HP 6830s - Notebook PC Maintenance and Service Guide

Add to my manuals
147 Pages

advertisement

HP 6830s - Notebook PC Maintenance and Service Guide | Manualzz

HP Compaq 6830s Notebook PC

Maintenance and Service Guide

© Copyright 2008 Hewlett-Packard

Development Company, L.P.

Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard

Company under license. Intel, Core, Celeron are trademarks of Intel Corporation in the

United States and other countries. Microsoft,

Windows, and Windows Vista are U.S.

registered trademarks of Microsoft

Corporation. SD Logo is a trademark of its proprietor.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

First Edition: July 2008

Document Part Number: 482365-001

Safety warning notice

WARNING!

To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the

AC adapter comply with the user-accessible surface temperature limits defined by the International

Standard for Safety of Information Technology Equipment (IEC 60950).

iii

iv Safety warning notice

Table of contents

1 Product description

2 External component identification

Top components ................................................................................................................................... 7

Display components ............................................................................................................ 7

Wireless antennae (select models only) .............................................................................. 7

TouchPad ............................................................................................................................ 8

Buttons, switch, lights, and speakers ................................................................................. 10

Keys ................................................................................................................................... 11

Front components .............................................................................................................................. 12

Right-side components ....................................................................................................................... 12

Left-side components ......................................................................................................................... 13

Bottom components ........................................................................................................................... 14

3 Illustrated parts catalog

Serial number location ........................................................................................................................ 15

Computer major components ............................................................................................................. 16

Plastics Kit .......................................................................................................................................... 22

Cable Kit ............................................................................................................................................. 23

Mass storage devices ......................................................................................................................... 24

Miscellaneous parts ............................................................................................................................ 25

Sequential part number listing ............................................................................................................ 27

4 Removal and replacement procedures

Preliminary replacement requirements ............................................................................................... 32

Tools required .................................................................................................................... 32

Service considerations ....................................................................................................... 32

Plastic parts ....................................................................................................... 32

Cables and connectors ..................................................................................... 33

Drive handling ................................................................................................... 33

Grounding guidelines ......................................................................................................... 34

Electrostatic discharge damage ........................................................................ 34

Packaging and transporting guidelines ............................................. 35

v

Workstation guidelines ..................................................................... 35

Equipment guidelines ....................................................................... 36

Unknown user password ................................................................................................... 37

Component replacement procedures ................................................................................................. 38

Serial number .................................................................................................................... 38

Computer feet .................................................................................................................... 39

Battery ............................................................................................................................... 40

Hard drive .......................................................................................................................... 41

WLAN module .................................................................................................................... 43

Memory module ................................................................................................................. 45

Optical drive ....................................................................................................................... 47

Switch cover and keyboard ................................................................................................ 49

Speakers ............................................................................................................................ 54

Display assembly ............................................................................................................... 55

Top cover ........................................................................................................................... 60

USB board ........................................................................................................................ 63

Bluetooth module ............................................................................................................... 64

RTC battery ....................................................................................................................... 66

System board ..................................................................................................................... 68

Fan ..................................................................................................................................... 70

Modem module .................................................................................................................. 72

Heat sink ............................................................................................................................ 74

Processor ........................................................................................................................... 76

5 Computer Setup

Starting Computer Setup .................................................................................................................... 78

Using Computer Setup ....................................................................................................................... 79

Navigating and selecting in Computer Setup ..................................................................... 79

Restoring factory settings in Computer Setup ................................................................... 79

Computer Setup menus ..................................................................................................................... 80

File menu ........................................................................................................................... 80

Security menu .................................................................................................................... 81

Diagnostics menu .............................................................................................................. 81

System Configuration menu .............................................................................................. 82

6 Specifications

Computer specifications ..................................................................................................................... 84

17.0-inch, WXGA+WVA display specifications .................................................................................. 85

Hard drive specifications .................................................................................................................... 86

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer specifications .......................... 87

DVD±RW SuperMulti Double-Layer Combo Drive specifications ...................................................... 88

DVD/CD-RW Combo Drive specifications .......................................................................................... 89

DVD-ROM Drive specifications .......................................................................................................... 90

vi

System DMA specifications ................................................................................................................ 91

System interrupt specifications ........................................................................................................... 92

System I/O address specifications ..................................................................................................... 93

System memory map specifications ................................................................................................... 95

7 Screw listing

Phillips PM2.0×2.0 broad-head screw ................................................................................................ 97

Phillips PM2.0x2.0 broad-head screw ................................................................................................ 98

Phillips PM2.0×3.0 screw ................................................................................................................... 99

Phillips PM2.0x4.0 screw ................................................................................................................. 100

Phillips PM2.5×4.0 screw ................................................................................................................. 101

Phillips PM2.5×4.0 screw ................................................................................................................. 102

Phillips PM2.5×6.0 captive screw ..................................................................................................... 104

Phillips PM2.5×9.0 screw ................................................................................................................. 105

Phillips PM2.5×10.0 captive screw ................................................................................................... 106

Phillips PM2.5x10.0 captive screw ................................................................................................... 107

Phillips PM3.0×4.0 screw ................................................................................................................. 107

Slotted Torx ST8M2.5×7.0 screw ..................................................................................................... 108

Torx T8M2.5×5.0 broad-head screw ................................................................................................ 110

Torx T8M2.5×4.0 screw ................................................................................................................... 111

Torx T8M2.5×6.0 screw ................................................................................................................... 111

Slotted Torx T8M2.0x2.0 screw ........................................................................................................ 114

Slotted Torx T8M2.5x10.0 screw ...................................................................................................... 115

8 Backup and recovery

Backup and recovery in Windows Vista ........................................................................................... 116

Overview .......................................................................................................................... 116

Backing up your information ........................................................................................... 116

Performing a recovery .................................................................................................... 117

Using the Windows recovery tools ................................................................................... 118

Using f11 .......................................................................................................................... 118

Using a Windows Vista operating system DVD (purchased separately) ......................... 119

Backup and recovery in Windows XP .............................................................................................. 120

Overview .......................................................................................................................... 120

Backing up your information ........................................................................................... 120

Performing a recovery .................................................................................................... 121

Recovering your information ........................................................................... 121

Recovering the operating system and programs ............................................ 121

9 Connector pin assignments

Audio-in (microphone) ...................................................................................................................... 122

Audio-out (headphone) ..................................................................................................................... 123

External monitor ............................................................................................................................... 124

vii

RJ-11 (modem) ................................................................................................................................ 125

RJ-45 (network) ................................................................................................................................ 126

Universal Serial Bus ......................................................................................................................... 126

10 Power cord set requirements

Requirements for all countries and regions ...................................................................................... 127

Requirements for specific countries and regions ............................................................................. 128

11 Recycling

Battery .............................................................................................................................................. 129

Display .............................................................................................................................................. 129

Index ................................................................................................................................................................. 135

viii

1 Product description

Category

Product Name

Processors

Chipset

Graphics

Panels

Memory

Description

HP Compaq 6830s Notebook PC

Intel® Core™2 Duo processors

● T5670 1.80-GHz processor, 2-MB L2 cache, 800-MHz front side bus (FSB)

● T5870 2.0-GHz processor, 2-MB L2 cache, 800-MHz FSB √

● P8400 2.26-GHz processor, 3-MB L2 cache, 1066-MHz FSB √

● P8600 2.40-GHz processor, 3-MB L2 cache, 1066-MHz FSB √

● T9400 2.53-GHz processor, 6-MB L2 cache, 1066-MHz FSB √

Intel Celeron® M processors

● 575 2.0-GHz processor, 1-MB L2 cache, 667-MHz FSB

● 585 2.16-GHz processor, 1-MB L2 cache,667-MHz FSB

Northbridge: Intel PM45 with up to 1066-MHz FSB

Southbridge: Intel ICH9M

√ ATI-M82SE discrete graphics subsystem memory with

Hypermemory support

All display assemblies include 2 wireless local area network

(WLAN) antennae

● 17.0-inch WXGA BrightView

● 17.0-inch WXGA+

● 17.0-inch WSXGA+WVA

2 customer-accessible/upgradable memory module slots

Supports dual-channel memory

Supports up to 8 GB of system RAM

Computer models equipped with PM45 system board

1

Category

Hard drives

Description

Supports the following configurations in all countries and regions except Brazil:

● 8192-MB total system memory (4096 x 2, dual-channel)

● 4096-MB total system memory (4096-MB x 1, dual-channel)

● 4096-MB total system memory (2048 × 2, dual-channel)

● 3072-MB total system memory (2048 + 1024, dual-channel)

● 2048-MB total system memory (1024 × 2, dual-channel)

● 2048-MB total system memory (2048 × 1)

● 1024-MB total system memory (1024 × 1)

Supports the following configurations only in Brazil:

● 3072-MB total system memory (2048 + 1024, dual-channel)

● 2048-MB total system memory (2048 × 1)

● 2048-MB total system memory (1024 × 2, dual-channel)

● 1024-MB total system memory (1024 × 1)

PC2-5300, 800–MHz, DDR2

Supports the following configurations in all countries and regions except Brazil:

● 8192-MB total system memory (4096 x 2, dual-channel)

● 4096-MB total system memory (4096 x 1, dual-channel)

● 4096-MB total system memory (2048 x 2, dual-channel)

● 3072-MB total system memory (2048 + 1024, dual-channel)

● 2048-MB total system memory (2048 x 1)

● 2048-MB total system memory (1024 x 2, dual-channel)

● 1024-MB total system memory (1024 x 1)

Supports the following configurations only in Brazil: √

● 3072-MB total system memory (2048 + 1024, dual-channel)

● 2048-MB total system memory (2048 x 1)

● 2048-MB total system memory (1024 x 2, dual-channel)

● 1024-MB total system memory (1024 x 1)

Supports 9.5-mm, 2.5-inch hard drives

Customer-accessible

Serial ATA

Computer models equipped with PM45 system board

2 Chapter 1 Product description

Category

Optical drives

Diskette drive

Audio

Modem

Ethernet

Wireless

Description

Supports full disk encryption

Supports HP 3D DriveGuard

Supports the following drives:

● 320-GB, 5400-rpm hard drive

● 250-GB, 5400-rpm hard drive

● 160-GB, 5400-rpm hard drive

● 120-GB, 5400-rpm hard drive

● 120-GB, 7200-rpm hard drive

Fixed (removal of 1 screw required)

Customer-accessible

Serial ATA

12.7-mm tray load

Supports the following optical drives:

● DVD±RW SuperMulti Double-Layer Drive with LightScribe

● Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-

Layer

● DVD/CD-RW Combo Drive

● DVD-ROM Drive

Supports external USB diskette drive only

Supports boot from external USB diskette drive

Supports 3-mode diskette drive

HD audio - ADI1984

56K V.92 1.5-inch data/fax modem with digital line guard

Marvell 10/100/1000 Ethernet 88E8072–B1

S3/S4/S5 wake on LAN: DC - no

S3/S4/S5 wake on LAN: AC - yes

Integrated WLAN options by way of wireless module:

2 WLAN antennae built into display assembly

Support for no-WLAN option

Support for the following WLAN formats:

● Intel 802.11a/b/g/n

● Broadcom 802.11a/b/g/n

Computer models equipped with PM45 system board

3

Category

External media card

Ports

Keyboard/pointing devices

Power requirements

Security

Operating system

Description Computer models equipped with PM45 system board

● Broadcom 802.11b/g

● Intel 802.11a/b/g

Integrated personal area network (PAN) options by way of Bluetooth® module:

Support for no-WPAN option

Broadcom Bluetooth 2.0+EDR

One ExpressCard/54 slot √

Media Card Reader supporting Secure Digital (SD) Memory Card,

Memory Stick, Memory Stick Pro, Memory Stick Duo,

MultiMediaCard (MMC), and xD–Picture Card formats

Audio-in (stereo microphone)

Audio-out (stereo headphone)

RJ-11 (modem)

RJ-45 (Ethernet, includes link and activity lights)

USB (4) √

VGA (Dsub 15-pin) supporting 1600 × 1200 external resolution at

75-Hz (hot plug/unplug with auto-detect)

Headphone/Line Out

3-pin AC power adapter

11.97-inch keyboard with integrated numeric keypad

2–way scrolling, taps enabled as default

TouchPad only, with 2 TouchPad buttons

90-W HP Smart AC adapter with localized cable plug support (3wire plug with ground pin, supports 3-pin DC connector)

8-cell, 63-Wh Li-ion battery

6-cell, 47-Wh Li-ion battery

6-cell 55-Wh Li-ion battery

Supports Kensington security sock

Preinstalled:

Windows® Vista® Basic 32 with Office Ready

Windows Vista Basic 32 with Office Personal (in Japan only) √

Windows Vista Basic 32 with Office Personal/PowerPoint (in Japan only)

Windows Vista Basic 32 with Office Professional (in Japan only) √

Windows Vista Basic 32 √

Windows Vista Business 32 √

4 Chapter 1 Product description

Category

Serviceability

Description

Windows Vista Business 32 with Office Ready √

Windows Vista Business 32 with Office Personal (in Japan only) √

Windows Vista Business 32 with Office Personal/PowerPoint (in

Japan only)

Windows Vista Business with Office Professional (in Japan only) √

Windows Vista Business with Windows® XP Pro

Windows Vista Business with Windows XP Pro with Office

Personal/PowerPoint (in Japan only)

Windows Vista Business with Windows XP Pro with Office

Personal (in Japan only)

Windows Vista Business with Windows XP Pro with Office

Professional (in Japan only)

Windows Vista Business with Windows XP Pro with Office Ready √

Windows Vista Home Premium with Office Ready √

FreeDOS

Red Flag Linux (in the People's Republic of China only)

Restore media:

Windows Vista Basic 32 √

Windows Vista Home Premium

Windows Vista Business 32

Windows Vista Business 64

Windows XP Pro

Office Ready DVD

Red Flag Linux (in the People's Republic of China only)

DRDVD Windows Vista

DRDVD Windows XP Pro

Certified: Microsoft® WHQL

Web support:

Windows XP Pro

End-user replaceable parts:

AC adapter

Battery (system)

Hard drive

Computer models equipped with PM45 system board

5

Category Description

Optical drive √

Computer models equipped with PM45 system board

6 Chapter 1 Product description

2 External component identification

Top components

Display components

Components

(1)

(2)

Webcam light (select models only)

Webcam (select models only)

Description

On: The integrated camera is in use.

Records audio and video and captures still photographs.

Wireless antennae (select models only)

On select computer models, at least 2 antennae send and receive signals from one or more wireless devices. These antennae are not visible from the outside of the computer.

Top components 7

NOTE: For optimal transmission, keep the areas immediately around the antennae free from obstructions.

To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental

Notices that applies to your country or region. These notices are located in Help and Support.

TouchPad

Item

(1)

Component

TouchPad*

(2)

(3)

Left TouchPad button*

TouchPad scroll zone

8 Chapter 2 External component identification

Function

Moves the pointer and selects or activates items on the screen.

Functions like the left button on an external mouse.

Scrolls up or down.

Item Component Function

(4) Right TouchPad button* Functions like the right button on an external mouse.

*This table describes factory settings. View or change pointing device preferences as follows:

● In Windows Vista, select Start > Control Panel > Hardware and Sound > Mouse.

● In Windows XP, select Start > Control Panel > Printers and Other Hardware > Mouse.

Top components 9

Buttons, switch, lights, and speakers

Item

(1)

Component

Internal display switch

(2)

(3)

(4)

Caps lock light

Speakers (2)

Wireless light

(5) Wireless button

(6) Power button

Function

Turns off the display if the display is closed while the power is on.

On: Caps lock is on.

Produce sound.

● Blue: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP

Broadband Wireless Module, and/or a Bluetooth® device, is on.

● Amber: All wireless devices are off.

Turns the wireless feature on or off, but does not establish a wireless connection.

NOTE: You must set up or access a wireless network to establish a wireless connection.

● When the computer is off, press the button to turn on the computer.

● When the computer is on, press the button to turn off the computer.

● When the computer is in the Sleep state (Windows

Vista) or in Standby (Windows XP), press the button briefly to exit the Sleep state or Standby.

● When the computer is in Hibernation, press the button briefly to exit Hibernation.

If the computer has stopped responding and Windows® shutdown procedures are ineffective, press and hold the power button for at least 5 seconds to turn off the computer.

10 Chapter 2 External component identification

Keys

Item Component

(7) Power light

Function

To learn more about power settings, follow these steps:

● In Windows Vista, select Start > Control Panel >

System and Maintenance > Power Options.

● In Windows XP, select Start > Control Panel >

Performance and Maintenance > Power Options.

● On: The computer is on.

● Blinking: The computer is in the Sleep state (Windows

Vista) or Standby (Windows XP).

● Off: The computer is off or in Hibernation.

Item

(1)

Component esc key

(2)

(3)

(4)

(5)

(6)

(7) fn key

Windows logo key

Windows applications key

Integrated numeric keypad keys num lk key

Function keys

Function

Displays system information when pressed in combination with the fn key.

Executes frequently used system functions when pressed in combination with a function key or the esc key.

Displays the Windows Start menu.

Displays a shortcut menu for items beneath the pointer.

Can be used like the keys on an external numeric keypad.

Alternates between the navigation and numeric functions on the integrated numeric keypad.

Execute frequently used system functions when pressed in combination with the fn key.

Top components 11

Front components

Item

(1)

Component

Media Card Reader

(2) Drive light

(3) Audio-out (headphone) jack

(4)

(5)

Internal microphone

Audio-in (microphone) jack

Right-side components

Function

Supports the Memory Stick, Memory Stick Pro, Memory

Stick Duo, Secure Digital (SD) Memory Card,

MultimediaCard (MMC), and xD-Picture Card formats.

● Blinking turquoise: The hard drive or optical drive is being accessed.

● Amber: HP 3D DriveGuard has temporarily parked the hard drive.

Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio.

Records sound.

Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.

Item

(1)

(2)

(3)

Component

USB ports (2)

Optical drive

Security cable slot

Function

Connect optional USB devices.

Reads an optical disc.

Attaches an optional security cable to the computer.

NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.

12 Chapter 2 External component identification

Left-side components

Item

(1)

(2)

Component

RJ-11 (modem) jack

Vent

(3)

(4)

External monitor port

Battery light

(5)

(6)

(7)

(8)

Power connector

RJ-45 (network) jack

USB ports (2)

ExpressCard slot

Function

Connects a modem cable.

Enables airflow to cool internal components.

NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.

Connects an external VGA monitor or projector.

● Amber: A battery is charging.

● Turquoise: A battery is close to full charge capacity.

● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly.

● Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.

Connects an AC adapter.

Connects a network cable.

Connect optional USB devices.

Supports optional ExpressCards.

Left-side components 13

Bottom components

Item

(1)

(2)

(3)

Component

Battery bay

Battery release latches (2)

Vents (2)

(4)

(5)

(6)

Memory module compartment

Hard drive bay

WLAN module compartment (select models only)

Function

Holds the battery.

Release the battery from the battery bay.

Enable airflow to cool internal components.

NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.

Contains a memory module.

Holds the hard drive.

Contains a WLAN module slot.

CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support.

14 Chapter 2 External component identification

3 Illustrated parts catalog

Serial number location

The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems. The service tag provides the following information:

(1) Product name: This is the product name affixed to the front of the computer.

(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.

(3) Part number/Product number (p/n): This number provides specific information about the product's hardware components. The part number helps a service technician to determine what components and parts are needed.

(4) Model description: This is the number you use to locate documents, drivers, and support for your computer.

(5) Warranty period: This number describes the duration of the warranty period for this computer.

Serial number location 15

Computer major components

Item

(1)

Description

Display assemblies (include 2 WLAN antenna transceivers and cables)

17.0-inch, WXGA BrightView display assembly

17.0–inch WXGA BrightView display assembly with webcam

17.0-inch, WXGA Anti-Glare display assembly

16 Chapter 3 Illustrated parts catalog

Spare part number

490332-001

495897–001

490334-001

Item

(3)

(4)

(5)

(2)

Description

17.0-inch, WXGA WVA display assembly

17.0-inch, WXGA WVA display assembly with webcam

17.0–inch WXGA Anti-Glare display assembly with webcam

Display internal components: not illustrated

Display bezel without webcam

Display bezel with webcam

Display enclosure (includes 2 WLAN antenna transceivers and cables)

Display hinges (includes left and right hinges)

Display inverter

Switch cover (includes LED board and cable)

LED power button board (included with the switch cover, spare part number 490315-001)

Speakers

Keyboards

For use in Saudi Arabia

For use in Brazil

For use in the Czech Republic

For use in Denmark

For use in Europe

For use in Belgium

For use in French Canada

For use in France

For use in Greece

For use in Germany

For use in Israel

For use in Hungary

For use in Iceland

For use in Italy

For use in Japan

For use in South Korea

For use in Latin America

For use in Portugal

For use in Russia

For use in Sweden and Finland

For use in Slovakia

Spare part number

490333-001

495898-001

495899–001

490328-001

495738-001

490331-001

490329-001

490326-001

490315-001

490341-001

490327-171

490327-201

490327-221

490327-081

490327-021

490327-A41

490327-121

490327-051

490327-151

490327-041

490327-BB1

490327-211

490327-DD1

490327-061

490327-291

490327-AD1

490327-161

490327-131

490327-251

490327-B71

490327-231

Computer major components 17

(15)

(16)

(17)

(18)

(19)

Item

(9c)

(9d)

(10)

(11)

(8)

(9)

(9a)

(9b)

(6)

(7)

(12)

(13)

(14)

Description Spare part number

For use in Slovenia

For use in Spain

For use in Switzerland

For use in Thailand

For use in Turkey

For use in Taiwan

For use in the United Kingdom

For use in the United States

Top cover (includes TouchPad board and cable, and TouchPad button board and cable)

RJ–11 connector (included in cable kit, spare part number 490314-001)

For use only in Japan and Asia Pacific countries and regions

USB connector and cable

Modem

System boards (includes replacement thermal material and the ExpressCard assembly)

Iincludes 128-MB of graphics subsystem memory

Iincludes 256-MB of graphics subsystem memory

Optical drive connector board

Battery extender board

Processors (includes replacement thermal material) (not illustrated)

Intel Core2 Duo processors:

490327-BA1

490327-071

490327-111

490327-281

490327-141

490327-AB1

490327-031

490327-001

490342-001

490335-001

TouchPad (Included with top cover, spare part number 490342-001)

Plastics Kit (see

Plastics Kit on page 22

for more Plastics Kit spare part information):

ExpressCard slot bezel

WLAN module compartment cover

Hard drive bay cover

Memory module compartment cover

TouchPad cable (included with top cover, spare part number 490342-001)

TouchPad bracket (included with top cover, spare part number 490342-001)

Heat sink (includes replacement thermal material)

Fan

490325-001

490324-001

Broadcom Bluetooth modules (do not include Bluetooth module cable)

NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 490314-001. See

Cable Kit on page 23 for more Cable Kit spare part

number information.

For use in all countries and regions except Japan and Asia Pacific countries and regions 398393-002

450066-001

490313-001

461749-001

490311-001

490312-001

490310-001

490308-001

18 Chapter 3 Illustrated parts catalog

(24)

(22)

(23)

Item

(20)

(21)

(25)

Description

● P8400 2.26GHz (3-MB L2 cache, 1066-MHz FSB)

● P8600 2.40-GHz (3-MB L2 cache, 1066-MHz FSB)

● T9400 2.53-GHz (6-MB L2 cache, 1066-MHz FSB)

● T5670 1.80-GHz (2-MB L2 cache, 800-MHz FSB) (not available for Japan)*

● T5870 2.0-GHz (2-MB L2 cache, 800-MHz FSB)*

*Only available with Intel WLAN or no WLAN

Intel Celeron M processors:

● 575 2.0-GHz (1-MB L2 cache, 667-MHz FSB)

● 585 2.16-GHz (1-MB L2 cache, 667-MHz FSB)

RTC battery

Modem modules

Spare part number

491486–001

491487–001

491489–001

491488-001

490338-001

490336-001

490337-001

449137-001

NOTE: The modem module spare part kit does not include a modem module cable. The modem module cable is included in the Cable Kit, spare part number 490314-001. See

Cable Kit on page 23 for more Cable Kit spare part

number information.

For use only in all countries and regions except Australia and New Zealand 461749-001

For use only in Australia and New Zealand

8-cell, 63-Wh Li-ion battery

Base enclosure (includes rubber feet)

Rubber Kit (not illustrated, contains 7 computer feet and 8 display bezel screw covers)

461749-011

490306–001

490305-001

490339-001

Optical drives (include bezel and bracket)

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer

DVD-ROM Drive

DVD±RW SuperMulti Double-Layer Drive with LightScribe

DVD/CD-RW Combo Drive

Cable Kit (not illustrated; see Cable Kit on page 23

for more Cable Kit spare part number information)

WLAN modules

Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions except Pakistan, Russia, and the Ukraine

Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use only in Pakistan, Russia, and the Ukraine

490316–001

490317-001

490318-001

490319-001

490314-001

480985-001

482957-001

Broadcom BCM4312 802.11/b/g WLAN modules:

● For use in Antigua and Barbuda, Argentina, Aruba, Barbados, Belize, Canada, the

Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States

459263-001

● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,

Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,

Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,

Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,

459263-002

Computer major components 19

(26)

Item Description Spare part number

Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,

Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,

Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican

Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,

Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,

Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa,

Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the

Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,

Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,

Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,

Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,

Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands,

New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,

Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of

Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi

Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts &

Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,

Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia,

Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United

Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe

Broadcom 4322 802.11a/b/g/n WLAN modules:

● For use in Antigua & Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,

Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States

487330-001

● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,

Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,

Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,

Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,

Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,

Chile, the People's Republic of China, Columbia, Comoros, the Congo, Costa Rica,

Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican

Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,

Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,

Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau,

Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the

Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,

Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,

Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,

Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,

Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands,

New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,

Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of

Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi

Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and

Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,

Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia,

Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United

Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe

487330-002

Hard drives (include hard drive bracket)

320–GB, 5400–rpm

250–GB, 5400–rpm

160-GB, 5400-rpm

498310–001

490323–001

490322-001

490320-001

20 Chapter 3 Illustrated parts catalog

Item Description

(27)

120-GB, 7200-rpm

Memory modules (PC2-5300, 667-MHz, DDR2)

1-GB

2-GB

Memory modules (PC2-6400, 667–MHz, DDR2)

1-GB

2-GB

Spare part number

490321-001

495175-001

495176-001

491483–001

491484–001

Computer major components 21

Plastics Kit

Item Description

(1)

(2)

(3)

(4)

Plastics Kit:

ExpressCard slot bezel

WLAN module compartment cover (includes one captive screw, secured by a C-clip)

Memory module compartment cover (includes one captive screw, secured by a C-clip)

Hard drive bay cover (includes 2 captive screws, secured by C-clips)

Spare part number

490335-001

22 Chapter 3 Illustrated parts catalog

Cable Kit

Item Description

(1)

(2)

(3)

Cable Kit:

RJ-11 jack cable

Display lid switch module and cable

Bluetooth module cable

Spare part number

490314-001

Cable Kit 23

Mass storage devices

Item Description

(1)

(2)

Optical drives (include bezel and bracket)

DVD±RW SuperMulti Double-Layer Drive with LightScribe

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer

DVD/CD-RW Combo Drive

DVD–ROM Drive

Hard drives (include bracket)

320-GB, 5400-rpm

250-GB, 5400-rpm

160-GB, 5400-rpm

120-GB, 5400-rpm

Spare part number

490318-001

490316-001

490319-001

490317–001

498310-001

490323-001

490322-001

490320-001

490321-001

24 Chapter 3 Illustrated parts catalog

Miscellaneous parts

Description

AC adapter

90-W HP Smart AC adapter for use in all countries and regions except India

Carrying cases

HP Universal Nylon Case

HP Executive Leather Case

HP Deluxe Nylon Backpack

HP Deluxe Roller Case

USB 1.1 diskette drive

Power cords:

For use in Argentina

For use in Australia

For use in Brazil

For use in Denmark

For use in Europe

For use in Iceland

For use in India

For use in Italy

For use in Japan

For use in the People's Republic of China

For use in South Africa

For use in South Korea

For use in Switzerland

For use in Taiwan

For use in the United Kingdom

For use in the United States

Screw Kit

● Phillips PM2.0×2.0 broad-head screw

● Phillips PM2.0x3.0 screw

● Phillips PM2.0×4.0 screw

● Phillips PM2.5×4.0 screw

● Phillips PM2.5x6.0 captive screw

● Phillips PM2.5x9.0 screw

Spare part number

463955-001

439425-001

439427-001

439426–001

446929-001

359118-001

490371-D01

490371-011

490371-201

490371-081

490371-021

490371-BB1

490371-D61

490371-061

490371-291

490371-AA1

490371-AR1

490371-AD1

490371-111

490371-AB1

490371-031

490371-001

490340-001

Miscellaneous parts 25

Description

● Phillips PM3.0×4.0 screw

● Phillips PM2.5×10.0 captive screw

● Torx T8M2.0x2.0 broad-head screw

● Torx T8M2.5×7.0 slotted screw

● Torx T8M2.5×6.0 screw

● Torx T8M2.5×4.0 screw

● Torx T8M2.5×5.0 broad-head screw

● Torx T8M2.5×10.0 slotted screw

Spare part number

26 Chapter 3 Illustrated parts catalog

Sequential part number listing

Spare part number

398393-002

Description

439425-001

439426-001

439427-001

446929–001

449137-001

450066-001

459263-001

459263-002

461749-001

461749-011

463955-001

Bluetooth module for use in North America

NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth

module cable is included in the Cable Kit, spare part number 490314-001. See Cable Kit on page 23

for more

Cable Kit spare part number information.

HP Universal Nylon Case

HP Deluxe Nylon Backpack

HP Executive Leather Case

HP Deluxe Roller Case

RTC battery

Bluetooth module for use in Japan and Asia Pacific countries and regions

NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth

module cable is included in the Cable Kit, spare part number 490314-001. See Cable Kit on page 23

for more

Cable Kit spare part number information.

Broadcom BCM4312 802.11b/g WLAN module for use in Antigua and Barbuda, Argentina, Aruba, Barbados,

Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States

Broadcom BCM4312 802.11/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola,

Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,

Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,

Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo,

Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East

Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French

Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,

Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the

Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,

Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali,

Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,

Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New

Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,

Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San

Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,

Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts &

Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,

Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,

Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,

Yemen, Zaire, Zambia, and Zimbabwe

Modem module for use in all countries and regions except Australia and New Zealand

NOTE: The modem module spare part kit does not include a modem module cable. The modem module

cable is included in the Cable Kit, spare part number 490314-001. See Cable Kit on page 23 for more Cable

Kit spare part number information.

Modem module for use only in Australia and New Zealand

NOTE: The modem module spare part kit does not include a modem module cable. The modem module

cable is included in the Cable Kit, spare part number 490314-001. See Cable Kit on page 23 for more Cable

Kit spare part number information.

90-W HP Smart AC adapter for use in all countries and regions except India

Sequential part number listing 27

Spare part number

480985-001

Description

482957-001

487330-001

487330-002

490305-001

490306-001

490308-001

490310-001

490311-001

490312-001

490313-001

490314-001

490315-001

490316-001

490317-001

490318-001

490319-001

490320-001

490321-001

490322-001

490323-001

Intel Wi–Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions except Pakistan, Russia, and the Ukraine

Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use only in Pakistan, Russia, and the Ukraine

Broadcom 4322 802.11a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize, Canada, the

Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States

Broadcom 4322 802.11a/b//n WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,

Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,

Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central

African Republic, Chad, Chile, the People's Republic of China, Columbia, Comoros, the Congo, Costa Rica,

Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,

Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,

Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,

Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory

Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,

Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,

Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,

Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the

Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao

Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia,

Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St.

Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,

Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the

United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,

Zaire, Zambia, and Zimbabwe

Base enclosure (includes rubber feet)

8-cell, 63-Wh Li-ion battery

System board battery connector

System board optical disc drive connector

System board with 128-MB of graphics subsystem memory (Includes replacement thermal material, and the

ExpressCard assembly)

System board with 256-MB of graphics subsystem memory (Includes replacement thermal material, and the

ExpressCard assembly)

USB connectors, system board

Cable Kit (see

Cable Kit on page 23

for more Cable Kit spare part information)

Switch cover (includes LED board and cable)

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer (includes bezel and bracket)

DVD-ROM Drive

DVD±RW SuperMulti Double-Layer Drive with LightScribe (includes bezel and bracket)

DVD/CD-RW Combo Drive (includes bezel and bracket)

120-GB, 5400-rpm hard drive (includes bracket)

120-GB, 7200-rpm hard drive (includes bracket)

160-GB, 5400-rpm hard drive (includes bracket)

250-GB, 5400-rpm hard drive (includes bracket)

28 Chapter 3 Illustrated parts catalog

Spare part number

490327-201

490327-211

490327-221

490327-231

490327-251

490327-281

490327-291

490327-A41

490327-AB1

490327-AD1

490327-B71

490327-BA1

490327-BB1

490327-DD1

490328-001

490329-001

490324-001

490325-001

490326-001

490327-001

490327-021

490327-031

490327-041

490327-051

490327-061

490327-071

490327-081

490327-111

490327-121

490327-131

490327-141

490327-151

490327-161

490327-171

Description

Fan

Heat sink (includes replacement thermal material)

Display inverter

Keyboard for use in the United States

Keyboard for use anywhere in Europe

Keyboard for use in the United Kingdom

Keyboard for use in Germany

Keyboard for use in France.

Keyboard for use in Italy

Keyboard for use in Spain

Keyboard for use in Denmark

Keyboard for use in Switzerland

Keyboard for use in French Canada

Keyboard for use in Portugal

Keyboard for use in Turkey

Keyboard for use in Greece

Keyboard for use in Latin America

Keyboard for use in Saudi Arabia

Keyboard for use in Brazil

Keyboard for use in Hungary

Keyboard for use in the Czech Republic

Keyboard for use in Slovakia

Keyboard for use in Russia

Keyboard for use in Thailand

Keyboard for use in Japan

Keyboard for use in Belgium

Keyboard for use in Taiwan

Keyboard for use in South Korea

Keyboard for use in Sweden and Finland

Keyboard for use in Slovenia

Keyboard for use in Israel

Keyboard for use in Iceland

Display bezel

Bracket kit with display hinges (includes left and right hinges)

Sequential part number listing 29

Spare part number

Description

490330-001

490331-001

490334-001

490335-001

490336-001

LCD cable

Display enclosure (includes 2 wireless antenna transceivers and cables

490332-001 17.0-inch, WXGA display assembly with BrightView (includes 2 WLAN antenna transceivers and cables)

4490333-001 17.0-inch, WXGA display assembly with WVA (includes 2 WLAN antenna transceivers and cables)

17.0-inch, WXGA display assembly with Anti-Glare (includes 2 WLAN antenna transceivers and cables)

Plastics Kit (see

Plastics Kit on page 22 for more Plastics Kit spare part information)

490337-001

Intel Celeron M 575 2.0-GHz processor (1-MB L2 cache, 667-MHz FSB, includes replacement thermal material)

Intel Celeron M 585 2.16-GHz processor (1-MB L2 cache, 667-MHz FSB, includes replacement thermal material)

490338-001

490339-001

490340-001

490341-001

490342-001

490371-D01

Intel Core2 Duo T5870 2.00-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal material)

Rubber Kit (contains 6 computer feet and 8 display bezel screw covers)

Screw Kit

Speakers

Top cover (includes TouchPad board and cable, and TouchPad button board and cable)

Power cord for use in Argentina

490371-011

490371-201

490371-081

490371-021

490371-BB1

490371-D61

490371-061

490371-291

Power cord for use in Australia and New Zealand

Power cord for use in Brazil

Power cord for use in Denmark

Power cord for use in European countries

Power cord for use in Iceland

Power cord for use in India

Power cord for use in Italy

Power cord for use in Japan

490371–AA1 Power cord for use in the People's Republic of China

490371-AR1 Power cord for use in South Africa

490371-AD1

490371-111

Power cord for use in South Korea

Power cord for use in Switzerland

490371-AB1

490371-031

490371-001

491486-001

491487-001

Power cord for use in Taiwan

Power cord for use in the United Kingdom

Power cord for use in the United States

Intel Core2 Duo P8400 2.26-GHz processor (3-MB L2 cache, 1066-MHz FSB, includes replacement thermal material)

Intel Core2 Duo P8600 2.40-GHz processor (32-MB L2 cache, 1066-MHz FSB, includes replacement thermal material)

30 Chapter 3 Illustrated parts catalog

Spare part number

491489-001

Description

491488-001

495175-001

495176-001

495897-001

495898-001

495899-001

498310-001

Intel Core2 Duo T9400 2.53-GHz processor (6-MB L2 cache, 1066-MHz FSB, includes replacement thermal material)

Intel Core2 Duo T5670 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal material)

1-GB memory module (PC2-5300, 667-MHz, DDR2)

2-GB memory module (PC2-5300, 667-MHz, DDR2)

17.0-inch, WXGA display assembly with BrightView and webcam (includes 2 WLAN antenna transceivers and cables)

17.0-inch, WXGA display assembly with WVA and webcam (includes 2 WLAN antenna transceivers and cables)

17.0-inch, WXGA display assembly with AG and webcam (includes 2 WLAN antenna transceivers and cables)

320-GB, 5400-rpm hard drive (includes bracket)

TouchPad board (included with top cover, spare part number 490342-001) (includes cable)

TouchPad button board (included with top cover, spare part number 490342-001) (includes cable)

Sequential part number listing 31

4 Removal and replacement procedures

Preliminary replacement requirements

Tools required

You will need the following tools to complete the removal and replacement procedures:

● Flat-bladed screwdriver

● Magnetic screwdriver

● Phillips P0 and P1 screwdrivers

● Torx T8 screwdriver

Service considerations

The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

NOTE: As you remove each subassembly from the computer, place the subassembly (and all accompanying screws) away from the work area to prevent damage.

Plastic parts

Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.

32 Chapter 4 Removal and replacement procedures

Cables and connectors

CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer.

Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.

Drive handling

CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a drive, or loss of information, observe these precautions:

Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid touching the connector.

Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure that the optical drive tray is closed.

Handle drives on surfaces covered with at least one inch of shock-proof foam.

Avoid dropping drives from any height onto any surface.

After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.

Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.

Avoid exposing a drive to temperature extremes or liquids.

If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging and label the package “FRAGILE.”

Preliminary replacement requirements 33

Grounding guidelines

Electrostatic discharge damage

Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.

A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.

An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life expectancy.

CAUTION: To prevent damage to the computer when you are removing or installing internal components, observe these precautions:

Keep components in their electrostatic-safe containers until you are ready to install them.

Use nonmagnetic tools.

Before touching an electronic component, discharge static electricity by using the guidelines described in this section.

Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.

If you remove a component, place it in an electrostatic-safe container.

The following table shows how humidity affects the electrostatic voltage levels generated by different activities.

CAUTION: A product can be degraded by as little as 700 V.

Event

Walking across carpet

Walking across vinyl floor

Motions of bench worker

Removing DIPS from plastic tube

Removing DIPS from vinyl tray

Removing DIPS from Styrofoam

Removing bubble pack from PCB

Packing PCBs in foam-lined box

Typical electrostatic voltage levels

Relative humidity

10%

35,000 V

12,000 V

6,000 V

2,000 V

11,500 V

14,500 V

26,500 V

21,000 V

40%

15,000 V

5,000 V

800 V

700 V

4,000 V

5,000 V

20,000 V

11,000 V

55%

7,500 V

3,000 V

400 V

400 V

2,000 V

3,500 V

7,000 V

5,000 V

34 Chapter 4 Removal and replacement procedures

Packaging and transporting guidelines

Follow these grounding guidelines when packaging and transporting equipment:

● To avoid hand contact, transport products in static-safe tubes, bags, or boxes.

● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.

● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

● Place items on a grounded surface before removing items from their containers.

● Always be properly grounded when touching a component or assembly.

● Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.

● Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.

Workstation guidelines

Follow these grounding workstation guidelines:

● Cover the workstation with approved static-shielding material.

● Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment.

● Use conductive field service tools, such as cutters, screwdrivers, and vacuums.

● When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials.

● Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and

Styrofoam.

● Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items only at static-free workstations.

● Avoid contact with pins, leads, or circuitry.

● Turn off power and input signals before inserting or removing connectors or test equipment.

Preliminary replacement requirements 35

Equipment guidelines

Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.

● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.

● When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground. To be effective, the conductive strips must be worn in contact with the skin.

The following grounding equipment is recommended to prevent electrostatic damage:

● Antistatic tape

● Antistatic smocks, aprons, and sleeve protectors

● Conductive bins and other assembly or soldering aids

● Nonconductive foam

● Conductive tabletop workstations with ground cords of one megohm resistance

● Static-dissipative tables or floor mats with hard ties to the ground

● Field service kits

● Static awareness labels

● Material-handling packages

● Nonconductive plastic bags, tubes, or boxes

● Metal tote boxes

● Electrostatic voltage levels and protective materials

The following table lists the shielding protection provided by antistatic bags and floor mats.

Material

Antistatic plastic

Carbon-loaded plastic

Metallized laminate

Use

Bags

Floor mats

Floor mats

Voltage protection level

1,500 V

7,500 V

5,000 V

36 Chapter 4 Removal and replacement procedures

Unknown user password

If the computer you are servicing has an unknown user password, follow these steps to clear the password:

NOTE: These steps also clear CMOS.

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see Battery on page 40 ).

5.

Remove the real-time clock (RTC) battery (see

RTC battery on page 66

).

6.

Wait approximately 5 minutes.

7.

Replace the RTC battery and reassemble the computer.

8.

Connect AC power to the computer. Do not reinsert any batteries at this time.

9.

Turn on the computer.

All passwords and all CMOS settings have been cleared.

Preliminary replacement requirements 37

Component replacement procedures

This chapter provides removal and replacement procedures.

There are as many as 99 screws, in 14 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.

Serial number

The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems. The service tag provides the following information:

(1) Product name: This is the product name affixed to the front of the computer.

(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.

(3) Part number/Product number (p/n): This number provides specific information about the product's hardware components. The part number helps a service technician to determine what components and parts are needed.

(4) Model description: This is the number you use to locate documents, drivers, and support for your computer.

(5) Warranty period: This number describes the duration of the warranty period for this computer.

38 Chapter 4 Removal and replacement procedures

Computer feet

The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 490339-001. There are 7 rubber feet that attach to the base enclosure in the locations illustrated below.

Component replacement procedures 39

Battery

Description

8-cell, 63-Wh Li-ion battery

Spare part number

490306-001

Before disassembling the computer, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

Remove the battery:

1.

Turn the computer upside down on a flat surface, with the battery bay toward you.

2.

Slide the battery release latches (1) to release the battery.

3.

Remove the battery (2) from the computer.

Install the battery by inserting it into the battery bay until you hear a click.

40 Chapter 4 Removal and replacement procedures

Hard drive

NOTE: All hard drive spare part kits include a hard drive bracket.

Description

320-GB, 5400-rpm hard drive

250-GB, 5400–rpm hard drive

160-GB, 5400-rpm hard drive

120-GB, 5400-rpm hard drive

120-GB, 7200-rpm hard drive

Spare part number

498310–001

490323–001

490322-001

490320-001

490321-001

Before removing the hard drive, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see Battery on page 40 ).

Remove the hard drive:

1.

Position the computer with the front toward you.

2.

Loosen the two Phillips 6.0-mm captive screws (1) that secure the hard drive bay cover to the computer.

3.

Lift the right side of the hard drive bay cover (2), swing it to the left, and remove the cover (3). The hard drive bay cover is included in the Plastics Kit, spare part number 490335-001.

Component replacement procedures 41

4.

Loosen the Phillips 10.0-mm captive screw (1) that secures the hard drive to the computer.

5.

Grasp the Mylar tab (2) on the hard drive and slide the hard drive to the left to disconnect it from the system board.

6.

Remove the hard drive (3) from the hard drive bay.

7.

If it is necessary to replace the hard drive bracket, remove the four Phillips 4.0-mm hard drive bracket screws (1) from each side of the hard drive.

8.

Lift the bracket (2) straight up to remove it from the hard drive.

Reverse this procedure to reassemble and install the hard drive.

42 Chapter 4 Removal and replacement procedures

WLAN module

Description Spare part number

Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions except

Pakistan, Russia, and the Ukraine

480985-001

Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use only in Pakistan, Russia, and the Ukraine 482957-001

Broadcom BCM4312 802.11b/g WLAN module

● For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,

Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States 459263-001

● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,

Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,

Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,

Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,

Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of

China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,

Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El

Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,

Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,

Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland,

India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati,

Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,

Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,

Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,

Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New

Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New

Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania,

Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,

South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the

Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo,

Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the

United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,

Vietnam, Yemen, Zaire, Zambia, and Zimbabwe

459263-002

Broadcom 4322 802.11a/b/g/n WLAN modules:

● For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,

Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States

487330-001

● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,

Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,

Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,

Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,

Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of

China, Columbia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,

Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El

Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,

Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,

Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland,

India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati,

Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,

Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,

Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,

Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New

Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New

Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania,

Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,

South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the

Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo,

487330-002

Component replacement procedures 43

Description

Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the

United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,

Vietnam, Yemen, Zaire, Zambia, and Zimbabwe

Spare part number

Before removing the WLAN module, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

Remove the WLAN module:

1.

Position the computer with the front toward you.

2.

Loosen the Phillips 6.0-mm captive screw (1) that secures the WLAN module compartment cover to the computer.

3.

Lift the right side of the WLAN module compartment cover, swing it to the left, and remove the cover (2). The WLAN module compartment cover is included in the Plastics Kit, spare part number

490335-001.

4.

Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.

NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The white WLAN antenna cable is connected to the WLAN module “Aux” terminal.

5.

Remove the two Phillips 4.0-mm screws (2) that secure the WLAN module to the computer. (The edge of the module opposite the slot rises away from the computer.)

44 Chapter 4 Removal and replacement procedures

6.

Remove the WLAN module (3) by sliding the module away from the slot at an angle.

NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion.

Reverse this procedure to install the WLAN module.

Memory module

Description

1-GB (PC2-5300, 667-MHz, DDR2)

2-GB (PC2-5300, 667-MHz, DDR2)

1-GB (PC2-6400, 667-MHz, DDR2)

2-GB (PC2-6400, 667-MHz, DDR2)

Spare part number

495175-001

495176-001

491483-001

491484-001

Before removing the memory module, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see Battery on page 40 ).

Remove the memory module:

1.

Loosen the Phillips 6.0-mm captive screw (1) that secures the memory module compartment cover to the computer.

Component replacement procedures 45

2.

Lift the front edge of the cover (2), swing it up and back, and remove the cover (3). The memory module compartment cover is included in the Plastics Kit, spare part number 490335-001.

3.

Spread the retaining tabs (1) on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the computer.)

4.

Remove the memory module (2) by pulling the module away from the slot at an angle.

NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot.

Reverse this procedure to install a memory module.

46 Chapter 4 Removal and replacement procedures

Optical drive

NOTE: All optical drive spare part kits include an optical drive bezel.

Description

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer

DVD±RW SuperMulti Double-Layer Drive with LightScribe

DVD/CD-RW Combo Drive

DVD-ROM Drive

Spare part number

490316-001

490318-001

490319-001

490317-001

Before removing the optical drive, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see Battery on page 40 ).

Remove the optical drive:

1.

Position the computer with the right side toward you.

2.

Remove the Torx 7.0-mm screw (1) that secures the optical drive to the computer.

3.

Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (2) and press the tab to the left to release the optical drive from the computer.

4.

Remove the optical drive (3) from the computer.

5.

If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward you.

6.

Remove the two Phillips 3.0-mm screws (1) that secure the optical drive bracket to the optical drive.

Component replacement procedures 47

7.

Remove the optical drive bracket (2).

Reverse this procedure to reassemble and install an optical drive.

48 Chapter 4 Removal and replacement procedures

Switch cover and keyboard

Description

Greece

Hungary

Iceland

Israel

Italy

Japan

Switch cover (includes button board and cable)

Keyboards for use in the following countries or regions:

Brazil

The Czech Republic

Denmark

Europe

490327-201

490327-221

490327-081

490327-021

Belgium

France

French Canada

Germany

490327-A41

490327-051

490327-121

490327-041

490327-151

490327-211

490327-DD1

490327-BB1

490327-061

490327-291

Latin America

Portugal

Russia

Saudi Arabia

Slovakia

Slovenia

South Korea

Spain

Sweden and Finland

Switzerland

Taiwan

Thailand

Turkey

The United Kingdom

The United States

Spare part number

490315-001

490327-161

490327-131

490327-251

490327-171

490327-231

490327-BA1

490327-AD1

490327-071

490327-B71

490327-111

490327-AB1

490327-281

490327-141

490327-031

490327-001

Before removing the switch cover and keyboard, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see Battery on page 40 ).

Component replacement procedures 49

Remove the switch cover and keyboard:

1.

Remove the following screws:

(1) Two Slotted Torx 10.0-mm screws

(2) Three Torx 2.0-mm broad-head screws

2.

Remove the two Torx 7.0-mm screws that secure the keyboard to the computer.

3.

Turn the computer display-side up, with the front toward you.

4.

Open the computer as far as possible.

50 Chapter 4 Removal and replacement procedures

5.

Lift the switch cover (1) straight up until it disengages from the computer, and slide it back (2) until it rests on the display assembly.

6.

Lift up the rear edge of the keyboard (1), and slide it back (2) to disengage the four tabs on the front of the keyboard from the switch cover.

Component replacement procedures 51

7.

Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and disconnect the keyboard cable (2) from the system board.

8.

Remove the keyboard.

9.

Release the ZIF connector and disconnect the LED ribbon cable from the system board (1), and then lift the switch cover up to remove it (2) from the system board.

10.

Turn the switch cover over.

11.

Remove the two Phillips 2.0-mm broadhead screws (1) from the switch cover.

52 Chapter 4 Removal and replacement procedures

12.

Remove the LED power button board (2) from the switch cover.

Reverse this procedure to install the switch cover and keyboard.

Component replacement procedures 53

Speakers

Description

Speakers

Spare part number

490341-001

Before removing the speakers, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the keyboard (see

Switch cover and keyboard on page 49 ).

6.

Remove the switch cover (see

Switch cover and keyboard on page 49 ).

Remove the speakers:

1.

Disconnect the speaker cable (1) from the system board and remove the speaker cable from the clips and routing channel.

NOTE: The two speakers are connected with a single cable.

2.

Remove the four Phillips 4.0-mm screws (2) that secure the speakers to the top cover.

3.

Remove the speakers (3) from the top cover.

Reverse this procedure to install the speakers.

54 Chapter 4 Removal and replacement procedures

Display assembly

NOTE: All display assembly spare part kits include 2 WLAN antenna transceivers and cables.

Description

17-inch, WXGA BrightView display assembly

17-inch, WXGA BrightView display assembly with webcam

17-inch, WXGA WVA display assembly

17-inch, WXGA WVA display assembly with webcam

17-inch, WXGA +Anti-Glare display assembly

17-inch, WXGA + Anti-Glare display assembly with webcam

Spare part number

490332-001

495897-001

490333-001

495898-001

490334-001

495899-001

Before removing the display assembly, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see Battery on page 40 ).

5.

Disconnect the wireless antenna cables from the WLAN module (see

WLAN module on page 43 ).

6.

Remove the following components: a.

Keyboard (see

Switch cover and keyboard on page 49 )

b.

Switch cover (see

Switch cover and keyboard on page 49 )

c.

Speakers (see

Speakers on page 54

)

Remove the display assembly:

1.

Open the computer as far as possible.

2.

Disconnect the display panel cable (1) from the system board.

CAUTION: There is a ground loop off the display panel cable that is secured to the left hinge. Be sure you do not pull or damage the cable.

3.

Disconnect the webcam and microphone module cables (2) from the system board and then remove the cables from the routing path (3).

Component replacement procedures 55

4.

Make sure that the wireless antenna cables are disconnected from the WLAN module on the bottom of the computer, then remove the wireless antenna cables (4) from the clips and routing channels built into the top cover.

CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components.

5.

Remove the two Slotted Torx 10-mm screws (1) and the two Torx 7.0-mm screws (2) that secure the display assembly to the computer.

6.

Release the display panel cable ground loop (3) from the system board.

7.

Lift the display assembly (4) straight up and remove it.

56 Chapter 4 Removal and replacement procedures

8.

If it is necessary to replace the display bezel, display inverter, or display hinges, remove the eight rubber screw covers (1) and the eight Torx 6.0-mm screws (2) that secure the display bezel to the display assembly. The rubber screw covers are available in the Rubber Kit, spare part number

490339-001.

9.

Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display bezel until the bezel disengages from the display enclosure.

10.

Remove the display bezel (3). The display bezel is available using spare part number

495738-001.

Component replacement procedures 57

11.

If it is necessary to replace the webcam module from the display enclosure, gently pull the webcam module from the double-sided tape on the display enclosure (1) and disconnect the webcam cable from the module (2).

NOTE: To replace the webcam module in the display enclosure, align the holes on the webcam module with the pins on the display enclosure and press onto the double-sided tape.

12.

If it is necessary to replace the display inverter, remove the inverter (1) from the display enclosure as far as the display panel cable and the backlight cable will allow.

13.

Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.

14.

Remove the display inverter. The display inverter is available using spare part number

490326-001.

15.

If it is necessary to replace the display hinges, remove the two Torx 6.0-mm screws (1) that secure the display panel to the display enclosure.

58 Chapter 4 Removal and replacement procedures

16.

Remove the display panel (2).

17.

Remove the eight Phillips 3.0-mm screws (1) that secure each display hinge to the display panel.

NOTE: When removing or replacing the Phillips screws, be sure to remove or replace them in the same sequence as the numbering found on the display hinges (1–2–3–4).

18.

Remove the display hinges (2). The left and right display hinges are available using spare part number 490329-001.

Reverse this procedure to reassemble and install the display assembly.

Component replacement procedures 59

Top cover

Description

Top cover

Spare part number

490342-001

Before removing the top cover, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

)

Remove the top cover:

1.

Turn the computer upside down, with the front toward you.

2.

Remove the 12 top cover slotted Torx 7.0-mm screws.

60 Chapter 4 Removal and replacement procedures

3.

Remove the three Phillips 2.0-mm broad-head screws from the optical drive bay (1), and remove the Torx 4.0-mm screw from the hard drive bay (2).

4.

Turn the computer right-side up.

5.

Remove the three slotted Torx 7.0-mm screws from the top cover.

6.

Lift the rear edge of the top cover (1) until it disengages from the base enclosure. Then tilt the top cover back (2) until the TouchPad cable is accessible.

Component replacement procedures 61

7.

Release the ZIF connector (1) to which the TouchPad cable is connected, and then disconnect the

TouchPad cable (2) from the system board.

8.

Remove the top cover.

Reverse this procedure to install the top cover.

62 Chapter 4 Removal and replacement procedures

USB board

1.

Disconnect the USB cable from the system board (1).

2.

Lift up the USB connector and remove the cable from the cable routing path (2).

3.

Remove the Phillips 9.0-mm screw (3) and the Phillips 4.0-mm screw (4) from the system board.

4.

Remove the USB board (5).

Reverse this procedure to install the USB board.

Component replacement procedures 63

Bluetooth module

NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 490314-001. See

Cable Kit on page 23

for more Cable Kit spare part number information.

Description

For use in all countries and regions except Japan and Asia Pacific countries and regions

For use only Japan and Asia Pacific countries and regions

Spare part number

398393-002

450066-001

Before removing the Bluetooth module, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

Remove the Bluetooth module:

1.

Disconnect the Bluetooth module cable (1) from the system board.

2.

Remove the Bluetooth module cable (2) from the routing path.

3.

Remove the Phillips 4.0-mm screw (3) that secures the Bluetooth module to the base enclosure.

64 Chapter 4 Removal and replacement procedures

4.

Remove the Bluetooth module (4) from the base enclosure.

Reverse this procedure to install the Bluetooth module.

Component replacement procedures 65

RTC battery

NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS settings to be cleared.

Description

RTC battery

Spare part number

449137-001

Before removing the RTC battery, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

h.

System board (see

System board on page 68

)

Remove the RTC battery:

1.

Turn the system board upside down, with the audio connectors toward you.

66 Chapter 4 Removal and replacement procedures

2.

Remove the RTC battery from the socket on the system board.

Reverse this procedure to install the RTC battery.

Component replacement procedures 67

System board

NOTE: All system board spare part kits include the ExpressCard assembly.

NOTE: All system board spare part kits include replacement thermal material.

Description

System board includes 128-MB of graphics subsystem memory

System board includes 256-MB of graphics subsystem memory

Spare part number

490311-001

490312-001

Before removing the system board, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board:

● Memory module (see

Memory module on page 45

)

WLAN module (see WLAN module on page 43 )

● Processor (see

Processor on page 76 )

To remove the system board:

1.

Remove the four Phillips 4.0-mm screws (1) that secure the optical drive connector board to the base enclosure.

2.

Remove the Torx 6.0-mm screw (2) that secures the system board to the base enclosure.

68 Chapter 4 Removal and replacement procedures

3.

Remove the three Torx 6.0-mm screws (3) that secure the battery connector board to the base enclosure.

4.

Flex the left side of the base enclosure until the external monitor connector (1) and the heat sink

(2) are clear of the openings in the base enclosure.

5.

Lift the rear edge of the system board (3) until it rests at an angle.

6.

Remove the system board (4) from the base enclosure by sliding it back.

Reverse the preceding procedure to install the system board.

Component replacement procedures 69

Fan

Description

Fan

Spare part number

490324-001

Before removing the fan, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

h.

System board (see

System board on page 68

)

Remove the fan:

1.

Remove the two Torx 6.0-mm screws (1) that secure the fan to the base enclosure.

70 Chapter 4 Removal and replacement procedures

2.

Remove the fan (2) from the base enclosure.

Reverse this procedure to install the fan.

NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of the computer.

The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist. These conditions are affected by high external temperatures, system power consumption, power management/battery conservation configurations, battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side of the computer.

Component replacement procedures 71

Modem module

NOTE: The modem module spare part kit does not include a modem module cable. The modem module cable is included in the Cable Kit, spare part number 490314-001. See

Cable Kit on page 23

for more Cable Kit spare part number information.

Description

For use in all countries and regions except Australia and New Zealand

For use only in Australia and New Zealand

Spare part number

461749-001

461749-011

Before removing the modem module, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

h.

System board (see

System board on page 68

)

Remove the modem module:

1.

Turn the system board upside down, with the audio connectors toward you.

2.

Remove the two Phillips 4.0-mm screws (1) that secure the modem module to the system board.

3.

Lift the modem module (2) straight up to release it from the system board.

72 Chapter 4 Removal and replacement procedures

4.

Disconnect the modem module cable (3) .

5.

Remove the modem module.

Reverse this procedure to install the modem module.

Component replacement procedures 73

Heat sink

NOTE: The heat sink spare part kit includes replacement thermal material.

Description

Heat sink (includes replacement thermal material)

Spare part number

490325-001

Before removing the heat sink, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

h.

System board (see

System board on page 68

)

Remove the heat sink:

1.

Turn the system board upside down, with the audio connectors toward you.

2.

Remove the two Phillips 10-mm captive screws from the heat sink extension (1).

3.

Following the 1, 2, 3, 4 sequence stamped into the heat sink, loosen the four Phillips 10-mm captive screws (2) around the processor.

74 Chapter 4 Removal and replacement procedures

4.

Remove the heat sink (3).

NOTE: The thermal material must be thoroughly cleaned from the surfaces of the system board (1), (2), and (3), and the heat sink components (4) and (5) each time the heat sink is removed.

Replacement thermal material is included with all heat sink, system board, and processor spare part kits.

Reverse this procedure to install the heat sink.

Component replacement procedures 75

Processor

NOTE: All processor spare part kits include replacement thermal material.

Description

Intel Core2 Duo processors

● P8400 2.26-GHz processor (3-MB L2 cache, 1066-MHz FSB)

● P8600 2.4-GHz processor (3-MB L2 cache, 1066-MHz FSB)

● T9400 2.53-GHz processor (6-MB L2 cache, 1066-MHz FSB)

● T5670 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB)

● T5870 2.0-GHz processor (2-MB L2 cache, 800-MHz FSB)

Intel Celeron M Processors

● Cel-575 2.0-GHz processor (1-MB, 667-MHz FSB)

● Cel-585 2.16-GHz processor (1-MB, 667-MHz FSB)

Spare part number

491486-001

491487-001

491489-001

491488-001

490388-001

490336-001

490337-001

Before removing the processor, follow these steps:

1.

Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.

Disconnect all external devices connected to the computer.

3.

Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

4.

Remove the battery (see

Battery on page 40 ).

5.

Remove the following components: a.

Hard drive (see Hard drive on page 41 )

b.

Optical drive (see

Optical drive on page 47

) c.

Keyboard (see

Switch cover and keyboard on page 49 )

d.

Switch cover (see

Switch cover and keyboard on page 49 )

e.

Speakers (see Speakers on page 54

) f.

Display assembly (see

Display assembly on page 55

) g.

Top cover (see Top cover on page 60 )

h.

System board (see

System board on page 68

)

Remove the processor:

1.

Turn the system board upside down, with the USB connectors toward you.

2.

Use a flat-bladed screwdriver to turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.

76 Chapter 4 Removal and replacement procedures

3.

Lift the processor (2) straight up and remove it.

NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned with the triangle (4) embossed on the processor socket.

Reverse this procedure to install the processor.

Component replacement procedures 77

5 Computer Setup

Starting Computer Setup

Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load.

NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer.

NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate and make selections.

NOTE: An external keyboard connected by USB can be used with Computer Setup only if USB legacy support is enabled.

To start Computer Setup:

1.

Turn on or restart the computer.

2.

Before Windows® opens and while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen, press f10 .

78 Chapter 5 Computer Setup

Using Computer Setup

Navigating and selecting in Computer Setup

The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and

System Configuration menus.

1.

Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the

"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.

Because Computer Setup is not Windows-based, it does not support the TouchPad. Navigation and selection are by keystroke:

● To choose a menu or a menu item, use the arrow keys.

● To select an item, press enter .

● To close open dialog boxes and return to the main Computer Setup screen, press esc .

● To view navigation information, press f1 .

● To change the language, press f2 .

2.

Select the File, Security, Diagnostics, or System Configuration menu.

3.

To exit Computer Setup, choose one of the following methods:

● To exit Computer Setup without saving your preferences, use the arrow keys to select File >

Ignore Changes and Exit. Then follow the instructions on the screen.

● To save your preferences and exit Computer Setup, use the arrow keys to select File > Save

Changes and Exit. Then follow the instructions on the screen.

Your preferences go into effect when the computer restarts.

Restoring factory settings in Computer Setup

To return all settings in Computer Setup to the values that were set at the factory, follow these steps:

1.

Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the

"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.

2.

Use the arrow keys to select File > Restore defaults, and then press enter .

3.

When the confirmation dialog box opens, press f10 .

4.

To save your preferences and exit Computer Setup, use the arrow keys to select File > Save

Changes and Exit. Then follow the instructions on the screen.

Your preferences go into effect when the computer restarts.

NOTE: Your password settings and security settings are not changed when you restore the factory settings.

Using Computer Setup 79

Computer Setup menus

The menu tables in this section provide an overview of Computer Setup options.

NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.

File menu

Select

System information

Restore defaults

Ignore changes and exit

Save changes and exit

To do this

● View identification information for the computer and the batteries in the system.

● View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version.

Replace the configuration settings in Computer Setup with the original factory settings. (Password settings and security settings are not changed when you restore the factory settings.)

Cancel any changes entered during the current session. Then exit and restart the computer.

Save any changes entered during the current session. Then exit and restart the computer. Your changes go into effect when the computer restarts.

80 Chapter 5 Computer Setup

Security menu

NOTE: Some of the menu items listed in this section may not be supported by your computer.

Select To do this

Setup BIOS Administrator Password Set up a BIOS administrator password.

User Management (requires a BIOS administrator password) ● Create a new BIOS user account.

Password Policy (requires a BIOS administrator password)

HP SpareKey

● View a list of ProtectTools users.

Revise password policy criteria.

Enable/disable HP SpareKey (enabled by default).

Always prompt for HP SpareKey Enrollment

Fingerprint Reset on Reboot (If Present)

Allow reset of HP ProtectTools security keys

Change Password

HP SpareKey Enrollment

DriveLock Passwords

Enable/disable HP SpareKey enrollment (enabled by default).

Enable/disable the fingerprint reader (select models only; disabled by default).

Enable/disable reset of HP ProtectTools security keys.

Enter, change, or delete a BIOS administrator password.

Enroll or reset HP SpareKey, which is a set of security questions and answers used if you forget your password.

● Enable/disable DriveLock on any computer hard drive

(enabled by default).

Automatic DriveLock

Disk Sanitizer

System IDs

● Change a DriveLock user password or master password.

NOTE: DriveLock settings are accessible only when you enter Computer Setup by turning on (not restarting) the computer.

Enable/disable Automatic DriveLock support.

Run Disk Sanitizer to destroy all existing data on the primary hard drive or the drive in the upgrade bay.

CAUTION: If you run Disk Sanitizer, the data on the selected drive is destroyed permanently.

Enter a user-defined computer asset tracking number and ownership tag.

Diagnostics menu

Select

Hard Drive Self-Test options

Memory Check

Startup Check (select models only)

To do this

Run a comprehensive self-test on any hard drive in the system.

Run a comprehensive check on system memory.

Verify the system components needed for starting the computer.

Computer Setup menus 81

System Configuration menu

NOTE: Some of the listed System Configuration options may not be supported by your computer.

Select

Language (or press f2 )

Boot options

Device configurations

To do this

Change the Computer Setup language.

● Set f9 , f10 , and f12 delay when starting up.

● Enable/disable CD-ROM boot.

● Enable/disable floppy boot.

● Enable/disable internal network adapter boot and set the boot mode (PXE or

RPL).

● Enable/disable MultiBoot, which sets a boot order that can include most boot devices in the system.

● Set the Express Boot Popup delay in seconds.

● Set the boot order.

● Swap the functions of the fn key and left ctrl key.

● Enable/disable multiple standard pointing devices at startup. (To set the computer to support only a single, usually nonstandard, pointing device at startup, select Disable.)

● Enable/disable USB legacy support. When enabled, USB legacy support allows the following:

◦ Use of a USB keyboard, mouse, and hub in Computer Setup even when a Windows operating system is not running.

◦ Startup from bootable USB devices, including a hard drive, diskette drive, or optical drive connected by a USB port to the computer or to an optional docking device (select models only).

● Select a parallel port mode: EPP (Enhanced Parallel Port), standard, bidirectional, or ECP (Enhanced Capabilities Port).

● Enable/disable BIOS DMA data transfers.

● Enable/disable fan always on while connected to an AC outlet.

● Enable/disable Intel® Data Execution Prevention or AMD PSAE Execution

Disable. When enabled, the processor can disable some virus code execution, which helps to improve computer security.

● Enable/disable LAN Power Save. When enabled, saves power by turning off the LAN when not in use.

● Enable/disable SATA Native Mode.

● Enable/disable Dual Core CPU.

● Enable/disable Secondary Battery Fast Charge.

● Choose Bit-shift or LBA assisted HDD Translation Mode.

● Enable/disable Windows direct application launcher.

● Enable/disable HP Lockout.

82 Chapter 5 Computer Setup

Select

Built-In Device Options

Port Options

To do this

● Enable/disable embedded WWAN Device Radio.

● Enable/disable embedded WLAN Device Radio.

● Enable/disable embedded Bluetooth® Device Radio.

● Enable/disable LAN/WLAN Switching. When enabled, switches to a WLAN when a LAN is either unavailable or disconnected.

● Enable/disable Wake on LAN from Off.

● Enable/disable the ambient light sensor.

● Enable/disable the serial port.

● Enable/disable the parallel port.

● Enable/disable the flash media reader.

● Enable/disable the USB port.

CAUTION: Disabling the USB port also disables MultiBay II devices and

ExpressCard devices on the advanced port replicator.

● Enable/disable the 1394 port.

● Enable/disable the cardbus slot.

● Enable/disable the ExpressCard slot.

● Enable/disable the infrared port.

● Enable/disable the optical disk drive.

● Enable/disable the network controller.

Computer Setup menus 83

6 Specifications

Computer specifications

Metric U.S.

Dimensions

Depth

Width

Height (front to rear)

28.50 cm

39.60 cm

3.23 to 3.58 cm

Weight (equipped with optical drive, hard drive, and battery) 2.95 kg

Input power

Operating voltage

Operating current

19.0 V dc @ 4.74 A – 90 W

4.74 A

Temperature

Operating (not writing to optical disc)

Operating (writing to optical disc)

Nonoperating

Relative humidity

Operating

Nonoperating

Maximum altitude (unpressurized)

0°C to 35°C

5°C to 35°C

-20°C to 60°C

10% to 90%

5% to 95%

Operating

Nonoperating

Shock

Operating

Nonoperating

Random vibration

Operating

-15 m to 3,048 m

-15 m to 12,192 m

125 g, 2 ms, half-sine

200 g, 2 ms, half-sine

11.22 in

15.60 in

1.27 to 1.41 in

6.50 lbs

32°F to 95°F

41°F to 95°F

-4°F to 140°F

-50 ft to 10,000 ft

-50 ft to 40,000 ft

0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate

84 Chapter 6 Specifications

Metric U.S.

Nonoperating 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate

NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures.

17.0-inch, WXGA+WVA display specifications

Metric

Dimensions

Height

Width

Diagonal

Number of colors

Contrast ratio

Brightness

Pixel resolution

Pitch

Format

Configuration

Backlight

Character display

Total power consumption

Viewing angle

24.4 cm

38.1 cm

43.2 cm

Up to 16.8 million

200:1 (typical)

180 nits (typical)

U.S.

9.6 in

15.0 in

17.0 in

0.259 × 0.259 mm

1440 × 900

RGB vertical stripe

CCFT

80 × 25

6.5 W

+/-45 horizontal, +15/–35° vertical (typical)

17.0-inch, WXGA+WVA display specifications 85

Hard drive specifications

320-GB 250-GB* 160-GB* 120-GB*

Dimensions

Height

Width

Weight

Interface type

Transfer rate

Security

Seek times (typical read, including setting)

Single track

Average

Maximum

Logical blocks

9.5 mm

70 mm

101 g

SATA

100 MB/sec

ATA security

3 ms

13 ms

24 ms

625,141,400

9.5 mm

70 mm

101 g

SATA

100 MB/sec

ATA security

3 ms

13 ms

24 ms

488,376,120

9.5 mm

70 mm

101 g

SATA

100 MB/sec

ATA security

3 ms

13 ms

24 ms

312,560,640

9.5 mm

70 mm

101 g

SATA

100 MB/sec

ATA security

3 ms

13 ms

24 ms

234,420,480

Disc rotational speed 5400 rpm 5400 rpm 5400 rpm 7200 and

5400 rpm

5°C to 55°C (41°F to 131°F) Operating temperature

*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.

NOTE: Certain restrictions and exclusions apply. Contact technical support for details.

86 Chapter 6 Specifications

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW

Double-Layer specifications

Applicable disc Read: Write:

CD-DA, CD+(E)G, CD-MIDI, CDTEXT,

CD-ROM, CD-ROM XA,

MIXED MODE CD, CD-I, CD-I Bridge

(Photo-CD, Video CD), Multisession CD

(Photo-CD, CD-EXTRA, Portfolio, CD-

R, CD-RW), CD-R, CD-RW,

DVDROM (DVD-5, DVD-9, DVD-10,

DVD-18), DVD-R, DVD-RW, DVD+R,

DVD+RW, DVD-RAM, HD-

ROM (Single Layer), HD-ROM (Dual

Layer), HD DVD-R, HD DVD-R for

Dual Layer, HD DVD-RW

CD-R and CD-RW DVD+R, DVD+R(9),

DVD+RW, DVD-R, DVD-R(9),DVD-RW,

DVD-RAM

CD DVD HD

170 ms

8 MB

170 ms 230 ms

Access time

Random

Cache buffer

Data transfer rate

24X CD-ROM

8X DVD

24X CD-R

16X CD-RW

8X DVD+R

4X DVD+RW

8X DVD-R

4X DVD-RW

2.4X DVD+R(9)

5X DVD-RAM

1X BD-ROM

1X BD-R read

1X BD-RE read

Transfer mode

3,600 KB/sec

10,800 KB/sec

3,600 KB/sec

2,400 KB/sec

10,800 KB/sec

5,400 KB/sec

10,800 KB/sec

5,400 KB/sec

2,700 KB/sec

6,750 KB/sec

4,500 KB/sec

4,500 KB/sec

4,500 KB/sec

Multiword DMA Mode

Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer specifications 87

DVD±RW SuperMulti Double-Layer Combo Drive specifications

Applicable disc Read:

CD

< 175 ms

2 MB

Write:

CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-

ROM, CD-ROM XA, MIXED MODE CD, CD-I,

CD-I Bridge (Photo-CD, Video CD), Multisession

CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CD-

RW), CD-R, CD-RW, DVD-ROM (DVD-5,

DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,

DVD+R, DVD+RW, DVD-RAM

CD-R and CD-RW

DVD+R, DVD+RW, DVD-R, DVD-

RW, DVD-RAM

DVD

< 230 ms

Access time

Random

Cache buffer

Data transfer rate

24X CD-ROM

8X DVD-ROM

24X CD-R

16X CD-RW

8X DVD+R

4X DVD+RW

8X DVD-R

4X DVD-RW

2.4X DVD+R(9)

5X DVD-RAM

Transfer mode

3,600 KB/sec

10,800 KB/sec

3,600 KB/sec

2,400 KB/sec

10,800 KB/sec

5,400 KB/sec

10,800 KB/sec

5,400 KB/sec

2,700 KB/sec

6,750 KB/sec

Multiword DMA Mode

88 Chapter 6 Specifications

DVD/CD-RW Combo Drive specifications

Applicable disc

Access time

Random

Cache buffer

Data transfer rate

24X CD-ROM

8X DVD

24X CD-R

24X CD-RW

Transfer mode

Read:

CD

< 110 ms

2 MB

Write:

CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-

ROM, CD-ROM XA, MIXED MODE CD, CD-I,

CD-I Bridge (Photo-CD, Video CD), Multisession

CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CD-

RW), CD-R, CD-RW, DVD-ROM (DVD-5,

DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,

DVD+R, DVD+RW, DVD-RAM

CD-R and CD-RW

DVD

< 130 ms

3,600 KB/sec

3,600 KB/sec

3,600 KB/sec

3,600 KB/sec

Multiword DMA mode 2

DVD/CD-RW Combo Drive specifications 89

DVD-ROM Drive specifications

Applicable disc

Access time

Random

Cache buffer

Data transfer rate

CD-R (24X)

CD-RW (10X)

CD-ROM (24X)

DVD (8X)

Multiword DMA mode 2

DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1 and 2), CD Digital Audio,

CD-XA ready (Mode 2, Form 1 and Form 2), CD-I (Mode 2, Form 1 and Form 2), CD-R, CD-

RW, Photo CD (single and multisession), CD-Bridge

CD DVD

< 100 ms

512 KB

< 125 ms

3600 KB/s (150 KB/s at 1X CD rate)

1500 KB/s (150 KB/s at 1X CD rate)

3600 KB/s (150 KB/s at 1X CD rate)

10,800 KB/s (1,352 KB/s at 1X DVD rate)

16.6 MB/s

90 Chapter 6 Specifications

System DMA specifications

Hardware DMA System function

DMA0

DMA1*

DMA2*

DMA3

DMA4

DMA5*

Not applicable

Not applicable

Not applicable

Not applicable

Direct memory access controller

Available for ExpressCard

DMA6

DMA7

Not assigned

Not assigned

*ExpressCard controller can use DMA 1, 2, or 5.

System DMA specifications 91

System interrupt specifications

Hardware IRQ System function

IRQ0

IRQ1

IRQ2

IRQ3

IRQ4

IRQ5*

IRQ6

IRQ7*

IRQ8

IRQ9*

IRQ10*

IRQ11

System timer

Standard 101-/102-Key or Microsoft® Natural Keyboard

Cascaded

Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD

COM1

Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax

Modem with SmartCP

Diskette drive

Parallel port

System CMOS/real-time clock

Microsoft ACPI-compliant system

Intel USB UHCI controller—24C2

Intel 82852/82855 GM/GME Graphic Controller

Realtek RTL8139 Family PCI Fast Ethernet Controller

Intel USB EHCI controller—24CD

Intel USB UHCI controller—24C4

Intel USB UHCI controller—24C7

Intel Pro/Wireless 2200BG

IRQ12

IRQ13

IRQ14

IRQ15

TI OHCI 1394 host controller

TI PCI1410 CardBus controller

Synaptics PS/2 TouchPad

Numeric data processor

Primary IDE channel

Secondary IDE channel

*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.

NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port may assert IRQ3 or IRQ4.

92 Chapter 6 Specifications

System I/O address specifications

I/O address (hex)

100 - 16F

170 - 177

178 - 1EF

1F0 - 1F7

1F8 - 200

201

202 - 21F

093 - 09F

0A0 - 0A1

I/O Address (hex)

0A2 - 0BF

0C0 - 0DF

0E0 - 0EF

0F0 - 0F1

0F2 - 0FF

062 - 063

064

065 - 06F

070 - 071

072 - 07F

080 - 08F

090 - 091

092

000 - 00F

010 - 01F

020 - 021

022 - 024

025 - 03F

02E - 02F

040 - 05F

044 - 05F

060

061

System function (shipping configuration)

DMA controller no. 1

Unused

Interrupt controller no. 1

Opti chipset configuration registers

Unused

87334 “Super I/O” configuration for CPU

Counter/timer registers

Unused

Keyboard controller

Port B

Unused

Keyboard controller

Unused

NMI enable/RTC

Unused

DMA page registers

Unused

Port A

Unused

Interrupt controller no. 2

System Function (shipping configuration)

Unused

DMA controller no. 2

Unused

Coprocessor busy clear/reset

Unused

Unused

Secondary fixed disk controller

Unused

Primary fixed disk controller

Unused

JoyStick (decoded in ESS1688)

Unused

System I/O address specifications 93

I/O address (hex)

300 - 31F

320 - 36F

370 - 377

378 - 37F

380 - 387

388 - 38B

38C - 3AF

3B0 - 3BB

220 - 22F

230 - 26D

26E - 26

278 - 27F

280 - 2AB

2A0 - 2A7

2A8 - 2E7

2E8 - 2EF

2F0 - 2F7

2F8 - 2FF

3BC - 3BF

3C0 - 3DF

3E0 - 3E1

3E2 - 3E3

3E8 - 3EF

3F0 - 3F7

3F8 - 3FF

CF8 - CFB

CFC - CFF

System function (shipping configuration)

Entertainment audio

Unused

Unused

Unused

Unused

Unused

Unused

Reserved serial port

Unused

Infrared port

Unused

Unused

Secondary diskette drive controller

Parallel port (LPT1/default)

Unused

FM synthesizer—OPL3

Unused

VGA

Reserved (parallel port/no EPP support)

VGA

ExpressCard controller in CPU

Unused

Internal modem

“A” diskette controller

Serial port (COM1/default)

PCI configuration index register (PCIDIVO-1)

PCI configuration data register (PCIDIVO-1)

94 Chapter 6 Specifications

System memory map specifications

Size

58 MB

58 MB

2 MB

4 GB

64 KB

640 KB

128 KB

48 KB

160 KB

64 KB

15 MB

Memory address

00000000-0009FFFF

000A0000-000BFFFF

000C0000-000CBFFF

000C8000-000E7FFF

000E8000-000FFFFF

00100000-00FFFFFF

04800000-07FFFFFF

04800000-07FFFFFF

08000000-080FFFFF

08200000-FFFEFFFF

FFFF0000-FFFFFFFF

System function

Base memory

Video memory

Video BIOS

Unused

System BIOS

Extended memory

Super extended memory

Unused

Video memory (direct access)

Unused

System BIOS

System memory map specifications 95

7 Screw listing

This section provides specification and reference information for the screws and screw locks used in the computer. All screws listed in this section are available in the Screw Kit, spare part number

490340-001.

96 Chapter 7 Screw listing

Phillips PM2.0×2.0 broad-head screw

Color

Black

Quantity

3

Length

2.0 mm

Thread

2.0 mm

Head diameter

5.0 mm

Where used: 3 screws that secure the top cover to the display enclosure

Phillips PM2.0×2.0 broad-head screw 97

Phillips PM2.0x2.0 broad-head screw

Color

Black

Quantity

2

Length

2.0 mm

Thread

2.0 mm

Head diameter

6.0 mm

Where used: 2 screws that secure the button board to the switch cover

98 Chapter 7 Screw listing

Phillips PM2.0×3.0 screw

Color

Silver

Quantity

10

Length

3.0 mm

Thread

2.0 mm

Head diameter

4.5 mm

Where used: 2 screws that secure the optical drive bracket to the optical drive

Where used: 8 screws that secure the display hinges to the display assembly

Phillips PM2.0×3.0 screw 99

Phillips PM2.0x4.0 screw

Color

Black

Quantity

5

Length

4.0 mm

Thread

2.0 mm

Head diameter

4.5 mm

Where used: 1 screw that secures the Blueotooth module to the base enclosure

Where used: 4 screws that secure the optical drive connector board to the system board

100 Chapter 7 Screw listing

Phillips PM2.5×4.0 screw

Color

Silver

Quantity

2

Length

4.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used: 2 screws that secure the WLAN module to the system board

Phillips PM2.5×4.0 screw 101

Phillips PM2.5×4.0 screw

Color

Black

Quantity

9

Length

4.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used: 4 screws that secure the speakers to the system board

Where used: 2 wireless antenna transceiver screws that secure the transceiver to the base enclosure

102 Chapter 7 Screw listing

Where used: 2 screws that secure the modem module to the system board

Where used: 1 screw that secures the USB board to the base enclosure

Phillips PM2.5×4.0 screw 103

Phillips PM2.5×6.0 captive screw

Color

Black

Quantity

4

Length

6.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used:

(1) Two captive screws that secure the hard drive bay cover to the computer (screws are secured by Cclips)

(2) One captive screw that secures the WLAN module compartment cover to the computer (screw is secured by a C-clip)

(3) One captive screw that secures the memory module compartment cover to the computer (screw is secured by a C-clip)

104 Chapter 7 Screw listing

Phillips PM2.5×9.0 screw

Color

Black

Quantity

1

Length

9.0 mm

Thread

2.5 mm

Head diameter

4.5 mm

Where used: 1 screw that secures the USB board to the base enclosure

Phillips PM2.5×9.0 screw 105

Phillips PM2.5×10.0 captive screw

Color

Black

Quantity

1

Length

10.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used: One captive screw that secures the hard drive to the computer (screw is secured to the hard drive bracket)

106 Chapter 7 Screw listing

Phillips PM2.5x10.0 captive screw

Color

Silver

Quantity

6

Length

10.0 mm

Thread

2.5 mm

Head diameter

5.9 mm

Where used: 6 captive screws that secure the heat sink to the system board (screws are secured to the heat sink by C-clips)

Phillips PM3.0×4.0 screw

Color

Silver

Quantity

4

Length

4.0 mm

Thread

3.0 mm

Head diameter

5.0 mm

Phillips PM2.5x10.0 captive screw 107

Where used: 4 screws that secure the hard drive bracket to the hard drive

Slotted Torx ST8M2.5×7.0 screw

Color

Black

Quantity

19

Length

7.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used:

(1) One screw that secures the optical drive to the computer

(2) Twelve screws that secure the switch cover to the computer

108 Chapter 7 Screw listing

Where used: 2 screws that secure the display assembly to the computer

Where used: 3 screws that secure the top cover to the base enclosure

Where used: 1 screw that secures the top cover to the base enclosure

Slotted Torx ST8M2.5×7.0 screw 109

Torx T8M2.5×5.0 broad-head screw

Color

Black

Quantity

2

Length

5.0 mm

Thread

2.5 mm

Head diameter

8.0 mm

Where used: 2 screws that secure the display panel to the display assembly

110 Chapter 7 Screw listing

Torx T8M2.5×4.0 screw

Color

Black

Quantity

1

Length

4.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used: One screw that secures the top cover to the base enclosure

Torx T8M2.5×6.0 screw

Color

Black

Quantity

16

Length

6.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Torx T8M2.5×4.0 screw 111

Where used: 8 screws that secure the display bezel to the display assembly

Where used: Two screws that secure the display panel to the display assembly

Where used:

(1) One screw that secures the system board to the base enclosure

(2) Three screws that secure the battery connector board to the base enclosure

112 Chapter 7 Screw listing

Where used: Two screws that secure the fan to the base enclosure

Torx T8M2.5×6.0 screw 113

Slotted Torx T8M2.0x2.0 screw

Color

Black

Quantity

2

Length

2.0 mm

Thread

2.0 mm

Head diameter

5.0 mm

Where used: 2 screws that secure the switch cover to the base enclosure

114 Chapter 7 Screw listing

Slotted Torx T8M2.5x10.0 screw

Color

Black

Quantity

6

Length

10.0 mm

Thread

2.5 mm

Head diameter

5.0 mm

Where used: 4 screws that secure the switch cover and keyboard to the base enclosure

Where used: 2 screws that secure the display assembly to the base enclosure

Slotted Torx T8M2.5x10.0 screw 115

8 Backup and recovery

Backup and recovery in Windows Vista

Overview

To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.

The Backup and Restore Center provides the following options:

● Backing up individual files and folders

● Backing up the entire hard drive (select models only)

● Scheduling automatic backups (select models only)

● Creating system restore points

● Recovering individual files

● Restoring the computer to a previous state

● Recovering information using recovery tools

NOTE: For detailed instructions, perform a search for these topics in Help and Support.

NOTE: In case of system instability, HP recommends that you print the recovery procedures and save them for later use.

Backing up your information

Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.

You can back up your information to an optional external hard drive, a network drive, or discs.

Note the following when backing up:

● Store personal files in the Documents folder, and back it up regularly.

● Back up templates that are stored in their associated programs.

● Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time-saver if you have to reset your preferences.

116 Chapter 8 Backup and recovery

To create a screen shot:

1.

Display the screen you want to save.

2.

Copy the screen image:

To copy only the active window, press alt+fn+prt sc.

To copy the entire screen, press fn+prt sc.

3.

Open a word-processing document, and then select Edit > Paste.

The screen image is added to the document.

4.

Save the document.

● When backing up to discs, use any of the following types of discs (purchased separately): CD-R,

CD-RW, DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the type of optical drive installed in your computer.

NOTE: DVDs and DVDs with double-layer (DL) support store more information than CDs, so using them for backup reduces the number of recovery discs required.

● When backing up to discs, number each disc before inserting it into the optical drive of the computer.

To create a backup using Backup and Restore Center, follow these steps:

NOTE: Be sure that the computer is connected to AC power before you start the backup process.

NOTE: The backup process may take over an hour, depending on file size and the speed of the computer.

1.

Select Start > All Programs > Maintenance > Backup and Restore Center.

2.

Follow the on-screen instructions to back up your entire computer (select models only) or your files.

NOTE: Windows® includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Performing a recovery

In case of system failure or instability, the computer provides the following tools to recover your files:

● Windows recovery tools: You can use the Backup and Restore Center to recover information you have previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly.

● f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.

The image includes the Windows operating system and software programs installed at the factory.

NOTE: If you are unable to boot (start up) your computer, you must purchase a Windows Vista® operating system DVD to reboot the computer and repair the operating system. For additional information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section in this guide.

Backup and recovery in Windows Vista 117

Using the Windows recovery tools

To recover information you previously backed up, follow these steps:

1.

Click Start > All Programs > Maintenance > Backup and Restore Center.

2.

Follow the on-screen instructions to recover your entire computer (select models only) or your files.

NOTE: Windows includes the User Account Control feature to improve the security of your computer.

You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

To recover your information using Startup Repair, follow these steps:

CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.

All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery.

1.

If possible, back up all personal files.

2.

If possible, check for the presence of the Windows partition and the HP Recovery partition. To find the partitions, select Start > Computer.

NOTE: If the Windows partition and the HP Recovery partition have been deleted, you must recover your operating system and programs using the Windows Vista operating system DVD and the Driver Recovery disc (both purchased separately). For additional information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section in this guide.

3.

Restart the computer, and then press f8 before the Windows operating system loads.

4.

Select Repair your computer.

5.

Follow the on-screen instructions.

NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support.

Using f11

CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.

Software not installed at the factory must be reinstalled.

To recover the original hard drive image using f11 , follow these steps:

1.

If possible, back up all personal files.

2.

If possible, check for the presence of the HP Recovery partition. To find the partition, select

Start > Computer.

NOTE: If the HP Recovery partition has been deleted, you must recover your operating system and programs using the Windows Vista operating system DVD and the Driver Recovery disc (both purchased separately). For additional information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section in this guide.

3.

Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.

118 Chapter 8 Backup and recovery

4.

Press f11 while the “Press <F11> for recovery” message is displayed on the screen.

5.

Follow the on-screen instructions.

Using a Windows Vista operating system DVD (purchased separately)

If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system

DVD to reboot the computer and repair the operating system. Make sure that your most recent backup

(stored on discs or on an external drive) is easily accessible. To order a Windows Vista operating system

DVD, go to http://www.hp.com/support , select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer.

CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process helps you restore the operating system, as well as drivers, software, and utilities.

To initiate recovery using a Windows Vista operating system DVD, follow these steps:

NOTE: This process takes several minutes.

1.

If possible, back up all personal files.

2.

Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before the Windows operating system loads.

3.

When prompted, press any keyboard key.

4.

Follow the on-screen instructions.

5.

Click Next.

6.

Select Repair your computer.

7.

Follow the on-screen instructions.

Backup and recovery in Windows Vista 119

Backup and recovery in Windows XP

Overview

To protect your information, use the Windows® Backup utility (select models only) to back up files and folders or create recovery points. In case of system failure, you can use the backup files to restore your computer.

Windows provides the following options:

● Backing up individual files and folders

● Backing up all files and folders

● Scheduling automatic backups

● Creating recovery points

● Recovering information

NOTE: For detailed instructions, perform a search for these topics in Help and Support.

NOTE: In case of system instability, HP recommends that you print the recovery procedures and save them for later use.

Backing up your information

Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.

You can back up individual files or folders to an optional external hard drive or to a network drive.

Note the following when backing up:

● Store personal files in the My Documents folder, and back it up periodically.

● Back up templates stored in their associated programs.

● Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time saver if you have to reset your preferences.

To copy the screen and paste it into a word-processing document: a.

Display the screen you want to save.

b.

Copy the screen image:

To copy only the active window, press alt+fn+prt sc .

To copy the entire screen, press fn+prt sc .

c.

Open a word-processing document, click Edit > Paste.

The screen image is added to the document.

d.

Save the document.

To create a backup using the Windows Backup utility (select models only), follow these steps:

120 Chapter 8 Backup and recovery

NOTE: Be sure that the computer is connected to AC power before you start the backup process.

NOTE: The backup process may take over an hour, depending on file size and the speed of the computer.

1.

Click Start > All Programs > Accessories > System Tools > Backup.

2.

Follow the on-screen instructions.

Performing a recovery

In case of system failure or instability, the computer provides the following tools to recover your files:

● Windows recovery tools (select models only): You can use the Windows Backup utility to recover information you have previously backed up.

Operating System and Driver Recovery discs (included with your computer): You can use the discs to recover your operating system and programs installed at the factory.

Recovering your information

To recover information you previously backed up, follow these steps:

1.

If possible, back up all personal files.

2.

Click Start > All Programs > Accessories > System Tools > Backup.

The Backup or Restore Wizard opens.

3.

Click Restore files and settings, and then click Next.

4.

Follow the on-screen instructions.

NOTE: For additional information on initiating a recovery in Windows, perform a search for this topic in Help and Support.

Recovering the operating system and programs

CAUTION: The recovery process reformats and completely erases the hard drive. All files you have created and any software installed on the computer are permanently removed. The recovery process reinstalls the original operating system, software, and drivers. Software, drivers, and updates not installed by HP must be manually reinstalled.

To recover your operating system and programs, follow these steps:

1.

If possible, back up all personal files.

2.

Insert the Operating System disc into the optical drive.

3.

Shut down the computer.

4.

Turn on the computer.

5.

Follow the on-screen instructions to install the operating system.

6.

After the operating system is installed, remove the Operating System disc and insert the Driver

Recovery disc.

7.

Follow the on-screen instructions to install the drivers and programs.

Backup and recovery in Windows XP 121

9 Connector pin assignments

Audio-in (microphone)

Pin

1

2

3

Signal

Audio signal in

Audio signal in

Ground

122 Chapter 9 Connector pin assignments

Audio-out (headphone)

Pin

1

2

3

Signal

Audio out, left channel

Audio out, right channel

Ground

Audio-out (headphone) 123

External monitor

Pin

12

13

14

15

8

9

10

11

4

5

6

7

1

2

3

Signal

Red analog

Green analog

Blue analog

Not connected

Ground

Ground analog

Ground analog

Ground analog

+5 VDC

Ground

Monitor detect

DDC 2B data

Horizontal sync

Vertical sync

DDC 2B clock

124 Chapter 9 Connector pin assignments

RJ-11 (modem)

Pin

4

5

6

1

2

3

Signal

Unused

Tip

Ring

Unused

Unused

Unused

RJ-11 (modem) 125

RJ-45 (network)

Pin

1

2

3

4

5

6

7

8

Universal Serial Bus

Signal

Transmit +

Transmit -

Receive +

Unused

Unused

Receive -

Unused

Unused

Pin

3

4

1

2

Signal

+5 VDC

Data -

Data +

Ground

126 Chapter 9 Connector pin assignments

10 Power cord set requirements

The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC.

The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.

Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.

Requirements for all countries and regions

The requirements listed below are applicable to all countries and regions:

● The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).

● All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used.

● The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 250 V AC, as required by the power system of each country or region.

● The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard

Sheet C13 connector for mating with the appliance inlet on the back of the computer.

Requirements for all countries and regions 127

Requirements for specific countries and regions

Country/region Accredited agency Applicable note number

Australia

Austria

Belgium

Canada

Denmark

Finland

France

Germany

Italy

Japan

EANSW

OVE

CEBC

CSA

DEMKO

FIMKO

UTE

VDE

IMQ

METI

1

1

1

3

1

2

1

1

1

1

The Netherlands

Norway

The People's Republic of China

South Korea

Sweden

Switzerland

Taiwan

The United Kingdom

KEMA

NEMKO

CCC

EK

SEMKO

SEV

BSMI

BSI

1

1

5

4

1

1

4

1

The United States UL 2

1.

The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

2.

The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

3.

The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the

Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.

4.

The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

5.

The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

128 Chapter 10 Power cord set requirements

11 Recycling

Battery

When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.

Display

WARNING!

The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury.

CAUTION: The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.

When you remove these components, handle them carefully.

NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org

.

This section provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).

NOTE: The procedures provided in this appendix are general disassembly instructions. Specific details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.

Battery 129

Perform the following steps to disassemble the display assembly:

1.

Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.

2.

Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.

3.

Remove the display bezel (3).

130 Chapter 11 Recycling

4.

Disconnect all display panel cables (1) from the display inverter and remove the display inverter

(2).

5.

Remove all screws (1) that secure the display panel assembly to the display enclosure.

6.

Remove the display panel assembly (2) from the display enclosure.

7.

Turn the display panel assembly upside down.

8.

Remove all screws that secure the display panel frame to the display panel.

9.

Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display panel frame.

Display 131

10.

Remove the display panel frame (2) from the display panel.

11.

Remove the screws (1) that secure the backlight cover to the display panel.

12.

Lift the top edge of the backlight cover (2) and swing it outward.

13.

Remove the backlight cover.

14.

Turn the display panel right-side up.

132 Chapter 11 Recycling

15.

Remove the backlight cables (1) from the clip (2) in the display panel.

16.

Turn the display panel upside down.

WARNING!

The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury.

17.

Remove the backlight frame from the display panel.

Display 133

18.

Remove the backlight from the backlight frame.

19.

Disconnect the display panel cable (1) from the LCD panel.

20.

Remove the screws (2) that secure the LCD panel to the display rear panel.

21.

Release the LCD panel (3) from the display rear panel.

22.

Release the tape (4) that secures the LCD panel to the display rear panel.

23.

Remove the LCD panel.

24.

Recycle the LCD panel and backlight.

134 Chapter 11 Recycling

Index

A

AC adapter, spare part

number 27

AC adapter, spare part

numbers 25

antenna, disconnecting 44

antennae 7

audio, product description 3

audio-in jack

location 12

pin assignments 122

audio-out jack

location 12

pin assignments 123

B

backing up, Windows Vista 116

backing up, Windows XP 120

Backup and Restore

Center 116, 117

base enclosure, spare part

number 19, 28

battery

location 14

removal 40

spare part number 19, 28,

40

battery bay 14

battery connector, system board

spare part number 28

battery extender board, spare part

number 18

battery latches 14

battery light 13

BIOS Administrator password 81

Blu-ray Disc ROM Combo Drive

precautions 33

removal 47

spare part number 19, 24,

28

specifications 87

Bluetooth module

removal 64

spare part numbers 18, 27,

64

Bluetooth module cable,

illustrated 23

boot options 82 boot order 82

bottom components 14

button components 10

buttons

power 10

TouchPad 8, 9

wireless 10

C

Cable Kit

contents 23 spare part number 19, 23,

28

cable, LCD 30

cables, service considerations 33

caps lock light 10

carrying cases, spare part

number 25

chipset, product description 1

CMOS clearing 37

components

bottom 14

buttons 10

front 12

keys 11

left-side 13

lights 10

pointing devices 8

right-side 12

speakers 10

top 7

TouchPad 8

computer feet

locations 39 spare part number 39

Computer Setup

accessing 78

Diagnostics menu 81

File menu 80

navigating and selecting 79 restoring factory settings 79

Security menu 81

System Configuration

menu 82

using 79

computer specifications 84

connectors

power 13

service considerations 33

D

Diagnostics menu 81

discs

Driver Recovery 121

Operating System 121

Disk Sanitizer 81

diskette drive

precautions 33

product description 3

spare part number 25

display assembly

removal 55

spare part number 16, 30,

31, 55

display bezel

removal 57

spare part number 17, 29,

57

display component recycling 129

Index 135

display enclosure, spare part

number 17, 30

display hinge

removal 59

spare part number 17, 29,

59

display inverter

removal 58

spare part number 17, 29,

58

display lid switch module

illustrated 23

display panel, removal 58

display specifications 85

drive light 12

DriveLock password 81

DriveLock, automatic 81

Driver Recovery disc 121

drives

boot order 82

preventing damage 33

DVD-ROM Drive

removal 47

spare part number 19, 24,

28

specifications 90

DVD/CD-RW Combo Drive

precautions 33

removal 47

spare part number 19, 24,

28

specifications 89

DVD±RW SuperMulti Double-layer

Combo Drive

specifications 88

DVD±RW SuperMulti Double-layer

Drive w/LightScribe

precautions 33

removal 47

spare part number 19, 24,

28

E

electrostatic discharge 34

esc key 11

Ethernet, product description 3

Execution Disable 82

ExpressCard assembly

spare part numbers 18

ExpressCard slot 13

ExpressCard slot bezel,

illustrated 22

external media cards, product

description 4

external monitor port

location 13

pin assignments 124

F fan

removal 70

spare part number 18, 29,

70

feet

locations 39 spare part number 39

File menu 80

fn key 11

front components 12

function keys 11

G

graphics, product description 1

grounding equipment and

methods 36

H hard drive

location 14

precautions 33

product description 2

removal 41

spare part number 20, 24,

28, 31, 41

specifications 86

hard drive bay 14

hard drive bay cover

illustrated 22

removal 41

hard drive bracket, removal 42

hard drive test 81

headphone jack

location 12

pin assignments 123

heat sink

removal 74

spare part number 18, 29,

74

hinge

removal 59

spare part number 17, 29,

59

HP Deluxe Nylon Backpack, spare

part number 25, 27

HP Deluxe Roller Case, spare part

number 25, 27

HP Executive Leather Case, spare

part number 25, 27

HP Universal Nylon Case, spare

part number 25, 27

I

I/O address specifications 93

internal display switch 10

interrupt specifications 92

J jacks

audio-in 12 audio-out 12 headphone 12 microphone 12

modem 13 network 13

RJ-11 13

RJ-45 13

K

key components 11

keyboard

product description 4

removal 49

spare part numbers 17, 29,

49

keypad keys 11

keys

esc 11 fn 11 function 11 keypad 11 num lk 11

Windows applications 11

Windows logo 11

L

LAN Power Save 82

language, changing in Computer

Setup 82

LCD cable, spare part number 30

136 Index

left-side components 13

legacy support, Universal Serial

Bus (USB) 78, 82

light components 10

lights

battery 13

caps lock 10

drive 12

power 11

webcam 7

wireless 10

M mass storage devices, spare part

numbers 24

Media Card Reader 12

memory check 81

memory map specifications 95

memory module

product description 1

removal 45

spare part numbers 21, 31,

45

memory module compartment 14

memory module compartment cover

illustrated 22

removal 45

microphone jack

location 12

pin assignments 122

microphone, internal 12

model name 1

modem jack

location 13

pin assignments 125

modem module

product description 3

removal 72

spare part numbers 19, 27,

72

modem, spare part number 18

monitor port

location 13

pin assignments 124

N

navigating in Computer Setup 79

network jack

location 13

pin assignments 126

num lk key 11

O

Operating System disc 121

operating system, product

description 4

optical disc drive connector, system board

spare part number 28

optical drive

location 12

precautions 33

product description 3

removal 47

spare part number 19

spare part numbers 24, 47

specifications 87, 88, 89, 90

optical drive connector board

spare part number 18

P

packing guidelines 35

panels, product description 1

parallel port mode 82

password clearing 37

passwords 81

pin assignments

audio-in jack 122

audio-out jack 123

external monitor port 124

headphone jack 123

microphone jack 122

modem jack 125

monitor port 124

network jack 126

RJ-11 125

RJ-45 jack 126

Universal Serial Bus (USB)

port 126

plastic parts 32

Plastics Kit

contents 22 spare part number 18, 22,

30

pointing device

components 8 illustrated 8

product description 4

pointing device components

TouchPad 8

TouchPad buttons 8, 9

TouchPad scroll zone 8

ports

external monitor 13 monitor 13

product description 4

Universal Serial Bus

(USB) 12, 13

power button 10

power connector 13

power cord

set requirements 127

spare part numbers 25, 30

power light 11

power requirements, product

description 4

processor

product description 1

removal 76

spare part number 30, 31

spare part numbers 18, 76

product description

audio 3

chipset 1

diskette drive 3

Ethernet 3

external media cards 4

graphics 1

hard drives 2

keyboard 4

memory module 1

modem module 3

operating system 4

optical drives 3

panels 1

pointing devices 4 ports 4 power requirements 4

processors 1 product name 1

security 4

serviceability 5

wireless 3

product name 1

Index 137

R removal/replacement

preliminaries 32

procedures 38

restoring Computer Setup factory

settings 79

right-side components 12

RJ-11 jack

location 13

pin assignments 125

spare part number 18

RJ-11 jack cable, illustrated 23

RJ-45 jack

location 13

pin assignments 126

RTC battery

removal 66

spare part number 19, 27,

66

Rubber Kit, spare part number 30

S

Screw Kit

contents 96

spare part number 25, 30

screw listing 96

security cable slot 12

Security menu

Automatic DriveLock 81 change password 81

Disk Sanitizer 81

DriveLock 81 fingerprint reader reset 81

HP Sparekey 81

HP Sparekey enrollment 81 password policy 81

set up BIOS Administrator

password 81

System IDs 81 user management 81

security, product description 4

selecting in Computer Setup 79

serial number 15, 38

service considerations 32

serviceability, product

description 5

speakers

removal 54

spare part number 17, 30,

54

speakers, location 10

specifications

Blu-ray Disc ROM Combo

Drive 87

computer 84

display 85

DVD-ROM Drive 90

DVD/CD-RW Combo Drive 89

DVD±RW Combo Drive 88

hard drive 86

I/O addresses 93

interrupts 92

memory map 95

optical drive 87, 88, 89, 90

system DMA 91

startup check 81

static-shielding materials 36

switch cover

removal 49

spare part number 17, 28,

49

switch, internal display 10

system board

removal 68

spare part numbers 18, 28,

68

System Configuration menu 82

system DMA 91

system fan 82

system IDs 81

system information 80

system memory map 95

T

thermal material, replacement 75

tools required 32

top components 7

top cover

removal 60

spare part number 18, 30,

60

TouchPad 8

TouchPad board, spare part

number 31

TouchPad bracket, spare part

number 18

TouchPad button board, spare part

number 31

TouchPad buttons 8, 9

TouchPad cable, spare part

number 18

TouchPad components 8

TouchPad scroll zone 8

transporting guidelines 35

U

Universal Serial Bus (USB) legacy

support 78, 82

unknown password 37

USB board, removal 63

USB connector and cable, spare

part number 18

USB connectors, spare part

number 28

USB port

location 12, 13

pin assignments 126

V

vents 13, 14

W

webcam light, identifying 7 webcam, identifying 7

Windows applications key 11

Windows Backup utility 120, 121

Windows logo key 11

Windows recovery 117, 121

wireless antenna,

disconnecting 44

wireless antennae 7

wireless button 10 wireless light 10

wireless, product description 3

WLAN module

removal 43

spare part number 28

spare part numbers 19, 27,

43

WLAN module compartment 14

WLAN module compartment cover

illustrated 22

removal 44

workstation guidelines 35

138 Index

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents