Samsung SNV-5080R User manual

NETWORK CAMERA
User Manual
SNV-5080R
Network Camera
User Manual
Copyright
©2012 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
™™ Design and specifications are subject to change without prior notice.
™™ The default password can be exposed to a hacking thread so it is recommended to change the password
after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible
for the user.
overview
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
● overview
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/ accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13.Unplug this apparatus during lighting storms or when unused for
long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
English _3
overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling
in accordance with the installation instructions.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
4_ overview
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.
Please use the input power with just one camera and other devices must not
be connected.
English _5
● overview
Battery
overview
Please read the following recommend safety precautions carefully.
yy Do not place this apparatus on an uneven surface.
yy Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
yy Do not place this apparatus near conductive material.
yy Do not attempt to service this apparatus yourself.
yy Do not place a glass of water on the product.
yy Do not install near any magnetic sources.
yy Do not block any ventilation openings.
yy Do not place heavy items on the product.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
yy Reference : In case of providing information for helping of product’s usages
yy Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
 Please read this manual for the safety before using of goods and keep it in the safe place.
6_ overview
CONTENTS
overview
installation &
connection
14
network connection
and setup
26
11
12
Important Safety Instructions
Product Features
Recomended PC Specifications
Recomended SD/SDHC Memory
Card Specifications
What’s Included
At a Glance
14Installation
20 Inserting/Removing a SD Memory
Card
21 Memory Card Information
(Not Included)
22 Connecting with other Device
26
27
28
29
30
31
35
36
38
38
Connecting the Camera Directly
to Local Area Networking
Connecting the Camera Directly
to a DHCP Based DSL/Cable
Modem
Connecting the Camera Directly
to a PPPoE Modem
Connecting the Camera to a
Broadband Router with the
PPPoE/Cable Modem
Buttons used in IP Installer
Static IP Setup
Dynamic IP Setup
Port Range Forward (Port Mapping)
Setup
Connecting to the Camera from a
Shared Local PC
Connecting to the Camera from a
Remote PC via the Internet
English _7
● overview
3
3
9
10
10
overview
web viewer
39
setup screen
51
appendix
93
8_ overview
39 Connecting to the Camera
40Login
41 Installing Silverlight Runtime
45 Installing STW WebViewer Plugin
46 Using the Live Screen
48 Search and play by event
49 Search and play by time
51Setup
51 Video & Audio Setup
63 Network Setup
72 Event Setup
86 System Setup
93Specification
97 Product Overview
99Troubleshooting
101 Open Source Announcement
Product Features
M
`` However, MPEG-4 video can not be played on a web page. Use CMS software if you want to play
the video on a web page.
yy Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
yy Alarm
If an event occurs, the event-related video will be transferred to the FTP/email specified
by the user or saved to the SD memory, or the event signal will be sent to the Alarm Out
port.
English _9
● overview
yy Dustproof/Waterproof (IP66)
The dustproof and waterproof design makes you feel at ease when installing the product
outdoors or exposing it to rain.
yy SSNR3 (Samsung Super Noise Reduction)
The W-V powerful DSP chip reduces the gain noise effectively to remove the time lag so
that it can provide a sharp and clear image in a low contrast scene.
yy Day & Night (ICR)
It automatically detects the time change of the day to switch to a mode that is appropriate
to the current scene. In a daylight scene, it switches to the color mode for maintaining
the optimal color tones while it, at night, switches to B/W mode for identifying the low
contrast scene.
yy IR mode
If the IR indicator turns on, the product switches to the IR mode for preventing an object
from being too bright, which helps you identify the object in near distance.
yy Visibility: 15m
In B/W mode, the IR indicator turns on with the effective visibility of 15m at 0 Lux.
yy SSDR (Samsung Super Dynamic Range)
For a scene showing a great contrast difference such as backlight scene, the product
maintains the bright areas while selectively making the dark areas brighter to balance the
overall contrast.
yy Others
Other features include: HLC (High Light Compensation), SENS-UP, V-REV, H-REV,
D-ZOOM, SHARPNESS, Motion Detection, PRIVACY.
yy HD Video Quality
yy Multi-Streaming
This network camera can display videos in different resolutions and qualities
simultaneously using different CODECs.
overview
yy Tampering Detection
Detects tempering attempts on video monitoring.
yy Motion Detection
Detects motion from the camera’s video input.
yy Intelligent Video Analysis
Analyzes video to detect logical events of specified conditions from the camera’s video
input.
yy Auto Detection of Disconnected Network
Detects network disconnection before triggering an alarm.
yy ONVIF Compliance
This product supports ONVIF.
For more information, refer to www.onvif.org.
Recomended PC Specifications
yy CPU : Intel(R) Core(TM)2 2.00 GHz or higher
yy Operating System : Windows XP, VISTA, 7, Mac OS
yy Resolution : 1280X1024 pixels or higher
yy RAM : 1GB or higher
yy Web Browser : Internet Explorer 7.0 or Higher, Firefox 3.0 or Higher, Chrome 8.0 or
Higher, Safari 4.0 or Higher
`` Neither a beta test version unlike the version released in the company website nor the developer version will
be supported.
`` It is recommended to connect to IPv6 in Windows 7.
yy Video Memory : 128MB or higher
the driver of the video graphic adapter is not installed properly or is not the latest version, the
JJ `` Ifvideo
may not be played properly.
`` For a multi-monitoring system involving at least 2 monitors, the playback performance can be
deteriorated depending on the system.
Recomended SD/SDHC Memory Card Specifications
yy 4GB ~ 32GB
yy It is recommended to use memory cards of at least class 6 speed.
10_ overview
What’s Included
Please check if your camera and accessories are all included in the product package.
Item Name
User Manual,
Installer S/W CD,
CMS S/W DVD
Quantity
Description
2
Quick Guide
1
Template
1
Product installation guide
ASSY-Tapping Screw
4
Used for installation on the wall or ceiling
L Wrench
1
Used to remove/fix the dome cover
Plastic Anchor
4
For fixing a screw, Inserted in a hole
(reinforced anchoring force)
Machine Screws
4
Used for assembling the dome case when
installing the product on the pipe, wall
mount, etc. or blocking a hole.
Cable for the testing monitor
1
Used to test the camera connection to a
portable display device
Rubber cap
3
Insulation cap for improved
EMC performance.
English _11
● overview
Appearance
overview
At a Glance
Appearance
Item
a
b
c
d
e
f
g
h
Top cover
Camera Case
Power Port
Alarm In /
Out terminals
Network Port
Video Out Port
Audio In Jack
Audio Out Jack
12_ overview
Description
8
Case cover used to protect the lens and the main unit.
Covers the lens and camera body.
Used to plug the power cable.
ARM-IN
BLUE : Used to connect the alarm input signal.
A-COM
GRAY : Common port where the alarm output signal is
connected.
ARM-OUT
GND
WHITE : Used to connect the alarm output signal.
YELLOW : Used for earth-grounding.
Used to connect a PoE or LAN cable.
Analog video output port. (for installation)
Used to connect to a microphone.
Used to connect to speakers.
Inside
● overview
4
3
Item
a
Monitor Out
Description
Using the test monitor cable, you can connect to a mobile display for camera
test. (for installation)
Resets the camera settings to the default. Press and hold for about 5
seconds to reboot the system.
J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.
b
Reset Button
c
SD Memory Card
Compartment
Compartment for the SD memory card.
d
IR LED
It prevents an object from being too bright, which helps you identify the
object in near distance.
English _13
installation & connection
Installation
Precautions before installation
Ensure you read out the following instructions before installing the camera:
yy Select an installation site (ceiling or wall) that can endure at least 5 times of the
camera weight.
yy Stuck-in or peeled-off cables can cause damage to the product or a fire.
yy For safety purposes, keep anyone else away from the installation site. And put aside
personal belongings from the site, just in case.
Disassembling
1. With the provided L-shaped
wrench, loosen 3 bolts on the top
cover counter clockwise to remove
the cover.
Top cover
Bolts
Camera Body
Camera Case
2. Loosen 3 screws on the camera body
counter clockwise, and push down the
left/right LOCKER lever (in the arrow
direction) to release the lock. Then,
remove the camera from the case.
14_ installation & connection
LOCKER Lever
Installing on the ceiling directly
1. Remove the top cover from the case by referring to the “Disassembling” section.
(page 14)
3. Fit the bottom hole to the anchor hole and insert
and fix the ASSY taping screw (TH M4×L30).
`` When assembling the camera case to a junction box, select
appropriate screw holes on the case bottom for installation.
4. Connect and arrange the necessary cables lest that
they should be damaged or twisted while installing
the camera.
5. Install the camera body in the reverse order of
“Disassembling”.
CAMERA FRONT
6. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring
direction for the camera” section. (page 19)
7. Close the top cover.
`` To ensure waterproofing, tight up the fixing bolts using the L-wrench.
`` For improved EMC performance, it is recommended to
use the insulation cap provided as an accessory. (x3)
English _15
● installation & connection
2. Drill a hole (diameter: 5mm, depth: min 35mm) in a
desired position of the case bottom and insert the
provided plastic anchor (HUD 5) to the end.
installation & connection
Ceiling mount
1. Remove the top cover from the case by
referring to the “Disassembling” section.
(page 14)
2. Use the provided template to drill one hole for
the camera, and one for the screw (5 mm in
diameter, at least 35 mm in depth), and insert
the plastic anchor (HUR 5) to the end of the
screw hole.
3. Connect and arrange the necessary cables
lest that they should be damaged or twisted
while installing the camera.
4. Loosen and remove the case-fixing screws on the camera unit. (x3)
5. Insert the camera unit into the hole so that it fits to the camera hole, and fix the unit
using the ASSY tapping screws (TH M4×L30). (x3)
6. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring
direction for the camera” section. (page 19)
7. Close the top cover.
`` To ensure waterproofing, tight up the fixing bolts using the L-wrench.
16_ installation & connection
Attaching to the unbundled adapter
Choose and purchase a necessary one of the following options (unbundled) that is suitable
to the installation site or for your convenience.
● installation & connection
1. Remove the top cover from the case by referring to
the “Disassembling” section. (page 14)
2. Use the provided machine screw to fix the camera
case to the unbundled adapter.
3. Connect and arrange the necessary cables lest that
they should be damaged or twisted while installing
the camera.
4. Install the camera body in the reverse order of
“Disassembling”.
5. Adjust the lens in a desired direction by referring to
the “Adjusting the monitoring direction for the
camera” section. (page 19)
6. Close the top cover.
`` To ensure waterproofing, tight up the fixing bolts using the L-wrench.
Optional Accessories for Installation
For your easier installation, you can purchase appropriate optional accessories available.
1. WALL MOUNT ADAPTOR(SBP-300WM or
SBP-300WM1)/HANGING MOUNT(SBP300HM3)
This adaptor is used when installing the
dome camera onto a wall.
English _17
installation & connection
2. CEILING MOUNT ADAPTOR(SBP-300CM)/
HANGING MOUNT(SBP-300HM3)
This adaptor is used when installing the dome
camera on a concrete ceiling.
3. POLE MOUNT ADAPTOR(SBP-300PM)
This is an adaptor for WALL MOUNT ADAPTOR
(SBP-300WM or SBP-300WM1) installation on a
pole whose diameter is bigger than 80mm.
4. CORNER MOUNT ADAPTOR (SBP-300KM)
This is an adaptor for WALL MOUNT ADAPTOR
(SBP-300WM or SBP-300WM1) installation on
the corner of wall joint.
18_ installation & connection
Adjusting the monitoring direction for the camera
Panning
● installation & connection
Tilting
Lens rotation
Cover front
`` Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called
Tilt, and turning the lens on its axis is called Rotate.
-- The effective range of pan is a total of 355 degrees.
-- The effective range of rotation is a total of 355 degrees.
-- The effective range of tilt is a total of 90 degrees.
JJ
`` In some angles, the top cover may cause cutting some part of the monitoring object.
`` Do not rotate the focus/zoom lens by force after removing the cover front.
Otherwise, it may cause an incorrect focus due to a motor failure.
`` Methods of adjustment
1. After installing the camera, adjust the panning angle in consideration of the
monitoring direction.
When tilting the camera, you should adjust the horizontal angle lest that the image
be displayed reversely.
2. Adjust the rotation angle to correct the image display position (up/down/left/right).
`` Rotating means rotation on the basis of the rear lens unit.
3. Adjust the tilt angle so that the camera faces toward the monitoring object.
English _19
installation & connection
Inserting/Removing a SD Memory Card
JJ `` Disconnect the power cable from the camera before inserting the SD memory card.
Inserting a SD Memory Card
Push the SD memory card in the direction of the arrow shown in the diagram.
insert the SD memory card while it’s upside down by force. Otherwise, it may damage the
JJ `` DoSD not
memory card.
Removing a SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to
eject the memory card from the slot.
too hard on the SD memory card can cause the card to shoot out uncontrollably from
JJ `` Pressing
the slot when released.
`` To remove the SD memory card, set the card to <Off> in <Storage> menu and press
[Apply (
)] button. (Page 74)
`` Removing the SD memory card while it’s in use for saving may damage the data stored in the
card.
20_ installation & connection
Memory Card Information (Not Included)
What is a memory card?
Selecting a memory card that’s suitable for you
Your camera supports SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of
the memory card.
For your camera, we recommend you use a memory card from the following
manufacturers:
SD/SDHC Memory Card : Sandisk, Transcend
Memory cards of 4GB ~ 32GB is recommended for using with this camera.
Playback performance can be affected depending on the speed of memory card, so use
the high-speed memory card.
It is recommended to use memory cards of at least class 6 speed.
Memory Card Use
SD and SDHC memory cards feature a switch that disables writing data on to the media.
Having this switch to the Lock position will prevent accidental deletion of data stored in the
memory card but at the same time will also prevent you from writing data on to the media.
`` Memory Card Components
Contacts
Lock Switch
SD/SDHC
English _21
● installation & connection
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
installation & connection
Connecting with other Device
Monitor Out
Power
Ethernet
Monitor
BNC Out terminal of the product is provided for easier installation, and is not recommended
JJ `` The
for monitoring purposes. If you keep the BNC cable connected, a risk of lightening may cause
damage or malfunction to the product.
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
22_ installation & connection
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
`` The heater will operate properly only by the power source of AC 24V.
`` If using PoE, the heater will not operate at all.
Use an adaptor if the installation site requires heater operations. Adaptor is sold separately.
For the power specifications, refer to the “Appendix”. (page 96)
`` If PoE and DC 12V are both applied, this camera will get supplied with power from PoE.
`` Please make sure the monitor and camera are turned off when connecting them.
English _23
● installation & connection
not to reverse the polarity when you connect the power cable.
JJ `` BeYoucareful
can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
installation & connection
Connecting to Audio Input/Output
Speaker
Microphone
PC
Network
Amp
Microphone
Microphone
Speaker
Amp
Speaker
24_ installation & connection
1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT
port of the amplifier that the microphone is connected to.
2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
3. Check the specifications for audio input.
● installation & connection
yy Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
yy Full duplex Audio
yy Audio in
Used for mono signal line input (Max.2.4 Vpp)
yy Audio out
Used for mono signal line output (Max.2.4 Vpp)
yy Line out impedance
600Ω
Alarm I/O Wiring Diagram
ARM-IN
ARM-OUT
A-COM
(5mA sink)
(30VDC 2A,
125VAC 0.5A MAX)
GND
English _25
network connection and setup
You can set up the network settings according to your network configurations.
Connecting the Camera Directly to Local Area
Networking
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
Camera
INTERNET
Switch
Camera
External Remote PC
Firewall
DDNS Server
(Data Center, KOREA)
Local PC
<Local Network>
remote PC in an external Internet out of the LAN network may not be able to connect to the
MM `` Acamera
installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
`` By factory default, the IP address will be assigned from the DHCP server automatically. If there is
no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 31)
26_ network connection and setup
Connecting the Camera Directly to a DHCP
Based DSL/Cable Modem
Camera
External Remote PC
DDNS Server
(Data Center, KOREA)
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
MM `` For registering the DDNS settings, refer to “Registering with DDNS”. (page 66)
`` For configuring the DDNS settings, refer to “DDNS”. (page 65)
`` For setting the network type, refer to “Interface”. (page 63)
English _27
● network connection and setup
INTERNET
DSL/Cable
Modem
network connection and setup
Connecting the Camera Directly to a PPPoE
Modem
INTERNET
PPPoE Modem
External Remote PC
Camera
DDNS Server
(Data Center, KOREA)
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [PPPoE].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
MM `` For registering the DDNS settings, refer to “Registering with DDNS”. (page 66)
`` For configuring the DDNS settings, refer to “DDNS”. (page 65)
`` For setting the network type, refer to “Interface”. (page 63)
28_ network connection and setup
Connecting the Camera to a Broadband Router
with the PPPoE/Cable Modem
This is for a small network environment such as homes, SOHO and ordinary shops.
INTERNET
Camera
Broadband
Router
PPPoE or
Cable Modem
PPPoE or
Cable Modem
External Remote
PC
DDNS Server
(Data Center, KOREA)
Local PC
Configuring the network settings of the local PC connected to a
Broadband Router
Configuring the network settings of the local PC connected to a Broadband Router, follow
the instructions below.
yy Select : <Network Neighborhood>  <Properties>  <Local Area Connection>
 <Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties> 
<Obtain an IP address automatically> or <Use the following IP address>.
yy Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1
IP address : 192.168.1.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1
IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1
IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
the address of the Broadband Router, refer to the product’s documentation.
MM ```` For
For more information about port forwarding of the broadband router, refer to “Port Range
Forward (Port Mapping) Setup”. (Page 36)
English _29
● network connection and setup
Camera
network connection and setup
Buttons used in IP Installer
Item
Description
a
Device Name
Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b
Alias
This function is not currently implemented.
c
Mode
Displays either <Static>, <Dynamic> or <PPPoE> for the current network
connection status.
d
MAC(Ethernet)
Address
e
IP Address
f
Protocol
Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.
30_ network connection and setup
Item
Description
URL
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if
DDNS registration has failed.
h
IPv4
Scans for cameras with the IPv4 setting.
i
IPv6
Scans for cameras with the IPv6 setting.
Activated in an IPv6 compliant environment only.
j
Search
Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
k
l
m
Auto Set
The IP Installer automatically configures the network settings.
Manual Set
You should configure the network settings manually.
Exit
Exits the IP Installer program.
the IP installer, use only the installer version provided in the installation CD or use the latest one if
MM `` For
available. You can download the latest version from the Samsung web site (www.samsungcctv.com).
Static IP Setup
Manual Network Setup
Run <IP Installer_v2.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
MM `` For
support this function.
1. Select a camera in the search list.
Check the MAC address of the
camera on the camera’s label.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
The default values of <IP Address>,
<Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will
be displayed.
English _31
● network connection and setup
g
network connection and setup
3. In the <Address> pane, provide the
necessary information.
yy MAC (Ethernet) Address : The MAC
address imprinted on the camera
label is automatically displayed and
requires no user setting.
can configure the static IP settings
MM `` You
only if the DHCP checkbox is unchecked.
If not using a Broadband Router
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.
4. In the <Port> pane, provide necessary
information.
yy HTTP Port : Used to access the
camera using the Internet browser,
defaulted to 80.
yy VNP Port : Used to control the video
signal transfer, defaulted to 4520.
5. Enter the password.
Enter the password of “admin” account, which was used to access the camera.
The default password is “4321”.
default password can be exposed to a hacking thread so it is recommended to change the
JJ `` The
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
`` If you want to change the password, refer to “Administrator password change” of the user
setup. (page 88)
6. Click [OK].
Manual network setup will be completed.
32_ network connection and setup
If using a Broadband Router
settings may differ depending on the connected Broadband Router model.
MM `` The
For more information, refer to the user manual of the applicable router.
`` For more information about port forwarding of the broadband router, refer to “Port Range
Forward (Port Mapping) Setup”. (Page 36)
If the Broadband Router has more than one camera connected
Configure the IP related settings and the Port related settings distinctly with each other.
ex)
Category
Camera #1
Camera #2
IP related settings
IP Address
Subnet Mask
Gateway
192.168.1.100
255.255.255.0
192.168.1.1
192.168.1.101
255.255.255.0
192.168.1.1
Port related settings
HTTP Port
VNP Port
8080
4520
8081
4521
Port> is set other than 80, you must provide the <Port> number in the address bar
MM `` Ifofthethe<HTTP
Internet browser before you can access the camera.
ex) http://IP address : HTTP Port
http://192.168.1.100:8080
English _33
● network connection and setup
yy IP Address : Enter an address falling in
the IP range provided by the Broadband
Router.
ex) 192.168.1.2~254, 192.168.0.2~254,
192.168.XXX.2~254
yy Subnet Mask : The <Subnet Mask>
of the Broadband Router will be the
<Subnet Mask> of the camera.
yy Gateway : The <Local IP Address> of
the Broadband Router will be the <Gateway> of the camera.
network connection and setup
Auto Network Setup
Run <IP Installer_v2.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
MM `` For
support this function.
1. Select a camera in the search list.
Check the MAC address of the camera
on the camera’s label.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>,
and <Gateway> will be set automatically.
3. Enter the password.
Enter the password of “admin” account,
which was used to access the camera.
The default password is “4321”.
default password can be exposed to
JJ `` The
a hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related
issues caused by the unchanged
password shall be responsible for the
user.
`` If you want to change the password, refer to “Administrator password change” of the user
setup. (page 88)
4. Click [OK].
Auto network setup will be completed.
34_ network connection and setup
Dynamic IP Setup
Dynamic IP Environment Setup
Checking the Dynamic IP
1. Run the IP Installer on the user’s local
computer.
Cameras allocated with <Dynamic IP>
address are shown in the list.
2. Select a camera from the search result.
3. Click the [Manual Set] button and
check the camera’s <Dynamic IP>
address.
If you uncheck <DHCP>, you can
change IP to <Static>.
English _35
● network connection and setup
yy Example of the Dynamic IP environment
-- If a Broadband Router, with cameras connected, is assigned an IP address by the
DHCP server
-- If connecting the camera directly to modem using the DHCP protocols
-- If IPs are assigned by the internal DHCP server via the LAN
network connection and setup
Port Range Forward (Port Mapping) Setup
If you have installed a Broadband Router with a camera connected, you must set the port range
forwarding on the Broadband Router so that a remote PC can access the camera in it.
Manual Port Range Forwarding
1. From the Setup menu of the Broadband
Router, select <Applications &
Gaming> - <Port Range Forward>.
For setting the port range forward for
a third-party Broadband Router, refer
to the user guide of that Broadband
Router.
2. Select <TCP> and <UDP Port>
for each connected camera to the
Broadband Router.
Each port number for the Broadband
Router should match that specified in
<Setup> - <Network> - <Port> from
the camera’s web viewer menu.
3. When done, click [Save Settings].
Your settings will be saved.
MM `` Above sample instructions are based on the CISCO’s Broadband Router.
`` The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
36_ network connection and setup
Setting up Port Range Forward for several network cameras
When several network cameras are connected to one Broadband Router device, you
should forward the TCP 943 port of the router to the TCP 943 port of a connected camera.
yy TCP 943 port is a port for the Silverlight policy server of a camera.
yy You can set a rule of Port Forwarding on the Broadband Router device through its
configuration web page.
yy You cannot change the Silverlight policy server port of a camera.
yy You can change the ports of the camera except the policy server port through its
configuration web pages.
When Camera1 and Camera2 are connected to a router :
User

Internet

Start
943
3000
3001
4520
4521
8080
8081
Broadband Router
End
Protocol
943
TCP
3000
TCP/UDP
3001
TCP/UDP
4520
TCP/UDP
4521
TCP/UDP
8080
TCP/UDP
8081
TCP/UDP
IP Address
192.168.1.100
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101

Camera1 (192.168.1.100)
HTTP Port
8080
Device port
4520
RTSP Port
3000
Policy Server Port
943

Camera2 (192.168.1.101)
HTTP Port
8081
Device port
4521
RTSP Port
3001
Policy Server Port
943
English _37
● network connection and setup
don’t set properly the TCP 943 port of the router, you cannot get any video stream from the
JJ `` Ifwebyoupage
of the camera.
network connection and setup
Connecting to the Camera from a Shared Local PC
1. Run the IP Installer.
It will scan for connected cameras and
display them as a list.
2. Double-click a camera to access.
The Internet browser starts and
connects to the camera.
to the camera can also be gained by typing the camera’s IP address in the address bar of
MM `` Access
the Internet browser.
Connecting to the Camera from a Remote PC via
the Internet
Since using the IP Installer on a remote computer that is not in the Broadband Router’s network
cluster is not allowed, users can access cameras within a Broadband Router’s network by using
the camera’s DDNS URL.
1. Before you can access a camera in the Broadband Router network, you should have
set the port range forward for the Broadband Router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address
of the camera, or the IP address of the Broadband Router in the address bar.
ex) http://www.samsungipolis.com/[Product ID]
MM `` For registering the DDNS settings, refer to “Registering with DDNS”. (page 66)
38_ network connection and setup
web viewer
Connecting to the Camera
Normally, you would
1. Launch the Internet browser.
● web viewer
2. Type the IP address of the camera in
the address bar.
ex) • IP address (IPv4) : 192.168.1.100
 http://192.168.1.100
- the Login dialog should appear.
• IP address (IPv6) : 2001:230:abcd:
ffff:0000:0000:ffff:1111
 http://[2001:230:abcd:ffff:0000
:0000:ffff:1111] - the Login dialog
should appear.
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.1.100:HTTP Port number(8080)
 http://192.168.1.100:8080 - the Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
ex) URL address : http://www.samsungipolis.com/[Product ID]
- the Login dialog should appear.
English _39
web viewer
`` To check the DDNS address
If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE
modem, the IP address of your network will be changed each time you try to connect to
the ISP (Internet Service Provider) server.
If this is the case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check
the changed IP when you try to access the device.
To register your device to the <DDNS> server, visit www.samsungipolis.com and register
your device first, and then set the Web Viewer’s <Network> - <DDNS> to <Samsung
DDNS>, as well as providing <Product ID> that had been used for DDNS registration.
Login
Whenever you access the camera, the login window appears.
Enter the User ID and password to access the camera.
1. Enter “admin” in the <User Name>
input box.
The administrator ID, “admin”, is fixed
and can not be changed.
2. Enter “4321” in the <Password> input
box.
If the password is changed, enter the
changed password instead.
3. Click [OK].
If you have logged in successfully, you
will the Live Viewer screen.
default user ID is “admin”, and the
MM `` The
default password is “4321”.
`` For security purposes, ensure that you change the password in <System> - <User>.
`` The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
`` If you check the “Remember my password” option when your input is done, in future you will be
logged in automatically without being prompted to enter the login information.
will experience the best video quality if the screen size is 100%. Reducing the ratio may cut
JJ `` You
the image on the borders.
40_ web viewer
Installing Silverlight Runtime
`` To install on Windows OS
1. Click <Click Here>.
2. When the file download dialog pops up,
click <Run>.
3. When the download is completed, click
<Run>.
4. The Silverlight Runtime installation page
will be displayed. <Install now> to
proceed with the installation.
English _41
● web viewer
If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will
be redirected to the Silverlight Runtime installation page automatically when accessing the web
viewer.
web viewer
5. When done, click <Close>.
`` To install on MAC OS
1. Run the file trailing with “.dmg”.
2. Run the install package file automatically created, ending
with “.pkg”.
3. Click <Continue>.
42_ web viewer
4. Select your language on the language
selection screen, and click <Continue>.
● web viewer
5. Click <Agree>.
6. Click <Install>.
English _43
web viewer
7. Enter the password of the account
currently logged in, and click <Install
Software> and continue.
8. Once completed, click <Close>.
44_ web viewer
Installing STW WebViewer Plugin
If connecting to a camera for the first time, you will see the installation message. Then, install the
required WebViewer Plugin to access the camera and control the video from it in real time.
message of “There is no VC++ 2010 runtime installed. Please install the runtime library.” Run the
vcredist_x86.exe file which can be found from Samsung website at www.samsungcctv.com or
the provided installation CD. The vcredist_x86.exe file is installer program of Microsoft’s Visual
Studio 2010 redistributable package for 32-bit operating systems.
1. When accessing the start screen of
the monitoring page, click the yellow
warning message in the top of the
page.
2. Click <Run Add-on>.
3. The security warning popup appears,
click [Run].
4. When the Web viewer plug-in is
installed properly, you will see the live
screen displayed.
English _45
● web viewer
Visual C++ 2010 Redistribute Package should be installed on the PC before you can
MM `` Microsoft
install the Web viewer plug-in. If Visual Studio 2010 is not installed yet, you will see the error
web viewer
Using the Live Screen
a
b
c
d
e
f
g
h
i
j
k
l
Item
Description
a
b
c
Monitoring
Move to the monitoring screen.
Playback
Switch to the monitoring screen that plays recording data in the SD memory.
Setup
Move to the Setup screen.
d
Viewer Screen
e
Profile type
f
Screen
Optimization
g
Fix the resolution
46_ web viewer
Displays the Live video on the screen.
`` You can use the mouse wheel to activate the digital zooming in Viewer screen.
You can select a profile type in <Video profile> under the <Video & Audio> setup
menu.
`` When the Web Viewer is connected, the profile information currently using is
displayed.
The video size of the camera will switch to as big as the Web browser.
Regardless of the resolution setup configured in the camera, it sets the resolution to
640x480. Press it again to switch back to the default resolution.
Item
j
k
l
Full Screen
Switch the current video to the maximum size of the monitor.
Capture
Saves the snapshot as an image file in the .bmp or .jpg format.
Alarm output
Activate the Alarm Out port.
● web viewer
h
i
Description
Audio/Microphone
Enable/disable audio and microphone, and controls volume.
Control
Hide the context
menu
The left-corner context menu will disappear but only the menu icon.
To capture the snapshot
1. Click [Capture (
)] on the scene to
capture.
The Capture dialog should appear.
2. Confirm the save path and click [Save]
button.
The screenshot will be saved in the
specified path.
you encounter an interrupted video
MM `` Ifwhen
capturing the image with IE8 on a
Windows 7-based PC, deselect “Turn On
Protected Mode” from “Tools – Internet Options – Security”.
To fit the full screen
1. Click the [Full Screen (
)] button.
2. This will fit the Viewer to the full screen.
3. To exit the full screen mode, press [Esc] on the keyboard.
MM `` For the Internet Explorer and Google Chrome browser, you can switch to the full screen.
English _47
web viewer
To control the audio sound
1. Click [Audio (
2. Use [
)] icon to activate audio communication.
] bar to control the volume.
To control microphone
1. Click [Mic (
)] icon to activate the microphone.
Search and play by event
1. Click the [Playback (
)] button.
2. Specify the start time and end time of
your search.
3. Select an event type for your search
within the specified period.
4. Click the [Event search] button.
The search results will be displayed in
the list.
more than 500 events are recorded
MM `` Ifwithin
the search period, your search will
be limited up to the date when the 500th event is recorded.
For instance, if the search period is between 10th and 15th day of the month, and more than 500
events were recorded 10th through 11th, your search will be limited up to 11th day with a total of
500 events, and events after then (from 12th) will not be found.
5. Select a data item to play in the search
list.
6. Click the [Play (
)] button.
7. To stop playing the video, click
[Stop (
)].
8. To return to the search screen,
click [Exit (
)].
48_ web viewer
Search and play by time
1. Click [Time Search (
)].
● web viewer
2. Click a desired date in the calendar.
The video on the specified date will be
played.
3. If the video playback is stopped, select
a time and click [Play (
)].
The video on the selected time will be
played.
4. While the video is being played, the
recording time for the current video will
be shown.
5. Search for the video forward or backward, and control the play speed.
-- To control the play speed
If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will
increase accordingly.
If selecting (, the button will switch to x8, x4, x2, x1, and the play speed will
decrease accordingly.
-- To control the playback direction
If you see the ) button with the play speed displayed, the video will be played
forward; Whereas, if you see the ( button with the play speed displayed, the video
will be played backward.
6. Move [Time bar (
)] to a desired time point of the video before playing it.
The time containing a normal recoding file will be highlighted in blue; the time with
the event recording will be highlighted in red.
English _49
web viewer
To check time information of the playing video
1. Click the [About (
)] button.
2. Date and time information appears on the screen.
To back up the searched video
1. During playback, click [
] on the
scene to back up.
The scheduling window for backup
start and end time appears.
] button.
2. Click [
The Save As window appears.
3. Confirm the save path and click [Save]
button.
The screenshot will be backed up to
the specified path.
To play the backup video
The backup video will be saved in .avi format. The backup video can be played with any
media player supporting the format on your PC.
50_ web viewer
setup screen
Setup
You can configure the video & audio, network, event and system settings of the camera in the
network.
)].
Sliverlight 4.0 is required to be installed on the PC for setup pages that provide preview
JJ `` Microsoft
video.
If not installed already, automatically moves to the Sliverlight setup.
Video & Audio Setup
Video profile
1. From the Setup menu, select the
)> tab.
<Video & Audio (
2. Click <Video profile>.
3. Set the <Video Profile Connection
Policy>.
•• Keep connection when profile
setting is changed : Changing profile
properties that is used by existing
connection does not affect such
connection and remains with old
profile setup.
If not selected, changing a profile
used by an existing connection
resets such connection.
4. Select each profile properties.
5. Click the input box of each item and
enter / select a desired value.
`` The context menu may differ depending on
the selected codec type.
English _51
● setup screen
1. In the Live screen, click [Setup (
2. The Setup screen appears.
setup screen
•• Default profile : If no profile is selected when using the Web Viewer, the default
video profile is applied.
•• E-mail/FTP profile : Video profile to be transferred to the specified email or FTP
site.
`` Only the MJPEG codec can be set as the E-mail/FTP profile.
•• Record profile : This is the profile that is applied to video recording.
•• Audio-In : Sets whether to use audio for video recordings.
6. According to your situation, set ATC
(Auto Transmit Control) mode.
•• ATC mode : It adjusts the video
properties according to the variance
in the network bandwidth, controlling the bit rate. Adjusting the bit rate depends
on the ATC mode.
-- Control framerate : Reduce the frame rate if the network bandwidth drops down.
-- Control compression : Control the compression rate if the network bandwidth
drops down.
Compression adjustment can cause deterioration of the image quality.
`` If <Bitrate control> is set to <CBR>, the encoding priority according to the ATC mode will be
fixed as below:
Bitrate control / ATC mode
Control framerate
CBR
Framerate
Control compression
Compression
•• ATC sensitivity : Affect the transfer rate according to the variance in the network
bandwidth.
The transfer rate will be adjusted to the fastest if the bandwidth is <Very high>,
and adjusted to the latest if the bandwidth is <Very low>.
•• ATC limit : If the quality or frame rate is adjusted, the property will be changed to
the applied value (%) against the previous setting value (100%).
Note that if you reduce the property value too much, you may encounter flickering
on the screen. So it is advisable to adjust the value within the threshold.
JJ `` It is recommended to apply ATC control only for cameras supporting ATC.
`` Set the ATC sensitivity to <Very low> in a network environment with high variance in the network
bandwidth.
`` If the network connection is unstable, you may encounter flickering on the screen.
7. When done, click [Apply (
)].
MM `` MPEG-4 videos can not be stored in the SD memory.
52_ setup screen
To add a video profile
You can add as many codecs as necessary so that a variety of profiles can be applied
according to the recording condition.
2. Provide the name and select a codec.
3. Specify the conditions under which the codec will be applied.
4. Specify the details of the selected codec including resolution and frame rate.
Click <Advanced> to display the context menu.
•• Resolution : Set the video size of the MPEG-4, H.264, and MJPEG files.
•• Framerate : Specify the frame rate.
•• Compression : Specify the compression rate of the video.
•• Maximum bitrate : Specify the maximum bit rate of the video.
the bit rate can be adjusted limitedly according to the resolution, frame rate and screen
JJ `` Ascomplexity,
the actual bit rate can be greater than the maximum bit rate. So you must
consider the use conditions when setting the value.
•• Bitrate control : You can select one from constant bit rate and variable bit rate for
compression. Constant bit rate (CBR) varies the video quality and fixes network
transfer bit rate, while variable bit rate emphasizes the quality by varying network
transfer bit rate.
•• Encoding priority : You can set the video transfer method to Framerate or
Compression.
•• GOV length : Select a GOV length between 1 and 150.
•• Profile : You can select the H.264 profiling method.
•• Entropy coding : Reduce the possible compression loss due to encoding.
•• Multicast(SVNP) : Specify the use of the SVNP protocol.
-- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.
-- Port : Specify the video communication port.
-- TTL : Set the TTL for the SVNP packet.
•• Multicast(RTP) : Specify the use of the RTP protocol.
-- IP address : Enter an IPv4 address with which you can connect to the IPv4
network.
-- Port : Specify the video communication port.
-- TTL : You can set the TTL for the RTP packet.
English _53
● setup screen
1. Select one from the <Video profile> options.
setup screen
What is GOV length?
GOV(Group of Video object planes) is a set of video frames for MPEG-4 and H.264
compression, indicating a collection of frames from the initial I-Frame (key frame) to the next
I-Frame. GOV consists of 2 kinds of frames: I-Frame and P-Frame.
I-Frame is the basic frame for the compression, also known as Key Frame, which contains
one complete image data. P-Frame contains only the data that has changed from the
preceding I-Frame.
You can specify a value between 1 and 150 for the MPEG-4 and H.264 CODEC.
Video setup
1. From the Setup menu, select the
<Video & Audio (
)> tab.
2. Click <Video setup>.
3. Select a <Video source> mode.
•• Flip mode : Turn upside down
the image that is captured by the
camera.
•• Mirror mode : Flip horizontal the
image that is captured by the
camera.
4. Set the <Video output>.
-- If you select <Off>, the video signal
will not be output via the VIDEO OUT
port.
5. Select the video type.
6. Specify the privacy zone.
7. When done, click [Apply (
54_ setup screen
)].
To set the privacy zone
You can specify a certain area of the camera video to be protected for your privacy.
1. Set it to <On>.
2. When done, click [Apply (
)].
● setup screen
3. Specify the <Color> that will fill the
privacy area.
4. Click on the video screen and drag to
set the desired area.
5. Provide a name and press [OK].
6. If you want to delete an area in the list,
select one and click [Delete (
)].
Audio setup
You can configure the I/O settings of the audio source from the camera.
1. From the Setup menu, select the
<Video & Audio (
)> tab.
2. Click <Audio setup>.
3. Set the audio input level.
•• Gain : Sets the input audio gain.
4. Set the audio output level.
•• Enable : Sets whether to use audio
output.
•• Gain : Sets the output audio gain.
5. When done, click [Apply (
)].
English _55
setup screen
Camera setup
You can change the camera settings according to the environment where the camera is
located.
1. From the Setup menu, select the
<Video & Audio (
)> tab.
2. Click <Camera setup>.
3. Configure the settings as necessary of :
SSDR, White balance, Backlight,
Exposure, Special, OSD, Time OSD,
IR mode
)].
4. When done, click [Apply (
`` If a certain time (timeout: 240s) is elapsed with
your not pressing the [Apply (
)]
button after changing the settings, your
changes will not be applied.
SSDR (Samsung Super Dynamic Range) Setup
In a scene where the difference between bright and dark is severe, you can increase the
brightness of the dark area alone to regulate the overall brightness.
1. Select <SSDR>.
2. Set <Mode> to <On>.
3. Configure the <Level> and <D-Range>
settings as necessary.
•• Level : Adjust the level of the
dynamic range.
•• D-Range : Select the amplitude area of the dynamic range.
56_ setup screen
White balance Setup
You can correct the image colors based on white under any lighting conditions.
1. Select <White balance>.
AWC mode, click the [AWC Set] button if you want to keep the white balance level of the
MM `` Incurrent
image.
white balancing may not work properly in the following conditions:
JJ `` The
If this is the case, switch to AWC mode.
-- If the surrounding condition of the object is out of the temperature correction range
ex) Clear sky, sunset
-- If the surrounding of the object is dark
-- If the focus of the camera directly faces the florescent lighting or if the camera is installed in a
place of variable illumination, the white balancing operation may be unstable.
English _57
● setup screen
2. Select <Mode>.
•• ATW : Corrects the colors of the
camera video automatically.
•• Manual : You can adjust the red and
blue gains of the camera video manually.
•• AWC : Corrects the colors of the camera video to be optimized to the current
lighting condition and screen mode.
To obtain the optimal condition for the current lighting, put the focus of the camera
to a white paper and press the [AWC Set] button. If the lighting environment is
changed, you should readjust the settings accordingly.
•• Outdoor : Automatically corrects the video colors of the camera to be optimized
to the outdoor environment.
•• Indoor : Automatically corrects the video colors of the camera to be optimized to
the indoor environment.
setup screen
BLC Setup
You can specify a desired area on the video manually and set the area to be displayed
more clearly.
1. Select <Backlight>.
2. Set <Mode> to <BLC>.
3. Set <BLC level>.
You can change the level to adjust the
brightness of the monitoring area.
4. Set the <Top, Bottom, Left, Right>
levels to specify the target area.
HLC (Highlight Compensation) Setup
When a strong light such as streetlamp or headlight faces forward to the camera, you can
mask that exposed area in order to protect it from being saturated.
1. Select <Backlight>.
2. Set <Mode> to <HLC>.
3. Set the <HLC level> and the <Mask
tone>.
•• HLC level : Adjust the brightness
level so as to remove the incoming
highlight from a specific condition.
•• Mask tone : Adjust the mask tone of
the highlighted area.
this function will be activated only if the incoming highlight exceeds a certain
MM `` Atareanightin aoperation,
low contrast environment.
`` At night, HLC will not function if the scene is either too bright or too dark.
`` The backlight function is not available while in IR mode.
58_ setup screen
Exposure Setup
You can adjust the exposure level of the camera.
1. Select <Exposure>.
`` The greater the Sens-Up factor is, the brighter the screen becomes but it may result in an
afterimage or video delay.
•• Sens-up limit : Set the work condition to Auto mode in a low contrast scene.
•• Iris : You can set the camera iris to Auto or Manual to your preference.
-- Auto : Automatically sets the iris adaptively to the ambient lighting and shutter
speed.
-- Manual : Sets the iris to its maximum aperture.
•• AGC mode : Select AGC Control mode.
Adjust the gain value of the video (that, in particular, was recorded at a low
contrast scene and had a lower brightness level than normal) to control the video
brightness.
English _59
● setup screen
2. Select each item and set it properly.
•• Brightness : Adjust the screen
brightness.
•• Shutter mode : Adjust the electronic
shutter of the camera.
-- ESC (Electronic shutter control) :
Adjust the shutter speed
automatically according to the
ambient brightness.
-- Manual : Adjust the shutter speed of the camera manually.
-- A.FLK (Anti flicker) : Select this feature if you encounter a flickering screen due
to a frequency mismatch with the ambient lighting.
•• Shutter speed : Control the shutter speed manually.
•• SSNR3 : Specify the use of noise reduction.
•• SSNR3 level : Adjust the noise reduction level.
•• Sens-up mode : Automatically senses the darkness level at night or in a low
contrast scene and extends the accumulation time accordingly for a bright and
sharp image.
`` If you set the shutter mode to Manual/A.FLK, SENS-UP mode will be deactivated.
setup screen
Special Setup
1. Select <Special>.
2. Select each item and set it properly.
•• Day & night : You can switch the
mode to adjust the black and white
level as well as the colors.
-- Color : Always displays the video in
colors.
-- B/W : Always displays the video in
black and white.
-- Auto : Displays in color mode
during normal daytime and switches to black and white mode in a low contrast
scene at night.
`` If you set the AGC mode to <Off> from <Exposure>, the AUTO DAY/NIGHT mode will be
disabled accordingly.
-- External B/W : Control the image modes of Color and B/W when an external IR
is synchronized via the Alarm In port.
•• Dwell time : This is the time while each applicable lighting condition is kept in
order to enable the switch between day and night modes.
•• Duration : Specify the time interval of lighting at which the sequence operation is
triggered.
•• Simple focus after D/N : When switching day/night mode, automatically runs
focus adjustment.
When using IR lens with the camera, set this to <Off>.
<Simple focus after D/N> option may cause false focus adjustment under a specific
MM `` Setting
condition. For further details, refer to “Focus setup”. (Page 62)
•• Sharpness mode : Adjust the overall sharpness of the image.
If selecting <On>, you can adjust the sharpness of the image.
•• Sharpness level : The higher the level is, the sharper and clearer the outline of the
image becomes.
•• Gamma : Adjust the contrast of the image.
•• Color level : Adjust the color level of the image.
•• Alarm in : Set the image to Color or B/W depending on the Open/Close state of
the alarm sensor.
`` If the Day & Night mode is set to External B/W, the alarm-in function of the event-alarm input page
will be disabled.
60_ setup screen
OSD Setup
1. Select <OSD>.
•• Camera title position X, Y : Specify the coordinates where the camera title is
displayed on the screen.
Time OSD Setup
1. Select <Time OSD>.
2. Select each item and set it properly.
•• Time display : Specify the use of time
display on the screen.
•• Date format : Specify the date format
that will be displayed on the screen.
•• Time position display X, Y : Specify the position of time display on the screen.
•• Display weekday : Specify the use of date display date on the screen.
IR Mode Setup
1. Select <IR Mode>.
2. Select each item and set it properly.
•• IR Mode : When the IR indicator
turns on in B/W mode, the screen
will be protected from saturation on
the center area so that you can identify a short-distant object.
-- Off : IR mode will be disabled.
-- Auto : Adjust the IR brightness according to the brightness of the object on the
center screen.
-- Manual : Adjust the IR brightness manually.
•• Level : If you set IR mode to Manual, you can adjust the brightness level of the IR
indicator to between 0 and 32.
MM `` IR mode will be activated when <Day & night> is set to <Auto> or <B/W>.
English _61
● setup screen
2. Select each item and set it properly.
•• Camera title : Specify whether or
not to display the camera title on the
screen.
`` You can enter up to 15 characters for the title.
setup screen
Focus setup
You can adjust the focus and zoom ratio of video image.
1. From the Setup menu, select the
<Video & Audio (
)> tab.
2. Click <Focus setup>.
3. Set the focus and zoom.
•• Focus : Manually adjusts the lens
focus (Far <-> Near).
•• Zoom : Manually adjusts the zooming
(Wide <-> Tele).
•• Simple focus : Click [ ] button to fit
the focus automatically.
Simple focus mode may not fit
JJ `` The
correctly in the following cases:
-- Sudden change to the object in Simple focus mode (sudden movement, appearance or
disappearance)
-- Radical change to the brightness in Simple focus mode
-- Image of a low contrast
-- If the camera is exposed to a strong light source in the front or surroundings
`` In case the focus is inappropriate apart from mentioned above, use [
,
,
,
,
] button to manually adjust the focus.
`` In a situation where Simple focus is hardly applied, try to use the manual focus mode.
62_ setup screen
,
Network Setup
Interface
2. Click <Interface>.
3. Set the <Interface>.
•• IP type : Select an IP connection type.
-- Manual : Specify the IP address,
Subnet mask, Gateway, DNS1,
and DNS2.
-- DHCP : Specify the DNS1 and
DNS2.
-- PPPoE : Specify the DNS1, DNS2,
ID and Password.
`` If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.
•• MAC address : Shows the MAC address.
•• IP address : Displays the current IP address.
•• Subnet mask : Displays the <Subnet mask> for the set IP.
•• Gateway : Displays the <Gateway> for the set IP.
•• DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
4. Set the <IPv6 setup>.
`` Set to <Use> to use IPv6 address.
•• Default : Use the default IPv6 address.
•• DHCP : Display and use the IPv6 address obtained from the DHCP server.
•• Manual : Enter IP address and gateway manually and use it.
5. When done, click [Apply (
)].
IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous
JJ `` The
settings will be restored automatically.
`` Once completed with editing, click [Apply (
After a while, connect again with the changed IP.
)] to apply changes and the browser exits.
English _63
● setup screen
1. From the Setup menu, select the
<Network (
)> tab.
setup screen
Port
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <Port>.
3. Type in each item in the Port menu as
necessary.
`` Neither the port range between 0 and 1023
nor port 3702 is available.
•• HTTP port : HTTP port used to
access the camera via the web browser.
The default is 80(TCP).
`` Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security
policy.
•• Device port : Set a port used to transfer video signals with the Samsung
protocols.
•• RTSP port : Used to transfer videos in the RTSP mode; the default is 554.
•• Web streaming port : Used to transfer videos to the Web Viewer; the default is 4520.
•• Silverlight policy port : Silverlight is used to permit to acquire a network
connection; the default is 943.
changed the HTTP port, the browser exits.
MM `` IfAfterwards,
address should contain the newly assigned HTTP port trailing the IP.
ex) IP address: 192.168.1.100, HTTP port : Assigned 8080  http://192.168.1.100:8080
(If HTTP port is set to 80, no need to specify the port number)
`` The port range of the Web Streaming is between 4502 and 4534. If the Device port is with this
effective range, the Web Streaming port should be specified the same as the Device port.
`` You cannot change the Web Streaming/Silverlight policy server port of a camera.
4. When done, click [Apply (
64_ setup screen
)].
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of
a camera into a general Host Name so that the user can easily remember it.
2. Click <DDNS>.
3. Select the <DDNS> connection type.
4. Type in the DDNS items according to
the selected type.
•• Samsung DDNS : Select this if you
use the DDNS server provided by
Samsung Techwin.
-- Product ID : Enter the product ID that is registered with the Samsung DDNS
service.
-- Quick connect : It sets port forwarding automatically when used with a UPnP
(Universal Plug and Play) supporting router.
•• Public DDNS : Select one of provided public DDNS servers when you use a public
DDNS server.
-- Service : Select desired public DDNS service server.
-- Host name : Enter the name of the host that is registered with the DDNS server.
-- User name : Enter the user name for the DDNS service.
-- Password : Enter the password for the DDNS service.
5. When done, click [Apply (
)].
JJ `` If selected <Quick connect>, be sure to select Samsung DDNS service.
English _65
● setup screen
1. From the Setup menu, select the
<Network (
)> tab.
setup screen
Registering with DDNS
To register your product with the Samsung DDNS
1. Visit the iPOLiS web site
(www.samsungipolis.com) and sign in
with a registered account.
2. From the top menu bar, select <DDNS
SERVICE> - <MY DDNS>.
3. Click [PRODUCT REGISTRATION].
4. Enter the product ID.
`` You must perform the duplicate check for the
ID that you entered.
5. Select a <CLASSIFICATION> and
specify the <MODEL NUMBER>.
6. Specify the product location with a
description if necessary.
7. Click [REGISTRATION].
The product will be added to the
product list that you can check.
66_ setup screen
To connect to the Samsung DDNS in camera setup
1. From the DDNS setup page, set
<DDNS> to <Samsung DDNS>.
● setup screen
2. Provide the <Product ID> that you
registered product ID with the DDNS
site.
)].
3. Click [Apply (
When the connection is successfully
made, you will see the message of
<(Success)> on the screen.
Configuring public DDNS in Camera Settings
1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.
2. Enter the corresponding site’s host name, user name and password.
)] button.
3. Click [Apply (
If the connection properly establishes, <(Success)> appears.
4. When done, click [Apply (
)].
use DDNS service properly, both DDNS setup and the router’s port forwarding setup are
MM `` Torequired.
For port forwarding setup, refer to “Port Range Forward (Port Mapping) Setup”. (page 36)
English _67
setup screen
IP filtering
You can create a list of IPs that you want to grant or deny access to them.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <IP filtering>.
3. Select <Filtering type>.
•• Deny : If selecting this, access from
those IPs that are added to the
filtering will be restricted.
•• Allow : If selecting this, access from
only those IPs that are added to the
filtering will be accepted.
4. Click the [Add (
)] button.
The IP list will be created.
5. Provide the IP that you want to grant or deny access from.
When you enter an IP address and a Prefix, the list of IP addresses available will
appear in the right-side filter range column.
<Allow> for IP Filtering and <IPv6 setup> of <Interface> is set to <Use>, both IPv4
MM `` Ifandselected
IPv6 addresses of the computer currently configuring should be assigned.
`` The IP address of the computer used for the current setup cannot be added to <Deny>, it should
be added to <Allow>.
`` Only the IP addresses that are set to <Use> will be displayed in the filter column.
6. Select an IP to delete from the list.
)] button.
Click the [Delete (
7. When done, click [Apply (
68_ setup screen
)].
SSL
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the
<Network (
)> tab.
● setup screen
2. Click <SSL>.
3. Select a secure connection system.
`` To access the camera using HTTPS mode, you
have to type the IP address for the camera in
the form of “https://<Camera_IP>”.
If you failed to configure the Web viewer
settings in HTTPS mode with Internet Explorer,
edit the Internet options as follows: <Menu  Tools  Internet Options  Advanced  Security 
Uncheck TLS 1.0, and check TLS 1.1, TLS 1.2>
4. Search for the public certificate that you want to install on the camera.
To install the certificate on the camera, you need to provide a certificate name (it
can be arbitrarily assigned by the user), certificate file issued from the certification
authority and a key file.
`` The <HTTPS (Secure connection mode using the public certificate)> item will be active only if
there exists a public certificate installed.
5. When done, click [Apply (
)].
Installing the certificate
1. Enter the certificate name.
2. Select the certificate file to be installed and certificate key, and click [Install (
button.
)]
Deleting the certificate
1. Click [Delete (
)] button.
2. To delete a public certificate, you should access the network video decoder in
the mode of <HTTP (Do not use secure connection)> or <HTTPS (Secure
connection mode using a unique certificate)>.
English _69
setup screen
802.1x
When connecting network, you can choose whether using 802.1x protocol, and then install
the certification.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <802.1x>.
3. Set the <IEEE 802.1x setting(EAPOL
using EAP-TLS)>.
•• Enable IEEE 802.1x : Specify the use
of the 802.1x protocol.
•• EAPOL version : Select version 1 or 2.
•• ID : Enter the client certificate ID.
•• Password : Enter the client private
key password. If the key file used is not encrypted, you don’t need to enter it.
the connected network device does not support the 802.1x protocol, the protocol will not
JJ `` Ifoperate
properly even if you set it.
4. Install/remove the certificate.
•• CA certificates : Select a public certificate that contains the public key.
•• Client certificate : Select a public certificate that contains the client certificate key.
•• Client private key : Select a public certificate that contains the client private key.
5. When done, click [Apply (
)].
To install/remove 802.1x related certificates
1. Press the [Browse (
)] button for each item and select a certificate to install.
2. If no certificate is installed, you will see “Not Available” appearing next to the selected
item.
3. Press the [Install (
next to the item.
4. Press the [Delete (
70_ setup screen
)] button to start installation with a message of “Installed”
)] button to remove the certificate.
QoS
You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the
<Network (
)> tab.
● setup screen
2. Click <QoS>.
)] button.
3. Click the [Add (
The IP list will be created.
4. Enter an IP address to which you will
apply QoS.
default prefix for IPv4 is 32;
MM `` The
For DSCP, the default is set to 63.
`` Only the IP addresses that are set to <Use> can be prioritized.
5. Select an IP to delete from the list.
)] button.
Click the [Delete (
6. When done, click [Apply (
)].
SNMP
With the SNMP protocols, the system or network admin can monitor the network devices
on a remote site, and configure the environment settings.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <SNMP>.
3. Specify the <SNMP>.
•• Enable SNMP v1 : SNMP version 1
will be active.
•• Enable SNMP v2c : SNMP version 2
will be active.
-- Read community : Provide the
name of the read community where you can access to the SNMP information.
The default name is <public>.
-- Write community : Provide the name of the write community where you can
access to the SNMP information. The default name is <write>.
English _71
setup screen
•• Enable SNMP v3 : SNMP version 3 will be active.
-- Password : Specify the default password for SNMP version 3. The default
password is <admin4321>.
`` The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
`` Password should be longer than 8 characters, no more than 16 characters.
4. When done, click [Apply (
)].
v3 is only able to be set when the secure connection mode is HTTPS.
JJ `` SNMP
Refer to “SSL”. (page 69)
Event Setup
FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images taken
with camera to your PC if an event occurs.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <FTP / E-mail>.
3. Select <FTP configuration> or
<E-mail configuration> and enter /
select a desired value.
•• FTP configuration
-- Server address : Enter the IP
address of the FTP server that you
transfer the alarm or event images
to.
-- ID : Enter the user ID with which
you will log in to the FTP server.
-- Password : Enter the user account
password for logging into the FTP server.
-- Upload directory : Specify the FTP path where you will transfer the alarm or
event images.
72_ setup screen
4. When done, click [Apply (
)].
English _73
● setup screen
-- Port : The default port of the FTP server is 21; however, you can use a different
port number according to the FTP server settings.
-- Passive mode : Select <On> if you need to connect in passive mode due to the
firewall or the FTP server settings.
•• E-mail configuration
-- Server address : Enter the IP address of the email server that you transfer the
alarm or event images to.
-- Use authentication : Select whether to use authorization.
-- Use SSL : Specify the use of SSL.
-- ID : Enter the user ID for logging into the email server.
-- Password : Enter the user account password for logging into the email server.
-- Port : The default port of the email server is 25; however, you can use a different
port number according to the email server settings.
-- Recipient : Enter the address of the email recipient.
-- Sender : Enter the address of the email sender. If the sender address is
incorrect, the email from the sender may be classified as SPAM by the email
server and thus may not be sent.
-- Subject : Enter a subject for your email.
-- Body : Provide the text for the massage. Attach the alarm or event images to
the email that you are preparing.
setup screen
Storage
You can set the record conditions or the use of recording for the SD memory, check the
size of stored data, or format the SD memory itself.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Storage>.
To make recording on the SD memory
1. Check the memory card’s <Free> size
and <Total> size.
2. If there are sufficient free space, set the
device to <On>.
Otherwise, check the stored data and if
you find them not important, then click
<Format> to format the SD memory.
`` If your SD memory card writes slowly, only one frame per second will be stored.
`` For a SD memory card with a large capacity, the formatting will be slowed down accordingly.
`` Setting to higher options of resolution, bit rate and frame rate increases the amount of data produced.
As the size of data grows, transferred video can be stored only at 1 fps even if you set the record
quality to full frames.
3. Specify the storage action.
•• Record profile : Shows recording profile’s codec type.
•• Overwrite : If the SD memory is full, this will delete old data and store new data in
replacement.
•• Pre-alarm duration : Specify the time point before the occurrence of the alarm;
starting from the time point, the images will be transferred. You can specify up to
5 seconds before the occurrence of the alarm.
•• Post-alarm duration : Specify the time point after the occurrence of the alarm; to
the specified time point, the images will be transferred. You can specify up to 120
seconds after the occurrence of the alarm.
•• Normal : Make recording at a certain frame rate.
•• Event : Set the recording type for a certain event that occurs.
4. Specify the <Normal record setup>.
•• Always : Always save recorded video in the SD memory card.
`` If set to Always, the activation time cannot be changed.
•• Only scheduled time : Records only on the specified time of the specified day of week.
)] : Reset all settings.
•• [Clear (
5. When done, click [Apply (
74_ setup screen
)].
Alarm input
You can set the alarm input type, activation time, and operation mode.
1. From the Setup menu, select the
<Event (
)> tab.
● setup screen
2. Click <Event setup>.
3. Select <Alarm input> from <Event
action setup>.
4. Set whether or not to <Enable>.
5. Specify an input device.
•• Type
-- Normal open : It is normally open,
but if it is closed, an alarm will be
triggered.
-- Normal close : It is normally closed,
but if it is open, an alarm will be
triggered.
6. Specify the <Activation time>.
•• Always : Always check if an alarm occurs. It activates in operated mode when the
alarm occurs.
`` If set to <Always>, the activation time cannot be changed.
•• Only scheduled time : Check if an alarm occurs at a specified day of the week for
a specified time period. It activates in operated mode when the alarm occurs.
•• [Clear (
)] : Reset all settings.
7. Specify an operation that will perform if an alarm occurs.
•• FTP : Specify the use of FTP transfer in the alarm input setup.
•• E-mail : Specify the use of email transfer in the alarm input setup.
•• Record : Specify the use of recording in the alarm input setup.
•• Alarm output : Select whether to set the alarm output if an alarm is incoming, and
specify the alarm output time.
8. When done, click [Apply (
)].
English _75
setup screen
Time schedule
You can set to save the video data at a certain interval as scheduled regardless of the
actual occurrence of the event.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Event setup>.
3. Select <Time schedule> from <Event
action setup>.
4. Set whether or not to <Enable>.
5. Specify the <Transfer interval>.
6. Specify the <Activation time>.
•• Always : Always activates in operated
mode at the set interval.
•• Only scheduled time : Periodically
activates in operated mode at a
specified time and date.
7. Specify the activation conditions.
•• FTP : Specify the use of the FTP transfer if an event occurs.
8. When done, click [Apply (
76_ setup screen
)].
Tampering detection
You can set to detect tampering attempts and trigger events, such as sudden change
of camera’s framing direction, blocked lens and other overall change of scenes from the
video.
● setup screen
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Event setup>.
3. Select <Tampering detection> from
<Event action setup>.
4. Set whether or not to <Enable>.
5. Set the tampering detection sensitivity.
The higher the sensitivity, detects the
minutest tampering attempts.
6. Specify the activation time and
activation condition.
`` For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 75)
7. When done, click [Apply (
)].
JJ `` The default tampering detection function may not work properly in the following cases:
-- Under circumstances of simple background or low illumination and night time may lower the
detection sensitivity.
-- A severe shaking of the camera or a drastic change to the illumination can be considered a
tampering by mistake.
-- Detection of the tampering may take some time (maximum 5 seconds) right after the
tampering was made.
-- Once a tampering is detected, the camera will resume a normal operating after a certain
stability time (approx. 5 seconds) during which no detection will be performed.
English _77
setup screen
Motion detection / Video analytics
Events of motion detection and video analysis can be set to trigger event signal output.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Event setup>.
3. Select <Motion detection / Video
analytics> from <Event action
setup>.
4. Set whether or not to <Enable>.
5. According to your purpose, select from
motion detection and intelligent video
analysis.
6. Set <Sensitivity>, <Size> and <Area>.
When selected Intelligent Video
Analysis, set <Analytics> too.
7. Set whether to use <Detection result
overlay>.
When a motion is detected, its size and
position is marked with a rectangle on
the screen.
•• Green : All targets detected as
moving.
•• Red : All targets detected as passing,
entering or exiting.
(Colored marking remains for 1 ~ 2
seconds.)
•• Blue : All targets detected as Appear/Disappear event.
(Colored marking remains for 3 ~ 5 seconds.)
8. Specify the activation time and activation condition.
`` For more information about <Activation time> and <Action>, refer to “Alarm input”. (page 75)
9. When done, click [Apply (
78_ setup screen
)].
detection and Video analytics cannot be used simultaneously.
JJ ```` Motion
When setting the area for motion detection and video analysis, note that the top and bottom
screen border areas (up to 14-pixel height for the top border, up to 20-pixel height for the bottom
border) will be excluded from detection/analysis.
``
``
``
``
``
detected.
Set the maximum and minimum detection size appropriately to objects to be detected.
Detected size of an object may have difference with the actual size according to its shape.
Up to 16 objects from the top side of the screen can be displayed.
If camera is capturing a close object, the video analysis capability may degrade.
In the following cases, motion detection and intelligent video analysis function may be degraded
or cause improper detection.
-- The object color or brightness is similar to the background.
-- Small activities around the border area of the camera’s field of view.
-- Multiple movements continue occurring at random due to a scene change, rapid lighting
changes or other reasons.
-- A fixed object continues moving in the same position.
-- Motions of less position changing such as approaching to the camera or fading away from the
camera.
Moving object approaches to the camera too close
An object hides other objects behind.
Two or more objects overlap or one object divides in multiple portions.
Too fast object (for a proper detection, one object should be found overlapping between
contiguous frames).
-- Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp.
-- In severe snow, rain, wind or in dawn / dusk.
-----
English _79
● setup screen
`` Before using, set the minimum and maximum motion sizes to suit desired motion range to be
setup screen
To use Motion detection
It detects a motion that meets all conditions specified by sensitivity, size and area.
1. Select a motion detection mode.
2. Select <Sensitivity> tab to set the
sensitivity level. You can set the sensor’s
sensitivity to detect a motion out of the
background from the monitoring video.
a situation that definitely distinguishes
JJ `` Inobjects
out of backgrounds, set this to
a low sensitivity level. For opposite case
that is hard to distinguish objects like low
illuminated situation, set this to a high
level.
3. Select <Size> tab.
You can limit the minimum/maximum
size of motion to be detected.
•• Minimum Size : To set the minimum
size of detected motions, select
<Minimum Size> and then point
and drag to the desired size on the
screen using the mouse.
•• Maximum Size : To set the maximum
size of detected motions, select
<Maximum Size> and then point
and drag to the desired size on the
screen with your mouse.
smaller than the specified minimum size or bigger than the maximum size are not
JJ `` Motions
detected. To avoid unintended detections caused by great and small noises, set minimum/
maximum motion sizes appropriately in accordance to your environments.
Note that same motions on the same location can be differently detected in their detection size;
it is recommended to consider and include the tolerable difference when setting the minimum/
maximum detection sizes.
80_ setup screen
● setup screen
4. Select <Area> tab.
You can specify an area on the screen
to include or exclude the area to/from
detection.
You can specify up to 4 areas.
•• Detection area : Sets the entire
screen as excluded from detection,
and adds specified area as motion
detection area. Use your mouse to
drag to specify preferred area as the
motion detection area.
•• Non detection area : Sets the entire
screen as motion detection area, and
excludes specified area as not to be
detected. Use your mouse to drag
to specify preferred area as the non
detection area.
5. To delete an area, right click on the
screen to open popup context menu
and select Delete, and [OK] button.
JJ `` All areas defined are deleted.
6. When done, click [Apply (
)].
English _81
setup screen
To use Video analytics
It detects event that meets all conditions specified by sensitivity, size and area and the
event condition rules.
1. Select the video analysis mode.
2. Set <Sensitivity>, <Size> and <Area>.
For further details on settings, refer
to “To use Motion detection”. (Page
80~81)
3. Select <Analytics> tab.
4. Select the video analysis type.
•• Passing, Entering/Exiting : Detects
motions of passing, entering into or
exiting from a virtual line specified by
the user.
•• Appearing (Disappearing) : Detects
motions of appearing on or
disappearing from the user-defined
area or the entire screen area.
5. Set the video analysis rules.
For further details on settings, refer to
“To set the video analysis rules”.
(page 83~84)
6. Set whether to use <Detection result
overlay>.
Specified rules of virtual lines and areas
are displayed on the monitoring page.
7. When done, click [Apply (
82_ setup screen
)].
To set the video analysis rules
`` Passing
● setup screen
1. Set the type to <Passing, Entering/
Exiting>.
2. Set the event rule to <Virtual line
based rules>.
3. On the screen, click on preferred
starting and ending point of the virtual
line, then a popup window appears.
4. Select the desired rule:
•• Right : Detects motions of moving
from the left to the right, over the
virtual line.
•• Left : Detects motions of moving
from the right to the left, over the virtual line.
5. Click [OK].
6. To remove a defined rule, right click on the displayed virtual line to open popup
context menu and select [Delete] button.
`` Entering/Exiting
1. Set the type to <Passing, Entering/
Exiting>.
2. Set the event rule to <Defined area
based rules>.
3. On the screen, click four vertices to
define detection area and a popup
window appears.
4. Select the desired rule:
•• Entering : Detects motions of moving
object whose center point entering
into the defined area, from outside of
the area.
•• Exiting : Detects motions of moving object whose center point exiting from the
defined area, from inside of the area to outside.
5. Click [OK].
6. To remove a defined rule, right click on the displayed side lines of the area to open
popup context menu and select [Delete] button.
English _83
setup screen
`` Appearing (Disappearing)
1. Set the analysis type to <Appearing
(Disappearing)>.
2. Select the desired event rule:
•• Defined area based rules : It detects
event of appearing object that
appears in the area and remaining
for a certain time period while not
passing through the area borders,
and opposite case of disappearing of
objects existed in the area.
On the screen, click four vertices to
define detection area.
Select the [Appearing
(Disappearing)] from the popup.
•• Entire area based rules : It detects
event of appearing object that
appears in the entire screen and
remaining for a certain time period,
and opposite case of disappearing of
objects existed in the screen.
Right click on the screen to open
the popup context menu and select
[Appearing(Disappearing)].
3. Click [OK].
4. To remove a defined rule, right click on
the displayed side lines of the area or
on the screen to open popup context
menu and select [Delete] button.
84_ setup screen
Network disconnection
You can receive and save events of a physically disconnected network.
1. From the Setup menu, select the
<Event (
)> tab.
● setup screen
2. Click <Event setup>.
3. Select <Network disconnection> from
<Event action setup>.
4. Set whether or not to <Enable>.
5. Specify the activation time and
activation condition.
`` For more information about <Activation
time> and <Action>, refer to “Alarm input”.
(page 75)
6. When done, click [Apply (
)].
Alarm output setup
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Alarm output setup>.
3. Set the camera’s type of alarm output.
`` If you change the alarm output type, the alarm
out button on the monitoring page and alarm
output type displayed on Event Setup page will
be changed accordingly.
•• Type
-- Normal open : Considers “Open circuit” status of the sensor or alarm input device
as normal, and triggers alarm event if becomes “Closed circuit” status.
-- Normal close : Considers “Closed circuit” status of the sensor or alarm input device
as normal, and triggers alarm event if becomes “Open circuit” status.
English _85
setup screen
4. Set the alarm output button.
•• Mode : Sets the alarm output method.
`` There is difference between operations when clicked alarm output button while disabled.
-- Pulse : It is activated during the time period specified by the duration (switching
interval) and then becomes inactive automatically.
-- Active/Inactive : It maintains as activated until the user clicks the button again to
make it inactive.
•• Duration : Set the alarm duration that maintains activated if the mode is set to
pulse, from 1 to 15 seconds.
5. When done, click [Apply (
)].
System Setup
Product information
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Product information>.
3. Check the camera information, or
provide details according to your
network environment.
•• Model : Model name of the product.
•• Serial number : Product serial number.
•• Device name : Provide a device name that will be displayed on the Live screen.
•• Location : Specify the location where the camera is installed.
•• Description : Provide detailed information about the camera location.
•• Memo : Provide an explanation about the camera for better understanding.
•• Language : Select a preferred language for the Web Viewer OSD.
MM `` The default language is set to <English>.
4. When done, click [Apply (
86_ setup screen
)].
Date & Time
1. From the Setup menu, select the
<System (
)> tab.
3. Specify the time and date that will be
applied to the camera.
•• Current system time : Displays the
current time settings of your system.
•• Timezone : Specify the local time
zone based on the GMT.
•• Use daylight saving time :
If checked, the time will be set one
hour before the local time zone for
the specified time period.
This option will be displayed only in
areas where DST is applied.
•• System time setup : Specify the time and date that will be applied to your system.
-- Manual : Specify the time manually.
-- Synchronize with NTP server : Sync with the time of the specified server address.
-- Synchronize with PC viewer : Sets to the time of the computer connected.
4. When done, click [Apply (
)].
the <Synchronize with PC viewer>, the standard timezone should be set the same
JJ `` Ifasyoutheselect
current timezone in PC.
English _87
● setup screen
2. Click <Date & Time>.
setup screen
User
1. From the Setup menu, select the
<System (
)> tab.
2. Click <User>.
3. Provide the necessary user information.
•• Administrator password change :
Change the password for the
administrator.
`` The default password can be exposed to
a hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related
issues caused by the unchanged password
shall be responsible for the user.
•• Guest setup : If you select <Enable guest access>, the guest account can access
the Web viewer screen but can only view the live Viewer screen.
`` The ID/password for the guest account is <guest/guest>, which cannot be changed.
•• Authentication setup : If you select <Enable RTSP connection without
authentication>, you can access RTSP without logging in and view the video.
•• Current users : If you select <Use>, you can set or change the user permissions.
`` The administrator can set the audio input, audio output and alarm output permissions.
`` Profile : If you select <Default>, you can only see the default profile video; if selecting <All>, you
can see the full profile videos.
functions available to a registered user allowed to use ONVIF functions are limited to those
JJ `` ONVIF
of granted with permission.
`` Video Transfer and Changing Video Information: Set the profile to <All>, and set Audio Input and
Audio Output.
`` Video Transfer, Changing Video Information, Alarm Output : Set the profile to <All>, and select at
your preference for the rest.
4. When done, click [Apply (
88_ setup screen
)].
Upgrade / Reboot
1. From the Setup menu, select the
<System (
)> tab.
3. Select a desired item and set it
appropriately.
•• Upgrade : Performs upgrading the
system.
•• Factory default : Resets the system
to the factory default.
-- Except network parameter : Reset the other settings except for Network settings.
-- All : Resets all settings including the camera settings. (however, the log
information will not be reset)
`` The IP addressing system will be defaulted to DHCP if you reset the camera. If no DHCP server is
found, the previous settings will be restored automatically.
•• Configuration backup & Restore : Backs up the current system settings before
performing the restoration process. The system is automatically restarts after
backup or restoration.
•• Restart : Restarts the system.
To perform the upgrade
1. Click [Upgrade].
2. Click [Browse] and specify a file to
upgrade.
3. Click [Send].
4. The “Upgrade” dialog appears where
the progression will be shown in the
bottom.
5. Once completed upgrading, the
browser exits and the camera restarts.
English _89
● setup screen
2. Click <Upgrade / Reboot>.
setup screen
take a max of 20 minutes for the upgrade process.
MM `` ItIf may
you forcibly terminate the upgrade process, upgrade will not be completed properly.
`` During restarting the system, accessing with web viewer will not be made.
`` You can download the latest version from the Samsung web site (www.samsungcctv.com).
To back up the current settings
1. Click [Backup].
The Save As dialog should appear.
2. Specify the backup path with a proper
file name, and click [Save].
The backup file will be saved to the
specified path in the format of “.bin”.
To restore the backup settings
1. To restore the backup settings, click
[Restore].
2. Select a backup file and click [Open].
the backup or restoration,
MM `` Iftheyouwebperform
browser will be closed and the
camera will reboots.
90_ setup screen
Log
You can check the system log or event log.
1. From the Setup menu, select the
<System (
)> tab.
● setup screen
2. Click <Log>.
3. Select a log type.
•• System : You can check the system
logs where any system changes
are recorded including the time
information.
•• Event : You can check the event logs
including the time information.
4. From the right log list, select an item to
search for.
•• If you select <All> in the top left dropdown list, all logs for the applicable log type
will be displayed.
5. If one page can not display all the logs available, use the bottom buttons to move to
the previous, next, or the last item.
If you want to view the details of a log, click [Info (
MM `` information
will be shown in the bottom pane.
)] in the right column of the log; the log
`` Each page displays 15 logs with the latest one displayed at the top.
`` The event/system log list can contain up to 1000 logs; after that, the existing logs will be deleted
from the oldest one each time a new log is created.
English _91
setup screen
Profile access
You can check the profile information.
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Profile access>.
•• Profile access : Show the information
of the newly added profile.
-- Profile : Show the information of the
newly added codec.
-- Bitrate(kbps) : Show both the actual
bit rate and the set bit rate.
-- Framerate(fps) : Show both the actual frame rate and the set frame rate.
-- ATC(%) : Show the ATC status.
-- Concurrent users count : Show the number of concurrent users who access the
profile.
•• Current users : Shows information on users accessing web viewer and displaying
monitoring video.
-- Profile : Show the name of the profile accessed by the user.
-- IP address : Show the IP address of the current user.
-- Bitrate(kbps) : Show the current bit rate.
-- Network connection status : You can check the network connection status.
MM `` To check information on the profile currently used, click <Profile access> again to refresh it.
92_ setup screen
appendix
Specification
Items
Imaging Device
1/3" 1.3M PS CMOS
Effective Pixels
1,329(H) x 1,049(V)
Video
Scanning System
Min. Illumination
S / N Ratio
Video Out
Focal Length (Zoom Ratio)
Max. Aperture Ratio
Lens
Angular Field of View
Focus Control
Lens Type
Mount Type
Pan Range
Pan Speed
Pan / Tilt /
Rotate
Tilt Range
Tilt Speed
Rotate Range
Preset
Preset Accuracy
Auto Tracking
1,384(H) x 1,076(V)
● appendix
Total Pixels
Description
Progressive
Color : 0.3 Lux (F1.2, 50IRE)
B/W : 0 Lux (F1.2, 50IRE, IR LED ON)
50dB
CVBS : 1.0 Vp-p / 75Ω composite, 704x480(N),
704x576(P), for installation
3~8.5mm (2.8X) Motorized Vari-focal
F1.2
H : 91.0°(Wide)~32.1°(Tele), V : 72.2°(Wide)~25.7°(Tele)
Remote control via network (Manual, One-shot AF)
DC Auto Iris
Board-in type
0°~355°
-
0°~90°
-
0°~355°
-
English _93
appendix
Items
15ea
Camera Title
Off / On (Displayed up to 15 characters)
Viewable Length
Day & Night
Backlight Compensation
Wide Dynamic Range
Contrast Enhancement
Digital Noise Reduction
Digital Image Stabilization
Motion Detection
Privacy Masking
Operational
Description
IR LED
Sens-up
(Frame Integration)
15m
Auto (ICR) / Color / B/W / External B/W
Off / BLC / HLC
-
SSDR (Samsung Super Dynamic Range) (Off / On)
SSNRIII (2D+3D Noise Filter) (Off / On)
-
Off / On (4 programmable zones)
Off / On (1ea 4 Point Polygonal + 12ea Rectangular zones)
Off / Auto (2X ~ 60X)
Gain Control
AGC (Off / Low / Medium / High)
Electronic Shutter Speed
ESC / A.FLK / Manual (1/30 ~ 30,000sec)
White Balance
Digital Zoom
Flip / Mirror
Intelligent Video Analytics
Alarm I/O
Remote Control Interface
RS-485 Protocol
Alarm Triggers
ATW / AWC / Manual / Indoor / Outdoor
-
Off / On
Tampering, Virtual Line, Enter / Exit, Appear(Disappear)
Digital Input 1ea / Digital Output 1ea
-
Motion detection, Video Analytics, Alarm Input, Network
Disconnect
yy File upload via FTP, E-Mail
Alarm events
94_ appendix
yy Notification via E-Mail, TCP
yy local storage(SD/SDHC) recording at Network
disconnected
Items
RJ-45 (10/100BASE-T)
Resolution
1280x1024, 1280x720P(HD), 1024x768, 800x600,
640x480, 320x240
Video Compression Format
Video Quality Adjustment
Bitrate Control Method
Streaming Capability
Audio I/O
Audio Compression Format
Audio Communication
IP
Protocol
H.264, MPEG-4, MJPEG
H.264, MJPEG : 30fps
MPEG-4 : 25fps(1280x1024), 30fps (720P HD)
H.264 / MPEG-4 : Compression Level, Target Bitrate Level Control
MJPEG : Quality Level Control
H.264 / MPEG-4 : CBR or VBR
MJPEG : VBR
Multiple Streaming (Up to 10 Profiles)
Mic / Line in, Line out
G.711 μ-law
Bi-directional audio
IPv4, IPv6
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP,
HTTP, HTTPS, SSL, DHCP, PPPoE, FTP, SMTP, ICMP,
IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, QoS
HTTPS(SSL) Login Authentication
Security
Streaming Method
Digest Login Authentication
IP Address Filtering
User access Log
802.1x authentication
Unicast / Multicast
English _95
● appendix
Max. Framerate
Network
Description
Ethernet
appendix
Items
10 users at Unicast Mode
ONVIF Conformance
Yes
Memory Slot
Network
Webpage Language
Web Viewer
Central Management Software
Environmental
Operating Temperature /
Humidity
Ingress Protection
Electrical
Mechanical
96_ appendix
Description
Max. User Access
Input Voltage / Current
Power Consumption
Color / Material
Dimension (ØxH)
Weight
SD/SDHC Memory Slot
English, French, German, Spanish, Italian, Chinese, Korean,
Russian, Japanese, Swedish, Denish, Portuguese, Czech,
Polish, Turkish, Rumanian, Serbian, Dutch, Croatian,
Hungarian, Greek, Finnish, Norwegian
Supported OS : Windows XP / VISTA / 7, MAC OS
Supported Browser : Internet Explorer 7.0 or Higher,
Firefox, Chrome, Safari
NET-i viewer
AC24V : -40°C ~ +55°C (-40°F ~ +131°F) / ~ 90% RH
(Heater On)
DC12V, PoE : -10°C ~ +55°C (+14°F ~ +131°F) /
~ 90% RH (Heater Off)
IP66 Grade (Waterproof)
12V DC, 24V AC, PoE(IEEE802.3af)
Max. 9W or 650mA (Heater Off),
Max. 13W or 800mA (Heater On)
* Heater works at AC Input only
Body : Ivory / Aluminum
Ø160.0 x H134.5 mm
1.4Kg
Product Overview
46.0 (1.81")
85.0 (3.35")
● appendix
34.5 (1.36")
Unit : mm (inch)
83.5 (3.29")
85.0 (3.35")
134.5 (5.30")
160.0 (6.30")
100.0 (3.94")
English _97
appendix
Flushed mode
")
3
.6
.0
(5
3
4
1
76.5 (3.01")
48.5 (1.91")
122.5 (4.82")
2.0 (0.08")
30
30
160.0 (6.30")
100.0 (3.94")
98_ appendix
Troubleshooting
PROBLEM
SOLUTION
I can’t access the camera from a
web browser.
yy Check to make sure that all network cables have been connected
properly.
yy If connected using DHCP, verify that the camera is able to acquire
dynamic IP addresses without any problem.
yy If the camera is connected to a router, verify that port forwarding is
properly configured.
Viewer got disconnected during
monitoring.
yy Connected Viewers become disconnected upon any change to camera or
network configurations.
yy Check all network connections.
yy If the camera is connected over an PPPoE network, it’ s possible for
Viewer to disconnect under poor network conditions.
I cannot connect to the system
using a tab browser of Internet
Explorer 7.0.
yy When you try to connect to the system using a tab browser, the same
cookie information is shared, resulting in errors when connected.
Therefore, instead of using a tab browser, open a new browser window
to connect to the system.
The camera connected to the
network is not detected in the IP
installer program.
yy Turn off the firewall settings on your PC and then search the camera
again.
Images overlap.
yy Check whether two or more cameras are set to a single multicast address
instead of different addresses. If a single address is used for multiple
cameras, the images may overlap.
No image appears.
yy If the transmission method is set to multicast, check whether there is a
router that supports multicast in the LAN the camera is connected to.
English _99
● appendix
yy Check to make sure that the camera’s Network settings are appropriate.
appendix
PROBLEM
<Motion detection / Video
analytics> of <Event setup> is set
to <Enable>, but no notification
e-mail reaches me even when an
analysis event had occurred.
SOLUTION
yy Verify the settings in the following sequence:
A. Check <Data & Time> settings.
B. The <Motion detection / Video analytics> should be set to <Enable>.
C. Check if the <E-mail> option of <Event action setup> menu is
checked to use.
Can I define event rules even
when I don’t use <Motion
detection / Video analytics>?
yy Yes, it can be. You can set rules for events despite of the intelligent
video analysis setting.
No signal is found at the Alarm
Output port even when an
intelligent video analysis event is
generated.
yy Check alarm output port settings.
Cannot record into the SD memory yy Check if the memory card is defective.
card.
yy Check if the write protection tab of the memory card is set to “LOCK”.
SD memory card is inserted but
the camera does not operate
properly.
Cannot format the SD memory
card.
100_ appendix
yy Check if the memory card is inserted in the proper direction. Operation
of memory card that is formatted by other devices is not guaranteed with
this camera unit
yy Format the memory card again in <Setup>  <Event>  <Storage>
menu.
yy Check if the write protection tab of the memory card is set to “LOCK”.
Open Source Announcement
GPL/LGPL software license
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain
the complete Corresponding Source code from us for a period of three years after our last shipment of this product by
sending email to help.cctv@samsung.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of
physically performing source distribution might be charged.
•• GPL S/W
-- Base Kernel, Busybox, Sysvinit, dosfstools, DSP-SW-package
•• LGPL S/W
-- gLibc, Inetutils
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C)1989, 1991 Free Software Foundation, Inc. 51
Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public License is intended to guarantee your
freedom to share and change free software-- to make sure
the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s
software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is
covered by the GNU Lesser General Public License instead.)
You can apply it to your programs, too. When we speak of
free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source
code or can get it if you want it, that you can change the
software or use pieces of it in new free programs ; and that
you know you can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the software,
or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have.
You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they
know their rights. We protect your rights with two steps :
(1)copyright the software, and (2)offer you this license which
gives you legal permission to copy, distribute and/or modify
the software. Also, for each author’s protection and ours, we
want to make certain that everyone understands that there is
no warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any
problems introduced by others will not reflect on the original
authors’ reputations.
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a
free program will individually obtain patent licenses, in effect
making the program proprietary. To prevent this, we have
made it clear that any patent must be licensed for everyone’s
free use or not licensed at all. The precise terms and
conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
Version 2, June 1991 Copyright (C) 1989, 1991 Free
Software Foundation, Inc. 51 Franklin S
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying
it may be distributed under the terms of this General
Public License.
The “Program”, below, refers to any such program or
work, and a “work based on the Program” means either
the Program or any derivative work under copyright law :
that is to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/or translated
into another language. (Hereinafter, translation is included
without limitation in the term “modification”.) Each licensee is
addressed as “you”.
Activities other than copying, distribution and modification are
not covered by this License ; they are outside its scope. The
act of running the Program is not restricted, and the output
from the Program is covered only if its contents constitute
a work based on the Program (independent of having been
made by running the Program). Whether that is true depends
on what the Program does.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer
to this License and to the absence of any warranty ; and
give any other recipients of the Program a copy of this
License along with the Program.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection
in exchange for a fee.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or
work under the terms of Section 1 above, provided that
you also meet all of these conditions :
a) Y
ou must cause the modified files to carry prominent
notices stating that you changed the files and the date
of any change.
b) You must cause any work that you distribute or publish,
that in whole or in part contains or is derived from
the Program or any part thereof, to be licensed as a
whole at no charge to all third parties under the terms
of this License.
c) If the modified program normally reads commands
interactively when run,you must cause it, when started
running for such interactive use in the most ordinary
way, to print or display an announcement including
an appropriate copyright notice and a notice that
there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program
under these conditions, and telling the user how to
view a copy of this License. (Exception:if the Program
itself is interactive but does not normally print such an
announcement, your work based on the Program is not
required to print an announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent
and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute
them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms
of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part
regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you ; rather,
the intent is to exercise the right to control the distribution
of derivative or collective works based on the Program. In
addition, mere aggregation of another work not based on
the Program with the Program (or with a work based on the
Program)on a volume of a storage or distribution medium
does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work
based on it, under Section 2)in object code or executable
form under the terms of Sections 1 and 2 above provided
that you also do one of the following :
a) Accompany it with the complete corresponding
machine-readable source code, which must be distributed
under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange ; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a
complete machinereadable copy of the corresponding
source code, to be distributed under the terms of Sections
1 and 2 above on a medium customarily used for software
interchange ; or,
c) Accompany it with the information you received as to
the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution
and only if you received the program in object code
or executable form with such an offer, in accord with
Subsection b above.) The source code for a work means
the preferred form of the work for making modifications
to it. For an executable work, complete source code
means all the source code for all modules it contains,
plus any associated interface definition files, plus the
scripts used to control compilation and installation of
the executable. However, as a special exception, the
source code distributed need not include anything that
is normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so on)
of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from
the same place counts as distribution of the source code,
even though third parties are not compelled to copy the
source along with the object code.
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this License.
Any attempt otherwise to copy, modify, sublicense or
distribute the Program is void, and will automatically
terminate your rights under this License.
However, parties who have received copies, or rights, from
you under this License will not have their licenses terminated
so long as such parties remain in full compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works.
These actions are prohibited by law if you do not accept this
License.Therefore, by modifying or distributing the Program
(or any work based on the Program), you indicate your
acceptance of this License to do so, and all its terms and
conditions for copying, distributing or modifying the Program
or works based on it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights granted
herein. You are not responsible for enforcing compliance
by third parties to this License.
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether
by court order, agreement or otherwise)that contradict the
conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so
as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a
consequence you may not distribute the Program at all.
For example, if a patent license would not permit royaltyfree
redistribution of the Program by all those who receive copies
directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely
from distribution of the Program.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended
to apply in other circumstances. It is not the purpose of
this section to induce you to infringe any patents or other
property right claims or to contest validity of any such
claims; this section has the sole purpose of protecting the
integrity of the free software distribution system, which is
implemented by public license practices. Many people have
made generous contributions to the wide range of software
distributed through that system in reliance on consistent
application of that system ; it is up to the author/donor to
decide if he or she is willing to distribute software through
any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Program under this License may add an explicit
geographical distribution limitation excluding those
countries,so that distribution is permitted only in or among
countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of
this License.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time
to time. Such new versions will be similar in spirit to
the present version, but may differ in detail to address
new problems or concerns. Each version is given a
distinguishing version number. If the Program specifies
a version number of this License which applies to it and
“any later version”, you have the option of following the
terms and conditions either of that version or of any later
version published by the Free Software Foundation. If
the Program does not specify a version number of this
License, you may choose any version ever published by
the Free Software Foundation.
10. If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation,write to the Free Software Foundation ; we
sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the
sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE PROGRAM “ASIS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE
QUALITY AND PERFORMANCE OF THE PROGRAM IS
WITH YOU. SHOULD THE PROGRAMPROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT
UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs If you
develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to
make it free software which everyone can redistribute and
change under these terms.
To do so, attach the following notices to the program. It is safest
to attach them to the start of each source file to most effectively
convey the exclusion of warranty ; and each file should have at
least the “copyright” line and a pointer to where the full notice
is found.one line to give the program’s name and an idea of
what it does.
Copyright (C)yyyy name of author
This program is free software ; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation ; either version
2 of the License, or (at your option)any later version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY ; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR
A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public
License along with this program ; if not, write to the Free
Software Foundation, Inc.,51 Franklin Street, Fifth Floor,
Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic
and paper mail. If the program is interactive, make it output a
short notice like this when it starts in an interactive mode :
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY ;
for details type ‘show w’. This is free software, and you are
welcome to redistribute it under certain conditions ; type ‘show
c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should
show the appropriate parts of the General Public License.
Of course, the commands you use may be called something
other than ‘show w’ and ‘show c’ ; they could even be
mouse-clicks or menu items-- whatever suits your program.
You should also get your employer (if you work as a
programmer)or your school, if any, to sign a “copyright
disclaimer” for the program,if necessary. Here is a sample ;
alter the names:
Yoyodyne, Inc.,hereby disclaims all copyright interest in the
program ‘Gnomovision’ (which makes passes at compilers)
written by James Hacker. signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice This General Public License does
not permit incorporating
your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit
linking proprietary applications with the library. If this is
Lwihcaetn ysoeu want to do, use the GNU Lesser General
Public instead of this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.
org/>
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license
for software and other kinds of works. The licenses for
most software and other practical works are designed to
take away your freedom to share and change the works.
By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change all versions of
a program--to make sure it remains free software for all its
users.
We, the Free Software Foundation, use the GNU General
Public License for most of our software; it applies also to any
other work released this way by its authors.
You can apply it to your programs, too. When we speak of
free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and
charge for them if you wish), that you receive source code or
can get it if you want it, that you can change the software or
use pieces of it in new free programs, and that you know you
can do these things.
To protect your rights, we need to prevent others from
denying you these rights or asking you to surrender
the rights. Therefore, you have certain responsibilities if
you distribute copies of the software, or if you modify it:
responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must pass on to the
recipients the same freedoms that you received. You must
make sure that they, too, receive or can get the source code.
And you must show them these terms so they know their
rights. Developers that use the GNU GPL protect your rights
with two steps: (1) assert copyright on the software, and (2)
offer you this License giving you legal permission to copy,
distribute and/or modify it. For the developers’ and authors’
protection, the GPL clearly explains that there is no warranty
for this free software. For both users’ and authors’ sake, the
GPL requires that modified versions be marked as changed,
so that their problems will not be attributed erroneously to
authors of previous versions. Some devices are designed to
deny users access to install or run modified versions of the
software inside them, although the manufacturer can do so.
This is fundamentally incompatible with the aim of protecting
users’ freedom to change the software. The systematic
pattern of such abuse occurs in the area of products
for individuals to use, which is precisely where it is most
unacceptable. Therefore, we have designed this version of
the GPL to prohibit the practice for those products. If such
problems arise substantially in other domains, we stand
ready to extend this provision to those domains in future
versions of the GPL, as needed to protect the freedom of
users.
Finally, every program is threatened constantly by software
patents. States should not allow patents to restrict
development and use of software on general-purpose
omputers, but in those that do, we wish to avoid the special
anger that patents applied to a free program could make it
ffectively proprietary. To prevent this, the GPL assures that
atents cannot be used to render the program non-free. he
precise terms and conditions for copying, distribution and
modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public
License.
“Copyright” also means copyright-like laws that apply to
other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed
under this License. Each licensee is addressed as “you”.
“Licensees” and “recipients” may be individuals or
organizations.
To “modify” a work means to copy from or adapt all or part
of the work in a fashion requiring copyright permission, other
than the making of an exact copy. The resulting work is
called a “modified version” of the earlier work or a work “based
on” the earlier work.
A “covered work” means either the unmodified Program or a
work based on the Program.
To “propagate” a work means to do anything with it that,
without permission, would make you directly or secondarily
liable for infringement under applicable copyright law, except
executing it on a computer or modifying a private copy.
Propagation includes copying, distribution (with or without
modification), making available to the public, and in some
countries other activities as well.
To “convey” a work means any kind of propagation that
enables other parties to make or receive copies. Mere
interaction with a user through a computer network, with
no transfer of a copy, is not conveying. An interactive user
interface displays “Appropriate Legal Notices” to the extent
that it includes a convenient and prominently visible feature
that (1) displays an appropriate copyright notice, and (2)
tells the user that there is no warranty for the work (except
to the extent that warranties are provided), that licensees
may convey the work under this License, and how to view
a copy of this License. If the interface presents a list of user
commands or options, such as a menu, a prominent item in
the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of
the work for making modifications to it. “Object code” means
any non-source form of a work.
A “Standard Interface” means an interface that either is
an official standard defined by a recognized standards
body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among
developers working in that language.
The “System Libraries” of an executable work include
anything, other than the work as a whole, that (a) is included
in the normal form of packaging a Major Component,
but which is not part of that Major Component, and (b)
serves only to enable use of the work with that Major
Component, or to implement a Standard Interface for which
an implementation is available to the public in source code
form. A “Major Component”, in this context, means a major
essential component (kernel, window system, and so on) of
the specific operating system (if any) on which the executable
work runs, or a compiler used to produce the work, or an
object code interpreter used to run it.
The “Corresponding Source” for a work in object code
form means all the source code needed to generate, install,
and (for an executable work) run the object code and to
modify the work, including scripts to control those activities.
However, it does not include the work’s System Libraries,
or generalpurpose tools or generally available free programs
which are used unmodified in performing those activities but
which are not part of the work. For example, Corresponding
Source includes interface definition files associated with
source files for the work, and the source code for shared
libraries and dynamically linked subprograms that the work
is specifically designed to require, such as by intimate data
communication or control flow between those subprograms
and other parts of the work.
The Corresponding Source need not include anything that
users can regenerate automatically from other parts of the
Corresponding Source. The Corresponding Source for a
work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term
of copyright on the Program, and are irrevocable provided
the stated conditions are met. This License explicitly affirms
your unlimited permission to run the unmodified Program.
The output from running a covered work is covered by this
License only if the output, given its content, constitutes a
covered work. This License acknowledges your rights of fair
use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you
do not convey, without conditions so long as your license
otherwise remains in force. You may convey covered works to
others for the sole purpose of having them make modifications
exclusively for you, or provide you with facilities for running
those works, provided that you comply with the terms of this
License in conveying all material for which you do not control
copyright. Those thus making or running the covered works for
you must do so exclusively on your behalf, under your direction
and control, on terms that prohibit them from making any
copies of your copyrighted material outside their relationship
with you. Conveying under any other circumstances
is permitted solely under the conditions stated below.
Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From anti-Circumvention
Law.
No covered work shall be deemed part of an effective
technological measure under any applicable law fulfilling
obligations under article 11 of the WIPO copyright treaty
adopted on 20 December 1996, or similar laws prohibiting or
restricting circumvention of such measures.
When you convey a covered work, you waive any legal
power to forbid circumvention of technological measures to
the extent such circumvention is effected by exercising rights
under this License with respect to the covered work, and
you disclaim any intention to limit operation or modification of
the work as a means of enforcing, against the work’s users,
your or third parties’ legal rights to forbid circumvention of
technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source
code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an
appropriate copyright notice; keep intact all notices stating
that this License and any non-permissive terms added in
accord with section 7 apply to the code; keep intact all
notices of the absence of any warranty; and give all recipients
a copy of this License along with the Program. You may
charge any price or no price for each copy that you convey,
and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the
modifications to produce it from the Program, in the form of
source code under the terms of section 4, provided that you
also meet all of these conditions:
a) T
he work must carry prominent notices stating that you
modified it, and giving a relevant date.
b) T
he work must carry prominent notices stating that
it is released under this License and any conditions
added under section 7. This requirement modifies the
requirement in section 4 to “keep intact all notices”.
c) Y
ou must license the entire work, as a whole, under
this License to anyone who comes into possession of
a copy. This License will therefore apply, along with any
applicable section 7 additional terms, to the whole of
the work, and all its parts, regardless of how they are
packaged. This License gives no permission to license
the work in any other way, but it does not invalidate
such permission if you have separately received it.
d) If the work has interactive user interfaces, each must
display Appropriate Legal Notices; however, if the
Program has interactive interfaces that do not display
Appropriate Legal Notices, your work need not make
them do so. A compilation of a covered work with
other separate and independent works, which are not
by their nature extensions of the covered work, and
which are not combined with it such as to form a larger
program, in or on a volume of a storage or distribution
medium, is called an “aggregate” if the compilation and
its resulting copyright are not used to limit the access or
legal rights of the compilation’s users beyond what the
individual works permit. Inclusion of a covered work in
an aggregate does not cause this License to apply to
the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under
the terms of sections 4 and 5, provided that you also convey
the machine-readable Corresponding Source under the
terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical
product (including a physical distribution medium),
accompanied by the Corresponding Source fixed on a
durable physical medium customarily used for software
interchange.
b) Convey the object code in, or embodied in, a physical
product (including a physical distribution medium),
accompanied by a written offer, valid for at least three
years and valid for as long as you offer spare parts or
customer support for that product model, to give anyone
who possesses the object code either (1) a copy of the
Corresponding Source for all the software in the product
that is covered by this License, on a durable physical
medium customarily used for software interchange, for
a price no more than your reasonable cost of physically
performing this conveying of source, or (2) access to
copy the Corresponding Source from a network server
at no charge.
c) Convey individual copies of the object code with a
copy of the written offer to provide the corresponding
Source. This alternative is allowed only occasionally and
noncommercially, and only if you received the object
code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a
designated place (gratis or for a charge), and offer
equivalent access to the Corresponding Source in
the same way through the same place at no further
charge. You need not require recipients to copy the
Corresponding Source along with the object code. If
the place to copy the object code is a network server,
the Corresponding Source may be on a different
server (operated by you or a third party) that supports
equivalent copying facilities, provided you maintain clear
directions next to the object code saying where to find
the Corresponding Source. Regardless of what server
hosts the Corresponding Source, you remain obligated
to ensure that it is available for as long as needed to
satisfy these requirements.
e) Convey the object code using peer-to-peer
transmission, provided you inform other peers where the
object code and Corresponding Source of the work are
being offered to the general public at no charge under
subsection 6d. A separable portion of the object code,
whose source code is excluded from the Corresponding
Source as a System Library, need not be included in
conveying the object code work. A “User Product”
is either (1) a “consumer product”, which means any
tangible personal property which is normally used for
personal, family, or household purposes, or (2) anything
designed or sold for incorporation into a dwelling. In
determining whether a product is a consumer product,
doubtful cases shall be resolved in favor of coverage.
For a particular product received by a particular user,
“normally used” refers to a typical or common use of that
class of product, regardless of the status of the particular
user or of the way in which the particular user actually
uses, or expects or is expected to use, the product. A
product is a consumer product regardless of whether
the product has substantial commercial, industrial or
non-consumer uses, unless such uses represent the
only significant mode of use of the product.
“Installation Information” for a User Product means
any methods, procedures, authorization keys, or other
information required to install and execute modified versions
of a covered work in that User Product from a modified
version of its Corresponding Source. The information must
suffice to ensure that the continued functioning of the
modified object code is in no case prevented or interfered
with solely because modification has been made. If you
convey an object code work under this section in, or with,
or specifically for use in, a User Product, and the conveying
occurs as part of a transaction in which the right of
possession and use of the User Product is transferred to the
recipient in perpetuity or for a fixed term (regardless of how
the transaction is characterized), the Corresponding Source
conveyed under this section must be accompanied by the
Installation Information. But this requirement does not apply
if neither you nor any third party retains the ability to install
modified object code on the User Product (for example, the
work has been installed in ROM).
The requirement to provide Installation Information does not
include a requirement to continue to provide support service,
warranty, or updates for a work that has been modified or
installed by the recipient, or for the User Product in which
it has been modified or installed. Access to a network
may be denied when the modification itself materially and
adversely affects the operation of the network or violates the
rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information
provided, in accord with this section must be in a format that
is publicly documented (and with an implementation available
to the public in source code form), and must require no
special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the
terms of this License by making exceptions from one or more
of its conditions. Additional permissions that are applicable
to the entire Program shall be treated as though they were
included in this License, to the extent that they are valid
under applicable law. If additional permissions apply only to
part of the Program, that part may be used separately under
those permissions, but the entire Program remains governed
by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your
option remove any additional permissions from that copy, or
from any part of it. (Additional permissions may be written to
require their own removal in certain cases when you modify
the work.) You may place additional permissions on material,
added by you to a covered work, for which you have or
can give appropriate copyright permission. Notwithstanding
any other provision of this License, for material you add to
a covered work, you may (if authorized by the copyright
holders of that material) supplement the terms of this License
with terms:
a) Disclaiming warranty or limiting liability differently from
the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal
notices or author attributions in that material or in
the Appropriate Legal Notices displayed by works
containing it; or
c) Prohibiting misrepresentation of the origin of that
material, or requiring that modified versions of such
material be marked in reasonable ways as different from
the original version; or
d) Limiting the use for publicity purposes of names of
licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of
some trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of
that material by anyone who conveys the material (or
modified versions of it) with contractual assumptions
of liability to the recipient, for any liability that these
contractual assumptions directly impose on those
licensors and authors. All other non-permissive
additional terms are considered “further restrictions”
within the meaning of section 10. If the Program as you
received it, or any part of it, contains a notice stating
that it is governed by this License along with a term
that is a further restriction, you may remove that term.
If a license document contains a further restriction but
permits relicensing or conveying under this License,
you may add to a covered work material governed by
the terms of that license document, provided that the
further restriction does not survive such relicensing or
conveying. If you add terms to a covered work in accord
with this section, you must place, in the relevant source
files, a statement of the additional terms that apply
to those files, or a notice indicating where to find the
applicable terms. Additional terms, permissive or nonpermissive, may be stated in the form of a separately
written license, or stated as exceptions; the above
requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as
expressly provided under this License. Any attempt otherwise
to propagate or modify it is void, and will automatically
terminate your rights under this License (including any patent
licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your
license from a particular copyright holder is reinstated (a)
provisionally, unless and until the copyright holder explicitly
and finally terminates your license, and (b) permanently, if
the copyright holder fails to notify you of the violation by
some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is
reinstated permanently if the copyright holder notifies you
ofthe violation by some reasonable means, this is the first time
you have received notice of violation of this License (for any
work) from that copyright holder, and you cure the violation
prior to 30 days after your receipt of the notice. Termination of
your rights under this section does not terminate the licenses
of parties who have received copies or rights from you under
this License. If your rights have been terminated and not
permanently reinstated, you do not qualify to receive new
licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive
or run a copy of the Program. Ancillary propagation of a
covered work occurring solely as a consequence of using
peer-to-peer transmission to receive a copy likewise does
not require acceptance. However, nothing other than this
License grants you permission to propagate or modify any
covered work. These actions infringe copyright if you do not
accept this License. Therefore, by modifying or propagating
a covered work, you indicate your acceptance of this License
to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient
automatically receives a license from the original licensors,
to run, modify and propagate that work, subject to this
License. You are not responsible for enforcing compliance
by third parties with this License. An “entity transaction”
is a transaction transferring control of an organization, or
substantially all assets of one, or subdividing an organization,
or merging organizations. If propagation of a covered
work results from an entity transaction, each party to that
transaction who receives a copy of the work also receives
whatever licenses to the work the party’s predecessor in
interest had or could give under the previous paragraph, plus
a right to possession of the Corresponding Source of the
work from the predecessor in interest, if the predecessor has
it or can get it with reasonable efforts. You may not impose
any further restrictions on the exercise of the rights granted
or affirmed under this License. For example, you may not
impose a license fee, royalty, or other charge for exercise of
rights granted under this License, and you may not initiate
litigation (including a cross-claim or counterclaim in a lawsuit)
alleging that any patent claim is infringed by making, using,
selling, offering for sale, or importing the Program or any
portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use
under this License of the Program or a work on which the
Program is based. The work thus licensed is called the
contributor’s “contributor version”. A contributor’s “essential
patent claims” are all patent claims owned or controlled
by the contributor, whether already acquired or hereafter
acquired, that would be infringed by some manner, permitted
by this License, of making, using, or selling its contributor
version, but do not include claims that would be infringed
only as a consequence of further modification of the
contributor version. For purposes of this definition, “control”
includes the right to grant patent sublicenses in a manner
consistent with the requirements of this License. Each
contributor grants you a non-exclusive, worldwide, royaltyfree patent license under the contributor’s essential patent
claims, to make, use, sell, offer for sale, import and otherwise
run, modify and propagate the contents of its contributor
version.
In the following three paragraphs, a “patent license” is any
express agreement or commitment, however denominated,
not to enforce a patent (such as an express permission
to practice a patent or covenant not to sue for patent
infringement). To “grant” such a patent license to a party
means to make such an agreement or commitment not
to enforce a patent against the party. If you convey a
covered work, knowingly relying on a patent license, and
the Corresponding Source of the work is not available for
anyone to copy, free of charge and under the terms of this
License, through a publicly available network server or other
readily accessible means, then you must either (1) cause the
Corresponding Source to be so available, or (2) arrange to
deprive yourself of the benefit of the patent license for this
particular work, or (3) arrange, in a manner consistent with
the requirements of this License, to extend the patent license
to downstream recipients. “Knowingly relying” means you
have actual knowledge that, but for the patent license, your
conveying the covered work in a country, or your recipient’s
use of the covered work in a country, would infringe one or
more identifiable patents in that country that you have reason
to believe are valid. If, pursuant to or in connection with a
single transaction or arrangement, you convey, or propagate
by procuring conveyance of, a covered work, and grant a
patent license to some of the parties receiving the covered
work authorizing them to use, propagate, modify or convey
a specific copy of the covered work, then the patent license
you grant is automatically extended to all recipients of the
covered work and works based on it. A patent license is
“discriminatory” if it does not include within the scope of its
coverage, prohibits the exercise of, or is conditioned on the
non-exercise of one or more of the rights that are specifically
granted under this License. You may not convey a covered
work if you are a party to an arrangement with a third party
that is in the business of distributing software, under which
you make payment to the third party based on the extent
of your activity of conveying the work, and under which the
third party grants, to any of the parties who would receive the
covered work from you, a discriminatory patent license
(a) in connection with copies of the covered work conveyedby
you (or copies made from those copies), or
(b) primarily for and in connection with specific products or
compilations that contain the covered work, unless you
entered into that arrangement, or that patent license
was granted, prior to 28 March 2007. Nothing in this
License shall be construed as excluding or limiting any
implied license or other defenses to infringement that may
otherwise be available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of
thisLicense. If you cannot convey a covered work so as to
satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you
may not convey it at all. For example, if you agree to terms
that obligate you to collect a royalty for further conveying
from those to whom you convey the Program, the only way
you could satisfy both those terms and this License would be
to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you
have permission to link or combine any covered work with
a work licensed under version 3 of the GNU Affero General
Public License into a single combined work, and to convey
the resulting work. The terms of this License will continue to
apply to the part which is the covered work, but the special
requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will
apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/ or
new versions of the GNU General Public License from time to
time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the
Program specifies that a certain numbered version of the
GNU General Public License “or any later version” applies to
it, you have the option of following the terms and conditions
either of that numbered version or of any later version
published by the Free Software Foundation. If the Program
does not specify a version number of the GNU General Public
License, you may choose any version ever published by the
Free Software Foundation. If the Program specifies that a
proxy can decide which future versions of the GNU General
Public License can be used, that proxy’s public statement
of acceptance of a version permanently authorizes you to
choose that version for the Program. Later license versions
may give you additional or different permissions. However, no
additional obligations are imposed on any author or copyright
holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/
OR CONVEYS THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided
above cannot be given local legal effect according to their
terms, reviewing courts shall apply local law that most
closely approximates an absolute waiver of all civil liability
in connection with the Program, unless a warranty or
assumption of liability accompanies a copy of the Program in
return for a fee.
END OF TERMS AND CONDITIONS GNU
LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed. [This is the first released version of the Lesser GPL.
It also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software to make sure the
software is free for all its users.
This license, the Lesser General Public License, applies
to some specially designated software packages-typically
libraries-of the Free Software Foundation and other authors
who decide to use it. You can use it too, but we suggest you
first think carefully about whether this license or the ordinary
General Public License is the better strategy to use in any
particular case, based on the explanations below. When we
speak of free software, we are referring to freedom of use, not
price. Our General Public Licenses are designed to make sure
that you have the freedom to distribute copies of free software
(and charge for this service if you wish); that you receive
source code or can get it if you want it; that you can change
the software and use pieces of it in new free programs; and
that you are informed that you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the library or
if you modify it.
For example, if you distribute copies of the library, whether
gratis or for a fee, you must give the recipients all the rights
that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code
with the library, you must provide complete object files to the
recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you
must show them these terms so they know their rights. We
protect your rights with a two-step method: (1) we copyright
the library, and (2) we offer you this license, which gives you
legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the library
is modified by someone else and passed on, the recipients
should know that what they have is not the original version,
so that the original author’s reputation will not be affected by
problems that might be introduced by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free
program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained
for a version of the library must be consistent with the full
freedom of use specified in this license. Most GNU software,
including some libraries, is covered by the ordinary GNU
General Public License. This license, the GNU Lesser General
Public License, applies to certain designated libraries, and is
quite different from the ordinary General Public License. We
use this license for certain libraries in order to permit linking
those libraries into non-free programs.
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library.
The ordinary General Public License therefore permits such
linking only if the entire combination fits its criteria of freedom.
The Lesser General Public License permits more lax criteria
for linking other code with the library. We call this license the
“Lesser” General Public License because it does Less to
protect the user’s freedom than the ordinary General Public
License. It also provides other free software developers Less
of an advantage over competing non-free programs. These
disadvantages are the reason we use the ordinary General
Public License for many libraries.
However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special need
to encourage the widest possible use of a certain library, so
that it becomes a de-facto standard. To achieve this, nonfree
programs must be allowed to use the library. A more frequent
case is that a free library does the same job as widely used
non-free libraries. In this case, there is little to
gain by limiting the free library to free software only, so we
use the Lesser General Public License.
In other cases, permission to use a particular library in
nonfree programs enables a greater number of people to use
a large body of free software. For example, permission to use
the GNU C Library in non-free programs enables many more
people to use the whole GNU operating system, as well as
its variant, the GNU/ Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the user
of a program that is linked with the Library has the freedom
and
the wherewithal to run that program using a modified version
of the Library. The precise terms and conditions for copying,
distribution and modification follow. Pay close attention to the
difference between a “work based on the library” and a “work
that uses the library”. The former contains code derived from
the library, whereas the latter must be combined with the
library in order to run.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by the
copyright holder or other authorized party saying it may
be distributed under the terms of this Lesser General
Public License (also called “this License”). Each licensee is
addressed as “you”.
A “library” means a collection of software functions and/
or data prepared so as to be conveniently linked with
application programs (which use some of those functions
and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms. A
“work based on the Library” means either the Library or
any derivative work under copyright law: that is to say, a
work containing the Library or a portion of it, either verbatim
or with modifications and/or translated straightforwardly
into another language. (Hereinafter, translation is included
without limitation in the term “modification”.) “Source code”
for a work means the preferred form of the work for making
modifications to it. For a library, complete source code
means all the source code for all modules it contains, plus
any associated interface definition files, plus the scripts used
to control compilation and installation of the library.
Activities other than copying, distribution and modification are
not covered by this License; they are outside its scope. The
act of running a program using the Library is not restricted,
and output from such a program is covered only if its
contents constitute a work based on the Library (independent
of the use of the Library in a tool for writing it). Whether that
is true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all
the notices that refer to this License and to the absence of
any warranty; and distribute a copy of this License along
with the Library. You may charge a fee for the physical act
of transferring a copy, and you may at your option offer
warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library,
and copy and distribute such modifications or work under
the terms of Section 1 above, provided that you also meet
all of these conditions:
a) The modified work must itself be a software library.
b) Y
ou must cause the files modified to carry prominent
notices stating that you changed the files and the date
of any change. c) You must cause the whole of the work
to be licensed at no charge to all third parties under the
terms of this License. d) If a facility in the modified Library
refers to a function or a table of data to be supplied by
an application program that uses the facility, other than
as an argument passed when the facility is invoked, then
you must make a good faith effort to ensure that, in the
event an application does not supply such function or
table, the facility still operates, and performs whatever
part of its purpose remains meaningful. (For example,
a function in a library to compute square roots has a
purpose that is entirely well-defined independent of
the application. Therefore, Subsection 2d requires
that any application-supplied function or table used
by this function must be optional: if the application
does not supply it, the square root function must still
compute square roots.) These requirements apply to
the modified work as a whole. If identifiable sections
of that work are not derived from the Library, and can
be reasonably considered independent and separate
works in themselves, then this License, and its terms,
do not apply to those sections when you distribute them
as separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Library, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of
derivative or collective works based on the Library.
In addition, mere aggregation of another work not based
on the Library with the Library (or with a work based on the
Library) on a volume of a storage or distribution medium does
not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given
copy of the Library. To do this, you must alter all the notices
that refer to this License, so that they refer to the ordinary
GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary
GNU General Public License has appeared, then you can
specify that version instead if you wish.) Do not make any
other change in these notices. Once this change is made in a
given copy, it is irreversible for that copy, so the ordinary GNU
General Public License applies to all subsequent copies and
derivative works made from that copy. This option is useful
when you wish to copy part of the code of the Library into a
program that is not a library.
4. Y
ou may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided t hat you accompany it with the complete
corresponding machine-readable source code, which
must be distributed under the terms of Sections 1 and
2 above on a medium customarily used for software
interchange.
If distribution of object code is made by offering access
to copy from a designated place, then offering equivalent
access to copy the source code from the same place
satisfies the requirement to distribute the source code, even
though third parties are not compelled to copy the source
along with the object code.
5. A program that contains no derivative of any portion of
the Library, but is designed to work with the Library by
being compiled or linked with it, is called a “work that uses
the Library”. Such a work, in isolation, is not a derivative
work of the Library, and therefore falls outside the scope
of this License.
However, linking a “work that uses the Library” with the
Library creates an executable that is a derivative of the
Library (because it contains portions of the Library), rather
than a “work that uses the library”. The executable is
therefore covered by this License. Section 6 states terms for
distribution of such executables.
When a “work that uses the Library” uses material from a
header file that is part of the Library, the object code for the
work may be a derivative work of the Library even though
the source code is not. Whether this is true is especially
significant if the work can be linked without the Library, or if
the work is itself a library. The threshold for this to be true is
not precisely defined by law.
If such an object file uses only numerical parameters, data
structure layouts and accessors, and small macros and
small inline functions (ten lines or less in length), then the use
of the object file is unrestricted, regardless of whether it is
legally a derivative work. (Executables containing this object
code plus portions of the Library will still fall under Section
6.) Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the terms
of Section 6. Any executables containing that work also fall
under Section 6, whether or not they are linked directly with
the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification
of the work for the customer’s own use and reverse
engineering for debugging such modifications. You must
give prominent notice with each copy of the work that the
Library is used in it and that the Library and its use are
covered by this License. You must supply a copy of this
License. If the work during execution displays copyright
notices, you must include the copyright notice for the
Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one
of these things:
a) Accompany the work with the complete corresponding
machine-readable source code for the Library including
whatever changes were used in the work (which must
be distributed under Sections 1 and 2 above); and,
if the work is an executable linked with the Library,
with the complete machine readable “work that uses
the Library”, as object code and/or source code, so
that the user can modify the Library and then relink to
produce a modified executable containing the modified
Library. (It is understood that the user who changes
the contents of definitions files in the Library will not
necessarily be able to recompile the application to use
the modified definitions.)
b) Use a suitable shared library mechanism for linking
withthe Library. A suitable mechanism is one that (1)
uses at run time a copy of the library already present
on the user’s computer system, rather than copying
library functions into the executable, and (2) will operate
properly with a modified version of the library, if the
user installs one, as long as the modified version is
interface-compatible with the version that the work
was made with.
c) Accompany the work with a written offer, valid for at
least three years, to give the same user the materials
specified in Subsection 6a, above, for a charge no
more than the cost of performing this distribution.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from the
same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this user a
copy. For an executable, the required form of the “work
that uses the Library” must include any data and utility
programs needed for reproducing the executable from
it. However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that do
not normally accompany the operating system. Such a
contradiction means you cannot use both them and the
Library together in an executable that you distribute.
7. You may place library facilities that are a work based on
the Library side-by-side in a single library together with
other library facilities not covered by this License, and
distribute such a combined library, provided that the
separate distribution of the work based on the Library and
of the other library facilities is otherwise permitted, and
provided that you do these two things:
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms
of the Sections above.
b) Give prominent notice with the combined library of the
fact that part of it is a work based on the Library, and
explaining where to find the accompanying uncombined
form of the same work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the Library is void,
and will automatically terminate your rights under this
License. However, parties who have received copies,
or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full
compliance.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying or
distributing the Library (or any work based on the Library),
you indicate your acceptance of this License to do so,
and all its terms and conditions for copying, distributing or
modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based
on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link
with or modify the Library subject to these terms and
conditions. You may not impose any further restrictions
on the recipients’ exercise of the rights granted herein.
You are not responsible for enforcing compliance by third
parties with this License.
11. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from
the conditions of this License. If you cannot istribute so as
to satisfy simultaneously your obligations nder this License
and any other pertinent obligations, then as a consequence
you may not distribute the Library at all. For example, if a
patent license would not permit royalty free redistribution
of the Library by all those who receive copies directly or
indirectly through you, then the only way you could satisfy
both it and this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is intended
to apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose
of protecting the integrity of the free software distribution
system which is implemented by public license practices.
Many people have made generous contributions to the
wide range of software distributed through that system
in reliance on consistent application of that system; it is
up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee
cannot impose that choice. This section is intended to make
thoroughly clear what is believed to be a consequence of the
rest of this License.
12. If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
13. The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License
from time to time. Such new versions will be similar
in spirit to the present version, but may differ in detail
to address new problems or concerns. Each version
is given a distinguishing version number. If the Library
specifies a version number of this License which applies
to it and “any later version”, you have the option of
following the terms and conditions either of that version
or of any later version published by the Free Software
Foundation. If the Library does not specify a license
version number, you may choose any version ever
published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE LIBRARY
“AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
SHOULD THE LIBRARY PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE LIBRARY TO OPERATE WITH
ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries If you
develop a new library, and you want it to be of the greatest
possible use to the public, we recommend making it free
software that everyone can redistribute and change. You
can do so by permitting redistribution under these terms (or,
alternatively, under the terms of the ordinary General Public
License).
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each source
file to most effectively convey the exclusion of warranty;
and each file should have at least the “copyright” line and a
pointer to where the full notice is found. one line to give the
library’s name and an idea of what it does.
Copyright (C) year name of author
This library is free software; you can redistribute it and/ or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation;
either version 2.1 of the License, or (at your option) any later
version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
You should have received a copy of the GNU Lesser General
Public License along with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
Boston, MA 02110-1301 USA Also add information on how
to contact you by electronic and paper mail. You should also
get your employer (if you work as a programmer) or your
school, if any, to sign a “copyright disclaimer” for the library, if
necessary. Here is a sample; alter the names: Yoyodyne, Inc.,
hereby disclaims all copyright interest in the library ‘Frob’ (a
library for tweaking knobs) written by James Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice.
Open SSL LICENSE
Copyright (c) 1998-2006 The OpenSSL Project. All rights
reserved. Redistribution and use in source and binary forms,
with or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgment: “This
product includes software developed by the OpenSSL
Project for use in the OpenSSL Toolkit. (http:// www.
openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products derived
from this software without prior written permission.
For written permission, please contact openssl-core@
openssl.org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain
the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE. This product includes cryptographic
software written by Eric Young (eay@cryptsoft.com). This
product includes software written by Tim Hudson(tjh@
cryptsoft.com).
Original SSLEAY License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft. com)
All rights reserved. This package is an SSL implementation
written by Eric Young (eay@cryptsoft. com). The
implementation was written so as to conform with Netscapes
SSL. This library is free for commercial and non-commercial
use as long as the following conditions are aheared to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as such any Copyright
notices in the code are not to be removed. If this package
is used in a product, Eric Young should be given attribution
as the author of the parts of the library used. This can be
in the form of a textual message at program startup or in
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
“This product includes cryptographic software written by Eric
Young (eay@ cryptsoft.com)” The word ‘cryptographic’ can
be left out if the rouines from the library being used are not
cryptographic related :-).
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you
must include an acknowledgement: “This product includes
software written by Tim Hudson (tjh@ cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS
IS AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available
version or derivative of this code cannot be changed. i.e.
this code cannot simply be copied and put under another
distribution licence [including the GNU Public Licence.
BSD License
Some software components of this product incorporate source code covered under the BSD license as follows.
Component Name
License
URL
net-snmp-5.4
lighttpd 1.4.25
Game-ws
MiniUPnP Project Client
BSD
BSD 2.0
BSD 2.0
BSD 2.0
http://www.net-snmp.org/about/license.html
http://www.opensource.org/licenses/bsd-license.html
lighttpd is a secure, fast, compliant, and very flexible
webserver that has been optimized for high-performance
environments. It has a very low memory footprint compared
to other webservers and takes care of cpuload. Its advanced
feature-set (FastCGI, CGI, Auth, Output-
Compression, URL-Rewriting and many more) make lighttpd
the perfect webserver-software for every server that suffers
load problems. Simple Network Management Protocol
(SNMP) is an Internetstandard protocol for managing devices
on IP networks. It is used mostly in network management
systems to monitor the devices attached to the network for
conditions that need administrative attention. Net-SNMP is a
suite of applications used to implement SNMP v1, SNMP v2c
and SNMP v3 using both IPv4 and IPv6. For more additional
information, send email to help.cctv@samsung.com.
Copyright (C) 2004, Kneschke, incremental
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met :
-R
edistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
-R
edistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
-N
either the name of the ‘incremental’ nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1998-2001 University College London
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted provided that the following
conditions are met :
1. R
edistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. R
edistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. A
ll advertising materials mentioning features or use of this
software must display the following acknowledgement:
This product includes software developed by the
Computer Science Department at University College
London.
4. N
either the name of the University nor of the Department
may be used to endorse or promote products derived
from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND
CONTRIBUTORS ``AS IS’’ AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSEARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1991, 1993 The Regents of the University of
California.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. R
edistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. R
edistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. N
either the name of the Regents of the University of
California nor the names of its contributors may be used
to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 2006, Creative Labs Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of the Creative Labs nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 2005-2012, Thomas BERNARD
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of Thomas BERNARD nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Various copyrights apply to this package, listed in various
separate parts below. Please make sure that you read all the
parts.
Part 1: CMU/UCD copyright notice: (BSD like)
Copyright 1989, 1991, 1992 by Carnegie Mellon University
Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the University of
California
All Rights Reserved
Permission to use, copy, modify and distribute this software
and its documentation for any purpose and without fee is
hereby granted, provided that the above copyright notice
appears in all copies and that both that copyright notice and
this permission notice appear in supporting documentation,
and that the name of CMU and The Regents of the University
of California not be used in advertising or publicity pertaining
to distribution of the software without specific written
permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF
CALIFORNIA DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS.
IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES
OR ANY DAMAGES WHATSOEVER RESULTING FROM
THE LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION
WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Part 2: Networks Associates Technology, Inc copyright
notice (BSD)
Copyright (c) 2001-2003, Networks Associates Technology,
Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met: yy Redistributions of source
code must retain the above copyright notice, this list of
conditions and the following
disclaimer. yy Redistributions in binary form must reproduce
the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution. yy Neither the name
of the Networks Associates Technology, Inc nor the names of
its contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Portions of this code are copyright (c) 2001-2003, Cambridge
Broadband Ltd.
Copyright (c) 2003-2009, Sparta, Inc
Part 3: Cambridge Broadband Ltd. copyrightnotice (BSD)
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met: yy Redistributions of source
code must retain the above copyright notice, this list of
conditions and the following disclaimer. yy Redistributions
in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the
distribution. yy The name of Cambridge Broadband Ltd. may
not be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDER BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 4: Sun Microsystems, Inc. copyright notice
(BSD)
Copyright (c) 2003 Sun Microsystems, Inc., 4150 Network
Circle, Santa Clara, California 95054, U.S.A.
All rights reserved.
Use is subject to license terms below. This distribution
may include materials developed by third parties. Sun, Sun
Microsystems, the Sun logo and Solaris are trademarks
or registered trademarks of Sun Microsystems, Inc. in
the U.S. and other countries. Redistribution and use in
source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
yy Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer. yy Redistributions in binary form must reproduce
the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution. yy Neither the
name of the Sun Microsystems, Inc. nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
Part 5: Sparta, Inc copyright notice (BSD)
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met: yy Redistributions of source
code must retain the above copyright notice, this list of
conditions and the following disclaimer. yy Redistributions
in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the
distribution. yy Neither the name of Sparta, Inc nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 6: Cisco/BUPTNIC copyright notice (BSD)
Copyright (c) 2004, Cisco, Inc and Information Network
Center of Beijing University of Posts and Telecommunications.
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the following
conditions are met: yy Redistributions of source code must
retain the above copyright notice, this list of conditions
and the following disclaimer. yy Redistributions in binary
form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution. yy
Neither the name of Cisco, Inc, Beijing University of Posts
and Telecommunications, nor the names of their contributors
may be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 7: Fabasoft R&D Software GmbH & Co KG copyright
notice (BSD)
Copyright (c) Fabasoft R&D Software GmbH & Co KG,
2003oss@fabasoft.com
Author: Bernhard Penz
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met: yy Redistributions of source
code must retain the above copyright notice, this list of
conditions and the following disclaimer. yy Redistributions
in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the
distribution. yy The name of Fabasoft R&D Software GmbH
& Co KG or any of its subsidiaries, brand or product names
may not be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDER BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 8: Apple Inc. copyright notice (BSD)
Copyright (c) 2007 Apple Inc.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution. 3. Neither the name of
Apple Inc. (“Apple”) nor the names of its contributors may
be used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL APPLE OR ITSCONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 9: ScienceLogic, LLC copyright notice(BSD)
Copyright (c) 2009, ScienceLogic, LLC
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions aremet: yy Redistributions of source
code must retain the above copyright notice, this list of
conditions and the following disclaimer. yy Redistributions
in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the
distribution. yy Neither the name of ScienceLogic, LLC nor
the names of its contributors may be used to endorse or
promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE
The MIT License
Some software components of this product incorporate source code covered under the MIT license as follows
MIT License 2.0
- Acewidget, bettermeans, jquery-ui, libxml, libxml2, Mesa3D-MesaLib,mwEmbed,OpenGL Samples Pack, Wide Studio,
xorg-server
Copyright (c) 2011, The Dojo Foundation
Copyright 2010, AUTHORS.txt (http://jqueryui.com/about)
Dual licensed under the MIT or GPL Version 2 licenses.
- http://jquery.org/license
- http://docs.jquery.com/UI/Widget
Copyright Daniel Veillard
Copyright Igor Zlatovic <igor@zlatkovic.com>
Copyright Aleksey Sanin
Copyright Gary Pennington <Gary.Pennington@uk.sun.com>
Copyright Alfred Mickautsch <alfred@mickautsch.de>
Copyright Bjorn Reese <bjorn.reese@systematic.dk>
Copyright Joel W. Reed
Copyright William Brack <wbrack@mmm.com.hk>
Copyright (c) 2007-2010 The Khronos Group Inc.
Copyright Atish Kumar Patra
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to
use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the
following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of the
Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
The Independent JPEG Group’s JPEG Software
The software included in this product contains copyrighted software that is licensed under the JPEG license.
•• JPEG license
-- Code project – Generating Outline OpenGL, Libjpeg
This distribution contains the sixth public release of the
Independent JPEG Group’s free JPEG software. You are
welcome to redistribute this software and to use it for any
purpose, subject to the conditions under LEGAL ISSUES, below.
Serious users of this software (particularly those incorporating
it into larger programs) should contact IJG at jpeg-info@
uunet.uu.net to be added to our electronic mailing list. Mailing
list members are notified of updates and have a chance to
participate in technical discussions, etc.
This software is the work of Tom Lane, Philip Gladstone, Jim
Boucher, Lee Crocker, Julian Minguillon, Luis Ortiz, George
Phillips, Davide Rossi, Guido Vollbeding, Ge’ Weijers, and
other members of the Independent JPEG Group.
IJG is not affiliated with the official ISO JPEG standards
committee.
LEGAL ISSUES
============
In plain English:
1. We don’t promise that this software works. (But if you find
any bugs, please let us know!)
2. You can use this software for whatever you want. You
don’t have to pay us.
3. You may not pretend that you wrote this software. If you
use it in a program, you must acknowledge somewhere in
your documentation that you’ve used the IJG code.
In legalese:
The authors make NO WARRANTY or representation, either
express or implied, with respect to this software, its quality,
accuracy, merchantability, or fitness for a particular purpose.
This software is provided "AS IS", and you, its user, assume
the entire risk as to its quality and accuracy.
This software is copyright (C) 1991-1998, Thomas G. Lane.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and
distribute this software (or portions thereof) for any purpose,
without fee, subject to these conditions:
(1) If any part of the source code for this software is
distributed, then this README file must be included, with
this copyright and no-warranty notice unaltered; and any
additions, deletions, or changes to the original files must be
clearly indicated in accompanying documentation.
(2) If only executable code is distributed, then the
accompanying documentation must state that "this software
is based in part on the work of the Independent JPEG
Group".
(3) Permission for use of this software is granted only if
the user accepts full responsibility for any undesirable
consequences; the authors accept NO LIABILITY for
damages of any kind.
These conditions apply to any software derived from or
based on the IJG code, not just to the unmodified library. If
you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author’s
name or company name in advertising or publicity relating
to this software or products derived from it. This software
may be referred to only as "the Independent JPEG Group’s
software".
We specifically permit and encourage the use of this
software as the basis of commercial products, provided that
all warranty or liability claims are assumed by the product
vendor.
ansi2knr.c is included in this distribution by permission of L.
Peter Deutsch, sole proprietor of its copyright holder, Aladdin
Enterprises of Menlo Park, CA. ansi2knr.c is NOT covered by
the above copyright and conditions, but instead by the usual
distribution terms of the Free Software Foundation; principally,
that you must include source code if you redistribute it. (See
the file ansi2knr.c for full details.) However, since ansi2knr.
c is not needed as part of any program generated from the
IJG code, this does not limit you more than the foregoing
paragraphs do.
The Unix configuration script "configure" was produced
with GNU Autoconf. It is copyright by the Free Software
Foundation but is freely distributable. The same holds for its
supporting scripts (config.guess, config.sub, ltconfig, ltmain.
sh). Another support script, install-sh, is copyright by M.I.T.
but is also freely distributable.
It appears that the arithmetic coding option of the JPEG spec
is covered by patents owned by IBM, AT&T, and Mitsubishi.
Hence arithmetic coding cannot legally be used without
obtaining one or more licenses. For this reason, support for
arithmetic coding has been removed from the free JPEG
software. (Since arithmetic coding provides only a marginal
gain over the unpatented Huffman mode, it is unlikely that
very many implementations will support it.) So far as we are
aware, there are no patent restrictions on the remaining code.
The IJG distribution formerly included code to read and write
GIF files. To avoid entanglement with the Unisys LZW patent,
GIF reading support has been removed altogether, and the
GIF writer has been simplified to produce "uncompressed
GIFs". This technique does not use the LZW algorithm; the
resulting GIF files are larger than usual, but are readable by
all standard GIF decoders.
We are required to state that
"The Graphics Interchange Format(c) is the Copyright
property of CompuServe Incorporated. GIF(sm) is a Service
Mark property of CompuServe Incorporated."
Mozilla Public License
Since we, at Samsung Techwin, used the Mozilla Firefox component without modifying the source code according to the
MOZILLA Public license 1.1, we are not obliged to provide the source code of the corresponding component.
•• Version 1.1
1. Definitions.
1.0.1. "Commercial Use" means distribution or otherwise
making the Covered Code available to a third party.
1.1. ‘’Contributor’’ means each entity that creates or contributes
to the creation of Modifications.
1.2. ‘’Contributor Version’’ means the combination of the
Original Code, prior Modifications used by a Contributor, and the
Modifications made by that particular Contributor.
1.3. ‘’Covered Code’’ means the Original Code or Modifications
or the combination of the Original Code and Modifications, in
each case including portions thereof.
1.4. ‘’Electronic Distribution Mechanism’’ means a mechanism
generally accepted in the software development community for
the electronic transfer of data.
1.5. ‘’Executable’’ means Covered Code in any form other than
Source Code.
1.6. ‘’Initial Developer’’ means the individual or entity identified
as the Initial Developer in the Source Code notice required by
Exhibit A.
1.7. ‘’Larger Work’’ means a work which combines Covered
Code or portions thereof with code not governed by the terms
of this License.
1.8. ‘’License’’ means this document.
1.8.1. "Licensable" means having the right to grant, to the
maximum extent possible, whether at the time of the initial grant
or subsequently acquired, any and all of the rights conveyed
herein.
1.9. ‘’Modifications’’ means any addition to or deletion from
the substance or structure of either the Original Code or any
previous Modifications. When Covered Code is released as a
series of files, a Modification is:
A. A
ny addition to or deletion from the contents of a file
containing Original Code or previous Modifications.
B. A
ny new file that contains any part of the Original Code or
previous Modifications.
1.10. ‘’Original Code’’ means Source Code of computer
software code which is described in the Source Code notice
required by Exhibit A as Original Code, and which, at the time
of its release under this License is not already Covered Code
governed by this License.
1.10.1. "Patent Claims" means any patent claim(s), now owned
or hereafter acquired, including without limitation, method,
process, and apparatus claims, in any patent Licensable by
grantor.
1.11. ‘’Source Code’’ means the preferred form of the Covered
Code for making modifications to it, including all modules it
contains, plus any associated interface definition files, scripts
used to control compilation and installation of an Executable, or
source code differential comparisons against either the Original
Code or another well known, available Covered Code of the
Contributor’s choice. The Source Code can be in a compressed
or archival form, provided the appropriate decompression or
de-archiving software is widely available for no charge.
1.12. "You’’ (or "Your") means an individual or a legal entity
exercising rights under, and complying with all of the terms of,
this License or a future version of this License issued under
Section 6.1. For legal entities, "You’’ includes any entity which
controls, is controlled by, or is under common control with You.
For purposes of this definition, "control’’ means (a) the power,
direct or indirect, to cause the direction or management of
such entity, whether by contract or otherwise, or (b) ownership
of more than fifty percent (50%) of the outstanding shares or
beneficial ownership of such entity.
2. Source Code License.
2.1. The Initial Developer Grant. The Initial Developer hereby
grants You a world-wide, royalty-free, non-exclusive license,
subject to third party intellectual property claims:
(a) under intellectual property rights (other than patent
or trademark) Licensable by Initial Developer to use,
reproduce, modify, display, perform, sublicense and
distribute the Original Code (or portions thereof) with
or without Modifications, and/or as part of a Larger
Work; and
(b) under Patents Claims infringed by the making, using
or selling of Original Code, to make, have made, use,
practice, sell, and offer for sale, and/or otherwise dispose
of the Original Code (or portions thereof).
(c) the licenses granted in this Section 2.1(a) and (b) are
effective on the date Initial Developer first distributes
Original Code under the terms of this License.
(d) Notwithstanding Section 2.1(b) above, no patent license
is granted: 1) for code that You delete from the Original
Code; 2) separate from the Original Code; or 3) for
infringements caused by: i) the modification of the Original
Code or ii) the combination of the Original Code with
other software or devices.
2.2. Contributor Grant. Subject to third party intellectual property
claims, each Contributor hereby grants You a world-wide,
royalty-free, non-exclusive license
(a) under intellectual property rights (other than patent or
trademark) Licensable by Contributor, to use, reproduce,
modify, display, perform, sublicense and distribute the
Modifications created by such Contributor (or portions
thereof) either on an unmodified basis, with other
Modifications, as Covered Code and/or as part of a
Larger Work; and
(b) under Patent Claims infringed by the making, using, or
selling of Modifications made by that Contributor either
alone and/or in combination with its Contributor Version
(or portions of such combination), to make, use, sell,
offer for sale, have made, and/or otherwise dispose of:
1) Modifications made by that Contributor (or portions
thereof); and 2) the combination of Modifications made
by that Contributor with its Contributor Version (or
portions of such combination).
(c) the licenses granted in Sections 2.2(a) and 2.2(b) are
effective on the date Contributor first makes Commercial
Use of the Covered Code.
(d) Notwithstanding Section 2.2(b) above, no patent license is
granted: 1) for any code that Contributor has deleted from
the Contributor Version; 2) separate from the Contributor
Version; 3) for infringements caused by: i) third party
modifications of Contributor Version or ii) the combination of
Modifications made by that Contributor with other software
(except as part of the Contributor Version) or other devices;
or 4) under Patent Claims infringed by Covered Code in the
absence of Modifications made by that Contributor.
3. Distribution Obligations.
3.1. Application of License. The Modifications which You create
or to which You contribute are governed by the terms of this
License, including without limitation Section 2.2. The Source
Code version of Covered Code may be distributed only under
the terms of this License or a future version of this License
released under Section 6.1, and You must include a copy of this
License with every copy of the Source Code You distribute. You
may not offer or impose any terms on any Source Code version
that alters or restricts the applicable version of this License or
the recipients’ rights hereunder. However, You may include an
additional document offering the additional rights described in
Section 3.5.
3.2. Availability of Source Code. Any Modification which You
create or to which You contribute must be made available in
Source Code form under the terms of this License either on
the same media as an Executable version or via an accepted
Electronic Distribution Mechanism to anyone to whom you
made an Executable version available; and if made available
via Electronic Distribution Mechanism, must remain available
for at least twelve (12) months after the date it initially became
available, or at least six (6) months after a subsequent version
of that particular Modification has been made available to such
recipients. You are responsible for ensuring that the Source
Code version remains available even if the Electronic Distribution
Mechanism is maintained by a third party.
3.3. Description of Modifications. You must cause all Covered
Code to which You contribute to contain a file documenting the
changes You made to create that Covered Code and the date
of any change. You must include a prominent statement that the
Modification is derived, directly or indirectly, from Original Code
provided by the Initial Developer and including the name of the
Initial Developer in (a) the Source Code, and (b) in any notice in
an Executable version or related documentation in which You
describe the origin or ownership of the Covered Code.
3.4. Intellectual Property Matters
(a) Third Party Claims. If Contributor has knowledge that a
license under a third party’s intellectual property rights is
required to exercise the rights granted by such Contributor
under Sections 2.1 or 2.2, Contributor must include a text
file with the Source Code distribution titled "LEGAL’’ which
describes the claim and the party making the claim in
sufficient detail that a recipient will know whom to contact.
If Contributor obtains such knowledge after the Modification
is made available as described in Section 3.2, Contributor
shall promptly modify the LEGAL file in all copies Contributor
makes available thereafter and shall take other steps (such as
notifying appropriate mailing lists or newsgroups) reasonably
calculated to inform those who received the Covered Code
that new knowledge has been obtained.
(b) Contributor APIs. If Contributor’s Modifications include
an application programming interface and Contributor
has knowledge of patent licenses which are reasonably
necessary to implement that API, Contributor must also
include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to
Section 3.4(a) above, Contributor believes that Contributor’s
Modifications are Contributor’s original creation(s) and/or
Contributor has sufficient rights to grant the rights conveyed by
this License.
3.5. Required Notices. You must duplicate the notice in Exhibit
A in each file of the Source Code. If it is not possible to put
such notice in a particular Source Code file due to its structure,
then You must include such notice in a location (such as a
relevant directory) where a user would be likely to look for such a
notice. If You created one or more Modification(s) You may add
your name as a Contributor to the notice described in Exhibit
A. You must also duplicate this License in any documentation
for the Source Code where You describe recipients’ rights or
ownership rights relating to Covered Code. You may choose
to offer, and to charge a fee for, warranty, support, indemnity or
liability obligations to one or more recipients of Covered Code.
However, You may do so only on Your own behalf, and not on
behalf of the Initial Developer or any Contributor. You must make
it absolutely clear than any such warranty, support, indemnity or
liability obligation is offered by You alone, and You hereby agree
to indemnify the Initial Developer and every Contributor for any
liability incurred by the Initial Developer or such Contributor as a
result of warranty, support, indemnity or liability terms You offer.
3.6. Distribution of Executable Versions. You may distribute
Covered Code in Executable form only if the requirements of
Section 3.1-3.5 have been met for that Covered Code, and if
You include a notice stating that the Source Code version of
the Covered Code is available under the terms of this License,
including a description of how and where You have fulfilled the
obligations of Section 3.2. The notice must be conspicuously
included in any notice in an Executable version, related
documentation or collateral in which You describe recipients’
rights relating to the Covered Code. You may distribute the
Executable version of Covered Code or ownership rights under
a license of Your choice, which may contain terms different from
this License, provided that You are in compliance with the terms
of this License and that the license for the Executable version
does not attempt to limit or alter the recipient’s rights in the
Source Code version from the rights set forth in this License. If
You distribute the Executable version under a different license
You must make it absolutely clear that any terms which differ
from this License are offered by You alone, not by the Initial
Developer or any Contributor. You hereby agree to indemnify the
Initial Developer and every Contributor for any liability incurred by
the Initial Developer or such Contributor as a result of any such
terms You offer.
3.7. Larger Works. You may create a Larger Work by combining
Covered Code with other code not governed by the terms of
this License and distribute the Larger Work as a single product.
In such a case, You must make sure the requirements of this
License are fulfilled for the Covered Code.
4. Inability to Comply Due to Statute or Regulation.
If it is impossible for You to comply with any of the terms of this
License with respect to some or all of the Covered Code due to
statute, judicial order, or regulation then You must: (a) comply
with the terms of this License to the maximum extent possible;
and (b) describe the limitations and the code they affect. Such
description must be included in the LEGAL file described in
Section 3.4 and must be included with all distributions of the
Source Code. Except to the extent prohibited by statute or
regulation, such description must be sufficiently detailed for a
recipient of ordinary skill to be able to understand it.
5. Application of this License.
This License applies to code to which the Initial Developer has
attached the notice in Exhibit A and to related Covered Code.
6. Versions of the License.
6.1. New Versions. Netscape Communications Corporation
(‘’Netscape’’) may publish revised and/or new versions of
the License from time to time. Each version will be given a
distinguishing version number.
6.2. Effect of New Versions. Once Covered Code has been
published under a particular version of the License, You may
always continue to use it under the terms of that version. You
may also choose to use such Covered Code under the terms of
any subsequent version of the License published by Netscape.
No one other than Netscape has the right to modify the terms
applicable to Covered Code created under this License.
6.3. Derivative Works. If You create or use a modified version
of this License (which you may only do in order to apply it to
code which is not already Covered Code governed by this
License), You must (a) rename Your license so that the phrases
‘’Mozilla’’, ‘’MOZILLAPL’’, ‘’MOZPL’’, ‘’Netscape’’, "MPL", ‘’NPL’’
or any confusingly similar phrase do not appear in your license
(except to note that your license differs from this License) and (b)
otherwise make it clear that Your version of the license contains
terms which differ from the Mozilla Public License and Netscape
Public License. (Filling in the name of the Initial Developer,
Original Code or Contributor in the notice described in Exhibit
A shall not of themselves be deemed to be modifications of this
License.)
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON
AN "AS IS’’ BASIS, WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, WARRANTIES THAT THE COVERED CODE
IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A
PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
COVERED CODE IS WITH YOU. SHOULD ANY COVERED
CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT
THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR)
ASSUME THE COST OF ANY NECESSARY SERVICING,
REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY
CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO
USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER
EXCEPT UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This License and the rights granted hereunder will
terminate automatically if You fail to comply with terms herein
and fail to cure such breach within 30 days of becoming aware
of the breach. All sublicenses to the Covered Code which are
properly granted shall survive any termination of this License.
Provisions which, by their nature, must remain in effect beyond
the termination of this License shall survive.
8.2. If You initiate litigation by asserting a patent infringement
claim (excluding declatory judgment actions) against Initial
Developer or a Contributor (the Initial Developer or Contributor
against whom You file such action is referred to as "Participant")
alleging that:
(a) such Participant’s Contributor Version directly or indirectly
infringes any patent, then any and all rights granted by such
Participant to You under Sections 2.1 and/or 2.2 of this
License shall, upon 60 days notice from Participant terminate
prospectively, unless if within 60 days after receipt of notice
You either: (i) agree in writing to pay Participant a mutually
agreeable reasonable royalty for Your past and future use of
Modifications made by such Participant, or (ii) withdraw Your
litigation claim with respect to the Contributor Version against
such Participant. If within 60 days of notice, a reasonable
royalty and payment arrangement are not mutually agreed
upon in writing by the parties or the litigation claim is not
withdrawn, the rights granted by Participant to You under
Sections 2.1 and/or 2.2 automatically terminate at the
expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such
Participant’s Contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by
such Participant under Sections 2.1(b) and 2.2(b) are
revoked effective as of the date You first made, used, sold,
distributed, or had made, Modifications made by that
Participant.
8.3. If You assert a patent infringement claim against Participant
alleging that such Participant’s Contributor Version directly or
indirectly infringes any patent where such claim is resolved
(such as by license or settlement) prior to the initiation of patent
infringement litigation, then the reasonable value of the licenses
granted by such Participant under Sections 2.1 or 2.2 shall be
taken into account in determining the amount or value of any
payment or license.
8.4. In the event of termination under Sections 8.1 or 8.2
above, all end user license agreements (excluding distributors
and resellers) which have been validly granted by You or
any distributor hereunder prior to termination shall survive
termination.
9. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL
THEORY, WHETHER TORT (INCLUDING NEGLIGENCE),
CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL
DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY
DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER OF
ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR
ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES,
EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF
THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION
OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH
OR PERSONAL INJURY RESULTING FROM SUCH PARTY’S
NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS
SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND
LIMITATION MAY NOT APPLY TO YOU. 10. U.S. GOVERNMENT
END USERS.
The Covered Code is a ‘’commercial item,’’ as that term
is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
‘’commercial computer software’’ and ‘’commercial computer
software documentation,’’ as such terms are used in 48 C.F.R.
12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48
C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S.
Government End Users acquire Covered Code with only those
rights set forth herein.
11. MISCELLANEOUS.
This License represents the complete agreement concerning
subject matter hereof. If any provision of this License is held
to be unenforceable, such provision shall be reformed only to
the extent necessary to make it enforceable. This License shall
be governed by California law provisions (except to the extent
applicable law, if any, provides otherwise), excluding its conflictof-law provisions. With respect to disputes in which at least one
party is a citizen of, or an entity chartered or registered to do
business in the United States of America, any litigation relating
to this License shall be subject to the jurisdiction of the Federal
Courts of the Northern District of California, with venue lying in
Santa Clara County, California, with the losing party responsible
for costs, including without limitation, court costs and reasonable
attorneys’ fees and expenses. The application of the United
Nations Convention on Contracts for the International Sale
of Goods is expressly excluded. Any law or regulation which
provides that the language of a contract shall be construed
against the drafter shall not apply to this License.
12. RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is
responsible for claims and damages arising, directly or indirectly,
out of its utilization of rights under this License and You agree to
work with Initial Developer and Contributors to distribute such
responsibility on an equitable basis. Nothing herein is intended
or shall be deemed to constitute any admission of liability.
13. MULTIPLE-LICENSED CODE.
Initial Developer may designate portions of the Covered Code
as Multiple-Licensed. Multiple-Licensedmeans that the Initial
Developer permits you to utilize portions of the Covered Code
under Your choice of the MPL or the alternative licenses, if any,
specified by the Initial Developer in the file described in Exhibit A.
EXHIBIT A -Mozilla Public License.
``The contents of this file are subject to the Mozilla Public License
Version 1.1 (the "License"); you may not use this file except in
compliance with the License. You may obtain a copy of the
License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express
or implied. See the License for the specific language governing
rights and limitations under the License.
The Original Code is ___________________________________.
The Initial Developer of the Original Code is
________________________. Portions created by
______________________ are Copyright (C) ______
_______________________. All Rights Reserved.
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the
terms of the _____ license (the [___] License), in which case the
provisions of [______] License are applicable instead of those
above. If you wish to allow use of your version of this file only
under the terms of the [____] License and not to allow others to
use your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the
notice and other provisions required by the [___] License. If you
do not delete the provisions above, a recipient may use your
version of this file under either the MPL or the [___] License."
[NOTE: The text of this Exhibit A may differ slightly from the text
of the notices in the Source Code files of the Original Code. You
should use the text of this Exhibit A rather than the text found in
the Original Code Source Code for Your Modifications
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types
of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should
not be disposed of with other household waste at the end of their working life. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the
reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances
can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types
of waste and recycle them through your local, free battery return system.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325