Samsung CM1079 Service manual

BASIC
: CM1079
MODEL
: CM1099
MODEL CODE : CM1099/XEU
1. Precaution
6SHFL¿FDWLRQ
3. Disassembly and Reassembly
4. Troubleshooting
5. Wiring Diagrams
Refer to the service manual in the GSPN(see rear cover) for the more information.
‡&RQWHQWV
1. Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1-2 Special High Voltage Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
6SHFL¿FDWLRQV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
7DEOHRI6SHFL¿FDWLRQV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3-1 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3-2 Features & External Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4. Disassembly and Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4-1 Disassembly of Magnetron, Motor Assembly and Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4-2 Replacement of High Voltage Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4-3 Replacement of Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4-4 Replacement of Drive Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4-5 Replacement of Control Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
5-1 Malfunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
5-2 Unsatisfactory Cooking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
5-3 Part Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6. Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6-1 Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
8. Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
8-1 Model name standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
8-2 Customer inquiry cases and countermeasures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2
1. Precaution
3
1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary use,
repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as potentially
lethal high voltages and currents.
1-1 Safety precautions (
)
13. Design Alteration Warning: Use exact replacement
SDUWVRQO\LHRQO\WKRVHWKDWDUHVSHFL¿HGLQ
thedrawings and parts lists of this manual. This
is especially important for the Interlock switches,
described above. Never alter or add to the
mechanical or electrical design of the MWO.
Any design changes or additions will void the
manufacturer’s warranty. Always unplug the unit’s
AC power cord from the AC power source before
attempting to remove or reinstall any component or
assembly.
14. Never defeat any of the B+ voltage interlocks. Do not
apply AC power to the unit (or any of its assemblies)
unless all solid-state heat sinks are correctly
installed.
15. Some semiconductor (“solid state”) devices
are easily damaged by static electricity. Such
components are called Electrostatically Sensitive
Devices (ESDs). Examples include integrated
FLUFXLWVDQG¿HOGHIIHFWWUDQVLVWRUV,PPHGLDWHO\
before handling any semiconductor components or
assemblies, drain the electrostatic charge from your
body by touching a known earth ground.
16. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting the
positive lead; always remove the instrument’s ground
lead last.
17. When checking the continuity of the witches or
transformer, always make sure that the power is
OFF, and one of the lead wires is disconnected.
18. Components that are critical for safety are indicated
in the circuit diagram by shading,
or
.
19. Use replacement components that have the same
UDWLQJVHVSHFLDOO\IRUÀDPHUHVLVWDQFHDQGGLHOHFWULF
VWUHQJWKVSHFL¿FDWLRQV$UHSODFHPHQWSDUWWKDWGRHV
not have the same safety characteristics as the
RULJLQDOPLJKWFUHDWHVKRFN¿UHRURWKHUKD]DUGV
NOTE : Connect the oven to a 20A. When
connecting the oven to a 15A,make sure that circuit
breaker can operate.
1.
All repairs should be done in accordance with the
procedures described in this manual. This product
complies with Federal Performance Standard 21
CFR
2. Microwave emission check should be performed to
prior to servicing if the oven is operative.
3. If the oven operates with the door open :Instruct
the user not to operate the oven and contact
the manufacturer and the center for devices and
radiological health immediately.
4. Notify the Central Service Center if the microwave
leakage exceeds 5 mW/cm2.
5. Check all grounds.
6. Do not power the MWO from a “2-prong” AC cord.
Be sure that all of the built-in protective devices are
replaced. Restore any missing protective shields.
7. When reinstalling the chassis and its assemblies,
be sure to restore all protective devices, including:
nonmetallic control knobs and compartment covers.
8. Make sure that there are no cabinet openings
through which people --particularly children--might
insert objects and contact dangerous voltages.
Examples: Lamp hole,ventilation slots.
9. Inform the manufacturer of any oven foundto have
emission in excess of 5 mW/cm2 ,Make repairs to
bring the unit into compliance at no cost to owner
and try to determine cause. Instruct owner not to use
oven until it has been brought into compliance.
CENTRAL SERVICE CENTER
10. Service technicians should remove their watches
while repairing an MWO.
11. To avoid any possible radiation hazard,replace parts
in accordance with the wiring diagram. Also, use
only the exact replacements for the following parts:
Primary and secondary interlock switches, interlock
monitor switch.
12. If the fuse is blown by the Interlock Monitor Switch:
Replace all of the following at the same time:
Primary, door sensing switch and power relay, as
well as the Interlock Monitor Switch. The correct
adjustment of these switches is described elsewhere
in this manual. Make sure that the fuse has the
correct rating for the particular model being repaired.
4
1. Precaution
1-2 Special High Voltage Precautions
1.
2.
3.
High Voltage Warning Do not attempt to measure any of
WKHKLJKYROWDJHVWKLVLQFOXGHVWKH¿ODPHQWYROWDJHRIWKH
magnetron. High voltage is present during any cook cycle.
Before touching any components or wiring, always unplug
the oven and discharge the high voltage capacitor (See
Figure 1-1)
The high-voltage capacitor remains charged about 30
seconds after disconnection. Short the negative terminal
of the high-voltage capacitor to to the oven chassis. (Use a
screwdriver.)
+LJKYROWDJHLVPDLQWDLQHGZLWKLQVSHFL¿HGOLPLWVE\FORVH
tolerance, safety-related components and adjustments. If
WKHKLJKYROWDJHH[FHHGVWKHVSHFL¿HGOLPLWVFKHFNHDFK
of the special components.
H. V. Capacitor
H. V. Diode
Short
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with high current capabilities in the circuits of the HIGH
92/7$*(75$16)250(5VHFRQGDU\DQG¿ODPHQWWHUPLQDOV,WLVH[WUHPHO\GDQJHURXVWRZRUNRQRU
near these circuits with the oven energized.
'2127PHDVXUHWKHYROWDJHLQWKHKLJKYROWDJHFLUFXLWLQFOXGLQJ¿ODPHQWYROWDJHRIPDJQHWURQ
PRECAUTION
Servicemen should remove their watches whenever working close to or replacing the magnetron.
PRECAUTION
Never touch any circuit wiring with your hand nor with uninsulated tool during operation.
5
6SHFL¿FDWLRQV
2-1 Features
Product Features
- Light-Duty Professional Microwave Oven.
- Sanitary Stainless Steel Cavity.
- Easy-to-use Dial Control Type.
7DEOHRI6SHFL¿FDWLRQV
Items
Model
Model Basic
Model New
MODEL NAME
CM1079
CM1099
Power Source
230V~50Hz
230V~50Hz
1,600W
1,600W
230V / 1,050W (IEC-705)
230V / 1,050W (IEC-705)
2,450MHz
2,450MHz
OM75S(31)
OM75S(31)
Cooling fan motor
Cooling fan motor
Outside
517 x 297 x 412mm
517 x 297 x 412mm
Oven cavity
336 x 225 x 349mm
336 x 225 x 349mm
26Liter
26Liter
Net
17.5Kg
17.5Kg
Gross
19.0Kg
19.0Kg
UK
UK
Power consumption
Microwave
Output Power
Operating Frequency
Magnetron
Cooling Method
Dimensions
(W x H x D)
Volume
Weight
Export zone
6
3. Operating Instructions
3-1 Control Panel
1
2
3
1. COOKING POWER CONTROL KNOB
2. DEFROST
3. TIMER KNOB
7
3. Operating Instructions
3-2 Features & External Views
HANDLE
DOOR DOOR
LATCHES
VENTILATION HOLES
OVEN LAMP
CERAMIC PLATE
8
COOKING POWER
CONTOL KNOB
SAFETY
TIMER KNOB
INTERLOCK HOLES
4. Disassembly and Reassembly
4-1 Disassembly of Magnetron, Motor Assembly and Lamp
Remove the magnetron including the shield case, permanent magnet, choke coils and capacitors (all of which
are contained in one assembly)
Parts
Explaination Photo
Magnetron,
Motor Assembly
and Lamp
9
Explaination
1.
Disconnect all lead wires from
the magnetron and lamp.
2.
Remove a screw securing air
cover.
3.
Remove the air cover.
4. Disassembly and Reassembly
4-1 Disassembly of Magnetron, Motor Assembly and Lamp
Parts
Explaination Photo
Magnetron,
Motor Assembly
and Lamp
Explaination
4.
Remove screws securing the
magnetron to the wave guide.
5.
Take out the magnetron very
carefully.
6.
Remove two screws from the
back panel.
Take out the fan motor.
7.
10
4. Disassembly and Reassembly
4-1 Disassembly of Magnetron, Motor Assembly and Lamp
Parts
Explaination Photo
Magnetron,
Motor Assembly
and Lamp
Explaination
8.
Remove the oven lamp from
hole of air cover.
NOTE1: When removing the magnetron, make sure that its antenna does not hit any adjacent parts, or it may be
damaged.
NOTE2: When replacing the magnetron, be sure to remount the magnetron gasket in the correct position and
make sure the gasket is in good condition.
4-2 Replacement of High Voltage Transformer
Parts
Explaination Photo
Explaination
1.
Discharge the high voltage
capacitor.
2.
Disconnect all the leads.
High Voltage
Transformer
11
4. Disassembly and Reassembly
4-2 Replacement of High Voltage Transformer
Parts
Explaination Photo
Explaination
3.
Remove the mounting bolts.
4.
Replace the High Voltage
Transformer
After replace, reconnect the
OHDGVFRUUHFWO\DQG¿UPO\
High Voltage
Transformer
5.
PRECAUTION
Servicemen should remove their watches whenever working close to or replacing the magnetron.
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with high current capabilities in the circuits of the
+,*+92/7$*(75$16)250(5VHFRQGDU\DQG¿ODPHQWWHUPLQDOV,WLVH[WUHPHO\GDQJHURXVWRZRUNRQ
or near these circuits with the oven energized.
'2127PHDVXUHWKHYROWDJHLQWKHKLJKYROWDJHFLUFXLWLQFOXGLQJ¿ODPHQWYROWDJHRIPDJQHWURQ
12
4. Disassembly and Reassembly
4-3 Replacement of Door Assembly
Parts
Disassembly Photo
Explaination
Removal of
Door “C”
,QVHUWÀDWVFUHZGULYHULQWRWKHJDS
between Door “A” and Door “C” to remove
Door “C”. Be careful when handling Door
“C” because it is fragile.Then remove the
door assembly.
Removal
of Door
Assembly
Lift up the Door Assembly from Cavity.
Removal of
Door “E”
Following the procedure as shown in the
¿JXUHLQVHUWDQGEHQGDWKLQPHWDOSODWH
between Door “E” and Door “A” until you
hear the ‘tick’ sound.
‡ Insertion depth of the thin metal plate
should be 0.5mm or less.
Removal of
Key Door &
Spring
Remove pin hinge from Door “E”
Detach spring from Door “E” and key door.
13
4. Disassembly and Reassembly
4-4 Replacement of Drive Motor
Parts
Explaination Photo
Explaination
1.
2.
Take out the glass tray,
guide roller from oven cavity,
disconnect power.
Remove turn table motor cover
from case bottom.
CAUTION : Remove sharp edge
after cover removal.
Drive Motor
3.
4.
Disconnect leads from motor.
Remove the screws securing
motor to bottom of over cavity.
6.
5.
Lift out the motor.
When replacing the motor, be
sure to remount it in the correct
position.
NOTE : The shaft of motor should
¿WWLSFRXSOHU
Drive Motor
6.
COVER FIXING SCREW :
MATCHINE SCREW(6006-001170)
14
When reassemble a drive
motor cover. give a turn in a
ƒDQG¿[ZLWKDVFUHZ
NOTE : Bring the spare screw
from service center.
4. Disassembly and Reassembly
4-5 Replacement of Control Circuit Board
Parts
Explaination Photo
Explaination
1.
Removal of
Control Box
Assembly
SCREW
2.
3.
4.
CONTROL BOX
15
Disconnect the connectors from the
control box assembly.
Remove screws securing the control
box assembly
Remove the knobs of the control box
A’ssy
Remove the screw securing the
timer.
5. Troubleshooting
5-1 Malfunction
5-1-1 If oven malfunction
*Inspection method
Oven does not operate.
NO
Is Fuse OK?
Is Primary interlock
switch normal?
NO
YES
YES
Is the magnetron
temperature switch normal?
NO
Is Power Relay normal?
NO
Replace switch
NO
Power supply circuit check point
YES
Is SMPS power supply
cirduit normal?
NO
Do check power supply
circuit
NO
NO
Do check
Relay control circuit
NO
YES
Is the IC01 output of
PCB normal?
Relay control circuit check point
Is high voltage dioed
normal?
YES
Checking high
voltagecircuts
Is high voltage dioed
normal?
NO
YES
Is high voltage
capacitor normal?
NO
YES
Is magnetron normal?
16
NO
5. Troubleshooting
5-1-2 If food is not heated even though an oven works
Food is not heated even though an oven works.
Is the latch switch
operating normally?
NO
*Inspection method
Method to control latch switch
YES
Checking high voltage circuits
17
5. Troubleshooting
5-2 Unsatisfactory Cooking
Parts
Food is
not
heated.
Cause
Diagnosis
Remedy
1) Open cathode
of magnetron
Check the terminals with a multimeter to see
if the heater circuit is open.
Replace magnetron.
2) Defective H. V.
Diode
Check the H. V. Diode for continuity in the
reverse and normal directions using meter. If
there is continuity in the reverse direction, the
H. V. Diode may be faulty. (In this event H. V.
Capacitor will be hot)
Replace H. V. Diode.
3) Shorted
magnetron
Connect megger leads to quick-connect
terminal & body of the magnetron if there is
continuity, the magnetron may be fuse will be
blown) faulty. (In this case the main fuse will be
blown)
Replace magnetron.
4) Defective
magnetron
If there is a crack in the magnetron antenna
(dome), the magnetron is defective.
Replace magnetron.
5) Poor contact of
primary interlock
switch
Check if the screws are secured well to the
door hinge. and pressing it ON and OFF
repeatedly.
Replace or adjust.
6) Open coil of H.
V. Transformer
Check the continuity of primary coil and
secondary coil. If there is no continuity, H. V.
Transformer is defective.
Replace the H. V.
Transformer.
7) Shorted H. V.
capacitor
Check the continuity of capacitor.
If the capacitor shorts, the fuse blows
Replace the H. V.
Capacitor.
8) Monitor Fuse
out
&KHFNWKHPRQLWRUIXVHRQWKHQRLVH¿OWHU
Replace the Monitor
fuse
5-3 Part Check List
Symptom
Microwave
cooking does
not work.
Fan motor
does not
rotate.
Related Parts
Check Points
H.V.Transformer
1) Check if the primary and secondary coil is open or
shorted.
5HVLVWDQFHRISULPDU\FRLOŸ$SSUR[
5HVLVWDQFHRIVHFRQGDU\FRLO$SSUR[Ÿ
2) Check if the MGT Heater Voltage is approx. 3.3V AC.
Caution : High voltage !
Replace.
H.V.Capacitor
Check continuity of capacitor between two
terminals with H.V.wire lead removed.
The resistance should be approx. 10MW, it’s failure..
Replace.
H.V.Diode
1) If there is no continuity in forward, direction the
H.V.Diode is open.
2) If there is continuity in reverse direction, it’s shorted.
Replace.
Fan motor
Check if the motor coil is open.
Replace.
18
Remedy
6. Wiring Diagrams
6-1 Wiring Diagrams
(This Document can not be used without Samsung’s authorization)
10W15
0.90A
19
6. Wiring Diagrams
6-1 Wiring Diagrams
(This Document can not be used without Samsung’s authorization)
PRIMARY SWITCH
723
BLU
WHT
DOOR SENSING SWITCH
%27720
YEL
WHT
ORG
BLK
BRN
WHT
BRN
MONITOR SWITCH
&(17(5
WHT
BLU
F
MAGNETRON
FA
HIGH VOLTAGE
TRANSFORMER
R
RED
HIGH VOLTAGE
DIODE
TO CHASSIS
HIGH VOLTAGE CAPACITOR
COLOR
RED
SYMBOL
ORANGE
WHITE
BLACK
BLUE
RED
YELLOW
BROWN
RED
ORG
WHT
BLK
BLU
RED
YEL
BRN
20
7. Reference
7-1 Model name standard
%DRDG&ODVVL¿FDWLRQ
USA CMO
USA RV
Distinguisher
0LGGOH&ODVV¿FDWLRQ
Distinguisher
Product Code
Full Name
CMO (Counter-top MWO)
W
MW
USA CMO(EPOXY CAVITY)
UTC (Under The Cabinet)
U
MU
USA UTC
Browner, Grill
G
MG
USA GRILL
Convection
C
MC
USA CONVECTION
Sensor
S
MS
USA CMO SENSOR
DC MWO
D
MD
USA DC MWO
Hospital MWO
H
MH
USA Hospital MWO
Ceramic Enamel
E
ME
USA CMO(CERAMIC ENAMEL)
SOLO
M
RM
USA RV SOLO
CONVECTION
C
RC
USA RV CONVECTION
BUILT-IN
B
RB
USA RV BUILT-IN
-
-
SJ
USA Junior MWO
SOLO
H
SMH
USA OTR SOLO
CONVECTION
V
SMV
USA OTR CONVECTION
SOLO
1
M1
EUROPE SOLO(EPOXY CAVITY)
GRILL
2
M2
EUROPE GRILL(EPOXY CAVITY)
SOLO
1
CE1
EUROPE SOLO(CERAMIC ENAMEL)
GRILL
2
CE2
EUROPE GRILL(CERAMIC ENAMEL)
M
R
USA Junior
SJ
USA OTR
SM
EUROPE
Epoxy Cavity
M
EUROPE
Ceramic Enamel
CE
EUROPE
Quartz GRILL
G2
-
-
G2
EUROPE Quartz GRILL
EUROPE
Power Grill
PG
-
-
PG
POWER GRILL
CK
-
-
CK
EUROPE CONVECTION
C
-
-
C
EUROPE CONVECTION
SOLO
W
FW
EUROPE SOLO FULLY BUILT-IN
GRILL
G
FG
EUROPE GRILL FULLY BUILT-IN
CONVECTION
C
FC
EUROPE CONVECTION FULLY BUILT-IN
EUROPE
Convection
EUROPE
Fully Built-In
F
21
Exploded Views and Parts List
1. MAIN
Exploded View
Parts List
No.
Lvl.
Loc.
Material Code
Description & Specification
SNA
1
2
T002
DE97-00191A
ASSY-TRAY CERAMIC;
CM1049,-,T3.2,COMMERCI
SA
1
2
2
P001
DE97-00190A
ASSY STIRRER; CM1049,ALS
SA
1
2-1
3
T036
DE31-00009A
BLADE-STIRRER; CM1030M,ALP1050,T0.8
SNA
1
2-2
3
T074
DE60-80043A
SPACER-STIRRER; TEFLON,W6.3,T2
SNA
4
2-3
3
T037
DE61-00098A
HOLDER-STIRRER; CM1030M,TEFLON,WHT
SNA
1
2-4
3
M078
DE69-90054A
CLIP-STIRRER; 5mm,TEFLON-PFA,CM1819/29
SA
4
3
2
M051
DE71-00163A
COVER-CEILING; CM1049,MICA
SHEET,T0.5,W12
SA
1
4
2
M049
DE31-10173C
MOTOR SYNCHRONOUS;
SEMI-COMM,21V,16.7/20R
SA
1
5
1
DE96-00964C
ASSY POWER PACK; CM1079-A/XEU,0.8
CU.FT
SA
1
5-1
2
M038
DE26-00051B
TRANS H.V; SHV-E1049B,230V,50Hz,2360V/3.4
SA
1
6
2
M155
DE96-00240G
ASSY BASE PLATE; SEMI COMM 1059/1069,-,-,
SA
1
6-1
3
M045
DE96-00042A
ASSY BASE PLATE SUB; -,-,-,3RD-1.0,SEPARA
SA
1
Copyright© 1995-2012 SAMSUNG. All rights reserved.
Qty.
1
Exploded Views and Parts List
No.
Lvl.
Loc.
Material Code
Description & Specification
SNA
6-1-1
4
M048
DE80-10001G
BASE-PLATE; 3RD,GI-SGCC,T0.6,W345,L565
SNA
1
6-1-2
4
M047
DE61-40066A
FOOT; PP,BLK
SA
2
6-2
3
M042
DE91-70061H
ASSY H.V.FUSE; -,THV060T-0900-H,5KV0.90A,
SA
1
6-3
3
M527
DE59-00002A
DIODE-H.V; MWO ALL,2CL4512H,-,450mA
13KV,
SNA
1
6-4
3
M039
2501-001285
C-OIL; 1.13uF,2100V(CLASS P),AL CAN TYPE,
SA
1
6-5
3
M040
DE61-00419A
BRACKET-HVC; CM1049,EGI-SECC,T0.8
SNA
1
7
2
M011
DE61-50541A
BRACKET-EARTH; GI-SGCC,T1.0,W15,L8
SNA
1
8
1
B022
DE94-01862D
ASSY BODY LATCH;
MC455TCRCSR/XE,CONTRABAS
SNA
1
8-1
2
DE72-00137G
LATCH-BODY; AMC6158/JMC9158,PBT
SA
1
8-2
2
B048
3405-001034
SWITCH-MICRO;
125/250VAC,16A,200gf,SPST-N
SA
2
8-3
2
B046
3405-001032
SWITCH-MICRO; 125/250VAC,16A,200GF,SPDT
SA
1
8-4
2
B010
DE66-00093A
LEVER-SWITCH(A); NC2000,PP,NTR,HANDLE
SA
1
8-5
2
B011
DE66-00094A
LEVER-SWITCH(B); NC2000,PP,NTR,HANDLE
SA
1
9
1
W002
DE96-00743A
ASSY WIRE HARNESS-A; CM1059,-,TCM
SNA
1
10
2
M457
DE47-20173A
THERMOSTAT; NT-101,125/250V,905,605,1
SA
1
11
2
M035
OM75P(31)ESGN
ASSY-MGT; ASSY-MGT
12
2
M037
DE71-60016E
COVER-AIR; CM1049,PP,FH44N,SEMI-COM
SA
1
13
2
M036
4713-001524
LAMP-INCANDESCENT; 230V,20W
SA
1
14
2
M020
DE96-00108C
ASSY MOTOR FAN;
CM1059/XEU,230V50HZ,2500R
SA
1
14-1
3
P109
DE71-00061A
COVER-MOTOR; 2 & 2 PROJECT,PP,TB53,2 &
2 PROJ
SA
1
14-2
3
H096
DE31-90051A
BLADE-FAN; -,PP,-,D130,-,T,-
SA
1
14-3
3
M023
DE31-10177C
MOTOR FAN;
SMF-1049EA,-,-,230V50Hz,15mm,-
SNA
1
15
2
M017
DE96-00010C
ASSY NOISE FILTER; -,SN-3WED(12),250V12A,
SA
1
15-1
3
M019
3601-001019
FUSE-CARTRIDGE;
250V,12A,SLOW-BLOW,CERAMI
SA
1
16
1
M001
DE64-01740A
PANEL-OUTER;
CM1059/1069,STAINLESS-STS430
SA
1
17
1
M015
DE96-00180C
ASSY POWER CORD;
BSI,Flag,250V/13A,H07RN-
SA
1
18
2
M052
DE73-90027A
FERRITE-CORE; T13.8,NI-ZN,BNF-14(K150),L2
SA
1
19
2
DE69-00909A
PAD SHEET; ALL MODEL
CMO,HDPE,T0.03,W400,
SA
1
2
Qty.
1
Copyright© 1995-2012 SAMSUNG. All rights reserved.
Exploded Views and Parts List
2. ASSY DOOR
Exploded View
Parts List
No.
Lvl.
Loc.
Material Code
Description & Specification
SNA
1
1
D049
DE94-03005A
ASSY DOOR; CM1089,STSS,MANDOLIN
SA
1
1-1
2
D037
DE94-03002A
ASSY DOOR A; CM1089,STSS,MANDOLIN
SA
1
1-2-1
3
D019
DE64-02745A
HANDLE-DOOR;
COMMERCIAL,AL,MANDOLIN
SNA
1
1-3
2
D010
DE61-80003A
HINGE-LOWER;
ME6144W/XSA,SSEC,T2.3,W26,L7
SA
1
1-4
2
D009
DE61-80002A
HINGE-UPPER; WHT,SSEC,T2.3,W26,L77,ZPC3
SA
1
1-5
2
D011
DE64-00264A
KEY-DOOR; 3RD-W NEW,POM,-,-,BLK,-,-
SA
1
1-6
2
D007
DE61-00199A
SPRING-KEY; M1977,HSWR-SWRH,D6,25
1/4,25
SC
1
1-7
2
D004
DE92-50127H
ASSY DOOR E; -,-,BLACK,COATING,T0.8
SC
1
Copyright© 1995-2012 SAMSUNG. All rights reserved.
Qty.
3
Exploded Views and Parts List
No.
Lvl.
Loc.
Material Code
Description & Specification
SNA
1-8
2
D006
DE64-40012D
DOOR-C; JES1036NL02,ROH,EMBO HEIGHT
0.8mm
SA
1
1-9
2
D005
DE01-00002B
FILM-DOOR;
CM1089,PET,T0.15,W290,L169,NTR
SA
1
4
Qty.
Copyright© 1995-2012 SAMSUNG. All rights reserved.
Exploded Views and Parts List
3. ASSY CONTROL BOX
Exploded View
Parts List
No.
Lvl.
Loc.
Material Code
Description & Specification
SNA
1
1
C082
DE94-03007A
ASSY CONTROL BOX; CM1099,230V
50HZ,STSS S
SNA
1
1-1
2
F002
DE96-00738A
ASSY-TIMER CONTROL;
MW71E,DAM-TCM1-00,-,W
SA
1
1-3
2
C001
DE94-03006A
ASSY CONTROL PANEL; CM1099,STSS ST-430
T0
SA
1
1-4
2
C029
DE64-02753A
KNOB-DIAL;
COMMERCIAL,PC,HB,BLACK,MANDOLI
SNA
2
Copyright© 1995-2012 SAMSUNG. All rights reserved.
Qty.
5
7. Reference
7-1 Model name standard (Continued)
(Blue Color) : Not Used
Baoad
&ODVVL¿FDWLRQ
CHINA
KOREA
Distinguisher
C
D
EUROPE
USA
-
A
Distinguisher
Cavity / type
Distinguisher
SOLO / CMO
M
Inverter SOLO
I
CERAMIC
ENAMEL
E
CERAMIC
ENAMEL(Clay)
C
Epoxy
W
0LGGOH&ODVV¿FDWLRQ
Grill / Browner
G
Quartz Grill / Browner
Q
Conv.
C
TBMO / Power Grill
T
Commercial
O
STSS
S
CERAMIC
ENAMEL
E
CERAMIC
ENAMEL(Clay)
C
Epoxy
W
SOLO / CMO
M
Inverter SOLO
I
Grill / Browner
G
Quartz Grill / Browner
Q
Conv.
C
TBMO / Power Grill
T
Commercial
O
STSS
S
CERAMIC
ENAMEL
E
CERAMIC
ENAMEL(Clay)
C
Epoxy
W
SOLO / CMO
M
Inverter SOLO
I
Grill / Browner
G
Quartz Grill / Browner
Q
Conv.
C
TBMO / Power Grill
T
Commercial
O
STSS
S
CERAMIC
ENAMEL
E
CERAMIC
ENAMEL(Clay)
C
SOLO / CMO
M
Inverter SOLO
I
Grill / Browner
G
Quartz Grill / Browner
Q
Conv.
C
TBMO / Power Grill
T
Commercial
O
Epoxy
W
STSS
S
Full Name
CME / CMC / CMW / CMS
CIE / CIC / CIW / CIS
CGE / CGC / CGW / CGS
CQE / CQC / CQW / CQS
CCE / CCC / CCW / CCS
CTE / CTC / CTW / CTS
COE / COC / COW / COS
DME / DMC / DMW / DMS
DIE / DIC / DIW / DIS
DGE / DGC / DGW / DGS
DQE / DQC / DQW / DQS
DCE / DCC / DCW / DCS
DTE / DTC / DTW / DTS
DOE / DOC / DOW / DOS
ME / MC / MW / MS
IE / IC / IW / IS
GE / GC / GW / GS
QE / QC / QW / QS
CE / (CC) / (CW) / CST
TE / (TC) / TM / TST
OE / OC / OW / OS
AME / (AMC) / AMW / AMS
AIE / AIC / AIW / AIS
AGE / (AGC) / AGW / AGS
AQE / AQC / AQW / AQS
ACE / ACC / ACW / ACS
ATE / ATC / ATW / ATS
AOE / AOC / AOW / AOS
CHINA
C
SOLO(MW ONLY)
W
CFW / CFG / CFC / CFI / CFT
KOREA
D
GRILL
G
DFW / DFG / DFC / DFI / DFT
EUROPE
-
CONVECTION
C
DFW / DFG / DFC / DFI / DFT
USA
A
INVERTER
I
FW / FG / FC / FI / FPG
TBMO / Power Grill
T
AFW / AFG / AFC / AFI / AFT
Fully Built-In
F
USA OTR
SM
SOLO(MW ONLY)
H
SMH / SMB / SMV / SMI / STB
EUROPE OTR
EM
GRILL
G
EMH / EMG / EMV / EMI / EMT
CHINA OTR
UM
CONVECTION
V
UMH / UMG / UMV / UMI / UMT
KOREA OTR
PM
INVERTER
I
TBMO / Power Grill
T
CST : EUROPE STSS Conv.
FPG : EUROPE FBI POWER GRILL
TST : EUROPE TBMO with STSS cavity
SMB : USA Grill OTR
TM : EUROPE TBMO with epoxy cavity
STB : USA TBMO OTR
22
PMH / PMG / PMV / PMI / PMT
7. Reference
7-2 Customer inquiry cases and countermeasures
Symptom
Cause
‡
The oven works
automatically
whenever the power
is turned on.
‡
‡
‡
Heating
‡
‡
Ground
‡
‡
The oven sometimes
beeps.
‡
‡
Strange popping
sounds are produced
ZKLOH¿VKLVFRRNHG
Countermeasures
It may happen due
to power failure or
abnormal voltage.
It may happen when
the door does not close
completely.
‡
In many cases, it
may happen when
the power level is
incorrectly set.
It may happen when
the door does not close
completely.
It may happen when
the oven is out of order.
‡
Ground problem may
happen when the oven
is placed in a humid
area and the over is
not grounded.
Ground is not provided
by an extended electric
outlet.
‡
The oven beeps every
minute unless the food
is in the oven after
the food is cooked
completely.
The oven occasionally
beeps during cooking.
‡
‡
‡
‡
‡
6LQFH¿VKLVVDOW\DQG
‡
maintains its moisture,
it is cooked while
making a series of soft
popping sounds. (The
liquid may come out of
WKH¿VKZKHQWKH¿VKLV
cooked.)
23
Connect the power plug three seconds after
disconnecting the power plug.
Close the door completely => Press the Cancel button
=> Press the Start button.
Select HIGH/MEDIUM/LOW by pressing the Power
Level button.
- MEDIUM/LOW: This function is used to cook the food
slowly.
Close the door completely. => Press the Cancel
button. => Press The Start button.
Contact the nearest Samsung after-sales service
center.
If the oven is placed in a humid area, buy an electric
wire in a store selling electrical products. (Electric
wires for home use are also allowed) Ground the oven
through the electric wire.
Buy an electric wire in a store selling electrical
products. (Electric wires for home use are also
allowed) Ground the oven through the electric wire.
Open and close the door again. (Beeping sounds
indicate that the food is ready to be removed from the
oven after cooking is complete.)
)RRGZLWKERQHVVXFKDV¿VKHJPDFNHUHODQGSRUN
(e.g. pork chops) is cooked while making a series of
soft popping sounds. Wrap the food completely so that
food particles or spattered oils do not stick to the oven
ZDOOVRUÀRRU
7. Reference
7-2 Customer inquiry cases and countermeasures (Continued)
Symptom
Cause
‡
It may happen when
food particles stuck to
RYHQZDOOVRUÀRRU
‡
Clean the inside of the oven. => Remove strange
smell through the Deodorant button => If the strange
smell still remains, place a piece of lemon on the
turntable and operate the oven for 5 minutes by
pressing the Deodorant button.(However, the smells
produced from the food exposed such as herbal
remedies are not removed.)
‡
(UURUVDUHFODVVL¿HG
with Failure and Nonfailure.
‡
Refer to the section of ERROR in User Manual.
‡
Visit the nearest Samsung Service Center or local
dealer to buy accessories. Before visiting, check the
model name printed on the lower right side of the front
panel of the oven.
‡
Since the government recommends the reduction
of electricity, the power saving function is performed
for number display like that power cord is unplugged
when the oven is not used. (Numbers are displayed
when another button is pressed or when the door
opens.)
Strange smell is
produced in the oven.
Error
Countermeasures
Accessory
‡
Number does not
appear on the display
screen.
It happens when the
power saving function
is activated.
24
GSPN (GLOBAL SERVICE PARTNER NETWORK)
Area
Web Site
Europe, CIS, Mideast & Africa gspn1.samsungcsportal.com
Asia
gspn2.samsungcsportal.com
North & Latin America
gspn3.samsungcsportal.com
China
china.samsungportal.com
© Samsung Electronics Co., Ltd. March 2013
Printed in Korea