Motorola SYMBOL DS6707 Instruction manual

SYMBOL DS6707
DS6707 Poster
Quick Start Guide
http://www.symbol.com/ds6707
ACCESSORIES
See Product Reference Guide
for more information
2
BLACK
PANTONE 285
IntelliStand
Wall Mount
1
3
Desk Cup
POST IN WORK AREA
1 LED Indicators
2 Scan Window
3 Scan Trigger
CORD ATTACHMENT/REMOVAL
HOST INTERFACES
IMAGE CAPTURE
NOTE: Cables may vary depending on configuration
RS-232/SSI
USB
TROUBLESHOOTING
Scanner not working
No power to scanner
Scanner not decoding bar code
Incorrect interface cable used
Check system power;
ensure power supply,
if required, is connected
Interface/power cables are loose
Ensure that correct
interface cable is used
Ensure all cable connections
are secure
Scanner not programmed
for bar code type
Bar code unreadable
Ensure scanner is programmed
to read type of bar code being
scanned
Ensure bar code is not defaced;
try scanning test bar code of same
bar code type
Scanner decoding bar code, but data not transmitting to host
Scanned data incorrectly displayed on host
Scanner not programmed for correct host interface
Scanner not programmed for correct host interface
Scan appropriate host parameter bar codes
Interface cable is loose
Ensure all cable connections are secure
Distance between scanner
and bar code incorrect
Move scanner closer to
or further from bar code
Scan appropriate host parameter bar codes
Perforation
SYMBOL DS6707 PROGRAMMING BAR CODES
Set Defaults
SET DEFAULTS
Level
LEVEL
USB Host Types
Carriage Return/Line Feed
<DATA><SUFFIX 1>
SSI Host Types
HID KEYBOARD EMULATION
SNAPI WITH IMAGING
Baud Rate 9600
IBM HAND-HELD USB
SNAPI WITHOUT IMAGING
Baud Rate 38,400
ENABLE RS-232 (NO VARIANT)
NIXDORF RS-232 MODE B
Baud Rate 115,200
ICL RS-232
FUJITSU RS-232
NIXDORF RS-232 MODE A
OPOS/JPOS
RS-232 Host Types
SYMBOL DS6707
Aiming
2
DS6707 Poster
BLACK
OPTIMUM SCANNING AND IMAGING
1
PANTONE 285
012345
012345
012345
012345
3
1 LED Indicators
2 Scan Window
3 Scan Trigger
OPTIMUM ARM POSITION
AVOID EXTREME WRIST ANGLES
AVOID BENDING AND REACHING
AVOID BENDING
AVOID EXTREME
WRIST ANGLES
AVOID REACHING
Alternate left and right hands
taking breaks and task rotation
recommended
BEEPER INDICATIONS
LED INDICATIONS
Standard Use
Low/medium/high beep
Power up
Short mediun beep
4 long low beeps
Bar code decoded
Transmission error
detected; data is
ignored
Off
Scanner is on
and ready to scan,
or no power to
scanner
Green
Bar code is successfully
decoded
Red
Transmission
error
Parameter Menu Scanning
High/low/high/low beep
Successful
parameter
setting
High/low beep
Low/high beep
Correct programming
sequence performed
Incorrect
programming
sequence or
“Cancel” bar code
scanned
Local Contact:
Perforation
SYMBOL DS6707
REGULATORY INFORMATION
© 2008 MOTOROLA, INC. All rights reserved.
Ergonomic Recommendations
Warranty
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection
with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products
might be used. An implied license exists only for equipment, circuits, and
subsystems contained in Motorola products.
MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered
trademarks of Motorola, Inc. Other product names mentioned in this manual may
be trademarks or registered trademarks of their respective companies and are
hereby acknowledged.
For the complete Motorola hardware product warranty statement, go to:
http://www.symbol.com/warranty.
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow
the recommendations below. Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety programs to prevent
employee injury.
Regulatory Information
Patents
Symbol Technologies, Inc., the Enterprise Mobility business of Motorola, Inc.
("Motorola").
All Symbol devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Service Information
Any changes or modifications to Symbol Technologies equipment, not expressly
approved by Symbol Technologies, could void the user's authority to operate the
equipment.
This product is covered by one or more patents. For patent information go to:
http://www.symbol.com/patents.
If you have a problem using the equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Motorola Enterprise Mobility Support at: http://www.symbol.com/contactsupport.
For the latest version of this guide go to: http://www.symbol.com/manuals.
Radio Frequency Interference Requirements
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
FOR HOME OR OFFICE USE
reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Tested to comply
with FCC Standards
Waste Electrical and Electronic Equipment (WEEE)
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Motorola, Inc.
One Motorola Plaza Holtsville, New York 11742-1300, USA
Statement of Compliance
Symbol Technologies, Inc., hereby declares that this device is in compliance with all
the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may
be obtained from http://www2.symbol.com/doc
Laser Devices
Symbol products using lasers comply with US 21CFR1040.10, and EN60825-1:1994 +
A1:2002 + A2:2001, IEC 60825-1(ed. 1.2). The laser classification is marked on one of
the labels on the product.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
LASER LIGHT- DO NOT STARE INTO
BEAM . CLASS 2 LASER PRODUCT.
LASERSTRAHLUNG - NICHT IN DEN
STRAHL BLICKEN. LASER KLASSE 2.
LUMI»RE LASER - NE PAS REGARDER
DANS LE FAISCEAU. APPAREIL ¿ LASER
DE CLASSE 2 630-680nm, 1mW
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered
in the U.S. Patent and Trademark Office. All other product or service names are the
property of their respective owners.
© Motorola, Inc. 2008
72-83972-01 Revision B March 2008
SYMBOL DS6707
http://www.symbol.com/ds6707
Recommended Usage Guide