingress
Qchip.
offeredHiPrioOctets
UINT128
sapIngQosQueueStatsOffe
redHiPrioOctets
The number of high priority octets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
offeredHiPrioPackets
UINT128
sapIngQosQueueStatsOffe
redHiPrioPackets
The number of high priority packets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
offeredLoPrioOctets
UINT128
sapIngQosQueueStatsOffe
redLoPrioOctets
The number of low priority octets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
offeredLoPrioPackets
UINT128
sapIngQosQueueStatsOffe
redLoPrioPackets
The number of low priority packets, as
determined by the SAP ingress QoS policy,
offered by the Pchip to the Qchip.
queueId
long
sapIngQosQueueId
The index of the ingress QoS queue of this
SAP.
uncoloredOctetsOffered
UINT128
sapIngQosQueueStatsUnc
oloredOctetsOffered
The number of uncolored octets offered
to the ingress Qchip.
uncoloredPacketsOffered
UINT128
sapIngQosQueueStatsUnc
oloredPacketsOffered
The number of uncolored packets offered
to the ingress Qchip.
(14 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-137
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
SapIngQosSchedStats
MIB table name: TIMETRA-SAP-MIB.sapIngQosSchedStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
customerId
long
sapIngQosSchedCustId
The Customer ID for the associated
service.
forwardedOctets
UINT128
sapIngQosSchedStatsForw
ardedOctets
The number of forwarded octets, as
determined by the SAP ingress scheduler
policy, offered by the Pchip to the Qchip.
forwardedPackets
UINT128
sapIngQosSchedStatsForw
ardedPackets
The number of forwarded packets, as
determined by the SAP ingress scheduler
policy, offered by the Pchip to the Qchip.
qosSchedName
String
sapIngQosSchedName
The index of the ingress QoS scheduler of
this SAP.
SapIngSchedPlcyPortStats
MIB table name: TIMETRA-SAP-MIB.sapIngSchedPlcyPortStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
forwardedOctets
UINT128
sapIngSchedPlcyPortStats
FwdOct
The value of
sapIngSchedPlcyPortStatsFwdOct
indicates the number of forwarded
octets,as determined by the SAP ingress
scheduler policy, offered by the Pchip to
the Qchip.
forwardedPackets
UINT128
sapIngSchedPlcyPortStats
FwdPkt
The value of
sapIngSchedPlcyPortStatsFwdPkt
indicates the number of forwarded
packets, as determined by the SAP ingress
scheduler policy, offered by the Pchip to
the Qchip.
SapIngSchedPlcyStats
MIB table name: TIMETRA-SAP-MIB.sapIngSchedPlcyStatsTable
Monitored classes:
•
•
service.L2AccessInterface
service.L3AccessInterface
forwardedOctets
UINT128
sapIngSchedPlcyStatsFwd
Oct
The number of forwarded octets, as
determined by the SAP ingress scheduler
policy, offered by the Pchip to the Qchip.
forwardedPackets
UINT128
sapIngSchedPlcyStatsFwd
Pkt
The number of forwarded packets, as
determined by the SAP ingress scheduler
policy, offered by the Pchip to the Qchip.
VdoGrpSrcAdiStats
MIB table name: TIMETRA-VIDEO-MIB.tmnxVdoSGAdiStatTable
Monitored class: service.ZoneAdiChl
vdoSGAdiAbortReq
long
tmnxVdoSGAdiAbortReq
The value of tmnxVdoSGAdiAbortReq
indicates the total number of abort
requests received from the Ad Insert (ADI)
server.
(15 of 28)
E-138
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoSGAdiAliveReq
long
tmnxVdoSGAdiAliveReq
The value of tmnxVdoSGAdiAliveReq
indicates the total number of alive
messages received from the Ad Insert
(ADI) server.
vdoSGAdiCueReq
long
tmnxVdoSGAdiCueReq
The value of tmnxVdoSGAdiCueReq
indicates the total number of total
number of cue requests sent to the Ad
Insert (ADI) server.
vdoSGAdiInitReq
long
tmnxVdoSGAdiInitReq
The value of tmnxVdoSGAdiInitReq
indicates the total number of init requests
received from the Ad Insert (ADI) server.
vdoSGAdiServerAddr
String
tmnxVdoSGAdiServerAddr
The value of tmnxVdoSGAdiServerAddr
indicates the address of Ad Insert (ADI)
server on this channel.
vdoSGAdiServerAddrType
int
tmnxVdoSGAdiServerAddr
Type
The value of
tmnxVdoSGAdiServerAddrType indicates
the type of Ad Insert (ADI) server address
represented by
tmnxVdoSGAdiServerAddr.
vdoSGAdiServerUptime
long
tmnxVdoSGAdiServerUpti
me
The value of tmnxVdoSGAdiServerUptime
indicates the time in seconds since the
connection with Ad Insert (ADI) server was
established.
vdoSGAdiSpliceReq
long
tmnxVdoSGAdiSpliceReq
The value of tmnxVdoSGAdiSpliceReq
indicates the total number of splice
requests received from the Ad Insert (ADI)
server.
vdoSGAdiSucAbortResp
long
tmnxVdoSGAdiSucAbortR
esp
The value of tmnxVdoSGAdiSucAbortResp
indicates the total number of successful
abort responses sent to the Ad Insert (ADI)
server.
vdoSGAdiSucAliveResp
long
tmnxVdoSGAdiSucAliveRe
sp
The value of tmnxVdoSGAdiSucAliveResp
indicates the total number of successful
alive messages sent to the Ad Insert (ADI)
server.
vdoSGAdiSucCueResp
long
tmnxVdoSGAdiSucCueRes
p
The value of tmnxVdoSGAdiSucCueResp
indicates the total number of successful
cue responses received from the Ad Insert
(ADI) server.
vdoSGAdiSucInitResp
long
tmnxVdoSGAdiSucInitRes
p
The value of tmnxVdoSGAdiSucInitResp
indicates the total number of successful
init responses sent to the Ad Insert (ADI)
server.
vdoSGAdiSucSpliceInCompResp
long
tmnxVdoSGAdiSucSpliceIn
CompResp
The value of
tmnxVdoSGAdiSucSpliceInCompResp
indicates the total number of successful
splice-in complete responses sent to the
Ad Insert (ADI) server.
vdoSGAdiSucSpliceOutCompResp
long
tmnxVdoSGAdiSucSpliceO
utCompResp
The value of
tmnxVdoSGAdiSucSpliceOutCompResp
indicates the total number of successful
splice-out complete responses sent to the
Ad Insert (ADI) server.
(16 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-139
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoSGAdiSucSpliceResp
long
tmnxVdoSGAdiSucSpliceR
esp
The value of tmnxVdoSGAdiSucSpliceResp
indicates the total number of successful
splice responses sent to the Ad Insert
(ADI) server.
vdoSGAdiUnknownSCTE30Req
long
tmnxVdoSGAdiUnknownS
CTE30Req
The value of
tmnxVdoSGAdiUnknownSCTE30Req
indicates the total number of invalid
Society of Cable Telecommunications
Engineers 30 (SCTE-30) requests received
from the Ad Insert (ADI) server.
vdoSGAdiUnsucAbortResp
long
tmnxVdoSGAdiUnsucAbor
tResp
The value of
tmnxVdoSGAdiUnsucAbortResp indicates
the total number of unsuccessful abort
responses sent to the Ad Insert (ADI)
server.
vdoSGAdiUnSucAliveResp
long
tmnxVdoSGAdiUnSucAlive
Resp
The value of
tmnxVdoSGAdiUnSucAliveResp indicates
the total number of unsuccessful alive
messages sent to the Ad Insert (ADI)
server.
vdoSGAdiUnsucCueResp
long
tmnxVdoSGAdiUnsucCueR
esp
The value of tmnxVdoSGAdiUnsucCueResp
indicates the total number of
unsuccessful cue responses received from
the Ad Insert (ADI) server.
vdoSGAdiUnsucInitResp
long
tmnxVdoSGAdiUnsucInitR
esp
The value of tmnxVdoSGAdiUnsucInitResp
indicates the total number of
unsuccessful init responses sent to the Ad
Insert (ADI) server.
vdoSGAdiUnsucSpliceOutComRes
long
tmnxVdoSGAdiUnsucSplic
eOutComRes
The value of
tmnxVdoSGAdiUnsucSpliceOutComRes
indicates the total number of
unsuccessful splice-out complete
responses sent to the Ad Insert (ADI)
server.
vdoSGAdiUnsucSpliceResp
long
tmnxVdoSGAdiUnsucSplic
eResp
The value of
tmnxVdoSGAdiUnsucSpliceResp indicates
the total number of unsuccessful splice
responses sent to the Ad Insert (ADI)
server.
VdoGrpSrcSpliceStats
MIB table name: TIMETRA-VIDEO-MIB.tmnxVdoSGSpliceStatusTable
Monitored class: service.ZoneAdiChl
vdoSGSpliceAbortReason
long
tmnxVdoSGSpliceAbortRe
ason
The value of
tmnxVdoSGSpliceAbortReason indicates
the reason if a splice operation has been
aborted. If the value of this object is
equal to 'none', then the splice has not
been aborted.
vdoSGSpliceAdServerAddr
String
tmnxVdoSGSpliceAdServe
rAddr
The value of
tmnxVdoSGSpliceAdServerAddr indicates
the address of the Ad Insert (ADI) server
that issued the splice request.
(17 of 28)
E-140
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoSGSpliceAdServerAddrType
int
tmnxVdoSGSpliceAdServe
rAddrType
The value of
tmnxVdoSGSpliceAdServerAddrType
indicates the type of Ad Insert (ADI)
server address represented by
tmnxVdoSGSpliceAdServerAddr.
vdoSGSpliceBlkFramePTS
String
tmnxVdoSGSpliceBlkFram
ePTS
The value of
tmnxVdoSGSpliceBlkFramePTS indicates
the Presentation Timestamp (PTS) of the
first black frame.
vdoSGSpliceDurationPlayed
long
tmnxVdoSGSpliceDuratio
nPlayed
The value of
tmnxVdoSGSpliceDurationPlayed
indicates the splice duration, in seconds,
played by the splicer.
vdoSGSpliceDurationReq
long
tmnxVdoSGSpliceDuratio
nReq
The value of
tmnxVdoSGSpliceDurationReq indicates
the splice duration, in seconds, of the ad
requested by the Ad Insert (ADI) server.
vdoSGSpliceMaxAdPTS
String
tmnxVdoSGSpliceMaxAdP
TS
The value of tmnxVdoSGSpliceMaxAdPTS
indicates the maximum Presentation
Timestamp (PTS) value of the last Group
of Pictures (GOP) of ad stream (non-black
frame).
vdoSGSpliceMinNwPTS
String
tmnxVdoSGSpliceMinNwP
TS
The value of tmnxVdoSGSpliceMinNwPTS
indicates the minimum Presentation
Timestamp (PTS) value from the first
Group of Pictures (GOP) of the network
stream after the splice out has occured.
vdoSGSpliceNumBlkFrames
long
tmnxVdoSGSpliceNumBlk
Frames
The value of
tmnxVdoSGSpliceNumBlkFrames indicates
the number of black frames inserted.
vdoSGSplicePriorSessionId
long
tmnxVdoSGSplicePriorSes
sionId
The value of
tmnxVdoSGSplicePriorSessionId indicates
the prior session id of the ad. If the value
of this object is not equal to 0xFFFFFFFF,
then this splice is a back-to-back ad
insertion.
vdoSGSpliceRate
long
tmnxVdoSGSpliceRate
The value of tmnxVdoSGSpliceRate
indicates the rate of the ad stream, in
kilo-bits per second (kbps), received by
the splicer.
vdoSGSpliceSessionId
long
tmnxVdoSGSpliceSessionI
d
The value of tmnxVdoSGSpliceSessionId
indicates the session ID of the ad request.
vdoSGSpliceSpliceInSeqNum
long
tmnxVdoSGSpliceSpliceIn
SeqNum
The value of
tmnxVdoSGSpliceSpliceInSeqNum
indicates the sequence number at which
the splice-in to the ad occurred.
vdoSGSpliceSpliceOutSeqNum
long
tmnxVdoSGSpliceSpliceO
utSeqNum
The value of
tmnxVdoSGSpliceSpliceOutSeqNum
indicates the sequence number at which
the splice-out to the ad occurred.
vdoSGSpliceStartTime
long
tmnxVdoSGSpliceStartTi
me
The value of tmnxVdoSGSpliceStartTime
indicates the start time of splice in
seconds.
vdoSGSpliceStatus
long
tmnxVdoSGSpliceStatus
The value of tmnxVdoSGSpliceStatus
indicates the status of this splice request.
(18 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-141
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
VdoGrpSrcStats
MIB table name: TIMETRA-VIDEO-MIB.tmnxVdoGrpSrcStatTable
Monitored classes:
•
•
service.AdiChl
service.ZoneAdiChl
vdoGrpSrcADIAdminState
int
tmnxVdoGrpSrcADIAdmin
State
The value of
tmnxVdoGrpSrcADIAdminState indicates
whether Ad Insertion is enabled on the
video ISA.
vdoGrpSrcADICurrentState
long
tmnxVdoGrpSrcADICurren
tState
The value of
tmnxVdoGrpSrcADICurrentState indicates
whether the video ISA is transmitting
network stream or ads.
vdoGrpSrcADIPATChanges
long
tmnxVdoGrpSrcADIPATCh
anges
The value of
tmnxVdoGrpSrcADIPATChanges indicates
the total number of Program Association
Table (PAT) version changes.
vdoGrpSrcADIPATVersion
long
tmnxVdoGrpSrcADIPATVe
rsion
The value of
tmnxVdoGrpSrcADIPATVersion indicates
the version of the Program Association
Table (PAT).
vdoGrpSrcADIPMTChanges
long
tmnxVdoGrpSrcADIPMTCh
anges
The value of
tmnxVdoGrpSrcADIPMTChanges indicates
the total number of Program Map Table
(PMT) version changes.
vdoGrpSrcADIPMTVersion
long
tmnxVdoGrpSrcADIPMTVe
rsion
The value of
tmnxVdoGrpSrcADIPMTVersion indicates
the version of the Program Map Table
(PMT).
vdoGrpSrcADIRxPackets
UINT128
tmnxVdoGrpSrcADIRxPac
kets
The value of tmnxVdoGrpSrcADIRxPackets
indicates the total number of Ad Insert
(ADI) packets received by the video ISA.
vdoGrpSrcADIRxSCTE35MsgDisc
long
tmnxVdoGrpSrcADIRxSCT
E35MsgDisc
The value of
tmnxVdoGrpSrcADIRxSCTE35MsgDisc
indicates the total number of Society of
Cable Telecommunications Engineers
(SCTE-35) messages received by the video
ISA and discarded. SCTE-35 messages with
unsupported commands and encrypted
SCTE-35 messages are discarded.
vdoGrpSrcADIRxSCTE35MsgEnc
long
tmnxVdoGrpSrcADIRxSCT
E35MsgEnc
The value of
tmnxVdoGrpSrcADIRxSCTE35MsgEnc
indicates the total number of encrypted
Society of Cable Telecommunications
Engineers (SCTE-35) messages received by
the video ISA.
vdoGrpSrcADIRxSCTE35Msgs
long
tmnxVdoGrpSrcADIRxSCT
E35Msgs
The value of
tmnxVdoGrpSrcADIRxSCTE35Msgs
indicates the total number of Society of
Cable Telecommunications Engineers
(SCTE-35) messages received by the video
ISA.
(19 of 28)
E-142
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpSrcADIRxSCTE35MsgUnsup
long
tmnxVdoGrpSrcADIRxSCT
E35MsgUnsup
The value of
tmnxVdoGrpSrcADIRxSCTE35MsgUnsup
indicates the total number of
unsupported Society of Cable
Telecommunications Engineers (SCTE-35)
messages received by the video ISA.
vdoGrpSrcADITxPackets
UINT128
tmnxVdoGrpSrcADITxPac
kets
The value of tmnxVdoGrpSrcADITxPackets
indicates the total number of Ad Insert
(ADI) packets sent by the video ISA.
vdoGrpSrcADIUnsuppTSLenPkts
long
tmnxVdoGrpSrcADIUnsup
pTSLenPkts
The value of
tmnxVdoGrpSrcADIUnsuppTSLenPkts
indicates the total number of data
packets received whose size is not equal
to 188 bytes. The value of this object is
valid only when the corresponding
tmnxVdoGrpADIServerState value is set to
'true'.
vdoGrpSrcAdminBW
long
tmnxVdoGrpSrcAdminBW
The value of tmnxVdoGrpSrcAdminBW
indicates the administrative bandwidth of
the multicast group.
vdoGrpSrcAdminRTBufferSize
long
tmnxVdoGrpSrcAdminRTB
ufferSize
The value of
tmnxVdoGrpSrcAdminRTBufferSize
indicates the number of milliseconds
worth of channel packets to store for the
Retransmission (RT) server.
vdoGrpSrcBufferSize
long
tmnxVdoGrpSrcBufferSize
The value of tmnxVdoGrpSrcBufferSize
indicates the number of milliseconds
worth of channel packets stored by the
Retransmission (RT) server or Fast
Channel Change (FCC) server on this
channel.
vdoGrpSrcDupSeqNumber
long
tmnxVdoGrpSrcDupSeqNu
mber
The value of
tmnxVdoGrpSrcDupSeqNumber indicates
the total number of Real-time Transport
Protocol (RTP) packets detected with a
duplicate sequence number.
vdoGrpSrcFCCSrvrAdminState
int
tmnxVdoGrpSrcFCCSrvrA
dminState
The value of
tmnxVdoGrpSrcFCCSrvrAdminState
indicates whether the Fast Channel
Change (FCC) server is enabled on this
channel.
vdoGrpSrcFCCSrvrChnlType
int
tmnxVdoGrpSrcFCCSrvrCh
nlType
The value of
tmnxVdoGrpSrcFCCSrvrChnlType
indicates the type of channel served by
the Fast Channel Change (FCC) server.
vdoGrpSrcFCCSrvrRxFailedReq
long
tmnxVdoGrpSrcFCCSrvrRx
FailedReq
The value of
tmnxVdoGrpSrcFCCSrvrRxFailedReq
indicates the total number of failed
requests at the Fast Channel Change
(FCC) server.
vdoGrpSrcFCCSrvrRxFCCReq
long
tmnxVdoGrpSrcFCCSrvrRx
FCCReq
The value of
tmnxVdoGrpSrcFCCSrvrRxFCCReq
indicates the total number of Fast
Channel Change (FCC) requests received
by the FCC server.
(20 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-143
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpSrcFCCSrvrTxBytes
UINT128
tmnxVdoGrpSrcFCCSrvrTx
Bytes
The value of
tmnxVdoGrpSrcFCCSrvrTxBytes indicates
the total number of bytes sent by the Fast
Channel Change (FCC) server.
vdoGrpSrcFCCSrvrTxFCCReplies
long
tmnxVdoGrpSrcFCCSrvrTx
FCCReplies
The value of
tmnxVdoGrpSrcFCCSrvrTxFCCReplies
indicates the total number of Fast
Channel Change (FCC) replies sent by the
FCC server.
vdoGrpSrcFCCSrvrTxPackets
UINT128
tmnxVdoGrpSrcFCCSrvrTx
Packets
The value of
tmnxVdoGrpSrcFCCSrvrTxPackets
indicates the total number of packets sent
by the Fast Channel Change (FCC) server.
vdoGrpSrcGroupAddress
String
tmnxVdoGrpSrcGroupAdd
ress
The value of
tmnxVdoGrpSrcGroupAddress indicates
the IP multicast group address for which
this entry contains information.
vdoGrpSrcGrpAddrType
int
tmnxVdoGrpSrcGrpAddrT
ype
The value of tmnxVdoGrpSrcGrpAddrType
indicates the type of IP multicast group
address represented by
tmnxVdoGrpSrcGroupAddress.
vdoGrpSrcRTClientAdminState
int
tmnxVdoGrpSrcRTClientA
dminState
The value of
tmnxVdoGrpSrcRTClientAdminState
indicates the administrative state of the
retransmission client.
vdoGrpSrcRTClientFailedReq
long
tmnxVdoGrpSrcRTClientF
ailedReq
The value of
tmnxVdoGrpSrcRTClientFailedReq
indicates the total number of
Retransmission (RT) requests that could
not be generated by the RT client due to
gaps in the sequence numbers.
vdoGrpSrcRTClientGapsDetectd
long
tmnxVdoGrpSrcRTClientG
apsDetectd
The value of
tmnxVdoGrpSrcRTClientGapsDetectd
indicates the total number of gaps in the
sequence numbers detected by the
Retransmission (RT) client.
vdoGrpSrcRTClientRTSrvrPort
long
tmnxVdoGrpSrcRTClientR
TSrvrPort
The value of
tmnxVdoGrpSrcRTClientRTSrvrPort
indicates the Retransmission (RT) server
port for this channel.
vdoGrpSrcRTClientRxReTxBytes
UINT128
tmnxVdoGrpSrcRTClientR
xReTxBytes
The value of
tmnxVdoGrpSrcRTClientRxReTxBytes
indicates the total number of
retransmitted bytes received by the
Retransmission (RT) client.
vdoGrpSrcRTClientRxReTxPkts
UINT128
tmnxVdoGrpSrcRTClientR
xReTxPkts
The value of
tmnxVdoGrpSrcRTClientRxReTxPkts
indicates the total number of
retransmitted packets received by the
Retransmission (RT) client.
vdoGrpSrcRTClientTxRTReq
long
tmnxVdoGrpSrcRTClientT
xRTReq
The value of
tmnxVdoGrpSrcRTClientTxRTReq
indicates the total number of
Retransmission (RT) requests sent by the
RT client.
(21 of 28)
E-144
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpSrcRTClientTxRTReqReTx
long
tmnxVdoGrpSrcRTClientT
xRTReqReTx
The value of
tmnxVdoGrpSrcRTClientTxRTReqReTx
indicates the total number of repeat
Retransmission (RT) requests attempted
by the RT client.
vdoGrpSrcRTClntRTSvrAddr
String
tmnxVdoGrpSrcRTClntRT
SvrAddr
The value of
tmnxVdoGrpSrcRTClntRTSvrAddr
indicates the address of the
Retransmission (RT) server for this
channel.
vdoGrpSrcRTClntRTSvrAddrType
int
tmnxVdoGrpSrcRTClntRT
SvrAddrType
The value of
tmnxVdoGrpSrcRTClntRTSvrAddrType
indicates the type of address represented
by tmnxVdoGrpSrcRTClntRTSvrAddr.
vdoGrpSrcRTSrvrAdminState
int
tmnxVdoGrpSrcRTSrvrAd
minState
The value of
tmnxVdoGrpSrcRTSrvrAdminState
indicates the administrative state of the
Retransmission (RT) server.
vdoGrpSrcRTSrvrRtpPktsReq
long
tmnxVdoGrpSrcRTSrvrRtp
PktsReq
The value of
tmnxVdoGrpSrcRTSrvrRtpPktsReq
indicates the totoal number of Real-time
Transport Protocol (RTP) packets
requested in the Real-time Transport
Control Protocol (RTCP) feedback (FB)
messages received on this channel.
vdoGrpSrcRTSrvrRxFailedReq
long
tmnxVdoGrpSrcRTSrvrRxF
ailedReq
The value of
tmnxVdoGrpSrcRTSrvrRxFailedReq
indicates the total number of failed
requests at the Retransmission (RT) server
due to congestion or lack of resources.
vdoGrpSrcRTSrvrRxRTReq
long
tmnxVdoGrpSrcRTSrvrRxR
TReq
The value of
tmnxVdoGrpSrcRTSrvrRxRTReq indicates
the total number of RT requests received
by the Retransmission (RT) server.
vdoGrpSrcRTSrvrTxBytes
UINT128
tmnxVdoGrpSrcRTSrvrTxB
ytes
The value of
tmnxVdoGrpSrcRTSrvrTxBytes indicates
the total number of bytes sent by the
Retransmission (RT) server.
vdoGrpSrcRTSrvrTxPackets
UINT128
tmnxVdoGrpSrcRTSrvrTxP
ackets
The value of
tmnxVdoGrpSrcRTSrvrTxPackets indicates
the total number of packets sent by the
Retransmission (RT) server.
vdoGrpSrcRTSrvrTxRTReplies
long
tmnxVdoGrpSrcRTSrvrTxR
TReplies
The value of
tmnxVdoGrpSrcRTSrvrTxRTReplies
indicates the total number of
Retransmission (RT) replies sent by the RT
server.
vdoGrpSrcRxBytes
UINT128
tmnxVdoGrpSrcRxBytes
The value of tmnxVdoGrpSrcRxBytes
indicates the total number of bytes
received on this multicast channel.
vdoGrpSrcRxInvalidPackets
UINT128
tmnxVdoGrpSrcRxInvalid
Packets
The value of
tmnxVdoGrpSrcRxInvalidPackets
indicates the total number of invalid
packets received on this multicast
channel.
(22 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-145
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoGrpSrcRxPackets
UINT128
tmnxVdoGrpSrcRxPackets
The value of tmnxVdoGrpSrcRxPackets
indicates the total number of packets
received on this multicast channel.
vdoGrpSrcSourceAddress
String
tmnxVdoGrpSrcSourceAd
dress
The value of
tmnxVdoGrpSrcSourceAddress indicates
the IP multicast source address for which
this entry contains information.
vdoGrpSrcSrcAddrType
int
tmnxVdoGrpSrcSrcAddrTy
pe
The value of tmnxVdoGrpSrcSrcAddrType
indicates the type of IP multicast source
address represented by
tmnxVdoGrpSrcSourceAddress.
vdoGrpSrcSSRCId
long
tmnxVdoGrpSrcSSRCId
The value of tmnxVdoGrpSrcSSRCId
indicates the synchronization source
(SSRC) identifier carried in the Real-time
Transport Protocol (RTP) header to
identify the source of a stream of RTP
packets.
vdoGrpSrcStreamType
long
tmnxVdoGrpSrcStreamTy
pe
The value of tmnxVdoGrpSrcStreamType
indicates the type of stream being
transmitted from the video ISA
perspective. Network stream is the
stream ingressing the video ISA and being
stored by it. Zone stream is the stream
egressing the video ISA into which AD
streams will be inserted.
vdoGrpSrcTxBytes
UINT128
tmnxVdoGrpSrcTxBytes
The value of tmnxVdoGrpSrcTxBytes
indicates the total number of bytes
transmitted on this multicast channel.
vdoGrpSrcTxFailedPackets
UINT128
tmnxVdoGrpSrcTxFailedP
ackets
The value of
tmnxVdoGrpSrcTxFailedPackets indicates
the total number of failures during the
transmission of packets on this multicast
channel. Failure happens when the
packet to be sent is not stored in the
video cache.
vdoGrpSrcTxPackets
UINT128
tmnxVdoGrpSrcTxPackets
The value of tmnxVdoGrpSrcTxPackets
indicates the total number of packets
transmitted on this multicast channel.
vdoGrpSrcUDPDestPort
long
tmnxVdoGrpSrcUDPDestP
ort
The value of tmnxVdoGrpSrcUDPDestPort
indicates the UDP destination port in the
received RTP multicast stream.
vdoGrpSrcUDPSrcPort
long
tmnxVdoGrpSrcUDPSrcPo
rt
The value of tmnxVdoGrpSrcUDPSrcPort
indicates the UDP source port in the
received RTP multicast stream.
vdoGrpSrcUptime
long
tmnxVdoGrpSrcUptime
The value of tmnxVdoGrpSrcUptime
indicates the time since this source group
entry was created.
vdoGrpSrcVdoGrpId
long
tmnxVdoGrpSrcVdoGrpId
The value of tmnxVdoGrpSrcVdoGrpId
indicates the identifier of the video
group.
VdoIfStats
MIB table name: TIMETRA-VIDEO-MIB.tmnxVdoIfStatTable
Monitored class: service.VideoIfIpAddress
(23 of 28)
E-146
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoIfScte30InitSessions
long
tmnxVdoIfScte30InitSessi
ons
The value of tmnxVdoIfScte30InitSessions
indicates the total number of scte30 init
sessions with the Ad Insert (ADI) servers
for this interface.
vdoIfScte30TcpSessions
long
tmnxVdoIfScte30TcpSessi
ons
The value of tmnxVdoIfScte30TcpSessions
indicates the total number of scte30 tcp
sessions with the Ad Insert (ADI) servers
for this interface.
vdoIfStatFCCSrRxHdFailedReq
UINT128
tmnxVdoIfStatFCCSrRxHd
FailedReq
The value of
tmnxVdoIfStatFCCSrRxHdFailedReq
indicates the total number of failed Fast
Channel Change (FCC) requests received
from High Definition (HD) channels on this
interface.
vdoIfStatFCCSrRxHdFCCReq
UINT128
tmnxVdoIfStatFCCSrRxHd
FCCReq
The value of
tmnxVdoIfStatFCCSrRxHdFCCReq
indicates the total number of Fast
Channel Change (FCC) requests received
from High Definition (HD) channels on this
interface.
vdoIfStatFCCSrRxPipFailedReq
UINT128
tmnxVdoIfStatFCCSrRxPip
FailedReq
The value of
tmnxVdoIfStatFCCSrRxPipFailedReq
indicates the total number of failed Fast
Channel Change (FCC) requests received
from Picture-In-Picture (PIP) channels on
this interface.
vdoIfStatFCCSrRxPipFCCReq
UINT128
tmnxVdoIfStatFCCSrRxPip
FCCReq
The value of
tmnxVdoIfStatFCCSrRxPipFCCReq
indicates the total number of Fast
Channel Change (FCC) requests received
from Picture-In-Picture (PIP) channels on
this interface.
vdoIfStatFCCSrRxSdFailedReq
UINT128
tmnxVdoIfStatFCCSrRxSd
FailedReq
The value of
tmnxVdoIfStatFCCSrRxSdFailedReq
indicates the total number of failed Fast
Channel Change (FCC) requests received
from Standard Definition (SD) channels on
this interface.
vdoIfStatFCCSrRxSdFCCReq
UINT128
tmnxVdoIfStatFCCSrRxSd
FCCReq
The value of
tmnxVdoIfStatFCCSrRxSdFCCReq
indicates the total number of Fast
Channel Change (FCC) requests received
from Standard Definition (SD) channels on
this interface.
vdoIfStatFCCSrTxHdBytes
UINT128
tmnxVdoIfStatFCCSrTxHd
Bytes
The value of
tmnxVdoIfStatFCCSrTxHdBytes indicates
the total number of High Definition (HD)
channel bytes sent from this interface.
vdoIfStatFCCSrTxHdFCCReplies
UINT128
tmnxVdoIfStatFCCSrTxHd
FCCReplies
The value of
tmnxVdoIfStatFCCSrTxHdFCCReplies
indicates the total number of High
Definition (HD) channel Fast Channel
Change (FCC) replies sent from this
interface.
(24 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-147
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoIfStatFCCSrTxHdPackets
UINT128
tmnxVdoIfStatFCCSrTxHd
Packets
The value of
tmnxVdoIfStatFCCSrTxHdPackets
indicates the total number of High
Definition (HD) channel packets sent from
this interface.
vdoIfStatFCCSrTxPipBytes
UINT128
tmnxVdoIfStatFCCSrTxPip
Bytes
The value of
tmnxVdoIfStatFCCSrTxPipBytes indicates
the total number of Picture-In-Picture
(PIP) channel bytes sent from this
interface.
vdoIfStatFCCSrTxPipFCCRplies
UINT128
tmnxVdoIfStatFCCSrTxPip
FCCRplies
The value of
tmnxVdoIfStatFCCSrTxPipFCCRplies
indicates the total number of
Picture-In-Picture (PIP) channel Fast
Channel Change (FCC) replies sent from
this interface.
vdoIfStatFCCSrTxPipPackets
UINT128
tmnxVdoIfStatFCCSrTxPip
Packets
The value of
tmnxVdoIfStatFCCSrTxPipPackets
indicates the total number of
Picture-In-Picture (PIP) channel packets
sent from this interface.
vdoIfStatFCCSrTxSdBytes
UINT128
tmnxVdoIfStatFCCSrTxSd
Bytes
The value of
tmnxVdoIfStatFCCSrTxSdBytes indicates
the total number of Standard Definition
(SD) channel bytes sent from this
interface.
vdoIfStatFCCSrTxSdFCCReplies
UINT128
tmnxVdoIfStatFCCSrTxSd
FCCReplies
The value of
tmnxVdoIfStatFCCSrTxSdFCCReplies
indicates the total number of Standard
Definition (SD) channel Fast Channel
Change (FCC) replies sent from this
interface.
vdoIfStatFCCSrTxSdPackets
UINT128
tmnxVdoIfStatFCCSrTxSd
Packets
The value of
tmnxVdoIfStatFCCSrTxSdPackets
indicates the total number of Standard
Definition (SD) channel packets sent from
this interface.
vdoIfStatHdFCCServerMode
int
tmnxVdoIfStatHdFCCServ
erMode
The value of
tmnxVdoIfStatHdFCCServerMode
indicates the mode of the High Definition
(HD) Fast Channel Change (FCC) server on
this interface.
vdoIfStatHdRTServerState
boolean
tmnxVdoIfStatHdRTServe
rState
The value of
tmnxVdoIfStatHdRTServerState indicates
whether the High Definition (HD)
retransmission server is enabled on this
interface.
vdoIfStatPipFCCServerMode
int
tmnxVdoIfStatPipFCCServ
erMode
The value of
tmnxVdoIfStatPipFCCServerMode
indicates the mode of the
Picture-in-Picture (PIP) Fast Channel
Change (FCC) server on this interface.
vdoIfStatPipRTServerState
boolean
tmnxVdoIfStatPipRTServe
rState
The value of
tmnxVdoIfStatPipRTServerState indicates
whether the Picture-in-Picture (PIP)
retransmission server is enabled on this
interface.
(25 of 28)
E-148
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoIfStatRTSvrHdRtpPktsReq
UINT128
tmnxVdoIfStatRTSvrHdRt
pPktsReq
The value of
tmnxVdoIfStatRTSvrHdRtpPktsReq
indicates the total number of High
Definition (HD) channel Real-time
Transport Protocol (RTP) packets
requested in the Real-time Transport
Control Protocol (RTCP) feedback (FB)
messages received on this interface.
vdoIfStatRTSvrPipRtpPktsReq
UINT128
tmnxVdoIfStatRTSvrPipRt
pPktsReq
The value of
tmnxVdoIfStatRTSvrPipRtpPktsReq
indicates the total number of
Picture-In-Picture (PIP) channel Real-time
Transport Protocol (RTP) packets
requested in the Real-time Transport
Control Protocol (RTCP) feedback (FB)
messages received on this interface.
vdoIfStatRTSvrRxHdFailedReq
UINT128
tmnxVdoIfStatRTSvrRxHd
FailedReq
The value of
tmnxVdoIfStatRTSvrRxHdFailedReq
indicates the total number of failed
Retransmission (RT) requests received
from High Definition (HD) channels on this
interface.
vdoIfStatRTSvrRxHdRTReq
UINT128
tmnxVdoIfStatRTSvrRxHd
RTReq
The value of
tmnxVdoIfStatRTSvrRxHdRTReq indicates
the total number of Retransmission (RT)
requests received from High Definition
(HD) channels on this interface.
vdoIfStatRTSvrRxPipFailedReq
UINT128
tmnxVdoIfStatRTSvrRxPip
FailedReq
The value of
tmnxVdoIfStatRTSvrRxPipFailedReq
indicates the total number of failed
Retransmission (RT) requests received
from Picture-In-Picture (PIP) channels on
this interface.
vdoIfStatRTSvrRxPipRTReq
UINT128
tmnxVdoIfStatRTSvrRxPip
RTReq
The value of
tmnxVdoIfStatRTSvrRxPipRTReq indicates
the total number of Retransmission (RT)
requests received from Picture-In-Picture
(PIP) channels on this interface.
vdoIfStatRTSvrRxSdFailedReq
UINT128
tmnxVdoIfStatRTSvrRxSd
FailedReq
The value of
tmnxVdoIfStatRTSvrRxSdFailedReq
indicates the total number of failed
Retransmission (RT) requests received
from Standard Definition (SD) channels on
this interface.
vdoIfStatRTSvrRxSdRTReq
UINT128
tmnxVdoIfStatRTSvrRxSd
RTReq
The value of
tmnxVdoIfStatRTSvrRxSdRTReq indicates
the total number of Retransmission (RT)
requests received from Standard
Definition (SD) channels on this interface.
vdoIfStatRTSvrSdRtpPktsReq
UINT128
tmnxVdoIfStatRTSvrSdRtp
PktsReq
The value of
tmnxVdoIfStatRTSvrSdRtpPktsReq
indicates the total number of Standard
Definition (SD) channel Real-time
Transport Protocol (RTP) packets
requested in the Real-time Transport
Control Protocol (RTCP) feedback (FB)
messages received on this interface.
(26 of 28)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-149
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoIfStatRTSvrTxHdBytes
UINT128
tmnxVdoIfStatRTSvrTxHd
Bytes
The value of
tmnxVdoIfStatRTSvrTxHdBytes indicates
the total number of High Definition (HD)
channel bytes sent from this interface.
vdoIfStatRTSvrTxHdPackets
UINT128
tmnxVdoIfStatRTSvrTxHd
Packets
The value of
tmnxVdoIfStatRTSvrTxHdPackets
indicates the total number of High
Definition (HD) channel packets sent from
this interface.
vdoIfStatRTSvrTxHdRTReplies
UINT128
tmnxVdoIfStatRTSvrTxHd
RTReplies
The value of
tmnxVdoIfStatRTSvrTxHdRTReplies
indicates the total number of High
Definition (HD) channel Retransmission
(RT) replies sent from this interface.
vdoIfStatRTSvrTxPipBytes
UINT128
tmnxVdoIfStatRTSvrTxPip
Bytes
The value of
tmnxVdoIfStatRTSvrTxPipBytes indicates
the total number of Picture-In-Picture
(PIP) channel bytes sent from this
interface.
vdoIfStatRTSvrTxPipPackets
UINT128
tmnxVdoIfStatRTSvrTxPip
Packets
The value of
tmnxVdoIfStatRTSvrTxPipPackets
indicates the total number of
Picture-In-Picture (PIP) channel packets
sent from this interface.
vdoIfStatRTSvrTxPipRTReplies
UINT128
tmnxVdoIfStatRTSvrTxPip
RTReplies
The value of
tmnxVdoIfStatRTSvrTxPipRTReplies
indicates the total number of
Picture-In-Picture (PIP) channel
Retransmission (RT) replies sent from this
interface.
vdoIfStatRTSvrTxSdBytes
UINT128
tmnxVdoIfStatRTSvrTxSd
Bytes
The value of
tmnxVdoIfStatRTSvrTxSdBytes indicates
the total number of Standard Definition
(SD) channel bytes sent from this
interface.
vdoIfStatRTSvrTxSdPackets
UINT128
tmnxVdoIfStatRTSvrTxSd
Packets
The value of
tmnxVdoIfStatRTSvrTxSdPackets
indicates the total number of Standard
Definition (SD) channel packets sent from
this interface.
vdoIfStatRTSvrTxSdRTReplies
UINT128
tmnxVdoIfStatRTSvrTxSd
RTReplies
The value of
tmnxVdoIfStatRTSvrTxSdRTReplies
indicates the total number of Standard
Definition (SD) channel Retransmission
(RT) replies sent from this interface.
vdoIfStatSdFCCServerMode
int
tmnxVdoIfStatSdFCCServ
erMode
The value of
tmnxVdoIfStatSdFCCServerMode indicates
the mode of the Standard Definition (SD)
Fast Channel Change (FCC) server on this
interface.
vdoIfStatSdRTServerState
boolean
tmnxVdoIfStatSdRTServer
State
The value of
tmnxVdoIfStatSdRTServerState indicates
whether the Standard Definition (SD)
retransmission server is enabled on this
interface.
(27 of 28)
E-150
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vdoIfStatTxFailedPackets
UINT128
tmnxVdoIfStatTxFailedPa
ckets
The value of
tmnxVdoIfStatTxFailedPackets indicates
the total number of failures during the
transmission of packets from this video
interface. Failure happens when the
packet to be sent is not stored in the
video cache.
(28 of 28)
Table E-29 sitesec statistics
5620 SAM counter name
Type
MIB counter name
Description
CpmFilterQueueStats
MIB table name: TIMETRA-SECURITY-MIB.tCpmFilterQueueStatsTable
Monitored class: sitesec.CpmFilterQueue
droppedInOctets
UINT128
tCpmFilterQInProfileDrop
Octets
The value of
tCpmFilterQInProfileDropOctets indicates
the number of octets complying to the
queue Qos profile dropped from the
tCpmFilterQueueEntry with the same
index.
droppedInPackets
UINT128
tCpmFilterQInProfileDrop
Pkts
The value of
tCpmFilterQInProfileDropPkts indicates
the number of packets complying to the
queue Qos profile dropped from the
tCpmFilterQueueEntry with the same
index.
droppedOutOctets
UINT128
tCpmFilterQOutProfileDr
opOctets
The value of
tCpmFilterQOutProfileDropOctets
indicates the number of octets not
complying to the queue Qos profile
dropped from the tCpmFilterQueueEntry
with the same index.
droppedOutPackets
UINT128
tCpmFilterQOutProfileDr
opPkts
The value of
tCpmFilterQOutProfileDropPkts indicates
the number of packets not complying to
the queue Qos profile dropped from the
tCpmFilterQueueEntry with the same
index.
forwardedInOctets
UINT128
tCpmFilterQInProfileFwd
Octets
The value of
tCpmFilterQInProfileFwdOctets indicates
the number of octets complying to the
queue Qos profile forwarded from the
tCpmFilterQueueEntry with the same
index.
forwardedInPackets
UINT128
tCpmFilterQInProfileFwd
Pkts
The value of tCpmFilterQInProfileFwdPkts
indicates the number of packets
complying to the queue Qos profile
forwarded from the
tCpmFilterQueueEntry with the same
index.
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-151
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
forwardedOutOctets
UINT128
tCpmFilterQOutProfileFw
dOctets
The value of
tCpmFilterQOutProfileFwdOctets
indicates the number of octets not
complying to the queue Qos profile
forwarded from the
tCpmFilterQueueEntry with the same
index.
forwardedOutPackets
UINT128
tCpmFilterQOutProfileFw
dPkts
The value of
tCpmFilterQOutProfileFwdPkts indicates
the number of packets not complying to
the queue Qos profile forwarded from the
tCpmFilterQueueEntry with the same
index.
CpmIpFilterStats
MIB table name: TIMETRA-SECURITY-MIB.tCpmIpFilterStatsTable
Monitored class: sitesec.CpmIpFilterEntry
droppedPackets
UINT128
tCpmIpFilterStatsDroppe
dPkts
The value of
tCpmIpFilterStatsDroppedPkts indicates
the number of packets dropped due to the
tCpmIpFilterEntry with the same index.
forwardedPackets
UINT128
tCpmIpFilterStatsForward
edPkts
The value of
tCpmIpFilterStatsForwardedPkts
indicates the number of packets
forwarded due to the tCpmIpFilterEntry
with the same index.
CpmMacFilterStats
MIB table name: TIMETRA-SECURITY-MIB.tCpmMacFilterStatsTable
Monitored class: sitesec.CpmMacFilterEntry
droppedPackets
UINT128
tCpmMacFilterStatsDropp
edPkts
The value of
tCpmMacFilterStatsDroppedPkts indicates
the number of packets dropped due to the
tCpmMacFilterEntry with the same index.
forwardedPackets
UINT128
tCpmMacFilterStatsForwa
rdedPkts
The value of
tCpmMacFilterStatsForwardedPkts
indicates the number of packets
forwarded due to the tCpmMacFilterEntry
with the same index.
MafEntryStats
MIB table name: TIMETRA-SECURITY-MIB.tmnxIPMafMatchTable
Monitored class: sitesec.MafEntry
matchCount
UINT128
tmnxIPMafMatchCount
The value of tmnxIPMafMatchCount
indicates the number of times a
management packet has matched this
filter entry.
(2 of 2)
E-152
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
Table E-30 sonetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
SonetFarEndLineCurrentStats
MIB table name: SONET-MIB.sonetFarEndLineCurrentTable
Monitored class: equipment.PhysicalPort
codingViolations
long
sonetFarEndLineCurrentC
Vs
The counter associated with the number
of Far End Coding Violations reported via
the far end block error count encountered
by a SONET/SDH Medium/Section/Line
interface in the current 15 minute
interval.
erroredSeconds
long
sonetFarEndLineCurrentE
Ss
The counter associated with the number
of Far End Errored Seconds encountered
by a SONET/SDH interface in the current
15 minute interval.
severelyErroredSeconds
long
sonetFarEndLineCurrentS
ESs
The counter associated with the number
of Far End Severely Errored Seconds
encountered by a SONET/SDH
Medium/Section/Line interface in the
current 15 minute interval.
unavailableSeconds
long
sonetFarEndLineCurrentU
ASs
The counter associated with the number
of Far End Unavailable Seconds
encountered by a SONET/SDH
Medium/Section/Line interface in the
current 15 minute interval.
SonetFarEndLineIntervalStats
MIB table name: SONET-MIB.sonetFarEndLineIntervalTable
Monitored class: equipment.PhysicalPort
codingViolations
long
sonetFarEndLineIntervalC
Vs
The counter associated with the number
of Far End Coding Violations reported via
the far end block error count encountered
by a SONET/SDH Line interface in a
particular 15-minute interval in the past
24 hours.
erroredSeconds
long
sonetFarEndLineIntervalE
Ss
The counter associated with the number
of Far End Errored Seconds encountered
by a SONET/SDH Line interface in a
particular 15-minute interval in the past
24 hours.
intervalNumber
int
sonetFarEndLineIntervalN
umber
A number between 1 and 96, which
identifies the interval for which the set of
statistics is available. The interval
identified by 1 is the most recently
completed 15 minute interval, and the
interval identified by N is the interval
immediately preceding the one identified
by N-1.
severelyErroredSeconds
long
sonetFarEndLineIntervalS
ESs
The counter associated with the number
of Far End Severely Errored Seconds
encountered by a SONET/SDH Line
interface in a particular 15-minute
interval in the past 24 hours.
(1 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-153
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
unavailableSeconds
long
sonetFarEndLineIntervalU
ASs
The counter associated with the number
of Far End Unavailable Seconds
encountered by a SONET/SDH Line
interface in a particular 15-minute
interval in the past 24 hours.
SonetFarEndPathCurrentStats
MIB table name: SONET-MIB.sonetFarEndPathCurrentTable
Monitored classes:
•
•
•
•
•
•
sonetequipment.Sts1Channel
sonetequipment.Sts3Channel
sonetequipment.Sts12Channel
sonetequipment.Sts48Channel
sonetequipment.Sts192Channel
sonetequipment.Tu3Channel
codingViolations
long
sonetFarEndPathCurrentC
Vs
The counter associated with the number
of Far End Coding Violations reported via
the far end block error count encountered
by a SONET/SDH Path interface in the
current 15 minute interval.
erroredSeconds
long
sonetFarEndPathCurrentE
Ss
The counter associated with the number
of Far End Errored Seconds encountered
by a SONET/SDH interface in the current
15 minute interval.
severelyErroredSeconds
long
sonetFarEndPathCurrentS
ESs
The counter associated with the number
of Far End Severely Errored Seconds
encountered by a SONET/SDH Path
interface in the current 15 minute
interval.
unavailableSeconds
long
sonetFarEndPathCurrent
UASs
The counter associated with the number
of Far End Unavailable Seconds
encountered by a SONET/SDH Path
interface in the current 15 minute
interval.
SonetFarEndPathIntervalStats
MIB table name: SONET-MIB.sonetFarEndPathIntervalTable
Monitored classes:
sonetequipment.Sts1Channel
sonetequipment.Sts3Channel
sonetequipment.Sts12Channel
sonetequipment.Sts48Channel
sonetequipment.Sts192Channel
sonetequipment.Tu3Channel
•
•
•
•
•
•
codingViolations
long
sonetFarEndPathInterval
CVs
The counter associated with the number
of Far End Coding Violations reported via
the far end block error count encountered
by a SONET/SDH Path interface in a
particular 15-minute interval in the past
24 hours.
erroredSeconds
long
sonetFarEndPathIntervalE
Ss
The counter associated with the number
of Far End Errored Seconds encountered
by a SONET/SDH Path interface in a
particular 15-minute interval in the past
24 hours.
(2 of 6)
E-154
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
intervalNumber
int
sonetFarEndPathInterval
Number
A number between 1 and 96, which
identifies the interval for which the set of
statistics is available. The interval
identified by 1 is the most recently
completed 15 minute interval, and the
interval identified by N is the interval
immediately preceding the one identified
by N-1.
severelyErroredSeconds
long
sonetFarEndPathIntervalS
ESs
The counter associated with the number
of Far End Severely Errored Seconds
encountered by a SONET/SDH Path
interface in a particular 15-minute
interval in the past 24 hours.
unavailableSeconds
long
sonetFarEndPathInterval
UASs
The counter associated with the number
of Far End Unavailable Seconds
encountered by a SONET/SDH Path
interface in a particular 15-minute
interval in the past 24 hours.
SonetLineCurrentStats
MIB table name: SONET-MIB.sonetLineCurrentTable
Monitored class: equipment.PhysicalPort
codingViolations
long
sonetLineCurrentCVs
The counter associated with the number
of Coding Violations encountered by a
SONET/SDH Line in the current 15 minute
interval.
currentStatus
long
sonetLineCurrentStatus
This variable indicates the status of the
interface. The sonetLineCurrentStatus is
a bit map represented as a sum,
therefore, it can represent multiple
defects simultaneously. The
sonetLineNoDefect should be set if and
only if no other flag is set. The various bit
positions are: 1 sonetLineNoDefect 2
sonetLineAIS 4 sonetLineRDI.
erroredSeconds
long
sonetLineCurrentESs
The counter associated with the number
of Errored Seconds encountered by a
SONET/SDH Line in the current 15 minute
interval.
severelyErroredSeconds
long
sonetLineCurrentSESs
The counter associated with the number
of Severely Errored Seconds encountered
by a SONET/SDH Line in the current 15
minute interval.
unavailableSeconds
long
sonetLineCurrentUASs
The counter associated with the number
of Unavailable Seconds encountered by a
SONET/SDH Line in the current 15 minute
interval.
SonetLineIntervalStats
MIB table name: SONET-MIB.sonetLineIntervalTable
Monitored class: equipment.PhysicalPort
codingViolations
long
sonetLineIntervalCVs
The counter associated with the number
of Coding Violations encountered by a
SONET/SDH Line in a particular 15-minute
interval in the past 24 hours.
(3 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-155
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
erroredSeconds
long
sonetLineIntervalESs
The counter associated with the number
of Errored Seconds encountered by a
SONET/SDH Line in a particular 15-minute
interval in the past 24 hours.
intervalNumber
int
sonetLineIntervalNumber
A number between 1 and 96, which
identifies the interval for which the set of
statistics is available. The interval
identified by 1 is the most recently
completed 15 minute interval, and the
interval identified by N is the interval
immediately preceding the one identified
by N-1.
severelyErroredSeconds
long
sonetLineIntervalSESs
The counter associated with the number
of Severely Errored Seconds encountered
by a SONET/SDH Line in a particular
15-minute interval in the past 24 hours.
unavailableSeconds
long
sonetLineIntervalUASs
The counter associated with the number
of Unavailable Seconds encountered by a
SONET/SDH Line in a particular 15-minute
interval in the past 24 hours.
SonetPathCurrentStats
MIB table name: SONET-MIB.sonetPathCurrentTable
Monitored classes:
• sonetequipment.Sts1Channel
• sonetequipment.Sts3Channel
• sonetequipment.Sts12Channel
• sonetequipment.Sts48Channel
• sonetequipment.Sts192Channel
• sonetequipment.Tu3Channel
codingViolations
long
sonetPathCurrentCVs
The counter associated with the number
of Coding Violations encountered by a
SONET/SDH Path in the current 15 minute
interval.
currentStatus
long
sonetPathCurrentStatus
This variable indicates the status of the
interface. The sonetPathCurrentStatus is
a bit map represented as a sum,
therefore, it can represent multiple
defects simultaneously. The
sonetPathNoDefect should be set if and
only if no other flag is set. The various bit
positions are: 1 sonetPathNoDefect 2
sonetPathSTSLOP 4 sonetPathSTSAIS 8
sonetPathSTSRDI 16
sonetPathUnequipped 32
sonetPathSignalLabelMismatch.
currentWidth
int
sonetPathCurrentWidth
A value that indicates the type of the
SONET/SDH Path. For SONET, the
assigned types are the STS-Nc SPEs, where
N = 1, 3, 12, 24, 48, 192 and 768. STS-1 is
equal to 51.84 Mbps. For SDH, the
assigned types are the STM-Nc VCs, where
N = 1, 4, 16, 64 and 256.
erroredSeconds
long
sonetPathCurrentESs
The counter associated with the number
of Errored Seconds encountered by a
SONET/SDH Path in the current 15 minute
interval.
(4 of 6)
E-156
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
severelyErroredSeconds
long
sonetPathCurrentSESs
The counter associated with the number
of Severely Errored Seconds encountered
by a SONET/SDH Path in the current 15
minute interval.
unavailableSeconds
long
sonetPathCurrentUASs
The counter associated with the number
of Unavailable Seconds encountered by a
Path in the current 15 minute interval.
SonetPathIntervalStats
MIB table name: SONET-MIB.sonetPathIntervalTable
Monitored classes:
•
•
•
•
•
•
sonetequipment.Sts1Channel
sonetequipment.Sts3Channel
sonetequipment.Sts12Channel
sonetequipment.Sts48Channel
sonetequipment.Sts192Channel
sonetequipment.Tu3Channel
codingViolations
long
sonetPathIntervalCVs
The counter associated with the number
of Coding Violations encountered by a
SONET/SDH Path in a particular 15-minute
interval in the past 24 hours.
erroredSeconds
long
sonetPathIntervalESs
The counter associated with the number
of Errored Seconds encountered by a
SONET/SDH Path in a particular 15-minute
interval in the past 24 hours.
intervalNumber
int
sonetPathIntervalNumber
A number between 1 and 96, which
identifies the interval for which the set of
statistics is available. The interval
identified by 1 is the most recently
completed 15 minute interval, and the
interval identified by N is the interval
immediately preceding the one identified
by N-1.
severelyErroredSeconds
long
sonetPathIntervalSESs
The counter associated with the number
of Severely Errored Seconds encountered
by a SONET/SDH Path in a particular
15-minute interval in the past 24 hours.
unavailableSeconds
long
sonetPathIntervalUASs
The counter associated with the number
of Unavailable Seconds encountered by a
Path in a particular 15-minute interval in
the past 24 hours.
SonetSectionCurrentStats
MIB table name: SONET-MIB.sonetSectionCurrentTable
Monitored class: equipment.PhysicalPort
codingViolations
long
sonetSectionCurrentCVs
The counter associated with the number
of Coding Violations encountered by a
SONET/SDH Section in the current 15
minute interval.
(5 of 6)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-157
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
currentStatus
long
sonetSectionCurrentStatu
s
This variable indicates the status of the
interface. The sonetSectionCurrentStatus
is a bit map represented as a sum,
therefore, it can represent multiple
defects simultaneously. The
sonetSectionNoDefect should be set if and
only if no other flag is set. The various bit
positions are: 1 sonetSectionNoDefect 2
sonetSectionLOS 4 sonetSectionLOF.
erroredSeconds
long
sonetSectionCurrentESs
The counter associated with the number
of Errored Seconds encountered by a
SONET/SDH Section in the current 15
minute interval.
severelyErroredFramingSeconds
long
sonetSectionCurrentSEFSs
The counter associated with the number
of Severely Errored Framing Seconds
encountered by a SONET/SDH Section in
the current 15 minute interval.
severelyErroredSeconds
long
sonetSectionCurrentSESs
The counter associated with the number
of Severely Errored Seconds encountered
by a SONET/SDH Section in the current 15
minute interval.
SonetSectionIntervalStats
MIB table name: SONET-MIB.sonetSectionIntervalTable
Monitored class: equipment.PhysicalPort
codingViolations
long
sonetSectionIntervalCVs
The counter associated with the number
of Coding Violations encountered by a
SONET/SDH Section in a particular
15-minute interval in the past 24 hours.
erroredSeconds
long
sonetSectionIntervalESs
The counter associated with the number
of Errored Seconds encountered by a
SONET/SDH Section in a particular
15-minute interval in the past 24 hours.
intervalNumber
int
sonetSectionIntervalNum
ber
A number between 1 and 96, which
identifies the interval for which the set of
statistics is available. The interval
identified by 1 is the most recently
completed 15 minute interval, and the
interval identified by N is the interval
immediately preceding the one identified
by N-1.
severelyErroredFramingSeconds
long
sonetSectionIntervalSEFS
s
The counter associated with the number
of Severely Errored Framing Seconds
encountered by a SONET/SDH Section in a
particular 15-minute interval in the past
24 hours.
severelyErroredSeconds
long
sonetSectionIntervalSESs
The counter associated with the number
of Severely Errored Seconds encountered
by a SONET/SDH Section in a particular
15-minute interval in the past 24 hours.
(6 of 6)
E-158
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
Table E-31 subscrauth statistics
5620 SAM counter name
Type
MIB counter name
Description
PolicyStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubAuthPlcyStatsTable
Monitored class: subscrauth.Policy
rejectedAuthentications
long
tmnxSubAuthPlcyReject
The value of tmnxSubAuthPlcyReject
indicates how many subscriber messages
(e.g. DHCP, PPPoE, ...) were rejected by
the authentication. Note that not all
requests are therefore forwarded to
radius. If several requests are sent in a
short timeframe, only the first one is sent
to radius.
successfulAuthentications
long
tmnxSubAuthPlcySuccess
The value of tmnxSubAuthPlcySuccess
indicates how many subscriber messages
(e.g. DHCP, PPPoE, ...) were
authenticated successfully. Note that not
all requests are therefore forwarded to
radius. If several requests are sent in a
short timeframe, only the first one is sent
to radius.
RadiusEntryStats
MIB table name: TIMETRA-SUBSCRIBER-MGMT-MIB.tmnxSubAuthPlcyRadStatsTable
Monitored class: subscrauth.RadiusEntry
failedAuthenticationRequests
long
tmnxSubAuthPlcyRadSen
dFail
The value of
tmnxSubAuthPlcyRadSendFail indicates
how many authentication requests failed
because the packet could not be sent out.
md5VerificationFailedRequests
long
tmnxSubAuthPlcyRadMd5
Fail
The value of tmnxSubAuthPlcyRadMd5Fail
indicates how many times the MD5
verification failed on a msg from this
radius server.
pendingAuthenticationRequest
long
tmnxSubAuthPlcyRadPen
ding
The value of tmnxSubAuthPlcyRadPending
indicates how many authentication
requests are currently pending.
rejectedAuthenticationRequests
long
tmnxSubAuthPlcyRadReje
ct
The value of tmnxSubAuthPlcyRadReject
indicates how many authentication
requests were rejected by this radius
server.
successfulAuthenticationRequests
long
tmnxSubAuthPlcyRadSucc
ess
The value of tmnxSubAuthPlcyRadSuccess
indicates how many authentication
requests were accepted by this radius
server.
timedOutAuthenticationRequests
long
tmnxSubAuthPlcyRadTim
eout
The value of
tmnxSubAuthPlcyRadTimeout indicates
how many times this radius did not reply
to an authentication request within the
timeout.
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-159
E. 7450 ESS Release 7.0 statistics counters
Table E-32 svq statistics
5620 SAM counter name
Type
MIB counter name
Description
CustMultiSvcSiteEgrSchedPlcyPortStats
MIB table name: TIMETRA-SERV-MIB.custMultiSvcSiteEgrSchedPlcyPortStatsTable
Monitored class: svq.AggregationScheduler
forwardedOctets
UINT128
custEgrSchedPlcyPortStat
sFwdOct
The value of
custEgrSchedPlcyPortStatsFwdOct
indicates the number of forwarded
octets, as determined by the customer
multi service site egress scheduler policy.
forwardedPackets
UINT128
custEgrSchedPlcyPortStat
sFwdPkt
The value of
custEgrSchedPlcyPortStatsFwdPkt
indicates the number of forwarded
packets, as determined by the customer
multi service site egress scheduler policy.
portID
long
custEgrSchedPlcyPortStat
sPort
The value of
custEgrSchedPlcyPortStatsPort is used as
an index of the egress QoS scheduler of
this customer multi service site. When an
MSS assignment is an aps/ccag/lag in 'link'
mode, each member-port of the
aps/ccag/lag has its own scheduler. This
object refers to the TmnxPortID of these
member-ports.
CustMultiSvcSiteEgrSchedPlcyStats
MIB table name: TIMETRA-SERV-MIB.custMultiSvcSiteEgrSchedPlcyStatsTable
Monitored class: svq.AggregationScheduler
forwardedOctets
UINT128
custEgrSchedPlcyStatsFw
dOct
The value of the object
custEgrSchedPlcyStatsFwdOct indicates
the number of forwarded octets, as
determined by the customer multi service
site egress scheduler policy.
forwardedPackets
UINT128
custEgrSchedPlcyStatsFw
dPkt
The value of the object
custEgrSchedPlcyStatsFwdPkt indicates
the number of forwarded packets, as
determined by the customer multi service
site egress scheduler policy.
CustMultiSvcSiteIngSchedPlcyPortStats
MIB table name: TIMETRA-SERV-MIB.custMultiSvcSiteIngSchedPlcyPortStatsTable
Monitored class: svq.AggregationScheduler
forwardedOctets
UINT128
custIngSchedPlcyPortStat
sFwdOct
The value of
custIngSchedPlcyPortStatsFwdOct
indicates the number of forwarded
octets, as determined by the customer
multi service site ingress scheduler
policy.
forwardedPackets
UINT128
custIngSchedPlcyPortStat
sFwdPkt
The value of
custIngSchedPlcyPortStatsFwdPkt
indicates the number of forwarded
packets, as determined by the customer
multi service site ingress scheduler
policy.
(1 of 2)
E-160
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
portID
long
custIngSchedPlcyPortStat
sPort
The value of
custIngSchedPlcyPortStatsPort is used as
an index of the ingress QoS scheduler of
this customer multi service site. When an
MSS assignment is an aps/ccag/lag in 'link'
mode, each member-port of the
aps/ccag/lag has its own scheduler. This
object refers to the TmnxPortID of these
member-ports.
CustMultiSvcSiteIngSchedPlcyStats
MIB table name: TIMETRA-SERV-MIB.custMultiSvcSiteIngSchedPlcyStatsTable
Monitored class: svq.AggregationScheduler
forwardedOctets
UINT128
custIngSchedPlcyStatsFw
dOct
The value of the object
custIngSchedPlcyStatsFwdOct indicates
the number of forwarded octets, as
determined by the customer multi service
site ingress scheduler policy.
forwardedPackets
UINT128
custIngSchedPlcyStatsFw
dPkt
The value of the object
custIngSchedPlcyStatsFwdPkt indicates
the number of forwarded packets, as
determined by the customer multi service
site ingress scheduler policy.
(2 of 2)
Table E-33 svt statistics
5620 SAM counter name
Type
MIB counter name
Description
MirrorSdpBindingStats
MIB table name: TIMETRA-SDP-MIB.sdpBindBaseStatsTable
Monitored class: svt.MirrorSdpBinding
egressForwardedOctets
UINT128
sdpBindBaseStatsEgressF
orwardedOctets
.
egressForwardedPackets
UINT128
sdpBindBaseStatsEgressF
orwardedPackets
.
ingressDroppedOctets
UINT128
sdpBindBaseStatsIngDrop
Octets
.
ingressDroppedPackets
UINT128
sdpBindBaseStatsIngressD
roppedPackets
.
ingressForwardedOctets
UINT128
sdpBindBaseStatsIngFwdO
ctets
.
ingressForwardedPackets
UINT128
sdpBindBaseStatsIngressF
orwardedPackets
.
SdpBindingBaseStats
MIB table name: TIMETRA-SDP-MIB.sdpBindBaseStatsTable
Monitored classes:
•
•
svt.SpokeSdpBinding
svt.MeshSdpBinding
egressForwardedOctets
UINT128
sdpBindBaseStatsEgressF
orwardedOctets
.
(1 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-161
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
egressForwardedPackets
UINT128
sdpBindBaseStatsEgressF
orwardedPackets
.
ingressDroppedOctets
UINT128
sdpBindBaseStatsIngDrop
Octets
.
ingressDroppedPackets
UINT128
sdpBindBaseStatsIngressD
roppedPackets
.
ingressForwardedOctets
UINT128
sdpBindBaseStatsIngFwdO
ctets
.
ingressForwardedPackets
UINT128
sdpBindBaseStatsIngressF
orwardedPackets
.
SdpBindingIgmpSnpgErrorStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sdpBindIgmpSnpgStatsTable
Monitored classes:
•
•
svt.SpokeSdpBinding
svt.MeshSdpBinding
sdpBndIgmpSnpgImportPolicyDrops
long
sdpBndIgmpSnpgImportPo
licyDrops
The value of the object
sdpBndIgmpSnpgImportPolicyDrops
indicates the number of times an IGMP
Group or Source is dropped because of
applying an import policy on this SDP
Bind.
sdpBndIgmpSnpgMaxNumGroupsDr
ops
long
sdpBndIgmpSnpgMaxNum
GroupsDrops
The value of the object
sdpBndIgmpSnpgMaxNumGroupsDrops
indicates the number of times an IGMP
Group is dropped because of exceeding
the configured maximum number of
groups on this SDP Bind.
sdpBndIgmpSnpgMaxNumSourcesDr
ops
long
sdpBndIgmpSnpgMaxNum
SourcesDrops
The value of the object
sdpBndIgmpSnpgMaxNumSourcesDrops
indicates the number of times an IGMP
Source is dropped because of exceeding
the configured maximum number of
sources per group on this SDP Bind.
sdpBndIgmpSnpgMcacPolicyDrops
long
sdpBndIgmpSnpgMcacPoli
cyDrops
The value of the object
sdpBndIgmpSnpgMcacPolicyDrops
indicates the number of times an IGMP
Group is dropped because of applying a
multicast CAC policy on this SDP Bind.
sdpBndIgmpSnpgRxBadEncodedPkt
s
long
sdpBndIgmpSnpgRxBadEn
codedPkts
The value of the object
sdpBndIgmpSnpgRxBadEncodedPkts
indicates the number of IGMP packets
dropped on this SDP Bind because of a bad
encoding.
sdpBndIgmpSnpgRxBadIgmpChksm
Pkts
long
sdpBndIgmpSnpgRxBadIg
mpChksmPkts
The value of the object
sdpBndIgmpSnpgRxBadIgmpChksmPkts
indicates the number of dropped IGMP
packets on this SDP Bind because of a bad
IGMP header checksum.
sdpBndIgmpSnpgRxBadIpChksmPkt
s
long
sdpBndIgmpSnpgRxBadIp
ChksmPkts
The value of the object
sdpBndIgmpSnpgRxBadIpChksmPkts
indicates the number of dropped IGMP
packets on this SDP Bind because of a bad
IPv4 header checksum.
(2 of 5)
E-162
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBndIgmpSnpgRxBadLenPkts
long
sdpBndIgmpSnpgRxBadLe
nPkts
The value of the object
sdpBndIgmpSnpgRxBadLenPkts indicates
the number of IGMP packets dropped on
this SDP Bind because of a bad length.
sdpBndIgmpSnpgRxNoRtrAlertPkts
long
sdpBndIgmpSnpgRxNoRtr
AlertPkts
The value of the object
sdpBndIgmpSnpgRxNoRtrAlertPkts
indicates the number of IGMP packets
dropped on this SDP Bind because the
Router Alert Option in the IP packet is not
set.
sdpBndIgmpSnpgRxWrongVersionP
kts
long
sdpBndIgmpSnpgRxWrong
VersionPkts
The value of the object
sdpBndIgmpSnpgRxWrongVersionPkts
indicates the total number of IGMP
packets with a wrong version received on
this SDP Bind.
sdpBndIgmpSnpgRxZeroSrcAdrPkts
long
sdpBndIgmpSnpgRxZeroSr
cAdrPkts
The value of the object
sdpBndIgmpSnpgRxZeroSrcAdrPkts
indicates the number of IGMP packets
dropped on this SDP Bind because they
contain a zero source IPv4 address.
sdpBndIgmpSnpgSendQueryCfgDro
ps
long
sdpBndIgmpSnpgSendQue
ryCfgDrops
The value of the object
sdpBndIgmpSnpgSendQueryCfgDrops
indicates the number of times an IGMP
Query is dropped because the object
sdpBndIgmpSnpgCfgSendQueries for this
SDP Bind is set to 'enabled(1)'.
SdpBindingIgmpSnpgStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sdpBindIgmpSnpgStatsTable
Monitored classes:
svt.SpokeSdpBinding
svt.MeshSdpBinding
•
•
sdpBndIgmpSnpgFwdGenQueries
long
sdpBndIgmpSnpgFwdGen
Queries
The value of the object
sdpBndIgmpSnpgFwdGenQueries
indicates the number of IGMP General
Queries forwarded on this SDP Bind.
sdpBndIgmpSnpgFwdGrpSpecQueri
es
long
sdpBndIgmpSnpgFwdGrpS
pecQueries
The value of the object
sdpBndIgmpSnpgFwdGrpSpecQueries
indicates the number of IGMP
Group-Specific Queries forwarded on this
SDP Bind.
sdpBndIgmpSnpgFwdSrcSpecQueri
es
long
sdpBndIgmpSnpgFwdSrcS
pecQueries
The value of the object
sdpBndIgmpSnpgFwdSrcSpecQueries
indicates the number of IGMP
Group-And-Source-Specific Queries
forwarded on this SDP Bind.
sdpBndIgmpSnpgFwdUnknownType
long
sdpBndIgmpSnpgFwdUnkn
ownType
The value of the object
sdpBndIgmpSnpgFwdUnknownType
indicates the number of IGMP unknown
type packets forwarded on this SDP Bind.
sdpBndIgmpSnpgFwdV1Reports
long
sdpBndIgmpSnpgFwdV1Re
ports
The value of the object
sdpBndIgmpSnpgFwdV1Reports indicates
the number of IGMPv1 Reports forwarded
on this SDP Bind.
(3 of 5)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-163
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBndIgmpSnpgFwdV2Leaves
long
sdpBndIgmpSnpgFwdV2Le
aves
The value of the object
sdpBndIgmpSnpgFwdV2Leaves indicates
the number of IGMPv2 Leaves forwarded
on this SDP Bind.
sdpBndIgmpSnpgFwdV2Reports
long
sdpBndIgmpSnpgFwdV2Re
ports
The value of the object
sdpBndIgmpSnpgFwdV2Reports indicates
the number of IGMPv2 Reports forwarded
on this SDP Bind.
sdpBndIgmpSnpgFwdV3Reports
long
sdpBndIgmpSnpgFwdV3Re
ports
The value of the object
sdpBndIgmpSnpgFwdV3Reports indicates
the number of IGMPv3 Reports forwarded
on this SDP Bind.
sdpBndIgmpSnpgRxGenQueries
long
sdpBndIgmpSnpgRxGenQu
eries
The value of the object
sdpBndIgmpSnpgRxGenQueries indicates
the number of IGMP General Queries
received on this SDP Bind.
sdpBndIgmpSnpgRxGrpSpecQuerie
s
long
sdpBndIgmpSnpgRxGrpSp
ecQueries
The value of the object
sdpBndIgmpSnpgRxGrpSpecQueries
indicates the number of IGMP
Group-Specific Queries received on this
SDP Bind.
sdpBndIgmpSnpgRxSrcSpecQueries
long
sdpBndIgmpSnpgRxSrcSpe
cQueries
The value of the object
sdpBndIgmpSnpgRxSrcSpecQueries
indicates the number of IGMP
Group-And-Source-Specific Queries
received on this SDP Bind.
sdpBndIgmpSnpgRxUnknownType
long
sdpBndIgmpSnpgRxUnkno
wnType
The value of the object
sdpBndIgmpSnpgRxUnknownType
indicates the number of IGMP unknown
type packets received on this SDP Bind.
sdpBndIgmpSnpgRxV1Reports
long
sdpBndIgmpSnpgRxV1Rep
orts
The value of the object
sdpBndIgmpSnpgRxV1Reports indicates
the number of IGMPv1 Reports received
on this SDP Bind.
sdpBndIgmpSnpgRxV2Leaves
long
sdpBndIgmpSnpgRxV2Lea
ves
The value of the object
sdpBndIgmpSnpgRxV2Leaves indicates the
number of IGMPv2 Leaves received on this
SDP Bind.
sdpBndIgmpSnpgRxV2Reports
long
sdpBndIgmpSnpgRxV2Rep
orts
The value of the object
sdpBndIgmpSnpgRxV2Reports indicates
the number of IGMPv2 Reports received
on this SDP Bind.
sdpBndIgmpSnpgRxV3Reports
long
sdpBndIgmpSnpgRxV3Rep
orts
The value of the object
sdpBndIgmpSnpgRxV3Reports indicates
the number of IGMPv3 Reports received
on this SDP Bind.
sdpBndIgmpSnpgTxGenQueries
long
sdpBndIgmpSnpgTxGenQu
eries
The value of the object
sdpBndIgmpSnpgTxGenQueries indicates
the number of IGMP General Queries
transmitted on this SDP Bind.
sdpBndIgmpSnpgTxGrpSpecQuerie
s
long
sdpBndIgmpSnpgTxGrpSp
ecQueries
The value of the object
sdpBndIgmpSnpgTxGrpSpecQueries
indicates the number of IGMP
Group-Specific Queries transmitted on
this SDP Bind.
(4 of 5)
E-164
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBndIgmpSnpgTxSrcSpecQueries
long
sdpBndIgmpSnpgTxSrcSpe
cQueries
The value of the object
sdpBndIgmpSnpgTxSrcSpecQueries
indicates the number of IGMP
Group-And-Source-Specific Queries
transmitted on this SDP Bind.
sdpBndIgmpSnpgTxV1Reports
long
sdpBndIgmpSnpgTxV1Rep
orts
The value of the object
sdpBndIgmpSnpgTxV1Reports indicates
the number of IGMPv1 Reports
transmitted on this SDP Bind.
sdpBndIgmpSnpgTxV2Leaves
long
sdpBndIgmpSnpgTxV2Lea
ves
The value of the object
sdpBndIgmpSnpgTxV2Leaves indicates the
number of IGMPv2 Leaves transmitted on
this SDP Bind.
sdpBndIgmpSnpgTxV2Reports
long
sdpBndIgmpSnpgTxV2Rep
orts
The value of the object
sdpBndIgmpSnpgTxV2Reports indicates
the number of IGMPv2 Reports
transmitted on this SDP Bind.
sdpBndIgmpSnpgTxV3Reports
long
sdpBndIgmpSnpgTxV3Rep
orts
The value of the object
sdpBndIgmpSnpgTxV3Reports indicates
the number of IGMPv3 Reports
transmitted on this SDP Bind.
TunnelKeepAliveStats
MIB table name: TIMETRA-SDP-MIB.sdpInfoTable
Monitored class: svt.Tunnel
lateHelloResponses
long
sdpKeepAliveNumLateHel
loResponseMessages
The number of SDP Echo Response
messages received after the
corresponding Request timeout timer
expired.
receivedHelloMessages
long
sdpKeepAliveNumHelloRe
sponseMessages
The number of SDP Echo Response
messages received since the keep-alive
was administratively enabled or the
counter was cleared.
transmittedHelloMessages
long
sdpKeepAliveNumHelloRe
questMessages
The number of SDP Echo Request
messages transmitted since the
keep-alive was administratively enabled
or the counter was cleared.
(5 of 5)
Table E-34 vpls statistics
5620 SAM counter name
Type
MIB counter name
Description
CircuitDhcpRelayCfgStats
MIB table name: TIMETRA-SDP-MIB.sdpBindDhcpStatsTable
Monitored class: svt.SdpBinding
sdpBindDhcpStatsClntDropdPckts
long
sdpBindDhcpStatsClntDro
pdPckts
The value of the object
sdpBindDhcpStatsClntDropdPckts
indicates the number of DHCP client
packets that have been dropped on this
SDP bind.
(1 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-165
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBindDhcpStatsClntForwdPckts
long
sdpBindDhcpStatsClntFor
wdPckts
The value of the object
sdpBindDhcpStatsClntForwdPckts
indicates the number of DHCP client
packets that have been forwarded on this
SDP bind.
sdpBindDhcpStatsClntProxLSPckts
long
sdpBindDhcpStatsClntPro
xLSPckts
The value of the object
sdpBindDhcpStatsClntProxLSPckts
indicates the number of DHCP client
packets that have been proxied on this
SDP bind based on a lease state. The lease
itself can have been obtained from a
DHCP or RADIUS server. This is the so
called lease split functionality.
sdpBindDhcpStatsClntProxRadPckt
s
long
sdpBindDhcpStatsClntPro
xRadPckts
The value of the object
sdpBindDhcpStatsClntProxRadPckts
indicates the number of DHCP client
packets that have been proxied on this
SDP bind based on data received from a
RADIUS server.
sdpBindDhcpStatsClntSnoopdPckts
long
sdpBindDhcpStatsClntSno
opdPckts
The value of the object
sdpBindDhcpStatsClntSnoopdPckts
indicates the number of DHCP client
packets that have been snooped on this
SDP bind.
sdpBindDhcpStatsGenForceRenPck
ts
long
sdpBindDhcpStatsGenFor
ceRenPckts
The value of the object
sdpBindDhcpStatsGenForceRenPckts
indicates the number of DHCP
FORCERENEW messages spoofed on this
SDP bind to the DHCP clients.
sdpBindDhcpStatsGenReleasePckts
long
sdpBindDhcpStatsGenRel
easePckts
The value of the object
sdpBindDhcpStatsGenReleasePckts
indicates the number of DHCP RELEASE
messages spoofed on this SDP bind to the
DHCP server.
sdpBindDhcpStatsSrvrDropdPckts
long
sdpBindDhcpStatsSrvrDro
pdPckts
The value of the object
sdpBindDhcpStatsSrvrDropdPckts
indicates the number of DHCP server
packets that have been dropped on this
SDP bind.
sdpBindDhcpStatsSrvrForwdPckts
long
sdpBindDhcpStatsSrvrFor
wdPckts
The value of the object
sdpBindDhcpStatsSrvrForwdPckts
indicates the number of DHCP server
packets that have been forwarded on this
SDP bind.
sdpBindDhcpStatsSrvrSnoopdPckts
long
sdpBindDhcpStatsSrvrSno
opdPckts
The value of the object
sdpBindDhcpStatsSrvrSnoopdPckts
indicates the number of DHCP server
packets that have been snooped on this
SDP bind.
InterfacePimSnoopingStats
MIB table name: TIMETRA-PIM-SNOOPING-MIB.tmnxPimSnpgIfStatsTable
Monitored class: vpls.InterfacePimSnooping
(2 of 15)
E-166
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
tmnxPimSnpgIfJoinPolicyDrops
long
tmnxPimSnpgIfJoinPolicy
Drops
The value of
tmnxPimSnpgIfJoinPolicyDrops indicates
the number of times the join policy match
resulted in dropping PIM Join-Prune
Message or one of the source group
contained in the message.
tmnxPimSnpgIfRxBadChecksumDsc
rd
long
tmnxPimSnpgIfRxBadChe
cksumDscrd
The value of
tmnxPimSnpgIfRxBadChecksumDscrd
indicates the number of PIM messages
received on this interface which were
discarded because of bad checksum.
tmnxPimSnpgIfRxBadEncodings
long
tmnxPimSnpgIfRxBadEnco
dings
The value of
tmnxPimSnpgIfRxBadEncodings indicates
the number of PIM messages with bad
encodings received on this interface.
tmnxPimSnpgIfRxBadVersionDscrd
long
tmnxPimSnpgIfRxBadVers
ionDscrd
The value of
tmnxPimSnpgIfRxBadVersionDscrd
indicates the number of PIM messages
with bad versions received on this
interface.
tmnxPimSnpgIfRxHellos
long
tmnxPimSnpgIfRxHellos
The value of tmnxPimSnpgIfRxHellos
indicates the number of PIM hello
messages received on this interface.
tmnxPimSnpgIfRxHellosDropped
long
tmnxPimSnpgIfRxHellosDr
opped
The value of
tmnxPimSnpgIfRxHellosDropped indicates
the number of PIM Hello messages which
were received on this interface but were
dropped.
tmnxPimSnpgIfRxJoinPruneErrs
long
tmnxPimSnpgIfRxJoinPru
neErrs
The value of
tmnxPimSnpgIfRxJoinPruneErrs indicates
the number of errors while processing
Join-Prune messages received on this
interface.
tmnxPimSnpgIfRxJoinPrunes
long
tmnxPimSnpgIfRxJoinPru
nes
The value of tmnxPimSnpgIfRxJoinPrunes
indicates the number of PIM Join Prune
messages received on this interface.
tmnxPimSnpgIfRxNbrUnknown
long
tmnxPimSnpgIfRxNbrUnk
nown
The value of
tmnxPimSnpgIfRxNbrUnknown indicates
the number of PIM messages (other than
Hello messages) which were received on
this interface and were rejected because
the adjacency with the neighbor router
was not already established.
tmnxPimSnpgIfRxPkts
long
tmnxPimSnpgIfRxPkts
The value of tmnxPimSnpgIfRxPkts
indicates the number of multicast data
packets received on this interface.
tmnxPimSnpgIfSGTypes
long
tmnxPimSnpgIfSGTypes
The value of tmnxPimSnpgIfSGTypes
indicates the number of (S,G) entries in
tmnxPimSnpgIfGrpSrcTable.
tmnxPimSnpgIfStarGTypes
long
tmnxPimSnpgIfStarGType
s
The value of tmnxPimSnpgIfStarGTypes
indicates the number of (*,G) entries in
tmnxPimSnpgIfGrpSrcTable.
tmnxPimSnpgIfTxJoinPrunes
long
tmnxPimSnpgIfTxJoinPru
nes
The value of tmnxPimSnpgIfTxJoinPrunes
indicates the number of PIM Join Prune
messages transmitted on this interface.
(3 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-167
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
tmnxPimSnpgIfTxPkts
long
tmnxPimSnpgIfTxPkts
The value of tmnxPimSnpgIfTxPkts
indicates the number of multicast data
packets transmitted on this interface.
L2AccessInterfaceIgmpSnpgErrorStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sapIgmpSnpgStatsTable
Monitored classes:
•
•
•
vpls.AbstractL2AccessInterface
vpls.IL2AccessInterface
mvpls.IL2AccessInterface
sapIgmpSnpgImportPolicyDrops
long
sapIgmpSnpgImportPolicy
Drops
The value of the object
sapIgmpSnpgImportPolicyDrops indicates
the number of times an IGMP Group or
Source is dropped because of applying an
import policy on this SAP.
sapIgmpSnpgMaxNumGroupsDrops
long
sapIgmpSnpgMaxNumGro
upsDrops
The value of the object
sapIgmpSnpgMaxNumGroupsDrops
indicates the number of times an IGMP
Group is dropped because of exceeding
the configured maximum number of
groups on this SAP.
sapIgmpSnpgMaxNumSourcesDrops
long
sapIgmpSnpgMaxNumSour
cesDrops
The value of the object
sapIgmpSnpgMaxNumSourcesDrops
indicates the number of times an IGMP
Source is dropped because of exceeding
the configured maximum number of
sources per group on this SAP.
sapIgmpSnpgMcacPolicyDrops
long
sapIgmpSnpgMcacPolicyD
rops
The value of the object
sapIgmpSnpgMcacPolicyDrops indicates
the number of times an IGMP Group is
dropped because of applying a multicast
CAC policy on this SAP.
sapIgmpSnpgMcsFailures
long
sapIgmpSnpgMcsFailures
The value of the object
sapIgmpSnpgMcsFailures indicates the
number of times an IGMP Group on this
SAP could not be synced to the MCS
(multi-chassis synchronization) database.
sapIgmpSnpgRxBadEncodedPkts
long
sapIgmpSnpgRxBadEncod
edPkts
The value of the object
sapIgmpSnpgRxBadEncodedPkts indicates
the number of IGMP packets dropped on
this SAP because of a bad encoding.
sapIgmpSnpgRxBadIgmpChksmPkts
long
sapIgmpSnpgRxBadIgmpC
hksmPkts
The value of the object
sapIgmpSnpgRxBadIgmpChksmPkts
indicates the number of dropped IGMP
packets on this SAP because of a bad IGMP
header checksum.
sapIgmpSnpgRxBadIpChksmPkts
long
sapIgmpSnpgRxBadIpChks
mPkts
The value of the object
sapIgmpSnpgRxBadIpChksmPkts indicates
the number of dropped IGMP packets on
this SAP because of a bad IPv4 header
checksum.
sapIgmpSnpgRxBadLenPkts
long
sapIgmpSnpgRxBadLenPkt
s
The value of the object
sapIgmpSnpgRxBadLenPkts indicates the
number of IGMP packets dropped on this
SAP because of a bad length.
(4 of 15)
E-168
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapIgmpSnpgRxNoRtrAlertPkts
long
sapIgmpSnpgRxNoRtrAler
tPkts
The value of the object
sapIgmpSnpgRxNoRtrAlertPkts indicates
the number of IGMP packets dropped on
this SAP because the Router Alert Option
in the IP packet is not set.
sapIgmpSnpgRxWrongVersionPkts
long
sapIgmpSnpgRxWrongVer
sionPkts
The value of the object
sapIgmpSnpgRxWrongVersionPkts
indicates the total number of IGMP
packets with a wrong version received on
this SAP.
sapIgmpSnpgRxZeroSrcAdrPkts
long
sapIgmpSnpgRxZeroSrcAd
rPkts
The value of the object
sapIgmpSnpgRxZeroSrcAdrPkts indicates
the number of IGMP packets dropped on
this SAP because they contain a zero
source IPv4 address.
sapIgmpSnpgSendQueryCfgDrops
long
sapIgmpSnpgSendQueryCf
gDrops
The value of the object
sapIgmpSnpgSendQueryCfgDrops
indicates the number of times an IGMP
Query is dropped because the object
sapIgmpSnpgCfgSendQueries for this SAP
is set to 'enabled(1)'.
L2AccessInterfaceIgmpSnpgStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sapIgmpSnpgStatsTable
Monitored classes:
vpls.AbstractL2AccessInterface
vpls.IL2AccessInterface
mvpls.IL2AccessInterface
•
•
•
sapIgmpSnpgFwdGenQueries
long
sapIgmpSnpgFwdGenQuer
ies
The value of the object
sapIgmpSnpgFwdGenQueries indicates
the number of IGMP General Queries
forwarded on this SAP.
sapIgmpSnpgFwdGrpSpecQueries
long
sapIgmpSnpgFwdGrpSpec
Queries
The value of the object
sapIgmpSnpgFwdGrpSpecQueries
indicates the number of IGMP
Group-Specific Queries forwarded on this
SAP.
sapIgmpSnpgFwdSrcSpecQueries
long
sapIgmpSnpgFwdSrcSpec
Queries
The value of the object
sapIgmpSnpgFwdSrcSpecQueries indicates
the number of IGMP
Group-And-Source-Specific Queries
forwarded on this SAP.
sapIgmpSnpgFwdUnknownType
long
sapIgmpSnpgFwdUnknow
nType
The value of the object
sapIgmpSnpgFwdUnknownType indicates
the number of IGMP unknown type
packets forwarded on this SAP.
sapIgmpSnpgFwdV1Reports
long
sapIgmpSnpgFwdV1Repor
ts
The value of the object
sapIgmpSnpgFwdV1Reports indicates the
number of IGMPv1 Reports forwarded on
this SAP.
sapIgmpSnpgFwdV2Leaves
long
sapIgmpSnpgFwdV2Leave
s
The value of the object
sapIgmpSnpgFwdV2Leaves indicates the
number of IGMPv2 Leaves forwarded on
this SAP.
(5 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-169
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapIgmpSnpgFwdV2Reports
long
sapIgmpSnpgFwdV2Repor
ts
The value of the object
sapIgmpSnpgFwdV2Reports indicates the
number of IGMPv2 Reports forwarded on
this SAP.
sapIgmpSnpgFwdV3Reports
long
sapIgmpSnpgFwdV3Repor
ts
The value of the object
sapIgmpSnpgFwdV3Reports indicates the
number of IGMPv3 Reports forwarded on
this SAP.
sapIgmpSnpgRxGenQueries
long
sapIgmpSnpgRxGenQueri
es
The value of the object
sapIgmpSnpgRxGenQueries indicates the
number of IGMP General Queries received
on this SAP.
sapIgmpSnpgRxGrpSpecQueries
long
sapIgmpSnpgRxGrpSpecQ
ueries
The value of the object
sapIgmpSnpgRxGrpSpecQueries indicates
the number of IGMP Group-Specific
Queries received on this SAP.
sapIgmpSnpgRxSrcSpecQueries
long
sapIgmpSnpgRxSrcSpecQu
eries
The value of the object
sapIgmpSnpgRxSrcSpecQueries indicates
the number of IGMP
Group-And-Source-Specific Queries
received on this SAP.
sapIgmpSnpgRxUnknownType
long
sapIgmpSnpgRxUnknownT
ype
The value of the object
sapIgmpSnpgRxUnknownType indicates
the number of IGMP unknown type
packets received on this SAP.
sapIgmpSnpgRxV1Reports
long
sapIgmpSnpgRxV1Reports
The value of the object
sapIgmpSnpgRxV1Reports indicates the
number of IGMPv1 Reports received on
this SAP.
sapIgmpSnpgRxV2Leaves
long
sapIgmpSnpgRxV2Leaves
The value of the object
sapIgmpSnpgRxV2Leaves indicates the
number of IGMPv2 Leaves received on this
SAP.
sapIgmpSnpgRxV2Reports
long
sapIgmpSnpgRxV2Reports
The value of the object
sapIgmpSnpgRxV2Reports indicates the
number of IGMPv2 Reports received on
this SAP.
sapIgmpSnpgRxV3Reports
long
sapIgmpSnpgRxV3Reports
The value of the object
sapIgmpSnpgRxV3Reports indicates the
number of IGMPv3 Reports received on
this SAP.
sapIgmpSnpgTxGenQueries
long
sapIgmpSnpgTxGenQueri
es
The value of the object
sapIgmpSnpgTxGenQueries indicates the
number of IGMP General Queries
transmitted on this SAP.
sapIgmpSnpgTxGrpSpecQueries
long
sapIgmpSnpgTxGrpSpecQ
ueries
The value of the object
sapIgmpSnpgTxGrpSpecQueries indicates
the number of IGMP Group-Specific
Queries transmitted on this SAP.
sapIgmpSnpgTxSrcSpecQueries
long
sapIgmpSnpgTxSrcSpecQu
eries
The value of the object
sapIgmpSnpgTxSrcSpecQueries indicates
the number of IGMP
Group-And-Source-Specific Queries
transmitted on this SAP.
(6 of 15)
E-170
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapIgmpSnpgTxV1Reports
long
sapIgmpSnpgTxV1Reports
The value of the object
sapIgmpSnpgTxV1Reports indicates the
number of IGMPv1 Reports transmitted on
this SAP.
sapIgmpSnpgTxV2Leaves
long
sapIgmpSnpgTxV2Leaves
The value of the object
sapIgmpSnpgTxV2Leaves indicates the
number of IGMPv2 Leaves transmitted on
this SAP.
sapIgmpSnpgTxV2Reports
long
sapIgmpSnpgTxV2Reports
The value of the object
sapIgmpSnpgTxV2Reports indicates the
number of IGMPv2 Reports transmitted on
this SAP.
sapIgmpSnpgTxV3Reports
long
sapIgmpSnpgTxV3Reports
The value of the object
sapIgmpSnpgTxV3Reports indicates the
number of IGMPv3 Reports transmitted on
this SAP.
L2AccessInterfaceMldMvrStats
MIB table name: TIMETRA-MLD-SNOOPING-MIB.sapMldSnpgStatsTable
Monitored class: vpls.AbstractL2AccessInterface
sapMldSnpgMvrFromVplsCfgDrops
long
sapMldSnpgMvrFromVplsC
fgDrops
The value of the object
sapMldSnpgMvrFromVplsCfgDrops
indicates the number of times an MLD
group or Query is dropped because of
applying the
sapMldSnpgCfgMvrFromVplsId
configuration on this SAP.
sapMldSnpgMvrToSapCfgDrops
long
sapMldSnpgMvrToSapCfgD
rops
The value of the object
sapMldSnpgMvrToSapCfgDrops indicates
the number times an MLD Report or Query
is dropped because of applying the
sapMldSnpgCfgMvrToSapPortId and
sapMldSnpgCfgMvrToSapEncapVal
configuration on this SAP.
L2AccessInterfaceMldSnpgErrorStats
MIB table name: TIMETRA-MLD-SNOOPING-MIB.sapMldSnpgStatsTable
Monitored class: vpls.AbstractL2AccessInterface
sapMldSnpgImportPolicyDrops
long
sapMldSnpgImportPolicyD
rops
The value of the object
sapMldSnpgImportPolicyDrops indicates
the number of times an MLD group or
source is dropped because of applying an
import policy on this SAP.
sapMldSnpgMaxNumGroupsDrops
long
sapMldSnpgMaxNumGrou
psDrops
The value of the object
sapMldSnpgMaxNumGroupsDrops
indicates the number of times an MLD
group is dropped because of exceeding
the configured maximum number of
groups on this SAP.
sapMldSnpgMcsFailures
long
sapMldSnpgMcsFailures
The value of the object
sapMldSnpgMcsFailures indicates the
number of times an MLD group on this SAP
could not be synced to the MCS
(multi-chassis synchronization) database.
(7 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-171
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapMldSnpgRxBadEncodedPkts
long
sapMldSnpgRxBadEncode
dPkts
The value of the object
sapMldSnpgRxBadEncodedPkts indicates
the number of MLD packets dropped on
this SAP because of a bad encoding.
sapMldSnpgRxBadLenPkts
long
sapMldSnpgRxBadLenPkts
The value of the object
sapMldSnpgRxBadLenPkts indicates the
number of MLD packets dropped on this
SAP because of a bad length.
sapMldSnpgRxBadMldChksmPkts
long
sapMldSnpgRxBadMldChks
mPkts
The value of the object
sapMldSnpgRxBadMldChksmPkts indicates
the number of dropped MLD packets on
this SAP because of a bad MLD header
checksum.
sapMldSnpgRxNoRtrAlertPkts
long
sapMldSnpgRxNoRtrAlertP
kts
The value of the object
sapMldSnpgRxNoRtrAlertPkts indicates
the number of MLD packets dropped on
this SAP because the Router Alert Option
in the IP packet is not set.
sapMldSnpgRxWrongVersionPkts
long
sapMldSnpgRxWrongVersi
onPkts
The value of the object
sapMldSnpgRxWrongVersionPkts indicates
the total number of MLD packets with a
wrong version received on this SAP.
sapMldSnpgRxZeroSrcAdrPkts
long
sapMldSnpgRxZeroSrcAdr
Pkts
The value of the object
sapMldSnpgRxZeroSrcAdrPkts indicates
the number of MLD packets dropped on
this SAP because they contain a zero
source IPv6 address.
sapMldSnpgSendQueryCfgDrops
long
sapMldSnpgSendQueryCfg
Drops
The value of the object
sapMldSnpgSendQueryCfgDrops indicates
the number of times an MLD Query is
dropped because the object
sapMldSnpgCfgSendQueries for this SAP is
set to 'inService(2)'.
L2AccessInterfaceMldSnpgStats
MIB table name: TIMETRA-MLD-SNOOPING-MIB.sapMldSnpgStatsTable
Monitored class: vpls.AbstractL2AccessInterface
sapMldSnpgFwdGenQueries
long
sapMldSnpgFwdGenQueri
es
The value of the object
sapMldSnpgFwdGenQueries indicates the
number of MLD General Queries
forwarded on this SAP.
sapMldSnpgFwdGrpSpecQueries
long
sapMldSnpgFwdGrpSpecQ
ueries
The value of the object
sapMldSnpgFwdGrpSpecQueries indicates
the number of MLD Group-Specific
Queries forwarded on this SAP.
sapMldSnpgFwdSrcSpecQueries
long
sapMldSnpgFwdSrcSpecQ
ueries
The value of the object
sapMldSnpgFwdSrcSpecQueries indicates
the number of MLD
Group-And-Source-Specific Queries
forwarded on this SAP.
sapMldSnpgFwdUnknownType
long
sapMldSnpgFwdUnknown
Type
The value of the object
sapMldSnpgFwdUnknownType indicates
the number of MLD unknown type packets
forwarded on this SAP.
(8 of 15)
E-172
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapMldSnpgFwdV1Leaves
long
sapMldSnpgFwdV1Leaves
The value of the object
sapMldSnpgFwdV1Leaves indicates the
number of MLDv1 Leaves forwarded on
this SAP.
sapMldSnpgFwdV1Reports
long
sapMldSnpgFwdV1Reports
The value of the object
sapMldSnpgFwdV1Reports indicates the
number of MLDv1 Reports forwarded on
this SAP.
sapMldSnpgFwdV2Reports
long
sapMldSnpgFwdV2Reports
The value of the object
sapMldSnpgFwdV2Reports indicates the
number of MLDv2 Reports forwarded on
this SAP.
sapMldSnpgRxGenQueries
long
sapMldSnpgRxGenQueries
The value of the object
sapMldSnpgRxGenQueries indicates the
number of MLD General Queries received
on this SAP.
sapMldSnpgRxGrpSpecQueries
long
sapMldSnpgRxGrpSpecQu
eries
The value of the object
sapMldSnpgRxGrpSpecQueries indicates
the number of MLD Group-Specific
Queries received on this SAP.
sapMldSnpgRxLocalScopePkts
long
sapMldSnpgRxLocalScope
Pkts
The value of the object
sapMldSnpgRxLocalScopePkts indicates
the number of MLD packets received on
the link-local scope IPv6 multicast
address.
sapMldSnpgRxRsvdScopePkts
long
sapMldSnpgRxRsvdScopeP
kts
The value of the object
sapMldSnpgRxRsvdScopePkts indicates
the number of MLD packets received on
the reserved scope IPv6 multicast
address.
sapMldSnpgRxSrcSpecQueries
long
sapMldSnpgRxSrcSpecQue
ries
The value of the object
sapMldSnpgRxSrcSpecQueries indicates
the number of MLD
Group-And-Source-Specific Queries
received on this SAP.
sapMldSnpgRxUnknownType
long
sapMldSnpgRxUnknownTy
pe
The value of the object
sapMldSnpgRxUnknownType indicates the
number of MLD unknown type packets
received on this SAP.
sapMldSnpgRxV1Leaves
long
sapMldSnpgRxV1Leaves
The value of the object
sapMldSnpgRxV1Leaves indicates the
number of MLDv1 Leaves received on this
SAP.
sapMldSnpgRxV1Reports
long
sapMldSnpgRxV1Reports
The value of the object
sapMldSnpgRxV1Reports indicates the
number of MLDv1 Reports received on this
SAP.
sapMldSnpgRxV2Reports
long
sapMldSnpgRxV2Reports
The value of the object
sapMldSnpgRxV2Reports indicates the
number of MLDv2 Reports received on this
SAP.
sapMldSnpgTxGenQueries
long
sapMldSnpgTxGenQueries
The value of the object
sapMldSnpgTxGenQueries indicates the
number of MLD General Queries
transmitted on this SAP.
(9 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-173
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapMldSnpgTxGrpSpecQueries
long
sapMldSnpgTxGrpSpecQu
eries
The value of the object
sapMldSnpgTxGrpSpecQueries indicates
the number of MLD Group-Specific
Queries transmitted on this SAP.
sapMldSnpgTxSrcSpecQueries
long
sapMldSnpgTxSrcSpecQue
ries
The value of the object
sapMldSnpgTxSrcSpecQueries indicates
the number of MLD
Group-And-Source-Specific Queries
transmitted on this SAP.
sapMldSnpgTxV1Leaves
long
sapMldSnpgTxV1Leaves
The value of the object
sapMldSnpgTxV1Leaves indicates the
number of MLDv1 Leaves transmitted on
this SAP.
sapMldSnpgTxV1Reports
long
sapMldSnpgTxV1Reports
The value of the object
sapMldSnpgTxV1Reports indicates the
number of MLDv1 Reports transmitted on
this SAP.
sapMldSnpgTxV2Reports
long
sapMldSnpgTxV2Reports
The value of the object
sapMldSnpgTxV2Reports indicates the
number of MLDv2 Reports transmitted on
this SAP.
L2AccessInterfaceMvrStats
MIB table name: ALCATEL-IGMP-SNOOPING-MIB.sapIgmpSnpgStatsTable
Monitored class: vpls.AbstractL2AccessInterface
sapIgmpSnpgMvrFromVplsCfgDrops
long
sapIgmpSnpgMvrFromVpls
CfgDrops
The value of the object
sapIgmpSnpgMvrFromVplsCfgDrops
indicates the number of times an IGMP
Group or Query is dropped because of
applying the
sapIgmpSnpgCfgMvrFromVplsId
configuration on this SAP.
sapIgmpSnpgMvrToSapCfgDrops
long
sapIgmpSnpgMvrToSapCfg
Drops
The value of the object
sapIgmpSnpgMvrToSapCfgDrops indicates
the number times an IGMP Report or
Query is dropped because of applying the
sapIgmpSnpgCfgMvrToSapPortId and
sapIgmpSnpgCfgMvrToSapEncapVal
configuration on this SAP.
L2AccessItfDhcpRelayCfgStats
MIB table name: TIMETRA-SAP-MIB.sapTlsDhcpStatsTable
Monitored class: vpls.AbstractL2AccessInterface
sapTlsDhcpStatsClntDropdPckts
long
sapTlsDhcpStatsClntDrop
dPckts
The value of the object
sapTlsDhcpStatsClntDropdPckts indicates
the number of DHCP client packets that
have been dropped on this SAP.
sapTlsDhcpStatsClntForwdPckts
long
sapTlsDhcpStatsClntForw
dPckts
The value of the object
sapTlsDhcpStatsClntForwdPckts indicates
the number of DHCP client packets that
have been forwarded on this SAP.
(10 of 15)
E-174
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sapTlsDhcpStatsClntProxLSPckts
long
sapTlsDhcpStatsClntProxL
SPckts
The value of the object
sapTlsDhcpStatsClntProxLSPckts indicates
the number of DHCP client packets that
have been proxied on this SAP based on a
lease state. The lease itself can have
been obtained from a DHCP or RADIUS
server. This is the so called lease split
functionality.
sapTlsDhcpStatsClntProxRadPckts
long
sapTlsDhcpStatsClntProx
RadPckts
The value of the object
sapTlsDhcpStatsClntProxRadPckts
indicates the number of DHCP client
packets that have been proxied on this
SAP based on data received from a RADIUS
server.
sapTlsDhcpStatsClntSnoopdPckts
long
sapTlsDhcpStatsClntSnoo
pdPckts
The value of the object
sapTlsDhcpStatsClntSnoopdPckts
indicates the number of DHCP client
packets that have been snooped on this
SAP.
sapTlsDhcpStatsGenForceRenPckts
long
sapTlsDhcpStatsGenForce
RenPckts
The value of the object
sapTlsDhcpStatsGenForceRenPckts
indicates the number of DHCP
FORCERENEW messages spoofed on this
SAP to the DHCP clients.
sapTlsDhcpStatsGenReleasePckts
long
sapTlsDhcpStatsGenRelea
sePckts
The value of the object
sapTlsDhcpStatsGenReleasePckts
indicates the number of DHCP RELEASE
messages spoofed on this SAP to the DHCP
server.
sapTlsDhcpStatsSrvrDropdPckts
long
sapTlsDhcpStatsSrvrDrop
dPckts
The value of the object
sapTlsDhcpStatsSrvrDropdPckts indicates
the number of DHCP server packets that
have been dropped on this SAP.
sapTlsDhcpStatsSrvrForwdPckts
long
sapTlsDhcpStatsSrvrForw
dPckts
The value of the object
sapTlsDhcpStatsSrvrForwdPckts indicates
the number of DHCP server packets that
have been forwarded on this SAP.
sapTlsDhcpStatsSrvrSnoopdPckts
long
sapTlsDhcpStatsSrvrSnoo
pdPckts
The value of the object
sapTlsDhcpStatsSrvrSnoopdPckts
indicates the number of DHCP server
packets that have been snooped on this
SAP.
SdpBindingMldSnpgErrorStats
MIB table name: TIMETRA-MLD-SNOOPING-MIB.sdpBindMldSnpgStatsTable
Monitored class: vpls.SdpBindingMldSnpgCfg
sdpBndMldSnpgImportPolicyDrops
long
sdpBndMldSnpgImportPoli
cyDrops
The value of the object
sdpBndMldSnpgImportPolicyDrops
indicates the number of times an MLD
group or source is dropped because of
applying an import policy on this SDP
Bind.
(11 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-175
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBndMldSnpgMaxNumGroupsDro
ps
long
sdpBndMldSnpgMaxNumG
roupsDrops
The value of the object
sdpBndMldSnpgMaxNumGroupsDrops
indicates the number of times an MLD
group is dropped because of exceeding
the configured maximum number of
groups on this SDP Bind.
sdpBndMldSnpgRxBadEncodedPkts
long
sdpBndMldSnpgRxBadEnc
odedPkts
The value of the object
sdpBndMldSnpgRxBadEncodedPkts
indicates the number of MLD packets
dropped on this SDP Bind because of a bad
encoding.
sdpBndMldSnpgRxBadLenPkts
long
sdpBndMldSnpgRxBadLen
Pkts
The value of the object
sdpBndMldSnpgRxBadLenPkts indicates
the number of MLD packets dropped on
this SDP Bind because of a bad length.
sdpBndMldSnpgRxBadMldChksmPkt
s
long
sdpBndMldSnpgRxBadMld
ChksmPkts
The value of the object
sdpBndMldSnpgRxBadMldChksmPkts
indicates the number of dropped MLD
packets on this SDP Bind because of a bad
MLD header checksum.
sdpBndMldSnpgRxLocalScopePkts
long
sdpBndMldSnpgRxLocalSc
opePkts
The value of the object
sdpBndMldSnpgRxLocalScopePkts
indicates the number of MLD packets
received on the link-local scope IPv6
multicast address.
sdpBndMldSnpgRxNoRtrAlertPkts
long
sdpBndMldSnpgRxNoRtrAl
ertPkts
The value of the object
sdpBndMldSnpgRxNoRtrAlertPkts
indicates the number of MLD packets
dropped on this SDP Bind because the
Router Alert Option in the IP packet is not
set.
sdpBndMldSnpgRxRsvdScopePkts
long
sdpBndMldSnpgRxRsvdSco
pePkts
The value of the object
sdpBndMldSnpgRxRsvdScopePkts
indicates the number of MLD packets
received on the reserved scope IPv6
multicast address.
sdpBndMldSnpgRxWrongVersionPkt
s
long
sdpBndMldSnpgRxWrongV
ersionPkts
The value of the object
sdpBndMldSnpgRxWrongVersionPkts
indicates the total number of MLD packets
with a wrong version received on this SDP
Bind.
sdpBndMldSnpgRxZeroSrcAdrPkts
long
sdpBndMldSnpgRxZeroSrc
AdrPkts
The value of the object
sdpBndMldSnpgRxZeroSrcAdrPkts
indicates the number of MLD packets
dropped on this SDP Bind because they
contain a zero source IPv6 address.
sdpBndMldSnpgSendQueryCfgDrops
long
sdpBndMldSnpgSendQuer
yCfgDrops
The value of the object
sdpBndMldSnpgSendQueryCfgDrops
indicates the number of times an MLD
Query is dropped because the object
sdpBndMldSnpgCfgSendQueries for this
SDP Bind is set to 'inService(2)'.
SdpBindingMldSnpgStats
MIB table name: TIMETRA-MLD-SNOOPING-MIB.sdpBindMldSnpgStatsTable
Monitored class: vpls.SdpBindingMldSnpgCfg
(12 of 15)
E-176
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBndMldSnpgFwdGenQueries
long
sdpBndMldSnpgFwdGenQ
ueries
The value of the object
sdpBndMldSnpgFwdGenQueries indicates
the number of MLD General Queries
forwarded on this SDP Bind.
sdpBndMldSnpgFwdGrpSpecQuerie
s
long
sdpBndMldSnpgFwdGrpSp
ecQueries
The value of the object
sdpBndMldSnpgFwdGrpSpecQueries
indicates the number of MLD
Group-Specific Queries forwarded on this
SDP Bind.
sdpBndMldSnpgFwdSrcSpecQueries
long
sdpBndMldSnpgFwdSrcSp
ecQueries
The value of the object
sdpBndMldSnpgFwdSrcSpecQueries
indicates the number of MLD
Group-And-Source-Specific Queries
forwarded on this SDP Bind.
sdpBndMldSnpgFwdUnknownType
long
sdpBndMldSnpgFwdUnkno
wnType
The value of the object
sdpBndMldSnpgFwdUnknownType
indicates the number of MLD unknown
type packets forwarded on this SDP Bind.
sdpBndMldSnpgFwdV1Leaves
long
sdpBndMldSnpgFwdV1Lea
ves
The value of the object
sdpBndMldSnpgFwdV1Leaves indicates
the number of MLDv1 Leaves forwarded
on this SDP Bind.
sdpBndMldSnpgFwdV1Reports
long
sdpBndMldSnpgFwdV1Rep
orts
The value of the object
sdpBndMldSnpgFwdV1Reports indicates
the number of MLDv1 Reports forwarded
on this SDP Bind.
sdpBndMldSnpgFwdV2Reports
long
sdpBndMldSnpgFwdV2Rep
orts
The value of the object
sdpBndMldSnpgFwdV2Reports indicates
the number of MLDv2 Reports forwarded
on this SDP Bind.
sdpBndMldSnpgRxGenQueries
long
sdpBndMldSnpgRxGenQue
ries
The value of the object
sdpBndMldSnpgRxGenQueries indicates
the number of MLD General Queries
received on this SDP Bind.
sdpBndMldSnpgRxGrpSpecQueries
long
sdpBndMldSnpgRxGrpSpe
cQueries
The value of the object
sdpBndMldSnpgRxGrpSpecQueries
indicates the number of MLD
Group-Specific Queries received on this
SDP Bind.
sdpBndMldSnpgRxSrcSpecQueries
long
sdpBndMldSnpgRxSrcSpec
Queries
The value of the object
sdpBndMldSnpgRxSrcSpecQueries
indicates the number of MLD
Group-And-Source-Specific Queries
received on this SDP Bind.
sdpBndMldSnpgRxUnknownType
long
sdpBndMldSnpgRxUnknow
nType
The value of the object
sdpBndMldSnpgRxUnknownType indicates
the number of MLD unknown type packets
received on this SDP Bind.
sdpBndMldSnpgRxV1Leaves
long
sdpBndMldSnpgRxV1Leav
es
The value of the object
sdpBndMldSnpgRxV1Leaves indicates the
number of MLDv1 Leaves received on this
SDP Bind.
sdpBndMldSnpgRxV1Reports
long
sdpBndMldSnpgRxV1Repo
rts
The value of the object
sdpBndMldSnpgRxV1Reports indicates the
number of MLDv1 Reports received on this
SDP Bind.
(13 of 15)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-177
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sdpBndMldSnpgRxV2Reports
long
sdpBndMldSnpgRxV2Repo
rts
The value of the object
sdpBndMldSnpgRxV2Reports indicates the
number of MLDv2 Reports received on this
SDP Bind.
sdpBndMldSnpgTxGenQueries
long
sdpBndMldSnpgTxGenQue
ries
The value of the object
sdpBndMldSnpgTxGenQueries indicates
the number of MLD General Queries
transmitted on this SDP Bind.
sdpBndMldSnpgTxGrpSpecQueries
long
sdpBndMldSnpgTxGrpSpe
cQueries
The value of the object
sdpBndMldSnpgTxGrpSpecQueries
indicates the number of MLD
Group-Specific Queries transmitted on
this SDP Bind.
sdpBndMldSnpgTxSrcSpecQueries
long
sdpBndMldSnpgTxSrcSpec
Queries
The value of the object
sdpBndMldSnpgTxSrcSpecQueries
indicates the number of MLD
Group-And-Source-Specific Queries
transmitted on this SDP Bind.
sdpBndMldSnpgTxV1Leaves
long
sdpBndMldSnpgTxV1Leav
es
The value of the object
sdpBndMldSnpgTxV1Leaves indicates the
number of MLDv1 Leaves transmitted on
this SDP Bind.
sdpBndMldSnpgTxV1Reports
long
sdpBndMldSnpgTxV1Repo
rts
The value of the object
sdpBndMldSnpgTxV1Reports indicates the
number of MLDv1 Reports transmitted on
this SDP Bind.
sdpBndMldSnpgTxV2Reports
long
sdpBndMldSnpgTxV2Repo
rts
The value of the object
sdpBndMldSnpgTxV2Reports indicates the
number of MLDv2 Reports transmitted on
this SDP Bind.
SitePimSnoopingStats
MIB table name: TIMETRA-PIM-SNOOPING-MIB.tmnxPimSnpgGenStatsTable
Monitored class: vpls.SitePimSnooping
numSGTypes
long
tmnxPimSnpgGenStatsSG
Types
The value of
tmnxPimSnpgGenStatsSGTypes indicates
the number of entries in
tmnxPimSnpgGrpSrcTable for which the
source type is 'sg'.
numStarGTypes
long
tmnxPimSnpgGenStatsSta
rGTypes
The value of
tmnxPimSnpgGenStatsStarGTypes
indicates the number of entries in
tmnxPimSnpgGrpSrcTable for which the
source type is 'starG'.
SiteSourceGroupRecordPimSnoopingStats
MIB table name: TIMETRA-PIM-SNOOPING-MIB.tmnxPimSnpgGrpSrcStatsTable
Monitored classes:
vpls.SiteSourceGroupRecord
vpls.SitePimSnooping
•
•
(14 of 15)
E-178
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
tmnxPimSnpgGrpSrcStatsFwdedOc
t
long
tmnxPimSnpgGrpSrcStats
FwdedOct
The value of
tmnxPimSnpgGrpSrcStatsFwdedOct
indicates the number of multicast octets
that were forwarded to the interfaces in
the outgoing interface list.
tmnxPimSnpgGrpSrcIfTable lists all the
interfaces in the outgoing interface list.
tmnxPimSnpgGrpSrcStatsFwdedPkt
s
long
tmnxPimSnpgGrpSrcStats
FwdedPkts
The value of
tmnxPimSnpgGrpSrcStatsFwdedPkts
indicates the number of multicast packets
that were forwarded to the interfaces in
the outgoing interface list.
tmnxPimSnpgGrpSrcIfTable lists all the
interfaces in the outgoing interface list.
(15 of 15)
Table E-35 vrrp statistics
5620 SAM counter name
Type
MIB counter name
Description
InstanceAdditionalStats
MIB table name: TIMETRA-VRRP-MIB.tmnxVrrpRouterStatsTable
Monitored class: vrrp.Instance
addressListDiscards
long
tmnxVrrpStatsAddressList
Discards
The total number of VRRP advertisement
packets discarded because the address
list did not match the locally configured
list for the virtual router.
advertiseIntervalDiscards
long
tmnxVrrpStatsAdvertiseIn
tervalDiscards
The total number of VRRP advertisement
packets discarded because the
advertisement interval in the received
packet was different than the one
configured for the local virtual router.
advertiseSent
long
tmnxVrrpStatsAdvertiseS
ent
The total number of VRRP advertisements
sent by this virtual router.
masterChanges
long
tmnxVrrpStatsMasterCha
nges
The value for
tmnxVrrpStatsMasterChanges specifies
the total number of times the virtual
router has seen the master virtual router
change.
preemptedEvents
long
tmnxVrrpStatsPreempted
Events
The value for
tmnxVrrpStatsPreemptedEvents specifies
the total number of times the virtual
router has been preempted by another
non-owner master with higher priority.
preemptEvents
long
tmnxVrrpStatsPreemptEv
ents
The value for
tmnxVrrpStatsPreemptEvents specifies
the total number of times the virtual
router has preempted another non-owner
master with lower priority.
totalDiscards
long
tmnxVrrpStatsTotalDiscar
ds
The total number of VRRP advertisement
packets discarded for any reason. This
includes the packets discarded due to
advertise interval mismatch and address
list mismatch.
(1 of 2)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
E-179
E. 7450 ESS Release 7.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
InstanceStats
MIB table name: VRRP-MIB.vrrpRouterStatsTable
Monitored class: vrrp.Instance
addressListErrors
long
vrrpStatsAddressListError
s
The total number of packets received for
which the address list does not match the
locally configured list for the virtual
router.
advertiseIntervalErrors
long
vrrpStatsAdvertiseInterva
lErrors
The total number of VRRP advertisement
packets received for which the
advertisement interval is different than
the one configured for the local virtual
router.
advertiseRcvd
long
vrrpStatsAdvertiseRcvd
The total number of VRRP advertisements
received by this virtual router.
authFailures
long
vrrpStatsAuthFailures
The total number of VRRP packets
received that do not pass the
authentication check.
authTypeMismatch
long
vrrpStatsAuthTypeMismat
ch
The total number of packets received
with 'Auth Type' not equal to the locally
configured authentication method
(`vrrpOperAuthType').
becomeMaster
long
vrrpStatsBecomeMaster
The total number of times that this virtual
router's state has transitioned to MASTER.
invalidAuthType
long
vrrpStatsInvalidAuthType
The total number of packets received
with an unknown authentication type.
invalidTypePktsRcvd
long
vrrpStatsInvalidTypePkts
Rcvd
The number of VRRP packets received by
the virtual router with an invalid value in
the 'type' field.
ipTtlErrors
long
vrrpStatsIpTtlErrors
The total number of VRRP packets
received by the virtual router with IP TTL
(Time-To-Live) not equal to 255.
packetLengthErrors
long
vrrpStatsPacketLengthErr
ors
The total number of packets received
with a packet length less than the length
of the VRRP header.
priorityZeroPktsRcvd
long
vrrpStatsPriorityZeroPkts
Rcvd
The total number of VRRP packets
received by the virtual router with a
priority of '0'.
priorityZeroPktsSent
long
vrrpStatsPriorityZeroPkts
Sent
The total number of VRRP packets sent by
the virtual router with a priority of '0'.
(2 of 2)
E-180
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F.
7701 CPAA Release 3.0 statistics
counters
F.1 7701 CPAA Release 3.0 statistics counters
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-2
F-1
F. 7701 CPAA Release 3.0 statistics counters
F.1
7701 CPAA Release 3.0 statistics counters
This appendix lists in tabular form the statistics counters that the 5620 SAM supports
for the 7701 CPAA, Release 3.0. Each 5620 SAM counter entry in a table contains
the name and description of the corresponding device MIB counter.
The 5620 SAM counter name in a table entry is the internal counter identifier that is
required for statistics retrieval through the 5620 SAM OSSI. The displayed counter
name in the 5620 SAM GUI is typically an expansion of this identifier. For example,
the receivedBroadcastPackets counter name in the equipment table corresponds to
the Received Broadcast Packets counter name on the Log Record form for an
Ethernet port.
Note 1 — The tables list the 5620 SAM-supported statistics counters
for the current release of the device. Counters that are supported for a
previous device release, but not for the current release, are not listed.
Note 2 — A statistics counter in the 5620 SAM GUI whose displayed
name ends with “Periodic” is a counter that records the difference
between the current and previous values of an associated 5620 SAM
counter. The OSS equivalent name for a Periodic counter is the name
of the 5620 SAM counter with a “Periodic” suffix. The tables in this
appendix do not list Periodic counters.
Table F-1 lists each statistics package and the associated statistics-counter table.
Table F-1 Statistics packages and counter tables
Package name
See
aclfilter
Table F-2
bgp
Table F-3
equipment
Table F-4
ethernetequipment
Table F-5
isis
Table F-6
ospf
Table F-7
rtr
Table F-8
sitesec
Table F-9
Table F-2 aclfilter statistics
5620 SAM counter name
Type
MIB counter name
Description
HitCountStats
MIB table name: TIMETRA-FILTER-MIB.tIPFilterParamsTable
Monitored class: aclfilter.IpFilterEntry
egressHitCount
UINT128
tIPFilterParamsEgressHit
Count
This object indicates the number of times
an egress packet matched this entry.
(1 of 2)
F-2
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
ingressHitCount
UINT128
tIPFilterParamsIngressHit
Count
This object indicates the number of times
an ingress packet matched this entry.
MacHitCountStats
MIB table name: TIMETRA-FILTER-MIB.tMacFilterParamsTable
Monitored class: aclfilter.MacFilterEntry
egressHitCount
UINT128
tMacFilterParamsEgressHi
tCount
This object indicates the number of times
an egress packet matched this entry.
ingressHitCount
UINT128
tMacFilterParamsIngressH
itCount
This object indicates the number of times
an ingress packet matched this entry.
(2 of 2)
Table F-3 bgp statistics
5620 SAM counter name
Type
MIB counter name
Description
bgpPeerFsmEstablishedTi
me
This timer indicates how long (in seconds)
this peer has been in the Established state
or how long since this peer was last in the
Established state. It is set to zero when a
new peer is configured or the router is
booted.
PeerAdditionalStats
MIB table name: BGP4-MIB.bgpPeerTable
Monitored class: bgp.Peer
fsmEstablishedTime
long
PeerStats
MIB table name: TIMETRA-BGP-MIB.tBgpPeerNgOperTable
Monitored class: bgp.Peer
flaps
long
tBgpPeerNgOperFlaps
tBgpPeerNgOperFlaps indicates the
number of flaps of updates from this peer.
inputQueueMessages
long
tBgpPeerNgOperInputQue
ueMsgs
tBgpPeerNgOperInputQueueMsgs
indicates the number of unprocessed
messages in the queue, from this peer.
lastEvent
long
tBgpPeerNgOperLastEven
t
tBgpPeerNgOperLastEvent indicates the
last BGP event of this peer.
lastRestartTime
long
tBgpPeerNgOperLastRest
artTime
tBgpPeerNgOperLastRestartTime
indicates the last time the peer
attempted restart.
lastState
long
tBgpPeerNgOperLastState
tBgpPeerNgOperLastState indicates the
last BGP state of this peer.
mcastActivePrefixes
long
tBgpPeerNgOperMCastV4
ActivePfxs
The value of
tBgpPeerNgOperMCastV4ActivePfxs
indicates the number of active IPv4
multicast prefixes from this peer.
mcastPrefixesSuppressedByDampi
ng
long
tBgpPeerNgOperMCastV4
SuppPfxDamp
The value of
tBgpPeerNgOperMCastV4SuppPfxDamp
indicates the number of IPv4 multicast
prefixes from this peer, which have been
suppressed by damping.
(1 of 3)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-3
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
mcastReceivedPrefixes
long
tBgpPeerNgOperMCastV4
RecvPfxs
The value of
tBgpPeerNgOperMCastV4RecvPfxs
indicates the number of IPv4 multicast
prefixes received from this peer.
mcastSentPrefixes
long
tBgpPeerNgOperMCastV4
SentPfxs
The value of
tBgpPeerNgOperMCastV4SentPfxs
indicates the number of IPv4 multicast
prefixes transmitted to this peer.
messageOctetsReceived
UINT128
tBgpPeerNgOperMsgOctet
sRcvd
tBgpPeerNgOperMsgOctetsRcvd indicates
the number of octets received from this
peer.
messageOctetsSent
UINT128
tBgpPeerNgOperMsgOctet
sSent
tBgpPeerNgOperMsgOctetsSent indicates
the number of octets transmitted to this
peer.
numberOfRestarts
long
tBgpPeerNgOperNumRest
arts
tBgpPeerNgOperNumRestarts indicates
the number of times the peer has
attempted restart.
outputQueueMessages
long
tBgpPeerNgOperOutputQ
ueueMsgs
tBgpPeerNgOperOutputQueueMsgs
indicates the number of untransmitted
messages in the queue, to this peer.
pathsReceived
long
tBgpPeerNgOperReceived
Paths
tBgpPeerNgOperReceivedPaths indicates
the number of paths received from this
peer.
prefixesActive
long
tBgpPeerNgOperActivePr
efixes
tBgpPeerNgOperActivePrefixes indicates
the number of active IPv4 prefixes from
this peer.
prefixesReceived
long
tBgpPeerNgOperReceived
Prefixes
tBgpPeerNgOperReceivedPrefixes
indicates the number of IPv4 prefixes
received from this peer.
prefixesSent
long
tBgpPeerNgOperSentPrefi
xes
tBgpPeerNgOperSentPrefixes indicates
the number of IPv4 prefixes transmitted
to this peer.
prefixesSuppressedByDamping
long
tBgpPeerNgOperV4SuppPf
xDamp
The value of
tBgpPeerNgOperV4SuppPfxDamp
indicates the number of IPv6 prefixes
from this peer, which have been
suppressed by damping.
v6ActivePrefixes
long
tBgpPeerNgOperV6Active
Prefixes
The value of
tBgpPeerNgOperV6ActivePrefixes
indicates the number of active IPv6
prefixes from this peer.
v6PrefixesSuppressedByDamping
long
tBgpPeerNgOperV6SuppPf
xDamp
The value of
tBgpPeerNgOperV6SuppPfxDamp
indicates the number of IPv6 prefixes
from this peer, which have been
suppressed by damping.
v6ReceivedPrefixes
long
tBgpPeerNgOperV6Receiv
edPrefixes
The value of
tBgpPeerNgOperV6ReceivedPrefixes
indicates the number of IPv6 prefixes
received from this peer.
v6SentPrefixes
long
tBgpPeerNgOperV6SentPr
efixes
The value of
tBgpPeerNgOperV6SentPrefixes indicates
the number of IPv6 prefixes transmitted
to this peer.
(2 of 3)
F-4
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
vpnActivePrefixes
long
tBgpPeerNgOperVpnActiv
ePrefixes
tBgpPeerNgOperVpnActivePrefixes
indicates the number of active VPN IPv4
prefixes from this BGP peer.
vpnPrefixesSuppressedByDamping
long
tBgpPeerNgOperVpnSupp
PfxDamp
The value of
tBgpPeerNgOperVpnSuppPfxDamp
indicates the number of VPN IPv4 prefixes
from this peer, which have been
suppressed by damping.
vpnReceivedPrefixes
long
tBgpPeerNgOperVpnRecv
Prefixes
tBgpPeerNgOperVpnRecvPrefixes
indicates the number of received VPN
IPv4 prefixes.
vpnSentPrefixes
long
tBgpPeerNgOperVpnSent
Prefixes
tBgpPeerNgOperVpnSentPrefixes
indicates the number of transmitted VPN
IPv4 prefixes.
(3 of 3)
Table F-4 equipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AllocatedMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryPoolAllocated
Monitored class: equipment.SystemStatsHolder
allocatedMemory
long
sgiMemoryPoolAllocated
The value of sgiMemoryPoolAllocated
indicates the total memory currently
allocated in memory-pools on the system.
This memory may or may not be currently
in use, but is pre-allocated should the
software need to use it.
AvailableMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryAvailable
Monitored class: equipment.SystemStatsHolder
availableMemory
long
sgiMemoryAvailable
The value of sgiMemoryAvailable
indicates the amount of free memory in
the overall system that is not allocated to
memory pools, but is available in case a
memory pool needs to grow.
CiscoHDLCStats
MIB table name: TIMETRA-PORT-MIB.tmnxCiscoHDLCStatsTable
Monitored classes:
• tdmequipment.DS3E3Channel
• tdmequipment.DS0ChannelGroup
discardStatInPkts
long
tmnxCiscoHDLCDiscardSt
atInPkts
tmnxCiscoHDLCDiscardStatInPkts
indicates the number of inbound Cisco
HDLC packets discarded.
discardStatOutPkts
long
tmnxCiscoHDLCDiscardSt
atOutPkts
tmnxCiscoHDLCDiscardStatOutPkts
indicates the number of outbound Cisco
HDLC packets discarded.
statInOctets
long
tmnxCiscoHDLCStatInOct
ets
tmnxCiscoHDLCStatInOctets indicates the
number of inbound Cisco HDLC octets.
(1 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-5
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
statInPkts
long
tmnxCiscoHDLCStatInPkts
tmnxCiscoHDLCStatInPkts indicates the
number of inbound Cisco HDLC packets.
statOutOctets
long
tmnxCiscoHDLCStatOutOc
tets
tmnxCiscoHDLCStatOutOctets indicates
the number of outbound Cisco HDLC
octets.
statOutPkts
long
tmnxCiscoHDLCStatOutPk
ts
tmnxCiscoHDLCStatOutPkts indicates the
number of outbound Cisco HDLC packets.
InterfaceAdditionalStats
MIB table name: IF-MIB.ifXTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
receivedBroadcastPackets
UINT128
ifHCInBroadcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a broadcast address at
this sub-layer. This object is a 64-bit
version of ifInBroadcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedMulticastPackets
UINT128
ifHCInMulticastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were addressed to a multicast address at
this sub-layer. For a MAC layer protocol,
this includes both Group and Functional
addresses. This object is a 64-bit version
of ifInMulticastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedTotalOctets
UINT128
ifHCInOctets
The total number of octets received on
the interface, including framing
characters. This object is a 64-bit version
of ifInOctets. Discontinuities in the value
of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedUnicastPackets
UINT128
ifHCInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer. This
object is a 64-bit version of ifInUcastPkts.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
(2 of 7)
F-6
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmittedBroadcastPackets
UINT128
ifHCOutBroadcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a broadcast address at this sub-layer,
including those that were discarded or not
sent. This object is a 64-bit version of
ifOutBroadcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedMulticastPackets
UINT128
ifHCOutMulticastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were addressed to
a multicast address at this sub-layer,
including those that were discarded or not
sent. For a MAC layer protocol, this
includes both Group and Functional
addresses. This object is a 64-bit version
of ifOutMulticastPkts. Discontinuities in
the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedTotalOctets
UINT128
ifHCOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. This object is a 64-bit version
of ifOutOctets. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
transmittedUnicastPackets
UINT128
ifHCOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent. This
object is a 64-bit version of
ifOutUcastPkts. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
InterfaceStats
MIB table name: IF-MIB.ifTable
Monitored classes: equipment.PhysicalPort; equipment.ManagementPort; lag.Interface; bundle.Interface;
sonetequipment.Sts1Channel; sonetequipment.Sts3Channel; sonetequipment.Sts12Channel;
sonetequipment.Sts48Channel; sonetequipment.Sts192Channel; tdmequipment.DS3E3Channel;
tdmequipment.DS1E1Channel; tdmequipment.DS0ChannelGroup; ccag.CcagPathCcNetSap; ccag.CcagPathCcSapNet;
ccag.CcagPathCcSapSap; sonetequipment.Tu3Channel; sonetequipment.TributaryChannel
(3 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-7
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
outboundBadPackets
long
ifOutErrors
For packet-oriented interfaces, the
number of outbound packets that could
not be transmitted because of errors. For
character-oriented or fixed-length
interfaces, the number of outbound
transmission units that could not be
transmitted because of errors.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
outboundPacketsDiscarded
long
ifOutDiscards
The number of outbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being transmitted. One possible
reason for discarding such a packet could
be to free up buffer space. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
receivedBadPackets
long
ifInErrors
For packet-oriented interfaces, the
number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol. For character- oriented or
fixed-length interfaces, the number of
inbound transmission units that contained
errors preventing them from being
deliverable to a higher-layer protocol.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedOctets
long
ifInOctets
The total number of octets received on
the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
receivedPacketsDiscarded
long
ifInDiscards
The number of inbound packets which
were chosen to be discarded even though
no errors had been detected to prevent
their being deliverable to a higher-layer
protocol. One possible reason for
discarding such a packet could be to free
up buffer space. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
(4 of 7)
F-8
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
receivedUnicastPackets
long
ifInUcastPkts
The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
receivedUnknownProtocolPackets
long
ifInUnknownProtos
For packet-oriented interfaces, the
number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
For character-oriented or fixed-length
interfaces that support protocol
multiplexing the number of transmission
units received via the interface which
were discarded because of an unknown or
unsupported protocol. For any interface
that does not support protocol
multiplexing, this counter will always be
0. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedOctets
long
ifOutOctets
The total number of octets transmitted
out of the interface, including framing
characters. Discontinuities in the value of
this counter can occur at re-initialization
of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime.
transmittedUnicastPackets
long
ifOutUcastPkts
The total number of packets that
higher-level protocols requested be
transmitted, and which were not
addressed to a multicast or broadcast
address at this sub-layer, including those
that were discarded or not sent.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime.
MediaIndependentStats
MIB table name: HC-RMON-MIB.mediaIndependentTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
dropEvents
long
mediaIndependentDropEv
ents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
(5 of 7)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-9
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
droppedFrames
long
mediaIndependentDropp
edFrames
The total number of frames which were
received by the probe and therefore not
accounted for in the
mediaIndependentDropEvents, but for
which the probe chose not to count for
this entry for whatever reason. Most
often, this event occurs when the probe is
out of some resources and decides to shed
load from this collection. This count does
not include packets that were not
counted because they had MAC-layer
errors. Note that, unlike the dropEvents
counter, this number is the exact number
of frames dropped.
duplex
int
mediaIndependentDuplex
Mode
The current mode of this link. Note that if
the link has full-duplex capabilities but is
operating in half-duplex mode, this value
will be halfduplex(1).
duplexChanges
long
mediaIndependentDuplex
Changes
The number of times this link has changed
from full-duplex mode to half-duplex
mode or from half-duplex mode to
full-duplex mode.
inputSpeed
long
mediaIndependentInputS
peed
The nominal maximum speed in kilobits
per second of this half-duplex link or on
the inbound connection of this full-duplex
link. If the speed is unknown or there is no
fixed maximum (e.g. a compressed link),
this value shall be zero.
outputSpeed
long
mediaIndependentOutput
Speed
The nominal maximum speed in kilobits
per second of this full-duplex link in the
direction of the network. If the speed is
unknown, the link is half-duplex, or there
is no fixed maximum (e.g. a compressed
link), this value shall be zero.
receivedBadPackets
long
mediaIndependentInError
s
The total number of bad packets received
on a half-duplex link or on the inbound
connection of a full-duplex link.
receivedNonUnicastPackets
UINT128
mediaIndependentInNUC
astHighCapacityPkts
The total number of non-unicast packets
(including bad packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
receivedOctets
UINT128
mediaIndependentInHigh
CapacityOctets
The total number of octets of data
(including those in bad packets) received
(excluding framing bits but including FCS
octets) on a half-duplex link or on the
inbound connection of a full-duplex link.
receivedPackets
UINT128
mediaIndependentInHigh
CapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
half-duplex link or on the inbound
connection of a full-duplex link.
transmittedBadPackets
long
mediaIndependentOutErr
ors
The total number of bad packets received
on a full-duplex link in the direction of the
network.
transmittedNonUnicastPackets
UINT128
mediaIndependentOutNU
CastHighCapacityPkts
The total number of packets (including
bad packets) received on a full-duplex
link in the direction of the network.
(6 of 7)
F-10
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
transmittedOctets
UINT128
mediaIndependentOutHig
hCapacityOctets
The total number of octets of data
(including those in bad packets) received
on a full-duplex link in the direction of the
network (excluding framing bits but
including FCS octets).
transmittedPackets
UINT128
mediaIndependentOutHig
hCapacityPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received on a
full-duplex link in the direction of the
network.
SystemCpuStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiCpuUsage
Monitored class: equipment.SystemStatsHolder
systemCpuUsage
long
sgiCpuUsage
The value of sgiCpuUsage indicates the
current CPU utilization for the system.
SystemMemoryStats
MIB table name: TIMETRA-SYSTEM-MIB.sgiMemoryUsed
Monitored class: equipment.SystemStatsHolder
systemMemoryUsage
long
sgiMemoryUsed
The value of sgiMemoryUsed indicates the
total pre-allocated pool memory
currently in use on the system.
(7 of 7)
Table F-5 ethernetequipment statistics
5620 SAM counter name
Type
MIB counter name
Description
AdditionalEthernetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortEtherTable
Monitored classes:
•
•
equipment.PhysicalPort
equipment.ManagementPort
highCapacityPackets1519toMaxFra
meSize
UINT128
tmnxPortEtherHCPkts151
9toMax
The total number of packets (including
bad packets) received that were between
1519 octets in length and the maximum
frame size, usually 12287 octets inclusive
(excluding framing bits but including FCS
octets). The lower 32-bits of this 64-bit
counter will equal the value of
tmnxPortEtherHCPkts1519toMax. The
high 32-bits of this counter will equal the
value of
tmnxPortEtherHCOverPkts1519toMax.
packets1519toMaxFrameSize
long
tmnxPortEtherPkts1519to
Max
The total number of packets received that
were longer than 1518 octets but less than
the maximum frame size for the
particular medium, usually 12287 octets
(excluding framing bits, but including FCS
octets) and were otherwise well formed.
Dot3Stats
MIB table name: EtherLike-MIB.dot3StatsTable
Monitored class: equipment.PhysicalPort
(1 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-11
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
alignmentErrors
long
dot3StatsAlignmentErrors
A count of frames received on a particular
interface that are not an integral number
of octets in length and do not pass the FCS
check. The count represented by an
instance of this object is incremented
when the alignmentError status is
returned by the MAC service to the LLC (or
other MAC user). Received frames for
which multiple error conditions pertain
are, according to the conventions of IEEE
802.3 Layer Management, counted
exclusively according to the error status
presented to the LLC. This counter does
not increment for group encoding
schemes greater than 4 bits per group. For
interfaces operating at 10 Gb/s, this
counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsAlignmentErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.1.1.7,
aAlignmentErrors.
carrierSenseErrors
long
dot3StatsCarrierSenseErr
ors
The number of times that the carrier
sense condition was lost or never asserted
when attempting to transmit a frame on a
particular interface. The count
represented by an instance of this object
is incremented at most once per
transmission attempt, even if the carrier
sense condition fluctuates during a
transmission attempt. This counter does
not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.13,
aCarrierSenseErrors.
(2 of 16)
F-12
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
deferredTransmissions
long
dot3StatsDeferredTransm
issions
A count of frames for which the first
transmission attempt on a particular
interface is delayed because the medium
is busy. The count represented by an
instance of this object does not include
frames involved in collisions. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.9,
aFramesWithDeferredXmissions.
duplex
int
dot3StatsDuplexStatus
The current mode of operation of the MAC
entity. 'unknown' indicates that the
current duplex mode could not be
determined. Management control of the
duplex mode is accomplished through the
MAU MIB. When an interface does not
support autonegotiation, or when
autonegotiation is not enabled, the
duplex mode is controlled using
ifMauDefaultType. When autonegotiation
is supported and enabled, duplex mode is
controlled using
ifMauAutoNegAdvertisedBits. In either
case, the currently operating duplex
mode is reflected both in this object and
in ifMauType. Note that this object
provides redundant information with
ifMauType. Normally, redundant objects
are discouraged. However, in this
instance, it allows a management
application to determine the duplex
status of an interface without having to
know every possible value of ifMauType.
This was felt to be sufficiently valuable to
justify the redundancy. REFERENCE [IEEE
802.3 Std.], 30.3.1.1.32, aDuplexStatus.
excessiveCollisions
long
dot3StatsExcessiveCollisi
ons
A count of frames for which transmission
on a particular interface fails due to
excessive collisions. This counter does not
increment when the interface is operating
in full-duplex mode. Discontinuities in the
value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.11,
aFramesAbortedDueToXSColls.
(3 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-13
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
fcsErrors
long
dot3StatsFCSErrors
A count of frames received on a particular
interface that are an integral number of
octets in length but do not pass the FCS
check. This count does not include frames
received with frame-too-long or
frame-too-short error. The count
represented by an instance of this object
is incremented when the
frameCheckError status is returned by the
MAC service to the LLC (or other MAC
user). Received frames for which multiple
error conditions pertain are, according to
the conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. Note: Coding errors detected by
the physical layer for speeds above 10
Mb/s will cause the frame to fail the FCS
check. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 5 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the dot3HCStatsFCSErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.6,
aFrameCheckSequenceErrors.
frameTooLongs
long
dot3StatsFrameTooLongs
A count of frames received on a particular
interface that exceed the maximum
permitted frame size. The count
represented by an instance of this object
is incremented when the frameTooLong
status is returned by the MAC service to
the LLC (or other MAC user). Received
frames for which multiple error
conditions pertain are, according to the
conventions of IEEE 802.3 Layer
Management, counted exclusively
according to the error status presented to
the LLC. For interfaces operating at 10
Gb/s, this counter can roll over in less
than 80 minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsFrameTooLongs object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.],
30.3.1.1.25, aFrameTooLongErrors.
(4 of 16)
F-14
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
internalMacReceiveErrors
long
dot3StatsInternalMacRec
eiveErrors
A count of frames for which reception on
a particular interface fails due to an
internal MAC sublayer receive error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsFrameTooLongs object, the
dot3StatsAlignmentErrors object, or the
dot3StatsFCSErrors object. The precise
meaning of the count represented by an
instance of this object is implementationspecific. In particular, an instance of this
object may represent a count of receive
errors on a particular interface that are
not otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacReceiveErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.15,
aFramesLostDueToIntMACRcvError.
internalMacTransmitErrors
long
dot3StatsInternalMacTran
smitErrors
A count of frames for which transmission
on a particular interface fails due to an
internal MAC sublayer transmit error. A
frame is only counted by an instance of
this object if it is not counted by the
corresponding instance of either the
dot3StatsLateCollisions object, the
dot3StatsExcessiveCollisions object, or
the dot3StatsCarrierSenseErrors object.
The precise meaning of the count
represented by an instance of this object
is implementation- specific. In particular,
an instance of this object may represent a
count of transmission errors on a
particular interface that are not
otherwise counted. For interfaces
operating at 10 Gb/s, this counter can roll
over in less than 5 minutes if it is
incrementing at its maximum rate. Since
that amount of time could be less than a
management station's poll cycle time, in
order to avoid a loss of information, a
management station is advised to poll the
dot3HCStatsInternalMacTransmitErrors
object for 10 Gb/s or faster interfaces.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.12,
aFramesLostDueToIntMACXmitError.
(5 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-15
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
lateCollisions
long
dot3StatsLateCollisions
The number of times that a collision is
detected on a particular interface later
than one slotTime into the transmission of
a packet. A (late) collision included in a
count represented by an instance of this
object is also considered as a (generic)
collision for purposes of other
collision-related statistics. This counter
does not increment when the interface is
operating in full-duplex mode.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times
as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.10,
aLateCollisions.
multipleCollisionFrames
long
dot3StatsMultipleCollisio
nFrames
A count of frames that are involved in
more than one collision and are
subsequently transmitted successfully. A
frame that is counted by an instance of
this object is also counted by the
corresponding instance of either the
ifOutUcastPkts, ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsSingleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.4,
aMultipleCollisionFrames.
singleCollisionFrames
long
dot3StatsSingleCollisionF
rames
A count of frames that are involved in a
single collision, and are subsequently
transmitted successfully. A frame that is
counted by an instance of this object is
also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or
ifOutBroadcastPkts, and is not counted by
the corresponding instance of the
dot3StatsMultipleCollisionFrames object.
This counter does not increment when the
interface is operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 30.3.1.1.3,
aSingleCollisionFrames.
(6 of 16)
F-16
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
sqeTestErrors
long
dot3StatsSQETestErrors
A count of times that the SQE TEST ERROR
is received on a particular interface. The
SQE TEST ERROR is set in accordance with
the rules for verification of the SQE
detection mechanism in the PLS Carrier
Sense Function as described in IEEE Std.
802.3, 2000 Edition, section 7.2.4.6. This
counter does not increment on interfaces
operating at speeds greater than 10 Mb/s,
or on interfaces operating in full-duplex
mode. Discontinuities in the value of this
counter can occur at re-initialization of
the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime. REFERENCE
[IEEE 802.3 Std.], 7.2.4.6, also
30.3.2.1.4, aSQETestErrors.
(7 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-17
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
symbolErrors
long
dot3StatsSymbolErrors
For an interface operating at 100 Mb/s,
the number of times there was an invalid
data symbol when a valid carrier was
present. For an interface operating in
half-duplex mode at 1000 Mb/s, the
number of times the receiving media is
non-idle (a carrier event) for a period of
time equal to or greater than slotTime,
and during which there was at least one
occurrence of an event that causes the
PHY to indicate 'Data reception error' or
'carrier extend error' on the GMII. For an
interface operating in full-duplex mode at
1000 Mb/s, the number of times the
receiving media is non-idle (a carrier
event) for a period of time equal to or
greater than minFrameSize, and during
which there was at least one occurrence
of an event that causes the PHY to
indicate 'Data reception error' on the
GMII. For an interface operating at 10
Gb/s, the number of times the receiving
media is non-idle (a carrier event) for a
period of time equal to or greater than
minFrameSize, and during which there
was at least one occurrence of an event
that causes the PHY to indicate 'Receive
Error' on the XGMII. The count
represented by an instance of this object
is incremented at most once per carrier
event, even if multiple symbol errors
occur during the carrier event. This count
does not increment if a collision is
present. This counter does not increment
when the interface is operating at 10
Mb/s. For interfaces operating at 10 Gb/s,
this counter can roll over in less than 5
minutes if it is incrementing at its
maximum rate. Since that amount of time
could be less than a management station's
poll cycle time, in order to avoid a loss of
information, a management station is
advised to poll the
dot3HCStatsSymbolErrors object for 10
Gb/s or faster interfaces. Discontinuities
in the value of this counter can occur at
re-initialization of the management
system, and at other times as indicated by
the value of ifCounterDiscontinuityTime.
REFERENCE [IEEE 802.3 Std.], 30.3.2.1.5,
aSymbolErrorDuringCarrier.
EthernetHighCapacityStats
MIB table name: HC-RMON-MIB.etherStatsHighCapacityTable
Monitored classes:
• equipment.PhysicalPort
• equipment.ManagementPort
packets1024to1518Octets
UINT128
etherStatsHighCapacityPk
ts1024to1518Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
(8 of 16)
F-18
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
packets128to255Octets
UINT128
etherStatsHighCapacityPk
ts128to255Octets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
UINT128
etherStatsHighCapacityPk
ts256to511Octets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
UINT128
etherStatsHighCapacityPk
ts512to1023Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
UINT128
etherStatsHighCapacityPk
ts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
UINT128
etherStatsHighCapacityPk
ts65to127Octets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(9 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-19
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
UINT128
etherStatsHighCapacityO
ctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). If the network
is half-duplex Fast Ethernet, this object
can be used as a reasonable estimate of
utilization. If greater precision is desired,
the etherStatsHighCapacityPkts and
etherStatsHighCapacityOctets objects
should be sampled before and after a
common interval. The differences in the
sampled values are Pkts and Octets,
respectively, and the number of seconds
in the interval is Interval. These values
are used to calculate the Utilization as
follows: Pkts * (.96 + .64) + (Octets * .08)
Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent. This table is not
appropriate for monitoring full-duplex
ethernets. If the network is a full-duplex
ethernet and the mediaIndependentTable
is monitoring that network, the utilization
can be calculated as follows: 1)
Determine the utilization of the inbound
path by using the appropriate equation
(for ethernet or fast ethernet) to
determine the utilization, substituting
mediaIndependentInPkts for
etherStatsHighCapacityPkts, and
mediaIndependentInOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization inUtilization. 2)
Determine the utilization of the outbound
path by using the same equation to
determine the utilization, substituting
mediaIndependentOutPkts for
etherStatsHighCapacityPkts, and
mediaIndependentOutOctets for
etherStatsHighCapacityOctets. Call the
resulting utilization outUtilization. 3) The
utilization is the maximum of inUtilization
and outUtilization. This metric shows the
amount of percentage of bandwidth that
is left before congestion will be
experienced on the link.
totalPackets
UINT128
etherStatsHighCapacityPk
ts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
etherStatsBroadcastPkts
The total number of good packets
received that were directed to the
broadcast address. Note that this does not
include multicast packets.
EthernetStats
MIB table name: RMON-MIB.etherStatsTable
Monitored classes:
equipment.PhysicalPort
equipment.ManagementPort
•
•
broadcastPackets
long
(10 of 16)
F-20
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
collisions
long
etherStatsCollisions
The best estimate of the total number of
collisions on this Ethernet segment. The
value returned will depend on the
location of the RMON probe. Section
8.2.1.3 (10BASE-5) and section 10.3.1.3
(10BASE-2) of IEEE standard 802.3 states
that a station must detect a collision, in
the receive mode, if three or more
stations are transmitting simultaneously.
A repeater port must detect a collision
when two or more stations are
transmitting simultaneously. Thus a probe
placed on a repeater port could record
more collisions than a probe connected to
a station on the same segment would.
Probe location plays a much smaller role
when considering 10BASE-T. 14.2.1.4
(10BASE-T) of IEEE standard 802.3 defines
a collision as the simultaneous presence
of signals on the DO and RD circuits
(transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus
probes placed on a station and a repeater,
should report the same number of
collisions. Note also that an RMON probe
inside a repeater should ideally report
collisions between the repeater and one
or more other hosts (transmit collisions as
defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments
to which the repeater is connected.
crcAlignErrors
long
etherStatsCRCAlignErrors
The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and
1518 octets, inclusive, but had either a
bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a
bad FCS with a non-integral number of
octets (Alignment Error).
dropEvents
long
etherStatsDropEvents
The total number of events in which
packets were dropped by the probe due to
lack of resources. Note that this number is
not necessarily the number of packets
dropped; it is just the number of times
this condition has been detected.
fragments
long
etherStatsFragments
The total number of packets received that
were less than 64 octets in length
(excluding framing bits but including FCS
octets) and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that it is entirely normal for
etherStatsFragments to increment. This is
because it counts both runts (which are
normal occurrences due to collisions) and
noise hits.
(11 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-21
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
jabbers
long
etherStatsJabbers
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets),
and had either a bad Frame Check
Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment
Error). Note that this definition of jabber
is different than the definition in
IEEE-802.3 section 8.2.1.5 (10BASE5) and
section 10.3.1.4 (10BASE2). These
documents define jabber as the condition
where any packet exceeds 20 ms. The
allowed range to detect jabber is
between 20 ms and 150 ms.
multicastPackets
long
etherStatsMulticastPkts
The total number of good packets
received that were directed to a
multicast address. Note that this number
does not include packets directed to the
broadcast address.
oversizePackets
long
etherStatsOversizePkts
The total number of packets received that
were longer than 1518 octets (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
packets1024to1518Octets
long
etherStatsPkts1024to151
8Octets
The total number of packets (including
bad packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets128to255Octets
long
etherStatsPkts128to255O
ctets
The total number of packets (including
bad packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets256to511Octets
long
etherStatsPkts256to511O
ctets
The total number of packets (including
bad packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets512to1023Octets
long
etherStatsPkts512to1023
Octets
The total number of packets (including
bad packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS
octets).
packets64Octets
long
etherStatsPkts64Octets
The total number of packets (including
bad packets) received that were 64 octets
in length (excluding framing bits but
including FCS octets).
packets65to127Octets
long
etherStatsPkts65to127Oc
tets
The total number of packets (including
bad packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS
octets).
(12 of 16)
F-22
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
totalOctets
long
etherStatsOctets
The total number of octets of data
(including those in bad packets) received
on the network (excluding framing bits
but including FCS octets). This object can
be used as a reasonable estimate of
10-Megabit ethernet utilization. If greater
precision is desired, the etherStatsPkts
and etherStatsOctets objects should be
sampled before and after a common
interval. The differences in the sampled
values are Pkts and Octets, respectively,
and the number of seconds in the interval
is Interval. These values are used to
calculate the Utilization as follows: Pkts *
(9.6 + 6.4) + (Octets * .8) Utilization =
------------------------------------- Interval *
10,000 The result of this equation is the
value Utilization which is the percent
utilization of the ethernet segment on a
scale of 0 to 100 percent.
totalPackets
long
etherStatsPkts
The total number of packets (including
bad packets, broadcast packets, and
multicast packets) received.
undersizePackets
long
etherStatsUndersizePkts
The total number of packets received that
were less than 64 octets long (excluding
framing bits, but including FCS octets)
and were otherwise well formed.
QosDroppedOctetStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngrMdaQosStatTable
Monitored class: equipment.PhysicalPort
qosClassifier0DroppedOctets
UINT128
tmnxPortIngrMdaQos00St
atDropOcts
tmnxPortIngrMdaQos00StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier10DroppedOctets
UINT128
tmnxPortIngrMdaQos10St
atDropOcts
tmnxPortIngrMdaQos10StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier11DroppedOctets
UINT128
tmnxPortIngrMdaQos11St
atDropOcts
tmnxPortIngrMdaQos11StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier12DroppedOctets
UINT128
tmnxPortIngrMdaQos12St
atDropOcts
tmnxPortIngrMdaQos12StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier13DroppedOctets
UINT128
tmnxPortIngrMdaQos13St
atDropOcts
tmnxPortIngrMdaQos13StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(13 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-23
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier14DroppedOctets
UINT128
tmnxPortIngrMdaQos14St
atDropOcts
tmnxPortIngrMdaQos14StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier15DroppedOctets
UINT128
tmnxPortIngrMdaQos15St
atDropOcts
tmnxPortIngrMdaQos15StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier1DroppedOctets
UINT128
tmnxPortIngrMdaQos01St
atDropOcts
tmnxPortIngrMdaQos01StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier2DroppedOctets
UINT128
tmnxPortIngrMdaQos02St
atDropOcts
tmnxPortIngrMdaQos02StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier3DroppedOctets
UINT128
tmnxPortIngrMdaQos03St
atDropOcts
tmnxPortIngrMdaQos03StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier4DroppedOctets
UINT128
tmnxPortIngrMdaQos04St
atDropOcts
tmnxPortIngrMdaQos04StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier5DroppedOctets
UINT128
tmnxPortIngrMdaQos05St
atDropOcts
tmnxPortIngrMdaQos05StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier6DroppedOctets
UINT128
tmnxPortIngrMdaQos06St
atDropOcts
tmnxPortIngrMdaQos06StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier7DroppedOctets
UINT128
tmnxPortIngrMdaQos07St
atDropOcts
tmnxPortIngrMdaQos07StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier8DroppedOctets
UINT128
tmnxPortIngrMdaQos08St
atDropOcts
tmnxPortIngrMdaQos08StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier9DroppedOctets
UINT128
tmnxPortIngrMdaQos09St
atDropOcts
tmnxPortIngrMdaQos09StatDropOcts
indicates the number of octets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(14 of 16)
F-24
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
QosDroppedPacketStats
MIB table name: TIMETRA-PORT-MIB.tmnxPortIngrMdaQosStatTable
Monitored class: equipment.PhysicalPort
qosClassifier0DroppedPackets
UINT128
tmnxPortIngrMdaQos00St
atDropPkts
tmnxPortIngrMdaQos00StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier10DroppedPackets
UINT128
tmnxPortIngrMdaQos10St
atDropPkts
tmnxPortIngrMdaQos10StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier11DroppedPackets
UINT128
tmnxPortIngrMdaQos11St
atDropPkts
tmnxPortIngrMdaQos11StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier12DroppedPackets
UINT128
tmnxPortIngrMdaQos12St
atDropPkts
tmnxPortIngrMdaQos12StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier13DroppedPackets
UINT128
tmnxPortIngrMdaQos13St
atDropPkts
tmnxPortIngrMdaQos13StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier14DroppedPackets
UINT128
tmnxPortIngrMdaQos14St
atDropPkts
tmnxPortIngrMdaQos14StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier15DroppedPackets
UINT128
tmnxPortIngrMdaQos15St
atDropPkts
tmnxPortIngrMdaQos15StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier1DroppedPackets
UINT128
tmnxPortIngrMdaQos01St
atDropPkts
tmnxPortIngrMdaQos01StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier2DroppedPackets
UINT128
tmnxPortIngrMdaQos02St
atDropPkts
tmnxPortIngrMdaQos02StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier3DroppedPackets
UINT128
tmnxPortIngrMdaQos03St
atDropPkts
tmnxPortIngrMdaQos03StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(15 of 16)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-25
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
qosClassifier4DroppedPackets
UINT128
tmnxPortIngrMdaQos04St
atDropPkts
tmnxPortIngrMdaQos04StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier5DroppedPackets
UINT128
tmnxPortIngrMdaQos05St
atDropPkts
tmnxPortIngrMdaQos05StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier6DroppedPackets
UINT128
tmnxPortIngrMdaQos06St
atDropPkts
tmnxPortIngrMdaQos06StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier7DroppedPackets
UINT128
tmnxPortIngrMdaQos07St
atDropPkts
tmnxPortIngrMdaQos07StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier8DroppedPackets
UINT128
tmnxPortIngrMdaQos08St
atDropPkts
tmnxPortIngrMdaQos08StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
qosClassifier9DroppedPackets
UINT128
tmnxPortIngrMdaQos09St
atDropPkts
tmnxPortIngrMdaQos09StatDropPkts
indicates the number of packets dropped
on the oversubscribed MDA for given Qos
classifier result because of an overload
condition on the MDA.
(16 of 16)
Table F-6 isis statistics
5620 SAM counter name
Type
MIB counter name
Description
InterfaceLevelOneReceivingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelOneConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
(1 of 4)
F-26
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
InterfaceLevelOneSendingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelOneConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelTwoReceivingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelTwoConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
InterfaceLevelTwoSendingStats
MIB table name: ISIS-MIB.isisPacketCountTable
Monitored class: isis.InterfaceLevelTwoConfig
cnspCount
long
isisPacketCountCSNP
The number of IS-IS CSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
helloCount
long
isisPacketCountHello
The number of IS-IS Hello PDUs seen in
this direction at this level. REFERENCE
ISIS.aoi iSISControlPDUsSent (43).
lspCount
long
isisPacketCountLSP
The number of IS-IS LSPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
psnpCount
long
isisPacketCountPSNP
The number of IS-IS PSNPs seen in this
direction at this level. REFERENCE ISIS.aoi
iSISControlPDUsSent (43).
LinkStatePduSiteStats
MIB table name: TIMETRA-ISIS-MIB.vRtrIsisStatsTable
Monitored class: isis.Site
(2 of 4)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-27
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
csnpDropped
long
vRtrIsisCSNPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisCSNPDrop.
csnpReceived
long
vRtrIsisCSNPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisCSNPRecd.
csnpRetransmitted
long
vRtrIsisCSNPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisCSNPRetrans.
csnpSent
long
vRtrIsisCSNPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisCSNPSent.
helloDropped
long
vRtrIsisIIHDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisIIHDrop.
helloReceived
long
vRtrIsisIIHRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisIIHRecd.
helloRetransmitted
long
vRtrIsisIIHRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisIIHRetrans.
helloSent
long
vRtrIsisIIHSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisIIHSent.
lspDropped
long
vRtrIsisLSPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisLSPDrop.
lspReceived
long
vRtrIsisLSPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisLSPRecd.
lspRetransmitted
long
vRtrIsisLSPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisLSPRetrans.
lspSent
long
vRtrIsisLSPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisLSPSent.
psnpDropped
long
vRtrIsisPSNPDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisPSNPDrop.
psnpReceived
long
vRtrIsisPSNPRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisPSNPRecd.
psnpRetransmitted
long
vRtrIsisPSNPRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisPSNPRetrans.
psnpSent
long
vRtrIsisPSNPSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisPSNPSent.
(3 of 4)
F-28
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
unknownDropped
long
vRtrIsisUnknownDrop
The count of link state PDUs dropped by
this instance of the protocol is maintained
by vRtrIsisUnknownDrop.
unknownReceived
long
vRtrIsisUnknownRecd
The count of link state PDUs received by
this instance of the protocol is maintained
by vRtrIsisUnknownRecd.
unknownRetransmitted
long
vRtrIsisUnknownRetrans
The count of link state PDUs that had to
be retransmitted by this instance of the
protocol is maintained by
vRtrIsisUnknownRetrans.
unknownSent
long
vRtrIsisUnknownSent
The count of link state PDUs sent out by
this instance of the protocol is maintained
by vRtrIsisUnknownSent.
SiteStats
MIB table name: TIMETRA-ISIS-MIB.vRtrIsisStatsTable
Monitored class: isis.Site
cspfDroppedRequests
long
vRtrIsisCSPFDroppedRequ
ests
vRtrIsisCSPFDroppedRequests maintains
the number of dropped CSPF requests by
the protocol.
cspfPathsFound
long
vRtrIsisCSPFPathsFound
vRtrIsisCSPFPathsFound maintains the
number of responses to CSPF requests for
which paths satisfying the constraints
were found.
cspfPathsNotFound
long
vRtrIsisCSPFPathsNotFoun
d
vRtrIsisCSPFPathsFound maintains the
number of responses to CSPF requests for
which no paths satisfying the constraints
were found.
cspfRequests
long
vRtrIsisCSPFRequests
vRtrIsisCSPFRequests maintains the
number of CSPF requests made to the
protocol.
initiatedPurges
long
vRtrIsisInitiatedPurges
The value of vRtrIsisInitiatedPurges
counts the number of times purges have
been initiated.
lspRegenerations
long
vRtrIsisLSPRegenerations
The value of vRtrIsisLSPRegenerations
maintains the count of LSP regenerations.
spfRuns
long
vRtrIsisSpfRuns
The value of vRtrIsisSpfRuns indicates the
number of times shortest path first
calculations have been made.
(4 of 4)
Table F-7 ospf statistics
5620 SAM counter name
Type
MIB counter name
Description
AreaBasicStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfAreaTable
Monitored class: ospf.AreaSite
(1 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-29
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
nssaTranslatorEvents
long
tmnxOspfAreaNssaTransl
atorEvents
The value of
tmnxOspfAreaNssaTranslatorEvents
indicates the number of Translator State
changes that have occurred since the last
boot-up.
totalLSACount
long
tmnxOspfAreaScopeLsaCo
unt
The value of tmnxOspfAreaScopeLsaCount
indicates the total number of Area-Scope
link state advertisements in this area's
link-state database.
totalSpfRuns
long
tmnxOspfAreaSpfRuns
The value of tmnxOspfAreaSpfRuns
indicates the number of times that the
intra-area route table has been
calculated using this area's link-state
database. This is typically done using
Dijkstra's algorithm.
totalUnknownLSACount
long
tmnxOspfAreaScopeUnkLs
aCount
The value of
tmnxOspfAreaScopeUnkLsaCount
indicates the total number of unknown
Area-Scope link-state advertisements in
this area's link-state database.
InterfaceGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
events
long
tmnxOspfIfEvents
The value of tmnxOspfIfEvents indicates
the number of times this OSPF interface
has changed its state, or an error has
occurred.
InterfaceReceiveStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
databaseDescriptionPackets
long
tmnxOspfIfRxDBDs
The value of tmnxOspfIfRxDBDs indicates
the total number of OSPF Database
Description packets received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
databaseDescriptionPackets
long
tmnxOspfIfTxDBDs
The value of tmnxOspfIfTxDBDs indicates
the total number of OSPF Database
Description packets transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
helloPackets
long
tmnxOspfIfRxHellos
The value of tmnxOspfIfRxHellos indicates
the total number of OSPF Hello packets
received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
helloPackets
long
tmnxOspfIfTxHellos
The value of tmnxOspfIfTxHellos indicates
the total number of OSPF Hello packets
transmitted on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfRxLSAcks
The value of tmnxOspfIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
(2 of 8)
F-30
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
linkStateAcknowledgements
long
tmnxOspfIfTxLSAcks
The value of tmnxOspfIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this interface since tmnxOspfAdminState
was last set to 'enabled'.
linkStateRequests
long
tmnxOspfIfRxLSRs
The value of tmnxOspfIfRxLSRs indicates
the total number of Link State Requests
(LSRs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateRequests
long
tmnxOspfIfTxLSRs
The value of tmnxOspfIfTxLSRs indicates
the total number of OSPF Link State
Requests (LSRs)transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateUpdates
long
tmnxOspfIfRxLSUs
The value of tmnxOspfIfRxLSUs indicates
the total number of Link State Updates
(LSUs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateUpdates
long
tmnxOspfIfTxLSUs
The value of tmnxOspfIfTxLSUs indicates
the total number of OSPF Link State
Updates (LSUs) transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
lsasWithBadChecksums
long
tmnxOspfIfRxBadChecksu
ms
The value of tmnxOspfIfRxBadChecksums
indicates the count of LSAs received with
bad checksums.
totalPackets
long
tmnxOspfIfRxPackets
The value of tmnxOspfIfRxPackets
indicates the total number of OSPF
packets received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
totalPackets
long
tmnxOspfIfTxPackets
The value of tmnxOspfIfTxPackets
indicates the total number of OSPF
packets transmitted on this interface
since tmnxOspfAdminState was last set to
'enabled'.
InterfaceStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
authorizationFailures
long
tmnxOspfIfAuthFailures
The value of tmnxOspfIfAuthFailures
indicates the total number of OSPF
packets received with an invalid
authorization key since
tmnxOspfAdminState was last set to
'enabled'.
badAreas
long
tmnxOspfIfBadAreas
The value of tmnxOspfIfBadAreas
indicates the total number of OSPF
packets received with an area mismatch
since tmnxOspfAdminState was last set to
'enabled'.
(3 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-31
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badAuthorizationTypes
long
tmnxOspfIfBadAuthTypes
The value of tmnxOspfIfBadAuthTypes
indicates the total number of OSPF
packets received with an invalid
authorization type since
tmnxOspfAdminState was last set to
'enabled'.
badDeadIntervals
long
tmnxOspfIfBadDeadInterv
als
The value of tmnxOspfIfBadDeadIntervals
indicates the total number of OSPF
packets received where the dead interval
given in the packet was not equal to that
configured on this interface since
tmnxOspfAdminState was last set to
'enabled'.
badDestinationAddresses
long
tmnxOspfIfBadDstAddrs
The value of tmnxOspfIfBadDstAddrs
indicates the total number of OSPF
packets received with the incorrect IP
destination address since
tmnxOspfAdminState was last set to
'enabled'.
badHelloIntervals
long
tmnxOspfIfBadHelloInterv
als
The value of tmnxOspfIfBadHelloIntervals
indicates the total number of OSPF
packets received where the hello interval
given in packet was not equal to that
configured on this interface since
tmnxOspfAdminState was last set to
'enabled'.
badLengths
long
tmnxOspfIfBadLengths
The value of tmnxOspfIfBadLengths
indicates the total number of OSPF
packets received on this interface with a
total length not equal to the length given
in the packet itself since
tmnxOspfAdminState was last set to
'enabled'.
badNeighbors
long
tmnxOspfIfBadNeighbors
The value of tmnxOspfIfBadNeighbors
indicates the total number of OSPF
packets received where the neighbor
information does not match the
information this router has for the
neighbor since tmnxOspfAdminState was
last set to 'enabled'.
badNetworks
long
tmnxOspfIfBadNetworks
The value of tmnxOspfIfBadNetworks
indicates the total number of OSPF
packets received with invalid network or
mask since tmnxOspfAdminState was last
set to 'enabled'.
badOptions
long
tmnxOspfIfBadOptions
The value of tmnxOspfIfBadOptions
indicates the total number of OSPF
packets received with an option that does
not match those configured for this
interface or area since
tmnxOspfAdminState was last set to
'enabled'.
badPacketTypes
long
tmnxOspfIfBadPacketTyp
es
The value of tmnxOspfIfBadPacketTypes
indicates the total number of OSPF
packets received with an invalid OSPF
packet type since tmnxOspfAdminState
was last set to 'enabled'.
(4 of 8)
F-32
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badVersions
long
tmnxOspfIfBadVersions
The value of tmnxOspfIfBadVersions
indicates the total number of OSPF
packets received with bad OSPF version
numbers since tmnxOspfAdminState was
last set to 'enabled'.
badVirtualLinks
long
tmnxOspfIfBadVirtualLink
s
The value of tmnxOspfIfBadVirtualLinks
indicates the total number of OSPF
packets received on this interface that
are destined to a virtual link that does not
exist since tmnxOspfAdminState was last
set to 'enabled'.
discardPackets
long
tmnxOspfIfDiscardPacket
s
The value of tmnxOspfIfDiscardPackets
indicates the total number of OSPF
packets discarded on this interface since
tmnxOspfAdminState was last set to
'enabled'.
retransmitOuts
long
tmnxOspfIfRetransmitOut
s
The value of tmnxOspfIfRetransmitOuts
indicates the total number of OSPF
Retransmits sent on this interface since
tmnxOspfAdminState was last set to
'enabled'.
InterfaceTransmitStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfIfStatsTable
Monitored class: ospf.Interface
databaseDescriptionPackets
long
tmnxOspfIfRxDBDs
The value of tmnxOspfIfRxDBDs indicates
the total number of OSPF Database
Description packets received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
databaseDescriptionPackets
long
tmnxOspfIfTxDBDs
The value of tmnxOspfIfTxDBDs indicates
the total number of OSPF Database
Description packets transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
helloPackets
long
tmnxOspfIfRxHellos
The value of tmnxOspfIfRxHellos indicates
the total number of OSPF Hello packets
received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
helloPackets
long
tmnxOspfIfTxHellos
The value of tmnxOspfIfTxHellos indicates
the total number of OSPF Hello packets
transmitted on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfRxLSAcks
The value of tmnxOspfIfRxLSAcks
indicates the total number of Link State
Acknowledgements received on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateAcknowledgements
long
tmnxOspfIfTxLSAcks
The value of tmnxOspfIfTxLSAcks
indicates the total number of OSPF Link
State Acknowledgements transmitted on
this interface since tmnxOspfAdminState
was last set to 'enabled'.
(5 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-33
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
linkStateRequests
long
tmnxOspfIfRxLSRs
The value of tmnxOspfIfRxLSRs indicates
the total number of Link State Requests
(LSRs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateRequests
long
tmnxOspfIfTxLSRs
The value of tmnxOspfIfTxLSRs indicates
the total number of OSPF Link State
Requests (LSRs)transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
linkStateUpdates
long
tmnxOspfIfRxLSUs
The value of tmnxOspfIfRxLSUs indicates
the total number of Link State Updates
(LSUs) received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
linkStateUpdates
long
tmnxOspfIfTxLSUs
The value of tmnxOspfIfTxLSUs indicates
the total number of OSPF Link State
Updates (LSUs) transmitted on this
interface since tmnxOspfAdminState was
last set to 'enabled'.
totalPackets
long
tmnxOspfIfRxPackets
The value of tmnxOspfIfRxPackets
indicates the total number of OSPF
packets received on this interface since
tmnxOspfAdminState was last set to
'enabled'.
totalPackets
long
tmnxOspfIfTxPackets
The value of tmnxOspfIfTxPackets
indicates the total number of OSPF
packets transmitted on this interface
since tmnxOspfAdminState was last set to
'enabled'.
NeighborGeneralStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfNbrStatsTable
Monitored class: ospf.Neighbor
events
long
tmnxOspfNbrEvents
The value of tmnxOspfNbrEvents
indicates the number of times this
neighbor relationship has changed state,
or an error has occurred.
retransmissionQueueLength
long
tmnxOspfNbrLsRetransQL
en
The value of tmnxOspfNbrLsRetransQLen
indicates the current length of the
retransmission queue.
NeighborStatusStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfNbrStatsTable
Monitored class: ospf.Neighbor
badMtus
long
tmnxOspfNbrBadMTUs
The value of tmnxOspfNbrBadMTUs
indicates the total number of times when
the MTU in a received database
description packet was larger than the
MTU of the receiving interface since
tmnxOspfAdminState was last set to
'enabled'.
(6 of 8)
F-34
December 2009
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
Statistics Management Guide
3HE 04551 AAAE Ed. 01
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
badNeighborStates
long
tmnxOspfNbrBadNbrState
s
The value of tmnxOspfNbrBadNbrStates
indicates the total number of OSPF
packets received when the neighbor state
was not expecting to receive this packet
type since tmnxOspfAdminState was last
set to 'enabled'.
badPackets
long
tmnxOspfNbrBadPackets
The value of tmnxOspfNbrBadPackets
indicates the total number of times when
an LS update was received with an illegal
LS type or an option mismatch since
tmnxOspfAdminState was last set to
'enabled'.
badSequenceNumbers
long
tmnxOspfNbrBadSeqNums
The value of tmnxOspfNbrBadSeqNums
indicates the total number of times when
a database description packet was
received with a sequence number
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
duplicates
long
tmnxOspfNbrDuplicates
The value of tmnxOspfNbrDuplicates
indicates the total number of times when
a duplicate database description packet
was received during the Exchange state
since tmnxOspfAdminState was last set to
'enabled'.
lsaInstallFailed
long
tmnxOspfNbrLsaInstallFai
led
The value of tmnxOspfNbrLsaInstallFailed
indicates the total number of times an
LSA could not be installed into the LSDB
due to a resource allocation issue since
tmnxOspfAdminState was last set to
'enabled'.
lsaNotInLSDB
long
tmnxOspfNbrLsaNotInLsd
bs
The value of tmnxOspfNbrLsaNotInLsdbs
indicates the total number of times when
an LS request was received for an LSA not
installed in the LSDB of this router since
tmnxOspfAdminState was last set to
'enabled'.
numberOfRestarts
long
tmnxOspfNbrNumRestarts
The value of tmnxOspfNbrNumRestarts
indicates the number of times the
neighbor has attempted restart.
optionMismatches
long
tmnxOspfNbrOptionMism
atches
The value of
tmnxOspfNbrOptionMismatches indicates
the total number of times when a LS
update was received with an option
mismatch since tmnxOspfAdminState was
last set to 'enabled'.
SiteStats
MIB table name: TIMETRA-OSPF-NG-MIB.tmnxOspfStatisticsTable
Monitored class: ospf.Site
addRouteFailed
long
tmnxOspfRoutesAddsFail
ed
The value of tmnxOspfRoutesAddsFailed
indicates the number of times an attempt
to add a route to the Route Table Manager
(RTM) failed for this OSPF instance.
cspfDroppedRequests
long
tmnxOspfCSPFDroppedRe
quests
The value of
tmnxOspfCSPFDroppedRequests indicates
the number of dropped CSPF requests
made by the OSPF protocol.
(7 of 8)
Alcatel-Lucent 5620 Service Aware Manager, Release 7.0 R6
3HE 04551 AAAE Ed. 01
Statistics Management Guide
December 2009
F-35
F. 7701 CPAA Release 3.0 statistics counters
5620 SAM counter name
Type
MIB counter name
Description
cspfPathsFound
long
tmnxOspfCSPFPathsFoun
d
The value of tmnxOspfCSPFPathsFound
indicates the number of of paths found for
the requests made to OSPF protocol.
cspfPathsNotFound
long
tmnxOspfCSPFPathsNotFo
und
The value of
tmnxOspfCSPFPathsNotFound indicates
the number of of paths not found for the
requests made to OSPF protocol.
cspfRequests
long
tmnxOspfCSPFRequests
The value of tmnxOspfCSPFRequests
indicates the number of CSPF requests
made to the OSPF protocol.
deleteRouteFailed
long
tmnxOspfRoutesDelsFaile
d
The value of tmnxOspfRoutesDelsFailed
indicates the number of times an attempt
to delete a route from the Route Table
Manager (RTM) failed for this instance of
OSPF.
inOverflowCount
long
tmnxOspfNumTimesInOve
rflow
The value of
tmnxOspfNumTimesInOverflow indicates
the count of the number of times the
system was in the overflow state.
inOverloadCount
long
tmnxOspfNumTimesInOve
rload
The value of
tmnxOspfNumTimesInOverload indicates
the count of the number of times the
system was overloaded.
modifyRouteFailed
long
tmnxOspfRoutesModsFail
ed
The value of tmnxOspfRoutesModsFailed
indicates the number of times an attempt
to modify a route in the Route Table
Manager (RTM) failed for this instance of
OSPF.
newLsasOriginated
long
tmnxOspfOriginateNewLs
as
The value of tmnxOspfOriginateNewLsas
indicates the number of new link-state
advertisements that have been
originated. This number is incremented
each time the router originates a new
LSA.
newLsasReceived
long
tmnxOspfRxNewLsas
The value of tmnxOspfRxNewLsas
indicates the number of link-state
advertisements received determined to
be new instantiations. This number does
not includ