Yamaha HTR-5835 Owner`s manual

U
HTR-5835
AV Receiver
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
i
11
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
IMPORTANT SAFETY INSTRUCTIONS
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool,
dry, clean place – away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 30 cm on the top,
20 cm on the left and right, and 20 cm on the back of
this unit.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in a environment with high humidity (i.e. a room with
a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing.
iii
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
CONTENTS
FEATURES............................................................. 2
GETTING STARTED............................................ 3
Supplied accessories .................................................. 3
Installing batteries in the remote control ................... 3
INTRODUCTION
INTRODUCTION
SOUND FIELD PROGRAMS
SOUND FIELD PROGRAM
DESCRIPTIONS...............................................48
For movie/video sources.......................................... 48
For music sources .................................................... 50
CONTROLS AND FUNCTIONS ......................... 4
ADVANCED OPERATION
PREPARATION
Front panel ................................................................. 4
Remote control........................................................... 6
Using the remote control ........................................... 7
Front panel display .................................................... 8
Rear panel ................................................................ 10
ADVANCED OPERATIONS ..............................51
Using the sleep timer ............................................... 51
Manually adjusting speaker levels........................... 52
SET MENU ............................................................53
PREPARATION
SPEAKER SETUP ............................................... 11
Speaker placement ................................................... 11
Speaker connections ................................................ 12
Before connecting components................................ 14
Connecting video components................................. 15
Connecting audio components................................. 18
Connecting the FM and AM antennas ..................... 19
Connecting the power supply cord .......................... 20
Turning on the power............................................... 20
REMOTE CONTROL FEATURES ...................60
Control area ............................................................. 60
Setting remote control codes ................................... 61
Controlling other components ................................. 62
ADDITIONAL INFORMATION
EDITING SOUND FIELD PARAMETERS ......63
Using the BASIC SETUP menu .............................. 21
What is a sound field ............................................... 63
Changing parameter settings ................................... 63
PLAYBACK.......................................................... 24
Basic operations....................................................... 24
Selecting sound field programs ............................... 26
Selecting input modes.............................................. 30
FM/AM TUNING ................................................. 32
SOUND FIELD PARAMETER
DESCRIPTIONS...............................................65
TROUBLESHOOTING .......................................67
RESETTING THE FACTORY PRESETS ........71
GLOSSARY...........................................................72
Audio formats .......................................................... 72
Sound field programs............................................... 73
Audio information ................................................... 73
Video signal information ......................................... 74
SPECIFICATIONS...............................................75
ADVANCED
OPERATION
Automatic and manual tuning.................................. 32
Presetting stations .................................................... 33
Selecting preset stations........................................... 35
Exchanging preset stations ...................................... 36
SOUND FIELD
PROGRAMS
BASIC SETUP ...................................................... 21
BASIC OPERATION
BASIC
OPERATION
CONNECTIONS .................................................. 14
Using SET MENU................................................... 54
1 SOUND MENU.................................................... 55
2 INPUT MENU...................................................... 57
3 OPTION MENU................................................... 58
XM SATELLITE RADIO TUNING .................. 38
ADDITIONAL
INFORMATION
What is XM Satellite Radio? ................................... 38
XM Satellite Radio connections .............................. 38
XM Satellite Radio functions .................................. 38
Activating XM Satellite Radio ................................ 39
Basic XM Satellite Radio operations....................... 40
XM Satellite Radio search modes............................ 41
Setting XM Satellite Radio preset channels ............ 44
RECORDING ....................................................... 47
1
FEATURES
FEATURES
Built-in 6-channel power amplifier
Sophisticated AM/FM tuner
◆ Minimum RMS output power
(0.9% THD, 1 kHz, 6 Ω)
Front: 120 W + 120 W
Center: 120 W
Surround: 120 W + 120 W
Subwoofer: 120 W (30 Hz, 6 Ω)
◆ 40-station random and direct preset tuning
◆ Automatic preset tuning
◆ Preset station shifting capability (preset editing)
Sound field features
◆ Proprietary YAMAHA technology for the creation of
sound fields
◆ Dolby Digital decoder
◆ DTS, DTS Neo: 6, DTS 96/24 decoder
◆ Dolby Pro Logic/Dolby Pro Logic II decoder
◆ Virtual CINEMA DSP
◆ SILENT CINEMA™
XM Satellite Radio
◆ XM Satellite Radio programming (using the “XM
Connect and Play digital antenna”, sold seperately)
Other features
◆ 192-kHz/24-bit D/A converter
◆ A SET MENU that provides you with items for
optimizing this unit for your audio/video system
◆ 6 additional input jacks for discrete multi-channel input
◆ Component video input/output capability
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Cinema and music night listening modes
◆ Remote control with preset remote control codes
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
2
“DTS”, “Neo:6” and “DTS 96/24” are registered trademarks of
Digital Theater Systems, Inc.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
GETTING STARTED
GETTING STARTED
INTRODUCTION
Supplied accessories
Please check that you received all of the following parts.
Remote control
Batteries (2)
(AA, R06, UM-3)
SYSTEM
POWER
POWER
TV
AV
STANDBY
POWER
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
AM loop antenna
Indoor FM antenna
MULTI CH IN
REC
AUDIO
DISC SKIP
CODE SET
AMP
TV
VOL
CH
MUTE
INPUT
VOLUME
MUTE
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
0
10
ENT.
SET MENU
LEVEL
TITLE
MENU
BAND
SRCH MODE
ENTER
A-E/CAT.
A-E/CAT.
RETURN
MEMORY
DISPLAY
PRESET/CH
Installing batteries in the remote
control
2
1
3
1
Press the
part and slide the battery
compartment cover off.
2
Insert two supplied batteries (AA, R06,
UM-3) according to the polarity markings
(+ / –) on the inside of the battery
compartment.
3
Slide the cover back until it snaps into place.
Notes on batteries
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not flash or its light becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the remote control code and program
any acquired functions that may have been cleared.
3
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
1
234 5
6
7
8
9
0
A
VOLUME
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
A/B/C/D/E
FM/AM
XM
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
B
C
DE
F
G
H
I
L
AUDIO
R
J
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
6 A/B/C/D/E, NEXT, CATEGORY*
Selects one of the 5 preset station groups (A to E) when
the unit is in tuner mode.
Selects the speaker channel to be adjusted when the unit is
not in tuner mode.
Note
7 PRESET/TUNING/ CH* l / h, LEVEL –/+
Selects preset station number 1 to 8 when the colon (:) is
displayed next to the band indication in the front panel
display when the unit is in tuner mode. Selects the tuning
frequency when the colon (:) is not displayed.
Adjusts the level of the speaker channel selected using
A/B/C/D/E (NEXT) when the unit is not in tuner mode.
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this unit.
4 PRESET/TUNING (EDIT), SEARCH MODE*
Switches the function of PRESET/TUNING/CH l / h,
LEVEL –/+ between selecting preset station numbers and
tuning.
5 FM/AM, XM*
Switches the reception band when the unit is in tuner
mode.
4
8 MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
9 TUNING MODE (AUTO/MAN’L MONO),
DISPLAY*
Switches between automatic tuning (AUTO indicator on)
and manual tuning (AUTO indicator off).
CONTROLS AND FUNCTIONS
INTRODUCTION
0 VIDEO AUX jacks
Input audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input source.
A VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
B
PHONES (SILENT CINEMA) jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down
to the left and right headphone channels.
C SPEAKERS A/B
Turns on or off the set of front speakers connected to the A
and/or B terminals on the rear panel each time the
corresponding button is pressed.
D STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
E TONE CONTROL
Use to adjust the bass/treble balance for the front left and
right speakers (see page 25).
F BASS/TREBLE –/+
Use to adjust the bass/treble balance for the front left and
right speakers (in conjunction with TONE CONTROL).
G PROGRAM l / h
Use to select sound field programs (see page 25).
H INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 30).
I INPUT selector
Selects the input source you want to listen to or watch.
J MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT
jacks. When selected, the MULTI CH INPUT source takes
priority over the source selected with INPUT (or the input
selector buttons on the remote control).
*
Available only when the unit is in the XM Satellite Radio
mode (see page 39).
5
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each control on the
remote control used to control this unit. To operate other
components, see “REMOTE CONTROL FEATURES” on
page 60.
1
SYSTEM
2
POWER
POWER
TV
AV
STANDBY
POWER
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
MULTI CH IN
REC
AUDIO
DISC SKIP
CODE SET
AMP
TV
3
4
7
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
5
6
8
STRAIGHT
10
ENT.
SET MENU
MENU
BAND
SRCH MODE
ENTER
A-E/CAT.
A-E/CAT.
RETURN
DISPLAY
PRESET/CH
C
DIRECT ST.
7
NIGHT
TITLE
MEMORY
B
E
INPUT
LEVEL
5
6
A
MUTE
MUTE
0
0
D
CH
9
9
VOLUME
VOL
A SPEAKERS B
8
F
G
H
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 Input selector buttons
Select the input source and change the control area.
3 Sound field program/numeric buttons
Use to select sound field programs.
Use numbers 1 through 8 to select preset stations when the
unit is in tuner mode.
Use SELECT to playback 2-channel sources in surround
(see page 28).
Use EXTD SUR. to turn on/off the extended surround
modes (see page 27).
Use DIRECT ST. to playback 2-channel sources in high
fidelity sound (see page 29).
4 SPEAKERS A/B
Use to turn on or off the set of front speakers connected to
the A and/or B terminals on the rear panel each time the
corresponding button is pressed.
5 LEVEL, BAND
Selects the speaker channel to be adjusted and sets the
level.
Switches the reception band when the unit is in tuner
mode.
6 Cursor buttons u / d / j / i /ENTER
Use to select and adjust sound field program parameters or
SET MENU items.
Press j / i to select a preset station group (A to E) when
the unit is in tuner mode.
Press u / d to select a preset station number (1 to 8)
when the unit is in tuner mode.
7 RETURN, MEMORY*
Returns to the previous menu level when adjusting the
SET MENU parameters.
8 STANDBY
Sets this unit in the standby mode.
9 SYSTEM POWER
Turns on the power of this unit.
0 SLEEP
Sets the sleep timer.
A MULTI CH IN
Selects multi-channel input when using an external
decoder (etc.).
B CODE SET
Use to set up remote control codes (see page 61).
6
CONTROLS AND FUNCTIONS
C AMP
Selects the AMP mode. You must select the AMP mode to
control the main unit.
E MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level.
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
VOLUME
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
F STRAIGHT, ENT.*
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
FM/AM
XM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
l
STRAIGHT
SPEAKERS
A
B
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
30
30
L
AUDIO
R
Approximately 6 m (20 ft)
SYSTEM
POWER
TV
G NIGHT
Turns on or off the night listening modes (see page 29).
POWER
MD/CD-R
DTV/CBL
Available only when the unit is in the XM Satellite Radio
mode (see page 39).
VCR
POWER
SLEEP
V-AUX
MULTI CH IN
AUDIO
CODE SET
AMP
VOL
TV MUTE
VOLUME
CH
TV INPUT
MUTE
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
*
TUNER
REC
STEREO
H SET MENU, SRCH MODE*
Activates the SET MENU function.
STANDBY
AV
CD
DVD
DISC SKIP
9
0
10
ENT.
SET MENU
LEVEL
TITLE
MENU
A/B/C/D/E
ENTER
RETURN
DISPLAY
PRESET/CH
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– places of high humidity, such as near a bath
– high temperature, such as near a heater or stove
– extremely low temperatures
– dusty places
7
INTRODUCTION
D VOLUME +/–
Increases or decreases the volume level.
Using the remote control
CONTROLS AND FUNCTIONS
Front panel display
1
2
t
96
24
MATRIX
q DIGITAL
VCR
4
5
V-AUX
6
DTV/CBL
7
DVD
8
MD/CD-R
90
TUNER
SP
AB
HiFi DSP
XM PTY HOLD PS PTY RT CT EON
SLEEP
dB
ft 96/24
DUAL L C R
mS LFE SL SB SR
dB
q PL x
D
E
F G
1 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
2 VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 30).
3 SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 25).
4 Input source indicators
A cursor lights to show the current input source.
5 Sound field indicators
Light to indicate the active DSP sound fields.
Presence DSP sound field
Listening position
Left surround
DSP sound field
Right surround
DSP sound field
Surround back DSP sound field
6 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
program.
7 AUTO indicator
Lights up to indicate that automatic tuning is possible.
8 TUNED indicator
Lights up when this unit is tuned into a station.
9 STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
8
B
CD
PCM
C
A
YPAO HD AUTO TUNED STEREO MEMORY MUTE VOLUME
VIRTUAL SILENT CINEMA
STANDARD ZONE2 NIGHT
q PL
q PL
3
H
I
J KL
M
0 MEMORY indicator
Flashes to show that a station can be stored.
A MUTE indicator
Flashes while the MUTE function is on.
B VOLUME level indication
Indicates the current volume level.
C PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
D STANDARD indicator
Lights up when Surround Standard or Surround Enhanced
is selected (see page 28).
E NIGHT indicator
Lights up when you select night listening mode.
F SP A B indicators
Light up according to the set of front speakers selected.
Both indicators light up when both sets of speakers are
selected.
G Headphones indicator
Lights up when headphones are connected.
H HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program.
I Multi-information display
Shows the current sound field program name and other
information when adjusting or changing settings.
J SLEEP indicator
Lights up while the sleep timer is on.
CONTROLS AND FUNCTIONS
K 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
INTRODUCTION
L LFE indicator
Lights up when the input signal contains the LFE signal.
M Input channel indicators/speaker indicators
Indicate the channel components of the current digital
input signal.
Indicate the number of speakers connected in SPEAKERS
(page 22), or indicate the channel being adjusted in
SP LEVEL (page 55).
9
CONTROLS AND FUNCTIONS
Rear panel
1
2
3
4
5
COMPONENT VIDEO
Y
PB
PR
DVD
MULTI CH INPUT
L
R
AUDIO
VIDEO
L
R
FRONT
OPTICAL
DTV
/CBL
XM
SWITCHED
TUNER
CENTER
SUB
WOOFER
IN
VCR
DVD
DTV/CBL
OUT
CD
R
AM
ANT
IN
(PLAY)
FRONT
SPEAKERS
L
R
+
– –
+ +
+
– –
+ +
SURROUND
L
– –
+
A
GND
MD/
CD-R
VIDEO
OUT
(REC)
CD
COAXIAL
AC OUTLETS
MONITOR
OUT
DTV/
CBL
SURROUND
DIGITAL
INPUT
VIDEO
DVD
SUB
WOOFER
MONITOR OUT
AUDIO
75Ω UNBAL.
B
FM
ANT
L
R
OUTPUT
– –
CENTER
6
7
8
+
SUB WOOFER
9
1 DIGITAL INPUT jacks
See pages 15, 17 and 18 for details.
6 Audio component jacks
See page 18 for connection information.
2 MULTI CH INPUT jacks
See page 16 for connection information.
7 SUBWOOFER OUTPUT jack
See page 13 for connection information.
3 Video component jacks
See pages 15 and 17 for connection information.
8 Antenna terminals
See page 19 for connection information.
4 XM jack
See page 39 for connection information.
9 Speaker terminals
See page 13 for connection information.
5 AC OUTLET(S)
Use to supply power to your other A/V components
(see page 20).
10
SPEAKER SETUP
SPEAKER SETUP
Surround speakers (SR and SL)
Speaker placement
The speaker layout below shows the standard ITU-R*
speaker setting. You can use it to enjoy CINEMA DSP
and multi-channel audio sources.
* ITU-R is the radio communication sector of the ITU
(International Telecommunication Union).
C
FR
30˚
SL
Subwoofer
The use of a subwoofer, such as the YAMAHA Active
Servo Processing Subwoofer System, is effective not only
for reinforcing bass frequencies from any or all channels,
but also for high fidelity reproduction of the LFE (lowfrequency effect) channel included in Dolby Digital and
DTS software. The position of the subwoofer is not so
critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of the
room to reduce wall reflections.
SR
60˚
SL
80˚
SR
1.8 m (6 ft)
Front speakers (FR and FL)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Align the front
face of the center speaker with the front face of your video
monitor. Place the speaker centrally between the front
speakers and as close to the monitor as possible, such as
directly over or under it.
11
PREPARATION
FL
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
SPEAKER SETUP
■ Banana plug connections
Speaker connections
Be sure to connect the left channel (L), right channel (R),
“+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the
polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
• Before connecting the speakers, make sure that the
power of this unit is off.
• Do not let the bare speaker wires touch each other or
do not let them touch any metal part of this unit. This
could damage this unit and/or speakers.
• Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals on this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
10 mm (3/8")
1
2
1
Remove approximately 10 mm (3/8") of
insulation from the end of each speaker
cable.
2
Twist the exposed wires of the cable together
to prevent short circuits.
3
Unscrew the knob.
4
Insert one bare wire into the hole in the side
of each terminal.
5
Tighten the knob to secure the wire.
3
4
5
Red: positive (+)
Black: negative (–)
12
First, tighten the knob and then insert the banana plug
connector into the end of the corresponding terminal.
Banana plug
SPEAKER SETUP
Front speakers (A)
Right
Left
Subwoofer
(with built-in amplifier)
Surround speakers
Right
Left
2
3
5
6
PREPARATION
FRONT
R
SPEAKERS
L
R
+
– –
+ +
+
– –
+ +
SURROUND
L
– –
+
A
SUB
WOOFER
B
OUTPUT
– –
Front
speakers
(B)
+
SUB WOOFER
CENTER
4
1
Center
speaker
Subwoofer
(SW-P3600 only)
■ FRONT terminals
Connect one or two speaker systems (2, 3) to these
terminals. If you use only one speaker system, connect it
to the FRONT A or B terminals.
■ CENTER terminals
4
Connect a center speaker (4) to these terminals.
■ SURROUND terminals
2
1
3
5
Connect surround speakers (5, 6) to these terminals.
■ SUBWOOFER terminals
6
Connect the YAMAHA SW-P3600 subwoofer to these
terminals.
■ SUBWOOFER jack
Connect a subwoofer with built-in amplifier, such as the
YAMAHA Active Servo Processing Subwoofer System,
to this jack when you do not use the YAMAHA SWP3600 subwoofer.
Speaker layout
13
CONNECTIONS
CONNECTIONS
Before connecting components
CAUTION
Do not connect this unit or other components to the mains
power until all connections between components are
complete.
Dust protection cap
Pull out the cap from the optical jack before you connect
the fiber optic cable. Do not discard the cap. When you are
not using the optical jack, be sure to put the cap back in
place. This cap protects the jack from dust.
■ Cable indications
■ Video jacks
For analog signals
left analog cables
L
right analog cables
R
This unit has two types of video jacks. Connection
depends on the availability of input jacks on your monitor.
VIDEO
COMPONENT VIDEO
PR
PB
Y
For digital signals
optical cables
coaxial cables
O
C
For video signals
video cables
V
PR
component video cables
PB
VIDEO jacks
For conventional composite video signals.
COMPONENT VIDEO jacks
For component signals, separated into luminance (Y) and
color difference (PB, PR) to provide the best quality in
picture reproduction.
Signal flow inside this unit
Y
Input
■ Analog jacks
You can input analog signals from audio components by
connecting audio pin cable to the analog jacks on this unit.
Connect red plugs to the right jacks and white plugs to the
left jacks.
■ Digital jacks
This unit has digital jacks for direct transmission of digital
signals through either coaxial or fiber optic cables. You
can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both
the COAXIAL and OPTICAL jacks, priority is given to
the input signals from the COAXIAL jack. All digital
input jacks are compatible with 96-kHz sampling digital
signals.
Note
This unit handles digital and analog signals independently. Thus
audio signals input to the analog jacks are only output to the
analog OUT (REC) jacks.
14
COMPONENT
VIDEO
VIDEO
Output
(MONITOR OUT)
CONNECTIONS
Connecting video components
■ Connections for DVD playback
Note
Be sure to connect your video source components in the same way you connect your video monitor to this unit. For example, if you
connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the VIDEO
connections.
PREPARATION
Video out
Optical out
DVD player
Audio out
R
O
V
L
PR
PB
Y
COMPONENT VIDEO
PB
Y
PR
DVD
AUDIO
R
VIDEO
L
VIDEO
DVD
MONITOR
OUT
Video in
Video
monitor
DIGITAL
INPUT
OPTICAL
DVD
VIDEO
MONITOR OUT
15
CONNECTIONS
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and
SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or preamplifier.
Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to
match the left and right outputs to the left and right input jacks for the front and surround channels.
MULTI CH INPUT
R
L
FRONT
SURROUND
CENTER
SUB
WOOFER
R
L
Subwoofer
out
R
L
Center
out
Front
out
Multi-format player/
External decoder
Surround
out
Notes
• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you
cannot select sound field programs.
• This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect at least a 5.1-channel speaker system before using this feature.
• When headphones are used, only front left and right channels are output.
16
CONNECTIONS
■ Connections for other video components
Note
Be sure to connect your video source components in the same way you connect your video monitor to this unit. For example, if you
connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the VIDEO
connections.
Video out
Optical out
Cable TV or
satellite tuner
O
R
V
L
PR
PB
PREPARATION
Audio out
Y
COMPONENT VIDEO
PB
Y
PR
AUDIO
VIDEO
L
R
VIDEO
DTV
/CBL
Video in
MONITOR
OUT
DTV/
CBL
Video
monitor
DIGITAL
INPUT
OPTICAL
IN
VCR
OUT
DTV/CBL
VIDEO
MONITOR OUT
R
L
R
L
Audio in
Audio out
V
Video in
DVD recorder
or VCR
Video out
■ VIDEO AUX jacks (on the front panel)
Use these jacks to connect any video source, such as a
game console or video camera, to this unit.
V
VIDEO AUX
VIDEO
L
V
L
AUDIO
R
R
Audio out R
Audio out L
Game
console or
video camera
Video out
17
CONNECTIONS
Connecting audio components
■ Connections for audio components
DIGITAL
INPUT
Audio out
L
CD player
R
CD
IN
(PLAY)
Coaxial out
MD/
CD-R
C
OUT
(REC)
CD
COAXIAL
L
R
AUDIO
R
L
R
Audio out
Audio in
MD recorder or
tape deck
18
L
CONNECTIONS
Connecting the FM and AM
antennas
Both FM and AM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
AM loop antenna
(included)
Indoor FM antenna
(included)
3
Orient the AM loop antenna
for the best reception.
Notes
TUNER
AM
ANT
GND
75Ω UNBAL.
FM
ANT
Ground (GND terminal)
For maximum safety and minimum interference,
connect the antenna GND terminal to a good earth
ground. A good earth ground is a metal stake driven
into moist earth.
■ Connecting the AM loop antenna
1
Set up the AM loop antenna, then connect it
to the terminals on this unit.
2
Press and hold the tab to insert
the AM loop antenna lead wires
into the AM ANT and GND
terminals.
19
PREPARATION
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. Consult the nearest
authorized YAMAHA dealer or service center about outdoor
antennas.
CONNECTIONS
Connecting the power supply cord
■ Connecting the AC power cord
Plug the power cord into an AC wall outlet.
Turning on the power
When all connections are complete, turn on the power of
this unit.
(U.S.A. model)
■ AC OUTLET(S) (SWITCHED).......2 outlets
Use these outlets to connect the power cords from your
other components to this unit. Power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). The outlet(s)
supply power to any connected component whenever this
unit is turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is 100 W.
■ Memory back-up
VOLUME
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
A/B/C/D/E
FM/AM
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
XM
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
h
PROGRAM
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
STANDBY/ON
The memory back-up circuit prevents the stored data from
being lost even if this unit is in the standby mode.
However if the power cord is disconnected from the AC
wall outlet, or the power supply is cut for more than one
week, the stored data will be lost.
SYSTEM
POWER
POWER
TV
AV
STANDBY
POWER
SYSTEM POWER
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
MULTI CH IN
REC
AUDIO
DISC SKIP
CODE SET
AMP
TV
Press STANDBY/ON (or SYSTEM POWER on the
remote control) to turn on the power of this unit.
SYSTEM
POWER
STANDBY
/ON
Front panel
20
or
Remote control
BASIC SETUP
BASIC SETUP
The basic setup feature is a useful way to set up your
system quickly and with minimal effort.
3
Press ENTER to enter BASIC SETUP.
y
• If you wish to configure the unit manually using more precise
adjustments, use the detailed parameters in SOUND MENU
(page 55) instead of using BASIC SETUP.
• Altering any parameters in BASIC SETUP will reset all
parameters in SOUND MENU.
• Initial settings are indicated in bold for each parameter.
ENTER
A-E/CAT.
PRESET/CH
VOL
CH
MUTE
INPUT
POWER
TV
AV
STANDBY
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
ENTERTAIN
3
4
EXTD SUR.
DIRECT ST.
5
6
A SPEAKERS B
MULTI CH IN
7
8
NIGHT
STRAIGHT
0
10
1
TITLE
MENU
SRCH MODE
ENTER
CODE SET
A-E/CAT.
AMP
ENT.
SET MENU
BAND
AUDIO
1
[U.S.A. and Canada models]
S (small)
16 x 13ft, 200ft2 (4.8 x 4.0m, 20m2)
M (medium) 20 x 16ft, 300ft2 (6.3 x 5.0m, 30m2)
L (large)
26 x 19ft, 450ft2 (7.9 x 5.8m, 45m2)
MOVIE
2
SELECT
LEVEL
REC
Select the size of the room you have installed your
speakers in. In general, the room sizes are defined as
follows:
MUTE
MUSIC
1
STANDARD
9
A-E/CAT.
RETURN
MEMORY
Press j / i to select the desired setting.
ROOM: S M >L
POWER
STEREO
DISC SKIP
4
VOLUME
SYSTEM
POWER
PREPARATION
The ROOM parameter appears in the front panel
display.
Using the BASIC SETUP menu
Before you begin:
• Press SPEAKERS A or B on the front panel (or press
AMP to select the AMP mode, then press SPEAKERS
A or B on the remote control) to select the front
speakers you want to use.
• Make sure you disconnect your headphones from this
unit.
A-E/CAT.
DISPLAY
2
3-13
[Other models]
S (small)
3.6 x 2.8m, 10m2
M (medium) 4.8 x 4.0m, 20m2
L (large)
6.3 x 5.0m, 30m2
PRESET/CH
TV
Press AMP.
5
AMP
Press d to display the SUBWOOFER
parameter.
ENTER
2
Press SET MENU.
“BASIC SETUP” appears in the front panel display.
SET MENU
MENU
SRCH MODE
A-E/CAT.
A-E/CAT.
PRESET/CH
BASIC SETUP
6
Press j / i to select the desired setting.
SUBWOOFER⋅⋅YES
YES
NONE
If you have a subwoofer in your system.
If you do not have a subwoofer in your system.
21
BASIC SETUP
7
Press d to display the SPEAKERS
parameter.
11
Press ENTER to confirm your selection.
ENTER
A-E/CAT.
A-E/CAT.
ENTER
A-E/CAT.
A-E/CAT.
PRESET/CH
PRESET/CH
8
If you selected SET, you hear a test tone from each
speaker in turn. “CHECK:TestTone” appears in the
front panel display for a few seconds, then “CHECK:
OK?”.
Press j / i to select the number of speakers
you connected.
Choices
SPEAKERS⋅⋅5spk
CHECK:TestTone
Display
CHECK OK? YES
2spk
L C R
SL SB SR
3spk
L C R
SL SB SR
4spk
L C R
SL SB SR
Speakers
Front L/R
12
Press j / i to select the desired setting.
Front L/R, Center
CHECK OK? YES
Front L/R, Surround L/R
YES
5spk
9
L C R
SL SB SR
Front L/R, Center, Surround L/R
NO
Press d to display SET/CANCEL.
13
To complete the setup process if the test tone
levels from each speaker were satisfactory.
To proceed to the SP LEVEL speaker level
adjustment menu to balance the level of each
speaker.
Press ENTER to confirm your selection.
ENTER
A-E/CAT.
A-E/CAT.
ENTER
A-E/CAT.
A-E/CAT.
PRESET/CH
PRESET/CH
10
Press j / i to select the desired setting.
>SET CANCEL
SET
CANCEL
22
To apply the settings you chose in steps
4 through 8.
To cancel the setup without making
any changes.
If you selected NO in step 12, the front speaker level
adjustment display appears in the front panel display.
BASIC SETUP
■ To balance the speaker levels
Perform the following steps after step 13 (see page 22).
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
SP
A
dB
mS
dB
L C R
SL
SR
The unit outputs the test tone from the selected speaker
and the left front (or left surround) speaker in turn. The
indicator of the speaker currently outputting the test tone
flashes in the front panel display.
Press d / u to select a speaker, then use j / i
to adjust the balance.
The control range is from +10 dB to –10 dB.
PREPARATION
14
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, if the power cord is disconnected from the
AC outlet, or the power supply is cut for more than one
week, the stored data will be lost. If so, adjust the
items again.
FR ----||---Adjusts the balance between the front left and right
speakers.
C ----||---Adjusts the balance between the front left and center
speakers.
SL ----||---Adjusts the balance between the front left and
surround left speakers.
SR ----||---Adjusts the balance between the surround left and
surround right speakers.
SWFR ----||---Adjusts the balance between the front left speaker
and the subwoofer.
15
Press SET MENU to exit after balancing the
speakers.
23
PLAYBACK
PLAYBACK
Basic operations
4
(U.S.A. model)
Select the input source.
Use INPUT (or press one of the input selector buttons
on the remote control) to select the input you desire.
INPUT
VOLUME
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
STANDBY
/ON
PRESET/TUNING
A/B/C/D/E
FM/AM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
or
TUNING MODE
CATEGORY
XM
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
l
STRAIGHT
SPEAKERS
A
B
PROGRAM
h
MULTI CH IN
REC
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
AUDIO
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
DISC SKIP
R
Front panel
CODE SET
Remote control
3
1
7
4
6
The current input source name and input mode appear
in the front panel display for a few seconds.
VCR
AMP
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
1
SP
A
TV
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
STANDBY
TUNER
SLEEP
VOL
CH
MUTE
INPUT
VOLUME
L
DVD
DTV/CBL
VCR
STEREO
V-AUX
MULTI CH IN
REC
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
7
3
AUDIO
DISC SKIP
3
A SPEAKERS B
CODE SET
9
0
10
SET MENU
LEVEL
AMP
TITLE
MENU
BAND
TV
ENT.
Selected input source
SYSTEM
Start playback or select a broadcast station
on the source component.
Refer to the operating instructions for the component.
6
Adjust the volume to the desired output level.
POWER
VOLUME
or
Front panel
Remote control
or
Turn on the video monitor connected to this
unit.
Press SPEAKERS A or B (or press AMP to
select the AMP mode, then press SPEAKERS
A or B on the remote control).
Each press turns the respective speakers on or off.
SPEAKERS
A
B
or
Front panel
24
5
Press STANDBY/ON (or SYSTEM POWER on
the remote control) to turn on the power.
STANDBY
/ON
3
Input mode
SRCH MODE
ENTER
2
R
MUTE
4
1
dB
6
POWER
AMP
A SPEAKERS B
9
Remote control
0
Front panel
VOLUME
Remote control
PLAYBACK
■ To adjust the tone
7
Select a sound field program if desired.
Press PROGRAM l / h repeatedly (or press AMP
to select the AMP mode, then press one of the sound
field program buttons on the remote control) to select
a sound field program. (See page 48 for details about
sound field programs.)
You can adjust the tonal quality
of your front left and right
speakers or headphones (when
connected).
Press TONE CONTROL on the
front panel repeatedly to select
TREBLE or BASS, then press
BASS/TREBLE –/+ repeatedly
to increase or decrease.
• Select TREBLE to adjust the
high frequency response.
• Select BASS to adjust the low frequency response.
TONE CONTROL
BASS/TREBLE
l
h
PROGRAM
Front panel
or
y
MUTE
AMP
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
A SPEAKERS B
9
0
LEVEL
7
8
NIGHT
STRAIGHT
10
ENT.
SET MENU
Remote control
“SILENT CINEMA” allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
surround, through ordinary headphones. “SILENT
CINEMA” activates automatically whenever you connect
headphones to the PHONES jack while listening to
CINEMA DSP or HiFi DSP sound field programs. When
activated, the “SILENT CINEMA” indicator lights up in
the front panel display.
Notes
• This unit will not be set to “SILENT CINEMA” when MULTI
CH INPUT is selected as the input source.
• “SILENT CINEMA” is not effective when the Direct Stereo or
2ch Stereo program is selected, or in STRAIGHT mode.
Notes
• If you increase or decrease the high-frequency or low-frequency
sound to an extreme level, the tonal quality of the surround
speakers may not match that of the front left and right speakers.
• TONE CONTROL is not effective with the Direct Stereo
program (page 29) or MULTI CH INPUT.
• When TC. BYPASS is set to AUTO (page 57), and BASS and
TREBLE are set to 0 dB, audio output automatically bypasses
this unit’s tone control circuitry.
■ To mute the sound
Press MUTE on the remote control.
The MUTE indicator flashes in the
front panel display.
To resume the audio output, press
MUTE again (or press VOLUME –/+).
The MUTE indicator disappears from
the display.
MUTE
y
You can adjust the muting level (see page 57).
25
BASIC
OPERATION
■ To listen with headphones
(“SILENT CINEMA”)
Speaker and headphone adjustments are stored independently.
PLAYBACK
■ Selecting MULTI CH INPUT
Press MULTI CH INPUT (or MULTI CH IN on the
remote control) so that “MULTI CH INPUT” appears in
the front panel display.
MULTI CH
INPUT
Selecting sound field programs
■ Front panel operation
MULTI CH IN
VOLUME
or
STANDBY
/ON
Front panel
Remote control
PRESET/TUNING
SEARCH MODE
A/B/C/D/E
FM/AM
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
XM
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
BASS/TREBLE
TONE CONTROL
VIDEO
SILENT CINEMA
L
AUDIO
R
MULTI CH INPUT
PROGRAM
Note
When “MULTI CH INPUT” is shown in the front panel display,
no other source can be played. To select another input source with
INPUT (or one of the input selector buttons), press MULTI CH
INPUT (or MULTI CH IN on the remote control) to turn off
“MULTI CH INPUT” in the front panel display.
Press PROGRAM l / h repeatedly to select the
desired program.
The name of the selected program appears in the front
panel display.
l
■ Playing video sources in the
background
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Use the input selector buttons on the remote
control to select a video source, then select an
audio source.
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
Audio sources
Video sources
MULTI CH IN
REC
AUDIO
DISC SKIP
CODE SET
Note
If you want to enjoy audio from the MULTI CH INPUT jacks
together with a video source, first select the video source, then
press MULTI CH INPUT (or MULTI CH IN on the remote
control).
26
VCR
V-AUX
PROGRAM
DTV/CBL
h
DVD
MD/CD-R
TUNER
CD
VOLUME
SP
A
HiFi DSP
TV Sports
Program name
dB
L
R
PLAYBACK
■ Remote control operation
■ Enjoying multi-channel software
TV
VOL
VOLUME
CH
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
STANDBY
POWER
TUNER
SLEEP
MUTE
INPUT
STEREO
MUSIC
MUTE
DVD
DTV/CBL
VCR
V-AUX
ENTERTAIN
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
MULTI CH IN
REC
AUDIO
DISC SKIP
0
10
Sound field
program
buttons
ENT.
SET MENU
LEVEL
CODE SET
TITLE
MENU
BAND
AMP
MOVIE
1
SRCH MODE
AMP
TV
DISPLAY
Press AMP to select the AMP mode, then press
one of the sound field program buttons
repeatedly to select the desired program.
The name of the selected program appears in the front
panel display.
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
DTV/CBL
DVD
0
MD/CD-R
7
8
NIGHT
STRAIGHT
10
TUNER
Off (OFF)
Plays back any signals without the extended surround
mode.
ENT.
BASIC
OPERATION
A SPEAKERS B
9
Auto (AUTO)
When the unit recognizes the flag of a 6.1-channel signal,
the unit automatically turns on extended surround mode.
If the unit does not recognize the flag of a 6.1-channel
signal, the extended surround mode turns off.
Matrix (MATRIX)
Plays back multi-channel signals with the extended
surround mode.
AMP
V-AUX
EXTD SUR.
A-E/CAT.
RETURN
VCR
AMP
7
ENTER
A-E/CAT.
Press AMP on the remote control to select the
AMP mode, then press EXTD SUR. to turn on the
extended surround mode (Auto or Matrix) using
the Matrix technology.
CD
VOLUME
SP
A
HiFi DSP
TV Sports
dB
L
R
Program name
y
Feel free to choose a sound field program based on your listening
preference, and not purely on the name of the program itself.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with that source.
• Sound field programs cannot be selected when MULTI CH
INPUT is selected.
• Sampling frequencies higher than 48 kHz (except for DTS 96/
24 signals) will be sampled down to 48 kHz, then sound field
programs will be applied.
27
PLAYBACK
When you select the SUR. STANDARD program:
Notes
• Some 6.1-channel compatible discs do not have the flag of a
6.1-channel signal which this unit can automatically detect. To
enjoy these kinds of discs with the extended surround mode,
select “MATRIX”.
• The extended surround mode is not available in the following
cases:
– When “SUR. LR” (see page 55) is set to NONE.
– When the source connected to the MULTI CH INPUT jack is
being played.
– When the source being played does not contain surround left
and right channel signals.
– When a Dolby Digital KARAOKE source is being played.
– When “2ch Stereo” or “Direct Stereo” is selected.
– When “AUTO” is selected while using STRAIGHT or one of
the SUR. STANDARD programs.
• When the power of this unit is turned off, this setting will be
reset to “AUTO”.
■ Enjoying 2-channel software in surround
Signals input from 2-channel sources can also be played
back on multiple channels.
Press AMP to select the AMP mode, then press
STANDARD on the remote control to switch
between the SUR. STANDARD and SUR.
ENHANCED programs.
AMP
STANDARD
5
Or press MOVIE to select the MOVIE THEATER
program.
MOVIE
4
Press SELECT on the remote control to select
the decoder.
SELECT
6
You can select from the following modes depending on
the type of software you are playing and your personal
preference.
28
PRO LOGIC
Dolby Pro Logic processing for any sources.
PLII Movie
Dolby Pro Logic II processing for movie software.
PLII Music
Dolby Pro Logic II processing for music software.
PLII Game
Dolby Pro Logic II processing for game software.
Neo:6 Cinema
DTS processing for movie software.
Neo:6 Music
DTS processing for music software.
When you select the SUR. ENHANCED or MOVIE
THEATER program:
PRO LOGIC
Dolby Pro Logic processing for any sources.
PLII Movie
Dolby Pro Logic II processing for movie software.
Neo:6 Cinema
DTS processing for movie software.
y
You can also select a decoder by pressing j / i on the remote
control when the decoder type is displayed in the front panel
display.
PLAYBACK
■ Listening to high fidelity stereo sound
(Direct Stereo)
Direct Stereo allows you to bypass this unit’s decoders and
DSP processors to enjoy pure high fidelity sound from 2channel PCM and analog sources.
Press j / i to adjust the effect level while
NIGHT:CINEMA or NIGHT:MUSIC is displayed.
This adjusts the level of compression.
Press PROGRAM l / h repeatedly (or press
AMP to select the AMP mode, then press DIRECT
ST.) to select “Direct Stereo”.
l
h
PROGRAM
A-E/CAT.
PRESET/CH
Remote control
DIRECT ST.
AMP
or
Front panel
ENTER
A-E/CAT.
8
Effect.Lvl:MID
Remote control
DIRECT STEREO
• Select MIN for minimum compression.
• Select MID for standard compression.
• Select MAX for maximum compression.
y
Notes
■ Night listening modes
The night listening modes are designed to improve
listenability at lower volumes or at night. Choose either
NIGHT:CINEMA or NIGHT:MUSIC depending on the
type of material you are playing.
Notes
• You cannot use the night listening modes with the Direct Stereo
program or MULTI CH INPUT (even though the NIGHT
indicator lights up when Direct Stereo is selected).
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
■ Downmixing to 2 channels
You can enjoy 2-channel stereo playback even from multichannel sources.
Press PROGRAM l / h repeatedly (or press
AMP to select the AMP mode, then press
STEREO on the remote control) to select 2ch
Stereo.
l
PROGRAM
h
STEREO
AMP
or
Press AMP to select the AMP mode, then press
NIGHT repeatedly on the remote control to select
cinema or music.
Front panel
1
Remote control
When night listening is selected, the NIGHT indicator in
the front panel display lights up.
AMP
2ch Stereo
NIGHT
10
y
You can use a subwoofer with this program when SWFR or
BOTH is selected in “BASS OUT”.
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music sources
to preserve ease-of-listening for all sounds.
• Select OFF if you do not want to use this function.
29
BASIC
OPERATION
• To avoid unexpected noise, do not play DTS-encoded CDs in
this mode.
• When multi-channel signals (Dolby Digital and DTS) are input,
this unit automatically switches to the corresponding analog
input. (When DTS is selected as an input mode, no sound will
be heard.)
• No sound will be output from the subwoofer.
• TONE CONTROL (page 25) and SET MENU (page 53)
settings are not effective.
• The front panel display automatically dims.
• If you press AMP on the remote control to select the AMP
mode, then press DIRECT ST., the unit automatically enters the
Direct Stereo mode and you cannot toggle between the unit's
other sound field programs.
NIGHT:CINEMA and NIGHT:MUSIC adjustments are stored
independently.
PLAYBACK
■ Listening to unprocessed input signals
In STRAIGHT mode, two channel stereo sources are
output from only the front left and right speakers. Multichannel sources are decoded straight into the appropriate
channels without any additional effect processing.
Press STRAIGHT (or press AMP to select the
AMP mode, then press STRAIGHT on the remote
control) to select STRAIGHT.
Selecting input modes
This unit comes with a variety of input jacks. Do the
following to select the type of input signals you want to
use.
1
Rotate INPUT to select the input source.
INPUT
AMP
STRAIGHT
EFFECT
STRAIGHT
ENT.
or
Front panel
Remote control
2
STRAIGHT
Press INPUT MODE to select an input mode.
In most cases, use AUTO.
INPUT MODE
Press STRAIGHT (EFFECT) (or STRAIGHT (ENT.) on
the remote control) again so that “STRAIGHT”
disappears from the display when you want to turn the
sound effect back on.
■ Virtual CINEMA DSP
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
SP
A
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers. It creates
virtual speakers to reproduce the natural sound field.
If you set “SUR. LR” to NONE (see page 55), Virtual
CINEMA DSP activates automatically whenever you
select a CINEMA DSP sound field program.
dB
L
Input source
AUTO
Note
Virtual CINEMA DSP will not activate, even when “SUR. LR” is
set to NONE (see page 55) in the following cases:
– When MULTI CH INPUT is selected as the input source.
– When headphones are connected to the PHONES jack.
DTS
ANALOG
R
Input mode
Automatically selects input signals in
the following order:
1) Digital signals*
2) Analog signals
Selects only digital signals encoded in
DTS. If no DTS signals are input, no
sound is output.
Selects only analog signals. If no
analog signals are input, no sound is
output.
* If this unit detects a Dolby Digital or DTS signal, the
decoder automatically switches to the appropriate
decoder.
y
You can adjust the default input mode of this unit (see page 58).
30
PLAYBACK
Notes
3
• When playing a DTS-CD/LD, be sure to set the INPUT MODE
to DTS.
• If the digital output data of the player has been processed in any
way, you may not be able to perform DTS decoding even if you
make a digital connection between this unit and the player
depending on the player.
Press u / d to display the following
information about the input signal.
ENTER
A-E/CAT.
■ Displaying information about the input
source
PRESET/CH
You can display the type, format and sampling frequency
of the current input signal.
(Format)
1
in
Select the input source.
CD
MD/CD-R
TUNER
DVD
DTV/CBL
VCR
SLEEP
V-AUX
MULTI CH IN
REC
fs
AUDIO
DISC SKIP
CODE SET
rate
Press AMP to select the AMP mode, then
press STRAIGHT so that “STRAIGHT”
appears in the display.
AMP
flg
Signal format display. When the unit
cannot detect a digital signal it
automatically switches to analog input.
Number of source channels in the input
signal. For example, a multi-channel
soundtrack with 3 front channels, 2
surround channels and LFE, is
displayed as “3/2/LFE”.
Sampling frequency. When the unit is
unable to detect the sampling
frequency “Unknown” appears.
Bit rate. When the unit is unable to
detect the bit rate “Unknown” appears.
Flag data encoded with DTS or Dolby
Digital signals that cue this unit to
automatically switch decoders.
STRAIGHT
ENT.
then
STRAIGHT
31
BASIC
OPERATION
2
A-E/CAT.
FM/AM TUNING
FM/AM TUNING
Automatic and manual tuning
3
There are 2 tuning methods; automatic and manual.
Automatic tuning is effective when station signals are
strong and there is no interference.
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator lights up in the
front panel display.
TUNING MODE
AUTO
DISPLAY
■ Automatic tuning
Lights up
AUTO/MAN'L MONO
3 2
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
VOLUME
PRESET/TUNING
STANDBY
/ON
SEARCH MODE
PRESET/TUNING
SEARCH MODE
FM/AM
XM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
EDIT
DISPLAY
NEXT
EDIT
TUNING MODE
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
4
1
L
AUDIO
R
VCR
1 3
Rotate INPUT to select TUNER as the input
source.
INPUT
V-AUX
DTV/CBL
MD/CD-R
DVD
TUNER
AUTO TUNED
SP
A
4
Press PRESET/TUNING/CH l / h once to
begin automatic tuning.
Press h to tune into a higher frequency, or press l
to tune into a lower frequency.
l PRESET/TUNING/CH h
LEVEL
2
Press FM/AM to select the reception band.
“FM” or “AM” appears in the front panel display.
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
AUTO TUNED
SP
A
FM/AM
FM
32
or
AM
When tuned into a station, the TUNED indicator
lights up and the frequency of the received station is
shown in the front panel display.
FM/AM TUNING
■ Manual tuning
If the signal from the station you want to select is weak,
tune into it manually. Manually tuning into an FM station
will automatically switch the tuner to monaural reception
to increase the signal quality.
1
Select TUNER and the reception band
following steps 1 and 2 as described in
“Automatic tuning”.
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator disappears from
the front panel display.
Presetting stations
■ Automatically presetting FM stations
You can use the automatic preset tuning feature to store
FM stations. This function enables this unit to
automatically tune into FM stations with strong signals,
and to store up to 40 (8 stations in 5 groups, A1 through
E8) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
1
3 2
VOLUME
AUTO
TUNING MODE
DISPLAY
STANDBY
/ON
PRESET/TUNING
Disappears
AUTO/MAN'L MONO
SEARCH MODE
FM/AM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
XM
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
1
PRESET/TUNING
BASIC
OPERATION
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
Press FM/AM to select the FM band.
SEARCH MODE
EDIT
FM/AM
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
FM
TUNER
AUTO
SP
A
3
Press PRESET/TUNING/CH l / h to tune
into the desired station manually.
Hold down the button to
continue searching.
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator lights up in the
front panel display.
l PRESET/TUNING/CH h
TUNING MODE
AUTO
LEVEL
DISPLAY
Lights up
AUTO/MAN'L MONO
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
PRESET/TUNING
SEARCH MODE
EDIT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
AUTO
SP
A
33
FM/AM TUNING
■ Manually presetting stations
3
Press and hold MEMORY (MAN’L/AUTO FM)
for more than 3 seconds.
The preset number, the MEMORY and AUTO
indicators flash. After about 5 seconds, automatic
presetting starts from the frequency currently
displayed and proceeds toward the higher
frequencies.
You can also store up to 40 stations (8 stations x 5 groups)
manually.
3
2,5
VOLUME
STANDBY
/ON
MEMORY
PRESET/TUNING
SEARCH MODE
A/B/C/D/E
FM/AM
XM
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
MAN'L/AUTO FM
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
BASS/TREBLE
TONE CONTROL
VIDEO
SILENT CINEMA
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
AUTO TUNED
CD
MEMORY
dB
L
AUDIO
R
4
VOLUME
SP
A
L
R
1
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
Tune into a station.
See page 32 for tuning instructions.
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
VOLUME
SP
A
dB
L
Notes
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• If the number of received stations does not reach 40 (E8),
automatic preset tuning has automatically stopped after
searching all stations.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually
and store it by following the procedure in “Manually presetting
stations”.
R
When tuned into a station, the front panel display
shows the frequency of the station received.
2
Press MEMORY (MAN’L/AUTO FM).
The MEMORY indicator flashes for about 5 seconds.
MEMORY
MEMORY
MAN'L/AUTO FM
Automatic preset tuning options:
You can select the preset number from which this unit will
store FM stations and/or begin tuning toward lower
frequencies.
After pressing MEMORY in step 3:
1 Press A/B/C/D/E, then PRESET/TUNING/CH l / h
to select the preset number under which the first station
will be stored. Automatic preset tuning will stop when
stations have all been stored up to E8.
2 Press PRESET/TUNING (EDIT) to turn off the colon
(:) and then press PRESET/TUNING/CH l to begin
tuning toward the lower frequencies.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the preset stations may be cleared. If
so, store the stations again by using the presetting
station methods.
34
Flashes
3
Press A/B/C/D/E (NEXT) repeatedly to select
a preset station group (A to E) while the
MEMORY indicator is flashing.
The group letter appears. Check that the colon (:)
appears in the front panel display.
A/B/C/D/E
CATEGORY
NEXT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
VOLUME
SP
A
dB
L
Preset group
R
FM/AM TUNING
4
Press PRESET/TUNING/CH l / h to select a
preset station number (1 to 8) while the
MEMORY indicator is flashing.
Press h to select a higher preset station number.
Press l to select a lower preset station number.
Selecting preset stations
You can tune any desired station simply by selecting the
preset station number under which it was stored.
1 2
l PRESET/TUNING/CH h
VOLUME
LEVEL
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
A/B/C/D/E
FM/AM
XM
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
STRAIGHT
SPEAKERS
A
B
PROGRAM
h
VIDEO AUX
INPUT MODE
CD
MEMORY
l
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
dB
L
R
Preset number
A SPEAKERS B
9
NIGHT
0
10
STRAIGHT
ENT.
LEVEL
SET MENU
TITLE
MENU
BAND
5
MULTI CH
INPUT
EFFECT
TONE CONTROL
VOLUME
SP
A
1
SRCH MODE
ENTER
MEMORY
A-E/CAT.
A-E/CAT.
RETURN
MEMORY
DISPLAY
PRESET/CH
2
BASIC
OPERATION
Press MEMORY (MAN’L/AUTO FM) on the
front panel while the MEMORY indicator is
flashing.
The station band and
frequency appear in the front
panel display with the preset
group and number you have
selected.
y
When performing this operation with the remote control, first
press TUNER to set the remote to tuner mode.
MAN'L/AUTO FM
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
VOLUME
SP
A
dB
L
R
1
Press A/B/C/D/E (NEXT) (or A-E/CAT. j / i on
the remote control) to select the preset
station group.
The preset group letter appears in the front panel
display and changes each time you press the button.
Shows the displayed station has been stored as C3.
6
Repeat steps 1 to 5 to store other stations.
A/B/C/D/E
or
CATEGORY
NEXT
Notes
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
Front panel
ENTER
A-E/CAT.
A-E/CAT.
PRESET/CH
Remote control
35
FM/AM TUNING
2
Press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control) to
select a preset station number (1 to 8).
The preset group and number appear in the front
panel display along with the station band, frequency
and the TUNED indicator lights up.
Exchanging preset stations
You can exchange the assignment of two preset stations
with each other. The example below describes the
procedure for exchanging preset station “E1” with “A5”.
2,4 1,3 1,3
l PRESET/TUNING/CH h
VOLUME
or
ENTER
LEVEL
A-E/CAT.
STANDBY
/ON
A-E/CAT.
PRESET/TUNING
Front panel
A/B/C/D/E
FM/AM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
XM
TUNING MODE
DISPLAY
NEXT
EDIT
PRESET/CH
AUTO/MAN'L MONO
INPUT
PHONES
l
STRAIGHT
SPEAKERS
A
B
h
PROGRAM
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
Remote control
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
SP
A
CD
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
AUDIO
R
1
Select preset station “E1”.
See “Selecting preset stations”.
2
Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
PRESET/TUNING
SEARCH MODE
EDIT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
SP
A
36
L
CD
MEMORY
FM/AM TUNING
3
Select preset station “A5” using A/B/C/D/E
and PRESET/TUNING/CH l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
l PRESET/TUNING/CH h
A/B/C/D/E
CATEGORY
LEVEL
NEXT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
SP
A
4
Press PRESET/TUNING (EDIT) again.
The stations stored at the two preset assignments are
exchanged.
PRESET/TUNING
BASIC
OPERATION
SEARCH MODE
EDIT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
SP
A
37
XM SATELLITE RADIO TUNING
XM SATELLITE RADIO TUNING
What is XM Satellite Radio?
XM Satellite Radio is the satellite radio service with millions of listeners
across the U.S., broadcasting live daily. XM’s channel lineup includes more
than 130 digital channels of choice from coast to coast: 68 commercial-free
music channels, featuring hip hop to opera, classical to country, bluegrass to
blues; 33 channels of premier sports, talk, comedy, children’s and
entertainment programming; and more than 20 channels of the traffic and
weather information for major metropolitan areas nationwide.
Because XM Satellite Radio is a subscription service, you will
need to set up an account and activate service with XM using your
XM Satellite Radio ID number. To check your ID number, follow
“Activating XM Satellite Radio” on page 39. For further
information on XM Satellite Radio services, see the XM Satellite
Radio website at “http://www.xmradio.com”.
XM Satellite Radio functions
This section describes the functions of each control used
for XM Satellite Radio tuning.
■ Front panel functions
Note
The following controls are only available when the unit is in the
TUNER mode and the XM Connect and Play digital antenna is
connected to the XM jack on the rear of this unit. (For details, see
“XM Satellite Radio connections”.)
PRESET/TUNING
SEARCH MODE
FM/AM
XM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
Notes
• The XM Satellite Radio service is only available in the 48
contiguous United States (not available in Alaska and Hawaii).
• XM Connect and Play digital antenna and monthly subscription are sold
separately. For details, see the XM Satellite Radio website at “http://
www.xmradio.com”.
XM Satellite Radio connections
■ Connecting the XM Connect and Play
digital antenna
Connect the XM Connect and Play digital antenna (sold
separately) to the XM jack on the rear of this unit. (For details,
see the operating instructions provided with the XM Connect
and Play digital antenna.)
XM jack
XM
Notes
• For information on obtaining the XM Connect and Play digital
antenna, see the website at “http://www.xmradio.com” or visit
your local retailer that sells XM Ready products.
• To ensure optimal reception of XM’s satellite signal, the XM Connect and
Play digital antenna should be placed at or near a southerly facing window
with nothing obstructing its path to the sky. You can mount it indoors or
outdoors.
38
1 2
3
4
5
6
1 SEARCH MODE
Switches between the All Channel Search, Category Search, and Preset Search
modes. (For details, see “XM Satellite Radio search modes” on page 41.)
2 XM
Switches the reception band between AM, FM and XM.
3 CATEGORY
(All Channel Search mode)
Changes the channel category to next one (while staying
in the All Channel Search mode).
(Category Search mode)
Changes the channel category to next one.
(Preset Search mode)
Switches between five preset groups (A to E).
4 PRESET/TUNING/CH l / h
(All Channel Search mode)
Searches a radio channel within all channels. Press and
hold for quick search.
(Category Search mode)
Searches a radio channel within the selected category.
Press and hold for quick search.
(Preset Search mode)
Changes the preset number (1 to 8).
5 MEMORY
Switches the unit to the preset memory mode.
6 DISPLAY
Switches XM information such as channel number/name, category,
or artist name/song title displayed in the front panel display. (For
details, see “Switching XM information” on page 41.)
XM SATELLITE RADIO TUNING
■ Remote control functions
Activating XM Satellite Radio
Note
The following controls are only available when the unit is in the
TUNER mode. To switch to the TUNER mode, press TUNER to
select TUNER as the input source.
VOLUME
VOL
CH
MUTE
INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
MUTE
1
MOVIE
VOLUME
A SPEAKERS B
9
2
3
4
To sign up for an account with the XM Satellite Radio
service, an XM Satellite Radio ID number is required.
Follow the procedure below to check your ID number, and
then access the website at “http://activate.xmradio.com”
or call “1-800-XM-RADIO (1-800-967-2346)” with a
major credit card for signing up.
0
10
ENT.
SET MENU
LEVEL
TITLE
MENU
BAND
SRCH MODE
5
6
STANDBY
/ON
PRESET/TUNING
MEMORY
DISPLAY
PRESET/CH
A/B/C/D/E
7
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
A-E/CAT.
RETURN
FM/AM
XM
SEARCH MODE
ENTER
A-E/CAT.
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
2
1
4 MEMORY
Switches the unit to the preset memory mode.
5 ENT.
Confirms an entered channel number during the Direct
Number Access mode (see page 43).
6 SRCH MODE
Switches between the All Channel Search, Category
Search, and Preset Search modes. (For details, see “XM
Satellite Radio search modes” on page 41.)
R
1
Rotate INPUT (or press TUNER on the remote
control) to select TUNER as the input source.
INPUT
2 BAND
Switches the reception band between the currently
selected band (AM or FM) and XM.
3 Cursor buttons u / d / j / i
(All Channel Search mode)
Press A-E/CAT. j / i to change the channel category.
Press PRESET/CH u / d to search a radio channel
within all channels. Press and hold for quick search.
(Category Search mode)
Press A-E/CAT. j / i to change the channel category.
Press PRESET/CH u / d to search a radio channel within
the selected category. Press and hold for quick search.
(Preset Search mode)
Press A-E/CAT. j / i to change the preset group (A to E).
Press PRESET/CH u / d to change the preset number
(1 to 8).
3
AUDIO
TUNER
or
Front panel
2
Remote control
Press XM (or BAND on the remote control) to
select “XM” as the reception band.
FM/AM
LEVEL
or
XM
TITLE
BAND
Front panel
VCR
V-AUX
Remote control
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
SP
A
XM
XM RADIO
Lights
If “CHECK ANTENNA” appears in the front panel
display, the XM Connect and Play digital antenna
may not be connected to the XM jack on the rear of
this unit properly. See “XM Satellite Radio
connections” on page 38 and check the connection.
7 DISPLAY
Switches XM information such as channel number/name,
category, or artist name/song title displayed in the front
panel display. (For details, see “Switching XM
information” on page 41.)
39
BASIC
OPERATION
1 Numeric buttons
(All Channel Search or Category Search mode)
Use 1 to 9 and 0 to enter a channel number directly.
(Preset Search mode)
Use 1 to 8 to enter a preset channel number directly.
L
XM SATELLITE RADIO TUNING
3
Press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control) to
select channel “0”.
Basic XM Satellite Radio
operations
■ Selecting the XM Satellite Radio mode
PRESET/CH
l PRESET/TUNING/CH h
or
ENTER
LEVEL
A-E/CAT.
A-E/CAT.
l P
A/B/C/D/E
FM/AM
PRESET/TUNING
XM
SEARCH MODE
RESET/TUNING/CH
h
MEMORY
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
LEVEL
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
Front panel
Remote control
STRAIGHT
l
P
ROGRAM
h
INPUT MODE
TONE CONTROL
MULTI CH
INPUT
BASS/TREBLE
Note
You cannnot select channel “0” if the “All Channel Search mode”
(see page 41) is not selected.
4
Check the XM Satellite Radio ID number
displayed in the front panel display and write
it down.
1
2
1
Rotate INPUT (or press TUNER on the remote
control) to select TUNER as the input source.
INPUT
ID:_____________________________________
TUNER
or
Front panel
2
Remote control
Press XM (or BAND on the remote control) to
select “XM” as the reception band.
Information (such as channel number/name, category,
or artist name/song title) for the channel currently
selected appears in the front panel display and the
XM indicator lights up.
LEVEL
FM/AM
or
XM
TITLE
BAND
Remote control
Front panel
VCR
V-AUX
SP
A
DTV/CBL
DVD
MD/CD-R
TUNER
XM
[001] Preview
CD
Lights
y
• Selecting the “XM” band automatically recalls the channel
previously selected.
• You can change the kind of XM information by pressing
DISPLAY repeatedly. (For details, see “Switching XM
information” on page 41.)
Note
XM satellite Radio signals cannot be output from the AUDIO
OUT (REC) jacks.
40
XM SATELLITE RADIO TUNING
■ Switching XM information
You can display XM information (such as channel
number/name, category, or artist name/song title) for the
channel currently selected in the front panel display.
Press DISPLAY on the unit (or remote control
during the TUNER mode) repeatedly to toggle
between the following XM information display
modes.
XM Satellite Radio search modes
You can search for the channel you want to listen to using
one of three search modes. You can also enter the number
directly to select the desired channel. (For details, see
“Direct Number Access mode” on page 43.)
■ All Channel Search mode
TUNING MODE
Channel name/number
DISPLAY
AUTO/MAN'L MONO
Front panel
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
Channel category
or
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
STRAIGHT
DISPLAY
l
PROGRAM
h
INPUT MODE
Artist name/Song title
Remote control
TONE CONTROL
MULTI CH
INPUT
BASS/TREBLE
When the channel number/name is displayed:
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
2
CD
[040] Deep Tra
1
Carry out “Selecting the XM Satellite Radio
mode” on page 40.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select “ALL
CH SEARCH”.
When the channel category is displayed:
VCR
V-AUX
3
XM
DTV/CBL
DVD
SP
A
MD/CD-R
TUNER
CD
XM
<CAT>Rock
When the artist name/song title is displayed:
SET MENU
PRESET/TUNING
VCR
V-AUX
SP
A
DTV/CBL
DVD
MD/CD-R
TUNER
CD
XM
Coldplay / Clo
y
• The front panel display can indicate up to 14 alphanumeric
characters at once. If the information contains more than 14
characters, the information scrolls from right to left.
• If the information contains a character that cannot be
recognized by the unit, the character will be displayed with an
underbar “_”.
MENU
or
SEARCH MODE
SRCH MODE
EDIT
Front panel
VCR
V-AUX
Remote control
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
SP
A
XM
ALL CH SEARCH
Note
If a status message or an error message appears in the display, see
“Status and error messages” on page 46.
41
BASIC
OPERATION
SP
A
XM SATELLITE RADIO TUNING
■ Category Search mode
3
To change the channel category, press
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
PRESET/TUNING
PRESET/CH
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
NEXT
AUTO/MAN'L MONO
INPUT
A/B/C/D/E
or
CATEGORY
TUNING MODE
DISPLAY
CATEGORY
EDIT
STRAIGHT
l
PROGRAM
h
ENTER
INPUT MODE
MULTI CH
INPUT
NEXT
A-E/CAT.
Front panel
A-E/CAT.
TONE CONTROL
BASS/TREBLE
Remote control
To search a channel within all channels,
press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control)
repeatedly.
2
3
1
Carry out “Selecting the XM Satellite Radio
mode” on page 40.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select “CAT
SEARCH”.
PRESET/CH
l PRESET/TUNING/CH h
or
LEVEL
ENTER
A-E/CAT.
A-E/CAT.
SET MENU
PRESET/TUNING
Front panel
or
SEARCH MODE
Remote control
MENU
SRCH MODE
EDIT
y
Front panel
You can search a channel with the quick search by pressing and
holding PRESET/TUNING/CH l / h (or PRESET/CH u / d
on the remote control).
VCR
V-AUX
Remote control
DTV/C BL
SP
A
DVD
MD/CD-R
TUNER
TUNED
CD
XM
CAT SEARCH
3
To change the channel category, press
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
PRESET/CH
A/B/C/D/E
or
CATEGORY
ENTER
NEXT
A-E/CAT.
Front panel
A-E/CAT.
Remote control
To search a channel within the selected
channel category, press PRESET/TUNING/CH
l / h (or PRESET/CH u / d on the remote
control) repeatedly.
PRESET/CH
l PRESET/TUNING/CH h
or
LEVEL
Front panel
ENTER
A-E/CAT.
A-E/CAT.
Remote control
y
You can search a channel with the quick search by pressing and
holding PRESET/TUNING/CH l / h (or PRESET/CH u / d
on the remote control).
42
XM SATELLITE RADIO TUNING
■ Preset Search mode
■ Direct Number Access mode
Prior to selecting a preset channel in the Preset Search
mode, you should preset XM Satellite Radio channels. For
details, see “Setting XM Satellite Radio preset channels”
on page 44. All preset channels (A1 to E8) recalls “001
Preview” by the factory setting.
MUTE
INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD S UR.
DIRECT ST .
5
6
7
8
NIGHT
STRAIGHT
MUTE
3
A SPEAKERS B
9
0
10
MOVIE
4
2
ENT.
LEVEL
SET MENU
TITLE
MENU
B AND
SRCH MODE
ENTER
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
A-E/C AT.
TUNING MODE
RETURN
DISPLAY
CATEGORY
NEXT
EDIT
A-E/C AT.
MEMORY
AUTO/MAN'L MONO
DISPLAY
PRESET/CH
INPUT
STRAIGHT
l
PROGRAM
h
INPUT MODE
TONE CONTROL
MULTI CH
INPUT
BASS/TREBLE
2
Carry out “Selecting the XM Satellite Radio
mode” on page 40.
1
Carry out “Selecting the XM Satellite Radio
mode” on page 40.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select “ALL
CH SEARCH” or “CAT SEARCH”.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select
“PRESET SEARCH”.
PRESET/TUNING
or
MENU
SRCH MODE
EDIT
Front panel
SET MENU
or
SEARCH MODE
SET MENU
PRESET/TUNING
SEARCH MODE
Remote control
MENU
EDIT
SRCH MODE
Front panel
Remote control
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
SP
A
CD
SP
A
XM
PRESET SEARCH
3
XM
ALL CH SEARCH
TUNED
or
VCR
To change the preset group (A to E), press
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
V-AUX
SP
A
DTV/C BL
DVD
MD/CD-R
TUNER
TUNED
CD
XM
CAT SEARCH
PRESET/CH
A/B/C/D/E
or
CATEGORY
ENTER
NEXT
A-E/CAT.
Front panel
A-E/CAT.
Remote control
To change the preset number (1 to 8), press
PRESET/TUNING/CH l / h (or PRESET/CH
u / d on the remote control) repeatedly.
PRESET/CH
l PRESET/TUNING/CH h
or
ENTER
LEVEL
A-E/CAT.
Front panel
A-E/CAT.
Remote control
y
You can also select the preset number directly by pressing the
numeric buttons (1 to 8) on the remote control.
43
BASIC
OPERATION
1
3
XM SATELLITE RADIO TUNING
3
Press the numeric buttons to enter the
desired channel number.
For example, to enter the number 123, press the
numeric buttons as shown below.
STEREO
MUSIC
ENTERTAIN
1
2
3
Setting XM Satellite Radio preset
channels
You can use this feature to store up to 40 XM Satellite
Radio channels (eight preset numbers in five preset
groups, A1 to E8). You can then recall any preset channel
easily by selecting the preset group and number as
described in “Preset Search mode” on page 43.
The display changes as follows.
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
PRESET/TUNING
SP
A
XM
<XM> --1
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
STRAIGHT
l
h
PROGRAM
INPUT MODE
TONE CONTROL
VCR
V-AUX
DTV/CBL
DVD
SP
A
MD/CD-R
TUNER
CD
XM
<XM> -12
V-AUX
DTV/CBL
SP
A
DVD
MD/CD-R
TUNER
CD
XM
<XM>123
4
4
3
1
VCR
MULTI CH
INPUT
BASS/TREBLE
If you enter fewer than three numbers, you
may press ENT. to tune to the channel
immediately or wait a few seconds to confirm
the entered channel number.
2,5
Search the XM Satellite Radio channel you
want to set as a preset channel.
To search the desired channel, carry out “All Channel
Search mode” on page 41, “Category Search mode”
on page 42, or “Direct Number Access mode” on
page 43.
VCR
V-AUX
DTV/CBL
SP
A
DVD
MD/CD-R
TUNER
CD
XM
[040] Deep Tra
When the channel number “040” is selected
ENT.
2
y
• If no button is pressed within a few seconds after entering onedigit or two-digit number, the unit automatically confirms the
entered channel number.
• Pressing a button other than numeric buttons or ENT. cancels
the direct number access procedure.
Press MEMORY on the unit (or remote
control during the TUNER mode).
The MEMORY indicator flashes for about five
seconds.
MEMORY
or
Front panel
Remote control
MEMORY
Flashes
44
RETURN
MEMORY
MAN'L/AUTO FM
XM SATELLITE RADIO TUNING
3
While the MEMORY indicator is flashing,
press CATEGORY (or A-E/CAT. j / i on the
remote control) to select a preset group
(A to E).
The group letter appears.
PRESET/CH
5
While the MEMORY indicator is flashing,
press MEMORY on the unit (or the remote
control) to preset the selected XM Satellite
Radio channel.
A colon appears next to the preset number for
confirmation, and the MEMORY indicator turns off.
A/B/C/D/E
MEMORY
or
CATEGORY
ENTER
NEXT
RETURN
or
A-E/CAT.
A-E/CAT.
MEMORY
MAN'L/AUTO FM
Remote control
Front panel
Remote control
Front panel
VCR
V-AUX
DTV/CBL
MD/CD-R
DVD
TUNER
CD
MEMORY
VCR
SP
A
C
DTV/CBL
DVD
MD/CD-R
TUNER
CD
MEMORY
[040] Deep
SP
A
XM
C5:[040] Deep
Preset group
Colon appears
While the MEMORY indicator is flashing,
press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control) to
select a preset number (1 to 8).
Note
Presetting a new channel clears the former preset channel stored
in the same preset group and number.
PRESET/CH
l PRESET/TUNING/CH h
or
ENTER
LEVEL
A-E/CAT.
Front panel
VCR
V-AUX
A-E/CAT.
Remote control
DTV/CBL
DVD
MD/CD-R
TUNER
CD
MEMORY
SP
A
XM
C5 [040] Deep
Preset number
45
BASIC
OPERATION
4
V-AUX
XM
XM SATELLITE RADIO TUNING
■
Status and error messages
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
Message
Cause
Remedy
CHECK ANTENNA
The XM Connect and Play digital antenna is not
connected, or does not work properly.
• Check the XM Connect and Play digital antenna
connections.
UPDATING
The XM user encryption code is being updated.
• Wait until the encryption code is updated.
NO SIGNAL
The signal is too weak.
• Check the XM Connect and Play digital antenna
connections and orient it for the best reception.
LOADING
It takes longer than four seconds for audio or
text data to be decoded.
• Wait until the decoding process has finished.
OFF AIR
The XM Satellite Radio channel you selected is
not currently broadcasting any signal.
• Check the channel number again or select another
XM Satellite Radio channel.
<XM> - - -
The channel Station ID (SID) is no longer
available.
- - -
No artist name/feature or song/program title is
available.
/
- - -
<CAT> - - -
46
No channels are available for the selected
category.
• Select another channel category by pressing
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
RECORDING
RECORDING
Recording adjustments and other operations are
performed from the recording components. Refer to the
operating instructions for those components.
(U.S.A. model)
VOLUME
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
FM/AM
XM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
CATEGORY
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
1
L
AUDIO
R
2
SYSTEM
POWER
STANDBY
POWER
AV
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
1
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
MULTI CH IN
REC
AUDIO
DISC SKIP
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of TONE CONTROL, VOLUME, “SP LEVEL”
(page 55) and the sound field programs does not affect recorded
material.
• A source connected to the MULTI CH INPUT jacks of this unit
cannot be recorded.
• Digital signals input to the DIGITAL INPUT jacks are not
output to the analog AUDIO OUT (L/R) jacks for recording.
You can only record analog signals.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR IN is not
output on VCR OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material may
infringe copyright laws.
CODE SET
AMP
TV
■ Special considerations when recording
DTS software
1
Turn on the power of this unit and all
connected components.
2
Select the source component you want to
record from.
INPUT
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
or
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For DVDs and CDs encoded with DTS, when your player
is compatible with the DTS format, follow its operating
instructions to make a setting so that the analog signal will
be output from the player.
MULTI CH IN
REC
AUDIO
DISC SKIP
Front panel
CODE SET
Remote control
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
y
Do a test recording before you start an actual recording.
47
BASIC
OPERATION
2
POWER
TV
CD
Notes
SOUND FIELD PROGRAM DESCRIPTIONS
SOUND FIELD PROGRAM DESCRIPTIONS
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
almost any sound source (stereo or multi-channel). This unit is also equipped with a YAMAHA digital sound field
processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.
Most of these sound field programs are precise digital recreations of actual acoustic environments found in famous
concert halls, music venues, and movie theaters.
y
The YAMAHA CINEMA DSP modes are compatible with all Dolby Digital, DTS, and Dolby Surround sources. Set the input mode to
AUTO (see page 30) to enable this unit to automatically switch to the appropriate digital decoder according to the input signal.
Notes
• This unit’s DSP sound field programs are recreations of real-world acoustic environments made from precise measurements taken in
the actual hall, etc. Thus you may notice variations in the strength of the reflections coming from the front, back, left and right.
• Feel free to choose a sound field program based on your listening preference, and not purely on the name of the program itself.
For movie/video sources
You can select from the following sound fields when playing movie or video sources. The sound fields marked “MULTI”
can be used with multi-channel sources, like DVD, digital TV, etc. Those marked “2-CH” can be used with 2-channel
(stereo) sources like TV programs, video tapes, etc.
Program selection methods vary depending on sound field program types. For details on how to
select sound field programs, see “Selecting sound field programs” on pages 26 to 30.
Remote
control
button
Features
1
STEREO:
2ch Stereo
Downmixes multi-channel sources to 2 channels (left and right) or plays back 2channel sources as is.
2
MUSIC:
Pop/Rock
This program lends an enthusiastic atmosphere to the sound, giving you the
feeling you are at an actual jazz or rock concert.
ENTERTAINMENT:
TV Sports
Though the presence sound field is relatively narrow, the surround sound field
employs the sound environment of a large concert hall. This effect enhances the
experience of watching various TV programs such as news, variety shows,
music programs or sports programs.
ENTERTAINMENT:
Mono Movie
This program is provided for reproducing monaural video sources (such as old
movies). The program produces the optimum reverberation to create sound
depth using only the presernce sound field.
ENTERTAINMENT:
Game
This program adds a deep and spatial feeling to video game sounds.
MOVIE THEATER:
Spectacle
CINEMA DSP processing. This program creates the extremely wide sound field
of a 70-mm movie theater. It precisely reproduces the source sound in detail,
making both the video and the sound field incredibly real. This is ideal for any
kind of video source encoded with Dolby Surround, Dolby Digital or DTS
(especially large-scale movie productions).
MOVIE THEATER:
Sci-Fi
CINEMA DSP processing. This program clearly reproduces dialog and sound
effects in the latest sound form for science fiction films, thus creating a broad
and expansive cinematic space amid silence. You can enjoy science fiction films
in a virtual-space sound field that includes Dolby Surround, Dolby Digital and
DTS-encoded software employing the most advanced techniques.
MOVIE THEATER:
Adventure
CINEMA DSP processing. This program is ideal for precisely reproducing the
sound design of the newest 70-mm and multi-channel soundtrack films. The
sound field is made to be similar to that of the newest movie theaters, so the
reverberations of the sound field itself are restrained as much as possible.
3
4
48
Program
Sources
MULTI
2-CH
SOUND FIELD PROGRAM DESCRIPTIONS
Remote
control
button
4
5
Program
Features
Sources
MOVIE THEATER:
General
CINEMA DSP processing. This program is for reproducing sounds from 70-mm
and multi-channel soundtrack films, and is characterized by soft and extensive
sound field.
MULTI
2-CH
SUR. STANDARD
Standard processing for the selected decoder.
SUR. ENHANCED
Enhanced processing for the selected decoder.
MULTI
2-CH
SOUND FIELD
PROGRAMS
49
SOUND FIELD PROGRAM DESCRIPTIONS
For music sources
You can select from the following sound fields when playing music sources, like CD, FM/AM broadcasting, tapes, etc.
Program selection methods vary depending on sound field program types. For details on how to
select sound field programs, see “Selecting sound field programs” on pages 26 to 30.
Remote
control
button
Program
Features
STEREO:
2ch Stereo
2-channel (left and right) playback.
STEREO:
5ch Stereo
Use to increase the output stereo sources (in stereo) from all speakers. This
provides a larger sound field and is ideal for background music at parties, etc.
MUSIC:
Hall in Vienna
HiFi DSP processing. A classic shoe-box type concert hall with approximately
1700 seats. Pillars and ornate carvings create extremely complex reflections
which produce a very full, rich sound.
MUSIC:
The Bttm Line
HiFi DSP processing. This is the sound field at stage front in “The Bottom
Line”, a famous New York jazz club. The floor can seat 300 people to the left
and right in a sound field offering a real and vibrant sound.
MUSIC:
The Roxy Thtr
HiFi DSP processing. The ideal program for lively, dynamic rock music. The
data for this program was recorded at LA’s “hottest” rock club. The listener’s
virtual seat is at the center-left of the hall.
ENTERTAINMENT:
Disco
HiFi DSP processing. This program recreates the acoustic environment of a
lively disco in the heart of a big city. The sound is dense and highly
concentrated. It is also characterized by high-energy, “immediate” sound.
SUR. STANDARD
Standard processing for the selected decoder.
SUR. ENHANCED
Enhanced processing for the selected decoder.
2-CH
1
2
3
5
50
Sources
MULTI
2-CH
MULTI
2-CH
ADVANCED OPERATIONS
ADVANCED OPERATIONS
■ Canceling the sleep timer
Using the sleep timer
Use this feature to automatically set this unit in the
standby mode after a certain amount of time. The sleep
timer is useful when you are going to sleep while this unit
is playing or recording a source. The sleep timer also
automatically turns off any external components
connected to AC OUTLET(S).
■ Setting the sleep timer
POWER
TV
AV
STANDBY
CD
MD/CD-R
TUNER
SLEEP
DTV/CBL
VCR
V-AUX
SLEEP OFF
The sleep timer setting can also be canceled by pressing
STANDBY on the remote control (or STANDBY/ON on the front
panel) to set this unit to the standby mode.
POWER
DVD
SLEEP
y
SYSTEM
POWER
Press SLEEP repeatedly until “SLEEP OFF” appears in
the front panel display.
After a few seconds, “SLEEP OFF” disappears, and the
SLEEP indicator goes off.
2
MULTI CH IN
REC
AUDIO
DISC SKIP
CODE SET
AMP
TV
1
Select a source and start playback on the
source component.
2
Press SLEEP repeatedly to set
the amount of time.
Each time you press SLEEP, the front
panel display changes as shown
below. The SLEEP indicator flashes
while switching the amount of time
for the sleep timer.
SLEEP 120min
SLEEP 90min
SLEEP 30min
VCR
V-AUX
DTV/CBL
DVD
SLEEP 60min
MD/CD-R
TUNER
CD
TUNED
SP
A
HiFi DSP
ADVANCED
OPERATION
SLEEP OFF
SLEEP
VOLUME
SLEEP
dB
L
R
The SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound
field program.
SLEEP indicator
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
SP
A
HiFi DSP
TV Sports
VOLUME
SLEEP
dB
L
R
51
ADVANCED OPERATIONS
Manually adjusting speaker levels
You can adjust the output level of each speaker while
listening to a music source. This is also possible when
playing sources through the MULTI CH INPUT jacks.
Please note that this operation will override the level
adjustments made in “BASIC SETUP” (page 21) and “SP
LEVEL” (page 55).
AMP
TV
VOL
MUTE
INPUT
STEREO
MUSIC
1
VOLUME
CH
MUTE
MOVIE
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
2
ENTERTAIN
1
0
10
ENT.
SET MENU
LEVEL
TITLE
MENU
BAND
SRCH MODE
ENTER
A-E/CAT.
A-E/CAT.
RETURN
MEMORY
DISPLAY
PRESET/CH
4
3
1
Press AMP.
2
Press LEVEL repeatedly to select the
speaker you want to adjust.
FRONT L
CENTER
FRONT R
SUR. R
SUR. L
SWFR
Front left speaker level
Center speaker level
Front right speaker level
Surround right speaker level
Surround left speaker level
Subwoofer level
y
Once you press LEVEL, you can also select the speaker by
pressing u / d.
3
Press j / i to adjust the speaker output level.
The control range is from +10 dB to –10 dB.
4
Press ENTER when you have completed your
adjustment.
y
This operation can also be performed using the controls on the
front panel. Press NEXT repeatedly to select the speaker you
want to adjust, then press LEVEL –/+ to adjust the output level.
52
SET MENU
SET MENU
You can use the following parameters in SET MENU to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ BASIC SETUP
Use to quickly setup basic system parameters (see page 21).
■ MANUAL SETUP
Use to adjust speaker and system settings manually.
1 SOUND MENU
Use to manually adjust any speaker setting, alter the quality and tone of the sound output by the system or compensate for
video signal processing delays when using LCD monitors or projectors.
y
Most of the parameters described in SOUND MENU are set automatically when you perform “BASIC SETUP” (see page 21). You can
use SOUND MENU to make further adjustments.
Item
Features
Page
A)SPEAKER SET
Selects the size of each speaker, the speakers for low-frequency signal output, and the cross over
frequency.
55
B)SP LEVEL
Adjusts the output level of each speaker.
55
C)SP DISTANCE
Adjusts the delay time of each speaker.
56
D)CENTER GEQ
Adjusts the tonal quality of the center speaker.
56
E)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
56
F)D.RANGE
Adjusts the dynamic range for Dolby Digital or DTS signals.
56
G)AUDIO SET
Customizes the muting level and audio delay.
57
2 INPUT MENU
Use to reassign digital input/outputs and select the input mode.
Item
Features
Page
Assigns jacks according to the component to be used.
57
B)INPUT MODE
Selects the initial input mode of the source.
58
C)INPUT RENAME
Changes the name of the inputs.
58
ADVANCED
OPERATION
A)I/O ASSIGN
3 OPTION MENU
Use to adjust the optional system parameters.
Item
Features
Page
A)DISPLAY SET
Adjusts the brightness of the display.
58
B)MEMORY GUARD
Locks sound field program parameters and other SET MENU settings.
58
C)PARAM. INI
Initializes the parameters of a group of sound field programs.
58
D)MULTI ZONE
Specifies the location of the speakers connected to the SPEAKERS B terminals.
59
E)XM RADIO SET
Displays the current reception level for the XM Connect and Play digital antenna.
59
53
SET MENU
Using SET MENU
6
Press ENTER to enter the displayed menu.
Repeat steps 5 and 6 to navigate to and enter the
items you want to adjust.
To return to the previous menu level, press RETURN.
7
Press u / d to select the item you want to
adjust, then press j / i to change the setting
of the item.
Repeat this operation to select and adjust each setting.
To return to the previous menu level, press RETURN.
8
To exit, press SET MENU when finished.
Use the remote control to access and adjust each
parameter.
AMP
TV
VOL
CH
MUTE
INPUT
1
VOLUME
MUTE
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
0
10
ENT.
SET MENU
LEVEL
TITLE
MENU
BAND
SRCH MODE
2,8
ENTER
A-E/CAT.
A-E/CAT.
RETURN
MEMORY
DISPLAY
PRESET/CH
3-7
y
You can change SET MENU parameters while the unit is
reproducing sound.
Note
You cannot change some SET MENU parameters while the unit
is in either cinema or music night listening mode.
1
Press AMP.
2
Press SET MENU.
“BASIC SETUP” appears in the front panel display.
3
Press u / d to display MANUAL SETUP.
MANUAL SETUP
4
Press ENTER to enter MANUAL SETUP.
1 SOUND MENU appears in the front panel display.
1 SOUND MENU
5
Press u / d to display the desired menu.
1 SOUND MENU
2 INPUT MENU
3 OPTION MENU
54
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, if the power cord is disconnected from the
AC outlet, or the power supply is cut for more than one
week, the stored data will be lost. If so, adjust the
items again.
SET MENU
1 SOUND MENU
Use to manually adjust any speaker setting or compensate
for video signal processing delays when using LCD
monitors or projectors. Most of the SOUND MENU
parameters are set automatically when you perform
“BASIC SETUP” (see page 21).
■ Speaker settings A)SPEAKER SET
Use to manually adjust any speaker setting.
y
If you are not satisfied with the bass sounds from your speakers,
you can change these settings according to your preference.
Front speakers FRONT
Choices: LARGE, SMALL
• Select LARGE if you have large front speakers. The
unit directs the entire range of the front left and right
channel signals to the front left and right speakers.
• Select SMALL if you have small front speakers. The
unit directs the low-frequency signals of the front
channel to the speakers selected with “BASS OUT”.
Center speaker CENTER
Choices: LRG, SML, NONE
• Select LRG if you have a large center speaker. The unit
directs the entire range of the center channel signal to
the center speaker.
• Select SML if you have a small center speaker. The
unit directs the low-frequency signals of the center
channel to the speakers selected with “BASS OUT”.
• Select NONE if you do not have a center speaker. The
unit directs all of the center channel signal to the front
left and right speakers.
Cross over CrossOver
Use this feature to select a cross-over (cut-off) frequency
for all low-frequency signals. All frequencies below the
selected frequency will be sent to the subwoofer.
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
Subwoofer phase SWFR PHASE
If bass sounds are lacking or unclear, use this feature to
switch the phase of your subwoofer.
Choices: NRM (normal), REV (reverse)
• Select NRM if you do not want to reverse the phase of
your subwoofer.
• Select REV to reverse the phase of your subwoofer.
■ Speaker level B)SP LEVEL
Use these settings to manually balance the level of each
speaker selected in SPEAKER SET (page 55).
Choices: –10.0 dB to +10.0 dB
• FL adjusts the balance of the front left speaker.
• FR adjusts the balance of the front right speaker.
• C adjusts the balance of the center speaker.
• SL adjusts the balance of the surround left speaker.
• SR adjusts the balance of the surround right speaker.
• SWFR adjusts the balance of the subwoofer.
55
ADVANCED
OPERATION
Surround left/right speakers SUR. LR
Choices: LRG, SML, NONE
• Select LRG if you have large surround left and right
speakers. The entire range of the surround channel
signal is directed to the surround left and right
speakers.
• Select SML if you have small surround left and right
speakers. The low-frequency signals of the surround
channel are directed to the speakers selected with
“BASS OUT”.
• Select NONE if you do not have surround speakers.
This will set the unit to the Virtual CINEMA DSP
mode (see page 30).
Bass out BASS OUT
Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right speakers
according to the characteristics of your system. This
setting also determines the routing of the LFE (lowfrequency effect) signals found in Dolby Digital or DTS
sources.
Choices: SWFR (subwoofer), FRONT, BOTH
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer according to the speaker settings.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front speakers according to the speaker settings
(even if you have previously set the front speakers to
SML).
• Select BOTH if you connect a subwoofer and you want
to output low-frequency signals from front channels to
both the front speakers and subwoofer. LFE and lowfrequency signals from other channels are also directed
to the subwoofer according to the speaker settings. Use
this function to reinforce low-frequency signals using
the subwoofer when playing back sources such as CDs.
SET MENU
■ Speaker distance C)SP DISTANCE
Use this feature to manually input the distance of each
speaker and adjust the delay applied to respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sound will arrive at the listening position at the same time.
■ Low-frequency effect level E)LFE LEVEL
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
U.S.A. and Canada models: feet (ft)
Other models: meters (m)
• Select meters to input speaker distances in meters.
• Select feet to input speaker distances in feet.
Speaker SP LFE
Select to adjust the speaker LFE level.
Speaker distances
Choices: 0.3 to 24.0 m (1 to 80 ft)
• FRONT L adjusts the distance of the front left speaker.
Initial setting: 3.0 m (10.0 ft)
• FRONT R adjusts the distance of the front right
speaker. Initial setting: 3.0 m (10.0 ft)
• CENTER adjusts the distance of the center speaker.
Initial setting: 3.0 m (10.0 ft)
• SUR.L adjusts the distance of the surround left
speaker. Initial setting: 3.0 m (10.0 ft)
• SUR.R adjusts the distance of the surround right
speaker. Initial setting: 3.0 m (10.0 ft)
• SWFR adjusts the distance of the subwoofer. Initial
setting: 3.0 m (10.0 ft)
■ Center graphic equalizer D)CENTER GEQ
Use this feature to adjust the built-in 5-band graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments listening to the currently selected
source component or a test tone.
You can adjust 5 frequency bands:
100Hz, 300Hz, 1kHz, 3kHz, 10kHz
Choices: –6 to +6 dB
Initial setting: 0 dB
• Select ON to output test tones from the front left and
center speakers, and adjust the tonal quality of the
center speaker.
• Select OFF to stop the test tone and output the
currently selected source component.
56
Use to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer or headphones. The LFE channel carries lowfrequency special effects which are only added to certain
scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Choices: –20 to 0 dB
Headphone HP LFE
Select to adjust the headphone LFE level.
Note
Depending on the “LFE LEVEL” setting, some signals may not
be output from the SUB WOOFER OUTPUT jack.
■ Dynamic range F)D.RANGE
Use to select the amount of dynamic range compression to
be applied to your speakers or headphones. This setting is
effective only when the unit is decoding Dolby Digital and
DTS signals.
Choices: MIN (minimum), STD (standard), MAX
(maximum)
Speaker SP D.R
Select to adjust the speaker compression.
Headphone HP D.R
Select to adjust the headphone compression.
• Select MIN for listening to sources at low volume
levels.
• Select STD for general use.
• Select MAX for feature films.
SET MENU
■ Audio settings G)AUDIO SET
Use to customize this units overall audio settings.
Muting type MUTE TYP.
Use to adjust how much the mute function reduces the
output volume.
Choices: FULL, –20dB
• Select FULL to completely halt all output of sound.
• Select –20dB to reduce the current volume by 20 dB.
Audio delay A.DELAY
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 ms
Tone bypass TC.BYPASS
Use to select whether audio output bypasses tone control
circuitry when TREBLE and BASS (page 25) are set to
0 dB.
Choices: AUTO, OFF
• Select AUTO if you want signals to bypass tone
control circuitry to provide the purest signal possible.
• Select OFF if you do not want signals to bypass tone
control circuitry.
2 INPUT MENU
Use to reassign digital input/outputs and select the input
mode.
■ Input/output assignment
A)I/O ASSIGN
You can assign jacks according to the component to be
used if this unit’s initial settings do not correspond to your
needs. Change the following parameters to reassign the
respective jacks and effectively connect more
components.
Once the inputs have been reassigned, you can select the
corresponding component by using INPUT on the front
panel or the input selector buttons on the remote control.
For COMPONENT VIDEO jacks A (C.V[A]) and
B (C.V[B])
Choices: [A] DVD, DTV/CBL, V-AUX, VCR
[B] DVD, DTV/CBL, V-AUX, VCR
For DIGITAL INPUT jacks 1 (IN (1)) and
2 (IN (2))
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
VCR
(2) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
VCR
For COAXIAL INPUT jack 3 (IN (3))
Choices: CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
VCR
Notes
• You cannot select a specific item more than once for the same
type of jack.
• When you connect a component to both the COAXIAL and
OPTICAL jacks, priority is given to the input signals from the
COAXIAL jack.
ADVANCED
OPERATION
57
SET MENU
■ Input mode B)INPUT MODE
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn on
this unit (see page 30 for details about the input mode).
Choices: AUTO, LAST
• Select AUTO to allow this unit to automatically detect
the type of input signal and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that source.
Note
Even if LAST is selected, the last setting for the EXTD SUR.
button will not be recalled.
■ Input rename C)INPUT RENAME
Use this feature to change the name of the inputs in the
front panel display.
1
Press an input selector button to select the
input you want to change the name of.
2
Press AMP.
3
Press j / i to place the _ (underbar) under the
space or the character you want to edit.
4
Press u / d to select the character you want,
then use j / i to move to the next space.
• You can use up to 8 characters for each input.
• Press d to change the character in the following
order, or press u to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space,
symbols (#, *, –, +, etc.).
5
Repeat steps 1 through 4 to rename each
input.
6
To exit, press SET MENU when finished.
58
3 OPTION MENU
Use to adjust the optional system parameters.
■ Display settings A)DISPLAY SET
Dimmer DIMMER
Use to adjust the brightness of the front panel display.
Choices: –4 to 0
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: ON, OFF
Select ON to protect:
• DSP program parameters
• All SET MENU items
• All speaker levels
When MEMORY GUARD is set to ON, you cannot select
any other SET MENU items.
■ Parameter initialization C)PARAM. INI
Use this feature to initialize the parameters for each sound
field program within a sound field program group. When
you initialize a sound field program group, all of the
parameter values within that group revert to their initial
settings.
Press the corresponding numeric button for the sound field
program that you want to initialize.
Choices: STEREO, MUSIC, ENTERTAINMENT,
MOVIE, STANDARD
Notes
• You cannot automatically revert to the previous parameter
settings once you initialize a sound field program group.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any program groups when “MEMORY
GUARD” is set to ON.
SET MENU
■ Zone set D)MULTI ZONE
Use to specify the location of speakers connected to the
SPEAKERS B terminals.
Speaker B setting SP B
Use this feature to select the location of the front speakers
connected to the SPEAKERS B terminals.
Choices: FRONT, ZONE B
• Select FRONT to turn on/off SPEAKERS A and B
when the speakers connected to the SPEAKERS B
terminals are set in the main room.
• Select ZONE B if the speakers connected to the
SPEAKERS B terminals are set in another room. If
SPEAKERS A is turned OFF and SPEAKERS B is
turned ON, all the speakers including the subwoofer in
the main room are muted and the unit outputs sound
from SPEAKERS B only.
Notes
• If you connect headphones to the PHONES jack on the unit
when “SP B” is set to ZONE B, the sound is output from both
headphones and SPEAKERS B.
• If a DSP program is selected when “SP B” is set to ZONE B,
the unit automatically enters the Virtual CINEMA DSP mode.
■ XM Radio setting E)XM RADIO SET
XM Radio antenna XM ANT.
Use to check the current reception level for the XM
Connect and Play digital antenna connected to this unit.
For the best reception, orient the XM Connect and Play
digital antenna so that a value of XX% or more is
displayed here.
Range: NONE, 0 to 100%
Note
“NONE” is displayed if the XM Connect and Play digital antenna
is not connected to this unit. If this happens, check the antenna
connections (see page 38).
ADVANCED
OPERATION
59
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other A/V components made by YAMAHA and
other manufacturers. To control other components, you must set up remote control with the appropriate remote control
codes.
Control area
■ Controlling this unit
■ Controlling other components
The shaded areas below can be used to control this unit
when the AMP mode is selected. Press AMP to activate
the AMP mode.
The shaded areas below can be used to control other
components. Each button has a different function
depending on the selected components. Select the
component you want to control by pressing an input
selector button.
SYSTEM
POWER
POWER
TV
AV
STANDBY
POWER
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
MULTI CH IN
REC
AUDIO
DISC SKIP
Press AMP
to control
this unit.
CODE SET
AMP
TV
The buttons in the
dotted lines
(SYSTEM
POWER,
STANDBY,
SLEEP, MULTI CH
IN, VOLUME +/–
and MUTE)
function in any
mode.
The input selector buttons
switch the function of the
component control area
below.
SYSTEM
POWER
TV
CH
MUTE
INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
POWER
POWER
CD
TV
MD/CD-R
AV
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
MULTI CH IN
REC
AUDIO
REC
DISC SKIP
CODE SET
AUDIO
DISC SKIP
VOLUME
VOL
STANDBY
POWER
AV
POWER
AMP
TV
MUTE
A SPEAKERS B
9
0
10
ENT.
LEVEL
SET MENU
TITLE
MENU
BAND
SRCH MODE
ENTER
A-E/CAT.
A-E/CAT.
RETURN
MEMORY
DISPLAY
PRESET/CH
TV
MOVIE
VOL
VOLUME
CH
VOL
MUTE
Component control
area
You can control up to 7
different components by
setting appropriate remote
control codes
(see page 61).
CH
INPUT
MUTE
STEREO
MUTE
MUSIC
INPUT
ENTERTAIN
1
2
STANDARD
STEREO
SELECT
1
5
6
STANDARD
A SPEAKERS 5B
9
A SPEAKERS B
0
NIGHT
SET10
MENU
STRAIGHT
ENT.
MENU
LEVEL
SRCH MODE
BAND
ENTER
A-E/CAT.
A-E/CAT.
PRESET/CH
RETURN
MEMORY
SET MENU
MENU
RETURN
60
ENT.
TITLE
MEMORY
4
EXTD SUR.
DIRECT ST.
STRAIGHT
7
8
10
9
MOVIE
8
SELECT
NIGHT
6
TITLE
BAND
4
7
0
LEVEL
MOVIE
3
MUSIC ENTERTAIN
EXTD
DIRECT
2 SUR.
3 ST.
SRCH MODE
A-E/CAT.
ENTER
DISPLAY
A-E/CAT.
DISPLAY
PRESET/CH
REMOTE CONTROL FEATURES
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area. For a complete list of available remote
control codes, refer to “LIST OF REMOTE CONTROL
CODES” at the end of this manual.
While holding down CODE SET, press an
input selector button to select the
component you want to set up.
The following table shows the default component
(Library: component category) and the remote control
code for each area.
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
MULTI CH I N
REC
AUDIO
DISC SKIP
CODE SET
AMP
Remote Control Code Default Settings
Input area
Component
category
(Library)
Manufacturer
Default
YAMAHA
code
CD
CD
YAMAHA
199
MD/CD-R
CD-R
YAMAHA
499
TUNER*1
TUNER
YAMAHA
FIX
DVD
DVD
YAMAHA
699
DTV/CBL*2
–
–
–
V-AUX
–
–
–
VCR
–
–
–
Note
You must press and hold CODE SET throughout this
procedure.
2
With CODE SET depressed, use the numeric
buttons to enter the four-digit remote control
code for the component to be used.
Refer to “LIST OF REMOTE CONTROL CODES”
at the end of this manual.
MULTI CH IN
REC
*1
*2
AUDIO
You can control this unit and other Yamaha tuners only.
You can only set TV remote control codes for the DTV/CBL
button.
DISC SKIP
CODE SET
AMP
TV
Note
You may not be able to operate your YAMAHA component even
if a YAMAHA remote control code is initially set as listed above.
In this case, try to set other YAMAHA remote control code(s).
VOLUME
VOL
CH
MUTE
INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
MUTE
A SPEAKERS B
0
7
8
NIGHT
STRAIGHT
10
ENT.
Notes
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• You can only assign one remote control code to each input
selector button.
61
ADVANCED
OPERATION
9
MOVIE
REMOTE CONTROL FEATURES
Controlling other components
Once you set the appropriate remote control codes, you
can use this remote to control your other components.
Note that some buttons may not correctly operate the
selected component. Use the input selector buttons to
select the component you want to operate. The remote
control automatically switches to the appropriate control
mode for that component.
1
2
6
SYSTEM
POWER
POWER
STANDBY
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
VCR
V-AUX
INPUT
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
5
6
MUTE
A SPEAKERS B
9
7
8
9
MULTI CH IN
REC
AUDIO
3
DISC SKIP
CODE SET
AMP
0
MUTE
STEREO
DIRECT ST.
7
8
NIGHT
STRAIGHT
0
10
ENT.
LEVEL
SET MENU
TITLE
MENU
BAND
SRCH MODE
A
B
C
ENTER
A-E/CAT.
A-E/CAT.
RETURN
MEMORY
DISPLAY
PRESET/CH
D
TV
4
5
DVD player
1
2
3
6
7
8
9
0
A
B
C
D
*1
VOLUME
MUTE
VCR
Digital TV/
Cable TV
CD player
MD/CD recorder
Tuner
Power *1
Power *1
VCR power *3
Power *1
Power *1
Power *1
TV POWER
TV power *2
TV power *2
TV power
TV power *2
TV power *2
TV power *2
REC/
DISC SKIP
Disc skip (player)
Rec
VCR rec *3
Disc Skip
Rec (MD)
Play
Play
VCR play *3
Play
Play
w
Search backward
Search backward
VCR search
backward *3
Search backward
Search backward
f
Search forward
Search forward
VCR search forward *3 Search forward
AUDIO
Audio
e
Pause
Pause
VCR pause *3
b
Skip backward
a
Skip forward
Search forward
Pause
Pause
Skip backward
Skip backward
Skip forward
Skip forward
Stop
Stop
VCR stop *3
Stop
Stop
VOL +
TV volume up *2
TV volume up *2
TV volume up
TV volume up *2
TV volume up *2
TV volume up *2
VOL –
TV volume down *2
TV volume down *2
TV volume down
TV volume down *2
TV volume down *2
TV volume down *2
TV channel up *2
s
5
CH
INPUT
AV POWER
p
4
VOL
MUTE
CH +
TV channel up *2
TV channel up *2
TV channel up
TV channel up *2
TV channel up *2
CH –
TV channel down *2
TV channel down *2
TV channel down
TV channel down *2
TV channel down *2
TV channel down *2
MUTE
TV mute *2
TV mute *2
TV mute
TV mute *2
TV mute *2
TV mute *2
TITLE
Title
Band
PRESET/CH u Up
VCR channel up
Preset up (1-8)
PRESET/CH d Down
VCR channel down
Preset down (1-8)
j
Left
Preset down (A-E)
i
Right
Preset up (A-E)
ENTER
Play
RETURN
Return
INPUT
TV input *2
1-9, 0, +10
Numeric buttons
Numeric buttons
Numeric buttons
ENT.
Title/Index
Enter
Enter
MENU
Menu
DISPLAY
Display
Display
Display
Display
TV input *2
TV input
TV input *2
TV input *2
TV input *2
Numeric buttons
Numeric buttons
Preset stations (1-8)
Index
Index
This button functions only when the original remote control of the component has a POWER button.
These buttons can operate your TV without switching the input if the remote control code is set in DTV/CBL.
*3 These buttons can operate your VCR without switching the input to VCR if the remote control code is set in VCR.
*2
62
EDITING SOUND FIELD PARAMETERS
EDITING SOUND FIELD PARAMETERS
What is a sound field
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound “live”, these reflections
enable us to tell where the player is situated, and the size
and shape of the room in which we are sitting.
Changing parameter settings
You can enjoy good quality sound with the factory preset
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
■ Elements of a sound field
VOL
CH
MUTE
INPUT
POWER
POWER
TV
AV
MUTE
POWER
STANDBY
STEREO
In any environment, in addition to the direct sound coming
straight to our ears from the player’s instrument, there are
two distinct types of sound reflections that combine to
make up the sound field:
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms
– 100 ms after the direct sound), after reflecting from one
surface only – for example, from the ceiling or a wall.
Early reflections actually add clarity to the direct sound.
Reverberations
These are caused by reflections from more than one
surface – walls, ceiling, the back of the room – so
numerous that they merge together to form a continuous
sonic “afterglow”. They are non-directional, and lessen
the clarity of the direct sound.
Direct sound, early reflections and subsequent
reverberation taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of a
concert hall, a dance floor, or virtually any size room at
all. This ability to create sound fields at will is exactly
what YAMAHA has done with the digital sound field
processor.
VOLUME
SYSTEM
CD
MD/CD-R
TUNER
MUSIC
ENTERTAIN
2
3
4
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
SLEEP
A SPEAKERS B
DVD
DTV/CBL
9
V-AUX
VCR
10
TITLE
MENU
BAND
SRCH MODE
ENTER
CODE SET
A-E/CAT.
A-E/CAT.
RETURN
AMP
2
ENT.
SET MENU
AUDIO
DISC SKIP
1
0
LEVEL
MULTI CH IN
REC
MOVIE
1
STANDARD
3,4
DISPLAY
MEMORY
PRESET/CH
TV
1
Press AMP.
2
Select the sound field program you want to
adjust.
AMP
STEREO
MUSIC
ENTERTAIN
2
3
4
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
3
MOVIE
1
STANDARD
0
10
ENT.
Press u / d to select
the parameters.
ENTER
A-E/CAT.
A-E/CAT.
PRESET/CH
4
Press j / i to change
the parameter value.
ENTER
A-E/CAT.
A-E/CAT.
ADDITIONAL
INFORMATION
PRESET/CH
y
If you press and hold j / i to change the parameter value, the
front panel display automatically stops at the factory preset
parameter moentarily.
63
EDITING SOUND FIELD PARAMETERS
5
Repeat steps 2 through 4 as necessary to
change other program parameters.
Note
You cannot change parameter values when “MEMORY
GUARD” is set to ON. If you want to change the parameter
values, set “MEMORY GUARD” to OFF (see page 58).
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter values will return to the
factory settings. If this happens, edit the parameter
value again.
■ Resetting all parameters to the factory
presets
Use PARAM. INI (see page 58).
64
SOUND FIELD PARAMETER DESCRIPTIONS
SOUND FIELD PARAMETER DESCRIPTIONS
You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your
listening room. Not all of the following parameters are found in every program.
■ DSP LEVEL (DSP level)
Function:
Description:
Control range:
Adjusts the level of all the DSP effect sounds within a narrow range.
Depending on the acoustics of your listening room, you may want to increase or decrease the DSP
effect level relative to the level of the direct sound.
–6 dB to +3 dB
■ INIT. DLY (Initial delay)
Function:
Description:
Control range:
Changes the apparent distance from the source sound by adjusting the delay between the direct sound
and the first reflection heard by the listener.
The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther
it seems. For a small room, set to a small value. For a large room, set to a large value.
1 to 99 msec
Source Sound
Time
Time
Time
Delay
Level
Level
Level
Early
Reflections
Delay
Delay
Sound Source
Reflection Face
Small value = 1 ms
Large value = 99 ms
For 2ch Stereo:
■ DIRECT (Direct)
Function:
Choices:
Bypasses this unit’s decoders and DSP processors for pure high fidelity sound when playing 2-channel
analog sources. The AUTO setting is effective only when BASS and TREBLE are set to 0 dB.
AUTO, OFF
Notes
65
ADDITIONAL
INFORMATION
• When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2 channels and output from the front left and
right speakers.
• When “BASS OUT” is set to BOTH, or “FRONT SP” set to SML and “BASS OUT” set to SWFR, front left and right speaker lowfrequency signals are redirected to the subwoofer.
SOUND FIELD PARAMETER DESCRIPTIONS
For 5ch Stereo:
Function:
Control range:
These parameters adjust the volume level for each channel in 5-channel stereo mode.
0 to 100%
■ CT LEVEL (Center level)
■ SL LEVEL (Surround left level)
■ SR LEVEL (Surround right level)
For PRO LOGIC II Music:
■ PANORAMA (Panorama)
Function:
Choices:
Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect.
OFF, ON
■ DIMENSION (Dimension)
Function:
Control range:
Gradually adjusts the sound field either towards the front or towards the rear.
–3 (towards the rear) to +3 (towards the front), initial setting is STD (standard).
■ CT WIDTH (Center width)
Function:
Control range:
Initial setting:
Adjusts the center image from all three front speakers to varying degrees. A larger value adjusts the
center image towards the front left and right speakers.
0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only
from front left and right speakers)
3
Note
This parameter can be set only when SUR. STANDARD is selected.
For DTS Neo:6 Music:
■ C. IMAGE (Center image)
Function:
Control range:
Initial setting:
Adjusts the center image from all three front speakers to varying degrees.
0 to 1.0
0.3
Note
This parameter can be set only when SUR. STANDARD is selected.
66
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
■ General
Problem
Cause
Remedy
Refer to
page
This unit fails to turn
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters the standby
mode soon after the
power has been
turned on.
The power cord is not connected or the
plug is not completely inserted.
Connect the power cord firmly.
The protection circuitry has been
activated.
Make sure all speaker wire connections on this unit
and on all speakers are secure and that the wire for
each connection does not touch anything other than
its respective connection.
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit in the standby mode, disconnect the
power cord, plug it back in after 30 seconds, then use
it normally.
—
No sound
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-19
The input mode is set to DTS or
ANALOG.
Select AUTO.
30
No appropriate input source has been
selected.
Select an appropriate input source with INPUT,
MULTI CH INPUT or the input selector buttons.
24
Speaker connections are not secure.
Secure the connections.
12
The front speakers to be used have not
been selected properly.
Select the front speakers with SPEAKERS A and/or
B.
24
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or any operation button of this unit to
resume audio ouput, then adjust the volume.
25
The input mode is set to ANALOG while
playing a source encoded with a DTS
signal.
Set the input mode to AUTO or DTS.
30
Signals this unit cannot reproduce are
being received from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
—
11-13
ADDITIONAL
INFORMATION
67
TROUBLESHOOTING
Problem
The sound suddenly
goes off.
Cause
Remedy
Refer to
page
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE to cancel a mute.
25
Only the speaker on
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
12
Incorrect balance settings in SET MENU.
Adjust the SP LEVEL settings.
55
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound from the
effect speakers.
The sound field programs are turned off.
Press STRAIGHT (EFFECT) to turn them on.
30
You are using a source or program
combination that does not output sound
from all channels.
Try another sound field program.
The output level of the center speaker is
set to minimum.
Raise the level of the center speaker.
55
“CENTER” in SET MENU is set to
NONE.
Select the appropriate setting for the center speaker.
55
One of the HiFi DSP programs (except for
6ch Stereo) has been selected.
Try another sound field program.
The output level of the surround speakers
is set to minimum.
Raise the output level of the surround speakers.
55
“SUR. LR” in SET MENU is set to
NONE.
Select the appropriate setting for the surround left and
right speakers.
55
A monaural source is being played with
STRAIGHT.
Press STRAIGHT (EFFECT) to turn on the sound
fields.
—
No sound from the
surround back
speaker.
“SUR. LR” in SET MENU is set to
NONE.
If the surround left and right speakers are set to
NONE, the surround back speaker setting is
automatically set to NONE. Select the appropriate
setting for the surround speakers.
55
No sound from the
subwoofer.
“BASS OUT” in SET MENU is set to
FRONT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
55
“BASS OUT” in SET MENU is set to
SWFR or FRONT when a 2-channel
source is being played.
Select BOTH.
55
No sound from the
center speaker.
No sound from the
surround speakers.
The source does not contain low bass
signals.
68
26, 48
26, 48
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO or DTS.
30
A “humming” sound
can be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the OUT
(REC) jacks of this unit is turned off.
Turn on the power to the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to this
DIGITAL OUTPUT
jack.
The source component is not connected to
this unit’s DIGITAL INPUT jacks.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT jacks.
Connect the source component to the DIGITAL
INPUT jacks.
14-18, 47
The source component is not connected to
this unit’s analog AUDIO IN jacks.
Connect the source component to the analog AUDIO
IN jacks.
14-18, 47
The sound field
parameters and some
other settings on this
unit cannot be
changed.
“MEMORY GUARD” in SET MENU is
set to ON.
Select OFF.
58
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the AC power cord from the outlet and
then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short circuited.
Make sure all speaker cables are connected correctly.
12
There is noise
interference from
digital or radio
frequency equipment,
or this unit.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
turns into the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
Some components cannot record the
Dolby Digital or DTS sources.
ADDITIONAL
INFORMATION
69
TROUBLESHOOTING
■ Tuner
Problem
Cause
FM stereo reception is
noisy.
FM
AM
Remedy
Refer
to page
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Check the antenna connections.
Try using a high-quality directional FM
antenna.
19
Use the manual tuning method.
33
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multipath interference.
Adjust the antenna position to eliminate
multipath interference.
—
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is too weak.
Use a high-quality directional FM antenna.
19
Use the manual tuning method.
33
Previously preset
stations can no longer
be tuned in.
This unit has been disconnected for a
long period.
Preset the stations again.
33
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
—
Use the manual tuning method.
33
There are continuous
crackling and hissing
noises.
Noises result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV.
—
■ Remote control
Problem
The remote control
does not work nor
function properly.
Cause
Refer to
page
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
7
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The remote control code was not correctly
set.
Set the remote control code correctly using “LIST OF
REMOTE CONTROL CODES” at the end of this
manual.
61
Try to set another code for the same remote control
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
61
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
70
Remedy
RESETTING THE FACTORY PRESETS
RESETTING THE FACTORY PRESETS
If you want to reset all of your unit’s parameters for any
reason, do the following. This procedure completely resets
ALL parameters, including the SET MENU, level, assign
and tuner presets.
Be sure this unit is in standby mode.
2
Press STRAIGHT (EFFECT) to select the
desired setting.
STRAIGHT
EFFECT
RESET
CANCEL
VOLUME
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
FM/AM
XM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
CATEGORY
TUNING MODE
DISPLAY
NEXT
EDIT
AUTO/MAN'L MONO
3
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
STANDBY/ON
1
To reset the unit to its factory presets.
To cancel without making any changes.
L
AUDIO
R
STRAIGHT (EFFECT)
With the unit in standby mode, hold down
STRAIGHT (EFFECT) on the front panel and
press STANDBY/ON.
“PRESET –CANCEL” appears in the front panel
display.
Press STANDBY/ON to confirm your
selection.
STANDBY
/ON
If you selected “RESET”, the unit is reset to it’s
factory presets and switches to standby mode.
If you selected “CANCEL”, the unit switches to
standby mode and nothing is reset.
STRAIGHT
EFFECT
While holding
down, press
STANDBY
/ON
PRESET -CANCEL
y
To cancel the initialization procedure without making any
changes, press STANDBY/ON.
ADDITIONAL
INFORMATION
71
GLOSSARY
GLOSSARY
Audio formats
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround speakers, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround
software. This new technology enables a discrete 5channel playback with 2 front left and right channels, 1
center channel, and 2 surround left and right channels
(instead of only 1 surround channel for conventional Pro
Logic technology). Music and Game modes are also
available for 2-channel sources in addition to the Movie
mode.
■ Dolby Surround
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ DTS 96/24
DTS 96/24 offers an unprecedented level of audio quality
for multi-channel sound on DVD-Video, and is fully
backward-compatible with all DTS decoders. “96” refers
to a 96 kHz sampling rate (compared to the typical 48 kHz
sampling rate). “24” refers to 24-bit word length. DTS 96/
24 offers sound quality transparent to the original 96/24
master, and 96/24 5.1-channel sound with full-quality fullmotion video for music programs and motion picture
soundtracks on DVD-video.
■ DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can
enjoy the depth of sound and natural spatial representation
of DTS digital surround in your home. This system
produces practically distortion-free 6-channel sound
(technically, a left, right and center channels, 2 surround
channels, plus an LFE 0.1 channel as a subwoofer, for a
total of 5.1-channels). The unit incorporates a DTS-ES
decoder that enables 6.1- channel reproduction by adding
the surround back channel to existing 5.1-channel format.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6
channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available; “Music mode” for playing music
sources and “Cinema mode” for movies.
72
GLOSSARY
Sound field programs
Audio information
■ CINEMA DSP
■ ITU-R
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers and designed
for acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it’s inevitable that there are differences in
the sound heard as well. Based on a wealth of actually
measured data, YAMAHA CINEMA DSP uses
YAMAHA original sound field technology to combine
Dolby Pro Logic, Dolby Digital and DTS systems to
provide the visual and audio experience of movie theater
in the listening room of your own home.
ITU-R is the radio communication sector of the ITU
(International Telecommunication Union). ITU-R
recommends a standard speaker placement which is used
in many critical listening rooms, especially for mastering
purposes.
■ SILENT CINEMA
YAMAHA has developed a natural, realistic sound effect
DSP algorithm for headphones.
Parameters for headphones have been set for each sound
field so that accurate representations of all the sound field
programs can be enjoyed on headphones.
■ Virtual CINEMA DSP
YAMAHA has developed a Virtual CINEMA DSP
algorithm that allows you to enjoy DSP sound field
surround effects even without any surround speakers by
using virtual surround speakers.
It is even possible to enjoy Virtual CINEMA DSP using a
minimal two-speaker system that does not include a center
speaker.
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “pulse code
modulation”, the analog signal is encoded as pulses and
then modulated for recording.
■ Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits.
The range of rates that can be played back is determined
based on the sampling rate, while the dynamic range
representing the sound level difference is determined by
the number of quantized bits. In principle, the higher the
sampling frequency, the wider the range of frequencies
that can be played back, and the higher the number of
quantized bits, the more finely the sound level can be
reproduced.
ADDITIONAL
INFORMATION
73
GLOSSARY
Video signal information
■ Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal.
A monitor with component input jacks is required in order
to use the component signal for output.
■ Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture;
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
74
SPECIFICATIONS
SPECIFICATIONS
AUDIO SECTION
VIDEO SECTION
• Minimum RMS Output Power for Front, Center, Surround
1 kHz, 0.9% THD, 6 Ω ........................................................ 120 W
• Video Signal Type .......................................................... PAL/NTSC
• Minimum RMS Output Power for Subwoofer
30 Hz, 6 Ω ........................................................................... 120 W
• Dynamic Power (IHF)
6/4/2 Ω .................................................................. 150/185/230 W
• Damping Factor (IHF)
20 Hz to 20 kHz, 8 Ω................................................... 120 or more
• Frequency Response
CD terminal to Front L/R ...................... 10 Hz to 100 kHz, –3 dB
• Total Harmonic Distortion
CD, etc. to Front L/R
(20 Hz to 20 kHz, 40 W, 8 Ω)............................... 0.06% or less
• Signal to Noise Ratio (IHF-A Network)
CD (250 mV) to Front L/R, Effect Off .................. 100 dB or more
• Residual Noise (IHF-A Network)
Front L/R ............................................................... 150 µV or less
• Channel Separation (1 kHz/10 kHz)
CD (5.1 kΩ terminated) to Front L/R .......... 60 dB/45 dB or more
• Signal to Noise Ratio ................................................ 50 dB or more
• Frequency Response (MONITOR OUT)
Composite ................................................ 5 Hz to 10 MHz, –3 dB
Component ............................................... 5 Hz to 60 MHz, –3 dB
FM SECTION
• Tuning Range ..................................................... 87.5 to 107.9 MHz
• Usable Sensitivity (IHF)........................................ 1.0 µV (11.2 dBf)
• Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 76 dB/70 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................ 0.2%/0.3%
• Stereo Separation (1 kHz) ....................................................... 42 dB
• Frequency Response .......................... 20 Hz to 15 kHz, +0.5, –2 dB
AM SECTION
• Tuning Range ........................................................ 530 to 1710 kHz
• Usable Sensitivity ............................................................. 300 µV/m
• Tone Control (Front L/R)
BASS Boost/Cut ..................................................... ±10 dB/60 Hz
TREBLE Boost/Cut .............................................. ±10 dB/20 kHz
GENERAL
• Phones Output .......................................................... 150 mV/100 Ω
• Power Consumption ................................................. 350 W/440 VA
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Standby Power Consumption ...................................... 0.1 W or less
• Output Level/Output Impedance
REC OUT ............................................................. 200 mV/1.2 kΩ
SUBWOOFER.............................................................. 4 V/1.2 kΩ
• Power Supply ........................................................ AC 120 V, 60 Hz
• AC Outlets ............................................. 2 (Total 100 W maximum)
• Dimensions (W x H x D) ................................. 435 x 161 x 416 mm
(17-1/8” x 6-5/16” x 16-3/8”)
• Weight ................................................................ 11 kg (24 lbs 4 oz)
ADDITIONAL
INFORMATION
75
LIST OF REMOTE CONTROL CODES
TV
Yamaha
Admiral
Aiwa
Akai
Alba
AOC
Bell&Howell
Bestar
Blaupunkt
Blue sky
Brandt
Brocsonic
Bush
Clatronic
Craig
Croslex
Curtis Mathis
Daewoo
299, 292, 253, 242
292, 293
294, 276, 283, 284
295, 296
296
297
292
298
229, 222
298
223
297
296
298
224
225
297, 226
297, 298, 224,
227, 228
Daytron
239
Dual
298
Dwin
293
Emerson
297, 224, 239, 232
Ferguson
223, 265, 266
First line
298
Funai
277, 278
Fisher
295, 233
Fraba
298
GE
293, 297, 234,
235, 236
LG/Goldstar
297, 298, 239, 237
Goodmans
296, 298, 223
Grundig
229, 238, 249
Hitachi
297, 239, 242,
243, 285
ICE
296
Irradio
296
Itt/Nokia
244, 245
JC Penny
293, 297, 234, 237
JVC
296, 246, 247, 286
Kendo
298
KTV
297, 239
Loewe
298, 248
LXI
293, 297, 225,
226, 233
Magnavox
297, 225, 239
Marantz
298
Matsui
295
Memorex
297
Mitsubishi
299, 297, 259, 287
NEC
297, 252, 282
Nokia
244, 245
Nokia Oceanic 245
Nordmende
265, 266
Onwa
296
Panasonic
234, 235, 236,
253, 288, 211
Philco
297, 225, 239
Philips
225
Pioneer
Portland
Proscan
Proton
Quasar
Radio Shack
RCA
SABA
Sampo
Samsung
Sanyo
Schneider
Scott
Sharp
Siemens
Signature
Sony
Sylvania
Telefunken
Thomson
Toshiba
Videch
Wards
226, 235, 254,
255, 268
297, 256
293
297
234, 235
299, 293, 297
293, 297, 234,
256, 257, 258
223, 269, 265, 266
297
297, 239, 248,
262, 275
295, 233, 279,
272, 273, 274, 212
296
297
292, 239, 232,
213, 216
229
292
263, 214
297, 225
269, 264, 265, 266
223, 266
292, 226, 267, 215
297, 242
297, 239, 232
VCR
Yamaha
Admiral
Aiwa
Akai
Audio Dynamic
Bell&Howell
Blaupunkt
Brocsonic
Bush
Canon
CGM
Citizen
Craig
Curtis Mathis
Daewoo
DBX
Dimensia
Dynatech
Emerson
Fisher
Funai
GE
Go Video
LG/Goldstar
Goodmans
Grundig
Hitachi
399, 392, 393, 394
395
396, 397, 398, 329
322, 323, 324
392, 394
393
325, 326
327
322
325, 328
396, 332
396
396, 363
397, 328, 333
328, 334, 335
392, 394
333
397
327, 334, 396, 397
393, 336
397
328, 333, 387
353
396, 388
334, 337
332, 338
325, 333, 349,
342, 343
Instant Replay 325, 328
Itt/Nokia
393
JC Penny
392, 393, 394,
328, 333, 349,
396, 363
JVC
392, 394, 344,
345, 346, 347
Kendo
396
Kenwood
392, 394, 396
Loewe
396, 337
Luxor
395
LXI
393, 396, 397,
336, 349
Magnavox
325, 326, 328
Marantz
392, 394
Marta
396
Matsui
396
Memorex
328, 336, 396, 397
Minolta
333, 349
Mitsubishi
399, 344, 348,
359, 352, 353
MTC
363, 397
Multitech
397, 348, 354
NEC
392, 394, 344, 383
Nokia
393, 395
Nokia Oceanic 395
Okano
323
Olympic
325, 328
Orion
327
Panasonic
325, 328, 355,
378, 384, 385, 386
Pentax
333, 349
Philco
325, 328, 397
Philips
325, 326, 328,
337, 356, 357
Phonola
337
Pilot
396
Pioneer
325
Quasar
325, 328
RCA/PROSCAN
325, 326,
328, 333, 335,
349, 358, 369,
363, 397
Realistic
393, 397, 328,
336, 359, 362,
396, 363
Samsung
354, 358, 363,
364, 365, 366
Sansui
394
Sanyo
393, 336, 367
Schneider
337
Scott
399, 335, 336,
348, 359, 352,
354, 358
Seleco
322
Sharp
395, 362, 382
Siemens
393
Signature 2000 395, 397
Sony
368, 379, 372,
373, 374, 375
Sylvania
397, 325, 326, 328
Symphonic
397
Tandberg
334
Tandy
397
© 2005
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Tashiro
Tatung
Teac
Technics
Teknika
Telefunken
Thomas
Thorn
Toshiba
Totevison
Unitech
Universum
Videosonic
W.WHouse
Wards
Zenith
396
392, 394
392, 394, 397
325, 328
396
376, 377
397
393, 396
335, 369, 389
363, 396
363
396, 327, 376
363
396
395, 396, 336, 362
344, 368, 379,
396, 397
DVD player
Yamaha
699, 622, 623
DENON
623, 624
Funai
625
HITACHI
626
JVC
627
KENWOOD
628
Mitsubishi
629
Onkyo
632, 633, 634
Panasonic
623, 635
Philips
699, 647
Pioneer
636, 637, 638
RCA
639
Samsung
642
Sharp
643
Sony
644
Toshiba
634
LG/GOLD STAR
645
THOMSON
646
MD player
Yamaha
599
CD player
Yamaha
199
CD recorder
Yamaha
499
All rights reserved.
Printed in Malaysia
WE62340
© 2005
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Malaysia
WE62340