Bosch KBE-335V55-20 Instruction manual

KBE and KBN Series
en
Instruction Manual
AutoDome, Bilinx, Bosch, the Bosch logo, DiBos, FastAddress and VIDOS are registered trademarks of Bosch Security Systems, inc.
The following trademarks are registered with the United States Patent and Trademark Office:
Pentium is a registered trademark of Intel Corporation
.NET, DirectX, Internet Explorer, Microsoft, Windows, Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation
Due to the nature of this material, this document refers to numerous hardware and software products by their trade names, In most, if not all
cases, these designations are claimed as trademarks or registered trademarks by their respective companies in the United States of America. It is
not this publisher’s intent to use any of these names generically. The reader is therefore cautioned to investigate all claimed trademark rights before using any of these names other than to refer to the product described.
KBE and KBN Series
| en
iii
Preface
This guide describes how to install the KBE and KBN Series.
Audience
This guide is intended for qualified installation and service personnel who are familiar with the applicable national
and local electrical codes.
Document Conventions
Convention
Bold
Italic
Underline
courier
Meaning
Denotes a part, item, or assembly.
Denotes a reference to another paragraph, figure or table.
Used to emphasize a point.
Denotes the actual name of an object, the exact code that should be typed or a message
returned from a system.
Symbols
You may encounter these symbols within the document. Explanatory text accompanies each symbol, which provides
additional information detailing the operation or highlighting safety information.
i
!
!
NOTICE! Notices inform you of essential but non-critical information. Read these messages
carefully as any directions or instructions contained therein can help you avoid making
mistakes.
CAUTION! Cautionary messages provide critical information that help you reduce the chance
of losing data or damaging the system. Please heed these messages.
WARNING! Warnings highlight information, that if overlooked may cause damage to the
system or result in personal injury. Take warnings seriously.
DANGER! Danger messages denote the presence of electrical equipment that may cause
electric shock or electrocution. Take care when you see this symbol to avoid serious injury or
death.
Bosch Security Systems, Inc.
Instruction Manual
F01U065975 | 1.0 | 2007.04
iv
en |
KBE and KBN Series
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and
shipping instructions.
Service Centers
USA
Phone: 800-366-2283 or 585-340-4162
Fax: 800-366-1329
Email: cctv.repair@us.bosch.com
Technical Support
Phone: 800-326-1450
Email: technical.support@us.bosch.com
CCTV Spare Parts
Phone: 800-894-5215 or 408-957-3065
Fax: 408-935-5938
Email: BoschCCTVparts@ca.slr.com
Canada
Phone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East & Asia Pacific Region
Phone: 44 (0) 1495 274558
Fax: 44 (0) 1495 274280
Email: rmahelpdesk@solectron.com
For additional information, see www.boschsecurity.com
Related Publications
Refer to the latest Bosch Security Systems, Inc. Databook for the most up-to-date datasheets. To obtain a copy of
the Databook, please contact your local Bosch representative.
You can also visit the Bosch Security Systems World Wide Web site at: http://www.boschsecurity.com to view a current listings of our publications.
F01U065975 | 1.0 | 2007.04
Instruction Manual
Bosch Security Systems, Inc.
| en
v
Important Safeguards
1. Read, Follow, and Retain Instructions - All safety and operating
instructions should be read and followed before operating the unit.
Retain instructions for future reference.
2. Heed Warnings - Adhere to all warnings on the unit and in the operating instructions.
3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause hazards.
4. Installation Cautions - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious injury to
a person and serious damage to the unit. Use only manufacturer-recommended accessories, or those sold with the product. Mount the
unit per the manufacturer's instructions. Appliance and cart combination should be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart combination to
overturn.
5. Cleaning - Unplug the unit from the outlet before cleaning. Follow any
instructions provided with the unit. Generally, using a damp cloth for
cleaning is sufficient. Do not use liquid cleaners or aerosol cleaners.
6. Servicing - Do not attempt to service this unit yourself. Opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
7. Damage Requiring Service - Unplug the unit from the main AC power
source and refer servicing to qualified service personnel under the
following conditions:
•
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled or an object has fallen into the unit.
If the unit has been exposed to water and/or inclement weather
(rain, snow, etc.).
• If the unit does not operate normally, when following the operating instructions. Adjust only those controls specified in the operating instructions. Improper adjustment of other controls may
result in damage, and require extensive work by a qualified technician to restore the unit to normal operation.
• If the unit has been dropped or the cabinet damaged.
• If the unit exhibits a distinct change in performance, this indicates
that service is needed.
8. Replacement Parts - When replacement parts are required, the service technician should use replacement parts specified by the manufacturer or that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electrical shock or
other hazards.
9. Safety Check - Upon completion of servicing or repairs to the unit,
ask the service technician to perform safety checks to ensure proper
operating condition.
Bosch Security Systems, Inc.
10.Power Sources - Operate the unit only from the type of power source
indicated on the label. If unsure of the type of power supply to use,
contact your dealer or local power company.
•
For units intended to operate from battery power, refer to the
operating instructions.
• For units intended to operate with External Power Supplies, use
only the recommended approved power supplies.
• For units intended to operate with a limited power source, this
power source must comply with EN60950. Substitutions may
damage the unit or cause fire or shock.
• For units intended to operate at 24VAC, normal input voltage is
24VAC. Voltage applied to the unit's power input should not
exceed 30VAC.
User-supplied wiring, from the 24VAC supply to unit, must be in compliance with electrical codes (Class 2 power levels). Do not ground
the 24VAC supply at the terminals or at the unit's power supply terminals.
11.Coax Grounding - If an outside cable system is connected to the unit,
ensure that the cable system is grounded. U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting
structure, grounding of the coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
12.Grounding - This unit may be equipped with a 3-wire grounding plug
(a plug with a third pin, for grounding). This safety feature allows the
plug to fit into a grounding power outlet only. If unable to insert the
plug into the outlet, contact an electrician to arrange replacement of
the obsolete outlet. Do not defeat the safety purpose of the grounding plug.
•
•
•
Outdoor equipment should only be connected to the unit's inputs
after this unit has had its grounding plug connected to a grounded
outlet or its ground terminal properly connected to a ground
source.
The unit's input connectors must be disconnected from outdoor
equipment before disconnecting the grounding plug or grounding
terminal.
Proper safety precautions such as grounding should be followed
for any outdoor device connected to this unit.
13.Lightning - For added protection during a lightning storm, or when
this unit is left unattended and unused for long periods of time,
unplug the unit from the wall outlet and disconnect the cable system.
This will prevent damage to the unit due to lightning and power line
surges.
vi
en |
For Indoor Product
WARNING:
1. Water and Moisture - Do not use this unit near water for example, in a wet basement, in an unprotected outdoor installation or in any area classified as a wet location.
Electrostatic-sensitive device. Use proper CMOS/
MOSFET handling precautions to avoid electrostatic discharge.
2. Object and Liquid Entry - Never push objects of any
kind into this unit through openings, as they might touch
dangerous voltage points or create short circuits, resulting in a fire or electrical shock. Never spill liquid of any
kind on the unit.
3. Power Cord and Power Cord Protection - For units
intended to operate with 230VAC, 50Hz, the input and
output power cord must comply with the latest versions
of IEC Publication 227 or IEC Publication 245. Power
supply cords should be routed so they are not likely to
be walked on or pinched. Pay particular attention to
location of cords and plugs, convenience receptacles,
and the point of exit from the appliance.
4. Overloading - Do not overload outlets and extension
cords; this can result in a risk of fire or electrical shock.
For Outdoor Product
Power Lines - An outdoor system should not be located
in the vicinity of overhead power lines, electric lights or
power circuits, or where it may contact such power lines
or circuits. When installing an outdoor system, extreme
care should be taken to keep from touching power lines
or circuits, as this contact might be fatal. U.S.A. models
only - refer to the National Electrical Code Article 820
regarding installation of CATV systems.
For Rack-mount Product
1. Ventilation - Do not place this equipment in a built-in
installation or rack, unless proper ventilation is provided, or the manufacturer's instructions were followed.
The equipment must not exceed its maximum operating
temperature requirements.
NOTE: Grounded wrist straps must be worn and
proper ESD safety precautions observed when
handling the electrostatic-sensitive printed circuit
boards.
This symbol indicates the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Cover Removal
Warning: Removal of the cover should only be
performed by qualified service personnel - not
user serviceable. The unit should always be
unplugged before removing the cover and remain
unplugged while the cover is removed.
24 VAC Units
Do not exceed 30VAC input. Voltage applied to the unit's
power input should not exceed 30VAC. Normal input voltage is
24VAC. User supplied wiring from 24VAC supply to unit must
be in compliance with electrical codes (Class 2 power levels).
Do not ground 24VAC supply at power supply terminals or at
unit's power supply terminals.
This equipment is to be isolated from the mains
supply by a limited power source as specified in
EN60950.
220-240V, 50Hz Power Cords
220-240V, 50Hz power cords, input and output, must comply
with the latest versions of IEC Publication 227 or IEC Publication 245.
2. Mechanical Loading - When rack-mounting the equipment, ensure that a hazardous condition is not created
by uneven mechanical loading.
Bosch Security Systems, Inc.
| en
FCC & ICES INFORMATION
Safety Precautions
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules
and ICES-003 of Industry Canada. These limits are designed to provide
reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates,
uses and radiates radio frequency energy, and if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at his expense.
Intentional or unintentional changes or modifications, not expressly
approved by the party responsible for compliance, shall not be made.
Any such changes or modifications could void the user’s authority to
operate the equipment. If necessary, the user should consult the dealer
or an experienced radio/television technician for corrective action. The
user may find the following booklet, prepared by the Federal Communications Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government
Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
WARNING: This is a Class A product. In a domestic environment, this product may cause radio interference, in which
case, the user may be required to take adequate measures.
Bosch Security Systems, Inc.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol indicates the presence of uninsulated
“dangerous voltage” within the product’s enclosure that can cause an electric shock.
This symbol indicates the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Installation should be performed by qualified service personnel only in accordance with the
National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF
switches have power supplied to the unit whenever the power cord is inserted into the power
source; however, the unit is operational only when
the ON-OFF switch is in the ON position. The
power cord is the main power disconnect for all
units.
vii
viii
en |
INFORMATIONS FCC ET ICES
Sécurité
(modèles utilisés aux États-Unis et au Canada uniquement)
Attention: l'installation doit exclusivement être réalisée par du
Ce produit est conforme aux normes FCC partie 15. la mise en service
est soumises aux deux conditions suivantes:
(1) cet appareil ne peut pas provoquer d'interférence nuisible et
(2) cet appareil doit pouvoir tolérer toutes les interférences auxquelles
il est soumit, y compris les interférences qui pourraient influer sur
son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé conforme aux exigences imposées aux appareils numériques de Classe A en
vertu de la section 15 du règlement de la Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont destinées à
fournir une protection raisonnable contre les interférences nuisibles
quand l'appareil est utilisé dans une installation commerciale. Cette
appareil génère, utilise et émet de l'energie de fréquence radio, et peut,
en cas d'installation ou d'utilisation non conforme aux instructions,
générer des interférences nuisibles aux communications radio. L’utilisation de ce produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas échéant, l’utilisateur devra remédier à ces
interférences à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision, qui procédera à une opération corrective. La brochure suivante, publiée par la Commission fédérale des communications
(FCC), peut s’avérer utile : « How to Identify and Resolve Radio-TV Interference Problems » (Comment identifier et résoudre les problèmes
d’interférences de radio et de télévision). Cette brochure est disponible
auprès du U.S. Government Printing Office, Washington, DC 20402,
États-Unis, sous la référence n° 004-000-00345-4.
Avertissement : Ce produit est un appareil de Classe A. Son
utilisation dans une zone résidentielle risque de provoquer
des interférences. Le cas échéant, l’utilisateur devra prendre
les mesures nécessaires pour y remédier.
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION, N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN
COMPOSANT SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILISATEUR. CONFIEZ LA RÉPARATION DE L'APPAREIL À DU
PERSONNEL QUALIFIÉ.
Ce symbole signale que le produit renferme une «
tension potentiellement dangereuse » non isolée
susceptible de provoquer une électrocution.
Ce symbole invite l'utilisateur à consulter les
instructions d'utilisation et d'entretien (dépannage) reprises dans la documentation qui
accompagne l'appareil.
Attention: l'installation doit exclusivement être
réalisée par du personnel qualifié, conformément
au code national d'électricité américain (NEC) ou
au code d'électricité local en vigueur.
Coupure de l'alimentation. Qu'ils soient pourvus
ou non d'un commutateur ON/OFF, tous les appareils reçoivent de l'énergie une fois le cordon
branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque le
commutateur est réglé sur ON. Le débranchement
du cordon d'alimentation permet de couper l'alimentation des appareils.
Bosch Security Systems, Inc.
| en
AVERTISSEMENT:
cet appareil est sensible aux décharges électrostatiques. Pour éviter tout risque de décharge électrostatique, observez les précautions de
manipulation du CMOS/MOSFET appropriées.
REMARQUE: lors de la manipulation des cartes à
circuits imprimés sensibles aux décharges électrostatiques, portez des bracelets antistatiques
mis à la terre et observez les consignes de sécurité relatives aux décharges électrostatiques.
ATTENTION: pile au lithium
Le remplacement incorrect de la pile risque de
provoquer une explosion. Remplacez la pile exclusivement par une pile identique ou par un type de
pile équivalent recommandé par le fabricant.
Débarrassez-vous de la pile usagée conformément
aux instructions de son fabricant.
Enlèvement du capot
Avertissement: L’enlèvement du capot ne doit
être effectué que par un technicien spécialisé. Il
n’y a pas de pièces remplaçables ou réglables par
l’utilisateur. Il faut toujours débrancher l’appareil
avant d’enlever le capot et le laisser débranché
jusqu’à la remise en place du capot.
24 VAC Units
Ne pas excéder 30 V c.a. La tension appliquée à l’entrée d’alimentation de l’appareil ne doit pas excéder 30 V c.a. La valeur
normale de la tension d’entrée est 24 V c.a. Le circuit électrique reliant l’alimentation 24 V c.a. à l’appareil doit être conforme aux codes électriques (niveaux d’alimentation de classe
2). Ne pas mettre l’alimentation 24 V c.a. à la masse au niveau
des bornes de l’alimentation ou de l’appareil.
Cet équipement doit être isolé de l’alimentation
secteur par une source de puissance limitée, conformément à la norme EN60950.
Cordons d’alimentation 220-240 V, 50 Hz
Les cordons d’alimentation 220-240 V, 50 Hz, d’entrée ou de
sortie, doivent être conformes à la dernière version de la publication IEC 227 ou IEC 245.
Bosch Security Systems, Inc.
ix
x
en |
Bosch Security Systems, Inc.
KBE and KBN Series
| en xi
Table of Contents
1
Unpacking
1
1.1
Parts List
1
2
Description
1
2.1
Model Summary
1
3
Installation
1
3.1
Operating Voltage
1
3.2
Preparing the Unit
1
3.3
Preparing the Mount
1
3.4
Housing
2
3.5
Line Power and Video Signal Connection
2
3.6
Connections for U Suffix, F Suffix, and N Suffix
2
3.6.1
U (Twisted Pair) Suffix Connections
2
3.6.2
Wiring Do’s
3
3.6.3
Wiring Don’ts
3
3.6.4
F (Fiber Optic) Suffix Connections
4
3.6.5
N (Network) Suffix Connections
6
4
Camera Lens Adjustment
7
5
Sunshield
8
6
Model Numbers and System Specifications
8
Bosch Security Systems, Inc.
Instruction Manual
F01U065975 | 1.0 | 2007.04
xii
en | Table of Contents
F01U065975 | 1.0 | 2007.04
KBE and KBN Series
Instruction Manual
Bosch Security Systems, Inc.
KBE and KBN Series
1
Unpacking | en 1
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in the Parts List below are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.
1.1
Parts List
Qty
1
Item
Unit (verify package model
1
1
number ordered)
Feed-through mount
Instruction booklet packet
Refer to Section 6 Model Numbers and System Specifications for a detailed list of the Camera,
Lens, Housing, and Feed-through Mount model numbers included with the various package
model numbers.
2
Description
The KBE and KBN Series are complete camera packages that include a camera and lens prewired into a housing. A feed-through wall mount is also provided, as well as a sunshield on
outdoor packages.
2.1
Model Summary
Refer to Section 6 Model Numbers and System Specifications for the resolution, lens, and
system specifications for the various package models.
3
Installation
!
3.1
This installation should be made by a qualified service person and conform to all local codes.
Operating Voltage
All Recommended operating voltage is 24 VAC, 60 Hz.
3.2
Preparing the Unit
Remove the mount and the housing assembly from the carton.
3.3
Preparing the Mount
Prepare and secure the mount to the wall or mounting surface as described in the
LTC 9215/00 Installation Manual included in the Instruction Booklet Packet.
Bosch Security Systems, Inc.
Instruction Manual
F01U065975 | 1.0 | 2007.04
2 en | Installation
3.4
KBE and KBN Series
Housing
Feed the cabling from the housing foot through the mount. Attach the housing to the mount
using the two (2) 1/4-20 screws and washers provided in the hardware kit. For additional
information, refer to the LTC 9215/00 Mount Installation Manual and UHO-HBGS-10 Series
Housing Installation Manual.
3.5
Line Power and Video Signal Connection
The external video coax cable is equipped with a female BNC connector for transmission of
video. Route and connect video cable to the BNC connector. The external power cable is
provided to allow for necessary stripping/preparation by the installer. For additional
information, refer to the Installation Manuals included in the Instruction Booklet Packet.
Color
Green
White
Black
3.6
Connection
Ground
24 V
24 V
Connections for U Suffix, F Suffix, and N Suffix
The connections for models containing fiber optic, network, or twisted pair interfaces are
covered as follows:
3.6.1
U (Twisted Pair) Suffix Connections
These models include an unshielded twisted pair transmitter added to the standard
construction.
1.
Make all power connections in accordance with the KBE and KBN Series Instruction
Manual.
2.
Pass the supplied orange string through the mounting foot of the camera housing and the
furnished mount. See Figure 3.2. A fitting may be used in the mounting foot if desired.
3.
Attach the end of the string to the unshielded twisted pair (UTP) video cable and pull it
through the mount and the unused hole in the mounting foot of the camera housing as
shown in Figure 3.3.
4.
Connect the UTP video cable to the the -VID+ pins on UTP transmitter. Observe polarity;
the video connection is polarity-sensitive. See Figure 3.1.
Figure 3.1 Connecting the UTP Cable to the Transmitter
Reference
1
2
5.
Description
Negative (-) terminal for twisted pair video lead
Positive (+) terminal for twisted pair video lead
Seal the hole in the mounting foot of the camera housing with RTV or an equivalent seal.
If a fitting was used in the mounting foot, apply the seal around the UTP cable before
tightening the fitting to prevent slippage.
F01U065975 | 1.0 | 2007.04
Instruction Manual
Bosch Security Systems, Inc.
KBE and KBN Series
Installation | en 3
6.
Attach the housing to the mount in accordance with the KBE and KBN Series Instruction
Manual.
3.6.2
Wiring Do’s
1.
Use point to point unshielded twisted pair wire, 24 AWG or thicker, stranded or solid,
Category 2, 3, 4, or 5.
2.
The video signal may coexist in the same wire bundle as other video, telephone, data,
control signals, or low voltage power.
3.
Measure the wire distance. Use only receivers designed for that distance.
4.
Make sure the pair of wires carrying the video signal is sent as a twisted pair, not a split
pair.
3.6.3
Wiring Don’ts
1.
DO NOT USE SHIELDED TWISTED PAIR WIRE, as this will severely degrade the distance
performance. Short runs may be used with some signal degradation. Multi-pair wire with
an overall shield is OK.
2.
DO NOT USE UNTWISTED WIRE, as this will reduce the inherent immunity to
interference.
3.
DO NOT allow your installation to have bridge/ taps, loading coils, talk-battery, or MOV
type protectors. Bridge taps refer to a twisted pair connected to two twisted pairs (such
as an extension phone). Bridge taps cause reflections as the signal propagates, resulting
in ghosts in the image.
4.
If the phone company is providing the cable runs between buildings, make sure it is dry
copper (i.e. it should have none of the following: dial tone, 48 V, loading coils, bridge
taps, switching, or long paths to the phone company's central office and back).
5.
Due to near-end cross talk, DO NOT send a transmit and receive signal in the same wire
bundle. Exceptions: Less than 1000 ft (304.8 m), or Category 5 cable up to 609.6 m
(2000 ft).
6.
Bosch Security Systems, Inc.
For safety, never put signals in the same conduit as high voltage wiring.
Instruction Manual
F01U065975 | 1.0 | 2007.04
4 en | Installation
3.6.4
KBE and KBN Series
F (Fiber Optic) Suffix Connections
These models include a fiber optic transmitter added to the standard construction.
1.
Make all power connections in accordance with the KBE and KBN Series Instruction
Manual.
2.
Pass the supplied orange string through the mounting foot of the camera housing and the
furnished mount. See Figure 3.2. Note that a fitting is not used in the mounting foot when
a terminated fiber optic cable is used.
Figure 3.2 Passing the String through the Mount
Reference
1
3.
Description
Orange String
Attach the end of the string to the fiber optic video cable and pull it through the mount
and the unused hole in the mounting foot of the camera housing. See Figure 3.3.
Figure 3.3 Pulling the Fiber Optic Cable
Reference
1
2
3
F01U065975 | 1.0 | 2007.04
Description
Orange string
ST / RJ-45 connector
Fiber optic video cable / UTP/CAT5 cable
Instruction Manual
Bosch Security Systems, Inc.
KBE and KBN Series
Installation | en 5
4.
Connect the fiber optic cable to the fiber optic video connector on the fiber optic
transmitter. See Figure 3.4.
!
CAUTION! Make sure that the bend radius of the fiber optic cable is in accordance with the
cable manufacturer’s specifications when dressing the fiber optic cable.
Figure 3.4 Connecting the Fiber Optic Cable to the Transmitter
Reference
1
2
5.
Description
Fiber optic cable
Video connector on fiber optic transmitter
If an unterminated fiber optic cable is being used, a fitting may be used in the mounting
foot of the camera housing. The fiber optic cable should be terminated with an ST
connector in accordance with the connector manufacturer’s recommendations.
6.
Seal the hole in the mounting foot of the camera housing with RTV or an equivalent seal.
See Figure 3.5. If a fitting was used in the mounting foot along with an unterminated fiber
optic cable, apply the seal around the optical cable before tightening the fitting, to
prevent slippage. A split rubber sleeve (not supplied) may be used for this purpose.
Figure 3.5 Seal the Hole in the Housing Foot
Reference
1
7.
Description
Seal with RTV
Attach the housing to the mount in accordance with the KBE and KBN Series Instruction
Manual.
Bosch Security Systems, Inc.
Instruction Manual
F01U065975 | 1.0 | 2007.04
6 en | Installation
3.6.5
KBE and KBN Series
N (Network) Suffix Connections
These models include an IP-based camera that enables network video and configuration
capabilities.
1.
Make all power connections in accordance with the KBE and KBN Series Instruction
Manual.
!
WARNING! Never supply power via the Ethernet connection (PoE) when power is supplied via
the power connector.
2.
Connect the camera to a 10/100 Base-T network (Figure 3.6).
3.
Use a shielded UTP Category 5 cable with RJ-45 connectors.
Figure 3.6 Network Connection
4.
Power can be supplied one of two ways: 24 VAC power connection (factory configured),
or via the Ethernet cable compliant with the Power-over-Ethernet (IEEE 802.3af)
standard. Note: For POE remove 24 VAC connections at terminals shown in Figure 3.7.
Figure 3.7 Power Wire Connection
Reference
1
5.
Description
Power terminals
Pass the supplied orange string through the mounting foot of the camera housing and the
furnished mount. See Figure 3.2. A fitting may be used in the mounting foot if desired.
6.
Attach the end of the string to the Cat5/Cat6 cable and pull it through the mount and the
unused hole in the mounting foot of the camera housing. See Figure 3.3.
7.
Connect the Cat5/ Cat6 cable to the network connector on the back of the camera. See
8.
If an unterminated Cat5/Cat6 cable is being used, a fitting may be used in the mounting
Figure 3.6.
foot of the camera housing. The network cable should be terminated with an RJ-45
connector in accordance with the connector manufacturer’s recommendations.
9.
Seal the hole in the mounting foot of the camera housing with RTV or an equivalent seal.
See Figure 3.5. If a fitting was used in the mounting foot, apply the seal around the
network cable before tightening the fitting, to prevent slippage. A split rubber sleeve (not
supplied) may be used for this purpose.
F01U065975 | 1.0 | 2007.04
Instruction Manual
Bosch Security Systems, Inc.
KBE and KBN Series
4
Camera Lens Adjustment | en 7
Camera Lens Adjustment
The camera and lens come factory configured and ready for operation. If custom setup is
required, refer to the camera Installation Instructions included in the Instruction Booklet
Packet.
Figure 4.1 Removing the Bracket
Bosch Security Systems, Inc.
Instruction Manual
F01U065975 | 1.0 | 2007.04
8 en | Sunshield
5
KBE and KBN Series
Sunshield
A sunshield is provided with the outdoor packages.
6
Model Numbers and System Specifications
Model No.
Camera
Lens
Housing
MONOCHROME 1/3 in. STANDARD RESOLUTION
KBN-335V28-20 LTC 0335/20 LTC 3364/50
LTC 9480/00
Mount
Resolution Included Lens System
LTC 9215/00S
380
2.8-10 mm
Indoor, Monochrome
EIA, 24 VAC, 60 Hz
Outdoor, Monochrome
KBE-335V28-20
LTC 0335/20
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
380
Vari-focal
2.8-10 mm
KBN-335V55-20
LTC 0335/20
LTC 3374/50
LTC 9480/00
LTC 9215/00S
380
Vari-focal
EIA, 24 VAC, 60 Hz
5-50 mm Vari- Indoor, Monochrome
KBE-335V55-20
LTC 0335/20
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
380
focal
EIA, 24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Monochrome
MONOCHROME 1/3 in. HIGH RESOLUTION
KBN-355V28-20 LTC 0355/20 LTC 3364/50
LTC 9480/00
LTC 9215/00S
focal
EIA, 24 VAC, 60 Hz
570
2.8-10 mm
Indoor, Monochrome
EIA, 24 VAC, 60 Hz
Outdoor, Monochrome
KBE-355V28-20
LTC 0355/20
LTC 3364/50
UHO-HBGS-10
LLTC 9215/00 570
Vari-focal
2.8-10 mm
KBN-355V55-20
LTC 0355/20
LTC 3374/50
LTC 9480/00
LTC 9215/00S
570
Vari-focal
EIA, 24 VAC, 60 Hz
5-50 mm Vari- Indoor, Monochrome
KBE-355V55-20
LTC 0355/20
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
570
focal
EIA, 24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Monochrome
MONOCHROME 1/3 in. HIGH RESOLUTION SENSITIVITY
KBN-385V28-20 LTC 0385/20 LTC 3364/50
LTC 9480/00
LTC 9215/00S
focal
EIA, 24 VAC, 60 Hz
570
2.8-10 mm
Indoor, Monochrome
EIA, 24 VAC, 60 Hz
Outdoor, Monochrome
KBE-385V28-20
LTC 0385/20
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
570
Vari-focal
2.8-10 mm
KBE-385V28-20F
LTC 0385/20
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
570
Vari-focal
2.8-10 mm
EIA, 24 VAC, 60 Hz
Outdoor, Monochrome
Vari-focal
EIA, 24 VAC, 60 Hz, w/
2.8-10 mm
Fiber
Outdoor, Monochrome
Vari-focal
EIA, 24 VAC, 60 Hz, w/
KBE-385V28-20U LTC 0385/20
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
570
KBN-385V55-20
LTC 0385/20
LTC 3374/50
LTC 9480/00
LTC 9215/00S
570
UTP
5-50 mm Vari- Indoor, Monochrome
KBE-385V55-20
LTC 0385/20
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
570
focal
EIA, 24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Monochrome
KBE-385V55-20F
LTC 0385/20
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
570
focal
EIA, 24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Monochrome
focal
KBE-385V55-20U LTC 0385/20
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
570
EIA, 24 VAC, 60 Hz, w/
Fiber
5-50 mm Vari- Outdoor, Monochrome
focal
EIA, 24 VAC, 60 Hz, w/
UTP
1/2 in. HIGH RESOLUTION, HIGH SENSITIVITY
KBE-510V75-20
LTC 0510/20 LTC 3274/41
KBE-510V75-20F
LTC 0510/20
KBE-510V75-20U LTC 0510/20
KBE-510V41-20
LTC 0510/20
F01U065975 | 1.0 | 2007.04
LTC 3274/41
LTC 3274/41
LTC 3764/20
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
Instruction Manual
570
7.5-75mm
Outdoor, Monochrome
570
Vari-focal
7.5-75mm
EIA, 24 VAC, 60 Hz
Outdoor, Monochrome
Vari-focal
EIA, 24 VAC, 60 Hz, w/
7.5-75mm
Fiber
Outdoor, Monochrome
Vari-focal
EIA, 24 VAC, 60 Hz, w/
4.0-12mm
UTP
Outdoor, Monochrome
Vari-focal
EIA, 24 VAC, 60 Hz
570
570
Bosch Security Systems, Inc.
KBE and KBN Series
Model No.
Camera
KBE-510V41-20F LTC 0510/20
KBE-510V41-20U LTC 0510/20
Model Numbers and System Specifications | en 9
Lens
LTC 3764/20
LTC 3764/20
Housing
UHO-HBGS-10
UHO-HBGS-10
Mount
LTC 9215/00
LTC 9215/00
Resolution Included Lens System
570
4.0-12mm
Outdoor, Monochrome
570
Vari-focal
EIA, 24 VAC, 60 Hz, w/
4.0-12mm
Fiber
Outdoor, Monochrome
Vari-focal
EIA, 24 VAC, 60 Hz, w/
UTP
COLOR 1/3 in. STANDARD RESOLUTION
KBN-435V28-20 LTC 0435/20 LTC 3364/50
LTC 9480/00
LTC 9215/00S
330
2.8-10 mm
Indoor, Color NTSC,
24 VAC, 60 Hz
Outdoor, Color NTSC,
KBE-435V28-20
LTC 0435/20
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
330
Vari-focal
2.8-10 mm
KBN-435V55-20
LTC 0435/20
LTC 3374/50
LTC 9480/00
LTC 9215/00S
330
Vari-focal
24 VAC, 60 Hz
5-50 mm Vari- Indoor, Color NTSC,
KBE-435V55-20
LTC 0435/20
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
330
focal
24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Color NTSC,
1/3 in. HIGH RESOLUTION
KBN-455V28-20 LTC 0455/21
LTC 3364/50
LTC 9480/00
LTC 9215/00S
focal
24 VAC, 60 Hz
540
2.8-10 mm
Indoor, Color NTSC,
24 VAC, 60 Hz
Outdoor, Color NTSC,
KBE-455V28-20
LTC 0455/21
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
2.8-10 mm
KBN-455V55-20
LTC 0455/21
LTC 3374/50
LTC 9480/00
LTC 9215/00S
540
Vari-focal
24 VAC, 60 Hz
5-50 mm Vari- Indoor, Color NTSC,
KBE-455V55-20
LTC 0455/21
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
540
focal
24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Color NTSC,
1/3 in., HIGH RESOLUTION, HIGH SENSITIVITY
KBN-485V28-20 LTC 0485/21 LTC 3364/50 LTC 9480/00
LTC 9215/00S
focal
24 VAC, 60 Hz
540
2.8-10 mm
Indoor, Color NTSC,
24V AC, 60 Hz
Outdoor, Color NTSC,
KBE-485V28-20
LTC 0485/21
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
2.8-10 mm
KBE-485V28-20F
LTC 0485/21
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
2.8-10 mm
24 VAC, 60 Hz
Outdoor, Color NTSC,
KBE-485V28-20U LTC 0485/21
LTC 3364/50
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
2.8-10 mm
24 VAC, 60 Hz, w/Fiber
Outdoor, Color NTSC,
KBN-485V55-20
LTC 0485/21
LTC 3374/50
LTC 9480/00
LTC 9215/00S
540
Vari-focal
24 VAC, 60 Hz, w/UTP
5-50 mm Vari- Indoor, Color NTSC,
KBE-485V55-20
LTC 0485/21
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
540
focal
24V AC, 60 Hz
5-50 mm Vari- Outdoor, Color NTSC,
KBE-485V55-20F
LTC 0485/21
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
540
focal
24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Color NTSC,
KBE-485V55-20U LTC 0485/21
LTC 3374/50
UHO-HBGS-10
LTC 9215/00
540
focal
24 VAC, 60 Hz, w/Fiber
5-50 mm Vari- Outdoor, Color NTSC,
1/2 in. HIGH RESOLUTION, HIGH SENSITIVITY
KBE-610V75-20
LTC 0610/21 LTC 3274/41
UHO-HBGS-10
LTC 9215/00
focal
24 VAC, 60 Hz, w/UTP
540
7.5-75mm
Outdoor, Color NTSC,
24 VAC, 60 Hz
Outdoor, Color NTSC,
24 VAC, 60 Hz, w/Fiber
Outdoor, Color NTSC,
LTC 0610/21
LTC 3274/41
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
7.5-75mm
KBE-610V75-20U LTC 0610/21
LTC 3274/41
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
7.5-75mm
KBE-610V41-20
LTC 3764/20
UHO-HBGS-10
LTC 9215/00
540
Vari-focal
24 VAC, 60 Hz, w/UTP
4-12 mm Vari- Outdoor, Color NTSC,
KBE-610V75-20F
LTC 0610/21
focal, IR
KBE-610V41-20F
LTC 0610/21
LTC 3764/20
UHO-HBGS-10
LTC 9215/00
540
focal, IR
KBE-610V41-20U LTC 0610/21
LTC 3764/20
UHO-HBGS-10
LTC 9215/00
540
24 VAC, 60 Hz
Corrected
4-12 mm Vari- Outdoor, Color NTSC,
24 VAC, 60 Hz, w/Fiber
Corrected
4-12 mm Vari- Outdoor, Color NTSC,
focal, IR
24 VAC, 60 Hz, w/UTP
Corrected
Bosch Security Systems, Inc.
Instruction Manual
F01U065975 | 1.0 | 2007.04
10 en | Model Numbers and System Specifications
Model No.
Camera
Lens
DAY/NIGHT 1/3 in. HIGH RESOLUTION
KBN-495V28-20 LTC 0495/21 LTC 3664/40
KBE-495V28-20
KBE-495V28-20F
LTC 0495/21
LTC 0495/21
KBE-495V28-20U LTC 0495/21
KBN-495V75-20
KBE-495V75-20
KBE-495V75-20F
LTC 0495/21
LTC 0495/21
LTC 0495/21
KBE-495V75-20U LTC 0495/21
LTC 3664/40
LTC 3664/40
LTC 3664/40
LTC 3674/20
LTC 3674/20
LTC 3674/20
LTC 3674/20
DAY/NIGHT 1/2 in. HIGH RESOLUTION
KBE-620V14-20
LTC 0620/21 LTC 3774/30
KBE-620V14-20F
LTC 0620/21
KBE-620V14-20U LTC 0620/21
KBE-620V41-20
LTC 0620/21
LTC 3774/30
LTC 3774/30
LTC 3764/20
KBE and KBN Series
Housing
Mount
LTC 9480/00 LTC 9215/00S
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
LTC 9480/00
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00S
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
Resolution Included Lens System
540
540
540
540
540
540
540
540
540
540
540
540
2.8-11 mm
Indoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
2.8-11 mm
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
2.8-11 mm
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
2.8-11 mm
w/Fiber
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
7.5-50 mm
w/UTP
Indoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
7.5-50 mm
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
7.5-50 mm
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
7.5-50 mm
w/Fiber
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
w/UTP
10-40 mm
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
10-40 mm
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
10-40 mm
w/Fiber
Outdoor, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
w/UTP
4-12 mm Vari- Outdoor, Day/Night
focal, IR
KBE-620V41-20F
LTC 0620/21
LTC 3764/20
UHO-HBGS-10
LTC 9215/00
540
NTSC, 24 VAC, 60 Hz
Corrected
4-12 mm Vari- Outdoor, Day/Night
focal, IR
KBE-620V41-20U LTC 0620/21
LTC 3764/20
IP, COLOR 1/3 in. HIGH RESOLUTION
KBE-455V28-20N NWC-0455-20P LTC 3364/50
KBE-455V55-20N NWC-0455-20P LTC 3374/50
IP, DAY/NIGHT 1/3 in. HIGH RESOLUTION
KBE-495V28-20N NWC-0495-20P LTC 3664/40
KBE-495V75-20N NWC-0495-20P LTC 3674/20
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
UHO-HBGS-10
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
LTC 9215/00
540
NTSC, 24 VAC, 60 Hz,
Corrected
w/Fiber
4-12 mm Vari- Outdoor, Day/Night
focal, IR
NTSC, 24 VAC, 60 Hz,
Corrected
w/UTP
540
2.8-10 mm
Outdoor, Color IP
540
Vari-focal
NTSC, 24 VAC, 60 Hz
5-50 mm Vari- Outdoor, Color IP
540
540
focal
NTSC, 24 VAC, 60 Hz
2.8-11 mm
Outdoor, IP, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
7.5-50 mm
Outdoor, IP, Day/Night
Vari-focal, IR
NTSC, 24 VAC, 60 Hz
Corrected
F01U065975 | 1.0 | 2007.04
Instruction Manual
Bosch Security Systems, Inc.
KBE and KBN Series
Bosch Security Systems, Inc.
Model Numbers and System Specifications | en 11
Instruction Manual
F01U065975 | 1.0 | 2007.04
Americas:
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450
USA
Phone
+1 800 289 0096
Fax
+1 585 223 9180
www.boschsecurity.us
Europe, Middle East, Asia:
Bosch Security Systems B.V.
Postbus 80002
5600 JB Eindhoven
Phone:
+31 40 2577 200
Fax:
+31 40 2577 202
nl.securitysystems@bosch.com
www.boschsecurity.nl
www.boschsecurity.com
© Bosch Security Systems, Inc., 2007; F01U065975 | 1.0 | 2007.04
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Phone
+65 6319 3450
Fax
+65 63139 3499
www.boschsecurity.com