Yamaha YST-MS30 Owner`s manual

BG
POWERED MULTIMEDIA SPEAKERS
YST-MS30
OWNER’S MANUAL . . . . . . . . . . . . 2
MODE D’EMPLOI . . . . . . . . . . . . . . 4
BEDIENUNGSANLEITUNG. . . . . . . 6
BRUKSANVISNING. . . . . . . . . . . . . 8
MANUALE DI ISTRUZIONI . . . . . . 10
MANUAL DE INSTRUCCIONES . . 12
GEBRUIKSAANWIJZING . . . . . . . 14
E
M
U
L
O
V
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
Special Instructions for U.K. Model
IMPORTANT
THE WIRE IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or
coloured RED. Making sure that neither core is connected to
the earth terminal of the three pin plug.
ii
OBSERVERA
Apparaten kopplas inte bort från växelströmskällan (nätet)
så länge som den är ansluten till vägguttaget, även om
själva apparaten har stängts av.
ADVARSEL
Netspæendingen til dette apparat er IKKE afbrudt,
sålæenge netledningen siddr i en stikkontakt, som er t endt
– også selvom der or slukket på apparatets afbryder.
VAROITUS
Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.
Connection / Connexion / Anschlüsse / Anslutningar / Collegamento /
Conexión / Aansluitingen
1
3.5 mm stereo mini plug cable
2
AC adapter
TO RIGHT
SPEAKER
1
INPUT
2
INPUT
TO LEFT
SPEAKER
0
10
BASS
LEFT
SATELLITE
SPEAKER
DC 15V
RIGHT
SATELLITE
SPEAKER
SUBWOOFER
1 3.5 mm stereo mini plug cable × 1 (Accessory) / Câble avec fiches mini-jack stéréo 3,5 mm × 1 (Accessoire) /
3,5 mm Stereo-Miniklinkenkabel × 1 (Lieferumfang) / Kabeln med 3,5 mm stereominikontakt × 1 (Tillbehör) /
Cavo con minispina stereo di 3,5 mm × 1 (Accessorio) / Cable con miniclavija estéreo de 3,5 mm × 1 (Accesorio) / 3,5 mm stereo ministekkersnoer × 1 (Accessoire)
2 AC adapter × 1 (Accessory)/ Adaptateur secteur × 1(Accessoire) / Netzteil × 1 (Lieferumfang) / Nätadapter × 1
(Tillbehör) / Trasformatore CA × 1 (Accessorio) / Adaptador de CA × 1 (Accesorio) / Netadapter × 1 (Accessoire)
Controls & Connectors / Commandes et Connecteurs / Bedienelemente
und Anschlüsse / Reglage & Kopplingar / Comandi e Connettori / Controles y Conectores / Bedieningsorganen & Aansluitingen
Subwoofer rear panel
Right satellite speaker top side
VOLUME
TO RIGHT
SPEAKER
1
1
INPUT
2
INPUT
2
TO LEFT
SPEAKER
3
0
10
BASS
4
DC 15V
6
7
5
1
Thank you for purchasing Yamaha’s YST-MS30 Powered Multimedia Speakers. Advanced Yamaha Active Servo
Technology offers exceptionally high performance, allowing these compact speakers to produce a rich bass sound.
Cautions
Please read the following operating precautions before
use:
• When you disconnect the AC adapter from the AC
receptacle, hold the plug, not the cord.
• If you plan not to use the YST-MS30s for a while,
disconnect the AC adapter from the AC receptacle.
• Always disconnect the AC adapter from the AC
receptacle before making any connections.
• The YST-MS30s do not contain any user serviceable parts. Refer all servicing to your Yamaha
dealer.
• Never open the cabinet. If a foreign object drops
into the set, contact your dealer, and do not use the
YST-MS30s. Otherwise, you may cause a fire.
• Do not expose the YST-MS30s to temperature
extremes, direct sunlight, excessive dust, humidity,
or vibration.
• Position the YST-MS30s on a level, stable surface.
Do not drop the YST-MS30s, apply excessive force
to their controls, or put heavy items on top of them.
• Do not place small metal objects on the speakers.
Otherwise, the object may fall, possibly causing an
injury.
• Since this unit has a built-in power amplifier, heat
will radiate from the rear panel. Therefore, place
the unit apart from the walls, allowing a space of at
least 20 cm (7-7/8") above, behind and on the both
sides of the unit. Also, do not position with the rear
panel facing down on the floor or other surface.
(Subwoofer only)
• Do not obstruct the port with your hand or a foreign
object.
• To protect the YST-MS30 speakers, avoid microphone feedback, continuous and excessive output
from electronic musical instruments, and excessive
signal distortion.
• If the YST-MS30s are located close to fluorescent
or neon lights, a slight hum may be heard. In this
case, relocate the YST-MS30s away from the light.
• Although the YST-MS30 speakers are magnetically
shielded, keep floppy disks and tapes away from
them.
• The YST-MS30s may cause picture distortion when
located close to a television or computer monitor. In
this case, move them away a short distance.
• Avoid sources of hum (transformers, motors). To
prevent fire or electrical shock, do not expose to
rain and water.
• Do not use force on switches, knobs, or cables.
When you move the YST-MS30, first turn off the
power to the speakers, then disconnect the AC
adapter from the AC receptacle and the cables from
the connected devices.
2
• Always turn the volume control counterclockwise
to the minimum before starting to play the audio
source: increase the volume gradually to an appropriate level after the playback has started.
Controls & Connectors
Refer to the illustrations on page 1.
1 TO RIGHT SPEAKER
Connect the 8-pin cable from the right satellite
speaker to this connector.
2 INPUT 1/2
You can input two audio sources to the speaker
system from these input jacks. For example, you
can connect the output of a CD-ROM player and a
personal computer here. The two audio sources are
mixed together by the speaker system.
3 TO LEFT SPEAKER
Connect the RCA plug cable from the left satellite
speaker to this connector.
4 BASS control
Allows you to adjust the volume level of the subwoofer.
A typical (recommended) setting is the position
between one o’clock and two o’clock.
Rotating the control clockwise will increase the
volume level, and rotating the control counterclockwise will decrease the level.
5 DC connector
Connect the included AC adapter to this connector.
Press the (standby/on) button on the right satellite speaker to turn the power on or standby.
6 VOLUME control
Allows you to adjust the volume level of the entire
speaker system.
Rotating the control clockwise will increase the
volume level, and rotating the control counterclockwise will decrease the level.
7
(standby/on) button/indicator
Press this button to turn on the power to the
speaker system. Its indicator lights up. Press the
button again to turn the speaker system to standby
mode.
Before turning the power on or standby, make sure
that the VOLUME control setting is lowered. A
small electrical current flows through the speaker
system even if the standby/on switch is turned off.
You can adjust the speaker angle. Loosen the
screw on the bottom of the speaker stand as
shown in the figure, adjust the angle of the
stand, and tighten the screw to fix the stand.
Loosen
English
Speaker angle and Non skid pad
Tighten
Speaker stand
*
*
To prevent the speakers from sliding around,
attach the supplied pads to the four points on the
bottom of each satellite speaker. Place the
speaker on a stable, flat surface.
* Non skid
pad
Specifications
Type .................................. Advanced Yamaha Active
Servo Technology
Output power
Satellite.............................. 6 W + 6 W (1 kHz, 4Ω at
T.H.D.=10%)
Subwoofer ......................... 18 W (100 Hz, 4Ω at
T.H.D.=10%)
Input sensitivity .............. 200 mV (1 kHz, 4Ω at 6 W)
Input impedance ............ 20 kΩ
Frequency response ....... 45 Hz to 20 kHz (Satellite +
Subwoofer)
Crossover Frequency....... Satellite/Subwoofer 180 Hz
Driver
Satellite....................5 cm (2") cone, magnetic shielding
Subwoofer ...............12 cm (5") cone, magnetic shielding
Power supply (AC adapter)
U.S.A. and Canada models .........AC 120 V, 60 Hz
Australia model ...........................AC 240 V, 50 Hz
U.K. and Europe models .............AC 230 V, 50 Hz
Dimensions (W × H × D)
Satellite speakers............... 65 (2.6") × 75 (3") × 119
(4.7") mm
Subwoofer ......................... 183 (7.2") × 196 (7.7") × 183
(7.2") mm
Input Section
Weight
Subwoofer ......................... 3.5 mm stereo mini jack for
audio-signal × 2
Satellite speakers............... Right: 0.45 kg (1 lb.)
Left: 0.36 kg (13 oz.)
Subwoofer ......................... 2.3 kg (5 lbs. 1 oz.)
Output Section
Subwoofer ......................... RCA pin jack connected to
left satellite speaker
8 pin jack connected to right
satellite speaker
Accessories
AC adapter × 1
3.5 mm stereo mini plug cable × 1 (1.8 m)
8 pcs of non skid pads × 1 set
* Specifications subject to change without notice.
Troubleshooting
If the speakers fail to operate normally, check the following table. It lists common operation errors and simple measures that you can take to correct problems. If a problem cannot be corrected, or the symptom is not listed, disconnect the AC adapter and contact your authorized YAMAHA dealer or service center for help.
FAULT
No sound comes
from the speakers
or subwoofer.
CAUSE
CURE
The AC adapter is not properly plugged into Insert the AC adapter firmly into the AC receptathe AC receptacle.
cle.
The
(standby/on) button is turned off.
Turn on the
lights).
(standby/on) button (the indicator
Connections are faulty or incomplete.
Make the connections again, firmly, or use a different cable.
The volume is set to minimum.
Turn the speaker VOLUME control to the right to
increase the volume.
The level of the signal being input is too low. Turn up the volume on the connected component.
The bass sound can The BASS control is set to minimum.
not be heard.
Turn the subwoofer BASS control to the right to
increase the volume.
Sound is distorted.
The level of the signal being input is too high.
Turn down the volume on the connected component.
Noise.
Connections are faulty or incomplete.
Make the connections again, firmly, or use a different cable.
3
Printed in China
IP
V465840