Bosch Art Accutrim Instruction manual

F 016 L70 444 - Titel Seite 1 Freitag, 6. März 2009 1:31 13
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
Original brugsanvisning
Bruksanvisning i original
Original driftsinstruks
Alkuperäiset ohjeet
Πρωττυπο οδηγιών
χρήσης
Orijinal iµletme talimat∂
Instrukcja oryginalna
PÛvodní návod k pouÏívání
Pôvodn˘ návod na pouÏitie
Eredeti használati utasítás
Оригинальное руководство по эксплуатации
Оригінальна інструкція з
експлуатації
Instrucøiuni originale
Оригинална инструкция
Originalno uputstvo za rad
Izvirna navodila
Originalne upute za rad
Algupärane kasutusjuhend
Instrukcijas oriinālvalodā
Originali instrukcija
Deutsch
English
Français
Español
Português
Italiano
Nederlands
Dansk
Svenska
Norsk
Suomi
Eλληνικά
Türkçe
Polski
âesky
Slovensky
Magyar
Русский
Українська
Românå
Български
Srpski
Slovensko
Hrvatski
Eesti
Latviešu
Lietuviškai
ART ACCUTRIM
F 016 L70 348.book Seite 2 Mittwoch, 21. Januar 2009 4:24 16
360°
17
1
2
3
4
13
5
16
6
15
7
14
8
12
9
10
11
2 • F 016 L70 444 • 09.03
F 016 L70 348.book Seite 3 Mittwoch, 21. Januar 2009 4:24 16
B1
A
10
➋
6
➊
CLI
CK
!
➊
11
8
➋
B3
B2
18
19
18
11
3 • F 016 L70 444 • 09.03
F 016 L70 348.book Seite 3 Mittwoch, 21. Januar 2009 4:24 16
C
D
20
20
22
21
E
F
➋
5
➊
3
➊
4
6
4 • F 016 L70 444 • 09.03
➋
F 016 L70 348.book Seite 3 Mittwoch, 21. Januar 2009 4:24 16
G
H
6
➊ ➌
18
➋
6
11
90¡
12
I
J
➊
6
➋
5
12
6
8
5 • F 016 L70 444 • 09.03
F 016 L70 348.book Seite 3 Mittwoch, 21. Januar 2009 4:24 16
K
L
9
M
N
9
9
6 • F 016 L70 444 • 09.03
F 016 L70 348.book Seite 3 Mittwoch, 21. Januar 2009 4:24 16
F 016 800 178
F 016 800 172
F 016 800 173
24x
F 016 800 177
(ART 23 ACCUTRIM)
F 016 800 183
(ART 26 ACCUTRIM)
7 • F 016 L70 444 • 09.03
F 016 L70 348.book Seite 1 Mittwoch, 21. Januar 2009 4:24 16
Safety Notes
Warning! Read these instructions carefully, be
familiar with the controls and the proper use of
the trimmer. Please keep the instructions safe
for later use.
Explanation of symbols on the trimmer
General hazard safety alert.
■
■
■
Read instruction manual.
Wear eye protection.
■
■
■
360°
■
Beware of thrown or flying objects to bystanders.
Keep bystanders a safe distance away from the machine.
Remove battery before adjusting or cleaning, and
before leaving the machine unattended for any period.
Do not work in the rain or leave the trimmer
outdoors whilst it is raining.
■ Never operate the trimmer with damaged guards
or shields or without guards or shields in position.
Do not use the charger if the cord is damaged.
■ Before using the machine and after impact, check
for signs of wear or damage and repair if necessary.
■ Do not operate the trimmer when barefoot or
wearing open sandals, always wear substantial
footwear and long trousers.
■ Never allow children or people unfamiliar with
these instructions to use the trimmer. Local regulations may restrict the age of the operator. When
not in use store the trimmer out of reach of children.
■ This appliance is not intended for used by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
15 • F 016 L70 444 • TMS • 13.11.08
■
■
■
■
■
■
–
–
–
■
■
■
■
■
■
Children should be supervised to ensure that they
do not play with the appliance.
Never work with this trimmer while people, especially children or pets are nearby.
The operator or user is responsible for accidents
or hazards occurring to other people or their property.
Wait until the blade has completely stopped before touching it. The blade continues to rotate after the trimmer is switched off, a rotating blade
can cause injury.
Work only in daylight or in good artificial light.
Avoid operating the trimmer in wet grass, where
feasible.
Switch off when transporting the trimmer to and
from the area to be worked on.
Switch on the trimmer with hands and feet well
away from the rotating line.
Do not put hands or feet near the rotating blade.
Never fit metal cutting elements to this trimmer.
Inspect and maintain the trimmer regularly.
Have the trimmer repaired only by an authorized
customer service agent.
Always ensure that the ventilation slots are kept
clear of debris.
Switch off and remove battery from the trimmer:
whenever you leave the machine unattended for
any period
before replacing the blade
before cleaning or working on the trimmer.
Store the machine in a secure dry place out of
reach of children. Do not place other objects on
top of the machine.
Replace worn or damaged parts for safety.
Ensure replacement parts fitted are Bosch approved.
Ensure the switch is in the off position before
inserting battery pack. Inserting the battery
pack into machines that have the switch on invites accidents.
Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
Use machines only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
English - 1
F 016 L70 348.book Seite 2 Mittwoch, 21. Januar 2009 4:24 16
■ When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects that can make a connection
from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
■ Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
Technical data
Trimmer
Part number (typ)
No-load speed
Adjustable handle
Cutting Head angle adjustment/
edging adjustment
Cutting circle
Weight (without optional extras)
Serial Number
Battery type
Part number (typ)
Nominal Voltage
Capacity
Charging time (empty battery)
Battery charger
Part number (typ)
Charging current
– Rapid-charging Procedure
– Trickle-charging Procedure
Allowable charging temperature range
ART 23 ACCUTRIM/
ART 2300 ACCUTRIM
3 600 H78 E..
[min-1] 9 500
●
ART 26 ACCUTRIM/
ART 2600 ACCUTRIM
3 600 H78 F..
9 500
●
●
●
[cm]
23
26
[kg]
2.9
2.9
See serial No 17 (rating plate) on machine.
NiCd
NiCd
2 607 335 535
2 607 335 535
[V]
18
18
[Ah]
1.5
1.5
[min] 85 – 120
85 – 120
AL 60 DV 2411
AL 60 DV 2411
2 607 224 ...
2 607 224 ...
[A]
[mA]
[°C]
Intended Use
1.2
60
0 – 45
1.2
60
0 – 45
Delivered Items
The product is intended for the cutting of grass and
weeds under bushes, as well as on slopes and
edges that can not be reached with the lawn mower.
Intended Use is related to operation within 0 °C and
40 °C ambient temperature.
Introduction
This manual gives instructions on the correct assembly and safe use of your machine. It is important
that you read these instructions carefully.
Carefully remove the machine from its packaging
and check that you have all the following items:
– Trimmer
– Cutting guard
– Adjustable handle (fitted)
– Wheels (ART 26/2600 ACCUTRIM only)
– Plant protector (ART 26/2600 ACCUTRIM only)
– Cutting disc
– Blades
– Battery charger
– Operating instructions
When parts are missing or damaged, please contact your
dealer.
16 • F 016 L70 444 • TMS • 13.11.08
English - 2
F 016 L70 348.book Seite 3 Mittwoch, 21. Januar 2009 4:24 16
Rapid-charging Procedure
Operating Controls
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
On/Off switch
Handle
Handle wing nut
Adjustable handle
Adjusting collar
Shaft
Ventilation slots
Trimmer head
Plant protector (ART 26/2600 ACCUTRIM only)
Cutting guard
Wheels (ART 26/2600 ACCUTRIM only)
Foot pedal for head angle adjustment
Rechargeable battery
LED indicator
Battery charger
Charging compartment
Serial Number
Not all of the accessories illustrated or described are
included as standard delivery.
For Your Safety
Warning! Switch off, remove battery from machine before adjusting or cleaning.
The blade continues to rotate for a few seconds after the trimmer is switched off.
Caution – do not touch rotating blade.
Charging Procedure
The charging procedure starts as soon as the mains
plug is plugged into the socket and the battery 13 is
inserted into the charging compartment 16.
Due to the intelligent charging method, the charging
condition of the battery is automatically detected and
the battery is charged depending on battery temperature and voltage.
This gives longer life to the battery and always
leaves it fully charged when kept in the charger for
storage.
Control of the charging procedure is indicated via
the charge control LED 14:
17 • F 016 L70 444 • TMS • 13.11.08
The rapid-charging procedure is indicated by flashing of the charge
control LED 14.
The battery is fully charged as soon as the LED 14
switches from flashing to being lit continuously. Afterwards the battery can be removed for immediate
use.
It is recommended not to remove the battery until the
battery is fully charged.
The rapid-charging procedure is possible only
when the temperature of the battery is between 0 °C and 45 °C.
☞
Trickle-charging Procedure
The trickle-charging procedure is indicated by continuous lighting of
the LED 14.
With the battery fully charged, the charger immediately switches to trickle-charge mode. This equalizes the natural running-down of the battery again.
Charging Advice
With continuous or several repetitive charging cycles without interruption, the charger can warm up.
This is not harmful and does not indicate a technical
defect of the unit.
A battery 13 that is new or has not been used for a
longer period does not develop its full capacity until
after approximately 5 charging/discharging cycles.
Leave such batteries 13 in the charging compartment 16 until they have clearly warmed up.
A significantly reduced working period after charging
indicates that the batteries are worn out and must be
replaced.
Assembly
Do not connect the battery before product
is completely assembled.
Ensure product is assemble in the following order:
A Mounting the Cutting Guard
Place the cutting guard 10 on the trimmer head 8.
➊ Hook the guard onto trimmer head and push until
secure fitting.
➋ Push rear of guard until secure (click).
English - 3
F 016 L70 348 - GB Seite 4 Freitag, 23. Januar 2009 8:53 08
Mounting the Wheels
(ART 26/2600 ACCUTRIM only)
B1 Fit the wheels 11 onto the shaft 6.
B2 Fit the bolt 19 and the wingnut 18.
Note: The position of the wheels can be adjusted by
loosening the wingnut 18 and moving to the desired
position.
B3 The wheels can be moved up and down the
shaft 6 depending on the height of cut required.
Fitting Cutting Disc/Fitting Blade
C Press cutting disc 20 onto drive adaptor as
shown (click).
D Fit the blade, place the blade 22 over the pivot 21
and pull outwards until it snaps into place.
Adjustment
E Using Adjustable Handle
The adjustable handle 4 can be set in various positions:
➊ To
change the position undo the handle wing
nut 3 and move the adjustable handle 4.
➋ Tighten the handle wing nut 3 securely to fix the
adjustable handle 4 in the adjusted position.
F Adjusting Product Length
➊ Loosen the adjustment collar 5 90°.
➋ Pull the shaft out to increase the height, or push
the shaft in to decrease the height. Re-tighten adjustment collar 5.
G Adjusting cutting head angle:
To change the angle depress the foot pedal 12 and
move the shaft 6 to the desired position.
Release the foot pedal 12.
Adjusting for Edging Mode
H Moving wheels (where fitted):
➊ Loosen wingnut 18.
➋ Twist wheels 11 90° as shown.
Cutting and Edging
Remove stones, loose pieces of wood and
other objects from the cutting area.
The blade continues to rotate for a few seconds
after the trimmer is switched off. Allow the motor/blade to stop rotating before switching “on”
again.
Do not rapidly switch off and on.
Switching On and Off
Press switch 1 and hold depressed. Release
switch 1 for switching off.
K Cutting Grass
Move the trimmer left and right, keeping it well away
from the body.
The trimmer can efficiently cut grass up to a height
of 15 cm. Cut taller grass in stages.
Remove the wheels when cutting long grass
(ART 26/2600 ACCUTRIM only).
L Trimming Edges
Guide the trimmer along the edge of the lawn. Do not
allow the cutting line to contact paved surfaces,
stones or garden walls, since this will wear the blade
rapidly.
M For better control use the plant protector 9
(ART 26/2600 ACCUTRIM only – available as an
accessory for ART 23/2300 ACCUTRIM) as a guide.
N Cutting Around Trees and Bushes
Carefully cut around trees and bushes so that they
do not come into contact with the cutting line.
Plants can die if you damage the bark.
M For better control use adjustable handle 4 and
use the plant protector 9 (ART 26/2600 ACCUTRIM
only – available as an accessory for
ART 23/2300 ACCUTRIM).
➌ Tighten wingnut 18.
I Adjusting cutting head angle:
➊ Depress the foot pedal 12.
➋ Move the shaft 6 to the lowest position. Release
the foot pedal 12.
J Move trimmer head:
➊ Loosen the adjustment collar 5.
➋ Turn the shaft 6 90° to position the trimmer
head 8 for trimming/edging as shown. Re-tighten
adjustment collar 5.
18 • F 016 L70 444 • TMS • 13.11.08
English - 4
F 016 L70 348.book Seite 5 Mittwoch, 21. Januar 2009 4:24 16
Battery duration
Battery duration is dependent on the working conditions:
light conditions:
up to 800 metres
medium conditions:
up to 350 metres
tough conditions:
up to 60 metres
D
Blade Maintenance
Before any work on the machine itself, remove battery from machine.
To remove the worn blade 22 push in direction of the
arrow until it snaps off the pivot 21.
Clean the pivot 21 of any residual plastic/debris with
a sharp knife.
To refit the new blade 22 place the eyelet over the
pivot 21 and pull outwards until it snaps into place.
Note: Only use Bosch replacement blades. They
have been developed specially for improved cutting
performance. The use of other cutter blades will lead
to a deterioration in performance and possible damage to the product.
After Trimming/Storage
Maintenance
Before any work on the machine itself, remove battery from machine.
Note: To ensure long and reliable service, carry out
the following maintenance regularly.
Regularly check for obvious defects such as loose
fixings, and worn or damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using.
If the trimmer should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorized customer service agent
for Bosch garden products.
For all correspondence and spare parts orders, always include the 10-digit part number (TYP) from
the nameplate of the machine!
19 • F 016 L70 444 • TMS • 13.11.08
Stop and remove battery from product. Ensure battery is removed before storage.
Clean the exterior of the machine thoroughly using a
soft brush and cloth. Do not use water, solvents or
polishes. Remove all grass and debris, especially
from the ventilation slots 7.
Turn the machine on its side and clean the cutting
guard 10 inside. If grass cuttings are compacted, remove with a wooden or plastic implement.
Battery should be stored between 0 – 45 °C; incorrect storage could result in the battery being damaged.
English - 5
F 016 L70 348.book Seite 6 Mittwoch, 21. Januar 2009 4:24 16
Fault Finding
The following table gives checks and actions that you can perform if your machine does not operate correctly.
If these do not identify/remedy the problem, contact your service agent.
Warning: Switch off and remove battery before investigating fault.
Symptom
Possible Cause
Remedy
Can not fit Guard over Incorrect assembly
cutting disc
Remove cutting disc and fit guard, see
also Product assembly
Machine fails to operate
Recharge battery, see also Charging
advice
Machine
intermittently
Battery discharged
functions Machines internal witing damaged
On/Off switch defective
Excessive vibration/
noise
Machine fault
Blade broken
Contact Service Agent
Contact Service Agent
Contact Service Agent
Replace blade
Cutting time low on one Battery not used for long period or ini- Fully charge battery, see also charging
battery charge
tial usage
advice
Grass too high
Cut in stages
Battery worn out
Replace the battery
Blade will not move
Battery discharged
Recharge battery, see also Charging
advice
Contact Service Agent
Machine fault
Machine is not cutting
Blade broken
Battery not fully charged
Grass entangled around cutting disc
Replace blade
Recharge battery, see also Charging
advice
Remove grass
No charging procedure The battery temperature is not within Get the battery temperature within the
possible due to defective the allowable temperature range
allowable temperaturerange (0 °C to
battery
45 °C) either by cooling down or warming up. As soon as the battery temperature is within the allowable temperature range again, the battery charger
automatically switches to rapid charging
The contacts of the battery are con- Clean the contacts (e. g. by inserting
taminated
and removing the battery several
times) or replace the battery, as required
The battery is defective, due to a dis- Replace the battery
connection in the battery (individual
cells)
The LED indicator 14 The charger plug is not inserted (propdoes not light up after erly)
plugging the mains plug Socket, cable or charger are defective
into the socket and inserting the battery into the
charging compartment 16
20 • F 016 L70 444 • TMS • 13.11.08
English - 6
Insert the plug (fully) into the socket
Check the mains voltage and if necessary, have the battery charger
checked by an authorized customer
service station for Bosch power tools
F 016 L70 348.book Seite 7 Mittwoch, 21. Januar 2009 4:24 16
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According to the European Directive
2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, products that
are no longer suitable for use must be separately
collected and sent for recovery in an environmentally-friendly manner.
After-Sales Service and
Customer Assistance
Our after-sales service responds to your questions
concerning maintenance and repair of your product
as well as spare parts. Exploded views and information on spare parts can also be found under:
www.bosch-pt.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty.Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
21 • F 016 L70 444 • TMS • 13.11.08
Inside Australia:
Phone: +61 (01300) 307 044
Fax: + 61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Declaration of Conformity
Measured values determined according to
2000/14/EC (1.60 m height, 1 m distance away) and
EN ISO 5349.
Typically the A-weighted noise levels of the product
are: Sound pressure level 72 dB(A); Guaranteed
sound power level lower than 93 dB(A). Uncertainty
K = 3 dB.
The typical hand/arm vibration is below 2.5 m/s 2.
We declare under our sole responsibility that the
product described under „Technical data“ is in conformity with the following standards or standardization documents: EN 60335 (battery powered product) and EN 60335 (battery charger) according to
the provisions of the directives 2006/95/EC,
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009), 2000/14/EC.
2000/14/EC: Measured sound power level
88 dB(A).
Conformity assessment procedure according to Annex VI.
Notified body: SRL, Sudbury, England
Notified body identification number: 1088
Technical file at: Bosch Lawn and Garden Ltd., PTLG/EAE, Stowmarket, Suffolk IP14 1EY, England
08
Leinfelden, 01.01.2008
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
Robert Bosch GmbH, Power Tools Division
Subject to change without notice
English - 7