Sharp FO-70 Service manual

UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SERVICE MANUAL
No. 00ZUX8TH//SME
FACSIMILE
UX-8
UX-40
GQ-5
MODEL FO-50
Illustration: UX-8
This service manual is omitted because it is partly common to UX-60TH/FO-70TH of the service manual of the
previous issue. Those common parts are to refer to the service manual of UX-60TH/FO-70TH (00ZUX60TH/SME).
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications ............................................
[2] Operation panel .........................................
[3] Transmittable documents ..........................
[4] Installation .................................................
[5] Quick reference guide ...............................
1-1
1-2
1-3
1-4
1-9
CHAPTER 2. ADJUSTMENTS
[1] Adjustments .............................................. 2-1
[2] Diagnostics and service soft switch .......... 2-2
[3] Troubleshooting ...................................... 2-18
[4] Error code table ....................................... 2-19
CHAPTER 3. MECHANISM BLOCKS
[1] General description ................................... 3-1
[2] Disassembly and assembly
procedures ....................................... 3-3
CHAPTER 4. DIAGRAMS
[1] Block diagram ............................................4-1
[2] Wiring diagram .......................................... 4-2
[3] Point-to-point diagram ............................... 4-3
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Refer to the service manual of UX-60TH.
[2] Refer to the service manual of UX-60TH.
[3] Refer to the service manual of UX-60TH.
[4] Refer to the service manual of UX-60TH.
[5] Refer to the service manual of UX-60TH.
CHAPTER 6. CIRCUIT SCHEMATICS AND
PARTS LAYOUT
[1] Control PWB circuit ................................... 6-1
[2] TEL/LIU PWB circuit .................................. 6-9
[3] Power supply PWB circuit ...................... 6-13
[4] Operation panel PWB circuit ................... 6-15
CHAPTER 7. OPERATION FLOWCHART
[1] Refer to the service manual of UX-60TH.
[2] Refer to the service manual of UX-60TH.
CHAPTER 8. OTHERS
[1] Refer to the service manual of UX-60TH.
[2] Refer to the service manual of UX-60TH.
PARTS GUIDE
Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
CAUTION FOR BATTERY REPLACEMENT
(Danish)
ADVARSEL !
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the equipment manufacturer.
Discard used batteries according to manufacturer’s
instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type recommandé par le constructeur.
Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfare vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications
Automatic dialing:
Fax paper:
Rapid Key Dialing: 5 numbers
(Note for UX-8/GQ-5: Rapid Key Dialing
is not available)
Speed Dialing: 35 numbers
(Note for UX-8/GQ-5: 10 number)
Initial starter roll (included with machine):
10 m
Recommended replacement roll:
FO-20PRw, 30m, 12.7mm core
Paper cutting method:
Tear off by hand
Modem speed:
9600 bps with automatic fallback to lower
speeds
Transmission time* :
Approx. 15 seconds
Resolution:
Horizontal: 8 dots/mm
Vertical:
Standard: 3.85 lines/mm
Fine/Halftone: 7.7 lines/mm
Super fine: 15.4 lines/mm
Automatic document feeder: 5 pages max. (20 lb paper)
(UX-8/GQ-5: This function is not available)
Halftone (grayscale):
64 levels
Display:
16-digit LCD display
Compression scheme:
MR, MH, Sharp (H2)
Applicable telephone line:
Public switched telephone network
Compatibility:
ITU-T (CCITT) G3 mode
Input document size:
Automatic feeding:
Width: 148 to 216 mm
Length: 140 to 297 mm
Manual feeding:
Width: 148 to 216 mm
Length: 140 to 600 mm
Effective scanning width:
210 mm max.
Effective printing width:
210 mm max.
Contrast control:
Automatic/Dark selectable
Reception modes:
Fax, Tel, Tel/Fax, A.M.
Copy function:
Yes
Telephone function:
Yes (cannot be used if power fails)
Power requirements:
220-240 V AC, 50/60 Hz
Operating temperature:
5 - 35°C
Humidity:
Maximum: 85 % RH
Power consumption:
Standby: 2.3 W
Maximum: 115 W
Dimensions:
Width: 304 mm
Depth: 236 mm
Height: 122 mm
Weight:
Approx. 2.6 kg
* Based on ITU-T (CCITT) Test Chart #1 at standard resolution in Sharp
special mode, excluding time for protocol signals (i.e., ITU-T phase C
time only).
Note: The facsimile machine is Year 2000 compliant.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct
improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some
deviation from these values in individual units.
1–1
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[2] Operation panel
1 2
3 4
RECEPTION
MODE FUNCTION
TEL FAX
TEL
6 7
5
RESOLUTION
FAX
DOWN
VOLUME
UP
A.M.
TEL/FAX A.M.
ABC
1
DEF
ABC
SPEED DIAL
A
GHI
JKL
C
B
D
E/
VOLUME
01
02
STOP
REDIAL
03
04
PQRS
05
06
07
08
FUNCTION
PQRS
TUV
WXYZ
COPY/
HELP
HOLD/SEARCH
START
2
4
POLL
MNO
RESOLUTION/
RECEPTION MODE
3
STOP
MNO
5
6
8
REDIAL
COPY/HELP
HOLD/
SEARCH
WXYZ
TUV
7
SPEED
DIAL
DEF
JKL
GHI
2
9
0 START
SPEAKER
SPEAKER
09
8
9
1. Rapid Dial keys
10 11
When a document is in the feeder, press this key to make
a copy of a document. At any other time, press this key to
print out the Help List, a quick reference guide to the
opeation of your fax machine.
2. Display
11. RESOLUTION/RECEPTION MODE key
When a document is in the feeder, press this key to adjust
the resolution for faxing or copying. At any other time,
press this key to select the reception mode (an arrow in the
display will point to the currently selected reception mode).
3. FUNCTION key
Press this key to select various special functions.
4. VOLUME keys
Press this keys to adjust the volume of the speaker when
the SPEAKER key has been pressed, the volume of the
ringer at all other times.
12. SPEAKER key
Press this key to listen the line and fax tones through the
speaker when faxing a document.
Note: This is not a speakerphone. You must pick up the
handset to talk with the other party.
5. Number keys
Use these keys to dial numbers, and enter numbers and
letters when storing auto-dial numbers.
6. SPEED DIAL key
13. HOLD/SEARCH key
Press this key to search for an auto-dial number, or, during a
phone conversation, press this key to put the other party on
hold.
Press this key to dial a fax or voice number using an
abbreviated 2-digit Speed Dial number.
7. REDIAL key
Press this key to automatically redial the last number
dialed.
12 13 14
10. COPY/HELP key
Press one of these keys to dial a fax number automatically.
Note for UX-8/GQ-5: Rapid Key Dialing is not available.
This displays messages and prompts during operation and
programming.
10/POLL
14. Panel release
Grasp this finger hold and pull toward you to open the
operation panel.
8. START key
Press this key to begin transmission when using Speed
Dialing, Direct Keypad Dialing, or Normal Dialing.
9. STOP key
Press this key to cancel operation before it is completed.
1–2
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[3] Transmittable documents
5. Automatic Document Feeder Capacity
1. Document Sizes
Number of pages that can be placed into the feeder at anytime is as
follows:
Normal size
width
length
Normal size: max. ADF 5 sheets
148 – 216 mm
140 – 297 mm
Special size: single sheet only (manual feed)
NOTES:
(Max.)
(Max.)
A4 size
(Min.)
•
600mm
297mm
216mm
[Normal size]
When you need to send or copy more pages than the feeder
limit, place additional pages in feeder when last page in
feeder is being scanned.
Place additional pages carefully and gently in feeder.
If force is used, double-feeding or a document jam may
result.
6. Readable Width & Length
140mm
148mm
•
The readable width and length of a document are slightly smaller than
the actual document size.
216mm
[Special size]
Note that characters or graphics outside the effective document scanning range will not be read.
Use document carrier sheet for smaller documents.
•
* With special sizes, only one sheet can be fed into the machine at a
time. Insert next page into feeder as current page is being scanned.
Readable width
210mm, max.
2. Paper Thickness & Weight
4x6 series
(788mm x 1091mm x
1000mm sheets)
Minimum
Feeder capacity
Paper weight
Maximum
Square
meter series
Minimum
Maximum
52g/m2
80g/m2
5 sheets, max.
45kg
69.2kg
Paper thickness (ref.) 0.06mm
0.09mm
0.06mm
0.09mm
Paper size
148mm x 140mm ~
A4 (210mm x 297mm), Letter (216mm x 279mm)
Readable width
3. Document Types
•
Normal paper
•
Documents handwritten in pencil (No. 2 lead or softer), fountain
pen, ball-point pen, or felt-tipped pen can be transmitted.
This is the length of the document sent minus 5mm from the top and
bottom edges.
Readable length
Documents of normal contrast duplicated by a copying machine
can also be transmitted.
•
Diazo copy (blue print)
•
Carbon copy
5mm
Diazo copy documents of a normal contrast may be transmitted.
Readable length
A carbon copy may be transmitted if its contrast is normal.
5mm
4. Cautions on Transmitting Documents
•
Documents written in yellow, greenish yellow, or light blue ink cannot
be transmitted.
•
Ink, glue, and correcting fluid on documents must be dry before
the documents can be transmitted.
•
All clips, staples and pins must be removed from documents before transmission.
•
Patched (taped) documents should be copied first on a copier and
then the copies used for transmission.
•
All documents should be fanned before insertion into the feeder to
prevent possible double feeds.
1–3
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
7. Use of Document Carrier Sheet
TELEPHONE JACK
A document carrier sheet must be used for the following documents.
• Those with tears.
A standard telephone jack must be located near the machine.
This is the telephone jack commonly used in most homes and offices.
•
•
•
Those smaller than size 148mm (W) x 140mm (L).
Carbon-backed documents
Make print straight
across paper
E.G.
Place the document
carrier in the document
feeder with the clear film
side down
Plugging the fax machine into a jack which is not an jack may result in
damage to the machine or your telephone system. If you do not know
what kind of jack you have, or need to have one installed, contact the
telephone company.
2. Assembly and connections
1 Plug the power cord into a 220-240 V, 50/60 Hz, grounded AC outlet.
Direction of insertion
•
Caution: Do not plug the power cord into any other kind of outlet.
This will damage the machine and is not covered under the warranty.
•
The machine does not have a power on/off switch, so the power is
turned on and off by simply plugging in or unplugging the power
cord.
NOTE: To transmit a carbon-backed document, insert a white sheet of
paper between the carbon back of the document and the document carrier.
• Those containing an easily separable writing substance (e.g., tracing paper written on with a soft, heavy lead pencil).
NOTES:
•
When using the document carrier, carefully read the instructions written on the back.
•
If the document carrier is dirty, clean it with a soft, moist
cloth, and then dry it before using for transmission.
•
Do not place more than one document in the carrier at a
time.
2 Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset cord are identical, so they will go into
either jack.
[4] Installation
1. Site selection
Take the following points into consideration when selecting a site for this
model.
ENVIRONMENT
•
•
The machine must be installed on a level surface.
Keep the machine away from air conditioners, heaters, direct sunlight, and dust.
•
Provide easy access to the front, back, and sides of the machine. In
particular, keep the area in front of the machine clear, or the original
document may jam as it comes out after scanning.
•
•
The temperature should be between 5° and 35°C.
Make sure the handset cord
goes into the jack marked
with a handset symbol on the
side of the machine!
Use the handset to make ordinary
phone calls, or to transmit and receive
faxes manually.
The humidity should be between 30% and 85% (without condensation).
3 Attach the original document support as shown below.
ELECTRICITY
220-240 V, 50/60 Hz, grounded (3-prong) AC outlet is required.
Caution!
•
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
•
If your area experiences a high incidence of lightning or power surges,
we recommend that you install a surge protector for the power and
telephone lines. Surge protectors can be purchased at most telephone
specialty stores.
If the machine is moved from a cold to a warm place...
Condensation may from on the reading glass if machine is moved from
a cold to a warm place, this will prevent proper scanning of documents
for transmission. Turn on the power and wait approximately 2 hours before using machine.
1–4
4 Insert one end of the line cord into the jack on the back of the ma-
2 Flip up the front paper guide.
chine marked TEL. LINE. Insert the other end into a standard singleline wall telephone jack.
TE
SEL.
T
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Note: Do not peel off or
bend this strip of film.
TE
LI L.
NE
Note: The fax machine is set for touch-tone dialing. If you are on a
pulse dial (rotary) line, you must set the fax machine for pulse dialing.
Press the keys on the operation panel as follows:
3 Remove the packing paper.
1. Press these keys:
FUNCTION
The display will show:
4
DIAL MODE
2. Press 1 to select tone (touch-tone)
dialing, or 2 to select pulse (rotary)
dialing.
1
3. Press the STOP key to return to the date
and time display.
PULSE
TONE
or
2
4 Flip down the front paper guide and then close the operation panel.
STOP
3. Removing the packing paper
1 Grasp the finger hold and open the operation panel.
1–5
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
6 Insert the leading edge of the paper into the slot as shown. Continue
4. Loading the fax paper (FO-20PRw)
•
Your fax machine prints incoming faxes on a special kind of paper
called fax paper.
•
The fax machine’s print head creates text and images by applying
heat to the fax paper.
to push the paper through the slot until it comes out the opening in
the front of the machine.
1 Grasp the finger hold as shown and pull up to open the operation
panel.
7 Make sure the paper comes out straight, and then flip down the paper guide.
2 Flip up the front paper guide.
3 If you are loading A4 size paper, place the paper roll shims on each
side of the paper compartment.
• The ribbed side of the shims should face in (toward each other).
8 Close the operation panel, making sure it clicks into place.
• A short length of the paper will feed out. Grasp the paper by the
edge and pull upward to tear it off.
4 Unwrap the roll of fax paper and insert the paper shaft.
5 Place the roll of fax paper in the compartment, making sure the ends
Click!
of the paper shaft fit into the notches on each side of the compartment.
♦ Important: The roll must be placed so the leading edge of the
paper unrolls as shown. (The paper is only coated on one side for
printing. If the roll is placed backwards, the paper will come out
blank after printing.)
YES
NO!
1–6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
4 Flip down the green levers on each side of the white roller.
5. Clearing a jammed document
If the original document doesn’t feed properly during transmission or
copying, or DOCUMENT JAMMED appears in the display, first try pressing the START key. If the document doesn’t feed out, open the operation
panel and remove it.
Important:
Do not try to remove a document without first releasing it as explained
below.
This may damage the feeder mechanism.
1 Grasp the finger hold and pull up to open the operation panel.
5 Close the operation panel, making sure it clicks into place.
• Press down on both front corners of the panel to make sure it
clicks into place.
2 Flip up the green levers on each side of the white roller.
3 Remove the document.
1–7
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
4 Cut off the wrinkled part of the paper.
6. Clearing jammed paper
If the fax paper jams, PAPER JAMMED will appear in the display.
Follow the steps below to clear the jam.
Grasp the finger hold and pull up to open the operation panel.
1
5 Reload the paper.
• Jammed paper is often caused by improper loading. Be sure to
carefully follow the instructions for paper loading given in Loading
the Fax Paper.
2 Flip up the front paper guide.
3 Remove the paper roll.
1–8
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SENDING FAXES
[5] Quick reference guide
ENTERING YOUR NAME AND NUMBER
1. Press:
Place your document (up to 5 pages)
face down in the document feeder.
(UX-8/GQ-5: Only one page can be
loaded at a time.)
FUNCTION
3
Display shows: OWN NUMBER SET
START
2. Press:
3. Enter your fax number (max. of 20 digits) by pressing the number keys.
•
To insert a space between digits, press the # key.
•
If you make a mistake, press the SPEED DIAL key to backspace and clear the
mistake.
4. Press:
Normal Dialing
SPEAKER
1. Lift the handset or press
START
2. Dial the fax number.
5. Enter your name by pressing the appropriate number keys as shown below.
• To enter two letters in succession that require the same key, press the SPEAKER
key after entering the first letter.
3. Wait for the reception tone (if a person answers, ask them to press their Start
key).
SPACE =
J=
T=
A=
K=
U=
Rapid Key Dialing
Press the appropriate Rapid Key. Transmission will begin automatically.
(Note for UX-8/GQ-5: Rapid Key Dialing is not available.)
Speed Dialing
B=
C=
D=
L=
V=
M=
W=
N=
X=
O=
Y=
P=
Z=
START
4. Press:
1. Press:
SPEED
DIAL
2. Enter 2-digit Speed Dial number.
E=
3. Press:
F=
G=
START
Q=
RECEIVING FAXES
H=
R=
I=
S=
Press the RESOLUTION/RECEPTION MODE key until the arrow in the display
points to the desired reception mode (make sure the document feeder is empty).
TEL FAX
•
05 NOV 10:30
To change case, press the REDIAL key.
Press # or to scroll through symbols and special characters.
RESOLUTION/
RECEPTION MODE
TEL/FAX A.M.
TEL FAX
05 NOV 10:30
STOP
6. When finished, press:
TEL/FAX A.M.
TEL FAX
START
05 NOV 10:30
TEL/FAX A.M.
TEL FAX
SETTING THE DATE AND TIME
05 NOV 10:30
TEL/FAX A.M.
1. Press:
FUNCTION
FAX mode: The fax machine automatically answers on four rings and receives the
incoming document.
3
Display shows: DATE & TIME SET
TEL mode:
Beep
START
START
2. Press:
3. Enter two digits for the Day (01 through 31).
4. Enter two digits for the Month (01 through 12).
RECEIVING
5. Enter four digits for the Year (Ex: 1999).
6. Enter two digits for the Hour (01 through 23).
TEL/FAX mode: The fax machine automatically answers on 1 or 2 rings and receives faxes. Voice calls (including manually dialed fax transmissions) are signalled
by a special ringing sound.
7. Enter two digits for the Minute (00 through 59).
8. When finished, press:
STOP
START
A.M. mode: Select this mode when an answering machine is connected to the fax
and the answering machine is turned on.
STORING AND CLEARING AUTO DIAL NUMBERS
1. Press:
FUNCTION
3
Display shows: FAX/TEL # MODE
2. Press 1 to store a number or 2 to clear a number.
3. Enter a 2-digit Speed Dial number (from 01 to 05 for Rapid Key Dialing, or 06 to
40 for Speed Dialing) (If you are clearing a number, go to Step 7.) (UX-8: 01 to
10)
4. Enter the full fax/telephone number.
5. Press:
START
6. Enter the name of the location by pressing number keys (Refer to the letter
entry table in ENTERING YOUR NAME AND NUMBER.)
STOP
7. Press:
START
1–9
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
MEMO
1 – 10
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
3. Settings
CHAPTER 2. ADJUSTMENTS
Dial mode selector
[1] Adjustments
DIAL mode (Soft Switch No. SWB4 DATA No. 2)
(step 1) Select "OPTION SETTING".
General
KEY :
FUNCTION
Since the following adjustments and settings are provided for this model,
make adjustments and/or setup as necessary.
DISPLAY:
OPTION SETTING
4
Adjustments of output voltage (FACTORY ONLY)
KEY:
1. Install the power supply unit in the machine.
Push # until " DAIL MODE " is
indicated because the number of
# s changes by the model.
2. Set the recording paper and document.
3. When the document is loaded, power is supplied to the output lines.
Confirm that outputs are within the limits below.
DISPLAY:
Output voltage settings
DIAL MODE
(step 3) Select, using "1" or "2".
TEL/LIU PWB
KEY:
1
DISPLAY:
TONE SELECTED
KEY:
2
DISPLAY:
PULSE SELECTED
POWER SUPPLY PWB
CNL IUA
CN2
CNPW
CNLIUA
(step 4) End, using the "STOP" key.
KEY:
CONTROL PWB
Voltage limits
4.75V ∼ 5.25V
24.0V ∼ 26.0V
Connector
No.
Pin No.
1
2
3
4
5
6
7
8
CNPW
DG
+5V
MG
MG
+24V
+24V
DG
PSAVE
2. IC protectors replacement
ICPs (IC Protectors) are installed to protect the motor driver circuit.
ICPs protect various ICs and electronic circuits from an overcurrent condition.
The location of ICPs are shown below:
CNLIUA
OR #
(step 2) Select "DIAL MODE".
1. Adjustments
Output
+5V
+24V
PRESS
CNPW
CONTROL PWB
(TOP SIDE)
CNMT
FU100
(1) FU100 (KAB2402) is installed in order to protect IC’s from an overcurrent generated in the motor drive circuit. If FU100 is open, replace it with a new one.
2–1
STOP
Cursor
When initially registering,
the mode shows 1=TONE.
When registering again, the
mode which was registered
formerly is shown.
1=TONE, 2=PULSE
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[2] Diagnostics and service soft switch
1. Operating procedure
(1) Entering the diagnostic mode
Press FUNC → 9 →
→ 8 → # → 7 , and the following display will appear.
(FZK0 ) After 2 sec: DIAG MODE
ROM Ver. FZJ0
FZJ0 (UX-8TH/GQ-5TH)
FZK0 (UX-40TH/FO-50TH)
Then press the START key and country name selected by country select will appear. Select the desired item with the
with the direct key. Enter the mode with the START key.
key or the # key or select
(Diag•specifications)
FUNC
9
8
7
FZJ0
FZK0
DIAG MODE
START
Soft switch mode
START
—
ROM & RAM check
START
A
—
START
Country select
Aging mode
START
—
—
START
Entry data receive
Panel check mode
START
—
—
START
Entry data send
Check pattern
START
B
E
START
Auto feeder mode
Signal send mode
START
C
D
START
All black mode
Memory clear
START
—
—
START
Shading mode
If the diag mode cannot be set, repeat the diag mode operation, performing the following operation.
After the power is turned on and "WAIT A MOMENT" is indicated, press
the STOP key.
STOP
KEY
START
KEY
In relation with the process response (request from Production
Engineering) "WAIT A MOMENT" clock indication may appear depending
on STOP key timing. If the STOP key is held down, "MEMORY CLEAR?"
appears.
"Power ON" +
Memory clear
(Work + Backup)
2. Diagnostic items
ITEM
DIRECT
No.
key
1
—
SOFT SWITCH MODE
Soft switches are displayed and changed. List can be output.
2
A
ROM & RAM CHECK
ROM is sum-checked, and RAM is matched. Result list is output.
3
—
AGING MODE
10 sheets of check patterns are output every 5 minutes per sheet.
4
—
PANEL CKECK MODE
Panel keys are tested. Result list is output.
5
B
CHECK PATTERN
2 sheets of check patterns are output.
6
C
SIGNAL SEND MODE
Various signals of FAX communication are output.
7
—
MEMORY CLEAR
Back-up memory is cleared, and is set at delivery.
8
—
SHADING MODE
Shading compensation is performed in this mode.
9
D
ALL BLACK PRINT
To check the print head, whole dots are printed over the interval of 2 m.
10
E
AUTO FEEDER MODE
Insertion and discharge of document are tested.
11
—
ENTRY DATA SEND
Registered content is sent.
12
—
ENTRY DATA RECEIVE
Registered content is received, and its list is output.
13
—
COUNTRY SELECT
The software parameter that it agreed in each country name is set up.
Contents
Function
2–2
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
3. Diagnostic items description
3. 1. Soft switch mode
3. 6. Signal send mode
This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following
sequence. Moreover, the signal sound is also output to the speaker when
the line monitor of the soft switch is on.
The soft switches are provided so that each operation mode can be set
by using the operation panel.
In this mode, these switches can be checked and set.
[1] No signal (CML signal turned on)
The contents of these switches are backed up.
[2] 9600bps
The available soft switches are SW-A1 to SW-K1.
[3] 7200bps
The content of soft switches is shown in page 2-5 to 2-17.
[4] 4800bps
The contents are set to factory default settings.
[5] 2400bps
[6] 300bps (FLAG)
3. 2. ROM & RAM check
[7] 2100Hz (CED)
ROM executes the sum check, and RAM executes the matching test.
The result will be notified with the number of short sounds of the buzzer
as well as by printing the ROM & RAM check list.
Number of short sounds of buzzer 0 → No error
[8] 1100Hz (CNG)
[9] Pseudo Ring (models with auto TEL/FAX changeover function)
[10] END
1 → ROM error
2 → RAM error (32Kbyte)
3. 7. Memory clear
This mode is used to clear the backup memory and to reset to the factory default settings.
The content of each setting will be cleared.
3. 3. Aging mode
If any document is first present, copying will be executed sheet by sheet.
If no document is present, the check pattern will be printed sheet by
sheet. This operation will be executed at a rate of one sheet per 5minutes, and will be ended at a total of 10 sheets.
Note: Be sure to execute the memory clear mode whenever you change
the country select setting. The default settings of the soft switches
vary according to the destinations. Therefore, if you do not execute
the memory clear after changing the country select setting, some
functions may not work.
3. 4. Panel check mode
This mode is used to check whether each key operates properly or not.
Press the key on the operation panel, and the key will be displayed on
the display. Therefore, press all keys. At this time,finally press the STOP
key.
3. 8. Shading mode
The mode is used for the shooting compensation. For reading, set up
the special original paper.
When the STOP key is pressed, the keys which are not judged as
"pressed" will be printed on the result list.
The shooting compensation memorizes the reference data of white and
black for reading.
• LED part of the contact image sensor (CIS) is kept on during the term
from when "START" of the panel test mode to end with the STOP key.
Moreover, the memorized data is not erased even if memory clear mode
is executed.
3. 5. Check pattern
3. 9. All black print
This mode is used to check the status of print head. Two sheets of check
pattern are printed. The following information of check pattern is printed.
This mode is used to check the state of the printing head and intentionally overheat it. Whole dots are printed over the interval of 2 m. If it is
overheated or the printing sheet is jammed, press STOP key for the end.
1 Vertical stripes (alternate white and black lines) Approx. 35 mm
2 Full black
Approx. 70 mm
3 Full white
Approx. 35 mm
3. 10. Auto feeder mode
In this mode, a document is inserted and discharged to check the auto
feed function.
After this mode is started, set a document, and the document feed will
be automatically tested.
1
3. 11. Entry data send
This mode is used to send the registered data to the other machine and
to make the other machine copy the registered content. Before sending
in this mode, it is necessary to set the other machine at the entry data
receive mode.
2
The contents to be sent are as follows (the machine prints each list after
the transmission has completed):
1. Telephone list data
3
2. Sender (cover sheet) register data
RANK 0 or 1
3. Optional setting content
Note:
There is a selection RANK 0 or 1 depending on resistance value of the
thermal head. RANK 0 or RANK 1 is printed at the tail of check pattern
to identify.
4. Soft switch content
5. Junk fax number list
6. Country setting content
2–3
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
3. 12. Entry data receive
3. 13. Country select
This mode is used to receive the registered data from the other machine
and to make your machine register the received data. Before receiving
in this mode, it is necessary to set the other machine at the entry data
send mode.
1. Telephone list data
This mode is used to set line connecting parameters which correspond
to each destination.
When the country select mode is selected, and then the START key is
pressed, the destination (country name) currently set will be displayed.
By pressing the # or key, selectable destinations (country names) are
displayed. When the destination (country name) you want to choose is
displayed, press the START key. Each parameter will be stored in RAM.
2. Soft switch list
Destinations (Country names) you can select are as follows:
After receiving is completed, the machine prints the following lists:
3. Junk fax number list
COUNTRY NAME
COUNTRY NAME
HONG KONG
(HK)
TAIWAN
(AU)
INDIA
(IN)
THAILAND
(TH)
MALAYSIA
(MY)
GENERAL AREA (GRU)
RUSSIAN
(RA)
GENERAL AREA (GRH)
SINGAPORE
(SG)
AUSTRALIA
(A)
CHINA
(CN)
SOUTH AFRICA (ZA)
Note: Be sure to execute the memory clear mode whenever you
change the country select setting. The default settings of the
soft switches vary according to the destinations. Therefore, if
you do not execute the memory clear after changing the country select setting, some functions may not work.
Do not set a country select setting which is different from that
of the destination of the machine. Some functions will not work
because the function and the PWB specifications are different.
4. How to make soft switch setting
To enter the soft switch mode, press the following key entries in sequence.
Press FUNCTION
DATA No.
9
8
7
START
START
1 2 3 4 5 6 7 8
S F T SW-A1 = 0 0 0 0 0 0 0 0
Press FUNCTION key.
S F T SW-A1 = 1 0 0 0 0 0 0 0
Press
key.
Press
key.
S F T SW-A1 = 1 0 0 0 0 0 0 0
S F T SW-A1 = 1 0 0 0 0 0 0 0
Bit1 - 8 are set.
S F T SW-A1 = 1 0 0 0 0 0 0 0
Press START key during setting.
S F T SW-A2 = 0 0 0 0 0 0 0 0
Soft SW-A2 - SW-K1 are set.
S F T SW-M2 = 0 0 0 0 0 0 0 0
To finish the settings halfway between
SW-A1 and SW-K1, press the STOP
key. In this case, the setting being done
to the SW No. on display will be nullified
while settings done to the preceding
SW Nos. remain in effect.
When the COPY key is pressed, the
contents of soft switches are printed.
The soft switch mode is terminated.
2–4
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
5. Soft switch description
• Soft switch
SW
NO.
SW
l
A1
DATA
NO.
Switch setting and function
ITEM
1
1
2
3
Protect from echo
Forced 4800bps reception
Footer Print
No
Yes
Yes
Yes
No
No
0
0
0
4
Length limitation of copy/send/receive
No limit
Copy/Send:60cm
Receive:1.5m
0
5
CSI transmission
Not transmitted
Transmitted
0
6
DIS receive acknowledgement during G3
transmission
Twice
NSF:Once
DIS:Twice
0
7
Non modulated carrier for V29 transmission
mode
Yes
No
0
8
Reserved
0
Modem speed
SW
l
A2
SW
l
A3
SW
l
A4
V.29
9600bps 7200bps
1
2
3
4
5
6
Reserved
H2 mode
7
8
V.27 ter
4800bps
2400bps
No. 1
No. 2
No. 3
0
0
0
0
0
1
0
0
1
0
0
0
No. 4
1
1
0
0
0
0
0
1
No
Yes
0
0
Communication error treatment in RTN
sending mode(Reception)
No communication error
Communication error
0
CNG transmission
CED tone signal interval
No
1
No. 1
1000ms
1
2
No. 2
1
Yes
750ms
1
500ms
0
75ms
0
0
0
1
0
0
No
0
3
MR Coding
4
5
6
Reserved
Reserved
Reserved
0
0
0
7
8
Reserved
Reserved
0
0
1
2
3
4
5
6
Signal Transmission level
(0~-31 dBm setting by 1dBm step)
Protocol monitor(Error print)
Printed at com. error
Not printed
0
0
1
0
0
0
7
8
Protocol monitor
Line monitor
Yes
Yes
No
No
0
0
Yes
No. =
No. 1
No. 2
Digital equalization setting(Transmitter)
3
4
No. 3
No. 4
Digital equalization setting(Reception
5
6
for Caller ID)
7
8
Error criterion
Anti junk fax check
0
Binary input
16 8 4 2 1
1 2 3 4 5
0 0 1 0 0
Digital equalization setting(Reception)
1
2
SW
l
A5
Initial
setting
0
No. 5
No. 6
10 ~ 20 %
Yes
2–5
7.2km
0km
1
1
0
0
7.2km
0km
1
1
0
0
7.2km
0km
1
1
0
0
5 ~ 10 %
No
1
1
0
0
0
0
0
1
Remarks
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW
NO.
SW
l
A6
DATA
NO.
Switch setting and function
ITEM
1
1
Auto gain control(MODEM)
Enable
Disable
1
2
End Buzzer
Yes
No
1
3
Disconnect the line when DIS is received in
RX mode
No
Yes
1
4
5
Equalizer freeze control(MODEM)
Equalizer freeze control 7200 bps only
On
No
Off
Yes
0
0
6
7
CNG transmission in manual TX mode
Initial compression scheme for sharp fax in
TX mode
Yes
MR mode
No
H2 mode
1
0
8
Modem speed automatic down when RX
level is under -40dBm
Yes
No
0
EOL detect timer
SW
l
A7
SW
l
B1
SW
l
B3
SW
l
B4
No. 1
No. 2
Reserved
0
1
0
4
Reserved
0
5
6
7
Reserved
Reserved
Reserved
0
0
0
8
Reserved
0
1
Hold key
Enable
Disable
1
2
3
Auto dial fax transmission by REDIAL key
Reserved
Yes
No
0
0
4
5
6
7
Recall interval
(0~15.5min setting by 0.5min step)
0
0
0
1
1
0
1
1
Binary input
16 8 4 2 1
4 5 6 7 8
0 1 0 1 0
0
1
0
1
Binary input
8 4 2 1
0
0
0
3
1
2
3
4
1
4
0
0
1
0
0
No. =
Recall times(0~15times setting)
No. =
5
Dial tone detection(Before auto dial)
6
7
8
Reserved
Busy tone detection(After auto dial)
Busy tone detection pulse number
(After auto dial)
Waiting time after dialing
1
2
3
4
5
6
7
Reserved
Reserved
Reserved
Reserved
Reserved
8
1
Reserved
Dial pausing(sec/pause)
2
3
Dial mode
Pulse → Tone change function by
4
Dial pulse make/break ratio(%)
No
No
4 pulses
45 seconds
No. 1
No. 2
Auto dial mode
Remarks
5 seconds 13 seconds 20 seconds 25 seconds
1
2
3
8
1
2
SW
l
B2
Initial
setting
0
key
0
0
Yes
1
Yes
2 pulses
0
1
0
55 seconds 90 seconds 140 seconds
0
1
1
0
1
1
0
0
0
0
0
0
0
4 sec
2 sec
0
0
Tone
Enable
Pulse
Disable
1
1
40/60
33/67
1
Delay timer of before line
0 second 1.5 seconds 3.0 seconds 4.5 seconds
5
6
7
connect
No. 5
No. 6
Reserved
1
0
0
8
Reserved
0
2–6
0
0
0
1
1
0
1
1
OPTION
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Switch setting and function
SW
NO.
DATA
NO.
connect
SW
l
B5
1
2
3
4
5
6
7
8
1
Reserved
DTMF signal transmission level
2
(Low frequency 0~15.5dBm setting
3
4
5
by 0.5dBm step)
6
7
Reserved
Reserved
0
0
8
Reserved
0
1
DTMF signal transmission level
2
(High frequency 0~15.5dBm setting
3
4
5
by 0.5dBm step)
6
7
Reserved
Reserved
8
Reserved
Reading Slice(Binary)
ITEM
Auto dial mode
SW
l
B6
SW
l
B7
1
Delay timer of after line
No. 1
No. 2
No. 3
Fax signal detection after telephone mode dial Yes
Reserved
Reserved
Reserved
1.7s
2.0s
2.5s
3.0s
3.6s
4.0s
5.5s
7.0s
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
No
No. =
16 8 4 2 1
1
0
No. =
SW
l
D1
1
2 3 4 5
1 0 1 0
0
1
0
Binary input
0
0
2 3 4 5
0 1 1 1
1
1
1
0
0
0
Factory
setting
Dark
Light
Daker in
dark
No. 1
No. 2
0
0
Factory
setting
0
1
Dark
1
0
Light
1
1
Daker in
dark
0
0
No. 3
No. 4
0
0
1
0
1
1
0
0
0
0
Reading Slice(Half tone)
3
4
5
6
Line density selection
Reserved
Fine
0
1
Standard
7
8
MTF correction in half tone mode
Reserved
No
Yes
1
Number of rings for auto receive
2
(0~15rings setting)
3
4
5
Automatic swiching manual to auto receive
function
0
0
Binary input
No. =
0
8 4 2 1
0
1 2 3 4
0 0 1 0
1
0
0
Yes
No
CI detect frequency
6
7
8
0
1
1
0
0
0
0
16 8 4 2 1
1
0
Remarks
0
0
Binary input
1
2
SW
l
C1
Initial
setting
0
No. 6
No. 7
Reserved
2–7
As PTT
11.5Hz
13.0Hz
20.0Hz
0
0
0
1
1
0
1
1
0
0
0
OPTION
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW
NO.
SW
l
D2
SW
l
D3
SW
l
D4
DATA
NO.
Switch setting and function
ITEM
1
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
Reserved
0
6
Caller ID function
7
Reserved
0
8
Reserved
0
1
CI off detection timer
2
(0~1550ms setting by 50ms step)
Yes
SW
l
E2
No
0
16 8 4 2 1
3
4
5
1
0
1
2 3 4 5
1 1 1 0
1
1
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
DTMF type Caller ID RX level
2
(0~-44dBm setting by 1dBm step)
No. =
Binary input
1
32 16 8 4 2 1
0
3
4
5
1
1
6
7
Reserved
8
Reserved
2 3 4 5 6
0 1 1 0 0
1
1
0
0
0
0
9sec 15sec 30sec 60sec 90sec 120sec 150sec 180sec
1
2
3
4
automatic switching mode
5
6
CNG detect time at TEL/FAX mode
Post answer tone(TEL/FAX mode)
3 sec
No
5 sec
Yes
0
1
7
8
Type of post answer tone
Pseudo ringer ON/OFF cycle
LA-SI-DO tone
1 sec ON / 4 sec OFF
800Hz single tone
1 sec ON / 2 sec OFF
1
0
1
Pseudo ringer sound output level to the line
2
(0~-15dBm setting by 1dBm step)
Number of CNG signal detection at the
TEL/FAX automatic switching mode
3
4
5
Post answer tone transmission level
6
(0~-15dBm setting by 1dBm step)
No. 1
No. 2
No. 3
Twice
0
0
0
0
0
1
8
1
0
1
0
0
1
1
1
0
0
Once
1
0
1
1
1
0
1
1
1
0
1
0
1
Binary input
1
8 4 2 1
0
1 2 3 4
1 0 1 0
Binary input
1
0
0
No. =
No. =
7
SW
l
E3
0
Binary input
No. =
Pseudo ringing time at the TEL/FAX
SW
l
E1
Initial
setting
0
8 4 2 1
1
5 6 7 8
0
0 1 0 0
No
0
0
2
Disconnect the line when DTMF "#" is received Yes
during TEL/FAX automatic switching mode
Reserved
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
0
2–8
Remarks
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW
NO.
DATA
NO.
Switch setting and function
ITEM
1
DTMF detection time
SW
l
F1
50ms
80ms
100ms
120ms
1
No. 1
0
0
1
1
0
2
3
No. 2
0
1
No
0
1
0
0
4
5
Protection of remote reception(5
)
detection
Remote reception with GE telephone
Remote operation code figure by external
6
TEL (0~9)
7
8
1
CNG detection in STAND-BY mode
Number of CNG detect(AM mode)
Yes
Compatible
SW
l
G2
Not compatible
1
0
8
4
2
1
1
5
0
6
1
7
0
8
1
0
1
1
Yes
1 pulse
No
2 pulses
3 pulses
4 pulses
No. 2
0
0
1
1
0
No. 3
0
1 pulse
1
2 pulses
0
3 pulses
1
4 pulses
1
4
No. 4
0
0
1
1
0
5
6
No. 5
0
1
0
1
Reserved
1
0
7
8
Reserved
Reserved
0
0
1
Quiet detect time
2
(0~15sec setting by 1sec step)
3
SW
l
G1
Binary input
No. =
2
SW
l
F2
Number of CNG detect(STAND-BY mode)
Binary input
0
8
4
2
1
1
3
No. =
1
2
3
4
0
4
5
Quiet detect start timing
0 1 0 0
Binary input
0
0
6
(0~15sec setting by 1sec step)
8
4
2
1
1
5
0
6
1
7
0
8
1
No. =
7
8
1
2
Reserved
Reserved
0
1
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
OGM detect timer
Not work
100ms
200ms
300ms
No. 1
0
0
1
1
0
No. 2
0
30s
1
40s
0
50s
1
60s
1
3
No. 3
0
0
1
1
0
4
5
6
No. 4
0
1
0
1
Reserved
Reserved
1
0
0
7
Reserved
0
8
1
Reserved
Quiet detect level setting
2
(0~-44dBm setting by 1dBm step)
1
2
Section time of quiet detection
SW
l
G3
SW
l
G4
Initial
setting
0
No. =
Binary input
0
1
32 16 8 4 2 1
0
3
4
5
1
1
6
7
Fax switching when A.M. full
8
Reserved
Yes
2 3 4 5 6
0 1 1 0 0
No
OPTION
OPTION
OPTION
OPTION
1
1
0
0
0
0
2–9
Remarks
OPTION
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW
NO.
SW
l
H1
DATA
NO.
ITEM
1
2
3
Busy tone continuous sound detect time
Reserved
Busy tone detect continuation sound detect
4
Reserved
5
Busy tone detect intermittent sound detect
Busy tone detection pulse number
Switch setting and function
1
5 sec
10 sec
No
Yes
0
No
SW
l
I3
SW
l
I4
6 pulses
10 pulses
0
No. 6
0
0
1
1
0
No. 7
0
1
0
1
1
0
Reserved
Busy tone detection ON/OFF time(Lower limit)
150 ms
200 ms
250 ms
350 ms
No. 1
0
0
1
1
0
No. 2
0
650 ms
1
900 ms
0
1500 ms
1
2700 ms
0
3
No. 3
0
0
1
1
0
4
5
6
No. 4
0
1
0
1
Reserved
Reserved
1
0
0
7
8
1
2
3
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
4
Reserved
0
5
6
Reserved
Reserved
0
0
7
8
1
2
3
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
4
Reserved
0
5
6
Reserved
Reserved
0
0
7
8
1
2
Reserved
Reserved
Reserved
Reserved
0
0
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
Busy tone detection ON/OFF time(Upper limit)
SW
l
I2
2 pulses
Yes
4 pulses
7
8
2
SW
l
I1
1
0
0
6
1
SW
l
H2
Initial
setting
0
2 – 10
Remarks
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW
NO.
SW
l
I5
SW
l
I6
SW
l
I7
SW
l
I8
DATA
NO.
Switch setting and function
ITEM
1
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
1
Sender’s phone number setting
2
Reserved
Cannot change
0
3
No. 3
Off
0
4
No. 4
0
1
0
1
0
No. 5
Low
0
Low
0
Middle
1
High
1
1
No. 6
0
0
1
Speaker volume
5
SW
l
J2
Change allowed
Remarks
0
Ringer volume
SW
l
J1
Initial
setting
0
Low
0
Middle
1
High
1
1
OPTION
6
7
Polling key (UX-40/FO-50 only)
8
1
2
Reserved
Reserved
Reserved
0
0
0
3
Reserved
0
4
Reserved
0
5
6
7
8
Reserved
Reserved
Saving energy start timing
Saving energy mode
0
0
0
1
Yes
5 sec
Enable
1
No
OPTION
180 sec
Disable
2 – 11
0
0
OPTION
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW
NO.
DATA
NO.
SW
l
K1
1
Initial
setting
No. 1
Error
0
Send only
0
0
Always
0
2
No. 2
0
0
1
1
0
3
No. 3
0
1
0
1
0
1
SW
l
J3
Switch setting and function
ITEM
Communication results printout
(Transaction report)
12 hour
Month-Day-Year
24 hour
Day-Month-Year
No print
0
0
OPTION
4
5
6
Time format
Date format
Reserved
7
Reserved
8
1
Reserved
Entering diag mode by pressing SPEED key
0
0
0
2
Reserved
0
3
4
Reserved
Reserved
0
0
5
6
Reserved
Reserved
0
0
7
8
Reserved
Reserved
0
0
0
Yes
No
2 – 12
Remarks
0
0
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
• Soft switch function description
SW-A2 No. 6 H2 mode
SW-A1 No. 1 Protect from echo
Used to determine reception of H2 mode (15 sec transmission mode).
When set to OFF, H2 mode reception is inhibited even though the transmitting machine has H2 mode function.
Used to protect from echo in reception.
SW-A2 No. 7 Communication error treatment in RTN sending mode
(Reception)
SW-A1 No. 2 Forced 4800BPS reception
When line conditions warrant that receptions take place at 4800 BPS
repeatedly.
It may improve the success of receptions by setting at 4800BPS.
This improves the receiving document quality and reduces handshake
time due to fallback during training.
Used to determine communication error treatment when RTN is sent by
occurrence of a received image error in G3 reception. When it is set to
"1", communication error is judged as no error.
SW-A2 No. 8 CNG transmission
SW-A1 No. 3 Footer print
When set to "0", this model allows CNG transmission by pressing the
Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case,
CNG transmission can be performed in the auto dial mode.
When set to "1", the date of reception, the sender machine No., and the
page No. are automatically recorded at the end of reception.
SW-A1 No. 4 Length limitation of copy/send/receive
SW-A3 No. 1, No. 2 CED tone signal interval
Used to set the maximum page length.
To avoid possible paper jam, the page length is normally limited to 0.6
meter for copy or transmit, and 1.5 meters for receive.
It is possible to set it to "No limit" to transmit a long document, such as a
computer print form, etc. (In this case, the receiver must also be set to
no limit.)
For international communication, the 2100Hz CED tone may act as an
echo suppression switch, causing a communication problem.
Though SW-A3 No. 1 and No. 2 are normally set to 0, this selfing is used
to change the time between the CED tone signal to eliminate the communication caused by echo.
TX
SW-A1 No. 5 CSI transmission
(CSI TRANSMISSION) is a switch to set whether the machine sends or
does not send the signal (CSI signal) informing its own telephone No. to
the remote fax machine when information is received. When "nonsending"
is set, the telephone No. is not output on the remote transmitting machine if the remote transmitting machine has the function to display or
print the telephone No. of receiving machine, using this CSI signal.
RX
CED
T
DIS
SW-A1 No. 6 DIS receive acknowledgment during G3 transmission
SW-A3 No. 3 MR coding
Used to make a choice of whether reception of DIS(NSF) is acknowledged after receiving two DISs(NSFs) or receiving one DIS (two NSFs).
It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
Used to select the MR coding enable or disable.
SW-A3 No. 4 ~ No. 8 Reserved
Set to "0".
SW-A1 No. 7 Non modulated carrier for V29 transmission mode
SW-A4 No. 1 ~ No. 5 Signal transmission level
(0~-31 dBm setting by 1dBm step)
Though transmission of a nonmodulated carrier is not required for transmission by the V29 modem according to the CCITT Recommendation, it
may be permitted to a send nonmodulated carrier before the image signal to avoid an echo suppression problem.
It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
Used to control the signal transmission level in the range of -0dB to
-31dB.
The factory setting is at -10dB (MODEM output).
SW-A4 No. 6 Protocol monitor (Error Print)
SW-A1 No. 8 Reserved
If set to "1", protocol is printed at communication error.
Set to "0".
SW-A4 No. 7 Protocol monitor
SW-A2 No. 1 ~ No. 4 Modem speed
Normally set to "0". If set to "1", communication can be checked, in case
of trouble, without using a G3 tester or other tools.
When communication FSK data transmission or reception is made, the
data is taken into the buffer. When communication is finished, the data is
analyzed and printed out. When data is received with the line monitor
(SW4-No. 8) set to "1" the reception level is also printed out.
Used to set the initial modem speed. The default is 9600BPS.
It may be necessary to program it to a slower speed when frequent line
fallback is encountered, in order to save the time required for fallback
procedure.
SW-A2 No. 5 Reserved
SW-A4 No. 8 Line monitor
Set to "0".
Normally set to "0". If set to "1", the transmission speed and the reception level are displayed on the LCD. Used for line tests.
SW-A5 No. 1, No. 2 Digital equalization setting (Reception)
Line equalization when reception is to be set according to the line characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-A5 No. 3, No. 4 Digital equalization setting (Transmitter)
Line equalization when transmission is to be set according to the line
characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
2 – 13
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW-A5 No. 5, No. 6 Digital equalization setting
(Reception for Caller ID)
SW-B1 No. 3 Reserved
Set to "0".
Line equalization when reception for CALLER ID is to be set according
to the line characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-B1 No. 4 ~ No. 8 Recall interval
(0~15.5min setting by 0.5min step)
SW-A5 No. 7 Error criterion
Choice is made for a redial interval for speed and rapid dial calls.
Use a binary number to program this with 0.5min steps. If set to 0 accidentally, 0.5min will be assumed.
Used to select error criterion for sending back RTN when receiving image data.
SW-B2 No. 1 ~ No.4 Recall times (0~15times setting)
Choice is made as to how many redials there should be.
SW-A5 No. 8 Anti junk fax check
SW-B2 No. 5 Dial tone detection (Before auto dial)
When using the Anti junk fax function, set to "1".
Used to set YES/NO of dial tone detection in auto dialing.
SW-A6 No. 1 Auto gain control(MODEM)
When this mode is enabled, if the reception signal level is under 31dBm,
the modem itself controls the signal gain automatically.
SW-B2 No. 6 Reserved
SW-A6 No. 2 End buzzer
SW-B2 No. 7 Busy tone detection (After auto dial)
Setting this bit to 0 will disable the end buzzer (including the error buzzer/
on-hook buzzer).
Used to set YES/NO of busy tone detection after auto dialing.
SW-A6 No. 3 Disconnect the line when DIS is received in RX mode
Used for detection of busy tone in 2 or 4 pulses.
Set to "0".
SW-B2 No. 8 Busy tone detection pulse number (After auto dial)
Bit1 = 0 : When DIS signal is received during RX mode, disconnect the
line immediately.
Bit1 = 1 : When DIS signal is received during RX mode, wait for the next
signal.
SW-B3 No. 1, No. 2 Waiting time after dialing
This is waiting time for the opponent's signals after dialing.
45 / 55 / 90 / 140 seconds settings are available.
SW-A6 No. 4 Equalizer freeze control (MODEM)
SW-B3 No. 3 ~ No. 8 Reserved
This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in unfavorable state
and picture cannot be received.
* Usually, the control is executed according to the state of line where the
equalizer setting is changed always.
Set to "0".
SW-A6 No.5 Equalizer freeze 7200BPS only
SW-B4 No. 2 Dial mode
Setting which specifies SW-A6 No. 4 control only in condition of 7200BPS
modem speed.
When using the pulse dial, set to 0. When using the tone dial, set to 1.
SW-A6 No. 6 CNG transmission in manual TX mode
When setting to 1, the mode is changed by pressing the
pulse dial mode to the tone dial mode.
SW-B4 No. 1 Dialing pause (sec/pause)
Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available.
SW-B4 No. 3 Pulse → Tone change function by
When set to "1", fax transmit the CNG signal in case of manual
transmissiom mode (User press the START key after waiting for the fax
answering signal from handset or speaker).
key
key from the
SW-B4 No. 4 Dial pulse make/break ratio (%)
When using the 33% make ratio pulse dial, set to 0.
When using the 40% make ratio pulse dial, set to 1.
SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode
When set to "0", if the other fax is Sharp model, fax transmit the document by H2 mode.
When set to "1", even if the other fax is Sharp model, fax transmit the
document by MR mode.
SW-B4 No. 5, No. 6 Auto dial mode Delay timer of before line connect
Delay time between the dial key input and line connection under the
auto dial mode.
SW-A6 No. 8 Modem speed automatic down when RX level is under
-40dBm
RAPID A
When set to "1", if fax signal level is under -40dBm during reception,
machine selects the slower modem speed automatically.
It is effective when noises occur on the received document due to the
long distance communications.
CML RELAY ON
DIALLING
No.5=0
No.5=0
No.5=1
No.5=1
SW-A7 No. 1, No. 2 EOL (End Of Line) detect timer
Used to make a choice of whether to use the 5 or 13 or 20 or 25 seconds
timer for detection of EOL.
This is effective to override communication failures with some facsimile
models that have longer EOL detection.
No.6=0 : 0sec
No.6=1 : 1.5sec
No.6=0 : 3.0sec
No.6=1 : 4.5sec
SW-B4 No. 7, No. 8 Reserved
Set to "0".
SW-A7 No. 3 ~ No. 8 Reserved
Set to "0".
SW-B1 No. 1 Hold key
Used to set YES/NO of holding function by the HOLD key.
SW-B1 No. 2 Auto dial fax transmission by REDIAL key
When set to "1", if original documents are set to the feeder and you
press REDIAL key, machine will dial and transmit the ducuments automatically.
When set to "0", operator needs to press the START key after FAX reception tone is heard.
2 – 14
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW-B5 No. 1 ~ No. 3 Auto dial mode Delay timer of after line connect
SW-C1 No. 5 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
Delay time between the line connection and dial data output under the
auto dial mode.
This setting is available when dial tone detection(SW-B2 No. 5) is set to
"NO".
SW-C1 No. 6 Reserved
Set to "0".
DIAL DATA
RAPID A
CML RELAY ON
SW-C1 No. 7 MTF correction in half tone mode
This allows selection of MTF correction (dimness correction) in the half
tone mode.
When "NO" (=1) is selected, the whole image becomes soft and mild.
Clearness of characters will be reduced. Normally set to "YES" (=0).
No. 1
No. 2
No. 3
0
0
0
1.7sec
0
0
1
2.0sec
0
1
0
2.5sec
0
1
1
3.0sec
1
0
0
3.6sec
1
0
1
4.0sec
1
1
0
5.5sec
1
1
1
7.0sec
SW-C1 No. 8 Reserved
Set to "0".
SW-D1 No.1 ~ No. 4 Number of rings for auto receive
(0~15rings setting)
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to nine rings
using a binary number. Since the facsimile telephone could be used as
an ordinary telephone if the handset is taken off the hook, it should be
programmed to the user's choice. If the soft switch was set to 1, direct
connection is made to the facsimile.
If a facsimile calling beep was heard when the handset is taken off the
hook, press the START key and put the handset on the hook to have the
facsimile start receiving. If it was set to 0 accidentally, receive ring is set
to 1.
SW-B5 No. 4 Fax signal detection after telephone mode dial
When set to "1", if machine detects the fax answering signal after telephone calling (handset off-hook or speaker mode dial), machine starts
to receive the documents automatically.
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully.
If you have difficulty receiving faxes, reduce the number of rings
to a maximum of 5.
SW-B5 No. 5 ~ No. 8 Reserved
Set to "0".
SW-D1 No. 5 Automatic switching manual to auto receive function
SW-B6 No. 1 ~ No. 5 DTMF signal transmission level
(Low frequency 0~15.5dBm setting by 0.5dBm step)
00000: 0dBm
This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5
rings).
↓
SW-D1 No. 6, No. 7 CI detect frequency
11111: -15.5 dBm (-0.5dBm x 31)
Detection frequency of ring signal for auto reception is set.
The transmission level of DTMF signal is adjusted. (lower frequency)
When set to No. 6=0, No. 7=0, frequency is set to PTT recommendation.
When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more.
When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more.
When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.
SW-B6 No. 6 ~ No. 8 Reserved
Set to "0".
SW-B7 No. 1 ~ No. 5 DTMF signal transmission level
(High frequency 0~15.5dBm setting by 0.5dBm step)
SW-D1 No. 8 Reserved
The transmission level of DTMF signal is adjusted. (higher frequency)
Set to "0".
00000: 0dBm
SW-D2 No. 1 ~ No. 5 Reserved
↓
Set to "0".
11111: -15.5 dBm (-0.5dBm x 31)
SW-D2 No. 6 Caller ID Function
SW-B7 No. 6 ~ No. 8 Reserved
Used for Caller ID function.
Set to "0".
SW-D2 No. 7, No. 8 Reserved
SW-C1 No. 1, No. 2 Reading slice (Binary)
Set to "0".
Used to determine the set value of reading density in standard/fine/super-fine mode.
The standard setting is "00"(Factory setting is "00").
SW-C1 No. 3, No. 4 Reading slice (Half tone)
Used to determine the set value of reading density in half tone mode.
The standard setting is "00"(Factory setting is "00").
2 – 15
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW-D3 No. 1 ~ No. 5 CI off detection timer
(0~1550ms setting by 50ms step)
SW-E3 No. 1 Disconnect the line when DTMF "#" is received during
TEL/FAX automatic switching mode
Set the minimum time period of CI signal interruption which affords to be
judged as a CI OFF section with 50ms steps.
(Example)
When set to "1", if machine detects the DTMF code # during phone/fax
automatic switching mode, stop the pseudo ringer and disconnect the
line.
This effect when operator want to stop the pseudo ringer from extension
phone connected with parallel.
A
B
SW-E3 No. 2 ~ No. 8 Reserved
Set to "0".
1
400msec
SW-F1 No. 1, No. 2 DTMF detection time
2
2000msec
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception(5
).
The longer the detect time is, the less the error detection is caused by
noises.
0 1 1 1 0 (50ms~14) : 700ms(CI interruption>700ms:Judged as a CI
OFF section)
The section 1 is not judged as a CI OFF section, the CI signal A is counted as one signal.
The section 2 is judged as a CI OFF section,
the CI signal B is considered as the second signal.
0 0 1 1 1 (50ms~7) : 350ms(CI interruption>350ms:J udged as a CI
OFF section)
The section 1 is judged as a CI OFF section,
and the CI signal A is counted as two signals.
The section 2 is judged as a CI OFF section,
and the CI signal B is considered as the third
signal.
SW-F1 No. 3 Protection of remote reception (5
Used to set the function of remote reception (5
the remote reception function is disabled.
) detection
). When set to "1",
SW-F1 No. 4 Remote reception with GE telephone
"1": Compatible with TEL mode by GE
"0": Not compatible
• When sending (5
) for remote reception with a GE manufactured
telephone remote reception may not take place because of special
specifications in their DTMF.
To overcome this, a soft SW is provided to change the modem setting
to allow for remote reception.
SW-D3 No. 6 ~ No. 8 Reserved
Set to "0".
• If this soft SW is set to "1", other telephone sets may be adversely
affected.
SW-D4 No. 1 ~ No. 6 DTMF type Caller ID RX level
(0~-44dBm setting by 1dBm step)
SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL
(0~9)
This is used for DTMF type Caller ID detection level setting.
Remote operation codes can be changed from 0 through 9. If set to
" is not changed.
greater than 9, it defaults to 9. The "5
Ex- 7
(Default : 5
)
SW-D4 No. 7, No. 8 Reserved
Set to "0".
SW-F2 No. 1 CNG detection in STAND-BY mode
SW-E1 No. 1 ~ No. 3 Pseudo ringing time at the TEL/FAX automatic
switching mode
When setting to "1", the CNG signal detection function during standby
stops.
Choice is made as to how long to rumble the dummy ringer on TEL/FAX
automatic switching mode.
SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)
SW-E1 No. 4 Number of CNG signal detection at the TEL/FAX automatic switching mode
SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode)
Used for detection of CNG in 1 to 4 pulses.
Used for detection of CNG in one tone or two tones in the TEL/FAX
automatic switching mode.
Used for detection of CNG in 1 to 4 pulses.
SW-E1 No. 5 CNG detect time at TEL/FAX mode
Set to "0".
The switch which sets the time from the start of CNG detection to the
end of detection.
SW-G1 No. 1 ~ No. 4 Quiet detect time
(0~15sec setting by 1sec step)
SW-E1 No. 6 Post answer tone (TEL/FAX mode)
When an answering machine is connected, if a no sound state is detected for a certain period of time, the machine judges it as a transmission from a facsimile machine and automatically switches to the FAX
mode.
SW-F2 No. 6 ~ No. 8 Reserved
When set to "0", machine send the tones in TEL/FAX auto changeover
mode.
SW-E1 No. 7 Type of post answer tone
SW-G1 No. 5 ~ No. 8 Quiet detect start timing
(0~15sec setting by 1sec step)
When set to "0", post answer tone is 800Hz single tone.
When set to "1", post answer tone is 880Hz/988Hz/1046Hz(LA-SI-DO)
tone.
Inserts a pause before commencing quiet detection.
SW-E1 No. 8 Pseudo ringer ON/OFF cycle
SW-G2 No. 1 ~ No. 8 Reserved
When set to "0", pseudo ringer is 1 sec ON and 2 sec OFF cycles.
When set to "1", pseudo ringer is 1 sec ON and 4 sec OFF cycles.
Set to "0".
SW-E2 No. 1 ~ No. 4 Pseudo ringer sound output level to the line
(0~-15dBm setting by 1dBm step)
This is used to change the OGM detection time for answering machine
hook up detection.
Used to adjust the sound volume of pseudo ringer to the line (ring back
tone) generated on selecting TEL/FAX.
SW-G3 No. 3, No. 4 Section time of quiet detection
SW-G3 No. 1, No. 2 OGM detect timer
The switch which sets the time from the start of detection function to the
end of the function.
SW-E2 No. 5 ~ No. 6 Post answer tone transmission level
(0~-15dBm setting by 1dBm step)
SW-G3 No. 5 ~ No. 8 Reserved
Used to adjust the sound volume of post answer tone to the line generated on selecting TEL/FAX.
Set to "0".
2 – 16
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
SW-G4 No. 1 ~ No. 6 Quiet detect level setting
(0~-44dBm setting by 1dBm step)
SW-I8 No. 1 ~ No. 8 Reserved
Set to "0".
This is used to change the quiet detect level setting.
SW-J1 No. 1 Sender's phone number setting
If quiet detection is difficult due to noise, reduce this setting level.
Used to make a choice of whether the registered sender's phone number
can be changed or not. If the switch is set to "1", new registration of the
sender's phone number is disabled to prevent accidental wrong input.
(Example)
Factory setting : 1 0 1 1 0 0 (- 44dBm)
↓
SW-J1 No. 2 Reserved
1 0 1 0 0 0 (- 40dBm)
Set to "0".
SW-G4 No. 7 Fax switching when A.M. full
SW-J1 No. 3, No. 4 Ringer Volume
If the answering machine’s memory (tape) is full and there is no response,
the machine automatically switches to Fax reception.
Used to adjust ringing volume.
SW-J1 No. 5, No. 6 Speaker Volume
SW-G4 No. 8 Reserved
Used to adjust sound volume from a speaker.
Set to "0".
SW-J1 No. 7 Polling key (UX-40/FO-50 only)
SW-H1 No. 1 Busy tone continuous sound detect time
If this switch is set to 1, the last of Rapid key works as polling key.
Set detecting time busy tone continuous sound for 5 seconds or 10 seconds.
SW-J1 No. 8 Reserved
Set to "0".
SW-H1 No. 2 Reserved
SW-J2 No. 1 ~ No. 6 Reserved
Set to "0".
Set to "0".
SW-H1 No. 3 Busy tone detect continuation sound detect
SW-J2 No. 7 Saving energy start timing
Used to select detection of the continuous sound of certain frequency.
Set to "0".
Used to set the time between the machine’s stand-by state (clock indication) after operation and saving energy mode.
It is possible to set the time to either 5 sec or 180 sec (default).
SW-H1 No. 5 Busy tone detect intermittent sound detect
SW-J2 No. 8 Saving energy mode
Used to select detection of the intermittent sound of certain frequency.
Used to select whether to make the saving energy mode valid or not.
SW-H1 No. 6, No. 7 Busy tone detection pulse number
SW-J3 No. 1 ~ No. 3 Communication results printout
(Transaction report)
SW-H1 No. 4 Reserved
Used to set detection of Busy tone intermittent sounds.
It is possible to obtain transaction results after each communication.
Normally,the switch is set (No. 1 : 0, No. 2 : 0, No. 3 : 0) so that the
transaction report is produced only when a communication error is encountered.
If No.1 was set to 0 and No. 2 to 1 and No. 3 to 0, the transaction report
will be produced every time a communicaion is done, even if the
communicaion was successful.
Setting No. 1 to 0 and No. 2 to 1 and No. 3 to 1 will disable this function.
No transaction report printed.
SW-H1 No. 8 Reserved
Set to "0".
SW-H2 No. 1, No. 2 Busy tone detection ON/OFF time (Lower limit)
The initial value of detection is set according to electric condition.
The set value is changed according to the local switch board. (Erroneous detection of sound is reduced.)
If erroneous detection is caused by sound, etc., adjust the detection
range.
SW-J3 No. 4 Time format
The lower limit can be set in the range of 150msec to 350msec.
When set to "0", 24hour time format is used.
When set to "1", 12hour time format is used.
SW-H2 No. 3, No. 4 Busy tone detection ON/OFF time (Upper limit)
Similarly to SW-H2 No. 1, No. 2, the set value can be varied.
The upper limit can be set in the range of 650msec to 2700msec.
SW-J3 No. 5 Date format
SW-H2 No. 5 ~ No. 8 Reserved
When set to "0", Day-Month-Year format is used.
When set to "1", Month-Day-Year format is used.
Set to "0".
SW-J3 No. 6 ~ No. 8 Reserved
SW-I1 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-K1 No. 1 Entering diag mode by pressing SPEED key
SW-I2 No. 1 ~ No. 8 Reserved
A bit which is used in the production process only. When the SPEED key
is pressed, the switch is changed from the stand-by state to the diag
mode.
Set to "0".
SW-I3 No. 1 ~ No. 8 Reserved
SW-K1 No. 2 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-I4 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I5 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I6 No. 1 ~ No. 8 Reserved
Set to "0".
SW-I7 No. 1 ~ No. 8 Reserved
Set to "0".
2 – 17
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[3] Troubleshooting
Refer to the following actions to troubleshoot any of the problems mentioned in 1-4.
[1]
A communication error occurs.
[2]
Image distortion produced.
[3]
Unable to do overseas communication.
[4]
Communication speed slow due to FALLBACK.
•
Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.
May be used in case [1] [2] [3].
•
Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,
5. May be used in case [3].
•
Apply line equalization SOFT SWITCH A5-1, 2.
May be used in case [1] [2] [3] [4].
•
Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,
4. May be used in case [2] [3].
•
Replace the TEL/LIU PWB.
May be used in all cases.
•
Replace the control PWB.
May be used in all cases.
* If transmission problems still exist on the machine, use the following
format and check the related matters.
TO:
ATT:
Ref.No. :
CC:
ATT:
Date
:
Dept
:
Sign
:
FM:
From: Mr.
Our customer
Other party
Problem mode
Name
Address
Contact person
Name
Address
Contact person
Line: Domestic / international
Reception / Transmission
Frequency:
Confirmation
item
Ref.No.:
***** Facsimile communication problem *****
Fax Tel No.:
Our customer
Date:
Model:
G3
Automatic reception / Manual reception
Automatic dialing / Manual dialing / Others
% ROM version:
Other party
B1
B2
Tel No.
Fax No.
Model name
Tel No.
Fax No.
Model name
Phase: A, B, C, D.
Please mark problem with an X.
No problem is: 0.
A1 A2 B1 B2 C1 C2
A1
A2
C1
D2
C2
E1
E2
Our service
D1
Other party's service
Comment
Countermeasure
**** Please attach the G3 data and activity report on problem. ****
* Please complete this report before calling the “TAC” hotline if problem still occurs.
2 – 18
D1 D2 E1 E2
Transmission level setting is (
customer
Transmission level (
) dBm
Reception level (
) dBm
By level meter at B1 and B2
) dB at our
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[4] Error code table
1. Communication error code table
G3 Transmission
Code
Final received signal
Error Condition (Receiver side)
0
Incomplete signal frame
Cannot recognize bit stream after flag
1
NSF, DIS
Cannot recognize DCS signal by echo etc.
2
CFR
Cannot recognize NSS signal (FIF code etc)
Disconnects line during reception (carrier missing etc)
3
4
FTT
MCF
Disconnects line by fall back
Disconnects line during reception of multi page
5
PIP or PIN
Cannot recognize NSS, DCS signal in the case of mode change
The line is hung up without replying to telephone request from the receiving party.
6
RTN or RTP
Cannot recognize NSS, DCS signal after transmit RTN or RTP signal.
7
8
No signal or DCN
−
No response in receiver side or DCN signal received* (transmitter side)
Owing to error in some page the error could not be corrected although the specified number of
error retransmissions were attempted.
11
−
Error occurred after or while reception by the remote (receiving) machine was revealed to be
impossible.
12
−
Error occurred just after fallback.
13
−
Error occurred after a response to retransmission end command was received.
G3 Reception
Code
0
Final received signal
Incomplete signal frame
Error Condition (Receiver side)
Cannot recognize bit stream after flag
1
NSS, DCS
2
NSC, DTC
Cannot recognize CFR or FTT signal
Disconnects line during transmission (line error)
Cannot recognize NSS signal (FIF code etc)
3
EOP
Cannot recognize MCF, PIP, PIN, RTN, RTP signal
4
5
EOM
MPS
Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change
The line is hung up without replying to communication request.
6
7
PR1-Q
No signal or DCN
Cannot recognize PIP, PIN signal in the case of TALK request
No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side)
8
9
−
−
Error occurred upon completion of reception of all pages.
Error occurred when mode was changed or Transmission/Reception switching was performed.
10
11
−
−
Error occurred during partial page or physical page reception.
Error occurred after or during inquiry from the remote (transmitting) machine as to whether
12
−
reception is possible or not.
Error occurred during or just after fallback.
13
−
Error occurred after the retransmission end command was received.
2 – 19
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
3-2. Automatic document feed
CHAPTER 3. MECHANISM BLOCKS
1) Use of the paper feed roller and separation rubber plate ensures error-free transport and separation of documents. The plate spring
presses the document to the paper feed roller to assure smooth feeding of the document.
[1] General description
2) Document separation method: Separation rubber plate
1. Document feed block and diagram
Separator rubber(*)
Separation rubber
(UX-40/FO-50 ONLY)
Hopper guide
Document
Separator plate(*)
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
Document sensor
Back roller
Operation panel PWB
Feed plate
Document
Front sensor(*)
Paper feed roller
(UX-40/FO-50 ONLY)
Paper feed roller(*)
CIS unit
Fig. 3
(*): UX-40/FO-50 ONLY
3-3. Documents applicable for automatic feed
Fig. 1
Square
4x6 series
(788mm x 1091mm x meter series
1000mm sheets)
2. Document feed operation
Minimum
1) The original, which is set in the document hopper, feeds automatically when the front sensor is activated. This in turn activates the
pulse motor which drives the document supply roller. The document
stops when the lead edge is detected by the document sensor.
Feeder capacity
Paper weight
Maximum
Minimum
Maximum
52g/m2
80g/m2
5 sheets, max.
45kg
69.2kg
Paper thickness (ref.) 0.06mm
0.09mm
0.06mm
0.09mm
Paper size
148mm x 140mm ~
A4 (210mm x 297mm), Letter (216mm x 279mm)
NOTE: Double-side coated documents and documents on facsimile recording paper should be inserted manually. The document feed
quantity may be changed according to the document thickness.
2) The lead edge of the original is fed a specified number of pulses after
the lead edge of the document is detected for the reading process to
begin.
3) The trailing edge of the original is fed a specific number of pulses
after the trailing edge of the document deactivates the document
sensor. The read process then stops and the original is discharged.
Documents corresponding to a paper weight heavier than 69.2kg (80g/
m2 ) and lighter than 135kg (157g/m2 ) are acceptable for manual feed.
4) When the front sensor is in the OFF state (any document is not set
up in the hopper guide), the drive will be stopped when the document is discharged.
Documents heavier than 135kg in terms of the paper weight must be
duplicated on a copier to make it operative in the facsimile.
3. Hopper mechanism
3-4. Loading the documents
3-1. General view
1) Make sure that the documents are of suitable size and thickness, and
free from creases, folds, curls, wet glue, wet ink, clips, staples and
pins.
2) Place documents face down in the hopper.
i) Adjust the document guides to the document size.
ii) Align the top edge of documents and gently place them into the
hopper. The first page under the stack will be taken up by the feed
roller to get ready for transmission.
NOTES: 1) Curled edge of documents, if any, must be straightened
out.
2) Do not load the documents of different sizes and/or
thicknesses together.
Fig. 2
The hopper section contains document guides that are used to adjust
the hopper to the width of the original document. This ensures that the
original feeds straight into the fax machine for scanning.
Document width: 148 mm to 216 mm (A5 longitudinal size to Letter
longitudinal size)
NOTE: Adjust the document guide after setting up the document.
3–1
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Separation rubber
(UX-40/FO-50 ONLY)
5. Recording block
Last page of document
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
,,,,,,,,,,
5-1. General view
Back of document
Recording paper
First page of document
Scanner frame
Platen roller
Feed plate
PO guide
Paper feed roller
(UX-40/FO-50 ONLY)
Fig. 4
3-5. Documents requiring use of document carrier
1) Documents smaller than 148mm x 140mm.
2) Documents thinner than the thickness of 0.06mm.
Paper guide
Head guide
3) Documents containing creases, folds, or curls, especially those whose
surface is curled (maximum allowable curl is 5mm).
Thermal head
4) Documents containing tears.
Fig. 6
5) Carbon-backed documents. (Insert a white sheet of paper between
the carbon back and the document carrier to avoid transfer of carbon
to the carrier.)
5-2. Driving
6) Documents containing an easily separable writing material (e.g., those
written with a lead pencil).
Via the pulse motor gear shaft, the reduction gear, and the recording
paper feed gear, rotation of the pulse motor is conveyed to the recording
paper feed roller to feed the recording paper.
7) Transparent documents.
5-3. Recording
8) Folded or glued documents.
Use of a thermal head permits easier maintenance and low operating
costs.
Document in document carrier should be inserted manually into the
feeder.
1) Thermal head
The thermal head consists of 1728-dot heat elements arranged in a single row and has the resolution of 8 dots/mm. The maximum recording
speed is 10ms/line. The thermal head also incorporates a 1728-dot shift
register latch and output control driver circuit. Low power consumption is
achieved by dividing the head into nine segments.
4. Document release
4-1. General
2) Structure of the recording mechanism
To correct a jammed document or to clean the document running surface, pull the insertion side of document center of the operation panel.
To open the upper document guide, the operation panel must be opened
first.
Recording is accomplished by pressing the thermal head on the recording paper against the platen roller.
The main scan (horizontal) is electronically achieved, while the subscan
(vertical) is achieved by moving the recording paper by the recording
platen roller.
4-2. Cross section view
Usually, the cause for uneven print tone is caused by misalignment of
the thermal head or uneven contact with the roller.
It can by checked in the following manner.
1) Check if the thermal head power and signal cables are properly routed.
2) Check that the thermal head pivot moves smoothly up and down.
Operation panel unit
3) Check that the thermal head support bracket is secured without any
play.
Scanner frame unit
CIS release lever
4) Check to see that the recording platen roller has proper concentricity,
in the case of a print tone variation evenly repeated down the page.
PWB case unit
Lower cabinet
5) Replace the thermal head with a new one and check to see if the
same trouble occurs.
Fig. 5
3–2
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[2] Disassembly and assembly procedures
•
•
This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures.
•
•
The numbers in the illustration, the parts list and the flowchart in a same section are common to each other.
Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units,
refer to the Parts List.
To assure reliability of the product, the disassembly and the assembly procedures should be performed carefully and deliberately.
1
Parts list (Fig. 1)
Paper support guide, handset cover
and scanner unit
No.
Q’ty
No.
1
Mechanism unit
Part name
1
7
Screw (3×8)
Part name
1
2
Screw (3×12)
2
8
Handset cover
1
3
Paper support guide
1
9
Hook switch lever
1
4
Paper sensor lever
1
10
Screw (3×12)
2
5
Paper sensor lever spring
1
11
Connector
2
6
Panel stopper
1
12
Scanner unit
1
12
UX-40/
FO-50
ONLY
1
2
3
4
5
6
UX-40/
FO-50
ONLY
12
UX-40/
FO-50
ONLY
3
10
12
7
8
9
10
11
12
2
Hook
2
10
Fix position of spring
4
4
5
5
9
7
11
Hook
Hook
Hook
6
8
Control
PWB
Hook
Hook
1
Fig. 1
3–3
Q’ty
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
2
Parts list (Fig. 2)
CIS unit and scanner frame
No.
Q’ty
No.
1
Document guide lower
1
11
2
Back roller gear
1
3
Back roller bearing, left
1
12
Connector
1
4
CIS release lever, left
1
13
CIS support, left
1
5
Back roller
1
14
CIS support, right
1
6
CIS release lever, right
1
15
CIS unit
1
7
Back roller bearing, right
1
16
CIS protect sheet
1
8
Reduction gear, 17/28z
1
17
CIS spring
2
Reduction gear, 17/23z
1
18
Connector
1
9
Part name
Feed roller shaft
1
19
2
3
4
5
6
7
8
9
10
Front sensor
1
(UX-40/FO-50 only)
20
18
19
1
(UX-40/FO-50 only)
(UX-40/FO-50 only)
1
Q’ty
(UX-40/FO-50 only)
(UX-40/FO-50 only)
10
Part name
Feed roller
Scanner frame
1
Hook
11
12
13
14
15
16
17
20
1
Hook
10
3
4
11
5
8
2
9
6
19
18
12
17
20
13
17
15
16
Fix position of CSI spring
20
14
Fix position
OK
17
15
15
NG
13 , 14
13 , 14
Fig. 2
3–4
7
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
3
Operation panel unit, drive unit, hopper
guide
Parts list (Fig. 3)
No.
Q’ty
No.
1
Mechanism unit
Part name
1
9
2
Connector
2
2
3
7
3
Operation panel unit
1
10
Screw
1
4
Connector
2
11
Pinion gear
1
5
Screw (3×12)
1
12
Hopper spring
1
6
Drive unit
1
13
Hopper guide, left
1
7
Screw (3×8)
2
14
Hopper guide, right
1
8
Hopper guide unit
1
15
Hopper guide
1
8
3
2
4
9
5
10
Control
Control
PWB
PWB
11
2
6
12
13
14
15
1
7
9
8
10
15
11
12
13
30°
Fix position
12
boss
Confirm of HOPPER GUIDE position.
HOPPER
GUIDE(R)
Rib
GAP 0
R
14
GAP 0
Rib
Fig. 3
3–5
L
HOPPER
GUIDE(L)
Q’ty
1
document guide upper unit
1
4
5
6
Part name
Operation panel unit/
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
4
Upper cabinet and document guide
upper
Parts list (Fig. 4)
No.
1
2
3
4
6 5
14 7
15 8
16 9
17 10
18 11
19 12
20 13
1
Q’ty
No.
1
Screw (3×8)
Part name
2
12
Part name
Q’ty
2
Connector
1
3
Door sensor
1
13
Document guide upper
4
Blind sheet
1
14
Screw (2×6)
3
5
Document guide upper unit
1
15
Connector
1
6
Operation panel unit
1
16
Operation panel PWB unit
1
7
Separate spring
1
17
Direct key
1
8
Separator plate
1
9
Separator rubber
1
18
Start key
1
10
Feed spring
1
19
12 key
1
11
Feed plate
1
20
Upper cabinet
1
Document guide piece
Fix position
11
7
13
10
8
12
7
9
2
3
13
6
16
20
LCD CABLE
LCD PWB
LCD PWB
Rib
Rib
15
Note) The LCD PWB should
be securely locked by the
click of the panel case.
17
16
18
19
14
Fig. 4
3–6
1
(UX-40/FO-50 only)
5
4
1
(UX-8/GQ-5 only)
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
5
Parts list (Fig. 5)
Drive unit frame
No.
Part name
Q’ty
No.
Part name
Q’ty
1
Cam spring
1
10
Planet lever B
2
Cam switch
1
11
Planet gear
1
1
3
Cam gear
1
12
Planet gear spring
1
4
Mode lever
1
13
Reduction gear, 17/30Z
1
5
Planet gear
1
14
Reduction gear, 17/43Z
1
6
Planet gear spring
1
15
Idler gear, 25Z
1
7
Planet lever A
1
16
Screw (3×8)
1
8
Planet gear
1
17
Motor
1
9
Planet gear spring
1
18
Motor plate
1
19
Drive unit frame
1
17
18
16
1
2
3
4 5
7 8
6
9
1
10 11 12
13
19
16
14
OK
17
15
2
18
19
4
,
NG
14
5, 6 / 7
,
OK
10
8, 9
10 , 11 , 12
15
Grease
13
Grease
4
,
5, 6 / 7
3
,
8, 9
5
10 , 11 , 12
4
6
Fig. 5
3–7
8
9
11
12
Nail be doing lock.
NG
7
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
6
Parts list (Fig. 6)
Release lever, head guide and PO guide
No.
1
2
3
4
4
5
REL
EAS
E
1
2
3
Fig. 6
3–8
5
Part name
Q’ty
1
Mechanism unit
1
2
Screw (3×8)
1
3
PO guide
1
4
Release lever
1
5
Head guide
1
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
7
Head frame unit
Parts list (Fig. 7)
No.
1
2
Screw (3×6)
1
3
Connector
1
4
Screw (3×8)
1
5
Head earth cable
1
6
Head frame unit
1
7
Screw (3×8)
2
8
Panel lock lever spring
2
5
6
4
3
5
7
1
8
Control
PWB
7
8
Fig. 7
3–9
Q’ty
Mechanism unit
2
1
2
3
4
5
6
7
8
Part name
1
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
8
Parts list (Fig. 8)
Head frame and thermal head
No.
1
2
3
Q’ty
No.
1
Platen gear
Part name
1
7
Screw (3×6)
1
2
Platen bearing
2
8
Head holder, right
1
3
Platen roller
1
9
Thermal head
1
4
Connector
1
10
Head spring 2
2
5
Screw (3×6)
1
11
Head spring 1
3
6
Head holder, left
1
12
Head frame
1
4
5
6
7
8
9
Part name
2
10
3
11
12
1
6
9
2
5
4
12
10
8
11
7
10
Fig. 8
3 – 10
11
Q’ty
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
9
PWB case top, bottom, PWB and
speaker
Parts list (Fig. 9)
No.
Q’ty
No.
1
Mechanism unit
Part name
1
11
Screw (3×8)
Part name
2
2
Screw (3×8)
1
12
Hook switch joint lever
1
3
Connector
1
13
PWB case, top
1
4
Connector
2
14
PWB case, bottom unit
1
5
PWB case unit
1
15
Screw (3×6)
1
6
Screw (3×8)
1
16
TEL/LIU PWB unit
1
7
Control PWB unit
1
17
Screw (4×6)
1
8
Screw (3×8)
1
18
AC cord ass’y
1
9
Speaker holder lever spring
1
19
Power supply PWB unit
1
10
Speaker ass’y
1
20
PWB case, bottom
1
3
1
2
3
4
5
6
7
8
9
10
7
11
12
13
14
15
16
17
18
19
20
6
8
9
10
5
2
4
4
Fix position
16
13
17
15
12
17
19
18
18
19
Hook
11
20
14
11
Fig. 9
3 – 11
Q’ty
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
10
Wire treatment
Parts list (Fig. 10)
No.
Part name
Q’ty
1
Core (F2125)
2
2
Screw (3×6)
1
3
Screw (4×6)
1
4
Screw (3×6)
1
5
Band (100mm)
1
6
Band (100mm) (UX-40/FO-50 only)
2
7
Core (F2123) (UX-40/FO-50 only)
1
8
Screw (3x8)
1
Door sensor cable
Rib
Panel
cable
Door sensor
cable
Rib
Operation
panel PWB
Panel cable
Rib
Door
sensor
cable
Hopper cover
Operation
panel unit
The panel cable and
door sensor cable
pass to the core 2
times.
1
Panel
cable
1
Rib
Rib
TEL/LIU PWB
Power
Supply PWB
Speaker
cable
2
Cam
switch
cable
The head cable and
head earth cable
pass to the core 2 times.
Head
earth
cable
1
Rib
Drive unit
Door
sensor
cable
1
Control
PWB
Speaker
Rib
5
Motor cable
6
7
6 CIS
cable
CIS
cable
Cam
switch
cable
Motor
cable
7
6
Front
sensor
cable
Front
sensor cable
CIS
cable
Rib
6
6
8
CIS
cable
Front sensor
Head
cable
cable(UX-40/
FO-50 ONLY)
TEL/LIU PWB
AC
ARG 4
cord
cable
3 earth
cable
CIS Front
sensor
7 cable cable
(UX-40/
FO-50
ONLY)
AC cord
earth cable
Rib
Speaker
Rib
Rib
Scanner
frame Rib
3
Speaker
cable
PWB
case, bottom
Power
supply
PWB
Rib
Fig. 10
3 – 12
AC
cord
4–1
LINE
HANDSET
SPEAKER
SURGE
PROTECT/
FILTER
AMPLIFIER
AMPLIFIER
CML
AMPLIFIER
D-FF
CI
TRANSFORMER
BZ
TEL/LIU
PWB UNIT
CLOCK
32.768kHz
ROM
1Mbit
16MHz
AMPLIFIER
RESET IC
VBT
SRAM
256kbit
PIO
CPU
RTC
SURGE
TRANS
ABSORBER
RECTIFIER
DIODE
TRANSFORMER
RECTIFIER
STABILIZER
+5V
PANEL I/F
SIO
THERMAL
HEAD I/F
SENSOR I/F
MOTOR I/F
CIS I/F
TIMER
WATCHDOG
TIMER
INTERRUPT
CONTROLLER
CPU I/F
1CHIP FAX ENGINE (FC200)
+24V
FILTER
POWER SUPPLY
PWB UNIT
OPERATION
PANEL
PANEL
DRIVER
PM
LCD
THERMAL
HEAD
CONTACT
IMAGE
SENSOR
PAPER
SENSOR
[1] Block diagram
MODEM
FM209
CLOCK
32.256MHz
+3.3V
REGULATOR
+5V
CONTROL PWB UNIT
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
CHAPTER 4. DIAGRAMS
16
4–2
OPERATION
PANEL PWB
UNIT
CNLCD
2
16
CNDR
CNCIS
CNTH
CNPN
CNMT
6
(UX-40/FO-50 ONLY)
FRONT
SENSOR
2
CNFRS
CONTROL
PWB UNIT
CNCSW
2
CAM SW
SPEAKER
2
CNSP
CNPW
CNLIUA
8
12
TEL/LIU
PWB UNIT
CNTLJ
CNLNJ
POWER SUPPLY
PWB UNIT
CN2
CNLIUA
ARG
CNHJ
HANDSET
AC CORD
[2] Wiring diagram
14
LCD UNIT
DOOR
SENSOR
7
CIS(CONTACT IMAGE SENSOR)UNIT
FG
THERMAL HEAD
TX/RX
MOTOR
FG
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
CNPN
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[3] Point- to-point diagram
CNMT
TX/RX
MOTOR
THERMAL
HEAD
OPERATION
PANEL
PWB
TPAD
TPBD
TPAD
TPBD
VMT
VMT
VTH
VTH
STRB1
STRB2
THI
N.C.
MG
MG
MG
+5V
STRB3
STRB4
LATCH
PCLK
DATA
VTH
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CNPN
1
DG
2
+5V
3
SEN4
4
E
5
SEN0
6
SEN1
7
SEN2
8
SEN3
9
SEN5
10
SEN6
11
SEN7
ORGSNS 12
13
KEN4A
14
KEN3A
15
KEN2A
16
KEN1A
1
2
3
4
5
6
TPAD
TPBD
TPAD
TPBD
VMT
VMT
CNLIUA
1
TELOUT
2
TELIN
TELMUTE 3
4
CI
5
HS
6
RHS
7
RXIN
8
TXOUT
9
CML
10
+5V
11
DG
12
+24V
CNTH
1
VTH
2
VTH
3
STRB1
4
STRB2
5
THI
6
RANK
7
MG
8
MG
9
MG
10
+5V
11
STRB3
12
STRB4
13
LATCH
14
PCLK
15
DATA
16
VTH
CNPN
1
DG
2
+5V
3
SEN4
4
E
5
SEN0
6
SEN1
7
SEN2
8
SEN3
9
SEN5
10
SEN6
11
SEN7
12 ORGSNS
13
KEN4A
14
KEN3A
15
KEN2A
16
KEN1A
CONTROL
PWB
CIS
VO
DG
+5V
øT
CISCLK
GLED
+24V
1
2
3
4
5
6
7
1
2
DRSNS
DG
CNPW
1
DG
2
+5V
3
MG
4
MG
5
+24V
6
+24V
CN2
1
2
3
4
5
6
DG
+5V
MG
MG
+24V
+24V
CNCSW
1
CSW
2
DG
1
2
CSW
DG
CAM
SWITCH
CNSP
1
2
1
2
SP+
SP-
SPEAKER
1
2
FRSNS
DG
FRONT
SENSOR
CNFRS
1
FRSNS
2
DG
(UX-40/FO-50 ONLY)
4–3
TEL/LIU
PWB
CNDR
DRSNS 1
2
DG
SP+
SPCNCIS
1
VO
2
DG
3
+5V
4
øT
5
CISCLK
6
GLED
7
+24V
CNLIUA
1
TELOUT
2
TELIN
3 TELMUTE
4
CI
5
HS
6
RHS
7
RXIN
8
TXOUT
9
CML
10
+5V
11
DG
12
+24V
DOOR
SENSOR
POWER
SUPPLY
PWB
6–1
B
RA9
270 x 4
RA11
470 x 4
L101
HM601
R168
10K
33
34
35
36
29
30
31
37
96
97
100
99
98
101
90
91
92
93
94
STRB3
STRB2
STRB1
STRB0
PCLK
PDAT
PLAT
STRBPOL
VIDCTL0
VIDCTL1
CLK1
CLK1
CLK2
START
GPIO4
GPIO3
GPIO2
GPIO1
GPIO0
38 : OPO7
OPI0
OPI1
OPI2
OPI3
LEDCTL
LCDCS
OPO0
OPO1
OPO2
OPO3
OPO4
OPO5
OPO6
71
66
67
65
119
106
SM0
105
SM1
104
SM2
103
SM3
118
GPO0
117
GPO1
116
GPO2
115
GPO3
114
52
51
50
49
55
54
47
46
44
43
42
40
39
38
C125
C126
C115
C116
C141
C150
C142
22P
22P
22P
22P
22P
22P
22P
RA1
470 x 4
RA13
470 x 4
X2
32.768KHz
C139
22P +VREF
–VREF
VIN
THADI
C136
1
BZOUT
RA8
470 x 4
L104 R133
HM601 120
KEN1A
KEN2A
KEN3A
KEN4A
E
SEN0
SEN1
SEN2
SEN3
SEN4
SEN5
SEN6
SEN7
F
DG
DG
C137
0.1
C134
1
BATRST
RD
WR
ROMCS
CS1
CS0
MCS
SYNC
REGDMA
WAIT
RAS
CAS0
CAS1
DWR
WRPROT
A23
A22
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
R131
DG 1M DG
RESET
C138
22P
TPA
TPB
TPA
TPB
C2 1000P
C1 1000P
C105 1000P
C104 1000P
VTHON
RCVOL
(5-5F)
(5-5F)
(5-5F)
(5-5F)
DG
DG
DG
DG
(5-5F)
(6-6C)(6-2A)
LEDON
(5-5F)
MDMRST
(3-2C)
CNPN-4
CNPN-5
CNPN-6
CNPN-7
CNPN-8
CNPN-3
CNPN-9
CNPN10
CNPN-11
E
59
DG
60
D
VDRAM
C135
2200P
C
XIN
DG
+VREF
–VREF / CLREF
VIN
THADI
TONE
DG
R12
10M
XOUT
62
C3
0.1
RA5
470 x 4
PWRDWN
63
A
STRB4
STRB3
STRB2
STRB1
PCLK
DATA
LATCH
φT
R109 150
R110 470
RA4
470 x 4
33K
33K
33K
33K
VBAT
61
1
2
CNTH-12
CNTH-11
CNTH-4
CNTH-3
CNTH-14
CNTH-15
CNTH-13
CISCLK
φT
C162
N.M.
DG
R113
R111
R120
R119
IC2
FC200
FAX ENGINE
M
D0
D1
D2
D3
D4
D5
D6
D7
TSTCLK
SYSCLK
MIRQ
RESET
DEBUG
TEST
CNCIS-5
CNCIS-4
DPMUTE
PESNS
FRSNSI
ORGSNSI
PSNS
C169
C163
C149
C168
3
CNLIUB-4
(4-4D)
(4-5D)
(4-5D)
(4-3D)
ADVA
R118
470
70
DG
ADGA
ADGD
GPIO9
GPIO8
GPIO7
GPIO6
GPIO5
ADXG
84
85
86
87
89
68
69
72
N.M.
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
R126
33K
VSS
14
32
41
48
81
102
123
140
R103
470
21
4
VSS
R169
470
28
RA10
N.M.
VSS
GPIO14
GPIO13
GPIO12
GPIO11
GPIO10
VSS
45
78
79
80
82
83
53.56
RA10
N.M.
VSS
CNLIUB-5
CNLIUB-3
CNPW-8
CNLIUB-1
(4-6D)
VSS
64.88
RA14 470
VSS
ERLY
DPON
PSAVE
RLYCNT
CSWI
R123 33K
R124 33K
R125 33K
95.108
HS
CI
RA12
470 x 4
GPIO20
GPIO19
GPIO18
GPIO17
GPIO16
GPIO15
VSS
134
SPMUTE
107
73
74
75
76
77
7
CML
VREFCONT
CUTI
R107 33K
L N
R105 33K
R106 33K
144
143
142
141
139
138
137
136
130
133
135
131
129
58
(4-4D)
(5-2A)
(1-6B)
(6-4I)
CNLIUA-5
CNLIUA-4
DG
RA2
270 x 4
N.M. R166 R2
(1-5A)(6-3E)
DG
C121
1
DG
R132 C107
10K 1000P
F
RA3
270 x 4
5
CNLIUA-9
C120
0.1
C114
C106 1
1
C111
C122 1
C123 1
DG
C140 1
DG
C124 1
DG
1
DG
C112
1
DG
DG
DG
E
SYSCLK
MIRQ
CML
+5V
D
D0
D1
D2
D3
D4
D5
D6
D7
CML
+5V
C
(3-3A)
(3-3B)
6
B
[1] Control PWB circuit
Main control block
A
DG
G
BATRST
128
127
120
122
57
121
126
124
125
113
112
111
109
110
1
2
3
4
5
6
8
9
10
11
12
13
15
16
17
18
19
20
22
23
24
25
26
27
G
C165
1
+5V
I
K
J
H
RA7
270 x 4
RA6
270 x 4
A
B
C
D
E
F
G
DG
GND
3
OUT
VCC
2
IC101
XC61
1
R112 200
R104 270
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
R144
10K
CE1
MCS
RD
WR
ROMCS
H
H
(2-5B)
(3-4B)
(2-5B)
(3-4B)
RESET
(2-4E)
(3-3B)
I
(1-1F)
(2-4B)(3-3B)
(2-4E)(3-3B)
(2-4B)
A[16-0]
D[7-0]
1/6
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
VBT
(1-1I)
(5-2D)
(5-2D)
(5-6D)
(5-1I)
(6-4I)
+5V
CNPN-16
CNPN-15
CNPN-14
CNPN-13
DG
DG
DG
DG
DG
DG
DG
6–2
1
2
3
4
5
6
A
Memory block
A
(1-3I)
(1-3I)
(1-6I)
(1-5I)
B
ROMCS
RD
D[7~0]
A[16~0]
B
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
2
3
29
28
4
25
23
26
27
5
6
7
8
9
10
11
12
22
24
C
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
E
G
21
20
19
18
17
15
14
13
GND
16
30
(A17)
31
PGM
32
VCC
1
VPP
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
IC5
27C010
ROM
C
DG
C161
0.1
+5V
D
D
(1-3I)
(1-3I)
D7
D6
D5
D4
D3
D2
D1
D0
CE1
WR
VBT
R121
22K
E
E
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
20
27
22
1
26
2
23
21
24
25
3
4
5
6
7
8
9
10
CS1
WE
CS2/OE
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
VSS
VDD
IO8
IO7
IO6
IO5
IO4
IO3
IO2
IO1
14
28
19
18
17
16
15
13
12
11
IC3
W24258S-70LE
SRAM
F
F
DG
C113
0.1
VBT
D7
D6
D5
D4
D3
D2
D1
D0
G
G
H
H
2/6
I
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
6–3
L105
HM601
4 8
B
MAG
MDMRST
6
(1-1D)
R4
270
7
1
C
DG
C172
1000P
C4
0.01
D
DG
32
N.C./IARESET-S
57
IARESET-P
DG
R122
10K
111
110
109
105
104
102
101
99
RA14
470 x 1
8
EYEXY
4
EYECLK
3
EYESYNC
E
MAG
R130
0
C118
0.1
DG
DG
DG
DG
F
DG
DG
DG
29
122
54
50
75
26
30
55
9
76
25
51
31
18
56
27
52
6
N.M.
R5
DG
119 XCLK
24 YCLK
115
RESET
13
EN85
GPO0
GPO1
GPO2
GPO3
GPO4
GPO5
GPO6
GPO7
MAG
G
TELMUTE
TXMUTE
G
DG
R101
0
C101
12P
X1
32.256MHz
XTL0
VC-P
N.C.
RESERVED
N.C./MICP-S
N.C./MICM-S
N.C./MICBIAS-S
N.C./SPKRP-S
N.C./SPKRM-S
N.C./LINEIN-S
N.C./LINEOUT-S
N.C./VREF-S
N.C./VC-S
LINEIN-P
C102
12P
R100
200
DG
H
MAG
38,39,44,49,59,64,65,74
1,2,53,103,118,123,124,128
35
36
MAG
37
46
47
34
43
40
41
67
C6
0.1
C173
1000P
C20
1000P
I
3/6
(6-4E)
DG
I
MAG
C5
10/50
C7
10/50
(6-5E)
(6-4C)
(6-4E)
MAG
C131
0.1
SPOUT
SIGTX
R129
1K
SIGRX
TELOUTI
R134
2.2K
C130
0.1
60
72
71
63
62
61
H
69
LINEOUT-P
66
VREF-P
SPKRM-P
SPKRP-P
MICBIAS-P
MICM-P
MICP-P
VAA-S(+5VIAA)
L102
HM601
116
N.M.
R116
DG
R167
270
L1
HM601
113 VGG(+5VDD)
IC1
TC7WT74
Q PRE
CLK
D
2
C2 CLR
3
5
48
N.C./AVDD-S(+3.3VIAD)
126 DVAA(+3.3VDA)
N.C./SOUT-S
SR3IN
SOUT-P
N.C./ICLK-S
ICLK-P
IA1CLK
N.C./SIN-S
SIN-P
SR4OUT
N.C./MCLK-S
IACLK
MCLK-P
N.C./FSYNC-S
SA1CLK
FSYNC-P
N.C./CTRLSIN-S
CTRLSIN-P
SR1IO
A
R102
470
MCS
RD
WR
MIRQ
MAG
C132
1
C9
47/25
AGND5
AGND4
AGND3
AGND2
AGND1
XTL1
117
1
(1-6F)
SYSCLK
C103
1
(1-3I)
(1-3I)
(1-3I)
(1-6F)
R14
3
F
68 VAA-P(+5VIAA)
2
3
L3
HM601
IC4
FM209
MODEM
GPI0
GPI1
GPI2
GPI3
GPI4
GPI5
GPI6
GPI7
D7
D6
D5
D4
D3
D2
D1
D0
CS
READ
WRITE
IRQ1
IRQ2
RESERVED/CSBR
14
120
93
94
95
96
97
98
78
79
80
81
82
83
86
88
91
92
90
108
121
89
AVDD-P(+3.3VIAD)
VDD5(+3.3VDD)
VDD4(+3.3VDD)
VDD3(+3.3VDD)
VDD2(+3.3VDD)
VDD1(+3.3VDD)
+5V
D7
D6
D5
D4
D3
D2
D1
D0
DG
C110
0.1
73
112
100
85
77
10
D[7~0]
R135
33K
C133
1
L100
HM601
DGND6
DGND5
DGND4
DGND3
DGND2
DGND1
RS4
RS3
RS2
RS1
RS0
RTS
CTS
TXD
DCLK
RXD
RLSD
R6
33K
RA14
470 x 1
+3.3V
125
114
106
87
84
16
19
20
21
22
23
15
107
17
12
5
11
C19
1000P
R117
470
L103
HM601
E
127
70
58
45
33
(1-6H)
A4
A3
A2
A1
A0
R8
10K
DRSNS
R165
100K
CNDR-1
RHS
RANK
R115
470
CNLIUA-6
CNTH-6
+5V
C119
2200P
D
+5V
42
4
(1-5I)
A[4~0]
C
+5V
5
B
+3.3V
6
Modem block
A
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
CNLIUA-3
TXMUTEI(6-4E)
CNLIUB-2
6–4
1
2
3
4
5
6
B
A
CNCUT -2
CNCUT -3
CNCUT-1
N.M.
CNPN-12
(UX-40/
FO-50
ONLY)
CNFRS-2
CNFRS-1
CNCSW-2
CNCSW-1
DG
+24V
N.C.
DG
CUT
ORGSNS
DG
FRSNS
DG
CSW
R114
0
R145
1K
B
C117
4
N.M.
PI2
SG206
PI1
3
DG DG
2
1
4
2
DG
3
N.M.
(UX-40/
FO-50
ONLY)
1
DG
DG
C143
2200P
DG
C109
2200P
DG
C108
2200P
Sensor/Reset/Power supply block
A
C
C
PSNS
PESNS
PSNS
PESNS
CUTI
ORGSNSI
FRSNSI
CSWI
D
(1-3A)
(1-4A)
(1-5A)
(1-3A)
(1-3A)
(1-4A)
D
E
E
CNPW-3
CNPW-4
CNPW-5
CNPW-6
CNPW-1
CNPW-7
CNPW-2
DG
F
MG
MG
+24V
+24V
DG
DG
+5V
BAT1
CR2032
F
R159
R163
N.M.
C170
0.1
N.M.
C171
0.1
DG
C167
0.1
R160
5.6K
DG
N.M.
R164
FG
+5V
G
C16 N.M.
DG
<VBT>
+24VA
C17
22/50
+24V
DG
C18
47/25
MG
DG
1
REG100
XC62FP3302P
2
3
D102
1SS355
D103
HRW0202
+5V
G
+24V
DG
DG
+5V
+5V
+3.3V
VBT
H
CNLIUA-12
CNPN-1
CNLIUA-11
CNPN-2
CNLIUA-10
H
I
4/6
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
6–5
1
2
3
4
5
A
(1-5A)
CNCIS-1
VREFCONT
VO
<VO>
B
DG
R142
30K
R143
43K
R157
20K
+5V
(5-5I)
+24V
+5V
DG
C
DG
N.M.
DG
DG
DG
C
Q104
2SA1037
R158
5.1K
C129
0.1
<VIN>
<DG>
C21 N.M.
DG
C128
1000P
C100
0.1
C127
1
LEDON
R170
0
Q100
2SA1037
R128
5.1K
+5V
C174
6
B
GLED
+24V
DG
+5V
VIN
VREF–
VREF+
CNCIS-6
CNCIS-7
CNCIS-2
CNCIS-3
(1-1F)
Video processing/Motor drive / Thermal block
A
D
(1-1F)
(1-1F)
D
E
(5-5I)
E
VTHON
F
(1-1E)
(3-1D)
(1-1E)
(1-1E)
(1-1E)
(1-1E)
F
+24V
VTHON
LEDON
TPA
TPB
TPA
TPB
MG
COIL
D104
1SS355
1B
2B
3B
4B
5B
6B
7B
E
3
1
COM
1C
2C
3C
4C
5C
6C
7C
G
+5V
RY1
DQ1U24VDC
4
2
1
2
3
4
5
6
7
8
+24V
IC8
ULN2003A
G
MG
R161
470K
MG
R108
22K
+24V
MG
R162
20K
9
16
15
14
13
12
11
10
D1
100(1W)
H
C15
10/50
C166
1
MG
FU100
KAB2402
H
THI
THADI
+5V
MG
MG
MG
VTH
VTH
VTH
VTHON
LEDON
TPAD
TPBD
TPAD
TPBD
VMT
VMT
I
CNTH-5
(1-1F)
CNTH-10
CNTH-7
CNTH-8
CNTH-9
CNTH-1
CNTH-2
CNTH-16
(5-3E)
(5-4B)
CNMT-1
CNMT-2
CNMT-3
CNMT-4
CNMT-5
CNMT-6
5/6
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
6–6
1
2
3
4
5
6
(1-1E)
A
CNLIUA-7
CNLIUA-8
RXIN
TXOUT
C22
1
TELOUT
RCVOL
CNLIUA-1
R153
330K
+5VA
C157
0
C8
0
C151
0
B
N.M.
R15
R152
0
DG
Q1
+5VA
+5V
B
Analog signal block
A
Q103
6 –
5
+
+24VA
C156
0
DG
N.M.
8
C
SIGTX
N.M.
IC7
1
R148
0
C155
N.M.
R18
TXMUTEI
DG
DG
N.M.
R149
R151
N.M.
IC7
7
N.M.
2 –
3 +
N.M.
C153
N.M.
C14
RCVOL
DG
4
R17
0
C152
L4
HM601
N.M.
R147
R146
0
(1-1D)
C
C144
HM601
C154
0.1
C147
HM601
(3-1D)
(3-4H)
R138
0
DG
N.M.
R150
R136
0
N.M.
Q101
D
Q102
DG
C146
1
C145
1
N.M.
R137
R16
D
N.M.
D101
1SS355
+5V
TELOUTI
D100
1SS355
+5V
E
TELIN
CML
SIGRX
CNLIUA-7
(1-5A)
(3-4H)
(3-3H)
(3-4H)
E
SPOUT
L106
HM601
F
F
C148
0.1
R140
15K
R154
100K
G
8
DG
DG
C164
4700P
R141
20K
DG
C11
47/25
IC6
NJM2113
5
R139
220K
C159
220P
R156
1K
DG
6
+5V
4–
2+
31 7
R155 C160
100K 0.01
DG
C158
1
G
H
H
BZOUT
SPMUTE
SP–
SP+
I
(1-1F)
(1-5A)
CNSP-2
CNSP-1
6/6
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Control PWB parts layout (Top side)
6–7
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Control PWB parts layout (Bottom side)
6–8
6–9
1
CNHJ-3
CNHJ1-3
CNHJ-2
CNHJ1-2
CNHJ1-1
CNHJ-1
CNHJ1-4
CNHJ-4
CNLNJ-6
TLJ-1
CNLNJ-5
CNLNJ-4
CNLNJ-3
CNLNJ-2
TLJ-2
A
RX–
RX+
TX–
TX+
N.M.
JP11
JP7
JP9
N.M.
N.M.
R109
1K
C104
2200P
DG
N.M.
JP16
L6
R-5C
B
D3
DG
C6
22/50
N.M.
ARG
C105
2200P
L7
R-5C
JP17
N.M.
N.M.
JP18
L8
R-5C
JP1
L1
M
B
+5V
DG
C
C107
1000P
DG
R124
DG
N.M.
PC5
TLP521
IC101
2904
7
D
DG
– 6
+ 5
IC101
2904
R114
43K
1
N.M.
R1
+
–
N.M.
C14
C2
ZD2
PC1
N.M.
R132
0
R128
8.2K
E
F
R105
PC2
TELIN
DG
E
TELMUTE
Q107
RNC1402
VREF
3
4
R104
T1
I2164
TELOUT
1
2
CNLIUA-3
CNLIUA-2
CNLIUA-1
C4
D
PC3
S
Q1
R102
N.M.
F
N.M.
R106
ZD7 N.M.
ZD8
R107
G
ZD1
C116
C10
NOTE:
These marks are all satety-cirtical parts.
C103
R130
0
R127
68K
N.M.
R131
3.3K
PC4
DG
~
~
REC1
R103
C1
R2
D
ZD6
C111
220P
R126
220K
C113
1000P
2 –
3 +
C108
3900P
ZD5
ZD4
HZ27C
DG
R125
3.3K
N.M.
DG
C109
220P
C8
R101
43K
R3
22K(1/2W)
L2
C101
L5
N.M.
C102
JP15
N.M.
ZD3
C3
0.82
VREF
R123
150
Q101
2SC2412K
R110
5.1K
N.M.
JP3
CML1
C5
22/50
N.M.
DG
D2
C
C106
0.1
AR1
RA-391P
VA1
ERZV5D471
JP13
+5V
R108
1.5K
N.M.
JP12
VA2
ERZV5D471
N.M.
JP6
L3B
R-5C
L3A
R-5C
JP5
JP8
JP10
C
D1
1SS133
2
3
4
5
6
L4
B
[2] TEL/LIU PWB circuit
N.M.
A
VREF
DG
JP4
N.M.
C11
22/50
C7
10/50
G
DG
R113
20K
R134
20K
C124
0
C127
0.039
C9
4.7/50
C114
0.1
C120
820P
4
R143
47K
C121
C125
IC102
2904
R114
4.7K
DG
4
H
DG
C112
0.1
1
8
I
I
CNLIUA-7
+5VA
+5VA
CNLIUA-8
1/2
+24VA
RXIN
N.M.
C126
TXOUT
IC101
2904
R142
3.3K
R139
R138
N.M.
8
IC102
2904
2 –
3
+
R137
N.M.
C123
H
IC102
2904
– 6
5
+
R115
86.6K
C115
33P
R116
3.3K
7
DG
DG
N.M.
JP14
R141
47K
R133
51K
R129
620
R111
20K
+5V
R140
20K
C122
0
+5V
R112
0
+5VA
N.M.
DG
JP2
R117
G
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
6 – 10
B
RHS
HS
CI
E-RLY
DPMUTE
DPON
C
CNHS-2
CNHS-1
CNLIUA-6
CNLIUA-5
CNLIUA-4
CNLIUB-5
CNLIUB-4
CNLIUB-3
N.M.
D
E
CNLIUA-12
CNLIUA-11
CNLIUA-10
+24V
DG
+5V
C12
22/50
C13
22/25
F
D4
1SS133
CML
R135
1K
R118
100
F
DG
Q104
RNC1402
C118
0.1
C117
0.1
CML
G
CNLIUA-9
+24VA
DG
+5VA
G
H
H
I
2/2
I
3
4
5
6
1
A
SW1
HOOK SW
DG
N.M.
N.M.
C119
DG
DG
DG
PC3
C110
DG
Q108
DG
Q106
DG
PC5
TLP521
PC4
PC2
PC1
E
1
DG
R136
N.M.
R122
R121
R120
R119
Q105
D
2
+5V
C
2
3
4
5
6
B
TEL/LIU PWB circuit
A
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
TEL/LIU PWB parts layout (Top side)
6 – 11
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
TEL/LIU PWB parts layout (Bottom side)
6 – 12
6 – 13
B
C7
3900P
A
2
25.00us
CN1
F2
1.6A/250V
C
25.00us
D
5us/div
-100.0V
-25.00us
D6
N.M.
5us/div
C17
1000P
PC1
20V/div
C24
0.22
R7
D5
33 1SS355
C6
0
N.M.
T1
PTTP124
5us/div
10V/div
CH2 W1
100.0V
R8
47K
ZD2
RD2.0SB
L2
RS208
D9
C23
*R5
1.5K
*R6
18K
R4
330
PC2
PC123YS
C4
2200P
R24
ZD6
25.00us
200V/div
GND
D
GND
R10
0.33
ZD1
RD27SB
-800V
-25.00us
C
GND
R9
470
R3
R2
Q1
FS5KM
GND
Q3
2SC2412K
C3
1000P
C2
68/400
-50.0V
-25.00us
CH2 W1
50.0V
1
F1
1.6A/250V
C1
0.22
R1
3.3M
V1
ERZV07D471
L1
ELF15N003A
C21
TH1
89.2
5.02ms
1ms/div
50V/div
CH2 W1
1200V
Q2
2SD2114K
1
D4
D3
C15
2200P
D2
D1
ERA15-06 x 4
-50V
-4.9Sms
B
C10
2200/16
D8
SR140
N.M. C13
R15
330K
R14
1.5K
Q5
2SC4210
PC2
PC123YS
ZD7
RD20ESAB
5us/div
ZD5
RD6.2SB
Q4
2SC2412K
R13
4.7K
R11
39
25.00us
20V/div
GND
E
*:ADJUSTMENT RESISTOR
R18
27K
FB1
PC1
PC123YS
C8
560/35
D7
S3L20U-4004P15
-100.0V
-25.00us
CH2 W1
100.0V
E
C9
0.47
Q6
2SC4210
2
3
4
5
6
CH2 W1
450V
A
[3] Power supply PWB circuit
F
R17
8,2K
VR1
1K
R21
150K
R12
180K
C12
0.1
F
R16
22K
R19
4.7K
R20
4.7K
C16
100/10
L3
JUMPER
F3
CCP2E100(4A)
G
ZD4
RD30FB
G
R25
10K
H
H
8
7
PSAVE
DG
+24V
+24V
6
5
3
MG
MG
2
4
DG
+5V
1
CN2
I
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
IC1
UPC29M05AHF
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Power supply PWB parts layout (Top side)
T1
Q1
D9
J7
R10
C3
D7
J3
C8
C2
L1
C13
ZD6
V1
J5
C10
FB1
D8
IC1
R24
ZD7
L2
C7
C16
L3
VR1
2
D4
F1
TH1
R2
R3
J1
PC2
C9
1
D1
PC1
CN2
C24
D3
8
CN1
C1
J4
ZD4
1
R1
C15
C21
D2
F2
J6
J12
J11
J10
JW1
R4
C4
C23
R9
ZD1
R11
R15
R16
C12
Q2
R25
C5
R14
D6
R13
R17
Q6
R12
R21
R19
6 – 14
R20
C17
Q5
C6 R7
R5 ZD2
ZD5
F3
Q4
R18
D5
R6
Q3
R8
Power supply PWB parts layout (Bottom side)
6 – 15
1
2
3
4
5
6
B
KEN1A
KEN2A
KEN3A
KEN4A
SEN7
SEN6
SEN5
SEN4
RS
SEN3
LD7
SEN2
LD6
SEN1
LD5
SEN0
LD4
N.M.
D8
D7
1SS270
D6
1SS270
D1
1SS270
D5
1SS270
D2
1SS270
D3
1SS270
D4
1SS270
REC
REDIAL
(UX-40/
FO-50
ONLY)
REPEAT
SPEED
START
(UX-40/
FO-50
ONLY)
(UX-40/
FO-50
ONLY)
05
02
7
4
1
01
RESO/MODE
FUNC
VOLUME
C
D
A
B
C
D
03
0
8
5
2
PLAY
HOLD
STOP
(UX-40/
FO-50
ONLY)
NOTE: Since the parts of PWB cannot be supplied, change it as a unit.
CNPN-16
CNPN-15
CNPN-14
CNPN-13
CNPN-11
CNPN-10
CNPN-9
CNPN-3
CNLCD-4
CNPN-8
CNLCD-14
CNPN-7
CNLCD-13
CNPN-6
CNLCD-12
CNPN-5
CNLCD-11
[4] Operation panel PWB circuit
A
E
DELETE
SPEAKER
COPY
(UX-40/
FO-50
ONLY)
04
#
9
6
3
E
CNPN-1
CNPN-2
CNPN-4
C1
R2
6.2K
F
DG
N.M.
R1
1K
G
VO
R/W
DG
DG
E
ORGSNS
+5V
C2
ORGSNS
SW-169-72AU
G
+5V
E
DG
ORGSNS
F
CNLCD-3
CNLCD-5
CNLCD-1
CNLCD-2
CNLCD-6
CNPN-12
H
DG
VO
R/W
N.C.
N.C.
LD4
LD6
DG
SEN4
SEN0
SEN2
SEN5
SEN7
KEN4A
KEN2A
H
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
2
4
6
8
10
12
14
CNLCD
1
3
5
7
9
11
13
15
CNPN
+5V
RS
E
N.C.
N.C.
LD5
LD7
+5V
E
SEN1
SEN3
SEN6
ORGSNS
KEN3A
KEN1A
I
I
1
2
3
4
5
6
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
MEMO
6 – 16
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
PARTS GUIDE
UX-8
UX-40
GQ-5
MODEL FO-50
CONTENTS
1
Cabinet, etc.
6
Packing material & Accessories
2
Scanner unit
7
Control PWB unit
3
Upper cabinet
8
TEL-Liu PWB unit
4
Document guide upper
9
Power supply PWB unit
5
Drive unit
Index
Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must be
replaced with the parts specific to the product specification.
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[1] Cabinet, etc.
54
1
2
53
2
11
49
B3
DOCUMENT
GUIDE UPPER
7
46
9
B3
B3
8
B7x2
SCANNER
UNIT
B3
41
47
30
22
39
52
B4
29
B3
B1
34
B4
39
33
53
34
36
5
6
B7x2
31
B3
28
24
37
23
40
56
58
17
19
B7
28
45
B3
16
DRIVE
UNIT
B3
15
B5
B3
B3
B4
12
20
14
21
B4
B3
40
55
13
14
B3
18
27
B3x2
–1–
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
AP
AP
AP
AP
AK
AC
AD
AE
AC
AF
AD
AG
AK
AK
AK
AC
AC
AX
AK
AK
AK
AH
AH
AH
AC
AL
BA
AF
AC
AB
AE
AE
AC
AB
AF
AC
AC
AC
AC
AB
AP
AH
AC
BF
BP
BP
BP
AD
AC
AC
AC
AE
AE
AE
AE
AE
AA
AB
AN
AB
AA
AA
AA
AA
N
E
E
E
E
C
C
C
C
C
C
B
C
D
D
D
C
C
E
C
C
C
C
C
C
C
B
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
E
E
E
C
C
C
C
B
D
D
D
D
C
C
C
C
C
C
C
C
DESCRIPTION
[1] Cabinet etc.
1
2
5
6
7
8
9
11
12
13
14
15
16
17
18
!
19
20
21
22
23
24
27
28
29
30
31
33
34
36
37
39
40
41
45
46
47
49
52
53
54
55
56
58
B1
B3
B4
B5
B7
DCEKP481BXH18
DCEKP481BXH04
DCEKP481BXH19
DCEKP481BXH05
CCNW-212AXH01
MSPRC2954XHZZ
NGERP2318XHZZ
PGIDM2560XHSD
PGIDM2561XHSD
PHOP-2104XHSD
QSW-M2296XHZZ
CCNW-215AXH01
GCABB2343XHSA
GCABB2343XHSB
GCABB2343XHSC
MSPRP3119XHZZ
MSPRP3123XHZZ
DCEKL483BXH02
GCASP2110XHSD
GCASP2110XHSF
GCASP2110XHSE
GCASP2111XHSA
GCASP2111XHSB
GCASP2111XHSC
MLEVP2320XHZZ
QACCE2042XHZZ
RDENT2144XHZZ
GDAI-2083XHZZ
MLEVP2316XHZZ
MSPRD3116XHZZ
PGIDM2563XHSA
PGIDM2563XHSB
PGIDM2563XHSC
LBSHP2112XHZZ
LFRM-2208XHZZ
LHLDZ2184XHZZ
LHLDZ2185XHZZ
MSPRC3112XHZZ
MSPRC3148XHZZ
NGERH2478XHZZ
NROLR2425XHZZ
QCNW-209AXHZZ
QCNW-210AXHZZ
RHEDZ2059XHZZ
DCEKC689MXHZZ
DCEKC685MXHZZ
DCEKC780MXHZZ
GDAI-2082XHSD
LSTPP2054XHZZ
MLEVP2319XHZZ
PGIDM2566XHZZ
RCORF2125XHZZ
HPNLH2394XHSA
HPNLH2392XHSU
HPNLH2394XHSE
HPNLH2392XHS3
LBNDJ2006XHZZ
PSHEZ3410XHZZ
MLEVP2321XHZZ
LX-BZ2138XHZZ
XEBSD30P08000
XBBSD30P06000
XBPSN40P06K00
XEBSD30P12000
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Operation panel unit
Operation panel unit
Operation panel unit
Operation panel unit
Panel cable ass’y
Hopper spring
Pinion gear
Hopper,guide,left
Hopper,guide,right
Hopper cover
Door sensor
Speaker ass’y
Lower cabinet
Lower cabinet
Lower cabinet
Panel lock lever spring
Speaker holder lever spring
TEL/Liu PWB unit
PWB case,top
PWB case,top
PWB case,top
PWB case,bottom
PWB case,bottom
PWB case,bottom
Hook switch joint lever
AC cord ass’y
Power supply PWB unit
Paper support guide
Paper sensor lever
Paper sensor lever spring
PO guide
PO guide
PO guide
Platen bearing
Head frame
Head holder,left
Head holder,right
Head spring 1
Head spring 2
Platen gear
Platen roller
Head cable
Head earth cable
Thermal head
Control PWB unit(Within ROM)
Control PWB unit(Within ROM)
Control PWB unit(Within ROM)
Handset cover
Panel stopper
Hook switch lever
Head guide
Core(TRA31)
Decoration panel
Decoration panel
Decoration panel
Decoration panel
Band(100mm)
Jack sheet
Release lever
Screw(2x6)
Screw(3x8)
Screw(3x6)
Screw(4x6)
Screw(3x12)
–2–
[8]
[40]
[5]
[50]
[8/40]
[5]
[50]
[8/40]
[5]
[50]
[8/40]
[5]
[50]
[8/40]
[5]
[50]
[8]
[40/50]
[5]
[8]
[40]
[5]
[50]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[2] Scanner unit
13
12
5
1
10
19
20
20 15
11
8
7
2
19
15
16
2
19
9
5
20
1
15
16
16
17
16
6
15
: UX-40/FO-50 ONLY
2
3
6
14
19
18
4
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[2] Scanner unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
LBSHP2110XHZZ
LFRM-2209XHZZ
LHLDZ2180XHZZ
LHLDZ2181XHZZ
MLEVP2317XHZZ
MSPRC3117XHZZ
NGERH2479XHZZ
NGERH2480XHZZ
NGERH2481XHZZ
NROLR2375XHZZ
NROLR2428XHZZ
NSFTZ2273XHZZ
PGIDM2562XHZA
PGIDM2562XHZZ
PSHEZ3436XHZZ
QCNW-211AXHZZ
QCNW-213AXHZZ
QSW-M2293XHZZ
RUNTZ2054XHZZ
LBNDJ2006XHZZ
RCORF2123XHZZ
AB
AF
AC
AC
AB
AB
AB
AB
AB
AL
AP
AF
AD
AD
AC
AF
AC
AE
BE
AA
AD
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
B
Back roller bearing
Scanner frame
CIS support,left
CIS support,right
CIS release lever
CIS spring
Back roller gear
Reduction gear,17/28Z
Reduction gear,17/23Z
Feed roller
Back roller
Feed roller shaft
Document guide lower
Document guide lower
CIS protect sheet
CIS cable
Front sensor cable
Front sensor
CIS unit
Band(100mm)
Core
–3–
[40/50]
[40/50]
[40/50]
[8/5]
[40/50]
[40/50]
[40/50]
[40/50]
[40/50]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[3] Upper cabinet
6
(UX-40/FO-50 ONLY)
5
4
3
1
7
B2x3
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[3] Upper cabinet
1
3
4
5
6
7
B2
901
CCNW-212AXH01
GCABA2342XHSA
GCABA2342XHSB
GCABA2342XHSC
JBTN-2257XHSD
JBTN-2258XHSA
JBTN-2258XHSB
JBTN-2258XHSC
JBTN-2261XHSA
JBTN-2261XHSC
DCEKP482BXH02
DCEKP482BXH01
XUBSD20P06000
(Unit)
DCEKP481BXH18
DCEKP481BXH04
DCEKP481BXH19
DCEKP481BXH05
AK
AH
AH
AH
AD
AC
AC
AC
AC
AC
AP
AQ
AA
AP
AP
AP
AP
N
N
N
N
N
[4] Document guide upper
C
D
D
D
C
C
C
C
C
C
E
E
C
Panel cable ass’y
Upper cabinet
Upper cabinet
Upper cabinet
12 key
Start key
Start key
Start key
Direct key
Direct key
Operation panel PWB unit
Operation panel PWB unit
Screw(2x6)
E
E
E
E
Operation panel unit
Operation panel unit
Operation panel unit
Operation panel unit
UX-8/GQ-5
ONLY
[8/40]
[5]
[50]
[8/40]
[5]
[50]
[40]
[50]
[8/5]
[40/50]
[8]
[40]
[5]
[50]
3
8
2
5 UX-40/
FO-50 ONLY
4
1
6
7
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
N
N
C
C
C
C
C
C
C
C
DESCRIPTION
[4] Document guide upper
1
2
3
4
5
6
7
8
LPLTG2911XHZZ
LPLTP2908XHZZ
LPLTP3051XHZZ
MSPRT3140XHZZ
MSPRT3139XHZZ
PGIDM2554XHZZ
PSHEZ3517XHZZ
LPLTP3058XHZZ
AE
AE
AB
AA
AA
AF
AE
AD
Separator rubber
Separator plate
Feed plate
Separate spring
Feed spring
Document guide upper
Blind sheet
Document guide piece
–4–
[40/50]
[40/50]
[40/50]
[40/50]
[40/50]
[8/5]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[5] Drive unit
22
2
B3
20
21
6
17
9
12
9
1
13
15
10
4
12
9
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
1
2
4
5
6
8
9
10
12
13
15
17
20
21
22
B3
LFRM-2207XHZZ
LPLTM3049XHZZ
MCAMP2027XHZZ
MLEVP2311XHZZ
MLEVP2312XHZZ
MLEVP2314XHZZ
MSPRC2735XHZZ
MSPRC3110XHZZ
NGERH2278XHZZ
NGERH2379XHZZ
NGERH2391XHZZ
NGERH2475XHZZ
QCNW-4933XHZZ
QSW-F2224SCZZ
RMOTZ2148XHZZ
XEBSD30P08000
AF
AD
AC
AB
AB
AB
AC
AB
AC
AC
AC
AB
AC
AE
AT
AA
N
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
N
8
DESCRIPTION
[5] Drive unit
Drive unit frame
Motor plate
Cam
Planet lever A
Planet lever B
Mode lever
Planet gear spring
Cam spring
Planet gear
Idler gear,25Z
Reduction gear,17/30Z
Reduction gear,17/43Z
Cam switch cable
Cam switch
Motor
Screw(3x8)
–5–
12
5
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
[6] Packing material & Accessories
19
2
FAX PAPER
21
7
6
22
TAPE
TAPE
R
8
TAPE
ORIGINAL DOCUMENT
SUPPORT SIDE
5
17
16
AC CORD
3
1
9
TAPE
4
18
(2)
(3)
(4)
(1)
10
11
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[6] Packing material & Accessories
1
2
3
4
5
6
7
8
9
10
11
16
17
18
19
21
22
TINST4026XHZZ
DUNTK468BXHPU
QCNW-3976XHBG
QCNW-3976XHOG
QCNW-3976XHOW
PHOP-2105XHZZ
QCNW-3975XHGY
SPAKP296BXHZZ
SPAKA287BXHZZ
SPAKA288BXHZZ
SPAKA289BXHZZ
SPAKC178BXHZZ
SPAKC189BXHZZ
SPAKC187BXHZZ
SPAKC194BXHZZ
TLABM341AXHZZ
TLABM345AXHZZ
TLABM344AXHZZ
TLABM347AXHZZ
PGIDM2578XHZZ
PGIDM2579XHZZ
NSFTZ2320XHZZ
TCADZ2935XHZZ
SPAKA388BXHZZ
SPAKA389BXHZZ
AY
AH
AK
AT
AK
AD
AG
AE
AE
AE
AC
AH
AH
AH
AH
AD
AD
AD
AD
AE
AE
AF
AA
AE
AE
N
N
N
N
N
N
N
N
D
E
C
C
C
C
C
D
D
D
D
D
D
D
D
D
D
D
D
C
C
C
D
D
D
Operation manual
Handset
Handset cord
Handset cord
Handset cord
Original document support
Telephone line cord
Vinyl cover
Packing add.,left
Packing add.,right
Pad
Packing case
Packing case
Packing case
Packing case
Box label
Box label
Box label
Box label
Paper roll shim,right
Paper roll shim,left
Paper shaft
Caution sheet
Protection sheet,left
Protection sheet,right
–6–
[8/40]
[5]
[50]
[8]
[40]
[5]
[50]
[8]
[40]
[5]
[50]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[7] Control PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
UBATL2046SCZZ
VCKYTV1HB102K
VCKYTV1HB102K
VCKYTV1EF104Z
VCKYTV1HB103K
VCEAGA1HW106M
VCKYTV1EF104Z
VCEAGA1HW106M
VRS-TS2AD000J
VCEAGA1EW476M
VCEAGA1EW476M
VCEAGA1HW106M
VCEAGA1HW226M
VCEAGA1EW476M
VCKYTV1HB102K
VCKYTV1HB102K
VCKYTV1CF105Z
VCKYTV1HF104Z
VCCCTV1HH120J
VCCCTV1HH120J
VCKYTV1CF105Z
VCKYTV1HB102K
VCKYTV1HB102K
VCKYTV1CF105Z
VCKYTV1HB102K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1CF105Z
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1CF105Z
VCCCTV1HH220J
VCCCTV1HH220J
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1CF105Z
VCKYTV1CF105Z
VCKYTV1CF105Z
VCKYTV1CF105Z
VCCCTV1HH220J
VCCCTV1HH220J
VCKYTV1CF105Z
VCKYTV1HB102K
VCKYTV1EF104Z
VCKYTV1EB104K
VCKYTV1EF104Z
VCKYTV1CF105Z
VCKYTV1CF105Z
VCKYTV1CF105Z
VCKYTV1HB222K
VCKYTV1CF105Z
VCKYTV1EF104Z
VCCCTV1HH220J
VCCCTV1HH220J
VCKYTV1CF105Z
VCCCTV1HH220J
VCCCTV1HH220J
VCKYTV1HB222K
RCILZ2145XHZZ
VCKYTV1CF105Z
VCKYTV1CF105Z
RCILZ2145XHZZ
VCKYTV1CF105Z
VCCCTV1HH220J
VRS-TS2AD000J
VCKYTV1EB104K
VRS-TS2AD000J
VRS-TS2AD000J
VCKYTV1CF105Z
VCKYTV1HB221K
VCKYTV1HB103K
VCKYTV1EF104Z
VCKYTV1HB472K
VCKYTV1CF105Z
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1HF104Z
VCKYTV1EF104Z
AK
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AB
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AA
AB
AB
AA
AB
AA
AA
AA
AA
AA
AB
AB
AB
AB
AA
AA
AB
AA
AA
AA
AA
AB
AB
AB
AA
AB
AA
AA
AA
AB
AA
AA
AA
AF
AB
AB
AF
AB
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
AB
AB
AA
AA
AA
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Battery(CR2032T34)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 0.01µF)
Capacitor(50WV 10µF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 10µF)
Resistor(1/10W 0Ω ±5%)
Capacitor(25WV 47µF)
Capacitor(25WV 47µF)
Capacitor(50WV 10µF)
Capacitor(50WV 22µF)
Capacitor(25WV 47µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(16WV 1µF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 12PF)
Capacitor(50WV 12PF)
Capacitor(16WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(16WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 2200PF)
Capacitor(50WV 2200PF)
Capacitor(25WV 0.1µF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(25WV 0.1µF)
Capacitor(16WV 1µF)
Capacitor(50WV 22PF)
Capacitor(50WV 22PF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 2200PF)
Capacitor(25WV 0.1µF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(50WV 22PF)
Capacitor(50WV 22PF)
Capacitor(16WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(25WV 0.1µF)
Capacitor(25WV 0.1µF)
Capacitor(25WV 0.1µF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(50WV 2200PF)
Capacitor(16WV 1µF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 22PF)
Capacitor(50WV 22PF)
Capacitor(16WV 1µF)
Capacitor(50WV 22PF)
Capacitor(50WV 22PF)
Capacitor(50WV 2200PF)
Coil(HM601)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Coil(HM601)
Capacitor(16WV 1µF)
Capacitor(50WV 22PF)
Resistor(1/10W 0Ω ±5%)
Capacitor(25WV 0.1µF)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Capacitor(16WV 1µF)
Capacitor(50WV 220PF)
Capacitor(50WV 0.01µF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 4700PF)
Capacitor(16WV 1µF)
Capacitor(16WV 1µF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 0.1µF)
Capacitor(25WV 0.1µF)
–7–
[BAT1]
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[C7]
[C8]
[C9]
[C11]
[C15]
[C17]
[C18]
[C19]
[C20]
[C22]
[C100]
[C101]
[C102]
[C103]
[C104]
[C105]
[C106]
[C107]
[C108]
[C109][40/50]
[C110]
[C111]
[C112]
[C113]
[C114]
[C115]
[C116]
[C118]
[C119]
[C120]
[C121]
[C122]
[C123]
[C124]
[C125]
[C126]
[C127]
[C128]
[C129]
[C130]
[C131]
[C132]
[C133]
[C134]
[C135]
[C136]
[C137]
[C138]
[C139]
[C140]
[C141]
[C142]
[C143]
[C144]
[C145]
[C146]
[C147]
[C148]
[C150]
[C151]
[C154]
[C156]
[C157]
[C158]
[C159]
[C160]
[C161]
[C164]
[C165]
[C166]
[C167]
[C170]
[C171]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[7] Control PWB unit
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
VCKYTV1HB102K
VCKYTV1HB102K
QCNCM7014SC0G
QCNCM2442SC0B
QCNCM705BAF06
QCNCM7014SC0B
QCNCW2500SC1B
QCNCM7014SC0F
QCNCM7014SC1F
QCNCW2500SC0H
QCNCM2401SC0B
QCNCM7014SC1F
VRS-HT3AA101J
VHD1SS355//-1
VHD1SS355//-1
VHD1SS355//-1
VHDHRW0202B-1
VHD1SS355//-1
QFS-P2010SCZZ
VHITC7WT74FU1
VHIFC2FM209-1
VHIW24258S7LE
VHIFC2FM209-1
QSOCZ2051SC32
VHI27010FZJ0B
VHI27010FZK0A
VHINJM2113M-1
VHIULN2003AN/
VHIXC61AN45M1
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
RCILZ2145XHZZ
VHPSG206S//-1
VS2SA1037KS-1
VS2SA1037KS-1
VRS-TS2AD271J
VRS-TS2AD333J
VRS-TS2AD103J
VRS-TS2AD106J
VRS-TS2AD3R0J
VRS-TS2AD000J
VRS-TS2AD201J
VRS-TS2AD000J
VRS-TS2AD471J
VRS-TS2AD471J
VRS-TS2AD271J
VRS-TS2AD333J
VRS-TS2AD333J
VRS-TS2AD333J
VRS-TS2AD223J
VRS-TS2AD151J
VRS-TS2AD471J
VRS-TS2AD333J
VRS-TS2AD201J
VRS-TS2AD333J
VRS-TS2AD000J
VRS-TS2AD471J
VRS-TS2AD471J
VRS-TS2AD333J
VRS-TS2AD333J
VRS-TS2AD223J
VRS-TS2AD103J
VRS-TS2AD333J
VRS-TS2AD333J
VRS-TS2AD333J
VRS-TS2AD333J
VRS-TS2AD512J
VRS-TS2AD102J
VRS-TS2AD000J
VRS-TS2AD105J
VRS-TS2AD103J
VRS-TS2AD121J
VRS-TS2AD222J
AA
AA
AB
AB
AB
AD
AF
AB
AD
AF
AA
AD
AA
AB
AB
AB
AD
AB
AD
AF
BD
AQ
BD
AC
BM
BM
AG
AE
AE
AF
AF
AF
AF
AF
AF
AF
AF
AF
AF
AG
AB
AB
AA
AA
AA
AA
AA
AA
AG
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AG
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
C
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Connector(7pin)
Conector(2pin)
Connector(2pin)
Connector(2pin)
Connector(12pin)
Connector(6pin)
Connector(16pin)
Connector(8pin)
Connector(2pin)
Connector(16pin)
Resistor(1W 100Ω ±5%)
Diode(1SS355)
Diode(1SS355)
Diode(1SS355)
Diode(HRW0202B)
Diode(1SS355)
IC protector(KAB2402)
IC(TC7WT74)
IC(FC200)(Within IC2 and IC4 pair)
IC(W24258S-70LE)
IC(FM209)(Within IC2 and IC4 pair)
IC socket(32pin)
IC,EPROM(1MB)
IC,EPROM(1MB)
IC(NJM2113M)
IC(ULN2003ANS)
IC(XC61AN4502ML)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Coil(HM601)
Photo transistor(SG206S)
Transistor(2SA1037KS)
Transistor(2SA1037KS)
Resistor(1/10W 270Ω ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 10MΩ ±5%)
Resistor(1/10W 3.0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 200Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 470Ω ±5%)
Resistor(1/10W 470Ω ±5%)
Resistor(1/10W 270Ω ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 22KΩ ±5%)
Resistor(1/10W 150Ω ±5%)
Resistor(1/10W 470Ω ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 200Ω ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 470Ω ±5%)
Resistor(1/10W 470Ω ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 22KΩ ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 5.1KΩ ±5%)
Resistor(1/10W 1KΩ ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 1.0MΩ ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 120Ω ±5%)
Resistor(1/10W 2.2KΩ ±5%)
–8–
[C172]
[C173]
[CNCIS]
[CNCSW]
[CNDR]
[CNFRS][40/50]
[CNLIUA]
[CNMT]
[CNPN]
[CNPW]
[CNSP]
[CNTH]
[D1]
[D100]
[D101]
[D102]
[D103]
[D104]
[FU100]
[IC1]
[IC2]
[IC3]
[IC4]
[IC5]
[IC5][8/5]
[IC5][40/50]
[IC6]
[IC8]
[IC101]
[L1]
[L3]
[L4]
[L100]
[L101]
[L102]
[L103]
[L104]
[L105]
[L106]
[PI2]
[Q100]
[Q104]
[R4]
[R6]
[R8]
[R12]
[R14]
[R17]
[R100]
[R101]
[R102]
[R103]
[R104]
[R105]
[R106]
[R107]
[R108]
[R109]
[R110]
[R111]
[R112]
[R113]
[R114]
[R115]
[R117]
[R119]
[R120]
[R121]
[R122]
[R123]
[R124]
[R125]
[R126]
[R128]
[R129]
[R130]
[R131]
[R132]
[R133]
[R134]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[7] Control PWB unit
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
901
VRS-TS2AD333J
VRS-TS2AD000J
VRS-TS2AD000J
VRS-TS2AD224J
VRS-TS2AD153J
VRS-TS2AD203J
VRS-TS2AD303J
VRS-TS2AD433J
VRS-TS2AD103J
VRS-TS2AD102J
VRS-TS2AD000J
VRS-TS2AD000J
VRS-TS2AD000J
VRS-TS2AD334J
VRS-TS2AD104J
VRS-TS2AD104J
VRS-TS2AD102J
VRS-TS2AD203J
VRS-TS2AD512J
VRS-TS2AD562J
VRS-TS2AD474J
VRS-TS2AD203J
VRS-TS2AD104J
VRS-TS2AD271J
VRS-TS2AD103J
VRS-TS2AD471J
VRS-TS2AD000J
RR-TZ3018SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3018SCZZ
RR-TZ3018SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3018SCZZ
RR-TZ3017SCZZ
RR-TZ3018SCZZ
RR-TZ3018SCZZ
RR-TZ3018SCZZ
RR-TZ3018SCZZ
VHI62FP332P-1
RRLYD3138XHZZ
RCRSQ2157SCZZ
RCRSB0297AFZZ
(Unit)
DCEKC689MXHZZ
DCEKC685MXHZZ
DCEKC780MXHZZ
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AF
AG
AF
AD
BP
BP
BP
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
Resistor(1/10W 33KΩ ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 220KΩ ±5%)
Resistor(1/10W 15KΩ ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 30KΩ ±5%)
Resistor(1/10W 43KΩ ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 1KΩ ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 330KΩ ±5%)
Resistor(1/10W 100KΩ ±5%)
Resistor(1/10W 100KΩ ±5%)
Resistor(1/10W 1KΩ ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 5.1KΩ ±5%)
Resistor(1/10W 5.6KΩ ±5%)
Resistor(1/10W 470KΩ ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 100KΩ ±5%)
Resistor(1/10W 270Ω ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 470Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Block resistor(470Ωx4)
Block resistor(270Ωx4)
Block resistor(270Ωx4)
Block resistor(470Ωx4)
Block resistor(470Ωx4)
Block resistor(270Ωx4)
Block resistor(270Ωx4)
Block resistor(470Ωx4)
Block resistor(270Ωx4)
Block resistor(470Ωx4)
Block resistor(470Ωx4)
Block resistor(470Ωx4)
Block resistor(470Ωx4)
IC(XC62FP3302P)
Relay(DQ24D1)
Crystal(32.256MHz)
Crystal(32.768kHz)
E
E
E
Control PWB unit(Within ROM)
Control PWB unit(Within ROM)
Control PWB unit(Within ROM)
[8]
[40/50]
[5]
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
Varistor(RA-391P-V6-2)
Cable
Capacitor(250WV 0.82µF)
Capacitor(50WV 22µF)
Capacitor(50WV 22µF)
Capacitor(50WV 10µF)
Capacitor(50WV 4.7µF)
Capacitor(50WV 22µF)
Capacitor(50WV 22µF)
Capacitor(50WV 22µF)
Capacitor(50WV 2200PF)
Capacitor(50WV 2200PF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 3900PF)
Capacitor(50WV 220PF)
Capacitor(50WV 2200PF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 33PF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 820PF)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Relay
Jack
[AR1]
[ARG]
[C3]
[C5]
[C6]
[C7]
[C9]
[C11]
[C12]
[C13]
[C104]
[C105]
[C106]
[C107]
[C108]
[C109]
[C111]
[C112]
[C113]
[C114]
[C115]
[C117]
[C118]
[C120]
[C122]
[C124]
[C127]
[CML1]
[CNHJ]
[R135]
[R136]
[R138]
[R139]
[R140]
[R141]
[R142]
[R143]
[R144]
[R145]
[R146]
[R148]
[R152]
[R153]
[R154]
[R155]
[R156]
[R157]
[R158]
[R160]
[R161]
[R162]
[R165]
[R167]
[R168]
[R169]
[R170]
[RA1]
[RA2]
[RA3]
[RA4]
[RA5]
[RA6]
[RA7]
[RA8]
[RA9]
[RA11]
[RA12]
[RA13]
[RA14]
[REG100]
[RY1]
[X1]
[X2]
[8] TEL/Liu PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
VHVRA391PV6-1
QCNW-4753XHZZ
RC-FZ3024SCZZ
VCEAGA1HW226M
VCEAGA1HW226M
VCEAGA1HW106M
VCEAGA1HW475M
VCEAGA1HW226M
VCEAGA1HW226M
VCEAGA1HW226M
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1HB102K
VCKYTV1HB392K
VCKYTV1HB221K
VCKYTV1HB221K
VCKYTV1HF104Z
VCKYTV1HB102K
VCKYTV1HF104Z
VCCCTV1HH330J
VCKYTV1EF104Z
VCKYTV1HF104Z
VCKYTV1HB821K
VRS-TS2AD000J
VRS-TS2AD000J
VRS-TS2AD000J
RRLYZ3433XHZZ
QJAKZ2079XH0D
AE
AE
AG
AB
AB
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AG
AD
–9–
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[8] TEL/Liu PWB unit
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
901
QCNCM2548SC1B
QJAKZ2060SC0B
QJAKZ2060SC0B
VHDDSS133//-1
VHDDSS133//-1
QSW-Z2263XHZZ
VHINJM2904M-2
VHINJM2904M-2
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
VHPTLP521-1BL
VS2SC2412KR-1
VSRNC1402//-1
VSRNC1402//-1
VRD-HT2HY223J
VRS-TS2AD433J
VRS-TS2AD152J
VRS-TS2AD102J
VRS-TS2AD512J
VRS-TS2AD203J
VRS-TS2AD000J
VRS-TS2AD203J
VRS-TS2AD433J
VRSTS2AD8662F
VRS-TS2AD332J
VRS-TS2AD101J
VRS-TS2AD151J
VRS-TS2AD332J
VRS-TS2AD224J
VRS-TS2AD683J
VRS-TS2AD822J
VRS-TS2AD621J
VRS-TS2AD000J
VRS-TS2AD332J
VRS-TS2AD000J
VRS-TS2AD513J
VRS-TS2AD203J
VRS-TS2AD102J
VRS-TS2AD203J
VRS-TS2AD473J
VRS-TS2AD332J
VRS-TS2AD473J
VRS-TS2AD472J
RTRNI2164XHZZ
VHVERZV5D471/
VHVERZV5D471/
VHEHZ27-1//-1
(Unit)
DCEKL483BXH02
AH
AD
AD
AA
AA
AG
AG
AG
AC
AC
AC
AC
AC
AE
AD
AC
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AG
AC
AC
AB
C
C
C
B
B
B
B
B
C
C
C
C
C
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
Connector(12pin)
Jack
Jack
Diode(1SS133)
Diode(1SS133)
Hook switch
IC(NJM2904M)
IC(NJM2904M)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Photo coupler(TLP521)
Transistor(2SC2412K)
Transistor(RNC1402)
Transistor(RNC1402)
Resistor(1/2W 22KΩ ±5%)
Resistor(1/10W 43KΩ ±5%)
Resistor(1/10W 1.5KΩ ±5%)
Resistor(1/10W 1KΩ ±5%)
Resistor(1/10W 5.1KΩ ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 43KΩ ±5%)
Resistor(1/10W 86.6KΩ ±1%)
Resistor(1/10W 3.3KΩ ±5%)
Resistor(1/10W 100Ω ±5%)
Resistor(1/10W 150Ω ±5%)
Resistor(1/10W 3.3KΩ ±5%)
Resistor(1/10W 220KΩ ±5%)
Resistor(1/10W 68KΩ ±5%)
Resistor(1/10W 8.2KΩ ±5%)
Resistor(1/10W 620Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 3.3KΩ ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/10W 51KΩ ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 1KΩ ±5%)
Resistor(1/10W 20KΩ ±5%)
Resistor(1/10W 47KΩ ±5%)
Resistor(1/10W 3.3KΩ ±5%)
Resistor(1/10W 47KΩ ±5%)
Resistor(1/10W 4.7KΩ ±5%)
Transformer
Varistor(ERZV5D471)
Varistor(ERZV5D471)
Zener diode(HZ27)
AX
E
TEL/Liu PWB unit
AF
AN
AD
AC
AB
AF
AH
AF
AK
AC
AF
AF
AC
AC
AC
AC
AD
AD
AD
AD
AD
AD
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
Capacitor(RE224-C)
Capacitor(KMF400VB68M)
Capacitor(ECKZ3D102KBP)
Capacitor(GRM40B222K50PT)
Resistor(MCR10EZHJ000)
Capacitor(DE1510-1E392M-KX)
Capacitor(LXJ35VB560(M))
Capacitor(ECQV1H474JL3)
Capacitor(LXZ16VB2200(K))
Capacitor(GRM40B104K25PT)
Capacitor(DE1007E222M-KH)
Capacitor(KME10VB100(M))
Capacitor(GRM40B102K50PT)
Capacitor(DEO805R681K1K-MHR)
Capacitor(AMZV-223J50)
Base post ass’y(B 2P3-VH)
Connector(8PL-FJ)
Diode(ERA15-06)
Diode(ERA15-06)
Diode(ERA15-06)
Diode(ERA15-06)
Diode(1SS355)
[CNLIUA]
[CNLNJ]
[CNTLJ]
[D1]
[D4]
[HOOK SW]
[IC101]
[IC102]
[L3A]
[L3B]
[L6]
[L7]
[L8]
[PC5]
[Q101]
[Q104]
[Q107]
[R3]
[R101]
[R108]
[R109]
[R110]
[R111]
[R112]
[R113]
[R114]
[R115]
[R116]
[R118]
[R123]
[R125]
[R126]
[R127]
[R128]
[R129]
[R130]
[R131]
[R132]
[R133]
[R134]
[R135]
[R140]
[R141]
[R142]
[R143]
[R144]
[T1]
[VA1]
[VA2]
[ZD4]
[9] Power supply PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
0CBUGFM224KR/
0CBUGZ1072ZZ/
0CBUGCV102HZ/
0CBUGXAEF222/
0CBUEXCAO000/
0CBUGCM392BJ/
0CBUGAE561TS/
0CBUGFF474JA/
0CBUGAC222VV/
0CBUGXAED104/
0CBUGZ1041ZZ/
0CBUGAB101RV/
0CBUGXAEF102/
0CBUGCU681BR/
0CBUGFF223EH/
0CBPKZ0194ZZ/
0CBPCZ0275ZZ/
0CBUBC0125DK/
0CBUBC0125DK/
0CBUBC0125DK/
0CBUBC0125DK/
0CBUBY0020AK/
– 10 –
[C1]
[C2]
[C3]
[C4]
[C6]
[C7]
[C8]
[C9]
[C10]
[C12]
[C15]
[C16]
[C17]
[C21]
[C24]
[CN1]
[CN2]
[D1]
[D2]
[D3]
[D4]
[D5]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[9] Power supply PWB unit
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
!
901
0CBUBC0336AZ/
0CBUBC0302BZ/
0CBPJCEJ1601/
0CBPJCEJ1601/
0CBPZZ0906ZZ/
0CBBFZ89256Z/
0CBUCB0199AZ/
0CBUKZ0826ZZ/
0CBUZZ0156ZZ/
0CBPZZ0940ZZ/
0CBLRZ6616ZN/
0CBLRZ6619ZQ/
0CBUDC0163CZ/
0CBUDC0163CZ/
0CBUAG0161AC/
0CBUDA0128AK/
0CBUAY0016CK/
0CBUAY0016CK/
0CBUAC0289AK/
0CBUAC0289AK/
0CBUEEC335CH/
0CBUEEC105CH/
0CBUEEC105CH/
0CBUEXCAS331/
0CBUEXCAS152/
0CBUEXCAS183/
0CBUEXCAS330/
0CBUEXCAS473/
0CBUEXCAS471/
0CBUEFDR33DB/
0CBUEXCAS390/
0CBUEXCAS184/
0CBUEXCAS472/
0CBUEXCAS152/
0CBUEXCAS334/
0CBUEXCAS223/
0CBUEXCAS822/
0CBUEXCAS273/
0CBUEXCAS472/
0CBUEXCAS472/
0CBUEXCAS154/
0CBUEXCAS103/
0CB829655027/
0CBUDC0232AK/
0CBUEZ0507ZZ/
0CBUFBA102FE/
0CBUBDAX270A/
0CBUBXAD2R0A/
0CBUBDBM300D/
0CBUBXAD6R2C/
0CBUBDBE200D/
(Unit)
RDENT2144XHZZ
AL
AE
AH
AH
AH
AD
AR
AK
AN
AB
AQ
AQ
AG
AG
AQ
AD
AD
AD
AD
AD
AC
AC
AC
AB
AB
AB
AB
AB
AB
AE
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
BE
AF
AD
AD
AD
AD
AC
AD
AD
B
B
A
A
A
B
B
C
C
C
C
C
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
Diode(S3L20U-4004P15)
Diode(SR140)
Current fuse(21501.6 ME600)
Current fuse(21501.6 ME600)
Circuit protect chip(CCP2E100)
Beads core(BL02RNI-R62T4)
IC(UPC29M05AHF)
Filter(ELF15N003A)
Coil(RS208)
Jumper(J1/6Z-T26-A)
Heat sink(MN903-5001AT)
Heat sink(MF903-5002AT)
Photo coupler(PC123YS)
Photo coupler(PC123YS)
FET(FS5KM-18A-AN)
Transistor(2SD2114K)
Transistor(2SC2412K)
Transistor(2SC2412K)
Transistor(2SC4210)
Transistor(2SC4210)
Resistor(RDM12TB335J)
Resistor(RDM12TB105J)
Resistor(RDM12TB105J)
Resistor(CR21TR331J)
Resistor(CR21TR152J)
Resistor(CR21TR183J)
Resistor(CR21TR330J)
Resistor(CR21TR473J)
Resistor(CR21TR471J)
Resistor(RSMF1TBR33G)
Resistor(CR21TR390J)
Resistor(CR21TR184J)
Resistor(CR21TR472J)
Resistor(CR21TR152J)
Resistor(CR21TR334J)
Resistor(CR21TR223J)
Resistor(CR21TR822J)
Resistor(CR21TR273J)
Resistor(CR21TR472J)
Resistor(CR21TR472J)
Resistor(CR21TR154J)
Resistor(CR21TR103J)
Transformer(PTTP124-KTT)
Thermistor(KL07L8R2TB)
Varistor(ERZV07D471)
Variable resistor(ENV CYA A01 B13)
Zener diode(RD27SB)
Zener diode(RD2.0SB)
Zener diode(RD30FB)
Zener diode(RD6.2SB)
Zener diode(RD20ESAB)
BA
E
Power supply PWB unit
– 11 –
[D7]
[D8]
[F1]
[F2]
[F3]
[FB1]
[IC1]
[L1]
[L2]
[L3]
[MT1]
[MT2]
[PC1]
[PC2]
[Q1]
[Q2]
[Q3]
[Q4]
[Q5]
[Q6]
[R1]
[R2]
[R3]
[R4]
[R5]
[R6]
[R7]
[R8]
[R9]
[R10]
[R11]
[R12]
[R13]
[R14]
[R15]
[R16]
[R17]
[R18]
[R19]
[R20]
[R21]
[R25]
[T1]
[TH1]
[V1]
[VR1]
[ZD1]
[ZD2]
[ZD4]
[ZD5]
[ZD7]
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
Index
PARTS CODE
[C]
CCNW-212AXH01
″
CCNW-215AXH01
[D]
DCEKC685MXHZZ
″
DCEKC689MXHZZ
″
DCEKC780MXHZZ
″
DCEKL483BXH02
″
DCEKP481BXH04
″
DCEKP481BXH05
″
DCEKP481BXH18
″
DCEKP481BXH19
″
DCEKP482BXH01
DCEKP482BXH02
DUNTK468BXHPU
[G]
GCABA2342XHSA
GCABA2342XHSB
GCABA2342XHSC
GCABB2343XHSA
GCABB2343XHSB
GCABB2343XHSC
GCASP2110XHSD
GCASP2110XHSE
GCASP2110XHSF
GCASP2111XHSA
GCASP2111XHSB
GCASP2111XHSC
GDAI-2082XHSD
GDAI-2083XHZZ
[H]
HPNLH2392XHSU
HPNLH2392XHS3
HPNLH2394XHSA
HPNLH2394XHSE
[J]
JBTN-2257XHSD
JBTN-2258XHSA
JBTN-2258XHSB
JBTN-2258XHSC
JBTN-2261XHSA
JBTN-2261XHSC
[L]
LBNDJ2006XHZZ
″
LBSHP2110XHZZ
LBSHP2112XHZZ
LFRM-2207XHZZ
LFRM-2208XHZZ
LFRM-2209XHZZ
LHLDZ2180XHZZ
LHLDZ2181XHZZ
LHLDZ2184XHZZ
LHLDZ2185XHZZ
LPLTG2911XHZZ
LPLTM3049XHZZ
LPLTP2908XHZZ
LPLTP3051XHZZ
LPLTP3058XHZZ
LSTPP2054XHZZ
LX-BZ2138XHZZ
[M]
MCAMP2027XHZZ
MLEVP2311XHZZ
MLEVP2312XHZZ
MLEVP2314XHZZ
MLEVP2316XHZZ
MLEVP2317XHZZ
MLEVP2319XHZZ
MLEVP2320XHZZ
MLEVP2321XHZZ
No.
PRICE NEW PART
RANK MARK RANK
1-2
3-1
1-12
AK
AK
AG
1-45
7-901
1-45
7-901
1-45
7-901
1-16
8-901
1-1
3-901
1-1
3-901
1-1
3-901
1-1
3-901
3-7
3-7
6-2
BP
BP
BP
BP
BP
BP
AX
AX
AP
AP
AP
AP
AP
AP
AP
AP
AQ
AP
AH
3-3
3-3
3-3
1-13
1-13
1-13
1-17
1-17
1-17
1-18
1-18
1-18
1-46
1-22
AH
AH
AH
AK
AK
AK
AK
AK
AK
AH
AH
AH
AD
AF
1-54
1-54
1-54
1-54
AE
AE
AE
AE
3-4
3-5
3-5
3-5
3-6
3-6
AD
AC
AC
AC
AC
AC
1-55
2-19
2-1
1-28
5-1
1-29
2-2
2-3
2-4
1-30
1-31
4-1
5-2
4-2
4-3
4-8
1-47
1-B1
AA
AA
AB
AB
AF
AF
AF
AC
AC
AC
AC
AE
AD
AE
AB
AD
AC
AB
5-4
5-5
5-6
5-8
1-23
2-5
1-49
1-19
1-58
AC
AB
AB
AB
AC
AB
AC
AC
AN
C
C
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
D
D
D
D
D
D
C
C
C
C
C
C
C
C
D
D
D
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
MSPRC2735XHZZ
MSPRC2954XHZZ
MSPRC3110XHZZ
MSPRC3112XHZZ
MSPRC3117XHZZ
MSPRC3148XHZZ
MSPRD3116XHZZ
MSPRP3119XHZZ
MSPRP3123XHZZ
MSPRT3139XHZZ
MSPRT3140XHZZ
[N]
NGERH2278XHZZ
NGERH2379XHZZ
NGERH2391XHZZ
NGERH2475XHZZ
NGERH2478XHZZ
NGERH2479XHZZ
NGERH2480XHZZ
NGERH2481XHZZ
NGERP2318XHZZ
NROLR2375XHZZ
NROLR2425XHZZ
NROLR2428XHZZ
NSFTZ2273XHZZ
NSFTZ2320XHZZ
[P]
PGIDM2554XHZZ
PGIDM2560XHSD
PGIDM2561XHSD
PGIDM2562XHZA
PGIDM2562XHZZ
PGIDM2563XHSA
PGIDM2563XHSB
PGIDM2563XHSC
PGIDM2566XHZZ
PGIDM2578XHZZ
PGIDM2579XHZZ
PHOP-2104XHSD
PHOP-2105XHZZ
PSHEZ3410XHZZ
PSHEZ3436XHZZ
PSHEZ3517XHZZ
[Q]
QACCE2042XHZZ
QCNCM2401SC0B
QCNCM2442SC0B
QCNCM2548SC1B
QCNCM7014SC0B
QCNCM7014SC0F
QCNCM7014SC0G
QCNCM7014SC1F
″
QCNCM705BAF06
QCNCW2500SC0H
QCNCW2500SC1B
QCNW-209AXHZZ
QCNW-210AXHZZ
QCNW-211AXHZZ
QCNW-213AXHZZ
QCNW-3975XHGY
QCNW-3976XHBG
QCNW-3976XHOG
QCNW-3976XHOW
QCNW-4753XHZZ
QCNW-4933XHZZ
QFS-P2010SCZZ
QJAKZ2060SC0B
″
QJAKZ2079XH0D
QSOCZ2051SC32
QSW-F2224SCZZ
QSW-M2293XHZZ
QSW-M2296XHZZ
QSW-Z2263XHZZ
[R]
RC-FZ3024SCZZ
RCILZ2145XHZZ
″
″
No.
PRICE NEW PART
RANK MARK RANK
5-9
1-5
5-10
1-33
2-6
1-34
1-24
1-14
1-15
4-5
4-4
AC
AC
AB
AC
AB
AC
AB
AC
AC
AA
AA
C
C
C
C
C
C
C
C
C
C
C
5-12
5-13
5-15
5-17
1-36
2-7
2-8
2-9
1-6
2-10
1-37
2-11
2-12
6-18
AC
AC
AC
AB
AB
AB
AB
AB
AD
AL
AP
AP
AF
AF
C
C
C
C
C
C
C
C
C
C
C
C
C
C
4-6
1-7
1-8
2-13
2-13
1-27
1-27
1-27
1-52
6-16
6-17
1-9
6-4
1-56
2-14
4-7
AF
AE
AC
AD
AD
AE
AE
AC
AC
AE
AE
AF
AD
AB
AC
AE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1-20
7-91
7-84
8-30
7-86
7-88
7-83
7-89
7-92
7-85
7-90
7-87
1-39
1-40
2-15
2-16
6-5
6-3
6-3
6-3
8-2
5-20
7-99
8-31
8-32
8-29
7-104
5-21
2-17
1-11
8-35
AL
AA
AB
AH
AD
AB
AB
AD
AD
AB
AF
AF
AH
AC
AF
AC
AG
AK
AT
AK
AE
AC
AD
AD
AD
AD
AC
AE
AE
AD
AG
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
B
B
B
B
8-3
7-61
7-64
7-109
AG
AF
AF
AF
C
C
C
C
– 12 –
N
N
N
N
N
PRICE NEW PART
RANK MARK RANK
PARTS CODE
No.
RCILZ2145XHZZ
″
″
″
″
″
″
″
″
RCORF2123XHZZ
RCORF2125XHZZ
RCRSB0297AFZZ
RCRSQ2157SCZZ
RDENT2144XHZZ
″
RFILN2027XHZZ
″
″
″
″
RHEDZ2059XHZZ
RMOTZ2148XHZZ
RR-TZ3017SCZZ
″
″
″
″
RR-TZ3018SCZZ
″
″
″
″
″
″
″
RRLYD3138XHZZ
RRLYZ3433XHZZ
RTRNI2164XHZZ
RUNTZ2054XHZZ
[S]
SPAKA287BXHZZ
SPAKA288BXHZZ
SPAKA289BXHZZ
SPAKA388BXHZZ
SPAKA389BXHZZ
SPAKC178BXHZZ
SPAKC187BXHZZ
SPAKC189BXHZZ
SPAKC194BXHZZ
SPAKP296BXHZZ
[T]
TCADZ2935XHZZ
TINST4026XHZZ
TLABM341AXHZZ
TLABM344AXHZZ
TLABM345AXHZZ
TLABM347AXHZZ
[U]
UBATL2046SCZZ
[V]
VCCCTV1HH120J
″
VCCCTV1HH220J
″
″
″
″
″
″
″
″
VCCCTV1HH330J
VCEAGA1EW476M
″
″
VCEAGA1HW106M
″
″
″
VCEAGA1HW226M
7-110
7-111
7-112
7-113
7-114
7-115
7-116
7-117
7-118
2-20
1-53
7-203
7-202
1-21
9-901
8-38
8-39
8-40
8-41
8-42
1-41
5-22
7-188
7-189
7-192
7-193
7-195
7-187
7-190
7-191
7-194
7-196
7-197
7-198
7-199
7-201
8-28
8-76
2-18
AF
AF
AF
AF
AF
AF
AF
AF
AF
AD
AE
AD
AF
BA
BA
AC
AC
AC
AC
AC
BF
AT
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AG
AG
AG
BE
6-7
6-8
6-9
6-21
6-22
6-10
6-10
6-10
6-10
6-6
AE
AE
AC
AE
AE
AH
AH
AH
AH
AE
6-19
6-1
6-11
6-11
6-11
6-11
AA
AY
AD
AD
AD
AD
7-1
AK
B
7-19
7-20
7-33
7-34
7-42
7-43
7-55
7-56
7-58
7-59
7-66
8-21
7-10
7-11
7-14
7-6
7-8
7-12
8-6
7-13
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
B
B
B
B
E
E
C
C
C
C
C
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
PARTS CODE
VCEAGA1HW226M
″
″
″
″
VCEAGA1HW475M
VCKYTV1CF105Z
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VCKYTV1EB104K
″
VCKYTV1EF104Z
″
″
″
″
″
″
″
″
″
″
″
″
″
VCKYTV1HB102K
″
″
″
″
″
″
″
″
″
″
″
VCKYTV1HB103K
″
VCKYTV1HB221K
″
″
VCKYTV1HB222K
″
″
″
″
″
″
VCKYTV1HB392K
VCKYTV1HB472K
VCKYTV1HB821K
VCKYTV1HF104Z
″
″
″
″
VHDDSS133//-1
″
VHDHRW0202B-1
VHD1SS355//-1
No.
8-4
8-5
8-8
8-9
8-10
8-7
7-17
7-21
7-24
7-29
7-30
7-32
7-38
7-39
7-40
7-41
7-44
7-49
7-50
7-51
7-53
7-57
7-62
7-63
7-65
7-71
7-76
7-77
7-47
7-68
7-4
7-7
7-28
7-31
7-35
7-37
7-46
7-48
7-54
7-74
7-78
7-80
8-13
8-22
7-2
7-3
7-15
7-16
7-22
7-23
7-25
7-45
7-81
7-82
8-14
8-19
7-5
7-73
7-72
8-16
8-17
7-26
7-27
7-36
7-52
7-60
8-11
8-12
8-15
7-75
8-24
7-18
7-79
8-18
8-20
8-23
8-33
8-34
7-97
7-94
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
AB
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AB
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
PARTS CODE
No.
VHD1SS355//-1
″
″
VHEHZ27-1//-1
VHIFC2FM209-1
″
VHINJM2113M-1
VHINJM2904M-2
″
VHITC7WT74FU1
VHIULN2003AN/
VHIW24258S7LE
VHIXC61AN45M1
VHI27010FZJ0B
VHI27010FZK0A
VHI62FP332P-1
VHPSG206S//-1
VHPTLP521-1BL
VHVERZV5D471/
″
VHVRA391PV6-1
VRD-HT2HY223J
VRS-HT3AA101J
VRS-TS2AD000J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TS2AD101J
VRS-TS2AD102J
″
″
″
″
VRS-TS2AD103J
″
″
″
″
VRS-TS2AD104J
″
″
VRS-TS2AD105J
VRS-TS2AD106J
VRS-TS2AD121J
VRS-TS2AD151J
″
VRS-TS2AD152J
VRS-TS2AD153J
VRS-TS2AD201J
″
VRS-TS2AD203J
″
″
″
″
″
″
VRS-TS2AD222J
VRS-TS2AD223J
″
VRS-TS2AD224J
″
VRS-TS2AD271J
″
7-95
7-96
7-98
8-79
7-101
7-103
7-106
8-36
8-37
7-100
7-107
7-102
7-108
7-104
7-104
7-200
7-119
8-43
8-77
8-78
8-1
8-47
7-93
7-9
7-67
7-69
7-70
7-127
7-129
7-142
7-155
7-161
7-162
7-170
7-171
7-172
7-186
8-25
8-26
8-27
8-53
8-65
8-67
8-58
7-154
7-169
7-176
8-50
8-70
7-124
7-148
7-157
7-168
7-184
7-174
7-175
7-182
7-156
7-125
7-158
7-137
8-59
8-49
7-164
7-128
7-140
7-165
7-177
7-181
8-52
8-54
8-69
8-71
7-159
7-136
7-147
7-163
8-61
7-122
7-132
– 13 –
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
BD
BD
AG
AG
AG
AF
AE
AQ
AE
BM
BM
AF
AG
AE
AC
AC
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AG
AG
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
N
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PRICE NEW PART
RANK MARK RANK
PARTS CODE
No.
VRS-TS2AD271J
VRS-TS2AD3R0J
VRS-TS2AD303J
VRS-TS2AD332J
″
″
″
VRS-TS2AD333J
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TS2AD334J
VRS-TS2AD433J
″
″
VRS-TS2AD471J
″
″
″
″
″
VRS-TS2AD472J
VRS-TS2AD473J
″
VRS-TS2AD474J
VRS-TS2AD512J
″
″
VRS-TS2AD513J
VRS-TS2AD562J
VRS-TS2AD621J
VRS-TS2AD683J
VRS-TS2AD822J
VRSTS2AD8662F
VSRNC1402//-1
″
VS2SA1037KS-1
″
VS2SC2412KR-1
[X]
XBBSD30P06000
XBPSN40P06K00
XEBSD30P08000
″
XEBSD30P12000
XUBSD20P06000
[0]
0CBBFZ89256Z/
0CBLRZ6616ZN/
0CBLRZ6619ZQ/
0CBPCZ0275ZZ/
0CBPJCEJ1601/
″
0CBPKZ0194ZZ/
0CBPZZ0906ZZ/
0CBPZZ0940ZZ/
0CBUAC0289AK/
″
0CBUAG0161AC/
0CBUAY0016CK/
″
0CBUBC0125DK/
″
″
″
0CBUBC0302BZ/
0CBUBC0336AZ/
0CBUBDAX270A/
0CBUBDBE200D/
0CBUBDBM300D/
0CBUBXAD2R0A/
7-183
7-126
7-166
8-57
8-60
8-66
8-73
7-123
7-133
7-134
7-135
7-139
7-141
7-145
7-146
7-149
7-150
7-151
7-152
7-160
7-173
7-167
8-48
8-55
7-130
7-131
7-138
7-143
7-144
7-185
8-75
8-72
8-74
7-180
7-153
7-178
8-51
8-68
7-179
8-64
8-62
8-63
8-56
8-45
8-46
7-120
7-121
8-44
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AB
AB
AD
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
1-B4
1-B5
1-B3
5-B3
1-B7
3-B2
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
9-28
9-33
9-34
9-17
9-25
9-26
9-16
9-27
9-32
9-41
9-42
9-37
9-39
9-40
9-18
9-19
9-20
9-21
9-24
9-23
9-69
9-73
9-71
9-70
AD
AQ
AQ
AD
AH
AH
AC
AH
AB
AD
AD
AQ
AD
AD
AD
AD
AD
AD
AE
AL
AD
AD
AC
AD
B
C
C
C
A
A
C
A
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
PARTS CODE
0CBUBXAD6R2C/
0CBUBY0020AK/
0CBUCB0199AZ/
0CBUDA0128AK/
0CBUDC0163CZ/
″
0CBUDC0232AK/
0CBUEEC105CH/
″
0CBUEEC335CH/
0CBUEFDR33DB/
0CBUEXCAO000/
0CBUEXCAS103/
0CBUEXCAS152/
″
0CBUEXCAS154/
0CBUEXCAS183/
0CBUEXCAS184/
0CBUEXCAS223/
0CBUEXCAS273/
0CBUEXCAS330/
0CBUEXCAS331/
0CBUEXCAS334/
0CBUEXCAS390/
0CBUEXCAS471/
0CBUEXCAS472/
″
″
0CBUEXCAS473/
0CBUEXCAS822/
0CBUEZ0507ZZ/
0CBUFBA102FE/
0CBUGAB101RV/
0CBUGAC222VV/
0CBUGAE561TS/
0CBUGCM392BJ/
0CBUGCU681BR/
0CBUGCV102HZ/
0CBUGFF223EH/
0CBUGFF474JA/
0CBUGFM224KR/
0CBUGXAED104/
0CBUGXAEF102/
0CBUGXAEF222/
0CBUGZ1041ZZ/
0CBUGZ1072ZZ/
0CBUKZ0826ZZ/
0CBUZZ0156ZZ/
0CB829655027/
No.
9-72
9-22
9-29
9-38
9-35
9-36
9-66
9-44
9-45
9-43
9-52
9-5
9-64
9-47
9-56
9-63
9-48
9-54
9-58
9-60
9-49
9-46
9-57
9-53
9-51
9-55
9-61
9-62
9-50
9-59
9-67
9-68
9-12
9-9
9-7
9-6
9-14
9-3
9-15
9-8
9-1
9-10
9-13
9-4
9-11
9-2
9-30
9-31
9-65
PRICE NEW PART
RANK MARK RANK
AD
AD
AR
AD
AG
AG
AF
AC
AC
AC
AE
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AD
AD
AF
AK
AH
AF
AC
AD
AC
AF
AF
AC
AC
AC
AF
AN
AK
AN
BE
PARTS CODE
No.
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
– 14 –
PRICE NEW PART
RANK MARK RANK
PARTS CODE
No.
PRICE NEW PART
RANK MARK RANK
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
COPYRIGHT © 1999 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
9911-37NS•IS•T