Yamaha RX-485 Owner's manual

Add to my manuals
20 Pages

advertisement

Yamaha RX-485 Owner's manual | Manualzz
RX-485/385
Natural Sound Stereo Receiver
65W + 65W (8Ω) RMS Output Power, 0.04% THD, 20 – 20,000 Hz (RX-485)
45W + 45W (8Ω) RMS Output Power, 0.04% THD, 20 – 20,000 Hz (RX-385)
High Dynamic Power, Low Impedance Drive Capability
Continuously Variable Loudness Control
40-Station Random Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability
IF Count Direct PLL Synthesizer Tuning System
Remote Control Capability
Pure Direct Switch to Reproduce the Purest Source Sound (RX-485 Only)
Thank you for selecting this YAMAHA stereo receiver.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
OWNER’S MANUAL
CONTENTS
IMPORTANT!
Please record the serial number of this
unit in the space below.
• Explanation of Graphical Symbols
Safety Instructions ...................2
Supplied Accessories ..............4
Connections.............................5
Operations ...............................9
Tuning Operations ..................12
Preset Tuning .........................13
Remote Control Transmitter ...16
Notes about the Remote
Control Transmitter ................17
Troubleshooting ......................18
Specifications .........................19
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
SAFETY INSTRUCTIONS (U.S.A.)
1
2
3
4
5
6
6A
7
8
9
10
11
12
13
14
15
A.
B.
C.
D.
E.
2
Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
Follow Instructions – All operating and other instructions
should be followed.
Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
A unit and cart combination should
be moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the unit and
cart combination to overturn.
Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
Ventilation – The unit should be situated so that its location
or position does not interfere with its proper ventilation.
For example, the unit should not be situated on a bed,
sofa, rug, or similar surface, that may block the ventilation
openings; or placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air
through the ventilation openings.
Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce
heat.
Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
The power-supply cord or the plug has been damaged;
or
Objects have fallen, or liquid has been spilled into the unit;
or
The unit has been exposed to rain; or
The unit does not appear to operate normally or exhibits a
marked change in performance; or
The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
17
18
19
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
Power Lines – An outdoor antenna should be located away
from power lines.
Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
LEAD IN
WIRE
MAST
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
Note to CATV system installer (U.S.A.):
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close
to the point of cable entry as practical.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1
2
3
4
5
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical
shock, do not expose the unit to rain or water.
Never open the cabinet. If something drops into the set,
contact your dealer.
Do not use force on switches, controls or connection
wires. When moving the unit, first disconnect the power
plug and the wires connected to other equipment. Never
pull the wires themselves.
The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the
temperature inside the cabinet will rise rapidly and
eventually damage the circuits. Therefore, avoid placing
objects against these openings and do not install the unit
where the flow of air through the ventilation openings
could be impeded.
6
7
8
9
10
11
12
Always set the VOLUME control to “– ∞” before starting
the audio source play. Increase the volume gradually to
an appropriate level after playback has been started.
Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding
that the unit is faulty.
When not planning to use this unit for long periods of
time (ie., vacation, etc.), disconnect the AC power plug
from the wall outlet.
To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is
not defeated.
AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime (U.S.A.)
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you to
avoid prolonged exposure from excessive
volume levels.
3
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or
87/308/EEC.
The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus
itself is turned off.
For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3
pin plug fitted. For details, refer to the instructions described below.
Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wire in the mains lead are coloured in accordance with the following code:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug. Proceed as follows: the wire which is coloured BLUE must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked
with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
Indoor FM Antenna
Remote Control Transmitter
RX-485
AM Loop Antenna
4
Batteries (size AA, R6, UM-3)
RX-385
CONNECTIONS
ANTENNA CONNECTIONS
●
●
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Outdoor FM antenna
Indoor FM
antenna
(included)
Outdoor AM antenna
AM loop
antenna
(included)
300-ohm
feeder
FM 75Ω
ANT UNBAL
GND
AM
ANT
75-ohm
coaxial cable
75-ohm/300-ohm
antenna adapter
PHONO
CD
AUX
TAPE
PB
Ground
Connecting the AM loop antenna
➀
Orient so that the best
reception is obtained.
➂
➁
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
When connecting the indoor
FM antenna, make sure that
the grooved part of the
connector hole is facing
downward.
● If you need an outdoor
FM antenna to improve
FM reception quality, either 300-ohm feeder or coaxial cable
may be used. In locations troubled by electrical
interference, coaxial cable is preferable.
●
5
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
AUDIO CONNECTIONS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
RX-485
Speakers A
Video cassette player etc.
Tape deck 2
Left
AUDIO OUT
LINE OUT
LINE IN
Right
(U.S.A. model)
FM 75Ω
ANT UNBAL
GND
GND
REMOTE
CONTR0L
AC OUTLETS
SPEAKERS
R
AM
ANT
A
A
B
B
PHONO
L
R
PHONO
CD
AUX
TAPE 1
TAPE
REC
PB
OUT
SWITCHED
L
120V 50Hz
100W MAX TOTAL
TAPE 2
TAPE
REC
PB
OUT
To AC outlet
Turntable
Compact disc player
LINE IN
LINE OUT
OUTPUT
GND
OUTPUT
REMOTE CONTROL
Right
Speakers B
Tape deck 1
*
6
Left
: Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
RX-385
Speakers A
Video cassette player etc.
Left
AUDIO OUT
Right
(U.S.A. model)
FM 75Ω
ANT UNBAL
GND
AC OUTLETS
SPEAKERS
R
AM
ANT
SWITCHED
L
A
A
B
B
L
GND
R
PHONO
CD
AUX
120V 50Hz
100W MAX TOTAL
TAPE 1
TAPE
REC
PB
OUT
Turntable
Compact disc player
LINE IN
LINE OUT
OUTPUT
GND
OUTPUT
To AC outlet
Right
Tape deck
Left
Speakers B
*
: Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
7
CONNECTING SPEAKERS
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut to be as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
● One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
● Use speakers with the specified impedance shown on the
rear of this unit.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
➀ Press up the tab.
➁ Insert the bare wire.
➂
➁
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂ Press down the tab and
secure the wire.
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S)
(U.S.A., Canada and General models)
............................................................2 SWITCHED OUTLETS
(Australia and U.K. models)...................1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
8
REMOTE CONTROL (PHONO) connector
RX-485 only
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector by using the cable provided
with the turntable. This connection allows you to control the
turntable from the
provid
OPERATIONS
3
2
1, 6
7
4
TO PLAY A SOURCE
1
4
VOLUME
Select the speakers to be used.
SPEAKERS
A
B
ON
ON
OFF
OFF
0
— dB
* If you use two speaker systems, press both the A and B
switches.
∞” position.
Set to the “
2
5
POWER
6
3
Play the source. (For detailed information on the tuning
operations, refer to the page 12.)
VOLUME
Select a desired input source.
RX-485
MONITOR
TAPE 2
TAPE 1
INPUT
AUX
CD
TUNER
PHONO
0
— dB
COPY
Adjust to the desired output level.
RX-385
TAPE
MONITOR
INPUT
AUX
TUNER
CD
PHONO
* The name of the selected input source will appear in the
display.
* Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
7
If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (Refer to page 11.)
Notes
RX-485 only
●
If you select AUX, TUNER, CD or PHONO, be sure that
TAPE 1 and/or TAPE 2 are not being selected.
●
If you select TAPE 1 and TAPE 2 at the same time, the
result will be the sound from the tape deck 1.
●
For TAPE 1 and TAPE 2, whenever the button is pressed,
the corresponding input source is selected or canceled
alternately.
RX-385 only
●
If both TAPE MONITOR and another input selector button
are selected, TAPE MONITOR has priority.
9
1, 4
2
TO RECORD A SOURCE TO TAPE
RX-485
1
TO RECORD A SOURCE TO TAPE
RX-385
1
Select the source to be recorded.
MONITOR
TAPE 2
TAPE 1
INPUT
AUX
TUNER
CD
Select the source to be recorded.
TAPE
MONITOR
PHONO
INPUT
AUX
TUNER
CD
PHONO
COPY
* To dub from tape to tape, refer to the “Notes” shown
below.
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE 1 and/or TAPE 2 are not also selected.
2
3
4
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 12.)
Begin recording on the tape deck.
MONITOR
TAPE 1
2
3
4
To monitor the audio signals being recorded, press the
input selector button for the tape deck being used to
make the recording.
TAPE 2
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE MONITOR is not also selected.
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 12.)
Begin recording on the tape deck.
To monitor the audio signals being recorded, press the
TAPE MONITOR.
TAPE
MONITOR
INPUT
AUX
TUNER
CD
PHONO
INPUT
AUX
TUNER
CD
PHONO
COPY
Note
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being recorded.
Notes
● VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being
recorded.
● To dub from tape to tape, only the following method of
dubbing can be performed.
RECORDER
SOURCE
Tape deck connected to
the TAPE 2 terminals.
10
→
Tape deck connected to
the TAPE 1 terminals.
Adjusting the BALANCE control
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Selecting the SPEAKER system
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
BALANCE
SPEAKERS
0
L5
5R
Adjusting the BASS and TREBLE
controls
—
5
BASS
TREBLE
DEFEAT
DEFEAT
—
5+
5
5+
A
B
ON
ON
OFF
OFF
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
1
LOUDNESS
FLAT
— 30dB
I0
BASS
: Turn this clockwise to increase (or counterclockwise to decrease) the low frequency
response.
Set to the “FLAT” position.
2
VOLUME
TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency
response.
Set to the loudest listening level that
you would listen to.
0
— dB
3
LOUDNESS
FLAT
— 30dB
I0
Using the PURE DIRECT switch
RX-485 only
You can enjoy the purest possible sound from your audio
sources by setting this switch ON. By doing so, the audio
signal bypasses the BASS, TREBLE, BALANCE and
LOUDNESS controls, eliminating any alterations to the audio
signal.
Turn so that the desired volume can
be achieved.
When you listen with headphones
Connect the headphones to the PHONES jack. When listening
with headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
PHONES
PURE DIRECT
11
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
3
2
1
AUTOMATIC TUNING
1
MANUAL TUNING
Select the reception band (FM or AM) while watching
the display.
1
FM/AM
FM/AM
or
FM
2
Select the reception band (FM or AM) while watching
the display.
AM
2
TUNING
MODE
“AUTO TUNING”
goes off.
AUTO/MAN’L MONO
DOWN
TUNING
3
UP
Tune to a desired station manually.
DOWN
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stopped is not the
desired one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
➀
➁
STEREO
FM
12
MHz
0
20 40 60
l00
➂
TUNING
UP
* To continue tuning search, press and hold the button.
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
➀
➁
Display information
AM
TUNING
MODE
AUTO TUNING
AUTO/MAN’L MONO
3
or
FM
➂
Displays the band and frequency of the received station.
Illuminates when an FM stereo broadcast is received in
stereo.
Indicates the signal level of the received station.
PRESET TUNING
MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only
selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored.
3, 1
2, 5
4, 2
To store stations
1
To recall a preset station
Tune to a desired station.
(Refer to the previous page for tuning procedures.)
1
Select the page where the preset station is stored.
A/B/C/D/E
PRESET
2
FM
MEMORY
PRESET
MEMORY
FM
MEMORY
2
MAN’L/AUTO FM
Flashes on and off
for about 5
3
DOWN
PRESET
STATIONS
UP
Select a desired page (A – E) of preset stations while
watching the display.
A/B/C/D/E
Select the preset station number.
PRESET
FM
MEMORY
4
Select a preset station number (1–8) while watching the
display before “MEMORY” goes off from the display.
DOWN
5
MEMORY
PRESET
STATIONS
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If so,
it can be re-programmed by simply following the PRESET
TUNING steps.
UP
PRESET
STEREO
FM
MHz
0
20 40 60
Notes
● A new setting can be programmed in place of the former
one.
● For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
l00
AUTO TUNING
MAN’L/AUTO FM
Shows the displayd station
has been programmed to A1.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations on other pages in the
same way by selecting other pages in step 3.
13
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 13.
2
1
To store stations
1
When the automatic preset tuning is finished
FM/AM
FM
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 13.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 13.
2
MEMORY
MAN’L/AUTO FM
Press and
hold for about
3 seconds.
PRESET
and
AUTO TUNING
MEMORY
Flashes.
Flashes.
After 5 seconds, the automatic preset tuning begins from A1.
Received stations are programmed to A1, A2 ... A8
sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the received first station to
C5, select “C5” by using the A/B/C/D/E button and the
PRESET STATIONS button soon after the display begins
flashing on/off in step 2. After a few seconds, the automatic
preset tuning begins. The received first station is stored to C5,
and next stations to C6, C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
14
Notes
● You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 13.
● If the number of received stations is not enough to be stored
up to E8, the search is finished automatically when it
reaches the highest frequency after searching through all
frequencies.
● With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is week in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 13.
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations each other by easy operations.
2, 4
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1
2
Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 13).
4
EDIT
EDIT
Flashes
3
Next, recall the preset station on A5 by following the
same method with step 1.
Shows the exchange of stations is completed.
Flashes
15
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the
CD player, turntable and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also
control various functions of each component.
KEY FUNCTIONS
For Control of This Unit
POWER
SLEEP
PLAY/CUT
PHONO
PLAY
CD
Turns the power on/off.
SKIP
SEARCH
Selects preset station number
+ : Selects higher preset station number.
– : Selects lower preset station number.
A/B/C/D/E: Selects the page (A – E) of
preset stations.
— PRESET
DIR A
The power to the receiver is automatically
turned off one hour after this key is
pressed (so that “SLEEP” illuminates on
the display).
PAUSE/STOP DISC SKIP
+
DECK A/B
A/B/C/D/E TUNER
DIR B
TAPE 1
Selects input source.
PLAY
REC/PAUSE
STOP
TAPE 2
REC MUTE
AUX
—
+
VOLUME
Turns the volume level up/down.
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the
same. On each key function, refer to the corresponding instruction on your component’s manual.
Starts/stops record play on turntable.
POWER
SLEEP
SKIP
SEARCH
— PRESET
DIR A
PLAY/CUT
PHONO
PLAY
CD
PAUSE/STOP DISC SKIP
+
DECK A/B
A/B/C/D/E TUNER
DIR B
PLAY
REC/PAUSE
Controls compact disc player.
* DISC SKIP is applicable only to
compact disc changer.
STOP
TAPE 1
TAPE 2
REC MUTE
AUX
—
Controls tape deck.
* DIR A, B and DECK A/B are
applicable only to double
cassette tape deck.
* For a single cassette deck with
automatic reverse function,
pressing DIR A will reverse the
direction of tape running.
+
VOLUME
Illustrations : RX-485
* PLAY/CUT is equipped only on RX-485.
* TAPE 1 and TAPE 2 are equipped only on RX-485. On RX-385, they are replaced by TAPE only.
16
STANDBY mode (Europe model only)
While the power is on, pressing the POWER key on the remote
control transmitter switches the unit to the STANDBY mode.
(In this mode, the standby indicator on the front panel is half
illuminated.)
STANDBY mode
POWER on mode
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Remote control transmitter operation range
2
1
Remote control
sensor
3
Within approximately
7 m (23 feet)
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
● Use only AA, R6, UM-3 batteries for replacement.
● Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
● Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
● If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
30°
30°
Notes
● There should be no large obstacles between the remote
control transmitter and the main unit.
● If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
17
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
Amplifier
SYMPTOM
Firmly plug in the power cord.
No sound.
Incorrect output cord connections.
Connect the cords properly. If the problem persists,
the cords may be defective.
Appropriate input selector button is not pressed.
Press the appropriate input selector button
corresponding to the input source.
The sound suddenly goes off.
The protection circuit has activated because of
short circuit etc.
Turning the unit off and then on will reset the
protection circuit.
Only one side speaker outputs the sound.
Incorrect setting of the BALANCE control
Adjust it to the appropriate position.
Incorrect cord connection.
Connect the cord properly. If the problem persists,
the cables may be defective.
Incorrect cord connections.
Firmly connect the audio plugs. If the problem
persists, the cord may be defective.
No connection from the turntable to the GND
terminal.
Make the GND connection between the turntable
and this unit.
The volume level is low while playing a record.
The record is being played on a turntable with an
MC cartridge.
The player should be connected to the receiver
through the MC head amplifier.
The volume level cannot be increased, or
sound is distorted.
The power to the component connected to the REC
OUT terminals of this unit is off.
Turn the power to the component on.
FM stereo reception is noisy.
Because of the characteristics of FM stereo
broadcasts, this is limited to cases where the
transmitter is too far or the antenna input is poor.
Check the antenna connections.
Try using a multiple element FM antenna.
There is distortion and clear reception cannot
be obtained even with a good FM antenna.
There is multipath interference.
Adjust antenna placement to eliminate multipath
interference.
A desired station cannot be tuned in with Auto
tuning.
The station is too weak.
Use Manual tuning mode.
Use high quality directional FM antenna.
A desired station cannot be tuned in with Auto
tuning.
Weak signal or loose antenna connections.
Use Manual tuning mode.
There are continuous crackling and hissing
noises.
Noises will result from ligtning, fluorescent lamps,
motors, thermostats and other electrical equipment.
Use an outdoor antenna and a ground wire. This
will help somewhat but it is difficult to eliminate all
noises.
There are buzzing and whining noises
(especially in the evening).
A television set is being used nearby.
Relocate this unit away from the TV.
The remote control transmitter does not work.
Direct sunlight or lighting (of an inverter type of
flourescent lamp etc.) is striking the remote control
sensor of the main unit.
Change position of the main unit.
The batteries of this remote control transmitter are
too weak.
Replace the batteries with new ones.
The power to this unit is off.
Turn the power to this unit on.
FM
AM
Remote control
transmitter
Others
REMEDY
Power cord is not plugged in or is not completely
inserted.
Sound “hums”.
18
CAUSE
The unit fails to turn on when the POWER
switch is pressed.
The sound is degraded when monitoring is
performed by using the headphones connected
to the compact disc player or cassette deck
which are connected with this unit.
Tighten the AM loop antenna connections and
rotate it for best reception.
SPECIFICATIONS
AUDIO SECTION
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.04% THD
<RX-485> .....................................65W+65W
<RX-385>
[U.S.A. and Canada models].......45W+45W
[Australia, U.K., Europe and
General models]..........................40W+40W
6 ohms, 20 Hz to 20 kHz, 0.06% THD
<RX-485> .....................................70W+70W
<RX-385>
[U.S.A. and Canada models].......48W+48W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring
method)
<RX-485>
8/6/4/2 ohms ....................95/115/135/150W
<RX-385>
[U.S.A., Canada and General models]
8/6/4/2 ohms ..........................69/78/90/98W
[Australia, Europe and U.K. models]
8/6/4/2 ohms ..........................68/75/85/95W
DIN Standard Output Power per Channel
4 ohms, 1 kHz, 0.7% THD
[Europe model only]
<RX-485> ..............................................85W
<RX-385> ..............................................55W
IEC Power
<RX-485>
8 ohms, 1 kHz, 0.04% THD
[Europe model only]..............................75W
<RX-385>
8 ohms, 1 kHz, 0.04% THD
[Europe model only]..............................50W
Damping Factor
8 ohms, 20 Hz to 20 kHz ............................80
Input Sensitivity/Impedance
PHONO MM ......................2.5 mV/47 k-ohms
CD/TAPE/AUX ..................150 mV/47 k-ohms
Maximum Input Signal (1 kHz, 0.01% THD)
PHONO MM .........................................80 mV
Headphone Jack Rated Output/Impedance
8 ohms, 20 Hz to 20 kHz, 0.04% THD
Output Level
<RX-485> ............................................0.46V
<RX-385> ............................................0.45V
Impedance
<RX-485> ......................................390 ohms
<RX-385> ......................................330 ohms
Frequency Response (20 Hz to 20 kHz)
CD/TAPE/AUX..................................0±0.5 dB
RIAA Equalization Deviation
PHONO MM .....................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT (1V) ............0.02%
CD/TAPE/AUX to SP OUT
<RX-485>
(32.5W/8 ohms) ....................................0.02%
<RX-385>
(22.5W/8 ohms) ....................................0.02%
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted)........82 dB
CD/TAPE/AUX (Input Shorted) ...........105 dB
Residual Noise (IHF-A Network)............100 µV
Channel Separation (Vol. –30 dB)
PHONO MM (Input Shorted 1 kHz) .......60 dB
CD/TAPE/AUX
(Input 5.1 k-ohms Terminated 1 kHz)....60 dB
Tone Control Characteristics
BASS: Boost/cut .................±10 dB (50 Hz)
(Turnover frequency)
...........................................(350 Hz)
TREBLE: Boost/cut............±10 dB (20 kHz)
(Turnover frequency)
......................................(3.5 kHz)
Continuous Loudness Control
...............................................– 30 dB (1 kHz)
(Level related equalization)
FM SECTION
Tuning Range
[U.S.A., Canada and General models]
........................................87.5 to 107.9 MHz
[Australia, Europe, U.K. and General
models] ...........................87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF, 75 ohms)
[Except Europe model]
Mono...............................1.55 µV (15.1 dBf)
Stereo ................................21 µV (37.7 dBf)
Usable Sensitivity (75 ohms)
(30 dB S/N Quieting, 1 kHz, 100% mod.)
[Except Europe model]
............................................0.8 µV (9.3 dBf)
DIN, Mono (S/N 26 dB) [Europe model]
.............................................................0.9 µV
DIN, Stereo (S/N 46 dB) [Europe model]
..............................................................24 µV
Image Response Ratio
[Except Europe model] .......................45 dB
[Europe model] ...................................80 dB
IF Response Ratio ...................................80 dB
Spurious Response Ratio ........................70 dB
AM Suppression Ratio .............................55 dB
Capture Ratio..........................................1.5 dB
Alternate Channel Selectivity
[Except Europe model] .......................85 dB
Selectivity (two signals, 40 kHz Dev.)
[Europe model] ...................................70 dB
Signal-to-Noise Ratio
(IHF) Mono/Stereo
[Except Europe model] .............80 dB/75 dB
(DIN-Weighted, 40 kHz Dev.) Mono/Stereo
[Europe model] .........................74 dB/69 dB
Harmonic Distortion
Mono/Stereo (1 kHz)
[Except Europe model] ................0.1/0.2%
Mono/Stereo (40 kHz Dev.)
[Europe model] ............................0.1/0.2%
Stereo Separation (1 kHz) .......................50 dB
Frequency Response
30 Hz to 13 kHz...............................0 ±0.5 dB
20 Hz to 15 kHz...............................0 ±1.5 dB
AM SECTION
Tuning Range
[U.S.A., Canada and General models]
..........................................530 to 1,710 kHz
[Australia, U.K., Europe and General
models] .............................531 to 1,611 kHz
Usable Sensitivity ..............................100 µV/m
Selectivity.................................................32 dB
Signal-to-Noise Ratio ...............................50 dB
Image Response Ratio ............................40 dB
Spurious Response Ratio ........................50 dB
Harmonic Distortion...................................0.3%
AUDIO SECTION
Output Level/Impedance
FM (100% mod., 1 kHz)
[Except Europe model]
......................................500 mV/2.2 k-ohms
[Europe model (40 kHz Dev.)]
......................................400 mV/2.2 k-ohms
AM (30% mod., 400 Hz)
.........................................150 mV/2.2 k-ohms
GENERAL
Power Supply
[U.S.A. and Canada models]
...........................................AC 120V, 60 Hz
[Australia and U.K. models]
...........................................AC 240V, 50 Hz
[Europe model] ...................AC 230V, 50 Hz
[General model]
.................AC 110/120/220/240V, 50/60 Hz
Power Consumption
<RX-485>
[U.S.A. model].....................................155W
[Canada model].....................250 VA, 205W
[Europe, Australia and General models]
............................................................135W
<RX-385>
[Canada model] ..................................170W
[U.S.A., Australia, Europe, U.K. and
General models] .................................120W
AC Outlets
2 SWITCHED OUTLETS
[U.S.A., Canada, Europe and
General models].................100W max. total
1 SWITCHED OUTLET
[Australia and U.K. models]
...........................................100W max. total
Dimensions (W x H x D)
..........................................435 x 126 x 298 mm
(17-1/8” x 4-15/16” x 11-3/4”)
Weight
<RX-485> .....................7.0 kg (15 lbs. 6 oz.)
<RX-385> .....................6.1 kg (13 lbs. 7 oz.)
Accessories............................AM loop antenna
Indoor FM antenna
Remote control transmitter
Batteries
Specifications are subject to change without
notice.
19
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement