Sharp DV-NC150U Operating instructions

Precautions
VCR/DVD COMBINATION
Setup
OPERATION MANUAL
Please read this Operation Manual carefully before using
your VCR/DVD COMBINATION.
DVD Functions VCR Functions
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
Basic TV Connection
Cable
Signal
Cable
Signal
Antenna
or
(Back of TV)
Disconnect
Antenna (Back of
VCR/DVD)
or
2
(Back of TV)
ANT-IN
Connect
ANT-OUT
3
Connect
Round Coaxial cable (supplied)
5
Please refer to "Connections" on page 7.
Downloaded From DvDPlayer-Manual.com Sharp Manuals
4
AC
outlets Plug in
From
VCR/DVD
From
TV
Español
Information
The region number for this
VCR/DVD is 1.
1
For future reference, record the serial number (located on the rear of the
Unit) in the space provided.
Model No.:
DV-NC150U
Serial No.:
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Precautions
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITAR LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
CAUTION
This symbol warns the user of uninsulated
voltage within the unit that can cause dangerous electric shocks.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol alerts the user that there are
important operating and maintenance instructions in the literature accompanying this unit.
“WARNING—FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.”
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Este aparato digital de la Clase B cumple con la norma ICES-003 de Canadá.
NOTE to CATV system installer:
This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable entry as practical.
CAUTION:
THIS UNIT IS A CLASS 1 LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS UNIT IS HARMFUL TO THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Products that have earned ENERGY STAR® are designed to protect the environment through superior energy efficiency.
–2–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Important Safeguards
ANSI/NFPA No. 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
15. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the video product due to lightning and
power-line surges.
16. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might
be fatal.
17. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
19. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
20. Damage Requiring Service - Unplug this video product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any
way.
f. When the video product exhibits a distinct change in performance this indicates a need for service.
21. Replacement Parts - When replacement parts are
required, be sure the service technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
22. Safety Check - Upon completion of any service or repairs
to this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
23. Heat - This video product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
–3–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
ANTENNA
LEAD
WIRE
Precautions
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use
a
damp
cloth
for
cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the
possibility of the loss of an authorization code for a CATV
converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. Attachments - Do not use attachments not recommended
by the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories - Do not place this video product on an unstable cart, stand, tripod, bracket, or table. The video product
may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only
with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the video product. Any
mounting of the appliance should follow
the manufacturer's instructions and
should use a mounting accessory recommended by the manufacturer.
9. Transportation - A product and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the
video product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the video product on a
bed, sofa, rug, or other similar surface. This video product
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
11. Power Sources - This video product should be operated
only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
12. Grounding or Polarization - This video product is equipped
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
13. Power Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
14. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
EN
Table of Contents
Precautions
Precautions
■ Important Safeguards . . . . . . . . .
Symbol Used in This Manual . . . . .
Supplied Accessory . . . . . . . . . . . .
Service . . . . . . . . . . . . . . . . . . . . .
Copy Protection . . . . . . . . . . . . . . .
Recommended Measures for
Optimum Picture Excellence . . . . .
Notice for progressive scan outputs
No Fingers or Other Objects Inside
Warning of Dew Formation. . . . . . .
Others . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3
4
4
5
5
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
5
5
5
5
5
6
Setup
■ About the Video Cassettes and Discs . . . . . . . 7
Playable Video Cassettes. . . . . . . . . . . . . . . . . . . 7
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unplayable Discs . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . 7
Hint for Cable Box or Satellite Box . . . . . . . . . . . . 8
Connection to an Audio System . . . . . . . . . . . . . . 8
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . 9
Front & Rear Terminals . . . . . . . . . . . . . . . . . . . . 9
■ About the Remote Control and Front Panel . . 10
■ VCR/DVD Switching. . . . . . . . . . . . . . . . . . . . . 11
■ Preparation for Use . . . . . . . . . . . . . . . . . . . . . 12
Turn on the unit for the first time. . . . . . . . . . . . . 12
Clock Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VCR Functions
■
■
■
■
■
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording & OTR (One Touch Recording) .
Other Operations. . . . . . . . . . . . . . . . . . . . .
On-Screen Operations. . . . . . . . . . . . . . . . .
Recording Features . . . . . . . . . . . . . . . . . . .
Timer Recording . . . . . . . . . . . . . . . . . . . . . .
Hint for Timer Recording . . . . . . . . . . . . . . . .
Copying a Video Tape . . . . . . . . . . . . . . . . . .
■ MTS System (Multi-Channel Television Sound) .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
■ Special Features . . . . . . . . . . . . . . . . . . . . . . . 16
Time Search / Index Search / Auto Repeat. . . . . 16
DVD Functions
■
■
■
■
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . .
MP3 Playback . . . . . . . . . . . . . . . . . . . . . . .
The On-Screen Display . . . . . . . . . . . . . . . .
Search Function . . . . . . . . . . . . . . . . . . . . .
Track Search / Title/Chapter Search / Time Search
■ Marker Setup . . . . . . . . . . . . . . . . . . . . . . . .
■ Repeat / Random / Programmed Playback .
Repeat Playback / Repeat A-B Playback /
Random Playback / Programmed Playback . .
■ Special Settings. . . . . . . . . . . . . . . . . . . . . .
Subtitle Language / Audio Language /
Camera Angle / Stereo Sound Mode . . . . . . .
Black Level Setting / Virtual Surround. . . . . . .
■ DVD Set Up . . . . . . . . . . . . . . . . . . . . . . . . .
LANGUAGE Setting . . . . . . . . . . . . . . . . . . . .
DISPLAY Setting . . . . . . . . . . . . . . . . . . . . . .
AUDIO Setting . . . . . . . . . . . . . . . . . . . . . . . .
PARENTAL Setting. . . . . . . . . . . . . . . . . . . . .
To return the All Selections of SET UP
(except for PARENTAL) to the Default Setting.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
17
19
19
20
20
20
21
. . 21
. . 22
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
23
23
24
24
25
26
. . 26
Information
■ Language List . . . . . . .
■ Specifications . . . . . . .
Service Information . . . .
■ Troubleshooting Guide
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
27
28
28
29
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Importantes Medidas de Seguridad y
Precauciones. . . . . . . . . . . . . . . . . . . . . . . . .
Conexiones . . . . . . . . . . . . . . . . . . . . . . . . . .
Instalación de las pilas del mando a distancia
Conmutación VCR/DVD . . . . . . . . . . . . . . . . .
Activación de la unidad por primera vez . . . . .
Ajuste del reloj. . . . . . . . . . . . . . . . . . . . . . . .
Reproducción de la grabadora de vídeo . . . . .
Reproducción de DVD/CD . . . . . . . . . . . . . . .
Mando a distancia . . . . . . . . . . . . . . . . . . . . .
13
13
13
14
14
14
15
15
15
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
31
32
32
32
32
33
33
33
34
Symbol Used in This Manual
The following symbols appear in some headings and notes in this manual.
VCR
DVD-V
VR mode
: Description refers to playback or recording
of video cassette tapes.
: Description refers to playback of the VR
mode (Video Recording format).
*The VR mode (Video Recording format) is a recording mode to enjoy editing the program or “manual
mode” for recording in desired resolution and time.
DVD-V
: Description refers to playback of DVD-Video discs.
CD
: Description refers to playback of Audio CDs.
MP3
: Description refers to playback of MP3 files.
QUICK : Indicates DVD Setup menus also accessible
from the QUICK SETUP Menu. (Refer to
page 23.)
Supplied Accessory
• Remote control
(9HSNA276UD)
with two AA batteries
• Round Coaxial cable
(9HSWPZ0901TM003)
• Audio cable/ Video cable
(9HSWX1E56B5-001)
• Operation Manual
(9HS1VMN20342)
Operation Manual
–4–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Location and Handling
• Do not cover or place the VCR/DVD in enclosed spaces to prevent excessive temperature build up.
• Do not place the VCR/DVD in direct sunlight, or near heat sources.
• Depending on the use environment, the temperature of the VCR/DVD may increase slightly. This is not a malfunction.
• Keep the VCR/DVD away from strong magnetic objects.
• Do not place any object containing water or other liquids on the VCR/DVD. In the event that liquid should enter the cabinet, unplug the VCR/DVD immediately and contact the retailer or service centre approved by SHARP immediately.
• Do not remove the VCR/DVD cabinet. Touching parts inside the cabinet could result in electric shock and/ or damage to
the VCR/DVD. For service and adjustment inside the cabinet, call a qualified dealer or service centre approved by SHARP.
Nonuse Periods
Location and Handling
• When the VCR/DVD is not being used, switch the VCR/DVD to the Standby mode.
• When left unused for a long period of time, the VCR/DVD should be unplugged from the household AC outlet.
• Do not place the VCR/DVD in direct sunlight, or near heat sources.
Copy Protection
This Unit supports Macrovision copy protection.
On DVD discs that include a copy protection code, if the contents of the DVD disc are copied using a VCR, the
copy protection code prevents the videotape copy from playing normally.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093 licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Notice for progressive scan outputs
Consumers should note that not all high definition television sets are fully compatible with this product and may
cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding
our TV set compatibility with this model 525p DVD player, please contact our customer service center.
No Fingers or Other Objects Inside
Do not put your fingers or objects on the disc tray or in the cassette compartment.
Warning of Dew Formation
Moisture may form inside the VCR/DVD under the following conditions:
• Immediately after a heater is turned on.
• In a steamy or humid room.
• When the VCR/DVD is suddenly moved from a cold to warm environment.
If moisture forms inside this VCR/DVD, it may not operate properly or damage the video cassette. In such case,
turn on the power and wait for more than two hours for the moisture to evaporate.
Others
It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States
and that prior permission be obtained from copyright owners whenever necessary.
“Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678, 5,323,396, 5,530,655, 5,539,829, 5,544,247,
5,606,618, 5,610,985, 5,740,317, 5,777,992, 5,878,080, or 5,960,037.”
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
–5–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Precautions
Location and Handling
Maintenance
Precautions
SERVICING
1. Please refer to relevant topics in the Troubleshooting Guide on page 29 before returning the product.
2. Do not attempt to service this Unit yourself. Instead, unplug it and contact a Sharp Authorized Service Center for
inspection. (See Service Information on page 28.)
3. Be sure the service technician uses authorized replacement parts or their equivalents. Unauthorized parts may
cause fire, electrical shock, or other hazards.
4. Following any service or repair, be sure the service technician performs safety checks to certify that this Unit
is in safe operating order.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a
circular motion.
¡Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning
agents or antistatic spray intended for analogue records.
RECOMMENDED MEASURES FOR OPTIMUM PICTURE EXCELLENCE
This Unit is a precision device constructed using extremely accurate technology.
¡The disc cannot be played if the disc drive component is worn out or if the internal pick up lens is dirty.
¡If this unit still does not perform properly although you refer to the relevant sections and to Troubleshooting
Guide on page 29, the laser optical pickup unit may be dirty. Consult a Sharp Authorized Service Center for
inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
¡Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is not used.
AUTO HEAD CLEANING
¡Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
¡Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated
on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a
streaky or snowy picture appears during playback, the video heads in your VCR/DVD may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line mentioned on page 28 to locate
a Sharp Authorized Service Center.
Hint
• Remember to read the instructions along with the video head cleaner before use.
• Clean video heads only when problems occur.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
–6–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Setup
About the Video Cassettes and Discs
Playable Video Cassettes
Use only cassettes marked
with this unit.
Playable Discs
Playable
discs
Mark (logo)
Region code
Recorded
signals
Disc size
Digital video
(MPEG2)
12 cm
or
8cm
Disc types
DVD-Video
or
* 1,2,4,6
DVD-R
DVD-RW
* 1,2,3,4,5,6
Example
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
Setup
DVD+R
DVD+RW
* 1,2,3,4,5,6
Digital audio Example
Audio CD
Track 1
* 4,6
CD-R
CD-RW
Digital audio
or
MP3
12 cm
or
8cm
MP3
Example
Track 1
* 4,5,6
If you cannot play back a disc which bears one of the
marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs
recorded in other color systems such as PAL cannot be
played back.
*2: Certain DVD-Video discs do not operate as described in this
manual due to the intentions of the disc’s producers.
*3:
This label indicates playback compatibility with DVDRW discs recorded in VR mode (Video Recording
Format).
Track 2
Track 3
Track 4
Track 5
Track 4
Track 5
Group 1
Track 2
Track 3
Track 6
Group 2
Track 6
This player cannot play the DVD-RW that supports CPRM
(Contents Protection for Recordable Media).
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or
special properties of discs.
*6: You can play back discs which bear the marks above. If
you use nonstandardized discs, this unit may not play
them back. Even if they are played back, the sound or
video quality will be compromised.
Unplayable Discs
¡On the following discs, only the sound can be heard (picture cannot be viewed).
CDV,
CD-G
¡NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM, CD-I, Photo CD, Video CD, DVD with region codes other than 1 or ALL,
DVD-ROM for personal computers,
Hint
CD-ROM for personal computers
¡On the following disc, the sound MAY NOT be heard. • Only the sound recorded on the normal CD layer can be delivered.
Super Audio CD
The sound recorded on the high density Super Audio CD layer cannot be delivered.
¡Any other discs without compatibility indications.
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
RF Output Channel
If channel 3 is already occupied for broadcasting,
Hint
1) Set your TV to channel 4.
• The RF output channel may
2) Insert a pre-recorded tape into this unit.
not change when you adjust
3) Press the OUTPUT button on the VCR/DVD so that the VCR OUTPUT light is lit.
• If “VCR” light does not appear on the display of this unit, press the VCR/TV button on the remote control. tracking during playback. In
this case, stop the playback,
4) Press the PLAY button once.
and start the playback again.
5) After a few seconds, press the PLAY button on the VCR/DVD for 3 seconds.
After that, press the PLAY
• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
button on the VCR/DVD for 3
In this case, “ch04” will appears on the front panel.
seconds again.
• When a picture does not appear on the TV screen, repeat step 4.
6) Press the STOP button to stop playback.
–7–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Hint for Cable Box or Satellite Box
Connection A
(Cable box or
Satellite box)
IN
OUT
(Back of VCR/DVD)
Connection B
(Back of VCR/DVD)
ANT-IN
ANT-IN
Round Coaxial cable
ANT-OUT
Cable
Signal
Cable
Signal
E
(supplied)
(Back of TV)
ANT-OUT
IN
Round Coaxial cable (supplied)
Setup
Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed
on the VCR/DVD. You can view or record ONLY the channels you
have selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be
viewed.
To select channels of the cable box or satellite box
1) Turn on the VCR/DVD by pressing the POWER button, and
then, press the VCR/TV button.The “POWER” and “VCR” lights
on the front panel will appear. Then, press the SKIP/CH. (K/L)
buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).
• If you use the channel 4, you need to change the VCR/DVD’s
RF output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as you
have selected at step 1).
3) At the cable box or satellite box, select the channel you want to
view or record.
(Cable box or
Satellite box)
E
OUT
(Back of TV)
Round Coaxial cable
Select this connection when you want to change channels on the
VCR/DVD. With this connection, you may watch one channel
while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1) At the cable box or satellite box, select channel 3 or 4 (the
same channel as the VCR/DVD’s RF output channel.)
• Refer to “RF Output Channel”.
2) At the TV, select the same channel as the output channel (3 or
4) of the cable box or satellite box.
3) Turn on the VCR/DVD by pressing the POWER button, and
then, press the VCR/TV button. The “POWER” and “VCR” lights
on the front panel will appear. Then, select the channel you
want to view or record.
To play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 13.
To view one channel while recording another
1) While you are recording on the VCR/DVD, press the VCR/TV button so that the “VCR” light disappears on the VCR/DVD.
2) At the cable box or satellite box, select the channel you want to view.
Connection to an Audio System
Method 1
Method 2
Dolby Digital decoder, DTS decoder,
MD deck or DAT deck
Stereo system
Analog audio
input jacks
AUDIO
L
R
COAXIAL
Audio Coaxial
Digital cable
(commercially
available)
Audio cable
(supplied)
VCR/DVD
DVD/VCR
VCR
AUDIO OUT
AUDIO IN
L
(Analog)
AUDIO OUT
DIGITAL
AUDIO OUT
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
L
L
R
VIDEO OUT
Digital audio
input jack
COAXIAL
or
DIGITAL
AUDIO OUT
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
COAXIAL
CR/
PR
DVD
AUDIO
OUT
L
CB/
PB
R
VIDEO IN
DIGITAL
AUDIO OUT
CB/
PB
R
CR/
PR
Hint
• If the output is Dolby Digital-encoded audio, connect a Dolby Digital decoder and set “DOLBY DIGITAL” to “BITSTREATM”
for the AUDIO setting in the setup mode. (Refer to pages 23 and 25.)
• If the output is DTS-encoded audio, connect a DTS decoder and set “DTS” to “BITSTREAM” for the AUDIO setting in the
setup mode. (Refer to pages 23 and 25.)
• The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD
or DAT deck.
• Unless connected to a Dolby Digital and/or DTS decoder, set “DOLBY DIGITAL” and “DPCM” or “DTS” to “OFF” for audio
output in the setup mode. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the
speakers. (Refer to pages 23 and 25.)
• By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital 5.1 channel surround sound as heard in the movie theaters.
–8–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Connection to a TV
Basic Audio
TV
Method 1
Method 2
Method 3
Good picture
Better picture
Best picture
COMPONENT
VIDEO IN
AUDIO IN
L
R
Y
S-VIDEO IN
VIDEO IN
Y
PB
CB
or
PR
Video
cable
(supplied)
DVD/VCR
AUDIO OUT
VCR
DIGITAL
AUDIO OUT
DVD
AUDIO
OUT
DVD/VCR
S-VIDEO
OUT
AUDIO OUT
AUDIO IN
Y
L
L
CB/
PB
R
VCR
AUDIO OUT
L
DIGITAL
AUDIO OUT
AUDIO IN
L
R
R
VIDEO IN
R
R
COMPONENT
VIDEO OUT
Y
R
ANT-OUT
R
CR/
PR
VIDEO IN
VIDEO OUT
S-VIDEO
OUT
Component
Video cables
(commercially
available)
L
ANT-IN
VIDEO OUT
DVD
AUDIO
OUT
L
VCR
COMPONENT
VIDEO OUT
L
COAXIAL
DVD/VCR
AUDIO IN
L
COAXIAL
VIDEO IN
VIDEO OUT
CB/
PB
DIGITAL
AUDIO OUT
R
or
DVD
AUDIO
OUT
VIDEO OUT
S-VIDEO
OUT
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
CR/
PR
DIGITAL
AUDIO OUT
CR
Setup
Audio cable
(supplied)
VCR/DVD
S-Video
cable
(commercially
available)
L
S-VIDEO OUT
COAXIAL
COMPONEN
VIDEO OUT
CB/
PB
R
CR/
PR
L
COAXIAL
COMPONENT VIDEO OUT
R
Hint
• Connect this unit directly to the TV. If the A/V cables are connected to a
VCR, pictures may be distorted due to the copy protection system.
(Analog) AUDIO OUT
• The COAXIAL, DVD AUDIO OUT, S-VIDEO OUT, and COMPONENT VIDEO OUT jacks are only useful in DVD mode.
If your TV is compatible with 480p progressive scanning and you want to enjoy that high quality picture;
You must select the connection Method 3 above and progressive scanning mode. To set the mode, set “PROGRESSIVE” to
“ON” in the DISPLAY menu so that “P.SCAN” will appear on the display of this unit. (The progressive scanning is not available in the VCR mode.) See page 23 for more details.
If your TV is not compatible with progressive scanning;
Use this unit in interlace mode. Make sure that no “P.SCAN” is on the display of this unit. If so, set “PROGRESSIVE” to
“OFF” in the DISPLAY menu so that “P.SCAN” on the display of this unit will disappear.
Front & Rear Terminals
DVD ANALOG AUDIO OUT
jacks
Connect the supplied audio
cables here through the Audio
In jacks of a television or other
audio equipment. (DVD only)
COAXIAL jack
Connect an optional coaxial
digital audio cable here
through the coaxial digital
audio in jack of a decoder or
audio receiver. (DVD only)
S-VIDEO OUT jack
Connect an optional
S-Video cable here
through the S-video
in jack of a television. (DVD only)
DVD/VCR AUDIO OUT jacks
Connect the supplied audio
cables here through the audio
In jacks of a television or other
audio equipment.
DVD
DIGITAL
AUDIO S-VIDEO
OUT
AUDIO OUT OUT
COMPONENT
VIDEO OUT
DVD/VCR
VCR
AUDIO OUT
AUDIO IN
L
COAXIAL
DIGITAL
AUDIO OUT
S-VIDEO
OUT
R
COAXIAL
VIDEO OUT
R
L
RPC /
B
B
R
AUDIO OUT
FF
ST
EJ
ANT-IN
L
L
R
VIDEO IN
ANT-OUT
ANT-OUT
CR/
PR
CR/
PR
[Back of VCR/DVD]
DVD/VCR VIDEO OUT jack
Connect the supplied yellow
video cable here through
the TV’s video in jack.
–9–
Downloaded From DvDPlayer-Manual.com Sharp Manuals
L(MONO)-AUDIO-R
VCR
AUDIO IN
R
VIDEO OUT
VIDEO IN
AV IN 2
VIDEO
REW
DVD/VCR
COMPONENT
VIDEO OUT
Y
CB/
PB
COMPONENT VIDEO
OUT jacks
Connect optional component
video cables here through
the component video in
jacks of a television.
(DVD only)
AUDIO
OUT
ANT-IN
L
L
DVD
Y
AUDIO IN jacks
Connect audio cables coming
from the audio out jacks of a
ANT IN jack
camcorder, another VCR, or an Connect your antenna
audio source here.
or cable box here.
VIDEO IN jack
Connect a cable coming from the video out
jack of a camcorder,
another VCR, or an
audio-visual source
(laser disc player, video
disc player, etc.) here.
[Front of
VCR/DVD]
ANT OUT jack
Connect the
supplied Round
Coaxial cable to
the antenna
input jack on
your TV.
EN
About the Remote Control and Front Panel
VCR mode
DVD mode
Remote Control
POWER SPEED
1
Disc/Tape
Button
(Alphabetical order)
1
2
3
4
5
6
7
8
9
0
+10
AUDIO
2
SKIP CH.
5
6
7
8
9
• To select chapter or title directly
CD
MP3
• To select track directly
• To search forward/backward
through a disc
• To search forward/backward
• To begin slow forward/reverse
through a disc
playback during the pause mode
3
4
DVD-V
VCR TV
SLOW
DISPLAY
0
+10
VCR
DVD
ENTER
A-B
ANGLE
STOP
REC OTR
AUDIO
MENU
ENTER
• To repeat between your
chosen point A and B
• To repeat between your
chosen point A and B (CD)
CLEAR/
C.RESET
SEARCH CLEAR
MODE C.RESET
Setup
SUBTITLE ANGLE REPEAT
A-B
T-SET
DISPLAY
VCR / DVD COMBINATION
DVD
MENU
MODE
Installing the Batteries
for the Remote Control
PAUSE
Install two AA batteries
(supplied) matching the polarity indicated inside battery compartment of
the remote control.
POWER
PLAY
REPEAT
RETURN
2
SEARCH
MODE
SETUP
3
SKIP/CH.
Keep in mind the following when using
the remote control:
• Make sure that there is no obstacle between the remote and the
remote sensor on the unit.
• Use within the operating range
and angle, as shown.
ut
bo m)
a
in (7
ith t
W 3 fee
2
SKIP/CH.
• To forward/backward a tape
• To select an item
on the VCR Menu
• To advance to the next
VCR Menu
• To go back one step during
clock and timer setting
• To select audio languages on • To select STEREO,
a disc
L-CH or R-CH (CD)
• To clear the markers
• To clear the numbers
entered incorrectly
• To clear the markers (CD)
• To remove status number
in program input
• To clear the numbers
entered incorrectly
• To exit the VCR Menu
• To reset the tape counter
• To display the current disc
mode
• To display the current disc
mode
• To display the current time,
tape counter, and channel
• To select the DVD output
• To select the DVD output
mode
mode
• To activate the remote control • To activate the remote control
in DVD mode
in DVD mode
• To call up the Menu
on a disc
• To call up the MP3 menu
(MP3)
• To call up the VCR Menu
• To set black level on/off
• To arrange the playing
• To set virtual surround on/off
order or play randomly
• To set Rapid Play on/off
• To set virtual surround on/off
• To pause disc playback
• To advance playback
one frame at a time
• To pause disc playback
• To pause tape playback or
recording
• To advance playback
one frame at a time
• To begin disc playback
• To begin disc playback
• To begin tape playback
• To turn the unit on or off
• To turn the unit on or off
• To turn the unit on or off
• To start a recording or
One Touch Recording
REC/OTR
1
• To select channel
• The +10 button has no effect
in VCR mode.
• To select camera angles on
a disc
RETURN
SETUP TOP MENU
ZOOM
• To move the cursor and
determine its position
PAUSE
PLAY
MODE
• To move the cursor and
determine its position
VCR
• To play a track or disc
repeatedly (CD)
• To play a track, group or disc
repeatedly (MP3)
• To return to the previous
• To return to the previous
operation on the DVD setup
operation on the DVD setup
menu
menu
• To search track
• To search chapter, title or time • To search time (CD)
• To call up the index or time
• To rapidly return to
• To rapidly return to
search menu
a location of disc
a location of disc
• Search the markers.
• Search the markers. (CD)
• To play a chapter or title
repeatedly
• To call up the DVD setup
menu
• To call up the DVD setup
menu
• To skip chapters
• To skip tracks
• To change channels
• To adjust the tracking manually
during playback
SLOW
• To view the tape
in slow motion
SPEED
• To select the recording speed
STOP
SUBTITLE
• To stop playback
• To call up the Top Menu
on a disc
• To return to the top file of the
highest hierarchy in the program
and MP3 menu (MP3)
• To select the VCR output
mode
• To activate the remote control
in VCR mode
VCR
VCR/TV
ZOOM
• To stop playback or recording
• To put the VCR into standby
mode for a timer recording
• To select subtitles on a disc
T-SET
TOP MENU
• To stop playback
• To select DVD position or
TV position
• To select CD/MP3 position
or TV position
• To select VCR position or
TV position
• To magnify the part of picture
(x2/x4)
Remote
control
– 10 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Front Panel Display
Lights up when power is on.
DVD-V
Timer light lights up when a
timer recording is set.
CD
Lights up when the
A-B repeat function
is on.
Lights up when the
progressive scan
system is activated.
Lights up when the
repeat function is on.
POWER
MP3
Displays a type of the disc
which is inserted on the tray.
• DVD: DVD disc
• CD: Audio CD, MP3
OPEN/CLOSE
AV IN 2
VIDEO
L(MONO)-AUDIO-R
REW
FF
STOP/
EJECT
OUTPUT
PLAY
CH
REC TIMER
VCR
DVD
STOP
GROUP
PLAY
P.SCAN
DVD
DVD
( TRACKING )
CD
Lights up when
the ALL repeat
function is on.
Displays how long the current title
or track has been played back. When
a chapter or track is switched, the
number of a new title, chapter or
track is displayed.
Lights up when the
inserted disc comes
to a pause.
Lights up when the inserted
disc is being played back.
VCR
Opening the tray
Lights up
when a tape is
in the VCR/DVD.
Closing the tray
Lights up when
the VCR/DVD is
in VCR position.
This light does not
appear when the
VCR/DVD is in
TV position.
Lights up during
playback when
the repeat function
is on.
Loading the disc
VCR
Lights up when
the timer recording or an
OTR recording has been set.
Lights up during a recording.
Flashes when a recording
is paused.
REC
PM
When a disc or tape is
being played back
Lights up when
the playback is
in still or slow mode.
Lights up when
current time is P.M.
Works as a tape counter(hour,minute,second).
Also displays a channel number,
tape speed, remaining time for OTR or
current time.
Lights up when the inserted
cassette is being played
back.
VCR/DVD Switching
Because this product is a combination of a VCR and a DVD player, you must select first which
component you wish to operate with the OUTPUT button.
VCR MODE
POWER
Press the VCR button on the remote control.
(Verify that the VCR OUTPUT light is lit.)
OPEN/CLOSE
POWER SPEED
AUDIO
AV IN 2
VIDEO
L(MONO)-AUDIO-R
REW
FF
STOP/
EJECT
OUTPUT
PLAY
CH
REC TIMER
VCR
DVD
STOP
PLAY
DVD
1
2
3
4
5
6
7
8
9
0
+10
VCR
DVD
( TRACKING )
SKIP/CH.
VCR/TV
DVD MODE
Press the DVD button on the remote control.
(Verify that the DVD OUTPUT light is lit.)
VCR button
DVD button
SLOW
DISPLAY
PLAY
OUTPUT
VCR
PAUSE
STOP
DVD
REC/OTR
DVD OUTPUT
light
Hint
• Pressing only the OUTPUT button on the front
panel DOES NOT switch the mode of the remote
control. You MUST select the correct mode on the
remote control.
ENTER
MODE
OUTPUT button
ZOOM
RETURN
SEARCH CLEAR/
MODE C.RESET
SUBTITLE ANGLE REPEAT
A-B
T-SET
VCR / DVD COMBINATION
VCR OUTPUT
light
– 11 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
MENU
SETUP TOP MENU
EN
Setup
Lights up when playing back
in slow mode. (DVD)
No disc inserted
/ cannot read disc
Preparation for Use
Turn on the unit for the first
time
VCR
VCR
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
To Preset the Channel Again
To Change the On-Screen Language
2
POWER
Remote Control
TV Screen
LANGUAGE SELECT
B ENGLISH
or
[ON]
FRANCAIS
Setup
ESPAÑOL
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by pressing the K or L button. Then, press the B
button.
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing the K or L button. Then, press the CLEAR/C.RESET
button.
Hint
3
CH 01
AUTO SET UP
4
CLOCK SET
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing
the K or L button. Then, press the B button.
3) Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button.
After scanning, the tuner stops on the lowest memorized channel.
• If you accidentally select Spanish or
French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
the B button, and select ENGLISH. Finally,
press the CLEAR/C.RESET button.
or
MONTH DAY
03 / 15
YEAR
2004
HOUR MINUTE
–– : ––
AM/PM
––
Select the current year
5
CLOCK SET
or
MONTH DAY
YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE
05 : ––
AM/PM
––
Select the current hour
6
CLOCK SET
or
MONTH DAY
YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE
05 : 40
AM/PM
––
Select the current minute
Clock Set Up
VCR
VCR
Do you connect the cable from the cable box or
the satellite box to the VCR/DVD’s ANT IN jack?
1
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
Yes Press the MENU
button to exit
• Refer to “Hint for Cable Box
or Satellite Box” section on
page 8.
or
NO
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized in this unit by using the SKIP/CH.
(K/L) buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the B button once again.
-MENU-
MENU
YES
CLOCK SET
or
MONTH DAY
03 / ––
YEAR
––––
HOUR MINUTE
–– : ––
AM/PM
––
MONTH DAY
YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE
05 : 40
AM/PM
P M AM
B PM
Select “AM” or “PM”
To exit the CLOCK SET
screen.
Hint
Select the current month
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
3
• To go back one step, press the s button
(during the steps [2] to [7].)
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
CLOCK SET
or
MONTH DAY
03 / 15
YEAR
––––
HOUR MINUTE
–– : ––
AM/PM
––
Select the current day
– 12 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
or
8
2
CLOCK SET
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
Hint
You can select a channel by directly
entering channel using the Number buttons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
7
EN
VCR Functions
Playback
1
Before:
Turn on the TV and set it to
channel 3.
POWER SPEED
• If channel 3 is already occupied for broadcasting, see “RF Output Channel” section.
VCR
1
2
Remote Control
2
3
4
5
6
7
8
9
0
+10
DISPLAY
VCR
DVD
OPEN/CLOSE
AV IN 2
SLOW
VIDEO
L(MONO)-AUDIO-R
REW
STOP/
EJECT
FF
O
PLAY
VCR
CH
REC TIMER
DVD
PAUSE
2
( TRACKING )
PLAY
3 2
4
3
STOP
REC OTR
3
POWER
VCR TV
TV Screen
PLAYB
PLAY
1
SKIP CH.
* See page 11 to switch
the VCR/DVD function.
VCR
Hint
AUDIO
• When a tape without record tab is
inserted, the
VCR/DVD will start
playback automatically.
• Tracking will be
automatically
adjusted upon playback. To adjust the
tracking manually,
press the SKIP/CH.
(K/L) buttons.
4
[VCR/DVD]
STOP
STOP
STOP/EJECT
EJECT A
/
Recording & OTR (One Touch Recording)
3
Hint
1
• If channel 3 is already occupied for
broadcasting, see “RF Output Channel” section.
POWER SPEED
2
AUDIO
VCR
VCR
1
2
3
4
5
6
7
8
9
0
+10
DISPLAY
VCR
DVD
SKIP CH.
2
1
Remote Control
1
2
3
4
5
6
8
9
TV Screen
2
SKIP/CH.
7
POWER
OPEN/CLOSE
VCR TV
SLOW
AV IN 2
VIDEO
L(MONO)-AUDIO-R
REW
FF
STOP/
EJECT
PLAY
CH
REC TIMER
PAUSE
DVD
( TRACKING )
CH12
PLAY
• Select the
desired channel
0
with tab
3
SPEED
• Select the desired tape
speed
SP
Tape Speed
T60
1hour
3hour
T120
2hours
6hour
T160
2-2/3hours
8hour
REC/OTR
REC
You can select a fixed recording time by pressing the REC/OTR button repeatedly.
REC
(Normal recording)
OTR(0:30)
OTR(8:00)
5
STOP
STOP
OTR(1:00).....
5 4
6
STOP
REC OTR
MENU
ENTER
SETUP TOP MENU
RETURN
SEARCH CLEAR
Recording/Playback Time
Type of tape
SP mode
SLP mode
4
5
4
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, remove its record tab. To record
on it later, cover the hole with cellophane
tape.
VCR
• To view one channel while recording
another
1) While you are
recording on the
VCR/DVD, press the
VCR/TV button so
that the “VCR” light
disappears on the
VCR/DVD.
2) At the cable box
or satellite box,
select the channel
you want to view.
• If you have connected the VCR/DVD to
a cable box or satellite box, refer to
“Hint for Cable Box
or Satellite Box”
section on page 8.
Record tab
You CANNOT copy a DVD to a videotape.
OTR(7:30)
6
To stop recording temporarily (Pause mode)
[VCR/DVD]
STOP/EJECT
EJECT A
/
Press the PAUSE button.
• During the rec-pause mode, five C marks appear on the TV
screen. Each C mark represents one minute.
• Press it again to resume recording.
Other Operations
To cue or review picture during playback
(Picture Search)
Counter Reset
Hint
Press the g or h button.
• Press it again and the VCR/DVD will search in
super high speed. (in the SLP mode only)
Press the CLEAR/C.RESET button.
To play back in slow motion
• Still/Slow/Pause
mode will be
automatically
cancelled after 5
minutes to prevent damage to
the tape and the
video head.
• To return to
playback from
the Picture
Search/Still/
Slow mode,
press the PLAY
button.
To freeze the picture on TV screen during playback (Still mode)
Press the PAUSE button. Each time you press the
button, the picture will be forwarded by one frame.
• If the picture begins to vibrate vertically during the
still mode, stabilize the picture by pressing the
SKIP/CH. (K/L) buttons.
• If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if equipped.
Press the SLOW button during playback or the still
mode.
• If the noise bars appear on the TV screen, you can
reduce it by pressing the SKIP/CH. (K/L) buttons.
Auto Rewind
When a tape reaches its end during playback, fast-forward, or recording (except timer recording and One
Touch Recording), the tape will automatically rewind
to the beginning. After rewinding finishes, the
VCR/DVD will eject the tape.
– 13 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
VCR Functions
Before:
Turn on the TV and set it to
channel 3.
On-Screen Operations
VCR
VCR
1
To call up the main menu
3
2
3
4
5
6
7
8
9
0
+10
DISPLAY
VCR
DVD
VCR TV
-MENU-
MENU
1
SKIP CH.
To decide
SLOW
CHANNEL SET UP
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
PAUSE
AUTO SET UP
B MANUAL SET UP
PLAY
STOP
2
4
To select an item
To exit the menu
-MENUor
CLEAR/
C.RESET
REC OTR
1
4
MENU
OR
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
MENU
ENTER
RETURN
SETUP TOP MENU
MODE
ZOOM
SEARCH CLEAR
MODE C.RESET
SUBTITLE ANGLE REPEAT
A-B
2
3
4
T-SET
VCR / DVD COMBINATION
Recording Features
Timer Recording
•Insert a tape with its record tab into the VCR/DVD.
VCR
5
VCR
1
-MENUMENU
Select the desired start time
(hour)
9
ONE TIME PROGRAM
or
ONE TIME PROGRAM
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
or
PROGRAM NUMBER 4
DATE
0 5 / 0 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
CHANNEL
––
REC SPEED – –
VCR Functions
Select the desired recording speed
• To set another program after step [9], press the
B button. Then, continue with step [2].
Select the minute
CLEAR/
C.RESET
or
2
or
PROGRAM NUMBER 4
DATE
––/––
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL
––
REC SPEED – –
Select an empty program
number
10
3
T-SET
6
ONE TIME PROGRAM
PROGRAM NUMBER 4
or
B ONCE
DAILY
WEEKLY
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”
Select the desired month
ONE TIME PROGRAM
or
PROGRAM NUMBER 4
DATE
0 5 / 0 3 MON
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL
––
REC SPEED – –
Select the desired day
or
• You can program one
year in advance.
PROGRAM NUMBER 4
DATE
0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
CHANNEL
––
REC SPEED – –
AM
B PM
Select “AM” or “PM”
7
Repeat the procedure in steps 5
and 6 to set the end time.
8
ONE TIME PROGRAM
or
PROGRAM NUMBER 4
DATE
0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL
16
REC SPEED – –
Select the desired channel
• If you have connected the VCR/DVD to a
cable box or satellite box as the
Connection A on page 8, select the VCR
to channel 3 or 4 (the RF output channel
of the VCR). Then, select the desired
channel at the cable box or satellite box.
Leave the cable box or satellite box on for
timer recording.
– 14 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
SUBTITLE
• TIMER light lights up on the front panel,
and
appears in the front panel display.
The VCR/DVD will change to the DVD mode.
or
4
PROGRAM NUMBER 4
DATE
0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL
16
REC SPEED SP
B SP
SLP
Hint
• To go back one step, press the s button (during
the steps [3] to [9].)
To Check, Correct, or Cancel a
Timer Program
1) Press the SUBTITLE/T-SET button
then, the VCR button on the remote
control.
2) Select main menu by pressing the
MENU button.
3) Select "TIMER PROGRAMMING"
by pressing the K or L button.
Then, press the B button.
4) Select the program number which
you want to check by pressing the K
or L button. The details of the program you selected will appear on
the TV screen.
• Go to the digit you want to change
by pressing the B or s button.
Then, enter correct numbers by
pressing the K or L button.
• You may cancel the entire program
by pressing the s button while the
program number flashes.
5) Press the CLEAR/C.RESET button
to exit.
6) Press the SUBTITLE/T-SET button
to return to timer stand-by mode.
To cancel a Timer Recording in
progress
Press the STOP/EJECT button on
the VCR/DVD.
EN
Hint for Timer Recording
• If there is a power failure or the VCR/DVD has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a tape is not in the VCR/DVD or does not have the record tab, the TIMER and
lights flash and timer recording cannot be performed.
Please insert a recordable tape.
• If a tape ends during timer recording, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER and
lights flash. (If the DVD power is off, the VCR will become STANDBY status).
• When all timer recordings are finished, the TIMER and
lights will flash.
• When timer recordings are set, theTIMER and
lights will appears. To use the VCR as usual until the time for the recording, press the
SUBTITLE/T-SET button so that the TIMER and
lights disappear. Press the VCR/TV button to choose the VCR position. Select either
VCR or DVD mode, then continue with the other features as described in this manual.
If you want to use the DVD player during a VCR timer recording or while the TIMER and
lights are on or flashes.
• You can use the DVD player while the TIMER and
lights are on or flashes, or during a timer recording. Press the POWER button to
turn on the VCR/DVD. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as
described in this manual. You don’t have to set the TIMER off to use the DVD only.
Copying a Video Tape
Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording
VCR/DVD.
3) Press the SPEED button on the remote control of the
or
Connect
recording VCR/DVD to select the desired recording
Connect
speed (SP/SLP).
4) Select the "L1" or "L2" position on the recording VCR/DVD.
Round Coaxial cable
(supplied)
• To use the input jacks on the back of this unit, select
Audio/Video cables
*Front input jacks are also available
(supplied)
"L1" position by pressing [0], [0], [1] on the remote
K/L
L) buttons.
control or the SKIP/CH. (K
Hint
• To use the input jacks on the front of this unit, select
"L2" position by pressing [0], [0], [2] on the remote
• For best results during dubbing, use the front panel controls whenever possible. The
K/L
L) buttons.
control or the SKIP/CH. (K
remote control might affect another source’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio
5) Press the REC button on the recording VCR/DVD.
cables are not recommended.
6) Begin playback of the tape in another source.
• You can use a video disc player, satellite receiver, or other audio/video component with
7) To stop recording, press the STOP/EJECT button on
A/V outputs.
the recording VCR/DVD, then stop playback of the tape
• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)
in another source.
(Back of TV)
(Back of another source)
AUDIO OUT
VCR
AUDIO IN
ANT-IN
Y
L
CB
R
L
R
DVD
AUDIO
S-VIDEO
OUT
OUT
DIGITAL
AUDIO OUT
DVD/VCR
COMPONENT
VIDEO OUT
AUDIO OUT
2
VCR
AUDIO IN
ANT-IN
Y
L
L
CB
R
R
L
R
VIDEO IN
VIDEO OUT
VIDEO OUT
ANT-OUT
CR
COAXIAL
VIDEO OUT
R
VIDEO IN
ANT-OUT
CR
• “L2” input jacks are on the front of this VCR/DVD.
MTS System (Multi-Channel Television Sound)
When You Receive or Record a
Program Broadcast in MTS
• When you receive a broadcast on
the VCR, you can check the type
of the broadcast by pressing the
DISPLAY button.
• When "TV STEREO" or "SAP"
selection is valid, select them by
following steps. This selection is
needed when you record the program.
• SAP means Second Audio
Program (usually second language).
VCR
VCR
VCR
1
VCR
1
MENU
-MENU-
or
-MENU-
MENU
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
B AUDIO OUT
TV STEREO
[ON]
SAP
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
B TV STEREO
[ON]
SAP
or
Select “TV STEREO” or
“SAP”
2
To exit the menu.
CLEAR/
C.RESET
2
AUDIO OUT
B HIFI
Display on the
TV screen
Type of
broadcast
STEREO/SAP
Selection
-None-
Regular
(monaural audio)
-Invalid-
STEREO
Stereo
broadcast
SAP
Bilingual
broadcast
STEREO
SAP
Stereo &
Bilingual
broadcast
-InvalidTV STEREO
(main audio program)
SAP
(second audio program)
TV STEREO
(stereo main audio program)
SAP
(second audio program)
When You Play Back a Tape
Recorded in Hi-Fi Stereo
• If you have connected a stereo TV to
this VCR/DVD, select "STEREO".
• If you have connected a monaural TV
to this VCR/DVD, select "MONO".
Your Selection
STEREO
[ON]
MONO
Select “HIFI” or “MONO”
MONO
Type of recorded tape
L-channel
R-channel
non Hi-Fi tapes
Monaural
Monaural
Monaural
Hi-Fi tapes
recorded in
Hi-Fi stereo
L
R
L+R
Hi-Fi tapes
recorded main
audio program
Main audio
program
Main audio
program
Main audio
program
Hi-Fi tapes
recorded second
audio program
3
To exit the menu.
CLEAR/
C.RESET
Second audio Second audio Second audio
program
program
program
– 15 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
or
EN
VCR Functions
AUDIO OUT
1
L
DVD/VCR
COMPONENT
VIDEO OUT
(Back of Recording VCR/DVD*)
Special Features
Time Search
Index Search
You can specify the time for fast
forwarding or rewinding.
• Insert a tape into this unit.
You can specify the number of programs to be skipped.
• Insert a tape into this unit.
VCR
VCR
VCR
VCR
VCR
1
TIME SEARCH
x2 (Twice)
VCR
1
1
INDEX SEARCH
SEARCH
MODE
–:––
SEARCH
MODE
2
Auto Repeat
You can repeat playback of a
whole tape automatically.
• Insert a tape into this unit.
x1 (Once)
Select the desired length of
time for fast forwarding or
rewinding
or
2
03
or
2
or
01 ~ 20
CURRENT PROGRAM
Beginning
of tape
VCR Functions
Pro.1
0:01~ 9:59
(1 minute~9 hours
and 59 minutes)
02
Pro.2
01
Pro.3
01
End
of tape
Pro.4
02
Pro.5
03
INDEX MARK
3
3
To rewind
To fast forward
To fast forward
After searching,
4
PLAY B
AUTO REPEAT B
Hint
After searching,
4
-MENUTIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
2:50
To rewind
-MENUTIMER PROGRAMMING
B AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
INDEX SEARCH
TIME SEARCH
3
MENU
––
• To cancel Auto Repeat, follow steps [1]-[2] above.
Then, press the B button, so that [OFF] appears
beside AUTO REPEAT. Press the
CLEAR/C.RESET button to exit.
• If menu remains on the TV screen at step [3],
press the CLEAR/C.RESET button to exit.
PLAY B
Hint
• This unit stores index mark at the beginning of
the recording. There should be time gap between
two index marks for the Index Search.
Hint f or Timer Sear c h & Inde x Sear c h
• These functions are not available during recording.
• Press the STOP button to stop the search.
• If the end of the tape is reached during a Search, this unit will cancel the search and rewind the tape.
– 16 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
DVD Functions
Playback
Before: Turn on the TV, amplifier and any other components which
are connected to this unit. Make sure the TV and audio receiver
(commercially available) are set to the correct channel.
DVD-V
CD
VR mode
(
MP3
1
)
1
2
3
4
5
6
VCR TV
7
8
9
0
+10
DISPLAY
VCR
DVD
SLOW
3
4
2
[VCR/DVD]
POWER
1
SKIP CH.
⇒p.19
* See page 11 to switch
the VCR/DVD function.
DVD
AUDIO
OPEN/CLOSE
PAUSE
PLAY
STOP
REC OTR
2
3
Remote Control
TV Screen
4
STOP
PLAY
POWER
OPEN/CLOSE
AV IN 2
VIDEO
L(MONO)-AUDIO-R
REW
STOP/
EJECT
FF
OUTPUT
PLAY
VCR
CH
REC TIMER
DVD
STOP
PLAY
DVD
( TRACKING )
5
[VCR/DVD]
OPEN/CLOSE
1
1
5
DVD menu
Paused and Step-by-Step Playback
DVDs may contain menus to access special features. Press
appropriate Number buttons or use the arrow (K/L/s/B)
buttons to highlight your selection on the DVD main menu
and press the ENTER button to confirm.
Calling up a Menu Screen during Playback
• Press the MENU button to call up the DVD menu.
• Press the TOP MENU button to call up the title menu.
DVD-V
DVD-V
VR mode
CD
MP3
Press the PAUSE button during playback.
To continue
k, press the PLAY
continue playbac
playback,
PLAY
b utton.
DVD-V
DVD-V
VR mode
The disc goes forward by one frame each time the PAUSE
button is pressed during the pause mode.
To continue
k, press the PLAY
continue playbac
playback,
PLAY button.
button.
Hint
• Menu operations may vary depending on the disc. Refer to
the manual accompanying the disc for details.
Hint
• Set “STILL MODE” to “FIELD” in the Display menu if pictures
in the pause mode are blurred. (Refer to pages 23-24.)
Resume
DVD-V
4 3
• When you play an MP3
file, details on page 19.
• A “prohibited icon” may
appear at the
top-right on
the TV screen
when the operation is
prohibited by the disc or
this unit.
• Some DVDs may be
played from title 2 or 3
due to specific programs.
• During the playback of a
two-layered disc, pictures may stop for a
moment. This happens
while the 1st layer is
being switched to the
2nd layer. This is not a
malfunction.
• A DVD-RW disc recorded in the VR mode may
freeze momentarily during playback depending
on how the playlist was
made and edited (deleted titles, repeated
recording).
DVD-V
VR mode
Rapid Play
CD
DVD-V
Press the STOP button. Resume message will appear on
the TV screen.
Press the PLAY button, playback will resume from the point
at which playback was stopped.
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
• To cancel resume, press the STOP button one more time
during the Stop mode.
• For MP3, playback will resume from the beginning of the
track at which playback was stopped.
Available only on discs recorded in the Dolby Digital format,
Rapid Play plays back in slightly faster/ slower speed while
keeping the sound quality as in the normal playback.
1) During playback, press the
OFF
MODE button.
• The current setting appears.
2) Press the ENTER button to switch among
(x0.8) and OFF.
: Plays back approximately at 0.8 times of normal
playback.
: Plays back approximately at 1.3 times of normal
playback.
3) To return to normal playback, press the PLAY button.
Hint
• Audio (language) setting cannot be changed while using
this mode.
• Virtual Surround and Black Level settings cannot be
changed while using this mode.
• Virtual Surround does not function while using this mode.
• This feature may not work at some point in a disc.
• When using digital audio connection (COAXIAL), the PCM
sound will be output.
– 17 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
(x1.3),
EN
DVD Functions
DVD-V
Hint
POWER SPEED
Playing the disc recorded in VR mode
(Video Recording format)
Zoom
DVD-V
DVD-V
VR mode
DVDs recorded in VR mode can have a PLAYLIST assigned
to alter the order or content to be played. If a PLAYLIST has
been created, you can choose the ORIGINAL or PLAYLIST
option.
1) Press the MENU button in stop mode.
• The current setting screen will appear.
• Pressing the MENU buttton during playback is not
valid.
ORIGINAL
PLAYLIST
1 PLAYLIST1
2 PLAYLIST2
3 PLAYLIST3
4 PLAYLIST4
5 PLAYLIST5
6 PLAYLIST6
DVD-V
VR mode
1) Press the ZOOM button during playback.
2) Press the ZOOM button repeatedly to select the
required zoom factor: x2, x4 or OFF.
x2
x4
K/L
L/s
s/B
B) buttons to slide the zoomed
3) Use the arrow (K
picture across the screen.
4) To exit zoom mode, press the ZOOM button to select OFF.
Hint
2) Press the s or B button to select ORIGINAL or
PLAYLIST.
• PLAYLIST will not be displayed when it has not been
made.
• Resume playback will not be possible if you change the
setting.
3) Press the K or L button to select a title, then press the
ENTER button.
• Playback will start.
• Zooming function does not work while the disc menu is
showing up.
• x4 zoom is not available on some discs.
Hint
• [ORIGINAL]: A list of titles which are recorded with a DVD
recorder.
[PLAYLIST]: A list of titles which is made based on the
ORIGINAL edited list.
Fast Forward/Reverse
DVD-V
DVD-V
VR mode
CD
MP3
DVD Functions
Press the g or h button repeatedly during playback to select the required forward or
reverse speed.
To continue
k, press the PLAY
continue playbac
playback,
PLAY button.
button.
• For DVDs, fast forward or reverse speed is different
depending on the disc. Approximate speed is
1(x2),2(x8),3(x50),4(x100).
• For Audio CDs, approximate speed is x16.
• For MP3, approximate speed is x8.
E1
Slow Forward/Slow Reverse
DVD-V
DVD-V
VR mode
1
Press the g or h button repeatedly during the pause mode to select the required forward or reverse speed.
To continue
k, press the PLAY
continue playbac
playback,
PLAY button.
button.
• Slow forward or reverse speed is different depending on
the disc. Approximate speed is 1(1/16),2(1/8),3(1/2).
Hint
• Set “STILL MODE” to “FIELD” in the Display menu if pictures in the slow playback mode are blurred.
(Refer to pages 23-24.)
– 18 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
MP3 Playback
MP3 is a method of compressing files. You can copy MP3 files on CD-RW/Rs from the computer and play the files on this unit.
2
DVD
MP3
STOP
Insert a MP3-format disc, then press
the MENU button to call up the MP3
menu on the TV screen.
1
Hint
MENU
FILE LIST
FOLDER
MP3
ENTER
PLAY
ENTER
DISC NAME
folder name 1
folder name 2
folder name 3
folder name 4
file name 1
file name 2
file name 3
1/2
folder name 1
When selecting the folder:
• Press the B button when you
want to go to the next hierarchy.
• Press the s button when you
want to go back to the previous hierarchy.
• Some selections may take a while to be recognized.
• Press the TOP MENU button to return to the first item.
• Folders are known as Groups; files are known as Tracks.
• MP3 files are accompanied by 3 icon.
• Folders are accompanied by
icon.
• A maximum of 255 folders can be recognized.
• A maximum of 512 files can be recognized.
• Up to 8 hierarchies can be created.
This player recommends the files recorded under the following circumstances:
• Sampling frequency: 44.1kHz or 48kHz
• Constant bit rate: 112kbps ~ 320kbps
The On-Screen Display
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
DVD
DVD-V
DVD
DVD-V
CD
VR mode
DISPLAY
DISPLAY
Current playback status
4/12 0:03:21 - 0:02:15
Current playback status
T
Remaining time of the current track
11/16 0:00:00 - 0:03:30
Remaining time of the current chapter
Elapsed time of the current track
DISPLAY
DISPLAY
C(Chapter):
Current chapter number / Total chapters
4/12 0:13:45 - 0:45:40
1/3
T
0:00:00 - 1:23:45
Remaining time of the current title
Elapsed time of the current title
DISPLAY
T
T(Title):
Current title number / Total titles
DISPLAY
ALL:
Current track number / Total tracks
Current repeat setting appears only when
the repeat setting is active
T: Track repeat
A: All Tracks repeat
A B: A-B repeat
Remaining time of the current audio CD
Elapsed time of the current audio CD
L1
DISPLAY
Layer numbers, appears only when playing
a two-layered Disc
L0: Layer 0 is playing
L1: Layer 1 is playing
If you are playing a DVD-RW with setting
the PLAYLIST, the following will also be displayed.
ORG: Playing the ORIGINAL.
PL: Playing the PLAYLIST
Current repeat setting appears only when
the repeat setting is active
C: Chapter repeat / T: Title repeat /
A B: A-B repeat
A: Disc repeat (DVDs recorded in VR
mode only)
BIT RATE: The amount of audio and video
data currently being read
DISPLAY
Current playback status
TRACK 01
The name of the file currently in play
will be displayed.
DISPLAY
1/36 0:01:15
T
T(Track):
Current Track number / Total Tracks
Current Repeat setting, if active
T: Track repeat
G: Group (folder) repeat
A: Disc repeat
Elapsed playing time of the current track
DISPLAY
– 19 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
DVD
MP3
EN
DVD Functions
T(Track):
Current track number / Total tracks
Elapsed time of the current chapter
Search Function
Track Search
Title / Chapter Search
DVD
CD
MP3
Using the number buttons
1
1
2
3
4
5
6
7
8
9
0
+10
DVD
DVD-V
DVD-V
Time Search
Using the SEARCH MODE button
1
/12
SEARCH
MODE
DVD-V
DVD-V
VR mode
VR mode
CD
DVD
1
PLAY
/2
TOTAL 1:29:00
•For single digit tracks (1-9), press a
single number (eg. track 3, press 3).
•To play track 26, press +10, 2, 6 of the
Number buttons.
x1(Press once) for the chapter search
x2 (Press twice) for the title search
2
1
2
3
4
5
6
7
Using the SEARCH MODE button
1
8
0
/12
repeatedly until this
screen appears
SEARCH
MODE
2
1
2
3
4
5
6
7
8
9
TOTAL 1:29:00
9
+10
Within 30 seconds
0
Within 30 seconds
SEARCH
MODE
/2
2
1
2
3
4
5
6
7
8
9
0
+10
Using the SKIP H , G buttons
1
PLAY
/2
Current Chapter
(CH)
Within 30 seconds
SKIP/CH.
Using the SKIP H , G buttons
1
PLAY
Current Track
(TR)
SKIP/CH.
SKIP
TR 1 TR 2 TR 3 TR 4
SKIP
• When there is no need to enter a
number, “0” appears automatically. For
example, “0:0_:_ _” appears in the
Time Search display if the total time
of the disc is less than 10 minutes.
SKIP
CH 1 CH 2 CH 3 CH 4
SKIP
Hint
DVD Functions
• Depending on the disc being played,
this function can also be performed
by directly entering the desired chapter number with the number buttons.
Refer to the manual accompanying
the disc.
Marker Setup
DVD-V
DVD-V
VR mode
CD
DVD
To return to the marker
later
1
This feature allows you to assign a specific
point on a disc to be called back later.
SEARCH
MODE
PLAY
1
RETURN
PLAY
To set a marker
1
To e xit the marker screen
repeatedly until this
screen appears
Hint
SEARCH
MODE
repeatedly until this
screen appears
2
or
2
or
3
ENTER
3
at the desired marker
ENTER
•Playback will restart from the specific point
which you set.
– 20 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
• Opening the disc tray or turning off
the power will erase all markers.
• Selecting “AC” at step [2] in the section “To set a marker” will also erase
all markers.
• To clear a marker, select the marker
to be cleared at step [2] in the section “To return to the marker later,”
and then press the CLEAR/C.RESET
button.
EN
Repeat / Random / Programmed Playback
Repeat Playback
Repeat A-B Playback
DVD
DVD-V
Repeat function is available only during
playback.
1
Programmed Playback
DVD
DVD-V
CD
VR mode
CD
MP3
You may determine the order in which
tracks will play.
DVD
1
1
STOP
PLAY
CD-DA
TOTAL 0:00:00
CD-DA
TOTAL 0:08:00
A-
PLAY
ENTER
MODE
A-B
REPEAT
at your desired starting point (A)
2
2
A-B
or
A-B
DVD-V
8 3:30
9 2:30
10 1:30
ALL CLEAR
CHAPTER (current chapter repeat)
ENTER
at your desired end point (B)
TITLE
(current title repeat)
• Point B should be in the same title
ENTER
or track as point A is.
OFF
(repeat off)
¡To exit the sequence, press the A-B
button.
DVD-V
¡To cancel Point A, press the
VR mode
CHAPTER (current chapter repeat)
TITLE
(current title repeat)
ALL
(entire disc repeat)
OFF
(repeat off)
CLEAR/C.RESET button.
¡This function does not work in the
other repeat modes.
Random Playback
DVD
CD
TRACK
(current track repeat)
ALL
(entire disc repeat)
MP3
1
RANDOM
STOP
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
OFF
(repeat off)
TRACK
(current track repeat)
GROUP
(current group repeat)
ALL
(entire disc repeat)
OFF
(repeat off)
MODE
PLAY
x2 (Press twice)
MP3
¡Repeat setting will be cleared when
moving to another title, chapter, or
track.
¡Repeat playback are not available
with all discs or during repeat A-B
playback.
2
PLAY
Hint
• If you want to repeat the current track
in the random selections, press the
REPEAT button repeatedly until
TRACK appears during playback.
If you want to repeat the entire random selections, press the REPEAT
button repeatedly until
ALL
appears during playback.
– 21 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
Up to 99 programs can be
stored.
While a MP3 folder is open:
• For the next hierarchy,
press the B button.
• For the previous hierarchy,
press the s button.
3
PLAY
This shuffles the playing order of tracks
instead of playback in the sequence.
CD
2/2
8 3:30
Hint
• Press the CLEAR/C.RESET button at
step [2] to erase the most recently
entered program.
• To erase all tracks in the program at
once, select “ALL CLEAR’’ and press
the ENTER button at step [2].
• While a program is being played
back, the STOP button works as follows;
⇒Press the STOP button and the
PLAY button next, so that the programmed playback restarts. (CD
playback restarts from the current
point. MP3 playback restarts from
the beginning of the current track.)
⇒Press the STOP button twice and
the PLAY button next, so that playback restarts from the first track in
the original order. However, your
programmed playback can be
restarted when you follow the above
steps. (Your programs are still stored
until either the disc tray is open or
power is turned off.)
• To repeat the current track in the program, press the REPEAT button
repeatedly until “
TRACK’’ appears
during playback.
• To repeat the entire program press
the REPEAT button repeatedly until
“
ALL’’ appears during playback.
EN
DVD Functions
Each time the REPEAT button is pressed...
x1 (Press once)
Special Settings
Subtitle Language
Audio Language
DVD
DVD-V
DVD-V
DVD-V
VR mode
Camera Angle
DVD-V
VR mode
This unit allows you to select a subtitle
language (if available) during DVD playback.
This unit allows you to select an audio
language (if multiple languages are
available) during DVD playback.
1
1
PLAY
1.ENG/6
DVD
DVD
DVD-V
PLAY
1.ENG
3/2.1ch 48k/3
Some DVD discs may contain scenes which have
been shot simultaneously
from various angles. You can change
the camera angle if the (
) icon
appears on the screen. If the “ANGLE
ICON” setting is “OFF” in the Display
menu, the (
) icon will not appear.
(Refer to pages 23-24.)
AUDIO
SUBTITLE
1
T-SET
Each time you press the SUBTITLE/TSET button, subtitle languages change.
Each time you press the AUDIO button;
For example
ENG
ENG
(English audio)
SPA
(Spanish audio)
1/8
ANGLE
(English subtitles)
(French subtitles)
Stereo Sound mode
...
...
FRE
PLAY
For example
FRE
OFF
(no subtitles)
Hint
To set subtitle ON/OFF
1
PLAY
1.ENG/6
SUBTITLE
T-SET
DVD Functions
2
OFF
Hint
• If your language is not shown after
pressing the AUDIO or SUBTITLE/TSET button several times, the disc
may not have that language.
However, some discs allow audio language or subtitle language setting on
the disc menu. (Operation varies
depending on the discs, so refer to
the manual along with the disc.)
• When “NOT AVAILABLE” appears on
the TV screen, it means no subtitle is
recorded on the scene.
• If you choose a language that has a
3 letter language code, the code will
be displayed every time you change
the subtitle language setting. If you
choose any other languages, ‘---’ will
be displayed instead. (Refer to page
27.)
• For DVD-RW (VR mode), Pressing
the AUDIO button cycles the sound
mode through MAIN, SUB, MAIN +
SUB.
• For DVD-RW (VR mode), the discs
recorded in double sound (two languages ) can be played back in either
sound mode of MAIN, SUB or MAIN
+ SUB.
• The sound mode cannot be changed
during playback of discs not recorded
in double sound.
• Audio language selection cannot be
made during Rapid Play. (Refer to
page 17.)
• Pressing the AUDIO button may not
work on some DVDs with multiple
audio languages (e.g. DVDs which
allow audio language setting on the
disc menu).
• With discs recorded in VR mode,
changing the audio (MAIN, SUB or
MAIN+SUB) is effective only when
using an analogue connection.
Although you may be able to change
the settings of the on-screen display,
it will not affect the sound when using
a digital connection.
– 22 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
DVD
(French audio)
CD
This unit allows you to select a sound
mode during CD playback.
1
PLAY
STEREO
AUDIO
Each time you press the AUDIO button;
STEREO (right and left channels
are active)
(left channel is active)
L-CH
R-CH
(right channel is active)
Hint
• If the Virtual Surround setting is “1’’ or
“2’’, the sound mode will be fixed to
STEREO, and cannot be changed.
• Stereo sound mode will not be
changed when playing DTS CD.
EN
Hint
Black Level Setting
DVD
DVD-V
DVD-V
VR mode
Adjust the Black Level Setting to make
the dark areas of the TV picture brighter.
1
DVD-V
repeatedly until this
screen appears
MODE
1: Natural effect
2: Emphasized effect
OFF: No effects (original sound)
3
DVD-V
Hint
MP3
ENTER
You can enjoy stereophonic virtual world
on your existing 2 channel stereo system.
OFF
1
ON: Makes the dark areas brighter.
OFF: Shows the original picture as recorded.
3
PLAY
OFF
RETURN
MODE
RETURN
CD
VR mode
DVD
2
1
ENTER
Virtual Surround
ON
PLAY
2
• The setting will be saved even if the
player is turned off.
• This function cannot be used during
Rapid Play. (Refer to page 17.)
• The setting will not be effective
unless the sound mode is set to
STEREO. (for CD play only)
• This function cannot be used during
Rapid Play. (Refer to page 17.)
• The setting will be saved even if the
player is turned off.
repeatedly until this
screen appears
DVD
DVD Set Up
Q UICK SETUP Men u
You can select the “PLAYER MENU”, “TV ASPECT”, “DOLBY DIGITAL” or “DTS” from the QUICK SETUP menu quickly.
1
2
or
SETUP
STOP
Select the desired item
<SETUP MENU>
Confirm that QUICK is selected
QUICK SETUP
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
DTS
QUICK SETUP
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
DTS
ENGLISH
4:3 LETTER BOX
BITSTREAM
OFF
P24 A (Step 5)
P24 B (Step 5)
P25 C (Step 5)
ENGLISH
4:3 LETTER BOX
BITSTREAM
OFF
DVD Functions
ENTER
ENTER
•Refer to the sections “PLAYER MENU”,
“TV ASPECT”, “DOLBY DIGITAL” or
“DTS” section on pages 23-25.
CUSTOM Men u
You can change the DVD player’s settings.
1
2
SETUP
STOP
3
or
ENTER
to decide
To select the desired item
Select CUSTOM
<SETUP MENU>
or
ENTER
QUICK SETUP
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
DTS
LANGUAGE menu
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
QUICK SETUP
ENGLISH
4:3 LETTER BOX
BITSTREAM
OFF
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
DTS
DISPLAY menu
DISPLAY
TV ASPECT
STILL MODE
ANGLE ICON
PROGRESSIVE
ORIGINAL
OFF
ENGLISH
ENGLISH
page 24 A
ENGLISH
4:3 LETTER BOX
BITSTREAM
OFF
AUDIO menu
AUDIO
4:3 LETTER BOX
AUTO
ON
OFF
DRC
ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
DTS
OFF
page 24 B
page 25 C
– 23 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ORIGINAL
OFF
ENGLISH
ENGLISH
PARENTAL menu
PARENTAL
PASSWORD
Please enter a 4-digit password.
page 26 D
EN
A
LANGUAGE Setting
Follow the step 1) to 3) in the “CUSTOM Menu” section on page 23.
4
5
Select the desired item
or
ORIGINAL
OFF
ENGLISH
ENGLISH
AUDIO ∗1 ∗2
(Default: ORIGINAL)
Sets the audio language.
AUDIO
ORIGINAL
ENGLISH
FRENCH
SUBTITLE: ∗1 ∗2
(Default: OFF)
Sets the subtitle language.
SUBTITLE
OFF
ENGLISH
FRENCH
DISC MENU: ∗1
(Default: ENGLISH)
Sets the language for DVD
menu.
DISC MENU
ENGLISH
FRENCH
SPANISH
PLAYER MENU: QUICK
(Default: ENGLISH)
Sets the language for the
On-screen display.
B
To exit the menu
ENTER
or
LANGUAGE menu
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
6
Select the desired language
ENTER
SETUP
Hint
∗1
• Language options are not available with
some discs.
• If OTHER is selected on the AUDIO, SUBTITLE or DISC MENU screen, press four-digit
number to enter the code for the desired language. (Refer to the language code list on
page 27.)
• Only the languages supported by the disc
can be selected.
∗2
• Language Setting for Audio and Subtitle is
not available with some discs. Then use the
AUDIO and the SUBTITLE/T-SET button.
Details are on page 22.
PLAYER MENU
ENGLISH
FRANÇAIS
ESPAÑOL
DISPLAY Setting
You can change the display functions. Follow the step 1) to 3) in the “CUSTOM Menu” section on page 23.
4
Select the desired item
or
5
6 To exit the menu
SETUP
TV ASPECT: QUICK
(Default: 4:3 LETTER BOX)
See Tips to the right.
Select the
desired
setting
TV ASPECT
TV ASPECT
4:3 LETTER BOX
STILL MODE
AUTO
ANGLE ICON
ON
PROGRESSIVE OFF
DISPLAY menu
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
or
ENTER
Hint
ENTER
DVD Functions
DISPLAY
TV ASPECT
STILL MODE
ANGLE ICON
PROGRESSIVE
4:3 LETTER BOX
AUTO
ON
OFF
STILL MODE:
(Default: AUTO)
See Tips to the right.
Select the
desired
setting
STILL MODE
TV ASPECT
4:3 LETTER BOX
STILL MODE
AUTO
ANGLE ICON
ON
PROGRESSIVE OFF
AUTO
FIELD
FRAME
or
ENTER
ANGLE ICON:
(Default: ON)
Set to “ON” to show the angle icon when multiple camera
angles are available during DVD playback.
TV ASPECT
4:3 LETTER BOX
AUTO
STILL MODE
ANGLE ICON
ON
PROGRESSIVE OFF
4:3 LETTER BOX
AUTO
OFF
OFF
ENTER
PROGRESSIVE:
(Default: OFF)
Set to “ON” if your TV is compatible with progressive scan.
When “PROGRESSIVE” is “ON”, “P. SCAN” appears on the
front panel display.
TV ASPECT
4:3 LETTER BOX
STILL MODE
AUTO
ANGLE ICON
ON
PROGRESSIVE OFF
ENTER
TV ASPECT:
• Select “4:3 LETTER BOX”, so
that black bars appear on the
top and bottom of the screen.
• Select “4:3 PAN & SCAN” for
a full height picture with both
sides trimmed.
• Select “16:9 WIDE” if a widescreen TV is connected to this
unit.
STILL MODE:
• Select “AUTO” usually.
• If you select “FIELD”, the picture in the still mode will be
stabilized.
• If you select “FRAME”, the
picture in the still mode will be
highly defined.
4:3 LETTER BOX
AUTO
ON
ON
ENTER
– 24 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
C
AUDIO Setting
Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow the step 1)
to 3) in the “CUSTOM Menu” section on page 23.
4
Select the desired item
6 To exit the menu
DRC
DOWN SAMPLING
DOLBY DIGITAL
DTS
AUDIO menu
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
DTS
5
SETUP
DRC (Dynamic Range Control):
(Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
or
ON
ON
BITSTREAM
OFF
ON
ON
BITSTREAM
OFF
ENTER
OFF
ON
BITSTREAM
OFF
DOWN SAMPLING:
(Default: ON)
Set to “ON” when outputting in 48 kHz.
Set to “OFF” when outputting the original sound.
DRC
DOWN SAMPLING
DOLBY DIGITAL
DTS
ON
ON
BITSTREAM
OFF
ON
OFF
BITSTREAM
OFF
ENTER
Hint
DRC:
• This function is available only
on the discs which are recorded in the Dolby Digital format.
DOWN SAMPLING:
• When playing disc with copyright Protection, the sound will
be down sampled at 48kHz,
even if you set to OFF.
• This function is available only
on digital outputting of a disc
recorded in 96kHz.
DOLBY DIGITAL: QUICK
(Default: BITSTREAM)
Set to “BITSTREAM” when the unit is connected to a Dolby Digital receiver.
• BITSTREAM: Outputs a Dolby Digital Signals
• DPCM: Convert the Dolby Digital into PCM (2 channel)
DRC
DOWN SAMPLING
DOLBY DIGITAL
DTS
ON
ON
BITSTREAM
OFF
ON
ON
DPCM
OFF
ENTER
DTS: QUICK
(Default: OFF)
Set to “BITSTREAM” when the unit is connected to a DTS decoder.
ON
ON
BITSTREAM
OFF
ON
ON
BITSTREAM
BITSTREAM
DVD Functions
DRC
DOWN SAMPLING
DOLBY DIGITAL
DTS
ENTER
– 25 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
D
PARENTAL Setting
Parental Control limits the disc viewing that exceed your settings. (if an incorrect password is entered, the disc will not play)
This feature prevents your children from viewing inappropriate materials.
Parental Le vels
Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set.
Follow the steps 1) to 3) in the “CUSTOM Menu” section on page 23.
4
5
Enter your desired fourdigit password (except
for 4737)
1
2
3
4
5
6
7
8
9
6
Select “PARENTAL
LEVEL”
or
To exit
the menu
SETUP
or
ENTER
ENTER
ENTER
PARENTAL LEVEL
CHANGE
0
7
Select the
desired levels
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
ALL
PARENTAL menu
PARENTAL
PASSWORD
Please enter a 4-digit password.
Hint
CONTROL LEVELS
• ALL:
All parental locks are cancelled.
• Levels 8:
DVD softwares of any grades (adult/general/children)
can be played back.
• Levels 7 to 2:
Only DVD softwares intended for general use and children can be played back.
• Level 1:
Only DVD softwares intended for children can be played
back, with those intended for adult and general use prohibited.
or
If you have set a password already,
enter the current four-digit
password.
PARENTAL
PASSWORD
Enter current password.
To Chang e the Pass w or d f or Parental Controls
You can change your password for parental controls. Follow the steps 1) to 3) in the “CUSTOM Menu” section on page 23.
DVD Functions
4
5
Enter your desired fourdigit password (except
for 4737)
1
2
3
4
5
6
7
8
9
6
Select “CHANGE”
7
Enter your new
four-digit password
(except for 4737)
To exit
the menu
SETUP
or
ENTER
PARENTAL LEVEL
CHANGE
0
1
2
3
4
5
6
7
8
9
ENTER
ALL
0
Hint
PARENTAL menu
SETUP
PARENTAL
PASSWORD
Please enter a 4-digit password.
PARENTAL
PASSWORD
Enter current password.
• Record the password in
case you forget it.
• If you forget the password,
press 4, 7, 3, 7 at step 4,
then enter your new password.
• Password will be cleared
and parental levels will be
set to ALL.
To return the All Selections of SET UP (except for PARENTAL) to the Default Setting
2
1
4
3
or
or
To exit
the menu
SETUP
STOP
SETUP
<SETUP MENU>
Select INITIALIZE
QUICK SETUP
QUICK SETUP
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
DTS
ENTER
ENGLISH
4:3 LETTER BOX
BITSTREAM
OFF
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
DTS
INITIALIZE
ENGLISH
4:3 LETTER BOX
BITSTREAM
OFF
Initialize?
NO
YES
– 26 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
Select “YES”
ENTER
x2
(twice)
Hint
• When you cancel
to initialize at step
3,select “NO”.
EN
Information
Language List
Language
Code
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
Language
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Code
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
Language
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Code
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
Language
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Information
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 22. If you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
– 27 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Specifications
[DVD section]
PRODUCT TYPE
DVD Player with Video Cassette recorder
CONNECTIONS
Front panel:
Video input
Audio input
Rear panel:
AUDIO input
VIDEO input
AUDIO output
VIDEO output
S-Video output
Analog audio output
RCA connector [ 1
RCA connector [ 2
RCA connector (left, right)
RCA connector
RCA connector (left, right)
RCA connector
Mini DIN 4-pin jack (75 Ω)
RCA connectors [ 2 (one left
channel, one right channel)
2 Vrms (47 kΩ)
Coaxial digital audio output One pin jack, 500mVpp (75 Ω)
Component output
Y output level: 1Vp-p (75Ω)
CB/PB output level: 0.7Vp-p (75Ω)
CR/PR output level: 0.7Vp-p (75Ω)
[VCR section]
NUMBER OF VIDEO HEADS
4
VIDEO SIGNAL STANDARD
NTSC color system
AUDIO RECORDING SYSTEM
1 Stationary head for liner audio
2 Rotary heads for Hi-Fi stereo
WOW AND FLUTTER
Below the measurement limitation (±0.001% W PEAK)
(JEITA)
CHANNEL COVERAGE
VHF
2-13
UHF
14-69
CATV
1-125
TIMER BACKUP
30 seconds
DISCS (PLAYBACK COMPATIBILITY)
DVD Video, Audio CD, CD-RW/R
DVD-RW/R, DVD+RW/R
FREQUENCY RESPONSE
DVD (linear sound) : 20 Hz to 20 kHz (sample rate: 48 kHz)
20 Hz to 44 kHz (sample rate: 96 kHz)
CD :
20 Hz to 20 kHz
SIGNAL-TO-NOISE RATIO (S/N RATIO)
CD :
110 dB (JEITA)
DYNAMIC RANGE
DVD (linear sound) : 90 dB
CD :
90 dB (JEITA)
TOTAL DISTORTION FACTOR
DVD :
1KHz
0.008% (JEITA)
CD :
1KHz
0.008% (JEITA)
POWER SOURCE
120V AC +/- 10%, 60Hz +/- 0.5%
POWER CONSUMPTION
21W (standby: 3.6W)
OPERATING TEMPERATURE
41°F (5°C) to 104°F (40°C)
DIMENSIONS
W: 17 3/16” (435 mm)
H: 3 3/4” (94 mm)
D: 9 3/16” (233 mm)
WEIGHT
Approx. 6 lbs (2.7 kg)
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will be English.
Information
Service Information (For the U.S.)
For the location of the nearest Sharp Authorized Service Center, or to obtain product literature, accessories,
supplies or customer assistance, please call 1-800-BE-SHARP (1-800-237-4277) or visit SHARP’s website
(http://www.sharpusa.com).
– 28 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Troubleshooting Guide
If this unit does not perform properly when operated as instructed in this Operation Manual, check this unit consulting the following checklist.
PROBLEM
D
V
D
V
C
R
No power.
V
C
R
Timer recording is impossible.
This unit does not respond to
the remote control.
Cannot go into Record mode.
Playback picture is partially
noisy.
Cannot view a tape but the
audio is OK.
No, or poor, playback picture.
TV programs cannot be seen
normally.
Video or color fades in and out when
making a copy of a video tape.
•
•
No picture.
– 29 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
EN
Information
• Connect the video cables firmly.
• Insert a correct video disc that plays on this unit.
• Press the DVD button on the remote control. Check if the DVD OUTPUT light is lit.
Then try other DVD features.
Disc cannot be played.
• Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fingerprints, scratches, or dusts
on its surface.
No sound.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output.
• Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.
Distorted picture.
• Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign
of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
• Check if the INTERLACE/PROGRESSIVE mode is set correctly according to your TV. See page 9.
• The selected language is not available for audio or subtitles on the DVD.
Audio or subtitle language
does not match the set up.
This is not a malfunction.
The camera angle cannot be • The DVD does not contain sequences recorded from different camera angles.
changed.
This is not a malfunction.
• The DVD does not contain audio source or subtitles in the selected language.
Audio or subtitle language
cannot be changed.
This is not a malfunction.
“Prohibited icon” appears on • That operation is prohibited by this unit or the disc. This is not a malfunction.
the screen, prohibiting an
operation.
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Operation
Manual for details on correct operations.
Playback from a desired track and random playback are not available during program playback.
Some functions are prohibited on some discs.
D
V
D
•
CORRECTIVE ACTION
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the
obstacles between the sensor and the remote.
• You have to be within 23 feet of this unit.
• Check if the right mode is selected. If it’s not in the right mode, press the DVD or VCR
buttons, whichever you need, on the remote control.
• Check if a cassette tape is in this unit.
• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then. If you hear some signal sound from the radio in response to your pressing buttons on the remote, the remote control is working.
• Make sure the timer recording is set correctly.
• Make sure the TIMER and
lights appear on the VCR/DVD. If not, press the SUBTITLE/T-SET button.
• Make sure the VCR clock is set correctly.
• Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Activate this unit in VCR mode. Press the VCR button on the remote control so that
the green VCR OUTPUT light is lit.
)
• Adjust tracking control for a better picture by pressing the CH (
buttons on the VCR/DVD or the SKIP/CH.(K/L) buttons on the remote control.
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the VCR is not in the Menu mode.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
• Re-check the ANT. IN and ANT. OUT connections. See pages 1 and 7.
• Press the VCR/TV button.
• Press the VCR button on the remote control to activate it in the VCR mode. Check if the green
VCR OUTPUT light is lit. Then, set it to the TV position by pressing the VCR/TV button.
• You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
Para futura referencia, anote los números de modelo y de serie (indicados en la parte posterior esta unidad) en el espacio provisto.
No. de modelo:
DV-NC150U
No. de serie:
AVISO: PARA REDUCIR EL RIESGO DE INCENDIO O ELECTROCHOQUE NO
EXPONGA ESTE APARATO A LA HUMEDAD.
PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, HAGA QUE LA
PALETA ANCHA DEL ENCHUFE COINCIDA CON LA RANURA ANCHA E
INTRODÚZCALA HASTA EL FONDO.
PRECAUCION
Este símbolo previene al usuario del voltaje
aislado dentro de la unidad que puede provocar
descargas eléctricas peligrosas.
PELIGRO DE DESCARGA ELECTRICA NO
ABRIR DECLARACIÓN DE CONFORMIDAD
PRECAUCION:
TPARA REDUCIR EL RIESGO DE DESCARGA ELECTRICA, NO QUITE LA CUBIERTA. EL USUARIO NO
DEBERA DAR NINGUN TIPO DE SERVICIO A NINGUNA PARTE INTERNA. DEBERA SER REALIZADO SOLO
POR PERSONAL DE SERVICIO CALIFICADO.
Este símbolo advierte al usuario que existen
instrucciones de operación y de mantenimiento en la literatura incluida en esta unidad.
“ADVERTENCIA—Las reglas de la FCC (Comisión Federal de Comunicaciones) estipulan que cualquier modificación o cambio a este equipo no aprobado expresamente por
el fabricante podrá anular la autorización del usuario para operar este equipo”.
Este dispositivo cumple con la Parte 15 de las reglas de la FCC (Comisión Federal de Comunicaciones). La operación
se encuentra sujeta a las dos condiciones siguientes:
(1) Este dispositivo no debería producir interferencias perjudiciales, y
(2) este dispositivo debe aceptar cualquier interferencia recibida, incluyendo las que puedan producir una operación indeseable.
INFORMACION
Este equipo se ha sometido a todo tipo de pruebas y cumple con las normas establecidas para dispositivo digital de
Clase B, de conformidad con la Parte 15 de las reglas de la FCC (Comisión Federal de Comunicaciones). Estas reglas
están diseñadas para asegurar una protección razonable contra interferencias perjudiciales en las instalaciones residenciales. Este equipo genera, utiliza y puede emitir energía de radiofrecuencia y, si no se instala y utiliza debidamente, es
decir, conforme a las instrucciones, podrían producirse interferencias perjudiciales en las radiocomunicaciones. Sin
embargo, no se garantiza que estas interferencias no se produzcan en una instalación determinada. Si este equipo ocasiona interferencias en la recepción de radio o televisión, lo cual puede comprobarse con sólo apagar y encender el
equipo, intente corregir el problema mediante una o una combinación de las siguientes medidas:
—Reoriente la antena receptora o cámbiela de lugar.
—Aumente la separación entre el equipo y el receptor.
—Enchufe el equipo a una toma de corriente situada en un circuito distinto del receptor.
—Consulte a su distribuidor o a un técnico experto en radio/televisión.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Este aparato digital de la Clase B cumple con la norma ICES-003 de Canadá.
Aviso al instalador del sistema CATV:
Este aviso tiene la finalidad de llamar la atención del instalador del sistema CATV para que tenga en cuenta el Artículo
820-40 de NEC, que ofrece instrucciones para realizar una conexión a tierra apropiada y, en particular, especifica que
el cable de puesta a tierra deberá conectarse al sistema de puesta a tierra del edificio tan cerca del punto de entrada del
cable como sea posible.
PRECAUCION:
Español
ESTA UNIDAD HA SIDO CLASIFICADA COMO PRODUCTO CLASS 1 LASER.
EL USO DE MANDOS O AJUSTES O LA REALIZACION DE PROCEDIMIENTOS DISTINTOS DE LOS INDICADOS EN LA PRESENTE IMPLICA EL RIESGO DE EXPOSICION A UNA RADIACION PELIGROSA.
COMO LOS RAYOS LASER UTILIZADOS EN ESTA UNIDAD PUEDEN RESULTAR PERJUDICIALES PARA SUS OJOS,
NO INTENTE DESARMAR EL GABINETE. SOLICITE EL SERVICIO UNICAMENTE A PERSONAL CUALIFICADO.
Los productos que han ganado la marca ENERGY STAR® han sido diseñados para proteger el medio ambiente mediante
una eficiencia superior en el uso de la energía.
– 30 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
ES
IMPORTANTES MEDIDAS DE SEGURIDAD Y PRECAUCIONES
vídeo, asegúrese de que la antena o el cableado tenga
conexión tierra para conseguir de esta manera una protección contra voltajes no deseados y cargas estáticas.
El artículo 810 del Código de Electricidad Nacional
ANSI/NFPA número 70, proporciona información acerca
de la manera adecuada de conexiones a tierra de la
estructura del mástil y la estructura soporte, sobre la
unidad del cable del interior de cobre de antena, tamaño
de los conductores tierra, ubicación de la unidad de
descarga de la antena, conexión a los electrodos tierra,
y requerimientos de los electrodos tierra (Fig. A).
FIGURA A
EJEMPLO DE CONEXIÓN A TIERRA DE ANTENA DE
ACUERDO CON EL CÓDIGO ELÉCTRICO NACIONAL.
ABRAZADERA
DE LA ANTENA.
UNIDAD PARA LA DESCARGA
DE LA ANTENA
(NEC SECCIÓN 810-20)
EQUIPO PARA EL
SERVICIO
ELÉCTRICO
CÓDIGO DE NEC NATIONAL ELECTRIC
S2898A
CONDUCTORES TIERRA
(NEC SECCIÓN 810-21)
ABRAZADERA A TIERRA.
SISTEMA DE ELECTRODOS PARA EL
SUMINISTRO DE TOMA A TIERRA
(NEC ARTÍCULO 250, PARTE H)
15) Líneas de alimentación - Un antena exterior no debe ser
instalada en la cercanía de líneas de alimentación aéreas
ni de otros circuitos de potencial para iluminación eléctrica,
o donde pueda caerse y hacer contacto con tales líneas o
circuitos. Al instalar un sistema de antena exterior, enta
mucho cuidado de no tocar tales líneas o circuitos de alimentación, ya que el contacto con ellos podría será fatal.
16) Sobrecarga - No sobrecargue los tomacorrientes
murales ni los cables de extensión, ya que esto podría
causar incendios o descargas eléctricas.
17) Sobrecarga - No sobrecargue las tomas murales, los cables
prolongadores ni los receptores integrales, ya que si lo hace
pueden producirse incendios o descargas eléctricas.
18) Entrada de objetos y líquidos - Nunca introduzca objetos de
ningún tipo por las aberturas de sete producto, ya que pordría tocar peligrosos puntos de alta tensión o cortocircuitar
partes, provocando incendios o descargas elécticas. Nunca
derrame ningún tipo de líquido sobre el producto.
19) Servicio - No intente reparar el producto usted mismo; al abrir
o desmontar las cobiertas usted se expondrá a alta tensión y
a otros peligros. Solicite todo servicio a personal calificado.
20) Daños que requieran reparación - En los siguientes
casos, desconecte el producto del tomacorriente mural y
llame a un técnico de servicio calificado:
a) Cuando el cable de alimentación o la clavija estén dañados,
b) Si se ha derramado líquido sobre la unidad, o si algún
objeto ha caído dentro del producto,
c) Si el producto ha sido expuesto a la lluvia o al agua,
d) Cuando a pesar de haber sebuido las instrucciones de
operación, el producto no funcione normalmente. Ajuste
solamente los controles mencionados en el manual de
instrucciones; el ajuste incorrecto de otros controles
podrá causar daños a la unidad, la que por lo general
requerirá de un prolongado trabajo de reparación (por un
técnico calificado) para que sus condiciones normales
de operación puedan ser restablecidas,
e) Si el producto se ha caído o si el gabinete se ha dañado.
f) Cuando el producto muestre un cambio notorio en su rendimiento.
21) Piezas de requesto - Cuando sea necesario reemplazar
piezas, asegúrese de que el técnico de servicio emplee las
piezas de requesto especificadas por el fabricante, o piezas
que tengan las mismas características que las piezas originales. Las sustituciones no autorizadas podrán causar
incendios, descargas eléctricas y otoros problemas.
22) Revisión de seguridad - Al finalizar cualquier servicio de mantenimiento o reparación de este producto, solicítele al técnico que
efectúe comprobaciones de seguridad para determinar si el producto se encuentra o no en condiciones óptimas de operación.
23) Calor - Este producto debe colocarse fuera del alcance
de fuentes de calor tales como radiadores, rejillas de
calefacción, estufas o cualquier otro producto destinado
a producir calor, incluyendo los amplificadores.
– 31 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
CABLE DE COBRE
PARA LA ANTENA.
ES
Español
1) Lea las instrucciones - Lea detenidamente todas las instrucciones de seguridad y operación antes de usar el producto.
2) Conserve las instrucciones - Conserve las instrucciones
de seguridad y operación para consultas futuras.
3) Respete las advertencias - Observe estrictamente todas
las advertencias impresas en el producto y las incluidas
en el manual de instrucciones.
4) Siga las instrucciones - Siga todas las instrucciones de operación.
5) Limpieza - Desconecte el producto del tomacorriente mural
antes de limpiarlo. No use limpiadores líquidos ni aerosol.
Use un paño húmedo para la limpieza del producto.
EXCEPCIÓN: A un producto que haya sido diseñado para
funcionar sin interrupción y que, por cualquier razón
específica, como puede ser la posibilidad de perder un
código de autorización para un convertidor de CATV, no
deba ser desenchufado por el usuario para su limpieza o
con otra finalidad, no se le aplicará lo indicado en la
descripción de limpieza del punto 5.
6) Enchufes - No use enchfes no recomendados por el fabricante del producto, ya que podría ser peligroso.
7) Agua y humedad - No use este producto cerca del agua,
por ejemplo, cerca de una bañera o lavamanos, cerca
del fregadero de la cocina o lavandería, en un piso mojado, cerca de una piscina, etc.
8) Accesorios - No instale este pro- ADVERTENCIA SOBRE EL USO
DE CARROS PORTÁTILES
ducto en un carro, soporte,
trípode o mesa inestables. El
grabador de videocassettes
podría caerse, causando serias
lesiones a un niño o adulto, resultando también severamente
dañado. Uselo sólo el un carro,
S3125A
soporte, trípode o mesa recomendados por el fabricante, o vendidos con el producto.Toda
instalación del producto deberán hacerse de acuerdo a
las instrucciones del fabricante, empleando los accesorios de instalación recomendados por el mismo.
9) La combinación de producto y carro debe ser movida con cuidado. Las detenciones bruscas, la fuerza excesiva y las superficies
disparejas podrán hacer que el producto y el carro se vuelquen.
10) Ventilación - El gabinete del producto tiene renuras y aberturas de ventilación que garantizan el funcionamiento confiable del producto, evitando que se recaliente. Estas aberturas no deberán ser bloquear las aberturas, nunca setúe
el grabador de videocassettes encima de una cama, sofá,
alfombra u otra superficie similar. El grabador de videocassettes no debe ser instalado en un mueble emportado,
como una repisa para libros o bastidor, a menos que se
pueda garantizar una ventilación adecuada, o cuando las
instrucciones del fabricante así lo especifiquen.
11) Alimentación - Este grabador de videocassettes sólo
debe ser operado mediante el tipo de fuente de alimentación especificado en la etiqueta indicadora. Si no
seta seturo del tipo de fuente de alimentación que tiene en
su casa, consulte a su distribuidor o a la compañía de
electricidad local En el caso de grabador de doseñados
para funcionar a pilas o con otras fuentes de alimentación,
consulte el manuel de instrucciones respectivo.
12) Conexión a tierra o polarización - Este producto está equipado con una clavija polarizada de corriente alterna (una clavija que tiene una espiga más ancha que la otra). Esta clavija
solamente pordá ser insertada en el tomacorriente en una
sola dirección. Esta es una medida de seguridad. Si no
puediera insertar completamente la clavija en el tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera
posible insertar la clavija, tome contacto con un electricista
para que repare su tomacorriente obsoleto . No modifique
las características de seguridad de la clavija polarizada.
13) Protección del cable de alimentación - Los cables de alimentación deberán ser tendidos de manera tal que la probabilidad de que sean pisados o aplastados por otros objetos sea
mínima. Preste especial atención a las clavijas de los cables, a
los receptáculos, y al punto por donde salen del producto.
14) Conexión Tierra de una Antena Exterior: Si una antena
exterior o sistema de cable es conectado al aparato de
Español
Conexiones
Activación de la unidad por primera vez
Consulte la "Conexión básica del televisor" en la
página delantera antes de utilizar esta unidad.
VCR
VCR
1
Canal de salida RF
Si el canal 3 se está utilizando para una transmisión.
1)Programe su televisor al canal 4.
2)Inserte una cinta pregrabada en esta unidad.
3)Pulse el botón OUTPUT en el VCR/DVD para que
se encienda la luz VCR OUTPUT.
• Si no se enciende la luz ”VCR” en la pantalla de
esta unidad, pulse el botón VCR/TV en el mando a
distancia.
4)Pulse una vez el botón PLAY.
5)Después de unos segundos, pulse el botón PLAY
en el VCR/DVD durante 3 segundos.
• El canal de salida RF cambiará del canal 3 al canal
4 y podrá ver una imagen reproducida.
• Cuando no aparezca una imagen en la pantalla del
televisor, repita el paso 4.
6)Pulse el botón STOP para parar la reproducción.
Encienda el televisor y sintonice al canal 3.
• Si el canal 3 se está utilizando para una transmisión, vea la sección "Canal de salida RF".
2
POWER
Mando a distancia
Pantalla del televisor
SELEC. IDIOMA
ENGLISH
FRANCAIS
o
B ESPAÑOL
3
[ON]
CA 01
Instalación de las pilas del mando a distancia
AJUSTE AUTO
1
2
3
Conecta el cable de la caja de canales de cable o la caja
de satélite en la toma ANT IN de VCR/DVD?
SI
Si
Conmutación VCR/DVD
POWER
NO
OPEN/CLOSE
POWER SPEED
No
AUDIO
Espere unos minutos.
Después del escaneo
AV IN 2
VIDEO
Pulse el botón
MENU para salir.
L(MONO)-AUDIO-R
REW
FF
STOP/
EJECT
OUTPUT
PLAY
CH
REC TIMER
VCR
DVD
STOP
PLAY
DVD
( TRACKING )
1
2
3
4
5
6
SKIP/CH.
VCR/TV
Botón VCR
8
9
0
+10
VCR
DVD
• El sintonizador se detiene en el canal memorizado más
abajo.
• Puede seleccionar sólo los canales memorizados en esta
unidad con los botones SKIP/CH (K/L).
• Si aparece de nuevo "AJUSTE AUTO" en la pantalla del
televisor, compruebe las conexiones de los cables y luego
pulse otra vez el botón B.
SLOW
PAUSE
Botón DVD
OUTPUT
VCR
7
DISPLAY
PLAY
DVD
STOP
Luz
DVD OUTPUT
REC/OTR
MENU
ENTER
RETURN
SETUP TOP MENU
Botón OUTPUT
MODE
ZOOM
SEARCH CLEAR/
MODE C.RESET
SUBTITLE ANGLE REPEAT
A-B
T-SET
Luz
VCR OUTPUT
VCR / DVD COMBINATION
MODO VCR
Pulse el botón VCR en el mando a distancia.
(Compruebe que está encendida la luz VCR OUTPUT.)
MODO DVD
Español
Pulse el botón DVD en el mando a distancia
(Compruebe que está encendida la luz DVD OUTPUT.)
Consejo
• Si pulsa sólo el botón OUTPUT en el panel frontal NO
conmuta el modo del mando a distancia. DEBE seleccionar también el modo correcto en el mando a distancia.
– 32 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
ES
Español
Ajuste del reloj
Reproducción de la grabadora de vídeo
VCR
Antes: Encienda el televisor y cambie al canal 3.
VCR
1
-MENUPROGRAMAR
AUTOREPETIR [OFF]
AJUSTE CANAL
B AJUSTE DE RELOJ
SELEC. IDIOMA
SALIDA DEL AUDIO
TV ESTEREO [ON]
SAP
MENU
• Si el canal 3 se está utilizando para una transmisión, vea la sección "Canal de salida RF".
VCR
VCR
1
2
Mando a distancia
• Si no se ha ajustado el reloj, aparece la pantalla AJUSTE DE RELOJ cuando pulse el
botón MENU. En este caso, vaya al paso (2).
o
REPRODUCIR B
PLAY
3
Pantalla del televisor
4
[VCR/DVD]
PARAR
STOP
EXPULSAR A
STOP/EJECT
/
2
AJUSTE DE RELOJ
o
MES
DIA
03 / ––
HORA MINUTO
–– : ––
AÑO
––––
AM/PM
––
VCR TV
7
8
9
0
+10
DISPLAY
VCR
DVD
SLOW
Seleccione el mes actual
3
AJUSTE DE RELOJ
o
MES
DIA
03 / 15
HORA MINUTO
–– : ––
o
HORA MINUTO
–– : ––
REW
STOP/
EJECT
FF
PLAY
REC TIMER
AÑO
2004
Reproducción de DVD/CD
Antes: Encienda el televisor, amplificador y otros equipos
que puedan estar conectados a esta unidad. Asegúrese que
el televisor y el sintoamplificador de audio (de venta en los
comercios) están en el canal correcto.
AM/PM
––
DVD
DVD-V
DVD-V
1
VR mode
CD
2
[VCR/DVD]
POWER
OPEN/CLOSE
MES
DIA
AÑO
0 3 / 1 5 LUN 2 0 0 4
HORA MINUTO
05 : ––
AM/PM
––
3
Mando a distancia
4
Pantalla del televisor
STOP
PLAY
Seleccione la hora actual
5
6
L(MONO)-AUDIO-R
2
AJUSTE DE RELOJ
o
AV IN 2
VIDEO
REC OTR
Seleccione el año actual
5
3
4
PLAY
STOP
AM/PM
––
AJUSTE DE RELOJ
MES
DIA
03 / 15
POWER
AÑO
––––
Seleccione el día actual
4
2
3
1
PAUSE
[VCR/DVD]
OPEN/CLOSE
AJUSTE DE RELOJ
o
MES
DIA
AÑO
0 3 / 1 5 LUN 2 0 0 4
HORA MINUTO
05 : 40
AM/PM
––
Seleccione los minutos actuales
1
POWER SPEED
2
AUDIO
1
2
3
4
5
6
SKIP CH.
VCR TV
8
9
SLOW
7
DISPLAY
0
+10
VCR
DVD
AJUSTE DE RELOJ
o
MES
DIA
AÑO
0 3 / 1 5 LUN 2 0 0 4
HORA MINUTO
05 : 40
AM/PM
P M AM
B PM
3
4
PAUSE
1
5
OPEN/CLOSE
OUTPUT
CH
VCR
DVD
STOP
PLAY
DVD
( TRACKING )
PLAY
STOP
4
3
Español
7
Seleccione "AM" o "PM".
8
Para salir de la pantalla AJUSTE DE RELOJ.
– 33 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
ES
Español
Mando a distancia
Modo DVD
Disco/cinta
Botón
(Orden alfabético)
POWER SPEED
1
1
2
3
4
5
6
7
8
9
0
+10
3
SKIP CH.
4
5
6
7
8
9
0
+10
DISPLAY
VCR
DVD
Modo de grabadora de vídeo
CD
MP3
ENTER
VCR
• Para seleccionar directamente • Para seleccionar directamente • Para seleccionar el canal
• El botón +10 no tiene efecto en el
el capítulo o el título
la canción
modo de grabadora de vídeo
• Para buscar en avance/retroceso
en un disco
• Para buscar en avance/
• Para empezar la reproducción en avance/ retroceso en un disco
retroceso lento durante el modo de pausa
AUDIO
2
DVD-V
• Para mover el cursor y
determinar su posición
• Para mover el curso y
determinar su posición
VCR TV
• Para el avance/retroceso
de una cinta
• Para seleccionar un ítem en el
menú de la grabadora de vídeo
• Para avanzar al siguiente menú de
la grabadora de vídeo
• Para volver un paso durante el ajuste
del reloj y temporizador
SLOW
A-B
PAUSE
ANGLE
PLAY
AUDIO
STOP
• Para repetir entre los puntos • Para repetir entre los puntos
A y B elegidos
A y B elegidos (CD)
• Para seleccionar los ángulos
de la cámara en un disco
• Para seleccionar el idioma de • Para seleccionar ESTÉREO,
audio en un disco
L-CH o R-CH (CD)
REC OTR
MENU
ENTER
ZOOM
• Para borrar los marcadores
• Para borrar los números
entrados incorrectamente
• Para borrar los marcadores
(CD)
• Para salir del menú de la grabadora
• Para retirar el número de estado de vídeo
en la entrada de programa
• Para reponer el contador de cinta
• Para borrar los números
entrados incorrectamente
DISPLAY
• Para indicar el modo de
disco actual
• Para indicar el modo de
disco actual
• Para seleccionar el modo
de salida de DVD
• Para activar el mando a
distancia en el modo DVD
• Para seleccionar el modo de
salida de DVD
• Para activar el mando a
distancia en el modo DVD
• Para llamar el menu en un
disco
• Para llamar el menú MP3
(MP3)
• Para activar/desactivar el
nivel del negro
• Para activar/desactivar el
envolvente virtual
• Para activar/desactivar el
reproducción rápìdo
• Para disponer el orden de
reproducción o la
reproducción aleatoria
• Para activar/desactivar el
envolvente virtual
RETURN
SETUP TOP MENU
MODE
CLEAR/
C.RESET
SEARCH CLEAR
MODE C.RESET
SUBTITLE ANGLE REPEAT
A-B
T-SET
VCR / DVD COMBINATION
DVD
MENU
MODE
PAUSE
PLAY
POWER
RETURN
SEARCH
MODE
SETUP
SKIP/CH.
SKIP/CH.
• Para llamar el menú de la
grabadora de vídeo
• Para hacer una pausa de
• Para hacer una pausa en la
reproducción del disco
• Para avanzar la reproducción reproducción del disco
un cuadro a la vez
• Para hacer una pausa de la
reproducción o grabación de la cinta
• Para avanzar la reproducción
un cuadro a la vez
• Para empezar la reproducción • Para empezar la reproducción • Para empezar la reproducción
del disco
del disco
de la cinta
• Para activar o desactivar la
unidad
• Para activar o desactivar la
unidad
• Para activar o desactivar la
unidad
• Para empezar una grabaciòn o una
grabaciòn de Vn-Toque
REC/OTR
REPEAT
• Para indicar la hora actual,
contador de cinta y canal
• Para reproducir repetidamente una
• Para reproducir repetidamente canción o disco (CD)
• Para reproducir repetidamente una
un capítulo o título
canción, grupo o disco (MP3)
• Para volver a la operación
• Para volver a la operación
previa en el menú de
previa en el menú de
programación de DVD
programación de DVD
• Para buscar una canción
• Para buscar un capítulo, título u hora • Para buscar la hora (CD)
• Para llamar el menú de
• Para volver rápidamente a un
• Para volver rápidamente a
búsqueda de índice u hora
lugar o disco
un lugar o disco
• Buscar los marcadores
• Buscar los marcadores (CD)
• Para llamar el menú de
programación de DVD
• Para llamar el menú de
programación de DVD
• Para saltar capítulos
• Para saltar canciones
• Para cambiar de canal
• Para ajustar manualmente el
seguimiento durante la reproducción
SLOW
• Para ver la cinta en cámara
lenta
SPEED
• Para seleccionar la velocidad
de grabación
STOP
SUBTITLE
T-SET
Español
TOP MENU
• Para parar la grabación
• Para llamar el menú superior
en un disco
ZOOM
• Para volver al archivo superior
de la jerarquía más alta en el
programa y menú MP3 (MP3)
• Para seleccionar el modo de
salida de la grabadora de vídeo
• Para activar el mando a distancia
en el modo de la grabadora de vídeo
• Para seleccionar la posición
de DVD o posición del televisor
• Para seleccionar la posición de
• Para seleccionar la posición de la
CD/MP3 o la posición del televisor grabadora de vídeo o posición del televisor
• Para ampliar parte de la
imagen (x2/x4)
– 34 –
Downloaded From DvDPlayer-Manual.com Sharp Manuals
• Para parar la reproducción o
grabación
• Para poner la grabadora de
vídeo en el modo de espera
para una grabación con temporizador
• Para seleccionar subtítulos
en un disco
VCR
VCR/TV
• Para parar la grabación
ES
CONSUMER LIMITED WARRANTY
(Valid for warranty service in the U.S. only)
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it
will, at its option, either repair the defect or replace the defective Product or part thereof with a new or
remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth
below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper
voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or
construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and
provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of
Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to
the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which
were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not
allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description: DV-NC150U VCR/DVD Combination
(Be sure to have this information available when you need service
for your Product.)
Warranty Period for this Product:
One (1) year parts and ninety (90) days labor from date of purchase.
Additional Item(s) Excluded from warranty
Coverage (if any):
Non-rechargeable batteries.
Where to Obtain Service:
Call Sharp Electronics corporation toll free at 1-800-BE-SHARP for
instructions on how to obtain service on your VCR/DVD combination.
What to do to Obtain Service:
Ship your product, prepaid, as per the instruction given by the Sharp
representative at the toll free number (1-800-BE-SHARP). BE sure to
have your proof of purchase available. Be sure to ship the product
securely packaged and insured against shipping damage.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, GO TO OUR WEBSITE AT www.sharpusa.com
OR CALL 1-800-BE-SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
Osaka, Japan
9HS1VMN20342
H9641UD★★★★
1VMN20342
Downloaded From DvDPlayer-Manual.com Sharp Manuals
Printed in China