43-787.fm Page 1 Monday, August 16, 1999 8:11 AM
Cat. No. 43-787
OWNER’S MANUAL
Please read before using this equipment.
TAD-1027
Digital Telephone Answering System
with Day/Time Voice Stamp
43-787.fm Page 2 Monday, August 16, 1999 8:11 AM
FEATURES
Your RadioShack TAD-1027 Digital
Telephone Answering System with Day/
Time Voice Stamp is a high-quality fullydigital telephone answering device with
touch-tone remote control. Fully digital
means the TAD-1027 stores all messages on a computer chip — there are no
tape mechanisms to wear out and no
tapes to bother with. This gives you capabilities that tape-based answering machines do not have. For example, you
can move quickly from message to message without listening to every one.
The TAD-1027’s 14-minute memory capacity lets you store more messages
than many other TADs (telephone answering devices). And, its unique, spacesaving design makes it ideal for any desk
or nightstand. Your TAD-1027’s remote
control features let you retrieve messages from almost any touch-tone phone.
With an optional pocket tone dialer, you
can even use it from a rotary phone.
Digital Outgoing Message — gives you
a clear outgoing message that can be up
to 60 seconds long.
Digital Incoming Message Storage —
stores incoming messages of up to 60
seconds on a computer chip making it
easy to quickly access the message you
want.
Memory Backup — protects messages
stored in memory in case of a power failure.
Adjustable Ring Selection — lets you
set the TAD-1027 to answer the telephone after four or seven rings.
Toll Saver — lets you avoid unnecessary long-distance charges when you
call long distance to check your messages.
Your TAD-1027’s features include:
Call Screening — lets you listen to incoming calls so you can decide whether
or not to answer.
Voice Day/Time Stamp — announces
the day and time when each message
was recorded.
Phone Pickup Detection — automatically stops the TAD-1027 and resets it if
you answer a call after the TAD answers.
User-Selectable 3-Digit Remote Operation Security Code — helps prevent
unauthorized remote operation.
Memo Recording — lets you leave
memos as messages on the TAD-1027.
© 1997, 1998 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
2
43-787.fm Page 3 Monday, August 16, 1999 8:11 AM
To take advantage of all the TAD-1027’s
features, we recommend that you read
this manual completely before you use
the TAD.
This TAD has been tested and certified
to comply with all applicable UL and FCC
standards.
WARNING: To reduce the risk of
fire or shock hazard, do not expose this product to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you to
the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient
magnitude to constitute a risk of electric shock. Do not open the product’s
case.
!
This symbol is intended to inform you
that important operating and maintenance instructions are included in the
literature accompanying this product.
READ THIS BEFORE
INSTALLATION
Your TAD-1027 conforms to federal regulations, and you can connect it to most
telephone lines. However, each device
you connect to the phone line draws
power from the phone line. We refer to
this power draw as the device’s ringer
equivalence number, or REN. The REN
is on the label on the bottom of the TAD.
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (or
three in rural areas), your phone(s) might
not ring and your TAD might not answer.
If ringer operation is impaired, remove a
device from the line.
FCC STATEMENT
Your TAD-1027 complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC Registration Number
and the REN to your phone company.
Both numbers are on the label on the
bottom of the TAD.
You must not connect the TAD-1027 to
any of the following:
• Coin-operated systems
• Party-line systems
• Most electronic key phone systems
3
43-787.fm Page 4 Monday, August 16, 1999 8:11 AM
CONTENTS
Installation ............................................................................................................. 5
Choosing a Location ......................................................................................... 5
Installing the Backup Battery ............................................................................ 5
Connecting to the Telephone Line .................................................................... 6
Connecting to Power ........................................................................................ 6
Preparation ............................................................................................................
Setting the Day and Time .................................................................................
Recording the Outgoing Message ....................................................................
Setting the Number of Rings ............................................................................
8
8
9
9
Basic Operation .................................................................................................. 10
Setting the TAD-1027 to Answer Calls ........................................................... 10
Recording Incoming Messages ...................................................................... 10
Screening Calls .............................................................................................. 10
Playing Messages .......................................................................................... 11
Repeating Messages ............................................................................... 11
Skipping Messages .................................................................................. 11
Pausing Message Playback ..................................................................... 11
Stopping Message Playback .................................................................... 11
Deleting Messages ......................................................................................... 11
Recording a Memo ......................................................................................... 12
Changing the Remote Operation Security Code ............................................ 12
Remote Operation ............................................................................................... 14
Using Remote Commands ............................................................................. 14
Remote Command Codes ........................................................................15
Troubleshooting .................................................................................................. 16
Resetting the TAD-1027 ................................................................................. 16
Care and Maintenance ........................................................................................ 17
The FCC Wants You to Know ......................................................................... 18
Lightning ......................................................................................................... 18
4
43-787.fm Page 5 Monday, August 16, 1999 8:11 AM
INSTALLATION
CHOOSING A LOCATION
Select a location that is near both a modular telephone jack and an AC outlet.
Note: The TAD cannot answer and
record incoming calls without AC power.
Follow these steps to install the backup
battery.
Your TAD-1027 connects directly to a
modular telephone line jack. If the telephone line jack is not a modular jack, you
must update the wiring. You can convert
the wiring yourself, using jacks and
adapters available at your local RadioShack store. Or, you can let the telephone company update the wiring for
you. The USOC number of the jack to be
installed is RJ11C.
1. Slide the battery compartment cover
in the direction of the arrow, then lift
off the cover.
INSTALLING THE
BACKUP BATTERY
2. Snap the battery’s contacts firmly to
the TAD-1027’s connector and place
the battery into the compartment.
The TAD requires AC power to operate.
However, if AC power fails or you unplug
the TAD-1027, a 9-volt backup battery
(not supplied) saves the messages and
the settings for the day, time, and remote
operation security code. We recommend
you use an alkaline battery, such as RadioShack Cat. No. 23-553.
Warning: If the TAD’s modular line cord
is already connected to the telephone
line jack, disconnect it before you install
the backup battery. This reduces the risk
of electric shock.
Illus. showing removal
of battery compartment
cover.
Illus. showing
connection of connector
to battery terminals.
3. Replace the cover.
Caution: Always use a fresh battery of
the required size and recommended
type.
5
43-787.fm Page 6 Monday, August 16, 1999 8:11 AM
CONNECTING TO THE
TELEPHONE LINE
To connect the TAD-1027 to the phone
line, plug one end of the supplied modular telephone cord into the TO LINE jack.
Then plug the other end into a modular
phone jack.
Illus. of TO LINE jack
and connection to a
modular jack.
You can connect a telephone to the TO
TEL jack using a second modular telephone cord (not supplied).
Illus. of TO SET jack
and connection to a
phone. Show other
phone cord already
connected.
6
CONNECTING TO POWER
Note: Adjust VOLUME to the middle position before connecting power.
Illus. of VOLUME
switch.
Insert the supplied AC adapter’s barrel
plug into the AC 9V/440mA jack on the
back of the TAD-1027. Then plug the
adapter’s other end into a standard AC
outlet.
Illus. of AC 9V/440mA
jack. Show other
phone cords already
connected.
Caution: The supplied adapter supplies
9 volts AC, delivers at least 440 milliamps, and has a plug which properly fits
the TAD-1027’s AC 9V/440mA jack. Using an adapter that does not meet these
specifications might damage the TAD or
the adapter.
43-787.fm Page 7 Monday, August 16, 1999 8:11 AM
When you first connect power, the PLAY/
SKIP indicator flashes rapidly (until you
record the outgoing message), the ANSWER indicator flashes (until you install
a backup battery), and the TAD-1027 automatically runs a self-test. You cannot
operate the TAD during this test. When
the test is complete, the TAD-1027
beeps once and announces, “Answer
off.”
Illus. of ANSWER and
PLAY/SKIP indicators.
When the battery is weak or not installed,
the ANSWER indicator flashes and
pauses, flashes and pauses, until you install a fresh battery. Be sure the AC
adapter’s cord is plugged in so you do
not lose the TAD-1027’s stored information, then replace the battery.
Caution: Dispose of
promptly and properly.
old
batteries
7
43-787.fm Page 8 Monday, August 16, 1999 8:11 AM
PREPARATION
SETTING THE DAY AND
TIME
Follow these steps to set the current day
and time so the TAD-1027 records the
correct day and time of the call with each
phone message.
Note: If you do not complete each step
within 8 seconds, the TAD-1027 sounds
a three-tone beep and stops setting the
day and time. Start again at Step 1.
1. Use a straightened paper clip to
hold down CLOCK until the TAD1027 beeps. The TAD then
announces, “Sunday.”
Illus. showing OGM/REPEAT
and PLAY/SKIP.
3. Press ANSWER/STOP/DELETE. The
TAD-1027
beeps
once
and
announces the hour and “AM” or
“PM.”
Illus. showing ANSWER/
STOP/DELETE.
Illus. showing CLOCK
switch.
Note: If necessary, adjust VOLUME .
2. To change the day of the week,
repeatedly press OGM/REPEAT to
move backward or PLAY/SKIP to
move forward until the TAD
announces the desired day of the
week.
4. To change the hour, repeatedly
press OGM/REPEAT to move backward or PLAY/SKIP to move forward
to the desired hour.
5. Press ANSWER/STOP/DELETE. The
TAD-1027 beeps once and announces the minutes.
6. To change the minutes, repeatedly
press OGM/REPEAT to move backward or PLAY/SKIP to move forward
to the desired minute.
Note: You can hold down OGM/
REPEAT or PLAY/SKIP to move the
minutes in 10-minute increments.
8
43-787.fm Page 9 Monday, August 16, 1999 8:11 AM
7. When you finish, press ANSWER/
STOP/DELETE to confirm the settings. The TAD-1027 beeps and
announces the day and time.
To check the current day/time, use a
straightened paper clip to press CLOCK.
RECORDING THE
OUTGOING MESSAGE
Before you can set the TAD-1027 to answer calls, you must record the outgoing
message (OGM) the caller hears when
the TAD answers a call. Your outgoing
message can be up to 60 seconds long.
1. Hold down OGM/REPEAT until the
TAD-1027 beeps.
Note: If memory is full, the PLAY/
SKIP indicator flashes, the TAD1027 announces, “Memory is full,”
and you cannot record the outgoing
message. Delete old messages to
make room in memory (see “Deleting Messages” on Page 11).
Important: Do not tell callers you
are not home. Instead, say that you
cannot come to the phone right now.
3. The TAD-1027 automatically stops
recording after 60 seconds, or you
can press ANSWER/STOP/DELETE
when you finish the message. The
TAD-1027 beeps and automatically
plays back the outgoing message.
To play the outgoing message at any
time, press OGM/REPEAT. If no outgoing
message is recorded, the TAD-1027
says, “No announcement.”
SETTING THE NUMBER
OF RINGS
The ring select 4/7/TS switch controls
how long the TAD-1027 waits before it
answers a call. Slide the switch to the appropriate position.
Illus. showing
4/7/TS switch.
2. Speak in a normal voice about 8
inches away from the microphone
on the front of the TAD.
Illus. showing
microphone.
Microphone
Ask for the caller’s name, phone
number, and message.
4 — The TAD-1027 answers after four
rings.
7 — The TAD-1027 answers after seven
rings.
TS (Toll Saver) — If there are new messages, the TAD-1027 answers after two
rings. Otherwise, the TAD answers after
four rings.
9
43-787.fm Page 10 Monday, August 16, 1999 8:11 AM
BASIC OPERATION
SETTING THE TAD-1027
TO ANSWER CALLS
To set the TAD-1027 to answer calls,
press ANSWER/STOP/DELETE.
• If an outgoing message is recorded,
the TAD-1027 announces, “Answer
on,” and the ANSWER indicator
lights.
• If no outgoing message is recorded,
the TAD-1027 says, “Answer off, no
announcement” (see “Recording the
Outgoing Message” on Page 9).
To have the TAD-1027 not answer calls,
press ANSWER/STOP/DELETE again.
The TAD announces, “Answer off,” and
the ANSWER indicator turns off.
RECORDING INCOMING
MESSAGES
Each incoming message can be up to 60
seconds long.
The TAD hangs up and resets to answer
the next call when:
• The caller hangs up.
• The maximum message length (60
seconds) is reached.
10
• There are more than 8 seconds of
silence.
• You pick up any phone on the same
phone line as the TAD (see “Screening Calls”).
Note: The PLAY/SKIP indicator flashes
when a new message is recorded. After
the new message is played, the PLAY/
SKIP indicator lights.
SCREENING CALLS
To screen calls, let the TAD-1027 answer them, then listen to the caller’s
message through the TAD’s speaker. If
you decide to answer the call, pick up
any phone on the same phone line as
the TAD. The TAD stops recording and
resets to answer the next call.
Note: If you pick up the phone just as the
TAD-1027 answers, the TAD might not
stop playing the outgoing message. If
this happens, press ANSWER/STOP/DELETE to stop the TAD.
If you do not want to take the call, do not
pick up the handset, and let the TAD1027 finish recording the caller’s message.
43-787.fm Page 11 Monday, August 16, 1999 8:11 AM
PLAYING MESSAGES
Skipping Messages
If there are new messages, the PLAY/
SKIP indicator flashes until all the new
messages have been played.
To skip to the next message during playback, press PLAY/SKIP once. The next
recorded message plays.
To play all the messages, press PLAY/
SKIP. The TAD-1027 announces the
Pausing Message Playback
number of messages or if there are no
messages stored, the TAD announces,
“No message.”
Illus. showing PLAY/SKIP.
To pause message playback, press ANSWER/STOP/DELETE. To resume playing
messages, press PLAY/SKIP. Otherwise,
after pausing for 60 seconds, the TAD1027 sounds three beeps and stops
playback.
Stopping Message Playback
To stop playback at any time, press ANSWER/STOP/DELETE twice. The TADBefore playing each message, the TAD1027 announces the message number
and the day and time when the message
was recorded. After all messages play,
the TAD announces, “End of message(s)” then it resets to answer calls.
Repeating Messages
To replay a message, if you have listened to at least 5 seconds of it, press
OGM/REPEAT. The current message
starts again.
1027 beeps once and resets to answer
calls.
DELETING MESSAGES
To delete all the messages you have already listened to, while playback is
stopped, hold down ANSWER/STOP/DELETE . The TAD-1027 sounds a long
beep then deletes all old messages, but
keeps any new messages (and the
PLAY/SKIP indicator continues flashing).
If you have not listened to 5 seconds of
the message, or the message is not at
least 5 seconds long, pressing OGM/REPEAT replays the previous message.
11
43-787.fm Page 12 Monday, August 16, 1999 8:11 AM
Notes:
• If you have played only a portion of
a message, the TAD-1027 might not
delete it.
• Individual messages can only be
deleted by remote operation.
RECORDING A MEMO
A memo is a message you can record at
the TAD-1027 without having to call in on
a phone.
Notes:
• The maximum memo length is 60
seconds.
• When memory is full, the TAD-1027
announces, “Memory is full,” and
you cannot record the memo. Delete
old messages to make room in
memory (see “Deleting Messages”
on Page 11).
Follow these steps to record a memo.
1. Hold down PLAY/SKIP until the TAD1027 beeps.
2. Speak in a normal voice into the
microphone on the front of the TAD.
3. The TAD-1027 automatically stops
recording after 60 seconds, or you
can press ANSWER/STOP/DELETE
when you finish the memo. The
TAD-1027 beeps once.
12
The memo is recorded along with the incoming messages. To hear the memo,
simply play back your messages.
CHANGING THE REMOTE
OPERATION SECURITY
CODE
The TAD’s remote operation security
code is preset to 787. You can operate
your TAD-1027 remotely with this code;
however, we recommend that you set
your own code.
Notes:
• Be sure to set each digit within 8
seconds. Otherwise, you must start
over from Step 1.
• If the AC power fails or if the backup
battery becomes weak, the remote
operation security code automatically resets to 787.
1. Use a pointed object, such as a
straightened paper clip, to hold
down CODE until the TAD-1027
beeps and announces the first digit
of the current security code.
Illus. showing
CODE switch.
43-787.fm Page 13 Monday, August 16, 1999 8:11 AM
2. Repeatedly
press PLAY/SKIP or
OGM/REPEAT to set the first digit,
then press ANSWER/STOP/DELETE.
The TAD-1027 beeps and
nounces the second digit.
an-
press PLAY/SKIP or
OGM/REPEAT to set the second
digit, then press ANSWER/STOP/
DELETE. The TAD-1027 beeps and
3. Repeatedly
announces the third digit.
press PLAY/SKIP or
OGM/REPEAT to set the third digit,
then press ANSWER/STOP/DELETE.
4. Repeatedly
The TAD-1027 beeps once and
announces the complete remote
operation security code.
13
43-787.fm Page 14 Monday, August 16, 1999 8:11 AM
REMOTE OPERATION
You can operate the TAD-1027 from almost any touch-tone phone, or from a rotary phone using a pocket tone-dialer
(available at your local RadioShack
store).
Notes:
• When the memory is full, the TAD1027 answers the call after two
rings and announces, “Memory is
full.” Delete some of the old messages to make room in memory
(see “Using Remote Commands”).
• If the ring select switch is set to TS
(toll saver), the TAD-1027 answers
after two rings if you have new messages (ones you have not played). If
there are no new messages, the
TAD waits for four rings before it
answers. This gives you time to
hang up before the TAD-1027
answers so you can avoid unnecessary long-distance charges.
USING REMOTE
COMMANDS
Notes:
• The TAD-1027 sounds a 3-tone
beep if you press the wrong button.
• You must record an outgoing message before you can remotely set
the TAD-1027 to answer calls.
1. Dial your phone number.
• If the TAD-1027 is set to answeroff and an outgoing message is
recorded, it answers the call after
10 rings and announces, “Answer
off.”
• If the TAD-1027 is set to answeron, it answers according to the
number of rings you set.
2. Within 8 seconds, enter the remote
operation security code. The TAD
beeps.
Note: If you do not enter each digit
of the security code within 8 seconds, the TAD-1027 will disconnect.
3. Enter the remote command code
(see “Remote Command Codes” on
Page 15).
4. You can hang up at this point or
enter other remote command(s).
14
43-787.fm Page 15 Monday, August 16, 1999 8:11 AM
Remote Command Codes
After you press 4 (to play all messages):
Press:
To:
Press:
0
Stop message playback or
recording.
6
Delete the current message.
1
Play the outgoing message.
7
Replay the previous message.
2
Record a new outgoing
message. When the TAD1027 announces “Record
announcement,” begin
speaking. When you finish,
press 0. The TAD repeats
the OGM.
8
Replay the current message.
9
Skip forward to the next
message.
0
Stop message playback.
4
Play all the recorded messages.
6
Delete all old messages.
#
Set the TAD-1027 to
answer or not answer calls.
To:
15
43-787.fm Page 16 Monday, August 16, 1999 8:11 AM
TROUBLESHOOTING
If you have problems using your TAD-1027, try the suggestions in this section. If you
still have problems, contact your local RadioShack store for assistance.
Problem
The incoming message is incomplete.
Suggestion
Be sure the memory is not full.
The caller’s message was longer than 60 seconds.
The caller was silent for over 8 seconds.
The incoming message is
unclear.
Adjust VOLUME.
The TAD-1027 does not answer
after two, four, or seven rings.
Be sure the TAD is set to answer calls.
ANSWER indicator flashes.
The backup battery is weak or missing.
Replace the battery (see “Installing the Backup
Battery” on Page 5).
The TAD-1027 does not respond
to the remote operation security
code.
Make sure the phone you used to dial the TAD
is a touch-tone phone. (If it is not, you can use
a pocket tone dialer to enter the code and commands.)
Re-enter your remote operation security code.
The remote operation security code might have
reset to the default code due to a power failure.
Make sure the code you entered is correct.
You cannot record an incoming
message.
Be sure the TAD-1027 is set to answer calls.
Be sure the memory is not full.
RESETTING THE TAD-1027
If your TAD-1027 stops working properly, remove the AC adapter and the battery from
the TAD, then reinstall them.
Note: The outgoing messages and all information stored in memory are erased when
you reset the TAD.
16
43-787.fm Page 17 Monday, August 16, 1999 8:11 AM
CARE AND MAINTENANCE
Your RadioShack TAD-1027 Digital Telephone Answering System with Day/Time
Voice Stamp is an example of superior design and craftsmanship. The following suggestions will help you care for the TAD-1027 so you can enjoy it for years.
Keep the TAD-1027 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the TAD-1027 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.
Keep the TAD-1027 away from dust and dirt, which can cause premature wear of parts.
Handle the TAD-1027 gently and carefully. Dropping it can damage circuit boards and cases and can cause the TAD to work improperly.
Use only a fresh battery of the required size and type. Batteries can leak
chemicals that damage your TAD-1027’s electronic parts.
Wipe the TAD-1027 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the TAD.
Modifying or tampering with the TAD-1027’s internal components can cause a malfunction and might invalidate your TAD’s warranty and void your FCC authorization to
operate it. If your TAD-1027 is not performing as it should, take it to your local RadioShack store for assistance. If the trouble is affecting the telephone lines, the phone
company can ask you to disconnect your TAD until you have resolved the problem.
17
43-787.fm Page 18 Monday, August 16, 1999 8:11 AM
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your TAD-1027
causes problems on the telephone line,
the telephone company can temporarily
discontinue your service. If this happens,
the telephone company attempts to notify you in advance. If advance notice is
not practical, the telephone company notifies you as soon as possible and advises you of your right to file a complaint
with the FCC.
Also, the telephone company can make
changes to its lines, equipment, operations, or procedures that could affect the
operation of this TAD. The telephone
company notifies you of these changes
in advance so you can take the necessary steps to prevent interruption of your
telephone services.
Your TAD-1027 complies with the limits
for a Class B digital device as specified in
Part 15 of FCC Rules. These limits provide reasonable protection against radio
and TV interference in a residential area.
However, your TAD might cause TV or
radio interference even when it is operating properly.
18
To eliminate interference, you can try
one or more of the following corrective
measures:
• Reorient or relocate the receiving
radio or TV antenna.
• Increase the distance between the
TAD-1027 and the radio or TV.
• Use outlets on different electrical circuits for the TAD-1027 and the radio
or TV.
Consult your local RadioShack store if
the problem still exists.
LIGHTNING
Your TAD-1027 has built-in protection
circuits to reduce the risk of damage
from surges in telephone line and power
line current. These protection circuits
meet or exceed the FCC requirements.
However, lightning striking the telephone
or power lines can damage your TAD.
Lightning damage is not common. Nevertheless, if you live in an area that has
severe electrical storms, we suggest that
you unplug the TAD-1027 during storms
to reduce the possibility of damage.
43-787.fm Page 19 Monday, August 16, 1999 8:11 AM
NOTES
19
43-787.fm Page 20 Monday, August 16, 1999 8:11 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
1A8
Printed in China