PremierLink™
Water Source Heat Pump
Controller
Installation, Start-Up and
Configuration Instructions
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PremierLink Controller Hardware. . . . . . . . . . . . . . . . . 1
Field-Supplied Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 2
• SPACE TEMPERATURE (SPT) SENSOR
• INDOOR AIR QUALITY CO2 SENSOR
PremierLink Controller Inputs and Outputs . . . . . . 3
Control Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Install Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
• SPACE TEMPERATURE (SPT) SENSOR
INSTALLATION
• INDOOR AIR QUALITY CO2 SENSOR
INSTALLATION
Connect to CCN Communication Bus . . . . . . . . . . . . 8
• COMMUNICATIONS BUS WIRE
SPECIFICATIONS
START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8,9
Perform System Check-Out . . . . . . . . . . . . . . . . . . . . . . 8
Initial Operation and Test. . . . . . . . . . . . . . . . . . . . . . . . . 8
Install Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Forcing Values and Configuring Items . . . . . . . . . . . 9
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-24
Points Display Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Thermostat Control Input Screen. . . . . . . . . . . . . . . . 12
Alarm Service Configuration Screen . . . . . . . . . . . . 12
Controller Identification Screen . . . . . . . . . . . . . . . . . 13
Holiday Configuration Screen . . . . . . . . . . . . . . . . . . . 13
Occupancy Configuration Screen . . . . . . . . . . . . . . . 13
Set Point Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Service Configuration Selection Screen. . . . . . . . . 15
PremierLink Configuration Screen . . . . . . . . . . . . . . 18
Occupancy Maintenance Screen . . . . . . . . . . . . . . . . 20
Maintenance Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disconnect all power to the unit before performing maintenance or service. Unit may automatically start if power is
not disconnected. Electrical shock and personal injury
could result.
GENERAL
The PremierLink Controller is a factory-installed control
compatible with the Carrier Comfort Network (CCN). This
control is designed to allow users the access and ability to
change factory-defined settings thus expanding the function of
the standard unit control board. The complete PremierLink
package consists of a factory-installed control circuit board
with the Complete C unit controls, leaving water temperature
sensor, and discharge air sensor.
IMPORTANT: Verify that configurations for AC-HP and
Auxout are correct for proper equipment operation. See
page 18.
Carrier’s diagnostic standard tier display tools such as
Navigator or Scrolling Marquee can be used with the PremierLink controller. Access is available via an RJ-11 connection or
a 3-wire connection to the communication bus. User interfaces
available for use with the CCN system are PCs equipped with
Carrier user interface software such as Service Tool, ComfortVIEW™, or ComfortWORKS®. When used as part of the
CCN, other devices such as the CCN data transfer, Linkage
Thermostat, or Comfort Controller can read data from or write
data to the PremierLink controller.
INSTALLATION
Inspection — Inspect unit contents for visual defects that
may have occurred during shipping. If there is any damage,
contact your local representative before proceeding.
PremierLink Controller Hardware — When a CCN
SAFETY CONSIDERATIONS
SAFETY NOTE
Air-handling equipment will provide safe and reliable service
when operated within design specifications. The equipment
should be operated and serviced only by authorized personnel who have a thorough knowledge of system operation,
safety devices and emergency procedures.
Use good judgement when applying any manufacturer’s
instructions to avoid injury to personnel or damage to equipment and property.
system is installed, a factory-mounted PremierLink controller
is provided with the water source heat pump (WSHP) units.
The package from the factory includes:
• PremierLink controller.
• Supply air temperature sensor.
• Leaving water temperature sensor.
PREMIERLINK CONTROLLER — PremierLink controllers
can be provided with any Aquazone™ water source heat pump
product by selecting this option in the model number nomenclature. The PremierLink controller is provided with, and includes all the features of, the Complete C unit controller. The
specific functionality of PremierLink is described in detail in
dedicated Carrier literature. Factory-supplied wiring (except
space temperature sensor [SPT]) is illustrated in Fig. 1.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
PC 111
Catalog No. 535-00091
Printed in U.S.A.
Form 50-9SI
Pg 1
11-02
Replaces: New
Book 1 4
Tab 5a 5a
SUPPLY AIR TEMPERATURE SENSOR — A factoryinstalled supply air temperature sensor is provided with
PremierLink™ controller for the water source heat pump
equipment. The sensor is a 10k ohm thermistor, which is
installed in and protected by a stainless steel housing probe.
Probe size is 1/4 in. diameter by 1.5 in. long. Wire size and type
are 22 AWG (American Wire Gage), 7/30 copper wire, and
PVC white, 2 conductors.
LEAVING WATER TEMPERATURE SENSOR — A factoryinstalled leaving water temperature sensor is provided with
PremierLink controller for the water source heat pump equipment. The sensor is a 10k ohm thermistor, which is installed in
and protected by a stainless steel housing probe. Probe size is
1/ in. diameter by 1.5 in. long. Wire size and type are 22 AWG,
4
7/30 copper wire, and PVC white, 2 conductors.
SPACE TEMPERATURE (SPT) SENSOR — A field-supplied
Carrier space temperature sensor is required to maintain the
space temperature in sensor mode. There are three sensors available for this application:
• 33ZCT55SPT, Space Temperature Sensor with Override
Button
• 33ZCT56SPT, Space Temperature Sensor with Override
Button and Set Point Adjustment
• 33ZCT58SPT, Communicating Room Sensor with Override
Button, Set Point Adjustment, and Manual Fan control
INDOOR AIR QUALITY CO2 SENSOR — An indoor air
quality sensor is required for CO2 level monitoring. Three
different CO2 sensors are available for this application:
• 33ZCSENCO2 sensor is an indoor, wall-mounted sensor
with an LED (light-emitting diode) display
• 33ZCT55CO2 sensor is an indoor, wall-mounted sensor
without display. The CO2 sensor also includes a space temperature sensor with override button
• 33ZCT56CO2 sensor is an indoor, wall-mounted sensor
without display. The CO2 sensor also includes a space temperature sensor with override button and temperature offset
Field-Supplied Hardware — The PremierLink controller is configurable with the following field-supplied sensors:
• space temperature sensor (33ZCT55SPT, 33ZCT56SPT, or
33ZCT58SPT) in sensor mode or thermostat mode for
economizer control
• indoor air quality sensor (33ZCSENCO2, 33ZCT55CO2,
33ZCT56CO2) required only for demand control
ventilation
For specific details about sensors, refer to the literature
supplied with the sensor.
COMPLETE
C
CONTROL
PREMIER
LINK
PWR
Y
HS1/EXH/RVS
W
CR
CR
O
G
R
C
CMP1
FAN
AL2
PWR
J1
J8
AL1
J5
J6
S
A
T
L
W
T
J4
CMPSAFE
S
P
T
A
LEGEND
CR — Control Relay
LWT — Leaving Water Temperature Sensor
SAT — Supply Air Temperature Sensor
SPT — Space Temperature Sensor
NOTE: Reversing valve is on in Cooling mode.
Fig. 1 — Typical Factory-Installed PremierLink Wiring for WSHP Units
(Except SPT Sensor — Field Installed)
2
PremierLink™ Controller Inputs and Outputs —
NOTE: When connecting the communication bus cable, a
color code system for the entire network is recommended to
simplify installation and checkout. See Table 2 for the recommended color code.
3. Use 4-connector Molex with red, white and black wires
to connect the communication wires. Verify the color
codes in Table 2 to ensure the Red (+) wire connects
to Terminal 1. Connect the White (ground) wire to Terminal 2. Connect the Black (–) wire to Terminal 3.
4. Secure all connections in Step 3 with wire nuts.
5. Insert the plug into the existing 4-pin mating connector
on the base module in the main control box
(Terminal J-2).
6. Restore power.
The PremierLink controller inputs and outputs are shown in
Table 1.
Disconnect electrical power before wiring the PremierLink controller. Electrical shock, personal injury, or
damage to the PremierLink controller can result.
Control Wiring — The PremierLink controller can be
connected to either a Carrier-approved thermostat or CCN
compatible temperature sensor.
1. Turn off power to the control box.
2. Strip the ends of the red, white, and black conductors of
the communication bus cable.
Table 1 — PremierLink Controller Inputs and Outputs
INPUTS
SPACE TEMPERATURE (SPT)
SET POINT ADJUSTMENT (STO)
SUPPLY AIR TEMPERATURE (SAT)
LEAVING WATER TEMPERATURE
IAQ SENSOR (IAQI)
OUTDOOR AQ SENSOR (OAQ) (NOT USED)
REMOTE TIME CLOCK (RMTOCC)
COMPRESSOR LOCKOUT (CMPSAFE)
FIRE SHUTDOWN (FSD)
SUPPLY FAN STATUS (SFS)
NOT USED
ENTHALPY STATUS (ENTH) (NOT USED)
OUTPUTS
ECONOMIZER (ECONPOS) (NOT USED)
FAN (SF)
COOL STAGE 1 (CMP1)
COOL STAGE 2 (CMP2)
HEAT STAGE 1 (HS1)
HEAT STAGE 2 (HS2
HEAT 3/EXHAUST/REVERSING VALVE (HS3/EXH/RVS)
POWER
AI (10K Thermistor)
AI (10K Thermistor)
AI (10 K Thermistor)
AI (10K Thermistor)
(4-20 mA)
(4-20 mA)
DI (24 VAC)
DI (24 VAC)
DI (24 VAC)
DI (24 VAC)
TERMINAL(S)
J6-7, J6-6
J6-5, J6-6
J6-3, J6-4
J6-1, J6-2
J5-5, J5-6
J5-2, J5-3
J4-11, J4-12
J4-9, J4-10
J4-7, J4-8
J4-5, J4-6
DI (24 VAC)
POWER
4-20 mA
DO Relay (24 VAC, 1A)
DO Relay (24 VAC, 1A)
DO Relay (24 VAC, 1A)
DO Relay (24 VAC, 1A)
DO Relay (24 VAC, 1A)
DO Relay (24 VAC, 1A)
J4-1, J4-2
TERMINALS
J9-1, J9-2
J8-18
J8-15
J8-12
J8-9
J8-6
J8-3
LEGEND
AI — Analog Input
DI — Digital Input
DO — Digital Output
Table 2 — Color Code Recommendations
SIGNAL TYPE
+
Ground
–
CCN BUS WIRE COLOR
Red
White
Black
3
CCN PLUG PIN NUMBER
1
2
3
Install Sensors (See Fig. 2-6) — The PremierLink™
NOTE: See Table 3 for thermistor resistance vs temperature
values.
Wiring the Space Temperature Sensor — To wire the sensor,
perform the following (see Fig. 2-4):
1. Identify which cable is for the sensor wiring.
2. Strip back the jacket from the cables for at least 3 inches.
Strip 1/4-in. of insulation from each conductor. Cut the
shield and drain wire from the sensor end of the cable.
3. Connect the sensor cable as follows:
a. Connect one wire from the cable to (BLU) wire on
J6-7 analog connector on the controller. Connect
the other end of the wire to the left terminal on the
SEN terminal block of the sensor.
b. Connect another wire from the cable to (BRN)
J6-6 analog connector on the controller. Connect
the other end of the wire to the remaining open terminal on the SEN terminal block.
c. On 33ZCT56SPT thermostats, connect the remaining wire to the (BLK) STO on J6-5 connector on
the controller. Connect the other end of the wire
to the right terminal on the SET terminal block of
the sensor.
d. In the control box, install a no. 10 ring type crimp
lug on the shield drain wire. Install this lug under
the mounting screw of the PremierLink controller.
e. On 33ZCT56SPT thermostats install a jumper
between the two center terminals (right SEN and
left SET). See Fig. 3.
f. Refer to Fig. 4 for 33ZCT58SPT thermostat wiring. Once the T58 sensor is powered up, all of the
graphic icons on the LCD display will be energized
for a few seconds. The icons will then turn off and
the T58 sensor will energize the three-digit
numeric display. The value “58” will be displayed
for two seconds. After 2 seconds, the LCD will display the default space temperature value.
NOTE: See Fig. 5 for space temperature sensor averaging.
controller can be used with either the T58 Communicating sensor or any combination of CO2 and space temperature sensors.
Refer to the instructions supplied with each sensor for electrical
requirements.
NOTE: All space and indoor air quality sensors are fieldinstalled accessories.
SPACE TEMPERATURE (SPT) SENSOR INSTALLATION — There are three types of SPT sensors available from
Carrier: The 33ZCT55SPT space temperature sensor with
timed override button, the 33ZCT56SPT space temperature
sensor with timed override button and set point adjustment, and
the 33ZCT58SPT T58 communicating room sensor with
timed override button, set point adjustment, and manual fan
control. See Fig. 2, 3 and 6 for sensor wiring.
The space temperature sensors are used to measure the
building interior temperature. The T58 communicating room
sensors measure and maintain room temperature by communicating with the controller. Sensors should be located on an
interior building wall. The sensor wall plate accommodates
the NEMA (National Electrical Manufacturers Association)
standard 2 x 4 junction box. The sensor can be mounted directly on the wall surface if acceptable by local codes.
Do not mount the sensor in drafty locations such as near air
conditioning or heating ducts, over heat sources such as baseboard heaters, radiators, or directly above wall-mounted lighting dimmers. Do not mount the sensor near a window which
may be opened, near a wall corner, or a door. Sensors mounted
in these areas will have inaccurate and erratic sensor readings.
The sensor should be mounted approximately 5 ft from the
floor, in an area representing the average temperature in the
space. Allow at least 4 ft between the sensor and any corner
and mount the sensor at least 2 ft from an open doorway. The
SPT sensor wires will be connected to terminals on the unit
main control board.
Install the sensor as follows:
1. Locate the two Allen type screws at the bottom of the
sensor.
2. Turn the two screws clockwise to release the cover from
the sensor wall mounting plate.
3. Lift the cover from the bottom and then release it from
the top fasteners.
4. Feed the wires from the electrical box through the opening in the center of the sensor mounting plate.
5. Using two no. 6-32 x 1 mounting screws (provided with
the sensor), secure the sensor to the electrical box.
NOTE: The sensor may also be mounted directly on
the wall using 2 plastic anchors and 2 sheet metal
screws (field-supplied).
6. Use 20 gage wire to connect the sensor to the controller.
The wire is suitable for distances of up to 500 ft. Use a
three-conductor shielded cable for the sensor and set
point adjustment connections. The standard CCN
communication cable may be used. If the set point adjustment (slidebar) is not required, then an unshielded, 18 or
20 gage, two-conductor, twisted pair cable may be used.
The CCN network service jack requires a separate,
shielded CCN communication cable. Always use separate cables for CCN communication and sensor wiring. (Refer to Fig. 2-4 for wire terminations.)
7. Replace the cover by inserting the cover at the top of the
mounting plate first, then swing the cover down over the
lower portion. Rotate the two Allen head screws counterclockwise until the cover is secured to the mounting plate
and locked in position.
Table 3 — Thermistor Resistance vs Temperature
Values for Space Temperature Sensor,
Supply Air Temperature Sensor, and
Outdoor Air Temperature Sensor
TEMP
(C)
–40
–35
–30
–25
–20
–15
–10
–5
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
4
TEMP
(F)
–40
–31
–22
–13
–4
5
14
23
32
41
50
59
68
77
86
95
104
113
122
131
140
149
158
RESISTANCE
(Ohms)
335,651
242,195
176,683
130,243
96,974
72,895
55,298
42,315
32,651
25,395
19,903
15,714
12,494
10,000
8,056
6,530
5,325
4,367
3,601
2,985
2,487
2,082
1,752
FIELD WIRING
T58 SENSOR
VAC
J4-3 (24 VAC)
24 VAC
COM
2
1
3
4
5
6
RED(+)
WHT(GND)
BLK(-)
CCN COM
SEN
J6-6 SDT (COM)
CCN-
BLACK (-)
GND
WHITE (GND)
CCN+
RED (+)
CCN
COM
SW1
BRN (GND)
BLU (SPT)
SENSOR WIRING
BLACK (-)
WHITE (GND)
J2
(COM)
RED (+)
Fig. 4 — T58 Communicating Sensor
Typical Wiring (33ZCT58SPT)
INDOOR AIR QUALITY CO2 SENSOR INSTALLATION
(IAQ) — The indoor air quality sensor accessory monitors
carbon dioxide (CO2) levels. This information is used to monitor IAQ levels. Three types of sensors are provided. The wall
sensor can be used to monitor the conditioned air space.
Sensors use infrared technology to measure the levels of CO2
present in the air. The wall sensor is available with or without
an LCD readout to display the CO2 level in ppm.
The CO2 sensors are all factory set for a range of 0 to
2000 ppm and a linear mA output of 4 to 20. Refer to the
instructions supplied with the CO2 sensor for electrical requirements and terminal locations.
To accurately monitor the quality of the air in the conditioned air space, locate the sensor near a return air grille (if
present) so it senses the concentration of CO2 leaving the
space. The sensor should be mounted in a location to avoid
direct breath contact.
Do not mount the IAQ sensor in drafty areas such as near
supply ducts, open windows, fans, or over heat sources. Allow
at least 3 ft between the sensor and any corner. Avoid mounting
the sensor where it is influenced by the supply air; the sensor
gives inaccurate readings if the supply air is blown directly onto
the sensor or if the supply air does not have a chance to mix
with the room air before it is drawn into the return airstream.
Wiring the Indoor Air Quality Sensor — To wire the sensors
after they are mounted in the conditioned air space, see Fig. 6
and the instructions shipped with the sensors. For each sensor,
use two 2-conductor 18 AWG (American Wire Gage) twistedpair cables (unshielded) to connect the separate isolated 24 vac
power source to the sensor and to connect the sensor to the control board terminals. To connect the sensor to the control,
identify the positive (4 to 20 mA) and ground (SIG COM) terminals on the sensor. Connect the 4-20 mA terminal to terminal
IAQ (RED) and connect the SIG COM terminal to terminal
GND (BRN).
Fig. 2 — Space Temperature Sensor
Typical Wiring (33ZCT55SPT)
1
2
3
4
SEN
SW1
5
6
RED(+)
WHT(GND)
BLK(-)
CCN COM
SET
BLK
(T56)
BRN (GND)
BLU (SPT)
SENSOR WIRING
JUMPER
TERMINALS
AS SHOWN
Cool
Warm
Fig. 3 — Space Temperature Sensor
Typical Wiring (33ZCT56SPT)
5
J6
6
7
RED
RED
BLK
BLK
RED
RED
RED
BLK
BLK
BLK
SENSOR 1
SENSOR 2
SENSOR 3
SENSOR 4
SPACE TEMPERATURE AVERAGING — 4 SENSOR APPLICATION
J6
RED
RED
BLK
BLK
BLK
LEGEND
Factory Wiring
BLK
SENSOR 1
SENSOR 3
SENSOR 2
RED
BLK
7
RED
RED
6
RED
RED
BLK
BLK
SENSOR 4
SENSOR 6
SENSOR 5
Field Wiring
RED
RED
BLK
BLK
SENSOR 8
SENSOR 7
SPACE TEMPERATURE AVERAGING — 9 SENSOR APPLICATION
Fig. 5 — Space Temperature Averaging
6
SENSOR 9
7
Fig. 6 — PremierLink™ Controller and Sensor Wiring — 33ZCT55SPT, 33ZCT56SPT, 33ZCT58SPT Space Temperature Sensors;
33ZCSENCO2 (Outdoor), and 33ZCT55CO2, 33ZCT56CO2 (Indoor) Air Quality Sensors
Connect to CCN Communication Bus — The
PremierLink™ controller connects to the bus in a daisy chain
arrangement. Negative pins on each component must be
connected to respective negative pins (and likewise positive
pins on each component must be connected to respective positive pins). The controller signal pins must be wired to the signal
ground pins. Wiring connections for CCN must be made at the
3-pin plug.
At any baud (9600, 19200, 38400), the number of controllers is limited to 239 devices maximum. Bus length may not
exceed 4000 ft, with no more than 60 total devices on any
1000-ft section. Optically isolated RS-485 repeaters are
required every 1000 ft.
NOTE: Carrier device default is 9600 baud.
COMMUNICATION BUS WIRE SPECIFICATIONS —
The CCN Communication Bus wiring is field-supplied and
field-installed. It consists of shielded three-conductor cable
with drain (ground) wire. The cable selected must be identical
to the CCN Communication Bus wire used for the entire network. See Table 4 for recommended cable.
Perform System Check-Out
1. Check the correctness and tightness of all power and
communication connections.
2. At the unit, check fan and system controls for proper
operation.
3. At the unit, check electrical system and connections of
any optional electric reheat coil.
4. Check to be sure the area around the unit is clear of
construction dirt and debris.
5. Check that final filters are installed in the unit. Dust and
debris can adversely affect system operation.
6. Verify that the PremierLink controls are properly
connected to the CCN bus.
Initial Operation and Test — Perform the following
procedure:
1. Apply 24 vac power to the control.
2. Connect the service tool to the phone jack service port of
the controller.
3. Using the Service Tool, upload the controller from
address 0, 31 at 9600 baud rate. The address may be set at
this time. Make sure that Service Tool is connected to
only one unit when changing the address.
Table 4 — Recommended Cables
MANUFACTURER
Alpha
American
Belden
Columbia
CABLE PART NO.
2413 or 5463
A22503
8772
02525
Install Navigator — The Navigator is a portable display module that conforms to NEMA 4 specifications for
outdoor use in temperatures ranging from –22 F (–30 C) to
158 F (70 C). The Navigator can be used to configure and
perform service diagnostics on machines equipped with the
PremierLink Controller. See Fig. 7.
The Navigator keypad contains eleven menu LEDs and one
Alarm Status LED, all of which are red. The Navigator is capable of displaying four 24-character lines of information on a
backlit liquid crystal display. The Navigator has four functional
keys which are the up arrow ( ), down arrow ( ),
ENTER and ESCAPE keys.
NOTE: Conductors and drain wire must be at least 20 AWG,
stranded, and tinned copper. Individual conductors must be
insulated with PVC, PVC/nylon, vinyl, Teflon, or polyethylene. An aluminum/polyester 100% foil shield and an outer
jacket of PVC, PVC/nylon, chrome vinyl, or Teflon with a
minimum operating temperature range of –20 C to 60 C is
required.
The communication bus shields must be tied together at
each system element. If the communication bus is entirely
within one building, the resulting continuous shield must be
connected to ground at only one single point. If the communication bus cable exits from one building and enters another
building, the shields must be connected to the grounds at a
lightning suppressor in each building (one point only).
INSTALLATION — The Navigator display module is intended to be a mobile device, so there are no holes in the device for
permanent mounting. The module has a magnetic mount that is
strong enough to hold the device in place on any clean, dry
metal surface.
START-UP
Com
NA
The unit must be electrically grounded in accordance with
local codes and NEC ANSI/NFPA 70 (American National
Standards Institute/National Fire Protection Association).
T IM E
EWT
LW T
SETP
Use the Carrier network communication software to start up
and configure the PremierLink™ controller.
Changes can be made using the ComfortWORKS® software, ComfortVIEW™ software, or Network Service Tool.
The Network Service Tool is a portable interface device that
allows the user to change system set-up and set points from a
zone sensor or terminal control module. During start-up, the
Carrier software can also be used to verify communication
with PremierLink controller.
NOTE: All set-up and set point configurations are factoryset and field-adjustable.
For specific operating instructions, refer to the literature
provided with user interface software.
MO
fort
VIG
Lin
ATO
R
k
12.
54. 58
44. 6°F
4 4 . 01 ° F
°F
DE
Run
Statu
s
Servi
ce Te
st
Temp
eratur
es
Pres
sures
Setpo
ints
Inputs
Outpu
ts
Confi
gurat
ion
Time
Cloc
k
Opera
ting
Mode
s
Al ar
m St
atu
s
ESC
Alarm
s
ENT
ER
Fig. 7 — Navigator in Display Mode
8
used to select a menu item or to accept data entry. The
ESCAPE key is used to exit to the next highest mode or to
cancel data entry. The sub-mode and item displays will wrap
around with the last and first items separated by a line of dashes
on the display. The ‘>’ symbol is the pointer and is located at
the left side of the display.
Press the ESCAPE key to display “Select a menu item” on
the screen. This is the top level and the arrow keys are used to
move the red LED to the one of the 11 desired modes. Pressing
ENTER will display the sub-modes within a top level mode.
Once in a sub-mode, use the arrow keys to move the pointer
(‘>’) to the desired sub-mode. Up to four sub-modes will be
displayed on the Navigator at one time. Continue pressing the
arrow keys as needed to find the desired sub-mode.
To enter LEN (local equipment network) mode:
1. Remove power by removing the connection to J1.
2. Remove the connection to J2 (to avoid communication
problems with equipment).
3. Position the DIP switch to 0 (ON) position.
4. Restore power by reconnecting J1.
5. Plug in the Navigator.
The controller is now in LEN mode and will support the
Navigator device.
To return to CCN mode:
1. Remove power to the controller by removing the connection to J1.
2. Remove the connection to J2 (to avoid communication
problems with equipment).
3. Position the DIP switch to 1 (OFF) position.
4. Reconnect J2.
5. Restore power by reconnecting J1.
The controller is now in CCN mode at the previously configured address and baud rate.
The Navigator module is powered through the PremierLink™ controller. The Navigator has a modular telephone style
(RJ14) connector and should be connected to terminal block
TB3 in the control box. This device is intended for use on the
LEN communications bus only. Do NOT connect to the Navigator while in CCN mode. Communication problems may
occur.
OPERATION — To use the Navigator, plug the RJ14 connector into the RJ14 port. On power up, the Navigator displays:
PremierLink
Navigator
By
Carrier
As an example, Press the ESCAPE key to display “Select
a menu item” on the screen. Press the down arrow until the red
LED is lit for the Setpoints menu. Press the ENTER key to
display the first four sub-modes in the Setpoints menu:
>SETP
OATL
NTLO
UHDB
To access the sub-mode to change the Unoccupied OAT
Lockout Setpoint, press the down arrow to scroll down until
the Navigator display reads:
SETP
OATL
>NTLO
UHDB
To view an expansion of the sub-mode, press the ENTER
and ESCAPE keys simultaneously and the Navigator will
display:
The Navigator will upload the appropriate display tables
from the PremierLink controller. A ‘Communication failure’
message will be displayed if any errors are encountered. Check
the wiring at the connector. After successful upload of information, the Navigator begins its default display. All items in the
Run Status menu are displayed one at a time in this mode. An
example of the display in the default mode is:
>NTLO
UNOCC. OAT LOCKOUT
TEMP
The Navigator will remain in the expanded display mode
until the ESCAPE key is pressed. Use the arrow keys to view
expansions for any of the other sub-modes within the Setpoint
mode.
SAT 54.2 °F
SUPPLY AIR TEMPERATURE
The different levels of modes can be accessed with the
Navigator. See the base unit controls and troubleshooting guide
for more information.
Pressing any key while in the default display mode will
cause the Navigator to enter its manual mode. In this mode, all
sub-modes and items within the eleven top level configuration
modes, denoted on the display screen, can be accessed. The
Navigator automatically returns to the default display mode after 60 minutes of no keypad activity. Pressing the ENTER and
ESCAPE keys simultaneously while the unit displays “Select
a menu item” will also log the device out and return it to its default display mode.
Password Protection — If an area is entered that is
password protected or an item is selected for change that is
password protected, the Navigator will display:
Enter Password
1111 (default password)
The first digit of the password will be flashing. Hold either
of the arrow keys down to change the value of the first digit (if
necessary) and press ENTER to accept. Repeat the process for
the remaining three digits.
The message “Invalid Password” is displayed if the password is not correct. The password can not be disabled from the
Navigator, nor can it be changed.
NAVIGATING THROUGH MENU STRUCTURES — The
arrow keys are used to scroll up and down to select sub-modes
within a mode or items within a sub-mode. See the base unit
troubleshooting guide for menu structure. The ENTER key is
Forcing Values and Configuring Items — Certain
items are allowed to be forced and other items are userconfigurable. Both of these changes can be made using the
Navigator.
9
CONFIGURATION
CONTROL SET POINT — This point displays the current
controlling set point when a heat or cool mode is active. If there
is not an active heat or cool set point, the set point of the last
mode is displayed. Upon reset or start-up, the proper cooling
set point is displayed, depending on occupancy. In the thermostat mode, this point is not used for equipment control.
Control Set Point: Display Units:
Degrees F (Degrees C)
Default Value:
Unoccupied Cool
Setpoint
Display Range: 35 to 110
Network Access: Read Only
COOLING PERCENT TOTAL CAPACITY — The Cooling
Percent Total Capacity point is used to display the current
Cooling Capacity. When cooling is enabled, the percent of
cooling being delivered is determined by the following formula
for the number of compressor stages confirmed:
% Output Capacity = (# of active stages/Total stages) * 100.
Cooling Percent
Total Capacity: Display Units:
% output capacity
Default Value:
0
Display Range: 0 to 100
Network Access: Read Only
HEATING PERCENT TOTAL CAPACITY — The Heating
Percent Total Capacity point is used to display the current
Heating Capacity.
When heat is enabled, the percent of heat being delivered is
determined by the following formula for gas or electric heat:
% Output Capacity = (# of active stages/Total stages) * 100
Heating Percent
Total Capacity: Display Units:
% output capacity
Default Value:
0
Display Range: 0 to 100
Network Access: Read Only
The following sections describe the computer configuration
screens which are used to configure the PremierLink™ controller. The screens shown may be displayed differently when
using different Carrier software.
Points Display Screen — The Points Display screen is
used to monitor and change the PremierLink controller set
points. See Table 5.
SPACE TEMPERATURE — This point displays the space
temperature from the 10K thermistor (Type III) located in the
space.
Space
Temperature:
Display Units:
Degrees F (Degrees C)
Default Value:
–40.0
Display Range: –40.0 to 245.0
Network Access: Read/Write
SUPPLY AIR TEMPERATURE — The Supply Air Temperature point displays the temperature of the air leaving the unit,
downstream of any cool or heat sources. The temperature is
measured by a 10K thermistor (Type III). This sensor is
required for proper function of the heating and cooling.
Supply Air
Temperature:
Display Units:
Degrees F (Degrees C)
Default Value:
0.0
Display Range: –40.0 to 245.0
Network Access: Read/Write
LEAVING WATER TEMPERATURE — Temperature of the
water leaving the WSHP downstream of any cool or heat
sources, measured by a 10K thermistor (Type III). This sensor
is required for proper function of the heating and cooling.
Leaving Water
Temperature:
Display Units:
Degrees F (Degrees C)
Default Value:
0.0
Display Range: –40.0 to 245.0
Network Access: Read/Write
Table 5 — Points Display
DESCRIPTION
Space Temperature
Supply Air Temperature
Leaving Water Temperature*
Control Setpoint
Cooling % Total Capacity
Heating % Total Capacity
Economizer Active (Not Used)
Supply Fan Relay
Supply Fan Status
Economizer Position (Not Used)
Current Min Damper Pos
Filter Status
Remote Occupied Mode
Heat Stage 1
Heat Stage 2
Heat 3/Exhaust/Rev Valve
Enthalpy (Not Used)
Indoor Air Quality
Indoor Air Quality Setpt
Outdoor Air Quality (Not Used)
Fire Shutdown
SPT Offset
Compressor 1
Compressor 2
Compressor Safety
VALUE
72.2
67.1
48.8
0.0
0
0
Yes
On
On
26.2
20
Clean
Off
Off
Off
Off
Low
367.9
1050.0
0.0
Normal
0.0
Off
Off
Off
UNITS
dF
dF
dF
dF
%
%
STATUS
FORCE
%
%
Sensor failure
^F
*If OAT broadcast is enabled from a controller in the system, the leaving water temperature may be displayed
temporarily by removing the force left by the OAT broadcast.
NOTE: Bold values indicate points that can be forced through communications.
10
NAME
SPT
SAT
OAT
CLSP
CCAP
HCAP
ECOS
SF
SFS
ECONPOS
IQMP
FLTS
RMTOCC
HS1
HS2
H3_EX_RV
ENTH
IAQI
IAQS
OAQ
FSD
STO
CMP1
CMP2
CMPSAFE
REMOTE OCCUPIED MODE — This point displays the
status of the remote time clock input. This input is only available when the controller is being used in sensor control mode.
When the Remote Start point is on, and the zone controller is
not controlled by a Linkage Thermostat, the controller will
function in an occupied mode. When the Remote Start point is
off, the controller will revert to its own occupancy schedule.
Remote
Occupied Mode: Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read/Write
ECONOMIZER ACTIVE (NOT USED) — The Economizer
Active point displays the status of the economizer for free cooling. When the outdoor conditions match the desired indoor
conditions, the economizer will be enabled for outdoor air
assisted cooling.
Economizer
Active:
Display Units:
Discrete ASCII
Default Value:
No
Display Range: No/Yes
Network Access: Read Only
SUPPLY FAN RELAY — This point displays the commanded state of the Supply Fan Relay.
Supply Fan
Relay:
Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read/Write
SUPPLY FAN STATUS — This point displays the Supply
Fan status if the controller is configured to receive input from
the Supply Fan. Otherwise this point will display the output
state of the Supply Fan Relay. This mode can only be used
when the controller is in sensor control mode.
Supply Fan
Status:
Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read Only
ECONOMIZER DAMPER POSITION (NOT USED) —
This point displays the current commanded damper position of
the economizer 4 to 20 mA on the J-9 connector. The 4 to
20 mA signal is scaled linearly over the range of 0 to 100% of
the Supply Fan Relay.
NOTE: Although not normally used for Aquazone™ applications, this output may be used to control a fresh-air damper for
a demand control ventilation strategy.
Economizer
Position:
Display Units:
% Open
Default Value:
0
Display Range: 0 to 100
Network Access: Read/Write
CURRENT MINIMUM DAMPER POSITION — This point
displays the current minimum damper position if an Indoor Air
Quality routine is not active. If an Indoor Air Quality sensor is
installed and the differential air quality set point has been
exceeded, this point will display the current calculated minimum position deemed necessary to maintain the air quality in
the space.
Current Minimum
Damper Position: Display Units:
% Open
Default Value:
0
Display Range: 0 to 100
Network Access: Read Only
FILTER STATUS — The filter status point will be shown as
“CLEAN” until the run time of the fan exceeds the configured
Filter Timer Hours. When the user-configured Filter Timer
Hours has been exceeded, the Filter Status will display
“DIRTY” and a CCN alarm will be generated. Forcing the
point to “CLEAN” will clear the alarm condition and will reset
the timer. (Setting the configured filter timer value to zero will
provide the same function.) The value of the timer is stored in
EEPROM to protect it in the event of a power failure. This is
done periodically every 24 hours. The filter timer function only
operates if the configured filter timer value (FLTTMR) is a
non-zero number.
Filter Status:
Display Units:
Discrete ASCII
Default Value:
Clean
Display Range: Clean/Dirty
Network Access: Read/Write
HEAT STAGE 1 — The Heat Stage 1 point provides the state
of the Heating 1 output.
Heating Stage 1: Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read Only
HEAT STAGE 2 — The Heat Stage 2 point provides the state
of the Heating 2 output.
Heating Stage 2: Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read Only
HEAT STAGE 3, EXHAUST FAN, OR REVERSING
VALVE — This point displays the commanded state of auxiliary output. This output can be configured to control a third
stage of heat, an exhaust fan, or a reversing valve on some heat
pump units.
In the exhaust fan mode with continuous exhaust configured, this point may control a bank of lights or another
indicator that should remain ON whenever the controller is in
the occupied mode.
Heat 3, Exhaust,
Rev Valve:
Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read Only
ENTHALPY (NOT USED) — This point displays the current status of an outdoor air or differential enthalpy input. This
point may be broadcast to other controllers or received from
a controller which supports global broadcast of the ENTH
variable.
Enthalpy:
Display Units:
Discrete ASCII
Default Value:
High
Display Range: High/Low
Network Access: Read/Write
INDOOR AIR QUALITY (IAQ) — The Air Quality point
displays the indoor air quality reading from a CO2 sensor
installed in the space. The CO2 sensor maintains differential
indoor air quality for demand control ventilation per ASHRAE
Standard 62-1999. The controller can be configured to generate
an alarm when the control is in occupied mode and the CO2
level exceeds the high or low limit set.
Indoor Air
Quality (ppm):
Display Units:
None shown (parts per
million implied)
Default Value:
0
Display Range: 0 to 5000
Network Access: Read/Write
11
COMPRESSOR SAFETY — When the controller is in
sensor mode, this point can be used to monitor the status of the
compressor trouble output supplied with some equipment.
When the input is detected, the controller will energize all
available stages to satisfy the demand and issue a compressor
trouble alert on the communications network.
Compressor
Safety:
Display Units:
Discrete ASCII
Display Range: Off/On
Default Value:
Off
Network Access: Read Only
INDOOR AIR QUALITY SET POINT — This point displays the current Indoor Air Quality set point. The set point is
determined by the configured Indoor Air Quality differential
and the current outdoor air quality value. If an outdoor air
quality value is not received, the controller will assume a
default outdoor level of 400 ppm and calculate the set point
using that value.
Indoor Air Quality
Set Point:
Display Units:
None shown (parts per
million implied)
Default Value:
0
Display Range: 0 to 5000
Network Access: Read Only
Thermostat Control Input Screen — The Thermostat Control Input Display is used to display the input status of
equipment requests from the thermostat (TSTAT). See Table 6.
OUTDOOR AIR QUALITY (NOT USED) — This point displays the reading from an outdoor air quality sensor. This point
supports global broadcast of outdoor air quality on a network.
Outdoor Air Quality
Set Point:
Display Units:
None shown (parts per
million implied)
Default Value:
0
Display Range: 0 to 5000
Network Access: Read/Write
Alarm Service Configuration Screen — The Alarm
Service Configuration is used to configure the alarms used on
the PremierLink™ controller. See Table 7.
ALARM ROUTING CONTROL — The Alarm Routing
Control indicates which CCN system software or devices will
receive and process alarms sent by the PremierLink controller.
This decision consists of eight digits which can be set to zero or
one. A setting of one indicates alarms should be sent to this
device. A setting of zero disables alarm processing for that
device. Currently the corresponding digits are configured for
the following devices: first digit is for user interface software
(ComfortWORKS®, ComfortVIEW™, etc.); second digit is
for Autodial Gateway or Telink; fourth digit is for Alarm Printer Interface Module, DataLINK module; digits 3 and 5 through
8 are unused.
Alarm Routing
Control:
Range:
00000000 to 1111111
Default Value:
00000000
FIRE SHUTDOWN — While in sensor control mode, this
point can be used to receive a signal from a smoke detector or
fire panel to shut down the Supply Fan and all heating and
cooling stages.
Fire Shutdown: Display Units:
Discrete ASCII
Default Value:
Normal
Display Range: Normal/Alarm
Network Access: Read/Write
SPT OFFSET — This point displays the value of the Space
Temperature offset calculated from the input of a T56 sensor
slide bar.
SPT Offset:
Display Units:
Delta Degrees F
(Delta Degrees C)
Default Value:
0.0
Display Range: –15 to 15
Network Access: Read/Write
ALARM RE-ALARM TIME — This decision is used to configure the number of minutes that will elapse between
re-alarms. A re-alarm occurs when the condition that caused
the initial alarm continues to persist for the number of minutes
specified. Re-alarming continues to occur at the specified
interval until the alarm condition no longer exists.
Re-Alarm Time: Display Units:
Minutes
Display Range: 0 to 1440
Default Value:
0 (Disabled)
CONTROL TEMPERATURE HYSTERESIS — This configuration defines the range above the high set point and below
the low set point the space temperature must exceed for an
alarm condition to exist during occupied hours.
For example, if the current setpoint is 75 F and the hysteresis value is 5 F, an alarm will be generated if the space temperature exceeds the low limit of 70 F or the high limit of 80 F.
Control
Temperature
Hysteresis:
Display Units:
Delta Degrees F
(Delta Degrees C)
Range:
1.0 to 100.0
Default Value:
5.0
COMPRESSOR 1 — This point displays the commanded
state of the compressor 1 output.
Compressor 1:
Display Units:
Discrete ASCII
Default Value:
Off
Display Range: Off/On
Network Access: Read Only
COMPRESSOR 2 — This point displays the commanded
state of the compressor 2 output.
Compressor 2:
Display Units:
Discrete ASCII
Range:
Off/On
Default Value:
Off
Network Access: Read Only
Table 6 — Thermostat Control Input Display
DESCRIPTION
Y1 - Call for Cool 1
Y2 - Call for Cool 2
W1 - Call for Heat 1
W2 - Call for Heat 2
G - Call for Fan
VALUE
On
On
Off
Off
On
UNITS
12
STATUS
FORCE
NAME
Y1
Y2
W1
W2
G
SUPPLY AIR TEMPERATURE — HIGH LIMIT — The
Supply Air Temperature High Limit alarm is used to monitor
the value of the supply air temperature within a specified range.
If the supply air temperature becomes too high, an alarm condition will exist.
Supply Air
Temperature
High Limit:
Display Units:
Degrees F (Degrees C)
Display Range: –40.0 to 245.0
Default Value:
150.0
Table 8 — Controller Identification
DESCRIPTION
Description:
Location:
Software Part Number:
Model Number:
Serial Number:
Reference Number:
DURATION — The Duration field indicates how long the
holiday will last (in days).
Duration:
Range:
0 to 365
Default Value:
0
As an example, if a Holiday is configured for Month 2,
Day 5, Duration 2, then the Holiday will start February 5 and
end February 7.
Table 9 — Holiday Configuration
Table 7 — Alarm Service Configuration
00000000
0
5.0
45.0
150.0
0.0
1200.0
UNITS
DESCRIPTION
Start Month
Start Day
Duration
NAME
min
^F
ALRMCNT
REALARM
SPTHYS
dF
dF
LOWLIM
HIGHLIM
0002000001
Version 1.100
NAME
DevDesc
Location
PartNum
ModelNum
SerialNo
RefNum
START DAY — The Start Day field is used to determine
which day the holiday will start.
Start Day:
Range:
1 to 31
Default Value:
1
INDOOR AIR QUALITY ALERT LIMIT — The IndoorAir Quality Alert Limit alarm defines the allowable CO2 levels
during occupied periods. If the CO2 levels become too low or
too high during occupied periods, an alarm condition will exist.
Indoor Air Quality
Low Limit:
Display Units: PPM (implied)
Display Range: 0.0 to 5000.0
Default Value: 0.0
Indoor Air Quality
High Limit
Display Units: PPM (implied)
Display Range: 0.0 to 5000.0
Default Value: 1200.0
VALUE
CESR131269-01
UNITS
Holiday Configuration Screen — The Holiday Configuration screen is used by the PremierLink controller to store
configuration fields for up to twelve holidays. See Table 9.
START MONTH — The Start Month field is used to configure the month that the holiday will start. The numbers 1
through 12 are used to indicate which month is specified.
Start Month:
Range:
1 to 12
Default Value:
1 (January)
SUPPLY AIR TEMPERATURE — LOW LIMIT — The
Supply Air Temperature Low Limit alarm is used to monitor
the value of the supply air temperature within a specified range.
If the supply air temperature becomes too low, an alarm condition will exist.
Supply Air
Temperature
Low Limit:
Display Units: Degrees F (Degrees C)
Display Range: –40.0 to 245.0
Default Value: 45.0
DESCRIPTION
Alarm Control
Alarm Routing Control
Realarm Time
Control Temp Hysteresis
Supply Air Temperature
Low Limit
High Limit
IAQ High Alert Limit
Low Limit
High Limit
VALUE
Rooftop Control
VALUE
1
1
0
UNITS
NAME
MONTH
DAY
DURATION
Occupancy Configuration Screen — The Occupancy Configuration Screen is used to configure the occupancy
schedule for the PremierLink controller. See Table 10.
MANUAL OVERRIDE HOURS — The Manual Override
Hours point is used to command a timed override by entering
the number of hours the override will be in effect. If the occupancy schedule is occupied when this number is downloaded,
the current occupancy period will be extended by the number
of hours downloaded.
If the current occupancy period is unoccupied when the
occupancy override is initiated, the mode will change to occupied for the duration of the number of hours downloaded. If the
occupancy override is due to end after the start of the next
occupancy period, the mode will transition from occupancy
override to occupied without becoming unoccupied and the
occupancy override timer will be reset.
An active occupancy override or a pending occupancy
override may be canceled by downloading a zero to this
configuration. Once a number other than zero has been downloaded to this configuration, any subsequent downloads of any
value other than zero will be ignored by the controller.
Manual Override
Hours:
Units:
hours
Range:
0 to 4
Default Value:
0
LOWLIM
HIGHLIM
Controller Identification Screen — The controller
identification screen contains reference information used to
identify the PremierLink™ controller. See Table 8.
DESCRIPTION — The Description point displays the type of
device.
LOCATION — The Location point shows the location of the
device.
SOFTWARE PART NUMBER — The Software Part Number indicates the part number of the software being used.
MODEL NUMBER — The Model Number indicates the
model number of the device being used.
SERIAL NUMBER — The Serial Number indicates the serial
number of the device being used.
REFERENCE NUMBER — The Reference Number indicates the version of the software being used.
13
Set Point Screen — The Set Point screen is used to con-
OCCUPANCY SCHEDULE — For scheduling flexibility, the
occupancy programming is broken into eight separate periods.
For each period the schedule contains the following fields: Day
of Week, Occupied From, and Occupied To.
figure the occupied and unoccupied set points. See Table 11.
OCCUPIED LOW — The Occupied Low set point describes
the low temperature limit of the space during Occupied mode.
Occupied Low: Units:
Degrees F (Degrees C)
Range:
40.0 to 90.0
Default Value:
70.0
DAY OF WEEK — The Day of Week configuration consists
of eight fields corresponding to the seven days of the week and
a holiday field in the following order: Monday, Tuesday,
Wednesday, Thursday, Friday, Saturday, Sunday, Holiday.
It is displayed as:
M T W Th Fr Sa Su Hol
0 0 0 0 0 0 0 0
If a 1 is configured in the corresponding place for a certain
day of the week, the related “Occupied from” and “Occupied
to” times for that period will take effect on that day of the
week. If a 1 is placed in the holiday field, the related times will
take effect on a day configured as a holiday. A zero means the
schedule period will not apply to that day.
Day of week:
Range:
0 or 1
Default Values: 11111111 for period 1,
00000000 for the rest of
the periods
OCCUPIED HIGH — The Occupied High set point describes
the high temperature limit of the space during Occupied mode.
Occupied High: Units:
Degrees F (Degrees C)
Range:
45.0 to 99.9
Default Value:
74.0
UNOCCUPIED LOW — The Unoccupied Low set point
describes the low temperature limit of the space during
Unoccupied mode.
Unoccupied Low: Units:
Degrees F (Degrees C)
Range:
40.0 to 90.0
Default Value:
75.0
UNOCCUPIED HIGH — The Unoccupied High set point describes the high temperature limit of the space during Unoccupied mode.
Unoccupied High: Units:
Degrees F (Degrees C)
Range:
45.0 to 99.9
Default Value:
90.0
HIGH OAT LOCKOUT FOR THERMOSTAT (NOT
USED) — The High OAT Lockout for Thermostat function
determines if the Economizer Damper is able to adjust the
Space Temperature based on the current temperature value of
OAT (outdoor air temperature).
High OAT
Lockout:
Units:
Degrees F (Degrees C)
Range:
55.0 to 75.0
Default Value:
65.0
UNOCCUPIED OAT LOCKOUT TEMPERATURE (NOT
USED) — The Unoccupied OAT Lockout Temperature
describes the lowest Outdoor Air Temperature allowed for
Unoccupied Free Cooling operation. This function is also used
by IAQ Pre-Occupancy Purge control to determine the minimum damper position.
Unoccupied
OAT Lockout:
Units:
Degrees F (Degrees C)
Range:
40.0 to 70.0
Default Value:
50.0
OCCUPIED FROM — This field is used to configure the
hour and minute, in military time, that the mode for the
PremierLink controller will switch to occupied.
Occupied From: Units:
Hours:Minutes
Range:
00:00 to 24:00
(Minutes 00 to 59)
Default Value:
00:00
OCCUPIED TO — This field is used to configure the hour
and minute, in military time, that the mode for the PremierLink
controller switches from occupied to unoccupied.
Occupied To:
Units:
Hours:Minutes
Range:
00:00 to 24:00
(Minutes 00 to 59)
Default Value:
24:00
Table 10 — Occupancy Configuration
DESCRIPTION
Manual Override Hours
Period 1: Day of Week
Period 1: Occupied from
Period 1: Occupied to
Period 2: Day of Week
Period 2: Occupied from
Period 2: Occupied to
Period 3: Day of Week
Period 3: Occupied from
Period 3: Occupied to
Period 4: Day of Week
Period 4: Occupied from
Period 4: Occupied to
Period 5: Day of Week
Period 5: Occupied from
Period 5: Occupied to
Period 6: Day of Week
Period 6: Occupied from
Period 6: Occupied to
Period 7: Day of Week
Period 7: Occupied from
Period 7: Occupied to
Period 8: Day of Week
Period 8: Occupied from
Period 8: Occupied to
VALUE
0
11111111
00:00
24:00
00000000
00:00
24:00
00000000
00:00
24:00
00000000
00:00
24:00
00000000
00:00
24:00
00000000
00:00
24:00
00000000
00:00
24:00
00000000
00:00
24:00
UNITS
hours
NAME
OVRD
DOW1
OCC1
UNOCC1
DOW2
OCC2
UNOCC2
DOW3
OCC3
UNOCC3
DOW4
OCC4
UNOCC4
DOW5
OCC5
UNOCC5
DOW6
OCC6
UNOCC6
DOW7
OCC7
UNOCC7
DOW8
OCC8
UNOCC8
UNOCCUPIED HEATING DEADBAND — The Unoccupied Heating Deadband describes the space temperature value
which has to be achieved while Heating before the Heating
mode will turn off.
Unoccupied
Heating
Deadband:
Units:
Delta Degrees F
(Delta Degrees C)
Range:
0.0 to 10.0
Default Value:
1.0
UNOCCUPIED COOLING DEADBAND — The Unoccupied Cooling Deadband describes the space temperature value
which has to be achieved while Cooling before the Cooling
mode will turn off.
Unoccupied
Cooling
Deadband:
Units:
Delta Degrees F
(Delta Degrees C)
Range:
0.0 to 10.0
Default Value:
1.0
14
LOW TEMPERATURE MINIMUM POSITION (NOT
USED) — The Low Temperature Minimum Position describes
the low temperature limit for Low Outdoor Air Temperature
conditions.
IAQ Pre-Occupancy Purge Algorithm will use this value
whenever Outdoor Air Temperature is below Unoccupied OAT
Lockout Temperature.
Low Temperature
Minimum
Position:
Units:
Percent
Range:
0 to 100
Default Value:
10.0
The Cooling PID includes the following set points: Proportional Gain, Integral Gain, Derivative Gain, and Starting Value.
Proportional Gain: Range:
0.0 to 40.0
Default Value:
6.0
Integral Gain:
Range:
0.0 to 10.0
Default Value:
3.0
Derivative Gain:
Range:
0.0 to 20.0
Default Value:
5.0
Starting Value:
Units:
Degrees F
Range:
40.0 to 90.0
Default Value:
70.0
HIGH TEMPERATURE MINIMUM POSITION (NOT
USED) — The High Temperature Minimum Position specifies
the value for Purge Minimum Damper Position for High
Outdoor Air temperature conditions.
IAQ Pre-Occupancy Purge Algorithm shall use this value
whenever Outdoor Air Temperature is above or at Unoccupied
OAT Lockout Temperature, and also OAT is above Occupied
Cool Set Point or Enthalpy is High. Whenever OAT>=NTLO
and OAT<=OCSP and Enthalpy is Low, the Purge algorithm
will set Purge Minimum Damper Position to 100%.
High Temperature
Minimum
Position:
Units:
Percent
Range:
0 to 100
Default Value:
35.0
Table 12 — Service Configuration Selection
DESCRIPTION
Cooling PID
Proportional Gain
Integral Gain
Derivative Gain
Starting Value
Staged Cooling
Total Number of Stages
Stage 1 Time Guard
Stage 2 Time Guard
Stage 3 Time Guard
Heating PID
Proportional Gain
Integral Gain
Derivative Gain
Starting Value
Staged Heating
Total Number of Stages
Stage 1 Time Guard
Stage 2 Time Guard
Stage 3 Time Guard
IAQ PID
Proportional Gain
Integral Gain
Derivative Gain
Starting Value
Economizer PID (Not Used)
Proportional Gain
Integral Gain
Derivative Gain
Starting Value
Submaster Gain Limit
Submaster Center Value
Damper Movement Band
(Not Used)
OAT Temp Band (Not Used)
Minimum Damper Position
(Not Used)
Low Temp MDP Override
(Not Used)
DX Cooling Lockout
DX Cooling Lockout Temp
SAT CMP1 Lockout Temp
SAT CMP2 Lockout Temp
Time Guard Override
Continuous Power Exhaust
(Not Used)
Supply Fan Status Enable
Max Offset Adjustment
Space Temp Trim
Supply Air Temp Trim
POWER EXHAUST SET POINT (NOT USED) — The Power Exhaust Set Point describes the minimum damper position
that the Economizer Damper must be before the power exhaust
fan will be energized.
Power Exhaust
Set Point:
Units:
Percent
Range:
0 to 100
Default Value:
50.0
Table 11 — Set Point Configuration
DESCRIPTION
Setpoints
Occupied Low Setpoint
Occupied High Setpoint
Unoccupied Low Setpoint
Unoccupied High Setpoint
Hi OAT Lckout for TSTAT
(Not Used)
Unocc. OAT Lockout TEMP
(Not Used)
Unocc. Heating Deadband
Unocc. Cooling Deadband
Low Temp. Min. Position
(Not Used)
Hi Temp. Min. Position
(Not Used)
Power Exhaust Setpoint
(Not Used)
VALUE
70.0
74.0
69.0
75.0
65.0
50.0
1.0
1.0
10
35
50
UNITS
NAME
dF
dF
dF
dF
dF
OHSP
OCSP
UHSP
UCSP
OATL
dF
NTLO
^F
^F
%
UHDB
UCDB
LTMP
%
HTMP
%
PES
Service Configuration Selection Screen — The
Service Configuration Selection screen is used to configure
the service set points of the PremierLink™ controller. See
Table 12.
COOLING PID — The PremierLink controller reads the
space temperature sensor and compares the temperature to
the current high set point. If it exceeds the set point, and
cooling is configured and available, the controller then calculates the required supply air temperature to satisfy the given
conditions.
15
VALUE
6.0
3.0
5.0
70.0
UNITS
NAME
dF
KP
KI
KD
STARTVAL
2
Enable
Enable
Disable
6.0
3.0
5.0
75.0
STAGES
TG1
TG2
TG3
dF
2
Enable
Enable
Enable
0.1
0.0
0.0
0.0
-4.0
-2.0
-3.0
70.0
-5.5
60
0
25
20
100
On
45.0
55.0
50.0
Off
STAGES
TG1
TG2
TG3
%
KP
KI
KD
STARTVAL
%
%
KP
KI
KD
STARTVAL
ESG
CTRVAL
ECONBAND
^F
%
TEMPBAND
MDP
%
LOWMDP
dF
dF
dF
dF
Disable
Disable
2.0
0.0
0.0
KP
KI
KD
STARTVAL
^F
^F
^F
DXCTLO
DXLOCK
SATL01
SATL02
TGO
MODPE
SFSENABL
LIMT
RATTRIM
SATTRIM
IAQ PID — The proportional gain affects the response of PID
calculations for staged control. The gain is also used for two
position control to establish the hysteresis between on and off.
A larger gain speeds response time or reduces the hysteresis,
while a smaller gain requires a larger error to generate the same
response to changes in Indoor Air Quality. Enter the desired
proportional gain for the Indoor Air Quality control algorithm.
The integral gain affects the PID calculation; an increase
will make the IAQ submaster reference change greater as the
error in indoor air quality increases. The integral gain should be
selected to eliminate proportional droop without overshoot.
Enter the desired integral gain for the Indoor Air Quality control algorithm.
The Derivative Gain is typically not required for Indoor Air
Quality operation and should be left at the default value.
The Starting Value is used to establish the starting value for
the IAQ PID calculation.
The IAQ PID includes the following set points: Proportional Gain, Integral Gain, Derivative Gain, and Starting Value.
Proportional Gain:Range:
–100.0 to 40.0
Default Value:
1.0
Integral Gain:
Range:
–5.0 to 5.0
Default Value:
0.5
Derivative Gain: Range:
–20.0 to 20.0
Default Value:
0.0
Starting Value:
Units:
Percent
Range:
0.0 to 100.0
Default Value:
0.0
ECONOMIZER PID (NOT USED) — The proportional gain
determines the response of the PID temperature control loop; a
larger gain increases the amount of damper movement while a
smaller gain requires a larger error to achieve the same results.
The integral gain affects the response of a PID calculation;
an increase in gain will compensate more quickly for proportional control droop. Too large of an integral gain will cause
excessive damper positioning and instability. Enter the desired
integral gain for the damper control algorithm.
The economizer derivative gain has been tested for ideal
operation in sensor mode and should be left at the default value.
NOTE: In thermostat mode, the modulation may appear to
regularly change. However, it will precisely control leaving-air
temperature.
The economizer Starting Value is used to establish the starting value for the damper PID calculation. The value entered is
determined by the mass of the zone. Typically a value of 10%,
the default, will be adequate for most applications. For higher
mass areas, such as a stone lobby, the value may be increased
to 20 to 25%.
The Economizer PID includes the following set points:
Proportional Gain, Integral Gain, Derivative Gain, and Starting
Value.
Proportional Gain: Range:
–100.0 to 100.0
Default Value:
–4.0
Integral Gain:
Range:
–5.0 to 5.0
Default Value:
–2.0
Derivative Gain:
Range:
–20.0 to 20.0
Default Value:
–3.0
Starting Value:
Units:
Degrees (F)
Range:
48.0 to 120.0
Default Value:
70.0
STAGED COOLING — The staging function is used for DX
(direct expansion) cooling (1 or 2 stages). The staging function
uses the cooling submaster reference from the PID and compares the value to the supply air temperature to calculate the
required number of output stages to energize.
Time Guard delays are provided to allow for up to 2 stages
of compression. Also, a DX Lockout will prevent operation
of the DX cooling if the outdoor air temperature is below this
value.
The cooling algorithm controls the valve or stages of DX
cooling to prevent the space temperature from exceeding the
current cooling set point (which includes any calculated offset
value from a T56 sensor slide bar during occupied periods).
Also, the cooling is controlled so that the supply air temperature does not fall below 50 F when cooling is active.
Number of Stages: Range:
1 to 3
Default Value:
2
The Time Guards must be set to Enable for output to a
compressor, and set to Disable for output to a valve or
compressor unloader.
Stage 1
Time Guard:
Range:
Disable/Enable
Default Value:
Enable
Stage 2
Time Guard:
Range:
Disable/Enable
Default Value:
Enable
Stage 3
Time Guard:
Range:
Disable/Enable
Default Value:
Disable
HEATING PID — The PremierLink controller determines if a
heating demand exists in the space. The controller reads the
space temperature sensor and compares the temperature to the
current low set point (including any calculated offset value
from a T56 or T57 sensor) during occupied periods. If it is
below the set point, and heating is configured and available, it
then calculates the required supply air temperature to satisfy
the given conditions. The calculated value (heating submaster
reference) is compared to the actual supply-air temperature and
the output is then adjusted to satisfy conditions by using a
Proportional/Integral/Derivative (PID) loop.
The Heating PID includes the following set points: Proportional Gain, Integral Gain, Derivative Gain, and Starting Value.
Proportional Gain: Range:
–100.0 to 100.0
Default Value:
6.0
Integral Gain:
Range:
–5.0 to 5.0
Default Value:
3.0
Derivative Gain:
Range:
–20.0 to 20.0
Default Value:
5.0
Starting Value:
Units:
Degrees F
Range:
40.0 to 120.0
Default Value:
75.0
STAGED HEATING — The Staged Heating function is used
for two-position valves or for electric heat (1 or 2 stages). The
staging function uses the heating submaster reference value
from the PID and compares it to the supply air temperature to
calculate the required number of output stages to energize.
Number of Stages: Range:
1 to 3
Default Value:
2
Stage 1
Time Guard:
Range:
Disable/Enable
Default Value:
Enable
Stage 2
Time Guard:
Range:
Disable/Enable
Default Value:
Enable
Stage 3
Time Guard:
Range:
Disable/Enable
Default Value:
Enable
16
SUBMASTER GAIN LIMIT — The Submaster Gain Limit
is used to define the submaster gain limit that is multiplied by
the Submaster Error and added to the Submaster Center Value
to produce the output value that will be sent to the device. The
sign of the submaster gain limit determines the direction in
which the output will be driven in response to a given error.
The gain is expressed in percent change in output per
degree of error.
Submaster Gain
Limit Reference:
Range:
–20.0 to 20.0
Default Value:
–5.5
DX COOLING LOCKOUT — The DX (Direct Expansion)
Cooling Lockout function Enables/Disables Low Ambient DX
Cooling Lockout option. When DX Cooling Lockout is
enabled, Cooling control will compare OAT against the DX
Cooling Lockout Temperature. Whenever OAT <= the DX
Cooling Lockout Temperature and current DX stages are 0, the
control will set Cooling Submaster Reference (CCSR) to
150 F. That will prevent the unit from staging up.
DX Cooling
Lockout:
Range:
On/Off
Default Value:
On
SUBMASTER CENTER VALUE — The Submaster Center
Value is used to define the submaster loop center value which
defines the starting point of the loop. This value typically represents the midpoint of the range of the device being controlled.
Submaster Center
Value Reference:
Units:
Percent
Range:
0 to 100
Default Value:
60
DAMPER MOVEMENT BAND (NOT USED) — The Damper Movement Band is used to define what the minimum desired range of change in economizer damper position that is
required before the controller will attempt to open/close the
economizer.
Damper Movement
Reference:
Units:
Percent
Range:
0 to 5
Default Value:
0
DX COOLING LOCKOUT TEMPERATURE — The DX
Cooling Lockout Temperature specifies Low Ambient DX
Cooling Lockout Temperature that is compared against OAT to
determine if the unit can stage up or not.
DX Cooling
Lockout Temp: Units:
Degrees F (Degrees C)
Range:
40.0 to 60.0
Default Value:
45.0
SAT CMP1 LOCKOUT TEMP — The SAT CMP1 Lockout
Temperature displays the low supply temperature set point for
compressor no. 1 supply air during cooling. If compressor no. 1
is on during Cooling mode, the economizer will assist the cooling and work to maintain a discharge air temperature slightly
above lockout temperature set point. If the economizer is at
minimum and the supply air temperature goes below Lockout
Temperature set point, the compressor will cycle to maintain
the supply air set point. The minimum on and off times will
still be in effect.
SAT CMP1
Lockout Temp: Units:
Degrees F (Degrees C)
Range:
50.0 to 65.0
Default Value:
55.0
SAT CMP2 LOCKOUT TEMP — The SAT CMP2 Lockout
Temperature displays the low supply temperature set point for
compressor no. 2 supply air during cooling. If compressor no. 2
is on during Cooling mode, the economizer will assist the cooling and work to maintain a discharge air temperature slightly
above lockout temperature set point. If the economizer is at
minimum and the supply air temperature goes below Lockout
Temperature set point, the compressor will cycle to maintain
the supply air set point. The minimum on and off times and
stage-up and down timers will still be in effect.
SAT CMP2
Lockout Temp: Units:
Degrees F (Degrees C)
Range:
45.0 to 55.0
Default Value:
50.0
OAT TEMP BAND — The OAT Temp Band is used to slow
the response of the economizer damper based on the value of
OAT. In other words, the colder OAT gets the slower the rate
of change in the economizer.
OAT Temp
Reference:
Range:
0 to 40 Delta Degrees F
(Delta Degrees C)
Default Value: 25.0
MINIMUM DAMPER POSITION (NOT USED) — The minimum damper position (MDP) specifies user configured occupied minimum economizer damper position. The control
selects the greatest value between MDP and IAQ calculated
Minimum Position. The resulting value is the Final Minimum
Damper Position IQMP for Occupied mode.
Economizer Damper is limited to IQMP in Occupied mode,
or whenever Supply Fan is ON in units with Thermostat
control.
Minimum Damper
Position:
Units:
Percent
Range:
0 to 100
Default Value:
20.0
LOW TEMP MINIMUM DAMPER POSITION OVERRIDE (NOT USED) — The Low Temperature Minimum
Damper Position (MDP) specifies the value for purge
minimum damper position for low outdoor air temperature
conditions.
The IAQ Pre-Occupancy Purge Algorithm shall use this
value for the minimum damper position whenever Outdoor Air
Temperature is below Unoccupied OAT Lockout Temperature.
The Low Temperature MDP must be lower than the configured Minimum Damper Position.
Low Temperature
MDP Override:
Units:
Percent
Range:
0 to 100
Default Value:
100
TIME GUARD OVERRIDE — The Time Guard Override
function will reset the Time Guard. Whenever this option is
changed from OFF to ON, the control will evaluate the amount
of time left in Compressor Time Guards.
If the time in a Time Guard is more than 30 seconds, it will
be replaced with 30 seconds.
NOTE: Changing this decision from OFF to ON will only
result in one-time Time Guards override.
To perform the override again, the override must be
changed from OFF to ON again.
Time Guard
Override:
Range:
On/Off
Default Value:
Off
17
CONTINUOUS POWER EXHAUST (NOT USED) — The
Continuous Power Exhaust function defines the operation of
the Power Exhaust Fan.
If disabled, the Power Exhaust Fan will operate during
economizer purge cycles when the economizer damper position is above the configured minimum value. If enabled, the
Power Exhaust Fan will follow the supply fan's operation.
Continuous
Power
Exhaust:
Range:
Disable/Enable
Default Value:
Disable
Table 13 — PremierLink Control Configuration
DESCRIPTION
0=TSTAT, 1=CCN Sensor
0=Gas, 1=Electric Heat
(Not Used)
0=AC Unit, 1=Heat Pump
Auxiliary Output
0=None
1=Exhaust Fan
2=Heat Stage
3=Reversing Valve
Unoccupied Free Cool
(Not Used)
Demand Limiting
Loadshed Group Number
CCN Broadcast OAT, ENTH,OAQ
Global Schedule Broadcast
Broadcast Acknowledge
Schedule Number
Timed Override Hours
Linkage Thermostat
Cool Strt Bias(min/deg)
Heat Strt Bias(min/deg)
Filter Timer hrs* 100
IAQ Priority Level
IAQ Pre-Occupancy Purge
IAQ Purge Duration
IAQ Delta Setpoint
IAQ Maximum Damper Pos.
Indoor AQ Low Ref.
Indoor AQ High Ref.
Outdoor AQ Low Ref. (Not Used)
Outdoor AQ High Ref. (Not Used)
Outdoor AQ Lockout Point
(Not Used)
Service Password
Password Enable
Metric Display
SUPPLY FAN STATUS ENABLE — The Supply Fan Status
Enable function is enabled when an actual sensor input is used
to determine that the supply fan is on. If the supply fan status is
OFF when the fan should be running, Heat, Cool and Economizer will be disabled.
If this decision is disabled, the Supply Fan Status will follow the state of the Supply Fan Relay in order to allow the
algorithms to run that depend on the Supply Fan Status to be
ON before executing.
Supply Fan
Status Enable:
Range:
Disable/Enable
Default Value:
Disable
MAXIMUM OFFSET ADJUSTMENT — Maximum Offset
Adjustment value determines the degree in which the occupied
heating and cooling set points can be adjusted by the setpoint
adjustment slide bar on the space temperature sensor.
Max Offset
Adjustment:
Units:
Delta Degrees F
(Delta Degrees C)
Range:
0.0 to 15.0
Default Value:
2.0
SPACE TEMPERATURE TRIM — The Space Temperature
Trim configuration is used to calibrate the temperature display
for a sensor that does not appear to be reading correctly.
Space Temperature
Trim:
Units:
Delta Degrees F
(Delta Degrees C)
Range:
–9.9 to 9.9
Default Value:
0.0
VALUE UNITS NAME
0
TSTATCFG
HEATTYPE
0
1
3
AC
AUXOUT
NTEN
Disable
Disable
1
0
No
No
64
0 hours
DLEN
LSGP
OATBC
GSBC
BCACK
SCHEDNUM
TIMOVRID
10
10
15
Low
Disable
5
650
50
0.0
2000.0
0.0
2000.0
KCOOL
KHEAT
FIL_TIMR
IAQP
IAQPURGE
IQPD
IAQD
IAQMAXP
IIAQREFL
IIAQREFH
OIAQREFL
OIAQREFH
OIAQLOCK
0
1111
Disable
Off
min
min
min
%
PASSWORD
PASS_EBL
DISPUNIT
HEAT TYPE (NOT USED) — The Heat Type mode determines the type of heat equipment the controller uses. There are
two choices: gas or electric.
Heat Type:
Range:
0 for Gas
1 for Electric Heat
Default Value:
0 (Gas)
SUPPLY AIR TEMPERATURE TRIM — The Supply Air
Temperature Trim configuration is used to calibrate the temperature display for a sensor that does not appear to be reading
correctly.
Supply Air
Temperature
Trim:
Units:
Degrees F (Degrees C)
Range:
–9.9 to 9.9
Default Value:
0.0
UNIT TYPE — The Unit Type mode determines the type of
heating/cooling equipment the controller is attached to. There
are two choices: AC or Heat Pump.
The AC mode is primarily used for units using the compressors for cooling only.
The Heat Pump mode is primarily used for units using a
heat pump (for example, compressors for heating and cooling).
Unit Type:
Range:
0 for AC
1 for Heat Pump
Default Value:
1 (Heat Pump)
Staging is as follows for gas electric units (AC = 0), Carrier
heat pumps with a defrost board (AC = 1), or cooling units with
electric heat (AC = 0 or 1 and HEATYPE = 1):
If Heating PID STAGES = 2
(HCAP = 50% capacity) energized HS1.
(HCAP = 100% capacity) energizes HS2.
If Heating PID STAGES = 3 and AUXOUT = HS3
(HCAP = 33% capacity) energizes HS1
(HCAP = 66% capacity) energizes HS2
(HCAP = 100% capacity) energizes H3_EX_RVS
PremierLink™ Configuration Screen — The PremierLink Configuration screen allows the user to configure all
functions. See Table 13.
OPERATING MODE — The Operating Mode function
determines the operating mode of the PremierLink controller.
There are two operating modes from which to choose: TSTAT
and CCN Sensor.
The TSTAT mode allows PremierLink controller to operate
as a stand-alone thermostat control by monitoring Y1 (cooling
stage 1), Y2 (cooling stage 2), W1 (heating stage 1), W2 (heating stage 2), and G (indoor fan) inputs.
The CCN mode allows the controller to integrate into a
Carrier Comfort Network.
Operating Mode: Range:
0 for TSTAT
1 for CCN
Default Value:
0 (TSTAT)
18
GLOBAL SCHEDULE BROADCAST — The Global Schedule Broadcast setting configures the controller to broadcast or
receive a global schedule. If set to Yes, the controller will act as
a global schedule master and its schedule will be broadcast to
the CCN. If set to No, the controller will not broadcast a global
schedule and it will receive the configured schedule number.
Global Schedule
Master:
Range:
No/Yes
Default Value:
No
Staging occurs as follows for heat pump (AC = 1) units and
(AUXOUT = 3) configured for reversing valve:
If Heating PID STAGES = 2
(HCAP = 50% capacity) energizes CMP1 and CMP2,
then 2 seconds later energizes H3_EX_RVS.
(100% capacity) energizes HS1 and HS2.
If Heating PID STAGES = 3
(33% capacity if) energizes CMP1 and CMP2, then
2 seconds later energizes H3_EX_RVS.
(66% capacity) energizes HS1
(100% capacity) energizes HS2
BROADCAST ACKNOWLEDGER — The Broadcast Acknowledger setting configures the controller to recognize
broadcast messages that appear on its CCN bus.
NOTE: For proper CCN bus operation, there should be only
one device per CCN bus that is configured as the Broadcast
Acknowledger.
Acknowledger: Range:
No/Yes
Default Value:
No
AUXILIARY OUTPUT — The Auxiliary Output function is
used to define the specific use of the Auxiliary Output on the
controller board.
The output will be energized or deenergized by the appropriate algorithm that uses that specific output.
Auxiliary Output is displayed as one of the following:
0 = None
2 = Heat Stage
1 = Exhaust Fan
3 = Reversing Valve
Auxiliary Output:
Range:
0 to 3
Default Value: 3
UNOCCUPIED FREE COOL (NOT USED) — The Unoccupied Free Cool function is used during unoccupied periods to
pre-cool the space using outside air when outside conditions
are suitable.
Unoccupied
Free Cool:
Range:
Disable/Enable
Default Value:
Disable
SCHEDULE NUMBER — The Schedule Number determines which Global Occupancy Schedule that the controller
will follow. A value of 64 disables global occupancy from
CCN and will decide Occupancy from its local schedule. A
value between 65 and 99 will allow the controller to follow the
global occupancy schedule of the number broadcast over CCN.
Occupancy Schedule
Number
Range:
64 to 99
Default Value:
64
TIMED OVERRIDE HOURS — The Timed Override Hours
function is used to configure a timed override duration by
entering the number of hours the override will be in effect.
Pressing the override button on a space temperature sensor will
cause an override.
Timed Override
Hours:
Range:
0 to 4
Default Value:
0
DEMAND LIMITING — The Demand Limiting function is
used to limit operating capacity of the unit to prevent system
overloads. Both Heating and Cooling capacity is limited.
When the Demand Limit option is enabled, the control will
respond to the Loadshed Controller commands, such as Redline Alert, Shed, Unshed, and Redline Cancel. If equipped with
the expansion I/O board, the control will also respond to the
Loadshed Hardware input.
Demand
Limiting:
Range:
Disable/Enable
Default Value:
Disable
LOADSHED GROUP NUMBER — The Loadshed Group
Number function defines the Loadshed table number (LDSHDxxS, where xx is the configured loadshed group number) that
the controller will respond to when a broadcast for Redline/
Loadshed has been detected on the CCN bus.
Unoccupied
Free Cool:
Range:
1 to 16
Default Value:
1
LINKAGE THERMOSTAT — The Linkage Thermostat start
time biases allow the installer to configure the time (per degree) the space should take to recover in the Heat and Cool
modes for optimum start with a Linkage Thermostat. These
numbers will be used to calculate the Start Bias time.
Cool Start Bias: Units:
Minutes/Degree
Range:
0 to 60
Default Value:
10
Heat Start Bias
Units:
Range:
Default Value:
Minutes/Degree
0 to 60
10
FILTER TIMER HOURS — The Filter Timer Hours configuration determines when the filter status will display a “Dirty”
alarm. When the Filter Timer Hours is configured to a value
other than zero and fan run time exceeds the value configured,
the filter status will display “Dirty” and a CCN alarm will be
generated. Setting the configured Filter Timer Hours value to
zero will disable the alarm condition. The value of the timer is
stored in EEPROM to protect it in the event of a power failure.
The value is stored every 24 hours.
Filter Timer
Hours:
Range:
0 to 99
Default Value: 15 (where 15*100=1500)
CCN, BROADCAST OAT, ENTHALPY, OAQ — Configures the controller to CCN broadcast any or all of the point
values for Outside Air Temperature (OAT), Enthalpy (ENTH),
and Outdoor Air Quality (OAQ).
Example: To broadcast OAQ and ENTH but not OAT, the corresponding bitmap is 110; the binary equivalent of the decimal
number 6. The configuration decision would then be set to a 6.
CCN Broadcast, OAT, Enthalpy,
OAQ Allowable Entries:
0 — None
5 — OAT and OAQ
1 — OAT Only
6 — ENTH and OAQ
2 — ENTH Only
7 — OAT, ENTH and OAQ
3 — OAT and ENTH
4 — OAQ Only
Default Value:
0 (disabled, no broadcasts performed)
19
High Reference specifies the High Point of the Indoor IAQ
Sensor Range in ppm.
High Reference: Units:
PPM (parts per million)
Range:
0 to 5000
Default Value:
2000
OUTDOOR AIR QUALITY SENSOR (NOT USED) —
The Outdoor Air Quality sensor defines the value in parts per
million (ppm) which correlates to the low and high voltage
readings from the sensor.
Low Reference specifies the Low Point of the Outdoor IAQ
Sensor Range in ppm.
Low Reference: Units:
PPM (parts per million)
Range:
0 to 5000
Default Value:
0
High Reference specifies the High Point of the Outdoor
IAQ Sensor Range in ppm.
High Reference: Units:
PPM (parts per million)
Range:
0 to 5000
Default Value:
2000
INDOOR AIR QUALITY PRIORITY LEVEL — The Indoor
Air Quality Priority Level, when set to Low, ensures that comfort is not being compromised by bringing in too much outdoor
air to maintain IAQ set point. When an override condition
takes place, IAQ control is disabled, and Economizer Minimum Position is set to the user configured value MDP. When
set to High, IAQ control is always active regardless of indoor
comfort conditions. The controller will temper cold air OAT
<55 F to prevent cold blow.
Indoor Air Quality
Priority Level:
Range:
High/Low
Default Value:
Low
INDOOR AIR QUALITY PREOCCUPANCY PURGE —
The Indoor Air Quality Preoccupancy Purge brings in fresh
outdoor air before the Occupied mode begins. The IAQ PreOccupancy Purge is used to lower carbon dioxide levels below
the IAQ set point before Occupied mode starts.
The Purge is started two hours before the occupied time and
lasts for the specified duration.
Indoor Air Quality
Preoccupancy
Purge:
Range:
Disable/Enable
Default Value:
Disable
INDOOR AIR QUALITY PURGE DURATION — The
Indoor Air Quality Purge Duration specifies the duration of
IAQ Pre-Occupancy purge. The Purge is started two hours
before the occupied time and lasts for the specified duration.
Indoor Air Quality
Purge Duration:
Display Units:
Minutes
Display Range: 0 to 60
Default Value:
5
INDOOR AIR QUALITY DELTA SET POINT — The
Indoor Air Quality Delta Set Point specifies the highest
Indoor Air Quality level (measured in ppm) allowed within the
space whenever unit is in Occupied mode (or Supply Fan On
for units with Thermostat control) and Indoor Air Quality
sensor is installed.
Indoor Air Quality
Delta Set Point:
Display Units:
PPM (parts per
million)
Display Range: 1 to 5000
Default Value:
650
OUTDOOR AIR QUALITY LOCKOUT POINT (NOT
USED) — When set to non-zero value, the IAQ algorithm
will compare the Outdoor IAQ reading against this decision
and disable the IAQ control whenever the value of OAQ
exceeds this configured value.
Outdoor Air
Quality Lockout
Point:
Range:
0 to 5000
Default Value:
0
SERVICE PASSWORD — The Service Password function
defines the password needed to access the controller via the
Navigator interface.
Service Password: Range:
0000 to 9999
Default Value:
1111
PASSWORD ENABLE — The Password Enable function is
used to require a password when attempting to access the controller via the Navigator interface.
Password
Enable:
Range:
Enable/Disable
Default Value:
Disable
METRIC DISPLAY — The Metric Display function is used
to toggle the Navigator display between US and Metric units.
Metric Display: Range:
On/Off
Default Value:
Off
INDOOR AIR QUALITY MAXIMUM DAMPER POSITION — This point displays the upper limit of the Indoor Air
Quality minimum damper position calculated by the IAQ
control.
For example, IAQ is calculating 100% Minimum Damper
Position, but this decision is set to 50%, IAQ Minimum Damper Position will be clamped to 50%.
NOTE: When IAQ priority is set to HIGH, this value must
reflect the maximum outdoor air percent that the equipment
can heat or cool at worst conditions.
Indoor Air Quality
Maximum Damper
Position:
Display Units:
% Open
Display Range: 0 to 100
Default Value:
50
INDOOR AIR QUALITY SENSOR — The Indoor Air Quality sensor defines the value in parts per million (ppm) which
correlates to the low and high voltage readings from the sensor.
Low Reference specifies the Low Point of the Indoor IAQ
Sensor Range in ppm.
Low Reference: Units:
PPM (parts per million)
Range:
0 to 5000
Default Value:
0
Occupancy Maintenance Screen — The Occupancy Maintenance screen is used to check the occupied schedule.
Information concerning the current occupied period is displayed. See Table 14.
Table 14 — Occupancy Maintenance
DESCRIPTION
Mode
Current Occupied Period
Override in Progress
Override Duration
Occupied Start Time
Unoccupied Start Time
Next Occupied Day
Next Occupied Time
Next Unoccupied Day
Next Unoccupied Time
Last Unoccupied Day
Last Unoccupied Time
20
VALUE
0
0
No
0
00:00
00:00
00:00
00:00
00:00
UNITS
min
NAME
MODE
PERIOD
OVERLAST
OVERDURA
OCCSTART
UNSTART
NXTOCCD
NXTOCCT
NXTUNOD
NXTUNOT
PRVUNOD
PRVUNOT
NEXT OCCUPIED DAY — The Next Occupied Day point
displays the day of the week when the next occupied period
will begin. This point is used with the Next Occupied Time so
the user will know when the next occupied period will occur. If
the controller is following a global schedule this point will
remain at default.
Next Occupied
Day:
Display Range: MON, TUE, WED,
THU, FRI, SAT, SUN
Default Value:
No display (Blank)
Network Access: None
MODE — The Mode point displays the current occupied
mode for the controller. If the controller is following its own
local schedule this is the result of the local schedule status. If
the controller is configured to follow a global schedule, this
point displays the mode last received from a global schedule
broadcast.
Mode:
Display Range: 0 to 1
Default Value:
0
Network Access: None
CURRENT OCCUPIED PERIOD — If the controller is configured to determine occupancy locally, the Current Occupied
Period point is used to display the current period determining
occupancy.
Current Occupied
Period:
Display Range: 1 to 8
Default Value:
0
Network Access: None
OVERRIDE IN PROGRESS — The Override in Progress
point is used to display if an occupancy override is in progress.
The point will display “Yes” if an override is in progress, or
“No” if there is no override.
Override In
Progress:
Display Range: Yes/No
Default Value:
No
Network Access: None
NEXT OCCUPIED TIME — The Next Occupied Time point
displays the time of day when the next occupied period will
begin. This point is used with the Next Occupied Day so the
user will know when the next occupied period will occur. If the
PremierLink™ controller is following a global schedule this
point will remain at default.
Next Occupied
Time:
Display Range: 00:00 to 24:00
Default Value:
00:00
Network Access: None
NEXT UNOCCUPIED DAY — The Next Unoccupied Day
point displays the day of the week when the next unoccupied
period will begin. This point is used with the Next Unoccupied
Time so the user will know when the next unoccupied period
will occur. If the controller is following a global schedule this
point will remain at default.
Next Unoccupied
Day:
Display Range: MON, TUE, WED,
THU, FRI, SAT, SUN
Default Value:
No display (Blank)
Network Access: None
NEXT UNOCCUPIED TIME — The Next Unoccupied Time
point displays the time of day when the next unoccupied
period will begin. This point is used with the Next Unoccupied
Day so the user will know when the next unoccupied period
will occur. If the controller is following a global schedule this
point will remain at default.
Next Unoccupied
Time:
Display Range: 00:00 to 24:00
Default Value:
00:00
Network Access: None
OVERRIDE DURATION — The Override Duration point
displays the number of minutes remaining for an occupancy
override that is in effect. If the override duration value downloaded is in hours, the value will be converted to minutes. If the
occupancy schedule is occupied when override is initiated, the
current occupancy period will be extended by the number of
hours/minutes requested.
If the current occupancy period is unoccupied when the occupancy override is initiated, the mode will change to occupied
for the duration of hours/minutes downloaded. If the occupancy override is due to end after the start of the next occupancy
period, the mode will transition from occupancy override to occupied without becoming unoccupied, and the occupancy override timer will be reset.
Override
Duration:
Display Units:
Minutes
Display Range: 0 to 240
Default Value:
0
Network Access: None
OCCUPIED START TIME — The Occupied Start Time
point shows the time that the current occupied mode began. If
the current mode is unoccupied or the controller is following a
global schedule, the value displayed by this point will remain at
default.
Occupied
Start Time:
Display Range: 00:00 to 24:00
Default Value:
00:00
Network Access: None
LAST UNOCCUPIED DAY — The Last Unoccupied Day
point displays the day of the week when the controller last
changed from occupied to the Unoccupied mode. This point is
used in conjunction with the Last Unoccupied Time to know
the last time and day when the controller became unoccupied.
If the controller is following a global schedule this point will
remain at default.
Last Unoccupied
Day:
Display Range: MON, TUE, WED,
THU, FRI, SAT, SUN
Default Value:
No display (Blank)
Network Access: None
UNOCCUPIED START TIME — The Unoccupied Start Time
point shows the time that the current occupied mode will end.
This will also be the beginning of the next unoccupied mode. If
the current mode is unoccupied or the controller is following a
global schedule, the value displayed by this point will remain at
default.
Unoccupied
Start Time:
Display Range: 00:00 to 24:00
Default Value:
00:00
Network Access: None
LAST UNOCCUPIED TIME — The Last Unoccupied Time
point displays the time of day when the controller last changed
from occupied to the Unoccupied mode. This point is read in
conjunction with the Last Unoccupied Day to know the last
time and day when the controller became unoccupied. If the
controller is following a global schedule this point will remain
at default.
Last Unoccupied
Time
Display Range: 00:00 to 24:00
Default Value:
00:00
Network Access: None
21
Maintenance Screen — The Maintenance Screen is
TEMP COMPENSATED START — Indicates that the controller has started the equipment prior to occupancy in order to
be at the occupied set points at the start of occupancy.
Temp
Compensated
Start:
Display Range:
No/Yes
Default Value:
No
Network Access:
Read Only
used to service the PremierLink™ controller. See Table 15.
THERMOSTAT CONTROL — Indicates the result of the
configuration decision to control in the thermostat or sensor
mode.
Thermostat
Control:
Display Range:
No/Yes
Default Value:
Yes
Network Access:
Read Only
IAQ PRE-OCCUPANCY PURGE — Indicates that the preoccupancy purge mode is currently active.
IAQ
Pre-occupancy
Purge:
Display Range:
No/Yes
Default Value:
No
Network Access:
Read Only
OCCUPIED — The Occupied point indicates whether or not
the controller is operating in the Occupied mode.
Occupied:
Display Range:
No/Yes
Default Value:
No
Network Access:
Read/Write
TIMED OVERRIDE IN EFFECT — The Timed Override In
Effect point shows if a timed override is currently in effect.
Timed Override
in Effect:
Display Range:
No/Yes
Default Value:
No
Network Access:
Read Only
UNOCCUPIED FREE COOLING — Indicates that unoccupied free cooling is in effect.
Unoccupied Free
Cooling:
Display Range:
No/Yes
Default Value:
No
Network Access:
Read Only
START BIAS TIME — The Start Bias Time, in minutes, is
calculated by the controller during the unoccupied period (as
needed) to bring the temperature up or down to the set point
under the optimum start routine. The start time bias for heat
and cool are configurable. This value will be reported to the
Linkage Thermostat if it is used. It cannot be used with Global
Scheduling.
Start Bias Time: Display Units:
Minutes
Display Range:
0 to 180
Default Value:
0
Network Access:
Read Only
FIRE SHUTDOWN — Indicates (in a sensor mode) that the
Fire shutdown input has been sensed. This will also cause the
supply fan and heating and cooling to be turned off.
Fire Shutdown: Display Range:
No/Yes
Default Value:
No
Network Access:
Read/Write
LINKAGE CONTROL — Indicates if the controller is receiving linkage communication.
Linkage Control: Display Range:
No/Yes
Default Value:
No
Network Access:
Read/Write
HEAT — The Heat point shows if there is a demand for heat in
the space. The space temperature must be below the Occupied
Low or Unoccupied Low set point.
NOTE: When a control mode ends, “NO” mode must be completed before opposite mode can begin.
Heat:
Display Range:
No/Yes
Default Value:
No
Network Access:
None
FIELD/STARTUP TEST — This point is used to enable a
controller field test. When forced to Yes, the controller will perform a test of all outputs and reset to “NO” at end of test. The
test may be aborted at any time by forcing value to NO.
Field/Startup
Test:
Display Range:
No/Yes
Default Value:
No
Network Access:
Read/Write
HEAT SUBMASTER REFERENCE — When in sensor
mode, the Heat Submaster Reference point displays the supply
air temperature calculated by the heating PID loop. This value
is compared to the actual supply air temperature to determine
the number of required stages. When in the thermostat mode,
the value displayed is zero.
Heat Submaster
Reference:
Display Units:
Degrees F (Degrees C)
Display Range: 40.0 to 150.0
Default Value:
40
Network Access: Read Only
COOL — The Cool point shows if there is a demand for cooling in the space. The space temperature must be above the
Occupied High or Unoccupied High set point.
NOTE: When a control mode ends, “NO” mode must be completed before opposite mode can begin.
Cool:
Display Range:
No/Yes
Default Value:
No
Network Access:
None
IAQ CONTROL — Indicates weather or not IAQ control is
active in the controller. IAQ control of the minimum damper
position is active whenever the configured parameters for the
IAQ PID calculate a minimum position greater than the configured economizer minimum position.
IAQ Control:
Display Range: No/Yes
Default Value:
No
Network Access: Read Only
COOL SUBMASTER REFERENCE — The Cool Submaster Reference point displays the supply air temperature calculated by the cooling PID loop when in sensor mode. This value
is compared to the actual supply air temperature to determine
the number of required stages. When in the thermostat mode,
the value displayed is zero.
Cool Submaster
Reference:
Display Units:
Degrees F (Degrees C)
Display Range: 40.0 to 150.0
Default Value:
150
Network Access: Read Only
DEMAND LIMIT — Indicates that a command has been
received to limit capacity or reduce capacity of the heating or
cooling.
Demand Limit: Display Range: No/Yes
Default Value:
No
Network Access: Read Only
22
The Supervisory Block displays the block or table
number of the linkage table occurrence in the supervisory
device. Some linkage supervisory devices may contain
more than one linkage table for different air sources.
Supervisory
Block:
Default Value:
0
Network Access: Read Only
The Average Occupied Heat Set Point displays the
Occupied Heat set point from the Linkage Thermostat.
Average Occupied
Heat Set Point: Display Units:
Degrees F (Degrees C)
Display Range: 0.0 to 99.9
Default Value:
0.0
Network Access: None
The Average Occupied Cool Set Point displays the Occupied Cool set point from the Linkage Thermostat.
Average Occupied
Cool Set Point: Display Units:
Degrees F (Degrees C)
Display Range: 0.0 to 99.9
Default Value:
0.0
Network Access: None
The Average Unoccupied Heat Set Point displays the Unoccupied heat set point from the Linkage Thermostat.
Average Unoccupied
Heat Set Point: Display Units:
Degrees F (Degrees C)
Display Range: 0.0 to 99.9
Default Value:
0.0
Network Access: None
The Average Unoccupied Cool Set Point displays the Unoccupied cool set point from the Linkage Thermostat.
Average Unoccupied
Cool Set Point: Display Units:
Degrees F (Degrees C)
Display Range: 0.0 to 99.9
Default Value:
0.0
Network Access: None
The Average Zone Temperature displays the space temperature from the Linkage Thermostat.
Average Zone
Temperature:
Display Units:
Degrees F (Degrees C)
Display Range: 0.0 to 99.9
Default Value:
0.0
Network Access: None
The Average Occupied Zone Temperature displays the
space temperature from the Linkage Thermostat during occupied periods.
Average Occupied
Zone Temperature: Display Units:
Degrees F (Degrees C)
Display Range: 0.0 to 99.9
Default Value:
0.0
Network Access: None
The Occupancy Status point displays a 1 if occupancy is reported by the Linkage Thermostat. The Occupancy Status
point displays a 0 if occupancy is not reported by the Linkage
Thermostat.
Occupancy
Status:
Display Range: 0, 1
Default Value:
0
Network Access: None
ECONOMIZER SUBMASTER REFERENCE (NOT
USED) — This point displays the supply air temperature determined by the Economizer PID calculation.
Economizer
Submaster
Reference:
Display Units:
Degrees F (Degrees C)
Display Range:
48 to 120
Default Value:
120
Network Access: Read Only
ECONOMIZER SUBMASTER GAIN (NOT USED) —
Displays the current Submaster gain multiplier in use to calculate the economizer damper position. At temperatures below
45 F this number will decrease to slow the rate of movement of
the economizer damper.
Economizer
Submaster Gain: Display Range: –20 to 20
Default Value:
–5.5
Network Access: Read Only
COMPRESSOR STARTS — Displays the total number of
compressor starts.
Compressor
Starts:
Default Value:
0
Network Access: Read Only
COMPRESSOR 1 RUN TIME — Displays the number of
run hours of compressor no. 1.
Compressor 1
Run Time:
Display Units:
Hours
Default Value:
0
Network Access: Read Only
COMPRESSOR 2 RUN TIME — Displays the number of
run hours of compressor 2.
Compressor 2
Run Time:
Display Units:
Hours
Default Value:
0
Network Access: Read Only
SUPPLY FAN RUN TIME — Displays the number of supply
fan run hours. This is not the same timer used for the filter status. A separate timer is used to keep track of the run hours since
the last filter change.
Supply Fan
Run Time:
Display Units:
Hours
Default Value:
0
Network Access: Read Only
LINKAGE THERMOSTAT — The following Linkage Thermostat points display the standard values received from a
Linkage Thermostat (if one is being used to provide space
temperature, set point and occupancy information).
Linkage
Status:
Display Range: 0 to 3
Default Value:
2
Network Access: None
The Supervisory Element displays the address of the device
sending the linkage supervisory table to the PremierLink™
controller.
Supervisory
Element:
Default Value:
0
Network Access: Read Only
The Supervisory Bus displays the bus number of the device
sending the linkage supervisory table to the PremierLink
controller.
Supervisory Bus: Default Value:
0
Network Access: Read Only
23
Table 15 — Maintenance
DESCRIPTION
Thermostat Control
Occupied
Timed Override in Effect
Start Bias Time
Heat
Cool
IAQ Control
Demand Limit
Temp Compensated Start
IAQ Pre-Occupancy Purge
Unoccupied Free Cool
Fire Shutdown
Linkage Control
Field/Startup Test
Heat Submaster Ref
Cool Submaster Ref
Economizer Submaster Ref
Economizer Submastr Gain
Compressor Starts
Compressor 1 Runtime
Compressor 2 Runtime
Supply Fan Runtime
Linkage Thermostat
Linkage Status
Supervisory Element
Supervisory Bus
Supervisory Block
Average Occ Heat Setpt
Average Occ Cool Setpt
Average Unoc Heat Setpt
Average Unoc Cool Setpt
Average Zone Temp
Average Occ Zone Temp
Occupancy Status (1=occ)
VALUE
UNITS
No
Yes
No
0
No
No
No
No
No
No
No
No
No
No
40.0
150.0
120.0
0.00
0.00
0.00
0.00
17.00
2
0
0
0
0.0
0.0
0.0
0.0
0.0
0.0
1
min
dF
dF
dF
HOURS
HOURS
HOURS
dF
dF
dF
dF
dF
dF
STATUS
FORCE
NAME
TSTAT
OCCUP
TIMOV
STRTBIAS
HEAT
COOL
IAQCL
DEMLT
TCSTR
IQPRG
NTFCL
FIRES
DAVCL
FIELD
SHSR
CCSR
ECONSR
ECONGN
CMPST
CM1RT
CM2RT
FANRT
LINKSTAT
SUPE-ADR
SUPE-BUS
BLOCKNUM
OCLOSTPT
OCHISTPT
UNLOSTPT
UNHISTPT
AZT
AOZT
OCCSTAT
NOTE: Bold values indicate points that can be forced through communications.
Copyright 2002 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
PC 111
Catalog No. 535-00091
Printed in U.S.A.
Form 50-9SI
Pg 24
11-02
Replaces: New
Book 1 4
Tab 5a 5a