advertisement
CyberView
User Manual
RKP115
RKP117
1U
Rackmount LCD monitor Keyboard drawer
Version 1.0
User Manual
Table of Contents
2.1 Display & Navigation Using Membrane Keys ................................................... 5
6.1 The LCD does not function, the PC input is operational .................................. 12
6.2 The message ‘Check Cable’ appears on the LCD............................................ 12
6.3 The message ‘No Sync’ appears on the LCD .................................................. 12
6.4 The message ‘Signal out of Range’ appears on the LCD ................................. 12
www.austin-hughes.co.uk Page 2
User Manual
1.0 General
1.1 Unit Introduction
Thank you for purchasing the 1U Rackmount LCD monitor Keyboard drawer. The unit offers space saving leading edge, flexible, features.
1.2 Unit Photograph
1.3 Unit Features
• 15 or 17 inch TFT/LC active matrix color
• Built in OSD (On Screen Display) controlled by integral membrane keys
• Single external 12V 5A remote power adaptor, easy to replace and ensures only a single power source is required to the unit , reducing the capacity of UPS outputs required
1.4 Unit Packing Contents
Model Number
RKP115 / 117 1U LCD Keyboard Drawer
User Manual CD
Quick Reference Guide
AC to DC Power Adaptor
Rack Mount Kit
115 117
1 1
1 1
1 1
1 1
1 1
1.5 Important Information & Safeguards
• Please read these safety instructions carefully
• Keep this user manual for later reference
• Disconnect the unit from the mains input power supply source before cleaning
• Do not spray aerosol or liquid cleaners directly on the unit, use only a soft cloth for cleaning
• Clean the LCD only with a soft anti static cloth
• Avoid placing pressure on the LCD to prevent permanent damage
• Rest the unit on a reliable surface when installing, a drop or fall may cause injury
• Please note all cautions and warnings on the equipment
• Never open the unit. Only qualified personnel should open the unit www.austin-hughes.co.uk Page 3
User Manual
• Refer to section
of this user manual regarding recommended storage and operating conditions for the unit
of this user manual regarding troubleshooting of the unit
of this user manual regarding improper use of the unit
1.6 Preparation for Use
• Carefully remove the unit from its packaging
• Please check that the unit and its accessories match the packing contents in section 1.4
of this user manual
• Please read this user manual thoroughly familiarising yourself with the unit
• Place the unit on a protected work surface and carefully slide open the keyboard drawer noting the friction stops on the slides to prevent movement of the keyboard whilst in use
• Carefully slide open and lift the LCD screen to a convenient viewing angle
• Plug up the DC power supply, whilst noting that the green LED on the external adaptor should now be lit
• You should now be able to see the LED lights on the unit functioning you could also follow
to familiarise yourself with the OSD (On screen display) of the unit
• After removing the DC power input, carefully install the unit into the rack, noting section
of this user manual - important information and safe guards, and plug in all connecting
hardware (ensure all connecting hardware is powered down for this stage of the install)
• Further information regarding the use of this unit can be found in the following sections of this user manual www.austin-hughes.co.uk Page 4
User Manual
2. LCD On Screen Display
2.1 Display & Navigation Using Membrane Keys
The On screen display built into the unit provides users with an efficient method of adjusting to the display input signal. This section explains clearly how to navigate the OSD using the membrane keys, shown below, that you will find on the unit to the right side of the LCD screen.
Exit Menu or sub menu
Display OSD or scroll / select
Input Value + or up / left scroll
Input Value – or down / right scroll
LCD Display On / Off
2.1.1 To display the OSD
Simply press the key marked www.austin-hughes.co.uk Page 5
2.1.2 To Select a Menu Item
Simply press the key to scroll
2.1.3 To Enter the Sub Menu
Simply press the key marked
2.1.4 To Change an Input Value
Simply use the key marked
2.1.5 To Save the setting
Simply press the key marked
2.1.6 To Exit the Main Menu
Simply use the key marked
2.2 Customizing the LCD Settings
2.2.1 Brightness / Contrast
To adjust brightness - follow steps 2.1.1
2.2.2 Auto Adjust
To auto adjust - follow steps 2.1.1
through 2.1.5
NOTE -: While the OSD Menu is NOT displayed the key acts as Auto Adjust
User Manual www.austin-hughes.co.uk Page 6
User Manual
2.2.3 Phase / Clock
To optimize display qualities - follow the steps 2.1.1
2.2.4 Horizontal Screen Position
To adjust horizontal screen position - follow the steps 2.1.1
through 2.1.5
2.2.5 Vertical Screen Position
To adjust horizontal screen position - follow the steps 2.1.1
through 2.1.5
2.2.6 To reset to default factory setting
To reset - follow the steps
3. Miscellaneous Sub Menu
To select miscellaneous sub menu - follow the steps
www.austin-hughes.co.uk Page 7
3.1.1 Information
To select information sub menu - follow the steps 2.1.1
through 2.1.5
3.1.2 OSD Timeout
To select OSD Timeout sub menu - follow the steps 2.1.1
through 2.1.5
3.1.3 Color
To select Color sub menu - follow the steps 2.1.1
through 2.1.5
User Manual www.austin-hughes.co.uk Page 8
User Manual
3.1.4 OSD language
To select the OSD language sub menu - follow the steps
4. Setting OS Refresh Rate - Microsoft Windows®
On the windows desktop ‘right click’ the mouse key and then select ‘properties’
Select ‘Settings’ from the tab menu
Select ‘Monitor’ and then select a Screen refresh Rate of 75 Hertz – Press OK to save and exit www.austin-hughes.co.uk
Page 9
User Manual
5. LCD Technical Specification
LCD Size
Screen Area
Display Area
Contrast Ratio
Viewing Angle
Resolution
Pixel Pitch
Response Time
Brightness
Panel Color
Back Light
Power
Management
Range
Input Signal
Power
OSD Control
Power Input
Video Input
15"
TFT Active Matrix
304.1mm (h) x 228.1mm (V)
300:1
130 deg (H) z 115 deg (V) TYP
1024 x 768 XGA
0.297mm (H) x 0.297mm (W)
Tr = 5ms, TF = 20ms TYP
250 cd/m2
16.2M Colors
4 Lamps
Vertical 56-75 Hz
Analog RGB 0.7Vp-p
VESA DPMS
Micro on/off switch
Brightness, Contrast, Color, H
Position, V Position, Auto Config,
OSD Adjust, Dither, etc
12V/5A DC Adaptor
15-Pin D-sub connector www.austin-hughes.co.uk Page 10
User Manual
LCD Size
Screen Area
Display Area
Contrast Ratio
Viewing Angle
Resolution
Pixel Pitch
Response Time
Brightness
Panel Color
Back Light
Range
Input Signal
Power
Management
Power
OSD Control
Power Input
Video Input
17"
TFT Active Matrix
337:92mm (h) x 270.336mm (V)
350:1
150 deg (H) z 125 deg (V) TYP
1280 x 1024 SXGA
0.264mm (H) x 0.264mm (W)
Tr = 5ms, TF = 20ms TYP
250 cd/m2
16.7M Colors
4 Lamps
Vertical 56-75 Hz
Analog RGB 0.7Vp-p
VESA DPMS
Micro on/off switch
Brightness, Contrast, Color, H
Position, V Position, Auto Config,
OSD Adjust, Dither, etc
12V/5A DC Adaptor
15-Pin D-sub connector www.austin-hughes.co.uk Page 11
User Manual
6. LCD Troubleshooting
6.1 The LCD does not function, the PC input is operational
• Ensure that the Power adaptor is securely plugged in at both ends and has power feed from the supply source; check that the Green led light is on on the adaptor unit
•
Ensure the LCD is on by pressing the key
•
Ensure that the LCD is pulled out past the micro switch threshold
6.2 The message ‘Check Cable’ appears on the LCD
• The VGA cable input cable is not connected properly
6.3 The message ‘No Sync’ appears on the LCD
•
The message indicates that there is no input signals from the PC, make sure the PC is functioning and that the graphics card is installed correctly
.
6.4 The message ‘Signal out of Range’ appears on the LCD
• This message indicates that the input signal is beyond the LCD capability – The maximum resolution for the screen is 1024 x 768 at 75 Hz Check PC and Operating System output refer
www.austin-hughes.co.uk Page 12
User Manual
7. Warranty
7.1 Period & Conditions
Warranty is from the date of sale of the unit, subject to the terms and conditions of the Austin
Hughes Europe Authorised channel partner who supplied the unit, please refer to your authorised channel partner for terms & conditions
7.2 Manufacturers exclusions
7.2.1 or removed
Any Unit on which the Austin Hughes serial number has been defaced, modified
7.2.2 Damage, deterioration, or malfunction resulting from – accident, misuse, neglect, fire, water, lightening, or other acts of nature
7.2.3 Unauthorised unit modification
7.2.4 Unauthorised unit repair, by other than an Austin Hughes Europe authorised channel partner
7.2.5 Damage to the unit caused by installation or removal, unless covered by Austin
Hughes Europe channel partner services warranty
7.2.6 Use of unauthorised parts not meeting Austin Hughes Europe specifications
7.2.7 Other causes of damage unrelated to product defect including wear and tear
7.2.8 Damage to the unit caused by transit
8. Disclaimer
This information is subject to change without notice. Austin Hughes Europe accept no responsibility for damage or claims, resulting from misuse or misinterpretation of this information www.austin-hughes.co.uk Page 13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project