Casio E-115 - Cassiopeia Color Pocket PC Specifications

(without price)
Pocket PC
E-125 (JX-650E)
AUG. 2000
E-125
INDEX
R
CONTENTS
1. MAIN FEATURES ---------------------------------------------------------------------------------- 1
2. SPECIFICATIONS ---------------------------------------------------------------------------------- 2
3. UNPACKING
3-1. Enclosed products and parts ------------------------------------------------------------- 4
3-2. Options ------------------------------------------------------------------------------------------- 4
4. GENERAL GUIDE and INITIAL SETUP
4-1. General Guide ---------------------------------------------------------------------------------- 9
4-2. Initial Setup ----------------------------------------------------------------------------------- 21
5. RESET OPERATION and BATTERY REPLACEMENT
5-1. Reset Operation and FULL RESET ---------------------------------------------------- 23
5-2. Battery Replacement ---------------------------------------------------------------------- 26
6. DATA COMMUNICATIONS
6-1. General ----------------------------------------------------------------------------------------6-2. Connection to PC --------------------------------------------------------------------------6-3. ActiveSync 3.1 synchronization PC LINK software ----------------------------6-4. BACKUP/RESTORE using ActiveSync 3.1 ----------------------------------------6-5. Card Backup Tool --------------------------------------------------------------------------6-6. Mobile Communication ------------------------------------------------------------------6-7. Infrared Communication ------------------------------------------------------------------
29
29
31
31
31
37
38
7. ADJUSTMENT ------------------------------------------------------------------------------------- 39
8. OPERATION CHECK
8-1. Preparation -----------------------------------------------------------------------------------8-2. How to install the diagnostic program ----------------------------------------------8-3. How to delete the diagnostic program ----------------------------------------------8-4. Operation check -----------------------------------------------------------------------------
43
43
45
46
9. TROUBLESHOOTING ---------------------------------------------------------------------------- 53
10. CIRCUIT BLOCK DIAGRAM ------------------------------------------------------------------- 55
11. WIRING DIAGRAM -------------------------------------------------------------------------------- 56
12. SCHEMATIC DIAGRAMS
12-1. Main block (1/3)~(3/3) ---------------------------------------------------------------------12-2. ROM block ------------------------------------------------------------------------------------12-3. Key block -------------------------------------------------------------------------------------12-4. USB cradle ------------------------------------------------------------------------------------
57
60
61
62
13. PCB VIEW (Main block) ------------------------------------------------------------------------- 63
14. DISASSEMBLY PROCEDURE ---------------------------------------------------------------- 66
15. PARTS LIST----------------------------------------------------------------------------------------- 70
16. EXPLODED VIEW
16-1. PCB ASSY and COMPONENTS --------------------------------------------------------- 75
16-2. OTHERS ---------------------------------------------------------------------------------------- 81
16-3. CRADLE ---------------------------------------------------------------------------------------- 84
* Windows is a registered trademark of Microsoft Corporation in the U.S.A. and other countries.
* i486 and Pentium are registered trademarks of Intel Corporation.
1. MAIN FEATURES
Visit the following CASIO Tokyo Web site whenever you want to obtain the information (Main Features,
Specifications, and so on)and the software concerning CASIO overseas products.
Address: http://www.casio.co.jp/English/
Visiting this homepage, you will see
the screen display as shown to the
right.
You can select CASIO overseas
products genre using this page.
When you want to obtain the
information concerning
CASSIOPEIA (EM-125 etc.), select
CASSIOPEIA.
However, select Business
Solution concerning EG-800.
You can obtain the significant and
available information (Main
Features, Specifications, FAQ, and
so on) and the application software
concerning overseas CASSIOPEIA
products.
When you visit overseas CASSIOPEIA directly, visit the following CASSIOPEIA Web site
Address: http://www.casio.co.jp/English/ce
You can visit CASIO America Web site (http://www.casio.com) selecting North America in this home
page also.
Overview (Quotation from above CASIO TOKYO Home page)
The newest PocketPC, CASSIOPEIA E-125 is a business companion that works with you 24 hours / 7
days a week.
Not only Pocket Word and Excel are included, CASIO Original Color PIM provides you a full schedule
management that synchronizes with your PC much easier.
For Mobile business Professionals, CF-Card TYPE II(320MB available) slot allows you to store heavy
load of work. An optional CF Camera Card let you capture still images and short video clips that would
make your presentation effective and professional. Also the 65,536 color TFT screen can help you
display all of your presentations and images clearly.
Main features
E-125 is the unit to which updated powerful devices and software for Pocket PC are applied. CPU is
VR4122. System clock is the high speed 150MHz. RAM Memory capacity is 32MB. TFT color (240 ×
320 dots) display is adopted. Type I and II CF cards are applicable as well as E-115. Therefore, MMC
card is not applicable to E-125.
OS is Windows CE 3.0. The Synchronization LINK software is ActiveSync 3.1.
—1—
2. SPECIFICATIONS
Model:
Display:
E-125
240 × 320 dots
TFT Color LCD (65,536 colors)
CPU:
VR4122
Memory:
16MB
Interfaces:
Serial:
RS-232C, 115.2 kbps max.
Infrared: IrDA Ver. 1.2
Range: 20 cm max.
USB (Client)
Card Slot:
Compact + Flash card, 3.3v type I/ type II
Headphone jack:
ø 3.5 mm stereo output
Accepts monaural earphone, stereo earphones/headphones
Power Supply:
Main:
Rechargeable battery pack JK-210LT (Lithium-Ion battery)
AC adapter (AD-C59200)
Backup: One CR2032 lithium battery
Power Consumption:
4.0 W
Approximate Battery Life (Normal Temperature)
Main:
(Actual time may be shorter due to conditions when charging.)
8 hours: Continuous input and data display at a ratio of 1:10,
with screen brightness at lowest possible level.
3 hours: Continuous communication using the optional
modem card (JK-711MC56, US and Canada only),
with screen brightness at lowest possible level.
• Even when the unit is turned off, small amounts of power are
required to retain memory contents, etc. This can cause
batteries to go dead even when you do not use the unit.
• The actual amount of operation time that can be expected
from batteries depends on operating conditions, settings, and
other variables.
Backup: 5 years: Main battery is charged or replaced immediately
after appearance of message to replace main
battery.
1 week: No battery replacement after appearance of
message to replace main battery.
Approximate Charge Time (Normal Temperature)
5 to 6 hours: Charge time is longer for the first charges after purchasing
the unit or installing a new battery pack.
Operating Temperature: 0°C to 40°C (32°F to 104°F)
Charging Temperature:
10°C to 35°C (50°F to 95°F)
Dimensions:
20H × 83.6W × 131.2D mm (3/4"H × 3 1/4"W × 51/8"D)
Weight:
Apprpximately 250 g (8.8 oz)
—2—
Current consumption:
NOTES:
1. When measuring these current, it is recommended to use the analog ammeter to make the
measurement easier due to protecting the ammeter from noises.
2. Make LCD display contrast the best (default) condition before measurement.
3. Measure under the ambient temperature range 15˚C~35˚C
Operation Mode
Input Voltage
Current consumption
Main menu of OPERATION
CHECK in this manual
Rechargeable Battery :
4.0 ± 0.1V
≤180mA
* POWER CONTROL of
OPERATION CHECK
Rechargeable Battery :
4.0 ± 0.1V
≤370mA
* POWER CONTROL of
OPERATION CHECK
AC Adapter : 5.9V ± 0.1V
≤370mA
Power/OFF
Rechargeable Battery :
4.0 ± 0.1V
≤2.5mA
Power/OFF
Lithium battery for Back-up
3.0 ± 0.1V
≤1.6mA
*Tapping 5 POWER CONTROL in the OPERATION CHECK Main Menu screen display, the following
display will appear.
Currently CPU clock : 150 MHz
VT Clock :
50 MHz
Push Action key to exit
Voltage Detectors:
Main (Rechargeable) Battery:
VDET1B : approximately 3.5 V (Low battery message)
VDET2 : approximately 3.2 V (Forced power OFF)
Back-up Battery:
VDETS : approximately 2.7 V (Low battery message)
Unit Alignment Condition for Data transfer using IrDA :
Length (L)
Angle (A)
L ≤ 20 cm
A ≤ 15˚
A
E-125
E-125
L
—3—
3. UNPACKING
Refer to PARTS LIST and EXPLODED VIEW in this manual concerning parts and products enclosed in
the unit.
Visit the following CASIO TOKYO Web site home page concerning options etc.
Address: http://www.casio.co.jp/English/ce/uk/product/em500_accessory.html
Note: GSM cable for MC-21 and Message Cam PCJ630AA01B can no be applicable to CASSIOPEIA
Pocket PC including E-125.
3-1. Enclosed products and parts
Refer to OTHERS and CRADLE in PARTS LIST along with EXPLODED VIEW in this manual concerning
enclosed parts and products. These products (parts) can be supplied as spare parts.
Some spare parts (USB cradle, stylus and so on) are also marketed as options.
Refer to above CASIO TOKYO Home page concerning these parts.
Although the following parts (CD-ROMs) are enclosed in the unit, these CD-ROMs can not be supplied
as spare parts . Because these CD-ROMs are directly supplied to the factory from manufacturers.
Media Player Upgrate CD-ROM (CDJ650E07A) will be not enclosed after 30000 mass production.
Enclosed parts which
can not be supplied as
spare parts
CD-ROM/AUDIBLE
Code No.
Specification
Note
3335 6902
CDJ530AA04A
CD-ROM/AOL
1002 7680
CDJ580EA04A
Audible CD-ROM
Direct supply from Microsoft Corp.
AOL CD-ROM
Direct supply from AOL
3-2. Options
Although the following products are not enclosed in the unit, these products are available to use wholly
the unit.
Refer to the following home page also.
Adress (URL) : http: //www.casio.co.jp/English/system/pa/products/ht/eg800_option.html
■ Car adapter and Charger
1. Car adapter JK-210CA
Attach it directly to the E-125 or to the E-125 cradle to provide power and recharge the batteries.
INPUT: 12~24V DC/OUT: 5.9V 2A DC
Fuse (5A) is assembled in JK-210CA.
2. Rapid Charger CHC42110UU (Japan, US and Canada only)
INPUT: 100~240V AC/OUTPUT: 4.2V 1.1A DC
Power cord CBL-K799-AC-JU will be enclosed in CHC42110UU.
This charger is now applicable to Japan, US and Canada only due to the electric safety recognition
(Japan safety standard, UL, FCC and CSA) licenses. The other licences are not obtained now.
■ Communication
1. RS-232C Cradle JK-512CR
Although USB Cradle is enclosed in the unit, RS-232C Cradle is not enclosed.
If there are no USB port onto your PC, it is recommended to use this cradle.
2. USB Cable JK-582CA
When you want to connect directly CASSIOPEIA to PC’s USB port without the cradle, use this
cable. The line driver/receiver is assembled onto the cradle to reject the internal/external noises
and malfunction at the time of data transfer.
Therefore, it is recommended to use the cradle if possible.
—4—
3. RS-232C Cradle JK-580CA
The cable connected to RS-232C port on PC.
If is recommended to use the cradle if possible as described above.
4. CDMA digital phone connection cable JK-541CA (US and Canada only)
Refer to page 26 in the Hard Manual for E-125 or GENERAL GUIDE in this manual concerning the
configuration etc.
5. Modem JK-720MA (US and Canada only)
Connecting CASSIOPEIA to the analog telephone line.
To telephon
To E-125
From AC adapter
DCIN 5.9V
6. Modem card JK-711MC56 (US and Canada only)
■ CF camera card JK-710DC
Visit the following CASIO TOKYO Home page.
http://www.casio.co.jp/English/ce/product/mobile_canera.html
The following descriptions are the quotation from
above home page.
By installing an optional Digital Camera Card
(350,000 pixel), you can take digital snapshots
and movies. Movies are stored in the CASIO
Format Movie File (CMF file) and still-photos are
stored in the JPEG file.
Can be use as an image memo pad.
—5—
Special Features
Album Function
Can be used as
an image memo pad.
Can put date, place
and comments
beside each snaps.
Can put name
on the each albums.
Movie Clip
Download some of the movies
captured from the JK-710DC.
• To see these movies, you need to
download the desktop player.
Get it here
Specifications
• 640 X 480 Image Display
• Album Capabilities
• Swivel Lens
• Weight: 1.6 ounces
• Movie Images in CMF format
• Thumbnail Indexing
• Memory for Storage
• 45 Minute Battery Life
• Still Images in JPEG format
■ Screen protectors JK-811PS5
Use this sheet to prootect the touch panel from the scratch and other damages.
5 sheets are included.
■ CompactFlash Card
Refer to page 15 in this manual.
—6—
■ Enhance your device (Quotation from CASIO TOKYO Home page)
You will find a lot of different products with new products added. So whether you're looking to add
memory to your device, or purchase a new modem - we've got what you need.
Please make sure CASIO does not guarantee the reliability of these peripherals.
Please ask questions regarding the peripherals to each manufacture you visit from this page.
To hardware/accessory manufacturers.
Socket Communications, Inc.
Socket's Digital Phone Card
Socket In-Hand Scan CF+ Card
CF+ Low Power Ethernet Card
Pretec Electronics Corporation
56K CompactModem
CompactSerial
CompactSSFDC
CompactFlash™ Type I
Capacity: 4, 8, 16, 32, 48, 64, 96, 128MB
CompactFlash™ Type II
Capacity: 80, 160, 320MB
CompactGPS
—7—
MarWare, Inc.
SportSuit II
SportSuit III
CEO Plus
—8—
4. GENERAL GUIDE and INITIAL SET UP
4.1. General Guide
Charge indicator (Amber/Green)
Lights amber when the battery pack is
charging and turns green when full
charge is achieved.
Stereo headphone jack
For connection of a
commercially available
earphone/headphones (ø3.5mm)
Card slot
Stylus
Indicator lamp (Red)
Alerts you to alarms and
warning.
Power button
Turns power on
and off.
Touch screen
Perform operations and input
data by tapping and writing
directly on the screen.
Start button
(Program button)
Press to display
the Start menu.
• Menu
(Launcher)
• Contacts
• Calendar
Action control
See “About the
[Action] Control”
on the next page.
Speaker
Record button
(Program button)
Voice memo recording is
activated as long as you
hold down this button.
Program buttons
Press to launch the
assigned program.
The programs
shown here are the
initial default
settings.
Cursor button
Moves the cursor around
the screen.
Microphone
Infrared port
AC adapter terminal
—9—
Card lock switch
If the inserted card has
a lock, this switch locks
the card in place so it
does not come out
accidentally.
Backup battery cover
RESET button
Main battery cover
Battery cover switch
Serial connector
For connection of the cradle,
the CASSIOPEIA USB
cable, or the RS-232C serial
cable.
About the [Action] Control
Operations can be performed by pressing and rotating the [Action] control.
Rotating the [Action] control
performs operations similar to
the up and down arrow keys
of a computer keyboard.
Pressing the [Action] control
performs an operation
similar to the Enter key of a
computer keyboard.
See Pocket PC online help for information about using the [Action] control with each
application. The text in the online help indicates an [Action] control press operation
as “Action,” and an [Action] control rotate operation as “Up/Down control.”
— 10 —
Using the Stylus
Data input and virtually all other operations are performed using a stylus, which is
housed inside the stylus holder in the higher right corner of the CASSIOPEIA.
The following defines the various operations that you can perform with the stylus.
Tap ......................Touch the screen once with the stylus to open items and select options.
Drag .................... Hold the stylus on the screen and drag across the screen to select text and images.
Drag in a list to select multiple items.
Tap-and-hold .......Tap and hold the stylus on an item to see a list of actions available for that item.
On the pop-up menu that appears, tap the action you want to perform.
Important
• Take care that you do not misplace or otherwise lose the stylus by always storing it in the stylus
holder when you are not using it.
• Take care to avoid breaking the tip of the stylus.
• Use only the stylus that comes with the CASSIOPEIA, or some other stylus type instrument* to
perform touch screen operations. Never use a pen, pencil, or other sharp writing implement.
*(with a soft, blunt point)
Recalibrating the Touch Screen
You should recalibrate the touch screen whenever touch screen response is bad, or when the operation
performed is different from the operation you expected when tapping on the touch screen.
To recalibrate the touch screen, press the [Action] control while holding down the [Power] button (or tap
, Settings, the System tab, and then the Align Screen). Next, follow the instructions that appear
on the screen.
Adjusting Display Contrast
Perform the following operations to adjust display contrast and make figures on the display darker or
lighter.
• Tap
and then Settings. On the System tab, tap Brightness. Follow the instructions on your
screen for adjusting the contrast.
• You can also adjust contrast by holding down [Action] and pressing the top of the cursor button to
make contrast darker, and the bottom of the cursor button to make it lighter.
Adjusting Display Brightness
Use the following operations to adjust display brightness to make it easier to read.
• Tap
and then Settings. On the System tab, tap Brightness. On the dialog box that appears,
tap the Brightness tab.
• While holding down the [Action] button, press the right side of the cursor button to make the
screen brighter, or the left side of the cursor button to make it dimmer.
— 11 —
Adjusting Auto Dimming Settings
1. Tap
and then Settings. On the System tab, tap Brightness.
2. On the dialog box that appears, tap the Auto Dim tab.
3. Follow the instructions that appear on the screen to make auto dimming settings.
• You can make separate auto dimming settings for battery power and AC adapter power by
checking the appropriate check box.
Changing Applications Assigned to the Program Button
• Tap and then Settings. On the Personal tab, tap Button, and then follow the instructions that
appear on the display.
• Button Assignment Utility makes it easy to assign CASIO Mobile Calendar to the
button and
CASIO Mobile Address Book to the
button. To use Button Assignment Utility, tap
,
Programs, Utility, and then Button Assignment.
Using the Cradle
The cradle provides quick and easy connection between your CASSIOPEIA and a
personal computer. CASSIOPEIA can also be powered from an AC power source when
it is placed on the cradle.
• The battery pack charges while the CASSIOPEIA is on the cradle.
Important
Make sure that CASSIOPEIA power is turned off before you place it onto or remove it
from the cradle.
Use the following procedure to place the unit onto the cradle.
1. Place the cradle on a desk or other flat, level surface.
2. Turn off the CASSIOPEIA.
3. Slide the CASSIOPEIA’s serial connector cover to open it.
4. Orient the CASSIOPEIA in relation to the cradle as shown in the illustration below.
— 12 —
5. Taking care to align the serial connector on the bottom of the CASSIOPEIA with the connector on
the cradle, lower the CASSIOPEIA into the cradle as shown in the illustration below.
Important
Make sure the CASSIOPEIA lowers securely into the cradle as far as it can go.
To remove the CASSIOPEIA from the cradle
1. Press the cradle’s eject button.
2. Slide the CASSIOPEIA straight up from the cradle.
— 13 —
Using the AC Adapter (Refer to PARTS LIST and EXPLODED VIEW in this manual concerning
AC adapter)
You can use the AC adapter to directly power the CASSIOPEIA or to supply power through the cradle.
The battery pack charges while the CASSIOPEIA is directly connected to a power source by the AC
adapter or while it is on the cradle.
■ Direct Connection
■ Cradle Connection
Warning
Use only the AC adapter that is specified for this unit. Use of another type of AC sadapter creates the
danger of malfunction and bursting of battery.
Important
• Power also will not turn on if the main battery loaded in the CASSIOPEIA is dead.
• Long term use of the AC adapter can cause it to become warm to the touch. This is normal and
does not indicate malfunction.
• Be sure to unplug the AC adapter from the power outlet whenever you are not using it.
• The AC adapter is designed for indoor use only. It should not be used outdoors.
— 14 —
Using a CompactFlash Card
Your CASSIOPEIA supports Type I and Type II CompactFlash Cards (3.3V).
At present, all CASIO CompactFlash Cards are Type I ones.
The following CASIO CompactFlash Cards have been released as OPTIONS.
CF-2V (2MB)/ CF-4V (4MB)/ CF-8V (8MB)/ CF-8X (8MB)/ CF-10V (10MB)/ CF-15V (15MB)/
CF-15X (15MB)/ CF-16X (16MB)/ CF-30X (30MB)/ CF-32X (32MB)/ CF-48X (48MB)/ CF-64X (64MB)/
CF-128X (128MB)/ CF-192X (192MB)
* Refer to UNPACKING in this manual concerning CF card also.
NOTE
Type I CF Card is different from Type II CF Card with thickness and configuration as shown below.
<Type I CompactFlash Storage Card Dimensions>
<Type II CompactFlash Storage Card Dimensions>
• Length and Width of Type I are the same as ones of Type II.
— 15 —
Important
• The card slot cover will not close when certain types of cards are in the slot. Remove the card slot
cover and keep it in a safe place so you can replace it when you remove the card.
• Gently but firmly slide the card into place as far as it will go, but do not force it. Forcing a card can
damage connectors. If you have problems inserting a card, pull it out and check to make sure it is
oriented correctly.
• We strongly recommend that you store all unsaved data you are inputting or editing before
performing this procedure.
• Sometimes, your CASSIOPEIA may not be able to detect a CompactFlash Card. This is indicated
when a program on the card does not start up normally. When this happens, remove the card,
reinsert it, and then press the CASSIOPEIA RESET button.
• Your CASSIOPEIA supports 3.3V CompactFlash cards only. Cards that can operate on 5.0V only
are not supported.
• Use of an IO card that requires large amounts of power can cause the CASSIOPEIA to restart
when CASSIOPEIA battery power is low.
1. Make sure your CASSIOPEIA is turned off.
• Press the [Power] button to turn off power.
2. Pressing upward at the point indicated in the illustration, slide the cover up to open it.
Important
Pull the cover out as far as it will
go and then swing it open.
Press upward here.
3. If there is already a card in the slot, remove it.
4. Slide the card you want to use into the card slot.
• Make sure the top of the card is facing towards the top of the CASSIOPEIA unit. A card that is not
oriented correctly will not slide all the way into the slot.
Top
Bottom
Carefully slide the card into the slot as far as it will go.
5. Close the card slot cover.
Removing the Card Slot Cover
Remove the card slot cover when using a card that protrudes from the slot when fully inserted.
To remove the cover, pull it up part way open, and then slide it from the unit as shown in the
illustration below.
Important
Handle the cover carefully
and do not force it! Using
too much force can cause
the cover hooks to break
off!
Replacing the Card Slot Cover
Reverse the above removal operation to replace the card slot cover.
— 16 —
Digital Phone Connection Cable
• U.S. and Canada: Use a cdma digital phone connection cable (JK-541CA).
• For a GSM type digital phone, use a commercially available cable that is compatible with the
CASSIOPEIA connector.
• After you connect the CASSIOPEIA to your digital telephone, you can dial up our Internet service
provider or company server.
The following shows how to connect the CASSIOPEIA to a digital telephone.
• Separately available
cable (D-sub 9-pin) for
your particular
telephone model,
available from your
phone manufacturer
• Optionally available
digital telephone cable
(9-pin)
• Commercially
available GSM
connecting cable
To disconnect the digital telephone cable from the CASSIOPEIA, squeeze the release buttons on the
sides of the connector and unplug it.
Important
• Make sure your CASSIOPEIA is turned off before connecting the digital telephone cable.
• See the Pocket PC User’s Guide for information about settings, operations, and precautions
when connecting to a company network or the Internet.
• Make sure you are in an area where your telephone signal is strong before trying to dial in to a
computer.
Data communication may not be possible if you are within an area with poor signal reception, even
though it is within the service area of your telephone service provider.
Also note that noise can cause errors and make communication impossible, even though the signal is
strong. If this happens, try again.
• Never unplug the cables or turn off power while data communication is in progress.
• You may not be able to establish a connection with another computer that is also using a portable
telephone for communication.
• Whenever you disconnect the digital telephone cable from the CASSIOPEIA, wait at least three
seconds before you connect it again. Disconnecting the cable and immediately reconnecting it
again can make subsequent data communications impossible.
• Disconnect the digital telephone cable from the CASSIOPEIA when you are finished with data
communication.
• See the documentation that comes with your digital telephone for information about its
operations.
— 17 —
About the Modem Adapter and Modem Card (U.S. and Canada Only)
The Modem Adapter (JK-720MA) and CompactFlash type Modem Card (JK-711MC56) make it possible
to use your CASSIOPEIA to access the Internet over an analog dial-up connection. See the documentation
that comes with the modem card for information about how to use it.
Important
Check to make sure that the battery pack is charged before using the modem adapter and modem card.
Low battery power can cause sudden interruption of communications, unstable communications, and
loss of data.
About the Digital Camera Card
Installing the optionally available CompactFlash type digital camera card (JK-710DC) makes it possible
for your CASSIOPEIA to record and playback both movies and snapshots. For full details on how to use
the digital camera card, see the documentation that comes with it.
Important
• Do not install the Mobile Camera application from the CD-ROM that comes with the digital camera
card (JK-710DC)! Your CASSIOPEIA will not operate properly with this version of Mobile Camera.
• When using the optionally available digital camera card (JK-710DC), be sure to install the Mobile
Picture & Video Player with Camera application from the CD-ROM that comes bundled with your
CASSIOPEIA.
Charging the Battery Pack
1. Install the battery pack into the CASSIOPEIA.
2. Attach the AC adapter to the cradle and place the CASSIOPEIA onto the cradle.
• Charging starts automatically as soon as you place the CASSIOPEIA onto the cradle.
• The charge indicator is amber while charging is in progress, and turns green when charging is
complete.
• It takes about five or six hours to reach full charge.
• You can use your CASSIOPEIA while the battery pack is charging.
Important
• Do not use the CASSIOPEIA while it is charging for the first time after you purchased it or for the
first time after you installed a newly purchased battery pack.
• If the battery pack does not achieve full charge after the normal charge time, unplug the AC adapter
from the CASSIOPEIA to stop charging.
— 18 —
Remove the CASSIOPEIA from the cradle after charging is complete.
The following illustration shows how to connect the AC adapter directly to the CASSIOPEIA for charging.
• Charging starts automatically as soon as you attach the AC adapter to the CASSIOPEIA.
• Direct connection charging conditions are the same as those described for cradle charging above.
— 19 —
Windows Media Player for Pocket PC
Use Windows Media Player for Pocket PC to listen to digital audio files.
To switch to Windows Media Player, tap
and then Windows Media Player.
Using Windows Media Manager for Pocket PC
Use Windows Media Manager for Pocket PC on the desktop computer to create digital audio files
in Windows Media format and to transfer audio content to your Pocket PC or storage card. With
Windows Media format, you can create high-quality audio for your Pocket PC without using large
amounts of Pocket PC memory.
You can transfer the following media formats to your Pocket PC for use with the Windows Media
Player: ASF (Advanced Streaming Format), WMA (Windows Media Audio), MP3 (MPEG Audio
Layer 3), and WAV (waveform).
Windows Media Manager is included in the Extras folder on the ActiveSync CD. You must install
Windows Media Manager on your desktop computer to copy and convert digital audio files.
* To Install Windows Media Manager to your PC, click wmmsetup.exe file Icon in the Media
holder in the Extras holder, and then operate your PC according to messages on the screen.
It is recommended to open and read readme.txt file in this Media holder.
Completing above installation, Windows Media Manager will be added to the start program
menu of your PC.
* Welcome To Windows Media. wma file will be previously installed to My Documents holder in
the unit.
— 20 —
What is Packaged Content?
Packaged content is digital music that has been encrypted for distribution to prevent unauthorized
access to copyrighted content. Windows Media Player for Pocket PC cannot play packaged
content without a valid license. First use Windows Media Player on the desktop computer to
obtain packaged content that has a license that allows transferring the content to your Pocket PC.
Then use Windows Media Manager for Pocket PC to transfer the packaged content and its license
to your Pocket PC or storage card. To successfully transfer packaged content, your Pocket PC or
storage card may require a hardware serial number.
You can play packaged content until the license expires. During license download, you will be
informed of the terms of the license. License terms can be for an unlimited time, a set amount of
time, or a set number of playbacks. A license can support content being copied to a Pocket PC or
storage card an unlimited number of times or one time only. Terms are entirely dependent on the
content provider.
Using the Playlist Manager
Use the playlist manager to set the track playback order. All My Music is the default playlist. It
contains all digital audio files available for playback on your Pocket PC and storage card. To see a
list of recently selected playlists, tap Select Playlist. To create or edit playlists, tap All Playlists.
Tap and hold a track or playlist to perform actions such as copying, moving, and deleting.
For more information on using Windows Media Player, tap
and then Help.
4-2. Initial Setup
After you first unpack your CASSIOPEIA, perform the following initial setup
procedure before using it for the first time.
1. Load the main battery (rechargeable battery pack).
Important
Be sure to use the AC Adapter to charge the battery pack before doing anything else.
Your CASSIOPEIA will not operate correctly if you load the backup battery before
charging the battery pack.
2. Use the AC Adapter to charge the battery pack.
3. Load the backup battery.
4. Press the [Power] button.
• After a few moments the welcome screen appears.
5. Follow the steps in the Welcome Wizard.
— 21 —
6. When finished, you’ll see the Today screen.
• See “Pocket PC Basics” at the back of Quick Start Guide for information about the Today screen
and other Pocket PC Basics.
• You also need to install ActiveSync before you can communicate with a desktop computer.
Important
• If the touch panel does not respond when you tap it or if nothing appears on the display, try
performing a full reset. If this does not restore proper operation, remove the main battery and the
backup battery and wait for about five minutes. Reload the main battery first and then the backup
battery, and perform the above procedure again from step 4.
• If the message “A problem with memory contents has been found...” appears on the display,
perform a full reset.
— 22 —
5. RESET OPERATION and BATTERY REPLACEMENT
5-1. Reset Operation and FULL RESET
Resetting the Unit
“Reset” is similar to a computer reboot. Performing a reset deletes any data that is in the process of
being input or edited, without yet being saved. Data stored in memory and all settings, however, are
retained.
Perform the reset operation whenever the unit fails to operate correctly due to operational error or some
other abnormality. Any of the following symptoms indicate that reset is required.
• Failure of the unit to respond when the screen is tapped or a button is pressed.
• The hourglass icon remaining on the screen.
Performing a Reset
1. Use the stylus to press the RESET button.
• The unit performs a reset followed by a memory check operation.
If no data error is found, the following two screens appear on the display in succession.
• Startup screen
• Desktop
2. Normal unit operation is possible after the desktop appears.
• Memory data and settings are retained when you reset the Pocket PC.
Important
If the above operation does not solve the problem, perform a full reset.
Memory Error Message
If the memory check operation that the unit performs when the RESET button is pressed detects a data
error, the following message appears on the screen instead of the startup screen.
“A problem with memory contents has been found. Press [Action] to continue with the reset
procedure, which restores normal system operation.
Note that if the system determines that user memory cannot be repaired, it will delete all user
data currently in memory.
See the User’s Guide for details about initializing memory.”
This message indicates that the memory error is fatal and so recovery is impossible.
Press the [Action] control to execute a full reset (memory initialize), which deletes all data stored in
memory.
• Pressing the [Action] control should display the Startup screen followed by the touch screen
calibration screen. Perform steps 5 through 6 under “Initial Setup” to set up the unit.
• If pressing the [Action] control returns to the desktop without displaying the startup screen first, see
the following explanation for the procedure you need to follow.
What to do if the startup screen does not appear when you press the [Action] control
Even though the desktop appears when you press the [Action] control, there is still a data error in
memory and you have to perform a full reset (memory initialize). Before you do, however, there is the
chance that some of the data in memory can be recalled and even transferred to a computer. Try recalling
the data you need before performing the procedure described on the next page to perform a full reset.
— 23 —
Important
Do not use the ActiveSync backup function to back up data to a computer when you suspect a data error.
Doing so may also include the corrupted data that is causing your problem, which means the problem
will reappear when you restore the data.
Full Reset (Memory Initialize)
Full reset (memory initialize) deletes all data, and resets all unit parameters to their initial defaults.
The following are conditions when you should perform a full reset.
• When you want to delete all memory data and return unit settings to their factory defaults
• When you forget your password and need to clear it
• When a data error causes operational problems
• Appearance of the message: “A problem with memory contents has been found...”
Performing a Full Reset
Important
• The following procedure deletes all data in memory. Be sure that data is backed up or that you no
longer need it before performing the following procedure.
• If there is a CompactFlash Card in the CASSIOPEIA’s slot, remove the card before performing the
full reset.
1. Make sure that unit power is turned on.
2. While holding down the [Power] button, use the stylus to hold down the RESET button for about
two seconds.
• This causes the following message to appear on the display screen.
“Proceeding with this operation initializes memory. Press [Action] to proceed or [Record] to
cancel.”
3. Press the [Action] control.
• This causes the following message to appear on the display screen.
“Proceeding with this operation deletes all data stored in memory. Press [Action] to proceed or
[Record] to cancel.”
4. Press the [Action] control again.
• This starts the full reset operation, which deletes all data in memory.
• Pressing the [Action] control displays the Startup screen. Perform steps 5 through 6 under “Initial
Setup” to set up the unit.
You can abort the full reset operation while the messages in steps 2 and 3 are on the display by pressing
the [Record] button.
Errors Following a Full Reset
Either of the following two conditions can cause errors to continue, even after you perform a full reset.
• Hardware defect
• System problem caused by failure by you to correctly perform the reset procedure before using the
unit for the first time
If you suspect that the problem is being caused because you did not properly reset the unit before using
it for the first time, perform the following procedure.
This should correct the problem.
• Perform the following procedure if your CASSIOPEIA remains locked up even after you perform a
full reset.
— 24 —
Important
• The following operation deletes all data in CASSIOPEIA memory.
• If you previously backed up your CASSIOPEIA data to your desktop computer hard disk or a
CompactFlash card, you will be able to restore the data after performing the following operation.
• If backed up data includes data that is the cause of the original problem, your CASSIOPEIA may
start malfunctioning again after data is restored. In this case, you will not be able to use the backed
up data.
• To protect against backing up corrupted data that can cause problems when restored, first
synchronize Pocket Outlook program data between your CASSIOPEIA and desktop computer.
Next, use drag and drop to copy other files to you computer. See ActiveSync Help for information
about synchronizing data and copying files.
1. Remove both the main battery and the backup battery from the CASSIOPEIA.
2. Wait for about five minutes.
3. Reload the main battery.
• Be sure to load the main battery first. The CASSIOPEIA will not operate properly if you load the
backup battery first. If you inadvertently load the backup battery first, start over from step 1 above.
4. Attach the AC adapter and charge the battery pack.
5. Reload the backup battery.
6. Make sure the battery cover switch is in the LOCK position.
7. Wait for about five seconds and then press the [Power] button to turn on your CASSIOPEIA.
• Turning on power displays the startup screen, following by the touch panel calibration screen.
8. Follow the instructions that appear on the screen to make initial settings.
9. After setting up your CASSIOPEIA, turn it off.
• After completing the above procedure, you can restore data you have backed up on your desktop
computer hard disk or CompactFlash card. See ActiveSync Help for information about restoring
backed up.
• See the Card Backup Tool manual (PDF file) on the CASSIOPEIA Application CD-ROM for
information about using the Card Backup Tool program to restore data from a CompactFlash card.
— 25 —
5-2. Battery Replacement
Batteries
Your CASSIOPEIA is powered by a dual power supply that consists of a main battery (rechargeable
battery pack) and a backup battery (CR2032 lithium battery).
• We recommend that you use the Power Properties to keep informed about the current levels of
your main and backup batteries. See the separate Pocket PC User’s Guide and Pocket PC online
help for more information about this properties.
Important
The following messages appear whenever battery power drops below a certain level.
Main Battery
Recharge the battery pack as soon as possible after the following message appears.
“Main Batteries Very Low
To prevent possible data loss, replace or recharge your main batteries according to the owner’s
manual.”
Backup Battery
Replace the backup battery as soon as possible after the following message appears.
“Backup Battery Very Low
To prevent possible data loss, replace or recharge your backup battery according to the owner’s
manual.”
• You can monitor the current battery power level accessing Power Properties or by checking the
battery icon in the command bar of the Today screen.
• Whenever the low battery warning message appears, especially if it appears right after you turn on
power, follow the instructions that appear on the screen and replace batteries as soon as possible.
Continued use under low battery power can cause unstable performance of your Pocket PC.
• Data stored in memory can be lost if you continue operation after the low battery message appears
or if you incorrectly load batteries. Be sure to always back up important data on your desktop
computer hard disk or on a CompactFlash card. See ActiveSync Help for information about backing
up files to a desktop computer.
• See the Card Backup Tool manual (PDF file) on the CASSIOPEIA Application CD-ROM for
information about backing up data to a CompactFlash card for information about using the Card
Backup Tool program to back up data to a CompactFlash card.
• Never remove the main battery and backup battery from the CASSIOPEIA at the same time. Doing
so causes all data stored in memory to be deleted.
• Should the main battery and the backup battery both require replacement, be sure to always
replace the main battery first.
• Use the rechargeable battery pack for the main battery and a CR2032 lithium battery for the
backup battery. Never use any other type of batteries.
If unit power turns off due to insufficient power, the following warning message appears on the display
the next time you turn on unit power.
“Warning
Due to high current demand by the hardware, the system powered down in order to protect
memory contents...”
If unit power turns off due to sudden power drain by a CompactFlash card, the following warning message
appears on the display the next time you turn on unit power.
“Warning
Due to high current demand by the card, the system powered down in order to protect memory
contents...”
— 26 —
Important
Be sure to observe the following important battery handling precautions. Failure to do so can cause
batteries to leak, resulting in damage to surrounding items and create the danger of fire and electrical
shock.
• Always make sure that the positive (+) and negative (–) poles of the batteries are oriented correctly.
• Use only the types of batteries specified for use with this unit.
• Charge the battery pack in an area where the temperature is between 10˚C (50˚F) and 35˚C (95˚F).
Charging in areas that are very cold or exposed to direct sunlight can cause deterioration and
leaking of the battery pack.
• To avoid deterioration and leaking, the battery pack is designed to discharge even when you do not
use the CASSIOPEIA. Be sure to recharge the battery pack at least once every three months,
regardless of how much you use the CASSIOPEIA during that time.
• A battery pack that loses power too quickly after it is charged is probably near the end of its service
life. In such a case, you have to purchase a new battery pack.
Replacing the Main Battery
1. Make sure your CASSIOPEIA is turned off.
• Press the [Power] button to turn off power.
2. Turn the CASSIOPEIA over.
3. Slide the battery cover switch to MAIN, and then remove the main battery cover.
4. Pull on the tape to raise the main battery.
5. Remove the main battery and then load a new battery pack.
• Make sure that the battery pack is oriented correctly.
• When you load the battery pack, make sure the end of the tape is sticking out above the battery
pack.
6. Replace the main battery cover.
7. Slide the battery cover switch to LOCK.
— 27 —
Replacing the Backup Battery
Important
• Never remove the main battery and backup battery from the CASSIOPEIA at the same time. Doing
so causes all data stored in memory to be deleted.
• Should the main battery and the backup battery both require replacement, be sure to always
replace the main battery first.
• Be sure to replace the backup battery as soon as possible whenever the following message
appears on the display: “Backup Battery Very Low To prevent possible data loss, replace or
recharge your backup battery according to the owner’s manual.”
1. Make sure your CASSIOPEIA is turned off.
• Press the [Power] button to turn off power.
2. Turn the CASSIOPEIA over.
3. Slide the battery cover switch to BACK UP, and then remove the backup battery cover.
Battery cover switch
4. Remove the old battery.
5. Wipe off a new lithium battery (CR2032) with a dry cloth, and load it into the CASSIOPEIA.
Make sure the positive side is facing up, so you can see it.
6. Replace the backup battery cover.
7. Slide the battery cover switch back to LOCK.
— 28 —
6. DATA COMMUNICATIONS
6-1. General
Performing Initial Setup and FULL RESET, data saved in the unit will be deleted.
Performing MEMORY BACKUP/RESTORE and CARD BACKUP TOOL Operations described in this
Chapter, save these data to PC and CF card before performing iInitial Setup and FULL RESET.
The following data communications are mainly applicable to E-125.
1. Between PC and E-125 using Activesync 3.1 software
2. Between CF card and E-125
3. Between Mobile phone and E-125
4. Between two E-125 units using IrDA
5. Between notebook-sized PC and E-125 using IrDA ports
6. Between E-125 (lower 20 pin connector) and Modem JK-720MA (U.S. and Canada only)
Refer to UNPACKING and GENERAL GUIDE in this manual concerning these communications.
6-2. Connection to PC
Connecting the Cradle to a Computer
The cradle has a USB cable for connection to a personal computer. Connect the end of the cable to a
USB port of the computer to which you want to connect.
Important
• See “Required System Configuration” on the later page for details on the type of computer system
required for use with the cradle.
• The above illustration is one example of possible connection configurations. The locations and
layouts of USB ports vary from computer to computer. See the documentation that comes with your
computer for full details on connecting cables to it.
• Note that after connecting the cradle to your computer, you also need to make certain ActiveSync
settings on your computer to enable data transfers. See the ActiveSync Help for details about
setting up and using ActiveSync.
— 29 —
Using the CASSIOPEIA USB Cable
You can use the CASSIOPEIA USB cable to connect the CASSIOPEIA directly to a computer.
Important
• See below “Required System Configuration” for the computer system that is required for direct USB
connection.
• The illustration below is just one possible connection configuration. The location and layout of USB
ports vary from computer to computer. See the documentation that comes with your computer for
full details on connecting cables to it.
• You must have ActiveSync installed on your computer in order to exchange data with the
CASSIOPEIA over a USB connection. See the Pocket PC User’s Guide for information on installing
and using ActiveSync.
To connect to a computer using the CASSIOPEIA USB cable
1. Plug the USB cable into the USB port of your computer.
2. Turn off your CASSIOPEIA.
3. Connect the other end of the USB cable to your CASSIOPEIA.
USB port
CASSIOPEIA USB cable
Required System Configuration
The minimum system configuration required for running ActiveSync
®
3.1 is described below.
®
ActiveSync 3.1 System Requirements
• Microsoft ® Windows ® 2000, Windows NT ® Workstation 4.0 with Service Pack 3 or greater, or
Windows 95/98. (U.S. version)
• Desktop computer with a Pentium processor for Windows NT (166MHz required for Windows 2000)
• Desktop computer with a 486/66 DX or higher processor (Pentium P90 recommended) for Windows
95/98
• 16MB of memory for Windows 95/98 (more memory will give improved performance) or Windows
NT Workstation 4.0 (32MB recommended for Windows NT, 64MB recommended for Windows
2000)
• Hard disk drive with 10 to 50MB of available hard disk space (actual requirements will vary based
on selection of features and user’s current system configuration)
• Available 9 or 25-pin communications port (adapter required for 25-pin communication port),
Infrared port, or USB port (available for Windows 95/98 or Windows 2000 only).
• One CD-ROM drive
• VGA graphics card or compatible video graphics adapter at 256 color or higher
• Keyboard
• Microsoft Mouse or compatible pointing device
PC Companion Device Requirements
• Handheld PC: Windows CE Handheld PC versions 2 and 3 with Windows CE Core System version
2.0 or greater
• Palm-size PC: All models and versions
• Pocket PC: All models and versions
— 30 —
Options for Windows 2000, Windows NT Workstation 4.0 or Windows 95/98
• Audio card/speakers for sound
• Microsoft Office 95 or Microsoft Office 97 or Microsoft Office 2000
• Modem for remote synchronization
• Ethernet LAN connection for remote synchronization
Requirements for Mobile Channels or Mobile Favorites Support
Microsoft Internet Explorer 4.0 or higher. Internet Explorer 5.0 is included on the CD, which requires 5698MB of hard disk space.
Requirements for Microsoft Outlook ® 2000
Microsoft Outlook 2000 requires 153 MB of disk space for a full installation. 24 MB system RAM
recommended.
Note
• Different minimum system requirements are required when using the applications included on the
CASSIOPEIA Applications CD-ROM. See the documentation contained on the CD-ROM for full
details.
• The cradle that comes with your CASSIOPEIA is designed for USB connection only.
If your computer does not have a USB port, you will need to purchase the separate serial
connection cradle (JK-512CR) or the serial connection cable (JK-580CA), which allows direct
connection between the CASSIOPEIA and your computer's serial port.
Important
• When installing ActiveSync on a computer, check to make sure that the specified COM port number
correctly indicates the serial port to which the cradle is connected.
• Some laptop and sub-compact computers with built-in infrared ports and modems are initially
configured so the COM port is not always used as a serial port. In such a case, you must change
the setting so the COM port is always used as a serial port.
See the documentation that comes with your computer for full details on COM port numbers and
settings.
6-3. Avtivesync 3.1 synchronization PC LINK software
Refer to 5. DATA TRANSFER in the Service Manual for E-115 concerning the installation etc. USB
(Universal Serial Bus) port on PC is applicable to ActiveSync 3.1 as described in 1.MAIN FEATURES in
this manual.
6-4. BACKUP/RESTORE using ActiveSync 3.1
Refer to 5. DATA TRANSFER in the Service Manual for E-115 also.
You can perform this operation according to this chapter as well as BACKUP/RESTORE between PC
and E-115.
Be sure to protect the important data from data disappearance and collapse using this function.
6-5. Card Backup Tool
Refer to CASIO TOKYO home page.
Prepare a CF card before this operation.
Trademarks
Microsoft, Windows, and Windows NT are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
All other product and company names mentioned herein may be the trademarks or their respective
owners.
— 31 —
• The contents of document are subject to change without notice.
• In no event shall CASIO COMPUTER CO., LTD. be liable to anyone for special, collateral,
incidental, or consequential damages in connection with or arising out of the purchase or use of
these materials. Moreover, CASIO COMPUTER CO., LTD. shall not be liable for any claim of any
kind whatsoever against the use of these materials by any other party.
• This manual and the software it describes are owned by CASIO COMPUTER CO., LTD. The
structure, organization, and code of the software are the valuable trade secrets of CASIO.
• The operations described in this manual assume that you are already familiar with the basic
operation of Windows CE. See the documentation that comes with Windows CE for full details on
its operation.
• Sample displays shown in this manual may differ somewhat from the displays actually produced by
the product.
Copyright Notice
No part of this publication may be reproduce, transmitted, transcribed, stored in a retrieval system, or
translated into any human or computer language, in any form or by any means, without the express
written permission of CASIO COMPUTER CO., LTD.
Copyright 2000 CASIO COMPUTER CO., LTD. All rights reserved.
■ Introduction
Card Backup Tool lets you quickly and easily back up your CASSIOPEIA memory data to a memory
card. Backed up data can be used to restore your system should it start to malfunction due to some data
error.
Backed Up Data
Card Backup Tool backs up the following three types of data in CASSIOPEIA memory.
• Files
Files are created using Notes, Pocket Excel, Pocket Word, and other applications and add-on
programs. Files transferred from your desktop computer to the CASSIOPEIA are also backed up.
• The Registry
The registry contains setup data for Windows CE and built-in applications.
• Database Data
Database data is Calendar, Contacts, Tasks, and Inbox data.
Password
Backed up data can be protected by a password. By assigning a password to backed up data, you
protect against unauthorized access because the data cannot be restored unless the correct password
is entered first.
Time Required for Backup
Depending on how much data you are backing up (or restoring), the backup operation can take anywhere
from about 10 seconds to a number of minutes. Backing up 4MB of data, for example, takes three or four
minutes. To check how much data is on your system, tap
, Settings, System tab and then Memory.
On the dialog that appears, tap the Main tab. The value under Storage indicates how much data is
stored in memory. See the Pocket PC User's Guide and CASSIOPEIA online help for more information.
Important!
The restore operation can take a very long time if you do not have enough storage memory allocated.
When this happens, quit the restore operation, increase the size of the storage memory, and then try the
restore operation again.
— 32 —
■ Using Card Backup Tool
This section provides details about the backup and restore operations you can perform using Card
Backup Tool. Be sure to read the following precautions before using Card Backup Tool for either backup
or restore.
Read this first!
• Always reset your CASSIOPEIA before backing up or restoring data. Make sure you perform a
reset operation. Do not perform a full reset operation! See the separate Hardware Manual for
information about how to reset your CASSIOPEA.
• Be sure to power your CASSIOPEIA with the AC adapter whenever performing a backup or restore
operation.
• If main battery or backup battery power is low when you start a backup or restore operation, a
warning message appears and the backup or restore operation is cancelled. Before starting a
backup or restore operation, charge the battery pack or load new batteries.
• Do not perform any button or screen operations on the CASSIOPEIA while a backup or restore
operation is in progress. Do not touch the CASSIOPEIA at all until the backup or restore operation
is complete.
• Files and other data are automatically compressed before being stored in CASSIOPEIA memory.
Make sure the memory card you are using for backup has enough unused space to store the data.
Backing Up Data
Use the following procedure to back up data. Make sure you read the precautions under "Read this first!"
before starting.
To back up data
1. Connect the AC adapter to your CASSIOPEIA.
2. Reset the CASSIOPEIA.
3. Insert a memory card with sufficient free space to store the backup data into the CompactFlash
Card slot of the CASSIOPEIA.
4. Tap
, Programs, Utility, and then Card Backup.
• This starts up Card Backup Tool and causes the dialog shown below to appear.
— 33 —
5. Tap Backup now.
• This causes the dialog shown below to appear.
• If you do not wish to assign a password, go to step 6 without inputting
6. Tap Yes to start the backup or No to close the dialog without backing up anything.
• The "Backup in Progress" dialog appears while the backup operation is being performed.
• The message "Backup complete!" appears on the display after the backup operation is complete.
7. After backup is complete, tap OK to quit Card Backup Tool.
Note
If the backup operation is interrupted or unsuccessful for any reason and there is a previous backup file
on the memory card you are using, the previous file remains intact on the card.
To interrupt a backup operation
1. Tap the Cancel button on the message box that is on the screen while a backup operation is in
progress.
• This causes the message "Do you really want to cancel?" to appear.
2. Tap Yes to cancel the backup operation or No to resume it.
Quitting Card Backup Tool
• Tapping the OK button on the dialog box that appears at the end of a backup operation
automatically quits Card Backup Tool.
• To quit Card Backup Tool without performing a backup operation, tap the Cancel button.
Restoring Data
The following applies whenever you perform a restore operation.
• If the same file or registry data exists in both CASSIOPEIA memory and on the memory card, the
data in CASSIOPEIA memory is overwritten with the data on the memory card.
• Any files or registry data in CASSIOPEIA memory that is not on the memory card is left as-is.
• Calendar, Contacts, Tasks, and Inbox data in CASSIOPEIA memory is all overwritten with the
corresponding data from the memory card.
— 34 —
• To return CASSIOPEIA to the exact status it was when you backed up the data, perform a full reset
before restoring the data. See the separate Hardware Manual for information about the full reset.
Use the following procedure to restore data. Make sure you read the precautions under
"Read this first!" on page 33 before starting.
To restore data
1. Connect the AC adapter to your CASSIOPEIA.
2. Reset the CASSIOPEIA.
3. Insert the memory card that contains the data you want to restore into the CompactFlash Card slot
of the CASSIOPEIA.
4. Tap
, Programs, Utility, and then Card Backup.
• This starts up Card Backup Tool and causes the dialog shown below to appear.
— 35 —
5. Tap Restore now.
• This causes the dialog shown below to appear.
6. Tap Yes to start the restore or No to close the dialog without restoring anything.
• The "Restore in Progress" dialog appears while the restore operation is being performed.
• The message "Restore complete!" appears on the display after the restore operation is complete.
7. After restore is complete, tap OK to quit Card Backup Tool.
8. Reset your CASSIOPEIA again.
Deleting a Backup File
You can use the following procedure to delete the backup files you created using Card Backup Tool.
Delete a file when you no longer need it, when you want to free up space on a memory card, etc.
To delete a backup file
1. Insert the memory card that contains the backup file you want to delete into the CompactFlash
Card slot of the CASSIOPEIA.
2. Tap
, Programs, Utility, and then Card Backup.
• This starts up Card Backup Tool.
3. Tap Backup File Delete.
• This causes the dialog shown below to appear.
4. Tap Yes to delete the backup file or No to close the dialog without deleting anything.
— 36 —
6-6. Mobile communication
Refer to UNPACKING and GENERAL GUIDE in this manual.
Supports WAP, SMS, E-mail
and Internet
when used in combination with a GSM mobile phone.
MTDS Web Site
*Internet access requires an account with
an Internet service provider.
note
Communication systems differ from country-to-country.
Contact your local CASIO retailer for full details about
communications that are supported in your area.
Pocket Internet Explorer
Mobile E-Mailer
Mail Setup Tool
Mail Setup Manager for CASSIOPEIA
Mail Setup Tool is a special application that
simplifies troublesome settings you need to
make in order to send and receive e-mail on your
Pocket PC.
This application lets you copy your computer's
e-mail account settings to your Pocket PC for
automatic configuration of the Pocket PC e-mail
settings.
Bonus Software
Bonus Software
— 37 —
6-7. Infrared Communication
The infrared port of this unit can be used to exchange data with another CASSIOPEIA, or with another
device equipped with infrared communication capabilities. Remember that the two infrared ports must
be pointed directly at each other when performing communications. The distance between the two infrared
ports must be less than 20 cm.
See the Pocket PC User’s Guide for full details on performing infrared communications.
For infrared data communications with another device, the other device must conform with IrDA 1.2
standards, and it must specifically support infrared data communication with a CASSIOPEIA.
Important
• Take care so either of the units does not move while infrared data communications are in progress.
• Infrared data communications may be impossible under strong sunlight or inverter type fluorescent
lighting.
• Infrared data communication problems can be caused by the distance between the two ports, the
angle between the two ports, outdoor sunlight, and low batteries.
• Dirt and dust on the infrared port surface can cause communications errors and other problems.
Use a soft, dry cloth to wipe the port clean of dirt and dust.
Transfer Items Using Infrared
Using infrared (IR), you can send and receive information, such as contacts and appointments, between
two Windows-powered Pocket PCs.
To send information
1. Switch to the program where you created the item you want to send and locate the item in the list. If
you want to send more than one item, drag the stylus across the items you want to send.
2. Align the IR ports so that they are unobstructed and within a close range.
• The two infrared ports should be within about 20cm from each other.
3. Tap and hold the item, and tap Send via Infrared on the pop-up menu.
You can also send items, but not folders, from File Explorer. Tap and hold the item you
want to send, and then tap Send via Infrared on the pop-up menu.
To receive information
1. Align the IR ports so that they are unobstructed and within a close range.
2. Tap
, Programs, and then Infrared Receive.
You can also receive items from Tasks, Contacts, Calendar, and Notes by tapping Tools
and then Receive via Infrared in list view.
— 38 —
7. ADUSTMENT
There are two kinds of adjustments using Operation Check diagnostic program concerning E-125 as
well as EM-500.
Refer to OPERATION CHECK in this manual concerning how to enter into Operation Check Mode.
The following two adjustments can not be performed without entering into Operation Check Mode.
For more information, refer to OPERATION CHECK in this manual.
It is recommended to perform these adjustments whenever replacing Main PC Board Assembly.
■ Display Quality adjustment (TFT VCOM voltage adjustment)
When flickers and vertical stripes appear in the screen display, try to perform this adjustment according
to the following procedure.
Refer to OPERATION CHECK and DISASSEMBLY PROCEDURE in this manual.
1. Set AC adapter, the rechargeable battery and CF card installed the diagnostic program to the unit
after disassembling the unit as shown below.
2. Enter into Operation Check Mode referring to OPERATION CHECK in this manual.
Doing so, Main Menu for Operation Check will appear.
3. Tapping 8 COLOR BAR, the following Color Bar check Menu display appears.
** COLOR BAR **
1 Contrast
2 Scroll
3 GRAY
4. Tapping 3 GRAY, all gray display appears on the screen.
If abnormal displays (flicker, vertical stripes and so on) are detected, change VCOM voltage
rotating above variable resistor VR300 using a ceramic screwdriver (minus/ 1.8 mm width) so that
these abnormal displays disappear.
VR300 can be supplied as one of the spare parts. Refer to PARTS LIST in this manual.
Refer to page 70 in the Service Manual for E-115 concerning VCOM.
VCOM: Common electrode voltage for TFT LCD pixel.
— 39 —
NOTE:
Although this adjustment is described in
OPERATION CHECK in this manual, It is
recommended to adjust after assembling the
dummy lower case assembly added a hole
(approximately 10 mm in diameter) as shown
to the right.
■ Adjustment to correct (compensate) AD converter error voltage
This is the adjustment to correct or compensate AD converter error voltage/ digital data.
Generally speaking, the differential and linear errors exist in the output digital data and voltage which
are passed AD/ DA converter.
When calibration for touch panel, battery voltage detection and so on are not correctly performed,try to
perform this adjustment.
Important
This adjustment for the main PC Board Assembly for the spare parts has not been performed in the
factory.
Therefore, be sure to perform this adjustment whenever you replace the main PC Board Assembly.
It is recommended to prepare two DC voltage stabilizers for Main and sub (back up) power supplies.
Perform this adjustment according to the following procedure.
1. While supplying powers as shown to the right,
display Main Menu for the operation check.
* Remove AC Adapter.
* Slide the battery cover switch to LOCK
position.
2. Make the voltage power supply added to the
main battery terminal 4.2V ± 0.05V.
Then, make the voltage power supply added to
the back up battery terminal 2.7V ± 0.05V.
If turning off the unit power, stop to supply
power for the back up battery at first, then for the
main battery. After performing Initial Setup,
display Main Menu for the operation check again.
— 40 —
3. Tapping 9 voltage Write, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
Voltage Write-> Contacts Key
Escape
-> ON Key
4. Pressing Contacts button, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
AD Value Read!
0x8...
<Min Level Write>
Voltage Write-> Contacts Key
Escape
-> ON Key
If the unit can not read the voltage 4.2V correctly, “No Good. Please retry!!” message will appear.
Note that the unit can not be progressed in the next stage whenever this message appears.
5. Make the voltage power supply added to the main battery terminal 3.7V ± 0.05V.
Then, press Contacts button again.
Doing so, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
AD Value Read!
0x8...
<Min Level Write>
AD Value Read!
0x8...
<SUB Level Write>
Voltage Write-> Contacts Key
Escape
-> ON Key
6. Pressing Contacts button again, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
AD Value Read!
0x8...
<Min Level Write>
AD Value Read!
0x8...
<SUB Level Write>
AD Value Read!
0x8...
Write Data Value
Max=0x...
Sub=0x...
Min=0x...
-----------→ Test END
Push Action Key
7. Pressing Action Control button, the following display appears along with Main Menu display.
AD Code=OOOOO
CPROG Rev.1.01 for JX-650
If missed, the following # displays appear instead of O.
AD Code=# # # # #
CPROG Rev.1.01 for JX-650
— 41 —
If this display appears, be sure to try to perform these adjustments again.
After turning off the unit power, stop to add the powers to the unit from DC voltage stabilizers After
setting the rechargeable battery, back up battery and AC Adapter to the unit again, perform Initial Setup,
then display Main Menu.
— 42 —
8. OPERATION CHECK
8-1. Preparation
1. E-125 (Prepare two units to perform IrDA communication check.)
2. Compact Flash Memory Card
3. Rechargeable battery pack CGP-E/104A (Refer to PARTS LIST.)
4. AC adapter (AD-C59200U), or both AC adapter (AD-C59200G) and AC power cord
(CBL-K799-AC-EU etc.) (Refer to PARTS LIST.)
5. Cradle (Refer to PARTS LIST.)
6. PC installed ActiveSync 3.1
7. Diagnostic program files for E-125 : diag.exe and diagboot.exe
(This file name "diag.exe" is the same as ones for E-100/ E-105/ E-115/ EM-500 etc. Take care not
to confuse.)
9. Ordinary stereo earphone (16Ω)
10. Two DC Power Supply Stabilizers
NOTES:
* Be sure to make back-up copies of all data in the unit before repair using BACKUP/ RESTORE
function in ActiveSync 3.1 software because FULL RESET must be performed to finish or abort this
operation check.
Diagnostic program file will be saved in D-RAM assembled onto the main PC board.
Therefore, performing FULL RESET after this check, this program should be deleted.
These program files (diag.exe/ diagboot.exe/ CASIO_JXdiag.exe) will be supplied along with the
Service Manual for E-125.
* The unit may be locked during the installation, this check or the other operation.
If this lock occur, try to perform RESET operation.
8-2. How to install the diagnostic program
There are two ways to install the diagnostic program.
8-2-1. Installation in CF Card
Using CF card installed the diagnostic program, OPERATION CHECK can be performed without PC and
the cradle after installation.
To make this CF card installed the diagnostic program, at first, it is necessary to install the diagnostic
program to CF card according to the following
procedure.
1. Insert a CF card into Card slot of the unit.
Before inserting CF card, be sure to slide CARD
LOCK switch to FREE position.
2. Connect a cradle and PC installed ActiveSync
3.1.
3. Set the unit to this cradle. And then, open
ActiveSync 3.1.
4. Selecting File, then Connection Settings..., the
dialog box shown to the right appears.
It is recommended that you enter "V" marks in
the four squires in the right dialog box to be able
to use USB, RS-232C COM port etc on PC.
5. After doing so, perform "Get Connected..."
procedure. "Get Connected..." procedure may
automatically start.
6. You had better choose "No" for Set Up a
Partnership.
— 43 —
7. After that, this connection procedure will be
completed.
8. After this procedure is completed, the
display shown to the right appears.
9. After clicking Explore icon in the right
dialog box, click My Pocket PC icon.
10. Doing so, Storage Card holder icon will
appears.
"Storage Card" holder indicates CF card. If
CF card is not inserted into the slot, this
holder will not appear.
11. After clicking this icon, make a new holder
named jx650diag.
12. Make a new holder named
casioconfidential in jx650diag holder.
Perform these spellings precisely.
Otherwise, the installation of the diagnostic program can not be performed.
13. Enter diag.exe file in this casioconfidential holder.
Total directory is as follows;
Storage Card>jx650diag>casioconfidential>diag.exe
14. Doing so, the installation of the diagnostic
program to CF card and D-RAM in the unit
starts automatically.
15. While performing this installation, the
display shown to the right will appear.
16. Completing this installation, the display
shown to the right will appear.
* Once the diagnostic program is installed in
CF card and D-RAM in the unit, this
program is not deleted even if RESET
operation is performed.
17. After making diag holder in Storage Card
holder, enter diagboot.exe file into this diag
holder. Total directory is as follows;
Storage Card>diag>diagboot.exe
Note: diagboot.exe file is needed to make the diagnostic program development more easier.
This file may be applicable to all units adopted CF card in future.
18. Performing the following operation with the unit, confirm that the diagnostic program has been
installed in CF card according to the following procedure.
Tapping Start, Programs, File Explore, My documents, My Device, Storage Card, jx650diag,
and then casioconfidential holder using a stylus, diag icon will appear.
If diag icon appears, the diagnostic program is installed in CF card.
After tapping casioconfidential, tap Storage Card holder.
Tapping Storage Card, confirm that there is a diagboot icon in Storage Card holder.
Tapping this diag icon, Main Menu for this Operation Check display appears.
It is recommended to boot Operation Check using above operations.
— 44 —
8-2-2. Direct Installation in Only D-RAM in the unit without CF card
Using the following procedure, you can install the diagnostic program in D-RAM in the unit without CF
card.
1. Perform 2~9 in the procedure of 8-2-1.
2. Clicking Windows holder, open this holder.
3. Enter CASIO_JXdiag.exe and diagboot.exe files into this holder.
4. Doing so, the installation of the diagnostic program to D-RAM in the unit starts automatically.
* Once the diagnostic program is installed in D-RAM in the unit, this program is not deleted even if
RESET operation is performed.
5. Performing the following operation with the unit, confirm that the diagnostic program has been
installed in D-RAM in the unit.
Tapping Start, Programs, File Explore, My documents, My Device, and then Windows holder
using a stylus, CASIO_JXdiag and diagboot icons will appear in Windows holder.
If CASIO_JXdiag and diagboot icons appears, the diagnostic program is installed in D-RAM.
Tapping this CASIO_JXdiag icon, Main Menu for this Operation Check display appears.
Operation Check can be booted using above operation also.
8-3. How to delete the diagnostic program
If necessary, delete the diagnostic program in CF card and D-RAM in the unit using the following procedure.
8-3-1. How to delete the diagnostic program in CF card
1. After connecting the unit set CF card and PC using ActiveSync 3.1, be sure to delete diag.exe file
in casioconfidential holder.
Never delete jx650diag or casioconfidential holder.
Refer to 8-2-1 concerning above connection for detail.
2. Performing the following operation with the unit, confirm that the diagnostic program has been
deleted in CF card according to the following procedure.
Tapping Start, Programs, File Explore, My documents, My Device, Storage Card, jx650diag,
and then casioconfidential using a stylus, diag icon will disappear.
If diag icon disappears, the diagnostic program in CF card is deleted.
8-3-2. How to delete the diagnostic program in D-RAM in the unit
There are two ways to delete the diagnostic program in D-RAM.
1. After connecting the unit and PC using ActiveSync 3.1, delete CASIO_JXdiag.exe and diagboot
files in Windows holder.
Refer to 8-2-1 concerning above connection for detail.
2. Perform FULL RESET for the unit.
To perform FULL RESET, press RESET button while holding down Power button, then operate the
unit according to the messages on the screen.
* Performing the following operation with the unit, confirm that the diagnostic program has been
deleted in D-RAM in the unit.
Tapping Start, Programs, File Explore, My documents, My Device, and then Windows using a
stylus, CASIO_JXdiag and diagboot icons will disappear in Windows holder.
If CASIO_JXdiag and diagboot icons disappears, the diagnostic program in D-RAM is deleted.
— 45 —
8-4. Operation Check
8-4-1. How to enter into Operation Check Mode
It is recommended to perform FULL RESET with the unit to delete the data saved in D-RAM before this
check.
To enter into this check Mode, perform the operation described in item 18 of 8-2-1 or item 7 of 8-2-2 after
installation of diagnostic program.
Or, after the installation of diagnostic program using
the operation described in 8-2-2, press Contacts
button over 3 seconds while holding down Power
button until below Operation Check Main Menu
appears.
After performing one of the operations described
above, the following Main Menu display for
Operation Check appears on the screen.
** Main Menu **
1 DISPLAY
2 TOUCH PANEL
3 MEMORY
4 SERIAL
5 POWER CONTROL
6 AUDIO
7 Others
8 COLOR BAR
9 VOLTAGE Write
Note: Generally, diagnostic program revision No. may be
changed without prior notice in future due to mass
production convenience.
AD Code = #####
CPROG Rev. 1.01 for Jx-650
In case of E-125 unit, It is recommended not to pull out CF card installed the diagnostic program during
this check if using this CF card.
8-4-2. Operation Check
If the unit is locked during this check, enter into this check mode again after perform RESET or
FULL RESET operation.
8-4-2-1. Display Check
1. Tapping above 1 DISPLAY on the screen using a stylus, the red screen appears.
2. Tapping the screen, the green screen appears.
3. Tapping the screen again, the blue screen appears.
4. Tapping the screen again, the white frame display appears.
5. Tapping the screen again, the black frame display appears.
6. Tapping the screen again, no display appears.
7. Tapping the screen again, Main Menu display appears.
— 46 —
8-4-2-2. Touch Panel Check
1. Tapping above 2 TOUCH PANEL on the screen using a stylus, the following Touch Panel Check
Menu appears.
** Touch Panel **
1 Case
2 Points
3 Cross
2. Tapping 1 Case, "Case ---→ OK" display appears.
Pressing Action Control button, display Touch Panel Check Menu again.
Generally speaking, pressing Action Control button, prior Menu or Display can be recovered
during Operation Check.
3. Tapping 2 Points, four cross marks appears near four corners in the screen.
If succeeded to tap the center of the cross mark, its cross mark will disappear.
Tap the centers of these cross marks until all cross marks disappear.
After that, "Touch Panel ---→ OK" display appears.
4. Pressing Action Control button twice, Main Menu display appears.
* If performing 2 Points check, it is unnecessary to perform 3 Cross check.
8-4-2-3. Memory Check
1. Tapping 3 MEMORY, the following Memory Check Menu display appears.
** MEMORY **
1 ROM CHECK SUM(32MByte)
1' ROM CHECK SUM(16MByte)
2 ROM BUS SUM(32MByte)
2' ROM BUS SUM(16MByte)
3 ROM TYPE
4 RAM TEST
5 RAM LOOP
6 RAM R/W TEST
2. Tapping 1 ROM CHECK SUM(32MByte), the following display appears.
** ROM CHECK SUM **
base addr. sum value
SUM 1 (be000000) = xxxx
SUM 2 (be000002) = xxxx
ROM CHECK SUM ... end
Above hexadecimal digits (numbers) will be modified without prior notice in response to the
modifications for OS etc..
Pressing Action Control button, Memory Check Menu display appears again.
3. Tapping 3 ROM TYPE, the following display appears.
** ROM TYPE **
Flash ROM
ROM Type CHECK ... end
Mask ROM may appear instead of above Flash ROM.
Pressing Action Control button, Memory Check Menu display appears again.
— 47 —
4. Tapping 4 RAM TEST, the following display appears.
The other displays may appear.
** RAM CHECK **
- RAM CHK OK Pressing Action Control button, Memory Check Menu display appears again.
5. Tapping 6 RAM R/W TEST, the following display appears.
** RAM CHECK **
- RAM DATA WRITE Write ... end
ActionKey PUSH!
6. Pressing Action Control button according to above message, the following display appears.
** RAM CHECK **
- RAM DATA WRITE Write ... end
ActionKey PUSH!
-- RAM DATA READ --- RAM CHK OK -Pressing Action Control button twice, Main Menu display appears again.
8-4-2-4. Serial ports Check (Communication Check)
Try to communicate with PC using ActiveSync 3.1 after connecting the unit to PC using the cradle
concerning USB and RS232C checks.
Because, special jigs are needed to perform USB checks by this diagnostic program.
1. Tapping 4 SERIAL, the following Serial port Check Menu display appears.
** Serial **
1 Loop Back
<RS232C Ck>
2 Send / Receive <RS232C Ck>
3 Interactive
<IrDA Ck>
4 Send / Receive <IrDA Ck>
5 Loop Back2
6 USB Check
2. Prepare another unit to perform IrDA communication check.
Display Serial port Check Menu with another unit as well as the checking unit.
3. Tapping 4 Send / Receive <IrDA Ck> with both units, the following displays appear.
4. Tap 2 Receive data (MAX Baudrate) with another unit, then tap 1 Send data (MAX Baudrate)
with the checking unit. Doing so, the following displays appear.
In case of the checking unit;
<Send mode>
In case of another unit;
<Receive mode>
HHHHHHHHHHHHHHHHHH
HHHHHHHHHH....................
The letter "H" will continue to appear one after another.
5. To stop this data communication, press Action Control buttons with both units.
6. Exchanging the checking unit for another unit, perform operations of above 3~5.
Press Action Control buttons few times with both units to display Main Menu.
Turn off another unit power after performing FULL RESET.
— 48 —
8-4-2-5. Audio Check
1. Tapping 6 AUDIO, the following Audio check Menu appears.
** Audio **
1 0.5kHz
2 1kHz
3 2kHz
4 LR-Channel
5 Record
2. Tapping 1 0.5kHz, 0.5kHz sound is emitted.
3. Tapping 2 1kHz after pressing Action Control button, 1 kHz sound is emitted.
4. Tapping 3 2kHz after pressing Action Control button, 2 kHz sound is emitted.
Press Action Control button again.
5. After setting a stereo earphone to the unit, tap 4 LR-Channel.
Doing so, the following sound can be heard from its earphone with stereo.
"Right channel" from the right
"Left channel" from the left
Press Action Control button again.
8-4-2-6. Others Check
1. Tapping 7 Others, the following Others check Menu display appears.
** Others **
1 Switch
2 Keyboard RAMDOM
3 Disp Loop
4 BackLight
2. Tapping 1 Switch, the following display appears and Red light is flickered from the right LED.
VDET1B
OFF
VDET2
OFF
VDET3
OFF
VDETS
OFF
VDETCF
OFF
AC Adapter
USED
Cover
CLOSED
Charge
ON
Audio Jack
OFF
3. Removing the back up battery, VDETS will become ON.
Set its back up batter to the unit again.
4. Removing AC Adapter, AC Adapter will become NOT USED.
Connect AC Adapter to the unit again.
5. Connect a ordinary earphone to the unit.
Doing so, Audio Jack will become ON.
Remove this earphone.
6. Sliding the Battery Cover Switch to MAIN position, Cover will become OPEN.
7. Pressing Action Control button, Others check Menu display appears again.
8. Tapping 2 Keyboard RANDOM, the following display appears.
** Keyboard Random **
Pressing any button except power button, Key name corresponded to the pressed button appears
on the screen. Pressing Power button finally, Others check Menu display appears again.
— 49 —
9. Tapping 4 BackLight, for example, the following display appears.
439
Another number may appear.
10. While holding down the downward key in the cursor button, display on the screen becomes dimmer,
then lighter suddenly.
Pressing Action Control button twice, Main Menu appear.
8-4-2-7. Color Bar Check (including a display adjustment)
Refer to ADJUSTMENT in this manual concerning below VCOM adjustment.
1. Tapping 8 COLOR BAR, the following Color Bar check Menu display appears.
** COLOR BAR **
1 Contrast
2 Scroll
3 GRAY
2. Tapping 1 Contrast, the following color bar display appears.
RED
GREEN
BLUE
BLACK
WHITE
Pressing Action Control button, Color Bar check Menu display appears again.
Even if tapping 2 Scroll, this unnecessary check can not be performed because this check
becomes unnecessary.
3. Tapping 3 GRAY, all gray display appears on the screen.
If abnormal displays (flicker, and so on) are
detected, change VCOM voltage rotating the
variable resistor VR300. Refer to page 70 in the
Service Manual for E-115 concerning VCOM.
VCOM: Common electrode voltage for TFT LCD
pixel.
Refer to PARTS LIST concerning VR300.
To perform this adjustment, it is recommended to
adjust after assembling the dummy lower case to
which a round hole is added as shown below.
Refer to the item 24 of PARTS LIST and
EXPLODED VIEW concerning the lower case.
Pressing Action Control button twice, Main Menu
display appears.
— 50 —
8-4-2-8. Setting (Adjusting) DC voltage to AD converter
Refer to ADJUSTMENT in this manual concerning this voltage adjustment.
The following operation are not only for Check, but also for setting (adjusting) for DC voltage to AD
converter in CPU.
When calibration for touch panel, battery voltage detection and so on are not correctly performed, try to
check and perform these settings (adjustments).
It is recommended to prepare two DC voltage stabilizers for Main and sub (back up) power supplies.
Important
These settings (adjustments) for the main PC
Board Assembly has not been performed in the factory.
Therefore, be sure to perform this setting (adjustment)
whenever you replace the main PC Board Assembly.
1. While supplying powers as shown to the right,
display Main Menu for the operation check.
* Remove AC Adapter.
* Slide the battery cover switch to LOCK position.
2. Make the voltage power supply added to the main
battery terminal 4.2V ± 0.05V.
Then, make the voltage power supply added to the
back up battery terminal 2.7V ± 0.05V.
If turning off the unit power, stop to supply power
for the back up battery at first, then for the main
battery. After performing Initial Setup, display
Main Menu for the operation check again.
3. Tapping 9 voltage Write, the following display
appears.
*** <AD Revision Value Write> ***
<Max Level Write>
Voltage Write-> Contacts Key
Escape
-> ON Key
4. Pressing Contacts button, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
AD Value Read!
0x8...
<Min Level Write>
Voltage Write-> Contacts Key
Escape
-> ON Key
If the unit can not read the voltage 4.2V correctly, "No Good. Please retry!!" message will appear.
Note that the unit can not be progressed in the next stage whenever this message appears.
— 51 —
5. Make the voltage power supply added to the main battery terminal 3.7V ( 0.05V.
Then, press Contacts button again.
Doing so, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
AD Value Read!
0x8...
<Min Level Write>
AD Value Read!
0x8...
<SUB Level Write>
Voltage Write-> Contacts Key
Escape
-> ON Key
6. Pressing Contacts button again, the following display appears.
*** <AD Revision Value Write> ***
<Max Level Write>
AD Value Read!
0x8...
<Min Level Write>
AD Value Read!
0x8...
<SUB Level Write>
AD Value Read!
0x8...
Write Data Value
Max=0x...
Sub=0x...
Min=0x...
---------→ Test END
Push Action Key
7. Pressing Action Control button, the following display appears along with Main Menu display.
AD Code=OOOOO
CPROG Rev.1.01 for JX-650
If missed, the following # displays appear instead of O.
AD Code=# # # # #
CPROG Rev.1.01 for JX-650
If this display appears, be sure to try to perform these settings (adjustments) again.
After turning off the unit power, stop to add the powers to the unit from DC voltage stabilizers
After set the rechargeable battery, back up battery and AC Adapter to the unit again, perform
Initial Setup, then display Main Menu.
----- END ----
After removing CF card saved the diagnostic program, perform FULL RESET.
— 52 —
9. TROUBLE SHOOTING
Before assuming malfunction and contacting expert when experiencing
operational problems, be sure to check the following information as well as the
troubleshooting section of the Pocket PC User’s Guide first.
Nothing happens when the [Power] button is pressed.
Possible Cause
Recommended Action
Main battery is weak.
Charge the battery pack.
Internal malfunction
Reset the unit.
If resetting the unit does not correct the
problem, perform a full reset (memory
initialize).*
Operation is disabled when the AC adapter is connected.
Possible Cause
Recommended Action
Main battery is weak.
Charge the battery pack.
The unit is not mounted on the cradle
correctly.
Mount the unit on the cradle correctly.
Replacing the main battery caused malfunction.
Possible Cause
Recommended Action
Main battery is not loaded correctly.
Remove and then reload the main
battery.
• Make sure the positive (+) and negative
(–) poles are oriented correctly.
The battery replacement procedure was
not followed correctly.
Perform a full reset (memory initialize).*
• If the above action does not solve the
problem, remove the main battery
and contact with experts.
Rechargeable battery pack life is very short after each charge.
Possible Cause
Recommended Action
Battery pack is damaged or has reached
the end of its service life.
Purchase a new battery pack.
— 53 —
The low backup battery message continues to appear even after replacement of the
backup battery.
Possible Cause
Recommended Action
The backup battery is upside down.
Remove the backup battery, turn it
over, and reload it.
The backup battery was loaded before the
main battery.
Remove the backup battery, and reload it.
Power was left on while the battery
pack was replaced.
Turn power off and then back on again.
Nothing happens when the touch screen is touched.
Possible Cause
Recommended Action
The touch screen is out of calibration.
Recalibrating the touch screen.
Static electricity or some other problem has
caused the touch screen to malfunction.
Reset the unit.
The touch screen is damaged.
Contact your original dealer or an
expert.
The screen is locked up.
Possible Cause
Recommended Action
Internal malfunction
Reset the unit.
If resetting the unit does not correct the
problem, perform a full reset (memory
initialize).*
A message about a data error is on the screen.
Possible Cause
Recommended Action
Internal malfunction
Follow the instructions that appear on
the screen.
* Perform the procedure on the page 24 when the full reset (memory initialize) does not correct the
problem.
— 54 —
10. CIRCUIT BLOCK DIAGRAM
Timer clock
32.768kHz
OSB
System clock for CPU
18.432MHz
PLL
150MHz
KEYS
CORE of CPU
Instruction/ Cache Mem.
Action/ Voice etc.
IC5
IrDA Module
CPU
IC2
(BGA)
VR4122
OSB
Bus Control Unit
Alarm LED
(RED)
LED IF
(Key PCB)
Rechargeable
Battery
IC200
Power IC
* Power supply
* Voltage regulator
* Voltage detection
* Charge control
General Purpose
Interface
AC Adapter
AD-C59200
Charge LED
(To Cradle)
DC/AC
Inverter
V5LCD
(Amber/ Green)
RESET
System clock
45.158MHz
DATA BUS
POWER
ON/OFF
ADDRESS BUS
DRAM x 2
DRAM1/ DRAM2
IC 1
GATE ARRAY (ASIC): KUJIRA
*KUJIRA is a Japanese nickname for this Gate Array, and
can not be replaced as well as above CPU because of BGA
32 Mbytes
(16 Mbytesx2)
* For Communication and LCD drive/control etc.
ROM x 2
MROM1/MROM2
16 Mbytes
(8 Mbytesx2)
Fast IrDA clock
48MHz
Backup
Battery
Back light
Voltage
CF/MODEM
Card
(US and
Canada only)
LCD (TFT) Module
240 x 320 dots
MIC
IC303
VCOM
Battery power detection
IC300
* Battery Power detection
* Touch Panel IF
* HP/ SP drive
Touch Panel
Headphone
IC306
USB
CRADLE
PC
Mobile
Phone
Speaker
MODEM
(US & Canada
only)
To Analog Telephone line
(From AC adapter)
— 55 —
11. WIRING DIAGRAM
LCD Module
Touch Panel
CF Card
FFC
Flat Cable
MIC
SP
Headphone
AC Adapter Jack
Rechargeable
Battery
Lithium Battery
for Memory Backup
Ferrite Core
USB Cable
AC Adapter
Jack
— 56 —
AC Adapter
12. SCHEMATIC DIAGRAMS
12-1. Main block (1/3)
IrDA Module
RESET
Gate Array
CPU
— 57 —
12-1. Main block (2/3)
Rechargeable
Battery
— 58 —
12-1. Main block (3/3)
— 59 —
12-2. ROM block
— 60 —
12-3. Key block
— 61 —
12-4 USB Cradle
— 62 —
13. PCB VIEW
Main PC Board (1/2)
— 63 —
Main PC Board (2/2)
— 64 —
Key PC Board
— 65 —
14. DISASSEMBLY PROCEDURE
Refer to GENERAL GUIDE, PARTS LIST and EXPLODED VIEW in this manual also.
1. Remove a stylus, a lithium battery for
memory backup, a rechargeable
battery and CF card slot cover as shown
to the right photograph.
Refer to GENERAL GUIDE, RESET
OPERATION and BATTERY
REPACEMENT in this manual
concerning how to remove.
2. Remove a black battery and screws
as shown to the right.
3. Open the unit after unhooking using a opener
as shown to the right.
It is recommended to unhook while pulling
the upper case outside
— 66 —
4. Open the unit as shown to the right.
5. Remove the lower case assembly after
disconnecting wires from Main PC Board
assembly using a soldering iron as shown to the
right photograph.
Red wire will be connected to the terminal pad
marked plus (+) before this disconnection
as shown to the right
illustration.
+
Black
Red
6. Open the upper case and inner case assemblies
as shown to the right.
7. Disconnect FPC from CN2 connector assembled
onto Key PC Board assembly.
Then disconnect the socket from the connector
assembled onto Main PC Board assembly.
Doing so, both the upper case and inner case
assemblies can be separated as shown to the
right.
— 67 —
8. Open the inner case assembly as shown to the
right.
9. Remove Main PC Board assembly after
disconnecting FPC assembled onto LCD Module
from CN4 connector as shown to the right.
10. Remove the touch panel assembly after
removing screws.
11. Disconnect the socket from CN1 connector
assembled onto the inverter PC Board assembly
as shown to the right.
— 68 —
12. Peel TFT LCD Module from the inner case
assembly as shown to the right.
At this time, take care that this module is
damaged because this module is strongly
attached to the inner case.
Don't use any chemical substances to peel it.
Otherwise, TFT LCD is damaged by these
substances.
— 69 —
14. PARTS PRICE LIST
14-1.PCB ASSY, COMPONENTS and OTHERS
N
N
N
N
N
N
N
N
N
N
Item
Code No.
Parts Name
PCB ASSY/MAIN (C141078*1)
1
6566 6260 SPRING/BATTERY
2
6566 3840 TAPE/SHIELD
3
6566 4660 TAPE
4
6566 4720 TAPE/INSULATION
5
6566 2100 SPACER
SW1
3412 1946 SWITCH
SW2,SW3,S 2370 1392 SWITCH
W4
SW6
3412 2084 SWITCH
SW200
3412 2107 SWITCH
CN3
3502 2568 CONNECTOR
CN4
3502 2460 CONNECTOR
CN5
2259 2791 CONNECTOR
CN205
2254 0553 CONNECTOR
CN306
3502 2647 JACK
CN307
3502 2553 CONNECTOR
CN308
3502 2644 CONNECTOR
CN309
3502 2296 CONNECTOR
CN310
1003 4737 CONNECTOR
Q1
2259 2695 TRANSISTOR
Q201,Q215, 2254 0490 FET
Q222,Q226
Q207
7911 3038 TRANSISTOR/DIGITAL
Q300,Q301 2250 1605 TRANSISTOR
Q304,Q306 2259 2513 TRANSISTOR/DIGITAL
Q305
2259 2765 TRANSISTOR/DIGITAL
D2
2370 1390 LED
D201,D211 2360 3061 DIODE/SCHOTTKY
D203,D204,
2895 3130 DIODE/SCHOTTKY
D205,D208
D207
7911 2114 DIODE
D209,D210 7911 3787 DIODE
D212,D215 2390 0623 DIODE/SCHOTTKY
X1
1002 8054 OSCILLATOR/CRYTAL
X2
1002 8055 OSCILLATOR/CRYTAL
X3
1002 8045 OSCILLATOR/CRYTAL
X4
2590 2783 OSCILLATOR/CRYTAL
VR300
3122 3717 RESISTER/CHIP SEMI-FIXED
IC203
2105 6328 IC/MOS
IC204
2105 3773 IC/MOS
IC205
2105 5824 IC/L-MOS
INNER CASE ASSY
6
1003 6262 PCB ASSY/MAIN
7
1000 3145 PANEL/TOUCH
8
1002 6477 LCD MODULE
9
6566 3690 CASE/INNER
10
6566 3700 PLATE
Specification
Applicable
Q Price Code R
C342892-1
C443236-1
C443536-1
C443588-1
C442708-1
EVQ7QH03W
EVQPSC02K
Common
Common
Common
Common
Common
Common
Common
3
1
1
1
2
1
3
AA
AH
AA
AA
AA
AB
AB
C
C
C
C
C
C
C
SLLB12-A-B-B
ABC1112P
52746-0690
54104-4590
53916-0808
HEC3650-012010
HSJ1494-01-010
55350-5026
52271-0490
BM04B-SRSS-TB
54393-4592
DTA114YKAT146
2SK1827-TE85L
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
1
1
1
1
1
1
1
1
1
1
1
1
4
AN
AB
AB
AH
AL
AG
AF
AU
AA
AC
AK
AA
AA
C
C
C
C
C
C
C
C
C
C
C
C
C
DTC114YUAT106
2SC4081T106
DTA114EUAT106
DTC114EUAT106
SML-210LTT86M
RB491DT146
RB051L-40TE25
Common
Common
Common
Common
Common
Common
Common
1
2
2
1
1
2
4
AA
AA
AA
AA
AA
AA
AC
C
C
C
C
C
C
C
RB751V-40TE-17
M1FS4-4063
SB07-03C-TB
FCX-03-45.1584M2
FCX-03-48.000M2
MC146-32.768K-7/20
FCX-03-18.432M2
MVR32HXBRN222
XC62FP5002MR
TC7SH08FU-TE85L
TC7SH32FU-TE85L
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
1
2
2
1
1
1
1
1
1
1
1
AA
AA
AC
AM
AM
AK
AL
AA
AD
AB
AB
C
C
C
C
C
C
C
C
C
C
C
C141078*1 TK
KTB97B002A
COM38T3104DPQ
C140810-1
C342313-1
Common
Common
Common
Common
Common
1
1
1
1
1
EM
BW
EC
AM
AE
B
B
B
X
C
- 70 -
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Item
Code No.
Parts Name
11
6566 3720 CABLE/JOINT
12
1000 1738 TAPE
13
6566 1880 TAPE
14
1003 4750 TAPE
15
1003 4749 PCB ASSY/FPC
16
1003 0002 PCB ASSY/INVERTER
17
6566 3860 SPRING/EARTH
18
6566 4410 TAPE
19
6566 4420 TAPE
20
6566 4670 TAPE
21
6566 4710 TAPE/INSULATION
22
6566 5230 TAPE/INSULATION
23
6566 3740 TAPE
81
1003 7160 TAPE
LOWER CASE ASSY
24
1003 4759 CASE/LOWER
25
6566 3640 HOLDER
26
6566 3650 KNOB
27
6566 3660 KNOB
28
6566 3670 KEY
29
6566 3680 HOLDER
82
1004 1541 TAPE
PCB ASSY/BACKUP BATTERY
30
6566 3760 PCB
31
6562 1331 SPRING/BATTERY
32
6511 0770 SPRING/BATTERY
33
6410 4560 PLATE/INSULATION
PCB ASSY/KEY(C343550*1)
CN2
1003 4737 CONNECTIOR
CN3
2259 2752 CONNECTIOR
PCB ASSY/AUDIO(C241821*1)
34
3335 6646 MIC
35
6562 1620 HOLDER
36
1003 4770 CABLE SUB ASSY
37
3335 6578 SPEAKER
UPPER CASE ASSY
39
1003 6263 PCB ASSY/KEY
40
6566 1650 NET/SPEAKER
41
6566 1622 HOLDER/SPEAKER
42
1003 4754 CASE/UPPER
43
1003 4752 KEY
44
6566 3560 COVER
45
1003 4751 KEY
46
1003 4756 KEY
47
1003 4757 KEY
Specification
C443132-1
C443824-1
C442716-1
C444550-1
C343487-1
INV-J598-S
C443425-1
C443559-1
C443563-1
C443583-1
C443575-1
C443621-1
C443153-1
C444634-1
Applicable
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Q Price Code
1
AD
4
AA
1
AA
2
AA
1
AE
1
BR
1
AC
2
AA
1
AA
1
AB
1
AA
1
AA
4
AA
2
AA
R
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C140809A-6
C342321-1
C342320-1
C342319-1
C342326-1
C342370-1
C444712-1
Common
Common
Common
Common
Common
Common
Common
1
1
1
1
1
1
2
BB
AC
AB
AB
AC
AC
AA
X
C
C
C
C
C
C
C342334-1
C442225A-1
C311380-1
C413459-1
Common
Common
Common
Common
1
1
1
1
AB
AA
AA
AA
X
C
C
C
54393-4592
TCX3110-010100
Common
Common
1
1
AK
AR
C
C
WM-64KY102
C442143-1
C444502*1
20D2
Common
Common
Common
Common
1
1
1
1
AM
AA
AE
AV
C
C
C
C
C343550*1 TK
C442768-1
C442694B-1
C140808D-5
C343537-1
C342318-1
C342323A-4
C444543-1
C444544-1
Common
Common
Common
Common
Common
Common
Common
Common
Common
1
1
1
1
1
2
1
1
1
BV
AA
AA
BQ
AI
AB
AI
AC
AC
B
C
C
X
C
C
C
C
C
- 71 -
N
N
N
N
N
N
N
N
N
Item
Code No.
Parts Name
48
1003 4758 KEY
49
6566 3610 RUBBER/KEY
50
6566 3620 RUBBER/KEY
51
6566 2310 TAPE
83
1003 7245 TAPE
COMPONENTS
52
1003 4729 PEN SUB ASSY
53
1003 6265 PCB ASSY/ROM
54
1003 4732 COVER/BATTERY
55
1003 4731 COVER
56
1001 5853 COVER
57
1003 4730 COVER
58
6566 3520 FILTER/IRDA
59
1003 4733 PLATE
60
6566 3310 BADGE/CASIO
61
6566 4430 SHEET/BATTERY
62
6566 0270 LABEL/CAUTION
OTHERS
63
6566 3220 BOARD/CRADLE
64
3815 0828 CASE/SOFT
65
1002 9287 SOFTWARE/CD-ROM(MS)
66
1001 7213 ADAPTER/AC
*AC Input voltage of this AC Adapter (item 66) is 120V.
67
1001 5583 ADAPTER/AC
Specification
C444545-1
C342324-1
C342325-1
C442920-1
C444613-1
Applicable
Common
Common
Common
Common
Common
Q Price Code
1
AC
1
AA
1
AA
1
AA
AA
1
R
C
C
C
C
C
C342013A*4
C343480*2 TK
C342327-4
C342317-4
C342316-3
C342315-4
C342328-1
C342432-14
C443357-1
C443498-1
C341668-2
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
Common
1
1
1
1
1
1
1
1
1
1
1
AK
CX
AL
AG
AB
AG
AB
AA
AE
AB
AA
C
B
C
C
C
C
C
C
C
C
C
C241325-1
SCJ530AA02
CDJ670AA01A
AD-C59200U
Common
Common
Common
U, C
1
1
1
1
AM
AS
BM
CB
C
C
C
C
DA, DB, DC,
DD, E, B
1
CH
C
Common
DA, DB, DC,
DD, E
DA
DD, B
DC
1
1
CS
AR
C
C
1
1
1
AO
BJ
AS
C
C
C
U, C
DA, DB, DC,
DD
E, B
1
1
AL
AM
C
C
1
AM
C
1
AM
C
AD-C59200G
*AC Input voltage arange of this AC Adapter (item 67) is 100~240V.
* Refer to EXPLODED VIEW concerning these AC Adapters (item 66 and 67).
68
3815 0820 BATTERY/ACCUMULATOR
CGP-E/104A
69
1000 6300 CORD/AC
CBL-K799-AC-EU
70
1000 6299 CORD/AC
CBL-K799-AC-JU
71
1002 9319 CORD/AC
SP23-17688
72
1002 9316 CORD/AC
INQ957
*Refer to to the lower table concerning these AC Power Cord (item69~72).
N
73
1003 4936 SOFTWARE/CD-ROM(CASIO) CDJ650EA02A
N
74
1003 4937 SOFTWARE/CD-ROM(CASIO) CDJ650EA03A
N
75
1003 4938 SOFTWARE/CD-ROM(CASIO) CDJ650EA04A
Note 1: CD-ROMs (item 73, 74 and 75) are the English Version CD-ROMs.
Note2: CD-ROM for music software and AOL CD-ROM will be not supplied as spare parts
because of the direct supply from Microsoft Corp. etc. as well as E-115.
And these CD-ROMs are shipped to U.S.A. and Canada.
N
76
1004 2333 SOFTWARE/CD-ROM
CDJ650EA07A
U, C
Note3: This CD-ROM (item 76) for Media Player Upgrade will be not enclosed from
the middle of mass production (Maybe, serial mass production unit's No. 30001~).
Parts prices will be informed separately by Parts Price List.
- 72 -
Applicable
U
C
E
B
DA
DB
DC
DD
Shipment
U.S.A.
Canada
Europe
U.K.
Others (AC 100~120V)
Others (AC 200~240V)
Australia
Hong Kong
AC Power Cord
Item
Code No.
69
1000 6300
70
1000 6299
71
1002 9319
72
1002 9316
Specification
CBL-K799-AC-EU
CBL-K799-AC-JU
SP23-17688
INQ957
Note
German Type (Round 2 Pin Plug)
USA and Canada Type (Rectangular 2 Pin Plug)
UK Type
Australian Type
- 73 -
14-2. CRADLE
N
N
N
N
Item
101
102
103
Code No.
Parts Name
1003 6981 CRADLE
1003 6267 PCB ASSY/CRADLE
1003 4769 CABLE
Specification
C241388*8 TK
C241826*1 TK
UCJ650AA01A
Applicable
Common
Common
Common
Parts prices will be informed separately by Parts Price List.
Notes:N-New parts
Q-Quantity used per unit
R-Rank
R- A:Essential
B:Stock recommended
C:Others
X:No stock recommended
- 74 -
Q Price Code
1
CH
1
BN
1
AR
R
C
C
C
16. EXPLODED VIEW
16-1. PCB ASSY and COMPONENTS (1/6)
— 75 —
16-1. PCB ASSY and COMPONENTS (2/6)
— 76 —
16-1. PCB ASSY and COPONENTS (3/6)
— 77 —
16-1. PCB ASSY and COPONENTS (4/6)
— 78 —
16-1. PCB ASSY and COPONENTS (5/6)
(PCB ASSY/AUDIO)
— 79 —
16-1. PCB ASSY and COPONENTS (6/6)
— 80 —
16-2. OTHERS (1/3)
— 81 —
16-2. OTHERS (2/3)
— 82 —
16-2. OTHERS (3/3)
— 83 —
16-3. CRADLE
— 84 —
CASIO TECHNO CO.,LTD.
Overseas Service Division
Nishi-Shinjuku Kimuraya Bldg. 1F
5-25, Nishi-Shinjuku 7-Chome
Shinjuku-ku, Tokyo 160-0023, Japan