advertisement
AZ 1145 29/11/00 18:22 Page 1
CD Radio Cassette Recorder
AZ 1145
AZ 1146
AZ 1147
AZ 1148
BATT
LOW
TAPE
OFF
DYNAMIC
BOOST
PLAY•P
AUSE
CD
PROGRAM
REPEAT
ALL
DIGIT
AL TUNER
1 2
3
D igital
R emote
C ontr
ST ST
OP
Downloaded From DvDPlayer-Manual.com Philips Manuals
XP AZ1145/00-1 08-05-2000 15:42 Pagina 2
AZ 1145 /00 page
2
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved moulded
13 Amp plug. To change a fuse in this type of plug proceed as follows:
• Remove fuse cover and fuse.
• Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
• Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp.
Note: The severed plug must be disposed to avoid a possible shock hazard should it be inserted into a
13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:
• Connect the blue wire to the terminal marked N or coloured black.
• Connect the brown wire to the terminal marked L or coloured red.
• Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.Copyright in the U.K.:
Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s
Protection Acts 1958 to 1972.
n Norge
Advarsel: For å redusere faren for brann eller elektrisk støt; skal apparatet ikke utsettes for regn eller fuktighet.
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten
English
Français
Español
Deutsch
........................................... 4
...................................... 14
....................................... 24
....................................... 34
Nederlands
Italiano
........................................ 54
Português
Dansk
............................................ 74
Svenska
.............................. 44
.................................. 64
...................................... 84
i Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio AZ 1145 Philips risponde alle prescrizioni dell’art. 2 comma 1 del D. M. 28 Agosto
1995 n. 548.
Suomi
............................................ 94
Philips Consumer Electronics
Philips, Glaslaan 2,
Έλληνικά
Downloaded From DvDPlayer-Manual.com Philips Manuals
2
5616 JB Eindhoven, The Netherlands
..................... 104
2
XP AZ1145/00-1 08-05-2000 15:42 Pagina 3
1
2
3 4
5
(
6 7 5 8 9 0
AZ 1145/00 page
3
*
TAPE
OFF
CD
TUNER
BATT
LOW
VOL
DBB
DYNAMIC
BOOST
PAUSE
STOP
•OPEN
PLAY•PA
USE
CD
PROGRAM
SEAR
CH
CD MO
DE
STOP
PLAY
SEARCH
REMOTE
SENSOR
PROGRAM
CD RAD
AZ1145
IO CAS
SETTE R
ECORD
ER
DIGIT
AL T
AMIC BA
UNER
SS BO
OST
1
2
3
PR
ES
ET
BA
ND
!
@ # $ % ^ &
(
)
¡
™
2
4
6
9
PRESE
T
VOLU
ME
TUNIN
G
SHU
FFLE
STOP
SEARCH
Digit al Re mote
Cont rol
1
3
5
7
8
Downloaded From DvDPlayer-Manual.com Philips Manuals
3
XP AZ1145/00-1 08-05-2000 15:42 Pagina 4
AZ 1145 /00 page
4
CONTROLS
TOP AND FRONT PANELS
1 POWER slider - selects the sound source for CD/ TUNER/ TAPE
OFF and also switches the set off
2 VOL +, – - adjusts the volume level
3 BATT LOW - indicates when battery power is running low
4 DBB (Dynamic Bass Boost) - enhances the bass
5 OPEN•CLOSE - opens/ closes the CD door
6 CASSETTE RECORDER keys
RECORD
0 - starts recording
PLAY
1 - starts playback
SEARCH
5
/
6 - fast winds/rewinds the tape
STOP•OPEN
9/ - stops the tape;
- opens the cassette compartment
PAUSE
; - interrupts recording or playback
7 REMOTE SENSOR - infrared sensor for the remote control
8 1-3 - programmes and selects your favourite three radio stations
9 PRESET
3, 4 - (down, up) selects preset tuner stations
0 BAND - selects waveband
! PLAY PAUSE
2; - starts /pauses
CD playback
@ CD MODE - selects a different play mode e.g. SHUFFLE/ REPEAT CD tracks or programme in random
/repeated order
# STOP
9 - stops CD playback or erase a CD programme; activates/ deactivates display demo mode.
$ Cassette door
% Display - shows the status of the set
^ SEARCH
∞
/
§
Tuner: (down, up) tunes radio stations.
CD: - searches back and forward within a track;
- skips to the beginning of a current track/ previous/ later track
& PROGRAM -
Tuner - programmes preset radio stations;
CD - programmes tracks and reviews the programme
BACK PANEL
* p - 3.5 mm stereo headphone socket
( Telescopic antenna - improves FM reception
) BEAT CUT switch - eliminates possible whistle tones during
MW/LW recordings
¡ AC MAINS - inlet for power cord
™ Battery compartment - for six batteries, type R-14, UM-2 or C-cells
REMOTE CONTROL
1 VOLUME
3,4 – adjusts volume level
2 PRESET
3,4 (up, down) – selects a preset radio station
3 TUNING
∞, § (down, up) – tunes to radio stations
4 SHUFFLE – to play CD tracks in random order
5 REPEAT – repeats a track/ CD programme/ entire CD
6
2; – starts and pauses CD playback/ interrupts CD playback
7
¡, ™ – skips to the beginning of a current track/ previous/ later track
8 STOP
9 – stops CD playback or erases a
CD programme
9 SEARCH
5, 6 – searches backwards or forwards within a track/CD
CAUTION
Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
Downloaded From DvDPlayer-Manual.com Philips Manuals
4
XP AZ1145/00-1 08-05-2000 15:42 Pagina 5
Whenever convenient, use the mains supply if you want to conserve battery life. Make sure you remove the plug from the set and wall socket before inserting batteries.
BATTERIES (OPTIONAL)
1. Open the battery compartment and insert six batteries, type
R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "
+
" and "
-
" symbols inside the compartment.
Remote control (supplied)
Open the battery compartment and insert two batteries, type AAA, R03 or UM4 (preferably alkaline).
2. Replace the compartment door, making sure the batteries are firmly and correctly in place. The set is now ready to operate.
– If BATT LOW lights up, battery power is running low.
– The BATT LOW indicator eventually goes out if the batteries are too weak.
Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst.
Therefore:
• Do not mix battery types: e.g. alkaline with carbon zinc.
Only use batteries of the same type for the set.
• When inserting new batteries, do not try to mix old batteries with the new ones.
• Remove the batteries if the set is not to be used for a long time.
• Batteries contain chemical substances, so they should
be disposed of properly.
For users in the U.K.: please follow the instructions on page 2.
Using AC MAINS
1. Check if the mains voltage as shown on the type plate on
the base of the set, corresponds to your local mains supply.
If it does not, consult your dealer or service centre.
2. If your set is equipped with a voltage selector, adjust the selector so that it matches with the local mains supply.
3. Connect the mains lead to the wall socket and the set is now ready for use.
4. To disconnect the set from the mains supply completely, remove the plug from the wall socket.
AZ 1145/00 page
5
POWER SUPPLY
6 x R14 • UM-2 • C-CELLS
AC ~ MAINS
Downloaded From DvDPlayer-Manual.com Philips Manuals
5
XP AZ1145/00-1 08-05-2000 15:42 Pagina 6
AZ 1145 /00 page
6
BASIC FUNCTIONS GENERAL INFORMATION
Switching on and off
• Adjust the POWER slider to the desired sound source: CD,
TUNER or TAPE/
OFF
.
• The set is switched off when the POWER slider is in the
TAPE/
OFF
position and the keys on the tape deck are released.
™ The volume and tuner presets will be retained in the set's memory.
Adjusting volume and sound
1. Press the VOL +, – controls to increase or decrease volume
(or press
3 or 4 on the remote control).
2. Adjust the DBB control to select dynamic bass boost on or off.
TAPE
OFF
CD
TUNER
BATT
LOW
VOL
DBB
DYNAMIC
BASS
BOOST
PAUS
E
STOP
•OPE N
PLAY•PA
USE
CD
PROGRAM
REPEAT
ALL
SEARC
H
TAPE
OFF
CD
TUNER
BATT
LOW
VOL
DBB
DYNAMIC
BASS
BOOST
PAUS
E
STOP•O
PEN
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
PLAY
RECOR
D
REMOTE
SENSOR
CD
PROGRAM
REPEAT
ALL
PHILIPS demo mode
1. On the set, press the CD STOP
9 button for 5 seconds.
™ PH..IL ..IPS scrolls across the display continuously.
2. To return to the current display you can either:
• press any function button on the front panel. This interrupts the demo mode for 30 seconds;
• press the CD STOP
9 button for 5 seconds. PH..IL ..IPS scrolls once before the demo mode is cancelled.
GENERAL INFORMATION
General maintenance
• Do not expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight.
• To clean the set, use a soft, slightly dampened chamois leather.
Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing.
Safety information
• Place the set on a hard and flat surface so that the system does not tilt. Make sure there is adequate ventilation to prevent the system from overheating.
• The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated.
DYNAMIC
BASS
BOOST
PLAY•PA
USE
PAUSE
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
Downloaded From DvDPlayer-Manual.com Philips Manuals
6
XP AZ1145/00-1 08-05-2000 15:42 Pagina 7
AZ 1145/00 page
7
DIGITAL TUNER
TUNING TO RADIO STATIONS
1. Select TUNER source.
™ is displayed briefly and then the radio station frequency is shown.
2. Press BAND once or more to select your waveband.
3. Press
∞ or § on the set or on the remote control and release when the frequency in the display starts running.
™ The tuner automatically tunes to a station of sufficient reception. Display shows during automatic tuning.
™ If a FM station is received in stereo,
STEREO
is shown.
4. Repeat step 3 if necessary until you find the desired station.
• To tune to a weak station, press
∞ or § briefly and repeatedly until you have found optimal reception.
5. Adjust the power slider to TAPE/
OFF
position to switch off the set.
To improve radio reception
– For FM, pull out the telescopic aerial. Incline and turn the aerial. Reduce its length if the signal is too strong (very close to a transmitter).
– For MW/LW, the set is provided with a built-in aerial so the telescopic aerial is not needed. Direct the aerial by turning the whole set.
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
PLAY
RECOR
D
SEARCH
REMOTE
SENSOR
PROGRAM
Favourite station selection
For your favourite 3 tuner stations, you can use the easy one-touch programming and selection 1, 2 or 3 buttons.
1. Tune to your desired station (see Tuning to radio stations).
2. To store your station, press 1, 2 or 3 for 2 seconds or more.
™ Display: shows
PROGRAM
briefly, your favourite preset station number and the tuner frequency.
OPEN
CD
OGRAM
EPEAT
ALL
SEARC
H
Programming radio stations
You can store up to a total of 30 radio stations in the memory.
1. Tune to your desired station (see Tuning to radio stations).
2. Press PROGRAM to activate programming.
– Display:
PROGRAM
flashes.
3. Press PRESET
4 or 3 once or more to allocate a number from
1 to 30 to this station.
4. Press PROGRAM again to confirm the setting.
– Display:
PROGRAM
disappears, the preset number and the frequency of the preset station are shown.
5. Repeat the above four steps to store other stations.
– You can overwrite a preset station by storing another frequency in its place.
Tuning to preset stations
Press 1, 2, 3 or PRESET
4 or 3 until the desired preset station is displayed.
Downloaded From DvDPlayer-Manual.com Philips Manuals
SEARC
H
PLAY
RECOR
D
SEARCH
SEARCH
REMOTE
SENSOR
PROGRAM
PLAY
RECOR
D
REMOTE
SENSOR
PROGRAM
1 2
3
PRESET
BA
ND
FM
TUNER
STEREO
1
2
3
PRESET
BA
ND
1
2
3
PRESET
BA
ND
7
XP AZ1145/00-1 08-05-2000 15:42 Pagina 8
AZ 1145 /00 page
8
CD PLAYER
Playing a CD
1. Select CD source.
™ is displayed briefly.
2. Lift the CD door open.
™ Display: when you open the CD door.
3. Insert a CD or CD-R(W) with the printed side facing up and close the CD door.
™ Display: d1SC flashes as the CD player scans the contents of a CD. The total number of tracks and playing time are then shown.
Display: is shown if the CD-R(W) is blank or not finalised.
4. Press PLAY•PAUSE
2; (on the remote control 2;) to start playback.
™ Display: Current track number and elapsed playing time of the track during CD playback.
5. To pause playback press PLAY•PAUSE
2;.
Press PLAY•PAUSE
2; again to resume play.
™ The display freezes and the elapsed playing time flashes when playback is paused.
6. To stop CD playback, press STOP
9.
Note: CD play will also stop when:
– the CD door is opened;
– the CD has reached the end
(unless you have selected REPEAT or REPEAT ALL);
– you select another source: TAPE / TUNER.
Selecting a different track
• Press SEARCH
∞ or § (on the remote control ¡ or ™) once or repeatedly until the desired track number appears in the display.
• If you have selected a track number shortly after loading a CD or in the PAUSE position, you will need to press
PLAY•PAUSE
2; to start playback.
Finding a passage within a track
1. Press and hold down SEARCH
∞ or § (on the remote control
5 or 6).
™ The CD is played at high speed and low volume.
2. When you recognize the passage you want, release SEARCH
∞ or §.
– Normal playback continues.
Note: During a CD programme or if SHUFFLE/ REPEAT active,
searching is only possible within a track.
TAPE
OFF
CD
TUNER
BATT
LOW
VOL
DBB
DYNAMIC
BASS
BOOST
PAUSE
STOP•O
PEN
PLAY•PA
USE
CD
PROGRAM
REPEAT
ALL
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
1
DYNAMIC
BASS
BOOST
PLAY•PA
USE
PAUSE
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
1
PLAY•PA
USE
PAUSE
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
1
PLAY•PA
USE
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
CD RAD
AZ114
5
SETTE R
E
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
Downloaded From DvDPlayer-Manual.com Philips Manuals
8
XP AZ1145/00-1 08-05-2000 15:42 Pagina 9
AZ 1145/00 page
9
CD PLAYER
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes before or during playback. The play modes can also be combined with PROGRAM.
SHUFFLE - tracks of the entire CD/ programme are played in random order
SHUFFLE and REPEAT ALL - to repeat the entire CD/ programme continuously in random order
REPEAT ALL - to repeat the entire CD/ programme
REPEAT - to play the current track continuously
1. To select your play mode, press the CD MODE key (or
SHUFFLE or REPEAT on the remote control) before or during playback until the display shows the desired function.
2. Press PLAY•PAUSE
2; (on the remote control 2;) to start playback if in the STOP position.
3. To return to normal playback, press the CD MODE key or the respective SHUFFLE or REPEAT key until the various SHUFFLE
/ REPEAT modes are no longer displayed.
– You can also press STOP
9 to cancel your play mode.
Programming track numbers
Programme in the STOP position to select and store your CD tracks in the desired sequence. If you like, store any track more than once. Up to 20 tracks can be stored in the memory.
1. Use the SEARCH
∞ or § on the set (on the remote control
¡ or ™) to select your desired track number.
2. Press PROGRAM.
™ Display:
PROGRAM
and the selected track number. appears briefly.
™ If you attempt to programme without first selecting a track
3. Repeat steps 1-2 to select and store all desired tracks.
™ is displayed if you attempt to programme more than
20 tracks.
4. To start playback of your CD programme, press
PLAY•PAUSE
2;.
Reviewing the programme
In the STOP position, press and hold down PROGRAM for a while until the display shows all your stored track numbers in sequence.
CD
PROGRAM
DYNAMIC
BASS
BOOST
PLAY•PA
USE
PAUSE
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
CD MO
DE
PLAY•PA
USE
STOP
STOP•O
PEN
SEARCH
CD
PROGRAM
REPEAT
ALL
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
D
AZ114
Downloaded From DvDPlayer-Manual.com Philips Manuals
9
XP AZ1145/00-1 08-05-2000 15:42 Pagina 10
AZ 1145 /00 page
10
CD PLAYER CASSETTE RECORDER
Erasing a programme
You can erase the programme by:
– pressing STOP
9 once in the STOP position or twice during playback. The display shows ' ' briefly.
– pressing the CD door open;
– switching to TUNER/TAPE source.
CD player and CD handling
• If the CD player cannot read CDs correctly, use a commonly available cleaning CD to clean the lens before taking the set to repair. Other cleaning methods may destroy the lens.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature can cause condensation to cloud over on the lens of your CD player.
Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates.
• Always keep the CD compartment closed to avoid dust on the lens.
• To take a CD out of its box, press the centre spindle while lifting the CD. Always pick up the CD by the edge and return the CD to its box after use to avoid scratching and dust.
• To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc.
• Never write on a CD or attach any stickers to it.
DYNAMIC
BASS
BOOST
PLAY•PA
USE
PAUSE
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
SEARCH
X
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
1
PLAYING A CASSETTE
1. Select TAPE source.
™ The display shows tAPE throughout tape operation.
2. Press STOP•OPEN
9/ to open the cassette door.
3. Insert a recorded cassette and close the cassette door.
4. Press PLAY
1 to start playback.
5. To interrupt playback, press PAUSE
;. To resume, press the key again.
6. By pressing SEARCH
5 or 6 on the set,fast winding of the tape is possible in both directions.
7. To stop the tape, press STOP•OPEN
9/.
– The keys are automatically released at the end of the tape
and the tAPE indication goes out, except if PAUSE
; has
been activated.
CD
TUNER
TAPE
OFF
VOL
DBB
DYNAMIC
BASS
BOOST
PAUSE
STOP•O
PEN
PLAY•PA
USE
CD
PROGRAM
REPEAT
ALL
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
1
Downloaded From DvDPlayer-Manual.com Philips Manuals
10
XP AZ1145/00-1 08-05-2000 15:42 Pagina 11
AZ 1145/00 page
11
RECORDING
GENERAL INFORMATION ON RECORDING
• Recording is permissible insofar as copyright or other rights of third parties are not infringed.
• This deck is not suitable for recording on CHROME (IEC II) or
METAL (IEC IV) type cassettes. For recording, use NORMAL type cassettes (IEC I) on which the tabs have not been broken.
• The best recording level is set automatically. Altering the VOL and DBB controls will not affect the recording in progress.
• At the very beginning and end of the tape, no recording will take place during the 7 seconds, when the leader tape passes the recorder heads.
• To protect a tape from accidental erasure, have the tape in front of you and break out the left tab.
Recording on this side is no longer possible. To record over this side again, cover the tabs with a piece of adhesive tape.
SYNCHRO START CD RECORDING
1. Select CD source.
2. Insert a CD and if desired, programme track numbers.
3. Press STOP•OPEN
9/ to open the cassette door.
4. Insert a suitable cassette into the cassette deck and close the cassette door.
5. Press RECORD
0 to start recording.
– Playing of the CD programme starts automatically from the beginning of the programme. It is not necessary to start the CD
player separately.
To select and record a particular passage within a track
• Press and hold down SEARCH
∞ or § (or on the remote control
5 or 6).
• When you recognize the passage you want, release
SEARCH
∞ or § (or on the remote control 5 or 6).
• To pause CD playback press PLAY/PAUSE
2;.
• Recording will begin from this exact point in the track when you press RECORD
0.
6. For brief interruptions during recording press PAUSE
;. To resume recording, press PAUSE
; again.
7. To stop recording, press STOP•OPEN
9/.
TAPE
OFF
CD
TUNER
BATT
LOW
VOL
DBB
DYNAMIC
BASS
BOOST
PAUSE
STOP•O
PEN
PLAY•PA
USE
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
SEARC
H
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
DYNAMIC
BASS
BOOST
PLAY•PA
USE
PAUS
E
STOP•O
PEN
CD
PROGRAM
REPEAT
ALL
CD MO
DE
STOP
SEARCH
PLAY
RECOR
D
REMOTE
SENSOR
SEARCH
PROGRAM
1
2
Downloaded From DvDPlayer-Manual.com Philips Manuals
11
XP AZ1145/00-1 08-05-2000 15:42 Pagina 12
AZ 1145 /00 page
12
RECORDING
Recording from the radio
1. Tune to the desired radio station (See TUNING TO RADIO
STATIONS).
2. Press STOP•OPEN
9/ to open the cassette door.
3. Insert a suitable cassette into the cassette deck and close the cassette door.
4. Press RECORD
0 to start recording.
• If you are recording from MW/LW stations, adjust the
BEAT CUT switch to eliminate possible whistle tones during recording.
5. For brief interruptions, press PAUSE
;. To resume recording, press PAUSE
; again.
6. To stop recording, press STOP•OPEN
9/.
MAINTENANCE
Tape deck maintenance
To ensure quality recording and playback of the tape deck, clean parts A,B and C shown in the diagram below, after approx.
50 hours of operation, or on average once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck.
1. Open the cassette door by pressing STOP•OPEN
9/.
2. Press PLAY
1 and clean the rubber pressure rollers C.
3. Press PAUSE
; and clean the magnetic heads A and also the capstan B .
4. After cleaning, press STOP•OPEN
9/.
Note: Cleaning of the heads can also be done by playing a cleaning cassette through once.
MAINTENANCE
TAPE
OFF
CD
TUNER
BATT
LOW
VOL
DBB
DYNAMIC
BASS
BOOST
PAUSE
STOP•O
PEN
SEAR CH
CD
PROGRAM
REPEAT
ALL
PLAY
RECOR
D
REMOTE
SENSOR
CD MO
DE
1
C B A A
Environmental information
All unnecessary packaging material has been omitted. We have done our utmost to make the packaging easy to separate into three mono-materials: cardboard (box), expandable polystyrene
(buffer), polyethylene (bags, protective foam).
Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, exhausted batteries and old equipment.
Downloaded From DvDPlayer-Manual.com Philips Manuals
12
XP AZ1145/00-1 08-05-2000 15:42 Pagina 13
AZ 1145/00 page
13
TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING:
Do not open the set as there is a risk of electric shock. Under no circumstances should you try to repair the set yourself, as this would invalidate the guarantee.
PROBLEM
– POSSIBLE CAUSE
• REMEDY
No sound/power
– VOLUME not adjusted
• Adjust the VOLUME
– Headphones connected
• Disconnect headphones
– Mains lead not securely connected
• Connect the mains lead properly
Severe radio hum or noise
– Electrical interference: set too close to TV,
VCR or computer
• Increase the distance
Poor radio reception
– Weak radio signal
• FM: Direct the FM telescopic aerial for optimum reception
• MW/LW: Turn the set for optimum reception
indication
– CD-R(W) is blank or the disc is not finalised
• Use a finalised CD-R(W)
– CD badly scratched or dirty
• Replace/ clean CD, see CD player and
CD handling
The CD skips tracks
– CD is damaged or dirty
• Replace or clean the CD
– SHUFFLE or a programme is active
• Switch off SHUFFLE/PROGRAM
Poor cassette sound quality
– Dust and dirt on the heads, etc.
• Clean deck parts etc., see Maintenance
– Use of incompatible cassette types (METAL or CHROME)
• Only use NORMAL (IEC I) for recording
Recording does not work
– Cassette tab(s) may be broken
• Apply a piece of adhesive tape over the missing tab space
or indication
– No CD inserted
• Insert a CD
– CD badly scratched or dirty
• Replace/ clean CD, see CD player and
CD handling
– Laser lens steamed up
• Wait until lens has cleared
Remote control does not function properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
This product complies with the radio interference requirements of the European Union.
The type plate is located on the bottom of the set.
Downloaded From DvDPlayer-Manual.com Philips Manuals
13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement