BGR
AX-9
Natural Sound Stereo Integrated Amplifier
Préampli/ampli de puissance stéréo de la série “Natural Sound”
Natural Sound Stereo-Verstärker
Natural Sound Integrerad Stereo Förstärkare
Amplificatore integrato stereo a Suono Naturale
Amplificador integrado estéreo de Sonido Natural
Natural Sound Geïntegreerde Stereo Versterker
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
SUPPLIED ACCESSORIES
ACCESSOIRES FOURNIS
MITGELIEFERTES ZUBEHÖR
MEDFÖLJANDE TILLBEHÖR
ACCESSORI IN DOTAZIONE
ACCESORIOS INCLUIDOS
BIJGELEVERDE ACCESSOIRES
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Remote Control Transmitter
Emetteur de télécommande
Fernbedienung
Fjärrkontroll
Telecomando
Transmisor del control remoto
Afstandbediening
●
●
●
●
●
●
●
YAMAHA HIFI SYSTEM
REMOTE CONTROL TRANSMITTER
AUX
DIR A
DIR B REC/PAUSE
PLAY
A/B
–
PRESET
+
A/B/C/D/E
DISC
PLAY
MD
TAPE
TUNER
CD
PHONO
SLEEP
2
POWER
After unpacking, check that the following parts are contained.
Après le déballage, vérifier que les pièces suivantes sont incluses.
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
Kontrollera efter det apparaten packats upp att följande delar finns med.
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
Desembale el aparato y verificar que los siguientes accesorios están en la caja.
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
VOLUME
Batteries (size AA, R6, UM-3)
Piles (taille AA, R6, UM-3)
Batterien (Größe AA, R6, UM-3)
Batterier (storlek AA, R6, UM-3)
Batterie (dimensioni AA, R6, UM-3)
Pilas (tamaño AA, R6, UM-3)
Batterijen (maat AA, R6, UM-3)
FEATURES
English
Thank you for selecting this YAMAHA stereo amplifier.
● 50W + 50W (8Ω) RMS Output Power, 0.03% THD, 20–20,000 Hz
● High Dynamic Power, Low Impedance Drive Capability
● PURE DIRECT Switch to Reproduce the Purest Source Sound
● Remote Control Capability
CONTENTS
Supplied Accessories .........................................................................................2
Caution ...............................................................................................................4
Notes about the Remote Control Transmitter .....................................................5
Connections .......................................................................................................6
Controls and Their Functions .............................................................................8
Operations .......................................................................................................10
Troubleshooting ................................................................................................13
Specifications ...................................................................................................14
3
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2.
Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
3.
Never open the cabinet. If something drops into the set, contact
your dealer.
4.
Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wires themselves.
5.
The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
6.
Always set the VOLUME control to “0” before starting the audio
source play: increase the volume gradually to an appropriate level
after the play has been started.
7.
Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
8.
Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
9.
When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wire in the mains lead are coloured in accordance with
the following code:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug. Proceed as follows: the wire
which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off.
In this state, this unit is designed to consume a very small
quantity of power.
10. To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
11. Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12. AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
13. Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
IMPEDANCE SELECTOR
IMPEDANCE SELECTOR
SET BEFORE POWER ON
IMPORTANT
Please record the serial number of this unit in the space below.
A OR B:4ΩMIN./SPEAKER
A + B:8ΩMIN./SPEAKER
A OR B:8ΩMIN./SPEAKER
A + B:l6ΩMIN./SPEAKER
A
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
VOLTAGE SELECTOR
SWITCHED
AC OUTLETS
l00W MAX. TOTAL
B
L
+
SPEAKERS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
4
(General model)
Battery installation
Remote control transmitter operation range
2
English
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Remote control
sensor
1
Within approximately
6 m (19.7 feet)
3
30°
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
● Use only AA, R6, UM-3 batteries for replacement.
● Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
● Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
● If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
30°
Notes
● There should be no large obstacles between the remote
control transmitter and the main unit.
● If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
5
CONNECTIONS
Never plug in this unit and other components until all connections are completed.
●
●
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making
sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
Speakers A
Right
GND
OUTPUT
LINE OUT
CD player
LINE OUT
Turntable
Tuner
Left
2
*
(General model)
GND
IMPEDANCE SELECTOR
SET BEFORE POWER ON
VOLTAGE SELECTOR
L
R
PHONO
A OR B:4ΩMIN./SPEAKER
A + B:8ΩMIN./SPEAKER
A OR B:8ΩMIN./SPEAKER
A + B:l6ΩMIN./SPEAKER
1
L
R
2
CD
A
AUX
SWITCHED
AC OUTLETS
l00W MAX. TOTAL
TUNER
3 or 5
3
TAPE PB
PLAY
4 or 6
4
RECOUT
REC
L
R
TAPE
B
L
R
AUDIO SIGNAL
+
L
R
MD
+
SPEAKERS
To AC outlet
1
Tape deck, etc.
MD recorder, etc.
AUDIO OUT
LINE IN
LINE OUT
LINE IN
LINE OUT
*
Right
Left
Video cassette player,
LD player, etc.
Speakers B
1
2
**
,
6
: Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 7.
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
●
●
●
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
Use speakers with the specified impedance shown on the
rear of this unit.
<General model only>
Banana Plug connections are also possible. Simply insert
the Banana Plug connector into the corresponding terminal.
English
CONNECTING SPEAKERS
How to Connect:
Red: positive (+)
Black: negative (–)
2
➀ Unscrew the knob.
➁ Insert the bare wire.
1
3
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂ Tighten the knob and
secure the wire.
IMPEDANCE SELECTOR switch
Be sure to switch this only when the power to this unit is not
on.
Select the position whose requirements your speaker system
meets.
(General model)
IMPEDANCE SELECTOR
SET BEFORE POWER ON
A OR B:4ΩMIN./SPEAKER
A + B:8ΩMIN./SPEAKER
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
A OR B:8ΩMIN./SPEAKER
A + B:l6ΩMIN./SPEAKER
(Left position)
If you use one pair of speakers, the impedance of each
speaker must be 4Ω or higher.
If you use two pairs of speakers, the impedance of each
speaker must be 8Ω or higher.
(Right position)
If you use one pair of speakers, the impedance of each
speaker must be 8Ω or higher.
If you use two pairs of speakers, the impedance of each
speaker must be 16Ω or higher.
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S) (SWITCHED)
*
1
(Europe and General models)
.......................................................... 3 SWITCHED OUTLETS
(U.K. model) ........................................ 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
STANDBY/ON switch or the provided remote control
transmitter’s POWER key. These outlets will supply power to
any component whenever this unit is turned on.
The maximum power (total power consumption of components)
that can be connected to the SWITCHED AC OUTLET(S) is
100 watts.
2
GND terminal (For turntable use)
*
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
7
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
1 2 3 45 6
7
8
INPUT
l
NATURAL SOUND STEREO AMPLIFIER AX 9
VOLUME
STANDBY/ON
PURE
TAPE
DIRECT MONITOR
AUX
TAPE
MD
CD
TUNER
PHONO
SLEEP
0
PHONES
9 0
SPEAKERS
A
B
ON
ON
OFF
OFF
A
PURE
DIRECT
B C
2 STANDBY/ON switch
Press this switch to turn the power to this unit on. Press it
again to turn this unit into the standby mode.
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control
transmitter.
3 Remote control sensor
Receives signals from the remote control transmitter.
4 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
5 PURE DIRECT indicator
Lights up while the PURE DIRECT switch is on.
6 TAPE MONITOR indicator
Lights up while the TAPE MONITOR switch is on.
* When the tape deck (TAPE) is selected as the input source,
this indicator will not light up even if the TAPE MONITOR
switch is on.
8 VOLUME control
Used to raise or lower the volume level.
9 Control door
See page 12 for how to open and close the control door.
BASS
TREBLE
0
0
–
1 Power indicator
Lights up while the power to this unit is on.
7 INPUT selector and indicators
When turned, selects a program source to listen to.
The indicator for the currently selected source lights up.
TAPE
MONITOR
+
–
+
D
l0
BALANCE
L
R
E
0 PHONES jack
PHONES
When you listen with headphones,
connect the headphones to the
PHONES jack.
When listening with headphones
privately, set both the SPEAKERS
A and B switches to the OFF
position.
A SPEAKERS switches
Set the switch A or B (or both A and B) for the speaker system
(connected to this unit) you will use to the ON position. Set the
switch for the speaker system you will not use to the OFF
position.
B PURE DIRECT switch
You can enjoy the purest possible sound from your audio
sources by pressing this switch so that the PURE DIRECT
indicator lights up. By doing so, the audio signal bypasses the
BASS, TREBLE and BALANCE controls, eliminating any
alterations to the audio signal.
C TAPE MONITOR switch
When the tape deck connected to the TAPE terminals on the
rear of this unit is used for recording, you can monitor the
sounds being recorded by pressing TAPE MONITOR so that
TAPE MONITOR indicator lights up.
D Tone controls
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
E BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
8
English
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the
CD player, tuner or tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control transmitter will also control various functions of each component.
For Control of This Unit
1 SLEEP timer key
This unit is automatically turned into the standby mode one
hour after this key is pressed (so that SLEEP indicator lights
up).
YAMAHA HIFI SYSTEM
REMOTE CONTROL TRANSMITTER
2 POWER key
Turns the power to this unit on and turns this unit into the
standby mode alternately.
AUX
DIR A
DIR B REC/PAUSE
1
2
PLAY
A/B
–
PRESET
+
A/B/C/D/E
DISC
PLAY
3
1
2
MD
3 Input selector keys
Selects input source.
TAPE
TUNER
3
CD
4 VOLUME +/– keys
Turns the volume level up/down.
PHONO
SLEEP
POWER
For Other Component Control
VOLUME
4
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the
corresponding instruction on your component’s manual.
1 Tape deck keys
Controls tape deck.
* DIR A, B and A/B are applicable only to double
cassette tape deck.
* For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
tape running.
2 Tuner keys
Controls tuner.
+: Selects higher preset station number.
–: Selects lower preset station number.
A/B/C/D/E: Selects the group (A – E) of preset station
numbers.
3 CD player keys
Controls compact disc player.
* DISC is applicable only to compact disc changer.
9
OPERATIONS
TO PLAY A SOURCE
2
3
1, 6
INPUT
l
NATURAL SOUND STEREO AMPLIFIER AX 9
VOLUME
STANDBY/ON
PURE
TAPE
DIRECT MONITOR
AUX
TAPE
MD
CD
TUNER
PHONO
SLEEP
0
PHONES
SPEAKERS
A
B
ON
ON
OFF
OFF
4
1
PURE
DIRECT
TAPE
MONITOR
BASS
TREBLE
0
0
–
7
–
+
L
R
7
4
VOLUME
+
l0
BALANCE
Select the speakers to be used.
SPEAKERS
A
B
0
l0
ON
ON
OFF
OFF
Set to the “0” position.
2
* If you use two speaker systems, press both the A and B
switches.
Turn the power on.
STANDBY/ON
5
6
Play the source.
VOLUME
Lights up.
3
Select a desired input source.
INPUT
0
l0
Adjust to the desired output level.
AUX
TAPE
MD
CD
TUNER
PHONO
7
The indicator of the selected source lights up.
If desired, adjust the BASS, TREBLE and BALANCE
controls or turn on the PURE DIRECT switch. (Refer to
page 12.)
When you finish using this unit
Press the STANDBY/ON switch again to turn this unit into the
standby mode.
10
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control
transmitter.
l
NATURAL SOUND STEREO AMPLIFIER AX 9
1
2
INPUT
VOLUME
English
TO RECORD A SOURCE TO TAPE (OR MD)
STANDBY/ON
PURE
TAPE
DIRECT MONITOR
AUX
TAPE
MD
CD
TUNER
PHONO
SLEEP
0
PHONES
SPEAKERS
A
B
ON
ON
OFF
OFF
PURE
DIRECT
TAPE
MONITOR
BASS
TREBLE
0
0
–
+
–
+
l0
BALANCE
L
R
4
1
3
Select the source to be recorded.
Begin recording on the tape deck (or MD recorder etc.)
connected to this unit.
INPUT
4
AUX
2
TAPE
MD
CD
TUNER
PHONO
If the tape deck connected to the TAPE terminals on the
rear of this unit is used for recording, you can monitor
the sounds being recorded by pressing TAPE
MONITOR so that TAPE MONITOR indicator lights up.
TAPE
MONITOR
TAPE
MONITOR
Play the source and then turn the VOLUME control up
to confirm the input source.
Lights up.
VOLUME
0
l0
Notes
The settings of the VOLUME, BASS, TREBLE, BALANCE
controls and PURE DIRECT switch have no effect on the
material being recorded.
When you listen with headphones
Connect the headphones to the PHONES jack. When listening
with headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
PHONES
11
Adjusting the BALANCE control
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Selecting the SPEAKER system
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
SPEAKERS
BALANCE
L
R
Adjusting the BASS and TREBLE
controls
BASS
TREBLE
0
0
–
BASS
+
–
PURE
DIRECT
PURE
DIRECT
Lights up.
When it is not necessary to operate controls inside the control
door, close the door.
12
OFF
You can enjoy the purest possible sound from your audio
sources by pressing this switch so that the PURE DIRECT
indicator lights up. By doing so, the audio signal bypasses the
BASS, TREBLE and BALANCE controls, eliminating any
alterations to the audio signal.
Open/close the control door
To close the door
2
OFF
Using the PURE DIRECT switch
TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency
response.
1
B
ON
+
: Turn this clockwise to increase (or counterclockwise to decrease) the low frequency
response.
To open the door
A
ON
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
CAUSE
REMEDY
The unit fails to turn on when the
STANDBY/ON switch is pressed, or turns
into the standby mode suddenly soon after
the power is turned on.
Power cord is not plugged in or is not
completely inserted.
Firmly plug in the power cord.
The IMPEDANCE SELECTOR switch on the
rear panel is not set to either end closely.
Set the switch to either end closely.
It happens that this unit does not work
normally.
There is an influence of strong external noise
(lightning, excessive static electricity, etc.) or a
misoperation on this unit while using this unit.
Turn this unit into the standby mode and
disconnect the AC power cord from the AC
outlet. After about 30 seconds have passed,
connect the power and operate this unit again.
No sound.
Incorrect output cord connections.
Connect the cords properly. If the problem
persists, the cords may be defective.
Appropriate input source is not selected.
Select an appropriate input source with the
INPUT selector.
The SPEAKERS switches are not set properly.
Set the SPEAKERS switch which corresponds
to the speakers to be used to the ON position.
Speaker connections are not secure.
Secure the connections.
The protection circuit has been activated
because of short circuit etc.
Turning the unit into the standby mode and
then on will reset the protection circuit.
The SLEEP timer has functioned.
Cancel the SLEEP timer function.
Incorrect setting of the BALANCE control.
Adjust it to the appropriate position.
Incorrect cord connections.
Connect the cords properly. If the problem
persists, the cords may be defective.
There is a lack of bass, and no ambience.
The + and – wires are connected in reverse at
the amplifier or speakers.
Connect the speaker wires in the correct phase
(+ and –).
Sound “hums”.
Incorrect cord connections.
Firmly connect the audio plugs. If the problem
persists, the cords may be defective.
No connection from the turntable to the GND
terminal.
Make the GND connection between the
turntable and this unit.
The volume level is low while playing a
record.
The record is being played on a turntable with
an MC cartridge.
The player should be connected to the unit
through the MC head amplifier.
The volume level cannot be increased, or
sound is distorted.
The component connected to the REC OUT
terminals of this unit is in the standby mode.
Turn the power to the component on.
The sound is degraded when listening with
the headphones connected to the compact
disc player or cassette deck that are
connected with this unit.
This unit is in the standby mode.
Turn the power to this unit on.
Using the BASS, TREBLE and BALANCE
controls does not affect the tone.
The PURE DIRECT switch is ON.
The PURE DIRECT switch must be switched
OFF to use those controls.
The remote control transmitter does not
work.
Direct sunlight or lighting (of an inverter type of
fluorescent lamp etc.) is striking the remote
control sensor of the main unit.
Change position of the main unit.
The distance or range within which the
remote control transmitter can be used is
short.
The batteries of this remote control transmitter
are too weak.
Replace the batteries with new ones.
The sound suddenly goes off.
Only one side speaker outputs the sound.
English
TROUBLESHOOTING
13
SPECIFICATIONS
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.03% THD .......................50W+50W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring method)
8/6/4/2 ohms.................................................78/88/100/112W
Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT ...........................................0.02%
CD/TUNER/TAPE/MD/AUX to SP OUT (25W/8 ohms)..0.02%
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted) ............................... 82 dB
CD/TUNER/TAPE/MD/AUX (150 mV Input Shorted) ... 105 dB
DIN Standard Output Power per Channel
(4 ohms, 1 kHz, 0.7% THD)
[U.K. and Europe models only] .......................................65W
Residual Noise (IHF-A Network)..................................... 100 µV
IEC Power (8 ohms, 1 kHz, 0.03% THD)
[U.K. and Europe models only] .......................................65W
Channel Separation (Vol. –30 dB)
PHONO MM (Input 0 ohm Terminated 1 kHz) ..............60 dB
CD/TUNER/TAPE/MD/AUX (Input 5.1 k-ohms Terminated
1 kHz) ............................................................................60 dB
Power Band Width
8 ohms, 25W, 0.06% THD............................10 Hz to 40 kHz
Maximum Output Power (8 ohms, 1 kHz, 10% THD)
[General model only].......................................................70W
Tone Control Characteristics
BASS:
Boost/cut..................................................±10 dB (50 Hz)
Turnover Frequency .............................................350 Hz
TREBLE:
Boost/cut ................................................±10 dB (20 kHz)
Turnover Frequency ............................................3.5 kHz
Input Sensitivity/Impedance
PHONO MM..............................................2.5 mV/47 k-ohms
CD/TUNER/TAPE/MD/AUX.......................150 mV/47 k-ohms
Power Supply
[U.K. and Europe models].............................AC 230V, 50 Hz
[General model] ..................AC 110/120/220/240V, 50/60 Hz
Maximum Input Signal (1 kHz, 0.04% THD)
PHONO MM .................................................................90 mV
Power Consumption...........................................................120W
Damping Factor
8 ohms, 20 Hz–20 kHz .........................................80 or more
Output Level/Impedance
REC OUT ..................................................150 mV/800 ohms
Headphone Jack Rated Output/ Impedance
Output Level (8 ohms, 1 kHz, 0.03% THD) .....................0.4V
Impedance ..............................................................390 ohms
AC Outlets
3 SWITCHED OUTLETS
[Europe and General models]................100W max. total
1 SWITCHED OUTLET
[U.K. model] ...........................................100W max. total
Dimensions (W x H x D) .......................280 x 118.5 x 388.5 mm
........................................................(11” x 4-11/16” x 15-5/16”)
Frequency Response (20 Hz to 20 kHz)
CD/TUNER/TAPE/MD/AUX ......................................0±0.5 dB
Weight.........................................................6.1 kg (13 lbs. 7 oz.)
RIAA Equalization Deviation (20 Hz to 20 kHz)
PHONO MM ............................................................0±0.5 dB
Accessories.......................................Remote control transmitter
....................................................................................Batteries
Specifications subject to change without notice.
14
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VZ21860