HK
<P=001>
PORTABLE CD STEREO SYSTEM
MODEL
QT-CD250H
OPERATION MANUAL
Thank you for purchasing this SHARP product.
For the best performance, read this manual carefully. It will guide you in operating your SHARP
product.
NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS
1362 fuse marked
or
and of the same rating as
above, which is also indicated on the pin face of the plug
must be used.
Always refit the fuse cover after replacing the fuse. Never
use the plug without the fuse cover fitted.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug.
Before replacing the plug cover, make sure that:
● If the new fitted plug contains a fuse, its value is the
same as that removed from the cut-off plug.
● The cord grip is clamped over the sheath of the mains
lead and not simply over the lead wires.
In the unlikely event of the socket outlet in your home
not being compatible with the plug supplied, cut-off the
mains plug and fit an appropriate type.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED
ELECTRICIAN.
DANGER:
SERVICE INFORMATION
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious
electric shock may occur.
In the unlikely event of your equipment requiring repair,
please contact the dealer or supplier from whom it was
purchased. Where this is not possible, please contact
the telephone number listed below. You will then be
given details of how to obtain service.
- 0345-125387 Please note; all calls will be charged at local rate.
To fit an appropriate plug to the mains lead, follow the
instructions below:
Certain replacement parts and accessories may be obtained from our main parts distributor.
The fuse from the cut-off plug should be removed and
the cut-off plug destroyed immediately and disposed of
in a safe manner.
IMPORTANT:
WILLOW VALE ELECTRONICS LTD.
The wires in the mains lead are coloured in accordance
with the following code:
Blue
Brown
: Neutral
: Live
As the colours of the wires in the mains lead of this
product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
● The wire which is coloured blue must be connected to
the plug terminal which is marked N or coloured black.
● The wire which is coloured brown must be connected
to the plug terminal which is marked L or coloured red.
MANCHESTER 0161-682-1415
READING
01189-876444
In the unlikely event of this equipment requiring repair
during the guarantee period, you will need to provide
proof of the date of purchase to the repairing company.
Please keep your invoice or receipt, which is supplied at
the time of purchase.
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
TO
<P=001>
SPECIAL NOTES
● The letters in brackets contained in the model
number indicate the colour of the product only.
Operation and specifications are unaffected.
● Recording and playback of any material may
require consent, which SHARP is unable to give.
Please refer particularly to the provisions of the
Copyright Act 1956, the Dramatic and Musical
Performers Protection Act 1958, the Performers
Protection Acts 1963 and 1972 and to any subsequent statutory enactments and orders.
Warning:
To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing. No objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Caution:
Use of controls, adjustments or performance of procedures other than those specified herein may result
in hazardous radiation exposure.
● This equipment complies with the requirements
of Directives 89/336/EEC and 73/23/EEC as
amended by 93/68/EEC.
As the laser beam used in this compact disc player
is harmful to the eyes, do not attempt to disassemble
the cabinet. Refer servicing to qualified personnel
only.
● When the ON/STAND-BY switch is set at
STAND-BY position, mains voltage is still present inside the unit.
Warning:
This unit contains no user serviceable parts. Never
remove covers unless qualified to do so. This unit
contains dangerous voltages, always remove mains
plug from the socket before any service operation
and when not in use for a long period.
ACCESSORIES
AC power lead × 1
Remote control × 1
Notes:
● The AC power lead and remote control are located in the packing material.
● Parts and accessories mentioned in this operation manual other than those in the drawing are not
included.
1
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=002>
PRECAUTIONS
■ General
■ Battery use
● Do not use oil, solvents, petrol, paint thinners or
insecticides on the unit.
● Do not expose the unit to moisture, to temperatures higher than 60˚C (140˚F) or to extreme low
temperatures.
● Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers, facsimiles, etc.) which generates electrical
noise.
● Hold the AC power plug by the head when removing it from the AC socket, as pulling the lead
can damage internal wires.
● When cleaning the heads, pinch roller, etc,
remove the AC power plug from the wall socket
as the unit contains high voltages.
Do not remove the outer cover, as this may result
in electric shock. Refer internal service to your
local SHARP service facility.
● Use the unit on a firm, level surface free from
vibration, and do not place anything on the top
of the unit.
● If the unit does not work properly whilst in use,
set the ON/STAND-BY switch to STAND-BY and
then to ON again.
● If an electrical storm is taking place near you, it
is suggested that you disconnect the AC power
lead from the AC socket for safety.
● The ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers, tablecloths, curtains, etc.
● No naked flame sources, such as lighted candles, should be placed on the apparatus.
● Attention should be drawn to the environmental
aspects of battery disposal.
● The apparatus is designed for use in moderate
climate.
Warning:
The voltage used must be the same as that specified
on this unit. Using this product with a higher voltage
other than which is specified is dangerous and may
result in a fire or other type of accident causing
damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
● Replace all old batteries with new ones at the
same time.
● Do not mix old and new batteries.
● Remove the batteries if they are weak or if the
unit will not be used for long periods of time. This
will prevent potential damage due to battery
leakage.
● Batteries are not included.
Caution:
● Do not use rechargeable batteries (nickel-cadmium battery, etc.).
■ Care of compact discs
Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation
of dirt on the disc surface.
Follow the guidelines below for maximum enjoyment
from your CD collection and player.
● Do not write on either side of the disc, particularly
the non-label side. Signals are read from the
non-label side. Do not mark this surface.
● Keep your discs away from direct sunlight, heat,
and excessive moisture.
● Always hold the CDs by the edges. Fingerprints,
dirt, or water on the CDs can cause noise or
mistracking. If a CD is dirty or does not play
properly, clean it with a soft, dry cloth, wiping
straight out from the centre, along the radius.
■ Cassette tape
● For playback, use normal or low-noise tape for
the best sound. (Metal or CrO2 tape is not recommended.)
For recording, use only normal tape.
● Do not use C-120 tapes, tapes with large
diameter reels, or poor-quality tapes, as they
may cause malfunctions.
● Before loading a tape into the cassette compartment, tighten the slack with a pen or pencil.
● Cassettes have removable tabs which prevent
accidental recording or erasing from taking
place. Removing the tab will protect the corresponding side from being erased. Cover the tab
holes with adhesive tape to erase or record
again.
■ Condensation
Sudden temperature changes, storage or operation
in an extremely humid environment may cause condensation inside the cabinet (CD pickup, tape
heads, etc.) or on the transmitter LED on the remote
control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc (or
cassette) in the unit until normal playback is possible
(about 1 hour). Wipe off any condensation on the
transmitter LED with a soft cloth before operating the
unit.
Warning:
CD players use a laser pickup which can damage
the eyes if viewed directly. Do not look at the pickup,
and do not touch the pickup directly.
Side A (1)
Tab for side B (2)
2
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
Tab for side A (1)
<P=003>
NAMES OF CONTROLS AND INDICATORS
1
2 3 4 5 6
7
8
9
10
26 27
14
15
11
12
28 29
30
16
13
17
18
19
11.
12.
13.
14.
15.
16.
17.
18.
19.
10.
3
11.
3
12.
13.
14.
3
15.
3
16.
3
17.
18.
19.
20.
20 21 22 23
(TAPE) Record Button
(TAPE) Play Button
(TAPE) Rewind Button
(TAPE) Fast Forward Button
(TAPE) Stop/Eject Button
(TAPE) Pause Button
Cassette Compartment
CD Compartment
CD Eject Button
(CD) Stop Button
(TUNER) Tuning Down Button
(CD) Repeat Button
(TUNER) Band Selector Button
(TUNER) Preset Memory Button
Extra Bass Button
(CD) Play/Pause Button
(TUNER) Tuning Up Button
(CD) Track Up/Cue Button
(TUNER) Preset Up Button
(CD) Track Down/Review Button
(TUNER) Preset Down Button
Volume Up/Down Buttons
Stand-by, On/Function Switch
(CD) Play Indicator
(CD) Repeat Indicator
24
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
3
32.
3
33.
3
34.
3
35.
36.
37.
3
38.
39.
25
34
39
(CD) Pause Indicator
Extra Bass Indicator
(TUNER) Memory Indicator
(TUNER) FM Stereo Mode Indicator
(TUNER) FM Stereo Indicator
Battery Compartment
FM Telescopic Rod Aerial
Headphone Socket
AC Power Input Socket
Backup Memory Battery Compartment
(CD) Play/Pause Button
(TUNER) Tuning Up Button
(CD) Track Down/Review Button
(TUNER) Preset Down Button
(CD) Stop Button
(TUNER) Tuning Down Button
(CD) Repeat Button
(TUNER) Band Selector Button
(TUNER) Memory Button
(TUNER) Clear Button
(CD) Track Up/Cue Button
(TUNER) Preset Up Button
Extra Bass Button
Volume Up/Down Buttons
3
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
32
33
35
36
37
38
31
<P=001>
TO
POWER SOURCE
■ Battery power
■ AC power
AC 230-240 V, 50 Hz
2
3
1
5
To AC INPUT
6
4
To an AC socket
Connect the AC power lead to the AC power input
socket, then connect the AC power lead plug to an
AC socket.
1
Disconnect the AC power lead, and remove the
battery compartment cover.
2
Insert 6 "D" size batteries (UM/SUM-1, R20,
HP-2 or similar) into the battery compartment.
● Insert the batteries according to the direction
indicated on the rear panel.
● When inserting or removing the batteries ③ and
⑥, push them towards the battery terminals.
● Installing the batteries incorrectly may cause the
unit to malfunction.
Notes:
● If the unit will not be used for a long period of
time, remove the AC power lead from the AC
socket.
● Connection of the AC power lead to the unit
disconnects the batteries.
● Never use a power lead other than the one
supplied. Use of a power lead other than the one
supplied may cause an electric shock or fire.
ë
3
Replace the battery compartment cover.
Note:
Replace the batteries when they become weak
and/or recording or playback is impaired. This may
occur even though radio broadcasts are audible.
REMOTE CONTROL
1
Remove the battery compartment cover on the
remote control.
2
Insert 2 "AA" size batteries (UM/SUM-3, R6,
HP-7 or similar) into the battery compartment on
the remote control.
● When inserting or removing the batteries, push
them towards the battery terminals.
● Installing the batteries incorrectly may cause the
unit to malfunction.
ë
Remote sensor
Notes:
● Replace the batteries if the operating distance is
reduced or if the operation becomes erratic.
● Periodically clean the transmitter LED on the
remote control and the sensor on the main unit
with a soft cloth.
● Exposing the sensor on the main unit to strong
light may interfere with operation. Change the
lighting or the direction of the unit.
● Keep the remote control away from moisture,
excessive heat, shock, and vibrations.
15
15
0.2 m - 6 m
(8" - 20’)
4
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=002>
COMPACT DISC OPERATION
2
4
3
REPEAT
BAND
STOP
TUNING
PLAY / PAUSE
TUNING
/
PRESET
TUNING
/
PRESET
BAND
TUNING
ON/STAND-BY
(Function)
REVIEW
PRESET
CUE
PRESET
■ CD playback
1
2
To interrupt playback:
Press the PLAY/PAUSE (0 6) button during playback.
Press the PLAY/PAUSE (0 6) button again to
resume playback.
Set the function switch to CD.
Press the CD EJECT button to open the CD
compartment.
3
Place a compact disc on the spindle, label side
up.
● 8 cm (3") discs may be played without an adaptor.
4
To stop playback:
Press the STOP (■) button.
Close the CD compartment by firmly pushing the
right corner of it.
Total number of
tracks
Precautions:
● When "no dISC" or track number is displayed,
the power is connected.
If you will not be using the CD player, set the
ON/STAND-BY switch to STAND-BY.
● Do not open the CD compartment whilst the
disc is rotating.
● If the disc is damaged, dirty, or loaded upside
down, "Er" or "no dISC" will appear in the
display.
Clean, replace, or reload the disc properly.
● Keep foreign objects out of the CD compartment.
● Subjecting the unit to shock or vibration may
cause mistracking.
● Keep the CD compartment closed except
when loading discs.
● Playing certain compact discs at a high volume may cause mistracking. In this case,
listen at a lower volume.
● The temperature range for playing compact
discs is recommended to be 5˚C (41˚F) - 35˚C
(95˚F).
● If TV or radio interference occurs during CD
operation, move the unit away from the TV or
radio.
Total playing time
5
Press the PLAY/PAUSE (0
playback from track 1.
6
Press the VOLUME W button to increase the
volume and the VOLUME X button to decrease
the volume.
7
Press the X-BASS button to emphasise the bass
region of the frequency spectrum.
The "X-BASS" indicator will light up.
Press the X-BASS button again to cancel the
extra bass mode.
The "X-BASS" indicator will go out.
6
) button to start
5
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=003>
(Continued)
■ Repeat play
REPEAT
BAND
STOP
TUNING
REVIEW
PRESET
/
PRESET
PLAY / PAUSE
TUNING
During playback, press the REPEAT/BAND ( R) button repeatedly to select the play mode.
Each time the button is pressed, the display will
change as follows:
CUE
PRESET
Flashes
1 track repeat play
Appears
All track repeat play
Disappears
Normal play
Repeat indicator
TUNING
/
PRESET
BAND
TUNING
Note:
● When using repeat play, be sure to press the
STOP (■) button after you are through listening.
Otherwise, the CD(s) will play continuously.
■ APSS (Auto Program Search System)
APSS automatically locates the beginning of any
track.
■ Cue and review
To listen again to the track being played:
Press the DOWN (3 / 5) button for less than 0.5
seconds during playback.
1
2
Load a disc and begin playback.
To move to the beginning of the next track:
Press the UP (2 / 4) button for less than 0.5
seconds during playback.
3
Normal playback will resume when the REVIEW
(3 / 5) or CUE (2 / 4) button is released.
Hold down the CUE (2 / 4) button for audible
fast forward, and hold down the REVIEW (3 /
5) button for audible fast reverse.
Notes:
● When the end of the disc is reached whilst
cueing, "End" will appear in the display and CD
operation is paused. Press the REVIEW (3 /
5) button for fast reverse or press the STOP
(■) button to stop CD operation.
● If the beginning of the disc is reached whilst
reviewing, the mode will automatically switch to
normal playback at that point.
Notes:
● To skip a number of tracks at one time, press the
UP (2 / 4 ) or DOWN (3 / 5 ) button
repeatedly until the desired track number is
shown.
● To start playback from a desired track, press the
UP (2 / 4) or DOWN (3 / 5) button whilst
in the stop mode to select the track number, and
then press the PLAY/PAUSE (0 6) button.
6
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=004>
Precautions:
● Be sure not to press the PLAY and REWIND
buttons simultaneously, or the tape will become
damaged.
● Before changing from one tape operation to another, press the STOP/EJECT button.
● Do not press the PAUSE button whilst the fast
forward or rewind operations are in progress.
The F FWD or REWIND button will not be released when the tape end is reached. Once this
occurs, press the STOP/EJECT button.
CASSETTE OPERATION
HEADPHONES
ON/STAND-BY
(Function)
● Before plugging in or unplugging the headphones, make sure the volume level is reduced.
● Be sure your headphones have a 3.5 mm (1/8")
diameter plug and are between 16 ohms and 50
ohms impedance. The recommended impedance is 32 ohms.
● Connect the headphones plug to the PHONES
socket located on the rear of the unit. The speakers will be automatically disconnected. Adjust
the volume by using the VOLUME control.
■ Tape playback
1
2
Set the function switch to TAPE.
3
4
Press the PLAY button.
Load the cassette into the cassette compartment.
To advance the tape, press the STOP/EJECT
button, then press the F FWD button. To rewind,
press the STOP/EJECT button, then press the
REWIND button.
To interrupt playback:
Press the PAUSE button during playback.
Press the PAUSE button again to resume playback.
To stop playback:
Press the STOP/EJECT button.
7
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=005>
RADIO OPERATION
REPEAT
BAND
STOP
TUNING
PLAY / PAUSE
TUNING
TUNER
MEMORY
/
PRESET
CLEAR
TUNING
/
PRESET
BAND
TUNING
TUNER
MEMORY
ON/STAND-BY
(Function)
REVIEW
PRESET
CUE
PRESET
Notes:
● When radio interference occurs during auto scan
tuning, auto scan tuning may stop automatically
at that point.
● If a weak station signal is found during auto scan
tuning, the station will be skipped.
● To stop the auto tuning, press the TUNING (
or ) button again.
● If the FM reception is poor, press the REPEAT/BAND ( ) button so that the "ST" indicator goes out.
Although the reception changes to monaural, the
sound becomes clearer.
■ Tuning
1
2
Set the function switch to TUNER.
R
Press the REPEAT/BAND ( ) button to select
the desired frequency band. (FM ST, FM or AM)
W
FM STEREO
FM MONO
X
R
Aerial adjustment:
AM
FM
AM
● To receive an FM stereo transmission, press the
REPEAT/BAND ( ) button so that the "ST" indicator on the display lights up.
● The " " indicator lights up when an FM broadcast is in stereo.
j
R
After use:
Set the ON/STAND-BY switch to STAND-BY.
3
X or W) button to tune into
Press the TUNING (
the desired station.
Manual tuning:
Press the TUNING ( or ) button as many times
as required to adjust the frequency shown on the
display to the frequency of the desired station.
X W
Auto tuning:
When the TUNING ( or ) button is pressed for
more than 0.5 seconds, scanning will start automatically and the tuner will stop at the first receivable
broadcast station.
X W
8
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
TO
<P=001>
(Continued)
■ Preset tuning
■ How to backup the preset tuning stations
You can store up to 30 stations in memory (30
stations consisting of any combination of FM and AM
stations you like) and recall them at the push of a
button. FM stations can be recalled in either stereo
or mono.
When the backup memory battery is installed, the
contents of the preset tuning can be stored even
when the power is turned off.
1
Tune to the desired station.
(Perform steps 1 - 3 in the "Tuning" section on
page 8.)
2
Press the TUNER MEMORY button.
Preset number
3
X W
Within 5 seconds, press the PRESET ( or )
button until the preset number to be programmed
flashes in the display.
4
Within 5 seconds, press the TUNER MEMORY
button to store that station in the selected station
preset number memory.
● If the "MEMORY" and preset number indicators
go out before the station is memorised, repeat
the operation from step 2.
● The preset numbers in step 2 are displayed
starting from the low numbers which have not
been assigned. If the preset numbers are assigned in order, step 3 can also be omitted.
If you want to change the station assigned to a
preset number, select that preset number in step
3.
5
1
2
Insert 3 "AA" size batteries (UM/SUM-3, R6,
HP-7 or similar) into the backup memory battery
compartment.
● When inserting or removing the batteries, push
them towards the battery terminals.
● Installing the batteries incorrectly may cause the
unit to malfunction.
ë
Repeat steps 1 - 4 to set other preset stations,
or to change a preset station.
Notes:
● When the backup memory batteries are installed
in the unit, the memory recalls the last station
received even after setting the ON/STAND-BY
switch to STAND-BY or unplugging the unit from
AC power.
It also stores the sound level.
● If the backup memory batteries are not inserted
and the power is disconnected, the tuner’s preset
memories will be erased.
● Replace the backup memory batteries approximately once a year.
■ To recall a memorised station
1
2
Remove the backup memory battery compartment cover located on the bottom of the unit.
Set the function switch to TUNER.
X W
Press the PRESET ( or ) button to recall the
desired preset channel number.
● If there are no stations memorised, this operation
can not be performed.
■ To clear all memorised stations
1
2
3
Set the function switch to TUNER.
4
Within 5 seconds, press the CLEAR button on
the remote control.
Caution:
● When inserting or replacing the batteries for the
backup memory, connect the AC power lead and
set the ON/STAND-BY switch to ON. This will
extend battery life.
Press the TUNER MEMORY button.
W X
Press the PRESET ( or ) button to select the
channel number you want to erase.
9
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=002>
■ Recording from the built-in radio
RECORDING
● When recording important selections, be sure to
make a preliminary test to ensure that the desired
material is being properly recorded.
● The ALC (Automatic Record Level Control) circuit automatically controls the level of the input
signal used for recording.
● The VOLUME control may be adjusted with no
effect on the recorded signal. (Variable Sound
Monitor)
● Metal and CrO2 tapes cannot be used for recording.
1
Set the function switch to TUNER.
● Tune in to the station to be recorded.
2
Load a blank cassette into the cassette compartment.
3
4
5
Press the PAUSE button.
Press the RECORD button.
Press the PAUSE button again.
To stop recording:
Press the STOP/EJECT button.
■ Erasing a recorded tape
PLAY / PAUSE
TUNING
STOP
TUNING
1
2
Set the function switch to TAPE.
3
Press the RECORD button.
Load the tape to be erased into the cassette
compartment.
MAINTENANCE
■ Internal care
REPEAT
BAND
● Do not touch the Laser pickup lens. If fingerprints
or dust accumulate on the pickup, clean it gently
with a dry cotton swab.
● Dirty heads, capstan or pinch roller can cause
poor sound and tape jams. Clean these parts
with a cotton swab moistened with commercial
head/pinch roller cleaner or isopropyl alcohol.
● After long use, the deck’s heads and capstan
may become magnetised, causing poor sound.
Demagnetise these parts once every 30 hours
of playing/recording by using a commercial tape
head demagnetiser. Read the demagnetiser’s
instructions carefully before use.
ON/STAND-BY
(Function)
■ Recording from the built-in CD player
1
Set the function switch to CD.
● Load the disc to be recorded.
2
Load the cassette into the cassette compartment.
3
4
Press the RECORD button.
Press the PLAY/PAUSE (0 6) button on the CD.
To stop recording:
Press the STOP/EJECT button.
The tape will stop.
Note:
● If the STOP(■) or PLAY/PAUSE (0 6) button
on the CD player is pressed whilst recording, or
if the CD comes to its end, the tape deck will not
stop.
To record a specific track:
Press the UP (2 / 4) or DOWN (3 / 5) button
on the CD player until the desired track number is
displayed, then start recording.
■ External care
● Periodically wipe the cabinet with a soft cloth and
a diluted soap solution, then wipe with a dry
cloth.
● Do not use chemically treated cleaning cloths or
other chemicals.
10
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
<P=003>
SPECIFICATIONS
SHARP reserves the right to make design and specification changes for product improvement without
prior notice.
● General
Power source: AC 230-240 V, 50 Hz
DC 9 V ["D" size (UM/SUM-1, R20
or HP-2) battery × 6]
DC 4.5 V ["AA" size (UM/SUM-3,
R6 or HP-7) battery × 3 for backup
memory]
Power
consumption: 8 W
Output power: RMS; 4.6 W (2.3 W + 2.3 W)
(DC operation, 10 % T.H.D.)
MPO; 8.4 W (4.2 W + 4.2 W)
(AC operation, 10 % T.H.D.)
Speakers:
10 cm (4") full-range speaker x 2
Output
Headphones; 16-50 ohms
terminals:
(recommended; 32 ohms)
Dimensions: Width; 400 mm (15-3/4")
Height; 158 mm (6-1/4")
Depth; 212 mm (8-3/8")
Weight:
2.7 kg (6.0 lbs.) without batteries
● Radio
Frequency
FM; 87.5 - 108 MHz
range:
AM; 522 - 1,620 kHz
● Compact disc player
Type:
Compact disc
Signal
Non-contact, 3-beam semireadout:
conductor laser pickup
Audio
channels:
2
Filter:
8-times oversampling digital filter
D/A converter: 1-bit D/A converter
Wow and
Unmeasurable
flutter:
(less than 0.001% W. peak)
● Tape recorder
Frequency
response:
Signal/noise
ratio:
Wow and
flutter:
Motor:
Bias system:
Erase
system:
50 - 14,000 Hz (Normal tape)
50 dB
0.25 % (WRMS)
DC 9 V electric governor
AC bias
Magnet erase
TERMS OF GUARANTEE
Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replacement, of
this product subject to the conditions listed below:-
1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not
cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with the product,
or repair other than by a Service Facility appointed by Sharp.
2. As this product is intended for private domestic use only, the guarantee will not apply if the product is used
in the course of a business, trade or profession.
3. To benefit from this guarantee, any fault which occurs must be notified to Sharp, or its appointed Service
Facility within one year from the date this product was purchased. Proof of purchase must be provided.
4. The guarantee does not cover carriage costs, jewelled styli, audio tapes, compact discs or batteries.
5. In the unlikely event of this product requiring repair, please contact the supplier from whom it was purchased.
Where this is not possible, please contact the Sharp Customer Information Centre on the telephone number
given below.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional benefit to your statutory rights, and does not affect these rights
in any way.
If you have any difficulty operating this product, or would like information on other Sharp products, please
telephone the Sharp Customer Information Centre on the number given below.
Sharp Customer Information Centre - Telephone 0345 125387
SHARP ELECTRONICS (U.K.) LTD.
Sharp House, Thorp Road, Newton Heath, Manchester, M40 5BE
SHARP CORPORATION
QT-CD250H(SUK) TINSE0043SJZZ
Downloaded From Disc-Player.com Sharp Manuals
9906
A0002.TO
TINSE0043SJZZ