advertisement
HD-SDI CAMERA
User Manual
SCB-6001
PT01-000568B-SCB-6000-ENGLISH-.indb 1 2011-07-05 오후 2:33:12
HD-SDI Camera
User Manual
Copyright
©2013 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
•
•
If the system behaves abnormally because you run a program irrelevant to the system operation.
Deteriorated performance or natural worn-out in process of time
Design and specifications are subject to change without prior notice.
PT01-000568B-SCB-6000-ENGLISH-.indb 2 2011-07-05 오후 2:33:12
overview
important Safety inStructionS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
English
_3
2011-07-05 오후 2:33:12 PT01-000568B-SCB-6000-ENGLISH-.indb 3
overview
warninG
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
caution caution
riSK of eLectric SHocK.
Do not open
CAUTION
: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
eXpLanation of GrapHicaL SymBoLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
4_
overview
PT01-000568B-SCB-6000-ENGLISH-.indb 4 2011-07-05 오후 2:33:12
class construction
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.
when used outside of the u.S., it may be used Har code with fittings of an approved agency is employed.
caution
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Please use the input power with just one camera and other devices must not be connected.
The BNC Out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage or malfunction to the product.
PT01-000568B-SCB-6000-ENGLISH-.indb 5
English
_5
2011-07-05 오후 2:33:12
overview
Please read the following recommend safety precautions carefully.
y
Do not place this apparatus on an uneven surface.
y
Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
y
Do not place this apparatus near conductive material.
y
Do not attempt to service this apparatus yourself.
y
Do not place a glass of water on the product.
y
Do not install near any magnetic sources.
y y
Do not place heavy items on the product.
y
Do not block any ventilation openings.
Do not expose the camera to radioactivity.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
y
Reference : In case of providing information for helping of product’s usages y
Notice : If there’s any possibility to occur any damages for the goods and human caused by not following the instruction
Please read this manual for the safety before using of goods and keep it in the safe place.
6_
overview
PT01-000568B-SCB-6000-ENGLISH-.indb 6 2011-07-05 오후 2:33:12
contentS
oveRvIeW
3
3
8
Important Safety Instructions
Product Features
9 What’s Included
10 At a Glance
InSTALLATIon &
ConneCTIon
13
13 Mounting the Lens
15 Connecting with other Device
opeRATIng YouR CAmeRA
18
18 Menu Configuration
19 Menu Setup
AppenDIx
35
35 Troubleshooting
36 Specification
38 Product Overview
English
_7
2011-07-05 오후 2:33:12 PT01-000568B-SCB-6000-ENGLISH-.indb 7
overview
proDuct featureS
• Supports full HD-SDi video
By adopting a diagonal 6mm (1/3”) 2M pixel CMOS, the camera produces clear picture quality.
• excellent low-illumination image quality
By adopting high-sensitive colour CMOS, the camera provides clear image quality under a severe low illumination condition of 0.017 Lux (with SENS-UP, 60x).
• SSnr3 (Samsung Super noise reduction) function
The high-performance WN2 DSP chip effectively removes low-light gain noise and afterimage to provide clear images even in dark environments.
• Day& night(icr)
This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and B/W mode operates in night-time conditions to enhance the definition of the image.
•
INTELLIGENCE
Once motion is detected, the camera sends an alert signal to the processing unit, which, if used in conjunction with an optional alarm, can provide effective surveillance of your property.
• SSDr (Samsung Super Dynamic range)
For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness.
• miscellaneous functions
HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM and PRIVACY functions are provided.
• oSD
By providing multi-lingual user-friendly OSD (On-screen Display) menu, the camera provides easy handling of the camera.
8_
overview
PT01-000568B-SCB-6000-ENGLISH-.indb 8 2011-07-05 오후 2:33:12
wHat’S incLuDeD
Check if the main unit and all the following accessories are included in the product package.
Appearance Item Name Quantity Description
1
Camera
Quick Manual 1
C Mount Adapter
Auto Iris Lens Connector
1 Used to install the camera lens
Cable for the testing monitor 1
Used to test the camera connection to a portable display device
PT01-000568B-SCB-6000-ENGLISH-.indb 9
English
_9
2011-07-05 오후 2:33:12
overview
at a GLance front Side
a b c a
Mounting Bracket
Screw Hole b c
Item
Auto Iris Lens
(Optional)
Auto Iris Lens
Connector
Description
Used to fix the camera on a bracket or mounting bracket.
The screw size : use this screw to fix the mounting bracket .
1/4” -20UNC(20THREAD)
L : 4.5mm±0.2mm (ISO Standard), or
0.197” (ASA Standard)
Installed on the lens adaptor.
Used to supply power and output signal to control the iris of the lens.
M
`
Mounting Bracket is not included.
For more information to use mounting bracket, refer to the product’s documentation.
10_
overview
PT01-000568B-SCB-6000-ENGLISH-.indb 10 2011-07-05 오후 2:33:13
rear Side
h a b c
HD-SDI
VIDEO
POWER
1 : GND
2 : EXT_D/N
3 : MD_OUT
4 : RS_485+
5 : RS_485d e f g
Item a
HD-SDI Video Out terminal
Description
BNC terminal for HD-SDI video signal output.
b c
Focus Adjustment
Button d
SETUP Switch
VIDEO
The switch is used for setting and adjusting the camera’s functions and properties.
_
/
+
Move this switch left or right to move the cursor or change the value in the menu.
When menu is off, use this switch for adjusting focus.
$
@
/
%
Move this switch up or down to move the cursor in the menu.
Press the switch to set the function in menu. To move to a submenu item in the menu, press this switch.
Press and hold this button more than 2 seconds to restores the focus adjustment to the default flange back position.
Short to press this button to fit the focus automatically.
Analogue video output terminal of Video.
Use a monitor cable for testing the camera with a portable display.
(for installation)
English
_11
PT01-000568B-SCB-6000-ENGLISH-.indb 11 2011-07-05 오후 2:33:13
overview
Item e
Power LED f
GND g
Power Port h
I/O Port
Description
This lamp turns green when the proper power is applied to the camera.
Used for earth-grounding.
Used to plug the power cable.
1:GND
2:EXT_D/N
3:MD_OUT
4:RS-485+
5:RS-485–
Earth-grounding port for external signal.
External signal input port for Day/Night mode setup.
Output port that signals when a motion is detected.
Signal port for RS-485 communication.
Signal port for RS-485 communication.
12_
overview
PT01-000568B-SCB-6000-ENGLISH-.indb 12 2011-07-05 오후 2:33:13
installation & connection
mountinG tHe LenS
Disconnect the power before proceeding.
M
`
The C lens and CS lens are not included in the product package.
J
`
If using a normal commercial lens, you may encounter out of focus when switching to BW mode .
To prevent this, it is recommended to use the IR mega lens.
mounting the cS lens
Turn the optional CS lens clockwise to insert it.
CS Lens
mounting the c lens
Turn the C mount adaptor clockwise to insert it and do the same with the C lens.
C Lens
English
_13
2011-07-05 오후 2:33:14 PT01-000568B-SCB-6000-ENGLISH-.indb 13
installation & connection
connecting the auto iris Lens connector
Insert the lens connector into the corresponding hole of the camera.
focusing
Turn the lens left or right to control the zoom and focus the lens so that you can view a clear, sharp object.
M
`
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol.
Set up the focus, the first is restores the focus adjustment to the default flange back position, then focusing with the zoom lever of the lens, press the [ to adjust the lens even more clearly.
FOCUS ] button on the rear of the camera
14_
installation & connection
PT01-000568B-SCB-6000-ENGLISH-.indb 14 2011-07-05 오후 2:33:14
connectinG witH otHer Device
HD-SDI Monitor
HD-SDI
HD-SDI
Day/Night mode controller
VIDEO
POWER
1 : GND
2 : EXT_D/N
3 : MD_OUT
4 : RS_485+
5 : RS_485-
Test monitor for installation
Motion detection output device
connecting to the monitor
Connect the video out port of the camera to the video input port of the monitor.
J
`
To check the display screen after installing the camera for the first time, you can use the Video port to check the video screen.
`
You can set the video output type to either NTSC or PAL. (page 29).
`
The Video source (4:3) will be displayed with either side truncated in comparison with the
HD-SDI video.
`
The video source from the HD-SDI port can be displayed on the dedicated monitor. To display the source on a commercial monitor, you need a converter to convert the video signal as appropriate.
video cable
The cable connecting the camera’s video output and a monitor is a BNC coaxial cable as shown below.
If the distance between the camera and the monitor exceeds the recommended maximum, please us an auxiliary video amp.
Maximum video transfer distance
100~140m
200m
Recommended cable specification
5C2V(75ohm)
L-6CHD(75ohm)
(SDI-specific Cable)
English
_15
PT01-000568B-SCB-6000-ENGLISH-.indb 15 2011-07-05 오후 2:33:14
installation & connection
external Day/night Switching input
Day/Night mode of the camera can be switched by signal from an external device.
J
`
To use this function, < DAY/NIGHT > setting of the camera should be set to the < EXTERN >.
(Page 27)
motion Detection Signal out
Upon a motion detection, the port outputs signal for an external device for display or operation.
When a motion is detected, the port outputs 3.3V signal.
J
`
To use this function, < ALARM OUT > setting of the camera should be set to < ON >. (Page 31)
power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.
J
`
Be careful not to reverse the polarity when you connect the power cable.
`
Be sure to turn the power off the device to be connected.
DVR
HD-SDI
VIDEO
POWER
1 : GND
2 : EXT_D/N
3 : MD_OUT
4 : RS_485+
5 : RS_485-
System Controller
Power or
PC
for ac/Dc power Supply
You can use either one of AC 24V/1A~2A and DC 12V/2A~4A adaptor.
16_
installation & connection
PT01-000568B-SCB-6000-ENGLISH-.indb 16 2011-07-05 오후 2:33:15
resistance of copper wire [at 20°c (68°f)]
Wire specification (AWG) #24(0.22mm
2
) #22(0.33mm
2
) #20(0.52mm
2
) #18(0.83mm
2
)
Resistance (Ω/m)
0.078
Voltage Drop (V/m)
0.028
Recommended Distance (m) Less than 20
0.050
0.018
Less than 30
0.030
0.011
Less than 30
0.018
0.006
Less than 30
• As shown in the table above, you may encounter a voltage-sag depending on the wire length. If you use an excessively long wire for camera connection, the camera may not work properly.
`
Voltage for proper camera operation: DC 12V±10%, AC 24V±10%
`
Voltage drop shown in the table above may show difference from the actual depending on the manufacturer and cable type.
rS-485 communications
Using RS-485 communication, the camera menu can be accessed using Samsung
Techwin’s System Controller or the DVR.
•
For accessing the camera from a computer
Use a RS-485 converter to connect the camera’s control port with the computer’s serial cable.
Ex) Serial port (COM1) of computer
Serial Cable
RS-485 Converter
Camera’s
RS-485 control port
•
For accessing the camera from a DvR or the System Controller
connect the camera’s RS-485+ and RS-485– terminals to the RS-485 control board’s terminals of desired device with a RS-485 cable (TRX+ and TRX–).
Control ports of RS-485 Controller
(+) CONNECTION TERMINAL (TRX+)
(–) CONNECTION TERMINAL (TRX–)
RS-485 ports of the camera
485+
485–
Default rS-485 communication settings
Item
Default
CAM ID
1
BAUD RATE
9600
UART MODE
8-N-1
RET PKT
ENABLE
J
`
When constructing a proprietary controller for direct camera control, apply Pelco-D or Samsung-
Techwin protocol.
`
Use only a DVR model that supports HD-SDI saving.
English
_17
PT01-000568B-SCB-6000-ENGLISH-.indb 17 2011-07-05 오후 2:33:15
Operating Your Camera
menu confiGuration
LENS
EXPOSURE
WHITE BAL
SIMPLE FOCUS
BACKLIGHT
SSNR3
DAY/NIGHT
SPECIAL
MAIN SETUP
• DC
• BRIGHTNESS
• SENS-UP
• RETURN
• ATW
•
•
•
OUTDOOR
INIT
OFF
• WDR
➝
SET
• MANUAL
• SHUTTER
• DEFOG
• MANUAL
• INDOOR
• FOCUSING
➝
SET
• BLC
• ON
• AUTO
• B/W
• CAM TITLE
• PRIVACY
• LANGUAGE
• OFF
• EXTERN
•
•
•
IMAGE ADJ
PROFILE
RESET
EXIT
• P-IRIS
• AGC
•
SSDR
• AWC
➝
SET
• HLC
• COLOR
• INTELLIGENCE
• COMM ADJ
• RETURN
18_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 18 2011-07-05 오후 2:33:15
menu Setup
To configure the camera’s function settings, use the button on the rear side of the product.
HD-SDI
1 : GND
2 : EXT_D/N
3 : MD_OUT
4 : RS_485+
5 : RS_485-
VIDEO
POWER
•
$%
: Moves up/down in menu.
•
_+
: Moves right/left in menu.
•
@
:
Press the switch to set the function in camera menu.
To move to a sub-menu item in the menu, press this switch.
1. Press the SET button.
• Enters the function menu.
The selected function’s menu appears on the monitor.
2 : EXT_D/N 5 : RS-485-
3 : MD_OUT to set the desired item.
►
2. EXPOSURE
MAIN SETUP
1. LENS DC
3. WHITE BAL
4.
SIMPLE FOCUS
DC 12V
AC 24V
➝
ATW
SET
GND to change the selection.
INIT
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
2. Use the Up/Down buttons to select a desired function.
• Move the button up or down to move the arrow up or down.
Set the arrow to indicate the desired item.
PT01-000568B-SCB-6000-ENGLISH-.indb 19
English
_19
2011-07-05 오후 2:33:15
Operating Your Camera
3. Use the Up/Down buttons to select a desired function.
• Move the button right or left to display available values or settings.
Set the desired setting value using the button.
4. To finish, select < eXit > and press the SET button.
M
`
An item with the icon also has sub menus. To select a sub menu, select an item with the icon press the Function Setup switch.
`
An item with the --- icon is unavailable due to function settings.
LenS
Using this function, you can choose lens type.
1. When the SETUP menu screen is displayed, select < LenS > by using the Function Setup switch so that the arrow indicates < LenS >.
2. Select the connected lens type by using the
Function Setup switch.
• Dc : Select Auto Iris Lens.
• manual : Select Manual Lens
• p-iriS : It is selected to use the iris control lens equipped with a step motor.
- Auto : The iris is automatically adjusted to the amount of the surrounding light.
- Manual : Sets the iris manually to the desired
position.
MAIN SETUP
► 1. LENS
2. EXPOSURE
3. WHITE BAL
4. SIMPLE FOCUS
➝
DC
ATW
SET
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
INIT
5. BACKLIGHT OFF
►
1. MODE
2.
RETURN
P-IRIS SETUP
AUTO
20_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 20 2011-07-05 오후 2:33:15
eXpoSure
1. When the SETUP menu screen is displayed, select < eXpoSure > by using the Function
Setup switch so that the arrow indicates
< eXpoSure > .
2. Select a desired mode using the Function
Setup switch.
• BriGHtneSS : Adjust the screen brightness.
MAIN SETUP
►
1. LENS
2. EXPOSURE
3. WHITE BAL
4. SIMPLE FOCUS
➝
DC
ATW
SET
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
INIT
5. BACKLIGHT OFF
• SHutter : You can select the shutter.
– – – : 1/30sec
A.FLK
: Select this when you experience picture flicker, this happen when there is a clash with the installed lighting frequency.
ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject.
►
EXPOSURE SETUP
1. BRIGHTNESS
ESC
3. AGC
5.
6. SSDR
7. RETURN
HIGH
DEFOG
ON
---
MANUAL : You can control shutter speed manually (1/30sec ~ 1/16,000sec)
J
`
When you use a DC lens, set the shutter mode to --- if color rolling occurs.
`
Carefully position the camera when installing, since produced image quality might be poor if framing a bright light source while the shutter mode of EXPOSURE is set to AUTO.
`
When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
• aGc(auto Gain controL) : The higher the gain level, the brighter the screen - but the greater the noise.
OFF : Not being used
Low : Allows automatic gain control from 5.3dB to 20dB.
Medium : Allows automatic gain control from 5.3dB to 26dB.
High : Allows automatic gain control from 5.3dB to 32dB.
• SenS-up : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.
OFF : Deactivates the SENS-UP function.
AUTO : Activates the SENS-UP function.
English
_21
PT01-000568B-SCB-6000-ENGLISH-.indb 21 2011-07-05 오후 2:33:15
Operating Your Camera
• DefoG : Through the defogging function, camera can automatically recognize fog concentration of the image, defog, self correct in hazy, rainy, flue gas and other inclement weather to get a clear image.
AUTO : The camera will automatically correct image according to the defogging level
(low, middle, high) set by the user.
MANUAL : The camera will adjust the definition of the image according to user's preferences through the defogging level (low, middle, high).
OFF : Turn off Defogging function.
► LEVEL
RETURN
DEFOG SETUP
MIDDLE
• SSDR( samsung super dynamic Range) : SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas.
ON :
Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas.
OFF : Turn off SSDR function.
SSDR ON SSDR OFF
• return : Select this to save the changes in the EXPOSURE menu and return to the MAIN SETUP menu.
J
`
Press the SET button while in AUTO mode to adjust the automatic scene accumulation multiplier for low-illumination operation. (2x ~ 60x)
`
The greater the video accumulation factor is, the brighter the screen is but the afterimage of a moving object grows accordingly.
`
Although noise, spots, and whitish symptoms may occur in higher accumulation, this is normal.
`
If the gain control (AGC) of EXPOSURE mode is set to OFF, SENS-UP mode is accordingly set to
‘- - -‘.
22_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 22 2011-07-05 오후 2:33:15
wHite BaL (wHite BaLance)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select < wHite BaL >. by using the Function
2.
Setup switch so that the arrow indicates
< wHite BaL >.
Select a desired mode using the Function
Setup switch.
MAIN SETUP
►
1. LENS
2. EXPOSURE
3. WHITE BAL
4.
SIMPLE FOCUS
➝
DC
ATW
SET
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
INIT
5. BACKLIGHT OFF
Select one of the following 5 modes, as appropriate for your purpose.
• atw : Select this when the color temperature is between 2,400˚K and 11,000˚K.
• outDoor : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
• inDoor : Select this when the color temperature is between 4,500˚K and 8,500˚K.
• manuaL : Select this to fine-tune White
Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and the Function Setup switch.
• awc
➞
Set : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it.
►
WHITE BAL MANUAL SETUP
RED
BLUE
RETURN
J
`
White Balance may not work properly under the following conditions. In this case select the AWC mode.
When the ambient illumination of the subject is dim.
If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.
PT01-000568B-SCB-6000-ENGLISH-.indb 23
English
_23
2011-07-05 오후 2:33:15
Operating Your Camera
SimpLe focuS
You can adjust the focus of video image.
1. When the SETUP menu screen is displayed, select <
Setup switch so that the arrow indicates
<
SIMPLE FOCUS
> by using the Function
SIMPLE FOCUS
>.
2.
•
Use the Function Setup switch to set up the
focus.
init
➝
Set
: Restores the focus adjustment to the default flange back position.
• focuSinG
➝
Set : Select this to fit the focus automatically.
MAIN SETUP
►
1. LENS
2. EXPOSURE
3. WHITE BAL
4. SIMPLE FOCUS
➝
DC
ATW
SET
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
INIT
5. BACKLIGHT OFF
J
The focusing set mode may not fit correctly in the following cases:
-
Sudden change to the object in Simple focus mode (sudden movement, appearance or disappearance)
-
Radical change to the brightness in Simple focus mode
Image of a low contrast
-
If the camera is exposed to a strong light source in the front or surroundings
In a situation where Simple focus is hardly applied, try to use the manual focus mode.
BacKLiGHt
This camera is designed so that it delivers a distinctive subject and background at the same time, even when the subject is in backlight, by adopting a function of the proprietary
WN2 DSP chip.
1. When the SETUP menu screen is displayed, select <
Function Setup switch so that the arrow indicates
BacKLiGHt
< BacKLiGHt >.
> by using the
2. Select a desired mode using the Function Setup switch depending on the camera
purpose.
• BLc : Enables a user to select a desired area on a picture and view that area more clearly.
LEVEL : Adjust level of the BLC function.
TOP/BOTTOM/LEFT/RIGHT : Adjust the area
to be enhanced.
BLC SETUP
►
1. LEVEL
2. TOP
3. BOTTOM
4. LEFT
5. RIGHT
6. RETURN
24_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 24 2011-07-05 오후 2:33:15
• HLc (High Light compensation) : If the scene
contains extremely bright light areas such as;
from car headlight, the light can mask out much of the on-screen detail.
-
-
LEVEL : Adjust level of the HLC function.
MASK COLOR masking area.
: Change the color of the
(Black, Red, Blue, Gray, Magenta)
►
5.
6.
3.
4.
1.
2.
LEVEL
MASK COLOR
MASK TONE
7.
TOP
BOTTOM
LEFT
RIGHT
8. RETURN
MASK TONE : Change the brightness of the masking area.
TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.
HLC SETUP
MIDDLE
BLACK
.... .... .... * .... 75
• wDr (wide Dynamic range ) :
It displays a sharp image of the objects in a scene where both bright and dark areas exist.
LEVEL :
Select a sensitivity level of WDR.
► LEVEL
RETURN
WDR SETUP MODE
MIDDLE
• off : Not being used
J
`
Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance.
`
When dark, the HLC is only activated when a bright light exceeding a specific size.
`
The HLC is not activated in day light or when bright light is not present at night.
`
The WDR function may be restricted when the manual or P-iris lens is used.
`
The CVBS don't output when the WDR function is used.
PT01-000568B-SCB-6000-ENGLISH-.indb 25
English
_25
2011-07-05 오후 2:33:16
Operating Your Camera
SSnr3
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select < SSnr3 > by using the Function Setup
2.
• switch so that the arrow indicates < SSnr3
Select a desired mode using the Function
Setup switch.
on
>.
: Activates SSNR3 so that noise is reduced.
• off : Deactivates SSNR3. Noise is not reduced.
►
MAIN SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL
4. SIMPLE FOCUS
➝
DC
ATW
SET
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
INIT
5. BACKLIGHT OFF
3. Set the SSNR3 mode to < on > and press the
Function Setup switch. Then you can adjust the noise reduction level.
J
`
You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the ‘EXPOSURE’ menu is ‘OFF’.
`
When adjusting the noise reduction level in the SSNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image.
Day/niGHt
You can display pictures in color or in black and white.
1. When the SETUP menu screen is displayed, select < Day/niGHt > by using the Function
Setup switch so that the arrow indicates < Day/ niGHt >.
2. Select a desired mode using the Function
Setup switch according to the picture display you want.
• coLor : The picture is always displayed in color.
►
• B/w : The picture is always displayed in black and white.
MAIN SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL
4. SIMPLE FOCUS INIT
➝
DC
ATW
SET
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
26_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 26 2011-07-05 오후 2:33:16
• auto : The mode is switched to < coLor > in a normal environment, but switches to < B/w > mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch.
DWELL TIME : You can select day/night switching delay time from.
➝
5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
DURATION : Adjust the brightness of the lighting where the mode switch occurs.
DAY/NIGHT AUTO SETUP
► 1. COLOR
B/W
DWELL TIME
DURATION
2. B/W
DN
COLOR
DWELL TIME
DURATION FAST
3.
ABF
4. RETURN
5 SEC
10 SEC
OFF
DN
➝
ABF : The video is automatically focused after the lighting mode changes
from Day to Night or vice versa.
• eXtern : Control the image modes of Color and B/W when an external controller is synchronized via the Alarm In port.
J
`
When AGC in the EXPOSURE menu is ‘OFF’, AUTO mode is not available to select.
SpeciaL
1. When the SETUP menu screen is displayed, select < SpeciaL > by using the Function Setup switch so that the arrow indicates < SpeciaL >.
MAIN SETUP
►
1. LENS
2. EXPOSURE
3. WHITE BAL
4. SIMPLE FOCUS INIT
➝
DC
ATW
SET
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
2. Select a desired mode using the Function
Setup switch.
SPECIAL SETUP
►
5.
6.
7.
8.
9.
1. CAM TITLE
2. IMAGE ADJ
3. INTELLIGENCE
4. PRIVACY
PROFILE
RESET
RETURN
OFF
OFF
BASIC
COMM ADJ
LANGUAGE ENGLISH
English
_27
PT01-000568B-SCB-6000-ENGLISH-.indb 27 2011-07-05 오후 2:33:16
Operating Your Camera
• cam titLe : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates < cam titLe >.
2) Set it to < on > by using the Function Setup switch.
3) Press the Function Setup switch.
CAMERA TITLE SETUP a B c D e f G H i J K L m n o p Q r S t u v w X y Z a b c d e f g h i j k l m n o p q r s t u v w x y z
– . 1 2 3 4 5 6 7 8 9
← → C L R P O S E N D
— — — — — — — — — — — — — —
4) Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch. Repeat this to enter multiple letters. You can enter up to 15 letters.
5) Enter a title, move the cursor to < poS > and press the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the Function Setup switch and press the Function Setup switch. When the position is determined, select < enD > and press the Function Setup switch to return to the
SPECIAL menu.
ABCD
←→↑↓ to Locate, then SET
J
`
When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one.
`
Only English is available in this mode.
`
If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted.
To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch.
Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.
28_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 28 2011-07-05 오후 2:33:16
• imaGe aDJ :
1) When the SPECIAL menu screen is displayed, select < imaGe aDJ > by using the Function
Setup switch so that the arrow indicates
< imaGe aDJ >.
SPECIAL SETUP
►
5.
6.
7.
8.
9.
1. CAM TITLE
2. IMAGE ADJ
3. INTELLIGENCE
4. PRIVACY
PROFILE
RESET
RETURN
OFF
OFF
BASIC
COMM ADJ
LANGUAGE ENGLISH
2) Select a desired mode using the Function Setup switch.
MONITOR : Please change the settings value of video appropriate to your monitor.
• LCD : Please select this menu item when using an LCD monitor.
• USER : Please use this menu item when using a monitor other than standard ones.
You can change the gamma, reset in the sub menus. color level and
H-REV : You can flip the picture horizontally on the screen.
►
V-REV : You can flip the picture vertically on the screen.
D-ZOOM : You can use a digital zoom of x2 ~ x16.
IMAGE SETUP
1. MONTIOR LCD
2. H-REV OFF
3. V-REV OFF
4. D-ZOOM OFF
7.
8.
5.
6.
DIS
VIDEO OUT FORMAT
9. RETURN
OFF
SHARPNESS ON
OSD COLOR WHITE
DIS : Compensates the image automatically when it is seen to shake for stable image output.
SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture.
OSD COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)
VIDEO OUT FORMAT
•
: Sets the video size and video fmt.
VIDEO SIZE : Sets the image resolution of the HD-SDI output of the camera.
•
Select the desired setting and press the SET button. (NTSC : 1080i 60, 1080p 30,
720p 60 ; PAL : 1080i 50, 1080p 25, 720p 50)
VIDEO FMT : Sets the video output format of the Video port on the camera provided
for test and installation.(NTSC, PAL)
RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu.
J
`
If you increase the sharpness level excessively, the image may be displayed abnormally or it can cause a noise.
English
_29
PT01-000568B-SCB-6000-ENGLISH-.indb 29 2011-07-05 오후 2:33:16
Operating Your Camera
• inteLLiGence : Commands the camera to motion-detect and trace an object.
DETECTION : Since the camera detects motion without any additional external sensor, you can monitor activity more effcient.
► 1. DETECTION
2. TRACKING
3. FIXED/MOVED
4. TAMPERING
5. DETECT BOX
RETURN
6. ALARM OUT
7. SETUP CONFIG
8.
INTELLIGENCE
OFF
OFF
OFF
OFF
OFF
OFF
TRACKING : Commands the camera to detect
and trace a moving object.
TRACKING
▶
▶
TYPE : Two types, line and area, of fences are available.
COUNT : Displays the number of times that an object enters or leaves a fenced area.
► 1. TYPE
2. COUNT
3. DISPLAY
4. FILL
5. POSITION
6. RETURN
LINE
OFF
ON
OFF
▶
DISPLAY : Determines whether to use the fence selected in the FENCE.
▶ FILL : Fill or remove color from the FENCE.
▶ POSITION : Defines the position and detection direction of a line or fenced area.
1) LINE FENCE
- SEL POS : Selects a position from POS1,POS2.
- X POS / Y POS : Adjust the size and position of the selected line fence.
- DIRECTION
·
DIR1 : Detects objects moving right to left on the fence line.
·
DIR2 : Detects objects moving left to right on the fence line.
·
DIR1/2 : Detects all objects moving crosswise on the fence line.
-
RETURN : Select this to save the POSITION menu settings and return to the
TRACKING menu.
2) AREA FENCE
- X POS / Y POS : Adjust the size and position of the selected area fence.
- DIRECTION
·
·
·
IN : Detects objects entering the fenced area.
OUT : Detects objects exiting the fenced area
IN/OUT : Detects all objects entering and exiting the fenced area.
- RETURN : Select this to save the POSITION menu settings and return to the
TRACKING menu.
▶ RETURN : Select this to save the TRACKING menu settings and return to the
INTELLIGENCE menu.
30_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 30 2011-07-05 오후 2:33:16
►
X POS
Y POS
DIRECTION
RETURN
TRACKING
.... .. .. .... ....
POS1
106
* .... .... .... .... 12
DIR1
►
X POS
Y POS
DIRECTION
RETURN
TRACKING
.... .. .. .... ....
POS1
106
- FIXED/MOVED : stays onscreen without movement
.
J
`
A detection (FIXED/MOVED) error may occur if :
· multiple motions occur continuously in random directions
· a fixed object moves in one position continuously
· a second object screens the first moving object
- TAMPERING
: as blocked lens.
You can set to detect tampering attempts and trigger events, such
- DETECT BOX : Outlines an object on the screen in a box when its movement matches a custom Motion Type.
-
ALARM OUT : Releases a signal from the MD Output Terminal of the camera when an object’s movement matches a custom Motion Type.
-
SETUP CONFIG :
▶
DETECT AREA : Defines the Motion
Detection area.
· AREA SEL: You can select up to 4 areas.
·
MODE : Determines whether to use the area selected in the AREA.
·
DETECT ALARM : Determines whether to use the detect alarm selected in the
AREA.
► 1.
2. SENSITIVITY
3. DET.SIZE
4. RETURN
SETUP CONFIG
3
3
· TOP / BOTTOM / LEFT / RIGHT : Adjust
the size and position of the selected area.
·
AREA menu settings and return to the
SETUP CONFIG menu.
►
MODE
DETECT ALARM
TOP
BOTTOM
LEFT
RIGHT
RETURN
AREA
OFF
1
OFF
* .... .... .... .... 1048
* .... .... .... .... 1088
English
_31
PT01-000568B-SCB-6000-ENGLISH-.indb 31 2011-07-05 오후 2:33:16
Operating Your Camera
▶
SENSITIVITY : Set the sensitivity of the motion detection. When adjusting the
sensitivity, note that the lower the level means the higher sensitivity.
▶
DET. SIZE : Selects an object size to detect on the screen. When adjusting the
detection size, note that the higher the level means the bigger detection size.
-
▶ RETURN : Select this to save the SETUP CONFIG menu settings and return to the INTELLIGENCE menu.
RETURN : Select this to save the INTELLIGENCE menu settings and return to the
SPECIAL menu.
• privacy : You can specify a certain area of the
camera video to be protected for your privacy.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates < privacy >.
2) Set up the mode using the Function Setup switch.
PRIVACY
► 1.
2. 2
1
TYPE
3. RETURN
OFF
OFF
TYPE 1 ( area is rectangular )
,
▶
▶
AREA SEL: Y ou can select up to 16 PRIVACY
areas.
AREA MODE : Determines whether to use the area selected in the AREA SEL.
▶
▶
▶
MASK COLOR
: Determine area color. You can select Green, Red, Blue, Black, White, Gray.
TOP / BOTTOM / LEFT / RIGHT :
Adjust the size and position of the selected area.
RETURN
: Select this to save the TYPE 1 menu settings and return to the PRIVACY menu.
► 1.
2. AREA MODE
3. MASK COLOR
4. TOP
5. BOTTOM
6. LEFT
7. RIGHT
8. RETURN
TYPE 2 ( area is polygonal )
,
▶
AREA SEL: Y ou can select up to 4 PRIVACY
areas.
▶
AREA MODE : Determines whether to use the area selected in the AREA SEL.
▶
▶
MASK COLOR
: Determine area color. You can select Green, Red, Blue, Black, White, Gray.
SEL POS/XPOS/YPOS : Adjust the size and position of the selected area.
► 1.
2. AREA MODE
3. MASK COLOR
4. SEL POS
5.
6.
X POS
Y POS
7. RETURN
AREA1
OFF
GRAY
* .... .... .... ....
59
... . .... .... ....
35
67
AREA1
OFF
GRAY
32_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 30 2011-07-05 오후 2:33:16
▶ RETURN
: Select this to save the TYPE 2
PRIVACY menu.
menu settings and return to the
RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
pROfIle : S elect a desired mode using the Function
Setup switch according to the picture display you
want.
SPECIAL SETUP
-
-
BASIC : The most common environment is set
to meet.
DAY/NIGHT : It will be set automatically so it optimizes to the day or night conditions, respectively.
►
5.
6.
7.
8.
9.
1. CAM TITLE
2. IMAGE ADJ
3. INTELLIGENCE
4. PRIVACY
PROFILE
RESET
RETURN
OFF
OFF
BASIC
COMM ADJ
LANGUAGE ENGLISH
BACKLIGHT : It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.
-
ITS : It will be set automatically so you can easily check the traffc conditions.
-
-
INDOOR : It will be set automatically to help you take a picture in a regular indoor lighting condition.
USER : Automatically configures the camera to your custom settings.
1) Select Custom for Simple Setup mode.
2) Configure the menu options to your custom settings.
3) The settings are automatically saved as Custom mode.
4) Profile user mode don't initialize when menu resets.
-
BANK : The system will automatically set if dark and bright area are all exist at same time, sothat you can recognize the object in bank easily.
*
In the PROFILE menu, you can configure the following camera settings at once.
SHUTTER ESC
AGC HIGH
WHITE BAL ATW
BACKLIGHT OFF
SSNR3 ON
DAY/NIGHT AUTO
BASIC DAY/NIGHT BACKLIGHT
ESC
HIGH
ATW
OFF
ON
AUTO
ESC
HIGH
ATW
BLC
ON
AUTO
ITS INDOOR USER
MANUAL(1/250) A
HIGH
.FLK
HIGH
OUTDOOR INDOOR
OFF OFF
ON
AUTO
ON
AUTO
-
-
-
-
-
-
BANK
---
HIGH
ATW
WDR
ON
AUTO
J
`
The BANK can be used when the LENS is select to DC mode.
English
_33
PT01-000568B-SCB-6000-ENGLISH-.indb 31 2011-07-05 오후 2:33:16
Operating Your Camera
• comm aDJ (communication adjustment) :
This function sets up the camera communication status when controlling the camera through an external control device.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates < comm aDJ >.
2) Set up the mode using the Function Setup switch.
►
COMMUNICATION SETUP
1. PROTOCOL
2. CAM ID
3. BAUD RATE
4. UART MODE
5. DISP ID
6. RET PKT
7. RETURN
SAMSUNG-T
* .... .... .... ....
9600
1
8-N-1
OFF
ENABLE
PROTOCOL : Select the communication PROTOCOL. (SAMSUNG-T, SAMSUNG-E,
Pelco-D, Pelco-P, Bosch, Honeywell, Vicon, Panasonic, GE, AD)
CAM ID : Determines the camera's identification number (between 0 and 255).
BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
UART MODE : You can select NONE, EVEN or ODD for the parity bits.
DISP ID : Display camera title on top left corner of the screen.
RET PKT : Specify whether to return the same command to the controlling device when a control command is delivered to the camera.
J
`
When protocol such as SAMSUNG-T,SAMSUNG-E,Pelco-D&Pelco-P are in using, you can use preset95 command to activate Menu.
• LanGuaGe : You can select the menu language according to your requirements.
• reSet : Resets the camera settings to the factory defaults. Communication,
Language, Video Format and Monitor settings are not initialized.
• return : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
eXit
Save the current settings and exit the MAIN SETUP menu.
34_
Operating Your Camera
PT01-000568B-SCB-6000-ENGLISH-.indb 30 2011-07-05 오후 2:33:16
trouBLeSHootinG
PROBLEM
Nothing appears on the screen.
The image on the screen is dim.
SOLUTION y
Check that the power cord and line connection between the camera and monitor are properly connected.
y
When the camera’s HD-SDI BNC output is directly connected to the monitor’s BNC terminal:
Make sure the monitor supports HD-SDI signal input.
y
When the camera’s HD-SDI BNC output is connected to the DVR: Make sure the DVR supports HD-SDI signal input.
y
HD-SDI output is converted into other format such as DVI and VGA by using video converter: Make sure the converter’s HD-SDI input format supports the product’s output video format.
y
Is lens stained with dirt? Clean your lens with soft, clean cloth.
y
Set the monitor to the proper condition.
y
If the camera is exposed to very strong light, change the camera position.
y
Adjust the contrast feature of the monitor.
The image on the screen is dark.
The camera is not working properly, and the surface of the camera is hot.
The SENS-UP function does not work.
The Motion Detection function does not work.
Color is not correct.
y
Check that you have properly connected the camera to an appropriate power source.
y
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
The screen flickers continually.
RS-485 communication is not available.
y
Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
y
Check the setting of WHITE BAL SETUP menu .
y
Ensure the camera is not pointing towards the sun.
y
Is the camera framing the sun or other bright light source?
y
HD-SDI video may not appear to be normal if distance exceeds the maximum transferrable distance.
y
When a BNC cable adaptor is used to combine two or more BNC cables for distributed HD-SDI video transfer, make sure the impedance of the adaptor is 75Ω. Otherwise, it may cause shorter transfer distance or broken video transfer.
y
Check RS-485 communication settings.
English
_35
PT01-000568B-SCB-6000-ENGLISH-.indb 35 2011-07-05 오후 2:33:16
appendix
Specification
Video
Lens Type
Operational
Items Description
Video
Total Pixels
Effective Pixels
Scanning System
Min. Illumination
S / N Ratio
Video Output
Lens Type
Mount Type
On Screen Display
1/3" Progressive Scan CMOS
2,010(H) x 1,108(V), 2.2M Pixels
1,944(H) x 1,092(V), 2.1M Pixels
Progressiv Scan
Color : 1Lux @ F1.2, 0.017 Lux (Sens-up, 60x)
B/W : 0.1 Lux @ F1.2, 0.0017 Lux ( Sens-up, 60x)
50dB (AGC off, Weight on)
SMPTE292M ( HD-SDI ), Monitoring CVBS
Manual / DC Auto Iris / P-Iris
C/CS
Multi-language Support
English, Korean, Japanese, Spanish, French, Portuguese, Chinese,
German, Italian, Russian, Czech, Polish, Rumanian, Serbian, Swedish,
Denish, Turkish
Camera Title
Day & Night
Off / On (Displayed 15 characters)
Auto (ICR), Color, B/W , External
Backlight Compensation
Off / BLC / HLC / WDR
Contrast Enhancement
SSDR ( Off / On )
Digital Noise Reduction
SSNR Ⅲ ( Off / On )
Intelligent Video
Tampering, Virtual Line, Enter/Exit, Appear/Disappear
36_
appendix
PT01-000568B-SCB-6000-ENGLISH-.indb 32 2011-07-05 오후 2:33:16
Operational
Items
Privacy Masking
Sens-up (Frame
Integration)
Gain Control
White Balance
Electronic Shutter
Speed
Digital Zoom
Reverse
Communication
Protocol
Description
Off / On (4 Polygonal + 16 Rectangular zones)
Off / Auto (2x ~ 60x)
Off / Low / Middle / High
ATW / Outdoor / Indoor / Manual / AWC
➝
SET (1,700K° ~ 11,000K°)
Esc / A.FLK / Manual / ---
Off / On (2x ~ 16x)
Off / H-Rev / V-Rev / HV-Rev
RS-485
RS-485 : SAMSUNG-T, SAMSUNG-E, Pelco-D, Pelco-P, Bosch,
Honeywell, Vicon, Panasonic, GE, AD
-10°C~+55°C (14°F~131°F) / ~90% RH
Electrical
Mechanica
Input Voltage
Current
Color / Material
Dimension (WxHxD)
Weight
HD-SDI
Transmission
Distance
5C2V ( 75 ohm )
L-6CHD ( 75 ohm )
Dual ( 24VAC±10% & 12VDC±10% )
1.56A
Body : Dark Gray / Aluminum, Steel
W73.1 x H66.6 x D147.8mm
321g
Max. 100~140m
Max. 200m
`
The maximum transferrable distance of HD-SDI video signal depends on the cable manufacturer or installation conditions.
`
When a BNC cable adaptor is used to combine two or more BNC cables for distributed HD-SDI video transfer, make sure the impedance of the adaptor is 75Ω. Otherwise, the adaptor may cause shorter transfer distance or broken video transfer due to loss of transferred signal.
`
If you intend to install the product outdoors, you must use the housing to meet the temperature/humidity conditions as specified above. In particular, if the product is installed in a place where the temperature falls below zero (0) degree, it is recommended to install a separate heater inside of the housing in an attempt to meet the operating conditions.
※
For enhanced performance, the product specification is subject to change without prior notice.
English
_37
PT01-000568B-SCB-6000-ENGLISH-.indb 33 2011-07-05 오후 2:33:16
appendix
proDuct overview
147.8(5.82")
Unit : mm (inch)
73.1(2.88")
Ø 6.5 HOLE (Ø 0.26") Ø 1/4'-20 UNC-2B
34_
appendix
PT01-000568B-SCB-6000-ENGLISH-.indb 34
14 (0.55")
67.7 (2.67")
2011-07-05 오후 2:33:16
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.
PT01-000568B-SCB-6000-ENGLISH-.indb 35 2011-07-05 오후 2:33:16
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124 www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
PT01-001887A
PT01-000568B-SCB-6000-ENGLISH-.indb 40 2011-07-05 오후 2:33:17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project