Radio Shack Add-On 2.4 GHzWireless Color Camera Owner`s manual

Please read before using this equipment.
Owner’s Manual
2.4 GHz Wireless Color System
The FCC Wants You to Know ........................................................................................... 2
Features .................................................................................................................................. 4
Installation ..............................................................................................................................
Camera Mounting Tips .....................................................................................................
Lighting and Your Camera’s Location ...............................................................................
Mounting the Camera .......................................................................................................
On a Wall ...................................................................................................................
On a Tripod ...............................................................................................................
Setting Up the Camera .....................................................................................................
Connecting the Receiver ..................................................................................................
To a TV without A/V Connectors ...............................................................................
To a TV with a DBS Receiver or Other A/V Device ...................................................
Setting the Remote Control’s House Code .......................................................................
Setting or Changing the Remote Control’s House Code ...........................................
Setting the Remote Control’s Unit Code ...........................................................................
Setting or Changing the Unit Code ............................................................................
5
5
5
5
5
6
6
7
7
8
8
8
8
8
Operation ................................................................................................................................
Using the Remote Control ................................................................................................
Scanning ..........................................................................................................................
All Four Cameras ......................................................................................................
Two or Three Cameras ..............................................................................................
9
9
9
9
9
Care ....................................................................................................................................... 10
Specifications ...................................................................................................................... 11
1
ˆ FCC Information
FCC DECLARATION OF
CONFORMITY
THE FCC WANTS YOU TO
KNOW
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
Product:
Model:
Responsible Party:
Phone:
2.4 GHz Wireless Color
System
49-2535
RadioShack
100 Throckmorton
Fort Worth, TX 76102
817-415-3200
WARNING: To reduce the risk of fire or shock hazard,
do not expose this product to rain or moisture.
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER OR BACK. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the product’s enclosure that might be
of sufficient magnitude to constitute a risk of
electric shock. Do not open the product’s
case.
!
This symbol is intended to inform you that
important operating and maintenance
instructions are included in the literature
accompanying this product.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or
antenna.
relocate
the
receiving
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult your local RadioShack store or
an experienced radio/TV technician for
help.
If you cannot eliminate the interference, the
FCC requires that you stop using your system.
© 2001 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
2
IMPORTANT SAFETY
INSTRUCTIONS
cause the product and cart combination to
overturn.
Read Instructions — All the safety and operating instructions should be read before
the product is operated.
Ventilation — Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating. Do not block or
cover these openings. These openings
should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or
rack unless proper ventilation is provided or
the manufacturer’s instructions have been
adhered to.
Retain Instructions — The safety and operating instructions should be retained for future reference.
Heed Warnings — All warnings on the product and in the operating instructions should
be adhered to.
Follow Instructions — All operating and
use instructions should be followed.
Cleaning — Unplug this product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Attachments — Do not use attachments
that are not recommended by the product
manufacturer as they may cause hazards.
Water and Moisture — Do not use the camera receiver near water (near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, for
example).
Accessories — Do not place this product on
an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage
to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use
a mounting accessory recommended by the
manufacturer.
Cart — A product and cart combination
should be moved with care. Quick stops, excessive force and uneven surfaces may
Power Sources — This product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type or power supply of your
home, consult your product dealer or local
power company. For products intended to
operate from battery power, or other sources, refer to the operating instructions.
Power-Cord Protection — Power supply
cords should be routed so that they are not
likely to be walked on or pinched by item
placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit
from the product.
Lightning — For additional protection to this
product during a lightning storm, or when it is
left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
prevents damage to the product from lightning and power-line surges.
Overloading — Do not overload wall outlet,
extension cords, or integral convenience receptacles as this can result in a risk of fire or
electric shock.
Object and Liquid Entry — never push objects of any kind into this product through
openings as they may touch dangerous volt-
3
age points or short-out parts that could result
in a fire or electric shock. Never spill liquid of
any kind on the product.
• if the product does not operate normally
by following the operating instructions
Servicing — Do not attempt to service this
product yourself as opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified
service personnel.
(Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls
may result in damage and often require
extensive work by a qualified technician
to restore the product to its normal operation.)
Damage Requiring Service — Unplug this
product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
• if the product has been dropped or damaged in any way
• when the product exhibits a distinct
change in performance (this indicates a
need for service)
• when the power supply cord or plug is
damaged
• if liquid has been spilled, or objects have
fallen into the camera receiver
• if the camera receiver
exposed to rain or water
has
been
Heat — The product should be situated
away from heat sources such as radiators,
heat registers, stoves, or other products including amplifiers that produce heat.
ˆ Features
Your RadioShack 2.4 GHz Wireless Color
System is a useful addition to your security
system. It includes a super small CMOS color camera with built-in 2.4 GHz transmitter, a
2.4 GHz receiver for connecting to a TV or
monitor, a 310 MHz signal transceiver with
built-in Plug ‘n Power adapter, and a remote
control.
The wireless camera converts the A/V (audio-video) signal from the camera into an RF
(radio frequency) signal, then transmits it to
the wireless RF receiver. The receiver converts the RF signal back to an A/V signal that
travels through a cable to your TV’s A/V input
jacks (or RF signal that travels through coaxial cable to your TV’s antenna input jack).
The system’s other features include:
4
CAMERA
Waterproof Housing Camera — lets you install the camera indoors or outdoors.
Built-In Microphone — lets you hear sound
from the area around the camera.
Color CMOS Sensor — provides superiorresolution images.
Range — you can use the system to monitor
up to 100 feet from the camera’s location.
Four Operating Channels — let you select
the best channel to avoid problematic interference.
Adjustable Camera Hinge — lets you adjust the camera to the desired coverage area.
Features
RECEIVER
Rotary Antenna — lets you easily adjust the
antenna for the best reception.
Audio/Video Out Jacks — let you see and
hear activity in the monitored area through
your TV or monitor, and record the action on
a standard VCR.
Non-Slip Rubber Feet — keep the video receiver in place on a hard, flat surface.
ˆ Installation
Note: Microwave ovens can cause interference. Be sure you do not position the video
camera or its receiver near a microwave.
CAMERA MOUNTING TIPS
Plan the cable’s route so it is not close to
power or telephone lines, transformers, or
other electrical equipment that could interfere with, or accept interference from the
system.
Before you install the camera, carefully plan
where you want to position the camera and
where you route the cable that connects the
camera to the power source.
Select a location for the camera receiver
which is convenient for connecting all other
components and within the reach of all connection cables.
If you plan to install the camera in a location
that has conditions not recommended in this
manual, consult with a professional installer
and consider use of a separate camera cover or housing.
LIGHTING AND YOUR
CAMERA’S LOCATION
Before starting a permanent installation,
have someone hold the camera while another person verifies its performance as you observe the monitor or TV. This helps
determine the best final position for your
camera.
When planning the installation, select a location for the camera that:
• provides a clear view of the area you
want to monitor
• is free from dust
• is not in line-of-sight with a strong light
source or in direct sunlight
• has an ambient temperature between
–4°F and 122°F (–20° and 50°C)
Though the camera is highly sensitive, it cannot “see” in total darkness over a wide area.
To assist the camera’s night vision, you can
install a 100W incandescent lamp (which is
rich in infrared radiation) to illuminate the
camera’s viewing area. You can also use a
small incandescent flood lamp. We do not
recommend using halogen lamps, other
high-pressure outdoor lamps, and fluorescent lighting.
MOUNTING THE CAMERA
You can mount the camera indoors or outdoors in a permanent location such as a wall
or on a movable platform (such as a tripod)
for mounting on a desk, shelf, or table.
On a Wall
1. Using the base of the camera as a
guide, mark the locations for the two
Installation
5
supplied mounting screws
desired mounting surface.
on
the
2. Drill a pilot hole at each marked location.
Drill a third hole, if necessary, below and
between the mounting holes for the
camera’s power socket cord.
Thread the camera’s power socket cord
through the hole, if necessary.
SETTING UP THE CAMERA
1. Gently grasp the rubber cover on the
front of the camera and lift it up to
remove it.
2. Use a pointed object (such as a straightened paper clip) to slide the channel
switch to the desired channel.
Notes:
3. Thread the screws through the holes in
the base and into the holes in the
mounting surface. Tighten each screw
until the base is secure.
• The four settings on the camera (from
bottom to top) are Channel A, B, C
and D, respectively.
• You must select the same channel for
both the camera and its receiver.
Antenna
3. Replace the rubber cover.
Base
Rubber Control
Cover
Power Socket
Cord
On a Tripod
To mount the camera on an optional tripod, thread the tripod’s
screw head into the screw hole
on the back of the camera and
tighten it.
4. Hold the camera’s base and gently
swivel the camera head until it is in position for the desired view.
Camera
5. Adjust the antenna so its flat side faces
the direction of the TV or monitor that
the receiver is connected to.
6. Plug the power plug of the supplied Plug
‘n Power adapter into the camera’s
power socket.
7. Use a small screwdriver to set the unit
and house code dials on the Plug ‘n
Power adapter. (You must also set the
remote control to the same code settings. See “Setting the Remote Control’s
House Code” on Page 8 and “Setting
the Remote Control’s Unit Code” on
Page 8.)
8. Connect the Plug ‘n Power adapter to a
standard AC outlet.
Warning: To avoid the risk of shock and prevent damage to your camera, always unplug
the Plug ‘n Power adapter from the AC outlet
before you unplug it from the camera.
6
Installation
CONNECTING THE
RECEIVER
3. Place the receiver in a convenient location.
You can power the receiver using the supplied 12V, 400 mA AC adapter.
4. Adjust the receiver’s antenna so its flat
side faces the direction where the camera is set up.
Cautions:
You must use a Class 2 power
source that supplies regulated 12V DC and delivers at
least 400 mA. Its center tip must be set
to positive and its plug must fit the
receiver’s DC 12V jack. The supplied
adapter meets these specifications.
Using an adapter that does not meet
these specifications could damage the
receiver or the adapter.
!
• Always connect the adapter to the
receiver before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you disconnect it from the receiver.
Note: To control more than one camera (up
to four cameras in all) using one receiver, follow the instructions in “Mounting the Camera” on Page 5 and “Setting Up the Camera”
on Page 6, then set all cameras’ channels to
the same channel as the receiver.
To a TV without A/V Connectors
Connect the supplied coaxial cable to the TO
TV jack on the back of the receiver and the
receiving TV’s antenna jack.
Note: If you already have an antenna connected to your TV, use a TV antenna splitter
(available at your local RadioShack store) to
allow you to connect the receiver as well.
1. Connect one end of the supplied A/V
cables to the receiver’s VIDEO OUT and
AUDIO OUT jacks (matching yellow to
yellow and white to white), then connect
the cable’s other ends to the receiving
TV or monitor’s A/V in jacks (again,
matching yellow to yellow and white to
white).
TV Antenna
Splitter
Receiver
TV
Set TV CHANNEL 3/4 on the bottom of the receiver to the same channel (3 or 4) on the receiving TV.
2. Plug the barrel plug of the supplied
adapter into the receiver’s DC 12V jack,
then plug its other end into a standard
AC outlet.
Installation
7
To a TV with a DBS Receiver or
Other A/V Device
tem to control any camera(s) set to the same
house code.
If your DBS receiver or other A/V component
is connected to the TV using A/V cables, you
can connect the receiver to the free LINE IN
jacks on the component. If there are no LINE
IN jacks, use a TV antenna splitter (available
at your local RadioShack store).
After you install the battery, the remote control is preset to house code A. The 1–4 ON/
OFF keys are set to unit codes 1, 2, 3, and 4
respectively.
SETTING THE REMOTE
CONTROL’S HOUSE CODE
To control a camera with a different unit
code, follow these steps to change the remote control’s unit codes.
The house code is a master code for a Plug
‘n Power system. You must set the camera
and the remote control to the same house
code. There are 16 codes to choose from
(A–P).
Notes:
Setting or Changing the Remote
Control’s House Code
1. Hold down 1 ON on the remote control.
After about three seconds, the light
blinks the current setting. For example,
the light blinks once for house code A,
twice for house code B, and so on.
2. Release 1 ON.
Setting or Changing the Unit Code
• You only need to change the unit code
of the 1 ON/OFF key. The other keys are
always one number higher than the previous one(s). For example, if you set 1
ON/OFF to unit code 5, 2 ON/OFF controls
6, 3 ON/OFF controls 7, and 4 ON/OFF
controls 8.
• The unit code must be set in sequence
of [1 2 3 4], [5 6 7 8], [9 10 11 12], or [13 14
15 16]. Setting the codes across any of
these sequences (such as 3 4 5 6)
causes the cameras to interfere with one
another.
3. Press 1 ON the appropriate number of
times for the house code you want to
set, such as once for A or twice for B.
The light blinks each time you press 1
ON. On the last press hold down 1 ON for
about 3 seconds. The light blinks the
new setting.
1. Hold down 1 OFF. After about three seconds, the light blinks the current setting.
For example, the light blinks once for
unit code 1, twice for unit code 2, and so
on.
Note: If you do not follow this programming
sequence, the light stays on for about 1 second and the existing setting is not changed.
3. Press 1 OFF the appropriate number of
times for the unit code you want to set.
The light blinks each time you press 1
OFF. Hold 1 OFF on the last press for
about 3 seconds. The light blinks the
new unit code.
SETTING THE REMOTE
CONTROL’S UNIT CODE
Every camera has a unit code dial with settings from 1–16. You can set the control sys-
8
2. Release 1 OFF.
Note: If you do not follow this programming
sequence, the light stays on for 1 second
and the existing setting is not changed.
Installation
ˆ Operation
Set the receiver’s ON/OFF switch to ON. The
red indicator on the front of the receiver
lights. Turn on the connected devices. If necessary, remove the camera’s focus panel
cap, then adjust the lens to set the focus.
Press the ON/OFF keys that have been set to
the corresponding unit codes to turn the
camera(s) on or off.
Notes:
• The cameras are preset to on when they
are connected to power.
If you cannot get any signal, make sure:
• the channel switches on both the camera and the receiver are set to the same
channel
• When you turn on one camera, the other
three are off.
• the TV and the TV CHANNEL 3/4 switch
on the bottom of the receiver are set to
the same channel (if you are using coaxial TV connections for the receiver)
• You can use the remote control and
transceiver to control lights and appliances connected to separate Plug ’n
Power modules, available at your local
RadioShack store.
• to turn on the camera using the remote
control
• To dim and brighten lights connected to
Plug ’n Power dimmer and light switch
modules, you must purchase additional
Plug ’n Power remote and transceiver
sets. Any additional sets and this system’s transceiver must be set to different
house codes in order to work properly.
If the signal is poor, or there is interference:
• Adjust the camera and receiver’s
antenna so they face one another.
• Change channels on both the camera
and the receiver.
SCANNING
To turn off the camera without using the remote control, unplug the Plug ’n Power
adapter from the AC outlet.
All Four Cameras
USING THE REMOTE
CONTROL
To scan through all four cameras, press
FORWARD or BACK on the remote control.
The four cameras turn on in sequence. Each
camera stays on the TV or monitor for about
5 seconds.
You can set the system up to control four
cameras, using the remote control. You can
find additional cameras at your local
RadioShack store.
See “Setting the Remote Control’s House
Code” on Page 8 and “Setting the Remote
Control’s Unit Code” on Page 8 to set up the
remote.
Two or Three Cameras
1. Reset the Plug ’n Power adapter by
unplugging it from, and re-plugging it
into, the AC outlet.
2. Press the ON key that corresponds to
the unit code for the first camera you
want to control.
Operation
9
Note: The Plug ‘n Power adapter’s transceiver sends the signal to turn each camera on
or off every 5 seconds. While the signal is
transmitting, you cannot use other Plug ‘n
Power control systems to control devices
connected with the same AC line. It takes
about 2 seconds for the signal to travel, so
your control system should respond by the
second key press. If you use the programmable timer control center (Cat.No. 612470), a device might not respond.
3. Press the ON key for the next camera
you want to be part of the group, then
press FORWARD or BACK.
The selected cameras turn on in sequence
every time you press FORWARD or BACK.
Each camera stays on the TV or monitor for
about 5 seconds.
Reset the Plug ‘n Power adapter each time
you change the camera scan settings.
To stop scanning, press any ON/OFF key. To
continue the scan, press FORWARD or BACK.
ˆ Care
Warning: Keep button-cell batteries away
from children. Swallowing a button-cell battery can be fatal.
Keep the system dry; if it gets wet, wipe it dry
immediately. Use and store the system only
in normal temperature environments. Handle
the system carefully; do not drop it. Keep the
system away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it
looking new.
Caution: Use only a fresh battery of the required size and recommended type.
1. Gently pry the remote control apart.
Modifying or tampering with the system’s internal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
system is not performing as it should, take it
to your local RadioShack store for assistance.
2. Remove the old battery. Place the fresh
battery in the compartment with its positive side (+) facing up.
3. Replace the cover.
When the system stops operating properly,
replace the batteries.
REPLACING THE REMOTE
CONTROL’S BATTERY
Warning: Dispose of old batteries promptly
and properly. Do not burn or bury them.
The remote control comes with one CR2032
lithium battery for power. For the best performance and longest life, we recommend a
RadioShack battery.
10
Care
ˆ Specifications
CAMERA
Imager ......................................................................................................................... CMOS Color Sensor
Format .................................................................................................................................................. 1/3 in
Focal Length ..................................................................................................................................... 5.6 mm
Focus Distance ........................................................................................................................ 20 cm Infinite
Field Angle .............................................................................................................................................. 60°
Array Size ......................................................................................................................... NTSC: 510 × 492
Resolution ................................................................................................................................ 310 TV lines
Scanning ................................................................................................................................... 2:1 interlace
Video Output ............................................................................................................................. 2V p-p, 75Ω
Auto Shutter ......................................................................................................... 1/60 to 1/15,000 seconds
Image Area (mm) ........................................................................................................... NTSC: 4.69 × 3.54
Gamma Correction ...................................................................................................................... 0.45 on/off
Signal to Noise Ratio (S/N) .............................................................................................................. > 42 dB
Minimum Illumination ............................................................................................................................. 5 lux
Supply Voltage for Lens ..................................................................................................................... 5V DC
Input Voltage .................................................................................................................................... 12V DC
Power Requirements ....................................................................................................................... 200 mW
Operating Temperature .................................................................................... –4° to 122°F (–20° to 50°C)
Humidity Limits .................................................................................................................................. 0–95%
Sensor Package ......................................................................................................................... 48 Pin LCC
RF Output ...................................................................................................................... 50,000 uV/m @ 3m
Modulation ..................................................................................................................... FM (Video & Audio)
RECEIVER
Channels .................................................................................................................................................... 4
Operating Frequencies (GHz)
Channel A ...........................................................................................................................
Channel B ...........................................................................................................................
Channel C ...........................................................................................................................
Channel D ...........................................................................................................................
2.411 GHz
2.434 GHz
2.453 GHz
2.473 GHz
Channel Bandwidth .......................................................................................................................... 18 MHz
Transmission Range ............................................................................................................................ 100 ft
Sensitivity .......................................................................................................................................... –90 dB
Video Output Level ............................................................................................................................. 1 Vp-p
Audio Output Level ............................................................................................................................. 1 Vp-p
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
Specifications
11
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
12/99
49-2535
01A01
Printed in China