Emerson CF990BS00 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
HIGHGROVE
™
54” Ceiling Fan Owner's Manual
Model Number
CF990BS00
CF990VNB00
Net Weight:
Part No. F40BP74640000
27.5
Lbs.
Form No. BP7464
Model No.: CF990
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-2011” and
Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling
fan must be grounded as a precaution against possible electrical shock. Electrical installation
should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least
50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 15.9 kg. (35 lbs.)
or less”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly
used for support of light fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
NOTE: All setscrews must be checked and re-tightened where necessary before installation.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed
control, Model No. UC7067RA manufactured by Rhine Electric Co., Ltd.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson Electric Co. Substitution
of parts or accessories not designated for use with this product by Emerson Electric Co. could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall
control/switch.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
Model No.: CF990
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Installed Wire Length
Up to 50 ft.
50-100 ft.
Tools Needed for Assembly
One Phillips head screwdriver
One 1/4” blade screwdriver
One stepladder
One wire stripper
MATERIALS
WARNING
!
Wiring outlet box and box connectors must be of
type required by the local code. The minimum wire
would be a 3-conductor (2-wire with ground) of the
following size:
Wire Size A.W.G.
14
12
Before assembly your ceiling fan, refer to section
on proper method of wiring your fan (page 8).
If you feel you do not have enough wiring
knowledge or experience, have your fan installed
by a licensed electrician.
Unpacking Instructions
!
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
2. Remove the fan motor assembly from the
protective plastic bag. Place all carton contents on
a protective surface.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
A. FAN MOTOR
ASSEMBLY
B. CEILING
COVER
C. COUPLING
COVER
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
D. FAN
BLADES
a. Fan motor assembly
b. One ceiling cover
c. One coupling cover
d. Five fan blades
e. Five fan blades flanges
f. Five blade medallions
g. One lower housing
h. One light kit assembly including one finial nut
i. One lower glass
j. Two 50-watt mini candelabra halogen light bulbs
k. One hanger bracket
l. One hanger ball/4.5” downrod assembly
m. One receiver and 4-speed hand control
n. One loose parts bag containing:
1. One clevis pin
2. One hairpin clip
3. Three 12 ga. wire connectors
4. Two #8-32 x 1-1/4” threaded studs
5. Two #8 external tooth lockwashers
6. Two #8-32 knurled knobs
7. Sixteen #10-32 x 12.3mm washer head screws
8. Eleven 1/4” x 1/2” round head lock tie flange screws
9. One #8-32 x 10mm pan head screw
10. One balancing kit
E. FAN
BLADE
FLANGES
F. FLANGE
MEDALLIONS
G. LOWER
HOUSING
I. LOWER
GLASS
H. LIGHT KIT
ASSEMBLY
J. LIGHT
BULBS
L. HANGER BALL/
4.5" DOWNROD
ASSEMBLY
K. HANGER
BRACKET
N. LOOSE
PARTS BAG
M. FAN/LIGHT
REMOTE
CONTROL/
RECEIVER
3
Model No.: CF990
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
!
!
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
“Acceptable for Fan Support of 15.9 kg. (35lbs.) oror
less”, and use screws supplied with outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
!
WARNING
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
How to Put Your Ceiling Fan Together
!
WARNING
PIN
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
HANGER
BALL
DOWNROD
1. Remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the clevis pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 5.
2. Loosen setscrew in motor coupling if necessary.
Separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Align the clevis pin holes in the downrod
with the holes in the motor coupling. Install the
clevis pin and secure with the hairpin clip (Figure
2). The clevis pin must go through the holes in the
motor coupling and the holes in the downrod. Be
sure to push the straight leg of the hairpin clip
through the hole near the end of the clevis pin until
the curved portion of the hairpin clip snaps around
the clevis pin. The hairpin clip must be properly
installed to prevent the clevis pin from working
loose. Pull on the downrod to make sure the clevis
pin is properly installed.
!
SETSCREW
Figure 1
DOWNROD
DOWNROD
HAIRPIN
HAIRPIN
CLIP
CLIP
SETSCREW
SETSCREW
(2)
CLEVIS PIN
CLEVIS
WARNING
MOTOR
MOTOR
COUPLING
COUPLING
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
Figure 2
4
Model No.: CF990
How to Put Your Ceiling Fan Together (continued)
3. While pulling up on the downrod, securely tighten
the two setscrews in the motor coupling (Figure 2).
DOWNROD
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.
!
COUPLING COVER
MOTOR
HOUSING
GROMMET
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
4. Make sure the grommet is properly installed in the
coupling cover then slide the coupling cover on the
downrod until it rests on the motor housing
(Figure 3).
5. Place the ceiling cover over the downrod. Be sure
both the ceiling cover and the coupler cover are
oriented correctly (Figure 4).
Figure 3
6. Reinstall the hanger ball (Figure 4) on the downrod as
follows. Route the motor leads through the downrod.
Position the pin through the two holes in the downrod
and align the ball so the pin is captured in the groove
in the top of the hanger ball. Pull the hanger ball up
tight against the pin and securely tighten the setscrew
in the hanger ball. A loose setscrew could create fan
wobble.
HANGER BALL
PIN
CEILING COVER
DOWNROD
SETSCREW
7. The fan comes with blue, black and white leads
that are 80” long. Before installing fan, measure up
approx-imately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
8. Turn fan motor assembly upside down in
preparation for mounting fan blades. Position the
top and bottom halves of the styrofoam packaging
on end, with solid styrofoam facing outward. Set
side-by-side on the floor with a six to eight-inch gap
between the halves (Figure 5). Carefully place the
partially assembled ceiling fan on the styrofoam
halves, with the hanger ball/downrod assembly
positioned in the gap and the fan motor assembly
resting on top of the styrofoam ends.
Figure 4
PARTIALLY
ASSEMBLED
FAN
SOLID
STYROFOAM
FACING OUT
6" - 8"
GAP
Figure 5
5
Model No.: CF990
How to Put Your Ceiling Fan Together (continued)
8. Remove and discard the four rubber shipping
retainers securing the motor hub in the motor
housing assembly (Figure 6).
9. Position one blade medallion onto the blade.
Place the blade flange to the other side of the
blade to secure the medallion and blade to the
flange. Mount the medallion, fan blade, and blade
flange using the three #10-32 x 12.3mm washer
head blade screws (Figure 7).
MOTOR
HOUSING
ASSEMBLY
10. Slide the blade assembly into the housing slot.
Attach the blade assembly using two 1/4” x 1/2”
round head lock tie flange screws. Attach the
remaining four blades (Figure 8).
Figure 6
RUBBER
SHIPPING
RETAINERS
NOTE: Take care not to scratch fan housing when
installing blades.
BLADE
MEDALLION
FAN BLADE
BLADE
FLANGE
#10-32 x12.3mm WASHER
HEAD BLADE SCREW (3)
Figure 7
1/4" x 1/2" ROUND HEAD LOCK
TIE FLANGE SCREWS (2)
BLADE ASSEMBLY
Figure 8
6
Model No.: CF990
How to Put Your Ceiling Fan Together (continued)
11. Remove one #8-32 x 10mm serrated head screw
from the fan motor housing (reserve for later
use). Loosen the other two screws to assemble
the lower housing to the fan motor housing
(Figure 9).
#8-32 x 10mm
SERRATED HEAD SCREWS (3)
LOWER HOUSING
12. Position the lower housing onto the fan motor
assembly, aligning each of the the three holes.
Attach the lower housing to the fan motor
assembly using the three #8-32 x 10mm serrated
head screws. Rotate the lower housing to
securely tighten by engaging the screws in the
two key hole slots (Figure 9).
NOTE: Make sure wires are not pinched between
fan motor assembly and lower housing.
Figure 9
13. Attach the white wire connector from the ceiling
fan to the white wire connector of the light kit
assembly (Figure 10). Connect the black wire
connector from the ceiling fan to the black wire
connector of the light kit assembly.
LIGHT KIT ASSEMBLY
LIGHT KIT ASSEMBLY WHITE
WIRE CONNECTOR
CEILING FAN WHITE WIRE
CONNECTOR
14. Remove one of the one of the three screws in the
lower housing and loosen the remaining two
screws (Figure 11).
NOTE: Make sure all wires and connector are
tucked under the light kit assembly and not
pinched between light kit assembly and lower
housing.
CEILING FAN BLACK WIRE
CONNECTOR
LIGHT KIT ASSEMBLY BLACK
WIRE CONNECTOR
Figure 10
15. Position the light kit assembly onto the lower
housing, aligning each of the the three holes.
Attach the light kit assembly to the lower housing,
using three #8-32 x 10mm serrated head screws.
Rotate the light kit assembly to securely tighten
by engaging the screws in the two key hole slots
(Figure 11).
LOWER
HOUSING
#8-32 x 10mm SERRATED
HEAD SCREW (3)
LIGHT KIT ASSEMBLY
Figure 11
7
Model No.: CF990
How to Hang Your Ceiling Fan
!
WARNING
CEILING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
AT LEAST
7'
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan, light kit or receiver.
!
WARNING
FLOOR
Figure 12
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 12).
!
WARNING
NOTE: CEILING COVER
OMITTED FOR CLARITY.
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of 15.9
kg. (35lbs.) or less”.
!
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
WARNING
HANGER
BRACKET
To reduce the risk of fire, electrical shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 15.9 kg. (35lbs.) or less”, and use screws
supplied with outlet box. Most outlet boxes commonly
used for support of light fixtures are not acceptable for
fan support and may need to be replaced. Consult a
qualified electrician if in doubt.
TAB
Figure 13
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
1.Disconnect electrical power to the branch circuit at
the circuit breaker or fuse box before attempting to
install the ceiling fan wall control into the outlet box.
OUTLET
BOX
2.Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 13.)
3. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 13). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 14).
!
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
WARNING
Figure 14
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
!
1-1/4" THREADED
STUD (2)
!
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
8
Model No.: CF990
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
SUPPLY BLACK
WIRE (HOT)
WARNING
AC I N
RECEIVER
BLACK WIRE
GROUND WIRE
FAN
YELLOW
WIRE
FAN BLACK
WIRE
ANTENNA
GREEN GROUND
WIRE FROM
HANGER BRACKET
1. Disconnect electrical power to the branch circuit at
the circuit breaker or fuse box before attempting to
install the ceiling fan wall control into the outlet box.
TO
M
AC IN L
OTO
RL
RECEIVER
BLUE WIRE
GREEN GROUND
WIRE FROM
HANGER BALL
TO MO
TOR N
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
FAN BLUE WIRE
FAN WHITE WIRE
RECEIVER WHITE
WIRE
1-1/4" THREADED
STUD (2)
Figure 15
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan, light kit or receiver.
STANDARD ON-OFF
WALL SWITCH
2. Position the supply wires to the left side of the
outlet box (Figure 15); position the fan wires to the
right side. Partially insert the remote control
receiver (flat side up) until one end rests on the
hanger ball as shown in Figure 15.
TO 120VOLT
SUPPLY
BLACK
BLACK
BLACK (HOT)
WHITE
WHITE
WHITE
GROUND
NOTE: Make all wiring connections using wire
connectors (supplied). Make sure that all
connections are tight, including ground, and that
no bare wire is visible at the wire connectors,
except for the ground wire.
RED
TWO-CONDUCTOR
CABLE (WITH GROUND)
GREEN WIRE (GROUND)
FROM HANGER BALL
AND HANGER BRACKET
YELLOW
BLUE
WHITE
BLACK
BLUE
WHITE
HANGER BALL
Figure 16
3. Refer to Figure 15 and 16 and connect the receiver
wires to the supply wires and the fan motor wires
as follows:
a. Securely connect the green grounding wires from
the hanger ball and the hanger bracket to the
supply grounding conductor (this may be a bare
wire or a wire with green insulation).
b. Securely connect the supply white (neutral) wire to
the receiver white (AC IN N) wire.
c. Securely connect the supply black wire (hot) wire to
the receiver black (AC IN L) wire.
d. Securely connect the fan motor white wire to the
receiver white (TO MOTOR N) wire.
e. Securely connect the fan motor black wire to the
receiver black (TO MOTOR L) wire.
f. Securely connect the fan motor blue wire to the
receiver blue (FOR LIGHT) wire.
g. If installing the optional accessory AL100 accent
light, follow the AL100 installation instructions.
!
RECEIVER WHITE
WIRE
RECEIVER BLACK
WIRE
FOR LIG
HT
!
SUPPLY WHITE WIRE
(NEUTRAL)
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
9
Model No.: CF990
How to Wire Your Ceiling Fan (continued)
4. Push the wires and connectors up into the outlet
box while inserting the receiver fully into the hanger
bracket. Position the antenna wire on top of the
receiver.
5. Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket.
CEILING COVER
6. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 17).
THREADED STUDS (2)
LOCKWASHERS (2)
7. Secure the ceiling cover in place by sliding
KNURLED KNOBS (2)
Figure 17
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
Installation of Lower Light Glass
1. Screw two 50-watt (maximum) halogen mini
candelabra base bulbs into the light kit assembly
sockets (Figure 18).
2. Unscrew the finial nut from the light kit assembly
threaded nipple (Figure 18).
3. Position the glass shade over the threaded nipple
on the light kit assembly.
50-WATT
HALOGEN
LIGHT BULB (2)
LIGHT
SOCKET (2)
THREADED
NIPPLE
4. Reinstall the finial nut onto the threaded nipple.
NOTE: Periodically check that the glass bowl is
seated correctly in the light kit assembly and the
finial nut is securely fastened.
5. Assembly of the ceiling fan is now complete.
Restore electrical power to the branch circuit at the
fuse box or breaker panel.
GLASS SHADE
Figure 18
REVERSING
SWITCH
FINIAL NUT
MOTOR
HOUSING
Figure 19
10
Model No.: CF990
Remote Control Procedures
General
Your Emerson Ceiling Fan/Light Remote Control
consists of hand-held transmitter and a receiver which
is mounted under the fan ceiling cover. The remote
control is designed to separately control your ceiling
fan speed and light intensity. There are four push
buttons (., .., ..., ....) to set the fan speed and turn
the fan off. The light ( ) push button turns the light
on and off and controls the light intensity. The blue
indicator light will illuminate while any button is
pressed, indicating that the battery is good.
REMOTE CONTROL
LEVERS
ON
1
2
3
4 5
I
TWO AAA
BATTERIES
CODE
SWITCHES
The remote control transmitter is powered by two
AAA alkaline batteries (not included). To prevent
possible damage if the batteries should leak, be sure
to remove the batteries when the control is not to be
used for an extended period of time.
Code switches in the transmitter may be set in 32
different positions. If your fan and light go on and off
without using your control, you may be getting
interference from other remote units such as garage
door openers, car alarms or security systems. To
remedy this situations, simply change the
combination code in your transmitter.
Figure 20
BATTERY
COMPARTMENT
COVER
REMOTE CONTROL
Programming The Receiver
1.Restore electrical power to the branch circuit at the
circuit breaker or fuse panel.
2.Turn the wall switch "On".
3.Within 1 minute of restoring electricity, push and
hold the "Off" (
) button for 3-5 seconds to
program the receiver with the transmitter code.
If turned on, the fans lights will blink when the code
is set.
Preset Memory Feature
Your Emerson receiver is equipped with a preset
memory feature. If the AC supply to the receiver is
powered through a wall switch, when the switch is
turned OFF, the control will remember the light
intensity and fan speed. When the switch is turned
back ON the light and fan will resume operation as
they we re prior to the switch being turned OFF.
4.Proceed to the next section to learn how to operate
your ceiling fan.
Installation of Battery
1.Remove the battery cover by pressing firmly below
the arrow and sliding the cover off the control
(Figure 20).
2.Remove the connector from the battery
compartment and install two AAA alkaline batteries.
Setting Operating Frequency of
Transmitter
Your remote control transmitter has code switches
which must be set in one of 32 possible code
combinations. The five levers (numbered 1, 2, 3, 4,
and 5) on the switches are factory-set in the ON (up)
position. Do not use this setting. Change the switch
settings as follows:
1.Slide the five switch levers in the remote control
(transmitter) to your choice of ON (up) or down
positions. Use a ball-point pen or small screwdriver
and slide the levers firmly up or down.
2.The sixth switch marked ON and I is for dimming
control of lights: Set switch to ON to allow for
dimming of the lights. Set switch to I for no dimming
of the lights such as for fluorescent bulbs.
3. Reinstall the transmitter battery cover.
11
Model No.: CF990
Using Your Fan
IMPORTANT
Fan installation must be completed, including the
installation of the fan blades, before testing of the
remote control.
COVER
WALL
BRACKET
SCREW
HOLES (2)
Your remote control has full control of your fan and
light (Figure 21).
1.To set the desired fan speed, press one of the four
buttons (., .., ..., ....) to operate your fan from low to
high speeds.
TO INSTALL
BRACKET TO WALL:
SLIDE THE COVER
UP TO EXPOSE THE
SCREW HOLES FOR
INSTALLATION
POWER INDICATOR
LIGHT
FAN BUTTON
2.To turn the downlight on, press and release the
(
) button. The light will turn on at the light
intensity previously selected.
HIGH TO LOW
BUTTONS
3.To vary the intensity of the light, hold the (
)
button down until the desired light intensity is
reached, then release the button.
LIGHT BUTTON
Note: When turning the light on, light will turn on
at the light intensity previously selected.
STORAGE
BRACKET
4.If airflow is desired in the opposite direction, turn
the fan off and wait for the blades to stop turning.
Then slide the reversing switch, located on top of
the fan motor assembly, to the opposite position
(Figure 19) and turn the fan on again. The blades
will turn in the opposite direction and reverse the
airflow.
Figure 21
Installation of Storage Bracket
A storage bracket is provided for holding your remote
control when not in use (Figure 21). If you desire to
use the bracket. Install it on a wall that is away from
excess heat or humidity.
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
!
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Accessories
1. Ceiling Fan/Light Controls (see store or catalog).
!
2. Downrod Extension Kits (see store or catalog).
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
12
Model No.: CF990
Trouble Shooting
!
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan.
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
1. Check main and branch circuit fuses or circuit
breakers.
2. Loose power line connections to the fan,
or loose switch wire connections in the
switch housing.
2. Check line wire connections to fan and switch
wire connections in the switch housing.
WARNING: Make sure main power is
!
turned OFF.
3. Dead battery in remote control transmitter.
3. Replace battery (red indicator light on transmitter
should light when any button is pressed).
4. See Remote Programming Procedures, page 9.
4. Remote control transmitter not programmed
to match control receiver.
2. Fan sounds noisy.
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Loose screws in motor housing.
2. Check to make sure all screws in motor housing
are snug (not over-tight).
3. Wire connectors inside switch housing
rattling.
3. Check to make sure wire connectors in switch
housing are not rattling against each other or
against the interior wall of the switch housing.
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is
turned OFF.
4. Screws holding blades to flywheel
are loose.
4. Tighten screws securely.
1. Setscrew in motor coupling is loose.
1. Tighten both setscrews securely in the motor
coupling.
2. Setscrew in hanger ball/downrod
assembly is loose.
2. Tighten the setscrew in the hanger ball/
downrod assembly.
3. Screws securing fan blade flanges to
flywheel are loose.
3. Check to be sure screws which attach the fan
blade flanges to the motor are tight.
4. Hanger bracket and/or ceiling outlet
box is not securely fastened.
4. Tighten the hanger bracket screws to the outlet
box, and/or secure outlet box.
5. Fan blades out of balance.
5. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
13
Model No.: CF990
Repair Parts
2
1
4
7
3
12
13
8
9
23
14
6
24
15
5
10
20
11
16
21
22
17
18
19
14
Model No.: CF990
Repair Parts Listing
Key
No.
*
Model Numbers
CF990BS00
CF990VNB00
Description
1
2
3
Hanger Ball Assembly,
Consisting of:
Hanger Bracket
Hanger Ball
Downrod (4.5”)
761655-17
761655-89
—
—
—
—
—
—
*
4
5
6
7
8
9
10
11
12
Parts Bag Containing:
Wire Connector (3)
Pin, Clevis (1)
Clip, Hairpin (1)
Threaded Stud, #8-32 x 1-1/4” (2)
Lockwasher, External Tooth #8 (2)
Knurled Knob, #8-32 (2)
Screw, Washer Head, #10-32 x 12.3mm (16)
Screw, Round Head Lock Tie Flange, 1/4” x 1/2” (11)
Balancing Kit (1)
764286
—
—
—
—
—
—
—
—
—
764286-1
—
—
—
—
—
—
—
—
—
13
Canopy, Ceiling (1)
764267-BS
764267-VNB
14
Motor Coupling Cover (1)
764268-BS
764268-VNB
15
Harness Wiring (1)
764285-1
764285-2
16
Lower Housing Assembly (1)
764280-BS
764280-VNB
17
Light Kit Assembly (1)
764281-WW
764281-WW
18
Light Kit Glass (1)
764283-OM
764285-VC
19
Finial Nut (1)
764284-BS
764284-VNB
20
Blade Flange (set of 5)
764274-BS
764274-VNB
21
Blades (set of 5)
764278-DM
764278-WA
22
Blade Medallions (set of 5)
764276-BS
764276-VNB
23
Receiver, Remote Control (1)
RCFP
RCFP
24
Transmitter (1)
SR400
SR400
—
Owner's Manual
BP7464
BP7464
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION •
NAME OF ITEM •
MODEL NUMBER
For repair parts, phone 1-800-654-3545.
15
Model No.: CF990
Emerson Air Comfort Ceiling Fan Limited Warranty
What The Limited Warranty Covers:
This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original retail
purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and accessories of the
Emerson Ceiling Fan against all defects in workmanship and materials.
What The Period Of Coverage Is:
This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner's Manual
or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are covered by this limited
warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE OR PROVINCE SHALL COVER THE
MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TO COMPONENTS AND ACCESSORIES.
No Other Express or Implied Warranty Applies:
THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILING FAN, AND
ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE, WHETHER OR NOT
THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED OR MANUFACTURED FOR YOUR USE OR
PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THE ONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS
AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING
FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIME OF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN
REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROM STATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU.
What We Will Do To Correct Problems:
If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during the
expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or workmanship, you
must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defective motor, component or other
accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and no replacement Emerson Ceiling Fan
can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or the replacement Emerson Ceiling Fan to you at
no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan.
How You Can Receive Warranty Service:
You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You can return your
Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at 1-800-237-6511 to obtain a return authorization and service identification tag. In
order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have that information readily available
when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call Emerson Customer Service, prior to your call please
be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your return authorization request, we will provide you with a postage
paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed at the end of this limited warranty. The return label will be sent to
the mailing address you provide to us by phone.
What Is Not Covered:
This limited warranty does not extend to and expressly excludes:
• The glass globes and light bulbs of your Emerson Ceiling Fan,
• Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship,
• Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center, use of
parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse, modifications
or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession,
• Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual.
This limited warranty is deemed null and void upon the occurrence of either of the following events:
• You cease to own the Emerson Ceiling Fan product, or
• The Emerson Ceiling Fan is moved from its original point of installation.
This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent, dealer
or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co.
Limitation of Liability
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BY LAW, IN
NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES,
INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILING FAN OR FOR THE
NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO
EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER
TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANY INDIVIDUAL USING THE EMERSON CEILING FAN
EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequential damages" shall include, but not be limited to, loss of
anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or equipment.
How State and Provincial Law Relates To The Warranty:
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you. This
limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP74640000
Printed in China 11/12
Form No. BP7464
Model No.: CF990