Mazda 2002 Tribute User manual

Add to my manuals
2 Pages

advertisement

Mazda 2002 Tribute User manual | Manualzz

REV.050614

BEEMZ-30

IMPORTANT: NOT COMPATIBLE

WITH PREMIUM SOUND SYSTEMS

(AMPLIFIED SYSTEMS)

APPLICATIONS

Mazda

2011 - 2012 Mazda2

2004 - 2011 Mazda3

2012 - 2014 Mazda3*

2006 - 2010 Mazda5

2012 - 2014 Mazda5*

2003 - 2011 Mazda6

2006 - 2011 MX-5 Miata

2004 - 2011 RX-8

2002 - 2006 MPV

2007 - 2011 Speed3

2006 - 2007 Speed6

2007 - 2011 CX-7

2007 - 2011 CX-9

2008 - 2011 Tribute

Notes:

*Important: These applications require the installer to place a Diode on the

24-Pin White harness, from the Crux

T-Harness. See slip sheet included in the Manual for further information & instructions.

**2008-2010 Tribute requires a different harness: Crux Part Number 3196; must be special ordered.

BLUETOOTH INTERFACE FOR SELECT 2002-UP MAZDA VEHICLES

work. Following these instructions from “Start” to” Finish” will ensure

9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PRELIMINARY:

- Disconnect the positive(+) battery cable for radios that are

non-navigation. Radios that are navigation ready should not

disconnect the battery cable. Please use caution when installing.

Do not install the interface near or on the vehicle’s HVAC system.

This will prevent overheating and condensation build up.

Use overview to help you determine installation method.

INSTALLATION

1. Remove the factory radio to gain access to the factory radio wiring

connectors.

2. Disconnect the factory connectors from the rear of the factory radio.

3. Connect the male connectors of the interface power harness into the

factory radio.

4. Reconnect the factory connectors into the mating connectors of the

interface harness.

5. Connect the male 3-pin connector into the pigtail connector.

6. Route the microphone to a desired location, (for example near the

rear view mirror).

7. Re-install a factory radio back into the vehicle’s dash.

FIG. 1 (Multi-PIN CONNECTORS):

TO FACTORY

HARNESS

MIC

BALL JOINT

TO FACTORY

RADIO

MOUNTING THE MICROPHONE

1. Insert the mounting clip into the ball joint on the microphone.

2. Mount the clip on your visor or near the rear view mirror.

3. Route the remaining cable along the edge of the roof liner and

towards the back of the radio, hiding the cable from sight.

INITIAL PAIRING TO THE VOICE PROMPTS:

1. READY (POWER ON)

2. SEARCHING PHONES (FOR PREVIOUS PAIRED PHONES)

3. PLEASE SEARCH AND SELECT THE “BEE LINE” DEVICE FROM

MOBILE PHONE AND ENTER “0000”.

4. YOU ARE NOW READY TO USE THE HF SYSTEM.

Note: The Bluetooth interface will remember up to the last 8 devices.

power back on to re-attempt, if unsuccessful please contact our tech support line.

AUTO RE-CONNECT:

1. The BEEMZ-30 module will automatically re-connect the a previously

paired mobile phone when the ignition is turned “ON” to the vehicle

and the mobile phone’s Bluetooth feature is also on.

Note: The Bluetooth module will re-connect with the last mobile phone’s it was paired with. If no mobile phone is not found, it will revert to the pairing process.

SUPPORTED RADIOS

SEEK

APC

VOL

PUSH POWER

FM1/2 AM CD MD/TAPE CLOCK

H M

LOAD

WMA FM1/2 AM SIRIUS

FOLDER

FOLDER

DISP

DISC

CAT

DISC

CAT

PUSH

TEXT/ESN AUTO-M

CD

SCAN

AUX

SCAN

AUTO-M

PUSH

TUNE

AUDIO CONT.

MP3

:00

Note: If an incoming call is answered from the mobile phone’s keypad, the call will direct itself to the headset on the mobile phone. To re-direct the phone call to the Crux interface, it must be done directly from the mobile phone.

Note: When transferring a phone call to the mobile phone for privacy, the user must re-connect the Crux interface and the mobile phone by selecting the module from the device menu on the phone.

Note: If after ending a call the radio is powered “OFF”, you must power

“ON” the radio to regain volume control.

TRACK

APC

TRACK/SEEK

REPLAY

AUTO-M

TEXT

SCAN

FM1/2

1 2

AM SAT

3 4

CD MEDIA

5 6

LOAD

1 2

PUSH

POWER

VOLUME

SCAN

AUTO

FM

CD

AUX

AM

4 5

DISP/ESN

PUSH

AUDIO CONT

TUNE

RDM

H M 00

RPT

USING THE STEERING WHEEL CONTROL BUTTONS

VOICE DIAL

ANSWER

END A CALL

REJECT

HOLD SEEK DN FOR 2 SECONDS

PRESS SEEK UP BUTTON ONCE

PRESS SEEK DN BUTTON ONCE

PRESS SEEK DN BUTTON ONCE

ANSWER SECOND CALL PRESS SEEK UP BUTTON ONCE

SWITCH BETWEEN CALLS PRESS SEEK UP BUTTON ONCE

INCREASE VOLUME

DECREASE VOLUME

PRIVACY MODE

PRESS VOLUME UP ONCE

PRESS VOLUME DN ONCE

PRESS SEEK UP ONCE

Note: Premium Audio Systems need to “Turn On” the radio for handsfree audio to be heard.

All features of this module may vary by mobile phone manufacturer. For questions on your mobile phone’s features, please reference the mobile phone’s user manual for information.

BLUETOOTH INTERFACE FOR SELECT 2002-UP MAZDA VEHICLES

BEEMZ-30

IMPORTANT: NOT COMPATIBLE

WITH PREMIUM SOUND SYSTEMS

(AMPLIFIED SYSTEMS)

APPLICATIONS

Mazda

2011 - 2012 Mazda2

2004 - 2011 Mazda3

2012 - 2014 Mazda3*

2006 - 2010 Mazda5

2012 - 2014 Mazda5*

2003 - 2011 Mazda6

2006 - 2011 MX-5 Miata

2004 - 2011 RX-8

2002 - 2006 MPV

2007 - 2011 Speed3

2006 - 2007 Speed6

2007 - 2011 CX-7

2007 - 2011 CX-9

2008 - 2011 Tribute

Notes:

*Important: These applications require the installer to place a Diode on the

24-Pin White harness, from the Crux

T-Harness. See slip sheet included in the Manual for further information & instructions.

**2008-2010 Tribute requires a different harness: Crux Part Number 3196; must be special ordered.

USING THE MENU STRUCTURE:

To enter the Voice Menu you must do the following:

1. Hold Seek Down fro 2 seconds.

3. Hold Seek Down fo 2 seconds.

You are now at the top of the menu.

4. Press Seek Down to scroll though the menu options.

5. Press Seek Up to select a menu option.

MISSED CALLS:

Continue to press the “SEEK DN” button till you hear the

interface announce “MISSED CALLS”, and wait for the numbers

to be announced.

3. When the number you wish to dial is announced, press the

“SEEK UP” button once to make the call.

INCOMING CALLS:

Continue to press the “SEEK DN” button till you hear the

interface announce “INCOMING CALLS”, and wait for the

numbers to be announced.

3. When the number you wish to dial is announced, press the

“SEEK UP” button once to make the call.

OUTGOING CALLS:

Continue to press the “SEEK DN” button till you hear the

interface announce “OUTGOING CALLS”, and wait for the

numbers to be announced.

3. When the number you wish to dial is announced, press the

“SEEK UP” button once to make the call.

SETTING TTS VOLUME:

Continue to press the “SEEK DN” button twice till you hear the

interface announce “SETTING VOLUME”, and wait for her

announcement.

3. Set the TTS volume by pressing the volume Vol+ and Vol- waiting

for the announcement. Each announcement will indicate the volume

level of the TTS.

4. When the desired volume level is reached, press the “SEEK UP”

button once to select.

DELETE ALL PAIRED DEVICES:

This feature allows you to delete all paired devices on the interface.

The module does NOT allow the user to only clear one device. The module will delete all previously paired devices only

Continue pressing the “SEEK DN” button twice till you hear the

interface announce “DO YOU WANT TO DELETE PAIRED

PHONE LIST”.

4. The interface will ask “ARE YOU SURE”, press the “SEEK UP”

HF

VOL +

-

+

VOL

-

MODE

MODE

VOL +

-

MODE

MODE

Have a bad connection when using the A2DP or Handsfree

Are you experiencing random static interuptions durring your phone calls?

Have you paired your mobile device, and get no sound from the radio? Try reseting the TTS volume setting.

Note: The menu structures only remember the last 24 numbers in the call log from dialed from the mobile phone.

Note: All menu structures work in 3 second increments.

If after 3 seconds the interface will time-out.

Delete all paired devices on your mobile device and on the UBT.

(See Using The Menu Structure)

Remove the battery on the mobile device for a minimum of

15 Seconds.

With the phone paired to the

UBT, enter the “SETTING TTS

VOLUME” under menu structure.

The default level is at volume 4.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement