Siemens 600Series Instruction manual

g1613.cvr Page 1 Thursday, October 8, 1998 11:22 AM
Quick Reference Guide
ROLMphone 300/600 Series
for 9006i and Hicom 300 E CS
Creating a World of Highly Integrated
Communications & Solutions
NOTE: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used
in accordance with the instruction manual, may cause harmful interference to
radio communication. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to take
whatever measures may be required to correct the interference at his or her own
expense.
WARNING: Changes or modifications to the equipment that are not expressly
approved by the responsible party for compliance could void the user’s
authority ot operate the equipment.
This equipment does not exceed Class A limits per radio noise emissions for
digital apparatus, set out in the Radio Interference Regulation of the Canadian
Department of Communications. Operation in a residential area may cause
unacceptable interference to radio and TV reception requiring the owner or
operator to take whatever steps are necessary to correct the interference.
Cet équipement ne dépasse pas les limites de Classe A d'émission de bruits
radioélectriques por les appareils numériques, telles que prescrites par le
Règlement sur le brouillage radioélectrique établi par le ministère des Communications du Canada. L'exploitation faite en milieu résidentiel peut entraîner le
brouillage des réceptions radio et télé, ce qui obligerait le propriétaire ou
l'opérateur à prendre les dispositions nécessaires pour en éliminer les causes.
November 1998
Form No. GU30-1613-01
Part No. 06E0108
EC No. A93070
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical, electronic, photocopying, recording, or otherwise, without prior written permission of Siemens Business Communication System, Inc.
Request Siemens publications from your Siemens representative or the Siemens branch serving you. Publications are not stocked at the address below.
Siemens Business Communication Systems, Inc.
4900 Old Ironsides Drive
P.O. Box 58075
Santa Clara, CA 95052-8075
(408) 492-2000
TWX: 9103387350 ROLM SNTA B Telex: 278156 ROLM UR
ROLMphone and PhoneMail are registered trademarks and ROLMfax is a
trademark of Siemens Business Communication Systems, Inc.
Siemens and Hicom are registered trademarks of Siemens Aktiengesellschaft.
Copyright Siemens Business Communication Systems, Inc. 1995, 1996, 1997,
1998.
All rights reserved.
Contents
Welcome to Your ROLMphone Telephone . . . . . . . . . . . . . . 1
Where to Go for Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Your Class of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Line Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Feature Keys and Access Codes . . . . . . . . . . . . . . . . . . . . . . . 3
Callback Request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Consultation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Last Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Open Listening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pick A Call and Add to Conference . . . . . . . . . . . . . . . . . . . 15
Preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Repertory Dialing (Repdial)
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Saved Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Speakerphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Station Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Station Speed (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
System Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Feature Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
i
ii
Welcome to Your ROLMphone
Telephone
The ROLMphone 300/600 series of multi-featured phones
have many options that enhance their functionality. Your
ROLMphone model may have a display, a speakerphone, from
12 to 40 feature keys, and multiple extensions.
These digital telephones work with your company’s Siemens
Communications Server to give you advanced, easy-to-use
telephone features. The Siemens Communications Server is
your facility’s internal telecommunications system.
Display
Headset
Feature Keys
Speaker
Dial Pad
Volume Keys
Line Key
ROLMphone 312L Telephone
The ROLMphone 600 series telephones are modular and allow
you to install the Data Communications Option (DCO),
Headset/Recorder Option (HRO), Electret Headset Option
(EHO), Analog Adapter Option (AAO), CTI/Headset Combo,
or the Keyboard Expansion Option (KEO). You can install the
KEO and any two of the other modules in the phone at one time.
ROLMphone 300 series telephones are non-modular and do not
support these options.
1
Where to Go for Assistance
Although every company has its own way of handling support
for ROLMphone telephones, most have a person responsible for
making configuration changes and answering questions about
the telephone system. This person, the system administrator,
can provide you with information on the features you need to
use and can help troubleshoot problems with your phone when
necessary. For more detailed information about your phone’s
features and operation, refer to the ROLMphone 300/600 Series
User Guide for 9751 CBX and Hicom 300 E CS
(GU30-1614).
Your Class of Service
Each phone in your system has a class of service (COS) that
specifies the features available to it. Therefore, you may find
that some features included in this guide are not available on
your telephone. Ask your system administrator which features
have been assigned to your telephone.
Display
The display at the top of the ROLMphone L models (RP312L,
RP612L, RP612SL, RP624L, and RP624SL) provides call
information such as the extension calling you and, if your
system is configured to do so, the caller’s name. It also lets you
scroll through messages waiting in your mailbox and provides
information you’ll find useful as you set up and use Siemens
features.
2
Line Keys
Your ROLMphone telephone has a separate line key for every
extension that appears on your phone. You use the line keys to
answer and place calls.
Status Lights
The red status lights next to the line keys tell you what is
happening on those lines. A line key status light may turn on
steadily, blink, or flash at different rates to signal the status of
that line.
Table 1. Line Key Status Light Flash Rates
Flash Rate
Line Status
Off
Available
On steady
In use
Blinking
Ringing
Flashing (faster)
On hold
Flickering (fastest)
Forwarded
Feature Keys and Access Codes
You can press feature keys to gain access to system features
such as Hold, Transfer, Mailbox, and Program. Since your
phone has already been assigned a set of feature keys, it may not
have some of the feature keys described here. However, you
may still use any feature available on your system and permitted
by your class of service by dialing its feature access code, if it
has one. This guide explains the basic steps for using many
features, including the default feature access codes (which your
system administrator may have configured differently).
3
Sounds
Your phone makes different sounds to let you know what’s
going on; rings occur on a line that you are not using to indicate
that you have an incoming call, tones occur while you are using
your phone and provide information about calls and features.
Table 2. Rings
Sound
Meaning
Single (repeated)
,QWHUQDO RU (PHUJHQF\
FDOO
'RXEOH UHSHDWHG
([WHUQDO FDOO
7ULSOH UHSHDWHG
&DOOEDFN
Table 3. Tones
Sound
Meaning
%XV\ WRQH
7KH SDUW\ \RX FDOOHG LV
RQ WKH SKRQH
'LDO WRQH
<RX FDQ PDNH D FDOO RU
LQYRNH D IHDWXUH
)DVW EXV\ WRQH
,QYDOLG FDOO
6KRUW WRQH HYHU\ ,QWHUQDO FDOO ZDLWLQJ
VHFV
VKRUW WRQHV FRQILU
$ IHDWXUH KDV EHHQ VXF
PDWLRQ WRQH
FHVVIXOO\ DFWLYDWHG
VKRUW WRQHV IROORZHG
$GGLWLRQDO LQSXW VXFK
E\ GLDO WRQH
DV D 3,1 LV UHTXLUHG
VKRUW WRQHV HYHU\ ([WHUQDO FDOO ZDLWLQJ
VHFV
:DYHULQJ HUURU WRQH
4
,QYDOLG IHDWXUH UHTXHVW
Callback Request
Callback Request has the communications server help you
complete calls to extensions that are busy, ringing, or in Do Not
Disturb mode. It lets you hang up and have the communications
server call you back with triple rings. When you then answer,
the communications server automatically dials the number.
To request a callback,
1.
2.
Listen for the phone to ring or for the busy signal.
CALL
BCK
Press the Callback (CALLBCK) key, or dial # 1.
3.
Listen for the confirmation tone. If you have a
display phone, WILL CALL BACK is displayed.
4.
Hang up.
5.
When the communications server calls back with
triple rings, answer and the communications server
will dial the extension.
5
Conference
The Conference feature lets you have up to eight parties,
including yourself, in a telephone conversation. The other
parties besides yourself can be on trunks (outside lines) or
extensions.
To set up a conference,
1.
TRANSFR
During a call, press the Transfer (TRANSFR) key
to put the party on consultation hold.
2.
Listen for the confirmation tone, followed by the
internal dial tone.
3.
Dial the extension you want to add, or dial 9 and
the outside number.
4.
CONF
After the party answers, press the Conference
(CONF) key (or TRANSFR) to join all the parties.
To reconnect to the conference when a called party
isn’t joining,
CONNECT
Press the Connect key.
To drop the last added party,
1.
CLEAR
Press the Clear key, or press TRANSFR and dial
∗ ∗ ∗ 4.
2.
CONF
Press the Conference (CONF) key (or TRANSFR)
to rejoin the conference.
6
Connect
Connect lets you
• reconnect with a call placed on consultation hold
• reconnect with a transferred call before the transfer is complete
• alternate between two parties, when you have one of them
on consultation hold
To reconnect with a call,
CONNECT
Press the Connect key.
Consultation
Consultation lets you put the other party in a call on
consultation hold, so that you can call and talk privately with a
second party. You can then press the Connect key to alternate
between the two parties.
To consult with a second party during a call,
1.
TRANSFR
Press the Transfer (TRANSFR) key to put the first
party on consultation hold.
2.
Listen for the confirmation tone, followed by the
internal dial tone. The Connect key status light
flashes.
3.
Dial the second party’s extension or 9 and the
outside number.
4.
Talk with the second party.
To reconnect with the first party,
CONNECT
Press the Connect key. You can continue to use the
Connect key to alternate between the two parties.
7
Forwarding
Forwarding redirects your incoming calls to another extension
or an outside number. Variable Forwarding lets you set up an
extension or outside number for forwarding under conditions
you specify. Fixed Forwarding sends calls to extensions set up
for you at the communications server.
To use Variable Forwarding for all calls under all
conditions,
1.
FORWARD
Get a dial tone, and press the Forward key or dial
# 9 1.
2.
Dial the extension or 9 and the outside number you
want to receive your calls.
3.
Hang up.
To cancel Variable Forwarding,
FORWARD
Press the Forward key, or get a dial tone and dial #
# 9 1.
To cancel Fixed Forwarding,
Get a dial tone and dial # # 9 0.
To restore Fixed Forwarding,
Get a dial tone and dial # 9 0.
8
Hold
The Hold key lets you temporarily hang up a line without
disconnecting the other party. If you do not retrieve the call after
a certain period of time (determined by the communications
server), your phone will ring. If it is an external call and you do
not answer, the call is transferred to the operator.
If you want to make another call after placing a call on hold, you
must use another line. If your telephone has only one line, press
the Transfer key, instead of the Hold key, to place the call on
consultation hold, then dial the second party.
To put a call on hold,
1.
2.
HOLD
Press the Hold key.
Hang up.
To reconnect,
Press the line key next to the flashing status light,
or pick up the handset and press the line key.
9
Last Number Redial
On communications server Version 6.4 and higher, this feature
lets you quickly redial the last number you have dialed. Each
time you dial a valid internal or external telephone number it is
automatically stored so that you can redial it later. Numbers
dialed during consultation calls and transfers are also stored.
Only one number is stored at a time, and once you dial a new
number it replaces the number stored previously.
To redial the last number dialed,
LNR
10
Press the Last Number Redial (LNR) key. Or get a
dial tone and dial # # 4.
Mailbox
This feature lets you receive and answer reminder messages and
PhoneMail and ROLMfax  notifications. Messages and
notifications turn on the status light beside your Mailbox key
and (on display phones) provide information about the call. The
Mailbox key also lets you leave reminder messages at other
extensions.
To display messages and notifications,
MAILBOX
Press the Mailbox key. Press the Mailbox key
again to scroll through multiple messages or
notifications. If you want to clear the message or
notification, press the Clear key.
To answer a displayed message or notification,
CALL
BCK
Press the Callback (CALLBCK) key.
To answer a message or notification on a nondisplay phone,
MAILBOX
Press the Mailbox key. (Press the PHMAIL key if
your phone has one. Its status light turns on to
indicate PhoneMail messages.)
To leave a reminder message,
MAILBOX
After receiving a busy or ringing signal, press the
Mailbox key or dial # ∗ 1.
11
Open Listening
Open Listening allows you to use your handset and, at the same
time, let someone nearby listen to the conversation over the
speaker. While Open Listening is active, someone nearby can
hear your conversation, but his or her voice will not be picked
up by the telephone’s microphone.
To use Open Listening during a handset call,
SPEAKER
During your conversation over the handset, press
the Speaker key.
To use Open Listening during a speakerphone call,
1.
2.
During your conversation, pick up the handset.
SPEAKER
Press the Speaker key.
To cancel Open Listening,
SPEAKER
12
Press the Speaker key again.
Park
Park lets you move a call to an extension and hold it there
without ringing that extension. You or another party can then
retrieve the call from the extension as needed.
To park a call to another extension,
1.
TRANSFR
Press the Transfer (TRANSFR) key.
2.
Dial ∗ 6.
3.
Dial the extension where you want to
park the call.
4.
Hang up.
To retrieve a parked call,
1.
Get a dial tone.
2.
Dial ∗ 6.
3.
Dial the extension where the call is
parked.
4.
Begin speaking.
13
Pickup
Pickup features let you answer calls ringing, on hold, queued, or
parked at other extensions.
Group Pickup lets you answer a call to an extension in your
pickup group (set up at the communications server) even when
you do not know the number for the extension.
Station Pickup lets you answer a call at any extension, provided
that you know the number for the extension.
To answer a call in your pickup group,
PICKUP
PICKUP
Press the Pickup key twice. Or get a dial
tone and dial ∗ ∗ 3.
To answer a call ringing, on hold, queued, or
parked at any extension,
1.
2.
14
PICKUP
Press the Pickup key, or get a dial tone and dial
∗ 3.
Dial the extension.
Pick A Call and Add to Conference
You can use the Pickup feature to pick up the following kinds
of calls and add them to a conference call.
• a call alerting or ringing on another extension, on your
phone or other phones
• a call on hold on another line, on your phone or another
phone
• a call parked on another extension
• a call on busy standby queuing for another extension
• a call on busy standby queuing for the line that you are using
To pick a call and add it to a conference
1.
PICKUP
2.
Press the Pickup key during a two-party call or a
conference call. Or get a dial tone and dial ∗ 3. The
other call is placed on consultation hold.
Dial the extension where the call to be picked up is
located.
If the call you are picking up is on busy standby
queuing for your line, you will already be
connected to it now. You do not have to dial an
extension for it.
3.
CONF
After the picked up party answers, press the
Conference (CONF) key to join all the parties.
If the picked up party does not want to join the
conference, press the Clear key. This disconnects
the picked up party and returns you to the original
call.
To go back and forth (toggle) between the picked
up party and the original call, press the Connect
key.
Note: You can also transfer, place on hold, place on
consultation hold, or park a call you have picked up. (See
“Transfer” on page 24, “Hold” on page 9, “Consultation” on
page 7, and “Park” on page 13.) To screen an incoming call
before picking it up, put the conference on hold and answer the
call. Then return to the conference and pick up the call.
15
Preview
The Preview feature lets you view information associated with
any line configured on your phone. You can see the following
information when the phone is idle or active on a call:
•
the identity of the caller on a line configured to ring on your
phone (including recalling lines from hold, park, system
hold, and transfer.)
•
the identity of the caller for the line you are currently using.
•
the identity of a party or a camped-on party on your
currently active line.
•
the information about a line on hold.
To activate the Preview feature,
1. Press the Preview key. The Preview status light turns on.
2. Press a line key to view information.
Line information is displayed for 8 seconds. If you take no
further action, the display reverts to the previous content. The
Preview key remains active so that you can continue to
display information about other lines.
To deactivate the Preview feature,
You can do one of the following:
• Press the Preview key. The status light turns off.
• Press any key except the following dial pad keys: Mute,
Volume, Time, 0 through 9, *, or #.
• Make a call using the speakerphone.
• Place the handset on-hook if it is off-hook.
• Place the handset off-hook if it is on-hook.
To answer a call on a Preview line,
If your phone is idle, go off-hook and begin speaking while
the preview information is displayed.
If you are active on a call, turn the Preview key off before
answering the call.
16
Repertory Dialing (Repdial)
Keys
This feature lets you set up each repdial (R-) key on your
faceplate for one-touch dialing of an extension, outside number,
feature access code, or combination of numbers and feature
access codes.
To set up a repdial key,
1.
2.
PROGRAM
R-
Press the repdial (R-) key that you want to use.
Enter the dialing sequence you want to assign to
the key.
3.
4.
Press the Program key.
PROGRAM
Press the Program key. On your faceplate, label the
key with the name of the feature or person that it
dials.
To dial using a repdial key,
R-
Press the repdial (R-) key.
17
Saved Number Redial
This feature saves a number that you have dialed. Later, you can
redial your saved number by pressing the Saved Number Redial
(SAV/RDL) key.
To save a number you have dialed,
SAV/RDL
Press the Saved Number Redial (SAV/RDL) key,
or dial # 4 while the call is still ringing or busy.
To dial your saved number,
SAV/RDL
18
Press the Saved Number Redial (SAV/RDL) key,
or get a dial tone and dial # 4.
Speaker
All ROLMphone 300/600 series phones have a speaker that you
can use for receiving calls or listening to the PhoneMail
system. On ROLMphone models that only have a speaker and
not a microphone, you must pick up your handset to speak to the
other party.
To answer a call,
Pick up the handset. The blinking status light next
to the line key turns on steadily.
To hang up,
Hang up the handset.
Speakerphone
The ROLMphone 600 series S models (RP612S, RP612SL,
RP624S, and RP624SL) have a two-way speakerphone,
consisting of a speaker and a microphone. You can use the
speakerphone to make or answer calls without picking up the
handset.
To make a call,
Press a line key or the Speaker key to get a dial
tone, then dial.
To answer a call,
Press the line key next to the blinking status light.
To hang up,
Press the line key or the Speaker key.
To switch during a call,
SPEAKER
If you are using the handset and want to use the
speakerphone, press the Speaker key and hang up
the handset. If you are using the speakerphone and
want to use the handset, pick up the handset.
19
Station Speed Dialing
Station Speed Dialing lets you assign frequently used dialing
sequences (extensions, outside numbers, or feature access
codes) to each of ten single-digit codes (0 through 9). You can
then dial a single-digit code instead of the entire sequence. On
Version 6.3 and higher, you can also be set up at the
communications server for up to 30 codes, in groups of 10. If
you are set up for more than ten, they follow a double-digit
scheme (00 through 29).
To set up a station speed code on a display phone,
1.
PROGRAM
Press the Program key.
2.
SPEED
Press the Station Speed (SPEED) key, or dial # # 3.
3.
Enter the station speed code.
4.
After NEW NUMBER? is displayed, enter the
dialing sequence.
5.
PROGRAM
Press the Program key.
To set up a station speed code on a non-display
phone,
1.
SPEED
SPEED
Press the Station Speed (SPEED) key
twice, or get a dial tone and dial # # 3.
2.
Enter the station speed code.
3.
Enter the dialing sequence. Then hang
up.
20
Station Speed (continued)
To dial using a station speed code,
1.
SPEED
Press the Station Speed (SPEED) key.
2.
Listen for the confirmation tone.
3.
Dial the station speed code.
OR
1.
Get a dial tone.
2.
Dial # 3 and then the station speed code.
21
System Hold
System Hold lets you move a call to a system slot (a temporary
holding place) and hold it there. The call can then be retrieved
from any extension.
To place a call on system hold on a display phone,
SYS
HOLD
Press the System Hold (SYSHOLD) key, and the
communications server will assign the call to a slot
and display the number of the slot. Then hang up.
To place a call on system hold on a non-display
phone,
1.
TRANSFR
Press the Transfer (TRANSFR) key. You will hear
the confirmation tone and dial tone. Dial ∗ 8.
Enter a slot number (0-9). If you hear a busy signal,
try a different slot number. If all slots are full, you
will hear a fast busy signal. Then hang up.
2.
To retrieve a call on system hold,
1.
2.
3.
22
Get a dial tone.
SYS
HOLD
Press the System Hold (SYSHOLD) key, or dial
∗ 8.
Dial the number of the system slot where the call is
on system hold.
System Speed Dialing
If the System Speed Dialing feature is set up on your
communications server, you can dial frequently called outside
numbers (local, long distance, and international) by dialing a
code number. Usually these codes are published for an entire
company in a special system speed directory. Consult your
system administrator if you do not know your system speed
numbers. Your company may have up to sixteen system speed
lists. You may have access to two of these lists. For release 6.4
and above, you may have access to two of these lists or to the
first ten lists plus one additional list. A number set up for a
system speed code can contain an initial Personal Identification
Number (PIN), if one is necessary to make outside calls.
To make a system speed call,
1.
2.
SYS-SP1
Press the correct System Speed key (SYS-SP1 for
the first System Speed list or SYS-SP2 for the
second). Or, get a dial tone and dial # 6 1 for the
first list or # 6 2 for the second.
Dial the system speed code.
23
Transfer
Transfer lets you move a call to another extension or to an
outside number if your communications server is set up to do
this.
To transfer a call,
1.
2.
Ask the other party to hold.
TRANSFR
Press the Transfer (TRANSFR) key.
3.
Dial the extension, or dial 9 and the outside
number.
4.
If you want, announce the caller when the party
answers.
5.
Hang up.
To reconnect,
CONNECT
Before hanging up, press the Connect key to rejoin
the original call.
24
Feature Access Codes
To use feature access codes
➩ Get a dial tone, or press the Transfer key during a call. Dial the
feature access code. You may need to press the Connect key to
return to your call.
Feature
Access Code
Account Number
Bad Line Reporting
∗2
∗563
Busy Override
Buzz
##7
#∗2
Callback Request
Cancel
#1
##1
Changing Ring Tone
Class of Service
∗572
Restore Primary
Return to Secondary
Com Group Speaker Call
Conference
Remove Last Party
Remove Specific Party
∗#591
∗#590
∗∗6
∗∗∗4
∗ ∗ 4 1-8
Direct Trunk Select
Forwarding, Fixed
##8
#90
Cancel
Forwarding, Variable
##90
All
Busy
#91
#94
Busy/Ring No Answer
External
#95
#92
Internal
Ring No Answer
#93
#96
Cancel
Last Number Redial
##91
##4
Mailbox Callback Message
Leave Message
#∗1
Cancel
Turn Off Light
Park
Pickup
Group
Station
#∗8
∗52
∗6
∗∗3
∗3
PIN Authorization
Cancel
∗#57
∗#58
Privacy
Cancel
#2
##2
Saved Number Redial
Speaker Call, Fixed
#4
#∗4
Speaker Call, One-Way
Speaker Call, One-Way Broadcast
#81
#80
Station Hunt
Prevent
#∗93
Allow
Set Destination
Clear Destination
Station Speed Dialing
Set Up
Call
#∗92
#∗90
#∗99
##3
#3
System Hold
System Speed-1
∗ 8 0-9
#61
System Speed-2
Trace
#62
###1
Universal Night Answer
∗#3
25
26