Zanussi ZU 9145 Specifications

KÜHLSCHRANK
REFRIGERATOR
ХOЛОДИЛЬНИК
FRIGORÍFICO
ZU 9145
D
t
T
P
BEDIENUNGSANLEITUNG
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
2222681-88
Downloaded from Fridge-Manual.com Manuals
INSTRUCTION BOOKLET
INSTRUÇÕES DE USO
CONTENTS
Instructions for the User
Instructions for the Installer
Important Safety Instructions
15
Technical specifications
20
Description of the Appliance
16
Installation
20
17
Positioning
Electrical connection
Use
Cleaning the interior
Starting-up
Temperature control
Fresh food refrigeration
Movable shelves
Positioning the door shelves
Hints
Hints for refrigeration
Maintenance
Defrosting
Periodic cleaning
Periodic of non-operation
Interior light
Customer Service and
Spare Parts
17
17
17
17
17
17
Building-in instructions
Grid preparation
Door reversal
Building in the appliance under a worktop
Fitting the plinth
18
18
18
18
19
19
19
20
Downloaded from Fridge-Manual.com Manuals
14
20
20
21
21
21
22
23
IMPORTANT SAFETY
INSTRUCTIONS
t
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is supplied with the appliance in order that the new
owner can be acquainted with the functioning of the appliance and the relevant warnings.
These warnings are provided in the interest of safety. You must read them carefully before installing or
using the appliance.
General Safety
■
■
■
■
■
■
■
■
■
■
■
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
It is dangerous to alter the specifications or modify
this product in any way.
Before any cleaning or maintenance work is
carried out, be sure to switch off and unplug the
appliance.
This appliance is heavy. Care should be taken
when moving it.
Ice follies can cause frost burns if consumed
straight from the appliance.
Take utmost care when handling your
appliance so as not to cause any damages to
the cooling unit with consequent possible fluid
leakages.
The appliance must not be located close to
radiators or gas cookers.
Avoid prolonged exposure of the appliance to
direct sunlight.
There must be adequate ventilation round the
back of the appliance and any damage to the
refrigerant circuit must be avoided.
For freezers only (except built-in models): an
ideal location is the cellar or basement.
Do not use other electrical appliances (such as
ice cream makers) inside of refrigerating
appliances.
■
Use
■
■
■
■
■
Service / Repair
■
■
■
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
This appliance should be serviced by an
authorised Service Centre, and only genuine
spare parts should be used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
more serious malfunctioning. Refer to your local
Service Centre, and always insist on genuine
spare parts.
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging must
therefore only be carried out by authorised
technicians.
The domestic refrigerators and freezers are
designed to be used specifically for the storage of
edible foodstuffs only.
Frozen food must not be re-frozen once it has
been thawed out.
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
The inner lining of the appliance consists of
channels through which the refrigerant passes. If
these should be punctured this would damage the
appliance beyond repair and cause food loss. DO
NOT USE SHARP INSTRUMENTS to scrape off
frost or ice. Frost may be removed by using the
scraper provided. Under no circumstances should
solid ice be forced off the liner. Solid ice should be
allowed to thaw when defrosting the appliance.
See defrost instructions.
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to speed
up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it may
get damaged.
Installation
■
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly
available from the manufacturer or its service
agent.
■
During normal operation, the condenser and
compressor at the back of the appliance heat up
Downloaded from Fridge-Manual.com Manuals
15
■
■
■
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
paragraph.
Attention: keep ventilation openings clear
of obstruction.
If the appliance is transported horizontally, it is
possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to
flow back in the compressor.
There are working parts in this product which heat
up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
■
If the appliance has been transported horizontally,
it is possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
■
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from your
municipal authorities.
The materials used on this appliance marked
with the symbol
are recyclable.
Environment Protection
■
DESCRIPTION OF THE APPLIANCE
➀ Butter shelf
➁ Sliding shelf
➂ Bottle shelf
➃ Airduct exit
➄ Air inlet filter
➅ Salad bins
➆ Storage shelves
➇ Thermostat
➀
➇
➁
➆
➅
➄
Downloaded from Fridge-Manual.com Manuals
16
➂
➃
t
USE
Cleaning the interior
Fresh food refrigeration
Before using the appliance for the first time, wash the
interior and all internal accessories with lukewarm
water and some neutral soap so as to remove the
typical smell of a brand-new product, then dry
thoroughly.
Do not use detergents or abrasive powders,
as these will damage the finish.
The refrigerator compartment is suitable for cooling
drinks and for normal food storing.
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator and do
cover or wrap up the food, particularly if it has a
strong smell.
Starting-up
Insert the plug into the wall socket.
Open the door and turn the thermostat control knob,
to be found on the upper right hand side of the inner
compartment, clockwise beyond position «O» (OFF)
to start the appliance.
Movable shelves
The walls of the refrigerator are equipped with a
series of runners so that the shelves can be
positioned as desired.
Temperature control
Temperature adjustment is obtained by turning the
thermostat knob clockwise until its pointer coincides
with the required setting.
A medium setting is generally the most suitable.
The minimum setting (least cold) is represented by
the lowest number and the maximum setting (coldest)
by the highest number. In any case, bear in mind that
the temperature can be either increased (warmer) by
turning the thermostat knob anticlockwise or
decreased (colder) by turning it clockwise.
The thermostat knob setting should be adjusted
depending on the inner temperature of the
refrigerator, which, in turn, depends on a number of
factors, such as: the ambient temperature, the
number of times the door is opened, the quantity of
food stored and the location of the appliance.
D040
Positioning the door shelves
The short shelf can be adjusted in the direction of the
arrows.
For more thorough cleaning, the top and bottom door
sheves can be removed by pulling them in the
direction of the arrows, then refitting them in position.
Warning
If the ambient temperature is high, the
thermostat knob is on the coldest setting
(higher numbers) and the appliance is fully
loaded, the compressor may run
continuously, causing frost or ice to form
on the evaporator. If this happens, turn the
knob to a warmer setting (lower numbers)
to allow automatic defrosting and so a
saving in electricity consumption.
Downloaded from Fridge-Manual.com Manuals
17
HINTS
Hints for refrigeration
To help you use your refrigerator correctly, here are
some useful hints:
1
Cooked food, cold cuts, jelly, etc.: these
should be well covered and can be stored on any of
the glass shelves.
1
2
Raw meat (beef, pork, lamb & poultry):
wrap in polythene bags and place on top of the salad
compartment, this being the coldest spot in the
refrigerator.
Meat can only be stored safely in this way for one
or two days at the most.
2
3
S.I.009
3
Fruit & vegetables: these should be
thoroughly cleaned and placed in the bottom drawer.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to keep out as much air as possible.
Milk bottles: these should have a top and should be
stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
MAINTENANCE
Unplug the appliance before carrying out
any maintenance operation.
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.
Defrosting
Frost is automatically eliminated from the evaporator
of the refrigerator compartment every time the motor
compressor stops, during normal use.
The defrost water drains out through a trough into a
special container at the back of the appliance, over the
motor compressor, where it evaporates.
It is important to periodically clean the defrost
water drain hole (F) situated under the salad
drawers to prevent the water overflowing and
dripping onto the food inside. Use the special
cleaner provided (P), which you will find already
inserted into the drain hole.
Downloaded from Fridge-Manual.com Manuals
18
P
S.I.011
F
t
Periodic cleaning
Never use metal objects for clearing your appliance as
it may get damaged. Clean the inside with warm water
and bicarbonate of soda. Rinse and dry thoroughly.
The appliance is equipped with an air inlet filter (1)
and an air outlet duct (2) on the ventilation grid. Keep
clean to guarantee good ventilation and good working
order of the appliance.
2
The filter can be removed and washed with water, as
follows:
1. Pinch flaps (a) and (b) with fingers
2. Pull the filter down.
3. Pull the filter out.
To replace the filter reverse the process.
b
a
1
S.I.012
The appliance is equipped with a ventilation grid. Keep
clean to guarantee good ventilation and good working
order of the appliance.
An accumulation of dust will affect the performance of
the appliance and cause excessive electricity
consumption.
The structure of the appliance permits cleaning of the
rear zone close to the wall, using a vacuum cleaner.
1. Remove the plinth (1), then the ventilation grid (2);
2. Carefully pull the air deflector out (3), checking that
there is no water left from the defrosting.
3
S.I.013
Periods of non-operation
When the appliance is not in use for long periods, take
the following precautions:
remove the plug from the wall socket;
remove all food:
defrost and clean the interior and all accessories;
leave the door ajar to allow air to circulate to prevent
unpleasant smells.
Interior light
The light bulb inside the refrigerator compartment can
be reached as follows:
1. unscrew the light cover securing screws;
2. unhook the moving part by pressing it as shown in
the figure.
If the door is open and the light does not come on,
check that the bulb is properly screwed in; if it still
does not work, replace the bulb with one of the same
power.
The maximum rating is shown on the light cover.
D411
Downloaded from Fridge-Manual.com Manuals
19
2
1
CUSTOMER SERVICE AND
SPARE PARTS
If the appliance is not functioning properly, check that:
the plug is firmly in the wall socket and the mains
power switch is on;
there is an electricity supply (find out by plugging in
another appliance);
the thermostat knob is in the correct position.
If there are water drops on the bottom of the cabinet,
check that the defrost water drain opening is not
obstructed (see "Defrosting" section).
If your appliance is still not working properly after
making the above checks, contact the nearest service
centre.
To obtain fast service, it is essential that when
you apply for it you specify the model and serial
number of your appliance which can be found on
the guarantee certificate or on the rating plate
located inside the appliance, on the bottom righthand side.
TECHNICAL SPECIFICATIONS
The technical data is indicated in the rating plate on the right side inside the appliance.
Height 815 mm
Width 560 mm
Depth 538 mm
INSTALLATION
lf this appliance featuring magnetic door seals is
to replace an older appliance having a spring lock
(latch) on the door or lid, be sure to make that
spring lock unusable before you discard the old
appliance. This will prevent it from becoming a
death-trap for a child.
Positioning
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.
Best performance is obtained with ambient
temperature between +18°C and +43°C (class T);
+18°C and +38°C (class ST); +16°C and +32°C
(class N); +10°C and +32°C (class SN).
The class of your appliance is shown on its rating
plate.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.
Important
The appliance must be earthed.
The power supply cable plug is provided with a
contact for this purpose.
If the domestic power supply socket is not
earthed. connect the appliance to a separate
earth in compliance with current regulations,
consulting a specialist technician.
The Manufacturer declines all responsibility if the
above safety precautions are not observed.
Attention!
It must be possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
For building-in and door reversibility refer to the
relevant instructions.
Downloaded from Fridge-Manual.com Manuals
20
This appliance complies with the following
E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and
subsequent modifications;
- 87/308 EEC of 02/06/87 (Radio Interference
Suppression Directive) and subsequent
modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
t
BUILDING-IN INSTRUCTIONS
Before carrying out any work, remove the plug from
the power socket.
Grid preparation
a
Remove the grid from the appliance pulling it towards
you with hands.
Right door opening:
a
Remove the left side (A) of the grid cutting it from the
rear (see figure, a).
Left door opening:
Remove the right side (B) of the grid cutting it from the
rear (see figure, b).
S.I.001
To reposition the grid on the appliance proceed as
follows:
Apply the grid to the base of the appliance by pushing
the clasps (a) until they click.
N.B. The grid is to be assembled after having fixed the
appliance in the niche with the brackets.
a
A
B
b
S.I.002
Door reversal
The appliance must be unplugged before starting
work. To reverse the opening direction of the door,
proceed as follows:
1. remove the top hinge (1) taking care not to let the
door fall;
2. remove the bottom door hinge (2).
3. take out the plugs (3) from the holes (F) and
reinsert them in the holes (F1) on the opposite side;
4. refit the upper hinge (1) on the opposite side, on the
bottom (position A);
5. refit the door on the pin of the hinge (1) in position
A;
6. insert the pin of the unscrewed bottom hinge (2) in
the upper hole (G) of the door, therefore fix the
hinge on the top in position B.
Important
After completion of the door reversal operation,
verify that the door gasket is sealing onto the
cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to the
Downloaded from Fridge-Manual.com Manuals
21
F1
F
1
B
G
3
A
F
F1
2
S.I.003
cabinet. In that case, wait for the natural
fitting of the gasket or accelerate this
process by heating up the part involved with
a normal hairdryer on a low setting.
Building the appliance in under a
worktop
The dimensions of the recessed installation area must
correspond with those indicated in the figure.
60
0
30
S.I.006
820 - 870
55
0
600
a
600
b
3. The appliance is equipped with adjustable support
feet. To adapt the appliance to the height of the
installation area (max 870 mm), screw in, or screw
out the feet situated at each bottom corner.
S.I.004
The appliance could be inserted between two units
(a) or as an end unit (b).
UPPER
SUPER.
B
A
LOWER
INFER.
C
D
PR266
4. Separate parts A, B, C, D as shown in the figure.
D326
UPPER
SUPER.
50mm
1. Fasten the side panel to the rear of the appliance
with the fixing brackets.
A
LOWER
INFER.
E
20m
m
E
PR166
D319
5. Place guide (A) on the inside part of the furniture
door, in the upper and lower positions as shown in
the figure and mark the position of external holes.
After having drilled holes, fix the guide with the
screws supplied.
2. Fasten the appliance to the worktop or the sides,
applying the sealing strip between the refrigerator
and adjacent cabinet using the fixing brackets (E).
Downloaded from Fridge-Manual.com Manuals
22
t
A
B
C
D
PR3 3 /2
PR167/1
6. Push cover (C) into guide (A) until it clips into
place.
9. Push cover (D) into guide (B) until it clips into
place.
Fitting the plinth
8mm
A
PR167
B
S.I.007
Important
For the efficient operation of the appliance,
it is important that the original ventilation
grid is used.
■
For an opening height dimension A=820 mm and a
plinth height dimension a=100 mm, the plinth may
be fitted without adjustments. The same applies to
an opening height dimension B=870 mm and a
plinth height dimension b=150 mm.
a = 100
b = 150
A = 820
B = 870
7. Open the appliance door and the furniture door at
90°. Insert the small square (B) into guide (A). Put
together the appliance door and the furniture door
and mark the holes as indicated in the figure.
Remove the squares and drill holes with Ø 2 mm at
8 mm from the outer edge of the door. Place the
small square on the guide again and fix it with the
screws supplied.
PR168
8. Should adjustment of the furniture door be
necessary, use the clearance of slots.
At the end of operations, it is necessary to check if
the door of the furniture closes properly.
580
25
- 80
25
■
■
For plinth
S.I.008
heights greater
than a=100 mm, b=150 mm, a cut should be made
in the plinth, 580 mm wide, in the centre of the
appliance position, leaving a remaining height of
a=100 mm, b=150 mm.
Attach plinth to the kitchen units.
Important
The plinth must be positioned at a minimun
distance of 25 mm from the door.
Downloaded from Fridge-Manual.com Manuals
23
Downloaded from Fridge-Manual.com Manuals