Yamaha HTR-6050 Owner`s manual

U
HTR-6050
AV Receiver
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
overturn.
Caution-i En
11
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
Important safety instructions
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
Caution-ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Caution: Read this before operating your unit.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in a environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
Caution-iii En
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set this unit
in the standby mode, and disconnect the AC power plug from
the wall outlet.
19 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
20 Excessive sound pressure from earphones and headphones can
cause hearing loss.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off by STANDBY/ON. This
state is called the standby mode. In this state, this unit
is designed to consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
Contents
Features ................................................................... 2
Getting started ........................................................ 3
Quick start guide .................................................... 4
PREPARATION
Connections ........................................................... 10
Using SET MENU................................................... 47
1 SOUND MENU.................................................... 48
2 INPUT MENU...................................................... 52
3 OPTION MENU................................................... 54
Remote control features........................................56
Using remote control on the SCENE feature........... 56
Controlling this unit, a TV, or other components........ 57
Setting remote control codes ................................... 59
Advanced setup......................................................60
ADDITIONAL INFORMATION
Troubleshooting.....................................................61
Glossary..................................................................68
Specifications .........................................................70
Index .......................................................................71
APPENDIX
(at the end of this manual)
Using AUTO SETUP .............................................. 24
Selecting the desired SCENE template.................... 28
Creating your original SCENE templates................ 31
Playback ................................................................ 32
Basic operations....................................................... 32
Additional operations............................................... 33
Sound field programs ........................................... 37
Sound field program descriptions............................ 37
FM/AM tuning ...................................................... 40
Using a USB memory device or
a USB portable audio player ........................... 43
Playback operation................................................... 43
Recording .............................................................. 45
APPENDIX
Automatic tuning ..................................................... 40
Manual tuning.......................................................... 40
Automatic preset tuning........................................... 41
Manual preset tuning ............................................... 41
Selecting preset stations........................................... 42
Exchanging preset station ........................................ 42
About this manual
• y indicates a tip for your operation.
• Some operations can be performed by using either the
buttons on the front panel or the ones on the remote control.
In case the button names differ between the front panel and
the remote control, the button name on the remote control is
given in parentheses.
• This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the
manual and product, the product has priority.
• “9 SPEAKERS” or “A MULTI CH IN” (example)
indicates the name of the parts on the front panel or the
remote control. Refer to the attached sheet or the appendix
pages at the end of this manual for the information about
each position of the parts.
• The symbol “☞ ” with page number(s) indicates the
corresponding reference page(s).
ADDITIONAL
INFORMATION
BASIC OPERATION
ADVANCED
OPERATION
Front panel................................................................i
Remote control ....................................................... ii
List of remote control codes ................................. iii
Optimizing the speaker setting
for your listening room .................................... 24
Selecting the SCENE templates........................... 28
BASIC
OPERATION
Rear panel ................................................................ 10
Placing speakers....................................................... 11
Connecting speakers ................................................ 12
Setting the speaker impedance................................. 13
Information on jacks and cable plugs ...................... 14
Information on HDMI™.......................................... 15
Connecting video components................................. 16
Connecting audio components................................. 19
Using the VIDEO AUX jacks on the front panel ........ 20
Connecting the FM and AM antennas ..................... 20
Connecting the power cable..................................... 21
Turning on and off the power .................................. 21
Front panel display .................................................. 22
SET MENU ............................................................46
PREPARATION
Preparation: Check the items ..................................... 4
Step 1: Set up your speakers...................................... 5
Step 2: Connect your DVD player
and other components............................................ 6
Step 3: Turn on the power
and press SCENE 1 button .................................... 8
What do you want to do with this unit?..................... 9
ADVANCED OPERATION
INTRODUCTION
INTRODUCTION
English
1 En
Features
Features
Built-in 5-channel power amplifier
HDMI (High-Definition Multimedia Interface)
◆ Minimum RMS output power
[Front, Center, Surround channels]
100 W (1 kHz, 0.9% THD, 6 Ω)
◆ HDMI interface for standard, enhanced or high-definition
video (includes 1080p video signal transmission)
SCENE select function
◆ Preset SCENE templates for various situations
◆ SCENE template customizing capability
◆ USB port to connect a USB memory device or a USB portable
audio player
◆ MP3, WMA and WAV capability
Decoders and DSP circuits
Other features
◆ Proprietary Yamaha technology for the creation of multichannel surround sound
◆ Compressed Music Enhancer mode to improve the sound
quality of compression artifacts (such as the MP3 format) to
that of a high-quality stereo
◆ Dolby Digital decoder
◆ Dolby Pro Logic/Dolby Pro Logic II decoder
◆ DTS decoder
◆ Virtual CINEMA DSP
◆ SILENT CINEMA™
◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for
automatic speaker setup
◆ 192-kHz/24-bit D/A converter
◆ Direct Stereo mode for pure hi-fi sound for analog and PCM
2-channel sources
◆ 6 additional input jacks for discrete multi-channel input
◆ OSD (on-screen display) menus that allow you to optimize
this unit to suit your individual audiovisual system
◆ Component video input/output capability
(3 COMPONENT VIDEO INs and 1 MONITOR OUT)
◆ S-video signal input/output capability
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Cinema and music night listening modes
◆ Remote control with preset remote control codes
Sophisticated FM/AM tuner
◆ 40-station random and direct preset tuning
◆ Automatic preset tuning
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
USB features
“DTS” and “DTS Digital Surround” are registered trademarks of
DTS, Inc.
This unit is equipped with the technologies developed by Analog
Devices, Inc. and others. It is strictly prohibited to use this unit
for use other than audiovisual purposes.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing.
2 En
Since hearing damage from loud sounds is often
undetectable until it is too late, Yamaha and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
Getting started
Getting started
■ Installing batteries in the remote control
Check that you received all of the following parts.
Remote control
POWER
POWER
TV
AV
MULTI CH IN
STANDBY
POWER
MUTE
AUDIO SEL
SLEEP
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
AMP
TV INPUT
TV MUTE
1
2
V-AUX
Batteries (2)
(AAA, R03, UM-4)
1
AM loop antenna
3
TV CH
USB
INTRODUCTION
■ Checking the supplied accessories
TV VOL
SCENE
BAND LEVEL
TITLE
3
4
VOLUME
MENU
Optimizer
microphone
ENTER
DISPLAY
RETURN
2
Indoor FM antenna
REC
FREQ/TEXT
l
1
EON
PROG h
2
MODE – PTY SEEK – START
ENHANCER STRAIGHT
3
4
DIRECT ST.
SUR.DECODE NIGHT
5
6
7
9
0
10
8
ENT
Note
1
Take off the battery compartment cover.
The form of the supplied accessories varies depending on the
models.
2
Insert the two supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3
Snap the battery compartment cover back
into place.
Notes
• Change all of the batteries if you notice the following condition:
– the operation range of the remote control decreases.
• Do not use an old battery and a new one together.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries and set up the remote control
code.
English
3 En
Quick start guide
Quick start guide
The following steps describe the easiest way to enjoy
DVD movie playback in your home theater.
Video monitor
Front right
speaker
Front left
speaker
Preparation: Check the items
In these steps, you need the following supplied
accessories.
Subwoofer
Surround right
speaker
❏ Indoor FM antenna
❏ AM loop antenna
The following items are not included in the package of this
unit.
Center speaker
❏ Speakers
❏ Front speakers ...................................... 2
❏ Center speaker ...................................... 1
❏ Surround speakers ............................... 2
Select magnetically shielded speakers. The
minimum required speakers are two front speakers.
DVD player
Surround left
speaker
❏ Active subwoofer ...................................... 1
Select an active subwoofer equipped with an RCA
input jack.
Step 1: Set up your speakers
☞ P. 5
Step 2: Connect your DVD player
and other components
☞ P. 6
Step 3: Turn on the power and
press SCENE 1 button
☞ P. 8
Enjoy DVD playback!
4 En
❏ Speaker cables .......................................... 5
❏ Subwoofer cable ........................................ 1
Select a monaural RCA cable.
❏ DVD player ................................................. 1
Select DVD player equipped with coaxial digital
audio output jack and composite video output
jack.
❏ Video monitor ............................................. 1
Select a TV monitor, video monitor or projector
equipped with a composite video input jack.
❏ Video cable ................................................ 2
Select an RCA composite video cable.
❏ Digital coaxial audio cable ....................... 1
Quick start guide
Be sure to connect the left channel (L), right channel
(R), “+” (red) and “–” (black) properly.
Step 1: Set up your speakers
Front speakers
SPEAKERS
ANTENNA
OUT
DVD
COMPONENT VIDEO
DVD
DTV/CBL
DVR
DVD
DTV/CBL
AC OUTLETS
Loosen
DTV/CBL
IN
Insert
Tighten
HDMI
VIDEO
MONITOR
OUT
INTRODUCTION
Place your speakers in the room and connect them to this
unit.
DVR OUT
MONITOR
OUT
AM
S VIDEO
PR
GND
DIGITAL INPUT
PB
FM
R SURROUND L
CENTER
R FRONT B
L
R FRONT A
L
75
UNBAL.
OPTICAL
CD
3
DTV/
CBL
2
DVD
1
VIDEO
AUDIO
MULTI CH INPUT
FRONT
SURROUND
L
DTV/CBL
IN
DVR OUT
OUTPUT
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
L
R
COAXIAL
DVD
CENTER
R
SUBWOOFER
1
Place your speakers and subwoofer in the
room.
2
Connect speaker cables to each speaker.
To the front
right speaker
Front left speaker
Center and surround speakers
Cables are colored or shaped differently, perhaps with
a stripe, groove or ridge. Connect the striped
(grooved, etc.) cable to the “+” (red) terminals of
your speaker. Connect the plain cable to the “–”
(black) terminals.
3
Connect each speaker cable to the
corresponding speaker terminal of this unit.
1
2
3
To the
surround
right speaker
To the surround
left speaker
To the center
speaker
4
4
Connect the subwoofer cable to the input
jack of the subwoofer and the SUBWOOFER
OUTPUT jack of this unit.
1 Make sure that this unit and the subwoofer are
unplugged from the AC wall outlets.
2 Twist the exposed wires of the speaker cables
together to prevent short circuits.
3 Do not let the bare speaker wires touch each other.
4 Do not let the bare speaker wires touch any metal
part of this unit.
Subwoofer
AV receiver
OUTPUT
IN
(PLAY)
MD/ OUT
CD-R (REC)
SUB
WOOFER
Input jack
SUBWOOFER
OUTPUT jack
Subwoofer cable
English
5 En
Quick start guide
Step 2: Connect your DVD player
and other components
SPEAKERS
ANTENNA
OUT
DVD
COMPONENT VIDEO
DVD
DTV/CBL
DVD
DTV/CBL
Connect the video cable to the composite
video output jack of your DVD player and the
DVD VIDEO jack of this unit.
AC OUTLETS
AV receiver
DTV/CBL
HDMI
VIDEO
MONITOR
OUT
DVR
2
IN
DVR OUT
MONITOR
OUT
AM
S VIDEO
PR
GND
DIGITAL INPUT
PB
FM
R SURROUND L
CENTER
R FRONT B
L
75
UNBAL.
OPTICAL
CD
3
DTV/
CBL
2
DVD
1
Y
COAXIAL
DVD player
VIDEO
AUDIO
MULTI CH INPUT
FRONT
SURROUND
DVD
CENTER
L
L
R
R
DTV/CBL
IN
DVR OUT
OUTPUT
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
R FRONT A
SUBWOOFER
L
DVD VIDEO jack
Make sure that this unit and the DVD
player are unplugged from the AC wall
outlets.
Composite video
output jack
3
1
Connect the digital coaxial audio cable to the
digital coaxial audio output jack of your DVD
player and the DVD DIGITAL INPUT COAXIAL
jack of this unit.
DVD player
Video cable
Connect the video cable to the video input
jack of your video monitor and the VIDEO
MONITOR OUT jack of this unit.
Video monitor
AV receiver
AV receiver
L/MONO
S-VIDEO
VIDEO
VIDEO-1 IN
AUDIO
R
Y
PB
PR
L/MONO
COLOR STREAM HD
IN
R
AUDIO
Video input jack
Digital coaxial
audio output jack
Video cable
Digital coaxial audio
cable
6 En
DVD DIGITAL INPUT
COAXIAL jack
VIDEO MONITOR OUT
jack
Quick start guide
4
■ For further connections
• Using the other kind of speaker
combinations
☞ P. 12
• Connecting a video monitor
☞ P. 16
• Connecting a DVD player
☞ P. 16
INTRODUCTION
Connect the FM and AM antennas to this
unit.
See page 20 for the details.
• Connecting a DVD recorder
☞ P. 16
• Connecting a cable TV or a satellite tuner
☞ P. 16
AM loop antenna
• Connecting a CD player and an MD
recorder
☞ P. 19
Indoor FM antenna
• Connecting a DVD player via analog
multi-channel audio connection
☞ P. 19
• Using the VIDEO AUX jacks on the front
panel
☞ P. 20
Open the lever
Insert
Close the lever
• Connecting an outdoor FM/AM antenna
☞ P. 20
• Using the USB jack on the front panel
☞ P. 43
y
The wire of the AM loop antenna does not have any polarity and
you can connect either end of the wire to AM and GND terminal.
Note
The shape of the AM and GND terminals may vary depending on
the unit.
5
Connect the power plug of this unit and other
components into the AC wall outlet.
y
This unit is equipped with AC OUTLETS for the power supply of
the other components. See page 21 for details.
English
7 En
Quick start guide
Step 3: Turn on the power and
press SCENE 1 button
Check the type of the connected speakers.
If the speakers are 6 ohm speakers, set “SP IMP.” to
“6Ω MIN” before using this unit (see page 13).
1
Turn on the video monitor connected to this
unit.
2
Press 1 STANDBY/ON on the front panel.
4
Start playback of the desired DVD on your
player.
5
Rotate 8 VOLUME to adjust the volume.
Note
When you change the input source or sound field program, the
SCENE mode is deactivated, and the indicator on the selected
SCENE button turns off.
■ Using the other SCENE buttons
In the following cases, try pressing the corresponding
SCENE button to enjoy playback of the desired sources.
Note
Case A: “I want to listen to a music disc from the
connected DVD player as the back ground
music for this room...”
Press F SCENE 2 (or
E SCENE 2) to select
“Disc Listening”.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
3
Press F SCENE 1.
“DVD Viewing” appears in the front panel display,
and this unit automatically optimize own status for
the DVD playback.
Case B: “I want to watch a TV program...”
Press FSCENE 3 (or
E SCENE 3) to select
“TV Viewing”.
Note
To use the “TV Viewing” template, you must connect a
cable TV or a satellite tuner to this unit in advance. See
page 16 for details.
y
The indicator on the selected SCENE button lights up while
this unit is in the SCENE mode.
8 En
Quick start guide
Case C: “I want to listen to a music program from
the FM radio station...”
Notes
• To use the “Radio Listening” template, you must tune into
the desired radio station in advance. See pages 40 to 42 for
tuning information.
• To achieve the best possible reception, orient the
connected AM loop antenna, or adjust the position of the
end of the indoor FM antenna.
■ Customizing the SCENE templates
• Using various SCENE templates
☞ P. 28
• Creating your original SCENE templates
☞ P. 31
■ Using various input sources
y
• Basic controls of this unit
If you cannot find the desired situation, you can select and change
the assigned SCENE template for the SCENE buttons. See
page 28 for details.
• Enjoying FM/AM radio programs
■ After using this unit...
Press 1 STANDBY/ON on the front panel to set
this unit to the standby mode.
INTRODUCTION
Press F SCENE 4 (or
E SCENE 4) to select
“Radio Listening”.
What do you want to do with this
unit?
☞ P. 32
☞ P. 40
• Using your USB portable device with this
unit
☞ P. 43
■ Using various sound features
• Using various sound field programs
☞ P. 37
• Using the pure direct mode for the high
fidelity sound
☞ P. 34
• Customizing the sound field programs
☞ P. 39
■ Adjusting the parameters of this unit
This unit is set to the standby mode. To turn on this unit
from the standby mode, press 1 STANDBY/ON (or
M POWER). See page 21 for details.
Note
In the standby mode, this unit consumes a small amount of power
in order to receive infrared signals from the remote control.
• Automatically optimizing the speaker
parameters for your listening room
(AUTO SETUP)
☞ P. 24
• Manually adjusting various parameters of
this unit
☞ P. 46
• Setting the remote control
☞ P. 56
• Adjusting the advanced parameters
☞ P. 60
■ Additional features
☞ P. 36
9 En
English
Automatically turning off this unit
Connections
Connections
Rear panel
2
1
3 4
5
ANTENNA
OUT
DVD
6
SPEAKERS
AC OUTLETS
DTV/CBL
HDMI
COMPONENT VIDEO
DTV/CBL
DVD
DVR
VIDEO
DVD
MONITOR
OUT
DTV/CBL
IN
DVR OUT
MONITOR
OUT
AM
S VIDEO
PR
GND
DIGITAL INPUT
PB
FM
R SURROUND L
CENTER
R FRONT B
L
R FRONT A
L
75
UNBAL.
OPTICAL
CD
3
DTV/
CBL
2
Y
VIDEO
MULTI CH INPUT
FRONT
SURROUND
AUDIO
DVD
DTV/CBL
IN
DVR OUT
OUTPUT
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
L
1
R
COAXIAL
DVD
CENTER
L
R
SUBWOOFER
7
8
9
0
1 COMPONENT VIDEO jacks
See page 18 for connection information.
6 AC OUTLETS
See page 21 for connection information.
2 HDMI jacks
See page 17 for connection information.
7 DIGITAL INPUT jacks
See pages 16 and 19 for connection information.
3 VIDEO jacks
See pages 16 and 18 for connection information.
8 MULTI CH INPUT jacks
See page 19 for connection information.
4 ANTENNA terminals
See page 20 for connection information.
9 AUDIO jacks
See pages 16 and 19 for connection information.
5 SPEAKERS terminals
See page 12 for connection information.
0 SUBWOOFER OUTPUT jack
See page 12 for connection information.
10 En
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multichannel audio sources.
FL
C
FR
FR
SW
30˚
FL
SR
PREPARATION
C
SL
SR
SL
60˚
SL
80˚
SR
1.8 m (6 ft)
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the
ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a
center speaker, you can do without it. Best results, however, are obtained with the full system.
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround sounds.
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is
effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction
of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is
not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front
speakers. Turn it slightly toward the center of the room to reduce wall reflections.
English
11 En
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
Caution
• Before connecting the speakers, make sure that this unit is turned off (see page 21).
• Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage
this unit and/or the speakers.
• Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the
speakers away from the monitor.
• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit (see page 13).
Note
A speaker cable is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe,
groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable
to the “–” (black) terminals.
Front speakers (B)
Right
Left
Surround speakers
Right
Left
Center
speaker Subwoofer
Center speaker
ANTENNA
OUT
DVD
COMPONENT VIDEO
DTV/CBL
DVD
DVR
DTV/CBL
AC OUTLETS
HDMI
VIDEO
DVD
MONITOR
OUT
SPEAKERS
DTV/CBL
IN
DVR OUT
MONITOR
OUT
AM
S VIDEO
PR
GND
DIGITAL INPUT
PB
FM
CD
3
DTV/
CBL
2
Y
AUDIO
MULTI CH INPUT
DVD
FRONT
SURROUND
DVD
CENTER
L
DTV/CBL
IN
DVR OUT
R FRONT B
L
R FRONT A
L
OUTPUT
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
SUB
WOOFER
1
R
R
SUBWOOFER
Subwoofer
12 En
CENTER
VIDEO
L
COAXIAL
R SURROUND L
75
UNBAL.
OPTICAL
Right
Left
Front speakers (A)
Connections
■ Before connecting to the SPEAKERS
terminal
A speaker cord is actually a pair of insulated cables
running side by side. Cables are colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals of this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to “6Ω
MIN” as follows BEFORE using this unit.
1
Make sure this unit is turned off.
See page 21 for details about turning on or off this
unit.
2
Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this
unit.
This unit turns on, an the advanced setup menu
appears in the front panel display.
3
Press A PROGRAM l / h repeatedly to
select “SP IMP.”.
The following display appears in the front panel
display.
10 mm (3/8”)
■ Connecting to the SPEAKERS terminals
2
1
Red: positive (+)
Black: negative (–)
3
1
Loosen the knob.
2
Insert the bare end of the speaker wire into
the hole on the terminal.
3
Tighten the knob to secure the wire.
Connecting the banana plug
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables. First, tighten the
knob and then insert the banana plug connector into the
end of the corresponding terminal.
PREPARATION
Remove approximately 10 mm (3/8”) of insulation
from the end of each speaker cable and then
twist the bare wires of the cable together to
prevent short circuits.
Setting the speaker impedance
SP IMP.- 8 MIN
4
Press B STRAIGHT repeatedly to select “6Ω
MIN”.
The following display appears in the front panel
display.
SP IMP.- 6 MIN
5
Press 1 STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
Note
Banana plug
The setting you made is reflected next time you turn on this unit.
English
13 En
Connections
Information on jacks and cable plugs
Audio jacks and cable plugs
DIGITAL AUDIO
DIGITAL AUDIO
L
R
COAXIAL
OPTICAL
(White)
(Red)
(Orange)
L
R
C
AUDIO
Left and right
analog audio
cable plugs
Coaxial
digital audio
cable plug
Video jacks and cable plugs
VIDEO
S VIDEO
(Yellow)
COMPONENT VIDEO
Y
PB
PR
(Green)
O
V
S
Optical
digital
audio cable
plug
Composite
video cable
plug
S-video
cable plug
Y
(Blue)
(Red)
PB
PR
Component
video cable
plugs
■ Audio jacks
■ Video jacks
This unit has three types of audio jacks. Connection
depends on the availability of audio jacks on your other
components.
This unit has three types of video jacks. Connection
depends on the availability of input jacks on your video
monitor.
AUDIO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
VIDEO jacks
For conventional composite video signals transmitted via
composite video cables.
DIGITAL AUDIO COAXIAL jacks
For digital audio signals transmitted via coaxial digital
audio cables.
DIGITAL AUDIO OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
S VIDEO jacks
For S-video signals, separated into the luminance (Y) and
chrominance (C) video signals transmitted on separate
wires of S-video cables.
COMPONENT VIDEO jacks
For component signals, separated into the luminance (Y)
and chrominance (PB, PR) video signals transmitted on
separate wires of component video cables.
Notes
• You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. All digital input jacks are compatible with
digital signals with up to 96 kHz of sampling frequency.
• This unit handles digital and analog signals independently. Thus
audio signals input at the digital jacks are not output at the
analog AUDIO OUT (REC) jacks.
• Pull out the cap from the optical jack before you connect the
optical digital audio cable. Do not discard the cap. When you
are not using the optical jack, be sure to put the cap back in
place. This cap protects the jack from dust.
Video signal flow for MONITOR OUT
Input
COMPONENT
VIDEO
Output
(MONITOR OUT)
PR
PR
PB
PB
Y
Y
S VIDEO
VIDEO
Note
The OSD signal is not output at the DVR OUT (REC) jacks.
14 En
Connections
Information on HDMI™
Audio signals input at the HDMI jack are not output from any speaker terminals but output from the connected video
monitor.
To enjoy the sound from speakers connected to this unit,
– make an analog or digital connection besides the HDMI connection (see page 16).
– mute the volume of the connected video monitor.
■ HDMI jack and cable plug
PREPARATION
You can play back pictures by connecting your video monitor and video source component to this unit using HDMI
connections.
At that time, audio/video signals output from the connected component (such as DVD player etc.) are output to the
connected video monitor only when this unit is turned on and set to the input source (DVD or DTV/CBL).
Furthermore, available audio/video signals depend on the specification of the connected video monitor. Refer to the
instruction manual of each connected component.
HDMI
HDMI cable plug
y
• We recommend using an HDMI cable shorter than 5 meters
(16 feet) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
English
15 En
Connections
Connecting video components
Connect the video components as follows.
y
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
You can also connect a video monitor, DVD player, digital TV,
and cable TV to this unit using the S VIDEO or COMPONENT
VIDEO connections (see page 17).
■ Connecting a video monitor and a DVD
player
OUT
DVD
■ Connecting a cable TV/satellite tuner
and a DVD recorder
OUT
DTV/CBL
DVD
DTV/CBL
HDMI
HDMI
COMPONENT VIDEO
DVD
DTV/CBL
DVR
COMPONENT VIDEO
VIDEO
MONITOR
OUT
DVD
DTV/CBL
IN
DVR OUT
DVD
MONITOR
OUT
S VIDEO
PR
DTV/CBL
DVR
VIDEO
MONITOR
OUT
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
DVD
DTV/CBL
IN
DVR OUT
S VIDEO
PR
DIGITAL INPUT
DIGITAL INPUT
PB
PB
OPTICAL
OPTICAL
VIDEO
SURROUND
L
DVD
DTV/CBL
2
IN
DVR OUT
VIDEO
MULTI CH INPUT
CD
DTV/
CBL
FRONT
R
1
R
R
COAXIAL
SUBWOOFER
R
V
V
Video out
C
Audio out
Video in
Audio out
O
L
Audio out
L
V
Video out
CD
L
SUBWOOFER
Audio out
AUDIO
CENTER
L
DVD
R
SURROUND
2
L
1
COAXIAL
Y
AUDIO
DVD
CENTER
R
V
L
R
L
R
V
Video in
DTV/
CBL
FRONT
3
CD
MULTI CH INPUT
Audio in
Y
Audio out
3
Video out
CD
DVD player
Video monitor
16 En
Cable TV or
Satellite tuner
DVD recorder
indicates recommended connections
indicates recommended connections
indicates alternative connections
indicates alternative connections
Connections
■ Connecting to the HDMI, COMPONENT VIDEO or S VIDEO jacks
You can enjoy high-quality pictures by connecting your video monitor and video source components to this unit using
HDMI, COMPONENT VIDEO or S VIDEO connections.
Note
Be sure to connect your video components in the same way you connect your video monitor to this unit. For example, if you connect
your video monitor to this unit using a HDMI connection, connect your video components to this unit using the HDMI connection.
HDMI connection
Video monitor
Cable TV or
satellite tuner
PREPARATION
Audio signals input at the HDMI jack are not output
from any speaker terminals but output from the
connected video monitor.
To enjoy the sound from speakers connected to this
unit,
– make an analog or digital connection besides the
HDMI connection (see page 16).
– mute the volume of the connected video monitor.
Notes
• When you connect your TV monitor or projector via HDMI
connection, the OSD does not appear. In such cases, connect the
TV monitor or projector via component, S-video or video
connection.
• Connect the input source components to the HDMI DVD or
HDMI DTV/CBL jack to display the video images on the video
monitor connected to the HDMI OUT jack.
• Audio/video signals output from the connected component
(such as DVD player etc.) are output to the connected video
monitor only when this unit is turned on and set to the input
source (DVD or DTV/CBL).
• Available audio/video signals depend on the specification of the
connected video monitor. Refer to the instruction manual of
each connected component.
ANTENNA
OUT
DVD
ENT VIDEO
DVR
DTV/CBL
HDMI
VIDEO
MONITOR
OUT
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
AM
S VIDEO
GND
FM
75
UNBAL.
VIDEO
CH INPUT
SURROUND
AUDIO
DVD
CENTER
DTV/CBL
IN
DVR OUT
CD
IN
MD/
(PLAY) CD-R (
L
R
SUBWOOFER
DVD player
English
17 En
Connections
COMPONENT VIDEO connection
S VIDEO connection
Video monitor
Video monitor
Cable TV or
satellite tuner
Y
PB
PR
Y
PB
Video in
Video out
Video in
Video out
DVD player
S
PR
OUT
S
DVD
DTV/CBL
HDMI
VIDEO
COMPONENT VIDEO
DVD
DTV/CBL
DVR
DVD
DTV/CBL
IN
DVR OUT
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
MONITOR
OUT
S VIDEO
PR
PB
VIDEO
Y
AUDIO
MULTI CH INPUT
FRONT
SURROUND
CENTER
CD
L
L
R
R
SUBWOOFER
18 En
PB
PR
Cable TV or
satellite tuner
DVD recorder
DVD player
Video in
Y
S
S
Video out
PR
Video out
PB
Video out
Y
Video out
S
DVD recorder
Connections
Connecting audio components
Connect the audio components as follows.
■ Connecting a CD player and a CD
recorder/MD recorder
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
Note
When you connect your CD player via analog and digital
connection, priority is given to the signal input at the DIGITAL
INPUT jack.
PREPARATION
DIGITAL INPUT
PB
FM
R SURROUN
75
UNBAL.
OPTICAL
CD
3
DTV/
CBL
2
Y
VIDEO
MULTI CH INPUT
FRONT
SURROUND
AUDIO
DVD
DVD
CENTER
L
DTV/CBL
IN
DVR OUT
OUTPUT
IN
MD/ OUT
(PLAY) CD-R (REC)
CD
SUB
WOOFER
L
1
R
COAXIAL
R
SUBWOOFER
O
L
R
Audio out
L
Audio out
Audio out
CD player
R
L
R
Audio in
CD recorder or
MD recorder
indicates recommended connections
indicates alternative connections
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 6 additional input jacks (FRONT L/R, SURROUND L/R, CENTER and SUBWOOFER) for
discrete multi-channel input from a multi-format player, external decoder or sound processor. Connect the output jacks
on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right
output jacks to the left and right input jacks for the front and surround channels.
MULTI CH INPUT
DTV/
CBL
FRONT
SURROUND
Notes
CENTER
2
L
1
R
COAXIAL
L
R
Center out
R
English
Front out
L
Subwoofer out
SUBWOOFER
Surround out
DVD
• When you select the component connected to the MULTI CH
INPUT jacks as the input source (see page 33), this unit
automatically turns off the digital sound field processor, and
you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH
INPUT jacks to accommodate for missing speakers. We
recommend that you connect a 5.1-channel speaker system
before using this feature.
Multi-format player or
external decoder
19 En
Connections
Using the VIDEO AUX jacks on the
front panel
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit.
Caution
Be sure to turn down the volume of this unit and other
components before making connections.
Connecting the FM and AM
antennas
Both FM and AM indoor antennas are supplied with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
Notes
• The AM loop antenna should be placed away from this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
Notes
To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
VOLUME
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING
l
A/B/C/D/E
FM/AM
h
PRESET/TUNING
Outdoor AM antenna
TUNING AUTO/MAN'L
MEMORY
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
2
3
STRAIGHT
DIRECT STEREO
4
h
TONE CONTROL
l
INPUT
VIDEO AUX
h
AUDIO SELECT
EFFECT
SILENT CINEMA
VIDEO
L
AUDIO
USB
R
Use a 5 to 10 m (16 to 32 ft) of
vinyl-covered wire extended
outdoors from a window.
AM loop
antenna
(supplied)
Indoor FM
antenna
(supplied)
VIDEO AUX
VIDEO
L
V
L
Video
output
AUDIO
R
R
ANTENNA
Audio
output
R
AM
GND
FM
75
UNBAL.
Game console or
video camera
IN
MD/ O
(PLAY) CD-R (R
Ground
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.
20 En
Connections
Connecting the power cable
Once all connections are complete, plug the power cable
into the AC wall outlet.
Turning on and off the power
■ Turning on this unit
Press 1 STANDBY/ON (or M POWER) to turn
on this unit.
AC OUTLETS
y
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
Power cable
Press 1 STANDBY/ON (or N STANDBY) to set
this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
PREPARATION
■ Set this unit to the standby mode
■ AC OUTLETS (SWITCHED)
Use these outlets to supply power to any connected
components. Connect the power cable of your other
components to these outlets. Power to these outlets is
supplied when this unit is turned on. However, power to
these outlets is cut off when this unit is set to the standby
mode. For information on the maximum power or the total
power consumption of the components that can be
connected to these outlets, see “Specifications” on
page 70.
English
21 En
Connections
Front panel display
1
2
4
3
DVR
t
5
V-AUX
DTV/CBL
6
VIRTUAL
ENHANCER
SP SILENT CINEMA
NIGHT
AB
MD/CD-R
DVD
USB
HiFi DSP
7
TUNER
8
CD
YPAO AUTO TUNED STEREO MEMORY
PRESET
SLEEP MUTE
q DIGITAL
q PL
ft
q PL
mS
dB
PCM
0
A
B
C
1 Decoder indicator
The respective indicator lights up when any of the
decoders of this unit functions.
2 ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
selected (see page 37).
3 VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 38).
4 SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 38).
5 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
6 YPAO indicator
Lights up when you run “AUTO SETUP” and when the
speaker settings set in “AUTO SETUP” are used without
any modifications (see page 24).
7 Tuner indicators
Lights up when this unit is in the FM or AM tuning mode
(see pages 40).
8 MUTE indicator
Flashes while the MUTE function is on (see page 36).
9 VOLUME level indicator
Indicates the current volume level.
0 PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
22 En
D
E
9
F
VOLUME
dB
LFE
L C R
SL
SR
G
A Headphones indicator
Lights up when headphones are connected (see page 36).
B SP A B indicators
Light up according to the set of front speakers selected
(see page 33).
C NIGHT indicator
Lights up when you select a night listening mode (see
page 35).
D CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 37).
HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program (see page 37).
E Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
F SLEEP indicator
Lights up while the sleep timer is on (see page 36).
G Input channel and speaker indicators
LFE
L C R
SL
SR
LFE indicator
Input channel indicators
LFE indicator
Lights up when the input signal contains the LFE
signal.
Input channel indicators
Indicate the channel components of the current digital
input signal.
Connections
■ Using the remote control
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
VOLUME
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING
FM/AM
l
A/B/C/D/E
PRESET/TUNING
h
MEMORY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
TONE CONTROL
PROGRAM
2
3
STRAIGHT
NIGHT
h
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
USB
R
EFFECT
SILENT CINEMA
30º
PREPARATION
30º
Approximately 6 m (20 ft)
Y Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
y
To set the remote control codes for other components, see
page 59.
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperatures
– dusty places
English
23 En
Optimizing the speaker setting for your listening room
Optimizing the speaker setting for your listening room
This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO SETUP
2
Notes
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
OPTIMIZER MIC
• Be advised that it is normal for loud test tones to be output
during the “AUTO SETUP” procedure.
• To achieve the best results, make sure the room is as quiet as
possible while the “AUTO SETUP” procedure is in progress. If
there is too much ambient noise, the results may not be
satisfactory.
Y
TUNING AUTO/MAN'L
VIDEO AUX
AUDIO SELECT
VIDEO
L
AUDIO
USB
R
y
You can run “AUTO SETUP” using the system menu that appears
in the OSD or in the front panel display. This manual uses the
OSD illustrations to explain the “AUTO SETUP” procedure.
1
Optimizer
microphone
The following display appears in the OSD.
AUTO:MENU
SETUP;;;;;;;AUTO
. START
3
p
Automatic
processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
p
Make sure of the following check points
before starting the AUTO SETUP operations.
❏ Speakers are connected appropriately.
❏ Headphones are disconnected from this unit.
❏ This unit and the video monitor are turned on.
❏ The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
❏ The crossover frequency controls of the
connected subwoofer is set to the maximum.
❏ FRONT A speakers are selected as the front
speaker system (see page 33).
❏ The room is sufficiently quiet.
Place the optimizer microphone at your
normal listening position on a flat level
surface with the microphone heading
upward.
Optimizer microphone
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would be
when you are seated in your listening position. You can use the
attached screw of a tripod (etc.) to fix the optimizer microphone
to the tripod (etc.).
24 En
Optimizing the speaker setting for your listening room
The display changes as follows.
4
Make sure that “SETUP” is set to “AUTO”
and the pointer is pointing at “START”.
AUTO:MENU
y
SETUP;;;;;;;AUTO
. START
You can also select the following setup methods. In this
case, press G k to select “SETUP”, press G l / h to
select the one of the following choises and then select
“START”.
PREPARATION
Choices: AUTO, RELOAD, UNDO, DEFAULT
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
• Select “RELOAD” to reload the last “AUTO
SETUP” settings and override the previous
settings.
• Select “UNDO” to undo the last “AUTO SETUP”
settings and restore the previous settings.
• Select “DEFAULT” to reset the “AUTO SETUP”
parameters to the initial factory settings.
p
p
Automatic
processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
AUTO:CHECK
INITIALIZING
. WIRING/LEVEL
DISTANCE
SIZE
[
WAITING;;;
;;;;;;;;;;
[]:Exit
Note
“RELOAD” or “UNDO” is available only when you have
previously run “AUTO SETUP” and confirmed the results.
5
Press D AMP and then press G ENTER to
start the setup procedure.
This unit starts the auto setup procedure. Loud test
tones are output from each speaker during the auto
setup procedure. Once all items are set, the
“AUTO:RESULT” display appears in the OSD.
Notes
• During the auto setup procedure, do not perform any
operation on this unit.
• We recommend getting out of the room while this unit is in
the auto setup procedure. It takes approximately 3 minutes
for this unit to complete the auto setup procedure.
This unit performs the following checks:
Speaker wiring/volume level WIRING/LEVEL
Checks which speakers are connected and the
polarity of each speaker. Also checks and adjusts the
volume level of each speaker.
Speaker distance DISTANCE
Checks the distance of each speaker from the
listening position and adjusts the timing of each
channel.
NO WARNING
RESULT
SP :
3/2/0.1
DIST: 3.2/3.5m
LVL :
-2/+2dB
. >SET
CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
The results displayed under “RESULT” are as follows.
Number of speakers SP
Displays the number of speakers connected to this unit in
the following order:
Front/Back/Subwoofer
Speaker distance DIST
Displays the speaker distance from the listening position
in the following order:
Closest speaker distance/Farthest speaker distance
Speaker level LVL
Displays the speaker output level in the following order:
Lowest speaker output level/Highest speaker output level
Notes
• If “E-6:INTERNAL ERROR” appears during the testing
procedure, restart from step 4.
• If you selected “RELOAD” in step 4, no test tones are output.
• If an error occurs during the “AUTO:CHECK” procedure, the
setup procedure is canceled and an error screen appears. For
details, see “If an error screen appears” on page 27.
• When this unit detects potential problems during the “AUTO
SETUP” procedure, “WARNING” and the number of warning
messages appears in the above of “RESULT” (see page 27).
English
Speaker size SIZE
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
channel.
AUTO:RESULT
25 En
Optimizing the speaker setting for your listening room
6
Press G ENTER to display the setup results
in detail.
7
Press G l / h repeatedly to toggle between
the setup result displays.
9
Make sure the pointer is pointing at “SET”
and “CANCEL” and then press G l / h to
select “SET” or “CANCEL”.
Choices: SET, CANCEL
• Select “SET” to confirm the “AUTO SETUP”
results.
• Select “CANCEL” to cancel the “AUTO SETUP”
results.
10
Press G ENTER to confirm your selection.
The top “SET MENU” display appears in the OSD.
Results of the speaker
connection and wiring
Results of the speaker
distance from the
listening position
SET MENU
TOP MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
Results of the speaker
size
If you are not satisfied with the results or want to manually
adjust each parameter, run “MANUAL SETUP” (see
page 46).
Note
The distances displayed in the “DISTANCE” results may be
longer than the actual distance depending on the
characteristics of your speakers.
8
Press G ENTER to return to the
“AUTO:RESULT” display.
AUTO:RESULT
NO WARNING
RESULT
SP :
3/2/0.1
DIST: 3.2/3.5m
LVL :
-2/+2dB
. >SET
CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
26 En
p
y
p
Results of the speaker
output level
[ ]/[ ]:Up/Down
[ENTER]:Enter
11
Press Q MENU to exit from “SET MENU”.
12
Disconnect the optimizer microphone from
this unit.
The optimizer microphone is sensitive to heat. Keep it
away from direct sunlight and do not place it on top
of this unit.
y
If you change speakers, speaker positions, or the layout of
your listening environment, run “AUTO SETUP” again to
recalibrate your system.
Optimizing the speaker setting for your listening room
■ If an error screen appears
Press G k / n / l / h to select “RETRY” or
“EXIT” and then press G ENTER.
The following display is an example where “E-5:USER
CANCEL” appears in the OSD.
■ If “WARNING” appears
When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” appears in the
“RESULT:EXIT” display. Check the warning messages to
correct your speaker settings.
Note
AUTO:ERROR
. E-5:USER CANCEL
Don't operate
any function
Warnings differ from errors in that warnings do not cancel the
“AUTO SETUP” procedure.
1
EXIT
[ ]/[ ]:Select
[ENTER]:Return
Choices: RETRY, EXIT
• Select “RETRY” to retry the “AUTO SETUP”
procedure.
• Select “EXIT” to exit from the “AUTO SETUP”
procedure.
Make sure the pointer is pointing at
“WARNING” and then press G ENTER to
display the detailed information about the
warning.
The number on the right of “WARNING” indicates
the number of warning messages.
PREPARATION
>RETRY
AUTO:RESULT
. WARNING(1)
RESULT
SP :
3/2/0.1
DIST: 3.2/3.5m
LVL :
-2/+2dB
CANCEL
>SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
2
Press Gl / h repeatedly to toggle between
the warning displays.
WARNING:W-1
<OUT OF PHASE>
Reverse Channel
-FR
CENTER
--[p]/[[]:Select
[ENTER]:Return
y
• For details about each warning message, see the “AUTO
SETUP” section in “Troubleshooting” on page 65.
• When the corresponding warning message is not
applicable to a speaker, “– –” is displayed instead.
3
Press G ENTER to return to the top
“RESULT:EXIT” display.
English
27 En
SELECTING THE SCENE TEMPLATES
Selecting the SCENE templates
This unit is equipped with 15 preset SCENE templates for
various situations of using this unit. As the initial factory
setting, the following SCENE templates are assigned to
each SCENE button:
2
Press D INPUT l / h (or press D AMP and
then press G l / h) to select the desired
template.
SCENE 1: DVD Viewing
SCENE 2: Disc Listening
SCENE 3: TV Viewing
SCENE 4: Radio Listening
l
INPUT
h
Front panel
If you want to use other SCENE templates, you can select
the desired SCENE templates from the SCENE template
library and assign the templates to the selected SCENE
buttons on the front panel and the remote control.
or
AMP
ENTER
Select the desired SCENE
template
Remote control
1
DVD MovieView
Assign the
SCENE
template to the
SCENE button
SCENE template library
(Image)
Selecting the desired SCENE
template
1
Press and hold the desired F SCENE (or
E SCENE) button for 3 seconds.
The indicator on the selected SCENE button on the
front panel starts to flash, and the name of the
currently assigned SCENE template appears in the
front panel display.
3 seconds
3 seconds
1
or
1
Front panel
Remote control
1
Flashes
DVD Viewing
28 En
3
Press the F SCENE (or E SCENE) button
again to confirm the selection.
The selected SCENE template is assigned to the
button.
1
Front panel
or
1
Remote control
Notes
• If you do not carry out any operation within 30 seconds from
the last operation in these steps, this procedure is automatically
canceled.
• Once the desired SCENE templates are assigned to the
corresponding SCENE buttons, you may need to set the input
source of the SCENE template on the remote control. See
page 56 for details.
Selecting the SCENE templates
■ Which SCENE template would you like to select?
Which source do you like to
play back?
Video sources
(DVD video,
Recorded video)
Which component do you
like for playback?
DVD
SCENE template
DVD Viewing
Default SCENE
buttons
1
DVD Movie Viewing
DVD Live Viewing
Music discs (CD,
SACD or DVD-Audio)
DVR
DVR Viewing
DVD
Disc HiFi Listening
Music Disc Listening
CD
BASIC
OPERATION
Disc Listening
2
CD HiFi Listening
CD Listening
CD Music Listening
Radio programs
USB memory device
or USB portable
audio player
TV programs
TUNER (FM/AM)
USB
DTV/CBL
Radio Listening
4
USB Audio Listening
TV Viewing
3
TV Sports Viewing
Video games
V-AUX
Game Playing
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 31 for details.
English
29 En
Selecting the SCENE templates
■ Preset SCENE templates descriptions
CD Listening
SCENE template
Select this SCENE template when you play back music discs on
your CD player.
Features
Input source
Playback mode
CD
2ch Stereo
DVD Viewing
(SCENE 1 as the default setting)
CD Music Listening
Select this SCENE template when you play back general contents
on your DVD player.
Select this SCENE template when you play back the music source
on your CD player as the background music.
DVD
CD
STRAIGHT
Radio Listening
(SCENE 4 as the default setting)
DVD Movie Viewing
Select this SCENE template when you play back movies on your
DVD player.
DVD
5ch Stereo
Select this SCENE template when you enjoy FM or AM radio
programs.
Movie Dramatic
TUNER
DVD Live Viewing
MUSIC ENHANCER
5ch STEREO
\
Select this SCENE template when you enjoy music live video on
your DVD player.
DVD
Pop/Rock
Select this SCENE template when you play back movies on your
digital video recorder.
Movie Dramatic
Disc HiFi Listening
TV Viewing (SCENE 3 as the default setting)
Select this SCENE template when you enjoy TV programs.
DTV/CBL
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your DVD player.
DVD
DIRECT STEREO
Music Disc Listening
2ch Stereo
Select this SCENE template when you enjoy sports programs on
TV.
DTV/CBL
Select this SCENE template when you play back music sources on
your DVD player as the background music.
DVD
5ch Stereo
CD HiFi Listening
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your CD player.
CD
30 En
DIRECT STEREO
TV Sports
Game Playing
Select this SCENE template when you play video games.
V-AUX
Disc Listening
(SCENE 2 as the default setting)
STRAIGHT
TV Sports Viewing
Select this SCENE template when you play back music discs on
your DVD player.
DVD
MUSIC ENHANCER
5ch STEREO
USB
DVR Viewing
DVR
USB Audio Listening
Select this SCENE template when you play back music on your
USB memory device or a USB portable audio player.
Game
Selecting the SCENE templates
Creating your original SCENE
templates
3
You can create your original SCENE templates for each
SCENE button. You can refer to the preset 15 SCENE
templates to create the original SCENE templates.
■ Customizing the preset SCENE
templates
• INPUT:
• MODE:
Create the original SCENE
template
SCENE template library
(Image)
4
Press the E SCENE button again to confirm
the edit.
1
BASIC
OPERATION
The input source component
The active sound field programs,
STRAIGHT or DIRECT STEREO
mode (see pages 34 and 38)
• NIGHT:
The night listening mode setting (see
page 35)
− SYSTEM: Keeps the current night listening
mode.
− CINEMA: Sets the night listening mode to the
CINEMA mode.
− MUSIC: Sets the night listening mode to the
MUSIC mode.
Use this feature to customize the preset SCENE templates.
Select a SCENE template
Press G k / n to select the desired parameter
of the SCENE template and then G l / h to
select the desired value of the selected
parameter.
You can adjust the following parameters for a SCENE
template:
1
Assign to the SCENE
button
y
1
2
Turn on the video monitor connected to this
unit.
Press and hold the desired E SCENE button
for 3 seconds and then press D AMP.
The SCENE template customizing screen appears on
the video monitor.
AMP
1
3 seconds
An asterisk mark (*) appears by the name of the original SCENE
template.
Notes
• Once the desired SCENE templates are assigned to the
corresponding E SCENE buttons, you may need to set the
input source of the SCENE template on the remote control. See
page 56 for details.
• You can create a customized SCENE template for each
E SCENE button, and if you create another customized
SCENE template, this unit overwrites the old customized
SCENE template with the new one.
• The newly created template is only available for the assigned
E SCENE button.
■ Renaming the SCENE templates
Note
When the SCENE template you want to customize is not
assigned to any of the E SCENE button, press G l / h
repeatedly to recall the desired SCENE template on the
menu screen.
31 En
English
Select “SCENE” in step 3 of “Customizing the
preset SCENE templates” and then press
G ENTER.
• Press G k / n to select the desired character.
• Press G l / h to place “_” (underscore) under the
space or the desired character.
• Press H RETURN to cancel the new name.
• Press G ENTER to confirm the new name.
PLAYBACK
Playback
Caution
Extreme caution should be exercised when you play
back CDs encoded in DTS. If you play back a CD
encoded in DTS on a DTS-incompatible CD player,
you will only hear some unwanted noise that may
damage your speakers. Check whether your CD player
supports CDs encoded in DTS. Also, check the sound
output level of your CD player before you play back a
CD encoded in DTS.
5
Press A PROGRAM l / h (or press D AMP
and then J PROG l / h) repeatedly to
select the desired sound field program.
The name of the selected sound field program appears
in the front panel display.
See page 37 for details about sound field programs.
Movie Dramatic
Basic operations
1
2
Currently selected
surround field program
Turn on the video monitor connected to this
unit.
Press D INPUT l / h repeatedly (or press
one of the input selector buttons (C)) to
select the desired input source.
The name of the currently selected input source
appears in the front panel display for a few seconds.
Available input source
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
USB
INPUT:DVD
Currently selected input source
Notes
• Choose a sound field program based on your listening
preference, not merely on the name of the program.
• When you select an input source, this unit automatically
selects the last sound field program used with the
corresponding input source.
• Sound field programs cannot be selected when the
component connected to the MULTI CH INPUT jacks is
selected as the input source (see page 33).
• When PCM signals with a sampling frequency higher than
48 kHz are input, this unit is automatically set to the
“STRAIGHT” mode (see page 38).
• To display information about the currently selected input
source in the OSD, see page 35 for details.
■ A quick guide to contents
When you want to...
3
4
Start playback on the selected component or
select a broadcast station.
• Refer to the operating instructions for the source
component.
• See page 40 for details about FM/AM tuning
instructions.
Rotate 8 VOLUME (or press R VOLUME +/–)
to adjust the volume to the desired output
level.
32 En
See
page
Enjoy pure hi-fi stereo sound
34
Adjust the tonal quality of the front speakers
34
Adjust the parameters of sound field programs
39
Enjoy the sources with a wide dynamic range at night
35
Use headphones
36
Select a decoder to play back sources with
38
Automatically set this unit to the standby mode
36
Playback
Additional operations
■ Selecting the component connected to
the MULTI CH INPUT jacks as the input
source
Press D INPUT l / h repeatedly (or press
AMULTI CH IN) so that “MULTI CH” appears in
the front panel display.
■ Using the Zone B feature
When you set “FRONT B” to “ZONE B” (see page 48),
you can use the speakers connected to the FRONT B
speaker terminals in another room (Zone B).
Press 9 SPEAKERS on the front panel
repeatedly to turn on or off the Zone B speakers.
When you activate the Zone B speakers, all the speakers in
the main room are muted.
Notes
y
Use “MULTI CH SET” menu in “INPUT MENU” to set the
parameter for MULTI CH INPUT (see page 54).
Notes
■ Selecting audio input jacks
(AUDIO SELECT)
■ Selecting the front speaker set
This unit comes with a variety of input jacks. Use this
feature (audio input jack select) to switch between input
jacks when more than one input jack is assigned to the
same input source.
Use this feature to select the front speaker system
(FRONT A or FRONT B).
y
Press 9 SPEAKERS on the front panel
repeatedly to turn on or off the set of front
speakers connected to the FRONT A or FRONT B
speaker terminals.
The activate front speaker set changes as follows:
FRONT A
BASIC
OPERATION
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source.
• When headphones are used, signals are output only from the
front left and right channels.
• You cannot activate both the main room and Zone B speakers
simultaneously.
• If you select CINEMA DSP sound field program and activate
the Zone B speakers, Virtual CINEMA DSP activates
automatically (see page 38).
• We recommend setting audio input jack select to “AUTO” in
most cases.
• You can adjust the default audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 55).
Press E AUDIO SELECT (or B AUDIO SEL)
repeatedly to select the desired audio input jack
select setting.
DVR
FRONT B
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
USB
A.SEL:AUTO
Off
Audio input jack
select setting
Note
Turn off the volume level of this unit when you switch the front
speaker setting.
AUTO
ANALOG
Automatically selects input signals in the
following order:
(1) Digital signals
(2) Analog signals
Selects only analog signals. If no analog
signals are input, no sound is output.
Note
This feature is not available when no digital input jacks are
assigned to the currently selected input source.
English
33 En
Playback
■ Enjoying pure hi-fi stereo sound
The DIRECT STEREO mode allows sources to bypass the
decoders and DSP processors of this unit so that you can
enjoy pure hi-fi sound from 2-channel PCM and analog
sources.
■ Adjusting speaker levels during
playback
You can adjust the output level of each speaker while
listening to a music source.
Note
Press C DIRECT STEREO (or press D AMP and
then press V DIRECT ST.) to select “DIRECT
STEREO”.
Notes
This operation will override the level adjustments made in
“AUTO SETUP” (see page 24) and “SP LEVEL” (see page 50).
1
• To avoid unexpected noise, do not play CDs encoded in DTS
when the DIRECT STEREO mode is selected.
• When multi-channel signals (Dolby Digital and DTS) are input,
this unit automatically switches to the corresponding analog
input.
• No sound will be output from the subwoofer.
• “TONE CONTROL” (on this page) and “SOUND MENU” (see
page 48) settings (except for speaker level settings) are not
effective.
• The front panel display automatically dims.
Display
■ Adjusting the tonal quality
Press 0 TONE CONTROL repeatedly to select
“BASS” or “TREBLE” and then press
A PROGRAM l / h (or J PROGl / h) to
adjust the corresponding frequency response
level.
• Select “BASS” to adjust the low-frequency response.
• Select “TREBLE” to adjust the high-frequency
response.
Notes
• Speaker and headphone adjustments are stored independently.
• If you increase or decrease the high-frequency or low-frequency
sound to an extreme level, the tonal quality of the surround
speakers may not match that of the front left and right speakers.
34 En
Press D AMP and then press FLEVEL
repeatedly to select the speaker you want to
adjust.
Adjusted speaker
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SWFR
Subwoofer
SUR.L
Surround left speaker
SUR.R
Surround right speaker
y
Once you press F LEVEL on the remote control, you can
also select the speaker by pressing Gk / n.
2
Press Gl / h on the remote control to
adjust the speaker output level.
The control range is from +10 dB to –10 dB.
y
You can press 4 A/B/C/D/E to select a speaker and then
5 PRESET/TUNING l / h to adjust the speaker output
level.
Playback
■ Selecting the night listening mode
■ Displaying signal information
The night listening modes are designed to improve
listenability at lower volumes or at night.
You can display the format, sampling frequency, channel,
bit rate and flag data of the current input signal.
1
1
Press D AMP and then press Q MENU on
the remote control.
The top “SET MENU” display appears in the OSD.
SET MENU
TOP MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
Press D AMP and then press L NIGHT
repeatedly to select “NIGHT:CINEMA” or
“NIGHT:MUSIC”.
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” to reduce the dynamic
range of film soundtracks and make dialog easier to
hear at lower volumes.
• Select “NIGHT:MUSIC” to preserve ease-oflistening for all sounds.
• Select “OFF” if you do not want to use this feature.
y
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
Press Gl / h to adjust the effect level while
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
displayed in the front panel display.
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
Press Gn repeatedly to select “SIGNAL
INFO” and then press GENTER.
The following information about the input source
appears in the OSD.
;SIGNAL INFO
. FORMAT
DolbyD
SAMPLING
48kHz
CHANNEL 3/2/0.1
BITRATE 384kbps
FLAG
None
BASIC
OPERATION
2
2
[RETURN]:Exit
y
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently.
Display
Notes
• You cannot use the night listening modes in the following cases:
– when the DIRECT STEREO mode (see page 34) is selected.
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source.
– when headphones are connected to the PHONES jack.
– when the sound field program is selected while you enjoy
music contents in a USB memory device etc.
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
Description
FORMAT
Signal format.
SAMPLING
The number of samples per second taken
from a continuous signal to make a
discrete signal.
CHANNEL
The number of source channels in the
input signal (front/surround/LFE).
BITRATE
The number of bits passing a given point
per second.
FLAG
Flag data encoded in DTS, Dolby Digital,
or PCM signals that cue this unit to
automatically switch decoders.
y
The information indicated by the cursor is also displayed in
the front panel display.
3
Press Q MENU again to exit from “SET
MENU”.
English
35 En
Playback
■ Playing video sources in the
background
■ Muting the audio output
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Press O MUTE to mute the audio output.
Press O MUTE again to resume the audio output.
Press the input selector buttons on the remote
control to select a video source and then an
audio source.
MULTI CH IN
CD
MD/CD-R
DTV/CBL
• You can also rotate 8 VOLUME (or press RVOLUME +/–) to
resume the audio output.
• You can adjust the muting level by using “MUTE TYPE” in
“SOUND MENU” (see page 51).
• The MUTE indicator flashes in the front panel display when the
audio output is muted and disappears from the front panel
display when the audio output is resumed.
■ Using the sleep timer
TUNER
Audio sources
DVD
y
Use this feature to automatically set this unit to the
standby mode after a certain amount of time. The sleep
timer also automatically turns off any external
components connected to the AC OUTLETS (see
page 21).
DVR
Video sources
V-AUX
■ Using your headphones
Connect a pair of headphones with a stereo
analog audio cable plug to the PHONES jack on
the front panel.
Press D AMP and then press PSLEEP
repeatedly to set the amount of time.
Each time you press PSLEEP, the front panel display
changes as shown below.
SLEEP 120min
SLEEP OFF
VOLUME
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING
FM/AM
CATEGORY
A/B/C/D/E
l
PRESET/TUNING/CH
h
MEMORY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SILENT CINEMA
SPEAKERS
A/B/OFF
TONE CONTROL
PROGRAM
2
3
STRAIGHT
DIRECT STEREO
h
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
USB
R
SLEEP 90min
SLEEP 30min
SLEEP 60min
The SLEEP indicator flashes while you are switching the
amount of time for the sleep timer. Once the sleep timer is
set, the SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound field
program.
EFFECT
y
• To cancel the sleep timer, press P SLEEP on the remote
control repeatedly until “SLEEP OFF” appears in the front
panel display.
• You can also cancel the sleep timer setting by pressing
1 STANDBY/ON (or N STANDBY) to set this unit to the
standby mode.
y
When you select a sound field program, SILENT CINEMA mode
activates automatically (see page 38).
Notes
• When you connect headphones, no signals are output at the
speaker terminals.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
36 En
SOUND FIELD PROGRAMS
Sound field programs
This unit is equipped with a variety of precise digital
decoders that allow you to enjoy multi-channel playback
from almost any stereo or multi-channel sound source.
Press A PROGRAM l / h (or press D AMP and
then press J PROG l / h repeatedly).
The name of the selected sound field program appears in
the front panel display.
y
• Choose a sound field program based on your listening
preference, not merely on the name of the program itself.
• You can select “Music Enh. 2ch” and “Music Enh. 5ch” by
pressing U ENHANCER on the remote control repeatedly.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 33).
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode.
• The sound field program is canceled when the night listening
mode is selected while you enjoy music contents in a USB
memory device etc.
Sound field program descriptions
MUSIC
Program
Pop/Rock
CINEMA DSP processing. This program presents an image of pop, rock, or jazz live concert. The
sound field reproduces the spaciousness of a massive pavilion with an emphasis on the vividness of
vocals on the stage and solo instruments and the beats of rhythm instruments.
Hall
HiFi DSP processing. This sound field is suitable for classic and orchestral music. The program
uses data collected in a large concert hall in Munich. You can enjoy delicate and beautiful
reverberation and a majestic atmosphere.
Jazz
HiFi DSP processing. The sound field is suitable for jazz and fusion music. It uses data collected in
a famous jazz club in New York. You can enjoy clear reverberation.
Game
CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play games.
The program lets you feel the depth and three-dimensional surrounding sounds of the field where
you are playing, and offers cinema-like surrounding sound effects for the scenes of movies.
TV Sports
CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows with
a live sound environment. For sports relays, the voices of commentators and announcers come
clearly from the center; the cheers and atmosphere in the stadium spread around within a
comfortable range, and you can feel like as if you are in the stadium.
Movie Spacious
CINEMA DSP processing. The sound field is suitable for movies with an emphasis on spectacular
sound effects, and is a perfect fit with a wide screen. The program reproduces a wide dynamic
range from minimum sound effects to powerful sounds.
Movie Dramatic
CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on threedimensional sound effects. It restrains reverberation to an moderate extent, but reproduces sound
effects and background music in a soft, three-dimensional manner with clarity and center
orientation of voices as pivots.
2ch Stereo
Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.
5ch Stereo
HiFi DSP processing. Using this program increases the listening position range. This is a sound
field suitable for background music at parties.
Music Enh. 2ch
Music Enh. 5ch
Select these programs to play back compression artifacts (such as the MP3 format) in
2-channel or 5-channel stereo. This program enhances your listening experience by regenerating
the missing harmonics in a compression artifact.
ENTERTAIN
MOVIE
STEREO
ENHANCER
Features
BASIC
OPERATION
Category
Note
The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the
actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from each
direction.
English
37 En
Sound field programs
■ Enjoying 2-channel sources using the
standard decoders
Signals input from 2-channel sources can also be played
back on multi-channels.
Press D AMP and then press K SUR. DECODE
repeatedly to select a decoder.
You can select from the following decoders depending on
the type of source you are playing and your personal
preference.
STANDARD
Functions
PRO LOGIC
Dolby Pro Logic processing for any
sources
PLII Movie
Dolby Pro Logic II processing for
movie sources
PLII Music
Dolby Pro Logic II processing for
music sources
PLII Game
Dolby Pro Logic II processing for
game sources
■ Using sound field programs without
surround speakers
(Virtual CINEMA DSP)
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers by creating
virtual speakers.
If you set “SUR. L/R SP” to “NONE” (see page 49),
Virtual CINEMA DSP activates automatically whenever
you select a CINEMA DSP or HiFi DSP program (see
page 37).
Note
Virtual CINEMA DSP will not activate even when “SUR. L/R
SP” is set to “NONE” (see page 49) in the following cases:
– When “5ch Stereo” (see page 37) is selected.
– When headphones are connected to the PHONES jack.
38 En
■ Enjoying multi-channel sources and
sound field programs with headphones
(SILENT CINEMA)
SILENT CINEMA allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
sources, through ordinary headphones. SILENT CINEMA
activates automatically whenever you connect headphones
to the PHONES jack while listening to CINEMA DSP or
HiFi DSP sound field programs (see page 37). When
activated, the SILENT CINEMA indicator lights up in the
front panel display.
Note
SILENT CINEMA does not activate when the component
connected to the MULTI CH INPUT jacks is selected as the input
source (see page 33).
■ Enjoying unprocessed input sources
(Straight decoding mode)
When this unit is in the “STRAIGHT” mode, multichannel sources are decoded straight into the appropriate
channels without any additional effect processing. 2channel stereo sources are output from only the front left
and right speakers.
Press B STRAIGHT (or press D AMP and then
press T STRAIGHT) to select “STRAIGHT”.
To deactivate the “STRAIGHT” mode, press
B STRAIGHT (or T STRAIGHT) again so that
“STRAIGHT” disappears from the front panel display.
Sound field programs
■ Editing sound fields parameters
You can enjoy good quality sound with the factory preset
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
1
While listening to a source, press D AMP
and then press Gk / n to select the desired
parameter.
2
Press G l / h to change the parameter
value.
Note
You cannot change parameter values when “MEMORY GUARD”
in “OPTION MENU” is set to “ON” (see page 55).
y
Initial settings are indicated in bold under each parameter.
BASIC
OPERATION
For Pop/Rock, Hall, Jazz, Game, TV Sports,
Movie Spacious and Movie Dramatic:
DSP level DSP LEVEL
Function:
Adjusts the effect level.
Choices:
MIN, MID, MAX
For PRO LOGIC II Music:
Panorama PANORAMA
Function:
Sends stereo signals to the surround
speakers as well as the front speakers for
a wraparound effect.
Choices:
OFF, ON
Dimension DIMENSION
Function:
Gradually adjusts the sound field either
towards the front or towards the rear.
Control range: –3 (towards the rear) to +3 (towards the
front), initial setting is STD (standard).
Center width CT WIDTH
Function:
Adjusts the center image from all three
front speakers to varying degrees. A
larger value adjusts the center image
towards the front left and right speakers.
Control range: 0 (center channel sound is output only
from center speaker) to 7 (center channel
sound is output only from front left and
right speakers), initial setting is 3.
For Music Enh. 2ch and Music Enh. 5ch
Effect level
Function:
Adjusts the effect level.
Choices:
LOW, HIGH
English
39 En
FM/AM TUNING
FM/AM tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations.
Automatic tuning
Manual tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
1
Press D INPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
2
Press 3 FM/AM to select the reception band
(FM or AM).
3
Press 7 TUNING AUTO/MAN’L so that the
AUTO indicator lights up in the front panel
display.
Lights up
If the signal received from the station you want to select is
weak, tune into it manually.
Note
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
1
Press D INPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
2
Press 3 FM/AM to select the reception band
(FM or AM).
3
Press 7 TUNING AUTO/MAN’L so that the
AUTO indicator disappears from the front
panel display.
AUTO
A
AM 1440 kHz
No colon (:)
A
If a colon (:) appears in the front panel display,
automatic tuning is not possible. Press 2 PRESET/
TUNING to turn the colon (:) off.
4
Press 5 PRESET/TUNING l / h once to
begin automatic tuning.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the received
station is shown in the front panel display.
Lights up
AM 1440 kHz
No colon (:)
If a colon (:) appears in the front panel display,
manual tuning is not possible. Press 2 PRESET/
TUNING to turn the colon (:) off.
4
Press 5 PRESET/TUNING l / h to tune
into the desired station manually.
y
Hold down the button to continue searching.
AUTO TUNED
A
40 En
AM 1530 kHz
FM/AM tuning
Automatic preset tuning
Manual preset tuning
You can use the automatic preset tuning feature to store
FM stations with strong signals up to 40 (A1 to E8: 8
preset station numbers in each of the 5 preset station
groups) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
1
2
3
Press D INPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
Press 3 FM/AM to select “FM” as the
reception band.
You can also store up to 40 stations (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups)
manually.
Tune into a station automatically or manually.
See page 40 for tuning instructions.
2
Press 6 MEMORY.
The MEMORY indicator flashes in the front panel
display for approximately 10 seconds.
3
Press 4 A/B/C/D/E and 5 PRESET/
TUNING l / h repeatedly to select a preset
station group (A1 to E8) while the MEMORY
indicator is flashing.
Check that the colon (:) appears in the front panel
display.
Press and hold 6 MEMORY for more than 3
seconds.
The preset station number as well as the MEMORY
and AUTO indicators flashes. After approximately 5
seconds, automatic presetting starts from the current
frequency and proceeds toward the higher
frequencies.
Flashes
TUNED
Flash
AUTO
C3 : AM
Flashes
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
630 kHz
Preset station number
MEMORY
A1:FM 87.5 MHz
MEMORY
BASIC
OPERATION
1
4
Press 6 MEMORY while the MEMORY
indicator is flashing.
The station band and frequency appear in the front
panel display with the preset station group and
number you have selected.
y
You can select the preset station group and the preset station
number where the first received station will be stored by pressing
4 A/B/C/D/E and then 5 PRESET/TUNING l / h.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually
and store it as described in “Manual preset tuning” on this page.
TUNED
C3 : AM
630 kHz
The displayed station has been stored as C3.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
English
41 En
FM/AM tuning
Selecting preset stations
You can tune into any desired station simply by selecting
the preset station group and number under which it was
stored.
y
When performing this operation with the remote control, press
C TUNER to select “TUNER” as the input source.
1
Press 4 A/B/C/D/E (or G A/B/C/D/E l / h)
repeatedly to select the desired preset
station group (A to E).
The preset station group letter appears in the front
panel display and changes each time you press the
button.
Exchanging preset station
You can exchange the assignments of two preset stations
with each other. The example below describes the
procedure to exchange preset station “E1” with “A5”.
1
Select preset station “E1” using 4 A/B/C/D/E
and 5 PRESET/TUNING l / h.
See “Selecting preset stations” on this page.
2
Press and hold 2 PRESET/TUNING for
more than 3 seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
Flashes
2
Press 5 PRESET/TUNING l / h (or
G PRESET/CH k / n) to select the desired
preset station number (1 to 8).
The preset station group and number appear in the
front panel display along with the station band and
frequency.
MEMORY
E1 : FM 87.5 MHz
Flashes
3
E1 : FM 87.5 MHz
y
Select preset station “A5” using 4 A/B/C/D/
E and 5 PRESET/TUNING l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
See “Selecting preset stations” on this page.
You can select the desired preset station number (1 to 8) directly
by pressing the numeric buttons on the remote control.
Flashes
MEMORY
A5 : FM 90.7 MHz
Flashes
4
42 En
Press 2 PRESET/TUNING again.
“EDIT E1–A5” appears in the front panel display and
the assignments of the two preset stations are
exchanged.
USING A USB MEMORY DEVICE OR A USB PORTABLE AUDIO PLAYER
Using a USB memory device or a USB portable audio player
Use this feature to enjoy WAV (PCM format only), MP3 and WMA files saved on your USB memory device or USB
portable audio player connected to the USB port on the front panel of this unit.
■ Supported USB devices
This unit supports USB mass storage class devices (except
USB hard disk drives) using FAT16 or FAT32 format.
Notes
• Only the first partition (32 GB or less) is displayed in the OSD.
You cannot select files in other partitions.
• Up to 8 levels of directory hierarchy and 500 music files per
directory are recognized.
• Some devices may not work properly even if they meet the
requirements.
• Some WAV, MP3 and WMA files may not be playable or may
be noisy when played.
Playback operation
Follow the procedures below to enjoy the music stored in
your USB device or a USB portable audio player.
1
Press D INPUT l / h repeatedly (or press
C USB) to select USB.
The cursor on the left of the USB indicator lights up
in the front panel display, and the contents previously
played is automatically played.
Lights up
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
BASIC
OPERATION
■ Connecting a USB memory device or a
USB potable audio player
CD
USB
INPUT:USB
Connect a USB jack of a USB memory device or
USB portable audio player to the USB port on the
front panel of this unit.
VOLUME
2
Press S DISPLAY to display the top USB file
list.
The USB file list appears in the OSD.
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING
FM/AM
l
A/B/C/D/E
PRESET/TUNING
h
MEMORY
TUNING AUTO/MAN'L
USB
Root
Ellis Margellis
Frankie Zipper
Hall in Call
Jackie Pastarius
Jmiel
Jean-Luc Ponta
Jim Hallo
SCENE
1
l
PHONES
SILENT CINEMA
SPEAKERS
A/B/OFF
TONE CONTROL
PROGRAM
2
3
STRAIGHT
DIRECT STEREO
h
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
USB
R
EFFECT
USB
>
>
>
>
>
>
>
1/7
y
USB memory device
or USB portable
audio player
• “i” in the right corner of each menu line indicates that
there is a submenu available in the next menu level.
• When this unit is in the top directory, “Root” appears
beside “USB”.
English
43 En
Using a USB memory device or a USB portable audio player
3
4
Press G k / n / l / h on the remote control
to select the desired file.
• Press G k / n to select the desired file/folder.
• Press G ENTER or G h to enter the selected
folder.
• Press G l to return to the previous folder level.
■ The function of the play information
display
USB
Press G ENTER to play the selected file.
y
• You can use I b / a to skip backward/forward and
I h / s to start/stop playback independently from the menu
in the OSD.
• You can set the settings for repeat and shuffle mode by using the
“USB PLAY STYLE” parameters in “OPTION MENU” (see
page 55).
• You can select the display mode in the front panel display by
using “FL SCROLL” in “OPTION MENU” (see page 54).
[Play]
1
2
3
.
4
00:00
All
FrankieZipper
Made-to-orderaaaaaAA
;RoadtoIndiaaaAAAA
5
6
7
.A
1 Name of the artist
2 Name of the album
3 Name of the song
4 Elapsed time
Note
When the elapsed time exceed “99:59”, “--:--” appeared
instead of the time.
5
6
(playback) icon
All
(all repeat),
1
(single repeat) icons
When “REPEAT” of the “USB PLAY STYLE” in “OPTION
MENU” (see page 55) is set to “OFF”, no icon appears in the
top right corner while files or folders are being played.
7
(shuffle) icon
When “SHUFFLE” of the “USB PLAY STYLE” in
“OPTION MENU” (see page 55) is set to “OFF”, no icon
appears in the top right corner while files or holders are being
played.
44 En
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
Notes
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
1
Turn on all the connected components.
2
Press D INPUT l / h repeatedly (or press
one of the input selector buttons (C)) to
select the source component you want to
record from.
3
Start playback on the selected source
component or select a broadcast station.
4
Start recording on the recording component.
BASIC
OPERATION
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• TONE CONTROL (see page 34) and VOLUME settings, speaker levels (see page 34) and the sound field programs (see page 37) do
not affect recorded material.
• The source connected to the USB jack or the MULTI CH INPUT jacks of this unit cannot be recorded.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if
your source component is connected to provide only digital signals, you cannot record the source.
• S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing
video signals input from a video source component that provides only an S-video or a composite video signal, you can record only an
S-video or a composite video signal on your DVD recorder.
• A given input source is not output on the same OUT (REC) channel.
• Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is
turned off, this unit may distort the sound from other components.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
English
45 En
SET MENU
SET MENU
You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ Auto setup AUTO SETUP
Use this feature to automatically adjust speaker and system parameters (see page 24).
■ Manual setup MANUAL SETUP
Use this feature to manually adjust speaker and system parameters.
Sound menu 1 SOUND MENU
Use this menu to manually adjust any speaker settings, alter the quality and tone of the sound output by the system or
compensate for video signal processing delays when using LCD monitors or projectors.
Parameter
Features
Page
A)SPEAKER SET
Selects the size of each speaker, the speakers for low-frequency signal output, and the
crossover frequency, and the location of the front speakers connected to the FRONT B
terminals.
48
B)SP LEVEL
Adjusts the output level of each speaker.
50
C)SP DISTANCE
Adjusts the distance of each speaker.
50
D)CENTER GEQ
Adjusts the tonal quality of the center speaker.
51
E)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
51
F)D.RANGE
Adjusts the dynamic range of Dolby Digital or DTS signals.
51
G)AUDIO SET
Adjusts the muting level, audio delay, maximum volume level and initial volume level.
51
Input menu 2 INPUT MENU
Use this menu to manually reassign the input jacks, select the input mode or rename the input source.
Parameter
Features
Page
A)INPUT ASSIGN
Assigns the input jacks of this unit according to the component to be used.
52
B)INPUT RENAME
Changes the name of the input source.
53
C)VOLUME TRIM
Adjusts the output volume of each input source.
53
D)DECODER MODE
Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the
rear panel of this unit.
53
E)MULTI CH SET
Selects the video source played in the background of the sources input from the MULTI CH
INPUT jacks.
54
46 En
SET MENU
Option menu 3 OPTION MENU
Use this menu to manually adjust the optional system parameters.
Parameter
Features
Page
A)DISPLAY SET
Adjusts the brightness of the front panel display.
54
B)MEMORY GUARD
Locks sound field program parameters and other “SET MENU” settings.
55
C)AUDIO SELECT
Designates the default audio input jack select setting for the input sources connected to the
DIGITAL INPUT jacks when you turn on the power of this unit.
55
D)PARAM. INI
Sets all the parameters of the sound field programs to the factory settings.
55
E)USB PLAY STYLE
Adjusts the playback style of a USB source.
55
■ Signal information SIGNAL INFO
Use this feature to check audio signal information (see page 35).
Using SET MENU
3
Use the remote control to access and adjust each
parameter.
y
;MANUAL SETUP
You can change the “SET MENU” parameters while this unit is
reproducing sound.
. 1 SOUND MENU
2 INPUT MENU
3 OPTION MENU
Press D AMP and then press Q MENU to
enter “SET MENU”.
The top “SET MENU” display appears in the OSD.
4
Press G k / n / l / h and G ENTER to select
and change the parameter.
• Press G k / n to select the desired menu or
parameter.
• Press G l / h to change the parameter value.
• Press G ENTER to enter the selected menu or to
confirm the parameter.
• Press H RETURN to return to the previous menu
level.
5
Press Q MENU to exit from “SET MENU”.
TOPAMENU
. ;AUTO SETUP
.A;MANUAL SETUP
;SIGNAL INFO
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
2
Press G k / n to select “MANUAL SETUP”.
SET MENU
p
p
SET MENU
[ ]/[ ]:Up/Down
[ENTER]:Enter
ADVANCED
OPERATION
1
Press G ENTER to enter “MANUAL SETUP”.
The “MANUAL SETUP” display appears in the
OSD.
TOPAMENU
;AUTO SETUP
.A;MANUAL SETUP
;SIGNAL INFO
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
English
47 En
SET MENU
1 SOUND MENU
Use this menu to manually adjust any speaker settings or
compensate for video signal processing delays.
;MANUAL SETUP
;MANUAL SETUP
1 SOUND MENU
1/2
1 SOUND MENU
2/2
Front speakers FRONT SP
Choices: SMALL, LARGE
. F)D.RANGE
G)AUDIO SET
1 SOUND MENU
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
p
. A)SPEAKER SET
B)SP LEVEL
C)SP DISTANCE
D)CENTER GEQ
E)LFE LEVEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
Woofer section of a speaker is 16 cm (6.5 in) or larger:
large
Woofer section of a speaker is smaller than 16 cm
(6.5 in): small
A)SPEAKER SET
FRONT SP
■ Speaker settings A)SPEAKER SET
Use this feature to manually adjust any speaker settings.
FRONT B speaker setting FRONT B
Use this feature to select the location of the front speakers
connected to the FRONT B terminals.
Choices: FRONT, ZONE B
SMALL
>LARGE
When the front speakers are large
Select “LARGE” (large).
When the front speakers are small
Select “SMALL” (small).
1 SOUND MENU
A)SPEAKER SET
FRONT B;;;;FRONT
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Select
• Select “FRONT” to turn on or off SPEAKERS A and B
when the speakers connected to the FRONT B
terminals are set in the main zone.
• Select “ZONE B” if the speakers connected to the
FRONT B terminals are set in another zone. If
SPEAKERS A is turned off and SPEAKERS B is
turned on, all the speakers including the subwoofer in
the main zone are muted and this unit outputs sound at
the FRONT B terminals only.
Note
When “LFE/BASS OUT” is set to “FRONT” (see page 49), you
can select only “LARGE” in “FRONT SP”. If the value of
“FRONT SP” is set to a setting other than “LARGE” in advance,
this unit automatically changes the value to “LARGE”.
Center speaker CENTER SP
Choices: NONE, SML, LRG
1 SOUND MENU
A)SPEAKER SET
CENTER SP
NONE >SML
LRG
Notes
• If you connect headphones to the PHONES jack of this unit, the
sound is output from both headphones and the FRONT B
terminals when “FRONT B” is set to “ZONE B”.
• If a DSP program is selected when “FRONT B” is set to
“ZONE B”, this unit automatically enters the Virtual CINEMA
DSP mode (see page 38).
48 En
When the center speaker is large
Select “LRG” (large).
When the center speaker is small
Select “SML” (small).
When you do not use the center speaker
Select “NONE” (none). The center channel signals are
directed to the front left and right speakers.
SET MENU
Surround left/right speakers SUR. L/R SP
Choices: NONE, SML, LRG
1 SOUND MENU
A)SPEAKER SET
SUR. L/R SP
NONE >SML
Crossover CROSSOVER
Use this feature to select a crossover frequency of all the
speakers set to “SML” (or “SMALL”) or to “NONE” in
“SPEAKER SET” (see pages 47 and 48). All frequencies
below the selected frequency will be sent to the subwoofer
or to the speakers set to “LRG” (or “LARGE”) in
“SPEAKER SET” (see pages 47 and 48).
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
LRG
1 SOUND MENU
When the surround speakers are large
Select “LRG” (large).
When the surround speakers are small
Select “SML” (small).
When you do not use the surround speakers
Select “NONE” (none). This unit is set to the Virtual
CINEMA DSP mode (see page 38).
LFE Bass out LFE/BASS OUT
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
Choices: SWFR, FRONT, BOTH
A)SPEAKER SET
CROSSOVER
FREQ;;;80Hz
Subwoofer phase SUBWOOFER PHASE
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
Choices: NORMAL, REVERSE
1 SOUND MENU
A)SPEAKER SET
SUBWOOFER PHASE
1 SOUND MENU
SWFR FRONT>BOTH
>NORMAL
REVERSE
• Select “NORMAL” if you do not want to reverse the
phase of your subwoofer.
• Select “REVERSE” to reverse the phase of your
subwoofer.
ADVANCED
OPERATION
A)SPEAKER SET
LFE/BASS OUT
When a subwoofer is connected to this unit
and you want to get natural bass sound
Select “SWFR” (subwoofer). The LFE signals as well
as the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are directed to the subwoofer.
When a subwoofer is connected to this unit
and you want to get rich bass sound
Select “BOTH” (both). The low-frequency signals of
any source are output from the subwoofer. The LFE
signals as well as the low-frequency signals of other
speakers set to “SML” (or “SMALL”) are directed to
the subwoofer. The low-frequency signals of the front
left and right channels are directed to the front left and
right speakers and the subwoofer regardless of the
“FRONT SP” setting (see page 48).
English
When you do not use a subwoofer
Select “FRONT” (front). The LFE signals, the lowfrequency signals of the front left and right channels,
and the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are all directed to the front left
and right speakers regardless of the “FRONT SP”
setting (see page 48).
49 En
SET MENU
■ Speaker level B)SP LEVEL
Use this feature to manually adjust the output level of each
speaker.
Control range: –10 to +10 dB
Control step: 1 dB
Initial setting: 0 dB
1 SOUND MENU
.
■ Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
B)SP LEVEL
1/2
-__________+
FL
FR
C
1 SOUND MENU
C)SP DISTANCE
. UNIT;;;;;;;;feet
FRONT L;;;10.0ft
FRONT R;;;10.0ft
CENTER;;;;10.0ft
Adjusted speaker
FL
Front left speaker
FR
Front right speaker
C
Center speaker
SL
Surround left speaker
SR
Surround right speaker
SWFR
Subwoofer
p
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
p
SP LEVEL
1/2
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting: feet (ft)
• Select “feet” to adjust speaker distances in feet.
• Select “meters” to adjust speaker distances in meters.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting: 3.00 m (10.0 ft)
Note
The available speaker channels differ depending on the setting of
the speakers.
SP DISTANCE
Adjusted speaker
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SUR. L
Surround left speaker
SUR. R
Surround right speaker
SWFR
Subwoofer
Note
The available speaker channels differ depending on the setting of
the speakers.
50 En
SET MENU
■ Center speaker equalizer D)CENTER GEQ
■ Dynamic range F)D.RANGE
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
Test tone TEST
Use this feature to make adjustments for “CENTER GEQ”
while listening to a test tone.
Choices: OFF, ON
• Select “OFF” to stop test tones and output the currently
selected source component.
• Select “ON” to output test tones from the center and
front left speakers.
E)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
Speaker SPEAKER
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Choices: MIN, STD, MAX
• Select “MIN” (minimum) if you regularly listen at low
volume levels.
• Select “STD” (standard) for general use.
• Select “MAX” (maximum) to preserve the greatest
amount of dynamic range.
■ Audio settings G)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
1 SOUND MENU
G)AUDIO SET
. MUTE TYPE;;;FULL
A.DELAY;;;;;;0ms
MAX VOL.;;;+16dB
INI.VOL.;;;;;OFF
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
p
1 SOUND MENU
Headphone HP
Adjusts the headphone compression.
p
Use this feature to adjust the output level of the LFE (lowfrequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to 0 dB
Control step: 1 dB
Speaker SP
Adjusts the speaker compression.
ADVANCED
OPERATION
■ Low-frequency effect level E)LFE LEVEL
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
p
p
p
D)CENTER GEQ
TEST >OFF ON
. 100Hz ;;;;;;
0.0dB
300Hz ;;;;;;
0.0dB
1kHz ;;;;;;
0.0dB
3kHz ;;;;;;
0.0dB
10kHz ;;;;;;
0.0dB
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
F)D.RANGE
. SP D.R;;;;MAX
HP D.R;;;;MAX
p
1 SOUND MENU
1 SOUND MENU
Mute type MUTE TYPE
Use this feature to adjust how much the mute function
reduces the output volume (see page 36).
Choices: FULL, –20dB
• Select “FULL” to completely mute all the audio
output.
• Select “–20dB” to reduce the current volume by 20 dB.
Audio delay A.DELAY
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 160 ms
Control step: 1 ms
Note
English
Depending on the settings of “LFE/BASS OUT” (see page 49),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
51 En
SET MENU
Maximum volume MAX VOL.
Use this feature to set the maximum volume level. This
feature is useful to avoid the unexpected loud sound by
mistake. For example, the original volume range is 16 dB
to –80 dB. However, when “MAX VOL.” is set to –5 dB,
the volume range becomes –5.0 dB to –80.0 dB.
2 INPUT MENU
Use this menu to reassign the input jacks, select the
decoder mode or rename the input source.
;MANUAL SETUP
Control range: 16 dB, 10 dB to –30 dB
Control step: 5 dB
2 INPUT MENU
Note
Initial volume INI.VOL.
Use this feature to set the volume level when the power of
this unit is turned on.
Choices: OFF, –80 dB to +16 dB
Control step: 1 dB
Note
The “MAX VOL.” setting takes priority over the “INI.VOL.”
setting.
p
The “MAX VOL.” setting takes priority over the “INI.VOL.”
setting. For example, if “INI.VOL.” is set to –20 dB and “MAX
VOL.” is set to –30 dB, the volume level is automatically set to
–30 dB when you turn on the power of this unit next time.
p
. A)INPUT ASSIGN
B)INPUT RENAME
C)VOLUME TRIM
D)DECODER MODE
E)MULTI CH SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Input assignment
A)INPUT ASSIGN
Use this feature to assign the input jacks according to the
component to be used if the initial settings of this unit do
not correspond to your needs. Change the following
parameters to reassign the respective jacks and effectively
connect more components.
Once the input jacks are reassigned, you can select the
corresponding component by using D INPUT l / h (or
the input selector buttons (C)).
For COAXIAL INPUT jack 1
COAXIAL IN (1)
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
2 INPUT MENU
A)INPUT ASSIGN
COAXIAL IN
. (1);;;;;
(
DVD
DVD
)
[p]/[[]:Select
For OPTICAL INPUT jacks 2 and 3
OPTICAL IN (2)
OPTICAL IN (3)
Choices: (2) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
(3) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
2 INPUT MENU
A)INPUT ASSIGN
OPTICAL IN
. (2);;;;;DTV/CBL
(DTV/CBL )
(3);;;;;
CD
(
CD
)
[p]/[[]:Select
Note
You cannot select a specific item more than once.
52 En
SET MENU
■ Input rename B)INPUT RENAME
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
2 INPUT MENU
B)INPUT RENAME
DVD ->
DVD
p
1
p
[p]/[[]:Position
[ ]/[ ]:Chara.
Press one of the input selector buttons (C)
or A MULTI CH IN to select the input
source you want to change the name of.
■ Volume trim C)VOLUME TRIM
Use this feature to adjust the output volume of each
source. This is useful if you want to balance the level of
each input source to avoid sudden changes in volume
when switching between input sources.
Choices: CD, MD/CD-R, TUNER, DVD,
DTV/CBL, V-AUX, DVR, USB,
MULTI CH IN
Control range: –6.0 to +6.0 dB
Control step: 1.0 dB
Initial setting: 0.0 dB
2 INPUT MENU
C)VOLUME TRIM
DVD
DVD ;;;;;;0.0dB
MULTI CH IN
[p]/[[]:Adjust
[RETURN]:Exit
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX
■ Decoder mode D)DECODER MODE
USB
2 INPUT MENU
D)DECODER MODE
2
4
Repeat steps 1 through 3 to rename each
input source.
5
Press G ENTER to exit from “INPUT
RENAME”.
[ ]/[ ]:Up/Down
[p]/[[]:Select
Decoder select mode
Use this feature to designate the default decoder mode for
the input sources connected to the DIGITAL INPUT jacks
when you turn on the power of this unit.
Choices: AUTO, LAST
ADVANCED
OPERATION
Notes
• You can use up to 8 characters for each input.
• Press G n to change the character in the following order,
or press G k to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#,
*, –, +, etc.)
LAST
;;;;AUTO
;;;;AUTO
;;;;AUTO
p
Press G k / n to select the character you
want to use and then press G l / h to move
to the next space.
>AUTO
CD
DVD
DTV/CBL
p
3
Press D AMP and then press G l / h on the
remote control to place the “_” (underscore)
under the space or the character you want to
edit.
.
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate decoder mode.
• Select “LAST” if you want this unit to automatically
select the last decoder mode used the connected input
source.
DTS decoder prioritize setting
Choices: AUTO, DTS
• Select “AUTO” if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
• Select “DTS” when you play back a DTS-CD.
English
53 En
SET MENU
■ Multi channel input setup
E)MULTI CH SET
2 INPUT MENU
E)MULTI CH SET
BGV;;;;;;;;;LAST
[p]/[[]:Select
Background Video BGV
Use this feature to select the video source played in the
background of the sources input at the MULTI CH INPUT
jacks.
Choices: DVD, DTV/CBL, V-AUX, DVR, LAST
y
Select “LAST” to set this unit to automatically select the last
selected video source as the background video source.
3 OPTION MENU
Use this menu to adjust the optional system parameters.
;MANUAL SETUP
3 OPTION MENU
p
p
. A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI
E)USB PLAY STYLE
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Display settings A)DISPLAY SET
3 OPTION MENU
A)DISPLAY SET
p
p
. DIMMER;;;;;;;;;0
FL SCROLL;;;CONT
OSD SHIFT;;;;;;0
OSD-SOURCE;;;30s
OSD-AMP;;;;;;30s
[ ]/[ ]:Up/Down
[p]/[[]:Select
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: – 4 to 0
Control step: 1
• Press G l to make the front panel display dimmer.
• Press G h to make the front panel display brighter.
54 En
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as a song title or a channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when “USB” is selected as the input source.
Choices: CONT, ONCE
• Select “CONT” to display the operation status in the
front panel display in a continuous manner.
• Select “ONCE” to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (upward) to +5 (downward)
Control step: 1
Initial setting: 0
• Press G l to raise the position of the OSD.
• Press G h to lower the position of the OSD.
Source feature OSD display time
OSD-SOURCE
Use this feature to set the amount of time to display the
USB file list and the play information in the OSD after
you perform a certain operation.
Choices: ON, 10s, 30s
• Select “ON” to display the OSD continuously during
an operation.
• Select “10s” to turn off the OSD 10 seconds after you
perform a certain operation.
• Select “30s” to turn off the OSD 30 seconds after you
perform a certain operation.
Amplifier function OSD display time
OSD-AMP
Use this feature to set the amount of time to display the
status and sound field parameters information screen after
you perform a certain operation.
Choices: ON, 10s, 30s
• Select “ON” to display the OSD constantly during an
operation.
• Select “10s” to turn off the OSD 10 seconds after you
perform a certain operation.
• Select “30s” to turn off the OSD 30 seconds after you
perform a certain operation.
SET MENU
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
■ Parameter initialization D)PARAM. INI
Use this feature to set all the parameters of the sound field
programs to the initial factory settings.
Choices: NO, YES
3 OPTION MENU
3 OPTION MENU
B)MEMORY
>OFF
D)PARAM. INI
GUARD
>NO
ON
[p]/[[]:Select
[ENTER]:Return
[p]/[[]:Select
• Select “OFF” to turn off the “MEMORY GUARD”
feature.
• Select “ON” to protect:
– sound field program parameters
– all “SET MENU” items
– all speaker levels
– SCENE template parameters
Note
When “MEMORY GUARD” is set to “ON”, you cannot select
and adjust any other “SET MENU” items.
■ Audio select
3 OPTION MENU
C)AUDIO SELECT
>AUTO
LAST
• You cannot automatically revert to the previous parameter
settings once you initialize the sound field program parameters.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any sound field program groups when
“MEMORY GUARD” is set to “ON”.
■ USB playback styles E)USB PLAY STYLE
Use this feature to adjust the playback style according to
your preference. You can shuffle files in a random order or
repeat one specific file or a sequence of files.
3 OPTION MENU
E)USB PLAY STYLE
. REPEAT.......OFF
SHUFFLE......OFF
[ ]/[ ]:Up/Down
[p]/[[]:Select
p
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate input mode.
• Select “LAST” if you want this unit to automatically
select the last input mode used for the connected input
source (see page 33).
Notes
p
[p]/[[]:Select
• Select “NO” to cancel the parameter initialization and
return to the previous menu screen.
• Select “YES” and then press G ENTER to set all the
sound field parameters to the initial factory settings.
ADVANCED
OPERATION
C)AUDIO SELECT
Use this feature to designate the default audio input jack
select setting for the input sources when you turn on the
power of this unit.
Choices: AUTO, LAST
YES
Repeat REPEAT
Use this feature to set this unit to repeat one file or a
sequence of files.
Choices: OFF, SINGLE, ALL
• Select “OFF” to deactivate this feature.
• Select “SINGLE” to set this unit to repeat one file.
• Select “ALL” to set this unit to repeat a sequence of
files.
Shuffle SHUFFLE
Use this feature to set this unit to play files or folders in a
random order.
Choices: OFF, ON
• Select “OFF” to deactivate this feature.
• Select “ON” to set this unit to play files or folders in a
random order.
English
55 En
Remote control features
Remote control features
In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha
and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code
for each input source (see page 59).
Using remote control on the SCENE feature
■ Controlling the input source
components in the SCENE mode
■ Setting input source of the customized
SCENE template on the remote control
You can operate both this unit and the input source
component by using the remote control. You must set the
appropriate remote control code for each input source in
advance (see page 59).
If you customize the input source of the selected SCENE
template, you must set the input source of the SCENE
template on the remote control to operate the input source
component correctly.
1
Press the desired E SCENE button on the
remote control.
2
Press the desired buttons in the * area below
to control the input source component of the
selected SCENE template.
POWER
POWER
STANDBY
POWER
TV
AV
MULTI CH IN
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
V-AUX
*
TV CH
DVR
USB
AMP
TV INPUT
1
2
TV VOL
TV MUTE
SCENE
BAND LEVEL
TITLE
3
4
SCENE
buttons
VOLUME
MENU
ENTER
DISPLAY
RETURN
REC
FREQ/TEXT
EON
MODE – PTY SEEK – START
l
PROG h
ENHANCER STRAIGHT
1
2
3
SUR.DECODE NIGHT
4
DIRECT ST.
5
6
7
9
0
10
8
ENT
Note
*
These buttons control the input source component. See page 58
for details of the function of each button.
56 En
Press and hold the E SCENE button and the
desired input selector button (C) for 3 seconds.
y
Press the E SCENE button again to operate the input source
component.
Remote control features
Controlling this unit, a TV, or other components
■ Controlling this unit
■ Controlling a TV
Press D AMP to control this unit.
Press C DTV/CBL to control your TV. To control your
TV, you must set the appropriate remote control code for
DTV/CBL (see page 59).
POWER
POWER
STANDBY
POWER
TV
AV
MULTI CH IN
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
POWER
V-AUX
AMP
USB
TV INPUT
AMP
TV CH
TV VOL
TV MUTE
*1
DTV/CBL
SCENE
1
2
BAND LEVEL
TITLE
3
4
POWER
STANDBY
POWER
TV
AV
MULTI CH IN
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
V-AUX
TV CH
DVR
*1
USB
AMP
TV INPUT
1
2
TV VOL
TV MUTE
VOLUME
MENU
SCENE
3
4
ENTER
BAND LEVEL
TITLE
VOLUME
MENU
DISPLAY
RETURN
ENTER
*2
REC
DISPLAY
RETURN
FREQ/TEXT
EON
MODE – PTY SEEK – START
l
PROG h
ENHANCER STRAIGHT
1
2
3
SUR.DECODE NIGHT
*2
4
DIRECT ST.
5
6
7
9
0
10
8
REC
FREQ/TEXT
EON
MODE – PTY SEEK – START
l
PROG h
ENHANCER STRAIGHT
1
2
ENT
3
SUR.DECODE NIGHT
4
DIRECT ST.
5
6
7
9
0
10
8
ENT
ADVANCED
OPERATION
Notes
*1
These buttons always control this unit regardless of the
operation mode selector position.
*2 These buttons control this unit only when D AMP is pressed.
Notes
*1
These buttons always control your TV regardless of whether
you press C DTV/CBL or not.
Remote control
*2
Digital TV/Cable TV
TV POWER
Turns on or off the power.
TV CH +/–
Changes the channel number.
TV VOL +/–
Increases or decreases the volume
level.
TV MUTE
Mutes the audio output.
TV INPUT
Changes the input source.
These buttons control your TV only when the operation mode
selector is set to TV. For details, see the “Digital TV/Cable
TV” column on page 58.
English
57 En
Remote control features
■ Controlling other components
Press one of the input selector buttons (C) or to control
other components. You must set the appropriate remote
control code for each input source in advance (see
page 59). The following table shows the function of each
control button used to control other components assigned
to each input selector button. Be advised that some buttons
may not correctly operate the selected component.
1
POWER
POWER
TV
AV
MULTI CH IN
STANDBY
POWER
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX
AMP
y
4
5
USB
TV INPUT
TV MUTE
1
2
3
4
4
5
6
DVD
player/
recorder
VCR
Digital TV/
LD player
Cable TV
CD player
MD/CD
recorder
AV POWER
Power *1
Power *1
Power *2
Power *1
Power *1
TITLE
Title
VOLUME
MENU
8
DISPLAY
RETURN
REC
EON
MODE – PTY SEEK – START
l
PROG h
ENHANCER STRAIGHT
1
2
3
4
DIRECT ST.
SUR.DECODE NIGHT
5
6
7
9
0
10
Tuner
8
9
ENT
USB
Band
PRESET/CH k Up
VCR channel
up
Up
Preset up (1-8) Up
PRESET/CH n Down
VCR channel
down
Down
Preset down
(1-8)
Down
A/B/C/D/E l Left
Left
Preset down
(A-E)
Previous menu
A/B/C/D/E h Right
Right
Preset up
(A-E)
Subsequent
menu
ENTER
Enter
Enter
Subsequent
menu
RETURN
Return
Return
Previous menu
REC/
DISC SKIP
Disc skip
(player)
Rec
Rec (recorder)
Rec *2
p
Play
Play
Play *2
w
Search
backward
Search
backward
Search
backward *2
f
Search forward Search forward
Search forward
Search forward Search forward Search forward
*2
e
Pause
Pause *2
b
Skip backward
Skip backward Skip backward
Skip backward Skip backward Skip backward
*2
a
Skip forward
Skip forward
Skip forward
*2
Skip forward
Skip forward
Skip forward
Pause
Disc skip
Rec
Play
Play
Play
Search
backward
Search
backward
Search
backward
Pause
Pause
Play
Pause
s
Stop
Stop
Stop *2
Stop
Stop
Stop
6
1-9, 0, +10
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
Numeric
buttons
7
8
9
MENU
Menu
DISPLAY
Display
Display
Display
Display
Display
Display
ENT
Title/Index
Enter
Enter
Chapter/Time
Index
Index
Skip backward
Skip forward
Stop
Preset stations
(1-8)
Menu
Display
Notes
*1
*2
7
ENTER
FREQ/TEXT
Remote
control
Power *1
BAND LEVEL
TITLE
3
TV VOL
SCENE
The remote control has 10 modes (input areas) to control
components so that the remote control can operate up to 10
different components.
1
2
3
TV CH
2
This button is operational only when the original remote control supplied with the component has a POWER button.
These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 59).
58 En
Remote control features
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
While pressing and holding one of the input
selector buttons (C) on the remote control to
select the input area you want to set up,
press AV POWER for more than 3 seconds.
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
Remote control code default settings
Input
source
Component
category
Manufacturer
CD
CD
YAMAHA
5013
MD/CD-R
CD-R
YAMAHA
5001
DVD
DVD
YAMAHA
2000
DTV/CBL
–
–
–
TUNER
TUNER
YAMAHA
5007
V-AUX
–
–
–
USB
USB
YAMAHA
5012
DVR
DVR
YAMAHA
2011
–
–
–
POWER
AV
Default
code
V-AUX
USB
While holding down
2
Press for 3 seconds
Press the numeric buttons (0 to 9) (W) to
enter the four-digit remote control code for
the component to be used.
Notes
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• If you do not press any buttons within 30 seconds in step 2, the
setup process is canceled. If this happens, repeat the setup
procedure.
ADVANCED
OPERATION
Note
You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case,
try setting another Yamaha remote control code.
English
59 En
Advanced setup
Advanced setup
This unit has additional menus that are displayed in the
front panel display. The advanced setup menu offers
additional operations to adjust and customize the way this
unit operates. Change the initial settings (indicated in bold
under each parameter) to reflect the needs of your
listening environment.
Notes
• Only 1 STANDBY/ON and B STRAIGHT are effective while
you are using the advanced setup menu.
• No other operations can be made while you are using the
advanced setup menu.
• The advanced setup menu is only available in the front panel
display.
■ Speaker impedance SP IMP.
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices: 8Ω MIN, 6Ω MIN
• Select “8Ω MIN” to set the speaker impedance to 8 Ω .
• Select “6Ω MIN” to set the speaker impedance to 6 Ω .
SP IMP.
Speaker
Impedance level
Front (A or B)
8Ω MIN
Center
The impedance of each
speaker must be 8 Ω or
higher.
Surround
Front (A or B)
1
Press 1 STANDBY/ON on the front panel to
set this unit to the standby mode.
2
Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this
unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
6Ω MIN
Center
The impedance of each
speaker must be 6 Ω or
higher.
Surround
3
Press B STRAIGHT repeatedly to change
the selected parameter setting.
4
Press 1 STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
■ Factory presets PRESET
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 67).
Choices: CANCEL, RESET
• Select “CANCEL” not to reset any parameters of this
unit.
• Select “RESET” to reset the parameters of this unit.
Notes
y
The settings you made are reflected next time you turn on this
unit.
60 En
• This setting completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
Troubleshooting
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
No sound
Cause
Remedy
See
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
12
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-20
No appropriate Audio input jack select has
been set.
Set an appropriate Audio input jack select.
No appropriate input source has been
selected.
Select an appropriate input source with D INPUT
l / h on the front panel (or the input selector
buttons (C) on the remote control).
Speaker connections are not secure.
Secure the connections.
12
The front speakers to be used have not
been selected properly.
Select the front speakers with 9 SPEAKERS on the
front panel.
33
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press O MUTE or R VOLUME +/– on the remote
control to resume audio output and then adjust the
volume.
36
—
13
33
32, 33
Play a source whose signals can be reproduced by this
unit.
Audio signals input at the HDMI jack are
not output from any speaker terminals.
Make an analog or digital connection beside the
HDMI connection.
—
The setting of the connected component is
improper.
Make an appropriate setting following the instruction
manual of the connected component.
—
—
ADDITIONAL
INFORMATION
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
English
61 En
Troubleshooting
Problem
The sound suddenly
goes off.
Cause
See
page
Check that the impedance setting is correct.
13
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
Turn on this unit, and play the source again.
—
The sound is muted.
Press O MUTE or R VOLUME +/– on the remote
control to resume audio output.
36
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-20
Incorrect settings in “SP LEVEL”.
Adjust the “SP LEVEL” settings.
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
This is not malfunction.
No sound is heard
from the center
speaker.
“CENTER” in “SET MENU” is set to
“NONE”.
Set “CENTER” to “SML” or “LRG”.
One of the HiFi DSP programs (except for
5ch Stereo) has been selected.
Try another sound field program.
“SUR. L/R SP” in “SPEAKER SET” is
set to “NONE”.
Set “SUR. L/R SP” to “SML” or “LRG”.
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press B STRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel
display.
“LFE/BASS OUT” in “SPEAKER SET”
is set to “FRONT” when a Dolby Digital
or DTS signal is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
“LFE/BASS OUT” in “SPEAKER SET”
is set to “SWFR” or “FRONT” when a 2channel source is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
The source does not contain lowfrequency bass signals.
This is not malfunction.
No sound is heard
from the surround
speakers.
No sound is heard
from the subwoofer.
62 En
The protection circuitry has been activated
because of a short circuit, etc.
Remedy
34
—
48
37
49
38
49
49
—
Troubleshooting
Problem
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
Cause
Remedy
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
Audio input jack select is set to
“ANALOG”.
Set Audio input jack select to “AUTO”.
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
The volume level
cannot be increased,
or the sound is
distorted.
You are attempting to set the volume level
higher than the maximum volume level.
Adjust “MAX VOL.” setting.
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
This is not malfunction.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
Connect the source component to the analog AUDIO
IN jacks.
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“MEMORY GUARD” in “OPTION
MENU” is set to “ON”.
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This is not malfunction.
This unit suddenly
enters the standby
mode.
The internal temperature is too high and
the overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
See
page
—
33
—
52
—
—
16, 19
Set “MEMORY GUARD” to “OFF”.
55
—
—
ADDITIONAL
INFORMATION
12
—
—
English
63 En
Troubleshooting
■ Tuner
Problem
FM stereo reception is
noisy.
FM
AM
Cause
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Remedy
See
page
Check the antenna connections.
20
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
40
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Previously preset
stations can no longer
be tuned into.
This unit has been disconnected for a
long period.
Set preset stations.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
—
Use the manual tuning method.
40
There are continuous
crackling and hissing
noises.
Noise can result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV set.
Adjust the antenna position to eliminate
multi-path interference.
Use a high-quality directional FM antenna.
Use the manual tuning method.
—
—
40
41
—
■ AUTO SETUP
Before AUTO SETUP
Error message
Connect MIC!
Unplug HP!
64 En
Cause
Optimizer microphone is not connected.
Headphones are connected.
Remedy
See
page
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
24
Unplug the headphones.
—
Troubleshooting
During AUTO SETUP
Error message
Cause
Remedy
See
page
E-1:NO FRONT SP
Front L/R channel signals are not detected.
Check the front L/R speaker connections.
12
E-2:NO SUR.SP
A surround channel signal is not detected.
Check the surround speaker connections.
12
E-3:NOISY
Background noise is too loud.
Try running “AUTO SETUP” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
The optimizer microphone was unplugged
during the “AUTO SETUP” procedure.
Connect the supplied optimizer microphone
to OPTIMIZER MIC jack on the front
panel.
24
E-5:USER CANCEL
The “AUTO SETUP” procedure was
cancelled due to user activity.
Run “AUTO SETUP” again.
E-6:INTERNAL ERROR
An internal error occurred.
Run “AUTO SETUP” again.
E-4:NO MIC
24
24
After AUTO SETUP
Warning message
W-1:OUT OF PHASE
W-2:OVER 24m (80ft)
W-3:LEVEL ERROR
Cause
Remedy
See
page
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the speaker connections for proper
polarity (+ or –).
The distance between the nearest speaker
and the furthest speaker is out of adjustable
range.
Bring the speaker closer to the listening
position.
The difference of volume level among
speakers is excessive. (No level correction
is made.)
If “SWFR:TOO LOUD” or “SWFR:TOO
LOW” appears, adjust the output volume of
the subwoofer.
24
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections.
12
Use speakers of similar quality.
—
12
—
ADDITIONAL
INFORMATION
Notes
•
•
•
•
If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
If a warning message “W-1” appears, corrections are made, but they may not be optimal.
If a warning message “W-2” or “W-3” appears, no corrections are made.
If an error message “E-6” occurs repeatedly, please contact a qualified Yamaha service center.
English
65 En
Troubleshooting
■ USB
Cause
The music files and
directories in the USB
device cannot be
viewed.
The music files and directories are placed
in locations other than the FAT area.
Place music files and directories in the FAT area.
You are attempting to browse directory
hierarchies of over 8 levels or a directory
with more than 500 files.
Modify the data structure on your USB device.
The USB device
cannot be recognized.
The connected USB device is other than a
USB mass storage class USB memory
device or USB portable audio player.
This unit can recognize only a USB mass storage
class USB memory device (except USB hard disk
drives) or USB portable audio player. Also note that it
cannot recognize certain USB devices even when they
are devices as described above.
43
Some devices may become easier to recognize when
they are inserted before turning this unit on.
21
“Disconnected” is
displayed even when
a USB device is
present.
This unit recognized the USB device as an
illegal device.
Status message
Cause
Disconnected
Access error
Unable to play
66 En
Remedy
See
page
Problem
—
—
Turn this unit off then on again.
21
Remedy
See
page
Your USB memory device or USB
portable audio player has been
disconnected from the USB port of this
unit.
Check the connection between this unit and your
USB memory device or USB portable audio player.
There is a problem with the signal path
from your USB memory device or USB
portable audio player to this unit.
Turn off this unit and reconnect your USB memory
device or USB portable audio player to the USB port
of this unit.
43
Try resetting your USB memory device or USB
portable audio player.
—
—
This unit cannot access your USB
memory device or USB portable audio
player.
Try another USB memory device or USB portable
audio player.
There is a problem with the signal path
from your USB memory device or USB
portable audio player to this unit.
Turn off this unit and reconnect your USB memory
device or USB portable audio player to the USB port
of this unit.
43
Try resetting your USB memory device or USB
portable audio player.
—
Try another USB memory device or USB portable
audio player.
—
No varied data is detected.
—
Troubleshooting
■ Remote control
Problem
The remote control
does not work nor
function properly.
Remedy
See
page
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
23
Cause
Wrong distance or angle.
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
The batteries are weak.
Replace all batteries.
3
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
59
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
59
—
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
■ Resetting the system
Use this feature to reset all the parameters of this unit to
the initial factory settings.
Press 1 STANDBY/ON on the front panel to
set this unit to the standby mode.
2
Press and hold 0 TONE CONTROL and
then press 1 STANDBY/ON to turn on this
unit.
The advanced setup menu appears in the front panel
display.
3
Press B STRAIGHT repeatedly to select
“RESET”.
Select “CANCEL” to cancel the initialization
procedure without making any changes.
4
Press 1 STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
y
To cancel the initialization procedure at any time without making
any changes, press B STRAIGHT repeatedly to select
“CANCEL” and then press 1 STANDBY/ON.
ADDITIONAL
INFORMATION
1
Notes
• This procedure completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
English
67 En
Glossary
Glossary
■ Audio information
Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (front L/R and center), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (Low Frequency Effect), the system
has a total of 5.1-channels (LFE is counted as 0.1
channel). By using 2-channel stereo for the surround
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range from maximum to
minimum volume reproduced by the 5 full-range channels
and the precise sound orientation generated using digital
sound processing provide listeners with unprecedented
excitement and realism. With this unit, any sound
environment from monaural up to a 5.1-channel
configuration can be freely selected for your enjoyment.
Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround sources.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels instead of
only 1 surround channel for conventional Pro Logic
technology. There are three modes available: “Music
mode” for music sources, “Movie mode” for movie
sources and “Game mode” for game sources.
Dolby Surround
Dolby Surround uses a 4-channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range. Dolby Surround is
widely used with nearly all video tapes and laser discs,
and in many TV and cable broadcasts as well. The Dolby
Pro Logic decoder built into this unit employs a digital
signal processing system that automatically stabilizes the
volume on each channel to enhance moving sound effects
and directionality.
68 En
DTS Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 5.1-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. DTS, Inc. has developed a
home theater system so that you can enjoy the depth of
sound and natural spatial representation of DTS digital
surround in your home. This system produces practically
distortion-free 5.1-channel sound (technically, left, right
and center channels, 2 surround channels, plus an LFE 0.1
channel as a subwoofer, for a total of 5.1-channels).
LFE 0.1 channel
This channel reproduces low-frequency bass signals. The
frequency range of this channel is from 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduced by the other 5 channels in Dolby Digital or
DTS 5.1-channel systems.
PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “Pulse Code
Modulation”, the analog signal is encoded as pulses and
then modulated for recording.
Sampling frequency and number of quantized
bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits. The range of rates that can
be played back is determined based on the sampling rate,
while the dynamic range representing the sound level
difference is determined by the number of quantized bits.
In principle, the higher the sampling frequency, the wider
the range of frequencies that can be played back, and the
higher the number of quantized bits, the more finely the
sound level can be reproduced.
Glossary
■ Sound field program information
CINEMA DSP
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers designed for
acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in
the sound heard. Based on a wealth of actually measured
data, Yamaha CINEMA DSP uses Yamaha original DSP
technology to combine Dolby Pro Logic, Dolby Digital
and DTS systems to provide the audiovisual experience of
movie theater in the listening room of your own home.
SILENT CINEMA
Yamaha has developed a natural, realistic sound effect
DSP algorithm for headphones. Parameters for
headphones have been set for each sound field program so
that accurate representations of all the sound field
programs can be enjoyed on headphones.
Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm
that allows you to enjoy DSP surround effects even
without any surround speakers by using virtual surround
speakers. It is even possible to enjoy Virtual CINEMA
DSP using a minimal two-speaker system that does not
include a center speaker.
■ Video information
Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
■ HDMI
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital audio/video
interface. Providing an interface between any source (such
as a set-top box or AV receiver) and an audio/video
monitor (such as a digital television), HDMI supports
standard, enhanced or high-definition video as well as
multi-channel digital audio using a single cable. HDMI
transmits all ATSC HDTV standards and supports
8-channel digital audio, with bandwidth to spare to
accommodate future enhancements and requirements.
When used in combination with HDCP (High-bandwidth
Digital Content Protection), HDMI provides a secure
audio/video interface that meets the security requirements
of content providers and system operators. For further
information on HDMI, visit the HDMI website at
“http://www.hdmi.org/”.
■ MP3
One of the audio compression methods used by MPEG. It
employs the irreversible compression method, which
achieves a high compression rate by thinning out the data
of hardly audible part to the human ears. It is said to be
capable of compressing the data quantity by about 1/11
(128 kbps) while maintaining a similar audio quality to
music CD.
■ WAV
Windows standard audio file format, which defines the
method of recording the digital data obtained by
converting audio signals. It does not specify the
compression (coding) method so a desired compression
method can be used with it. By default, it is compatible
with the PCM method (no compression) and some
compression methods including the ADPCM method.
ADDITIONAL
INFORMATION
Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal. A
monitor with component input jacks is required in order to
output component signals.
S-video signal
With the S-video signal system, the video signal normally
transmitted using a pin cable is separated and transmitted
as the Y signal for the luminance and the C signal for the
chrominance through the S-video cable. Using the S
VIDEO jack eliminates video signal transmission loss and
allows recording and playback of even more beautiful
images.
■ WMA
An audio compression method developed by Microsoft
Corporation. It employs the irreversible compression
method, which achieves a high compression rate by
thinning out the data of hardly audible part to the human
ears. It is said to be capable of compressing the data
quantity by about 1/22 (64 kbps) while maintaining a
similar audio quality to music CD.
English
69 En
Specifications
Specifications
AUDIO SECTION
VIDEO SECTION
• Minimum RMS Output Power for Front, Center, Surround
1 kHz, 0.9% THD, 8 Ω ...................................................... 100 W
• Video Signal Type (Gray back) .............................................. NTSC
• Maximum Power for Front, Center, Surround (JEITA)
1kHz, 10% THD, 8 Ω ........................................................ 135 W
• Dynamic Power
(IHF, 8/6/4/2 Ω) ............................................. 110/130/160/180 W
• Dynamic Headroom
8 Ω ..................................................................................... 0.41 dB
• Maximum Input Signal
CD, etc. Effect On, 1 kHz, 0.5% THD .................... 2.0 V or more
• Frequency Response
CD, etc. to Front L/R ............................ 10 Hz to 100 kHz, –3 dB
• Signal Level
Composite ................................................................. 1 Vp-p/75 Ω
S-video ............................ 1 Vp-p/75 Ω (Y), 0.286 Vp-p/75 Ω (C)
Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)
• Signal to Noise Ratio ................................................. 50 dB or more
• Maximum Input Level ........................................... 1.5 Vp-p or more
• Frequency Response (MONITOR OUT)
Component Signal ................................... 5 Hz to 60 MHz, –3 dB
FM SECTION
• Tuning Range ..................................................... 87.5 to 107.9 MHz
• Total Harmonic Distortion
(1 kHz, 50 W, Front L/R, 8 Ω ) ................................ 0.06% or less
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono ................................................................. 2.8 µV (20.2 dBf)
• Signal to Noise Ratio (IHF-A Network)
CD (200 mV) to Front L/R, Effect Off ................... 98 dB or more
CD (250 mV) to Front L/R, Effect Off ................. 100 dB or more
• Signal to Noise Ratio (IHF)
Mono/Stereo ............................................................. 73 dB/70 dB
• Residual Noise (IHF-A Network)
Front L/R ................................................................ 150 µV or less
• Channel Separation (1 kHz/10 kHz)
CD, etc. (5.1 kΩ terminated) to Front L/R
................................................................... 60 dB/45 dB or more
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................ 0.5%/0.5%
• Antenna Input (unbalanced) ..................................................... 75 Ω
AM SECTION
• Tuning Range ......................................................... 530 to 1710 kHz
• Tone Control (Front L/R)
BASS Boost/Cut .................................................... ±10 dB/100 Hz
TREBLE Boost/Cut .............................................. ±10 dB/20 kHz
GENERAL
• Phones Output .......................................................... 400 mV/470 Ω
• Power Consumption .................................................. 240 W/320 VA
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Standby Power Consumption ...................................... 0.8 W or less
• Output Level/Output Impedance
AUDIO OUT (REC) ............................................ 200 mV/1.2 kΩ
SUBWOOFER OUTPUT ........................................... 4 V/1.2 kΩ
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F.
(FRONT SP, CENTER SP, SUR. L/R SP: SMALL/SML)
......................................................................................12 dB/oct.
L.P.F. (Subwoofer) .........................................................24 dB/oct.
70 En
• Power Supply ........................................................ 120 V AC, 60 Hz
• AC Outlets ............................................ 2 (Total 100 W maximum)
• Dimensions (W x H x D).................................. 435 x 151 x 318 mm
(17-1/8” x 5-15/16” x 12-1/2”)
• Weight .............................................................. 8.1 kg (17 lbs 14 oz)
* Specifications are subject to change without notice.
Index
■
Numerics
■
■
■
A
A)DISPLAY SET, Option menu ......... 54
A)INPUT ASSIGNMENT,
Input menu ....................................... 52
A)SPEAKER SET, Sound menu ......... 48
A.DELAY, Audio settings ................... 51
AC OUTLETS (SWITCHED) ............. 21
AC OUTLETS, Rear panel .................. 10
AM antenna, Connection ..................... 20
AM tuning ............................................ 40
Amplifier function OSD display time,
Display settings ................................ 54
Audio components, Connection ........... 19
Audio delay, Audio settings ................. 51
AUDIO jacks ....................................... 14
Audio jacks .......................................... 14
AUDIO jacks, Rear panel .................... 10
AUDIO SELECT ................................. 33
Audio select, Option menu .................. 55
Audio settings, Sound menu ................ 51
AUTO SETUP ..................................... 24
AUTO SETUP, Error message ............ 64
AUTO: RESULT display,
Auto setup ........................................ 26
Automatic preset tuning,
FM/AM tuning ................................. 41
Automatic tuning, FM/AM tuning ....... 40
■
B
C
D
D)CENTER GEQ, Sound menu ...........51
D)DECODER MODE, Input menu ......53
D)PARAM. INI, Option menu .............55
Decoder mode, Input menu ..................53
Decoder select mode,
Decoder mode ..................................53
Default setting,
Remote control code ........................59
DIGITAL AUDIO COAXIAL jacks ...14
DIGITAL AUDIO OPTICAL jacks .....14
DIGITAL INPUT jacks, Rear panel ....10
■
E
E)LFE LEVEL, Sound menu .............. 51
E)MULTI CH SET, Input menu .......... 54
E-1:NO FRONT SP,
Auto setup error message ................ 65
E-2:NO SURR.SP,
Auto setup error message ................ 65
E-3:NOISY,
Auto setup error message ................ 65
E-4:NO MIC,
Auto setup error message ................ 65
E-5:USER CANCEL,
Auto setup error message ................ 65
E-6:INTERNAL ERROR,
Auto setup error message ................ 65
Effect level, Sound field parameter ..... 39
ENHANCER indicator,
Front panel display .......................... 22
Exchange, Preset station,
FM/AM tuning ................................ 42
■
F
F)D. RANGE, Sound menu ................. 51
Factory presets, Advanced setup ......... 60
FL SCROLL, Display settings ............ 54
FLAG, Input source information ......... 35
FM antenna, Connection ..................... 20
FM tuning ............................................ 40
FORMAT, Input source information ... 35
FRONT B speaker setting,
Speaker settings ............................... 48
FRONT B, Speaker settings ................ 48
Front panel display .............................. 22
Front panel display scroll,
Display settings ............................... 54
FRONT SP, Speaker settings .............. 48
Front speakers, Speaker settings .......... 48
71 En
English
C)AUDIO SELECT, Option menu ...... 55
C)SP DISTANCE, Sound menu .......... 50
C)VOLUME TRIM, Input menu ......... 53
Cable TV, Connection ......................... 16
CD player, Connection ........................ 19
CD recorder, Connection ..................... 19
CENTER SP, Speaker settings ............ 48
Center speaker equalizer,
Sound menu ..................................... 51
Center speaker, Speaker settings ......... 48
DIMENSION,
Sound field parameter ..................... 39
Dimension, Sound field parameter ...... 39
DIMMER, Display settings ................. 54
Dimmer, Display settings .................... 54
DIRECT STEREO ............................... 34
Direct Stereo ........................................ 34
Display settings, Option menu ............ 54
Display, Input source information ....... 35
DIST .................................................... 25
DIST, Auto setup result ....................... 25
DISTANCE ......................................... 25
DISTANCE, Auto setup ...................... 25
DSP LEVEL,
Sound field parameter ..................... 39
DSP level, Sound field parameter ....... 39
DTS decoder prioritize setting,
Decoder mode ................................. 53
DVD player, Connection ..................... 16
DVD recorder, Connection .................. 16
Dynamic range, Sound menu .............. 51
ADDITIONAL
INFORMATION
B)INPUT RENAME, Input menu ....... 53
B)MEMORY GUARD,
Option menu .................................... 55
B)SPEAKER LEVEL,
Sound menu ..................................... 50
Background Video,
Multi channel input setup ................ 54
BGV, Multi channel input setup .......... 54
BITRATE,
Input source information ................. 35
Center width,
Sound field parameter ......................39
CHANNEL,
Input source information ..................35
CINEMA DSP indicator,
Front panel display ...........................22
COAXIAL IN (1),
Input assignment ..............................52
COAXIAL INPUT assignment,
Input assignment ..............................52
COAXIAL INPUT jacks ......................52
COMPONENT VIDEO jacks ..............14
COMPONENT VIDEO jacks,
Connection .......................................18
COMPONENT VIDEO jacks,
Rear panel ........................................10
Connect MIC!,
Auto setup error message .................64
Connecting to the HDMI ......................17
Connection, AM antenna .....................20
Connection, Audio components ...........19
Connection, Cable TV ..........................16
Connection, CD player .........................19
Connection, CD recorder .....................19
Connection,
COMPONENT VIDEO jacks ..........18
Connection, DVD player ......................16
Connection, DVD recorder ..................16
Connection, FM antenna ......................20
Connection, MD recorder .....................19
Connection,
MULTI CH INPUT jacks ................19
Connection, Power cable ......................21
Connection, S VIDEO jacks ................18
Connection, Satellite tuner ...................16
Connection, Speaker ............................12
Connection, Video components ...........16
Connection, Video monitor ..................16
Controlling a TV, Remote control .......57
Controlling other components,
Remote control .................................58
Controlling this unit,
Remote control .................................57
Creating original SCENE templates .....31
CROSSOVER, Speaker settings ..........49
Crossover, Speaker settings .................49
CT WIDTH, Sound field parameter .....39
1 SOUND MENU, Manual setup ........ 46
2 INPUT MENU, Manual setup .......... 46
2ch Stereo, Sound field program ......... 37
3 OPTION MENU ............................... 54
3 OPTION MENU, Manual setup ....... 47
5ch Stereo, Sound field program ......... 37
■
G
G)AUDIO SET, Sound menu .............. 51
Game .................................................... 37
■
H
Hall ....................................................... 37
HDMI ................................................... 15
HDMI jack, HDMI cable plug ............. 15
HDMI jacks, Rear panel ...................... 10
Headphone, Dynamic range ................. 51
HEADPHONE,
Low-frequency effect level .............. 51
Headphone,
Low-frequency effect level .............. 51
Headphones indicator,
Front panel display .......................... 22
Headphones, use .................................. 36
HiFi DSP indicator,
Front panel display .......................... 22
HP, Dynamic range .............................. 51
■
I
Infrared window, Remote control ........ 23
INI.VOL., Audio settings .................... 52
Initial volume, Audio settings .............. 52
Input assignment, Input menu .............. 52
Input channel and speaker indicators,
Front panel display .......................... 22
Input channel indicators,
Front panel display .......................... 22
Input menu, Manual setup ................... 46
Input rename, Input menu .................... 53
Input source indicators,
Front panel display .......................... 22
Input source information display ......... 35
■
J
Jazz ....................................................... 37
■
L
LFE indicator, Front panel display ...... 22
LFE/BASS OUT, Speaker settings ...... 49
LFE/Bass out, Speaker settings ........... 49
Low-frequency effect level, Sound menu
51
LVL ...................................................... 25
LVL, Auto setup result ........................ 25
■
M
Manual preset tuning,
FM/AM tuning ................................. 41
MANUAL SETUP, SET MENU ......... 46
Manual setup, SET MENU .................. 46
Manual tuning, FM/AM tuning ........... 40
MAX VOL., Audio settings ................. 52
Maximum volume, Audio settings ....... 52
MD recorder, Connection .................... 19
Memory guard, Option menu ............... 55
Movie Dramatic ................................... 37
Movie Spacious .................................... 37
MULTI CH INPUT jacks,
Connection ....................................... 19
MULTI CH INPUT jacks,
Rear panel ........................................ 10
72 En
Multi channel input setup,
Input menu .......................................54
Multi-channel source
with headphones ..............................38
Multi-information display,
Front panel display ...........................22
Music Enh. 2ch,
Sound field program ........................37
Music Enh. 5ch,
Sound field program ........................37
MUTE indicator,
Front panel display ...........................22
MUTE TYPE, Audio settings ..............51
Muting ..................................................36
■
N
NIGHT indicator,
Front panel display ...........................22
Night listening mode ............................35
Number of speakers .............................25
Number of speakers,
Auto setup result ..............................25
■
O
OPTICAL IN (2) ..................................52
OPTICAL IN (2), Input assignment ....52
OPTICAL IN (3), Input assignment ....52
OPTICAL INPUT assignment,
Input assignment ..............................52
OPTIMIZER MIC jack, Auto setup .....24
Optimizer microphone .........................24
Optimizer microphone, Auto setup ......24
Optimizing speaker setting ...................24
Option menu, Manual setup .................47
OSD SHIFT, Display settings ..............54
OSD shift, Display settings ..................54
OSD-AMP, Display settings ................54
OSD-SOURCE, Display settings .........54
Other components controlling
by remote control .............................58
Other components controlling,
Remote control .................................58
■
P
PANORAMA,
Sound field parameter ......................39
Panorama, Sound field parameter ........39
Parameter initialization,
Option menu ....................................55
PCM indicator, Front panel display .....22
PHONES jack ......................................36
Play information display,
USB controlling ...............................44
Playing video sources
in the background .............................36
PLII Game ............................................38
PLII Movie ...........................................38
PLII Music ...........................................38
Pop/Rock ..............................................37
Power cable, Connection ......................21
Preset station exchange,
FM/AM tuning .................................42
Preset station selection,
FM/AM tuning .................................42
PRESET, Advanced setup ................... 60
Pro Logic ............................................. 38
Pure hi-fi stereo sound ......................... 34
■
R
Remote control code default setting .... 59
Remote control code setting ................ 59
Remote control codes ........................... iii
Remote control codes setting .............. 59
Remote control, Troubleshooting ........ 67
Rename, SCENE template .................. 31
Resetting the system ............................ 67
■
S
S VIDEO jacks .................................... 14
S VIDEO jacks, Connection ................ 18
SAMPLING,
Input source information ................. 35
Satellite tuner, Connection .................. 16
SCENE 1 ............................................... 8
SCENE 2 ............................................... 8
SCENE 3 ............................................... 8
SCENE 4 ............................................... 9
SCENE template selection .................. 28
Selection, Audio input jack ................. 33
Selection, Preset station,
FM/AM tuning ................................ 42
Selection, SCENE template ................. 28
SET MENU ......................................... 46
Setting remote control code ................. 59
Setting SCENE template input source,
Remote control ................................ 56
Setting the speaker impedance ............ 13
SIGNAL INFO, SET MENU .............. 35
SILENT CINEMA .............................. 38
SILENT CINEMA indicator,
Front panel display .......................... 22
SIZE ..................................................... 25
SIZE, Auto setup ................................. 25
SLEEP indicator,
Front panel display .......................... 22
Sleep timer ........................................... 36
Sound field programs
with headphones .............................. 38
Sound menu, Manual setup ................. 46
Source feature OSD display time,
Display settings ............................... 54
SP ......................................................... 25
SP A B indicators,
Front panel display .......................... 22
SP IMP., Advanced setup .................... 60
SP, Auto setup result ........................... 25
SP, Dynamic range .............................. 51
Speaker distance .................................. 25
Speaker distance, Auto setup ............... 25
Speaker distance, Auto setup result ..... 25
Speaker distance, Sound menu ............ 50
Speaker distances,
Speaker distance .............................. 50
Speaker impedance,
Advanced setup ............................... 60
Speaker level ....................................... 25
Speaker level adjustment ..................... 34
Speaker level, Auto setup result .......... 25
Speaker level, Sound menu .................. 50
Speaker settings, Sound menu ............. 48
Speaker size ......................................... 25
Speaker size, Auto setup ...................... 25
Speaker wiring ..................................... 25
Speaker wiring, Auto setup .................. 25
Speaker wiring/volume level,
Auto setup ........................................ 25
Speaker, Connection ............................ 12
Speaker, Dynamic range ...................... 51
SPEAKER,
Low-frequency effect level .............. 51
Speaker,
Low-frequency effect level .............. 51
SPEAKERS terminals, Rear panel ...... 10
Specifications ....................................... 70
STRAIGHT .......................................... 38
Straight ................................................. 38
SUBWOOFER OUTPUT jack,
Rear panel ........................................ 10
SUBWOOFER PHASE,
Speaker settings ............................... 49
Subwoofer phase, Speaker settings ...... 49
Supplied accessories .............................. 3
SUR. L/R SP, Speaker settings ............ 49
Surround left/right speakers,
Speaker settings ............................... 49
■
VOLUME level indicator,
Front panel display ...........................22
Volume Trim, Input menu ....................53
■
W
W-1:OUT OF PHASE,
Auto setup error message .................65
W-2:DISTANCE ERROR,
Auto setup error message .................65
W-3:LEVEL ERROR,
Auto setup error message .................65
WIRING/LEVEL .................................25
WIRING/LEVEL, Auto setup ..............25
■
Y
Yamaha Parametric Room Acoustic
Optimizer .........................................24
YPAO ...................................................24
YPAO (Yamaha Parametric Room
Acoustic Optimizer) .........................24
YPAO indicator,
Front panel display ...........................22
■
Z
Zone B ..................................................33
T
■
ADDITIONAL
INFORMATION
Test tone, Center speaker equalizer ..... 51
TEST, Center speaker equalizer .......... 51
Tonal quality adjustment ..................... 34
Troubleshooting ................................... 61
Tuner (FM/AM), Troubleshooting ...... 64
Tuner indicators,
Front panel display .......................... 22
Turning off the power .......................... 21
Turning on the power ........................... 21
TV controlling by remote control ........ 57
TV controlling, Remote control ........... 57
TV Sports ............................................. 37
U
UNIT, Speaker distance ....................... 50
Unit, Speaker distance ......................... 50
Unplug HP!,
Auto setup error message ................ 64
USB memory device using,
USB portable audio player using ..... 43
USB playback operation ...................... 43
USB playback styles ............................ 55
USB, Troubleshooting ......................... 66
■
V
English
VIDEO AUX jacks, Front panel .......... 20
Video components, Connection ........... 16
VIDEO jacks ........................................ 14
Video jacks .......................................... 14
VIDEO jacks, Rear panel ..................... 10
Video monitor, Connection .................. 16
Virtual CINEMA DSP ......................... 38
VIRTUAL indicator,
Front panel display .......................... 22
73 En
Front panel
1
2
3
4
5
6
7
8
VOLUME
OPTIMIZER MIC
STANDBY
/ON
EDIT
PRESET/TUNING
FM/AM
l
A/B/C/D/E
PRESET/TUNING
h
MEMORY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
TONE CONTROL
3
4
l
STRAIGHT
INPUT
DIRECT STEREO
VIDEO AUX
h
AUDIO SELECT
EFFECT
SILENT CINEMA
9
i
2
h
0
A
B C
D
E F
VIDEO
L
AUDIO
USB
R
Remote control
Y
A
B
POWER
POWER
TV
AV
MULTI CH IN
STANDBY
POWER
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
M
N
O
P
TV CH
C
V-AUX
USB
AMP
TV INPUT
1
2
TV VOL
TV MUTE
D
E
F
SCENE
BAND LEVEL
TITLE
G
3
4
VOLUME
MENU
R
ENTER
H
S
DISPLAY
RETURN
Q
REC
I
FREQ/TEXT
J
l
PROG h
1
2
MODE – PTY SEEK – START
ENHANCER STRAIGHT
3
8
T
U
ENT
V
4
DIRECT ST.
SUR.DECODE NIGHT
5
6
7
9
0
10
APPENDIX
K
L
EON
W
X
ii
List of remote control codes
TV
ACER
ACME
ACURA
ADA
ADC
ADMIRAL
ADYSON
AGASHI
AGAZI
AGB
AIKO
AIWA
AKAI
AKIBA
AKURA
ALARON
ALBA
ALBIRAL
ALLSTAR
AMPLIVISION
0093
0207
0208
0255
0206
0058, 0205, 0206,
0210, 0211
0200, 0207
0200
0206
0204
0127, 0200, 0207,
0208
0028, 0139, 0229,
0237
0059, 0065, 0127,
0129, 0130, 0200,
0204, 0208, 0209,
0213, 0217, 0218,
0255
0209, 0218
0206, 0209, 0218
0200
0200, 0207, 0208,
0209, 0217, 0218
0212
0213
0207
0204, 0206, 0208,
0209, 0218
AMTRON
0062
ANAM
0208
ANAM NATIONAL
0062
ANGLO
0208
ANITECH
0206, 0208
ANSONIC
0203, 0208
AOC
0060, 0061
APEX
0118, 0122, 0132
ARC EN CIEL 0216
ARCAM
0200
ARCAM DELTA
0207
ARISTONA
0213, 0217
ASA
0205, 0211
ASBERG
0213
ASTRA
0208
ASUKA
0200, 0206, 0207,
0209, 0218
ATLANTIC
0200, 0207, 0213,
0217
ATORI
0208
AUDIOSONIC 0207, 0208, 0209,
0213, 0216, 0217,
0218
AUDIOTON
0207
AUDIOVOX
0062
AUTOVOX
0205, 0206, 0207
AWA
0200
BAIRD
0216
BANG & OLUFSEN
0205
BASIC LINE 0208, 0209, 0213,
0218
BASTIDE
0207
BAUR
0217
BEKO
0228
BELCOR
0060
AMSTRAD
iii
BELL & HOWELL
0058, 0064
BENQ
0051, 0081
BEON
0213, 0217
BESTAR
0213
BINATONE
0207
BLACK STAR 0214
BLAUPUNKT 0255
BLUE SKY
0209, 0218
BONDSTEC 0214
BOOTS
0207
BRADFORD 0062
BRANDT
0216, 0226
BRIONVEGA 0205, 0213, 0217
BRITANNIA 0200, 0207
BROCKWOOD 0060
BROKSONIC 0138
BRUNS
0205
BSR
0215
BTC
0209, 0218
BUSH
0177, 0208, 0209,
0210, 0213, 0215,
0216, 0217, 0218,
0230, 0237
CANDLE
0060, 0061
CAPSONIC
0206
CASCADE
0208
CATHAY
0213, 0217
CCE
0127
CELEBRITY 0059
CENTURION 0213, 0217
CENTURY
0205
CGE
0214, 0215
CIMLINE
0208, 0218
CITIZEN
0060, 0061, 0062,
0064
CITY
0208
CLARIVOX
0212, 0217
CLATRONIC 0206, 0207, 0208,
0209, 0213, 0214,
0218
CMS
0200
COLORTYME 0060, 0061
CONCERTO 0060, 0061
CONCORDE 0208
CONDOR
0200, 0207, 0213
CONTEC
0200, 0207, 0208
CONTEC/CONY
0062
CONTINENTAL EDISON
0216
COSMEL
0208
CRAIG
0062
CROSLEY
0205, 0214, 0215
CROWN
0062, 0063, 0128,
0208, 0213, 0217
CS ELECTRONICS
0200, 0207, 0209,
0214, 0218
CTC
0214
CURTIS MATHES
0057, 0060, 0061,
0064, 0065
CXC
0062
CYBERTRON 0209, 0218
DAEWOO
0060, 0061, 0120,
0127, 0155, 0193,
0200, 0207, 0208,
0213, 0218, 0238
DAINICHI
0200, 0209, 0218
DANSAI
0200, 0206, 0213,
0217
DANTAX
DAYTRON
DE GRAAF
DECCA
0217
0060, 0061, 0208
0210
0204, 0207, 0213,
0217
DESMET
0213, 0217
DIAMOND
0200
DIMENSIA
0057
DIXI
0208, 0213, 0217
DTS
0208
DUAL
0207, 0215, 0216
DUAL-TEC
0207, 0208, 0215
DUMONT
0060, 0127, 0205,
0207
DURABRAND 0126
DUX
0217
DYNATRON 0213, 0217
ELBE
0203, 0204, 0212,
0218
ELBE-SHARP 0204
ELCIT
0204, 0205
ELECTRO TECH
0208
ELECTROBAND
0059
ELECTROHOME
0059, 0060, 0061
ELIN
0200, 0207, 0213,
0217
ELITE
0209, 0213, 0218
ELMAN
0215
ELTA
0200, 0208
EMERSON
0060, 0061, 0062,
0064, 0128, 0205
ENVISION
0060, 0061
ERRES
0213, 0217
ESA
0080
ETRON
0208
EURO-FEEL 0206
EUROLINE
0217
EUROMAN
0200
EUROMANN 0206, 0207, 0213
EUROPHON 0200, 0204, 0207,
0213, 0215
FENNER
0208
FERGUSON 0212, 0217, 0226
FIDELITY
0200, 0207, 0210
FINLANDIA 0210
FINLUX
0204, 0205, 0207,
0213, 0215, 0217
FIRSTLINE
0200, 0207, 0208,
0213, 0214
FISHER
0064, 0127, 0128,
0205, 0207, 0215
FLINT
0213, 0218
FORMENTI
0200, 0205, 0207,
0215, 0217
FORMENTI-PHOENIX
0200
FORTRESS
0205
FRONTECH
0206, 0208, 0210,
0211, 0214
FUJITSU
0023, 0024, 0025,
0088, 0127
FUNAI
0033, 0034, 0035,
0036, 0037, 0062,
0206
FUTURETECH 0062
GATEWAY
0094
GBC
0208, 0215, 0218
GE
0057, 0060, 0061,
0122, 0147
GEC
0204, 0207, 0211,
0213, 0217
GELOSO
0208, 0210, 0215
GENERAL TECHNIC
0208
GENEXXA
0209, 0211, 0213,
0218
GIBRALTER 0060
GOLDHAND 0200
GOLDSTAR 0060, 0061, 0127,
0128, 0200, 0201,
0207, 0208, 0210,
0213, 0214, 0215,
0217
GOODMANS 0171, 0201, 0204,
0206, 0208, 0213,
0217, 0240
GPM
0209, 0218
GRAETZ
0211
GRANADA
0204, 0207, 0210,
0213, 0217
GRANDIN
0208, 0209, 0217
GRUNDIG
0128, 0130, 0222,
0236, 0255
GRUNPY
0062
HALIFAX
0200, 0206, 0207
HALLMARK 0060, 0061
HAMPTON
0200, 0207
HANSEATIC 0203, 0207, 0208,
0213, 0215, 0217
HANTAREX 0204, 0208
HARVARD
0062
HCM
0206, 0207, 0208,
0218
HIFIVOX
0216
HIGASHI
0200
HINARI
0208, 0209, 0213,
0217, 0218
HISAWA
0209, 0218
HITACHI
0006, 0014, 0015,
0016, 0042, 0060,
0061, 0095, 0105,
0127, 0156, 0179,
0180, 0204, 0207,
0210, 0211, 0215,
0216, 0251
HORNYPHON 0213
HOSHAI
0209, 0218
HUANYU
0200, 0207
HYGASHI
0200, 0207
HYPER
0200, 0207, 0208,
0214, 0215
HYPSON
0206, 0207, 0213,
0217
ICE
0127, 0200, 0206,
0207, 0208, 0209,
0213, 0218
ICES
0200, 0218
IMA
0062
IMPERIAL
0211, 0213, 0214,
0215
INDIANA
0213, 0217
INFINITY
0063
INGELEN
0211
INGERSOL
0208
INNO HIT
0201, 0204, 0207,
0208, 0209, 0213,
0217, 0218
INNOVATION 0206, 0208
INTERBUY
0208, 0214
INTERFUNK 0205, 0211, 0213,
0214, 0216, 0217
MANESTH
0206, 0207, 0213,
0217
MARANTZ
0060, 0061, 0063,
0090, 0213, 0217
MARELLI
0205
MARK
0200, 0213, 0217
MATSUI
0204, 0207, 0208,
0210, 0213, 0217
MEDIATOR
0213, 0217
MEDION
0206, 0208
MEGATRON 0061
MELECTRONIC
0200, 0207, 0208,
0211, 0213, 0216,
0217
MEMOREX
0058, 0061, 0064,
0208
MEMPHIS
0208
METZ
0205
MGA
0060, 0061
MICROMAXX 0206, 0208
MICROSTAR 0206, 0208
MINERVA
0204
MINOKA
0213
MITSUBISHI 0006, 0015, 0016,
0048, 0060, 0061,
0104, 0112, 0113,
0125, 0205, 0213
MIVAR
0200, 0201, 0202,
0203, 0204, 0207
MONTGOMERY WARD
0058
MTC
0060, 0061, 0128,
0200
MULTI SYSTEM
0217
MULTITECH 0062, 0127, 0128,
0200, 0207, 0208,
0210, 0214, 0215,
0217
MURPHY
0200, 0207
NAD
0061
NAONIS
0210
NEC
0026, 0053, 0060,
0061, 0096, 0127
NECKERMANN
0205, 0207, 0210,
0213, 0217, 0255
NEI
0213, 0217
NESCO
0214
NET-TV
0082, 0101
NEW TECH
0208, 0213
NEW WORLD 0209, 0218
NICAMAGIC 0200, 0207
NIKKAI
0200, 0206, 0207,
0209, 0213, 0217,
0218
NIKKO
0061
NOBLIKO
0200, 0207
NOGAMATIC 0216
NOKIA
0129, 0211
NORDMENDE
0205, 0211, 0213,
0216
NORDVISION 0217
OCEANIC
0211
OLEVIA
0052, 0084
ONCEAS
0207
ONWA
0062, 0218
ORBIT
0213
ORION
0126, 0204, 0208,
0213, 0217, 0235
ORLINE
0218
ORSOWE
0204
OSAKI
0127, 0206, 0207,
0209, 0218
OSIO
0201
OSO
0209, 0218
OSUME
0218
OTTO VERSAND
0204, 0207, 0213,
0215, 0216, 0217,
0255
PAEL
0200, 0207
PALLADIUM 0207
PANAMA
0200, 0206, 0207,
0208
PANASONIC 0006, 0007, 0063,
0073, 0074, 0097,
0110, 0114, 0137,
0141, 0151, 0162,
0165, 0186, 0204,
0211, 0244, 0245,
0246, 0254
PATHE CINEMA
0200, 0203, 0207,
0212, 0215
PATHE MARCONI
0212, 0216
PAUSA
0208
PERDIO
0200
PHILCO
0060, 0061, 0063,
0128, 0205, 0214,
0215
PHILHARMONIC
0207
PHILIPS
0040, 0060, 0063,
0072, 0115, 0116,
0124, 0130, 0150,
0175, 0184, 0187,
0205, 0207, 0213,
0215, 0217, 0220,
0221, 0232, 0233,
0252, 0253
PHILIPS MAGNAVOX
0124
PHOENIX
0200, 0205, 0213,
0217
PHONOLA
0200, 0205, 0213,
0217
PILOT
0060
PIONEER
0012, 0013, 0060,
0061, 0098, 0109,
0117, 0128, 0181,
0182, 0194, 0195,
0211, 0213, 0216,
0217, 0250
PLANTRON 0206, 0213
POLAROID
0075
POPPY
0208
PORTLAND 0060, 0061
PRANDONI-PRINCE
0204, 0210
PRECISION
0207
PRIMA
0208, 0211
PROFEX
0208
PROFI-TRONIC
0213
PROLINE
0213
PROSCAN
0057
PROSONIC
0200, 0207, 0217
PROTECH
0206, 0207, 0208,
0213, 0214, 0215,
0217
PROTON
0060, 0061
PROVIEW
0050
PROVISION
0217
PULSAR
0060
PYE
0213, 0217
PYMI
0208
QUASAR
0152, 0214
QUELLE
0201, 0206, 0207,
0213, 0214, 0215,
0217
RADIALVA
0218
RADIO SHACK
0064
RADIO SHACK/REALISTIC
0057, 0060, 0061,
0062, 0064
RADIOLA
0213, 0217
RADIOMARELLI
0204, 0205, 0214
RADIOTONE 0213
RCA
0057, 0060, 0061,
0091, 0133, 0135,
0147, 0149
REALISTIC
0064
REVOX
0213, 0217
REX
0206, 0210, 0211
RFT
0203, 0205
RHAPSODY 0200
R-LINE
0213, 0217
ROADSTAR
0206, 0208, 0209,
0218, 0237
ROBOTRON 0205
ROWA
0200
RTF
0205
SABA
0204, 0205, 0211,
0216
SACCS
0212
SAISHO
0204, 0206, 0207,
0208
SALORA
0201, 0204, 0210,
0211, 0215
SAMBERS
0204
SAMPO
0060, 0061, 0083,
0101
SAMSUNG
0029, 0030, 0031,
0032, 0044, 0045,
0046, 0047, 0060,
0061, 0065, 0068,
0069, 0071, 0079,
0087, 0127, 0128,
0130, 0144, 0160,
0161, 0170, 0176,
0183, 0185, 0200,
0201, 0206, 0207,
0208, 0213, 0217,
0239, 0241, 0242,
0243
SANDRA
0200, 0207
SANSUI
0123, 0126, 0213
SANYO
0020, 0021, 0022,
0049, 0060, 0064,
0127, 0128, 0200,
0203, 0207, 0215
SBR
0217
SCHAUB LORENTZ
0211
SCHNEIDER 0207, 0209, 0213,
0215, 0216, 0217,
0218
SCOTCH
0061
SCOTT
0060, 0061, 0062
SEARS
0057, 0060, 0061,
0064
SEG
0200, 0206, 0207,
0214, 0215, 0217
SEI
0204
SEI-SINUDYNE
0204, 0205, 0211
SELECO
0210, 0211, 0215
SENCORA
0208
SENTRA
0218
SERINO
0200
iv
APPENDIX
INTERNATIONAL
0200
INTERVISION 0206, 0207, 0218
IRRADIO
0201, 0208, 0209,
0213, 0217, 0218
ISUKAI
0209, 0218
ITC
0207, 0215
ITS
0200, 0209, 0213,
0218
ITT
0129, 0208, 0211
ITV
0208, 0217
JBL
0063
JC PENNEY 0057, 0060, 0061
JCB
0059
JENSEN
0060, 0061
JVC
0017, 0018, 0019,
0108, 0136, 0153,
0178, 0190, 0213,
0218
KAISUI
0200, 0207, 0208,
0209, 0218
KAMOSONIC 0207
KAMP
0200, 0207
KAPSCH
0211
KARCHER
0207, 0208, 0212,
0217
KAWASHO
0059, 0060, 0061,
0200
KENDO
0128, 0210
KENNEDY
0215
KENWOOD
0060, 0061
KINGSLEY
0200, 0207
KLOSS NOVABEAM
0062
KNEISSEL
0203
KOLSTER
0213
KONKA
0209, 0218
KORPEL
0213, 0217
KORTING
0205
KOYODA
0208
KTV
0062, 0127, 0207
KYOTO
0200, 0212
LENCO
0208
LENOIR
0207, 0208
LESA
0214
LEYCO
0206, 0213, 0217
LG
0016, 0038, 0039,
0127, 0128, 0157,
0158, 0163, 0164,
0166, 0188, 0189,
0200, 0201, 0207,
0208, 0210, 0213,
0214, 0215, 0217
LIESENK
0217
LIFE
0206, 0208
LIFETEC
0206, 0208, 0218
LOEWE
0063, 0128, 0203,
0204, 0223, 0227
LOEWE OPTA 0205, 0213, 0217
LOGIK
0058
LUMA
0210, 0217
LUMATRON 0210, 0213, 0217
LUX MAY
0213
LUXMAN
0060, 0061
LUXOR
0201, 0207, 0210
LXI
0057, 0061, 0063,
0064
MAG
0050
MAGNADYNE
0204, 0205, 0214,
0215, 0217
MAGNAFON 0200, 0204, 0207
MAGNAVOX 0060, 0061, 0063,
0102, 0103, 0150
MAGNUM
0206, 0208
MAJESTIC
0058
MANDOR
0206
SHARP
0009, 0010, 0011,
0060, 0061, 0066,
0070, 0087, 0111,
0143, 0145, 0167,
0168, 0169, 0198,
0204, 0224, 0247,
0248, 0249
SHOGUN
0060
SIAREM
0204, 0205, 0215
SICATEL
0212
SIEMENS
0255
SIERRA
0213
SIGNATURE 0058
SILVA
0200
SINGER
0205, 0214, 0215
SINUDYNE
0204, 0205, 0215,
0217
SKANTIC
0211
SOLAVOX
0211
SONOKO
0206, 0207, 0208,
0213, 0217
SONOLOR
0211
SONTEC
0213, 0217
SONY
0041, 0059, 0067,
0085, 0086, 0174,
0196, 0199, 0208,
0219, 0234
SOUND & VISION
0209, 0218
SOUNDESIGN 0060, 0061, 0062
SOUNDWAVE 0213, 0217
SSS
0060, 0062
STANDARD 0207, 0208, 0209,
0213, 0218
STARLIGHT 0217
STARLITE
0062
STENWAY
0218
STERN
0210, 0211
SUNKAI
0208, 0218
SUNWOOD
0208, 0213
SUPERLA
0200, 0204, 0207
SUPERTECH 0200
SUPRA
0208
SUPREME
0059
SUSUMU
0209
SUTRON
0208
SYDNEY
0200, 0207
SYLVANIA
0060, 0061, 0063,
0080, 0134, 0142,
0148
SYMPHONIC 0062, 0080
SYSLINE
0217
SYTONG
0200
TANDY
0127, 0207, 0209,
0211, 0218
TASHIKO
0200, 0207, 0210
TATUNG
0127, 0204, 0207,
0213, 0217, 0237
TCM
0206, 0208
TEAC
0127
TEC
0207, 0208, 0214,
0215
TECHWOOD 0060, 0061
TEKNIKA
0058, 0060, 0061,
0062
TELEAVIA
0216
TELECOR
0218
TELEFUNKEN
0065, 0213, 0216
TELEGAZI
0218
TELETECH
0208, 0214, 0217
TELETON
0207
TELEVIDEON 0200
TENSAI
0208, 0209, 0213,
0218
TESMET
0213
TEVION
0206, 0208
v
TEXET
THOMSON
0200, 0207
0191, 0192, 0207,
0213, 0216, 0226
THORN
0212, 0217
TMK
0060, 0061
TOKAI
0213
TOKYO
0200, 0207
TOSHIBA
0027, 0043, 0053,
0054, 0064, 0078,
0089, 0090, 0106,
0107, 0127, 0131,
0140, 0146, 0159,
0197, 0225, 0231,
0237
TOWADA
0211, 0215
TRANSTEC
0200
TRIDENT
0204
TRISTAR
0218
TRIUMPH
0204
UHER
0211, 0213
ULTRAVOX
0200, 0205, 0207,
0214, 0215
UNITED
0217
UNIVERSUM 0127, 0128, 0129,
0201, 0206, 0213,
0214, 0215, 0217
UNIVOX
0212
VESTEL
0210, 0211, 0213,
0214, 0215, 0217
VEXA
0208, 0217
VICTOR
0213
VIDEOLOGIC 0200
VIDEOLOGIQUE
0200, 0207, 0209,
0218
VIDEOSAT
0214
VIDEOSYSTEM
0213
VIDEOTECHNIC
0200
VIDTECH
0060, 0061
VIEWSONIC 0076, 0077, 0092,
0099, 0172, 0173
VISIOLA
0200, 0207
VISION
0213
VORTEC
0213, 0217
VOXSON
0205, 0210, 0211,
0213
WALTHAM
0207, 0212
WARDS
0057, 0058, 0060,
0061, 0063
WATSON
0213, 0217, 0218
WATT RADIO 0200, 0207, 0212,
0215
WEGA
0205
WELTBLICK 0213, 0217
WESTON
0215
WHITE WESTINGHOUSE
0008, 0200, 0207,
0217
WINCOM
0055, 0056
YAMAHA
0000, 0001, 0002,
0003, 0005, 0060,
0061
YAMISHI
0218
YOKO
0200, 0206, 0207,
0208, 0209, 0213,
0217, 0218
YORX
0209, 0218
ZANUSSI
0210
ZENITH
0058, 0060, 0100,
0105, 0119, 0121,
0154
TV/DVD COMBO
AIWA
0139, 2055
APEX
0132, 2049
BROKSONIC 0138, 2060
BUSH
0230, 2112
JVC
0136, 2053
PANASONIC 0137, 2054, 0254,
2110
RCA
0133, 0135, 2050,
2051
SYLVANIA
0134, 2052
THOMSON
0226, 2109
TOSHIBA
0131, 2048, 0231,
2111
TV/DVD/VCR COMBO
PANASONIC
SAMSUNG
SHARP
SYLVANIA
TOSHIBA
0141, 1040, 2057
0241, 1070, 2113
0143, 1028, 2059
0142, 1041, 2058
0140, 1029, 2056
TV/VCR COMBO
AIWA
BUSH
DAEWOO
0237, 1066
0237, 1066
0155, 0238, 1038,
1067
GE
0147, 1030
GOODMANS 0240, 1069
GRUNDIG
0236, 1062
HITACHI
0156, 1039
JVC
0153, 1036
MAGNAVOX 0150, 1033
ORION
0235, 1065
PANASONIC 0151, 1034
PHILIPS
0150, 0232, 0233,
1033, 1062, 1063
QUASAR
0152, 1035
RCA
0149, 1032
ROADSTAR
0237, 1066
SAMSUNG
0144, 0239, 1027,
1068
SHARP
0145, 1028
SONY
0234, 1064
SYLVANIA
0148, 1031
TATUNG
0237, 1066
TOSHIBA
0146, 0237, 1029,
1066
ZENITH
0154, 1037
DVD/VCR COMBO
JVC
LG
PANASONIC
PHILIPS
RCA
SAMSUNG
SHARP
SONY
TOSHIBA
ZENITH
1017, 1017, 2045,
2045
1071, 2087
1020, 1072, 2040,
2105
1025, 2046
1022, 2042
1021, 1021, 2041,
2104
1023, 1073, 2043,
2106
1019, 1074, 2039,
2107
1024, 1075, 2044,
2108
1026, 2047
VCR
ADMIRAL
1008, 1013
ADVENTURA
1005
AIWA
1005, 1042, 1043,
1044, 1066
AKAI
1007, 1043
AKIBA
1050
AKURA
1043, 1050
ALBA
1044, 1050
AMERICAN HIGH
1004
AMSTRAD
1042
ANITECH
1050
ASA
1045, 1046
ASHA
1002, 1014
ASUKA
1042, 1045, 1046,
1050
AUDIO DYNAMICS
1000
AUDIOVOX
1003
BAIRD
1042, 1043, 1047
BASIC LINE 1044, 1050
BAUR
1046
BEAUMARK 1002, 1014
BELL & HOWELL
1001
BLAUPUNKT 1046, 1048
BROKSONIC 1012, 1013
BUSH
1044, 1050, 1066
CALIX
1003
CANDLE
1002, 1003
CANON
1004
CCE
1006
CGE
1042, 1043
CIMLINE
1044, 1050
CITIZEN
1002, 1003
COLORTYME 1000
COLT
1006
CRAIG
1002, 1003, 1006,
1014
CROWN
1050
CURTIS MATHES
1000, 1002, 1004,
1009
CYBERNEX 1002, 1014
DAEWOO
1005, 1038, 1061,
1067
DANSAI
1050
DANTAX
1044
DBX
1000
DE GRAAF
1046, 1049
DECCA
1042, 1043, 1046
DENON
1010
DIMENSIA
1009
DUAL
1043, 1046
DUMONT
1042, 1046, 1047,
1049
DYNATECH 1005
ELECTROHOME
1003
ELECTROPHONIC
1003
ELTA
1050
EMERSON
1003, 1004, 1005,
1012, 1013
ETZUKO
1050
FERGUSON 1043
FIDELITY
1042
FINLANDIA 1046, 1047, 1049
FINLUX
1042, 1043, 1046,
1047, 1049
FIRST LINE 1044, 1045, 1049,
1050
FISHER
1001, 1047
FLINT
1044
FORMENTI/PHOENIX
1046
FUJI
1004
FUJITSU
1042
FUNAI
1005, 1042
GALAXY
1042
GARRARD
1005
GBC
1050
GE
MARANTZ
1000, 1001, 1004,
1046, 1051
MARTA
1003
MATSUI
1044, 1045
MATSUSHITA 1004
MEDIATOR
1046
MEDION
1044, 1048
MEI
1004
MEMOREX
1001, 1002, 1003,
1004, 1005, 1008,
1013, 1014, 1042,
1045, 1047
MEMPHIS
1050
METZ
1048
MGA
1014
MGN TECHNOLOGY
1002, 1014
MICROMAXX 1044, 1048
MICROSTAR 1044, 1048
MIGROS
1042
MINOLTA
1010
MITSUBISHI 1011, 1042, 1046
MONTGOMERY WARD
1008
MOTOROLA 1004, 1008
MTC
1002, 1014
MULTITECH 1002, 1005, 1006,
1042, 1046, 1050
MURPHY
1042
NATIONAL
1048
NEC
1000, 1001, 1007,
1011, 1043, 1051
NECKERMANN
1043, 1046
NEI
1046
NESCO
1050
NIKKO
1003
NOBLEX
1002, 1014
NOKIA
1043, 1047
NORDMENDE
1043
OCEANIC
1042, 1043
OKANO
1044
OLYMPUS
1004
OPTIMUS
1003, 1008
ORION
1012, 1013, 1044,
1065
ORSON
1042
OSAKI
1042, 1045, 1050
OTTO VERSAND
1046
PALLADIUM 1043, 1045, 1050
PANASONIC 1004, 1020, 1034,
1040, 1048, 1054,
1072
PATHE MARCONI
1043
PENNEY
1010, 1014
PENTAX
1010, 1049
PERDIO
1042
PHILCO
1004, 1051
PHILIPS
1004, 1025, 1033,
1046, 1056, 1057,
1059, 1062, 1063
PHILIPS MAGNAVOX
1018
PHONOLA
1046
PILOT
1003
PIONEER
1011, 1046
PRINZ
1042
PROFEX
1050
PROFITRONIC
1014
PROLINE
1042
PROSCAN
1009
PROSONIC
1044
PROTEC
1006
PYE
1046, 1056
QUARTER
1001
QUARTZ
1001, 1047
QUASAR
1004, 1035
QUELLE
1042, 1046, 1047
RADIO SHACK
1003
RADIO SHACK/REALISTIC
1001, 1002, 1003,
1004, 1005, 1008
RADIOLA
1046
RADIX
1003
RANDEX
1003
RCA
1002, 1004, 1009,
1010, 1014, 1015,
1022, 1032
REALISTIC
1001, 1002, 1003,
1004, 1005, 1008
REX
1043
RFT
1046
ROADSTAR
1045, 1050, 1066
SABA
1043
SAISHO
1044, 1050
SALORA
1047
SAMSUNG
1002, 1014, 1021,
1027, 1052, 1068,
1070
SANKY
1008
SANSUI
1007, 1011, 1013,
1043
SANYO
1001, 1002, 1014,
1047
SBR
1046
SCHAUB LORENZ
1042, 1043, 1047
SCHNEIDER 1042, 1044, 1045,
1046, 1050
SCOTT
1012
SEARS
1001, 1003, 1004,
1010
SEG
1050
SEI-SINUDYNE
1046
SELECO
1043
SENTRON
1050
SHARP
1008, 1023, 1028,
1053, 1073
SHINTOM
1006, 1047, 1050
SHIVAKI
1045
SHOGUN
1002, 1014
SIEMENS
1045, 1047
SIGNATURE 2000
1008
SILVA
1045
SINGER
1004, 1006
SINUDYNE
1046
SONTEC
1045
SONY
1016, 1019, 1055,
1060, 1064, 1074
STS
1004, 1010
SUNKAI
1044
SUNSTAR
1042
SUNTRONIC 1042
SUNWOOD
1050
SYLVANIA
1004, 1005, 1031,
1041
SYMPHONIC 1005
TAISHO
1044
TANDY
1001
TASHIKO
1003, 1042
TATUNG
1007, 1042, 1043,
1046, 1066
TCM
1044, 1048
TEAC
1005, 1007
TECHNICS
1004, 1048
TEKNIKA
1003, 1004, 1005
TELEAVIA
1043
TELEFUNKEN
1043
1050
1042, 1045, 1050
1044, 1048
1043, 1058
1043, 1047
1002, 1014
1045, 1050
1050
1013, 1024, 1029,
1043, 1046, 1066,
1075
TOTEVISION 1002, 1003, 1014
TOWADA
1050
TOWIKA
1050
UHER
1045
UNITECH
1002, 1014
UNIVERSUM 1042, 1045, 1046
VECTOR RESEARCH
1000
VIDEO CONCEPTS
1000
VIDEON
1044, 1048
VIDEOSONIC 1002, 1014
WARDS
1002, 1003, 1004,
1005, 1006, 1008,
1010, 1014
WELTBLICK 1045
WHITE WESTINGHOUSE
1013
XR-1000
1004, 1005, 1006
YAMAHA
1000, 1001, 1007
YAMISHI
1050
YOKAN
1050
YOKO
1045, 1050
ZENITH
1013, 1026, 1037
TENOSAL
TENSAI
TEVION
THOMSON
THORN
TMK
TOKAI
TONSAI
TOSHIBA
DVD
ACOUSTIC SOLUTIONS
2078
AIWA
2055, 2100
AKAI
2096
AKURA
2076
ALBA
2078, 2086
APEX
2027, 2049
AWA
2078
AXION
2078
BRAINWAVE 2096
BRANDT
2073, 2085
BROKSONIC 2060
BUSH
2075, 2078, 2112
CENTREX
2077
CLASSIC
2078
CLATRONIC 2075
COBY
2078
C-TECH
2074
CYBERHOME
2025, 2079, 2091
DAEWOO
2092, 2098
DANSAI
2096
DAYTEK
2080, 2089
DEC
2075
DENON
2030, 2102, 2103
DENVER
2075, 2076
DIAMOND
2074
DK DIGITAL 2094
DUAL
2078
D-VISION
2096
DVX
2074
ELTA
2096
EUROLINE
2096
FUNAI
2052, 2058
GLOBAL SOLUTIONS
2074
vi
APPENDIX
1002, 1004, 1009,
1014, 1030
GEC
1046
GELOSO
1050
GENERAL TECHNIC
1044, 1048
GO VIDEO
1014
GOLDHAND 1050
GOLDSTAR
1000, 1003, 1042,
1045
GOODMANS 1042, 1045, 1050,
1069
GRADIENTE 1005
GRAETZ
1043, 1047
GRANADA
1046, 1047, 1049
GRANDIN
1042, 1045, 1050
GRUNDIG
1046, 1050, 1062
HANSEATIC 1045, 1046
HARLEY DAVIDSON
1005
HARMAN/KARDON
1000
HARWOOD
1006
HCM
1050
HEADQUARTER
1001
HINARI
1044, 1050
HISAWA
1044
HITACHI
1007, 1010, 1039,
1042, 1043, 1046,
1049
HUGHES NETWORK SYSTEMS
1010
HYPSON
1044, 1050
IMPERIAL
1042
INNO HIT
1046, 1050
INNOVATION 1044, 1048
INSTANT REPLAY
1004
INTERBUY
1045
INTERFUNK 1046, 1047
INTERVISION 1042
IRRADIO
1045, 1050
ITT
1043, 1047
ITV
1045
JC PENNEY 1000, 1001, 1002,
1003, 1004, 1006
JCL
1004
JENSEN
1007
JVC
1000, 1001, 1007,
1011, 1017, 1036,
1043
KAISUI
1050
KARCHER
1046
KENDO
1044
KENWOOD
1000, 1001, 1007,
1011, 1043
KLH
1006
KODAK
1003, 1004
KORPEL
1050
LEYCO
1050
LG
1003, 1042, 1045,
1071
LIFETEC
1044, 1048
LLOYD'S
1005
LOEWE
1048
LOEWE OPTA 1045, 1046
LOGIK
1006, 1050
LUXOR
1047
LXI
1003
M ELECTRONIC
1042
MAGNASONIC
1047
MAGNAVOX 1004, 1018, 1033
MAGNIN
1003, 1014
MANESTH
1050
GLOBAL SPHERE
2074
GOODMANS 2075, 2077, 2078
GRUNDIG
2077, 2098
H&B
2075
HAAZ
2074
HE
2078
HITACHI
2032, 2072
HOME ELECTRONICS
2078
INNOVATION 2072
IRRADIO
2134
JDB
2078
JVC
2033, 2045, 2053,
2073, 2099
KENWOOD
2030, 2097
KINGAVON
2075
KODA
2075
LAWSON
2074
LENCO
2075
LG
2084, 2087
LIFETEC
2072
LIMIT
2074
LOGICLAB
2074
LUXOR
2077
MAGNAVOX 2037, 2073, 2075
MAGNUM
2072
MBO
2078
MEDION
2072
MICROMAXX
2072
MICROMEDIA
2073
MICROSTAR 2072
MITSUBISHI 2035
MIZUDA
2075
MUSTEK
2078
NAIKO
2077
ONKYO
2073, 2135
ORAVA
2075
P&B
2075
PACIFIC
2074
PANASONIC 2030, 2040, 2054,
2057, 2105, 2110
PHILIPS
2019, 2026, 2046,
2073, 2081, 2090
PIONEER
2036, 2082
PROLINE
2077
PROVISION 2075
RCA
2031, 2042, 2050,
2051
RED STAR
2076
REOC
2074
ROADSTAR
2075, 2078, 2086
ROWA
2077
SABA
2085
SABAKI
2074
SAMSUNG
2032, 2041, 2104,
2113
SANSUI
2074
SANYO
2095
SCANMAGIC 2078
SCIENTIFIC LABS
2074
SCOTT
2088
SEG
2074, 2086
SHARP
2034, 2043, 2059,
2093, 2106
SILVA
2076
SINGER
2074
SKYMASTER 2074, 2078
SKYWORTH 2076
SM ELECTRONIC
2074, 2078
SONY
2028, 2029, 2039,
2083, 2107
SOUNDMASTER
2074
SOUNDMAX 2074
STANDARD 2074
STAR CLUSTER
2074
STARMEDIA 2075
SUPERVISION
2074, 2078
SYLVANIA
2052, 2058
SYNN
2074
TCM
2072
TEAC
2074
TEC
2076
TECHNICS
2030
TECHNIKA
2096
TECHNOSONIC
2096
TEVION
2072, 2074
THOMSON
2085, 2109
TOKAI
2076
TOSHIBA
2026, 2044, 2048,
2056, 2073, 2108,
2111
UNITED
2078
VOXSON
2078
WHARFEDALE
2074
XLOGIC
2074
YAKUMO
2077
YAMADA
2077
YAMAHA
2000, 2001, 2003,
2030, 2101
YUKAI
2078
ZENITH
2038, 2047, 2073
DVD-DVR
PANASONIC
PIONEER
SAMSUNG
2067
2114
2115
TOSHIBA
PANASONIC
2068
DVD/LD COMBO
PIONEER
2036
DVD RECORDER
APEX
JVC
LG
PANASONIC
PHILIPS
PIONEER
RCA
SONY
TOSHIBA
YAMAHA
YUKAI
2024
2070
2071
2020, 2065, 2066,
2067
2019, 2061, 2062,
2063
2021
2018
2022, 2064
2068
2023
2069
DVR
ABS
2132
ALIENWARE 2132
CYBERPOWER
2132
DELL
2132
DIRECTV
2123, 2128, 2129,
2133
DISH NETWORK
2126, 2127
DISHPRO
2126
ECHOSTAR
2126, 2127
EXPRESSVU 2126
GATEWAY
2132
GOI
2126
HEWLETT PACKARD
2132
HITACHI
2008
HOWARD COMPUTERS
2132
HTS
2126
HUGHES
2123, 2128
HUMAX
2123
HUSH
2132
IBUYPOWER 2132
JVC
2126, 2127
LINKSYS
2132
MEDIA CENTER PC
2132
MICROSOFT 2132
MIND
2132
NIVEUS MEDIA
2132
NORTHGATE 2132
© 2007
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
2015, 2016, 2017,
2120
PHILIPS
2117, 2121, 2123,
2128
PIONEER
2012, 2013, 2014
PROSCAN
2129
RCA
2116, 2124, 2129,
2133
REPLAYTV
2118, 2119, 2120
SHARP
2009, 2010
SONIC BLUE 2119, 2120
SONY
2005, 2006, 2007,
2122, 2130, 2131,
2132
STACK 9
2132
SYSTEMAX 2132
TAGAR SYSTEMS
2132
TIVO
2116, 2121, 2122,
2123, 2130, 2131
TOSHIBA
2004, 2125, 2132
TOUCH
2132
ULTIMATETV 2133
VIEWSONIC 2132
VOODOO
2132
YAMAHA
2011
ZT GROUP
2132
LD PLAYER
YAMAHA
2002
CD PLAYER
YAMAHA
5000, 5013
CD RECORDER
YAMAHA
5001
MD
YAMAHA
5002, 5003, 5004
TAPE DECK
YAMAHA
5005, 5006
TUNER
YAMAHA
5007, 5008, 5009,
5010, 5012, 5014
All rights reserved.
Printed in China
WK65630
1
SILENT CINEMA
PHONES
STANDBY
/ON
9
SPEAKERS
A/B/OFF
■ Front panel/Face avant
3
0
TONE CONTROL
EDIT
PRESET/TUNING
2
l
FM/AM
A
h
1
A/B/C/D/E
PROGRAM
4
The circled numbers and alphabets correspond to those in the Owner’s Manual.
Les nombres et lettres dans un cercle correspondent à ceux du mode d’emploi.
00_Sheet_RHTR-6050_UC.book Page 1 Saturday, May 19, 2007 2:35 PM
B
EFFECT
STRAIGHT
2
l
3
PRESET/TUNING
C
DIRECT STEREO
SCENE
5
l
4
h
D
INPUT
h
MEMORY
7
E
AUDIO SELECT
F
TUNING AUTO/MAN'L
OPTIMIZER MIC
6
VIDEO
L
AUDIO
VIDEO AUX
R
VOLUME
USB
8
HTR-6050
UC
00_Sheet_RHTR-6050_UC.book Page i Saturday, May 19, 2007 2:35 PM
■ Remote control/Boîtier de télécommande
Y
A
B
POWER
POWER
TV
AV
MULTI CH IN
STANDBY
POWER
AUDIO SEL
SLEEP
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
M
N
O
P
TV CH
C
V-AUX
USB
AMP
TV INPUT
1
2
TV VOL
TV MUTE
D
E
F
SCENE
BAND LEVEL
TITLE
G
3
4
VOLUME
MENU
R
ENTER
H
S
DISPLAY
RETURN
Q
REC
I
FREQ/TEXT
J
K
L
EON
l
PROG h
1
2
MODE – PTY SEEK – START
ENHANCER STRAIGHT
3
8
T
U
ENT
V
4
DIRECT ST.
SUR.DECODE NIGHT
5
6
7
9
0
10
W
X
Printed in China
WK65650