Yamaha DTX RS500 Owner`s manual

DTX700K
Digital Musical Instruments Division
©2011 Yamaha Corporation
WW60760 110PO***.*01C0
Assembly Manual
EN
This pamphlet describes the standard procedure for DTX700K assembly.
After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.
1
2
Assemble the RS500 Rack System.
For details, refer to the assembly manual that came with the rack system.
Check the contents of each package.
Package 1: DTP700C
 PCY135
Cymbal Pad (x2)
Standard Assembly Example
 RHH135
Real Hi-hat Pad (x1)
Package 2: DTP700P
 Stand base for the
RHH135 (x1)
 XP70
Tom Pad (x3)
 HS650A
Hi-hat Stand (x1)
 XP80
Snare Pad (x1)
 KP65
Kick Pad (x1)
IMPORTANT
PCY135
(Cymbal Pad)
• For assembly, you will require four individual packages – an RS500
Rack System, a DTP700C Pad Set, a DTP700P Pad Set, and a
DTX700 Drum Trigger Module.
PCY135
(Cymbal Pad)
• This pamphlet describes how to attach the pads and drum trigger
module to the RS500 Rack System. Before carrying out the procedures described below, ensure that you have correctly assembled
the rack system as described in its assembly manual.
XP70
(Tom Pad)
RHH135
(Real Hi-hat Pad)
DTX700 Drum
Trigger Module
XP70
(Tom Pad)
 Hi-hat clutch for the
RHH135 (x1)
 Stoppers for the
PCY135 (x2)
NOTICE
Before starting assembly, lay a drum mat (sold separately) on the floor.
Alternatively, before setting up the HS650A Hi-hat Stand and KP65
Kick Pad, you can place the packages' cardboard boxes on the floor to
protect it from damage.
 Clamp bolts (x4)
 Tuning key (x1)
 Cable bands (x10)
 XP70 and XP80 Owner’s Manual (x1)
 KP65 Owner’s Manual (x1)
Package 3: DTX700
 Cable band for the
RHH135 (x1)
 DTX700 Drum Trigger
Module (x1)
 Felts for the
PCY135 (x2)
 9-channel snake cable
(x1)
HS650A
(Hi-hat Stand)
 Module stand (x1)
 AC power adaptor*
(x1)
 Module stand
fastening screws (x4)
RS500
(Rack System)
KP65
(Kick Pad)
* May not be included depending on your particular
area. Please check with
your Yamaha dealer.
 DTX700 Owner’s Manual (x1)
 DTX700 Data List (x1)
 DVD (containing software) (x1)
 PCY100, PCY135, and PCY155 Owner’s Manual (x1)
 RHH135 Owner’s Manual (x1)
 Assembly Manual (this pamphlet)
XP80
(Snare Pad)
3
PRECAUTIONS
Mount the pads and the drum trigger module on the rack system.
As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.
Mounting snare and tom pads
Before using, please read this assembly manual, and use this product in a safe and proper manner.
2. Mount the snare pad on the rack’s clamp rod. As
* Please keep this manual in a safe place for future reference.
* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.
XP70
WARNING
If this symbol is ignored and the equipment is used improperly, fatal
injury to persons or serious damage could occur.
CAUTION
If this symbol is ignored and the equipment is used improperly,
there is a danger or injury to persons handling the equipment, and
material damage could occur.
• Do not let small children assemble or set up this product by themselves, or they may be injured.
Always assemble this product with adult supervision.
• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends
may result in injury.
• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your
fingers.
shown below, ensure that the rod section is fully inserted into the pad’s mounting hole, and then fully
tighten the clamp bolt.
XP80
Snare pad
Clamp rod
 Mounting the tom pad
1.
As with the snare pad, attach the clamp bolt to each
of the three tom pads and provisionally tighten (by 5
or 6 turns).
2. Mount the three tom pads on the rack’s clamp rods.
As shown below, ensure that the rod section is fully
inserted into each pad’s mounting hole, and then
fully tighten the clamp bolt.
Rod
section
Tom pad
Insert
• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends
may result in injury.
• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting
in injury.
• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened
firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may
result in the rack overturning or parts dropping, causing injury.
• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums
may drop, causing injury.
• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on
steps may result in the product being unstable and subject to overturning.
• When setting up the product, please pay close attention to the handling and setting of cables.
Carelessly placed cables may cause the user and others to trip and fall.
• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
NOTICE
• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,
never place any heavy or sharp objects on the cable. Applying excessive force to the cable may
result in damage to the cable, such as the wires being severed, etc.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,
close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).
Doing so may result in deformation, discoloration, damage or deterioration.
• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or
deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has
been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to
let the water and detergent come into contact with the cushions used in the product; doing so may
result in deterioration.
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
Rod
section
Clamp rod
Clamp bolt
Insert
3. If necessary, use clamp bolts A to E to adjust the
 Mounting the snare pad
1.
Attach the clamp bolt to the snare pad and provisionally tighten (by 5 or 6 turns).
Clamp bolt (to be tightened in the direction
shown)
Snare pad (rear side)
height and angle of the snare pad. When doing so,
be sure to adjust one bolt at a time (i.e., loosen a
bolt, adjust the pad, and then retighten before loosening another).
Clamp bolt B
Clamp bolt
3. If necessary, use clamp bolts A to D to adjust the
height and angle of any of the pads. When doing so,
be sure to adjust one bolt at a time (i.e., loosen a
bolt, adjust the pad, and then retighten before loosening another).
Clamp bolt D
Clamp bolt E
Clamp bolt B
Clamp bolt A
Clamp bolt A
Clamp bolt C
Clamp bolt C
Clamp bolt D
Continued on other side
Mounting the drum trigger module and cymbal pads
Assembling the kick pad
 Mounting the cymbal pads
PCY135
PCY135
1.
Using a tuning key, loosen the stopper’s key bolt.
5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt
cover, tighten the stopper’s key bolt using a tuning
key.
If a drum mat (sold separately) is not available, lay a sheet of cardboard on the
floor to protect it from scratching.
Spring washer
2. Remove the wing bolts, spring washers, and washers from the kick pad body, and
Key bolt
Washer
Wing bolt
line up each set nearby in the order in which it was removed.
3. Join the base section to the body as shown right, and then secure it in place by
Stopper
Drum trigger
module
1.
assembling the wing bolts, spring washers, and washers removed in the previous
step from the base side.
Bolt cover
Body
Body
Full contact
Stopper
Tuning key
Base
Cymbal holder
2. Remove the wing nut, the two felt pads, and the bolt
cover from the cymbal holder.
6. Place one of the felt pads removed in Step 2 on the
cymbal holder.
Wing nut
Bolt cover
Mount the pad unit on the cymbal stand. Lower the
pad unit into place with the cymbal holder’s shaft
passing through the central hole of the cup section.
When mounted, the stopper’s pin should rest inside
the pad unit’s smaller hole.
Cymbal holder
* If you were to play a cymbal pad without the stopper’s pin positioned inside the smaller hole, the
pad could rotate, causing the cable to be pulled
out. It is very important, therefore, to ensure that
the stopper is secured as described in Step 5
above.
Felt pads
 Mounting the drum trigger module
1.
7.
Attach the module stand (provided) to the underside
of the drum trigger module using the module stand
fastening screws.
Module stand
fastening screws
4
Position the hi-hat stand and kick pad as desired, referring to the standard assembly example on the other side.
5
Connect the pads to the drum trigger module.
1.
8. Assemble the felt pad that came with your pad unit.
Module stand
3. Place the stopper on the cymbal holder.
Drum trigger module
(back side)
* If the key bolt was not sufficiently loosened in
Step 1 above, it may not be possible to pass the
stopper over the cymbal holder’s shaft. In such a
case, loosen the key bolt as much as possible
without removing it.
Front of
module
* The second felt pad removed from the cymbal
holder in Step 2 above is not required for assembly of your pad unit.
Insert the 9-channel snake cable’s straight plugs into the drum trigger module’s
trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]).
• If you are using the standard setup, the stickers on each of the snake cable’s
plugs will indicate the name of the corresponding pad.
9
Pad unit
Felt pad that came
with pad unit
Smaller
hole
[9-channel
snake cable]
Pad unit
Stopper
Straight
plugs
Drum trigger
module
+
module stand
Felt pad
Cymbal holder
Insert
Bolt cover
6
Assembling the hi-hat stand
5. As shown on the right, loosen the wing bolt (b in the
figure) to remove the hi-hat clutch.
* This hi-hat clutch is not used within the standard
assembly example shown in this pamphlet. Instead, use the hi-hat clutch that came with your
RHH135.
2. Loosen the hi-hat stand’s wing bolt (a in the following figure).
3. Extend the tripod legs to stabilize the stand.
6. Pull out the hi-hat shaft
Retighten the wing bolt loosened in Step 2.
4. Insert the radius rod into the frame hole as shown
below.
1.
Hi-hat
clutch
Felt
washer
Screw the hi-hat shaft
pipe
.
from the upper pipe
into the nut on the lower
No
6
Connection
5
4
3
2
1
Straight plug names
(as shown on stickers)
DTX700 jack names
SNARE
TOM1
TOM2
TOM3
RIDE
CRASH
HI HAT
HH CON
KICK
1: qSNARE
2: wTOM1
3: eTOM2
4: rTOM3
5: tRIDE
6: yCRASH1
7: iHI-HAT
8: HI-HAT CONTROL
9: oKICK/!0
3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out.
NOTICE
Excessive bending can damage the pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when
wrapped around the clips.
Connect the drum trigger module to a power supply.
Insert the power adaptor’s DC plug into the
connector. Hook the power
adaptor’s cord around the cord clip to secure it in place.
[Drum trigger module’s rear panel]
b
.
7.
7
HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE
Cymbal holder
* When assembling the bolt cover, turn until it no
longer rotates.
8
L-shaped
plugs
Clamp bolt
If a drum mat (sold separately) is not available, lay
a sheet of cardboard on the floor to protect it from
scratching.
[Locations of pad jacks]
Pin
Stopper
Holder clamp
2. Plug the 9-channel snake cable’s L-shaped plugs into the correct pads.
[Drum trigger module’s rear panel]
Stopper’s pin
tighten the clamp bolt to secure in position.
1.
As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.
cymbal holder.
Wing nut
Bolt cover
Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard
boxes on the floor under the hi-hat stand and kick pad to protect it from damage.
9. Tighten the wing nut to secure the pad unit to the
4. Replace the bolt cover.
2. Place the module stand inside the holder clamp and
NOTICE
Support
plate
Support
plate
connector
Cord clip
c
8. Insert the upper pipe
into the hi-hat shaft
from above, and then tighten the wing bolt (c in the
figure) with the support plate positioned at the middle area of the hi-hat shaft
.
Wing bolt a
2. Use the cable bands to bind the cables to the rack as shown on the right. (
9. Remove the felt washer located above the support
3. Plug the AC power adaptor into an AC wall socket.
plate. It is not used within the standard assembly example shown in this pamphlet.
Radius rod
Radius rod
)
10. Set up the RHH135 Real Hi-hat Pad.
* Refer to refer to the Setting Up section of the
owner’s manual that came with your RHH135.
This completes the assembly procedure.
* For information about tuning the power on/off, checking the actual sound, and other subsequent steps,
refer to the Setting Up section of the owner’s manual that came with your drum trigger module.