Miele DA 1160 Technical data

Operating and Installation instructions
Rangehood
To avoid the risk of accidents or damage to the appliance, it is essential
to read these instructions before it is installed and used for the first time.
en - AU, NZ
M.-Nr. 09 712 770
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switching the lighting on/off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching the fan on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Charcoal filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Safety distance between cooktop and rangehood. . . . . . . . . . . . . . . . . . . . . . 19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation under a wall unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Fitting the rangehood to the wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.
3
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on the safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This rangehood is designed for
domestic use and for use in similar
environments by guests in hotel or
motel rooms, bed & breakfasts and
other typical living quarters. This does
not include common/shared facilities or
commercial facilities within hotels,
motels or bed & breakfasts.
~ It must only be used to extract
vapours and remove odours from
cooking.
~ Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
appliance.
4
~ This appliance is not suitable for
outdoor use.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been been shown how to use it by a
person responsible for their safety.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions.
~ This appliance is not a toy! To avoid
the risk of injury, keep children well
away and do not allow them to play with
it or to use the controls. They will not
understand the potential dangers
posed by it. They should be supervised
whenever you are working in the
kitchen.
~ Older children may use the
rangehood only when its operation has
been clearly explained to them and
they are able to use it safely,
recognising the dangers of misuse.
~ Please be aware that on rangehoods
with halogen lighting, the lamps will get
very hot during use and remain hot for
some time after switching off. To
safeguard against burning, keep
children well away from the lamps at all
times.
Warning and Safety instructions
Technical safety
~ Before installation, check the
rangehood for visible signs of damage.
Under no circumstances should you
use a damaged appliance. A damaged
appliance is dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
on-site electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in any doubt.
~ The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly and, where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
~ Installation, maintenance and
repairs may only be carried out by a
Miele authorised person in accordance
with current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~ A damaged connection cable must
only be replaced by an approved and
suitably qualified technician.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
– it is switched off at the isolator, or
– the screw-out fuse is removed (in
countries where this is applicable), or
– the mains fuse is disconnected, or
– it is switched off at the wall socket
and the plug withdrawn.
5
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ This rangehood must not be
installed and operated in mobile
installations (e.g. on a ship).
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the warranty.
~ Great care should be taken when
using the rangehood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas cooktops or ovens which draw air
in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Warning and Safety instructions
There must be adequate ventilation of
the room when the rangehood is used
at the same time as appliances burning
gas or other fuels.
If the rangehood is being operated in
recirculation mode, the above
restrictions do not apply.
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the rangehood
and the heater are in operation
simultaneously, an underpressure of
0.04 mbar (4 pa) is the maximum
permissible in the room.
Correct use
~ Never use an open flame beneath
the rangehood. To avoid the danger of
fire, do not flambé or grill over an open
flame.
When switched on, the rangehood
could draw flames into the filter. Fat
particles drawn into the rangehood
present a fire hazard.
~ When using the rangehood over a
gas cooktop, ensure that any burners in
use are always covered by a pan.
Switch the cooking zone off when a pan
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The rangehood can become damaged
when exposed to excessive heat.
Ventilation can be maintained by air
inlets which must not be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the rangehood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter must be sought
~ Always switch the rangehood on
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc., do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the rangehood on fire.
If in any doubt , the advice of a
qualified builder, gas fitter or
electrician must be sought.
.
7
Warning and Safety instructions
~ Do not use the rangehood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ Accessible parts may become hot
when used with cooking appliances.
Do not touch the housing or the grease
filters until the rangehood has cooled
down.
~ Do not use a steam-cleaner to clean
this appliance. Steam could reach the
electrical components and cause a
short circuit.
Correct installation
~ Refer to the cooktop manufacturer's
instructions as to whether a rangehood
may be operated above the cooktop.
~ The minimum safety distances
between the top of the cooktop and the
bottom of the rangehood given in the
"Appliance dimensions" section of this
booklet must be maintained, unless the
cooktop manufacturer states that a
greater safety distance is required.
If more than one cooking appliance is
fitted beneath the rangehood, and they
have different minimum safety
distances to the rangehood, select the
greater distance.
8
~ Safety regulations prohibit the fitting
of a rangehood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from Miele or
from builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
~ Ensure exhaust ventilation complies
with all relevant regulations.
Accessories
~ Only use genuine Miele spare parts
and accessories with this appliance. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the warranty, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Description of the functions
The rangehood works with
. . . air extraction:
. . . air recirculation:
The air is drawn in and cleaned by the
grease filters and directed outside.
The air is drawn in and cleaned first by
the grease filters and then by a
charcoal filter.
If the on-site ventilation system does
not have a non-return flap, the
non-return flap supplied with the
appliance must be used.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the rangehood
is switched off.
When the rangehood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
The cleaned air is then recirculated
back into the kitchen through grilles in
the top of the rangehood.
Charcoal filters can be ordered as an
accessory from Miele (see "Technical
data").
Before using the rangehood in
recirculation mode, ensure that the
charcoal filter is in place. See "Cleaning
and care".
9
Operation
10
Operation
a Controls
Switching the lighting on/off
b Cooktop lighting
The cooktop lighting (j, l) can be
switched on and off independently of
the fan.
c Charcoal filter
Special accessory for recirculation
mode
"0" – Lighting off
d Cover for the charcoal filter duct
"1" – Lighting on
e Grease filters
Switching the fan on/off
f Exhaust socket C 125 mm or
150 mm
g Non-return flap
^ The controls k and m are used to
switch the fan on and off and to
select the fan power setting.
h Air outlet for air extraction
^ "0" – Fan off
i Air outlet for air recirculation
^ Settings "1" to "3" are usually
sufficient for normal cooking.
j Rotary control for the cooktop
lighting (DA 1050-55, DA 1060)
k Rotary control for the fan
(DA 1050-55, DA 1060)
^ DA 1160, DA 1100: When frying or
cooking food with a strong aroma,
you may wish to select the intensive
setting (IS) for a short period.
l Slide control for the cooktop
lighting (DA 1160, DA 1100)
After cooking
m Slide control for the fan (DA 1160,
DA 1100)
It is advisable to run the fan for a few
minutes after cooking has finished to
neutralise any lingering odours in the
air, whether you are using air extraction
or recirculation mode.
11
Cleaning and care
,Before any cleaning or
maintenance work is carried out,
disconnect the rangehood from the
mains supply. Ensure that
– it is switched off at the wall socket
and the plug is removed, or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed (in
countries where this is applicable).
,The halogen lamps get very hot
during use, and remain hot for some
time after being switched off.
The hot halogen lamps can be
damaged if water is used to clean
them.
To avoid burns to yourself or
damage to the lamps, wait several
minutes after switching off before
beginning cleaning.
Housing
General information
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
All external surfaces and controls can
be cleaned using warm water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
After cleaning, wipe the surfaces dry
using a soft cloth.
12
Do not use too much water when
cleaning the controls. Moisture
could penetrate into the electronics
and cause damage.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents. These will damage
the surface material.
Important for appliances with
stainless steel housing
(This infomation does not apply to the
controls)
Stainless steel surfaces can be cleaned
with a proprietary non-abrasive
cleaning agent designed specifically
for use on stainless steel.
To prevent immediate resoiling, the
Original Miele care product for stainless
steel can be purchased from Miele or at
www.miele-shop.com (depending on
country). Apply sparingly with a soft
cloth following the instructions on the
packaging.
Cleaning and care
Important for appliances with
lacquered housing
It is very difficult to clean this type of
surface without causing minor marks to
the surface material.
This can become particularly
noticeable if there is halogen lighting in
the kitchen.
Important information for cleaning
the controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long. Remove
soiling straight away.
Grease filters
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
rangehood.
To avoid a build-up of fat, they should
be cleaned every 3–4 weeks on
average, but sooner if necessary.
,An oversaturated filter is a fire
hazard.
Observe the general information on
cleaning earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
^ Open the latch for the grease filter
and lower the filter to remove it.
To avoid damaging the filter or the
cooktop below, make sure you hold
the filter securely at all times when
handling it.
13
Cleaning and care
Cleaning the grease filters by hand
^ Clean the filter with a soft nylon brush
in a mild solution of hot water and a
little washing-up liquid.
Do not use undiluted washing-up
liquid.
Do not use:
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
Cleaning the grease filters in the
dishwasher
^ Place the filters as upright as
possible in the lower basket. Ensure
the spray arm is not obstructed.
^ Do not wash at more than 65 °C. If a
Miele dishwasher is being used,
select the Sensor wash programme.
^ Use a mild dishwasher detergent.
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
14
^ After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
^ When removing the filters for
cleaning, also clean off any residues
of oil or fat from the now accessible
housing to prevent the risk of these
catching fire.
Cleaning and care
Charcoal filter
If the rangehood is connected for
recirculation (see "Installation"), a Miele
NoSmell active charcoal filter must be
inserted in addition to the grease filter.
^ Unwrap the charcoal filter from its
packaging.
^ Remove the grease filters.
^ Push the cover for the charcoal filter
duct slightly to the right and then
lower it to remove.
^ Place the charcoal filter in its duct
and push it up against the air outlet
grille.
^ Refit the cover and the grease filters.
Replace the charcoal filter when it no
longer absorbs kitchen odours
effectively. It should, however, be
replaced at least every six months.
^ Used charcoal filters can be
disposed of with the normal
household waste.
15
Cleaning and care
Changing a halogen lamp
^ Remove the grease filters.
^ Ensure the rangehood is
disconnected from the electricity
supply. To do this:
– switch off at the wall socket and
remove the plug, or
– remove the mains fuse, or
– remove the screw-out fuse (in
countries where this is applicable).
,Exercise caution when changing
halogen lamps. They get very hot
during use and remain hot for some
time after being switched off.
Let them cool down before you
change them.
^ Slightly loosen the lamp's fastening
screw.
^ Slide the screw and the lamp down.
^ Tighten the screw again.
^ Turn the halogen lamp anti-clockwise
and pull it out.
Replace it with a lamp of the same
type: GU/GZ 10, 230 V, 50W.
^ Refit the lamp by reversing the steps
shown above. Please observe the
manufacturer's instructions.
^ Refit the grease filters.
16
After sales service
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– your Miele Chartered Agent
or
– Miele
You will find the telephone number
of Miele on the back cover of the
manual.
Please quote the model and serial
number when contacting Miele. These
are shown on the data plate which is
visible when the grease filter is
removed.
Warranty
The warranty for this appliance is
2 years.
For further information, please refer to
your warranty booklet.
17
Appliance dimensions
DA 1050-55 . . . . . . . . . . . . B = 548 mm
DA 1060, DA 1160 . . . . . . . B = 598 mm
DA 1100 . . . . . . . . . . . . . . . B = 998 mm
Exhaust connection
C 150 mm or C 125 mm.
If the rangehood is replacing another
rangehood which had a construction
height of 150 mm, a spacer trim can be
used to cover the building-in space left
by the previous rangehood. The spacer
trim can be ordered as an accessory in
various widths:
– DAB 55 for DA 1050-55,
– DAB 60 for DA 1060, DA 1160,
– DAB 100 for DA 1100.
18
Appliance dimensions
Safety distance between cooktop and
rangehood
The minimum distances between
the top of a cooktop and the bottom
of the rangehood are as follows,
unless a greater distance is
specified by the manufacturer of
your cooking appliance:
Cooking appliance
Distance
S
Electric cooktop
600 mm
Open electric grill
650 mm
Deep fat fryer (electric)
650 mm
Multi-burner gas cooktop 650 mm
with maximum 45.4 MJ/h
total output, with no burner
having a greater output
than 16.2 MJ/h.
When deciding on the safety distance
between the cooktop and rangehood,
please note that a distance of 650 mm
above electric cooktops may be
preferable to give more working space
under the rangehood.
– Account should also be taken of the
height of the person who will be
using the rangehood most often.
They should have sufficient space to
work comfortably at the cooktop, and
be able to reach the rangehood
controls with ease.
– If positioned too high, extraction will
be inefficient.
– For distances greater than 750 mm,
the rangehood should be wider than
the chosen cooktop.
Multi-burner gas cooktop 760 mm
with total output greater
than 45.4 MJ/h, or a gas
cooktop including a single
burner with an output
greater than 16.2 MJ/h.
Single gas cooktop with a
maximum output of 21.6
MJ/h.
650 mm
Single gas cooktop with a
maximum output greater
than 21.6 MJ/h.
760 mm
See "Warning and Safety"
instructions for further information.
19
Installation
Before installation, it is important to
read the information given on the
"Warning and Safety instructions" at
the beginning of this booklet.
This is particularly crucial when
using the rangehood at the same
time as a heating appliance that
relies on oxygen from the same
room, which could result in the
build-up of toxic fumes.
^ Remove the grease filters.
The housing components of stainless
steel rangehoods have protective foil
around them to prevent them from
transport damage.
^ Please remove this foil from the
housing components and the frames
of the grease filters before installing
the rangehood. The foil can be
peeled off easily.
Extraction
Deflector
A deflector is inserted in the back of the
rangehood.
The position of the deflector is
determined by the operating mode.
In air extraction mode, it guides the air
outside through an opening at the back
of the housing.
In air recirculation mode, it closes the
opening and guides the air to the outlet
at the front.
^ Check the position of the deflector.
^ If necessary, change the position of
the deflector according to the
operating mode you are using.
20
Recirculation
^ To do this, push on the two latching
hooks, pull the deflector out, turn it,
and push it back in until it clicks into
place.
Installation
Installation under a wall unit
Several holes for fastening the
rangehood under a wall unit are
provided in the top of the housing.
,Use the fixing points indicated
^ For operation in recirculation mode,
cover the opening at the back of the
rangehood with the sticker supplied
with the NoSmell active charcoal filter
(optional accessory).
on the drilling template supplied
with the appliance, and use only the
screws designated for fixing to the
wall unit. Faulty installation can
damage the rangehood and impair
electrical safety (e.g. electric
shocks).
If using the recirculation mode with a
very deep wall unit it must be ensured
that the wall unit does not cover the
recirculation air outlet.
^ Adhere the cut-out drilling template
to the bottom of the cabinet.
^ Drill four fixing holes C 5 mm through
the bottom of the wall unit.
21
Installation
^ For extraction mode, you must also
cut out a 170 mm diameter hole in
the bottom of the wall unit.
^ If the mains connection cable is to be
fed through the wall unit, a hole will
also need to be cut out in the bottom
of the wall unit.
^ Lift the rangehood up under the wall
unit and feed the connection cable
through the respective hole in the
bottom of the wall unit.
^ From the inside of the wall unit, fasten
the rangehood to the wall unit using
the screws provided.
^ Refit the grease filters.
22
Fitting the rangehood to the
wall
You also have the option of fitting the
rangehood to the wall using two
mounting plates
^ Cut the drilling template to size and
position against the wall. The top
edge of the template indicates the
top edge of the rangehood.
Please refer to the safety distances
(S) to the cooktop in "Appliance
dimensions".
^ Mark and drill the four holes for the
mounting plates (C 8 mm).
^ Remove the drilling template.NoSmell
active
Installation
Remove the halogen lamps. To do this:
^ Slightly loosen the lamp's fastening
screw.
^ Fix the mounting plates to the wall
using the plugs and screws supplied.
^ Slide the screw and the lamp down.
^ Tighten the screw again.
,The screws and plugs are
designed for use in solid walls only.
For other types of wall construction,
alternative fixings will be required.
Make sure that the wall is able to
take the weight of the rangehood.
^ Turn the lamp anti-clockwise and pull
it out.
23
Installation
With air extraction mode:
^ Hang the rangehood on the mounting
plates.
^ Tighten the screws at the back of the
rangehood on the left and right. This
will adjust the pitch of the rangehood
and secure it against being lifted off
the mounting plates.
^ Refit the halogen lamps.
^ Refit the grease filters.
^ If using air extraction mode, install
the exhaust ducting and connections.
24
^ When using exhaust ducting
C 150 mm, separate the exhaust
socket at the tapered section with a
sharp knife.
For exhaust ducting C 125 mm,
install the exhaust socket without
modifications. Please note,
installation of 150 mm is
recommended.
^ If required, install the non-return flap.
Check that the flap opens easily and
closes by itself.
Installation
Before connecting the rangehood to
the electricity supply, please read
the "Electrical connection" and
"Warning and Safety instructions"
sections of this booklet.
^ Plug the connection cable into an
electrical socket.
^ Carry out a functional test by turning
on the fan.
– In air extraction mode air should not
come out of the air outlet at the front
of the rangehood.
^ Attach the exhaust ducting to the
exhaust socket, for example using a
flexible exhaust hose and a hose clip
(optional accessory).
^ Insert the exhaust socket into the
exhaust opening and secure it by
turning clockwise.
– In recirculation mode the air should
come out of the air outlet at the front
of the rangehood.
If this does not happen, the deflector is
not installed correctly (see "Deflector").
^ Fit the remainder of the exhaust
ducting (see "Connection for air
extraction").
With recirculation mode:
^ Fit the charcoal filter (see "Cleaning
and care").
25
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
Connection of this appliance should be
made via a suitable isolator or a double
pole fused spur connection unit which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
26
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety, it is advisable to install
a residual current device (RCD).
Contact a qualified electrician for
advice.
Important
This appliance is supplied for
connection to an AC 230 V single
phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue = neutral
Brown = live
WARNING:
THIS APPLIANCE MUST BE EARTHED
Connection for air extraction
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the rangehood at the same time as
another heating appliance which
relies on air from the same room.
The rangehood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– When ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre to ensure no condensate
drains into the appliance.
– If the exhaust is ducted through an
outside wall, a telescopic wall vent or
a roof vent (available as an optional
accessory) is recommended.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for extraction connection.
To achieve the most efficient air
extraction with the lowest noise levels,
please note the following:
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
– The diameter of the exhaust ducting
should not be less than 150 mm.
Important!
– If flat ducting is being used, the
cross section must not be smaller
than the cross sectional area of the
exhaust connection.
– The exhaust ducting should be as
short and straight as possible.
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
– Only use wide radius bends.
– The exhaust duct must not be kinked
or compressed.
– Ensure that all connections are
strong and airtight.
27
Connection for air extraction
Condensate trap
Silencer
(optional accessory)
(optional accessory)
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is installed to collect
and evaporate any condensate which
may occur. Condensate traps are
available for C 125 mm or C 150 mm
ducting.
To achieve even further reductions in
noise levels in air extraction mode, a
special silencer can be fitted in the
ducting system.
When installing a condensate trap,
ensure that it is positioned vertically
and, if possible, directly above the
exhaust connection. The arrow on the
housing indicates the direction of
airflow.
The silencer not only reduces noise
from the motor outside the house, but
also sounds from outside (e.g. traffic
noise). For this reason, the silencer
must be positioned as close as
possible to where the ducting leaves
the building a.
The most effective noise reduction is
achieved if two silencers are installed
one behind the other.
28
Technical data
DA 1050-55, DA 1060
DA 1160, DA 1100
Total rated load . . . . . . . . . . . . . . 300 W
Fan motor. . . . . . . . . . . . . . . 2 x 100 W
Cooktop lighting . . . . . . . . . . 2 x 50 W
Total rated load . . . . . . . . . . . . . . 340 W
Fan motor. . . . . . . . . . . . . . . 2 x 120 W
Cooktop lighting . . . . . . . . . . 2 x 50 W
Voltage . . . . . . . . . . . . . . . . . AC 230 V
Voltage . . . . . . . . . . . . . . . . . AC 230 V
Frequency. . . . . . . . . . . . . . . . . ~ 50 Hz
Frequency. . . . . . . . . . . . . . . . . ~ 50 Hz
Fuse rating . . . . . . . . . . . . . . . . . . . 10 A
Fuse rating . . . . . . . . . . . . . . . . . . . 10 A
Connection cable
length . . . . . . . . . . . . . . . . . . . . . . 1.5 m
Connection cable
length . . . . . . . . . . . . . . . . . . . . . . 1.5 m
Weight
DA 1060. . . . . . . . . . . . . . . . . . . 11.2 kg
DA 1050-55. . . . . . . . . . . . . . . . . . 11 kg
Weight
DA 1160. . . . . . . . . . . . . . . . . . . 11.2 kg
DA 1100. . . . . . . . . . . . . . . . . . . 14.6 kg
Fan throughput
Fan throughput
Extraction power according to
EN 61591
Extraction power according to
EN 61591
Extraction system C 150 mm:
Setting I . . . . . . . . . . . . . . . . . . 140 m3/h
Setting II . . . . . . . . . . . . . . . . . 200 m3/h
Setting III . . . . . . . . . . . . . . . . 310 m3/h
Extraction system C 150 mm:
Setting I . . . . . . . . . . . . . . . . .
Setting II . . . . . . . . . . . . . . . . .
Setting III . . . . . . . . . . . . . . . .
Intensive setting . . . . . . . . . . .
Recirculation with charcoal filter:
Setting I . . . . . . . . . . . . . . . . . . . 30 m3/h
Setting II . . . . . . . . . . . . . . . . . . 80 m3/h
Setting III . . . . . . . . . . . . . . . . 120 m3/h
Required for recirculation mode:
1 ActiveCharcoal filter DKF 18-1
160 m3/h
270 m3/h
350 m3/h
500 m3/h
Recirculation with charcoal filter:
Setting I . . . . . . . . . . . . . . . . . . . 40 m3/h
Setting II . . . . . . . . . . . . . . . . . 100 m3/h
Setting III . . . . . . . . . . . . . . . . 150 m3/h
Intensive setting . . . . . . . . . . . 200 m3/h
Required for recirculation mode:
1 ActiveCharcoal filter DKF 18-1
29
30
31
DA 1050-55
DA 1060
DA 1160
DA 1100
en - AU, NZ
M.-Nr. 09 712 770 / 01